Interfine® 878

Acrylic Polysiloxane
PRODUCT A high performance, two component, high solids finish which contains no free isocyanates, offers
DESCRIPTION compliance to current VOC legislation, and affords extended lifetime to first maintenance when utilised as
part of a high performance anticorrosive system.
Interfine 878 offers superior gloss and colour retention and provides significantly improved resistance to
yellowing & chalking when compared to typical conventional topcoats including catalysed acrylic, and
polyurethane finishes.

INTENDED USES Interfine 878 is a tough, hard wearing finish coat for application over properly primed surfaces, which
exhibits good flexibility, abrasion resistance, and affords protection against spills and splashes of a range
of chemicals such as acids, alkalis, solvents, and salt solutions. Suitable for application by spray and
roller, in both factory new construction and site maintenance application situations, and is an ideal
solution where legislation prevents the use of isocyanates, or restricts solvent emission levels.
For use in those market sectors where high standards of cosmetic appearance and aesthetics are a key
requirement. These include high performance steel constructions such as sports stadia, bridges, offshore
platforms, FPSO vessels, tank farms, chemical and petrochemical plants, pulp and paper mills, and the
power industry, in addition to general industrial and commercial steelwork where aesthetics are
important.

PRACTICAL Colour Wide range via the Chromascan system

INFORMATION FOR
INTERFINE 878 Gloss Level High Gloss

Volume Solids 72%

Typical Thickness 50-75 microns (2-3 mils) dry equivalent to

69-104 microns (2.8-4.2 mils) wet

Theoretical Coverage 12 m²/litre at 60 microns d.f.t and stated volume solids

481 sq.ft/US gallon at 2.4 mils d.f.t and stated volume solids

Practical Coverage Allow appropriate loss factors

Method of Application Airless Spray, Air Spray, Roller

Drying Time
Overcoating Interval with
recommended topcoats
Temperature Touch Dry Hard Dry Minimum Maximum

5°C (41°F) 6 hours 8 hours 8 hours Extended¹

15°C (59°F) 4.5 hours 6 hours 6 hours Extended¹
25°C (77°F) 3 hours 4 hours 4 hours Extended¹
40°C (104°F) 1.5 hours 2.5 hours 2.5 hours Extended¹

¹ See International Protective Coatings Definitions and Abbreviations

The drying times quoted have been determined at the quoted temperature and 50% relative humidity.
Overcoating intervals for recommended primers and intermediates are dependent upon actual
primer/intermediate used. Please see Systems Compatibility section.

REGULATORY DATA Flash Point Part A 34°C (93°F); Part B 55°C (131°F); Mixed 35°C (95°F)

Product Weight 1.34 kg/l (11.2 lb/gal)

VOC 2.05 lb/gal (246 g/lt) EPA Method 24
194 g/kg EU Solvent Emissions Directive
(Council Directive 1999/13/EC)
See Product Characteristics section for further details

Ecotech is an initiative by International Protective Coatings a world leader in coating technology to

promote the use of environmentally sensitive products across the globe.

Protective Coatings Worldwide Product

Page 1 of 4
Issue Date:07/07/2009
Ref:2103
 Interfine® 878
Acrylic Polysiloxane
SURFACE All surfaces to be coated should be clean, dry and free from contamination. Prior to paint
PREPARATION application all surfaces should be assessed and treated in accordance with ISO 8504:2000.

Primed Surfaces

Interfine 878 should always be applied over a recommended anti-corrosive coating scheme. The
primer surface should be dry and free from all contamination and Interfine 878 must be applied
within the overcoating intervals specified (consult the relevant product data sheet).

Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO
8501-1:2007) or SSPC-SP6, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch
primed prior to the application of Interfine 878.

APPLICATION Mixing Material is supplied in two containers as a unit. Always mix a complete unit
in the proportions supplied. Once the unit has been mixed it must be used
within the working pot life specified.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base
(Part A) and mix thoroughly with power agitator.

Mix Ratio 5 part(s) : 1 part(s) by volume

Working Pot Life 5°C (41°F) 15°C (59°F) 25°C (77°F) 40°C (104°F)
3.5 hours 2.5 hours 2 hours 1.5 hours

Airless Spray Recommended Tip Range 0.28-0.43 mm (11-17 thou)

Total output fluid pressure at spray tip not less
than 155 kg/cm² (2204 p.s.i.)
Air Spray Recommended Gun DeVilbiss MBC or JGA
(Pressure Pot) Air Cap 704 or 765
Fluid Tip E
Brush Suitable - small areas Typically 25-50 microns (1.0-2.0 mils) can be
only achieved

Roller Suitable Typically 50-75 microns (2.0-3.0 mils) can be

achieved

Thinner International GTA007 Do not thin more than allowed by local

environmental legislation

Cleaner International GTA007

Work Stoppages Do not allow material to remain in hoses, gun or spray equipment.
Thoroughly flush all equipment with International GTA007. Once units of
paint have been mixed they should not be resealed and it is advised that
after prolonged stoppages work recommences with freshly mixed units.
Clean Up Clean all equipment immediately after use with International GTA007. It is
good working practice to periodically flush out spray equipment during the
course of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays.

All surplus materials and empty containers should be disposed of in

accordance with appropriate regional regulations/legislation.

Page 2 of 4
 Interfine® 878
Acrylic Polysiloxane
PRODUCT The technology utilised in Interfine 878 is covered by patent (US 6,281,321 and EP 0 941290).
CHARACTERISTICS
Level of sheen and surface finish are dependent on application method. Avoid using a mixture of
application methods whenever possible.

Best results in terms of gloss and appearance will always be obtained by conventional air spray
application.

For brush and roller application, and in some colours, two coats of Interfine 878 may be required to
give uniform coverage, especially when applying Interfine 878 over dark undercoats, and when
using certain lead free bright colours such as yellows and oranges. Best practice is to use a colour
compatible intermediate or anticorrosive coating under the Interfine 878.

This product must only be thinned using the recommended International thinners. The use of
alternative thinners, particularly those containing alcohols and ketones, can severely inhibit the
curing mechanism of the coating.

Pot life times must not be exceeded even though the material may be still liquid and appear
useable. It is good working practice that application should commence with full unopened units of
material. Due to the moisture sensitivity with partially filled units of the curing agent component,
there is a danger of reaction with atmospheric moisture which could adversely affect the
performance of the final coating film.

Surface temperature must always be a minimum of 3°C above dew point.

When applying Interfine 878 in confined spaces ensure adequate ventilation.

Care must be taken when spray applying multiple coats of Interfine 878 to ensure that a continuous
wet film is applied to ensure a satisfactory coalescence occurs. Failure to do so may downgrade
appearance and performance.

Interfine 878 will cure satisfactorily at relative humidities between 40% and 85%. Curing will be
slower at lower humidities and faster at higher humidities.

Condensation occurring during or immediately after application may result in a matt finish and an
inferior film.

When overcoating after weathering or ageing, ensure the coating is fully cleaned to remove all
surface contamination such as oil, grease, salt crystals and traffic fumes, before application of a
further coat of Interfine 878.

Premature exposure to ponding water will cause colour change, especially in dark colours and at
low temperatures.

This product is not recommended for use in continuous immersion conditions.

Where prolonged chemical or solvent splashing is likely to occur contact International Protective
Coatings for information regarding suitability.

Note: VOC values are typical and are provided for guidance purpose only. These may be subject
to variation depending on factors such as differences in colour and normal manufacturing
tolerances.

Low molecular weight reactive additives, which will form part of the film during normal ambient cure
conditions, will also affect VOC values determined using EPA Method 24.

SYSTEMS Interfine 878 can be applied over a limited range of intermediates.

COMPATIBILITY
Absolute maximum overcoating intervals with Interfine 878 are dependent upon the
primer/intermediate. Relevant primer/intermediate product data sheet and Interfine 878
Recommended Working Procedures should be consulted prior to use.

Suitable intermediates are:

Intercure 200 Interseal 670HS

Intercure 200HS Interzone 505
Intergard 475HS Interzone 954
Interplus 356

For other suitable primers/intermediates, consult International Protective Coatings.

Page 3 of 4
 Interfine® 878
Acrylic Polysiloxane
D ADDITIONAL Further information regarding industry standards, terms and abbreviations used in this data sheet
et INFORMATION can be found in the following documents available at www.international-pc.com:
ail
T • Definitions & Abbreviations
o
p • Surface Preparation

• Paint Application

• Theoretical & Practical Coverage

• Interfine 878 Working Procedures

Individual copies of these information sections are available upon request.

SAFETY This product is intended for use only by professional applicators in industrial situations in
PRECAUTIONS accordance with the advice given on this sheet, the Material Safety Data Sheet and the
container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS)
which International Protective Coatings has provided to its customers.

All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and
fumes will be emitted which will require the use of appropriate personal protective equipment and
adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult International Protective Coatings
for further advice.

Rect Top
PACK SIZE Unit Size Part A Part B
Vol Pack Vol Pack
20 litre 16.67 litre 20 litre 3.33 litre 5 litre
5 US gal 4.17 US gal 5 US gal 0.83 US gal 1 US gal

For availability of other pack sizes, contact International Protective Coatings.

SHIPPING WEIGHT Unit Size Part A Part B
20 litre 25.4 kg 3.7 kg
5 US gal 54.7 lb 7.7 lb

STORAGE Shelf Life Part A 12 months minimum at 25°C (77°F).

Part B 6 months minimum at 25°C (77°F). Subject to re-inspection
thereafter. Store in dry, shaded conditions away from sources of heat and
ignition.

Rect
Bottom
Important Note
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product
(whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the
use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the
maximum extent permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of
law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to
our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the
light of experience and our policy of continuous development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to
using the product.

Issue date: 07/07/2009

Copyright © AkzoNobel, 07/07/2009.

, International and all product names mentioned in this publication are trademarks of, or licensed to, AkzoNobel.

www.international-pc.com

Page 4 of 4