1 | Overview Control Switch Control Bus type Function 3.

2 | Mount and wire the tamper switch 4 | Configuration

panels position panel
The B426 Ethernet Communication Module is a four-wire powered SDI, address For instructions on this optional switch (on GV4 Series and B Series Configure the B426 using one of the methods described in this section
SDI2, or option bus device that provides two-way communication with v2.xx control panels), refer to the Conettix Ethernet Communication for your control panel type.
compatible control panels over IPv4 or IPv6 Ethernet networks. B9512G/ 1 1 SDI2 Automation, Module (B426) Installation and Operation Guide (P/N: F01U266226)
The B426 on-board switch determines the bus address of the device. B8512G, Remote and the EZTS Cover and Wall Tamper Switch Installation Guide (P/N:
Configuration of the B426 is performed through the B426 configuration B5512/B4512/ Programming, F01U003734).
4.1 | PnP for SDI2 control panels
web pages. On SDI2 control panels, configuration can also be done on B3512, GV4, or
the keypad or through Remote Programming Software (RPS). Solution Reporting NOTICE!
2000/3000 3.3 | Wire to the control panel By default, when connecting a field replacement B426 to an
B9512G/ 2 2 existing SDI2 Control Panel, the panel overrides the module
When you wire a B426 to an SDI or SDI2 control panel, you can use
B8512G, GV4, settings. To keep custom module settings when you connect
either the module’s terminal strip labeled R, Y, G, B (PWR, A, B, COM)
Solution a module to a configured SDI2 control panel, you must
or the module’s interconnect wiring connectors (wire included).
2000/3000 disable Panel Programming using web-based configuration,
Figure 1.1 indicates the location of both the terminal strip and the
prior to connecting to the SDI2 bus.
GV4,GV3, 3 80 SDI Automation interconnect connectors on the module. Run the wires from the module
GV2, D9412G/ to the data bus terminals on the compatible control panel. Refer to When connected to a non-default SDI2 control panel, the control panel
4 88 Remote
D7412G/ Figure 3.2. automatically configures a connected module.
programming or
D7212G v6.3 1. Set the address switch to the correct address for the control panel
Reporting
or higher (SDI2 control panels use address 1 or 2).
NOTICE!
GV4 and GV3 5 92 Use either the terminal strip wiring or interconnect wiring 2. Connect the module to the control panel bus and apply power.
connector to the control panel. Do not use both. When 3. Program the control panel communication settings using RPS or
DS7240V2, 6 134 Option connecting multiple modules, you can combine terminal strip the keypad.
DS7220V2, and interconnect wiring connectors in series.
Easy Series
V3+, AMAX
4.2 | PnP for SDI or option bus control panels
When installing under the following conditions, the B426 needs no
Figure 1.1: Board overview DS7400Xi 7 13
further configuration:
DS7400Xi 8 14 Reporting – DHCP is available on your network.
Callout ― Description
– AES encryption is not required.
1 ― Ethernet RJ-45 port FPD-7024 9 250 Remote – Default B426 port settings (UDP on Port 7700) are permitted by
programming or the network administrator.
2 ― Yellow LINK LED Reporting
3 ― Green 100MB LED Table 2.1: Address switch settings 4.3 | Web-based configuration
4 ― Address switch For installations requiring non-default configuration, use the B426 web-
5 ― Heartbeat LED (blue) 3 | Installation based configuration pages.

6 ― TX and RX LEDs After you set the address switch for the proper address, install the To use the B426 configuration pages, you need the module’s IP address
module in the enclosure, and then wire it to the control panel and other or hostname.
7 ― Terminal strip
devices. – The default hostname for the module is the letter B followed
(to control panel or additional modules)
by the last six alpha-numeric digits of its MAC address (for
8 ― Interconnect wiring connectors example, B3F603F).
Caution!
(to control panel or additional modules) – Locate the IP address in the table on the DHCP server
Remove all power (AC and battery) before making any
9 ― Tamper switch connector connections. Failure to do so might result in personal injury (networked modules).
and/or equipment damage. – To use Auto IP, directly connect from your PC to the B426.
Within 60 seconds, the B426 temporarily assumes address
2 | Bus address settings 169.254.1.1 for configuration. (Refer to the Conettix Ethernet

One address switch determines the address for the B426 Conettix
3.1 | Mount the module in the enclosure Communication Module Installation and Operation Guide for
more information on using these methods.)
Ethernet Communication Module. The control panel uses the address Mount the module into the enclosure’s 3-hole mounting
for communications. Use a slotted screwdriver to set the address pattern using the supplied mounting screws and mounting
switch. bracket. Refer to Figure 3.1. NOTICE!
Before proceeding, ensure that the web browser is not
2
NOTICE! 1 configured to use a proxy server. Refer to the browser’s
The module reads the address switch setting only during online help for instructions on disabling proxy service.
power up. If you change the switch after you apply power
to the module, you must cycle the power to the module in Logging into web-based configuration (B426 Configuration Pages):
order for the new setting to be enabled. 1. Open an internet browser (Microsoft Internet Explorer or Mozilla
Firefox) and type in the B426’s IP address. The B426’s login page
Set the address switch per the Table 2.1. If multiple B426 modules opens.
3
reside on the same system, each B426 module must have a unique 2. Enter the password (the default is B42V2) and click Login. The
Figure 3.2: Wiring to the control panel (GV4 Series and FPD-7024
address. Figure 2.1 shows the address switch setting for SDI2 bus Device Information home page opens.
control panel shown) 3. Browse to the desired settings page and configure the
address 1.
parameters.
Callout ― Description 4. Click OK and then click Save & Execute to save and apply all
1 ― SDI2 control panel. For SDI control panels, wire R, Y, G, B to changes to the device.
the SDI bus.
Figure 3.1: Mounting the module in the enclosure 2 ― Interconnect wiring connectors

Callout ― Description 3 ― To Ethernet network

Figure 2.1: Address switch
1 ― Module with mounting bracket installed 4 ― Terminal strip wiring

2 ― Enclosure 5 ― Interconnect cable (P/N: F01U079745) (included)

3 ― Mounting screws (3) 6 ― Option bus control panel
5 | LED descriptions 6 | Certifications
The B426 module includes the following on-board LEDs to assist
Region Certification
with troubleshooting issues.
US UL 365 – Police Station Connected Burglar Alarm Units and Systems
Flash pattern Function
UL 609 – Local Burglar Alarm Units and Systems
Flashes once Normal state: Indicates normal operation state.
every 1 sec UL 864 – Control Units and Accessories for Fire Alarm Systems (Including NFPA 72)

UL 985 – Household Fire Warning System Units

3 quick flashes Communication error state: Indicates a bus UL 1023 – Household Burglar Alarm System Units
every 1 sec communication error. The module is not
receiving commands from the control panel. UL 1076 – Proprietary Burglar Alarm Units and Systems
UL 1610 – Central Station Burglar Alarm Units
FCC Part 15 Class B, NIST FIPS-197 AES Certification
(IP Communications)
On Steady Trouble state. Indicates a trouble condition Canada CAN/ULC S303 - Local Burglar Alarm Units and Systems
exists.
CAN/ULC S304 - Signal Receiving Centre and Premise Alarm Control Units
Off LED trouble state. Module is not powered, or ULC-ORD C1023 - Household Burglar Alarm System Units
some other trouble condition prohibits the
module from controlling the heartbeat LED. ULC-ORD C1076 - Proprietary Burglar Alarm Units and Conettix Ethernet Communication
Table 5.1: Heartbeat LED descriptions
Systems
Module
ICES-003 - Digital Apparatus B426
Flash pattern Function EU EN 50130-4, EN 61000-6-3, EN 60950
RX (Receive) Occurs when the module receives a message
Australia C-Tick
flashes over the network connection – UPD, TCP, or
DNS.
TX (Transmit) Occurs when the module sends a message 7 | Specifications en Quick Start Guide
flashes over the network connection – UPD, TCP, or
DNS. Dimensions 59.5 mm x 108 mm x 16 mm (2.19 in x 4.25 in x 0.629 in)

Table 5.2: RX and TX LEDs descriptions Voltage (operating) 12 VDC nominal

Current (maximum) 100 mA max
LINK (yellow) 100mb (green) Function
Connectors LAN/WAN: RJ-45 modular port (Ethernet)
flash pattern flash pattern
Off Off No Ethernet link Ethernet cable Category 5 or better unshielded twisted pair, 100 m (328 ft) max length
Interface IEEE 802.3 14 | Certifications
On Steady Off 10 BASE-T link
Data bus wire size 1.02 mm to 0.65 mm (18 AWG to 22 AWG)
Flash Off 10 BASE-T activity
Data bus wire length Maximum distance - Wire size:
On Steady On Steady 100 BASE-T link 150 m (500 ft) - 0.65 mm (22 AWG)
300 m (1000 ft) - 1.02 mm (18 AWG)
Flash On Steady 100 BASE-T activity
Web browser Microsoft Internet Explorer; Mozilla Firefox
Table 5.3: Ethernet LINK and 100mb LEDs descriptions
Compatibility AMAX 2000/2100/3000/4000
B9512G/B9512G-E, B8512G/B8512G-E
Condition Heartbeat Transmit Receive B5512/B5512E, B4512/B4512E, B3512/B3512E
(TX) (RX) D9412GV4/D7412GV4/D7212GV4
D9412GV3/D7412GV3/D7212GV3
Network cable On Steady Off 1 quick flash,
D9412GV2/D7412GV2/7212GV2 For complete installation, configuration, and testing instructions,
disconnected repeating
D9412G/D7412G/D7212G Version 6.3 or higher refer to the Conettix Ethernet Communication Module (B426) Installation
D9412/D7412/D7212
D9112 and Operation Guide provided on the supplied CD-ROM.
Obtaining an IP On Steady Off 2 quick flashes,
address repeating DS7220 Version 2.10 or higher
DS7240 Version 2.10 or higher
DS7400XiV4 Version 4.10 or higher Bosch Security Systems, Inc. Bosch Sicherheitssysteme GmbH
Easy Series V3+ 130 Perinton Parkway Robert-Bosch-Ring 5
FPD-7024 Version 1.02 or higher Fairport, NY 14450 85630 Grasbrunn
Solution 2000/3000 USA Germany
Low bus On Steady Off 3 quick flashes, www.boschsecurity.com
voltage repeating

Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.
Trademarks
Internal failure On Steady On Steady On Steady All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Table 5.4: Trouble conditions indicated through LEDs Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. website at
http://www.boschsecurity.com/datecodes/.
© 2015 Bosch Security Systems, Inc. F.01U.291.335 | 06 | 2015.08