2020 Cebis and Cemos Training Presentation Data Min

LEXION 8800 - 6800
CEBIS and CEMOS Training Guide 2020

CEBIS Guide
Company: CLAAS of America Inc.
Address: 8401 South 132nd Street

Omaha, NE 68138
Phone: 402-861-1000
Fax: 402-861-1003
Website: www.claas.com
Images and content are intended to cover ALL features and options available on 2020 LEXION combines.
Content may vary on each machine configuration.
LEXION Model: 8800 - 6800
Build Year: 2019
Effective Date: 6/1/2019
Last Revision: 6/8/2020
2 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

Contents
Cab Overview 4
CEBIS controls and setup 21
Setting CEBIS for harvest 28
Header and CONVIO CEBIS setup 43
CEMOS 57
CRUISE PILOT setup and controls 60
QUANTIMETER setup 70
CEMOS integrated in CEBIS setup 72
CEMOS in CEBIS MOBILE setup 76
GRAIN QUALITY CAMERA 88

Console Functions
Cab Overview

Ignition and Accessibility Cab & Comfort
Feature:
1. Ignition
2. 12 V socket, 2 pin
3. 12 V socket, +15 A
4. 12 V socket, +30 A 1
5. Diagnosis socket
6. USB interface
2 3
4

Lighting
Procedure:
1. Rotate master light switch (1) to far right position to turn
lights on
2. With the master light switch on, the lights can be turned
on/off individually by pressing their respective buttons (2)
3. Beacon lights (3) can be turned on/off regardless of dial
position
4. Beacon lights setting can be changed in CEBIS
3 1
Green indicates light is on

Multi-function Armrest
8 9 10 11 12 13 1. CEBIS TOUCH
2. CEBIS control panel
1 3. Arm rest
6
4. Arm rest position control lever
5. Throttle switch
6. Radio & Bluetooth control panel
7. Multifunction Handle
8. Reverse Pushbutton
7
9. Forward Pushbutton
10. - Volume Pushbutton
2
6
11. + Volume Pushbutton
12. Hang up Pushbutton
5
13. Accept Pushbutton

Armrest
Feature:
1. CMOTION ground speed control lever
2. CEBIS control panel
3. Settings adjustment
4. Diesel engine speed switch
5. Radio and phone control panel

Button Layout
7 8 9 10
6
5
4
Feature:
1
1. Reverse front attachment
2. Front attachment engagement
3. Processor engagement
 3 position toggle switches 4. Threshing drum speed
• Forward: Increase 5. Concave clearance
• Reverse: Decrease 6. Cleaning Fan
• Middle: Neutral, not activated 7. Upper sieve gap
 Enables quick change of machine settings
8. Lower sieve gap
directly
 Replaces CEBIS rotary dial options 9. Rotor speed
10. Rotor cover plates

CMOTION Handle
C8x CMOTION handle

Feature:
 Buttons for defined, updated symbols
1. Lower reel
 New HOTKEY buttons for new CEBIS
2. Reel forward TOUCH functions
3. Raise reel
4. Reel backwards
5. Change HOTKEY function down 1 2 3 4
5 6 7
6. Change HOTKEY function up
7. Display HOTKEY function
8. AUTO PILOT ON
9. Raise front attachment
10. CAC height control
11. Lower front attachment
12. Pre-set height control 13 12 11 10 9
8
13. Header stop

Transmission gear select
Procedure:
1. Move CMOTION handle to neutral
2. Throttle to low idle position
3. Tap (1) to change gear up
4. Tap (2) to change gear down
DO NOT APPLY SERVICE BRAKE

Road Travel Switch
Switching Road Travel switch to Road Travel

Procedure:
1. Push the Road Travel switch (1) down
Switching Road Travel switch to Fieldwork

Procedure:
1. Unlock the Road Travel switch (1) and push up on
black tab and rock switch forward

Processor & Feederhouse on/off
Processor Procedure:
1. Throttle to Low
2. Pull yellow switch back to engage
3. Switch will remain back
Feederhouse Procedure:
1. Throttle to Low
2. Pull yellow switch back to engage
3. Switch will return to neutral

Reversing front attachment
Procedure:
1. Hold down the Reverse front attachment button (1) and push
the Front attachment button (2) forward

Controls and Hotkey
5 1
2
 The HOTKEY menu (5) is displayed in CEBIS when one of the
HOTKEY buttons (2) are pressed.
 Once a function is selected, it is then controlled by the trigger (6) on
the CMOTION handle
Feature:
1. CEBIS scroll wheel
2. HOTKEY buttons
3. Information
4. Escape/Back
6

Road travel screen
Feature:
1
1. Main Menu
4
2. Def Level
3. Coolant Temp
5 8
4. Analog Speedometer
5. Engine Speed
6. Gear Indicator 7
7. Digital Speedometer
8. Fuel Level 3 2

Harvest screen
Feature:
1. Main Menu 2 5 1
2. Header Cutting Height (CAC)
16
3. Surface of the ground
4
4. Header cutting height (ground pressure) 8
3
5. Pre-set cutting heights above
6. User defined display 6
7. User defined display 2
8. Machine settings information 10 11 12 13
9 14 7
9. Returns volume
10. Returns volume grain
11. Rotor loss
12. Sieve loss 15
13. Foreign matter
14. Broken grain
15. Gear and POWERTRAC display
16. Crop selection information

Main menu items
Main Menu Layout

1. Header: Header type, Automatic functions,
2. Drive: Dynamic Power and ground drive
information
3. Machine: All internal machine functions and
adjustments
4. AUTOMATIC: All combine automatic functions
5. Crop: Crop data, QUANTIMETER, Grain
Moisture, GRAIN QUALITY CAMERA
6. Work records: Field work recordings
7. Counter: Machine hours and information
8. Service: Maintenance recorder, Central
lubrication system, Programming operations,
Vehicle and engine diagnosis, Alarm lists
9. Settings: Basic machine settings
10. Information: CEBIS software information

Setting controls
Changing a settings value

Procedure:
1. Use CEBIS control dial to scroll triangle around
settings circle
2. Use touchscreen function to drag triangle around
settings circle
3. Use touch screen function to touch directly on the
settings circle and triangle will move to that position
4. Touch +/- to move triangle up and down on the bar
5. Dragging the triangle between the +/- buttons up or
down
6. Touch center of settings circle to key in value directly

Teaching in operations (learning procedures)
Procedure:
A. Pressing green box with arrow (1) begins teaching in
operation
B. Operator must follow on screen commands
C. Progress of the teaching in operation can be viewed by
the progress bar (2)
D. Teaching in procedure can be aborted by pressing escape
button on the console

A. CEBIS Settings

Step 1a: CEBIS language and measuring units
When to perform: as needed

Navigate to: Settings (1) / Basic settings (2) / Language (3)
A. Language settings: set your preferred CEBIS display 3
language
B. Measuring unit settings: set your preferred CEBIS
display units of measure
2
1

Step 2a: CEBIS display settings

Navigate to: Settings (1) / Display settings (2)
Procedure:
A. Select CEBIS display screen mode: day or night
B. Adjust CEBIS display screen brightness using brightness
adjustment
C. Turn automatic night mode on or off

Step 3a: Camera Settings

Navigate to: Settings (1) / Camera input 1 (2)
2
Procedure: 1
A. 1. Select what camera display operator would like to

appear in the Camera input 1 display window
B. 2. Select what camera display operator would like to
appear in the Camera input 2 display window
C. Tap camera icon (3) to view camera in full screen
CEBIS CAN ONLY HAVE TWO CAMERA INPUTS

Step 4a: User Defined Display Setting

Navigate to: Settings / User-defined display / 1st line 2
1
Procedure:
A. 1. Select 1st line (1)
B. 2. Select desired display setting from drop down list (2)
C. 3. Repeat for all other lines
D. 4. Repeat procedure for User-defined display 2

Step 5a: User Type Setting

2
Navigate to: Setting (1) / User Type (2) / Select Type (3)
Beginner: Prohibits the operator from making adjustments to 3
the machine
Normal: Allows the operator to make basic machine
adjustments
Expert (RECOMMENDED): Allows the operator full access
to all machine functions

Step 6: CEBIS Hotkey Setup

Navigate to: Settings (1) / Favorite Management (2) /
Assignment (3)
Procedure:
A. Select Position. Pop-up menu will appear
B. Scroll through menu and select desired Hotkey function
using CEBIS touchscreen or CEBIS dial

B. Setting CEBIS for Harvest

Step 1b: Engine speed sensor calibration
When to perform: at the start of harvest

2
Navigate to: Drive (1) / Diesel engine (2) / Max engine
speed (3) 3 1
Procedure:
A. With engine running, select max engine speed to start

teaching-in operation

Step 2b: Machine speed sensor calibration
When to perform: at the start of harvest or after servicing

2
Navigate to: Machine (1) / Speeds (2)
3
Procedure:
A. Start engine and processor; set throttle to max
B. Select start teach-in operation to learn all belts speeds
Perform engine speed calibration (Step 1) first followed
by belt speed calibration (Step 2)
1

Step 3b: Set sieve type
When to perform: at the start of harvest, after a sieve

change or reconnecting a sieve motor
2
Navigate to: Machine (1) / Cleaning (2) / Sieve type
Procedure:
3
A. Select sieve type for upper and lower sieve 1
B. Press Upper sieve end stops to start learning procedure
C. Repeat for Lower sieve

Step 4b: Set up returns monitor
When to perform: at the start of harvest, when changing

crops
Navigate to: Machine (1) / Cleaning (2) / Returns volume
limit (B)
Procedure:
A. Engage processor and throttle to full
B. Press Returns volume limit button
C. Use touchscreen +/- or key in desired Returns volume
limit
D. Press the check mark to save your change

Step 5b: Loading crop settings
When to perform: when changing to a new crop type

2
Navigate to: Crop (1) / Crop data (2) / Select crop data (3)
Procedure:
3
1. Start engine, engage processor and throttle to high
2. Select a crop type from the crop menu
3. Press  to start loading crop settings
4. Green circles appear once crop has been loaded,
If there is an error when loading crop settings, a red
1
circle will appear

Step 7b: Saving crop settings

Navigate to: Crop (1) / Crop data (2)
Procedure:
A. Start engine and engage processor and feederhouse
B. Press +folder icon to create new crop settings
C. Name crop type folder and press check mark to save crop
settings

Step 8b: Setting crop favorites

2
Navigate to: Crop (1) / Crop data (2) / Favorites (3)
Procedure:
A. Select Favorite 1
B. Scroll through the list until you find desired crop and
select it
C. Repeat the process for Favorite 2 and Favorite 3 3
1
Selecting crop favorites from Harvest Screen:
A. Press crop icon on top tool bar of Harvest Screen (1)
B. Select crop favorite from side pop up menu (2)

Step 9b: Learn feederhouse and header travel limits
When to perform: after every header change (except for

1
CONVIO which saves first calibration)
B
Navigate to: Header (1) / learning processes of header
(2)
Procedure: 2
A. Start engine and engage processor and feederhouse,

throttle to full
B. Press green box with arrow to start learning procedure
C. Follow the commands given to you on the CEBIS screen
D. Repeat the process for all necessary header learning
procedures

Step 10b: QUANTIMETER calibration
When to perform: beginning of harvest (each crop type) and

periodically throughout harvest to confirm accuracy
3 2
Navigate to: Crop (1) / QUANTIMETER (2)
Procedure:
Zero calibration:
1. Start engine and engage processor, throttle to full
2. Calibrate zero yield (zero cal function) by selecting
Teaching-in (wait for message to confirm calibration has 1
completed)
Calibrating yield sensor:
1. Press test-weighting (3) to turn on calibrating process
2. Harvest a load of grain that can be measured (half a grain
tank minimum)
3. Press test-weighting (3) to turn calibrating process off.
Weight of crop size will appear underneath combine icon
4. Unload into a cart with scales and enter the actual grain
weight in the cart icon (4). Press weight and grain pile
icon to type in weight
5. Calibration factor will automatically be adjusted and
appear in the calibration factor button
6. Calibration factor can be saved for each crop under crop
type settings
 Perform before saving custom crop settings (Step 6)

Step 11b: AUTO CROP FLOW

Navigate to: AUTOMATIC (1) / AUTOMATIC (2) 2
Procedure:
A. Turn master switch ‘ON’ (3)
B. Scroll down to settings (4)
1
C. Tap ‘Sensitivity of the AUTO CROP FLOW (5) to select
sensitivity
3
 Low: slower reaction
 Medium (recommended): moderate reaction
 High: fast reaction
 If too sensitive, lower sensitivity
5

Step 12b: Residue Management

Navigate to: Machine (1) / Straw and chaff processing (2)
3
Procedure: 2
A. Tailboard position (3) 4 5
B. Engage or disengage friction plate (4) 1
 Engaged = finer cut

6
C. Engage or disengage stationary knives (5)
 0 (fully retracted) = large particle size
 1 (engaged halfway) = medium particle size
 2 (fully engaged) = fine particle size
D. Straw chopper speed selection (6)
 High speed: soybeans, small grains and rice
 Low speed: corn
E. Teach in distribution system by pressing and following on
screen commands
 Perform at beginning of season

Step 13b: Setting threshing speed range high/low

Navigate to: Machine (1) / Threshing mechanism (2) /
Threshing cylinder reduction gearbox (3)
Procedure:
A. Start engine, do not start processor
B. Tap Machine button
C. Tap threshing mechanism button
D. Tap threshing cylinder reduction gearbox
E. Set drum speed reduction gearbox to high or low (4)
4
High speed
Low speed

Step 14b: Setting threshing speed range high/low

Navigate to: Machine (1) / Threshing mechanism (2)
Procedure:
A. Start engine, do not start processor
B. Tap Engageable threshing concave bar to engage or
disengage
C. Tap Threshing concave flap to close or open main
concave threshing flap

Service page teaching-in (learning) procedures
When to perform: at specified intervals

Navigate to: Service (1) / Programming operations (2)
3
Procedure:
2
A. Select function that you want to calibrate
B. Press green arrow to start learning procedure
C. Follow commands on CEBIS screen until procedure is
finished
1
D. Repeat as necessary

C. Header and CONVIO CEBIS setup

Step 1c: Header type

CONVIO)
Navigate to: Header (1) / Header specification (2)
Procedure:
A. Tap Header type (A)
B. Select header type from pop up menu (B)

Step 2c: Setting header working width

CONVIO)
Navigate to: Header (1) / Header specification (2)
Procedure:
A. Tap working width button (A)
B. Use +/- buttons to enter header working width (B)
C. Press check mark (C) to save changes

Step 3c: Turning on automatic header functions

Navigate to: Header (1) / Automatic header functions (2)
Procedure:
A. Turn on desired automatic reel functions (3):
 Auto reel speed
 Auto reel height
 Auto reel fore/aft
 Auto reel overload protection
B. Turn on Lateral leveling with preselected height control
(AUTO CONTOUR)
C. Automatic header pitch ON/OFF
D. AUTO BELT SPEED ON/OFF (CONVIO draper head)

Step 4c : Adjusting CONVIO AUTO BELT SPEED center offset

Navigate to: Header (1) / Settings on the header (2)
Procedure:
A. Tap center belt speed icon
B. Use +/- to change center belt speed offset to ground
speed (3)
 Range: 0.0 – 0.6
C. Tap the check mark to save changes (4)
CENTER BELT SPEED RUNS FASTER THAN SIDE BELT

SPEED TO ENSURE SMOOTH FEEDING

Step 5c: Adjusting CONVIO AUTO BELT SPEED side belt offset

Procedure:
A. Tap side belt speed icon
B. Use +/- to change side belt speed offset
 Range: -1.2 – 2.5
C. Tap the check mark to save changes
SIDE BELT SPEED RUNS SLOWER THAN CENTER BELT

SPEED TO ENSURE SMOOTH FEEDING

Step 6c: Adjusting CONVIO cutter bar pressure

Procedure:
A. Tap pressure setting button
B. Enter desired CONVIO cutter bar pressure
C. Tap the check mark to save changes
PSI range is from 653 – 1305
Lower PSI means higher cutter bar ground pressure
Higher PSI means lower cutter bar ground pressure

Step 7c: Setting belt slip limits

Navigate to: Header (1) / Header specifications (2) / Draper
belt slip limits (3)
Procedure:
A. Tap side belt slip limit button
B. Enter desired draper side belt slip limit setting
C. Tap the check mark to save the changes
D. Repeat the process for center belt slip limit

Step 8c: Canola cross augers on/off

Navigate to: Header (1) / Header specifications (2) / Cross
auger (3)
Procedure:
A. Tap the cross auger button to turn cross augers on/off
TURNING CANOLA CROSS AUGERS ON/OFF WILL
ALSO TURN SIDE KNIVES ON/OFF IF EQUIPPED

Step 9c: CONVIO cutter bar operating modes
When to perform: when changing crops or as needed

Navigate to: Header (1) / Header specifications (2) / AUTO
CONTOUR operation mode (3)
Select:
A. Grain – rigid cutter bar for standing small grains
B. Flex manual – sets cutter bar at its lowest pressure
setting
C. Lodged grain FLEX – operator can switch between rigid
(standing) and flex (lodged) modes using pre-set cutting
heights button on the CMOTION handle
D. AUTO FLEX – cutter bar flexes up and down based on
AUTO CONTOUR ground pressure

Step 10c: Setting AUTO CONTOUR sensitivity
When to perform: when changing header or as needed

Navigate to: Header (1) / Header specifications (2) / AUTO
CONTOUR sensitivity (3)
Procedure:
A. Tap to change vertical sensitivity
 Press check mark to save changes
B. Tap to change lateral tilt sensitivity
 Press check mark to save changes
HIGHER SENSITIVITY MEANS SYSTEM WILL REACT
FASTER TO CHANGING TERRAIN

CEMOS setup and controls guide
CLAAS LEXION combines

Overview
CEBIS MOBILE
 CEMOS AUTOMATIC
 CEMOS DIALOG
CEBIS
 CEMOS AUTOMATIC
 CRUISE PILOT
 Combine adjustment
This setup guide is a supplement to the CEBIS guide.

For information on how to navigate CEBIS and how to set up other
features please refer to the CEBIS and controls guide.
This setup guide is not a substitute for the Operator’s Manual. Further
information concerning CRUISE PILOT and CEMOS is available in the
Combine Operator’s Manual and CEBIS MOBILE Operator’s Manual.

CRUISE PILOT and CEMOS AUTOMATIC Symbols
Description Function
Machine controls speed based on throughput,
CRUISE PILOT
grain loss, or engine load
AUTO Machine automatically adjusts threshing
THRESHING cylinder speed and concave clearance
AUTO Machine automatically adjusts rotor speed
SEPARATION and rotor cover flaps
AUTO Machine automatically adjusts upper and
CLEANING lower sieve opening and fan speed
AUTO Machine automatically adjusts chopping drum

CHOPPING speed, stationary knives and friction plate
GRAIN
Camera for viewing non-grain material and
QUALITY
cracked grain in the grain tank
CAMERA
System using rotor cover flaps to compensate
4D CLEANING
for side slopes
System using 3D sieve functions to

AUTO SLOPE
compensate for fore and aft slopes
Automatic throughput control using cruise pilot
AUTO CROP
sensors for overload protection of the
FLOW
machine

D. CRUISE PILOT setup

Step 1d: CRUISE PILOT master switch
When to perform: at the start of harvest, ensure “on” is

selected to utilize CRUISE PILOT features
Navigate to: CRUISE PILOT (1) / ON - OFF (2) / ON - OFF
(3)
Procedure:
A. Off: disables CRUISE PILOT features
B. On: enables CRUISE PILOT features

Step 2d: Set strategy
When to perform: after master switch is switched on,

change if different driving strategy is desired
Navigate to: CRUISE PILOT (1) / Settings (2) / Setting the
strategy (3)
Procedure:
Choose one of the following option:
a. Cruise control: harvests at a constant ground speed
b. Constant throughput: Automatically adjusts ground
speed to maintain a constant throughput based on the
crop thickness measured in the feederhouse
c. Maximum throughput with grain loss sensing
(recommended): Automatically adjusts ground speed to
maintain a constant throughput (bu/hr), while maintaining
acceptable grain loss within the limits of the loss monitor

Step 3d: Learning zero throughput
When to perform: after an extended period of inactivity and

periodically throughout the day, as conditions change
Navigate to: CRUISE PILOT (1) / Settings (2) / Start teach-
in operation (3)
Procedure:
A. Engage processor and feeder house (do not harvest crop
at this time)
B. Full throttle
C. Start teach-in process to learn zero throughput

Step 4d: Set target speed
When to perform: after selecting cruise control strategy

Navigate to: CRUISE PILOT (1) / Settings (2) / Set target
speed (3)
Procedure:
Set desired speed to be maintained when operating in cruise
control strategy
 Set ground speed (range: 1.2 – 9.9 mph)
 Not available if using either throughput strategy

Step 5d: Set target throughput
When to perform: after selecting either constant

throughput or maximum throughput with grain loss
sensing
Navigate to: CRUISE PILOT (1) / Settings (2) / Target
throughput (3)
Procedure:
Set desired throughput level to be maintained when
operating in either throughput strategy
Manual setting:
 Adjust target throughput number manually using the
HOTKEY or enter the value on the settings dial
 Range: 10 – 150 (recommended to start at 60-70)
Automatic setting:
 Start harvesting until feederhouse is full (50-100 yards)
 While harvesting, press and hold the A-button on the C-
MOTION handle to set new value (hold for three seconds
until it beeps)
 To increase or decrease throughput performance, adjust
the value until desired throughput is reached
 Not available if using cruise control strategy

Step 6d: Set maximum speed
When to perform: after selecting desired strategy

Navigate to: CRUISE PILOT (1) / Settings (2) / Maximum
speed (3)
Procedure:
Set the maximum ground speed limit for use when little to no
crop is in the feederhouse (example: headlands and areas of
light crop or no crop)
 Range: 1.2 – 9.9 mph (example: 0.5 – 1 mph over harvest
speed)
 Set for all strategies

Step 7d: Set sensitivity

Navigate to: CRUISE PILOT (1) / Settings (2) / Sensitivity
(3)
Procedure:
Change how quickly the machine responds to changing field
conditions when operating with CRUISE PILOT
 Very gentle
 Gentle
 Medium (recommended starting setting)
 Aggressive
 Very aggressive
The more aggressive the setting, the faster the response

Step 8d: Unloading mode

Navigate to: CRUISE PILOT (1) / Settings (2) / Unloading
mode (3)
Procedure:
A. Off
 CRUISE PILOT will remain at constant harvest speed
 Recommended strategy
B. Emptying
 Ground speed is reduced by 15% and remains
constant while unloading on-the-go
 Pressing the A-button again deactivates this mode
 After unloading is complete, there are two ways to
resume selected strategy
 After the auger is swung in, the selected strategy will
resume
 If the auger remains swung out after unloading is
turned off, the selected strategy will resume after 30
seconds
 For use in very tough-to-thresh conditions

Step 9d: Set maximum engine load

Navigate to: CRUISE PILOT (1) / Settings (2) / Engine load
(3)
Procedure:
A. Choose max engine load that is allowed when CRUISE
PILOT is engaged
 Range: 85% – 104%

E. QUANTIMETER setup

Step 1e: QUANTIMETER calibration
When to perform: beginning of harvest (each crop type) and

periodically throughout harvest to confirm accuracy
3 2
Navigate to: Crop (1) / QUANTIMETER (2)
Procedure:
Zero calibration:
1. Start engine and engage processor, throttle to full
2. Calibrate zero yield (zero cal function) by selecting
Teaching-in (wait for message to confirm calibration has 1
completed)
Calibrating yield sensor:
1. Press test-weighting (3) to turn on calibrating process
2. Harvest a load of grain that can be measured (half a grain
tank minimum)
3. Press test-weighting (3) to turn calibrating process off.
Weight of crop size will appear underneath combine icon
4. Unload into a cart with scales and enter the actual grain
weight in the cart icon (4). Press weight and grain pile
icon to type in weight
5. Calibration factor will automatically be adjusted and
appear in the calibration factor button
6. Calibration factor can be saved for each crop under crop
type settings
 Perform before saving custom crop settings (Step 6)

F. CEMOS integrated in CEBIS setup

Step 1f: Master switch
When to perform: initial CEMOS AUTOMATIC set up

Navigate to: AUTOMATIC (1) / AUTOMATIC (2)
Procedure:
Press each button to turn on:
A. AUTO THRESHING automatically adjusts:
 Concave clearance
 Threshing cylinder speed
B. AUTO SEPARATION automatically adjusts:
 Rotor speed
 Rotor cover plates
C. AUTO CLEANING automatically adjusts:
 Upper sieve position
 Lower sieve position
 Fan speed
D. 4D CLEANING (function of AUTO SEPARATION)
E. AUTO SLOPE (function of AUTO CLEANING)
F. AUTO CROP FLOW

Step 2f: AUTO CROP FLOW Sensitivity

Navigate to: AUTOMATIC (1) / Settings (2)
Procedure:
A. Tap ‘Sensitivity of the AUTO CROP FLOW’
B. Select system sensitivity
 Low: system is slow to react
 Medium (recommended): system is quicker to react
 High: system is fast to react

Step 3f: Optimization strategy
When to perform: initial CEMOS AUTOMATIC setup, change if different combine performance is desired
Navigate to:
Gentle threshing Increase throughput
Improve threshing Increase throughput
Improve grain cleanliness Increase throughput
Improve chop quality Reduce fuel consumption
Improve straw quality Increase throughput

G. CEMOS integrated in CEBIS MOBILE setup

CEBIS MOBILE display
1. Main Display Area: Displays machine parameters and

settings
2. Secondary Display Area: Configurable by the operator;
displays machine functions and camera options
3. Main Menu: DIALOG, AUTOMATIC, CRUISE PILOT,
Help, Settings
4. Status Bar: Displays which CEMOS AUTO functions are
running. Green = active, Gray = inactive

CEBIS MOBILE Layout
1. Main Menu: Select main menu item to view function

menu
2. Function Menu: Select function menu item to view
function details
3. Function Detail: Displays the functions and settings
under the function details
4. Overview of Function: Displays the functions under the
selected function menu item

Overview of Working Displays
1. Main Display options: Changes the machine view and

camera on the main display
2. Straw Moisture: Indicates straw moisture
3. Header Settings: Tap to see header settings
4. Machine monitoring: Optimization suggestions appear
here
5. Status bar: Shows which automatic options are active
6. Reel Position
7. Type of Crop Divider
8. Reel Speed
9. Feederhouse Speed
10. Crop Type: Displays the crop type selected in CEBIS

1. Header: Tap header to view CEMOS DIALOG

optimization suggestions
2. Threshing: Tap threshing mechanism to view CEMOS
DIALOG threshing optimization suggestions
3. Separation: Tap rotors to view CEMOS DIALOG
separation optimization suggestions
4. Residue Management: Top chopper to view
CEMOS DIALOG chopping optimization suggestions
5. Spreading System: Tap to view straw spreader settings
and make optimization adjustments
6. Rotor speed and rotor cover plates
7. Upper and lower sieve gap
8. Fan speed
9. Threshing cylinder speed and concave clearance

1. Separation System: Tap to view separation settings and

adjustments
2. Wind Compensation and adjustments: Tap to view
wind compensation
3. Spreader settings and adjustments: Tap to view
spreader settings
4. Spreader overlap display
5. Alignment of spread direction
6. Spreading direction
7. Spread width
8. Chopper speed
9. Position of the stationary knives and friction plate

Step 1g: CEMOS settings in CEBIS MOBILE
When to perform: beginning of initial CEMOS AUTOMATIC

set up, will retain selection after machine reset
Navigate to: DIALOG (1) / Settings (2)
Procedure:
A. Demo mode: Should always be off when running
CEMOS AUTOMATIC
B. Machine monitoring (ON): Displays system information.
Needs to be on for CEMOS AUTOMATIC to function

Step 2g: Harvest conditions
When to perform: after master switch is switched on,

change strategy if different driving mode is desired
Navigate to: DIALOG (1) / Condition (2)
A. Straw condition
 Dry: straw moisture is dry (least aggressive)
 Normal: straw moisture is normal
 Damp: straw moisture is damp (most aggressive)
B. Crop condition
 Kinked or broken: crop condition is kinked or broken
(most aggressive)
 Laid: crop condition is laid
 Standing: crop condition is standing (least aggressive)
 Weed-infested: crop condition is weed-infested
C. Grain Condition
 Dry: grain moisture is dry
 Normal: grain moisture is normal
 Damp: grain moisture is wet

Step 3g: Machine equipment
When to perform: after machine reset, ensure machine

equipment matches machine configuration
Navigate to: DIALOG (1) / Condition (2)
Procedure:
A. Disawner plates: Lever open/closes blanking plates under
the APS grates
 Open: lever on right side feederhouse is flipped down
 Closed: lever on right side feederhouse is flipped up
B. Crop divider type: end divider on header

Step 4g: Master switch

Navigate to: AUTOMATIC (1) / AUTOMATIC (2)
Procedure:
Press each button to turn on:
A. AUTO THRESHING automatically adjusts:
 Concave clearance
 Threshing cylinder speed
B. AUTO SEPARATION automatically adjusts:
 Rotor speed
 Rotor cover plates
C. AUTO CLEANING automatically adjusts:
 Upper sieve position
 Lower sieve position
 Fan speed
D. 4D CLEANING (function of AUTO SEPARATION)
E. AUTO SLOPE (function of AUTO CLEANING)
F. AUTO CROP FLOW

Step 3g: Optimization strategy
When to perform: initial CEMOS AUTOMATIC setup, change if different combine performance is desired
Navigate to:
Gentle threshing Increase throughput
Improve threshing Increase throughput
Improve grain cleanliness Increase throughput
Improve chop quality Reduce fuel consumption
Improve straw quality Increase throughput

Step 6: CEMOS Dialogue

Navigate to: DIALOG (1) / Start optimization (2)
Procedure:
A. Select one of the improvement or optimization strategy
B. Choose either to accept solution or move on to other
solution

H. Grain Quality Camera integrated in CEBIS MOBILE setup

Step 1h: Turning on GRAIN QUALITY CAMERA
When to perform: at the start of harvest, whenever AUTO

THRESHING is in use
Navigate to: AUTOMATIC (1) / Settings (2)
Procedure:
A. Tap GRAIN QUALITY CAMERA on / off button

Step 2h: Adjusting display of the proportion of cracked grain
When to perform: At the start of harvest; when changing

crops
Procedure:
A. Click on GRAIN QUALITY CAMERA window in CEBIS
MOBILE secondary display
B. Wait until an acceptable level of cracked grain (1) is
reached in the grain tank (cracked grain appears with a
purple outline on GRAIN QUALITY CAMERA)
C. Adjust sensitivity on dial (3) until display (2) fill amount is
between 50% and 60%. Touch dial to change sensitivity.
Adjust sensitivity incrementally until the desired level is
reached
D. If a high proportion of cracked grain is visible in the grain
tank and the displayed fill amount is low, increase
sensitivity until display fill amount is higher.
E. If a low proportion of cracked grain is visible in the grain
tank and the displayed fill amount is high, decrease
sensitivity until display fill amount is lower.

Step 3h: Adjusting display of the proportion of non-grain material
When to perform: At the start of harvest; when changing

crops
Procedure:
A. Click on GRAIN QUALITY CAMERA window in CEBIS
MOBILE secondary display
B. Wait until an acceptable level of non-grain material (1) is
reached in the grain tank (non grain material appears with
a purple outline on GRAIN QUALITY CAMERA)
C. Adjust sensitivity on dial (3) until display (2) fill amount is
between 50% and 60%. Touch dial to change sensitivity.
Adjust sensitivity incrementally until the desired level is
reached
D. If a high proportion of non-grain material is visible in the
grain tank and the displayed fill amount is low, increase
sensitivity until display fill amount is higher.
E. If a low proportion of non-grain material is visible in the
grain tank and the displayed fill amount is high, decrease
sensitivity until display fill amount is lower.

2020 Cebis and Cemos Training Presentation Data Min

Uploaded by

Copyright:

Available Formats

2020 Cebis and Cemos Training Presentation Data Min

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2020 Cebis and Cemos Training Presentation Data Min

Uploaded by

Copyright:

Available Formats

LEXION 8800 - 6800

CEBIS and CEMOS Training Guide 2020

Company: CLAAS of America Inc.

Address: 8401 South 132nd Street

LEXION Model: 8800 - 6800

Build Year: 2019

Effective Date: 6/1/2019

Last Revision: 6/8/2020

2 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

3 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

4 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

5 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

Green indicates light is on

6 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

7 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

8 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

9 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

C8x CMOTION handle

10 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

11 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

Switching Road Travel switch to Road Travel

Switching Road Travel switch to Fieldwork

12 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

13 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

14 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

15 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

16 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

17 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

Main Menu Layout

18 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

Changing a settings value

19 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

20 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

21 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

22 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

23 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

A. 1. Select what camera display operator would like to

24 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

25 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

26 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: as needed

27 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

28 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: at the start of harvest

A. With engine running, select max engine speed to start

29 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: at the start of harvest or after servicing

30 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: at the start of harvest, after a sieve

31 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: at the start of harvest, when changing

32 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide

When to perform: when changing to a new crop type

33 CLAAS of America Inc. | 2020 CEBIS and CEMOS Training Guide