D1wwed02e DPC Ing Kbs New 28621

DPC
Series
Pre-compensated Load Sensing Sectional Valves
DPC Series
Additional information
This catalogue shows the product in the most standard configurations.
Please contact Sales Dpt. for more detailed information or special request.
WARNING!
All specifications of this catalogue refer to the standard product at this date.
Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN

5th edition May 2015
INCORRECT USE OF THE PRODUCT.
2 D1WWED02E
DPC Series General informations
____________________________________________________________________________________________
The DPC Series
The DPC Series is a family of open/closed center pre-pressure compensated sectional valves designed specifically for Mobile
Applications. The DPC series provides exceptional controllability, efficiency and flexibility for applications requiring up to
240 l/min (63.4 US gpm) flow rate. DPC Series is available in two different sizes: DPC130 and DPC200.
DPC130 DPC200
_________________________________________________________________________
The Load Sensing technology
Thanks to the use of specially designed pumps and control valves, the Load Sensing principle can be considered the most com-
prehensive means of creating a flexible hydraulic circuit that can adapt to the various operating conditions demanded by users.
The main feature of this principle is that the flow rate to the user is proportional to the spool position under any operating condi-
tion, regardless of the resistance encountered by the user (pressure) and the number of levers activated (exceeding the pump’s
total flow rate, a condition here in after defined as saturation, is the only limitation).
Therefore, with the LS systems, there is a specific correspondence between the position of the control lever and the movement
speed of the user, cylinder or hydraulic motor. This feature is particularly useful in the hydraulic handling machine sector (ex-
cavators, cranes, loaders, agricultural and forestry machinery) in which each movement phase has specific sequences that the
operator must control using memorised movements.
Advantages and options

• Energy saving.
• Extension of parts service life.
• Lower energy dissipation.
• Noise reduction.
• Available to create a single-pump circuit (compared with the use of multiple-pump circuits in which each pump is dedicated
to different actuators to be operated simultaneously).
Real energy savings can be obtained above all when the DPC directional valves operate together with variable displacement Load
Sensing pumps. When the DPC valve is utilised with fixed displacement pumps, the previously mentioned movement indepen-
dence and repeatability features are guaranteed, but energy savings will be limited.
For special options contact Sales Dept.
D1WWED02E 3
General informations DPC Series
Working conditions _ _____________________________________________________________________________________
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s - 46 cSt viscosity at 40°C -
104°F temperature.
DPC130 DPC200
on inlet port with compensator 150 l/min - 39.6 US gpm 260 l/min - 68.7 US gpm
@ stand-by (margin pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
Nominal flow rating on working ports with compensator 100 l/min - 26.4 US gpm 200 l/min - 52.8 US gpm
(open center circuit) @ stand-by (margin pressure) @ 7 bar - 102 ps @ 7 bar - 102 ps
on working ports without compensator 130 l/min - 34.3US gpm 240 l/min - 63.4 US gpm
@ stand-by (margin pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
inlet port P 315 bar (2) - 4500 psi (2) 350 bar (1) - 5100 psi (1)
Max. pressure
working ports A and B 315 bar ( ) - 4500 psi ( )
2 2
420 bar (1) - 6100 psi (1)
on outlet port T 25 bar - 363 psi 25 bar - 363 psi
Back pressure (max.)
on drain port L 2.5 bar - 36 psi 2.5 bar - 36 psi
Standard internal leakage ∆p=100 bar - 1450 psi 16 cm /min - 0.98 in /min
3 3
20 cm3/min - 1.22 in3/min
A(B)->T with port valves, ∆p=100 bar - 1450 psi 21 cm3/min - 1.28 in3/min 25 cm3/min - 1.53 in3/min
Fluid Mineral oil
with seals NBR (BUNA-N) from -20°C to 80°C - from -4°F to 176°F
Fluid temperature range
with seals FPM (VITON) from -20°C to 100°C - from -4°F to 212°F
operating range from 15 to 75 mm2/s - from 15 to 75 cSt
Viscosity min. 12 mm2/s - 12 cSt
max. 400 mm2/s - 400 cSt
Contamination level max. -/18/15 - ISO 4406 - NAS 1638 class 9
with mechanical devices from -40°C to 60°C - from -40°F to 140°F
Environmental temperature
with hydraulic/pneumatic devices from -30°C to 60°C - from -22°F to 140°F
for working conditions
with electric/electrohydraulic devices from -20°C to 50°C - from -4°F to 122°F
NOTES: (1) According to NFPA T 2.6.1., fatigue rating verified for 1 million cycles on 6 sample valves with test Pressure = 1.23 x Max.
pressure indicated - (2) Intermittent pressure at max. 250,000 cycles with specific internal testing.
4 D1WWED02E
DPC Series General informations
_________________________________________________________________________________________
Standard threads
REFERENCE STANDARD
BSP UN-UNF NPTF Flange connection
THREAD ISO 228/1 ISO 263 ISO 6162
ANSI B1.20.3
ACCORDING TO BS 2779 ANSI B1.1 unified SAE J518
CAVITY ISO 1179 11926

DIMENSION SAE J1926 J476a SAE J518 code 61 (3)
ACCORDING TO DIN 3852-2 shape X or Y ISO 6162-1 (4)
NOTEs (3): Standard pressure series - (4): For pressure up to 350 bar (5100 psi)
DPC130 DPC200
PORTS
BSP UN-UNF BSP UN-UNF Flange connection (bolts threading)
THREADING
ISO 6162-1 type 1 SAE J518 code 61
Inlet P G 3/4 1 1/16-12 (SAE 12) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
Ports A and B G 1/2 7/8-14 (SAE10) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
Outlet T G 3/4 1 1/16-12 (SAE 12) G 1-1/4 1 5/8-12 (SAE 20) DN 25 (M10) 1 (3/8-16 UNC)
Load Sensing LS G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
Pilot V1 G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
depends on inlet section type:
Pilot V2 M14x1.5 (5)
see pages from 14 to 17 (5) see BSP threading see UN-UNF threading
Drain L G 1/4 7/16-20 (SAE 4) G 1/4 7/16-20 (SAE 4)
Pressure gauge M G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
Hydraulic control ports G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
NOTE ( ): ATTENTION! pilot port V2 requires dedicate joints, please see Inlet section pages.
5
D1WWED02E 5
Index DPC Series
Contents
DPC130
Dimensional data and performance. . . . . . . . . . . . . . . . . . page 8
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Complete sections ordering codes. . . . . . . . . . . . . . . . . . . . . . 10
• Inlet section
Inlet section parts ordering codes. . . . . . . . . . . . . . . page 12
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 14
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . . . . . . 19
Solenoid operated unloading valve . . . . . . . . . . . . . . . . . . 19
• Working section
Working section parts ordering codes . . . . . . . . . . . . page 20
Spools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
"A" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 29
Electrohydraulic controls. . . . . . . . . . . . . . . . . . . . . . . . . 31
"B" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 36
Port valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
• Outlet section
Outlet section parts ordering codes. . . . . . . . . . . . . . page 38
Drain options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DPC200
Dimensional data and performance. . . . . . . . . . . . . . . . . page 40
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Complete sections ordering codes. . . . . . . . . . . . . . . . . . . . . . 42
• Inlet section
Inlet section parts ordering codes. . . . . . . . . . . . . . . page 44
Pressure reducing valve. . . . . . . . . . . . . . . . . . . . . . . . . . 48
Solenoid operated unloading valve . . . . . . . . . . . . . . . . . . 48
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . . . . . . 49
• Working section
Working section parts ordering codes . . . . . . . . . . . . page 50
Spools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
"A" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 56
Electrohydraulic controls. . . . . . . . . . . . . . . . . . . . . . . . . 58
"B" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 62
Port valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
• Outlet section
Outlet section parts ordering codes. . . . . . . . . . . . . . page 65
Drain options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6 D1WWED02E
DPC Series Index
Special configurations
Connection between DPC Series valves. . . . . . . . . . . page 68
Accessories
Coils and connectors. . . . . . . . . . . . . . . . . . . . . . . . page 70
Istallation and maintenace . . . . . . . . . . . . . . . page 72
Appendices
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 74
D1WWED02E 7
DPC130 DPC Series
Dimensional data and performance _________________________________________________________________
81 48 50 53
170.5 3.19 2.01 1.97 2.09
6.73 37.1 16 16 10
54.5 1.46 0.63 0.63 0.39
2.15
Ø 8.5
2.76
70
Ø 0.33
5
0.31
0.197
0.19
4.7
8
0.43
11
P
33.5
1.32
L A2 A1
43.5
2.01
4.57
116
10.98
3.94
100
279
1.30
33
45.5
1.79
LS B2 B1
33.5
1.32
0.35
9
0.31
8
130.4 8 E
5.13 0.31
152 F
5.98
P⇒T Pressure drop inlet compensator

(margin pressure)
161020061 product code 0 8 16 24 32 (US gpm)
PA1501568/004 production allotment 40
(psi)
(bar) 500
30
400
Pressure
20 300
200
E F Weight 10
Type 100
mm in mm in Kg lb
0 0
DPC130/1 184 7.24 200 7.87 12.4 27.3 0 30 60 90 120 150 (l/min)
DPC130/2 232 9.13 248 9.76 19.4 42.8 Flow
DPC130/3 280 11.02 296 11.65 25.3 55.8

A(B)⇒T pressure drop
DPC130/4 328 12.91 344 13.54 31.0 68.3 (standard spool @ max.stroke)
DPC130/5 376 14.80 392 15.43 36.5 80.5 0 8 16 24 32 (US gpm)
40
(psi)
DPC130/6 424 16.69 440 17.32 42.6 93.9 without compensator
(bar) with compensator 500
26.4 US gpm
34.3 US gpm
DPC130/7 472 18.58 488 19.21 48.7 107.0

100 l/min
130 l/min
30
8th section 400
Pressure
DPC130/8 520 20.47 536 21.10 54.8 121.0

20 300
DPC130/9 568 22.36 584 22.99 60.9 134.0 1st section
200
DPC130/10 616 24.25 632 24.88 67.0 148.0 10
100
0 0
0 30 60 90 120 150 (l/min)
Flow
8 D1WWED02E
DPC Series DPC130
__________________________________________________________________________________________
Hydraulic circuit
Open center configuration example
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Open center circuit and one-side proportional electrohydraulic control with lever,
with unloader valve and pressure reducing valve, port valves arrangement on all
ports, LSAB port, internal pilot and external drain
Closed center configuration example
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Closed center circuit and one-side proportional electrohydraulic control
with lever, with unloader valve and pressure reducing valve, antishock and
anticavitation valves on all ports, L.S. relief valves on 2th section, LSAB ports,
internal pilot and external drain
D1WWED02E 9
DPC130 DPC Series
Complete sections ordering codes ___________________________________________________________________
DPC130 / 3 / BR21-S220-ELP / C10-1S8EZ3L1 / C10-1S8EZ3L1 /..... / RF30 - ...... - 12VDC - <SB20 - CVN>
Valve type 1 2 3 4 5 6
Nr. of working sections The valve is supplied painted,

as standard, with one coat of
Primer black antirust paint
7 2
Tie rods tightening

wrench 13 - 30 Nm (22 lbft)
10 D1WWED02E
DPC Series DPC130
___________________________________________________________________
Complete sections ordering codes
1 Inlet section * page 12 3 Outlet section * page 38

TYPE: DPC130/BR-S200-DSK CODE: 63420H000 For valve with mechanical control
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve, TYPE: DPC130/RF10 CODE: 634310001
pressure reducing valve and selector for open/closed center circuit DESCRIPTION: Without ports
Closed Center circuit For valve with hydraulic control
TYPE: DPC130/BN21-S220 CODE: 63422H003 TYPE: DPC130/RF20 CODE: 634310000
DESCRIPTION: With 3-way compensator and L.S. pressure relief DESCRIPTION: Without ports, internal drain
valve, without pressure reducing valve For valve with electrohydraulic control
TYPE: DPC130/BR21-S220-ELP-12VDC CODE: 63421H001 TYPE: DPC130/RF30 CODE: 634310002
DESCRIPTION: As previous, with pressure reducing valve, and 12VDC DESCRIPTION: Without ports, external drain L
solenoid operated unloader valve TYPE: DPC130/RC31 CODE: 634310012
TYPE: DPC130/BRF21-S250 CODE: 634250900 DESCRIPTION: With ports P1 and T1 (plugged), external drain L
DESCRIPTION: Without compensator, with pressure reducing valve TYPE: DPC130/RD31 CODE: 634310015
and L.S. pressure relief valve DESCRIPTION: With ports P1 and T1 (plugged), port LS1, external
TYPE: DPC130/BRSOG21(SF)-S220-ELN3-12VDC CODE: 63424H005 drain L
DESCRIPTION: Shut-off configuration, with pressure reducing valve
and L.S. pressure relief valve 4 Valve threading
TYPE: DPC130/BRS21-S220-ELP-12VDC CODE: 63423H003
Specify only if it is different from BSP standard (see page 5).
DESCRIPTION: Copy-Spool with dumper configuration, with 3-way
compensator, pressure reducing valve, L.S. pressure relief valve and
12VDC solenoid operated unloader valve 5 Voltage
Open Center circuit Specify the voltage of electric device
TYPE: DPC130/BN11-S220 CODE: 63422H004
DESCRIPTION: With 3-way compensator and L.S. pressure relief
6 Pump stand-by
valve, without pressure reducing valve
TYPE: DPC130/BR11-S220-ELP-12VDC CODE: 63421H002 This option must be specified only if valve is configured for Closed
DESCRIPTION: As previous, with pressure reducing valve, and 12VDC Center circuit, without local compensation and if the value is different
solenoid operated unloader valve from 11.5 bar (167 psi)
TYPE: DPC130/BRS11-S220-ELP-12VDC CODE: 63423H002
DESCRIPTION: Copy-Spool with dumper configuration, with 3-way 7 Assembling kit
compensator, pressure reducing valve, L.S. pressure relief valve and
CODE CODE DESCRIPTION
12VDC solenoid operated unloader valve
With inlet sections type
BR-BN-BRS-BRSO BRF
2 Working section * page 20 5TIR108185 5TIR108153 For 1 working section valve
With 2-way compensator 5TIR108232 5TIR108201 For 2 working sections valve
TYPE: DPC130/C10-1S8EZ3TL1-12VDC CODE: 63411H001 5TIR108281 5TIR108249 For 3 working sections valve
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm), 5TIR108328 5TIR108297 For 4 working sections valve
proportional electrohydraulic control with lever 5TIR108376 5TIR108339 For 5 working sections valve
TYPE: DPC130/C22-1S8EZ3TL1.UTUTSTST-12VDC 5TIR108425 5TIR108393 For 6 working sections valve
CODE: 63411H003 5TIR108472 5TIR108440 For 7 working sections valve
DESCRIPTION: As previous, arranged for port valves and L.S. relief 5TIR108520 5TIR108488 For 8 working sections valve
valves 5TIR108568 5TIR108536 For 9 working sections valve
Without compensator 5TIR108616 5TIR108584 For 10 working sections valve
TYPE: DPC130/D10-1S8EZ3TL1-12VDC CODE: 63412H001
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm),
proportional electrohydraulic control with lever
TYPE: DPC130/D20-1S8EZ3TL1.UTUT-12VDC
CODE: 63412H003
DESCRIPTION: As previous, arranged for port valves
TYPE: DPC130/CV10-1S8EZ3TL1-12VDC CODE: 63413H001
DESCRIPTION: With load check valve, double acting spool for
60 l/min (16 US gpm), proportional electrohydraulic control, with lever
TYPE: DPC130/CV22-1S8EZ3TL1.UTUTSTST-12VDC
CODE: 63413H003
DESCRIPTION: With load check valve, double acting spool for
60 l/min (16 US gpm), proportional electrohydraulic control with lever,
arranged for port valves and L.S. relief valves NOTE (*): Codes are referred to BSP thread.
D1WWED02E 11
DPC130 DPC Series
Inlet section parts ordering codes _ _________________________________________________________________
Valve setting (bar)
DPC130 / BR - S200 - DSK -...... DPC130 / BN21 - S220 - ...... DPC130 / BR21 - S220 - ELP - ...... - 12VDC
1 2 1 5 1 2 5 1 2 3 5 6
2 2 2
1
1 1
3
6
DPC130 / BRS21 - S220 - ELP - ...... - 12VDC DPC130 / BRSOG21(SF) - S220 - ELN3 - ...... - 12VDC
1 2 3 5 6 1 2 4 5 6
2 6
3 1
6
1 2
DPC130 / BRF21 - S250 - BSP
1 2 5
Circuit conversion kit
12 D1WWED02E
DPC Series DPC130
___________________________________________________________________
Inlet section parts ordering codes
1 Inlet section kit* page 14 3 Solenoid operated unloading valve page 19

TYPE: DPC130/BR-DSK CODE: 5FIA631350 Needs coil type BER: see chapter 6
DESCRIPTION: With compensator, pressure reducing valve and TYPE CODE DESCRIPTION
selector for open/closed center circuit ELN 0EC08002031 Without emergency override
Open Center circuit ELP 0EC08002033 With push-button emergency override
TYPE: DPC130/BN11 CODE: 5FIA631303 ELT 0EC08002035 With “twist & push” emergency override
DESCRIPTION: With compensator, without pressure reducing valve ELV 0EC08002034 With screw type emergency override
TYPE: DPC130/BR11 CODE: 5FIA631301 LT XTAP510320 Unloading valve blanking plug
DESCRIPTION: With compensator and pressure reducing valve
TYPE: DPC130/BRS11 CODE: 5FIA631361 4 Shut-Off pilot solenoid valve page 16
DESCRIPTION: Copy-Spool type, with compensator and pressure
Needs coil type BT: see chapter 6
reducing valve
TYPE CODE DESCRIPTION
Closed Center circuit
ELN3 0EJ08002035 Without emergency override
TYPE: DPC130/BN21 CODE: 5FIA631302
ELT3 0EJ08002042 With screw emergency override
DESCRIPTION: Without compensator and pressure reducing valve
TYPE: DPC130/BR21 CODE: 5FIA631300
DESCRIPTION: Without compensator, with pressure reducing valve 5 Section threading
TYPE: DPC130/BRSOG21(SF) CODE: 5FIA631374G Specify only if it is different from BSP standard (see page 5).
DESCRIPTION: Shut-Off type, without compensator, with pressure
reducing valve (L.S. joint without filter)
6 Coil
TYPE: DPC130/BRS21 CODE: 5FIA631360
DESCRIPTION: Copy-Spool type, without compensator, with pressure TYPE CODE DESCRIPTION
reducing valve 12VDC 4SLE001200 12VDC coil type BER, ISO4400 connector
TYPE: DPC130/BRF21 CODE: 5FIA630306 (for unloading valve)
DESCRIPTION: Without compensator, with pressure reducing valve 12VDC 4SL3000120 12VDC coil type BT, ISO4400 connector
(for Shut-Off pilot valve)
2 L.S. relief valves page 19 For complete available coils list see page 70.
Standard setting is referred to 10 l/min (2.6 US gpm flow).

7 Circuit conversion kit
TYPE INITIAL CODE DESCRIPTION
LSD S XCAR126215 With blind nut, These kits ara available only for BN and BR sections; not for BRS,
range 40-180 bar (580-2600 psi), BRSO and BRF sections.
std. setting 90 bar (1300 psi) CODE DESCRIPTION
XCAR126213 As previous, 5KIT130300 Kit for circuit conversion from Open Center to Closed
range 180-350 bar (2600-5100 psi), Center
std. setting 180 bar (2600 psi) 5KIT130310 Kit for circuit conversion from Closed Center to Open
LSH H XCAR126216 With locked arrangement, Center
range 40-180 bar (580-2600 psi),
std. setting 90 bar (1300 psi)
XCAR126217 As previous,
range 180-350 bar (2600-5100 psi),
LSZ Z 5CAR126221 With anti-tamper cap,
range 40-180 bar (580-2600 psi),
5CAR126219 As previous,
range 180-350 bar (2600-5100 psi),
ST ST 5KIT126210 Relief valve blanking plug
NOTE (*): Codes are referred to BSP thread.
D1WWED02E 13
DPC130 DPC Series
Inlet section_ _______________________________________________________________________________________________
Dimensions and hydraulic circuit
Example of BR section
21.5
0.85 K
X
V1
31.5
1.24
K W
V2 Y
max.164.4
max. 6.47
LS
130.4
5.13
Z
3.31
84
54.5
2.15
0.39
10
33.5
X 1.32
28 7 115.5
1.10 0.276 4.55
129.5
5.10
max. 213.5
max. 8.41
0.39
10
Wrenches and tightening torque
T
2.76
E = allen wrench 4
70
F = wrench 17 - 24 Nm (17.7 lbft) p

1.42
36
G = wrench 24 - 42 Nm (31 lbft)
2.09
53
K = allen wrench 5 - 24 Nm (17.7 lbft)
X = allen wrench 6 - 24 Nm (17.7 lbft)
Y = allen wrench 10 - 24 Nm (17.7 lbft) LS
0.67
Z = wrench 19 - 24 Nm (17.7 lbft) 36.5 43.5 11

17
1.44 1.71 0.43

W = wrench 34 - 42 Nm (31 lbft)
100 8
NOTE: for relief valve and solenoid valve wrench and 3.94 0.31
torque see page 19.
Auxiliary ports specification

V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi) for
BR-DSK section configuration
hydraulic pilot control valves feeding (P⇒OUT)
V2 = M14x1.5 pilot pressure port for:
- electrohydraulic controls optional feeding (Pmax = 315 bar - K
X
4600 psi) (P⇒IN); needs G1/4 joint, code 5GIU519611
- pressure gauge connection; needs G1/4 joint, code 5GIU620330. V1
W K
V2
DSK valve:
screw for Open Center
Y
unscrew for Closed Center
Pressure reducing valve diagram

33.5
1.32
Reduced pressure vs. Flow

0 0.8 1.6 2.4 3.6 (US gpm) X
40 (psi) A
(bar)
500
Reduced pressure
F
30
400 G
20 300 T
DSK valve Dim. A
p
200 function mm in
1.42
36
10 E
100 Open Center 24.5 0.96
Z
Open Center 32.5 1.28
26.5
1.04
0 0
0 3 6 9 12 15 (l/min)
Flow LS
X
14 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
Example of BN section
21.5
0.85 Y
X
V1 W
31.5
1.24 X V2
max.164.4
max. 6.47
Z
130.4
5.13
LS
3.31
84
54.5
2.15
0.39
10
28 2 7 115.5
1.10 0.079 0.276 4.55
129.5
5.10
0.39
10
V1 = G1/4 pilot pressure port for electrohydraulic
2.76
70
controls feeding (Pmax = 30 bar - 435 psi) (P⇒IN) T

V2 = G1/4 pressure gauge connection p
2.09
53
Y = allen wrench 10 - 24 Nm (17.7 lbft) LS
0.67
Z = wrench 19 - 24 Nm (17.7 lbft)

17
36.5 43.5 11
W = wrench 34 - 42 Nm (31 lbft) 1.44 1.71 0.43
100 8
NOTE: for relief valve wrench and torque see page 19 3.94 0.31
BR11 type BR21 type BR-DSK type BN11 type BN21 type
(in open center)
P T P T P T P T P T
V2 V2 V2 V2 V2
V1 V1 V1 V1 V1
LS LS
LS LS LS
D1WWED02E 15
DPC130 DPC Series
Inlet section_ _______________________________________________________________________________________________
Example of BRSOG21 section

For pressure reducing valve features, see page 14.
T P
Shut-off pilot
solenoid valve
21.5
19.5
0.85
0.77
V1
max. 219
max. 8.62
X
Y
Z 130.4
W 5.13
110.8
4.36
96.7
3.81
M
0.39
1.77
10
45
X
27.5 7 115.5 50.8
1.08 0.28 4.55 2.00
LS
17 70 127
0.67 2.76 5.00
9
0.354
T
p Auxiliary ports specification
M = G1/4 pressure gauge connection
17.5
0.69
X V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi)

for hydraulic pilot control valves feeding (P⇒OUT)
64.8
2.55
K
43.5
V1
1.71

1.10
28

LS X = allen wrench 6 - 24 Nm (17.7 lbft)
2.8
0.110 Y = allen wrench 10 - 24 Nm (17.7 lbft)
2 45.5 45 8 Z = wrench 19 - 24 Nm (17.7 lbft)
0.079 1.79 1.77 0.31 W = wrench 34 - 42 Nm (31 lbft)
100
3.94 NOTE: for relief valve wrench and torque see page 19
Pilot solenoid valves

ELN3 ELT3
Valve Dim. A
G
type mm in
ELN3 65.5 2.58
A
ELT3 88.5 3.48
F Legenda
ELN3: without emergency
3 3
ELT3: screw emergency override
2 2
Wrenches and tightening torques
1 1 F = wrench 24 - 30 Nm (22 lbf)
1 1 G = manual tightening
Features
2 3 2 3 Max. flow. . . . . . . . . . . . . . . . : 3 l/min (0.80 US gpm)
Max. pressure. . . . . . . . . . . . . : 350 bar (5100 psi)
Internal leakage. . . . . . . . . . . : 10 cm3/min @ 210 bar
(0.61 in3/min @ 3050 psi)
For coil features and options see coil BT at page 70.
16 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
Example of BRS section

For pressure reducing valve features, see page 14.
12
H 0.47
X Z
V1 LS
LS
31.5
1.24
K V2 W
max.164.4
Y
max. 6.47
130.4
5.13
I
107.2
4.22
3.31
84
0.39
10
31.5
1.24
28 21.5 H 115.5 X 38 17
1.10 0.85 4.55 1.50 0.67
53 144 70
2.09 5.67 2.76
max. 213.5
max. 8.41
16.5 43.5 11
Auxiliary ports specification 0.65 1.71 0.43
V1 = G1/4 pilot pressure port (Pmax =
0.39
10
30 bar - 435 psi) for hydraulic pilot control
valves feeding (P⇒OUT)
V2 = M14x1.5 pilot pressure port for: T
p
- electrohydraulic controls optional fee-
ding (Pmax = 315 bar - 4600 psi) (P⇒IN);
2.09
53
needs G1/4 joint, code 5GIU519611 LS

- pressure gauge connection; needs G1/4 H K
joint, code 5GIU620330.
7.5 100 8
Wrenches and tightening torque 0.295 3.94 0.315
I = wrench 17 - 24 Nm (17.7 lbft)
H = allen wrench 4 - 9.8 Nm (7.2 lbft)
J = allen wrench 6 BRS11 type BRS21 type
P T P T
Y = allen wrench 10 - 24 Nm (17.7 lbft)
Z = wrench 19 - 24 Nm (17.7 lbft)
W = wrench 34 - 42 Nm (31 lbft) V2 V2
NOTE: for relief valve and solenoid valve wrench and
torque see page 19.
V1 V1
LS
LS
D1WWED02E 17
DPC130 DPC Series
Inlet section_ _______________________________________________________________________________________________
Example of BRF section
Pressure reducing valve
Z P T
M
X
5.83
148
132.5
5.22
1.42
36
Z
LS
1.81
46
1.50
34.5
1.36
38
46.8 24.2 14 17
X
0.39
1.84 0.95
10
0.55 0.67
100 38 LS
3.94 1.50
6 30.5
0.236 1.20
H
LS
1.42
36
1.06
27
64 7.5
2.52 0.295
115.5
4.55
137
5.39
Wrenches and tightening torque Pressure reducing valve features

H = allen wrench 4 - 9.8 Nm (7.2 lbft) Max. inlet pressure. . . . . . : 380 bar (5550 psi)
X = allen wrench 6 - 24 Nm (17.7 lbft) Reduced presure range . . . : from 30 to 45 bar
Z = wrench 19 - 24 Nm (17.7 lbft) (from 435 to 650 psi)
NOTE: for relief valve wrench and torque see page 19. Max. back pressure. . . . . . : 25 bar (363 psi)
Pressure reducing valve diagram

Reduced pressure vs. Inlet pressure
0 1000 2000 3000 4000 5000 (psi)
50
(bar) (psi)
600
Reduced pressure
40
30 450
20 300
10 150
0 0
0 70 140 210 280 350 (bar)
Pressure
18 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
L.S. pressure relief valve
LSH LSD
W Y Pressure vs. flow diagram
B
Y Y (1) = valve range 40-180 bar (580-2600 psi)
X X (2) = valve range 180-350 bar (2600-5000 psi)
0 10 20 30 (US gpm)
J J 400
max. setting(2) (psi)
(bar)
5000
300
LSZ ST medium range setting(2) 4000
Pressure
codice K min. and std. setting(2) 3000
200 max. setting(1)
4COP116420
2000
X std. setting(1)
J 100
min. setting(1) 1000
0 0
J
0 30 60 90 120 150 (l/min)
Flow
Legenda
Valve Dim. B
LSH: with lock arrangement
LSD: with blind nut
type mm in
LSZ: with anti-tamper cap LSD 21.5 0.85
ST: valve blanking plug
LSH 17 0.67
LSZ 34 1.34
X = wrench 13 - 24 Nm (17.7 lbf)
Y = wrench 10 - 9.8 Nm (7.2 lbf)
W = allen wrench 3
J = wrench 7 - 24 Nm (17.7 lbf)
K = allen wrench 5 - 24 Nm (17.7 lbf)
Solenoid operated unloading valve
On BR and BRS section

ELN ELP ELV
G F
1 1 1
2 2 2
1 1 1
2 2 2
ELT
LT
C 1
E
2
Valve Dim. C
type mm in Features
ELN 65.5 2.58 Max. flow. . . . . . . . . . . . . . . . : 40 l/min (10.6 US gpm)
ELP 88.5 3.48 Max. pressure. . . . . . . . . . . . . : 380 bar (5500 psi)
Internal leakage. . . . . . . . . . . : 0.25 cm3/min @ 210 bar
ELV 88.5 3.48
(0.015 in3/min @ 3050 psi)
ELT 91 3.58 For coil features and options see coil BER at page 70.
D1WWED02E 19
DPC130 DPC Series
Working section parts ordering codes (mechanical, hydraulic)_ ____________________________
port A port B port A port B Valve setting (bar)
DPC130/C22-1S 8IM L 1 . U100U320 S250S250-......
1 2 3 4 5 6 7
Lever position: see page 36
1 Working section kit* page 22

6 8 With compensator
TYPE: DPC130/C10 CODE: 5EL6311310
5 DESCRIPTION: Without valves arrangement
DESCRIPTION: As previous with additional upper L.S. port
DESCRIPTION: With port valves arrangement
TYPE: DPC130/C24 CODE: 5EL6311324A
Section C22
3 3 TYPE: DPC130/C21 CODE: 5EL6311321
DESCRIPTION: Arranged for port valves and one L.S. relief valve
4
1 TYPE: DPC130/C22 CODE: 5EL6311322
2 DESCRIPTION: Arranged for port valves and two L.S. relief valves
TYPE: DPC130/F10 CODE: 5EL6314310
DESCRIPTION: For floating circuit, without port valves arrangement
3 TYPE: DPC130/F20 CODE: 5EL6314320.
DESCRIPTION: For floating circuit, with port valves arrangement
TYPE: DPC130/CM23 CODE: 5EL6311325B
DESCRIPTION: For regenerative circuit, arranged for port valves and
one L.S. relief valve
DESCRIZIONE: Arranged for port valves and two L.S. relief with
independent drain: needs dedicated spools (chapter 2A)
Without compensator
DPC130/C26-1NA 8IML1.U100U320S250S250-.... TYPE: DPC130/D10 CODE: 5EL6312310
DESCRIPTION: Without valves arrangement
1 2A TYPE: DPC130/D20 CODE: 5EL6312320
TYPE: DPC130/D21 CODE: 5EL6312321
TYPE: DPC130/G20 CODE: 5EL6315320
TYPE: DPC130/DM23 CODE: 5EL6312350
Without compensator, with check valve
TYPE: DPC130/CV10 CODE: 5EL6311310B
Section C26 DESCRIPTION: Without valves arrangement
TYPE: DPC130/CV13 CODE: 5EL6311313A
1 TYPE: DPC130/CV21 CODE: 5EL6311321D
2A DESCRIPTION: Arranged for port valves and one L.S. relief valve
DESCRIPTION: Arranged for port valves and two L.S. relief valves
TYPE: DPC130/FV20 CODE: 5EL6314320B
TYPE: DPC130/CVM23 CODE: 5EL6311325A
NOTE (*): Codes are referred to BSP thread. one L.S. relief valve
20 D1WWED02E
DPC Series DPC130
_____________________________
Working section parts ordering codes (mechanical, hydraulic)
2 Spool page 25 3 "A" side spool control kit page 27

PFlow is referred to 7 bar (102 psi) stand-by (margin pressure) TYPE CODE DESCRIPTION
TYPE CODE DESCRIPTION Mechanical positioners
Double acting with A and B closed in neutral position 7FT# 5V07130000 With friction and center pos. feeling
1C 3CU4010005 5 l/min (1.3 US gpm) flow 8 5V08130000 3 position, spring return to neutral position
1D 3CU4010010 10 l/min (2.6 US gpm) flow 13 5V13130000 For floating circuit (spool type 5), 4 pos.,
1V 3CU4010025 25 l/min (6.6 US gpm) flow detent in 4th position, with spring return to
1Q 3CU4010040 40 l/min (10.6 US gpm) flow neutral position
1S 3CU4010060 60 l/min (15.9 US gpm) flow NOTE (#): Control that requires modification to the standard spool:
1N 3CU4010080 80 l/min (21.1 US gpm) flow for spool replacement see page 29.
1PN 3CU4010103 100 l/min (26.4 US gpm) flow Proportional hydraulic controls
Double acting with A and B to tank in neutral position 8IM 5V08130800* Range 5-15 bar (73-218 psi)
2C 3CU4024005 5 l/min (1.3 US gpm) flow
2D 3CU4024010 10 l/min (2.6 US gpm) flow 4 "B" side spool control kit page 36
2V 3CU4024025 25 l/min (6.6 US gpm) flow
2Q 3CU4024040 40 l/min (10.6 US gpm) flow
L 5LEV130712 Aluminium lever box
2S 3CU4024060 60 l/min (15.9 US gpm) flow
LN 5LEV130701 As previous, without lever
2N 3CU4024080 80 l/min (21.1 US gpm) flow
LZ 5LEV130731 As type L, with anti-tamper screw caps
2P 3CU4024100 100 l/min (26.4 US gpm) flow
LG 5LEV130806 Cast iron lever box
Double acting with A and B partially to tank in neutral position
2HC 3CU4025006 5 l/min (1.3 US gpm) flow
2HD 3CU4025011 10 l/min (2.6 US gpm) flow 5 Port valves page 37
2HV 3CU4025034 25 l/min (6.6 US gpm) flow TYPE CODE DESCRIPTION
2HQ 3CU4025047 40 l/min (10.6 US gpm) flow UT XTAP522441 Valve blanking plug
2HS 3CU4025061 60 l/min (15.9 US gpm) flow C 5KIT410000 Anticavitation valve
2HN 3CU4025081 80 l/min (21.1 US gpm) flow Fixed setting antishock and anticavitation valves: setting is
2HP 3CU4025102 100 l/min (26.4 US gpm) flow referred to 10 l/min (2.6 US gpm)
Single acting on A, B plugged: needs G1/2 plug TYPE: U 100 CODE: 5KIT330 100
3Q 3CU4031040 40 l/min (10.6 US gpm) flow setting (bar) setting (bar)
3S 3CU4031060 60 l/min (15.9 US gpm) flow SETTING:
3N 3CU4031080 80 l/min (21.1 US gpm) flow 50 bar (725 psi) 63 bar (914 psi) 80 bar (1150 psi)
3PN 3CU4031100 100 l/min (26.4 US gpm) flow 100 bar (1450 psi) 110 bar (1590 psi) 125 bar (1800 psi)
Double acting with A and B closed in neutral position, 4 positions, 140 bar (2050 psi) 150 bar (2150 psi) 160 bar (2300 psi)
floating in 4th pos. with spool out: needs sections type F, G or FV, 175 bar (2550 psi) 190 bar (2750 psi) 200 bar (2900 psi)
positioner and controls type 13 210 bar (3050 psi) 230 bar (3350 psi) 240 bar (3500 psi)
5Q 3CU4041040 40 l/min (10.6 US gpm) flow 250 bar (3600 psi) 260 bar (3750 psi) 270 bar (3900 psi)
5S 3CU4041060 60 l/min (15.9 US gpm) flow 280 bar (4050 psi) 290 bar (4200 psi) 300 bar (4350 psi)
5N 3CU4041080 80 l/min (21.1 US gpm) flow 310 bar (4500 psi) 320 bar (4650 psi) 340 bar (4950 psi)
Double acting with A and B closed in neutral position, 3 positions, 360 bar (5200 psi) 400 bar (5800 psi) 420 bar (6100 psi)
regenerative in 3rd pos. with spool out: needs sections type CM, DM
or CVM, dedicated controls type 8 with reduced stroke
6 L.S. port relief valves page 37
8F 3CU4033070 50-70 l/min flow (port A-port B)
(13.2-18.5 US gpm) Standard setting is referred to 10 l/min (2.6 US gpm) flow.
Double acting with A and B closed in neutral position, 4 positions, TYPE ID CODE DESCRIPTION
regenerative in 4th pos. with spool out: needs sections type CM, DM LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600
or CVM, dedicated controls type 13 psi), standard setting 90 bar (1300 psi)
8Y 3CU4044070 70 l/min (18.5 US gpm) flow XCAR126213 As prev., range 180-350 bar (2600-5100 psi),
standard setting 180 bar (2600 psi)
LSH H XCAR126216 With locked arrangement, range 40-180 bar
2A Spool page 25
(580-2600 psi), std setting 90 bar (1300 psi)
Only for working section type C26 XCAR126217 As prev., range 180-350 bar (2600-5100 psi),
Flow is referred to 7 bar (102 psi) stand-by (margin pressure) standard setting 180 bar (2600 psi)
TYPE CODE DESCRIPTION LSZ Z 5CAR126221 With anti-tamper cap, range 40-180 bar
Double acting with A and B closed in neutral position (580-2600 psi), std setting 90 bar (1300 psi)
1V 3CU4010025A 25 l/min (6.6 US gpm) flow 5CAR126219 As prev., range 180-350 bar (2600-5100 psi),
1Q 3CU4010040A 40 l/min (10.6 US gpm) flow standard setting 180 bar (2600 psi)
1N 3CU4010080A 80 l/min (21.1 US gpm) flow ST ST 5KIT126210 Relief valve blanking plug
Double acting with A and B partially to tank in neutral position
2HV 3CU4025034A 25 l/min (6.6 US gpm) flow
7 Section threading
2HQ 3CU4025047A 40 l/min (10.6 US gpm) flow
2HN 3CU4025081A 80 l/min (21.1 US gpm) flow Specify only if it is different from BSP standard (see page 5).
8 Plug for single acting spool*

CODE DESCRIPTION
3XTAP727180 G1/2 plug
D1WWED02E 21
DPC130 DPC Series
Working section parts ordering codes (electrohydraulic)_____________________________________
Valve setting (bar) port A port B port A port B
DPC130/C22-1N 8EZ3T L 1 . U100U320 S250S250-......-12VDC DPC130/D10-1N 8EZ3TSPSDL1 -.....-12VDC
1 2 3 4 5 6 7 3 1 2 3
Lever position: see page 36
1 Working section kit* page 22

5 With compensator
Section C22
3 DESCRIPTION: With port valves arrangement
3 TYPE: DPC130/C24 CODE: 5EL6311324A
4 TYPE: DPC130/C21 CODE: 5EL6311321.
1 2 TYPE: DPC130/C23 CODE: 5EL6311323.
TYPE: DPC130/C22 CODE: 5EL6311322.
DESCRIPTION: Arranged for port valves and two L.S. relief valves
3
TYPE: DPC130/F10 CODE: 5EL6314310
DESCRIPTION: For floating circuit, without port valves arrangement
TYPE: DPC130/F20 CODE: 5EL6314320.
Section D10 DESCRIPTION: For floating circuit, with port valves arrangement
3 TYPE: DPC130/CM23 CODE: 5EL6311325B
3 DESCRIPTION: For regenerative circuit, arranged for port valves and
4 TYPE: DPC130/C26 CODE: 5EL6323000
DESCRIZIONE: Arranged for port valves and two L.S. relief with
1 2 independent drain: needs dedicated spools (chapter 2A)
Without compensator
3 TYPE: DPC130/D20 CODE: 5EL6312320
TYPE: DPC130/G20 CODE: 5EL6315320
DPC130/C26-1NA 8EZ3TL1.U100U320S250S250-...-12VDC
TYPE: DPC130/DM23 CODE: 5EL6312350
1 2A
Section C26 DESCRIPTION: With port valves arrangement
TYPE: DPC130/CV21 CODE: 5EL6311321D
1
2A DESCRIPTION: Arranged for port valves and two L.S. relief valves
TYPE: DPC130/FV20 CODE: 5EL6314320B
TYPE: DPC130/CVM23 CODE: 5EL6311325A
22 D1WWED02E
DPC Series DPC130
_____________________________________
Working section parts ordering codes (electrohydraulic)
2 Spool page 25 3 Electrohydraulic controls page 31

Flow is referred to 7 bar (102 psi) stand-by (margin pressure) TYPE CODE DESCRIPTION
TYPE CODE DESCRIPTION Standard types
Double acting with A and B closed in neutral position 8EZ3-12VDC 5V08130780 With ISO4400 connector
1C 3CU4010005 5 l/min (1.3 US gpm) flow 8EZ3-24VDC 5V08130781 With ISO4400 conNector
1D 3CU4010010 10 l/min (2.6 US gpm) flow 8EZ4-12VDC 5V08130880 With flying leads
1V 3CU4010025 25 l/min (6.6 US gpm) flow 8EZ4-24VDC 5V08130881 With flying leads
1Q 3CU4010040 40 l/min (10.6 US gpm) flow 8EZ4D-12VDC 5V08130886 With Deutsch connector
1S 3CU4010060 60 l/min (15.9 US gpm) flow 8EZ4D-24VDC 5V08130887 With Deutsch connector
1N 3CU4010080 80 l/min (21.1 US gpm) flow 8EZ3T-12VDC 5V08130874 With AMP integrated conn.
1PN 3CU4010103 100 l/min (26.4 US gpm) flow 8EZ3T-24VDC 5V08130875 With AMP integrated conn.
Double acting with A and B to tank in neutral position 8EZ3T4-12VDC 5V08130872 With Deutsch integrated conn.
2C 3CU4024005 5 l/min (1.3 US gpm) flow 8EZ3T4-24VDC 5V08130873 With Deutsch integrated conn.
2D 3CU4024010 10 l/min (2.6 US gpm) flow With digital spool position sensor#
2V 3CU4024025 25 l/min (6.6 US gpm) flow 8EZ3TSPSD-12VDC 5V0813087A With AMP integrated connector
2Q 3CU4024040 40 l/min (10.6 US gpm) flow 8EZ3TSPSD-24VDC 5V08130876 With AMP integrated connector
2S 3CU4024060 60 l/min (15.9 US gpm) flow 8EZ3T4SPSD-12VDC 5V0813087C With Deutsch integrated conn.
2N 3CU4024080 80 l/min (21.1 US gpm) flow 8EZ3T4SPSD-24VDC 5V0813087D With Deutsch integrated conn.
2P 3CU4024100 100 l/min (26.4 US gpm) flow With analog spool positions sensor#
Double acting with A and B partially to tank in neutral position 8EZ3TSPSL-12VDC 5V0813087B With AMP integrated connector
2HC 3CU4025006 5 l/min (1.3 US gpm) flow 8EZ3TSPSL-24VDC 5V08130878 With AMP integrated connector
2HD 3CU4025011 10 l/min (2.6 US gpm) flow 8EZ3T4SPSL-12VDC 5V0813087E With Deutsch integrated conn.
2HV 3CU4025034 25 l/min (6.6 US gpm) flow 8EZ3T4SPSL-24VDC 5V0813087F With Deutsch integrated conn.
2HQ 3CU4025047 40 l/min (10.6 US gpm) flow For floating circuit: need spool type 5
2HS 3CU4025061 60 l/min (15.9 US gpm) flow 13EZ3-12VDC 5V13130780 With ISO4400 connector
2HN 3CU4025080 80 l/min (21.1 US gpm) flow 13EZ3-24VDC 5V13130781 With ISO4400 connector
2HP 3CU4025100 100 l/min (26.4 US gpm) flow For 3 positions regenerative circuit: need spool type 8F
Single acting on A, B plugged: needs G1/2 plug 8EZ3CR-12VDC 5V08130798 With ISO4400 connector
3Q 3CU4031040 40 l/min (10.6 US gpm) flow 8EZ3CR-24VDC 5V08130799 With ISO4400 connector
3S 3CU4031060 60 l/min (15.9 US gpm) flow For 4 positions regenerative circuit: need spool type 8Y
3N 3CU4031080 80 l/min (21.1 US gpm) flow 13EZ3-12VDC 5V13130783 With ISO4400 connector
3PN 3CU4031100 100 l/min (26.4 US gpm) flow 13EZ3-24VDC 5V13130784 With ISO4400 connector
Double acting with A and B closed in neutral position, 4 positions, 13EZ3T-12VDC 5V13130786 With AMP integrated connector
floating in 4th pos. with spool out: needs sections type F, G or FV, 13EZ3T-24VDC 5V13130785 With AMP integrated connector
positioner and controls type 13 NOTE (#): Controls that require modification to the standard spool:
5Q 3CU4041040 40 l/min (10.6 US gpm) flow for spool replacement see page 35.
5S 3CU4041060 60 l/min (15.9 US gpm) flow
5N 3CU4041080 80 l/min (21.1 US gpm) flow 4 "B" side spool control kit page 36
Double acting with A and B closed in neutral position, 3 positions,
regenerative in 3rd pos. with spool out: needs sections type CM, DM
L 5LEV130712 Aluminium lever box
or CVM, dedicated controls type 8 with reduced stroke
For complete controls list see previous pages
8F 3CU4033070 50-70 l/min flow (port A-port B)
(13.2-18.5 US gpm)
Double acting with A and B closed in neutral position, 4 positions,
5 Port valves page 37
regenerative in 4th pos. with spool out: needs sections type CM, DM TYPE CODE DESCRIPTION
or CVM, dedicated controls type 13 U100 5KIT330100 Setting 100 bar (1450 psi)
8Y 3CU4044070 70 l/min (18.5 US gpm) flow For complete valves list see previous pages
2A Spool page 25 6 L.S. port relief valves page 37

Only for working section type C26 Standard setting is referred to 10 l/min (2.6 US gpm) flow.
Flow is referred to 7 bar (102 psi) stand-by (margin pressure) TYPE ID CODE DESCRIPTION
TYPE CODE DESCRIPTION LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600 psi),
Double acting with A and B closed in neutral position standard setting 90 bar (1300 psi)
1V 3CU4010025A 25 l/min (6.6 US gpm) flow For complete valves list see previous pages
1Q 3CU4010040A 40 l/min (10.6 US gpm) flow
1N 3CU4010080A 80 l/min (21.1 US gpm) flow 7 Section threading
Double acting with A and B partially to tank in neutral position Specify only if it is different from BSP standard (see page 5).
2HV 3CU4025034A 25 l/min (6.6 US gpm) flow
2HQ 3CU4025047A 40 l/min (10.6 US gpm) flow
2HN 3CU4025081A 80 l/min (21.1 US gpm) flow 8 Plug for single acting spool*
CODE DESCRIPTION
3XTAP727180 G1/2 plug
D1WWED02E 23
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
With compensator
Type C10 Type C22

without port valves with arrangement for port valves and L.S. relief valve
LSAB
0.43
11
69.5
Z X 2.74
130.4
5.13
L.S. valve X
71.5
86 15
2.81
on port B 3.39 0.59 Port B valve

0.39
39.5
10
1.56
0.47
12
0.157
1.413
1.42
35.9
33 41.5
36
4
1.30 1.63 lever side A
B
0.476
L.S. valve
12.1
Port A
0.63 0.63
1.89
16
48
on port A
valve 79 18.5
A
16
3.11 0.73
8 Type C26
40 116
0.315 with arrangement for port valves and L.S. relief valve
1.57 4.57
with independent drain
20.5
Type C13 X 0.81
without port valves with upper L.S port LSB
0.43 1.02
26
LSA
11
Z 69.5
X
2.74
5.31
135
Z
X 12
0.47
B
11.8
0.46
LSAB'
A
0.157
Port B valve
4
L.S. valve on port A

X
8 B
0.315
A
X = allen wrench 6 - 24 Nm (17.7 lbft) Port A L.S. valve
Z = wrench 19 - 50 Nm (36.9 lbft) valve on port B
24 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
With compensator
Type C10 Type C13 Type C22 Type C26

without arrangement As type C10 with with arrangement for port As type C22, L.S. relief valve
for port valves upper L.S. port valves and L.S. relief valve with independent drain
B A LSAB’ B A B A B A
LSAB LSAB LSAB LSA LSB
Type C24 Type C21 Type C23

Type C20 As type C20 with with arrangement for port As type C21 with
with port valves arrangement upper L.S. port valves and one L.S. relief valve upper L.S. port
B A LSAB’ B A B A LSAB’ B A
LSAB LSAB LSAB LSAB
D1WWED02E 25
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
With compensator
Type F10 Type F20 Type CM23

for floating circuit without for floating circuit with for regenerative circuit with arrangement
port valves arrangement port valves arrangement for port valves and one L.S. relief valve
B A B A B A
LSAB LSAB LSAB
Without compensator Without compensator, with check valve

Dimensions are the same of types with compensator. Dimensions are the same of types with compensator.
See pages 20-22 for section configuration list, and pages 25- See pages 20-22 for section configuration list, and pages 25-
26 for circuit representation. 26 for circuit representation.
Type D10 Type CV10

without port valves arrangement without port valves arrangement
B A B A
3.5
0.138
LSAB LSAB
26 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Spools
Spool type 1 Spool type 2 Spool type 2H

A, B closed in neutral position A, B open to tank in neutral pos. A, B partially to tank in neutral pos.
1 0 2 1 0 2 1 0 2
P P P
T T T
A B A B A B
Spool stroke Spool stroke Spool stroke

position 1: + 7 mm (+ 0.28 in) position 1: + 7 mm (+ 0.28 in) position 1: + 7 mm (+ 0.28 in)
position 2: - 7 mm (- 0.28 in) position 2: - 7 mm (- 0.28 in) position 2: - 7 mm (- 0.28 in)
Spool type 3 Spool type 5 Spool type 8F

single acting on A floating in 4th position (pos.3) regenerative in 2nd position (pos.1)
1 0 2 3 1 0 2 1 0 2
P P P
T T T
A B A B A B

position 3: + 12 mm (+ 0.47 in)
Spool type 8Y
regenerative in 4th position (pos.3)
3 1 0 2
P
A B
Spool stroke
position 1: + 4.5 mm (+ 0.18 in)
position 2: - 4.2 mm (- 0.17 in)
position 3: + 7.8 mm (+ 0.31 in)
D1WWED02E 27
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
Spools
Following curves are detected with standard spools, connecting P⇒A⇒B⇒T and P⇒B⇒A⇒T ports without flow multiplication.
Customized spools with backpressure or flow multiplication may require different force, pressure and pilot current for
operation.
Metering curves
Compensated working section - 3 positions spools
Qin = 150 l/min (39.6 US gpm)
217.5 200 160 120 80 72.5 0 72.5 80 120 160 200 217.5
(psi)
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
150
(US gpm)
(l/min)
120 32
P P
N N
24
Port flow
90
S S
60 16
Q Q
V V
30 8
D D
C C
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Spool stroke position 1
Pilot pressure
(bar)
With 8IM
15.0 12.5 10.0 7.5 5.0 0 5.0 7.5 10.0 12.5 15.0
control kit
Current (mA@12VDC)
1000 900 800 700 600 500 0 500 600 700 800 900 1000
With 8EZ3 and
8EZ3T control kit (mA@24VDC)
500 450 400 350 300 250 0 250 300 350 400 450 500
Non-compensated working section

Spool flow vs. Stand-by pressure
(margin pressure)
0 80 160 240 320 (psi)
160
102 P 40
(l/min) N
(US gpm)
S Spool nominal flow @ 7 bar (102 psi)
120
30 stand-by (margin pressure)
Port flow
Q C = 5 l/min (1.3 US gpm)

80 D = 10 l/min (2.6 US gpm)
20
V V = 25 l/min (6.6 US gpm)
Q = 40 l/min (10.6 US gpm)
40 D 10 S = 60 l/min (15.9 US gpm)
C N = 80 l/min (21.1 US gpm)
P = 100 l/min (26.4 US gpm)
0 0
0 5 10 15 20 25 (bar)
7 Pressure
28 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
"A" side spool control kit
With friction and center position feeling: type 7FT

17.5
0.69
Y Z
X
1 0 2
71.5
2.81
113.5 Features
4.47
Friction load adjusting. . . . . : 20-150 N (4.5-34 lbf)
Friction load std. setting . . . : 100 N (22.5 lbf)
Center tap (more than load).: 100 N (22.5 lbf)
NOTE: spool replacement Wrenches and tightening torque

spool
The spool for this control must be selec- X = allen wrench 5 - 9.8 Nm (7.2 lbf)
ted from the list on page 21. Y = wrench 24 - 42 Nm (31 lbf)
For spool assembling you must remove Z = wrench 13 - 24 Nm (17.7 lbf)
the screw (wrench 13) on the back of W = allen wrench 6
screw spool and clean the cavity from Loctite®
residue; the screw must be trashed.
With spring return to neutral position: type 8

It’s supplied with standard spring type A(see force-stroke diagram); available with stronger spring type C (8MC code:
5V08230000).
16 Force vs. Stroke diagram
0.63
0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 (in)
(N) 0 0.05 0.1 0.15 0.2 0.25 (in)

150
X 32
(lbf)
120
1 0 2 Spring type C 24
90
Force
16
71.5
2.81
60
Spring type A
8
30
0 0
0 1 2 3 4 5 6 7 pos.1 (mm)
X = allen wrench 5 - 9.8 Nm (7.2 lbf) 0 -1 -2 -3 -4 -5 -6 -7 pos.2 (mm)
Stroke
Spring type A = from 35.6 N (8 lbf) to 81.8 N (18.4 lbf)

Spring type C = from 82.3 N (18.5 lbf) to 116.8 N (26.3 lbf)
D1WWED02E 29
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
With detent in 4th position (pos.3), for floating circuit: type 13

Need working sections type F, G or FV and floating circuit spools type 5.
10.5
0.41
3 1 0 2
71.5
2.81
Features
Y Detent force (±10%). . . . . . : 310 N (70 lbf)
Release force (±10%). . . . . : 110 N (24.7 lbf)
45.5
1.79 Wrenches and tightening torque
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = wrench 13 - 24 Nm ( 17.7 lbf)
Proportional hydraulic controls

31
1.22
G1/4
nr.2 threads VB
1.06
VA VB
27
VA
1 0 2
X
71.5
71.5
2.81
2.81
Features
Max. pressure. . . . . . . . . . . . . : 50 bar (725 psi)
24
48 X = allen wrench 5 - 9.8 Nm (7.2 lbf)
1.89 Y = wrench 13 - 24 Nm ( 17.7 lbf)
Suggested pressure
Stroke vs. Pressure diagram control curve: type 020
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in) 0 0.05 0.10 0.15 0.20 0.25 0.3 (in)
20 (psi) 40 (psi)
35 bar (508 psi)
(bar) 250 (bar) 500
15 30
Pilot pressure
200 400
Pressure
10 150 20 300
(0.30 in)
spool 15.3 bar (220 psi)

dead band 100 200
5
7.25 mm
10 4.3 bar
(0.29 in)
7.6 mm
50 (63 psi) 100

0.85 mm
0 0 (0.033 in)
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm) 0 2 4 6 8 (mm)
position 2 Stroke position 1 Pusher stroke
30 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Electrohydraulic controls
Following specifications are measured with:

• mineral oil of 46 mm2/s (46 cSt) viscosity at 40°C (104°F) temperature,
• 20°C (60°F) environmental temperature,
• standard spools, connecting P⇒A⇒B⇒T ports without flow multiplication,
• 12 VDC and 24 VDC nominal voltage with tolerance ± 10%.
Standard spool Regenerative spool Floating spool

Specifications
control type control type control type
8EZ3 8EZ3T 8EZ3CR (8Y)13EZ3 13EZ3
Electric specifications
12 VDC 6.7 Ω 4.7 Ω 6.7 Ω 6.7 Ω 6.7 Ω

Coil impedance
24 VDC 24.7 Ω 20.8 Ω 24.7 Ω 24.7 Ω 24.7 Ω
Max. operating 12 VDC 1.79 A 1.50 A 1.79 A 1.79 A 1.79 A

current 24 VDC 0.97 A 0.75 A 0.97 A 0.97 A 0.97 A
No load current consumption - - - - -
Hysteresis max. (1)

external drain 10% 10% 10% 10% 10%
from 0 ⇒ 100% and
Time response from 100% ⇒ 0 < 150 ms < 150 ms < 150 ms < 150 ms < 150 ms
of stroke
Min. flow control 12 VDC 500 mA 500 mA 560 mA 560 mA 220 mA

signal 24 VDC 250 mA 250 mA 280 mA 280 mA 110 mA
Max. flow 12 VDC 1000 mA 1000 mA 800 mA 800 mA 560 mA

control signal 24 VDC 500 mA 500 mA 400 mA 400 mA 280 mA
Min. Regenerative 12 VDC - - - 1100 mA -

flow control signal 24 VDC - - - 550 mA -
Max. Floating/ 12 VDC - - - 1300 mA 900 mA
Regenerative flow
control signal 24 VDC - - - 650 mA 450 mA
Dither frequency high frequency 150 Hz (200 mA) 100 Hz (200 mA) 150 Hz (200 mA)
Insertion 100% 100%

Class F Class H
Coil insulance Class F (155°C - 311°F)
(155°C - 311°F) (180°C - 356°F)
ISO4400
AMP JPT
Connector type Flying leads ISO4400
Deutsch DT
Deutsch DTM
IP65 (type
IP65 (type JPT)
Weather protection (connector) ISO4400) IP65
IP69K (type DT)
IP69K (type DTM)
Hydraulic specifications
Max. pressure 50 bar (725 psi) 50 bar (725 psi)
Max. back pressure on drain 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) For the calculation rules see "Appendix A" on page 74.
Listed electrohydraulic controls need CED100X or CED400X electronic control unit; for information contact Sales Department.
D1WWED02E 31
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
Spool stroke vs. pilot current diagrams
Types 8EZ3 - 8EZ4 - 8EZ4D - 8EZ3T

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
1400 700
(mA@12VDC) spool (mA@24VDC)
dead band
1050 525
1000 /500 mA
Current
700 350
500 /250 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Stroke position 1
Types 13EZ3 - 13EZ4: for floating circuit

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 (in)
1400 700
(mA@12VDC) (mA@24VDC)
1050 525
spool C
dead band
Current
700 350 Ref. Current (mA) Stroke

E B 12VDC 24VDC mm (in)
A 220 110 2 (0.079)
350 175 B 560 280 7 (0.276)
C 900 450 12 (0.472)
D A D 220 110 -2 (-0.079)
0 0 E 560 280 -7 (-0.276)
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 (mm)
position 2 Stroke position 1 position 3
Type 8EZ3CR: for regenerative circuit

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
1400 700
dead band
1050 525
Current
800 / 400 mA
700 350
560 /280 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
Type (8Y)13EZ3: for regenerative circuit

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
1400 700
D
dead band C
1050 525
B
Current
Ref. Current (mA) Stroke

700 F 350 12VDC 24VDC mm (in)
A A 560 280 2 (0.079)
B 850 425 4.5 (0.177)
350 E 175 C 1100 550 6 (0.236)
D 1300 650 7.8 (0.307)
E 440 210 -1 (-0.039)
0 0 F 800 405 -4.2 (-0.165)
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 2 Stroke position 1 position 3
32 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Electrohydraulic controls: spool position sensor

The sensor can be ordered exclusively through the electrohydraulic controls; see page 23 for available control list.
SPSL sensor
The SPSL position sensor converts the spool movements into a voltage linear signal..
Working conditions SPSL sensor output signal

(V) -0.25 -0.20 -0.15 -0.10 -0.05 0 0.05 0.10 0.15 0.20 0.25 (in)
Voltage supply 5 VDC 5
Current absorption < 10 mA (no load)
4
Output voltage
Mechanical life 3x106 operation tolerance
Connector type DT04-4P Deutsch 3
Weather protection IP67 / IP69K 2

from -40°C to 105°C
Working temperature 1
(from -40°F to 221°F)
Working pressure 350 bar (5100 psi) 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
Max. electrical stroke ±10 mm (±0.39 in)
Spool stroke
Max. mechanical stroke ±10 mm (±0.39 in)
Output signal range from 0.5 to 4.5 V
Connector
linearity ± 5%
Deutsch DT04-4P 3 4
spool in neutral 2.5 ± 0.2 V
Pin Function
max. current 1 mA 1 + 5V
EMC compatibility ISO 13766 / ISO 14982 2 not connected
3 GND 2 1
Mechanical vibrations, shock, bumps IEC 68-2-6,-27,-29
4 signal OUT
Mating connector Deutsch DT06-4S, code 5CON140072
SPSD sensor
The SPSD position sensor converts the spool movements into an electric digital signal.
SPSD sensor output signal

Working conditions
(%) -0.25 -0.20 -0.15 -0.10 -0.05 0 0.05 0.10 0.15 0.20 0.25 (in)
Voltage supply from 9 to 32 VDC 100
80
Battery voltage
operation tolerance
operation tolerance
Mechanical life 3x106


(from -40°F to 221°F)
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
Spool stroke
Output signal type PNP
max. current 6 mA Connector
Deutsch DT04-4P 3 4
EMC compatibility ISO 13766 / ISO 14982
Pin Function
1 Out A
2 GND
3 VB + 2 1
4 Out B
D1WWED02E 33
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
Proportional controls, types 8EZ - 13EZ

Control Types
1 : With ISO4400 connector - mating connector code: 2X1001030
2 : With flying leads
3 : With Deutsch DTM04 connector - mating connector Deutsch DTM06 code: 5CON140025
844 800
33.23 31.50
3 2 1 Y
Types
8EZ3 - 8EZ4
8EZ4D - 8EZ3CR
coil 2
1 0 2
174.5
174.5
6.87
X
169.5
6.87
coil 1
6.67
Types
13EZ3 - 13EZ4
71.5
2.81
(8Y)13EZ3 coil 2
coil 1
3 1 0 2
Wrenches and tightening torque B

Y = allen wrench 4 - 6.6 Nm (4.9 lbf) A
58
2.28
ISO4400 connector Deutsch DTM04 connector
4 1
3
2 1 3 2
GND
Magnet must be assembled

Connectors with this side (printed side)
Wire colour Function
pin facing the section side
without O-ring seating
1 blue common (-)
2 red Coil 2 - Port B
3 green Coil 1 - Port A
4 - Plugged
34 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Control Types
1 : With AMP JPT connector - mating connector AMP JPT, code: 5CON003
2 : With Deutsch DT04 connector - mating connector Deutsch DT06-2S code: 5CON140031
Proportional control types 8EZ3T - 13EZ3T Proportional control types 8EZ3TSPSD -

8EZ3TSPSL
For sensor specification and features see page 33
Types Types 8EZ3TSPSD - 8EZ3T4SPSD

8EZ3T - 8EZ34T CANbus interface
EVB
EVA
1 0 2 EVA
1 0 2
EVB
#
G
Types Types 8EZ3TSPSL - 8EZ3T4SPSL

13EZ3T EVB
Analog input
EVA
3 1 0 2 EVA
1 0 2
EVB
U
G
2 2
1 1
Z
Z
EVA
port A
EVB
port B
EVA
port A
EVB
port B
K J
181.5
7.15
X
170.5
6.71
71.5
71.5
2.81
2.81
B B
A A
70 69.5
2.76 2.74
122
4.80
Wrenches and tightening torque NOTE: spool replacement

spool
X = allen wrench 5 - 9.8 Nm (7.2 lbf) The spool for this control must be selec-
Z = allen wrench 3 - 5 Nm (3.7 lbf) ted from the list on page 21.
J = wrench 17 - 9.8 Nm (7.2 lbf) For spool assembling you must remove
K = allen wrench 4 - 9.8 Nm (7.2 lbf) the screw (wrench 13) on the back of
screw spool and clean the cavity from Loctite®
residue; the screw must be trashed.
D1WWED02E 35
DPC130 DPC Series
Working section_ __________________________________________________________________________________________
"B" side spool control kit
Aluminium lever box; type L Aluminium lever box, without lever; type LN
3 1 0 2 3 1 0 2
21
42 45° 6 0
°3
1.65 0'
X X
16
30
°3
°
0'
1
3
Dimensions are the
same of type L
71.5
2.81
1.85
1.55
47
39
W Z Y Z Y
87
3.43
B
B
0.83
21
R
M8
15° 0
30
°
1
30
°
Lever assembly position Wrenches and tightening torque

2 X = allen wrench 5 - 9.8 Nm (7.2 lbf)
See page 20 for specification
Y = allen wrench 3
in working section description
30°
Z = wrench 10 - 9.8 Nm (7.2 lbf)

W= allen wrench 4 - 6.6 Nm (4.9 lbf)
3
R = wrench 8
°
30
Alum. lever box, with anti-tamper cap; type LZ Cast iron lever box; type LG
3 1 0 2 3 1 0 2
99.5
3.92
Other dimensions and Dimensions and lever

lever positions are the positions are the same
same of type L of type L
W Anti-tamper cap W Z Y
X code: 4COP116420 X
B B
36 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Port valves
D
Type U Type C Type UT

antishock valve anticavitation valve valve blanking plug
5.55 X X X
141

X = wrench 13 - 24 Nm (17.7 lbf)
Type U, setting example Types U-C, pressure drop

B (10 l/min - 2.6 Us gpm) (in anticavitation)
1.413
0 5 10 15 20 25 (US gpm)
35.9
0 5 10 15 20 25 (US gpm)
A 400 40 (psi)
340 bar (4950 psi) (psi)
(bar) (bar)
5000 500
79 18.5 (3900 psi)
0.476
300 30
12.1
270 bar
3.11 0.73 4000 400
Pressure
Pressure
210 bar (3050 psi)
200 3000 20 300
140 bar (2050 psi) eC
Valve Dim. D 2000 Typ
200
80 bar (1150 psi)
type mm in 100 10 U
25 bar (360 psi) 1000 Type 100
U 10.5 0.41
0 0 0 0
C 10.5 0.41 0 20 40 60 80 100 (l/min) 0 20 40 60 80 100 (l/min)
UT 7.5 0.30 Flow Flow
L.S. port relief valves
LSH LSD LSZ ST

E
W cap part K
Y
Y Y 4COP116420
X X X J
J J
5.55
141
Legenda Pressure vs. flow diagram

LSH: with lock arrangement (1) = valve range 40-180 bar (580-2600 psi)
B (2) = valve range 180-350 bar (2600-5000 psi)
LSD: with blind nut
0.47
12
1.42
LSZ: with anti-tamper cap 0 5 10 15 20 25 (US gpm)

36
A 400 (psi)
ST: valve blanking plug (bar) max. setting(2)
5000
86 15
300
3.39 0.59 X = wrench 13 - 24 Nm (17.7 lbf) medium range setting(2) 4000
Y = wrench 10 - 9.8 Nm (7.2 lbf)
Pressure
200 max. setting(1) min. and std. setting(2) 3000

W = allen wrench 3
Valve Dim. E J = wrench 7 - 24 Nm (17.7 lbf) 2000
type mm in K = allen wrench 5 - 24 Nm (17.7 lbf) 100
std. setting(1)
1000
LSD 21.5 0.85 min. setting(1)
LSH 17 0.67 0 0
0 20 40 60 80 100 (l/min)
LSZ 34 1.34 Flow
D1WWED02E 37
DPC130 DPC Series
Outlet section parts ordering codes _________________________________________________________________
DPC130/RD 3 1 - ......
3 1 2
1 2 3 4
2
1 Outlet section body * page 39 . 3 Ports options *

TYPE CODE DESCRIPTION TYPE CODE DESCRIPTION
RF 3FIA731000 Without ports 0 - Without ports; for RF section
RC 3FIA731310 With ports P1 and T1 1 3XTAP732200 G3/4 plug (nr.2); ports P1 and T1 pluggd
RD 3FIA731320 With ports P1, T1 and LS1 2 3XTAP732200 G3/4 plug (nr.1); port P1 plugged and T1
open
2 Drain options page 39 3 3XTAP732200 G3/4 plug (nr.1); port P1 open and T1
plugged
TYPE CODE DESCRIPTION 4 - Ports P1 and T1 open
1 XTAP517460 Internal drain; to use with mechanical
controls
2 XTAP217160 Internal drain; to use with hydraulic
4 Section threading
controls Specify only if it is different from BSP standard (see page 5).
3 XCAR119611* External drain G1/4; for electrohydralic
controls
38 D1WWED02E
DPC Series DPC130
______________________________________________________________________________________________
Outlet section
Type RD31 Type RC31

With ports P1, T1 (plugged) and LS1. With ports P1, T1 (plugged).
External drain External drain
Y
L
Y

X X X = allen wrench 12 - 42 Nm (31 lbf)
Y = wrench 19 - 24 Nm (17.7 lbf)
max. 144.5
max. 5.69
125.5
4.94
X X Type RD31 Type RC31 Type RF30

71.5
2.82
T1 T1
0.366
9.3
1.89
48
1.46
37
9
0.354 P1 P1
42 86 Type RF30 L
1.65 1.42
115.5
Without ports, external drain
L L
4.55
12.7 Y L
0.50
1.26
32
L
20.1
0.80
0.21.7
5.5
100 8
3.94 0.315
Note: The port LS1 must not be plugged
(in case it’s not used it has to be connected LS1
to tank).
Drain options
F
Option 1 1 Option 2 2 Option 1 Option 2 Option 3

internal drain for internal drain for
mechanical controls hydraulic controls
M M
125.5
4.94
Option 33
external drain for
Dim. F electrohydraulic controls
Option
mm in
N
1 3.5 0.138
M = allen wrench 5 - 24 Nm (17.7 lbf)
2 3.5 0.138 N = wrench 19 - 24 Nm (17.7 lbf)
3 19 0.75
D1WWED02E 39
DPC200 DPC Series
Dimensional data and performance _________________________________________________________________
184.5 E
7.26
170 1.6 53 75
6.69 0.063 2.09 2.95
3.23
82
64.5
2.54
V1
L
36.5
1.44
0.98
25
V2 A2 A1
P
28.25
28.25
1.112
1.112
398.3
15.68
8.15
207
2.68
5.28
70.5
134
2.78
68
T
M12
37.75
1.486
35.25
1.388
B2 B1
19.25
0.758
36.5
1.44
6 36.5 21.5
0.236 1.44 0.85
93
3.66
189.5 F
7.46
E F Weight E F Weight
TYPE TYPE
mm in mm in Kg lb mm in mm in Kg lb
PA1501568/004
161020061
DPC200/1 124 4.88 220 8.66 39.5 87.1 DPC200/6 389 15.31 485 19.09 111 245
DPC200/2 177 6.97 273 10.75 53.8 117 DPC200/7 442 17.40 538 21.18 125 276
DPC200/3 230 9.06 326 12.83 68.1 150 DPC200/8 495 19.49 591 23.27 140 308
DPC200/4 283 11.14 379 14.92 82.4 182 DPC200/9 548 21.57 644 25.35 154 339
DPC200/5 336 13.23 432 17.01 96.7 213 DPC200/10 601 23.66 697 27.44 168 371
production allotment
P⇒T Pressure drop inlet compensator A(B)⇒T pressure drop
product code
(margin pressure) (standard spool @ max.stroke)
0 10 20 30 40 50 60 (US gpm) 0 10 20 30 40 50 60 (US gpm)
20 60
(psi) (psi)
(bar) (bar)
250 750
15 45
200 600
Pressure
10th section
Pressure
10 150 30 450
5th section
100 300
5 15
50 150
1st section
0 0 0 0
0 40 80 120 160 200 240 (l/min) 0 40 80 120 160 200 240 (l/min)
Flow Flow
40 D1WWED02E
DPC Series DPC200
__________________________________________________________________________________________
Hydraulic circuit
Open center configuration example
B2 A2 B1 A1
P T
M
V2
L
V1
VB2 VB1
LS
VA2 VA1
Open center circuit and proportional hydraulic control with lever, with unloader
valve and port valves arrangement
Closed center configuration example
B2 A2 B1 A1
P T
M
V2
L
V1
EVB2
EVB1
LS
EVA2 EVA1
LSA LSB LSA LSB

Closed center circuit and one-side proportional electrohydraulic control with
lever, with unloader valve and pressure reducing valve, anticavitation valves on
all ports, L.S. relief valves on 2th section, LSA and LSB ports, internal pilot and
external drain
D1WWED02E 41
DPC200 DPC Series
Complete sections ordering codes ___________________________________________________________________
DPC200/3/ BR2-10(H220\ELP) / C10-104(200\200)-8EZ3TLG1/...... / RF30-......-12VDC-<SB20-CVN>
Valve type 1 2 3 4 5 6
Nr. of working sections The valve is supplied painted,

as standard, with one coat of
Primer black antirust paint
Tie rods tightening

7
2
42 D1WWED02E
DPC Series DPC200
1 Inlet section * page 44 4 Valve threading

Closed Center circuit Specify threading only if it is different from BSP standard (see page
TYPE: DPC200/BR2-10(H220\ELP)-12VDC CODE: 638203001 5).
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve For valve with ISO 6162-1 type 1 flange connection digit: FS3-
and 12VDC solenoid operated unloader valve, with P-T-LS ports open M(BSP).
TYPE: DPC200/BRF2-30(H220\ELP)-12VDC CODE: 638203002
DESCRIPTION: Without compensator, with L.S. pressure relief valve 5 Voltage
and 12VDC solenoid operated unloader valve, with P-T-LS ports open
Open Center circuit Specify the voltage of electric devices.
TYPE: DPC200/BR1-10(H220\ELP)-12VDC CODE: 638203003
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve 6 Pump stand-by
and 12VDC solenoid operated unloader valve, with P-T-LS ports open This option must be specified only if valve is configured for Closed
Center circuit, without local compensation and if the value is different
2 Working section * page 50 from 11.5 bar (167 psi)
TYPE: DPC200/C10-104(200\200)-8EZ3TLG1-12VDC
CODE: 638103001 7 Assembling kit
DESCRIPTION: With 2-way compensator, double acting spool for CODE CODE DESCRIPTION
200 l/min (52.8 US gpm), prop. electrohydraulic control with lever. With inlet section type
TYPE: DPC200/F32-503(150\150)-8EZ3TLG1.ULTULT.STST-12VDC Type BR Type BRF
CODE: 638103002 5TIR112215 5TIR112175 For 1 working section valve
DESCRIPTION: With 2-way compensator, floating spool for 150 l/min 5TIR112268 5TIR112228 For 2 working sections valve
(39.5 US gpm), proport. electrohydraulic control with lever, arranged 5TIR112321 5TIR112281 For 3 working sections valve
for "UL" size valves and L.S. relief valves, with LSA-LSB ports 5TIR112374 5TIR112334 For 4 working sections valve
5TIR112427 5TIR112387 For 5 working sections valve
3 Outlet section * page 65 5TIR112480 5TIR112440 For 6 working sections valve
For valve with mechanical control 5TIR112533 5TIR112493 For 7 working sections valve
TYPE: DPC200/RF10 CODE: 638303001 5TIR112586 5TIR112546 For 8 working sections valve
DESCRIPTION: Without ports 5TIR112639 5TIR112599 For 9 working sections valve
For valve with hydraulic control 5TIR112692 5TIR112652 For 10 working sections valve
TYPE: DPC200/RF20 CODE: 638303002
DESCRIPTION: Without ports, internal drain
TYPE: DPC200/RD21 CODE: 638303004
DESCRIPTION: With port P1, T1 (plugged) and LS1, internal drain
For valve with electrohydraulic control
TYPE: DPC200/RF30 CODE: 638303003
DESCRIPTION: Without ports, external drain L
TYPE: DPC200/RD31 CODE: 638303005
DESCRIPTION: With port P1, T1 (plugged) and LS1, external drain L
D1WWED02E 43
DPC200 DPC Series
Inlet section parts ordering codes _ _________________________________________________________________
Valve setting (bar)
DPC200 / BR1 - 1 0 (H220\ELP\......\SB15)-......-12VDC DPC200/BR2 - 1 0 (H220\ELP\......)-......-12VDC
1 2 3 5 6 7 4 8 9 1 2 3 5 6 7 8 9
5 5
7 7
1 1
6 6
9 9
DPC200/BRF2 - 3 0 (H220\ELP\......)-......-12VDC
1 2 3 5 6 7 8 9
Circuit conversion kit

6
9
7
10
44 D1WWED02E
DPC Series DPC200
___________________________________________________________________
Inlet section parts ordering codes
1 Inlet section body kit* page 46 6 Solenoid operated unloading valve page 48
Open Center circuit Needs coil type BER: see chapter 9
TYPE: DPC200/BR1-1 CODE: 5FIA620302 TYPE CODE DESCRIPTION
DESCRIPTION: With compensator, pressure reducing valve ELN 0EC08002031 Without emergency override
arrangement, P-T-LS ports (LS plugged), arranged for unloader valve ELP 0EC08002033 With push-button emergency override
TYPE: DPC200/BR1-1-FS3-M(BSP) CODE: 5FIA620303 ELT 0EC08002035 With “twist & push” emergency override
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connector ELV 0EC08002034 With screw type emergency override
Closed Center circuit LT XTAP510320 Unloading valve blanking plug
TYPE: DPC200/BR2-1 CODE: 5FIA620304
DESCRIPTION: With compensator, pressure reducing valve 7 Pressure reducing valve page 48
arrangement, P-T-LS ports, arranged for unloader valve
TYPE: DPC200/BR2-1-FS3-M(BSP) CODE: 5FIA620305 TYPE CODE DESCRIPTION
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. - 4AC9539900 Pressure reducing valve, 32 bar - 464 psi
TYPE: DPC200/BRF2-3 CODE: 5FIA620306 RT 3XTP3535100 Valve blanking plug (SAE 08/3)
DESCRIPTION: Without compensator, with pressure reducing valve
arrangement, P-T-LS ports, arranged for unloader valve 8 Section threading
TYPE: DPC200/BRF2-3-FS3-M(BSP) CODE: 5FIA620307 Specify threading only if it is different from BSP standard.
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. For section with ISO 6162-1 type 1 flange connection digit: FS3-
M(BSP).
2 Port arrangement
TYPE DESCRIPTION 9 Coil
1 With upper T and P ports (for section BR) TYPE CODE DESCRIPTION
3 With side T and P ports (for section BRF) 12VDC 4SLE001200 Coil type BER, ISO4400 conn., 12VDC
For complete available coils list see page 70.
3 Port options
TYPE DESCRIPTION 10 Circuit conversion kit
0 Ports P and T open These kits are NOT available for BRF section.
1 Port P open, port T plugged CODE DESCRIPTION
5KIT200311 For circuit conversion from Open Center to Closed
4 Compensator stanb-by Center: for BR and BN1 sections
Specify value only if it's different from the standard (11.5 bar - 167 5KIT200310* Kit for circuit conversion from Closed Center to Open
psi): for Open Center sections Center: for BR and BN2 sections
5 L.S. relief valve page 49

Standard setting is referred to 10 l/min (2.6 US gpm) flow.
TYPE ID CODE DESCRIPTION
LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600
psi), standard setting 90 bar (1300 psi)
XCAR126213 As prev., range 180-350 bar (2600-5100 psi),
LSZ Z 5CAR126221 With anti-tamper cap, range 40-180 bar
5CAR126219 As prev., range 180-350 bar (2600-5100 psi),
D1WWED02E 45
DPC200 DPC Series
Inlet section _ ______________________________________________________________________________________________
Example of BR section type
Y Z
Y
max. 202
max. 7.95
6.69
170
132.5
5.22
126.5
4.98
LS
4.37
111
3.66
3.50
93
89
78.5
3.09
X
1.85
47
5 19.25 19.25 8.75

X
0.63
0.47
0.197 0.758 0.758 0.344

16
12
23.75
0.935
36.5 134
1.44 5.28 M12 nr.2 threads
Auxiliary ports specification 9.75 35.25 70.5 28.25
M = G1/4 pressure gauge connection 0.384 1.388 2.78 1.112
Y
V1 = G1/4 pilot pressure port (Pmax =
48.5
30 bar - 435 psi) for hydraulic pilot control
1.91
T
valves feeding (P⇒OUT) p
0.71
3.35
18
V2 = M14x1.5 pilot pressure port for
85
electrohydraulic controls optional feeding
0.098
(Pmax = 315 bar - 4600 psi) (P⇒IN):
0.236
2.5
6
needs G1/4 joint, code 5GIU519611.
21.5
0.85
LS
W 207 82
8.15 3.23
max. 380
max. 14.96
Closed center Open center Wrenches and tightening torque

configuration example configuration example X = allen wrench 17 - 42 Nm (31 lbft)
BR2-10(H220\ELN) BR1-10(H220\ELN) Y = allen wrench 6 - 24 Nm (17.7 lbft)
Z = allen wrench 5 - 24 Nm (17.7 lbft)
W = wrench 19 - 24 Nm (17.7 lbft)
P T P T NOTE: for valves wrench and torque see pages 48-49.
M M
V2 V2
FS3-M(BSP) optional connection
35.25 70.5
V1 V1 1.39 2.78
13.1
0.52
11.1
0.44
T P
26.2
22.2
1.03
0.87
0.24
6
LS
LS 26.2 23.8
0.94 M10
1.03
nr. 4+4 threads
LS 52.4 47.6
2.06 1.87
46 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
Example of BRF section type

Y
R
6.34
161
152.5
6.00
4.29
109
3.23
80.5
82
3.17
64.5
2.54
2.28
58
1.85
47
34.5
1.36
7.1 4 15
0.63
0.47
0.280 0.157 0.59

16
12
89 17.25 95.5 21.25

3.50 0.679 3.76 0.837
max. 323
max. 12.72
36.5 134
20.1
0.79
1.44 5.28
V1 = G1/4 pilot pressure port (Pmax = 30 bar -
435 psi) for hydraulic pilot control valves feeding
49.5
1.95
(P⇒OUT)
0.23
5.9
max. 135
max. 5.31

18.5
0.73
11.1
0.44
R = allen wrench 10 - 24 Nm (17.7 lbft) Y
15
0.59
Y = allen wrench 6 - 24 Nm (17.7 lbft) W LS
W = wrench 19 - 24 Nm (17.7 lbft)
NOTE: for valves wrench and torque see pages
48-49.
207 82
8.15 3.23
Configuration Configuration FS3-M(BSP) optional connection

BRF2-30(H220\ELN) BRF2-30(H220\ELT\RT)
52.4 47.6
2.06 1.87
M10 26.2 23.8
P T P T nr. 4+4 threads 1.03 0.94
13.1
M M
0.52
26.2
1.03
V1 V1
4.29
109
22.2
0.87
38.6
1.52
11.1
0.44
LS LS
17.25 89 27.75
0.689 3.50 1.093
D1WWED02E 47
DPC200 DPC Series
Inlet section_ _______________________________________________________________________________________________
Pressure reducing valve
Type RT Reduced pressure vs. Flow

Pressure reducing valve valve blanking plug
0 0.8 1.6 2.4 3.6 (US gpm)
60
2 1 1 (bar) 800
3 (psi)
Reduced pressure
2 3 45
600
F
F
30
400
On BR section
On BRF section 15 200
0 0
0 3 6 9 12 15 (l/min)
82 Flow
3.23
82
3.23
Features
Reduced press. range . . : from 3.5 to 35 bar
(from 50 to 500 psi)
Max. inlet pressure. . . . : 420 bar (6100 psi)
Nominal flow . . . . . . . . : 15 l/min (4 US gpm)

F = wrench 24 - 30 Nm (22 lbf))
118.5 118.5
4.67 4.67
Solenoid operated unloading valve
ELN ELP
F
1 1 1
On BR section On BRF section
2 2
G
1 1
A
2 2
C
ELV ELT
E LT
1 1
2 2
1 1
2 2
B D
Wrenches and tightening Legenda
torques ELN: without emergency
F = wrench 24 - 30 Nm (22 lbf) ELP: push button emergency override
G = manual tightening ELV: screw emergency override BR section BRF section
E = wrench 10 - 24 Nm (17.7 lbf) ELT: “push&twist” emergency override Valve
A B C D
LT: valve blanking plug type
mm in mm in mm in mm in
Features ELN 65.5 2.58 102 4.02 60 2.36 89 3.50
Max. flow. . . . . . . . : 40 l/min (10.6 US gpm) ELP 88.5 3.48 125 4.92 83 3.27 112 4.41
Max. pressure. . . . . : 380 bar (5500 psi)
ELV 88.5 3.48 125 4.92 83 3.27 112 4.41
Internal leakage. . . : 0.25 cm3/min @ 210 bar (0.015 in3/min @ 3050 psi)
For coil features and options see coil BER at page 70. ELT 91 3.58 127.5 5.02 85.5 3.37 114.5 4.51
48 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
L.S. pressure relief valve
On BR section On BRF section
LSH LSD C
A
W Y
Y Y
X X
J J
B
LSZ ST
cap part K
4COP116420
X J
D
J
Legenda
BR section BRF section
LSH: with lock arrangement Valve
LSD: with blind nut A B C D
type
LSZ: with anti-tamper cap mm in mm in mm in mm in
LSD 19.5 0.77 189.5 7.46 21.5 0.85 58 2.28
X = wrench 13 - 24 Nm (17.7 lbf) LSH 15 0.59 185 7.28 16 0.63 52.5 2.07
Y = wrench 10 - 9.8 Nm (7.2 lbf) LSZ 32 1.26 202 7.95 34 1.34 70.5 2.78
W = allen wrench 3
J = wrench 7 - 24 Nm (17.7 lbf)
Pressure vs. flow diagram

(1) = valve range 40-180 bar (580-2600 psi)
0 20 40 60 (US gpm)
400 (psi)
(bar) max. setting(2)
5000
300 medium range setting(2)
4000
Pressure
200 max. setting (1) min. and std. setting (2) 3000
2000
std. setting(1)
100
0 0
0 40 80 120 160 200 240 280 (l/min)
Flow
D1WWED02E 49
DPC200 DPC Series
Working section parts ordering codes_ _____________________________________________________________

Valve setting (bar)
Flow on ports A\B (l/min) port A port B port A port B
DPC200 / C22 - 104 (200\200) - 8EZ3T LG 1 . U100U320 . S250S250 - ...... - 12VDC
1 2 3A 4 5 6 7 3
3B Lever position: see page 60
8
6
2 2
1 1 3
4
1 Working section body kit* page 52

With compensator
2 Spool page 54
TYPE: DPC200/C10-FS3-M CODE: 5EL6209210 Flow is referred to 7 bar (102 psi) stand-by (margin pressure)
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. TYPE CODE DESCRIPTION
TYPE: DPC200/C11 CODE: 5EL6201311 Double acting with A and B closed in neutral position
DESCRIPTION: Without valves arrangement, with LSA-LSB ports 105 3CU4510025 25 l/min (6.6 US gpm) flow
TYPE: DPC200/C11-FS3-M(BSP) CODE: 5EL6209211 101 3CU4510051 50 l/min (13.2 US gpm) flow
DESCRIPTION: As previous, fwith ISO 6162-1 type 1 flange connect. 106 3CU4510075 75 l/min (19.8 US gpm) flow
TYPE: DPC200/C22 CODE: 5EL6201322 102 3CU4510101 100 l/min (26.4 US gpm) flow
DESCRIPTION: Arranged for "U" size valves and L.S. relief valves, 107 3CU4510125 125 l/min (33 US gpm) flow
with LSA-LSB ports 103 3CU4510151 150 l/min (39.5 US gpm) flow
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. 104 3CU4510201 200 l/min (52.8 US gpm) flow
TYPE: DPC200/C32 CODE: 5EL6201332 Double acting with A and B to tank in neutral position
DESCRIPTION: Arranged for "UL" size valves and L.S.relief valves, 205 3CU4524025 25 l/min (6.6 US gpm) flow
with LSA-LSB ports 201 3CU4524050 50 l/min (13.2 US gpm) flow
TYPE: DPC200/F32 CODE: 5EL6204332 207 3CU4524125 125 l/min (33 US gpm) flow
DESCRIPTION: As Type C32, for floating circuit 203 3CU4524150 150 l/min (39.5 US gpm) flow
TYPE: DPC200/F32-FS3-M(BSP) CODE: 5EL6209232F 208 3CU4524175 175 l/min (46.2 US gpm) flow
Without compensator, with check valve Double acting with A and B partially to tank in neutral position
TYPE: DPC200/CV32 CODE: 5EL6201332A 2H05 3CU4525025 25 l/min (6.6 US gpm) flow
DESCRIPTION: Arranged for "UL" size valves and L.S. relief valves, 2H01 3CU4525050 50 l/min (13.2 US gpm) flow
with LSA-LSB ports 2H06 3CU4525075 75 l/min (19.8 US gpm) flow
TYPE: DPC200/CV32-FS3-M(BSP) CODE: 5EL6209232A 2H02 3CU4525100 100 l/min (26.4 US gpm) flow
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. 2H07 3CU4525125 125 l/min (33 US gpm) flow
TYPE: DPC200/FV32 CODE: 5EL6204332A 2H03 3CU4525150 150 l/min (39.5 US gpm) flow
DESCRIPTION: For floating circuit, arranged for "UL" size valves and 2H08 3CU4525175 175 l/min (46.2 US gpm) flow
L.S. relief valves, with LSA-LSB ports 2H04 3CU4525200 200 l/min (52.8 US gpm) flow
TYPE: DPC200/FV32-FS3-M(BSP) CODE: 5EL6209232FA
DESCRIPTION: As previous, with ISO 6162-1 type 11 flange connect. NOTE (*): Codes are referred to BSP thread.
50 D1WWED02E
DPC Series DPC200
______________________________________________________________
Working section parts ordering codes
2 Spool (continued) page 54 5 Port valves page 63

TYPE CODE DESCRIPTION TYPE CODE DESCRIPTION
Single acting on A, B plugged: needs G1 plug "U" size valves
305 3CU4530025 25 l/min (6.6 US gpm) flow UT XTAP522442 Valve blanking plug
301 3CU4530050 50 l/min (13.2 US gpm) flow C 5KIT410000 Anticavitation valve (for U cavity)
306 3CU4530075 75 l/min (19.8 US gpm) flow Fixed setting antishock and anticavitation valves: setting is referred
302 3CU4530100 100 l/min (26.4 US gpm) flow to 10 l/min (2.6 US gpm)
307 3CU4530125 125 l/min (33 US gpm) flow TYPE: U 100 CODE: 5KIT330 100
303 3CU4530150 150 l/min (39.5 US gpm) flow setting (bar) setting (bar)
308 3CU4530175 175 l/min (46.2 US gpm) flow SETTING:
304 3CU4530200 200 l/min (52.8 US gpm) flow 50 bar (725 psi) 63 bar (914 psi) 80 bar (1150 psi)
Double acting with A and B closed in neutral position, 4 100 bar (1450 psi) 110 bar (1590 psi) 125 bar (1800 psi)
positions, floating in 4th pos., spool in: needs working section 140 bar (2050 psi) 150 bar (2150 psi) 160 bar (2300 psi)
type F or FV, positioner and controls type 13 175 bar (2550 psi) 190 bar (2750 psi) 200 bar (2900 psi)
360 bar (5200 psi) 400 bar (5800 psi) 420 bar (6100 psi)
3A "A" side spool control kit page 56 "UL" size valves
ULT XTAP528520 Valve blanking plug
CL 5KIT409000 Anticavitation valve (for UL cavity)
Mechanical positioners
Fixed setting antishock and anticavitation valves with pressure relief
7FT 5V07200000 With friction and center position feeling
function: setting is referred to 5 l/min (1.3 US gpm)
8 5V08200000 3 position, spring return to neutral position
TYPE: UL 100 CODE: 5KIT340 100 L
13 5V13200000 For floating circuit (spool type 5), 4 pos.,
setting (bar) setting (bar)
detent in 4th position, with spring return to
SETTING:
neutral pos.
8IM 5V08200801* Range from 5.2 to 15.3 bar (75 to 222 psi)
13IM 5V13200800* For floating circuit (spool type 5), range
2.5 to 7 bar (75 to 222 psi), floating 11 bar
(160 psi) 250 bar (3600 psi) 270 bar (3900 psi) 300 bar (4350 psi)
3B Electrohydraulic controls page 58 380 bar (5500 psi)
Standard types 6 L.S. port relief valves page 64
8EZ3T-12VDC 5V08200721 With AMP integrated connector
Standard setting is referred to 10 l/min (2.6 US gpm) flow.
TYPE ID CODE DESCRIPTION
8EZ3T4-12VDC 5V08200722 With Deutsch integrated conn.
LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600
psi), standard setting 90 bar (1300 psi)
With digital spool position sensor#
8EZ3TSPSD-12VDC 5V08200725 With AMP integrated connector
8EZ3TSPSD-24VDC 5V08200745 With AMP integrated connector
8EZ3T4SPSD-12VDC 5V08200727 With Deutsch integrated conn.
8EZ3T4SPSD-24VDC 5V08200747 With Deutsch integrated conn.
With analog spool positions sensor#
8EZ3TSPSL-12VDC 5V08200625 With AMP integrated connector
LSZ Z 5CAR126221 With anti-tamper cap, range 40-180 bar
8EZ3TSPSL-24VDC 5V08200645 With AMP integrated connector
8EZ3T4SPSL-12VDC 5V08200627 With Deutsch integrated conn.
5CAR126219 As prev., range 180-350 bar (2600-5100 psi),
8EZ3T4SPSL-24VDC 5V08200647 With Deutsch integrated conn.
For floating circuit (spool type 5)
7 Section threading
13EZ3T4-24VDC 5V13200742 With Deutsch integrated conn. Specify threading only if it is different from BSP standard. For section
with ISO 6162-1 type 1 flange connection digit: FS3-M(BSP), only
4 "B" side spool control kit page 62 FS3-M for type C10

LG 5LEV200802 Cast iron lever box 8 Plug for single acting spool*
LGN 5LEV200801 Cast iron lever box, without lever CODE DESCRIPTION
L 5LEV200701 Aluminium lever box 3XTAP740210 G1 plug
4FL1066180 DN19 blind flange
D1WWED02E 51
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
Without port valves LS bottom ports position
0.47
12
(not for type C10) Z lever side
LSA
1.14
29
lever side
LSb
135.75 71.25
5.34 2.81
6.69
170
X = allen wrench 12 - 42 Nm (31 lbf)
Y = allen wrench 17 - 42 Nm (31 lbf)
3.43
87
X Z = allen wrench 6 - 24 Nm (17.7 lbf)
Y
FS3-M(BSP) optional connection
36.5
0.177
4.5
1.44 47.6
207 1.87
8.15 M10 23.8
nr. 4+4 threads 0.94 lever side
A B A B
2.09
22.2
0.87
53
26.5
1.04
26.5
1.04
11.1
0.44
64.75 68 74.25 68 74.25
2.549 2.68 2.923 2.68 2.923
With port valves

"U" and "UL" size valves have
the same position L.S. valve
10°
on port A
L.S. valve
on port B
17.95 46.8 48.5 25.75

0.707 1.84 1.91 1.014
Port B valve
0.67
A B
17
0.59
15
0.37
9.5
Port A valve 41.3 20.5 12.45

11.5
0.45
1.63 0.81 0.490
52 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
With compensator
Type C10 Type C11 Types C22 - C32 Type F32
B A B A B A B A
LSA LSB LSA LSB LSA LSB
Type CV11 Types CV22 - CV32 Type FV32
B A B A B A
LSA LSB LSA LSB LSA LSB
D1WWED02E 53
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
Spools
Spool type 1 Spool type 2 Spool type 2H

A, B closed in neutral position A, B open to tank in neutral pos. A, B partially to tank in neutral pos.
2 0 1 2 0 1 2 0 1
P P P
T T T T T T
A B A B A B
Spool type 3 Spool type 5

single acting on A floating in 4th position (pos.3)
2 0 1 2 0 1 3
P P
T T T T
A B A B
Spool stroke Spool stroke
position 1: - 8 mm (- 0.31 in) position 1: - 8 mm (- 0.31 in)
position 2: + 8 mm (+ 0.31 in) position 2: + 8 mm (+ 0.31 in)
position 3: - 13 mm (- 0.51 in)
54 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Spools
Following curves are detected with standard spools, connecting P⇒A⇒B⇒T and P⇒B⇒A⇒T ports without flow multiplication.
Customized spools with backpressure or flow multiplication may require different force, pressure and pilot current for
operation.
NOTE: for spools up to 120 l/min (31.7 US gpm), the effective flow on working ports may differ by 10% between the 1st an 10th
section.
Metering curves
Compensated working section - 3 positions spools
Qin = 260 l/min (68.7 US gpm)
With 8IM 222 200 150 100 75 0 75 100 150 200 222
(psi)
control kit
-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
250
(l/min) 60
H H (US gpm)
200
G G
45
F F
Port flow
150
E -2.2 mm 2.2 mm E
D -0.087 in 0.087 in D 30
100
C C
B B 15
50
A A
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 1 Spool stroke position 2
Pilot pressure
(bar)
With 8IM
15.3 15.0 12.0 9.0 6.0 5.2 0 5.2 6.0 9.0 12.0 15.0 15.3
control kit
Current (mA@12VDC)
1300 1200 1000 800 650 0 650 800 1000 1200 1300
With 8EZ3T
control kit (mA@24VDC)
650 600 500 400 325 0 325 400 500 600 650
Non-compensated working section

Spool flow vs. Stand-by pressure
(margin pressure)
0 100 200 300 400 (psi)
250
102 H G F E
(l/min) 60
D (US gpm) Spool nominal flow @ 7 bar (102 psi)
200 stand-by (margin pressure)
50
C A = 25 l/min (6.6 US gpm)
Port flow
150 40 B = 50 l/min (13.2 US gpm)

C = 75 l/min (19.8 US gpm)
B 30
100 D = 100 l/min (26.4 US gpm)
20 E = 125 l/min (33 US gpm)
A
50 F = 150 l/min (39.5 US gpm)
10 G = 175 l/min (46.2 US gpm)
0 0 H = 200 l/min (52.8 US gpm)
0 5 10 15 20 25 30 (bar)
7 Pressure
D1WWED02E 55
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
With friction and center position feeling: type 7FT
2 0 1
17.5
0.69
X
Y
W Z
3.43
87
113.5
4.47
Features Wrenches and tightening torques

Friction load adjusting. . . . . . . : 20-150 N (4.5-34 lbf) X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Friction load std. setting . . . . . : 100 N (22.5 lbf) Y = wrench 24 - 42 Nm (31 lbf)
Center tap (more than load). . . : 100 N (22.5 lbf) Z = allen wrench 6
W = wrench 13 - 24 Nm (17.7 lbf)
With spring return to neutral position: type 8
2 0 1
Force vs. Stroke diagram

0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 (in)
(N) 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)

150
32
122.7 N (27.6 lbf) (lbf)
125
X
24
100
Force
65.3 N
75 (14.7 lbf) 16
50
(±0.087 in)
43.5 N
±2.2 mm
(9.8 lbf) 8
25
3.43
87
0 0
0 1 2 3 4 5 6 7 8 pos.2 (mm)
0 -1 -2 -3 -4 -5 -6 -7 -8 pos.1 (mm)
16 Stroke
0.63

56 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
With detent in 4th position (pos.3), for floating circuit: type 13

Need working section type F or FV and floating circuit spools type 5.
25.5
1.00 Y
2 0 1 3
X
3.43
87
52 Y
2.05

Y = wrench 17 - 24 Nm (17.7 lbf)
31 G1/4 Type 8IM

1.22 VB VA
X VA 2 0 1
1.06
27
VB
Type 13IM
For floating circuit
VB VA
85.5
3.37
2 0 1 3
3.43
87
26.5
Features (all types) 1.04
53
Max. pressure. . . . . . . . . . : 50 bar (725 psi)
2.09
Type 8IM: suggested pressure

Type 8IM: Stroke vs. Pressure diagram control curve: type 020
-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in) 0 0.05 0.10 0.15 0.20 0.25 0.3 (in)
20 (psi) 40 (psi)
35 bar (508 psi)
(bar) 250 (bar)
15.3 bar (222 psi) 500
15 30
Pressure
Pilot pressure
200 400
10 150 20 300
(0.30 in)
spool 15.3 bar (220 psi)

5.2 bar (75 psi) dead band 100 200
5
7.25 mm
10
(0.29 in)
4.3 bar
7.6 mm
50 (63 psi) 100

0.85 mm
0 0 (0.033 in)
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm) 0 2 4 6 8 (mm)
position 1 Stroke position 2 Pusher stroke
D1WWED02E 57
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
Following specifications are measured with:

• mineral oil of 46 mm2/s (46 cSt) viscosity at 40°C (104°F) temperature,
• 20°C (60°F) environmental temperature,
• standard spools, connecting P⇒A⇒B⇒T ports without flow multiplication,
• 12 VDC and 24 VDC nominal voltage with tolerance ± 10%.
Specifications Spool control type

8EZ3T 13EZ3T
Electric specifications
12 VDC 4.72 Ω 4.72 Ω

Coil impedance
24 VDC 20.8 Ω 20.8 Ω
12 VDC 1.5 A 1.5 A

Max. operating current
24 VDC 0.75 A 0.75 A
No load current consumption 0 0
Hysteresis max. (1)

internal drain 5% with lever 7% with lever
from 0 ⇒ 100% of stroke < 150 ms < 250 ms

Time response
from 100% ⇒ 0 of stroke < 80 ms < 125 ms
12 VDC 650 mA 400 mA

Min. flow control signal
24 VDC 325 mA 200 mA
12 VDC 1300 mA 600 mA

Max. flow control signal
24 VDC 650 mA 300 mA
12 VDC - 850 mA
Float flow control signal
24 VDC - 250 mA
low frequency 150 Hz 150 Hz

Dither frequency
high frequency 150 Hz - 350 mA 150 Hz - 350 mA
Insertion 100% 100%
Coil insulance Class H (180°C - 356°F) Class H (180°C - 356°F)
Connector type AMP JPT - Deutsch DT AMP JPT - Deutsch DT
Weather protection (connector) IP65 (type JPT) - IP69K (type DT) IP65 (type JPT) - IP69K (type DT)
Hydraulic specifications
Max. pressure 50 bar (725 psi) 50 bar (725 psi)
Max. back pressure on drain 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) for the calculation rules see "Appendix A" on page 74.
Listed electrohydraulic controls need CED100X or CED400X electronic unit; for information contact Sales Department.
58 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Electrohydraulic controls without on-board electronic: spool position sensor

The sensor can be ordered exclusively through the electrohydraulic controls; see page 23 for available control list.
SPSL sensor
The SPSL position sensor converts the spool movements into a voltage linear signal..
Working conditions SPSL sensor output signal

(V) -0.30 -0.20 -0.10 0 0.10 0.20 0.30 (in)
Voltage supply 5 VDC 5
4
Output voltage
Mechanical life 3x106 operation tolerance

(from -40°F to 221°F)
-8 -6 -4 -2 0 2 4 6 8 (mm)
Spool stroke
Output signal range from 0.5 to 4.5 V
Connector
linearity ± 5%
Deutsch DT04-4P
spool in neutral 2.5 ± 0.2 V 3 4
Pin Function
max. current 1 mA 1 + 5V
EMC compatibility ISO 13766 / ISO 14982 2 not connected
Mechanical vibrations, shock, bumps IEC 68-2-6,-27,-29 3 GND
2 1
4 signal OUT
SPSD sensor
The SPSD position sensor converts the spool movements into an electric digital signal.
SPSD sensor output signal

Working conditions
(%) -0.30 -0.20 -0.10 0 0.10 0.20 0.30 (in)
Voltage supply from 9 to 32 VDC 100
80
Battery voltage
operation tolerance
operation tolerance
Mechanical life 3x106


(from -40°F to 221°F)
-8 -6 -4 -2 0 2 4 6 8 (mm)
Spool stroke
Output signal type PNP
max. current 6 mA Connector
Deutsch DT04-4P
EMC compatibility ISO 13766 / ISO 14982 3 4
Pin Function
1 Out A
2 GND
3 VB +
2 1
4 Out B
D1WWED02E 59
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
Proportional controls, types 8EZ3T - 13EZ3T

Control Types
2
1
Y
Types
EVA
port A
EVB
port B
X
8EZ3T - 8EZ3T4
EVA
7.12
196
184.5
7.26
EVB
2 0 1
3.43
87
Types
13EZ3T - 13EZ3T4
For floating circuit
EVA
EVB
2 0 1 3
A B
58
2.28
Y = allen wrench 3 - 5 Nm (3.7 lbf)
Types 8EZ3T: Stroke vs. Current diagram

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
1600 800
(mA@12VDC) 1300 / 750 mA (mA@24VDC)
1200 600
spool
Current
dead band
800 400
650 / 325 mA
400 200
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
60 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Proportional control types 8EZ3TSPSD - 8EZ3TSPSL

For control features see previous page, for sensor specification and features see page 59.
Control Types
Types 8EZ3TSPSD - 8EZ3T4SPSD Types 8EZ3TSPSL - 8EZ3T4SPSL

CANbus interface Analog input
EVA EVA
EVB 2 0 1 EVB
2 0 1
#
U
G G
2
1
K J
EVA
bocca A
EVB
bocca B
7.12
196
184.5
7.26
X
3.43
87

X= allen wrench 5 - 9.8 Nm (7.2 lbf)
Y= allen wrench 3 - 5 Nm (3.7 lbf)
J= wrench 17 - 9.8 Nm (7.2 lbf)
K= allen wrench 4 - 9.8 Nm (7.2 lbf)
70
2.76
122.5
4.82
D1WWED02E 61
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
"B" side spool control kit
Cast iron standard lever box; type LG
2 0 1 3
Lever assembly position
3
See page 50 for specification
32
° in working section description
11
58.5 8° 0 15° 0
45° 30'
2.30 30
°
1
18
X
°3
0'
30
°
2
30°
3.43
87
3
62.5
2.46
W Z Y
54.5
2.15
°
30
X
104
4.09
B X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = allen wrench 3
Z = wrench 10 - 9.8 Nm (7.2 lbf)
0.83
21
W= allen wrench 4 - 6.6 Nm (4.9 lbf)

M8 R = wrench 8
Cast iron lever box, without lever; type LGN Aluminium lever box; type L
2 0 1 3 2 0 1 3
Dimensions are the Dimensions and lever

same of type LG positions are the same
of type LG
Z Y W Z Y
X
X
X X
B B
62 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Port valves
Antishock anticavitation valves, type U Type U, setting example

Anticavitation valve, type C (10 l/min - 2.6 Us gpm)
Type U
0 3 6 9 12 15 (US gpm)
antishock valve 500
420 bar (6100 psi) (psi)
(bar)
X 400 6000
max. 0.079
340 bar (4950 psi)

max. 2
Pressure
300 260 bar (3750 psi) 4500
210 bar (3050 psi)
200 3000
140 bar (2050 psi)
80 bar (1150 psi)
Type C 100 1500
6.69
170
anticavitation valve 25 bar (360 psi)

0
0
X 0 10 20 30 40 50 60 (l/min)
Flow
Types U-C, pressure drop

(in anticavitation)
0 3 6 9 12 15 (US gpm)
Type UT 20 (psi)
valve blanking plug (bar)
250
X 15
A B
0.67
17
200
Pressure
0.37
9.5
10 150
eC
Typ 100
17.95 46.8 48.5 25.75 5 U
ype 50
0.707 1.84 1.91 1.014 T
0 0
Wrenches and tightening torque 0 10 20 30 40 50 60 (l/min)
X = wrench 13 - 24 Nm (17.7 lbf) Flow
Y = wrench 19 - 42 Nm (31 lbf)
Antishock anticavitation valves with Type UL, setting example

pressure relief function, type UL (5 l/min - 1.3 Us gpm)
Anticavitation valve, type CL Type UL 0 10 20 30 40 (US gpm)
antishock valve 500
(psi)
(bar)
Y 400 380 bar (5500 psi) 6000
max. 0.43
max. 11
300 bar (4350 psi)

Pressure
300 4500
250 bar (3600 psi)
200 bar (2900 psi)
200 3000
150 bar (2150 psi)
100 bar (1450 psi)
100 1500
6.69
170
Type CL 50 bar (725 psi)

0 0
anticavitation valve 0 40 80 120 160 (l/min)
Y Flow
Types UL-CL, pressure drop

(in anticavitation)
0 10 20 30 40 (US gpm)
40 (psi)
(bar)
500
Type ULT
30
A B valve blanking plug U
L 400
Pressure
pe
Y Ty 300
20
CL
pe 200
Ty
10
100
valves position are the same of type U
0 0
0 40 80 120 160 (l/min)
Flow
D1WWED02E 63
DPC200 DPC Series
Working section_ __________________________________________________________________________________________
L.S. port relief valves
L.S. valve on port B

LSH LSD
L.S. valve
on port A W Y
Y Y
A
X X
J J
LSZ ST
6.69
170
K
6.18
157
cap part
4COP116420
X J
Legenda
LSH: with lock arrangement
0.59
15
LSD: with blind nut

11.5
0.45
LSZ: with anti-tamper cap

41.3 20.5 12.45 Wrenches and tightening torques
1.63 0.81 0.490 X = wrench 13 - 24 Nm (17.7 lbf)
Y = wrench 10 - 9.8 Nm (7.2 lbf)
dim. A W = allen wrench 3
Valve type J = wrench 7 - 24 Nm (17.7 lbf)
mm in
LSD 20 0.79
LSH 15.5 0.61
LSZ 32.5 1.28 Pressure vs. flow diagram
0 20 40 60 (US gpm)
400 (psi)
(bar) max. setting(2)
5000
300 medium range setting(2)
4000
Pressure
200 max. setting(1) min. and std. setting(2) 3000
2000
std. setting(1)
100
0 0
0 40 80 120 160 200 240 (l/min)
Flow
64 D1WWED02E
DPC Series DPC200
_________________________________________________________________
Outlet section parts ordering codes
DPC200 / RF 3 0 - ...... DPC200 / RD 3 1 - ......
1 2 3 4 1 2 3 4
3 1 2 3 1 2
2 2
3
1
1 Outlet section* page 66 3 Port options*

TYPE CODE DESCRIPTION TYPE: 0 DESCRIPTION: Without ports (only for RF type)
RF 3FIA720300 Without ports TYPE: 1 DESCRIPTION: Ports P1 and T1 plugged
RD 3FIA720302 With P1, T1 and LS1 ports PLUG CODE: 3XTAP740210 (G1) + XTAP750240 (G1-1/4)
RD-FS3-M(BSP) 3FIA720901 As previous, with ISO 6162-1 type 1 BLIND FLANGE CODE: 4FL1066180 (DN19) + 4FL1071190 (DN25)
flange connection TYPE: 2 DESCRIPTION: Port P1 plugged and T1 open
PLUG CODE: 3XTAP740210 (G1)
2 Drain options page 67 BLIND FLANGE CODE: 4FL1066180 (DN19)
TYPE: 3 DESCRIPTION: Port P1 open and T1 plugged
TYPE CODE DESCRIPTION PLUG CODE: XTAP750240 (G1-1/4)
1 XTAP517460 Internal drain; to use with mechanical BLIND FLANGE CODE: 4FL1071190 (DN25)
controls TYPE: 4 DESCRIPTION: Ports P and T open
2 XTAP217160 Internal drain; to use with hydraulic
controls
3 XCAR119611* External drain G1/4; for electrohydraulic
4 Section threading
controls Specify threading only if it is different from BSP standard.
For section with ISO 6162-1 type 1 flange connection digit: FS3-
M(BSP).
D1WWED02E 65
DPC200 DPC Series
Outlet section_ _____________________________________________________________________________________________
Type RD31 Type RF30

With ports P1, T1 (plugged) and LS1; external drain Without ports; external drain
Y L
L
X
171.5
6.75
6.34
161
4.29
109
1.85
47
34.5
1.36
0.63
16
21.25 12 5.25
X
0.47
12
0.837 0.47 0.207

8.29 X = allen wrench 12 - 42 Nm (31 lbf)
207
Y = wrench 19 - 24 Nm (17.7 lbf)
8.15
0.063
1.6
L Note: The port LS1 must not be

49.5
1.95
plugged (in case it’s not used it has

2.20
56
26.9
1.06
to be connected to tank).
M12
11.5 25 134
0.45 0.98 5.28
FS3-M(BSP) optional connection Type RD31 Type RF30
47.6 52.4 T2
1.87 2.06
23.8 26.2 3/8-16 UNC
0.94 1.04 nr. 4+4 threads
P2 L
L
26.2
1.03
13.1
0.52
4.29
109
22.2
4.29
38.5
1.52
11.1
0.44
27.75 17.25
1.093 0.679 LS1
49.5
1.95
76.5
3.01
66 D1WWED02E
DPC Series DPC200
______________________________________________________________________________________________
Outlet section
Drain options
Option 1 1
internal drain for
L mechanical controls Option 1 Option 2 Option 3
F
J
6.34
161
152.5
6.00
Option 2 2
L
internal drain for
hydraulic controls
Option 33
external drain for
Dim. F electrohydraulic controls
Option
mm in
N
1 3.5 0.138
2 3.5 0.138
3 19 0.75

J = allen wrench 5 - 24 Nm (17.7 lbf)
M = allen wrench 6 - 24 Nm (17.7 lbf)
N = wrench 19 - 24 Nm (17.7 lbf)
D1WWED02E 67
Special configurations DPC Series
Connection between DPC Series valves_____________________________________________________________

DPC200 directional valve DPC130 directional valve
DPC200/1/BR2-10(D220\ELP)/C30-104(200\200)-8EZ3TLG1.UTUT/EIR/C10-1S8EZ3TL1/RF30/DPC130/1-......
Nr. of working Inlet section Working section 1 Working Outlet Nr. of working
sections section section sections
directional valves common specification
....BSP-12VDC-<SB20-CVN> Tie rods tightening

DPC200 inlet section
DPC200 working section
DPC130 working section
DPC130 outlet section
3
1
Tie rods tightening

1 Intermediate section page 70 NOTE: the maximum number of working

TYPE CODE DESCRIPTION sections should not exceed 10 units
EIR 638403001 Section for assembling of DPC200 and
DPC130 in single directional valve; with LS
port
2 DPC200 side assembling kit 3 DPC130 side assembling kit

CODE CODE DESCRIPTION CODE DESCRIPTION
With inlet section type 5TIR108112 For 1 working section valve
Type BR Type BRF 5TIR108160 For 2 working sections valve
5TIR112180 5TIR112141 For 1 working section valve 5TIR108208 For 3 working sections valve
5TIR112235 5TIR112194 For 2 working sections valve 5TIR108256 For 4 working sections valve
5TIR112340 5TIR112300 For 4 working sections valve 5TIR108352 For 6 working section valve
5TIR112446 5TIR112407 For 6 working section valve 5TIR108448 For 8 working sections valve
68 D1WWED02E
DPC Series Special configurations
_____________________________________________________________
Connection between DPC Series valve
EVA1
EVA2 port A1
port A2
EVB2 EVB1
port B2 port B1
dim. E dim. F
1.30
sections
working
33
36.5
1.44
Nr. of
BR BRF
inlet section inlet section
A2 A1 P
L mm in mm in mm in
1 101.5 4.00 73.1 2.88 97 3.82
3.94
100
2 151.5 6.08 126.1 4.96 145 5.71

8.15
5.28
8.17 7.05 7.60
207
134
3 207.5 179.1 193
T
B2 4 260.5 10.26 232.1 9.14 241 9.49
5 313.5 12.34 285.1 11.22 289 11.38
6 366.5 14.43 338.1 13.31 337 13.27
B1 7 419.5 16.52 391.1 15.40 385 15.16
8 472.5 18.60 444.1 17.48 433 17.05
9 525.5 20.69 497.1 19.57 481 18.94
Ls
LS2
F 45 E
1.77
B2 A2 B1 A1
P T
M
V2
L
V1
EVA2
EVB1
LS
EVB2 EVA1
LSAB LS2 LSA LSB
D1WWED02E 69
Accessories DPC Series
Coils and connectors _ ___________________________________________________________________________________
Connectors
Coil type Voltage Packard Packard Fili uscenti
ISO4400 Deutsch DT AMP JPT
Weatherpack Metri-pack (senza conn.)
10 VDC 4SLE001000 - - - - -
4SLE001201(5)
4SLE001209(3-5)
4SLE001200 4SLE001203(5)
12 VDC 4SLE001202(6) 4SLE001210(2) 4SLE001214(2) 4SLE001207
4SLE001217(3) 4SLE001211(3-5)
4SLE001216(3-6)
4SLE001206(2)
4SLE002400 4SLE002401(5)
BER 24 VDC 4SLE002408(3) 4SLE002407(3-5) 4SLE002403(5) - - 4SLE002404
4SLE302400(1) 4SLE002402(6)
4SLE004800
48 VDC - - - - -
4SLE304800(1)
4SLE011000
110VDC - - - - -
4SLE311000(1)
4SLE022000
220 VDC - - - - -
4SLE322000 (1)
10 VDC 4SL3000100
4SL3000130(6)
4SL3000120 4SL3000122(5)
12 VDC 4SL3000134(3-6) 4SL3000124(2) 4SL3000127(2) 4SL300012C
4SL3000126(4) 4SL3001200(3-5)
4SL3000128(2)
4SL3000240 4SL3000249(6)
24 VDC 4SL3000248(5) - - 4SL3000246
4SL3030240(1) 4SL300024C(3-6)
BT 26 VDC 4SL3000260 - - - - -
4SL3000480
48 VDC - - - - -
4SL3030480(1)
4SL3001100
110 VDC - - - - -
4SL3031100(1)
4SL3002200
220 VDC - - - -
4SL3032200(1)
Mating connectors
Standard 4CN1009995 5CON140031 5CON003 - -
24VDC 4CN3010240 - - - -
48VDC 4CN3010480 - - - -
With rectifier
110VDC 4CN3011100 - - - -
220VDC 4CN3012200 - - - -
Notes: (1) supply with AC and use only with rectifier connector - (2) with flying leads - (3) with bidirectional diode - (5) with unidirectional diode
(5) integrated perpendicular type - (6) integrated parallel type
Type BER
Features
Nominal voltage tolerance : ±10%
ISO4400 connector DEUTSCH DT04 connector
Power rating. . . . . . . . . . : 19.2 W - 10/12/24/48/
(perpendicular type)
110/220 VDC
: 19 W - 24/110/220 RAC
: 19.2 W - 48 RAC
Max. operating current . . : 1.9 A - 10 VDC
2.68
59.5
2.34
68
47.5
1.87
: 1.61 A - 12 VDC
47.5
1.87
23.5
23.5
0.93
: 0.80 A - 24 VDC
0.93
: 0.40 A - 48 VDC
38.5 36 38.5 36 : 0.17 A - 110 VDC
1.52 1.42 1.52 1.42 : 0.09 A - 220 VDC
: 0.89 A - 24 RAC
DEUTSCH DT04 connector AMP JPT connector
: 0.45 A - 48 RAC
(parallel type)
: 0.19 A - 110 RAC
: 0.09 A - 220 RAC
Coil insulance. . . . . . . . . : Class H (180°C - 356°F)
Weather protection. . . . . : IP65 - ISO4400
68.3
2.69
60.5
2.38
: IP69K - Deutsch DT
47.5
47.5
1.87
1.87
: IP65 - AMP JPT

23.5
23.5
0.93
0.93
: IP67 - Weatherpack
38.5 36 38.5 36 : IP67 - Metri-pack
1.52 1.42 1.52 1.42 Insertion . . . . . . . . . . . . : 100%
70 D1WWED02E
DPC Series Accessories
_____________________________________________________________________________________
Coils and connectors
Type BER
Flying leads with Flying leads with PACKARD Flying leads with PACKARD
Flying leads DEUTSCH DT04 connector WEATHER-PACK connector METRI-PACK connector
200 150 150
7.87 5.91 5.91
11.81
300
47.5
1.87
23.5
0.93
38.5 36
1.52 1.42
Type BT
ISO4400 connector AMP JPT connector Features

Nominal voltage tolerance : ±10%
Power rating. . . . . . . . . . : 19 W - 10 VDC
: 21 W - 12/24/26 VDC
: 20.3 W - 48 VDC
52.5
53.25
2.07
2.10
40.5
1.59
40.5
: 17.3 W - 110 VDC

1.59
18.25
18.25
0.72
: 17.7 W - 220 VDC

0.72
: 19.9 W - 24 RAC
50 Ø 36.5 50 Ø 36.5
1.97 1.44 : 20.7 W - 48 RAC
1.97 1.44
: 20 W - 110 / 220 RAC
Max. operating current . . : 1.9 A - 10 VDC
Flying leads : 1.77 A - 12 VDC
DEUTSCH DT04 connector : 0.89 A - 24VDC
: 0.84 A - 26 VDC
: 0.43 A - 48 VDC
L
: 0.16 A - 110 VDC

: 0.08 A - 220 VDC
62.5
2.46
42.5
1.67
40.5
: 0.93 A - 24 RAC
1.59
18.25
19.5
0.77
0.72
: 0.47 A - 48 RAC
: 0.18 A - 110 RAC
50 Ø 36.5 50 Ø 37.5
: 0.09 A - 220 RAC
1.97 1.44 1.97 Ø 1.48
Coil insulance. . . . . . . . . : Class F (155°C - 311°F)
Weather protection. . . . . : IP65 - ISO4400
Dimension L : IP69K - Deutsch DT
Coil type
(mm) (in) : IP65 - AMP JPT
: IP67 - Weatherpack
12VDC 247 9.72
: IP67 - Metri-pack
24VDC 307 12.09 Insertion . . . . . . . . . . . . : 100%
Flying leads with Flying leads with Flying leads with

DEUTSCH DT04 PACKARD WEATHER-PACK PACKARD METRI-PACK
connector connector connector
170 215 145
6.69 8.46 5.71
D1WWED02E 71
Installation DPC Series
Installation and maintenance _________________________________________________________________________
The DPC Series valves are assembled and tested as per the technical specification of this catalogue.
Before the final installation on your equipment, follow the below re commendations:
- the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product
on a flat surface;
- In order to prevent the possibility of water entering the spool control kit, do not use high pressure wash down directly on the
valve;
- prior to painting, ensure plugs on normally open ports are tightly in place.
B
B
A A
L T L
T p
p
V1
V2
Ls
Ls V2
V1
FITTINGS TIGHTENING TORQUE - Nm / lbft

A and B LS signal port Hydraulic
THREAD TYPE P inlet port T outlet port L drain port
workports V pilot ports* control ports
BSP G 3/4 G 1/2 G 3/4 G 1/4 G 1/4 G 1/4
With O-Ring seal 90 / 66.4 50 / 36.9 90 / 66.4 25 / 18.4 25 / 18.4 25 / 18.4

With copper washer 90 / 66.4 60 / 44.3 90 / 66.4 30 / 22.1 30 / 22.1 30 / 22.1
DPC130
With steel and

70 / 51.6 60 / 44.3 70 / 51.6 16 / 11.8 16 / 11.8 16 / 11.8
rubber washer
1 1/16-12 7/8-14 1 1/16-12 9/16-18 9/16-18 9/16-18
UN-UNF
(SAE 12) (SAE 10) (SAE 12) (SAE 6) (SAE 6) (SAE 6)
With O-Ring seal 95 / 70 50 / 36.9 95 / 70 30 / 22.1 30 / 22.1 30 / 22.1
BSP G1 G1 G 1-1/4 G 1/4 G 1/4 G 1/4
With O-Ring seal 120 / 88.5 120 / 88.5 190 / 140 25 / 18.4 25 / 18.4 25 / 18.4
With copper washer 120 / 88.5 120 / 88.5 190 / 140 30 / 22.1 30 / 22.1 30 / 22.1
With steel and
120 / 88.5 120 / 88.5 190 / 140 16 / 11.8 16 / 11.8 16 / 11.8
rubber washer
DPC200
1 5/16-12 1 5/16-12 1 5/8-12 9/16-18 9/16-18 7/16-20

UN-UNF
(SAE 16) (SAE 16) (SAE 20) (SAE 6) (SAE 6) (SAE 4)
With O-Ring seal 150 / 111 150 / 111 200 / 147 30 / 22.1 30 / 22.1 18 / 13.3
SAE J518 code 61 3/4 [3/8-16 UNC] 3/4 [3/8-16 UNC] 1 [3/8-16 UNC]
ISO 6162-1 type 1 DN 19 [M10] DN 19 [M10] DN 25 [M10] - - -
[bolts threading]
28-40 / 20.7-29.5 28-40 / 20.7-29.5 37-48 / 27.3-35.4 - - -
(*) V2 port is M14x1.5 threading: tightenìng torque value is the same of G1/4 thread
NOTE – These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating
and surface finish.
72 D1WWED02E
DPC Series Installation
_________________________________________________________________________
Installation and maintenance
Series DPC working sections are arranged for external operation of LS signal through dedicated ports on the lower side of
sections.
For the maximum permissible length of the pipe please contact Sales Dpt.
DPC130 DPC130 DPC200

working section with working section (only C26) working section with
commen LS signal with independent LS signal independent LS signal
B A B A B A
LSAB LSA LSB LSA LSB
LSA LSA
lever side
lever side
lever side
LSAB LSb LSb
D1WWED02E 73
Appendicies DPC Series
Appendix A _ ________________________________________________________________________________________________
Electrohydraulic controls: hysteresis calculation rule

Hysteresis is calculated as difference between control currents (I2-I1), needed to reach 50% of nominal spool stroke, referred
to maximum control current IMAX, needed to reach 100% of spool stroke.
I2 is determined on spool stroke increase line, I1 is determined on spool stroke decrease line.
Example diagram for

data detection
Max stroke
Stroke
I2 - I1
Hysteresis % = x 100
50% of max stroke IMAX
0
0 I1 I2 IMAX
Current
74 D1WWED02E
DPC Series
D1WWED02E 75
5th edition May 2015 WWW.WALVOIL.COM
D1WWED02E

D1wwed02e DPC Ing Kbs New 28621

Uploaded by

Copyright:

Available Formats

D1wwed02e DPC Ing Kbs New 28621

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

D1wwed02e DPC Ing Kbs New 28621

Uploaded by

Copyright:

Available Formats

DPC

WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN

Advantages and options

For special options contact Sales Dept.

Working conditions _ _____________________________________________________________________________________

CAVITY ISO 1179 11926

Istallation and maintenace . . . . . . . . . . . . . . . page 72

Dimensional data and performance _________________________________________________________________

P⇒T Pressure drop inlet compensator

DPC130/3 280 11.02 296 11.65 25.3 55.8

DPC130/7 472 18.58 488 19.21 48.7 107.0

DPC130/8 520 20.47 536 21.10 54.8 121.0

Open center configuration example

Closed center configuration example

Complete sections ordering codes ___________________________________________________________________

Nr. of working sections The valve is supplied painted,

Tie rods tightening

1 Inlet section * page 12 3 Outlet section * page 38

Inlet section parts ordering codes _ _________________________________________________________________

Valve setting (bar)

DPC130 / BRF21 - S250 - BSP

1 Inlet section kit* page 14 3 Solenoid operated unloading valve page 19

Standard setting is referred to 10 l/min (2.6 US gpm flow).

NOTE (*): Codes are referred to BSP thread.

Inlet section_ _______________________________________________________________________________________________

Dimensions and hydraulic circuit

F = wrench 17 - 24 Nm (17.7 lbft) p

G = wrench 24 - 42 Nm (31 lbft)

Z = wrench 19 - 24 Nm (17.7 lbft) 36.5 43.5 11

1.44 1.71 0.43

Auxiliary ports specification

Pressure reducing valve diagram

Reduced pressure vs. Flow

Dimensions and hydraulic circuit

controls feeding (Pmax = 30 bar - 435 psi) (P⇒IN) T

Z = wrench 19 - 24 Nm (17.7 lbft)

Inlet section_ _______________________________________________________________________________________________

Dimensions and hydraulic circuit

Example of BRSOG21 section

X V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi)

Wrenches and tightening torque

K = allen wrench 5 - 24 Nm (17.7 lbft)

Pilot solenoid valves

ELT3 88.5 3.48

Dimensions and hydraulic circuit

Example of BRS section

needs G1/4 joint, code 5GIU519611 LS

Inlet section_ _______________________________________________________________________________________________

Dimensions and hydraulic circuit

Example of BRF section

Pressure reducing valve

Wrenches and tightening torque Pressure reducing valve features

Pressure reducing valve diagram

L.S. pressure relief valve

Solenoid operated unloading valve

On BR and BRS section

Working section parts ordering codes (mechanical, hydraulic)_ ____________________________

port A port B port A port B Valve setting (bar)

DPC130/C22-1S 8IM L 1 . U100U320 S250S250-......