This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles

for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Designation: B221M − 21

Standard Specification for

Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire,
Profiles, and Tubes (Metric)1
This standard is issued under the fixed designation B221M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.

1. Scope* mendations issued by the World Trade Organization Technical

1.1 This specification covers aluminum and aluminum-alloy Barriers to Trade (TBT) Committee.
extruded bars, rods, wires, profiles, and tubes in the aluminum
2. Referenced Documents
alloys (Note 1) and tempers shown in Table 2.
2.1 The following documents of the issue in effect on the
NOTE 1—Throughout this specification the use of the term alloy in the
date of material purchase form a part of this specification to the
general sense includes aluminum as well as aluminum alloy.
NOTE 2—For rolled or cold-finished bars and rods refer to Specification extent referenced herein:
B211/B211M, for drawn seamless tube used in pressure applications,
2.2 ASTM Standards:2
Specification B210/B210M, for structural pipe and tube, Specification
B429/B429M, and for seamless pipe and tube used in pressure
B210/B210M Specification for Aluminum and Aluminum-
applications, Specification B241/B241M. Alloy Drawn Seamless Tubes

iTeh Standards B211/B211M Specification for Aluminum and Aluminum-

NOTE 3— Pipe and tube products listed in this specification are intended
for general purpose applications. This specification may not address the
Alloy Rolled or Cold Finished Bar, Rod, and Wire
manufacturing processes, integrity testing, and verification required for
B234M Specification for Aluminum and Aluminum-Alloy
(https://standards.iteh.ai)
fluid-carrying applications involving pressure. See Specification B210/
Drawn Seamless Tubes for Surface Condensers,
B210M, B241/B241M, or both as appropriate for seamless pipe and tube
Evaporators, and Heat Exchangers (Metric)
used in fluid-carrying applications involving pressure. See Specification

Document Preview B241/B241M Specification for Aluminum and Aluminum-

B234M, as appropriate, for use in surface condensers, evaporators, and
heat exchangers. Alloy Seamless Pipe and Seamless Extruded Tube
1.2 Alloy and temper designations are in accordance with B429/B429M Specification for Aluminum-Alloy Extruded
ANSI H35.1/H35.1M. The equivalent Unified Numbering Structural Pipe and Tube
ASTM
System alloy designations are those of Table 1 preceded B221M-21
by A9, B557M Test Methods for Tension Testing Wrought and Cast
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
for example, A91100 for Aluminum 1100 in accordance with Aluminum- and Magnesium-Alloy Products (Metric)
Practice E527. B594 Practice for Ultrasonic Inspection of Aluminum-Alloy
Wrought Products
1.3 For acceptance criteria for inclusion of new aluminum
B660 Practices for Packaging/Packing of Aluminum and
and aluminum alloys in this specification, see Annex A2.
Magnesium Products
1.4 This specification is the metric counterpart of Specifi- B666/B666M Practice for Identification Marking of Alumi-
cation B221. num and Magnesium Products
1.5 The values stated in SI are to be regarded as standard. B807/B807M Practice for Extrusion Press Solution Heat
No other units of measurement are included in this specifica- Treatment for Aluminum Alloys
tion. B881 Terminology Relating to Aluminum- and Magnesium-
1.6 This international standard was developed in accor- Alloy Products
dance with internationally recognized principles on standard- B918/B918M Practice for Heat Treatment of Wrought Alu-
ization established in the Decision on Principles for the minum Alloys
Development of International Standards, Guides and Recom- B945 Practice for Aluminum Alloy Extrusions Press Cooled
from an Elevated Temperature Shaping Process for Pro-
duction of T1, T2, T5 and T10–Type Tempers
1
This specification is under the jurisdiction of ASTM Committee B07 on Light
Metals and Alloys and is the direct responsibility of Subcommittee B07.03 on
2
Aluminum Alloy Wrought Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2021. Published November 2021. Originally contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
approved in 1979. Last previous edition approved in 2013 as B221M – 13. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/B0221M-21. the ASTM website.

*A Summary of Changes section appears at the end of this standard

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

1
 B221M − 21
TABLE 1 Chemical Composition Limits A,B,C
Manga- Magne- Other ElementsD
Alloy Silicon Iron Copper Chromium Zinc Titanium Vanadium Aluminum
nese sium Each TotalE
1060 0.25 0.35 0.05 0.03 0.03 ... 0.05 0.03 0.05 0.03 ... 99.60 minF
1100G 0.95 Si + Fe 0.05–0.20 0.05 ... ... 0.10 ... ... 0.05 0.15 99.00 minF
2014H 0.50–1.2 0.7 3.9–5.0 0.40–1.2 0.20–0.8 0.10 0.25 0.15 ... 0.05 0.15 rem
2024H 0.50 0.50 3.8–4.9 0.30–0.9 1.2–1.8 0.10 0.25 0.15 ... 0.05 0.15 rem
2219I 0.20 0.30 5.8–6.8 0.20–0.40 0.02 ... 0.10 0.02–0.10 0.05–0.15 0.05 0.15 rem
3003 0.6 0.7 0.05–0.20 1.0–1.5 ... ... 0.10 ... ... 0.05 0.15 rem
Alclad 3003 ... 3003 Clad with 7072 Alloy ... ... ... ... ... ... ... ...
3004 0.30 0.7 0.25 1.0–1.5 0.8–1.3 ... 0.25 ... ... 0.05 0.15 rem
3102 0.40 0.7 0.10 0.05–0.40 ... ... 0.30 0.10 ... 0.05 0.15 rem
5052 0.25 0.40 0.10 0.10 2.2–2.8 0.15–0.35 0.10 ... ... 0.05 0.15 rem
5083 0.40 0.40 0.10 0.40–1.0 4.0–4.9 0.05–0.25 0.25 0.15 ... 0.05 0.15 rem
5086 0.40 0.50 0.10 0.20–0.7 3.5–4.5 0.05–0.25 0.25 0.15 ... 0.05 0.15 rem
5154G 0.25 0.40 0.10 0.10 3.1–3.9 0.15–0.35 0.20 0.20 ... 0.05 0.15 rem
5454 0.25 0.40 0.10 0.50–1.0 2.4–3.0 0.05–0.20 0.25 0.20 ... 0.05 0.15 rem
5456 0.25 0.40 0.10 0.50–1.0 4.7–5.5 0.05–0.20 0.25 0.20 ... 0.05 0.15 rem
6005 0.6–0.9 0.35 0.10 0.10 0.40–0.6 0.10 0.10 0.10 ... 0.05 0.15 rem
6005AJ 0.50–0.9 0.35 0.30 0.50 0.40–0.7 0.30 0.20 0.10 ... 0.05 0.15 rem
6013 0.6-1.0 0.50 0.6-1.1 0.20-0.8 0.8-1.2 0.10 0.25 0.10 { 0.05 0.15 rem
6020K 0.40–0.9 0.50 0.30–0.9 0.35 0.6–1.2 0.15 0.20 0.15 ... 0.05 0.15 rem
6026L 0.6–1.4 0.7 0.20–0.50 0.20–1.0 0.6–1.2 0.30 0.30 0.20 ... 0.05 0.15 rem
6041M 0.50–0.9 0.15–0.7 0.15–0.6 0.05–0.20 0.8–1.2 0.05–0.15 0.25 0.15 ... 0.05 0.15 rem
6042N 0.50–1.2 0.7 0.20–0.6 0.40 0.7–1.2 0.04–0.35 0.25 0.15 ... 0.05 0.15 rem
6060 0.30–0.6 0.10–0.30 0.10 0.10 0.35–0.6 0.05 0.15 0.10 ... 0.05 0.15 rem
6061O 0.40–0.8 0.7 0.15–0.40 0.15 0.8–1.2 0.04–0.35 0.25 0.15 ... 0.05 0.15 rem
6063 0.20–0.6 0.35 0.10 0.10 0.45–0.9 0.10 0.10 0.10 ... 0.05 0.15 rem
6064P 0.40–0.8 0.7 0.15–0.40 0.15 0.8–1.2 0.05–0.14 0.25 0.15 ... 0.05 0.15 rem
6066 0.9–1.8 0.50 0.7–1.2 0.6–1.1 0.8–1.4 0.40 0.25 0.20 ... 0.05 0.15 rem
6070 1.0–1.7 0.50 0.15–0.40 0.40–1.0 0.50–1.2 0.10 0.25 0.15 ... 0.05 0.15 rem
6082 0.7–1.3 0.50 0.10 0.40–1.0 0.6–1.2 0.25 0.20 0.10 ... 0.05 0.15 rem

iTeh Standards
6105 0.6–1.0 0.35 0.10 0.15 0.45–0.8 0.10 0.10 0.10 ... 0.05 0.15 rem
6162 0.40–0.8 0.50 0.20 0.10 0.7–1.1 0.10 0.25 0.10 ... 0.05 0.15 rem
6262Q 0.40–0.8 0.7 0.15–0.40 0.15 0.8–1.2 0.04–0.14 0.25 0.15 ... 0.05 0.15 rem

(https://standards.iteh.ai)
6351 0.7–1.3 0.50 0.10 0.40–0.8 0.40–0.8 ... 0.20 0.20 ... 0.05 0.15 rem
6360 0.35–0.8 0.10–0.30 0.15 0.02–0.15 0.25–0.45 0.05 0.10 0.10 ... 0.05 0.15 rem
6463 0.20–0.6 0.15 0.20 0.05 0.45–0.9 ... 0.05 ... ... 0.05 0.15 rem
6560 0.30–0.7 0.10–0.30 0.05–0.20 0.20 0.20–0.6 0.05 0.15 0.10 ... 0.05 0.15 rem
7005R
7072S
7075T
0.35

0.40
0.40
0.7 Si + Fe
0.50
Document Preview
0.10
0.10
1.2–2.0
0.20–0.7
0.10
0.30
1.0–1.8
0.10
2.1–2.9
0.06–0.20
...
0.18–0.28
4.0–5.0
0.8–1.3
5.1–6.1
0.01–0.06
...
0.20
...
...
...
0.05

0.05
0.15

0.15
rem
rem
rem
7116U 0.15 0.30 0.50–1.1 0.05 0.8–1.4 ... 4.2–5.2 0.05 0.05 0.05 0.15 rem
7129U 0.15 0.30 0.50–0.9 0.10 1.3–2.0 0.10 4.2–5.2 0.05 0.05 0.05 0.15 rem
A
ASTM B221M-21
Limits are in weight percent maximum unless shown as a range, or stated otherwise.
B
C
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
Analysis shall be made for the elements for which limits are shown in this table.
For the purpose of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the
last right-hand place of the figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.
D
Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not
specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser
establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered
nonconforming.
E
Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.
F
The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the
second decimal before determining the sum.
G
Be 0.0003 max for welding electrode, welding rod, and filler wire.
H
Upon agreement between the purchaser and the producer or supplier, a Zr + Ti limit of 0.20 % max is permitted. Properties in Specification (Table 2) are not based on
the Zirconium and Titanium algorithm.
I
Zirconium, 0.10–0.25 %. The total for other elements does not include zirconium.
J
Manganese plus chromium shall total 0.12–0.50.
K
Lead 0.05 % max, Tin 0.9–1.5 %.
L
Bismuth 0.50–1.5 %, Lead 0.4 % max, Tin 0.05 % max.
M
Bismuth 0.30–0.9 %, Tin 0.35–1.2 %.
N
Bismuth 0.20–0.8 % Lead 0.15–0.40 %.
O
In 1965 the requirements for 6062 were combined with those for 6061 by revising the minimum chromium from “0.15 %” to“0.04 %.” This action cancelled Alloy 6062.
P
Bismuth 0.50–0.7 %, Lead 0.20–0.04 %,
Q
Bismuth and lead shall be 0.40–0.7 % each.
R
Zirconium 0.08–0.20 %. The total for other elements does not include zirconium.
S
Composition of cladding alloy applied during the course of manufacture. Samples from finished tube shall not be required to conform to these limits.
T
Upon agreement between the purchaser and the producer or supplier, a Zr + Ti limit of 0.25 % max is permitted. Properties in Specification (Table 2) are not based on
the Zirconium and Titanium algorithm.
U
Gallium 0.03 % max.

2
 B221M − 21
TABLE 2 Tensile Property LimitsA,B
Specified Section or Tensile Strength, Yield Strength Elongation,D
Area, mm2 %, min
Wall Thickness, mm MPa (0.2 %)
Temper Product TypeC in 50 ×
in
over incl over incl min max min max Diameter
50 mm
(5.56=A)
Aluminum 1060E
O Extruded Tube all all 60 95 15 ... 25 22

H112 Extruded Tube all all 60 ... 15 ... 25 22

Aluminum 1100E
O Extruded Tube all all 75 105 20 ... 25 22

H112 Extruded Tube all all 75 ... 20 ... 25 22

Alloy 2014E
Extruded Wire, Rod, Bar,
O all all ... 205 ... 125 12 10
Profiles, and Tube

T4
T4510F
T4511F
J Extruded Wire, Rod, Bar,
Profiles, and Tube
all all 345 ... 240 ... 12 10

Extruded Wire, Rod, Bar,

T42G all all 345 ... 200 ... 12 10
Profiles, and Tube

T6
T6510F
T6511F
J Extruded Wire, Rod, Bar,
Profiles, and Tube
5iTeh Standards
...
12.50
18.00
18.00
12.50
18.00
...
...
all
all
...
16 000
16 000
20 000
415
440
470
470
.
.
.
.
.
.
.
.
.
.
.
.
365
400
415
400
.
.
.
.
.
.
.
.
.
.
.
.
7
...
...
...
6
6
6
5

T62G
(https://standards.iteh.ai)
H
Extruded Wire, Rod, Bar,
Profiles, and Tube
...
18.00
18.00
...
all
...
...
16 000
415
415
...
...
365
365
...
...
7
...
6
6

Document Preview
18.00 ... 16 000 20 000 415 ... 365 ... ... 5

Alloy 2024E
Extruded Wire, Rod, Bar,
O all all ... 240 ... 130 12 10
and Profiles
ASTM B221M-21
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
J 5
... 6.30 all 395 ... 290 ... 12 ...
T3 6.30 18.00 all 415 . . . 305 . . . 12 10
Extruded Wire, Rod, Bar,
T3510F and Profiles
18.00 35.00 all 450 . . . 315 . . . ... 9
T3511F 35.00 ... ... 16 000 485 . . . 360 . . . ... 9
35.00 ... 16 000 20 000 470 . . . 330 . . . ... 7

J 5
... 6.30 all 395 . . . 290 . . . 10 ...
T3 6.30 18.00 all 415 . . . 305 . . . 10 9
T3510F Extruded Tube 18.00 35.00 all 450 . . . 315 . . . ... 9
T3511F 35.00 ... ... 16 000 485 . . . 330 . . . ... 9
35.00 ... 16 000 20 000 470 . . . 315 . . . ... 7

5
... 18.00 all 395 . . . 260 . . . 12 10
Extruded Wire, Rod, Bar, 18.00 35.00 all ... 395 . . . 260 . . . ... 9
T42G
Profiles, and Tube 35.00 ... ... 16 000 395 . . . 260 . . . ... 9
35.00 ... 16 000 20 000 395 . . . 260 . . . ... 7

T81
T8510F
T8511F
J Extruded Wire, Rod, Bar,
Profiles, and Tube
H 1.20
6.30
35.00
6.30
35.00
...
all
all
... 20 000
440
455
455
...
...
...
385
400
400
...
...
...
4
5
...
...
4
4

3
 B221M − 21
TABLE 2 Continued
Specified Section or Tensile Strength, Yield Strength Elongation,D
Area, mm2 %, min
Wall Thickness, mm MPa (0.2 %)
Temper Product TypeC in 50 ×
in
over incl over incl min max min max Diameter
50 mm
(5.56=A)
Alloy 2219E
Extruded Wire, Rod, Bar,
O all all ... 220 ... 125 12 10
Profiles, and Tube

T31
T3510F
T3511F
J Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
12.50
12.50
80.00
...
16 000
16 000
290
310
...
...
180
185
...
...
14
...
12
12

T62G
Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
25.00
25.00
...
...
16 000
20 000
370
370
...
...
250
250
...
...
6
...
5
5

T81
T8510F
T8511F
J Extruded Wire, Rod, Bar,
Profiles, and Tube
... 80.00 ... 16 000 400 ... 290 ... 6 5

Alloy 3003E
Extruded Wire, Rod, Bar,
O all all 95 130 35 ... 25 22
Profiles, and Tube

Extruded Wire, Rod, Bar,

iTeh Standards
H112 all all 95 ... 35 ... ... ...
and Profiles

H112 Extruded Tube all all 95 ... 35 ... 25 22

(https://standards.iteh.ai)
Alclad Alloy 3003
O Extruded Tube all all 90 125 30 ... 25 22

Document Preview
H112 Extruded Tube all all 90 ... 30 ... 25 22
Alloy 3004E
O Extruded Tube all all 160 200 60 ... ... ...
Alloy 3102
H112 Extruded Tube 0.63 1.20 all 75 125 30 ... 25 ...
Alloy 5052E
O Extruded Tube all ASTM B221M-21 170 all
240 70 ... ... ...
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
Extruded Wire, Rod, Bar,
Alloy 5083E
O ... 130.00 ... 20 000 270 350 110 ... 14 12
and Profiles

Extruded Wire, Rod, Bar,

H111 ... 130.00 ... 20 000 275 ... 165 ... 12 10
and Profiles

Extruded Wire, Rod, Bar,

H112 ... 130.00 ... 20 000 270 ... 110 ... 12 10
and Profiles

O Extruded Tube 70H ... 20 000 270 350 110 ... 14 12

H
H111 Extruded Tube 70 ... 20 000 275 ... 165 ... 12 10

H
H112 Extruded Tube 70 ... 20 000 270 ... 110 ... 12 10
Alloy 5086E
Extruded Wire, Rod, Bar,
O ... 130.00 ... 20 000 240 315 95 ... 14 12
and Profiles

Extruded Wire, Rod, Bar,

H111 ... 130.00 ... 20 000 250 ... 145 ... 12 10
and Profiles

Extruded Wire, Rod, Bar,

H112 ... 130.00 ... 20 000 240 ... 95 ... 12 10
and Profiles

O Extruded Tube 70H ... 20 000 240 315 95 ... 14 12

H
H111 Extruded Tube 70 ... 20 000 250 ... 145 ... 12 10

H
H112 Extruded Tube 70 ... 20 000 240 ... 95 ... 12 10

4
 B221M − 21
TABLE 2 Continued
Specified Section or Tensile Strength, Yield Strength Elongation,D
Area, mm2 %, min
Wall Thickness, mm MPa (0.2 %)
Temper Product TypeC in 50 ×
in
over incl over incl min max min max Diameter
50 mm
(5.56=A)
Alloy 5154
Extruded Wire, Rod, Bar,
O all all 205 285 75 ... ... ...
Profiles, and Tube

Extruded Wire, Rod, Bar,

H112 all all 205 ... 75 ... ... ...
Profiles, and Tube
Alloy 5454E
Extruded Wire, Rod, Bar,
O ... 130.00 ... 20 000 215 285 85 ... 14 12
and Profiles

Extruded Wire, Rod, Bar,

H111 ... 130.00 ... 20 000 230 ... 130 ... 12 10
and Profiles

Extruded Wire, Rod, Bar,

H112 ... 130.00 ... 20 000 215 ... 85 ... 12 10
and Profiles

O Extruded Tube 70H 20 000 215 285 85 ... 14 12

H
H111 Extruded Tube 70 20 000 230 ... 130 ... 12 10

H112 Extruded Tube 70H 20 000 215 ... 85 ... 12 10

Alloy 5456E
Extruded Wire, Rod, Bar,
O ... 120.00 ... 20 000 285 365 130 ... 14 12
and Profiles

Extruded Wire, Rod, Bar,

H111 ... 120.00 ... 20 000 290 ... 180 ... 12 10

iTeh Standards
and Profiles

Extruded Wire, Rod, Bar,

H112 ... 120.00 ... 20 000 285 ... 130 ... 12 10

(https://standards.iteh.ai)
and Profiles

O Extruded Tube 70I 20 000 285 365 130 ... 14 12

H111

H112
Document Preview
Extruded Tube

Extruded Tube
70

70I
I
20 000

20 000
290

285
...

...
180

130
...

...
12

12
10

10
Alloy 6005
Extruded Wire, Rod, Bar,
T1
Profiles, and Tube ASTM
12.50 B221M-21
... all 170 ... 105 ... 16 14

https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
T5
Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
3.20
3.20
25.00
all
all
260
260
...
...
240
240
...
...
8
10
...
9

Alloy 6005A
Extruded Wire, Rod, Bar,
T1 ... 6.30 all 170 ... 100 ... 15 ...
Profiles, and Tube

T5
Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
6.30
6.30
25.00
all
all
260
260
...
...
215
215
...
...
7
9
...
8

T61
Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
6.30
6.30
25.00
all
all
260
260
...
...
240
240
...
...
8
10
...
9

Alloy 6013
5.00 12.50 all 340 ... 315 ... 8 ...
Extrusion, Rod,
T6, T6511F 12.50 20.00 all 340 ... 315 ... ... 7
and Seamless Tube
20.00 50.00 all 340 ... 310 ... ... 7
Alloy 6020
T6511F Extruded Rod and Bar 80.00 160.00 all 260 ... 240 ... ... 9

5
 B221M − 21
TABLE 2 Continued
Specified Section or Tensile Strength, Yield Strength Elongation,D
Area, mm2 %, min
Wall Thickness, mm MPa (0.2 %)
Temper Product TypeC in 50 ×
in
over incl over incl min max min max Diameter
50 mm
(5.56=A)
Alloy 6026
T6, T6510,F
Extruded Profiles 5.00 40.00 all 340 ... 260 ... 6 8
T6511F

T6, T6510,F
Extruded Tube 10.00 30.00 all 340 ... 260 ... 6 8
T6511F

T6, T6510,F
T6511F
Extruded Bar, Rod, and
Wire
H 30.00
140.00
200.00
140.00
200.00
250.00
all
all
all
370
340
300
...
...
...
300
250
200
...
...
...
6
6
6
8
8
8

Alloy 6041
F Extruded Rod, Bar, and
T6, T6511 10.00 50.00 all 310 ... 275 ... 10 9
Profiles
Alloy 6042
Extruded Rod, Bar, and 10.00 12.50 all 260 ... 240 ... 10 ...
T5, T5511F
Profiles 12.50 50.00 all 260 ... 240 ... ... 9
Alloy 6060
T51 Extruded Profiles ... 3.20 all 150 ... 110 ... 8 ...

T61 Extruded Profiles H ...

3.20
3.20
25.00
all
all
205
205
...
...
170
170
...
...
8
10
...
9

O iTeh Standards
Extruded Wire, Rod, Bar,
Profiles, and Tube
all
Alloy 6061E
all ... 150 ... 110 16 14

T1 (https://standards.iteh.ai)
Extruded Wire, Rod, Bar,
Profiles, and Tube
... 16.00 all 180 ... 95 ... 16 14

T4, T4510,F
J Document Preview
Extruded Wire, Rod, Bar
all all 180 ... 110 ... 16 14
T4511F Profiles, and Tube

ASTM B221M-21
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
T42 G Extruded Wire, Rod, Bar,
Profiles, and Tube
all all 180 ... 85 ... 16 14

Extruded Wire, Rod, Bar,

T51 ... 16.00 all 240 ... 205 ... 8 7
Profiless, and Tube

T6, T62,G
T6510,F T6511F J Extruded Wire, Rod, Bar,
Profiles and Tube
H ...
6.30
6.30
...
all
all
260
260
...
...
240
240
...
...
8
10
...
9

Alloy 6063
Extruded Wire, Rod, Bar,
O all all ... 130 ... ... 18 16
Profiles, and Tube

Extruded Wire, Rod, Bar, ... 12.50 all ... 115 ... 60 ... 12 10
T1
Profiles, and Tube 12.50 25.00 all ... 110 ... 55 ... ... 10

Extruded Wire, Rod, Bar, ... 12.50 all 130 ... 70 ... 14 12
T4, T42G
Profiles, and Tube 12.50 25.00 all 125 ... 60 ... ... 12

Extruded Wire, Rod, Bar, ... 12.50 all 150 ... 110 ... 8 7
T5
Profiles, and Tube 12.50 25.00 all 145 ... 105 ... ... 7

Extruded Wire, Rod, Bar,

T52 ... 25.00 all 150 205 110 170 8 7
Profiles, and Tube

Extruded Wire, Rod, Bar, ... 3.20 all 225 ... 205 ... 8 ...
T54
and Profiles 3.20 12.50 all 225 ... 205 ... 10 ...

6
 B221M − 21
TABLE 2 Continued
Specified Section or Tensile Strength, Yield Strength Elongation,D
Area, mm2 %, min
Wall Thickness, mm MPa (0.2 %)
Temper Product TypeC in 50 ×
in
over incl over incl min max min max Diameter
50 mm
(5.56=A)
Alloy 6063 (Continued)
Extruded Wire, Rod, Bar, ... 3.20 all 205 ... 170 ... 8 ...
T6, T62G
Profiles, and Tube 3.20 25.0 all 205 ... 170 ... 10 9

Extruded Wire, Rod, Bar,

T65 ... 5.00 all 250 ... 230 ... 7 ...
and Profiles
Alloy 6064
Extruded Wire, Rod, Bar,
T6 5.00 80.00 all 290 ... 260 ... 10 9
and Profiles

Extruded Wire, Rod, Bar,

T6511F 5.00 80.00 all 290 ... 260 ... 10 9
and Profiles
Alloy 6066
Extruded Wire, Rod, Bar,
O all all ... 200 ... 125 16 14
Profiles, and Tube

T4, T4510,F
T4511F J Extruded Wire, Rod, Bar,
Profiles, and Tube
all all 275 ... 170 ... 14 12

Extruded Wire, Rod, Bar,

T42G all all 275 ... 165 ... 14 12
Profiles, and Tube

T6, T6510,F
T6511F J iTeh Standards
Extruded Wire, Rod, Bar,
Profiles, and Tube
all all 345 ... 310 ... 8 7

T62G
(https://standards.iteh.ai)
Extruded Wire, Rod, Bar,
all all 345 ... 290 ... 8 7

Document Preview
Profiles, and Tube
Alloy 6070
Extruded Wire, Rod, Bar,
T6, T62G ... 80.00 ... 20 000 330 ... 310 ... 6 5
Profiles, and Tube
Alloy 6082

Extruded Wire, Rod, Bar,

and Profiles
H
5.00 ASTM

150.00
20.00 B221M-21
150.00
200.00
all
all
all
310
310
280
...
...
...
260
260
240
...
...
...
6
https://standards.iteh.ai/catalog/standards/sist/1ae96a8c-52ae-437e-975a-19df22380a04/astm-b221m-21
T6, T6511 F
20.00
8
8
8

T6 Extruded Tube 5.00 25.00 all 310 ... 260 ... 8 10

Alloy 6105
Extruded Wire, Rod, Bar,
T1 ... 12.50 all 170 ... 105 ... 16 14
Profiles, and Tube

Extruded Wire, Rod, Bar,

T5 ... 12.50 all 260 ... 240 ... 8 7
Profiles, and Tube

Extruded Wire, Rod, Bar,

T6 ... 12.50 all 260 ... 240 8 7
and Profiles
Alloy 6162
T5, T5510,F Extruded Wire, Rod, Bar.
... 25.00 all 255 ... 235 ... 7 6
T5511F Profiles, and Tube

T6, T6510,F
T6511F
Extruded Wire, Rod, Bar,
Profiles, and Tube
H ...
6.30
6.30
12.50
all
all
260
260
...
...
240
240
...
...
8
10
...
9

Alloy 6262

T6, T62,G
T6510,F T6511F J Extruded Wire, Rod, Bar,
Profiles and Tube
all all 260 ... 240 ... 10 9