Quick Start Guide

4-inch Visible Light Sysytem

www.esslsecurity.com
Overview
Flash
Camera& Palm Collector

Microphone

4-inch Touchscreen
Speaker

Reset
Doorbell Button

Card Reading Area

USB

Alarm

AL+ AL-
12V NO GND Auxiliary
Power in input
GND Lock COM AUX
NC BUT Exit Button
GND SEN Sensor
TX+
485B BELL+
TX- RS485 Bell
Ethernet 485A BELL-
RX+
Wiegandin IWD0 GND
RX-
IWD1 GND
+12V WD0 Wiegand
GND WD1 Out

1
Installation Environment
Please refer to the following recommendations for installation.

INSTALL INDOORS AVOID INSTALLATION AVOID DIRECT AVOID USE OF ANY

ONLY NEAR SUNLIGHT HEAT SOURCE
GLASS WINDOWS AND EXPOSURE NEAR THE DEVICE

Recommended Palm Gestures

KEEP EFFECTIVE KEEP SPACES DO NOT KEEP DO NOT KEEP DO NOT KEEP
DISTANCE OF BETWEEN YOUR FINGERS PALM OUTSIDE YOUR FINGERS
30-50 cm YOUR FINGERS CLOSE COLLECTION AREA FOLD/CURLED

Note:
1. Place your palm within 30-50 cm of the device.
2. Place your palm in the palm collection area, such that the palm is placed parallel
to the device.
3. Make sure to keep space between your fingers.

Recommended Standing Position

KEEP EFFECTIVE
DISTANCE OF
0.3-2m

2
Device Installation
1 2 3
①
Fixing Hole Fixing Hole Fixing Hole

1.5m recommended height from the ground and can be

adjusted according to the staff height.

Mounting Positioning Sticker

(Only for your reference)
Instruction on using Mounting Positioning Sticker:

Before fastening the device, please stick this Mounting

Positioning Sticker onto where you want to install the device,
and then drill holes and lay cables according to the symbols on
the sticker.

Fixing Hole Fixing Hole

Wiring Hole
Fixing Hole

1.5m Fixing Hole

Fixing Hole Fixing Hole Fixing Hole

① Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper. Fix the back plate on the wall using wall mounting
screws.
② Attach the device to the back plate.
③ Fasten the device to the back plate with a security screw.

Standalone Installation
Alarm Smoke
Detector

Door Sensor

Exit Button

PC
Card Lock TCP/IP
Reader
Power Connection

12V 12V DC
GND GND

Recommended power supply

1) 12V ± 10%, at least 3000mA.
2) To share the power with other devices, use a power supply with higher current
ratings.

Ethernet Connection

TX+
TX-
1
2
3

RX+ 4
5
6
RJ 45
RX- 7
8

IP address: 192.168.1.130
Subnet mask: 255.255.255.0

Default IP address: 192.168.1.201

Subnet mask: 255.255.255.0

Click [COMM.] > [Ethernet] > [IP Address] , input the IP address and click [OK].
Note: In LAN, IP addresses of the server (PC) and the device must be in the same
network segment when connecting to BioAccess IVS software.
 Lock Relay Connection
The system supports both Normally Opened Lock and Normally Closed Lock.
The NO Lock (normally opened when powered) is connected with 'NO1' and
'COM' terminals, and the NC Lock (normally closed when powered) is connected
with 'NC1' and 'COM' terminals. The power can be shared with the lock or can be
used separately for the lock, as shown in the example with NC Lock below:
1) Device not sharing power with the lock 2) Device sharing power with the lock

+12V +12V
GND GND
DC12V DC12V
AL+ AL+
NO NO
COM COM
DC12V NC NC
GND GND
485B 485B
485A 485A
IWD0 IWD0
FR107 FR107
IWD1 IWD1
Normally Closed Lock +12V Normally Closed Lock +12V
GND GND

Door Sensor, Exit Button & Alarm Connection

Alarm's Power Alarm
Switch
+ + -
-

AL+ AL- - +
NO GND -
+

COM AUX
Smoke Detector
NC BUT
GND SEN
485B BELL+ Door
485A BELL- Sensor
IWD0 GND
IWD1 GND
Exit Button
 Wiegand Reader Connection
Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last
two pins are used by the Access Controller, as shown in the following figure. It sends the
credentials to the device via wiegand communication.

WD0
WD1 Access Controller

WD0
IWD0
WD1
IWD1 +12V
+12V GND
GND
Wiegand Reader

RS485 Connection
The RS485 lets user connect to multiple readers to the device. RS485 can be connected
to the terminal, as shown in the figure below.

AL+
NO
COM
NC
GND
GND
485-
485B
485+
485A
IWD0
IWD1 RS485 Reader
User Registration
When there is no super administrator set in the device, click on to enter the menu.
Add a new user and set User Role to Super Admin, then the system will request for the
administrator’s verification before entering the menu. It is recommended to register a
super administrator initially for security purposes.
Method 1: Register on the device
Click on > [User Mgt.] > [New User] to register a new user. The options include
entering the user ID and Name, setting User Role, registering Palm, Face, Card
Number, Password and adding User Photo.
2020-07-22 14:31 Main Menu User Mgt.

New User


User Mgt. User Role COMM. System All Users

Display Style

Personalize Data Mgt. Access USB

Control Manager

Attendance Autotest System Info

2020-07-22 Thursday Search

Welcome


New User Palm Registration Enroll Face

User ID 1

Name Mike

User Role Normal User

Palm 1

Face 1

Card Number 1

Password *****

User Photo 1

Access Control Role

Enrolled Successfully Enrolled Successfully

Ethernet and Cloud Server Settings
Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP
communication of the device is successful, the icon will be displayed in the
upper right corner of the standby interface.
Click on > [COMM.] > [Cloud Server Setting] to set the server address and server
port, that is, the IP address and port number of the server after the software is
installed. If the device communicates with the server successfully, the icon will be
displayed in the upper right corner of the standby interface.

Main Menu Ethernet Cloud Server Setting

IP Address 192.168.163.200 Server mode ADMS


User Mgt. User Role COMM. System Subnet Mask 255.255.255.0 Enable Domain Name

Gateway 192.168.163.1 Server Address 0.0.0.0

Personalize Data Mgt. Access USB DNS 0.0.0.0 Server Port 8081
Control Manager

TCP COMM. Port 4970 Enable Proxy Server

Attendance Autotest System Info

Search DHCP HTTPS

Display in Status Bar

Note:
While pairing the device with ZKBioAccess IVS software. Make sure that the option
Enable Domain Name is disabled and the correct server address and port are entered.
Server Address: Set as the IP address of the ZKBioAccess IVS server.
Server Port: Set as the service port of ZKBioAccess IVS(the default is 8088).
Access Control Setting
Click on > [Access Control] to enter the access control management interface and
set relevant parameters of access control.

Main Menu Access Control Access Control Options

Access Control Options Gate Control Mode

User Mgt. User Role COMM. System Time Rule setting Verification Mode Password/Face/Palm

Holidays Door available time period 1

Personalize Data Mgt. Access USB


Combined Verification Normal open time period None
Control Manager

Anti-passback Setup Master Device In

Attendance Autotest System Info Duress Options Out

Search Slave Device

Auxiliary input configuration

Verify mode by RS485 Card Only

Speaker Alarm

Reset Access Setting

Attendance Record
Click on > [Attendance Search] > [Event Logs] to enter the logs query interface,
input the user ID and select the time range, the corresponding event logs will be dis-
played.
Main Menu Attendance Search Personal Record Search

Date User ID Time

Event Logs Number of Records:04
03-03
4 11:25
User Mgt. User Role COMM. System Attendance Photo 2 11:25 11:22
3 11:25
Blocklist ATT Photo 03-04 Number of Records:04
1 11:29
Personalize Data Mgt. Access USB 3 11:29 11:21
Control Manager 2 11:28
4 11:26
03-05 Number of Records:04
1 11:27
Attendance Autotest System Info


Search 4
3
2
11:27
11:27
11:27
#24, Shambavi Building, 23rd Main, Marenahalli,JP Nagar 2nd Phase,
Bengaluru - 560078
Phone : 91-8026090500 | Email : [email protected]
www.esslsecurity.com