2023 04 Online

Download as pdf or txt
Download as pdf or txt
You are on page 1of 84

999778002 - 04/2023

en-GB

The Formwork Experts.

Dokaflex table
User Information
Instructions for assembly and use (Method statement)
© by Doka GmbH, A-3300 Amstetten

9720-215-01

© by Doka GmbH, A-3300 Amstetten


User Information Dokaflex table

2 999778002 - 04/2023
User Information Dokaflex table

Contents
4 Introduction 71 Reshoring props, concrete technology and
stripping out
4 Elementary safety warnings
7 Services
73 Article list
8 System description
8 Dokaflex table – the tried-and-tested high-
speed tableform
9 System dimensions
10 Instructions for assembly and use (Method
statement)
15 Adaptation to building layout
19 Adapting to different slab thicknesses

21 Assembly
21 Assembling the table superstructure
22 Mounting the table heads
24 Mounting the floor props

26 Structural design

28 Tables around edges of slab


29 Tie-back solutions
31 Edge table with no downstand beam
33 Slab stop-ends
35 Edge table with downstand beam

37 Repositioning
37 General instructions on repositioning
38 Horizontal repositioning / travelling
41 Vertical repositioning with transport forks
44 Loading platform
45 Repositioning operation
47 Lining-and-levelling the Dokaflex tables

48 Table Lifting System TLS


49 Product description
50 Loading data
51 Areas of use, possible configurations
53 Repositioning and aligning the Table Lifting
System
54 Repositioning Doka tableforms
55 Anchoring on the structure
58 Possible ways of connecting the landing level
safety gates
59 Computation of quantities for Lifting masts
TLS 1.50m
60 Automatic climbing unit TLS

62 General
62 Combining with other Doka systems
63 Guardrail systems on the structure
65 Transporting, stacking and storing

999778002 - 04/2023 3
Introduction User Information Dokaflex table

Introduction
Elementary safety warnings
User target groups Remarks on this booklet
▪ This booklet is aimed at all persons who will be work- ▪ This document can be used as general Instructions
ing with the Doka product or system that it describes. for Assembly and Use (Method Statement) or be
It contains information on the standard design for incorporated into site-specific Instructions for
setting up this system, and on correct, compliant uti- Assembly and Use (Method Statement).
lisation of the system. ▪ The graphics, animations and videos in this doc-
▪ All persons working with the product described ument or app sometimes depict partially assem-
herein must be familiar with the contents of this bled assemblies and may require additional
booklet and with all the safety instructions it contains. safety equipment and/or measures to comply
▪ Persons who are incapable of reading and under- with safety regulations.
standing this booklet, or who can do so only with dif- The customer must ensure all applicable regulations
ficulty, must be instructed and trained by the cus- are complied with, even if they are not shown or
tomer. implied in the graphics, animations and videos pro-
▪ The customer is to ensure that the information mate- vided.
rials provided by Doka (e.g. User Information book- ▪ Individual sections contain further safety
lets, Instructions for Assembly and Use, Operating instructions and/or special warnings as applica-
Instruction manuals, plans etc.) are up to date and ble.
available to all users, and that they have been made
aware of them and have easy access to them at the
usage location. Planning
▪ In the relevant technical documentation and form-
work utilisation plans, Doka shows the workplace ▪ Provide safe workplaces for those using the form-
safety precautions that are necessary in order to use work (e.g. for when it is being erected/dismantled,
the Doka products safely in the usage situations modified or repositioned etc). It must be possible to
shown. get to and from these workplaces via safe access
In all cases, users are obliged to ensure compliance routes!
with national laws, standards and regulations ▪ If you are considering any deviation from the
throughout the entire project and to take appropriate details and instructions given in this booklet, or
additional or alternative workplace safety precau- any application which goes beyond those
tions where necessary. described in the booklet, then revised static cal-
culations must be produced for checking, as well
as supplementary assembly instructions.
Hazard assessment
▪ The customer is responsible for drawing up, docu- Regulations; industrial safety
menting, implementing and continually updating a
hazard assessment at every job-site. ▪ All laws, Standards, industrial safety regulations and
This booklet serves as the basis for the site-specific other safety rules applying to the utilisation of our
hazard assessment, and for the instructions given to products in the country and/or region in which you
users on how to prepare and utilise the system. It are operating must be observed at all times.
does not substitute for these, however.
▪ If a person or object falls against, or into, the side-
guard component and/or any of its accessories, the
component affected may only continue in use after it
has been inspected and passed by an expert.

4 999778002 - 04/2023
User Information Dokaflex table Introduction

Rules applying during all phases of Assembly


the assignment
▪ The equipment/system must be inspected by the
customer before use, to ensure that it is in an accept-
▪ The customer must ensure that this product is able condition. Steps must be taken to exclude com-
erected and dismantled, reset and generally used for ponents that are damaged, deformed, or weakened
its intended purpose in accordance with the applica- due to wear, corrosion or rot (e.g. fungal decay).
ble laws, standards and rules, under the direction
and supervision of suitably skilled persons.
▪ Using our safety and formwork systems together
with those of other manufacturers can create risks
These persons' mental and physical capacity must
that may lead to injury and damage to property. This
not in any way be impaired by alcohol, medicines or
requires separate verification by the user.
drugs.
▪ Doka products are technical working appliances ▪ The equipment/system must be assembled and
erected in accordance with the applicable laws,
which are intended for industrial / commercial use
standards and rules by trained customer personnel
only, always in accordance with the respective Doka
whilst maintaining any applicable safety inspections
User Information booklets or other technical docu-
that may be required.
mentation authored by Doka.
▪ The stability and load-bearing capacity of all compo- ▪ It is not permitted to modify Doka products; such
modifications constitute a safety risk.
nents and units must be ensured during all phases of
the construction work!
▪ Do not step on or apply strain to cantilevers, clo- Closing the formwork
sures, etc. until suitable measures to ensure their
stability have been correctly implemented (e.g. by
tie-backs). ▪ Doka products and systems must be set up so that
▪ Strict attention to and compliance with the functional all loads acting upon them are safely transferred!
instructions, safety instructions and load specifica-
tions are required. Non-compliance can cause acci-
dents and severe injury (risk of fatality) and consid-
Pouring
erable damage to property.
▪ Sources of fire in the vicinity of the formwork are pro- ▪ Do not exceed the permitted fresh-concrete pres-
hibited. Heaters are permissible only when used cor- sures. Over-high pouring rates overload the form-
rectly and situated a correspondingly safe distance work, cause greater deflection and risk breakage.
from the formwork.
▪ Customer must give due consideration to any and all
Stripping the formwork
effects of the weather on the equipment and regards
both its use and storage (e.g. slippery surfaces, risk
of slipping, effects of the wind, etc.) and implement ▪ Do not strip out the formwork until the concrete has
appropriate precautionary measures to secure the reached sufficient strength and the person in charge
equipment and surrounding areas and to protect has given the order for the formwork to be stripped
workers. out!
▪ All connections must be checked at regular intervals ▪ When stripping out the formwork, never use the
to ensure that they are secure and in full working crane to break concrete cohesion. Use suitable tools
order. such as timber wedges, special pry-bars or system
In particular threaded connections and wedged con- features such as Framax stripping corners.
nections have to be checked and retightened as nec- ▪ When stripping out the formwork, do not endanger
essary in accordance with activity on the jobsite and the stability of any part of the structure, or of any
especially after out-of-the-ordinary occurrences (e.g. scaffolding, platforms or formwork that is still in
after a storm). place!
▪ It is strictly forbidden to weld Doka products – in par-
ticular anchoring/tying components, suspension
components, connector components and castings
etc. – or otherwise subject them to heating.
Welding causes serious change in the microstruc-
ture of the materials from which these components
are made. This leads to a dramatic drop in the failure
load, representing a very great risk to safety.
It is permissible to cut individual tie rods to length
with metal cutting discs (introduction of heat at the
end of the rod only), but it is important to ensure that
flying sparks do not heat and thus damage other tie
rods.
The only articles which are allowed to be welded are
those for which the Doka literature expressly points
out that welding is permitted.

999778002 - 04/2023 5
Introduction User Information Dokaflex table

Transporting, stacking and storing Symbols used


▪ Observe all country-specific regulations applying to The following symbols are used in this document:
the handling of formwork and scaffolding. For system
formwork the Doka slinging means stated in this DANGER
booklet must be used – this is a mandatory require- This is a notifier drawing attention to an
ment. extremely dangerous situation in which non-
If the type of sling is not specified in this document, compliance with this notifier will lead to death
the customer must use slinging means that are suit- or severe, irreversible injury.
able for the application envisaged and that comply
with the regulations.
▪ When lifting, always make sure that the unit to be WARNING
lifted and its individual parts can absorb the forces This is a notifier drawing attention to a dan-
that occur. gerous situation in which non-compliance
▪ Remove loose parts or secure them so that they can- with this notifier can lead to death or severe,
not slip out of position and drop. irreversible injury.
▪ When lifting formwork or formwork accessories with
a crane, no persons must be carried along, e.g. on
working platforms or in multi-trip packaging. CAUTION
▪ All components must be stored safely, following all This is a notifier drawing attention to a dan-
the special Doka instructions given in the relevant gerous situation in which non-compliance
sections of this document! with this notifier can lead to slight, reversible
injury.
Maintenance
NOTICE
▪ Only original Doka components may be used as This is a notifier drawing attention to a situa-
spare parts. Repairs may only be carried out by the
tion in which non-compliance with this noti-
manufacturer or authorised facilities.
fier can lead to malfunctions or damage to
property.
Miscellaneous
The weights as stated are averages for new material; Instruction
actual weights can differ, depending on material toler- Indicates that actions have to be performed
ances. Dirt accretions, moisture saturation, etc. can by the user.
also affect weight.
We reserve the right to make alterations in the interests
of technical progress. Sight-check
Indicates that you need to do a sight-check
to make sure that necessary actions have
Eurocodes at Doka been carried out.

The permissible values stated in Doka documents


(e.g. Fperm = 70 kN) are not design values (e.g. FRd = Tip
105 kN)! Points out useful practical tips.
▪ It is essential to avoid confusing permissible values
with design values!
▪ Doka documents will continue to state the permissi-
ble values. Reference
Allowance has been made for the following partial fac- Cross-references other documents.
tors:
▪ γF = 1.5
▪ γM, timber = 1.3
▪ γM, steel = 1.1
▪ kmod = 0.9
Consequently, all the design values for an EC design
calculation can be determined from the permissible val-
ues.

6 999778002 - 04/2023
User Information Dokaflex table Introduction

Services
Support in every stage of the project High performance, in all stages of the project

▪ Project success assured by products and services


from a single source.
▪ Competent support from planning through to assem-
bly directly on site. Operations Construction Project close-
Tender
scheduling work out
Project assistance from start to finish
Every single project is unique and calls for individual- Engineering
ised solutions. When it comes to the forming opera- ▪ Execution planning
tions, the Doka team can help you with its consulting, ▪ Cycle planning
planning and ancillary services in the field, enabling ▪ Structure modelling/3D-planning
you to carry out your project effectively, safely and reli- ▪ Assembly drawings
ably. Doka assists you with individual consulting ser- ▪ Statical calculation
vices and customised training courses. ▪ Concremote

Efficient planning for a safe project sequence Consulting and training

Efficient formwork solutions can only be developed


▪ Project processing on-site

economically if there is an understanding of project


▪ Formwork instructor

requirements and construction processes. This under-


▪ Training & consulting

standing is the basis of Doka engineering services.


Process optimisation

Optimise construction workflows with Doka


▪ Concremote (country-spe-
cific)
Doka offers special tools that help you in designing ▪ myDoka
transparent processes. This is the way to speed up ▪ Planning software
pouring processes, optimise inventories and create ▪ Yard management
more efficient formwork planning processes.
Pre-assembly and assembly
Custom formwork and on-site assembly ▪ Pre-assembly service
To complement its system formwork range, Doka ▪ Pre-assembly on site service
offers customised formwork units. And specially
trained personnel assemble load-bearing towers and Logistics
formwork on site. ▪ Organisation of transport & freight

Just-in-time availability Rental and reconditioning service


Formwork availability is a crucial factor in realising ▪ Rental service
your project on time and on budget. The worldwide ▪ Formwork returns
logistics network puts the necessary formwork quanti- ▪ Reconditioning & service fixed rates
ties on site at the agreed time.
Digital Services
Rental and reconditioning service for higher productivity in construction
The formwork material needed for any particular pro- From planning to completion of construction -
ject can be rented from Doka’s high-performing rental with our digital services we want to set the
park. Doka Reconditioning cleans and overhauls both pace for boosting productivity in construction.
client-owned equipment and Doka rental equipment. Our digital portfolio includes solutions for plan-
ning, procuring and managing to performing
on site. Learn more about our digital offer at
doka.com/digital.

999778002 - 04/2023 7
System description User Information Dokaflex table

System description
Dokaflex table – the tried-and-tested high-speed tableform
Doka floor props Eurex
EN 1065-compliant floor prop

9720-214-01
Their high load-bearing capacity is complemented by
many practical details making them very easy to han-
dle:
▪ numbered pegging holes for height adjustment
▪ elbowed fastening clamps, reducing the risk of injury
9720-215-01 and making the props easier to operate
Dokaflex tables are easy and practical to set up and ▪ special geometry of the thread makes the prop eas-
can be shifted and adapted very quickly. This makes ier to release even under high load
them a cost-effective and efficient way of carrying out The flexurally rigid link with the tableform superstruc-
large-area slab projects. ture increases the load-bearing capacity of the floor
Dokaflex tables are fully combinable with Dokamatic props:
tables. ▪ permitted capacity of Eurex 20 top:
▪ assembled from components of the Dokaflex system - when completely extended: 30 kN
▪ 4 standard formats with an underlying 'grid' logic: - when inserted by min. 30 cm: 36.7 kN
- 2.50 x 4.00 m ▪ permitted capacity of Eurex 30 top: 41.2 kN
- 2.50 x 5.00 m ▪ permitted capacity of Eurex 20 LW: 30 kN
- 2.00 x 4.00 m
- 2.00 x 5.00 m Follow the directions in the 'Floor
▪ tableform faced with 3S top formwork sheets, 21 or props Eurex top' or 'Floor props Eurex 20 LW'
27 mm User Information booklet.
▪ for slab heights up to 5.90 m
▪ can start to pay off after as few as 2 re-use cycles
WARNING
▪ custom formats are also possible where needed
▪ site-ready, custom-format Dokaflex tables can be ➤ It is not permitted to use Eurex floor props
supplied by the Doka Pre-assembly Service 20 top 700 on Doka tableforms.
▪ wedge-lock makes quick and easy work of attaching
and detaching props
▪ low stacking height when transported and stored
▪ safe, fast shifting devices – save time and money
▪ forming can continue seamlessly into infill zones and
closure gaps
▪ the technically perfected individual components
make a big contribution to higher speeds
▪ commissioning quantities are easy to tailor to the
construction schedule – a weekly cycle is no problem

8 999778002 - 04/2023
User Information Dokaflex table System description

System dimensions
Dokaflex table 27mm

Dokaflex table 2.50x4.00m Dokaflex table 2.50x5.00m


10.0 2x38.8 4x56.3 2x38.8 10.0 10.0 2x50.0 2x46.7 2x46.6 2x46.7 2x50.0 10.0

7.5
7.5
47.5

47.5
150.0

150.0

230.0
230.0
47.5

47.5
9778-210-07

7.5
7.5
9778-210-08
225.0 280.0

Dokaflex table 2.00x4.00m Dokaflex table 2.00x5.00m


10.0 2x38.8 4x56.3 2x38.8 10.0 10.0 2x50.0 2x46.7 2x46.6 2x46.7 2x50.0 10.0
7.5

7.5
25.0

25.0
180.0

180.0
145.0

145.0
25.0

25.0

9778-210-05
7.5

9778-210-06

7.5
225.0 280.0

Dokaflex table 21mm

Dokaflex table 2.50x4.00m Dokaflex table 2.50x5.00m


10.0 2x38.8 4x56.3 2x38.8 10.0 10.0 2x45.0 6x50.0 2x45.0 10.0

7.5
7.5
47.5

47.5
150.0

150.0

230.0
230.0
47.5

47.5

7.5

9778-210-03 9778-210-04
7.5

225.0 300.0

Dokaflex table 2.00x4.00m Dokaflex table 2.00x5.00m


10.0 2x38.8 4x56.3 2x38.8 10.0 10.0 2x45.0 6x50.0 2x45.0 10.0
7.5

7.5
25.0

25.0
180.0

180.0
145.0

145.0
25.0

25.0
7.5

9778-210-01 9778-210-02
7.5

225.0 300.0

999778002 - 04/2023 9
System description User Information Dokaflex table

Instructions for assembly and use (Method statement)


Dokaflex tables can cover a wide area of practical appli- Pre-assembly
cations.
Their flexible design enables them to be combined in
➤ While the tables are still on the stack, attach an edge
very versatile ways.
strip (F) to each table that is going to be placed
This means that in some projects, they will be put directly against a wall of the building.
together differently, and a different sequence of opera-
tions will be needed, from the scheme shown here (e.g.
for sloping walls).

CAUTION F
➤ Dokaflex tables with floor props may only be
used to form horizontal slabs.
➤ It is forbidden to use Dokamatic tables in
inclined situations.
➤ Never place tables with floor props on top of
one another.

CAUTION
Before stepping onto the tables, observe 9778-200-01
the following points:
➤ Horizontal stability must be ensured (e.g. by ➤ Also pre-install the sideguards for edge tables while
back-tying the edge tables, by fixing the the tables are still on the stack (see the section
tables to the structure, by joining them into headed 'Tables around edges of slab'). Where
one continuous forming area). needed, attach side safety railings.
➤ If no fall protection is in place (e.g. during
formwork set-up or stripping), a personal
fall-arrest system (PFAS) must be used
(e.g. safety harness).
The FreeFalcon mobile fall protection mast
permits a secure attachment point to be cre-
ated for the safety harness.

User instruction prior to use of the FreeFalcon


is mandatory.
Follow the directions in the 'FreeFalcon' Oper-
ating Instructions.

NOTICE
All necessary traffic routes must be prepared
at the site!

Transporting / handling the panels 9778-201-01

➤ For offloading panels from a truck, or lifting them on-


site a stack at a time, use the Dokamatic lifting strap
13.00m (see the section headed 'Transporting,
stacking and storing').

10 999778002 - 04/2023
User Information Dokaflex table System description

Closing the formwork ➤ Bring further tables to the usage location in the same
way.
➤ Use the Dokamatic lifting strap 13.00m to lift the
table superstructure onto the DoKart plus, or onto
suitable temporary shoring (see the section headed
'Transporting, stacking and storing').
➤ If necessary, adjust the position and number of the
table heads (see the section headed 'Adapting to dif-
ferent slab thicknesses').
➤ Mount the floor props (see the section headed
'Mounting the floor props').

9778-204-01

9778-202-01

➤ Bring the table to its usage location using the Doka-


matic lifting strap 13.00m or the DoKart plus. Then
raise it to its intended operational height, extend the
floor props, and adjust the height.
If possible, start by putting up the first table in one
corner of the building – with the pre-mounted edge
strip facing the wall.
➤ Fix the first table to the structure (e.g. with braces,
Lashing strap 5.00m (A) or in-place solutions using
e.g. the tie-holes in the wall).
9778-205-01

9778-203-01

999778002 - 04/2023 11
System description User Information Dokaflex table

CAUTION
Risk of edge tables toppling over!
(due to edge props that have been relocated
towards the inside, stop-end formworks, down-
stand beams)
➤ Secure all edge tables by tying back (A)
every primary beam in the inner cantilever
zone of the table.
➤ Do not release the table from the shifting
device until tie-backs are fixed to prevent tip-
over.
➤ Also applies when setting down tables or
putting them into temporary storage.

9778-245-01

For details of the tie-back, see the section


headed 'Tie-back solutions'.

12 999778002 - 04/2023
User Information Dokaflex table System description

➤ Insert standard strips between the tables, and nail Stripping and repositioning the
where needed (see the section headed 'Adaptation
to building layout'). formwork

NOTICE
As well as the instructions given here, you
must follow the instructions in the section
headed 'Reshoring props, concrete technol-
ogy and stripping out'.
➤ Check the concrete strength.
➤ Take the load off the floor props of the tables, and
lower them approx. 5 cm.

The T-ledge makes it easier to remove the


tableforms.
T-ledges are only needed in the area where
formwork removal is going to begin.

9767-299-01
a

9767-297-01
a ... max. 15 mm

➤ Form the closure zones (see the section headed


'Adaptation to building layout').
➤ Form the slab stop-ends (see the section headed ➤ Remove the standard strips and closures (see the
'Slab stop-ends'). section headed 'Adaptation to building layout').
➤ Spray the formwork sheeting with release agent.
➤ Place the reinforcement.

Pouring
➤ Before pouring, recheck all floor props.
▪ The fastening clamp (A) has to be pushed
all the way into the floor prop.
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

A
9778-209-01

98017-202-01

To protect the surface of the form-facing, we recom-


mend using a vibrator with a protective rubber cap.

999778002 - 04/2023 13
System description User Information Dokaflex table

➤ Position the DoKart plus beneath the middle of the


table.
➤ Extend the lifting tower until the table is supported on
the distribution beams of the DoKart plus.
➤ Push the floor props all the way in and, with the
DoKart plus, lower the table until it is 10 cm clear of
the ground.
a

9778-202-02

a ... max. 10 cm ground clearance


➤ Reposition the table (see the sections headed 'Hori-
zontal repositioning / travelling', 'Vertical reposition-
ing with transport forks' and 'Table Lifting System
TLS').

Reshoring

NOTICE
As well as the instructions given here, you
must follow the instructions in the section
headed 'Reshoring props, concrete technol-
ogy and stripping out'.
➤ Before pouring the next floor-slab (i.e. above the one
that has just been stripped), put up reshoring props.

14 999778002 - 04/2023
User Information Dokaflex table System description

Adaptation to building layout


The formwork system can be adapted to the building in the direction of the secondary
layout in the following ways:
▪ combining different sizes of table beams
▪ grid logic (arranging the tables lengthways and
crossways) The sheet-covered area is 10 cm less than the system
▪ closure zones with fitting-boards dimension on both long sides of the table. The project-
ing secondary beam acts as a support for the strips of
formwork sheeting.
D A B 9778-246-02

a
A B
10 b 10
A a
C
Dimensions in cm
a ... System width of the table (200 cm or 250 cm)
9767-275-01 b ... a - 20 cm (180 cm or 230 cm)
a A Support for strip of formwork sheeting
a ... 4.0 m / 5.0 m B Sheet-covered area
C Secondary beam
A e.g. Dokaflex table 2.00 x 4.00m or 2.50 x 5.00m
B Typical zone (standard strip)
C Wall junction (standard strip) Typical zone
D Closure zone (fitting-board)
Between the tables and at wall junctions, it is always
▪ table sizes and table shapes adapted to the project standard strips that are inserted.
- e.g. greater length (A) , one side slanted (B) etc.
Standard strip (20 cm) between the tables
Custom tables (simplified illustration): 20.0

9767-272-01

B
Standard strip (9.7 cm) at wall junctions
9778-247-01
9.7

Note:
For assembling custom tables, consult your Doka tech-
nician!

9767-278-01

999778002 - 04/2023 15
System description User Information Dokaflex table

Closure zone Forming and stripping closures with insertion


beams
Instead of the standard strips, a fitting-board of variable
width is inserted between the tables.
Location of insertion beams:
Note:
The width of the fitting-board needed is always 20 cm
A
larger than the actual closure dimension 'x'.

a
Fitting-board (x + 20 cm) between the tables A
s
x
A
B C B

9767-272-02

A D A
s ... Width of fitting-board (x + 20 cm)
x ... Actual closure dimension

9767-238-01
The type of closure is selected depending on the slab
A
thickness and on the necessary closure width 'x' (see
the section headed "Structural design"). a ... max. spacing of secondary beams of the Dokaflex table
A Insertion beam 1.95m (on 2.00m wide tables)
Option 1: fitting-board only Insertion beam 2.45m (on 2.50m wide tables)
x B Dokaflex table
C Fitting-board
D Joint where the fitting-boards abut

9778-248-01
Note:
At the ends of the tables, the insertion beams are
placed as close as possible to the edge.

Joint where the fitting-boards abut (D) :


Option 2: fitting-board with insertion beam, with no ▪ in the direction of the primary beams: an addi-
additional propping tional insertion beam is necessary.
x ▪ in the direction of the secondary beams: over the
raised support surface (E) of the insertion beam. If
this is not possible, fit the insertion beam with its
raised support surface facing downwards, and
9778-248-02 wedge it up on the table waling.

D E

Option 3: fitting-board with insertion beam and 9767-296-01


additional propping
x

9778-248-03

16 999778002 - 04/2023
User Information Dokaflex table System description

Closing the formwork:


CAUTION
➤ Push insertion beams into the tableforms alongside
Before stepping onto the tables, observe the closure zone, flush with the secondary beams.
the following points:
➤ Horizontal stability must be ensured (e.g. by
back-tying the edge tables, by fixing the
tables to the structure, by joining them into
one continuous forming area).
➤ If no fall protection is in place (e.g. during
formwork set-up or stripping), a personal
A
fall-arrest system (PFAS) must be used
(e.g. safety harness).

The FreeFalcon mobile fall protection mast

9778-244-01
permits a secure attachment point to be cre-
ated for the safety harness.
A Insertion beam
User instruction prior to use of the FreeFalcon
is mandatory.
Follow the directions in the 'FreeFalcon' Oper- ➤ Put up tables opposite the closure zone.
ating Instructions.

Use a mobile scaffold tower (e.g. Working scaffold B


Modul) or a platform stairway for setting up and strip-
ping the formwork.
NOTICE B

When using the Platform stairway 0.97m for


vertical access, note the following:
▪ Minimum distance a from drop-off edge:
2.00 m
9778-244-02

B Dokaflex table

➤ Pull each insertion beam across the closure zone (1)


98033-468-01 and turn it into the upright (2).

2
9778-244-03

➤ Place fitting-boards over the closure zone, and nail


where needed.

9778-208-02

999778002 - 04/2023 17
System description User Information Dokaflex table

Stripping and repositioning the formwork: Closure zone

CAUTION
Note:
Risk of insertion beams falling out
The closure zone should be supported by a centrally
➤ Do not leave insertion beams with a length placed floor prop - this has no implications regarding
of 1.95m inside 2.50m wide tables when the dimensioning of the table. Otherwise, statical verifi-
these are repositioned! cation is required.
➤ Take the load off the floor props of the tables, and
lower the tables approx. 5 cm on one side of the clo- b b
sure zone.

A
9778-249-01 B

b ... max. 10 cm
9778-244-04 A Doka beam H20
B Squared timber 60x120 mm (site-provided)
➤ Turn the insertion beams on their sides (1) and push
them into the tableform (2).
b x b

9778-249-02

b ... max. 10 cm
x ... max. closure
(see the dimensioning table 'Form-facing + closure option 1')
9778-244-03

Combining tables in the direction of


➤ Take off the fitting-boards. the secondary beams and of the
➤ Lower the remaining tables. primary beams
➤ Reposition the tables together with the insertion
beams.
The insertion beams are available for use again s
straight away at the new location.

in the direction of the primary beams A


9778-249-03 B

Typical zone
s ... Dimension of sheet
A Doka beam H20
B Squared timber 60x120 mm (site-provided)

Note:
The beam (A) must be pre-mounted!
9778-246-01

A A

A Dokaflex table

18 999778002 - 04/2023
User Information Dokaflex table System description

Adapting to different slab thicknesses


The tables can be adapted to take account of the Intermediate head DF
required slab thickness by installing extra intermediate
props:
▪ with Table head 30
▪ with Intermediate head DF
▪ with Supporting head H20 DF
NOTICE
For mounting intermediate props on a
Put up the intermediate props so that they double primary beam
force-fit. It is not allowed to make some props
higher than others! NOTICE
▪ An increase in the load-bearing capacity of
Note: the floor prop, and moment transfer such as
If the slab thicknesses vary, intermediate props can with the table head, are not possible here!
also be installed temporarily. ▪ The main props of the table (at least 4 of
them) must always be attached with a table
head!
Positioning the floor props
WARNING
2 floor props per primary beam
Risk of intermediate props dropping out
(standard table) when table is lifted
➤ Intermediate props that are attached by an
Intermediate head DF and that are not dis-
9720-325-01

mounted must be pulled in sufficiently far.

3 floor props per primary beam


(1 intermediate prop in mid-span)
9720-326-01

B
A
9720-216-01

Table head 30

A Intermediate head DF
B Doka beam H20

Note:
For mounting the Table heads 30, see the section
headed "Mounting the table heads"!

999778002 - 04/2023 19
System description User Information Dokaflex table

Assembly Supporting head H20 DF


➤ Place the Intermediate head DF on the floor prop
and secure it with the integral spring-steel stirrup.

1 2 3
For mounting intermediate props on a
single primary beam
NOTICE
▪ An increase in the load-bearing capacity of
the floor prop, and moment transfer such as
with the table head, are not possible here!
▪ The main props of the table (at least 4 of
them) must always be attached with a table
head!

9778-211-01
WARNING
Risk of intermediate props dropping out
➤ Push the Intermediate head DF up between the dou- when table is lifted
ble primary beams, turn it 90° and pull it down. ➤ Intermediate props with a Supporting head
➤ Twist the floor prop to fix it firmly onto the double pri- H20 DF, and props that are only secured
mary beams. against tipping over, must be removed
before the table is lifted.
1 2 3

A
B
9768-215-01

A Supporting head H20 DF


9720-264-01

B Doka beam H20


C Bore in the Supporting head
(for fixing with chipboard screw 4x35)
▪ The fastening clamp (A) has to be pushed
all the way into the floor prop.
Assembly
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.
➤ Place the Supporting head H20 DF on the floor prop
and secure it with the integral spring-steel stirrup.

A
1 2 3

98017-202-01
9767-233-01

➤ Put up the intermediate props.


▪ The fastening clamp (A) has to be pushed
all the way into the floor prop.
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

98017-202-01

20 999778002 - 04/2023
User Information Dokaflex table Assembly

Assembly
Assembling the table superstructure

The professionals from the Doka "Ready-to- Mount the remaining secondary beams
Use Service" plan and assemble site-ready ➤ Place the remaining secondary beams onto the pri-
and custom formworks exactly to your spec- mary beams (use a template if necessary).
ifications.

For a clean concrete finish and for the Dokaflex tables G


to function at their best, it is important to assemble them
correctly and precisely.
Assembly floor with stop bars
➤ Prepare a flat assembly floor (wooden drawing floor).
➤ Attach stop-bars for the table heads, primary beams
and secondary beams. 9720-235-01

Mount the table heads, primary and secondary G Secondary beam


beams
➤ Insert the table heads between the prepared stop-
bars. ➤ Screw the secondary beams to the primary beams
diagonally, using rack screws 6x80mm.
➤ Place the primary beams into the table heads and
push them up against the stop-bar. Mount the formwork sheets
➤ Lay the secondary beams centrally, directly over the ➤ Decide how the sheets are to be arranged. If neces-
table heads, and push them up against the stop-bar. sary, mark the position of the first row of sheets with
a chalk line.
B ➤ Lay the formwork sheets and pull them tight with the
C
Strip tensioner B 5.00m.
G ➤ Nail the sheets to the secondary beams with ring
nails 3.1x60mm.
A
F H
D E
9720-234-01

A Assembly floor
B Stop-bar for primary beams
C Stop-bar for secondary beams
D Stop-bar for table head
E Table head 9720-236-01

F Primary beam H Formwork sheet


G Secondary beam

The Lifting hook DF, or Dokamatic lifting straps


➤ Bolt the table heads to the secondary beams (see 13.00 m, are ideal for lifting the pre-assembled units
the section headed "Mounting the table heads"). away from the assembly area.

999778002 - 04/2023 21
Assembly User Information Dokaflex table

Mounting the table heads


The Table head 30 firmly links the Doka formwork The Dokaflex tables include secondary beams
beams H20 to the Doka floor props Eurex. with the extra holes needed for the Table head
30. This means that they can quickly and eas-
ily be modified for 6 floor props.
with Connection unit DF 20/30
for longer assignments involving high numbers of
repeat uses.
Tools needed:
▪ Centre bit DF 30
▪ Box nut 19 1/2" L
▪ Reversible ratchet 1/2"

9720-320-01

with Beam screw S 8/60


Tools needed:
▪ Wood drill, diam. 10 mm
9720-230-01

▪ Box nut 13 1/2"


▪ Reversible ratchet 1/2"
2 Connection units DF 20/30 are needed for each
Table head 30.

b
9720-229-01
a

4 Beam screws S8/60 are needed for each Table head


30.

9720-299-01 9720-300-01 d

a ... 210 mm
b ... 396 mm
c ... 4 to 12 mm b
e
Use the Centre bit DF 30 to drill the holes in the webs.
a
d

9720-301-01

d ... diam. 30 mm
9720-297-01 9720-298-01

a ... 210 mm
b ... 51 mm
c ... 4 to 12 mm
d ... 39.6 mm
e ... approx. 30mm
A Drilling template DF is available on request, to speed
up the job of drilling the holes in the beams.

22 999778002 - 04/2023
User Information Dokaflex table Assembly

Table head for single primary beam

Converting the Table head 30


Although designed as standard for double primary
beams, the Table head 30 can easily be converted for
use with a single primary beam by using different holes
for its two M16x45 hexagon bolts.

Position of bolts for Position of bolts for


double primary beam single primary beam

9720-296-01 9720-295-01

Table head 20
Where Dokaflex tables are assembled with single pri-
mary beams, it is also possible to use the Table head
20 instead of the Table head 30.

Beam screw S 8/60 Connection unit DF 20/30

9720-294-01 9720-293-01

999778002 - 04/2023 23
Assembly User Information Dokaflex table

Mounting the floor props


➤ Tighten the wedge with the hammer.

9720-218-01
9720-215-01 NOTICE
▪ Having the outer tube at the top increases
stability
▪ To make it easier to get at the adjusting nut,
A Table head 30 it is also possible to have the outer tube at
B Floor props Eurex 20 top, Eurex 20 LW or Eurex 30 top the bottom.
▪ Where the floor-slab height is 3.50 m and
The floor prop is quickly and securely fixed onto the upward, secure the wedge with a spring cot-
Table head 30 with the aid of the double wedge. ter 5mm, as at this height and above it is dif-
➤ Pull back the wedge of the Table head 30 and insert ficult to do a sight-check.
the prop.
▪ The fastening clamp (A) has to be pushed
all the way into the floor prop.
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

98017-202-01

Note:
Where the Doka floor prop Eurex 20 top 550 is used,
9720-217-01

the Table head 30 can only be attached to the inner


tube.

24 999778002 - 04/2023
User Information Dokaflex table Assembly

999778002 - 04/2023 25
Structural design User Information Dokaflex table

Structural design
Note: Max. slab thickness 'd'
Max. closure 'x' [cm]
In accordance with EN 12812, a service load of [cm]
0.75 kN/m2 and a variable load of 10% of a massive Number of floor props Form-facing and

Type of prop
Table format
per table waling closure options
concrete floor-slab, totalling at least 0.75 kN/m2, but no
more than 1.75 kN/m2, are allowed for (assuming a
2 3 Opt. 1 Opt. 2 Opt. 3
fresh-concrete density of 2500 kg/m3).
37 40 0 (= standard strip)
The tables can be fitted with different formwork sheets. 35 38 10 10 20
The structural design is therefore split in two parts: 33 36 20 20 40

(top or LW)
Eurex 20
▪ Supporting construction with floor props 31 34 30 30 60
29 32 40 40 80
▪ Form-facing and closure options 28 30 50 50 —
27 29 60 60 —

2.00x5.00
26 28 60 70 —
Supporting construction with floor 25 27 60 80 —
46 52 0 (= standard strip)
props 44 50 10 10 20
42 48 20 20 40

Eurex 30
40 46 30 30 60
37 44 40 40 80
see the section headed 'System dimen- 35 42 50 50 —
Table format 33 40 60 60 —
sions'
Number of floor props see the section headed 'Adapting to differ- 32 38 60 70 —
per primary beam ent slab thicknesses' 31 36 60 80 —
45 50 0 (= standard strip)
Form-facing and clo- to be selected depending on the slab thick- 43 47 10 10 20
sure options ness (see ‘Form-facing and closure (top or LW)
41 45 20 20 40
options’ in the ‘Structural design’ section)
Eurex 20

40 43 30 30 60
38 41 40 40 80
Max. slab thickness 'd' 36 39 50 50 —
Max. closure 'x' [cm]
[cm] 34 37 60 60 —
2.00x4.00

Number of floor props Form-facing and 32 36 60 70 —


Type of prop
Table format

per table waling closure options 31 35 60 80 —


60 70 0 (= standard strip)
57 66 10 10 20
2 3 Opt. 1 Opt. 2 Opt. 3 54 63 20 20 40
Eurex 30

51 60 30 30 60
30 32 0 (= standard strip) 49 58 40 40 80
29 31 10 10 20 47 55 50 50 —
28 30 20 20 40 45 53 60 60 —
(top or LW)
Eurex 20

27 29 30 30 60 43 51 60 70 —
25 27 40 40 80 42 49 60 80 —
24 26 50 50 —
23 25 60 60 —
Form-facing and closure options
2.50x5.00

22 24 60 70 —
21 23 60 80 —
35 42 0 (= standard strip)
33 40 10 10 20
32 39 20 20 40 Note:
Eurex 30

31 38 30 30 60
30 36 40 40 80 For detailed information on the formwork sheet and clo-
29 34 50 50 — sure options, see the section headed 'Adaptation to
28 33 60 60 — building layout'.
27 32 60 70 —
26 31 60 80 —
40 42 0 (= standard strip) Notes on dimension (x):
38 40 10 10 20 ▪ The influence of the closure on the table will vary
36 38 20 20 40 depending on which closure option (1 to 3) has been
(top or LW)
Eurex 20

35 37 30 30 60 selected.
33 35 40 40 80
32 34 50 50 — ▪ The relevant table and the number of floor props
31 33 60 60 — needed is selected from the table 'Supporting con-
2.50x4.00

30 32 60 70 — struction with floor props', with reference to the


29 31 60 80 —
50 55 0 (= standard strip)
values 'x' and the slab thickness 'd'.
48 53 10 10 20 ▪ The width of the fitting-board needed is always
46 51 20 20 40 20 cm larger than the actual closure dimension 'x'.
Eurex 30

44 49 30 30 60
42 47 40 40 80
40 45 50 50 —
39 43 60 60 —
38 42 60 70 —
37 41 60 80 —

26 999778002 - 04/2023
User Information Dokaflex table Structural design

Formwork sheet with no closure (standard strip)


Max. slab thickness 'd' [cm] Max. closure 'x' [cm]
Formwork sheet

DokaPly eco

DokaPly eco
d

Dokaplex

Dokaplex
18mm
21mm

27mm

21mm

18mm

21mm
Standard strip

3-SO

3-SO
9767-272-01

50 85 70 95 35 50 0

Formwork sheet + closure option 1


Max. slab thickness 'd' [cm] Max. closure 'x' [cm]
Formwork sheet

DokaPly eco

DokaPly eco
Dokaplex

Dokaplex
Fitting-board only

18mm
21mm

27mm

21mm

18mm

21mm
3-SO

3-SO
(Opt. 1)

x 35 65 60 90 30 45 5
25 50 55 75 25 40 10
20 40 50 65 25 35 15
d

— 35 45 60 20 30 20
— 25 40 55 — 25 25
9767-221-01 — 20 35 45 — 20 30
— — 30 40 — 20 35
— — 25 35 — — 40
— — 25 35 — — 45
— — 20 30 — — 50
— — — 25 — — 55
— — — 25 — — 60

Formwork sheet + closure option 2


Max. slab thickness 'd' [cm] Max. closure 'x' [cm]
Formwork sheet
Fitting-board with inser-
DokaPly eco

DokaPly eco
Dokaplex

Dokaplex

tion beam, with no addi-


21mm
21mm

27mm

18mm

18mm

21mm
3-SO

3-SO

x tional propping
(Opt. 2)
d

60 95 60 95 40 70 20
60 95 60 95 40 70 30
9767-224-01
50 / 351) 85 / 651) 60 95 25 45 40
35 65 / 401) 60 85 20 45 50
25 50 / 251) 55 70 — 40 60
— 40 50 55 — 35 70
— 35 45 45 — 30 80
Values apply only for tables covered with same-size sheeting 'wall-to-wall' (e.g. 60 cm wide) or with uniformly divided sheets (e.g. 30+30 cm) with
the insertion beam set in the middle.
1) Value for sheets not uniformly divided (e.g. 50+10 cm).

Formwork sheet + closure option 3


Max. slab thickness 'd' [cm] Max. closure 'x' [cm]
Formwork sheet
Fitting-board with inser-
DokaPly eco

DokaPly eco

x
Dokaplex

Dokaplex

tion beam and additional


21mm
21mm

27mm

18mm

18mm

21mm
3-SO

3-SO

propping
(Opt. 3)
d

60 95 60 95 40 70 20
60 95 60 95 40 70 30
50 / 351) 85 / 651) 60 95 25 45 40
35 65 / 401) 60 85 20 45 50
25 50 / 251) 55 70 — 40 60
9767-225-01
— 40 50 55 — 35 70
— 35 45 45 — 30 80
Values apply only for tables covered with same-size sheeting 'wall-to-wall' (e.g. 60 cm wide) or with uniformly divided sheets (e.g. 30+30 cm) with
the insertion beam set in the middle.
1) Value for sheets not uniformly divided (e.g. 50+10 cm).

999778002 - 04/2023 27
Tables around edges of slab User Information Dokaflex table

Tables around edges of slab


Dokaflex tables for the edge zones can be assembled
with the downstand-beams, stop-end formwork and CAUTION
sideguards already integrated into the tables. Risk of edge tables toppling over!
If possible, pre-mount the attachments to the (due to edge props that have been relocated
table elements on the floor, while these are still towards the inside, stop-end formworks, down-
on the stack. stand beams)
➤ Secure all edge tables by tying back (A)
every primary beam in the inner cantilever
zone of the table.
➤ Do not release the table from the shifting
device until tie-backs are fixed to prevent tip-
over.
➤ Also applies when setting down tables or
putting them into temporary storage.

9720-227-01

9778-245-01

For details of the tie-back, see the section


headed 'Tie-back solutions'.

28 999778002 - 04/2023
User Information Dokaflex table Tables around edges of slab

Tie-back solutions

NOTICE Tie-back from the Table head 30


▪ When calculating the leg loads, allow for the ➤ Hook the Lashing strap 5.00m directly onto the Table
additional forces imposed by the back-stay!
head 30.
▪ Attach the back-stay in such a way that the
tableform is held in both directions and
secured against twisting.
▪ Direction of pull of the back-stay (A) always
90° to the tableform. Oblique pull is not per-
mitted!

90°

9778-216-01
A

with Lashing strap 5.00m and Doka


A Lashing strap 5.00m
express anchor 16x125mm
Tie-backs for high tableforms
Permitted tensile force per lashing strap: 10 kN
If necessary, two Lashing straps 5.00m can be joined
Follow the directions in the together to form a longer back-stay.
'Lashing strap 5.00m' User Information book-
NOTICE
let.
Only Lashing straps 5.00m with spring-
loaded locking flap may be used!
Tie-back using the Lifting hook DF

NOTICE
Do not exceed the max. permitted tensile force
of 3.0 kN of the Lifting hook DF!
➤ Hook the Lashing strap 5.00m onto the Lifting A
hook DF.
A

9767-359-01

A Lashing strap 5.00m (with spring-loaded locking flap)

A
9778-214-01

A Lashing strap 5.00m

999778002 - 04/2023 29
Tables around edges of slab User Information Dokaflex table

Anchoring in the ground with plumbing struts


➤ Prepare an anchorage point in the ground with the Using plumbing struts fitted with a U-head D, Dokaflex
Doka express anchor – hook in the lashing strap and tables can be fixed so that they are resistant to either
tension it. tensile or compressive forces.

B C

9767-258-02
9720-283-02
A Lashing strap 5.00m
B Doka express anchor A U-head D
B Plumbing strut
C Doka Express anchor 16x125mm
The Doka express anchor can be re-used many times
over.

Permitted load where fck,cube,current ≥ 10 N/mm2:


Fperm. = 10.0 kN (Rd = 15.0 kN)
(values apply to uncracked concrete)

Follow the Fitting Instructions!

Always perform a static check if other-make heavy-


duty dowels are used to fabricate anchorages in the
floor slab.
Follow the manufacturers' applicable fitting instruc-
tions.

30 999778002 - 04/2023
User Information Dokaflex table Tables around edges of slab

Edge table with no downstand beam


The floor prop (A) is located further towards the inside Handrail post T 1.80m
than on the standard table.
This leaves a sufficiently large area of table free to work
on beyond the stop-end.
Safety railings can be erected using e.g. the Handrail
post T 1.80m or Xsafe edge protection XP.
A

B
B

9778-223-01

9778-220-01
A Handrail post T 1.80m
B Protective grating or guard-rail boards (site-provided)
B Handrail post T 1.80m or Xsafe edge protection XP C Doka formwork beam

Required nuts & bolts etc.


▪ 2 hexagon screws M20x90
▪ 2 hexagon nuts M20
▪ 2 washers R22
(not included with product)
How to mount:
➤ Mount the Handrail post T 1.80m in the ready-drilled
holes in the beam.
(Can be used on both primary and secondary
beams)
➤ Fit on a Protective grating XP or guard-rail boards,
and fix them in place.

999778002 - 04/2023 31
Tables around edges of slab User Information Dokaflex table

Xsafe edge protection XP Handrail clamp S

Follow the directions in the 'Xsafe edge protec- For erecting sideguards on tables that project beyond
tion XP' User Information booklet. the slab-edge.
Follow the directions in the “Handrail clamp S”
Insertion adapter XP User information!

▪ Suitable for railing-heights of 1.20 m and 1.80 m.

A
B
C

D 9778-218-02

A Guard-rail board (site-provided)


9778-223-02
B Handrail clamp S
A Insertion adapter XP C Doka formwork beam
B Handrail post XP
How to mount:
C Protective grating or guard-rail boards (site-provided)
➤ Wedge the Handrail clamps firmly to the secondary
D Doka formwork beam
beams (clamping range 2 – 43 cm).
Required nuts & bolts etc. ➤ Secure the guardrail boards to the loops on the
▪ 2 hexagon screws M20x90 Handrail clamp S with one 28 x 65 nail per loop.
▪ 2 hexagon nuts M20
▪ 2 washers R22
(not included with product)
How to mount:
➤ Mount the Insertion adapter XP in the ready-drilled
holes in the beam.
(Can be used on both primary and secondary
beams)
➤ Working from below, push the Toeboard holder XP
0.60m onto the Handrail post XP 1.80m (not needed
when using the Protective grating XP).
➤ Push the Handrail post XP into the post-holding fix-
ture on the Insertion adapter XP until the locking
mechanism engages.
The locking mechanism must engage.

➤ Fit on a Protective grating XP or guard-rail boards,


and fix them in place.

32 999778002 - 04/2023
User Information Dokaflex table Tables around edges of slab

Slab stop-ends
with Framax universal corner waling with Universal end-shutter support
30cm

9778-219-01

9778-215-01

B
A
a
D
b

9767-369-01

E
Max. influence width: a
C 9778-219-02 for slab thickness of [cm]
How fastened: Configuration 20 25 30
4 nails 3.1x80 A 90 50 30
a ... 6 to 16 cm
b ... slab thickness max.40 cm 4 Spax screws 4x40
B 220 190 160
(fully threaded)
A Framax panel
B Framax universal corner waling
C Retaining plate 15.0
D Super-plate 15.0
E Tie-rod 15.0 approx. 70 cm long

Use a 20 mm diameter bit to drill the hole


through the form-ply.
Unneeded clamping holes should be closed
off on the site with Universal plugs R20/25.

Wherever possible, use tables in the same


way every time, e.g. always as edge tables -
this prevents holes being drilled in the tables
unnecessary.

999778002 - 04/2023 33
Tables around edges of slab User Information Dokaflex table

fastened with nails (configuration A) fastened with Spax screws (configuration B)

C
C E
B D
d

d
A A

B D

9778-215-02 9778-215-03

d ... slab thickness max.30 cm d ... slab thickness max.30 cm


A Universal end-shutter support 30cm A Universal end-shutter support 30cm
B Nail 3.1x80 C Doka formwork sheet 3-SO
C Doka formwork sheet 3-SO D Spax screws 4x40 (fully threaded)
E Doka beam H20
Tip for striking formwork:
➤ Take out the nails on the stop-end side.
➤ Put the claw of a hammer under the corner
(put a piece of wood under it to protect the
formwork sheeting)
➤ Lever up the end-shutter support

Tr652-203-02

34 999778002 - 04/2023
User Information Dokaflex table Tables around edges of slab

Edge table with downstand beam


with Beam forming support 20 and Extension for
beam forming support 60cm
B
A C

D E
586149000-3b

A
F

9778-217-01

A Beam forming support 20


586148000-3b
B Extension for beam forming support 60cm
A Beam forming support 20 C Height compensation with squared timbers or formwork beams
B Extension for beam forming support 60cm D Edge table
E Dokaflex table
The Beam forming support 20 is the professional way F Tie-back
of forming drop beams and slab stop-ends. In conjunc-
tion with the Extension for beam forming support 60cm,
For more information on forming downstand
exact height adjustment to within 1 cm is possible.
beams and slab stop-ends, see the 'Dokaflex'
This does away with time-consuming jobsite squared-
User Information booklet.
timber constructions. The Beam forming support auto-
matically clamps the formwork tight, resulting in clean
concrete surfaces and grout-tight edges.

9778-217-02

999778002 - 04/2023 35
Tables around edges of slab User Information Dokaflex table

36 999778002 - 04/2023
User Information Dokaflex table Repositioning

Repositioning
General instructions on repositioning

NOTICE
WARNING
When tableforms are left free-standing
➤ 'Passenger transportation' is forbidden!
(short-term intermediate storage), the fol-
➤ Before repositioning the tableform, remove lowing conditions must be met:
all loose items (e.g. fitting boards) from it.
▪ There must be a firm horizontal surface.
➤ Check the connections between the floor
props and the tableform before repositioning ▪ No attachments such as table platforms,
safety barriers, downstand beams, etc.
it.
▪ Max. height of tables 3.0 m.
WARNING ▪ Max. wind speed: 72 km/h.
If these conditions are not met, the tables must
Risk of intermediate props dropping out
be secured with a suitable tie-back (see the
when table is lifted
section headed 'Tie-back solutions')!
➤ Intermediate props with a Supporting head
H20 DF, and props that are only secured NOTICE
against tipping over, must be removed
before the table is lifted. ▪ The table must not be loaded - not even
temporarily with e.g. a stack of panels - until
➤ Intermediate props that are attached by an
it has been completely erected according to
Intermediate head DF and are not dis-
plan (i.e. with all intermediate props).
mounted must be pulled in sufficiently far.
For information on fitting intermediate props,
see the section headed 'Mounting the floor
props'.
NOTICE
Observe the following points when reposi-
tioning / travelling tableforms horizontally:
▪ There must be a flat, firm (e.g. concrete),
adequately dimensioned floor that is capa-
ble of supporting the load.
▪ Max. permitted inclination of trackway: 3%
▪ Min. height of tables: 2.00 m.
▪ Take particular care with:
- height offsets
- steps
- floor holes and wall openings
- tight spaces
- strong winds
▪ It is forbidden to use any other mechanical
assistance for the travelling operation!
▪ For longer breaks between operations, or
when the shifting device is permanently
parked, it must not be carrying any form-
work.

999778002 - 04/2023 37
Repositioning User Information Dokaflex table

Horizontal repositioning / travelling


DoKart plus Height adjustment
The DoKart plus is a battery-powered lifting appliance The Stacking frame DF is used for increasing the
that allows Doka tableforms to be travelled by just one height range.
man.
The battery is designed to allow 1 whole day's opera-
tion before being recharged on mains electricity over-
night. D C
The tableforms are lifted and lowered hydraulically.

h
A

Max. travel speed: 5 km/h (walking pace)

Max. load, where load is applied centrally:


▪ without Stacking frame DF: 1950 kg
▪ with one Stacking frame DF: 1868 kg
▪ with two Stacking frames DF: 1786 kg 9767-339-01

▪ with three Stacking frames DF: 1704 kg


A DoKart plus carrying frame
B Stacking frame DF
Follow the directions in the Operating Instruc- C Distribution beam (Doka beam H20 2.65m)
tions! D Brace stirrup 8

Intended use Height ranges incl. distribution beams


Number of Stacking h min. h max.
frames DF [cm] [cm]
The DoKart plus and the stacking frames may only be
0 174.0 344.0
used for repositioning Dokaflex, Dokamatic and
DokaXdek tables. 1 249.0 419.0
2 324.0 494.0
3 399.0 569.0

Assembly instructions for Stacking frame DF:


➤ Bolt the stacking frame to the carrying frame of the
DoKart plus with M12 threaded fasteners (4 of), or to
another stacking frame already bolted into position.

E B

A
H
F
9767-341-01

Nuts, bolts etc. are included in the scope of supply of the Stacking
frame DF.
A Carrying frame of DoKart plus, or another Stacking frame DF
B Stacking frame DF
E Hexagon bolt M12x40
F Hexagon nut M12
G Washer A13
H Spring washer A12

38 999778002 - 04/2023
User Information Dokaflex table Repositioning

Distribution beams Positioning under the tableform

NOTICE NOTICE
Before tableforms can be repositioned, 2 extra ▪ Bolt on the fastening clamps (A) of the floor
distribution beams must be installed. props from the inside to the outside, so that
they are facing outward and do not obstruct
the DoKart plus when it moves in under the
WARNING
table.
Risk of injury when the DoKart plus with pro-
jecting distribution beams is moved!
➤ Use distribution beams 1.80m long on the
DoKart plus without stacking frame!

Selecting the right distribution beams:


A A
Length of distribution beams
(Doka beams H20)
L = 1.80m
9778-249-04
L
without ▪ The outriggers of the DoKart plus extension
stacking frames set (if fitted) must also be completely
pushed in.
B A
9778-202-03
Depending on the size of the table and the situation on
Lmin = 2.65m the site, the DoKart plus is travelled under the table
L
either from one end or one side of the table.
with The carrying frame of the DoKart plus and the
stacking frames Stacking frame DF come with centre markings
(red arrows).
A
9778-242-02 C These make it easier for them to be positioned
centrally beneath the tables.
A Distribution beam (Doka beam H20)
B DoKart plus carrying frame NOTICE
C Stacking frame DF
Points to remember with unsymmetrical
Fitting the distribution beams: tables:
➤ Attach both (Doka beams H20) to the carrying frame 'Central positioning' means 'central' in terms of
of the DoKart plus, or to the Stacking frame DF, with the load centre.
two Brace stirrups 8 in each case. Take particular care with unsymmetrical tables
Arrange the distribution beams symmetrically, (edge tables, tables with stop-ends).
spaced max. 900 mm apart.
c Max. permitted eccentric position for the load centre:
a = max. 200 mm
b = max. 100 mm.
A
C
aa b b
D

9767-346-01

c ... max. 900 mm


A Distribution beam (Doka beam H20)
C Brace stirrup 8 (four of these are supplied with the DoKart plus)
D Carrying frame of DoKart plus or Stacking frame DF

9767-345-01

999778002 - 04/2023 39
Repositioning User Information Dokaflex table

Travelling the tableform Setting down and positioning the


tableform
WARNING
Risk of tipping over! NOTICE
➤ Do not extend the lifting tower of the DoKart Before setting down the table, push the fasten-
plus farther than necessary. ing clamps (A) of the floor props through from
➤ Push the floor props all the way in. the inside to the outside so that they are not an
➤ Lower the tableform to max. 10 cm above obstruction when the DoKart plus is moved out
the ground. from under the table.
➤ If necessary, extend the outriggers of the
DoKart plus extension set.
WARNING
Risk of injury when the DoKart plus with
projecting distribution beams is moved! A A
➤ Use distribution beams 1.80m long on the
DoKart plus without stacking frame!
9778-249-04
WARNING
➤ Special care is necessary in the occupation ▪ The fastening clamp (A) has to be pushed
area of the turned draw-bar of the DoKart all the way into the floor prop.
plus shown here! ▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

98017-202-01

NOTICE
▪ The outriggers of the DoKart plus extension
CAUTION set (if fitted) must be completely pushed in.
▪ Check the wedge-clamped joins between
The fastening clamp of the floor prop can work the floor props.
loose during transport and possibly drop out.
➤ Use the adjusting nut (B) to hold the fasten-
ing clamp (A) in place at the top or bottom
end of the slot (depending on whether the
outer tube (C) is at the bottom or the top).
9773-283-02
9773-283-01

C
B

A
B

C
b

9778-242-01

b ... max. 10 cm

40 999778002 - 04/2023
User Information Dokaflex table Repositioning

Vertical repositioning with transport forks


The transport fork can be used to move tableforms out Transport fork 1.3t adjustable
from under the cast floor-slab and to reposition them.

Note: ▪ Adjustable fork width


▪ Ensure correct centre-of-gravity position! ▪ Adjustable fork length
- Required minimum width of the forks: ▪ Integrated tag-lines
1/ of the width of the table
3 ▪ Three attachment possibilities for 2-part lifting chains
- Required minimum length of the forks: for optimum (horizontal) transport of the table
2/ of the length of the table
3 ▪ Attaching/detaching the 2-part lifting chain is easy in
▪ For additional measures for repositioning tables car- the parking position (bracket tilts down when lowered
ried at right angles to the forks or repositioning cus- to the ground
tom tables (downstand beams, 2 connected tables,
...) consult your Doka technician!

h
l

b ... 90, 137, 204 or 227 cm


l ... 275, 324, 373 or 422 cm
h ... 385 cm

Max. working load limit: 1300 kg (2870 lbs)

Follow the Operating Instructions!

Table along the forks Table at right angles to the


forks
(e.g. balcony table)

l
x
9778-250-02

l ... Fork length (min. 2/3 table length)


x ... Length of table

999778002 - 04/2023 41
Repositioning User Information Dokaflex table

Transport fork DM 1.5t (adjustable)


WARNING
Tableform falling-hazard!
▪ Adjustable fork width
Using the Doka beams H20 in this way deacti-
▪ Integrated tag-lines vates the lever-latch so that it no longer acts as
▪ Fork marks for optimum (horizontal) transport of the an anti-slide-off guard.
table ➤ Do not use the transport fork for regular lift-
▪ Attaching/detaching the 2-part lifting chain is easy in ing operations if Doka beams H20 are
the parking position (bracket tilts down when lowered mounted to it!
to the ground)
▪ Additional vertical extension (art. n° 586235000) for
Lifting tables over two storeys
repositioning tableforms over two storeys
The Lifting extension bracket of the transport fork is
lengthened with the Vertical extension DM 3.30m.

a
l

b
b ... 90, 137, 204 or 227 cm
l ... 580 cm
h ... 421 cm

Max. working load limit: 1500 kg (3300 lbs)


9778-250-04
Follow the Operating Instructions! a ... 7500 mm
F Vertical extension DM 3.30m

Table along the forks Table at right angles to


the forks

b
9778-250-01 x

b ... Fork width


x ... max. 3 x fork width (otherwise table has to be secured)
When lifting a table at right angles to the forks, secure
Doka beams H20 to the fork profiles at right angles to
the fork axis.

42 999778002 - 04/2023
User Information Dokaflex table Repositioning

Lifting extension bracket DF 1t / Table along the forks Table at right angles to the
forks
Transport fork DF 1t 0.90m
The transport forks are made up of a:
▪ Lifting extension bracket DF and a
▪ Transport fork DF of the appropriate width
For standard sizes of table, a 90 cm wide fork is recom-
mended.
For heavy tables with attached platforms, choose the
1.5 t system. b
x
9778-250-03
a
b ... Fork width
x ... max. 3 x fork width (otherwise table has to be secured)

A
h

C
b
b D
l
b
9767-211-01

Overview of variants
max. load-bearing
capacity 1000 kg 1500 kg
(table weight)
max. table size
5.0 x 4.0 m 8.0 x 5.0 m
(length x width)

Lifting extension Lifting extension


Item (A)
bracket DF 1t bracket DF 1.5t
Bracket length (a) 336 cm 456 cm
Clear opening (h) 280 cm 350 cm

Transport fork DF Transport fork DF


Item (B)
1t 0.90m 1.5t 0.90m
Fork width (b) 90 cm 90 cm

Transport fork DF Transport fork DF


Item (C)
1t 1.30m 1.5t 1.30m
Fork width (b) 128 cm 128 cm

Transport fork DF Transport fork DF


Item (D)
1t 2.00m 1.5t 2.00m
Fork width (b) 200 cm 200 cm

Fork length (l) 380 cm 600 cm

Follow the directions in the Operating Instruc-


tions!

999778002 - 04/2023 43
Repositioning User Information Dokaflex table

Loading platform
Where necessary, a loading platform can be assem-
bled from Doka standard components.
Using the Lifting hook DF or Dokamatic lifting straps
13.00m, the Dokaflex tables are lifted off the loading
platform and up to the next level.

9778-222-01

Note:
For assembling a loading platform, consult your Doka
technician!

44 999778002 - 04/2023
User Information Dokaflex table Repositioning

Repositioning operation
➤ Lift the table out, and up to next storey.
CAUTION
The fastening clamp of the floor prop can work
loose during transport and possibly drop out.
➤ Use the adjusting nut (B) to hold the fasten-
ing clamp (A) in place at the top or bottom
end of the slot (depending on whether the
outer tube (C) is at the bottom or the top).

9773-283-02
9773-283-01
C
B

A
B

C
9778-250-06
➤ Wheel the table to the pick-up point with the DoKart
plus. ➤ Set the table down at its new location.

9778-239-01

➤ Set the table down.


➤ Wheel out the DoKart plus from under the table (the 9778-250-07
next table can now be prepared for repositioning).
Check that the intermediate props are held
firmly in the Intermediate head DF!
➤ Manoeuvre the transport fork under the table.

9778-250-05

➤ Pick up the table with the transport fork.

999778002 - 04/2023 45
Repositioning User Information Dokaflex table

NOTICE
Before setting down the table, push the fasten-
ing clamps (A) of the floor props through from
the inside to the outside so that they are not an
obstruction when the DoKart plus is moved out
from under the table.

A A

9778-249-04

▪ The fastening clamp (A) has to be pushed


all the way into the floor prop.
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

98017-202-01

NOTICE
▪ The outriggers of the DoKart plus extension
set (if fitted) must be completely pushed in.
▪ Check the wedge-clamped joins between
the floor props.

46 999778002 - 04/2023
User Information Dokaflex table Repositioning

Lining-and-levelling the Dokaflex tables

NOTICE
▪ Before lining-and-levelling, check whether
all the floor props are under load. Only
props that are actually standing on the
ground can be lined-and-levelled.
▪ Check the wedge-clamped joins between
the floor props and the tableform.

▪ The fastening clamp (A) has to be pushed


all the way into the floor prop.
▪ Adjusting nut (B) has to be tightened into
contact with the fastening clamp.

98017-202-01

NOTICE
Follow the directions in the section headed
'Setting down and positioning the tableform'!

Plastic mallet 4kg:


▪ For fine-positioning a tableform quickly with-
out using any shifting devices.
▪ Integrated base makes it easy to put the
mallet on 'stand-by'.
▪ The mallet has been designed with just the
right weight and with plastic of the right
hardness to prevent damage.

NOTICE
▪ Use only moderate force when striking with
the plastic mallet. Max. mallet backswing
distance 50 cm!
▪ Give just one knock to each floor prop at a
time, then move on to the next prop!
▪ Strike only the bottom part of the floor prop.

999778002 - 04/2023 47
Table Lifting System TLS User Information Dokaflex table

Table Lifting System TLS

Doka Table Lifting System TLS - for NOTICE


vertical lifting of Doka tableforms All work in connection with assembly & erec-
tion, dismantling, and the first time of putting
with no need for a crane into service, must be supervised by certified
Doka specialists.
The Doka Table Lifting System TLS is used for moving ▪ The crew who are going to operate the
Doka tableforms up to the next floor. Doka Table Lifting System TLS need spe-
It is also suitable for transporting Doka equipment cial skills and knowledge which can only
between floors, in suitable multi-trip packaging contain- be passed on by certified Doka specialists.
ers (always comply with the loading data and loading ▪ As proof that they have received such spe-
rules for the Table Lifting System). cial instruction, a certificate is issued to per-
sons who have undergone this training.
NOTICE
▪ Persons who do not have this certificate are
‘Passenger transportation’ with the Table Lift- not allowed to start up or use the Doka
ing System TLS is forbidden. (Exception: for Table Lifting System TLS.
carrying out site-assembly and maintenance
work)
A comprehensive system of safety features makes for
fast, safe working, both when operating the Table Lift-
ing System itself and when cycling tables.
With the Doka Table Lifting System TLS you can even
carry on cycling tables safely during strong winds (up to
max. 72 km/h).

9778-224-01

48 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Product description
Lifting platform TLS
O
P
M Max. load:
L when lifting: 1650 kg
during loading: 2650 kg

▪ Loading area:
K F
- Entrance width: 2.70 m
(3.20 m between lifting masts)
- Length: 4.93 m
N

E
4.93
D

I
B
C
A

2.70

9767-326-01
H
▪ Integral railings
J
▪ Integral loading gates
▪ Integral loading ramp
▪ Protective grating TLS 1.80m may also be mounted
9767-318-01 if desired
A Basic unit TLS
B Lifting platform TLS centre 3.00x1.60m Landing level safety gates
C Lifting platform TLS back 3.00x1.60m
D Protective grating TLS 1.80m
E Protecting metal sheet TLS
▪ For safeguarding the loading and offloading points
F Lifting mast TLS 1.50m ▪ Landing level safety gates for every floor
G Supporting profile TLS 5.15m ▪ Integral control for every floor
H Pressure strut TLS 3.70m
I Floor support TLS 0.40m
Drive mechanism
J Adjusting device TLS
K Beam for landing level safety gate TLS 0.40m
L Landing level safety gate TLS with handle The Table Lifting System is driven electromechanically.
M Landing level safety gate TLS w. limit switch ▪ Required supply voltage: 400V/50Hz (fuse protec-
N Switch box TLS ground control tion min. 3 x 32A, slow-blow)
O Switch box TLS landing level safety gate
P Lifting cross-bar TLS
Lifting speed
Q Lifting beam TLS 67kN (in 'parked' position)

▪ Starting speed: 5 m/min.


Bottom to top-floor height ▪ Lifting speed: 10 m/min.

▪ standing on ground and working from ground level:


max. 100 m
▪ when suspended from floor-slab: max. 15 m

999778002 - 04/2023 49
Table Lifting System TLS User Information Dokaflex table

Loading data
Anchoring forces per suspension
point

FX(2) FY(2)
FZ(1)A
FZ(2)

FX(1) FY(1) FZ(1)A

FZ(1)B
FX(1) FY(1)
A
FZ(1)B

FX(0) A

9778-224-02
FX(0)
A Temporary reshore (locate as statically required)
9778-225-01

A Temporary reshore (locate as statically required)

Floor support TLS 0.40m for max. 7 lifting mast sections (max. bottom to top-floor height
10.5 m)
Vertical reac- Forces on dowel Horizontal
Inter-floor dis-
tion force Tension Shear shoring force
tance
FZ(1)B,k FZ(1)A,k FY(1),k (90° to Fx) FX(1),k FX(0),k
2.65 m 73 kN 26 kN 4 kN 32 kN 37 kN
3.00 m 73 kN 26 kN 4 kN 28 kN 33 kN
4.50 m 73 kN 26 kN 4 kN 18 kN 22 kN

Floor support TLS 0.40m for max. 10 lifting mast sections (max. bottom to top-floor height 15 m)
Vertical reac- Forces on dowel Horizontal
Inter-floor dis-
tion force Tension Shear shoring force
tance
FZ(1)B,k FZ(1)A,k FY(1),k (90° to Fx) FX(1),k FX(0),k
2.65 m 79 kN 28 kN 5 kN 34 kN 39 kN
3.00 m 79 kN 28 kN 5 kN 30 kN 35 kN
4.50 m 79 kN 28 kN 5 kN 20 kN 25 kN

Lifting mast anchoring TLS cross bar 0.40m Lifting mast anchoring TLS wall
Vertical reac- Forces on dowel Vertical reac- Forces on dowel
Inter-floor dis- Inter-floor dis-
tion force Shear tion force Shear
tance tance
FZ(2),k FY(2),k (90° to Fx) FX(2),k FZ(2),k FY(2),k (90° to Fx) FX(2),k
2.65 m 2 kN 16 kN 16 kN 2.65 m 2 kN 4 kN 20 kN
3.00 m 2 kN 16 kN 14 kN 3.00 m 2 kN 4 kN 20 kN
4.50 m 2 kN 16 kN 11 kN 4.50 m 2 kN 4 kN 20 kN
7.00 m 2 kN 8 kN 10 kN 7.00 m 2 kN 3 kN 17 kN

Subgrade reaction when stood on


ground

Bottom to top-floor
10 m 20 m 30 m 40 m 50 m 60 m 70 m 80 m 90 m 100 m
height
Total weight per mast-
3551 kg 4166 kg 4701 kg 5316 kg 5956 kg 6491 kg 7106 kg 7721 kg 8281 kg 8896 kg
side
Subgrade reaction 143 kN/m² 167 kN/m² 189 kN/m² 213 kN/m² 239 kN/m² 260 kN/m² 285 kN/m² 309 kN/m² 332 kN/m² 356 kN/m²

50 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Areas of use, possible configurations

Follow the directions in the 'Doka Table Lifting D Safety barrier at edge of slab
System TLS' Operating Instructions! E Lifting mast anchoring TLS

Space required:
Note:
h g
Check the Doka Table Lifting System TLS after assem-
bly and every time before start-up, as described in the
Operating Instructions.

Standing on ground and working


from ground level

f
System dimensions:
A

K E
9767-337-01

f ... 4.60 m
g ... 5.80 m
h ... 1.90 m
E Lifting mast anchoring TLS
e
K Landing level safety gate TLS
c

B
Note:
If the bottom to top-floor height is between 40 m and
100 m, then the Cable-reel set TLS 100.00m must be
used instead of the Cable reel TLS 40.0m (mounted to
the Basic unit TLS).
E
Note:
The Switch box TLS ground control and the Switch box
TLS landing level safety gate each come with a 10 m
d
b

control cable permanently attached.


If these switch boxes are too far (> 10 m) away from the
D
Switch box for cable-reel, then Control cables TLS
20.0m will be needed as extension cables.

E
b

D
a

9778-230-01

a ... 1.35 m (landing level safety gates mounted to the floor supports)
a ... 1.60 m (landing level safety gates mounted to the Beam for land-
ing level safety gate)
b ... max. 7.00 m (spacing between the anchorages)
c ... max. 4.50 m
(lifting height above the top lifting mast anchoring)
d ... max. 100 m
e ... min. 0.30 m
A Switch box TLS landing level safety gate
B Switch box TLS ground control
C Cable reel

999778002 - 04/2023 51
Table Lifting System TLS User Information Dokaflex table

Suspended from the floor-slab Space required:


h g

System dimensions:
H

f
K F
9767-310-01
f ... 4.60 m
g ... 5.80 m
h ... 1.90 m
c

F Floor support TLS


K Landing level safety gate TLS
E

Note:
If the total lifting height does not exceed 4.50 m
d

(1 storey), then no lifting mast anchoring is needed.


e
Loading platform
b

The Doka Table Lifting System TLS can also be used


as a loading platform.
F Usage situation:
▪ After the top floor has been completed, the Doka
tableforms are craned off the building using Doka-
matic lifting straps 13.00m or Transport forks.
a

I
f

D
J
G

9778-231-01

a ... min. 2.65 - 4.50 m


b ... max. 7.00 m (spacing between the anchorages)
c ... max. 4.50 m
(lifting height above the top lifting mast anchoring)
d ... max. 14.80 m
e ... min. 0.30 m
f ... 4.95 m
D Safety barrier at edge of slab
E Lifting mast anchoring TLS
F Floor support TLS 0.40m
G Adjusting device TLS
H Lifting cross-bar TLS
I Supporting profile TLS 5.15m
J Pressure strut TLS 3.70m

52 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Repositioning and aligning the Table Lifting System

Follow the directions in the 'Doka Table Lifting


System TLS' Operating Instructions! B

Note:
Only position the Table Lifting System in slab-edge
zones that have no projecting parts.
C
A Lifting cross-bar TLS must be mounted to each of the
Lifting masts TLS (with the lugs on the side nearest the 9767-324-01

motor) before the Table Lifting System can itself be B Lifting beam TLS 67kN
lifted and repositioned).
C Lifting platform TLS back 3.00x1.60m

Bottom to top-floor
Bottom to top-floor height 12-15 m In order to shorten the distances travelled
height of up to 10.5 m
when setting up and striking the formwork, it
A B
may be helpful to reposition the Table Lifting
System several times on one floor.

Follow the directions in the 'Lifting beam TLS


67kN' Operating Instructions!
9767-322-01
9767-355-01

A Lifting cross-bar TLS 10.50m


Aligning the Table Lifting System
B Lifting cross-bar TLS 15.00m
Depending on how far the slab-edges are out of true in
Later, the Lifting beam TLS 67kN (which is guided by the vertical, there are two possible alignment methods:
the crane hook) will be attached to these Lifting cross- ▪ Spindles in the Floor supports TLS
bars TLS. ▪ Fitting wedges between the Supporting profiles and
the floor-slab, or setting the distance with the Adjust-
ing device TLS

B
B

A
9767-320-01

A Adjusting device TLS


B Doka Express anchor 16x125mm
A

9767-323-01

A Lifting cross-bar TLS


B Lifting beam TLS 67kN

After the crane-lifting operation, the Lifting beam TLS


67kN is replaced in the holding fixture on the Lifting
platform TLS.

999778002 - 04/2023 53
Table Lifting System TLS User Information Dokaflex table

Repositioning Doka tableforms


With the DoKart plus, only one person is needed on ➤ Close the landing level safety gates.
each storey to manoeuvre the Doka tableforms. During
the automatic lifting operation, the next Doka tableform
is readied for lifting, while on the floor above, the previ-
ous tableform is moved to its proper location.
Follow the directions in the ‘DoKart plus’ Oper-
ating Instructions!

General instructions on repositioning

NOTICE
▪ Tables must be stood stably, and able to
withstand wind loads, in every phase of the
construction work.
▪ Max. wind speed during resetting:
72 km/h.
▪ No persons or unsecured objects are
9778-224-03
allowed to be on the table or the Table Lift-
ing System TLS during lifting and travelling.
➤ Raise the table to the next floor on the lifting plat-
form.
Repositioning operation
Floor above:
➤ Open the landing level safety gates.
Floor below ➤ Lower the loading ramp and open the gates of the
➤ Send the Lifting platform TLS to the floor in question. lifting platform.
➤ Open the landing level safety gates. ➤ Wheel the table off the platform.
➤ Lower the loading ramp and open the gates of the
lifting platform.

9778-228-01

9778-227-01

➤ Close the gates of the Lifting platform and tilt up the


➤ Set down the table on the lifting platform. loading ramp.
The person operating the DoKart plus must always ➤ Close the landing level safety gates.
be on the building side. ➤ Send the Lifting platform TLS back down to the floor
➤ Move out the DoKart plus from under the table. below.
➤ Secure and tie down the table if necessary (required After the last table has been repositioned, the
for edge tables with an integral downstand beam, DoKart plus can then be moved up to the next
platforms, ...). floor by the Table Lifting System.
There are crane eyes on the lifting platform for tying
back the Doka tables if necessary.
➤ Close the gates of the Lifting platform and tilt up the
loading ramp.

54 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Anchoring on the structure

NOTICE Stop anchor 15.0


11.5cm 16cm 40cm
The system is typically anchored to the struc-
a 11.5 cm 16.0 cm 40.0 cm
ture using the Tie rod system 15.0.
b 17.0 cm 22.0 cm 46.0 cm
Where the concrete cover 'd' = 2 cm
Risk of confusion! 19.0 cm 24.0 cm 48.0 cm
c
➤ When the system is combined with Doka Where the concrete cover 'd' = 3 cm
automatic climbing systems, the Tie rod 20.0 cm 25.0 cm 49.0 cm
system 20.0 must be used throughout the a ... tie-rod length
entire project. b ... installation depth
c ... minimum slab thickness
This also applies to combinations with guided d ... concrete cover
climbing systems (e.g. Guided climbing form-
work Xclimb 60). Note:
Stop anchors of different lengths should not be mixed
Positioning point and suspension in the same project.

point
WARNING
The short Stop anchor 15.0 11.5cm 90 has a
much lower load-bearing capacity than the
C Stop anchor 15.0 16cm 55.
➤ For this reason, the short stop anchor is only
A
allowed to be used on systems with low ten-
B sile loads at the anchoring location, such as
on climbing systems inside shafts.
➤ If the geometry means that it is only possible
F to install the short stop anchor, then revised
D static calculation, with extra reinforcement
9767-321-01 steel, is required in cases where larger ten-
sile loads may occur.
A Universal climbing cone 15.0
➤ The Stop anchor 15.0 11.5cm is only permit-
B Sealing sleeve K 15.0 (expendable anchoring component)
ted for slab thicknesses < 24 cm. For slab
C Cone screw B 7cm thicknesses ≥ 24 cm, the Stop anchor
D Stop anchor 15.0 (expendable anchoring component) 15.0 16cm (or larger) must be used.
F Depth mark

▪ Universal climbing cone 15.0


- The positioning point and the suspension point
are both prepared using this one single type of
cone
▪ Stop anchor 15.0 WARNING
- Expendable anchoring component for anchoring The Stop anchor 15.0 11.5cm 90 may acci-
the universal climbing cone (and thus the climb- dentally come unscrewed from the universal
ing unit) in the concrete from one side. climbing cone while low-viscosity concrete is
▪ Cone screw B 7cm being poured.
- On the positioning point – for fastening the uni- ➤ Take additional precautions to prevent the
versal climbing cone. Stop anchor 15.0 11.5cm 90 from being
- On the suspension point - for safe fastening of turned.
the floor support, of the beam for landing level The following components are fastened to the Univer-
safety gate, and of the lifting mast anchoring. sal climbing cone by means of the Cone screw B 7cm.
Stop anchor ▪ Floor support TLS 0.40m
- For safe suspension of the table lifting system in
all phases of the work.
9408-240-01
b
c
a

9767-332-02
d

999778002 - 04/2023 55
Table Lifting System TLS User Information Dokaflex table

▪ Beam for landing level safety gate 0.40m Dimensioning the suspension point
- For fixing the landing level safety gates.

The required cube compressive strength of the con-


crete at the time of loading must be specified sepa-
rately for each project by the structural designer. It
will depend on the following factors:
▪ load actually occurring
9767-329-02
▪ length of the stop anchor
▪ reinforcement / extra reinforcement steel
▪ Lifting mast anchoring TLS cross bar 0.40m
- For back-staying the Lifting masts TLS to the
▪ distance from edge
structure. The introduction of the forces, the transfer of these
forces into the structure, and the stability of the overall
construction, must all be verified by the structural
designer.
The required cube compressive strength fck,cube,current
must be at least 10 N/mm2, however.

9767-325-01
Preparing the positioning point
▪ Lifting mast anchoring TLS wall
- As an alternative to the Lifting mast anchoring The instructions given below for preparing the position-
TLS cross bar 0.40m, for back-staying the Lifting ing point apply, analogously, to all components that are
masts TLS to the structure. fastened to the Universal climbing cone using the Cone
screw B 7cm.

WARNING
➤ Always screw the stop anchor into the uni-
versal climbing cone until it fully engages (up
to the depth mark).
Not screwing the stop anchor sufficiently far
9767-354-01 into the cone may subsequently lead to
reduced load-bearing capacity and to the
failure of the suspension point – resulting in
injury and damage.
➤ Use only the Cone screw B 7cm for the posi-
tioning point and suspension point (head of
screw is red)!

WARNING
Sensitive anchoring, suspension and connec-
tor components!
➤ Never weld or heat these components.
➤ Any components that are damaged or have
been weakened by corrosion or wear must
be withdrawn from use.

NOTICE
▪ The axis of the universal climbing cone
must be at right angles to the surface of the
concrete – maximum angle of deviation: 2°.
▪ The universal climbing cone must be
embedded so that it is flush with the con-
crete surface.
▪ Do not exceed the tolerances for the loca-
tions of the positioning point and suspen-
sion point.
▪ Protect the thread from soiling.
▪ Universal climbing cones are supplied with
Sealing sleeves K. Every time the cones
are re-used, fit them with new sealing
sleeves first.

56 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Tools needed: Pouring


▪ Reversible ratchet 3/4"
▪ Universal cone spanner 15.0/20.0 (for universal ➤ Before pouring, check all positioning points and sus-
climbing cone) pension points once again.
▪ Extension 20cm 3/4"
▪ Box nut 50 3/4" (for Cone screw B 7cm) ▪ The axis of the universal climbing cone
must be at right-angles to the surface of
These tools are all included in the Tool box TLS. the concrete – maximum angle of devia-
➤ Push the sealing sleeve all the way onto the univer- tion: 2°.
sal climbing cone. ▪ The universal climbing cone must be
➤ Screw the stop anchor into the universal climbing embedded so that it is flush with the con-
cone, until it engages (up to the depth mark). crete surface.
➤ Fasten the universal climbing cone to the installation ▪ Do not exceed the tolerances for the loca-
template with a Cone screw B 7cm. tions of the positioning point and suspen-
sion point.
The installation template ensures that the
positioning point is correctly located. ▪ The sealing sleeve must be completely
pushed onto the Universal climbing cone.
▪ The depth mark on the stop anchor must
be right up against the Universal climbing
cone = must be screwed in to the full
depth.
▪ Protect the thread from soiling.
➤ Do not touch positioning points with the vibrator.
➤ Do not place concrete directly above the positioning
92841-222-02
points.
➤ Fix the installation template to the stop-end form-
work. Preparing the suspension point
92841-222-01
b
The instructions given below for preparing the suspen-
sion point apply, analogously, to all components that
are fastened to the Universal climbing cone using the
Cone screw B 7cm.
➤ Fix the Floor support TLS in the Universal climbing
cone 15.0 with a Cone screw B 7cm. A tightening
torque of 100 Nm (20 kg, assuming a ratchet-length
of approx. 50 cm) is sufficient.

NOTICE D

➤ The positioning point must align with the C


suspension point beneath it (± 10 mm in the
horizontal). A
➤ Tie the stop anchor tightly to the reinforcements with
binding wire.
A Universal climbing cone
C Cone screw B 7cm
b

D Floor support TLS

a
98009-242-01 Forcibly tightening the Cone screw B 7cm any more
a ... 3270 mm (± 20 mm) than this may cause damage and even cause the
b ... 400 mm (± 10 mm) form tie to break!
The Reversible ratchet 3/4" must be used for screwing
in and fixing the Cone screw B 7cm into the universal
climbing cone.

Reversible Reversible ratchet 3/4"


Ratchet MF 3/4" SW50
ratchet 3/4" with extension

Tr687-200-01 Tr687-200-01 Tr687-200-01

999778002 - 04/2023 57
Table Lifting System TLS User Information Dokaflex table

Possible ways of connecting the landing level safety gates

D
B

A
9767-327-03

A Landing level safety gate TLS with handle


B Landing level safety gate TLS with limit switch
C Switchbox TLS
D Floor support TLS 0.40m

Push the corner post of the landing level safety gate


down onto the mounting fixture (E) and secure with the
eyebolt (F) .

Beam for Landing level safety gate TLS


Floor support TLS 0.40m Lifting mast anchoring TLS cross-bar 0.40m
0.40m

F F
F

E
E
E

9767-336-01
9767-334-01 9767-335-01

58 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

Computation of quantities for Lifting masts TLS 1.50m


Standing on ground and working Suspended from the floor-slab
from ground level
c

d
a
b

9767-333-01

a ... Operational height


b ... 2.40 m
c ... min. 1.30 m

Operational height(a) - 2.40 m(b) + 1.30 m (c)


n ... number 1) =
1.50 m
1) Round up the result to a whole number. 9767-307-02

Total number of Lifting masts TLS 1.50m = 2 x n


d ... Lifting height Total number of Lifting masts TLS 1.50m
Up to 2.80m 4
Up to 4.30m 6
Up to 5.80m 8
Up to 7.30m 10
Up to 8.80m 12
Up to 10.30m 14
Up to 11.80m 16
Up to 13.30m 18
Up to 14.80m 20

999778002 - 04/2023 59
Table Lifting System TLS User Information Dokaflex table

Automatic climbing unit TLS


The Automatic climbing unit TLS is a lifting appliance
that is used for automatic, fast and safe raising of the
Table Lifting System TLS in construction operations,
without crane assistance.

9767-365-01

Follow the directions in the 'Automatic climbing


unit TLS' Operating Instructions!

60 999778002 - 04/2023
User Information Dokaflex table Table Lifting System TLS

999778002 - 04/2023 61
General User Information Dokaflex table

General
Combining with other Doka systems
Combining with Dokamatic tables Combining with Dokaflex or Doka
Xtra
s1
e e
A B
d

B C
9767-216-01

d ... Difference 8.2 cm


e ... 10.0 cm 9720-219-02
s1 ... 20.0 cm
A Dokamatic table B Dokaflex table
B Dokaflex table C Dokaflex or Doka Xtra

NOTICE NOTICE
The Dokamatic table and the Dokaflex table On projects with stringent quality requirements
have different overall heights. regarding the visible underside of the slab, pay
attention to the different deflections at the tran-
When selecting the props, allow for the differ- sitions between the areas formed with tables
ence d of 8.2 cm! and those formed with Dokaflex!
Follow the directions in the "Dokamatic table" Follow the directions in the 'Dokaflex' and
User Information booklet! 'Doka Xtra' User Information booklets!

62 999778002 - 04/2023
User Information Dokaflex table General

Guardrail systems on the structure


Handrail post XP 1.20m Handrail post 1.10m
▪ Attached with screw-on shoe, railing clamp, hand- ▪ Fixed in a Screw sleeve 20.0 or Attachable sleeve
rail-post shoe or Step bracket XP 24mm
▪ Protective grating XP, guardrail boards or scaffold ▪ Guard-rail boards or scaffold tubes can be used as
tubes can be used as the safety barrier the safety barrier

a
a

9771-200-01
98031-200-01

a ... > 1.00 m


a ... > 1.00 m
Follow the directions in the 'Handrail
Follow the directions in the 'Xsafe edge
post 1.10m' User Information!
protection XP' User Information booklet.

Handrail clamp S Doka floor end-shutter clamp

▪ Attached with integral clamp ▪ Slab stop-ends and fall-arrest barriers in one system
▪ Guard-rail boards or scaffold tubes can be used as
the safety barrier
a
9756-206-01

a ... > 1.00 m

Follow the directions in the “Handrail clamp S”


User information!
9767-372-01

Follow the directions in the 'Doka floor end-


shutter clamp' User Information booklet!

999778002 - 04/2023 63
General User Information Dokaflex table

Floor end-shutter profile XP


▪ Slab stop-ends and safety barriers in one system

9767-373-01

Follow the directions in the 'Xsafe edge protec-


tion XP' User Information booklet.

64 999778002 - 04/2023
User Information Dokaflex table General

Transporting, stacking and storing


Thanks to their compact design, up to 5 Dokaflex tables Lifting by crane
can be loaded onto a truck on top of one another - mak-
ing for improved logistics and reduced shipping costs.
Lifting hook DF
The Lifting hook DF can be used to hoist tableform
superstructures and ready-assembled tables.
Four Lifting hooks DF are needed for each table.

9778-234-01

Stacking and delivery condition

NOTICE
▪ Stack max. 5 elements on top of one
another!
▪ Never climb onto the stack of table ele-
ments. A

9720-226-01
▪ Before being transported by truck, the table
elements must be strapped down securely.

A Lifting hook DF

Max. load: 300 kg per Lifting hook DF


a
b

Max. weight of table: 1200 kg


d
e
c

9778-233-01

Dokaflex table Dokaflex table


Dimensions in cm
27mm 21mm
a (5 elements) 274.3 268.9
b (4 elements) 218.9 214.7
c 52.7 52.1
d (c+packing strips) 55.4 54.2
e 10.0 10.0
Precautions to prevent damage to the formwork
sheets:
9209-202-01
▪ Insert packing strips of formwork sheeting between
the table heads and the sheets. β... max. 30°

▪ Make sure the clamping wedges are pushed all the Follow the directions in the Operating Instruc-
way in, and fix them in this position with Spring cot- tions!
ters 5mm.

Intermediate storage of tables

NOTICE
Observe the following regarding intermediate
storage of completely assembled tables:
▪ Only set down tables on level, firm surfaces.
▪ Never place ready-to-use tables on top of
one another.
▪ In exposed locations, secure against wind
pressure.

999778002 - 04/2023 65
General User Information Dokaflex table

Dokamatic lifting strap 13.00m Lifting single tables

The Dokamatic lifting strap 13.00m is a lifting acces- The integrated strap shoes are not pushed onto the
sory that is only suitable for lifting Doka tableforms and secondary beams. This makes it possible to operate
stacked Doka panels. the Lifting strap 13.00m when working from ground
level.
2 Dokamatic lifting straps are needed for each unit to be
The strap shoes can either remain on the strap, or be
lifted.
detached from it as needed.

Max. working load limit:


2000 kg / Dokamatic lifting strap 13.00m

▪ Strap shoes for safe lifting of stacked tableform


superstructures.
▪ Anti-dropout safeguard for strap shoes B

▪ Moveable, 8 m long protective sleeve makes it pos-


sible to lift in a horizontal position, and protects the
strap fabric.

Follow the directions in the Operating Instruc-


tions!

Lifting of stacks
9778-237-01

To lift stacked tableform superstructures, the Doka-


B Strap shoes
matic lifting strap 13.00m is used with integrated
strap shoes.

9778-235-02

9778-235-01

66 999778002 - 04/2023
User Information Dokaflex table General

Utilise the benefits of Doka multi-trip packaging


Using Doka skeleton transport boxes
on your site. 1.70x0.80m as transport devices
Multi-trip packaging such as containers, stacking pal-
lets and skeleton transport boxes keep everything in Lifting by crane
place on the site, minimise time wasted searching for
parts, and streamline the storage and transport of sys- NOTICE
tem components, small items and accessories.
▪ Multi-trip packaging items may only be lifted
one at a time.
Doka skeleton transport box ▪ Only lift the boxes when their sidewalls are
closed!
1.70x0.80m ▪ Use a suitable crane suspension tackle
(e.g. Doka 4-part chain 3.20m).
Storage and transport device for small items Do not exceed the permitted working load
limit.
▪ Sling angle β max. 30°!

9234-203-01

Repositioning by forklift truck or pallet stacking


truck

The forks can be inserted under either the broadside or


the narrowside of the containers.
Max. load-bearing capacity: 700 kg (1540 lbs)
Permitted imposed load: 3150 kg (6950 lbs)

To make the Doka skeleton transport box easier to load


and unload, one of its sidewalls can be opened.

Using Doka skeleton transport boxes


1.70x0.80m as storage units

Max. n° of units on top of one another


Outdoors (on the site) Indoors
Floor gradients up to 3% Floor gradients up to 1%
2 5
It is not allowed to stack empty
pallets
on top of one another!

NOTICE
Stacked multi-trip boxes or pallets must have
the heaviest boxes at the bottom and the light-
est at the top.

999778002 - 04/2023 67
General User Information Dokaflex table

Doka multi-trip transport box Doka multi-trip transport box


1.20x0.80mx0.41m
Storage and transport device for small items

Doka multi-trip transport box 1.20x0.80m

Max. carrying capacity: 750 kg (1650 lbs)


Permitted imposed load: 7200 kg (15870 lbs)

Using Doka multi-trip transport boxes as


storage units
Max. carrying capacity: 1500 kg (3300 lbs)
Permitted imposed load: 7850 kg (17300 lbs) Max. n° of units on top of one another
Outdoors (on the site) Indoors
Different items in the Doka multi-trip transport box can Floor gradients up to 3% Floor gradients up to 1%
be kept separate with the Multi-trip transport box par- Doka multi-trip transport box Doka multi-trip transport box
titions 1.20m or 0.80m. 1.20x0.80m 1.20x0.80x0.41m 1.20x0.80m 1.20x0.80x0.41m
3 5 6 10
It is not allowed to stack empty
pallets on top of one another!

A NOTICE
9206-204-01

Stacked multi-trip boxes or pallets must have


the heaviest boxes at the bottom and the light-
est at the top.

Using Doka multi-trip transport boxes as


A Slide-bolt for fixing the partition transport devices
Possible ways of dividing the box
Multi-trip transport in the longitudinal in the transverse Lifting by crane
box partition direction direction
1.20m max. 3 partitions - NOTICE
0.80m - max. 3 partitions
▪ Multi-trip packaging items must be lifted
individually.
▪ Use a suitable crane lifting tackle
(e.g. Doka 4-part chain 3.20m).
Do not exceed the permitted working load
9206-204-02 9206-204-03 limit.
▪ Sling angle β max. 30°!

9206-202-01

Repositioning by forklift truck or pallet stacking


truck

The forks can be inserted under either the broadside or


the narrowside of the containers.

68 999778002 - 04/2023
User Information Dokaflex table General

Doka stacking pallet 1.55x0.85m and Using Doka stacking pallets as transport
1.20x0.80m devices

Lifting by crane
Storage and transport devices for long items.

NOTICE
▪ Multi-trip packaging items must be lifted
individually.
▪ Use a suitable crane lifting tackle
(e.g. Doka 4-part chain 3.20m).
Do not exceed the permitted working load
limit.
▪ Load the items centrically.
▪ Fasten the load to the stacking pallet (e.g.
with strapping tape or lashing strap) so that
it cannot slide or tip out.
▪ Sling angle β max. 30°!
Max. carrying capacity: 1100 kg (2420 lbs)
Permitted imposed load: 5900 kg (12980 lbs)

Using Doka stacking pallets as storage units

Max. n° of units on top of one another


Outdoors (on the site) Indoors
Floor gradients up to 3% Floor gradients up to 1%
= =
2 6
a
It is not allowed to stack empty
92815-224-01
pallets on top of one another!

NOTICE a
▪ Stacked multi-trip boxes or pallets must Doka stacking pallet 1.55x0.85m max. 4.5 m
have the heaviest boxes at the bottom and Doka stacking pallet 1.20x0.80m max. 3.0 m
the lightest at the top.
▪ How to use with Bolt-on castor set B: Repositioning by forklift truck or pallet stacking
- Always apply the fixing brake when the truck
container is 'parked'.
- When Doka stacking pallets are NOTICE
stacked, the bottom pallet must NOT be ▪ Load the items centrically.
one with a bolt-on castor set mounted to
it. ▪ Fasten the load to the stacking pallet (e.g.
with strapping tape or lashing strap) so that
it cannot slide or tip out.

999778002 - 04/2023 69
General User Information Dokaflex table

Doka accessory box Doka accessory box as transport devices

Storage and transport device for small items Lifting by crane

NOTICE
▪ Multi-trip packaging items must be lifted
individually.
▪ Use a suitable crane lifting tackle
(e.g. Doka 4-part chain 3.20m).
Do not exceed the permitted working load
limit.
▪ When lifting accessory boxes to which Bolt-
on castor sets B have been attached, you
must also follow the 'Bolt-on castor set B'
User Information booklet!
Max. carrying capacity: 1000 kg (2200 lbs)
▪ Sling angle β max. 30°!
Permitted imposed load: 5530 kg (12191 lbs)

Doka accessory boxes as storage units

Max. n° of units on top of one another


Outdoors (on the site) Indoors
Floor gradients up to 3% Floor gradients up to 1% 92816-206-01
3 6
It is not allowed to stack empty
pallets on top of one another! Repositioning by forklift truck or pallet stacking
truck
NOTICE
▪ Stacked multi-trip boxes or pallets must The forks can be inserted under either the broadside or
have the heaviest boxes at the bottom and the narrowside of the containers.
the lightest at the top.
▪ How to use with Bolt-on castor set B: Bolt-on castor set B
- Always apply the fixing brake when the
container is 'parked'.
- When Doka stacking pallets are The Bolt-on castor set B turns multi-trip packaging
stacked, the bottom pallet must NOT be items into fast and manoeuvrable transport devices.
one with a bolt-on caster set mounted to Suitable for drive-through access openings > 90 cm.
it.

The Bolt-on castor set B can be mounted to the follow-


ing multi-trip packaging items:
▪ Doka accessory box
▪ Doka stacking pallets
▪ Protective barrier Z pallets
Follow the directions in the 'Bolt-on castor
set B' User Information booklet!

70 999778002 - 04/2023
User Information Dokaflex table General

Reshoring props, concrete technology and stripping out

Follow the directions in the Calculation Guide Why put up reshoring props after
entitled 'Stripping out formwork from floors in
building construction', and/or ask your Doka
stripping out the formwork?
technician.
After the formwork has been stripped and the slab has
been stress-relieved or dismantled, the slab is able to
When is the best time to strip out the bear its dead load and live loads resulting from the con-
struction state, but not the concreting loads from subse-
formwork? quent floor-slabs.
The temporary reshoring serves to support the floor-
The concrete strength needed before the formwork can slab and distribute the concreting loads across several
be stripped out will depend upon the load factor α. This floors.
can be read off from the following table.

Load factor α Positioning the reshoring props


correctly
This is calculated by:
Reshoring props have the job of spreading loads
DLconcrete + LLconstruction state between the new floor-slab and the floor beneath it.
α= DLconcrete + DLfinishing + LLfinal This load distribution will depend on the relationship
state between the rigidities of these two floor-slabs.
Load factor α NOTICE
Slab Dead load LLfinal state
thickness DLconcrete Ask an expert!
d [m] [kN/m2] 2.00 3.00 4.00 5.00
kN/m2 kN/m2 kN/m2 kN/m2 As a rule, the question of using reshoring
0.14 3.50 0.67 0.59 0.53 0.48 props should be referred to the responsible
0.16 4.00 0.69 0.61 0.55 0.50 experts, regardless of the information given
0.18 4.50 0.71 0.63 0.57 0.52 above.
0.20 5.00 0.72 0.65 0.59 0.54 Observe all local standards and regulations!
0.22 5.50 0.74 0.67 0.61 0.56
0.25 6.25 0.76 0.69 0.63 0.58
0.30 7.50 0.78 0.72 0.67 0.62 Strength development in the new
0.35 8.75 0.80 0.75 0.69 0.65
concrete
Valid for a finishing-load DLfinishing = 2.00 kN/m2 and a live load in the
early-stripped state of LLconstruction state = 1.50 kN/m2
DLconcrete: calculated with γconcrete = 25 kN/m3 Rough reference values can be found in DIN 1045-
DLfinishing: load for floor finish, etc. 3:2008, Table 2. The length of time until 50 percent of
the final (28-day) strength is reached can be read off
from this Table as a function of the temperature and the
Example: Slab thickness 0.20 m with a final live load of
type of concrete.
5.00 kN/m2 results in a load factor α of 0.54.
The values are only valid if the concrete is given cor-
This means that formwork removal / stress-release can
rect, appropriate curing throughout the entire period.
take place once the concrete has reached 54% of its
28-day strength. The load-bearing capacity will then For a concrete with medium strength development, the
correspond to that of the finished structure. following inferred diagram may thus be used.

Concrete-strength development – medium


NOTICE 100
If the floor props are not stress-relieved, mean-
Compressive strength of concrete [%]

90
ing that the slab has not been activated, then 80
the props will remain loaded with the dead
70
weight of the floor-slab. A B C
When the floor above is concreted, this 60
may lead to a doubling of the load that is 50
being applied to the floor props. 40
The floor props are not designed to cope with 30
such an overload, and the result may be dam-
20
age to the formwork, the floor props and the
98059-100

structure. 10
0
0 4 8 12 16 20 24 28
Hardening (curing) duration [days]

999778002 - 04/2023 71
General User Information Dokaflex table

A ϑ ≥ 15° Removing the load from the formwork


B ϑ ≥ 10°
C ϑ ≥ 5°
from wide-spanned floor-slabs with
support centres of over 7.5m
Deflection of the new concrete
In the case of thin, wide-spanned concrete floor-slabs
(e.g. in multistorey car parks), the following points must
The concrete's modulus of elasticity develops faster be remembered:
than compressive strength. At 60 % of its compressive
strength fck, the concrete has already reached approxi- ▪ When the formwork beneath these floor-slab spans
mately 90% of its modulus of elasticity Ec(28). is released (i.e. when the load is taken off the floor
props), the floor props that are still in place are briefly
The increase in the elastic deformation taking place in
subjected to additional loads. This may lead to over-
the new concrete is thus only negligible.
loading, and to the floor props being damaged.
The creep deformation, which only finally ceases after ▪ Please consult your Doka technician.
several years, is several times more than the elastic
deformation. NOTICE
Early striking – e.g. after 3 days instead of 28 – thus As a basic rule:
only leads to an increase in the total deformation of less
than 5%. ▪ Stress-release should always be carried out
working from one side towards the other,
The part of this deformation accounted for by creep or from the middle of the floor slab (mid-
deformation, however, may be anything between 50% span) towards the slab-edges.
and 100% of the standard value, due to such variable
influences as the strength of the aggregates, and the For wide spans, this procedure MUST be
atmospheric humidity. This means that the total deflec- followed!
tion of the floor-slab is practically independent of the ▪ Stress-release must NEVER be carried out
time at which the formwork was struck. from both sides towards the middle!

l
Cracks in new concrete A A

The bonding strength between the reinforcement steel


and the concrete develops more rapidly in the new con-
crete than does its compressive strength. This means
that early stripping does not have any negative influ-
ence upon the size and distribution of cracks on the ten-
sion side of reinforced concrete constructions. 98059-105
Other cracking phenomena can be countered effec-
tively by appropriate curing methods.
l

Curing of new concrete A A

New site-placed concrete is exposed to influences


which may cause cracking and slow down its strength
development:
▪ premature drying
▪ over-rapid cooling in the first few days 98059-105
▪ excessively low temperatures or frost
l ... Effective floor-slab spans of 7.50 m and over
▪ mechanical damage to the surface of the concrete
A Load redistribution
▪ hydration heat
▪ etc.
The simplest precaution is to leave the formwork on the
concrete surface for longer. As well as the familiar extra
curing measures, this measure should be carried out in
any case.

72 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°


ArticleN°
Article
[kg] list

Dokaflex table 2.50x4.00m 21mm 385.0 586052000 Doka floor prop Eurex 20 250 12.9 586086000
Dokaflex table 2.50x5.00m 21mm 470.0 586053000 Length: 152 - 250 cm
Dokaflex table 2.00x4.00m 21mm 317.0 586050000 Doka floor prop Eurex 20 300 15.3 586087000
Dokaflex table 2.00x5.00m 21mm 386.0 586051000 Length: 172 - 300 cm
Dokaflex-Tisch Doka floor prop Eurex 20 350 17.8 586088000
Length: 197 - 350 cm
Doka floor prop Eurex 20 400 22.2 586089000
Length: 227 - 400 cm
Doka floor prop Eurex 20 550 34.6 586090000
Length: 297 - 550 cm
Doka-Deckenstütze Eurex 20
Galvanised

Dokaflex table 2.50x4.00m 27mm 405.0 586054000


Dokaflex table 2.50x5.00m 27mm 485.0 586055000
Dokaflex table 2.00x4.00m 27mm 337.0 586056000
Dokaflex table 2.00x5.00m 27mm 411.0 586057000
Dokaflex-Tisch

Doka floor prop Eurex 20 LW 300 11.5 586876000


Length: 173 - 300 cm
Doka floor prop Eurex 20 top 150 8.0 586096000 Doka floor prop Eurex 20 LW 350 13.9 586877000
Length: 92 - 150 cm Length: 198 - 350 cm
Doka floor prop Eurex 20 top 250 12.7 586086400 Doka-Deckenstütze Eurex 20 LW
Length: 148 - 250 cm Galvanised
Doka floor prop Eurex 20 top 300 14.3 586087400
Length: 173 - 300 cm
Doka floor prop Eurex 20 top 350 17.4 586088400
Length: 198 - 350 cm
Doka floor prop Eurex 20 top 400 21.6 586089400
Length: 223 - 400 cm
Doka floor prop Eurex 20 top 550 32.3 586090400
Length: 298 - 550 cm
Doka-Deckenstütze Eurex 20 top
Galvanised

Doka floor prop Eurex 30 top 250 12.8 586092400


Length: 148 - 250 cm
Doka floor prop Eurex 30 top 300 16.4 586093400
Length: 173 - 300 cm
Doka floor prop Eurex 30 top 350 20.7 586094400
Length: 198 - 350 cm
Doka floor prop Eurex 30 top 400 24.6 586095400
Length: 223 - 400 cm
Doka floor prop Eurex 20 eco 250 11.5 586270000 Doka floor prop Eurex 30 top 450 29.1 586119400
Length: 148 - 250 cm Length: 248 - 450 cm
Doka floor prop Eurex 20 eco 300 14.0 586271000 Doka floor prop Eurex 30 top 550 38.6 586129000
Length: 173 - 300 cm Length: 303 - 550 cm
Doka floor prop Eurex 20 eco 350 16.9 586272000 Doka-Deckenstütze Eurex 30 top
Length: 198 - 350 cm Galvanised
Doka floor prop Eurex 20 eco 400 20.5 586273000
Length: 223 - 400 cm
Doka floor prop Eurex 20 eco 450 24.1 586275000
Length: 248 - 450 cm
Doka floor prop Eurex 20 eco 550 32.0 586276000
Length: 298 - 550 cm
Doka-Deckenstütze Eurex 20 eco
Galvanised

999778002 - 04/2023 73
Article list User Information Dokaflex table

[kg] Article N° [kg] Article N°

Doka floor prop Eurex 30 250 14.8 586092000 Beam screw S 8/60 0.06 580116000
Length: 152 - 250 cm Riegelverschraubung S 8/60
Doka floor prop Eurex 30 300 16.7 586093000 Galvanised
Length: 172 - 300 cm Length: 7 cm
Doka floor prop Eurex 30 350 20.5 586094000 Width-across: 13 mm
Length: 197 - 350 cm
Doka floor prop Eurex 30 400 24.9 586095000
Length: 227 - 400 cm Beam connecting plate H20 0.07 586263000
Doka floor prop Eurex 30 450 29.2 586119000 Gurtverbinder H20
Length: 248 - 450 cm Galvanised
Doka-Deckenstütze Eurex 30 Height: 8 cm
Galvanised

Universal end-shutter support 30cm 1.0 586232000


Universal-Abschalwinkel 30cm
Galvanised
Height: 21 cm

Doka floor end-shutter clamp 12.5 586239000


Doka-Deckenabschalklemme
Galvanised
Insertion beam 1.95m 7.1 183074000 Height: 137 cm
Insertion beam 2.45m 8.9 183075000
Einschubträger
Varnished yellow

Table head 20 16.5 586085000


Tischkopf 20 End-shutter shoe 1.6 586257000
Galvanised Abschalschuh
Powder-coated blue Galvanised
Length: 41 cm Height: 13.5 cm
Width: 33 cm
Height: 30 cm

Table head 30 18.5 586078000


Tischkopf 30
Galvanised End-shutter tie rod 15.0 15-40cm 0.91 586258000
Abschalanker 15,0 15-40cm
Powder-coated blue
Galvanised
Length: 44 cm
Length: 55 cm
Width: 25 cm
Height: 30 cm

Spring cotter 5mm 0.03 580204000


Federvorstecker 5mm
Galvanised Floor end-shutter profile XP 4.2 586481000
Length: 13 cm Deckenabschalprofil XP
Galvanised
Height: 77 cm

Intermediate head DF 3.6 586058000


Zwischenkopf DF
Galvanised
Length: 25 cm
Width: 24 cm
Height: 34 cm

Connection unit DF 20/30 0.93 586084000 Wheel-around scaffold DF 44.0 586157000


Spanneinheit DF 20/30 Mobilgerüst DF
Galvanised Aluminium
Width: 15 cm Length: 185 cm
Height: 12 cm Width: 80 cm
Width-across: 19 mm Height: 255 cm
Delivery condition: separate parts

Supporting head H20 DF 0.77 586179000


Haltekopf H20 DF
Galvanised
Length: 19 cm
Width: 11 cm
Height: 8 cm

74 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°

Wheel-around scaffold DF accessory set 13.3 586164000 Insertion adapter XP 4.1 586478000
Zubehörset Mobilgerüst DF Einschubadapter XP
Aluminium Galvanised
Timber parts varnished yellow Height: 43 cm
Length: 189 cm

Railing clamp XP 40cm 7.7 586456000


Geländerzwinge XP 40cm
Galvanised
Platform stairway 0.97m 23.5 586555000 Height: 73 cm
Podesttreppe 0,97m
Aluminium
Width: 121 cm
Pay attention to the national, techni-
cal safety regulations!

H20 screw-on bracket for formwork sheets 0.19 586256000


Schalhaut-Schraubwinkel H20
Galvanised Handrail-post shoe XP 2.2 586457000
Geländerschuh XP
Height: 19.2 cm
Galvanised
Length: 20 cm

Handrail post XP 1.20m 4.1 586460000


Geländersteher XP 1,20m
Lashing strap 5.00m 2.8 586018000 Galvanised
Zurrgurt 5,00m Height: 118 cm
Yellow

Doka express anchor 16x125mm 0.31 588631000


Doka-Expressanker 16x125mm
Galvanised
Length: 18 cm

Handrail post XP 1.80m 6.0 586482000


Geländersteher XP 1,80m
Doka coil 16mm 0.009 588633000 Galvanised
Doka-Coil 16mm Height: 176 cm
Galvanised
Diameter: 1.6 cm

Framax universal corner waling 12.8 588151000


Framax-Eckklemmschiene
Painted blue
Leg length: 60 cm

Retaining plate 15.0 1.8 586073000


Jochplatte 15,0
Galvanised
Length: 17 cm
Width: 12 cm
Height: 11 cm

Universal plug R20/25 0.003 588180000


Kombi-Ankerstopfen R20/25 Toeboard holder XP 0.60m 0.77 586463000
Blue Fußwehrhalter XP 0,60m
Diameter: 3 cm Galvanised
Height: 21 cm

Toeboard holder XP 1.20m 0.64 586461000


Fußwehrhalter XP 1,20m
Galvanised
Height: 21 cm

999778002 - 04/2023 75
Article list User Information Dokaflex table

[kg] Article N° [kg] Article N°

Protective grating XP 2.70x0.60m 10.1 586466000 Handrail post 1.10m 5.5 584384000
Protective grating XP 2.50x0.60m 9.5 586472000 Schutzgeländer 1,10m
Protective grating XP 2.00x0.60m 8.0 586473000 Galvanised
Protective grating XP 1.20x0.60m 5.0 586491000 Height: 134 cm
Schutzgitter XP
Galvanised

Attachable sleeve 24mm 0.03 584385000


Steckhülse 24mm
Protective grating XP 2.70x1.20m 22.2 586450000 PVC
Protective grating XP 2.50x1.20m 20.5 586451000
PE
Protective grating XP 2.00x1.20m 17.4 586452000
Protective grating XP 1.20x1.20m 12.0 586453000 Grey
Schutzgitter XP Length: 16.5 cm
Galvanised Diameter: 2.7 cm

Screw sleeve 20.0 0.03 584386000


Schraubhülse 20,0
PP
Yellow
Length: 20 cm
Diameter: 3.1 cm

Scaffold tube 48.3mm 0.50m 1.7 682026000


Scaffold tube 48.3mm 1.00m 3.6 682014000
Scaffold tube 48.3mm 1.50m 5.4 682015000
Velcro fastener 30x380mm 0.02 586470000 Scaffold tube 48.3mm 2.00m 7.2 682016000
Klettverschluss 30x380mm Scaffold tube 48.3mm 2.50m 9.0 682017000
Yellow Scaffold tube 48.3mm 3.00m 10.8 682018000
Scaffold tube 48.3mm 3.50m 12.6 682019000
Scaffold tube 48.3mm 4.00m 14.4 682021000
Scaffold tube 48.3mm 4.50m 16.2 682022000
Scaffold tube 48.3mm 5.00m 18.0 682023000
Scaffold tube 48.3mm 5.50m 19.8 682024000
Handrail post T 1.80m 17.7 584373000 Scaffold tube 48.3mm 6.00m 21.6 682025000
Einschubgeländer T 1,80m
Scaffold tube 48.3mm .....m 3.6 682001000
Galvanised Gerüstrohr 48,3mm
Galvanised

Screw-on coupler 48mm 50 0.84 682002000


Anschraubkupplung 48mm 50
Galvanised
Width-across: 22 mm

Toeboard holder T 1.80m 0.53 584392000


Fußwehrhalter T 1,80m T ledge 21/42 2.00m 0.34 580196000
Galvanised T-Leiste 21/42 2,00m
Height: 13.5 cm Grey

Handrail clamp S 11.5 580470000


Schutzgeländerzwinge S
Galvanised
Height: 123 - 171 cm
Centre bit DF 30 0.10 586081000
Zentrumsbohrer DF 30

76 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°

Strip tensioner B 6.00m 3.3 580394500 FreeFalcon


Bandzwinge B 6,00m
Galvanised
FreeFalcon 450.0 583034000
FreeFalcon
Red
Length: 225 cm
Width: 208 cm
Height: 235 cm
Follow the directions in the "Opera-
ting Instructions"!

Strip tensioner B 5.00m 3.5 580394000


Bandzwinge B 5,00m
Galvanised

Mast cover FreeFalcon 3.8 583027000


Abdeckung Mast FreeFalcon
Red

Plastic mallet 4kg 4.5 586097000


Kunststoffhammer 4kg
Blue
Length: 110 cm

Base-plate cover FreeFalcon 3.2 583026000


Abdeckung Sockelplatte FreeFalcon
Red

Universal dismantling tool 3.7 582768000 Safety harness FreeFalcon 1.5 583036000
Universal-Lösewerkzeug Auffanggurt FreeFalcon
Galvanised Follow the directions in the "Opera-
ting Instructions"!
Length: 75.5 cm

Box nut 19 1/2" L 0.16 580598000


Stecknuss 19 1/2" L

Fall arrester FreeFalcon 9.00m 3.8 583035000


Höhensicherungsgerät FreeFalcon 9,00m
Box nut 13 1/2" 0.06 580576000 Follow the directions in the "Opera-
ting Instructions"!
Stecknuss 13 1/2"

Reversible ratchet 1/2" 0.73 580580000


Umschaltknarre 1/2"
Galvanised
Fall arrester FreeFalcon 6.00m 3.3 583039000
Höhensicherungsgerät FreeFalcon 6,00m
Follow the directions in the "Opera-
ting Instructions"!

999778002 - 04/2023 77
Article list User Information Dokaflex table

[kg] Article N° [kg] Article N°

Case for safety accessories FreeFalcon 1.5 583037000 Shifting trolley DF 566.0 586080000
Koffer Sicherheitszubehör FreeFalcon Umsetzwagen DF
included in scope of supply:
(A) Positioning lever for shifting trolley DF 6.0 586063000
(B) Brace stirrup 8 2.7 582751000
4 pcs.
Galvanised
Width: 19 cm
Height: 46 cm
Width-across: 30 mm
Galvanised
Length: 181 cm
Shifting appliances for tables Width: 130 cm
Height: 154 - 303 cm
DoKart plus 1448.0 586265500 Follow the directions in the "Opera-
DoKart plus ting Instructions"!
included in scope of supply:
(A) Brace stirrup 8 2.7 582751000
4 pcs.
Galvanised
Width: 19 cm
Height: 46 cm
Width-across: 30 mm
Yellow
Length: 172 cm
Width: 132 cm
Height: 154 - 327 cm Extension for shifting trolley DF 40.0 586015000
Follow the directions in the "Opera- Ausleger für Umsetzwagen DF
ting Instructions"! Galvanised
Length: 128.4 cm
Follow the directions in the "Opera-
ting Instructions"!

Attachable drive unit DF 512.0 586062000


Andockantrieb DF
Extension set for DoKart plus 50.0 586266500 Painted blue
Auslegersatz DoKart plus
Length: 100 cm
Galvanised
Width: 100 cm
Length: 120 cm
Height: 130 cm
Follow the directions in the "Opera-
ting Instructions"! Follow the directions in the "Opera-
ting Instructions"!

DoKart 1580.0 586265000


DoKart
included in scope of supply:
(A) Brace stirrup 8 2.7 582751000
4 pcs.
Galvanised
Width: 19 cm
Height: 46 cm Stacking frame DF 82.0 586079000
Aufsatzrahmen DF
Width-across: 30 mm
Galvanised
Yellow
Length: 134 cm
Length: 173 cm
Width: 130 cm
Width: 133 cm
Height: 75 cm
Height: 154 - 324 cm
Follow the directions in the "Opera-
ting Instructions"!

Extension set for DoKart 34.0 586266000 Alu stacking frame DM 2.25m 59.2 586238000
Auslegersatz DoKart Alu-Aufsatzrahmen DM 2,25m
Galvanised Aluminium
Length: 80 cm Length: 187 cm
Follow the directions in the "Opera- Width: 128 cm
ting Instructions"!
Height: 225 cm

78 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°

Transport fork 1.3t adjustable 718.0 586234000 Extension profile H20 for fork 34.1 586237000
Umsetzgabel 1,3t verstellbar Aufsatzprofil H20 für Gabel
Galvanised Galvanised
Delivery condition: folded closed Length: 83 cm
Follow the directions in the "Opera- Height: 52 cm
ting Instructions"!

Lifting extension bracket DF 1t 263.0 586068000


Ausleger DF 1t
Galvanised
Delivery condition: folded closed
Follow the directions in the "Opera-
ting Instructions"!
Transport-fork table-fixing part 1.3t adj. 5.0 586260000
Tischfixierung Umsetzgabel 1,3t verstellbar
Galvanised
Width: 21 cm
Height: 21 cm Lifting extension bracket DF 1.5t 475.0 586064000
Ausleger DF 1,5t
Galvanised
Length: 456 cm
Transport fork DM 1.5t adjustable 1134.0 586233000
Umsetzgabel DM 1,5t verstellbar Width: 82 cm
Galvanised Height: 386 cm
Delivery condition: folded closed Delivery condition: folded closed
Follow the directions in the "Opera- Follow the directions in the "Opera-
ting Instructions"! ting Instructions"!

Transport fork DF 1t 0.90m 220.0 586069000


Transport fork DF 1t 1.30m 245.0 586070000
Transport fork DF 1t 2.00m 274.0 586071000
Gabel DF 1t
Galvanised
Length: 411 cm
Height: 58 cm
Follow the directions in the "Opera-
ting Instructions"!
Transport fork DM 2.5t adjustable 1134.0 586259000
Umsetzgabel DM 2,5t verstellbar
Galvanised
Delivery condition: folded closed
Follow the directions in the "Opera-
ting Instructions"! Transport fork DF 1.5t 0.90m 480.0 586065000
Transport fork DF 1.5t 1.30m 520.0 586066000
Transport fork DF 1.5t 2.00m 540.0 586067000
Gabel DF 1,5t
Galvanised
Length: 638 cm
Height: 71 cm
Follow the directions in the "Opera-
ting Instructions"!

Dokamatic lifting strap 13.00m 10.5 586231000


Vertical extension DM 3.30m 240.0 586235000 Dokamatic-Umsetzgurt 13,00m
Vertikalverlängerung DM 3,30m Green
Galvanised Follow the directions in the "Opera-
Height: 352 cm ting Instructions"!

Lifting hook DF 5.9 586077000


Extension clamp H20 for fork 4.5 586236000 Umsetzbügel DF
Aufsatzklemme H20 für Gabel Galvanised
Galvanised Length: 42 cm
Height: 45 cm Width: 20 cm
Height: 36 cm
Follow the directions in the "Opera-
ting Instructions"!

999778002 - 04/2023 79
Article list User Information Dokaflex table

[kg] Article N° [kg] Article N°

Table Lifting System TLS Supporting profile TLS 5.15m 210.0 586317000
Abstützprofil TLS 5,15m
Galvanised
Basic unit TLS 2336.0 586301000
Basiseinheit TLS
Length: 431 cm
Width: 242 cm
Height: 274 cm
Follow the directions in the "Opera-
ting Instructions"!

Pressure strut TLS 3.70m 70.0 586318000


Druckstrebe TLS 3,70m
Lifting platform TLS centre 3.00x1.60m 310.0 586307000
Hubbühne TLS mitte 3,00x1,60m Galvanised
Height: 139 cm

Lifting platform TLS back 3.00x1.60m 376.0 586308000


Hubbühne TLS hinten 3,00x1,60m
Height: 139 cm

Floor support TLS 0.40m 39.0 586315000


Deckenauflager TLS 0,40m
Galvanised
Length: 72.5 cm
Width: 32.1 cm
Height: 22.3 cm

Protective grating TLS 1.80m 22.0 586334000


Schutzgitter TLS 1,80m
Galvanised
Adjusting device TLS 10.0 586336000
Justiereinheit TLS
Length: 141 cm
Galvanised
Height: 121 cm
Length: 42 cm
Width: 16 cm
Height: 16 cm

Cable routing TLS 2.0 586333000


Kabelführung TLS
Galvanised
Length: 35 cm

Lifting mast anchoring TLS cross bar 0.40m 92.0 586329000


Hubmastverankerung TLS Traverse 0,40m
Galvanised
Protecting metal sheet TLS right 12.0 586309000
Protecting metal sheet TLS left 12.0 586310000 Length: 450 cm
Schutzblech TLS
Painted yellow
Length: 85 cm
Width: 32 cm
Height: 73 cm
Lifting mast anchoring TLS wall 15.5 586372000
Hubmastverankerung TLS Wand
Lifting mast TLS 1.50m 82.0 586328000 Galvanised
Hubmast TLS 1,50m Length: 52 cm
Galvanised

Lifting mast anchoring TLS strut 22.0 586331000


Hubmastverankerung TLS Strebe
Galvanised
Length: 153.5 cm
Width: 50 cm

80 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°

Lifting mast anchoring TLS mast connection 15.0 586332000 Switch box TLS landing level safety gate 7.0 586324000
Hubmastverankerung TLS Mastanschluss Schaltkasten TLS Etagentüre
Galvanised Height: 55 cm
Length: 72.6 cm
Width: 66 cm

Base profile TLS 2.14m 28.0 586312000


Bodenprofil TLS 2,14m Control cable TLS 20.0m blue 4.0 586303000
Galvanised Control cable TLS 20.0m red 4.0 586304000
Steuerkabel TLS

Bar for limit switch TLS 5.0 586325000


Endschalterschiene TLS
Galvanised
Length: 186 cm
Strut for base profile TLS 11.8 586313000
Strebe für Bodenprofil TLS
Galvanised
Length: 257.3 cm

Lifting cross-bar TLS 10.50m 18.5 586327000


Hebetraverse TLS 10,50m
Galvanised
Length: 76.5 cm

Beam for landing level safety gate TLS 0.40m 35.0 586319000
Träger für Etagentüre TLS 0,40m
Galvanised
Length: 344 cm

Lifting cross-bar TLS 15.00m 64.0 586373000


Hebetraverse TLS 15,00m
Landing level safety gate TLS with handle 33.0 586321000 Galvanised
Etagentüre TLS mit Griff Length: 189 cm
Length: 153 cm
Height: 126 cm

Lifting beam TLS 67kN 68.0 586326500


Hebeträger TLS 67kN
Landing level safety gate TLS w. limit switch 32.0 586322000 Galvanised
Etagentüre TLS mit Endschalter Length: 338 cm
Length: 153 cm Follow the directions in the "Opera-
Height: 126 cm ting Instructions"!

Switch box TLS ground control 7.0 586323000 Cable-reel set TLS 100.00m 133.0 586371000
Schaltkasten TLS Bodensteuerung
Kabeltopfset TLS 100,00m
Height: 55 cm
Galvanised
Height: 142 cm

999778002 - 04/2023 81
Article list User Information Dokaflex table

[kg] Article N° [kg] Article N°

Doka 4-part chain 3.20m 15.0 588620000 Tool box TLS 19.6 586337000
Doka-Vierstrangkette 3,20m Werkzeugbox TLS
Follow the directions in the "Opera- consisting of:
ting Instructions"! (A) Combination wrench 8 0.03 586343000
(B) Combination wrench 10 0.04 586342000
(C) Combination wrench 13 0.06 586341000
(D) Combination wrench 16 0.18 580645000
(E) Combination wrench 17 0.16 586340000
(F) Combination wrench 18 0.17 580646000
(G) Combination wrench 19 0.14 582837000
(H) Combination wrench 22 0.20 582838000
(I) Combination wrench 24 0.25 582839000
(J) Combination wrench 30 0.43 582840000
Cone screw M30 SW50 7cm 0.88 581444500 (K) Reversible ratchet 3/4" 1.5 580894000
Konusschraube M30 SW50 7cm Galvanised
Green (L) Universal cone spanner 15.0/20.0 0.90 581448000
Length: 10 cm Galvanised
Diameter: 7 cm Width-across: 50 mm
Width-across: 50 mm (M) Safety Ruler SK 0.02 581439000
Length: 18 cm
Cone screw B 7cm 0.86 581444000 (N) Extension 20cm 3/4" 0.68 580683000
Konusschraube B 7cm
(O) Slot-screw screwdriver 0.6x3.5 0.20 586344000
Red
(P) Slot-screw screwdriver 1x5.5 0.20 586366000
Length: 10 cm
(Q) Set of ball-head hexagon-socket screw keys 0.60 586346000
Diameter: 7 cm
(R) Box spanners 1/2" set of 29 5.6 586345000
Width-across: 50 mm
(S) Box nut 18 3/4" 0.22 580643000
(T) Box nut 19 3/4" 0.20 586375000
Universal climbing cone 15.0 1.3 581977000
Universal-Kletterkonus 15,0 (U) Box nut 24 3/4" 0.21 500679030
Galvanised (V) Box nut 24 1/2" L 0.30 586364000
Orange (W) Box nut 27 3/4" 0.27 586376000
Length: 12.8 cm (X) Box nut 30 3/4" 0.33 586377000
Diameter: 5.3 cm (Y) Box nut 50 3/4" 0.81 581449000

A
B
Sealing sleeve K 15.0 0.03 581976000 D
C K

Dichtungshülse K 15,0 F
E

Orange G M L
H
Length: 12 cm I
O N
Diameter: 6 cm J

R Q P

W
V
U
T
Stop anchor 15.0 B11 0.55 581868000 S
Y
Stop anchor 15.0 A16 0.38 581997000 X

Stop anchor 15.0 A40 0.71 581999000


Sperranker 15,0
Non-treated
Maintenance toolbox TLS 6.1 586369000
Wartungs-Werkzeugbox TLS
consisting of:
(A) Grease cartridge TLS 0.46 586368000
(B) Filling press TLS 0.93 586367000
(C) Thickness gauge set 0.05-1.00mm 0.09 586350000
(D) Pliers for external circlips 40-100mm 0.32 586348000
Torque wrench 3/4" 75-400Nm 2.3 586374000 (E) Water pump nut pliers 250mm 0.32 586347000
Drehmomentschlüssel 3/4" 75-400Nm (F) Screw dr. f. recessed-head scr. PZ 2 0.15 586351000
Galvanised (G) Combination wrench 14 0.09 586349000
Length: 69 cm (H) Digital multimeter TLS 0.22 586353000
(I) Dummy plug TLS 4 poles 0.04 586352000

Brake-disc pull-off tool TLS D200 4.3 586370000


Scheibenabzieher TLS D200
Height: 27 cm
Width-across: 22 mm

82 999778002 - 04/2023
User Information Dokaflex table Article list

[kg] Article N° [kg] Article N°

Multi-trip packaging Doka accessory box 106.4 583010000


Doka-Kleinteilebox
Timber parts varnished yellow
Doka skeleton transport box 1.70x0.80m 87.0 583012000
Doka-Gitterbox 1,70x0,80m Steel parts galvanised
Galvanised Length: 154 cm
Height: 113 cm Width: 83 cm
Height: 77 cm

Bolt-on castor set B 33.6 586168000


Anklemm-Radsatz B
Painted blue
Doka multi-trip transport box 1.20x0.80m 70.0 583011000
Doka-Mehrwegcontainer 1,20x0,80m
Galvanised
Height: 78 cm

Multi-trip transport box partition 0.80m 3.7 583018000


Multi-trip transport box partition 1.20m 5.5 583017000
Mehrwegcontainer Unterteilung
Steel parts galvanised
Timber parts varnished yellow

Doka multi-trip transport box 1.20x0.80x0.41m 42.5 583009000


Doka-Mehrwegcontainer 1,20x0,80x0,41m
Galvanised

Doka stacking pallet 1.55x0.85m 41.0 586151000


Doka-Stapelpalette 1,55x0,85m
Galvanised
Height: 77 cm

Doka stacking pallet 1.20x0.80m 38.0 583016000


Doka-Stapelpalette 1,20x0,80m
Galvanised
Height: 77 cm

999778002 - 04/2023 83
Near to you, worldwide

Doka is one of the world leaders in developing, manu- technical support are provided swiftly and profession-
facturing and distributing formwork technology for use in ally.
all fields of the construction sector. An enterprise forming part of the Umdasch Group, the
With more than 160 sales and logistics facilities in over Doka Group employs a worldwide workforce of more
70 countries, the Doka Group has a highly efficient dis- than 6000.
tribution network which ensures that equipment and

www.doka.com/dokaflex-table

Doka GmbH | Josef Umdasch Platz 1 | 3300 Amstetten | Austria | T +43 7472 605-0 | F +43 7472 66430 | [email protected] | www.doka.com 999778002 - 04/2023

You might also like