CE6000 SERIES

CUTTING PLOTTER

SETUP MANUAL
MANUAL NO.CE6000-UM-8M4

Preface
Thank you for choosing this product. Carefully keep this manual in a handy location for quick reference as necessity
prior to use to ensure safe and correct use and also to thoroughly understand the functions and operate them
effectively.

Prior to use
Be sure to read the attached "TO ENSURE SAFE AND CORRECT USE" prior to use. Otherwise, it may cause an
unexpected accident or fire.

Notes on this Manual

(1) No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
without the prior written permission of Graphtec Corporation.
(2) The product specifications and other information in this manual are subject to change without notice.
(3) While every effort has been made to provide complete and accurate information, please contact your sales
representative or nearest Graphtec vendor if you find any unclear or erroneous information or wish to make other
comments or suggestions.
(4) Notwithstanding the stipulations in the preceding paragraph, Graphtec Corporation assumes no liability for damages
resulting from either the use of the information contained herein or the use of the product.

Registered Trademarks
All names of companies, brands, logotypes, and products appearing in this manual are the trademarks or registered
trademarks of their respective companies.

Copyright
This User's Manual is copyrighted by Graphtec Corporation.

Roles of each manual

•Setup Manual (this manual) Read it to understand Displaying method for User's Manual, Method for connecting
this Cutting Plotter with the PC, Installing method for controller driver software, and to
prepare for the operation.

•User's Manual (PDF data) Read it to thoroughly understand the functions.

• Cutting Plotter Controller ManualRead
(PDF data)
it to run the software "Cutting Plotter Controller" for operation of this Cutting
Plotter through your PC.

621588810
 Before starting the Setup
Make the following preparations before starting Setup.
• For
Check that all of the items included in the package. (Please see the User's Manual (PDF).)
the Parts Names, please see the User's Manual (PDF).
• User's Manual
Assemble this Cutting Plotter, and set up it. For the assembling procedures, see either Manual attached to the Stand or
(PDF).
• To use the Cutting Master 4, previously install the Design application (Adobe Illustrator or CorelDRAW) that is used.
For the latest supported version, please visit our website.

• When there are virus detection program or system resident program, terminate them beforehand.
• Upon installation, be sure to log into Windows using an account with administrator privileges on your computer.
CAUTION
Usage of the software
Each of the Cutting Plotter Controller/Graphtec Studio software is engaged in various settings on the Cutting Plotter. Do not use them at
the same time.

Flow of setup
Setting up the Plotter main unit
The cutter blade can replaced depending on the material or thickness of the
1. Attaching a Tool media.
P.03

2. Loading Media (Paper or Marking Film) Fix the media to the Plotter. P.04

3. Aligning the Push Rollers Adjust the position of the push roller. P.09

4. About the Initial Setup screen Select "Display Language" and "Length Unit". P.10

5. Set the media type into the Plotter Set the media type to the Cutting Plotter, depending on the set media. P.10

Adjust the protruded cutter edge length and the cutting Force depending on the material
6 Tool adjustment and test cutting and thickness of the media. Make test cutting for the set media to adjust the best condition.
P.11

Installing the Software

• Setup in a Windows operating environment
For each software, install them using the Installer housed in the attached
Launching the Start menu DVD-ROM.
P.14

A. Install CE6000Plus Software

Once Cutting Plotter Controller is installed, you can control main functions of
Installing the Cutting Plotter Controller P.16
the Cutting Plotte through the PC.
Installing the Driver software The Driver software controls the Plotter and makes plotting according to the
(Cutting Plotter Driver) P.16
data created by the PC.

• To connect using the USB Turn on the power source of Plotter in the middle of installing, and connect the USB cable. P.17

Install the software as necessity.

Software enabling cutting data to be created through simple commands.
B. Setup the Graphtec Pro Studio Create designs and edit characters/shapes using this software.
P.18

Plug-in driver that enables simple cutting through direct operation from within
C. Setup the Cutting Master 4 Adobe Illustrator and CorelDRAW.
P.18

D. Install the User's Manual Installs the User's Manual. P.18

• Setup in a Macintosh operating environment

Plug-in driver that enables simple cutting through direct operation from within
A. Setup the Cutting Master 4 Adobe Illustrator.
P.19

Software enabling cutting data to be created through simple commands.

B. Setup the Graphtec Studio Create designs and edit characters/shapes using this software.
P.19

2
 Setting up the Plotter main unit
1. Attaching a Tool
Attach a tool (cutter plunger, plotter pen) to the plotter.

Attaching a Tool
When mounting the tool in the tool holder, please note the following.

• firmly.
Push the tool all the way into the holder until its flange contacts the upper part of the holder and then tighten the screw

• isTomoving.
prevent injury, avoid absolutely touching the tool immediately after the cutting plotter is turned on or whenever the tool

For details, see “Attaching a Tool” on in User’s Manual.

It is explained here using cutter plunger as an example.

CAUTION
When pushing the tool holder with your fingers, the blade tip may be protruding. Take care not to cut your fingers.
Supplement
• When using with half cutting and plotter pen, set the seal in Tool Holder 1 (backward), and when using cutting out (perforated cut), set
the seal in Tool Holder 2 (forward).
• Cutting out means that the media is cut out completely.
• Half cutting means that only the marking film is cut out, leaving the backing sheet uncut.

1 Loosen the tool holder screw.

Bracket to hold tool Tool holder

Tool holder

Bracket to hold tool

Top

2 While pushing up the tool holder, push until its flange completely touches
the upper part of the holder. Supplement
Bracket to When using with half cutting and plotter pen,
Tool holder
hold tool Flange set the seal in Tool Holder 1 (backward), and
when using cutting out (perforated cut), set the
seal in Tool Holder 2 (forward).

Tool holder 1
(Backward : Half cutting/Plotting Pen)

Tool holder 2
(Forward : Using
cutting)

3
3 Make sure that the tool bracket is engaged on the tool's flange, and then tighten the screw.
Bracket to hold tool Flange

Removing the tool

When removing the tool, turn it counterclockwise to remove the tool.

2. Loading Media (Paper or Marking Film)

Both roll media and sheet media can be used with the CE6000.
Load the media according to the instructions given for each type. Use the grit roller on the right side of the media (looking
from the front) as a guide when setting it in the media sensor. Afterwards, adjust the push roller so that it's lined up with the
side of the media.
For details, see User's Manual (PDF).

Loading Roll Media

1 Lower the media set lever to raise the push rollers.

Push roller Media set

lever Supplement
Media sensor
For more information about the position of the
push roller, see "Adjust the Push Roller".

2 Set the roll media on top of the stock shaft, and then insert the roll media into the stopper. Once it's set, tighten the
stopper's screws.

Stopper

4
 3 Push the tip of the roll media forward from the back of the CE6000.
When using the roll media tray
Make sure to pull it so that there is no slackening across the roll media's
route. Put the roll media on the roll media tray and
then push the tip of the roll media forward from
the back of the machine.

4 Press the media stopper to engage it, and then pull the leading edge
Media stopper
out of the front of the plotter, making sure that it completely covers the
This stops the stock shaft from spinning when
media sensor.
setting in media. It is also utilized when pulling
roll media straight out.
Media sensors

Media stopper

Slide the Supplement

media
stopper When actually cutting, please release the lock
from the media stopper (while pulling to the
exterior, slide it forward).

5 Position the media and the push rollers to correspond with the width of
the media.

When using the model with 2 push rollers

The push rollers push down on either side of the media. Use the grit
roller position guide to make sure the push rollers are set on top of the Supplement
grit rollers.
• The media must always be positioned over
the media sensor.
Push roller
Grit roller • See "Aligning the Push Rollers" about the
position of the push rollers.
Grit roller position guide

Push roller

Media

Media sensor

5
 When using the model with 4 push rollers
Use the 4 push rollers to push down the sides and center of the media.
Supplement
Use the grit roller position guide and make sure the push rollers are on
top of the grit rollers.
• The media must always be positioned over
the media sensor.
You can adjust the center push roller's hold-down force. • See "Aligning the Push Rollers" about the
position of the push rollers.
Push roller

Grit roller position guide

• See "Aligning the Push Rollers" for
information about push roller hold-down
force.

Push roller

Grit roller

Media sensor

(The push roller is on top of the grit roller.) (The push roller is on top of the grit roller.)

(The center push roller is not on top of the (The center push roller is near the edge.)
grit roller.)

When Feeding Long-axis Media (at exceeds 2 meters)

Position the push rollers at least 15 mm inside the edges of the media.
Push roller

15mm 15mm
Media

When Feeding Long-axis Media (at least 2 meters)

Position the push rollers at least 5 mm inside the edges of the media.
Push roller

5mm 5mm
Media

6 Pull the media taut to make sure that there is no slack in the conveyance path, and then raise the media set lever to
lower the push rollers.

Media set lever

6
 7 Release the lock from the media stopper (Pull the sides and slide it forward).

Release
the media
stopper

Media stopper

8 When the set lever is up (and the media is held down by the push rollers)
Supplement
and the media stopper is unlocked, pull out the roll media and give it
slack. Dirt from the floor may stick to the media when
giving it slack, so please be careful.

Give it slack

Create the same amount of slack in the media as will be used for the
back of the machine. When using the roll media tray
Create the same amount of slack in the media
as will be used for the back of the machine.
Step 1: Raise the set lever
and fix the media.
Step 2: Create slack.

Give it slack

Loading Sheet Media

1 Lower the media set lever to raise the push rollers.

Supplement
Push roller See "Aligning the Push Rollers" about the
Media set lever
Media sensor position of the push rollers.

7
2 Make sure that the sheet media completely covers the media sensor.

Media sensor

3 Position the media and the push rollers to correspond with the width of
Supplement
the media.
Refer to the description of "Loading Roll
Media".

4 Pull the media taut to make sure that there is no slack in the conveyance path, and then raise the media set lever to
lower the push rollers.
Set the sheet media so that the paper's edges line up with the guideline on the front side.
Media set lever

Line up

When using the model with media guide bar

4 Pull out the front media under the media guide bar.

Media guide bar

5 You can set the media straight by stacking media you pull out and matching the edges up together.
After you check to make sure there's no slack, raise the media set lever and fixate the sheet media in the push roller.

Media set lever

Line up
Media guide bar

8
3. Aligning the Push Rollers
This section describes how to alignment of the push rollers.

Aligning the Push Roller

Position the left and right push rollers to correspond with the width of the media. Adjust the push rollers so that they are
positioned above both the media and the grit rollers.
Position the push rollers within the grit roller position guides ensures that they are above the grit rollers.

Push roller

Grit roller position guide

(It isn't on the grit roller.) (It isn't on the grit roller.)

Grit roller

CAUTION
To move the push rollers, the media set lever must be in the lowered position.
Supplement
If a [confirming push roller point] message appears after setting the media and raising the media set lever, it means the right push
roller is not on the right grit roller, or that the left or center push roller is not on the proper grit roller. Make sure everything is set
correctly.

For minimum width media

Make sure that all push rollers are on the long right grit roller.Use the left side of the grit roller as a starting point and then
set the push rollers so that they're on both sides of the media.
The settable width of the media is 55 mm or more (Model with 2 push rollers) or 125 mm* or more (Model with 4 push
rollers).
* When using the model with 4 push rollers, and all push rollers are on the right grit
roller (wide), turn the center (all rollers but the side rollers) push roller hold-down
force OFF. Supplement
The model with 4 push rollers requires the
The model with 2 push rollers The model with 4 push rollers
center push roller hold-down force to be set
Grit roller Grit roller based on the media's width and material type
in order to keep the media in place.
Push roller Push roller

Media sensor Media sensor

Media Media
Lever Lever
Hold-down force: Hold-down force: Low
Normal (OFF)

Refer to "Changing the Hold-down Force".

9
4. About the Initial Setup screen
The Initial Setup screen appears only when powering up the Cutting Plotter for the first time after purchase. Here, you can
set "Display Language" and "Length Unit".
After the initial setup is completed, you can also select the menu from the READY status.
See "Connecting to the Power" for turning on the power.

1 Once the machine is powered on (with the " | " switch) a message will be displayed after the version is displayed.
Here, PLEASE DISPLAY LANGUAGE setting screen is displayed.

2 Use the POSITION ( ) keys to select the language.

(This manual assumes you chose the English language setting.)

3 Press the [ENTER] key.

After the DISPLAY LANGUAGE is selected, the LENGTH UNIT screen will appear.

4 Press the [1] key (METRIC) or the [2] key (INCH) to select the length unit setting.

5 Confirm the setting and press the [ENTER] key (SET).

Setting will be set, and the default screen is displayed.

5. Set the media type into the Plotter.

Set the media type into the Plotter depending on the preset media.

1 If you have already loaded the media, the MEDIA TYPE menu appears. CAUTION
Select the media type to suit the loaded media.
Release the media stopper.
Supplement
The CONTINUE menu parameter appears when
the media set lever is raised and then lowered
again after media was previously loaded, making
it possible to select the previous settings.
Plot starting with the edge of
[1] ROLL-1 FRONT EDGE
media.
Roll media
Plot starting with the preset
[2] ROLL-2 CURRENT POSITION
position.
Sheet media Set a sheet media. [3] SHEET
CONTINUE When similar media is reset [4] CONTINUE

Simple mode/ Normal mode

2 After the media is detected, the plotter is ready to receive data for cutting You can use the [SIMPLE] key on the default
or plotting. This status is called "READY status" of the default screen. screen to switch between Simple mode and
When setting is finished, the tool carriage's location will become the Normal mode. CE6000 will be reset once when
initial point. you switch.
Dfault screen is displayed. In Simple mode you can change easy settings
from the menu screen.
In Normal mode, you will be able to change
more detailed settings.
Simple mode and Normal mode are independent
from one another. The settings of the mode
you're currently in will take precedence.
Menu screen Menu screen For details, see "About Simple mode".
(Normal mode) (Simple mode)

10
6. Tool adjustment and test cutting
After setting the Tool/Speed/Force/Acceleration, make test cutting, and repeat until optimal condition is achieved.

1 Load the media for test cutting in the plotter.

CAUTION
2 Press the [COND/TEST] key in the default screen. Do not touch the Tool edge when power is
In Normal mode, CONDITION screen (1/3) is displayed. turned on or during operation.
In Simple mode, CONDITION screen (1/5) is displayed.

CONDITION screen CONDITION screen

(Normal mode) (Simple mode)

3 Set the Tool conditions (Tool, Speed, Force, Acceleration).

Setting the Tool conditions
For more information about the various cutting
conditions, see “Selecting Tool Condition”.

Ex.) TOOLS CONDITION Ex.) TOOLS CONDITION

Settings screen (Normal mode) Settings screen (Simple mode)

To make 1 cut with set value To make 3 cuts with set value and ±1 of set value
4 Make test cutting for one piece while Tool conditions are 4 Make test cutting for three pieces while Tool conditions
being set. are being set.

CONDITION screen CONDITION screen CONDITION screen CONDITION screen

(Normal mode) (Simple mode) (Normal mode) (Simple mode)

(1) Press the POSITION ( ) key (CUT TEST).

(1) Press the POSITION ( ) key (CUT TEST).
CUT TEST screen is displayed.

CUT TEST screen CUT TEST screen

(2) Press the POSITION ( ) key the tool carriage (Normal mode) (Simple mode)
to the location you wish to perform the test cutting.
(2) Press the POSITION ( ) key the tool carriage
Tool carriage to the location you wish to perform the test cutting.
(3) Press the [1] key (FORCE). Cut Order
3 cutting test patterns are cut,
with current FORCE in the
center, and 1 each of FORCE +1 Setting –1
increased and decreased for 1 values
(4) Press the [ENTER] key after completion.
It will return to CUT TEST menu screen.

Press the [ENTER] key. (5) Press the [2] key (CUTTER OFFSET). (Normal mode
CAUTION only)
Cut test pattern is cut.
When the [ENTER] key is 3 cutting test patterns are cut, with current CUTTER
pressed, the tool carriage OFFSET in the center, and 1 each of CUTTER OFFSET
will start moving, so take increased and decreased for 1.
care not to cut your fingers. (6) Press the [ENTER] key after completion.
It will return to CUT TEST menu screen.

11
 5 Check if the cut test is appropriate.
Confirm the cutting test results, and adjust to optimal setting. Repeat cutting test and adjustment until optimal cut is
achieved.
Adjustment of Offset
How to check offset
Check the corners of the triangles and rectangles. See "Setting the Tool"
Check if the offset value is set correctly by
and adjust the offset value if the corner is not cut or if it is cut too much.
following.
Adjust offsets in Normal mode.
Adjustment for Half Cutting Not enough adjustment. Increase
the offset value.
Peel off the triangle area, and adjust so it cuts slightly into the backing
sheet.
If the backing sheet has been cut through, either the FORCE setting is
Optimal offset value.
too high or the cutter-blade tip is extended too far. If the backing sheet
shows only a few traces of the cutter blade, either the FORCE setting is
too low or the cutter blade tip is not sufficiently extended.
See "Adjusting the Blade Length" and "Setting the Force" and adjust the
Too much adjustment. Decrease
settings.
the offset value.
Adjustment for Cutting Out
Adjust so the media is completely cut out.
If the media is not completely cut, either the FORCE setting is too low or the cutter blade tip is not sufficiently extended.
See "Adjusting the Blade Length" and "Setting the Force" and adjust the settings.
Adjustment When Using Plotting Pen
Adjust the FORCE so there will be no faint lines. To prolong the pen life, set the FORCE to the lowest setting without any
faint lines. See"Setting the Force" or setting the FORCE.

Adjust the Blade Length (Automatic Height Adjust)

Test cutting must be performed several times in order to confirm the optimal blade length setting. However, if the blade
length adjustment function is used, the optimal length can be easily set.

1 Load the media for test cutting in the plotter.

2 Press the POSITION ( ) key the tool carriage to the location you wish to perform the blade length adjustment.

3 Press the [COND/TEST] key in the default screen. Supplement

CONDITION setting screen (1/3) is displayed. Perform the settings in Normal mode.

4 Press the POSITION ( ) key.

CONDITION setting screen (3/3) is displayed.

5 Press the [3] key (BLADE ADJUST).

Message prompting to turn the blade-length adjustment knob is displayed.

12
6 As instructed, turn the blade length adjustment knob to the left to fully
retract the blade. CAUTION
Do not touch the Tool edge when power is
turned on or or during operation.
Supplement
See "Structure of Cutter Plunger" for
bladelength adjustment knob.

Blade

7 Set the cutter Plunger in Tool Holder 1 (Backward).

Supplement
8 Press the [ENTER] key.
Adjustment is only possible for the cutter pen
You can calculate the height by moving the tool up and down.
set in Tool Holder 1 (Backward). It does not
TO ACHIEVE THE TARFET LENGTH screen is displayed. apply to Tool Holder 2 (Forward).
See "Attaching a Tool" for instructions on
setting.

9 Press the [1] key (BLADE LENGTH TARGET).

BLADE LENGTH TARGET screen (TARGET) is displayed.

10 Press the POSITION ( ) key and increase or decrease the setting value.

11 Confirm the settings and press the ENTER key (SET).

The Blade Length Target will be selected, and you will return to the TO
ACHIEVE THE TARGET LENGTH screen.

12 Press the [2] key (CHECK).

You can calculate the height by moving the tool up and down.
Supplement
The amount and direction to turn the adjustment knob is displayed.
"T" is the target value of the blade length, and
"H" is the current blade height (amount).
Turning the blade-length adjustment knob
displays the number of turns and direction.

13 Turn the blade-length adjustment knob and adjust the cutter blade length.
CAUTION
[2] Current blade length is displayed by pressing the [2] key (CHECK) , so
adjust the blade length until it matches the thickness of the media. Depending on the loaded media, the blade
might sink in to the media, making accurate
14 Press the [3] key (END). measurement impossible.

Adjustment is completed and it will return to CONDITION screen (3/3).

15 Press the [COND/TEST] key.

I will be return to default screen. After completing the settings, press [ENTER] key.

13
 Installing the Software
Install the software housed in the attached DVD-ROM into the PC that is used.
This section explains how to install the software when using a Windows 10 (64 bit) operating environment.

Note
• IfUpon installation, be sure to log on Windows using an account with administrator privileges on your computer.
you have logged on using a standard user account, an [User Account Control] screen asking you to enter the
administrator account password may appear.
• This
Supported OS
software supports the following OS environments:
Windows 10 (32 bit/64 bit), Windows 8.1 (32 bit/64 bit), Windows 8 (32 bit/64 bit), Windows 7 (32bit/64bit),
(Plotter driver/Cutting Plotter Controller also supports Windows Vista.)
Mac OS X 10.11 to 10.7 / mac OS 10.12
(Graphtec Studio also supports Mac OSX 10.6.)
• Macintosh
When Using Macintosh
operating environments are supported by the following software.
Proceed with installation in accordance with your operating environment.
• Graphtec Studio : Software application that enables cutting data to be created through simple commands.
• Cutting Master 4 : Plug-in driver that can be directly operated from within Adobe Illustrator.
Note that Adobe Illustrator must be installed on your computer prior to use.
When checking the manual in the Macintosh operating environment, open the pertinent manual on the accompanying
DVD-ROM in the following sequence: [Mac] > [Manuals] > [English (Each language)] > [Manual According to Software].

• Setup in a Windows operating environment

1. Launching the Start Menu
< When using the DVD >
After starting up Windows, insert the [USER GUIDE & SOFTWARE DVD] provided with the CE6000 into your computer's
DVD drive.
The below screen will appear before the Start Menu launches.
Continue with installation in accordance with the following procedures.

1 The start-up message of DVD drive is displayed. Click on the message.

* When setting up the DVD in the computer, this message will disappear after a few seconds.

2 DVD operation screen is displayed.

Select the “Run MultiSetup.exe” from the DVD operation screen.

* If the DVD operation screen is not displayed, select the set DVD drive from the Explorer.
Open the DVD and double-click on [MultiSetup.exe].

14
3 Click [Yes] if you have logged on using an administrator account.
Supplement
If you have logged on using a standard user
account, an [User Account Control] screen asking
you to enter the administrator account password
may appear. Enter the password, and then click
[Yes].

4 The [Start] will appear.

"Use this menu to install the software you require to use the Cutting Plotter
First-time users should proceed with installation by clicking on [Install CE6000Plus Software]."
Proceed with installation according to your operating environment.

A. Install CE6000Plus Software:

Install the [Cutting Plotter Controller] and [Plotter Driver].
A B. Setup Graphtec Pro Studio:
"Software enabling cutting data to be created through simple commands.
B Create designs and edit characters/shapes using this software."
C C. Setup Cutting Master 4:
Plug-in driver that enables simple cutting through direct operation from
D within Adobe Illustrator and CorelDRAW.
Adobe Illustrator or CorelDRAW must be installed on your computer prior
to use.
D. Install User's Manual:
Installs the User's Manual.

15
A. Install CE6000Plus Software
If you are using the Cutting Plotter for the first time, click on 3 The [Select Program Folder] window will appear.
[Install CE6000Plus Software] to install the device. Simply click on [Next].
This operation will install the [Cutting Plotter Controller]
and [Plotter Driver].

4 When the next screen appears, click on [Finish].

Note Do not connect the accompanying USB cable yet.

Doing so may prevent the [Plotter Driver] from
being installed properly.
Refer to the procedures in this User's Manual
when connecting the USB cable.

Installing the [Cutting Plotter Controller]

1 Click on [Install CE6000Plus Software]. This concludes the installation of the [Cutting Plotter
The [Setup] screen to setup Cutting Plotter Controller Controller].
for CE6000 will appear momentarily. Next, install the [Plotter Driver].
Click on [Next].

Installing the [Plotter Driver]

5 After installation of the [Cutting Plotter Controller]
is complete, the [Setup] screen for the [Graphtec
CE6000Plus Driver] will appear momentarily.
When it does, click on [OK].

2 The [Chose Destination Location] screen will appear.

Check the installation destination folder displayed. If
there is no need to change it, click on [Next].
6 Next, check to make sure the [Cutting Plotter] is not
connected to your computer, then click on [Next].

7 Click on [Next] again.

16
8 A window for selecting the [Port Name] to be used Connecting the USB Cable
appears.
Select [USB]. 11 First, make sure that Windows 10 has been launched
Clicking on [Next] will begin the driver installation successfully.
process. Next, connect the USB cable accompanying the Cutting
Available Port Names Plotter to your computer. Ensure that the Cutting Plotter
is turned off when you do.
USB : Selected when a USB cable is used for
connection. (1) Ensure that the Plotter's power is turned off (" "
COM1 : Selected when an RS-232C (serial) cable is position).
used for connection.
FILE : Selected to save outputted data (plot data) to
a file.

Select "USB"

(2) Connect the power cable.

Supplement (When selecting the COM1)

To select "COM1" in "Selecting Port Name", do the
installation according to the message.
After the installation is completed, connect the RS-232C
(3) Connect the USB cable.
cable. ( For more information about connecting the RS-
232C cable, see "Connecting the computer" in User's 1. Connect to your computer.
Manual.)
To connect the COM1 for RS-232C, the Cutting Plotter must
be set to "Normal mode". For more information about setting
the COM1, see "Preparing to Cut" in User's Manual.

2. Connect to the

9 The [Windows Security] screen will appear momentarily.

Cutting Plotter.
USB cable
Click on [Install] to install the [Plotter Driver].
12 Turn on the Cutting Plotter.

10 Next, the [Update for the Graphtec CE6000Plus driver

was completed] screen will appear.
Click on [OK] to reboot your computer. 13 Installation of the device starts.
After a while, the printer icon of Plotter will be added
in the "Devices and Printers" screen.
* To display the "Devices and Printers" screen, display the
"Control Panel" screen from the Start menu and then click
on the [Devices and Printers] in the [Hardware and Sound].

his concludes the installation of the driver software.

Next, please install the software applications.
This concludes the installation of the [Plotter Driver]. Install the software in accordance with your operating
After rebooting your computer, follow the below procedures environment.
to connect the USB cable.

17
B. Setup Graphtec Pro Studio
Please download the User's Manual separately from our website and perform the setup.

C. Set Up Cutting Master 4

Please download the User's Manual separately from our website and perform the setup.

D. Install User's Manual

Follow the below procedures to install the User's Manual 2 When this screen appears, click on [Finish].
(pdf format).
Adobe Reader must be installed on your computer in order
to read the manual.

This concludes the installation of the [User's Manual].

The newly-installed [User's Manual] will be registered
under your Windows Start Menu.

Installing "User's Manual"

1 Click on [Install User's Manual].
The [CE6000 User's Manual Setup] screen will appear
momentarily.
Click on [Next].

18
• Setup in a Macintosh operating environment
A. Set Up Cutting Master 4
Please download the User's Manual separately from our website and perform the setup.

B. Setup Graphtec Studio

Please download the User's Manual separately from our website and perform the setup.

19
621588810