THVD1400, THVD1420

SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

THVD1400, THVD1420 3.3-V to 5-V RS-485 Transceivers in Small Package

with ±12-kV IEC ESD Protection

1 Features Description
• Meets or exceeds the requirements of the TIA/ THVD1400 and THVD1420 are robust half-duplex
EIA-485A standard RS-485 transceivers for industrial applications. The
• 3-V to 5.5-V Supply voltage bus pins are immune to high levels of IEC Contact
• Half-duplex RS-422/RS-485 Discharge ESD events, eliminating the need for
• Data rates additional system level protection components.
– THVD1400: 500 kbps The devices operate from a single 3 to 5.5-V supply.
– THVD1420: 12 Mbps The wide common-mode voltage range and low input
• Bus I/O protection leakage on bus pins make the devices suitable for
– ±16-kV HBM ESD multi-point applications over long cable runs.
– ±12-kV IEC 61000-4-2 Contact discharge
– ±15-kV IEC 61000-4-2 Air gap discharge THVD1400 and THVD1420 are available in
– ±4-kV IEC 61000-4-4 Fast transient burst industry standard, 8-pin SOIC package for drop-in
– ±16-V bus fault protection (absolute max compatibility as well as in the industry-leading, small
voltage on bus pins) SOT package. The devices are characterized for
• Small, space-saving 8-pin SOT package option ambient temperatures from –40°C to 125°C.
(2.1 mm x 1.2 mm) Device Information
– See the layout example for co-layout with PART NUMBER PACKAGE(1) BODY SIZE (NOM)
standard SOIC-8 package SOT (8) 2.1 mm x 1.2 mm
THVD1400
• Extended industrial temperature range: -40°C to THVD1420 SOIC (8) 4.90 mm × 3.91 mm
125°C
• Large receiver hysteresis for noise rejection (1) For all available packages, see the orderable addendum at
• Low power consumption the end of the data sheet.
– Low standby supply current: < 1 µA
– Quiescent current during operation: 1.5 mA
(typ)
• Glitch-free power-up/down for hot plug-in capability
• Open, short, and idle bus failsafe 1
R
• 1/8 Unit load (Up to 256 bus nodes)
2 7
2 Applications RE B
• Factory automation & control 3 6
A
• Building automation DE
• Grid infrastructure 4
• Motor drives D
• Power delivery
• Industrial transport
• HVAC systems Simplified Schematic
• Video surveillance
• Smart meters

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

Table of Contents
1 Features............................................................................1 7.3 Feature Description...................................................13
2 Applications..................................................................... 1 7.4 Device Functional Modes..........................................13
3 Revision History.............................................................. 2 8 Application Information Disclaimer............................. 15
4 Pin Configuration and Functions...................................3 8.1 Application Information............................................. 15
5 Specifications.................................................................. 4 8.2 Typical Application.................................................... 15
5.1 Absolute Maximum Ratings........................................ 4 9 Power Supply Recommendations................................19
5.2 ESD Ratings............................................................... 4 10 Layout...........................................................................20
5.3 ESD Ratings [IEC]...................................................... 4 10.1 Layout Guidelines................................................... 20
5.4 Recommended Operating Conditions.........................5 10.2 Layout Example...................................................... 20
5.5 Thermal Information....................................................5 11 Device and Documentation Support..........................22
5.6 Power Dissipation Characteristics.............................. 5 11.1 Device Support........................................................22
5.7 Electrical Characteristics.............................................6 11.2 Receiving Notification of Documentation Updates.. 22
5.8 Switching Characteristics (THVD1400).......................7 11.3 Support Resources................................................. 22
5.9 Switching Characteristics (THVD1420).......................7 11.4 Trademarks............................................................. 22
5.10 Typical Characteristics.............................................. 9 11.5 Electrostatic Discharge Caution.............................. 22
6 Parameter Measurement Information.......................... 11 11.6 Glossary.................................................................. 22
7 Detailed Description......................................................13 12 Mechanical, Packaging, and Orderable
7.1 Overview................................................................... 13 Information.................................................................... 22
7.2 Functional Block Diagrams....................................... 13

3 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision A (April 2021) to Revision B (October 2021) Page

• Updated IEC ESD Contact rating from 8 kV to 12 kV in the Features section................................................... 1
• Changed HBM rating for non-bus pins from 1kV to 4kV in the ESD Ratings table ...........................................4
• Changed the IEC ESD contact rating for bus pins from 8kV to 12kV in the ESD Ratings [IEC] table................4
• Updated the VIH max specification for the logic input pins from VCC to 5.5 V in the Recommended Operating
Conditions table.................................................................................................................................................. 5
• Updated IEC ESD Contact rating from 8 kV to 12 kV in the Features Description section.............................. 13
• Updated IEC ESD Contact rating from 8 kV to 12 kV in the Transient Protection section................................17

Changes from Revision * (December 2020) to Revision A (April 2021) Page

• Added Feature: See the layout example............................................................................................................ 1
• Deleted the Advanced Information note from THVD1420 in the Device Information table.................................1
• Added Figure 5-7, Figure 5-8 and Figure 5-9. ................................................................................................... 9
• Added test conditions for Figure 5-1, Figure 5-2, Figure 5-4 and Figure 5-5. ....................................................9
• Added Figure 10-2 ........................................................................................................................................... 20

2 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

4 Pin Configuration and Functions

R 1 8 VCC

RE 2 7 B

DE 3 6 A

D 4 5 GND

Not to scale

Figure 4-1. SOIC-8 (D), SOT-8 (DRL) Package, Top View

Table 4-1. Pin Functions

PIN
I/O DESCRIPTION
NAME NO.
R 1 Digital output Receive data output
RE 2 Digital input Receiver enable, active low (internal 2-MΩ pull-up)
DE 3 Digital input Driver enable, active high (internal 2-MΩ pull-down)
D 4 Digital input Driver data input
GND 5 Ground Device ground
A 6 Bus input/output Bus I/O port, A (complementary to B)
B 7 Bus input/output Bus I/O port, B (complementary to A)
VCC 8 Power 3.3-V to 5-V supply

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 3

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

5 Specifications
5.1 Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted (see (1))
MIN MAX UNIT
VCC Supply voltage –0.5 7 V
VL Input voltage at any logic pin (D, DE or RE) –0.3 5.7 V
VA, VB Voltage at A or B inputs –16 16 V
IO Receiver output current –24 24 mA
TJ Junction temperature 170 °C
TSTG Storage temperature –65 150 °C

(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute maximum ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.
If briefly operating outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not
sustain damage, but it may not be fully functional. Operating the device in this manner may affect device reliability, functionality,
performance, and shorten the device lifetime.

5.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) Bus terminals (A, B) and GND ±16,000 V
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) All other pins ±4,000
V(ESD) Electrostatic discharge V
Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) ±1,500

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

5.3 ESD Ratings [IEC]

VALUE UNIT
Electrostatic discharge IEC 61000-4-2 ESD (Contact Discharge), bus terminals and GND ±12,000
V(ESD) Electrostatic discharge IEC 61000-4-2 ESD (Air-Gap Discharge), bus terminals and GND ±15,000 V
Electrostatic discharge IEC 61000-4-4 EFT (Fast transient or burst), bus terminals and GND ±4,000

4 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

5.4 Recommended Operating Conditions

MIN NOM MAX UNIT
VCC Supply voltage 3 5 5.5 V
VID Differential input voltage –12 12 V
VI Input voltage at any bus terminal(1) –7 12 V
VIH High-level input voltage (driver, driver-enable, and receiver-enable inputs) 2 5.5 V
VIL Low-level input voltage (driver, driver-enable, and receiver-enable inputs) 0 0.8 V
Driver –60 60
IO Output current mA
Receiver –8 8
RL Differential load resistance 54 60 Ω
1/tUI Signaling rate: THVD1400 500 kbps
1/tUI Signaling rate: THVD1420 12 Mbps
TJ Junction temperature –40 150 °C
TA (2) Operating ambient temperature –40 125 °C
TSHDN Thermal shutdown threshold (temperature rising) 150 170 °C
THYS Thermal shutdown hysteresis 15 °C

(1) The algebraic convention in which the least positive (most negative) limit is designated as minimum is used in this data sheet.
(2) Operation is specified for internal (junction) temperatures up to 150°C. Self-heating due to internal power dissipation should be
considered for each application. Maximum junction temperature is internally limited by the thermal shut-down (TSD) circuit which
disables the driver outputs when the junction temperature reaches 170°C.

5.5 Thermal Information

THVD1400, THVD1420
THERMAL METRIC(1) DRL (SOT) D (SOIC) UNIT
8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance 112.2 126.0 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 28.4 66.2 °C/W
RθJB Junction-to-board thermal resistance 22.1 69.4 °C/W
ψJT Junction-to-top characterization parameter 1.2 18.7 °C/W
ψJB Junction-to-board characterization parameter 22.0 68.7 °C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.

5.6 Power Dissipation Characteristics

PARAMETER TEST CONDITIONS VALUE UNIT
Power dissipation, driver and Unterminated RL = 300 Ω, CL = 50 pF 145
receiver enabled, VCC = 5.5 V, TA =
RS-422 load RL = 100 Ω, CL = 50 pF 175
125°C, 50% duty cycle square-wave mW
signal at maximum signaling rate
RS-485 load RL = 54 Ω, CL = 50 pF 235
(THVD1400)
PD
Power dissipation, driver and Unterminated RL = 300 Ω, CL = 50 pF 175
receiver enabled, VCC = 5.5 V, TA =
RS-422 load RL = 100 Ω, CL = 50 pF 200
125°C, 50% duty cycle square-wave mW
signal at maximum signaling rate
RS-485 load RL = 54 Ω, CL = 50 pF 250
(THVD1420)

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 5

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

5.7 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
RL = 60 Ω, -7 V ≤ Vtest ≤ 12 V 1.5 2
RL = 60 Ω, -7 V ≤ Vtest ≤ 12 V, 4.5 V ≤ Vcc See Figure 6-1
2.1 3
≤ 5.5 V
Driver differential-output voltage
│VOD│ V
magnitude RL = 100 Ω, CL = 50 pF 2 2.5
RL = 54 Ω, CL = 50 pF See Figure 6-2 1.5 2
RL = 54 Ω, 4.5 V ≤ Vcc ≤ 5.5 V 2.1 3
Change in magnitude of driver
Δ│VOD│ –50 50 mV
differential-output voltage
Steady-state common-mode
VOC(SS) RL = 54 Ω or 100 Ω, CL = 50 pF See Figure 6-2 1 VCC / 2 3 V
output voltage
Change in differential driver
ΔVOC –50 50 mV
common-mode output voltage
Peak-to-peak driver common-
VOC(PP) RL = 54 Ω, CL = 50 pF, VCC = 5 V See Figure 6-2 520 mV
mode output voltage
Peak-to-peak driver common-
VOC(PP) RL = 54 Ω, CL = 50 pF, VCC = 3.3 V See Figure 6-2 250 mV
mode output voltage
Driver short-circuit output
│IOS│ DE = VCC, -7 V ≤ [VA or VB] ≤ 12 V, or A pin shorted to B pin -250 250 mA
current
Receiver

Bus input current (driver VI = 12 V 75 100

II DE = 0 V, VCC = 0 V or 5.5 V µA
disabled) VI = –7 V –97 –70
Positive-going receiver
VIT+ differential-input voltage –70 –45 mV
threshold
Negative-going receiver
VIT– differential-input voltage -7 V ≤ VCM ≤ 12 V –200 –150 mV
threshold
Receiver differential-input
VHYS (1) voltage threshold hysteresis 30 50 mV
(VIT+ – VIT– )
Receiver high-level output
VOH IOH = –4 mA VCC – 0.4 VCC – 0.2 V
voltage
Receiver low-level output
VOL IOL = 4 mA 0.2 0.4 V
voltage
Receiver high-impedance
IOZ VO = 0 V or VCC, RE = VCC –1 1 µA
output current
Logic
IIN Input current (D, DE, RE) –5 5 µA
Supply

6 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

5.7 Electrical Characteristics (continued)

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DE = VCC, RE =
Both driver and receiver enabled 1500 1800
0, no load
Driver enabled and receiver DE = VCC, RE =
1000 1500
VCC = 3.6 disabled VCC, no load
µA
V Driver disabled and receiver DE = 0, RE = 0,
700 900
enabled no load
DE = 0 , RE =
Both driver and receiver disabled 0.1 1
VCC, no load
ICC Supply current (quiescent)
DE = VCC, RE =
Driver and receiver enabled 1700 3000
0, no load
DE = VCC, RE =
Driver enabled, receiver disabled 1300 2500
VCC = 5.5 VCC, no load
µA
V DE = 0, RE = 0,
Driver disabled, receiver enabled 800 1000
no load
DE = 0, RE =
Both driver and receiver disabled 0.1 1
VCC, no load

(1) Under any specific conditions, VIT+ is specified to be at least VHYS higher than VIT–.

5.8 Switching Characteristics (THVD1400)

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
tr, tf Driver differential output rise and fall times 200 400 600 ns
tPHL, tPLH Driver propagation delay See Figure 6-3 250 500 ns
tSK(P) Driver pulse skew, |tPHL – tPLH| 15 ns
tPHZ, tPLZ Driver disable time 80 200 ns
See Figure
Receiver enabled 200 650 ns
tPZH, tPZL Driver enable time 6-4 and Figure 6-5
Receiver disabled 4 10 µs
Receiver
tr, tf Receiver output rise and fall times 13 20 ns
tPHL, tPLH Receiver propagation delay time See Figure 6-6 60 110 ns
tSK(P) Receiver pulse skew, |tPHL – tPLH| 7 ns
tPHZ, tPLZ Receiver disable time 30 60 ns
See Figure 6-7
tPZL(1), Driver enabled 60 150 ns
tPZH(1)
Receiver enable time
tPZL(2), Driver disabled See Figure 6-8 4 10 µs
tPZH(2)

5.9 Switching Characteristics (THVD1420)

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
tr, tf Driver differential output rise and fall times 15 25 ns
tPHL, tPLH Driver propagation delay See Figure 6-3 20 38 ns
tSK(P) Driver pulse skew, |tPHL – tPLH| 3.5 ns
tPHZ, tPLZ Driver disable time 15 38 ns
See Figure
Receiver enabled 15 70 ns
tPZH, tPZL Driver enable time 6-4 and Figure 6-5
Receiver disabled 4 10 µs
Receiver

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 7

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

5.9 Switching Characteristics (THVD1420) (continued)

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
tr, tf Receiver output rise and fall times 10 16 ns
tPHL, tPLH Receiver propagation delay time See Figure 6-6 40 75 ns
tSK(P) Receiver pulse skew, |tPHL – tPLH| 5 ns
tPHZ, tPLZ Receiver disable time 15 25 ns
See Figure 6-7
tPZL(1), Driver enabled 25 170 ns
tPZH(1)
Receiver enable time
tPZL(2), Driver disabled See Figure 6-8 4 10 µs
tPZH(2)

8 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

5.10 Typical Characteristics

6 5
5.5 VOH (VCC=5V) 4.8 VCC = 5 V

Driver Differential Output Voltage (V)

VOL (VCC=5V)
5 4.6
Driver Output Voltage (V)

4.5 4.4
4 4.2
4
3.5
3.8
3
3.6
2.5
3.4
2 3.2
1.5 3
1 2.8
0.5 2.6
0 2.4
0 10 20 30 40 50 60 70 80 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80
Driver Output Current (mA) D001
Driver Output Current (mA) D002

D001_driver_vout_iout.grf D002_driver_vdiff.grf

DE = VCC TA = 25°C DE = VCC D=0V TA = 25°C

Figure 5-1. Driver Output voltage vs Driver Output Current Figure 5-2. Driver Differential Output voltage vs Driver Output
Current
66 350
Fall time (VCC=5V)
63
345 Rise time (VCC=5V)

Driver Rise and Fall Time (ns)

60
Driver Output Current (mA)

57 340

54 335
51
330
48
45 325
42 320
39
315
36
33 310
3 3.25 3.5 3.75 4 4.25 4.5 4.75 5 5.25 5.5 -40 -20 0 20 40 60 80 100 120 140
Vcc (V) D003
Temperature (qC) D004

D003_Iout_vcc.grf D004_rise_fall.grf

RL = 54 Ω DE = VCC D = VCC RL = 54 Ω CL = 50 pF
TA = 25°C spacer
Figure 5-3. Driver Output Current vs Supply Voltage Figure 5-4. Driver Rise or Fall Time vs Temperature (THVD1400)
320 75
tPHL (ns) VCC=5V VCC=5V
315 tPLH (ns) VCC=5V
70
310
Propgation Delay (ns)

Supply Current (mA)

305 65
300

295 60

290
55
285

280 50
-40 -20 0 20 40 60 80 100 120 140 0 50 100 150 200 250 300 350 400 450 500
Temperature (qC) D005
Signaling Rate (kbps) D006

D005_prop_delay.grf D006_Icc_datarate.grf

RL = 54 Ω CL = 50 pF RL = 54 Ω TA = 25 °C
Figure 5-5. Driver Propagation Delay vs Temperature Figure 5-6. Supply Current vs Signal Rate (THVD1400)
(THVD1400)

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 9

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

5.10 Typical Characteristics (continued)

11 21
Rise Time (V CC = 5 V ) tPHL (VCC = 5 V)
10.5 Fall Time (V CC = 5 V) 20 tPLH (VCC = 5 V)
10
Driver Rise Fall Time (ns)

19

Propagation Delay (ns)

9.5
9 18

8.5 17
8 16
7.5
15
7
6.5 14

6 13
-40 -20 0 20 40 60 80 100 120 140 -40 -20 0 20 40 60 80 100 120 140
Temperature (C) Temperature (C)

RL = 54 Ω CL = 50 pF RL = 54 Ω CL = 50 pF
Figure 5-7. Driver Rise and Fall Time vs Temperature Figure 5-8. Driver Propagation Delay vs Temperature
(THVD1420) (THVD1420)
65
VCC = 5 V
Supply Current (mA)

60

55

50
0 2000 4000 6000 8000 10000 12000
Signaling Rate (kbps)

RL = 54 Ω TA = 25 °C
Figure 5-9. Supply Current vs Signal Rate (THVD1420)

10 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

6 Parameter Measurement Information

Vcc 375 Ÿ

DE
A
D Vtest
0V or Vcc VOD RL

375 Ÿ

Figure 6-1. Measurement of Driver Differential Output Voltage With Common-Mode Load
A
VA
A RL/2 B
D VB
0V or Vcc VOD
RL/2 VOC(PP)
B VOC ûVOC(SS)
CL
VOC

Figure 6-2. Measurement of Driver Differential and Common-Mode Output With RS-485 Load
Vcc
Vcc
VI 50%
DE 0V
A tPHL
D RL= tPLH
VOD 54 Ÿ CL= 50 pF ~2 V
Input 90%
VI 50 Ÿ B 50%
Generator
VOD 10%
tr tf ~ ±2V

Figure 6-3. Measurement of Driver Differential Output Rise and Fall Times and Propagation Delays
A Vcc
D S1 VO
VI 50%
B 0V
DE RL = tPZH
CL = 110 Ÿ
Input VOH
50 Ÿ 50 pF 90%
Generator VI
50%
VO
~
~ 0V
tPHZ

Figure 6-4. Measurement of Driver Enable and Disable Times With Active High Output and Pull-Down
Load
Vcc
Vcc
RL= 110 Ÿ 50%
VI
A 0V
S1
VO tPZL
D B tPLZ
§ Vcc
VO
DE CL=
Input 50 pF 50 % 10%
Generator VI VOL
50 Ÿ

Figure 6-5. Measurement of Driver Enable and Disable Times With Active Low Output and Pull-up Load

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 11

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com
3V
VI 50 %
A 0V
R VO tPLH tPHL
Input
Generator VI 50 Ÿ 1.5V VOH
B CL=15 pF 90%
50%
RE VOD
0V 10 %
tr tf VOL

Figure 6-6. Measurement of Receiver Output Rise and Fall Times and Propagation Delays
Vcc
Vcc Vcc
VI 50 %
DE 0V
A 1 kŸ tPZH(1) tPHZ
D R VO D at Vcc
0V or Vcc S1 VOH
90 % S1 to GND
VO 50 %
B CL=15 pF
RE § 0V
tPZL(1)
tPLZ
Input
50 Ÿ VCC D at 0V
Generator VI S1 to Vcc
VO 50 %
10 %
VOL

Figure 6-7. Measurement of Receiver Enable/Disable Times With Driver Enabled

Vcc
Vcc VI 50%
0V
A 1 NŸ tPZH(2)
V or 1.5V R VO
S1 VOH A at 1.5 V
1.5 V or 0V 50% B at 0 V
B CL=15 pF VO S1 to GND
RE § 0V
tPZL(2)
Input VCC A at 0V
Generator VI 50 Ÿ
VO 50% B at 1.5V
S1 to VCC
VOL

Figure 6-8. Measurement of Receiver Enable Times With Driver Disabled

12 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

7 Detailed Description
7.1 Overview
The THVD1400 is a low-power, half-duplex RS-485 transceiver suitable for data transmission up to 500 kbps.
The THVD1420 is a low-power, half-duplex RS-485 transceiver suitable for data transmission up to 12 Mbps.
7.2 Functional Block Diagrams
VCC

R
RE A
DE B

GND

7.3 Feature Description

Internal ESD protection circuits protect the transceiver against Electrostatic Discharges (ESD) according to IEC
61000-4-2 of up to ±12 kV (Contact Discharge), ±15 kV (Air Gap Discharge) and against electrical fast transients
(EFT) according to IEC 61000-4-4 of up to ±4 kV.
7.4 Device Functional Modes
When the driver enable pin, DE, is logic high, the differential outputs A and B follow the logic states at data input
D. A logic high at D causes A to turn high and B to turn low. In this case, the differential output voltage defined
as VOD = VA – VB is positive. When D is low, the output states reverse, B turns high, A becomes low, and VOD is
negative.
When DE is low, both outputs turn high-impedance. In this condition, the logic state at D is irrelevant. The DE
pin has an internal pull-down resistor to ground; thus, when left open, the driver is disabled (high-impedance) by
default. The D pin has an internal pull-up resistor to VCC, thus, when left open while the driver is enabled, output
A turns high and B turns low.
Table 7-1. Driver Function Table
INPUT ENABLE OUTPUTS
FUNCTION
D DE A B
H H H L Actively drive bus high
L H L H Actively drive bus low
X L Z Z Driver disabled
X OPEN Z Z Driver disabled by default
OPEN H H L Actively drive bus high by default

When the receiver enable pin, RE, is logic low, the receiver is enabled. When the differential input voltage
defined as VID = VA – VB is positive and higher than the positive input threshold, VIT+, the receiver output, R,
turns high. When VID is negative and lower than the negative input threshold, VIT-, the receiver output, R, turns
low. If VID is between VIT+ and VIT- the output is indeterminate.
When RE is logic high or left open, the receiver output is high-impedance and the magnitude and polarity of VID
are irrelevant. Internal biasing of the receiver inputs causes the output to go failsafe-high when the transceiver is
disconnected from the bus (open-circuit), the bus lines are shorted (short-circuit), or the bus is not actively driven
(idle bus).

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 13

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

Table 7-2. Receiver Function Table

DIFFERENTIAL INPUT ENABLE OUTPUT
FUNCTION
VID = VA – VB RE R
VIT+ < VID L H Receive valid bus high
VIT- < VID < VIT+ L ? Indeterminate bus state
VID < VIT- L L Receive valid bus low
X H Z Receiver disabled
X OPEN Z Receiver disabled by default
Open-circuit bus L H Fail-safe high output
Short-circuit bus L H Fail-safe high output
Idle (terminated) bus L H Fail-safe high output

14 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

8 Application Information Disclaimer

Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.

8.1 Application Information

The THVD1400 is a half-duplex RS-485 transceiver commonly used for asynchronous data transmissions. The
driver and receiver enable pins allow for the configuration of different operating modes.
8.2 Typical Application
An RS-485 bus consists of multiple transceivers connecting in parallel to a bus cable. To eliminate line
reflections, each cable end is terminated with a termination resistor, RT, whose value matches the characteristic
impedance, Z0, of the cable. This method, known as parallel termination, allows for higher data rates over longer
cable length.

R R R R
A A
RE RE
RT RT
B B
DE DE
D D D D
A B A B

R R
D D

R RE DE D R RE DE D

Figure 8-1. Typical RS-485 Network With Half-Duplex Transceivers

8.2.1 Design Requirements

RS-485 is a robust electrical standard suitable for long-distance networking that may be used in a wide range of
applications with varying requirements, such as distance, data rate, and number of nodes.
8.2.1.1 Data Rate and Bus Length
There is an inverse relationship between data rate and cable length, which means the higher the data rate, the
shorter the cable length; and conversely, the lower the data rate, the longer the cable length. While most RS-485
systems use data rates between 10 kbps and 100 kbps, some applications require data rates up to 300 kbps at
distances of 4000 feet and longer. Longer distances are possible by allowing for small signal jitter of up to 5 or
10%.

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 15

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

8.2.1.2 Stub Length

When connecting a node to the bus, the distance between the transceiver inputs and the cable trunk, known as
the stub, should be as short as possible. Stubs present a non-terminated piece of bus line which can introduce
reflections as the length of the stub increases. As a general guideline, the electrical length, or round-trip delay, of
a stub should be less than one-tenth of the rise time of the driver, thus giving a maximum physical stub length as
shown in Equation 1.

L(STUB) ≤ 0.1 × tr × v × c (1)

where
• tr is the 10/90 rise time of the driver
• c is the speed of light (3 × 108 m/s)
• v is the signal velocity of the cable or trace as a factor of c
8.2.1.3 Bus Loading
The RS-485 standard specifies that a compliant driver must be able to driver 32 unit loads (UL), where 1
unit load represents a load impedance of approximately 12 kΩ. Because the THVD1400 consists of 1/8 UL
transceivers, connecting up to 256 receivers to the bus is possible.
8.2.1.4 Receiver Failsafe
The differential receivers of the THVD1400 are failsafe to invalid bus states caused by the following:
• Open bus conditions, such as a disconnected connector
• Shorted bus conditions, such as cable damage shorting the twisted-pair together
• Idle bus conditions that occur when no driver on the bus is actively driving
In any of these cases, the differential receiver outputs a failsafe logic high state so that the output of the receiver
is not indeterminate.
Receiver failsafe is accomplished by offsetting the receiver thresholds such that the input indeterminate range
does not include zero volts differential. To comply with the RS-422 and RS-485 standards, the receiver output
must output a high when the differential input VID is more positive than 200 mV, and must output a low when
VID is more negative than –200 mV. The receiver parameters which determine the failsafe performance are VIT+,
VIT–, and VHYS (the separation between VIT+ and VIT–). As shown in the Receiver Function Table, differential
signals more negative than –200 mV always causes a low receiver output, and differential signals more positive
than 200 mV always causes a high receiver output.
When the differential input signal is close to zero, it is still above the VIT+ threshold, and the receiver output is
high. Only when the differential input is more than VHYS below VIT+ does the receiver output transition to a low
state. Therefore, the noise immunity of the receiver inputs during a bus fault conditions includes the receiver
hysteresis value, VHYS, as well as the value of VIT+.

16 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

8.2.1.5 Transient Protection

The bus pins of the THVD1400 transceiver family include on-chip ESD protection against ±16-kV HBM and
±12-kV IEC 61000-4-2 contact discharge. The International Electrotechnical Commission (IEC) ESD test is far
more severe than the HBM ESD test. The 50% higher charge capacitance, C(S), and 78% lower discharge
resistance, R(D), of the IEC model produce significantly higher discharge currents than the HBM model.
R(C) R(D)
40
50 M 330 Ω 35
30 10-kV IEC

Current (A)
(1 M) (1.5 kΩ)
25
High-Voltage 150 pF Device
C(S) Under 20
Pulse (100 pF)
Generator Test 15
10
10-kV HBM
5
0
0 50 100 150 200 250 300
Time (ns)

Figure 8-2. HBM and IEC ESD Models and Currents in Comparison (HBM Values in Parenthesis)

The on-chip implementation of IEC ESD protection significantly increases the robustness of equipment.
Common discharge events occur because of human contact with connectors and cables. Designers may choose
to implement protection against longer duration transients, typically referred to as surge transients.
EFTs are generally caused by relay-contact bounce or the interruption of inductive loads. Surge transients
often result from lightning strikes (direct strike or an indirect strike which induce voltages and currents), or
the switching of power systems, including load changes and short circuit switching. These transients are often
encountered in industrial environments, such as factory automation and power-grid systems.
Figure 8-3 compares the pulse-power of the EFT and surge transients with the power caused by an IEC ESD
transient. The left hand diagram shows the relative pulse-power for a 0.5-kV surge transient and 4-kV EFT
transient, both of which dwarf the 10-kV ESD transient visible in the lower-left corner. 500-V surge transients are
representative of events that may occur in factory environments in industrial and process automation.
The right hand diagram shows the pulse-power of a 6-kV surge transient, relative to the same 0.5-kV surge
transient. 6-kV surge transients are most likely to occur in power generation and power-grid systems.
3.0
2.8
2.6 6-kV Surge
2.4
22 2.2
Pulse Power (MW)

20 2.0
18 0.5-kV Surge 1.8
16 1.6
Pulse Power (kW)

14 1.4
12 1.2
4-kV EFT
10 1.0
8 0.8
6 0.6
4 0.4
2 10-kV ESD 0.2 0.5-kV Surge
0 0
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
Time (µs) Time (µs)

Figure 8-3. Power Comparison of ESD, EFT, and Surge Transients

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 17

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

In the event of surge transients, high-energy content is characterized by long pulse duration and slow decaying
pulse power. The electrical energy of a transient that is dumped into the internal protection cells of a transceiver
is converted into thermal energy, which heats and destroys the protection cells, thus destroying the transceiver.
Figure 8-4 shows the large differences in transient energies for single ESD, EFT, surge transients, and an EFT
pulse train that is commonly applied during compliance testing.
1000

100

Surge
10

1
EFT Pulse Train
Pulse Energy (J)

0.1

0.01

EFT
10-3

10-4

ESD
10-5

10-6
0.5 1 2 4 6 8 10 15
Peak Pulse Voltage (kV)

Figure 8-4. Comparison of Transient Energies

18 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

8.2.2 Detailed Design Procedure

In order to protect bus nodes against high-energy transients, the implementation of external transient protection
devices is necessary. Figure 8-5 suggests a protection circuit against 1 kV surge (IEC 61000-4-5) transients.
Table 8-1 shows the associated bill of materials.

5V
100nF 100nF

10k VCC
R1
R
RxD
MCU/ RE A TVS
UART
DE B
DIR
D
TxD
R2
10k GND

Figure 8-5. Transient Protection Against Surge Transients for Half-Duplex Devices

Table 8-1. Bill of Materials

DEVICE FUNCTION ORDER NUMBER MANUFACTURER
XCVR RS-485 transceiver THVD1400 TI
R1
10-Ω, pulse-proof thick-film resistor CRCW0603010RJNEAHP Vishay
R2
TVS Bidirectional 400-W transient suppressor CDSOT23-SM712 Bourns

8.2.3 Application Curves

Figure 8-6. THVD1400 waveforms at 500 kbps, VCC = 5V

9 Power Supply Recommendations

To ensure reliable operation at all data rates and supply voltages, each supply should be decoupled with a 100
nF ceramic capacitor located as close to the supply pins as possible. This helps to reduce supply voltage ripple
present on the outputs of switched-mode power supplies and also helps to compensate for the resistance and
inductance of the PCB power planes.
Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 19
Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

10 Layout
10.1 Layout Guidelines
Robust and reliable bus node design often requires the use of external transient protection devices in order
to protect against surge transients that may occur in industrial environments. Since these transients have a
wide frequency bandwidth (from approximately 3 MHz to 300 MHz), high-frequency layout techniques should be
applied during PCB design.
1. Place the protection circuitry close to the bus connector to prevent noise transients from propagating across
the board.
2. Use VCC and ground planes to provide low inductance. Note that high-frequency currents tend to follow the
path of least impedance and not the path of least resistance.
3. Design the protection components into the direction of the signal path. Do not force the transient currents to
divert from the signal path to reach the protection device.
4. Apply 100-nF to 220-nF decoupling capacitors as close as possible to the VCC pins of transceiver, UART
and/or controller ICs on the board.
5. Use at least two vias for VCC and ground connections of decoupling capacitors and protection devices to
minimize effective via inductance.
6. Use 1-kΩ to 10-kΩ pull-up and pull-down resistors for enable lines to limit noise currents in these lines during
transient events.
7. Insert pulse-proof resistors into the A and B bus lines if the TVS clamping voltage is higher than the specified
maximum voltage of the transceiver bus pins. These resistors limit the residual clamping current into the
transceiver and prevent it from latching up.
8. While pure TVS protection is sufficient for surge transients up to 1 kV, higher transients require metal-oxide
varistors (MOVs) which reduce the transients to a few hundred volts of clamping voltage, and transient
blocking units (TBUs) that limit transient current to less than 1 mA.
10.2 Layout Example
5
Via to ground
C 4 Via to VCC
R

6 R
R 1 JMP
MCU 7 R
R 5
TVS
6 R
5

Figure 10-1. Layout Example for SOIC package

20 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 THVD1400, THVD1420
www.ti.com SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021

Figure 10-2. Layout Example for Co-layout of SOIC (D) and SOT (DRL)

Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 21

Product Folder Links: THVD1400 THVD1420
THVD1400, THVD1420
SLLSF78B – DECEMBER 2020 – REVISED OCTOBER 2021 www.ti.com

11 Device and Documentation Support

11.1 Device Support
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.

11.6 Glossary
TI Glossary This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

22 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated

Product Folder Links: THVD1400 THVD1420

 PACKAGE OPTION ADDENDUM

www.ti.com 5-Aug-2023

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

THVD1400DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 1400 Samples

THVD1400DRLR ACTIVE SOT-5X3 DRL 8 4000 RoHS & Green Call TI | SN Level-1-260C-UNLIM -40 to 125 T400 Samples

THVD1420DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 1420 Samples

THVD1420DRLR ACTIVE SOT-5X3 DRL 8 4000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 T420 Samples

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 5-Aug-2023

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 3-Jun-2023

TAPE AND REEL INFORMATION

REEL DIMENSIONS TAPE DIMENSIONS

K0 P1

B0 W
Reel
Diameter
Cavity A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
W Overall width of the carrier tape
P1 Pitch between successive cavity centers

Reel Width (W1)

QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

Sprocket Holes

Q1 Q2 Q1 Q2

Q3 Q4 Q3 Q4 User Direction of Feed

Pocket Quadrants

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
THVD1400DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
THVD1400DRLR SOT-5X3 DRL 8 4000 180.0 8.4 2.75 1.9 0.8 4.0 8.0 Q3
THVD1420DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
THVD1420DRLR SOT-5X3 DRL 8 4000 180.0 8.4 2.75 1.9 0.8 4.0 8.0 Q3

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 3-Jun-2023

TAPE AND REEL BOX DIMENSIONS

Width (mm)
H
W

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
THVD1400DR SOIC D 8 2500 356.0 356.0 35.0
THVD1400DRLR SOT-5X3 DRL 8 4000 210.0 185.0 35.0
THVD1420DR SOIC D 8 2500 356.0 356.0 35.0
THVD1420DRLR SOT-5X3 DRL 8 4000 210.0 185.0 35.0

Pack Materials-Page 2
 PACKAGE OUTLINE
D0008A SCALE 2.800
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT

SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A PIN 1 ID AREA
6X .050
[1.27]
8
1

.189-.197 2X
[4.81-5.00] .150
NOTE 3 [3.81]

4X (0 -15 )

4
5
8X .012-.020
B .150-.157 [0.31-0.51]
.069 MAX
[3.81-3.98] .010 [0.25] C A B [1.75]
NOTE 4

.005-.010 TYP
[0.13-0.25]

4X (0 -15 )

SEE DETAIL A
.010
[0.25]

.004-.010
0 -8 [0.11-0.25]
.016-.050
[0.41-1.27] DETAIL A
(.041) TYPICAL
[1.04]

4214825/C 02/2019

NOTES:

1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.

www.ti.com
 EXAMPLE BOARD LAYOUT
D0008A SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT

8X (.061 )
[1.55]
SYMM SEE
DETAILS
1
8

8X (.024)
[0.6] SYMM

(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE:8X

SOLDER MASK SOLDER MASK

METAL METAL UNDER
OPENING OPENING SOLDER MASK

EXPOSED
METAL EXPOSED
METAL
.0028 MAX .0028 MIN
[0.07] [0.07]
ALL AROUND ALL AROUND

NON SOLDER MASK SOLDER MASK

DEFINED DEFINED

SOLDER MASK DETAILS

4214825/C 02/2019

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

www.ti.com
 EXAMPLE STENCIL DESIGN
D0008A SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT

8X (.061 )
[1.55] SYMM

1
8

8X (.024)
[0.6] SYMM

(R.002 ) TYP
5 [0.05]
4
6X (.050 )
[1.27]
(.213)
[5.4]

SOLDER PASTE EXAMPLE

BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X

4214825/C 02/2019

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.

www.ti.com
 PACKAGE OUTLINE
DRL0008A SCALE 8.000
SOT-5X3 - 0.6 mm max height
PLASTIC SMALL OUTLINE

1.3
B
1.1
A
PIN 1
ID AREA

1
8

6X 0.5

2.2
2X 1.5
2.0
NOTE 3

5
4
0.27
8X
0.17
0.1 C A B 1.7 0.05
1.5 0.00
0.05

0.6 MAX C

SEATING PLANE
0.18
0.08 0.05 C
SYMM
0.4
8X
0.2

SYMM

4224486/E 12/2021
NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, interlead flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4.Reference JEDEC Registration MO-293, Variation UDAD

www.ti.com
 EXAMPLE BOARD LAYOUT
DRL0008A SOT-5X3 - 0.6 mm max height
PLASTIC SMALL OUTLINE

8X (0.67)
SYMM

8X (0.3) 1 8

SYMM

6X (0.5)

5
4

(R0.05) TYP
(1.48)

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE:30X

0.05 MAX 0.05 MIN

AROUND AROUND

EXPOSED EXPOSED
METAL METAL

SOLDER MASK METAL METAL UNDER SOLDER MASK

OPENING SOLDER MASK OPENING
NON SOLDER MASK SOLDER MASK
DEFINED DEFINED
(PREFERRED)

SOLDERMASK DETAILS

4224486/E 12/2021

NOTES: (continued)

5. Publication IPC-7351 may have alternate designs.

6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
7. Land pattern design aligns to IPC-610, Bottom Termination Component (BTC) solder joint inspection criteria.

www.ti.com
 EXAMPLE STENCIL DESIGN
DRL0008A SOT-5X3 - 0.6 mm max height
PLASTIC SMALL OUTLINE

8X (0.67)
SYMM

8X (0.3) 1 8

SYMM

6X (0.5)

5
4

(R0.05) TYP
(1.48)

SOLDER PASTE EXAMPLE

BASED ON 0.1 mm THICK STENCIL
SCALE:30X

4224486/E 12/2021

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.

www.ti.com
 IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated