SERVICE MANUAL

CX5000 series
CX6000 series

84386774A 11/05/2011
EN
 Contents

INTRODUCTION
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.10.A
PNEUMATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.20.A
ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A
ELECTRONIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A
FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A

ENGINE AND PTO IN ................................................................... B

EXHAUST SYSTEM Emissions control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.40.B

TRANSMISSION, DRIVE AND PTO OUT ........................................ C

TRANSMISSION Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.B
TRANSMISSION Hydrostatic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.F

PROCESS DRIVE Primary process drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.50.B

AXLES, BRAKES AND STEERING................................................. D

FRONT AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.10.A
REAR AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.12.A
2WD-4WD SYSTEM Hydrostatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.14.E

STEERING Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.20.C

STEERING Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.20.B

SERVICE BRAKE Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.30.C

PARKING BRAKE Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.32.B

FRAME AND CAB ........................................................................ E

USER PLATFORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.34.A
ENVIRONMENT CONTROL Heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.40.B

ENVIRONMENT CONTROL Air-conditioning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.40.C

FRAME POSITIONING ................................................................. F

FRAME LEVELLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F.30.A

TOOL POSITIONING .................................................................... G

84386774A 11/05/2011
 LIFTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.10.A
LEVELLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.30.A

CROP PROCESSING ................................................................... K

FEEDING Reel feeding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.25.B

FEEDING Header feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.25.D

FEEDING Feeder housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.25.E

THRESHING Conventional threshing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.40.B

SEPARATING Beating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.42.B

SEPARATING Rotary separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.42.C

SEPARATING Straw flow beater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.42.F

SEPARATING Straw walker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.42.E
CLEANING Primary cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.62.B

CLEANING Tailings return system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.62.C

STORING AND HANDLING Grain storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.60.B

UNLOADING Grain unloading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K.72.B

84386774A 11/05/2011
84386774A 11/05/2011
INTRODUCTION

84386774A 11/05/2011
1
 Contents

INTRODUCTION

Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Note to the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Basic instructions - Chain Wear Tables - Roller Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Conversion factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

84386774A 11/05/2011
2
 INTRODUCTION

Foreword
IMPORTANT INFORMATION
All repair and maintenance works listed in this manual must be carried out only by staff belonging to the NEW HOL-
LAND Service network, strictly complying with the instructions given and using, whenever required, the special tools.

Anyone who carries out the above operations without complying with the prescriptions shall be responsible for the
subsequent damages.

The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional or
local dealers, reject any responsibility for damages due to the anomalous behavior of parts and/or components not
approved by the manufacturer himself, including those used for the servicing or repair of the product manufactured
or marketed by the Manufacturer. In any case, no warranty is given or attributed on the product manufactured or
marketed by the Manufacturer in case of damages due to an anomalous behavior of parts and/or components not
approved by the Manufacturer.

No reproduction, though partial of text and illustrations allowed

84386774A 11/05/2011
3
 INTRODUCTION

Foreword
Technical Information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through CD-ROM and in paper manuals. A coding system called ICE has been
developed to link the technical information to other Product Support functions e.g. Warranty.

Technical information is written to support the maintenance and service of the functions or systems on a customers
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to the
technical information in this manual to resolve that customers concern, you will find all the information classified using
the new ICE coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).

By integrating this new ICE coding into technical information , you will be able to search and retrieve just the right
piece of technical information you need to resolve that customers concern on his machine. This is made possible by
attaching 3 categories to each piece of technical information during the authoring process.

The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to
describe e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model that the piece of technical information is written for.

Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customers concern on his
machine.

That information could be:

• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool

84386774A 11/05/2011
4
 INTRODUCTION

How to Use this Manual

This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.

Each Chapter is divided into four Information types:

• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assem-
blies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assem-
blies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hy-
draulic devices, components and assemblies.
• Service data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices,
components and assemblies.

Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by
a letter A, B, C etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.

SECTION
A - Distribution Systems
B - Power Production
C - Power Train
D - Travelling
E - Body and Structure
F - Frame Positioning
G - Tool Positioning
H - Working Arm
J - Tools and Couplers
K - Crop Processing
L - Field Processing
PRODUCT
Tractors X X X X X X X X
Vehicles with working arms: backhoes, X X X X X X X X X
excavators, skid steers, .....
Combines, forage harvesters, balers, .... X X X X X X X X X X
Seeding, planting, floating, spraying X X X X X X X X X
equipment, ....
Mounted equipment and tools, ..... X X X X

84386774A 11/05/2011
5
 INTRODUCTION

This manual contains these Sections. The contents of each Section are explained over the following pages.

Contents
INTRODUCTION
DISTRIBUTION SYSTEMS A
POWER PRODUCTION B
POWER TRAIN C
TRAVELLING D
BODY AND STRUCTURE E
TOOL POSITIONING G
CROP PROCESSING K

Section Contents
SECTION A, DISTRIBUTION SYSTEMS
This Section covers the main systems that interact with most of the functions of the product. It includes the central
parts of the hydraulic, electrical, electronic, pneumatic, lighting and grease lubrication systems. The components that
are dedicated to a specific function are listed in the Chapter where all the technical information for that function is
included.

SECTION B, POWER PRODUCTION

This Section covers all the functions related to the production of power to move the machine and to drive various
devices.

SECTION C, POWER TRAIN

This Section covers all the functions related to the transmission of power from the engine to the axles and to internal
or external devices and additional Process Drive functions.

SECTION D, TRAVELLING
This Section covers all the functions related to moving the machine, including tracks, wheels, steering and braking. It
covers all the axles both driven axles and non-driven axles, including any axle suspension.

SECTION E, BODY AND STRUCTURE

This Section covers all the main functions and systems related to the structure and body of the machine. Including
the frame, the shields, the operator's cab and the platform.

SECTION G, TOOL POSITIONING

This Section covers all the functions related to the final and/or automatic positioning of the tool once the tool is posi-
tioned using the Working Arm or the machine frame.

SECTION K, CROP PROCESSING

This Section covers all the functions related to crop processing.

84386774A 11/05/2011
6
 INTRODUCTION

Chapters
Each Chapter is identified by a letter and number combination e.g. Primary hydraulic power system A.10.A The first
letter is identical to the section letter i.e. Chapter A.10 is inside Section A, Distribution systems.
CONTENTS
The Chapter Contents lists all the technical data (specifications), functional data (how it works), service data (remove,
install adjust, etc..) and diagnostic data (fault codes and troubleshooting) that have been written in that Chapter for
that function or system on the machine.

Contents
DISTRIBUTION SYSTEMS
PRIMARY HYDRAULIC POWER SYSTEM_ 10.A.
TECHNICAL DATA
PRIMARY HYDRAULIC POWER SYSTEM - General specification (A.10.A)

FUNCTIONAL DATA

PRIMARY HYDRAULIC POWER SYSTEM - Dynamic description (A.10.A)

SERVICE
PRIMARY HYDRAULIC POWER SYSTEM - Hydraulic pump - Remove (A.10.A)

DIAGNOSTIC
PRIMARY HYDRAULIC POWER SYSTEM - Troubleshooting (A.10.A)

INDEX
The Chapter Index lists in alphabetical order all the types of information (called Information Units) that have been
written in that Chapter for that function or system on the machine.

Index
DISTRIBUTION SYSTEMS - A
PRIMARY HYDRAULIC POWER SYSTEM
PRIMARY HYDRAULIC POWER SYSTEM - Dynamic description (A.10.A)

PRIMARY HYDRAULIC POWER SYSTEM - General specification (A.10.A)

PRIMARY HYDRAULIC POWER SYSTEM -Hydraulic pump- Remove (A.10.A)

PRIMARY HYDRAULIC POWER SYSTEM - Troubleshooting (A.10.A)

Page Header and Footer

The page header will contain the following references:
• Section and Chapter description

The page footer will contain the following references:

• Publication number for that Manual, Section or Chapter.
• Version reference for that publication.
• Publication date
• Section, chapter and page reference e.g. A.10.A / 9

84386774A 11/05/2011
7
 INTRODUCTION

Note to the Owner

Engine repair information:
The engine repair information is not contained within this manual.
For engine repair information, please refer to the respective Service Manual for the engine type used in your vehicle.

Fault Code Resolution (FCR) information:

The FCR information is not contained within the paper version of the manual.
For FCR information, please refer to the Electronic Service Tool (EST) or the electronic version of this manual.

Electronic Service Tool (EST) information:

The EST information and how to handle Control Modules (CM) (e.g.: resetting of the CM, etc.) is not contained within
this manual.
For EST information, please refer to the Electronic Service Tool User's Guide.

84386774A 11/05/2011
8
 INTRODUCTION

Safety rules
PRECAUTIONARY STATEMENTS
Personal Safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or death.

Throughout this manual and on machine decals, you will find precautionary statements ("DANGER", "WARNING",
and "CAUTION") followed by specific instructions. These precautions are intended for the personal safety of you and
those working with you. Please take the time to read them.

DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. The color
associated with Danger is RED.
M1169A

WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. The
color associated with Warning is ORANGE.
M1170A

CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury. The color associated with Caution is YELLOW.
M1171A

FAILURE TO FOLLOW "DANGER", "WARNING", AND "CAUTION" INSTRUCTIONS MAY RESULT IN SERIOUS
BODILY INJURY, DAMAGE TO HEALTH OR DEATH.

NOTICE: Install new decals if the old decals are destroyed, lost painted over or cannot be read. When parts are
replaced that have decals make sure you install a new decal with each new part.

MACHINE SAFETY
NOTICE: The word "notice" is used to inform the reader of something they need to know to prevent minor machine
damage if a certain procedure is not followed.

The precautionary statements ("Important") is followed by specific instructions. This statement is intended for machine
safety.

INFORMATION
NOTE: Instructions used to identify and present supplementary information.

LEGAL OBLIGATIONS
This machine may be equipped with special guarding or other devices in compliance with local legislation. Some to
these require active use by the operator. Therefor, check local legislations on the usage of this machine.

ACCIDENT PREVENTION
Most accidents or injuries that occur in workshops are the result of non compliance to simple and fundamental safety
principles. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED by applying the fundamental
safety principles, acting with the necessary caution and care.

84386774A 11/05/2011
9
 INTRODUCTION

Accidents may occur with all types of machine, regardless of how well the machine in question was designed and
built.

DANGER
Shut down the machine, remove key, be sure all moving parts have stopped and all pressure in the systems
is relieved before cleaning, adjusting or lubricating the equipment. Failure to comply will result in death or
serious injury.
M871

SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND COMPONENTS - HY-

DRAULICS (EUROPEAN STANDARD EN982)
• Flexible hose assemblies must not be constructed from hoses which have been previously used as part of a
hose assembly.
• Do not weld hydraulic pipes: when flexible hoses or piping are damaged, replace them immediately.
• It is forbidden to modify a hydraulic accumulator by machining, welding or any other way.
• Before removing hydraulic accumulators for servicing, the liquid pressure in the accumulators must be reduced
to zero.
• Pressure check on hydraulic accumulators must be carried out by a method recommended by the accumulator
manufacturer.
• Take care not to exceed the maximum allowed pressure of the accumulator. After any check or adjustment,
check for leakages or gas in the hoses or pipes.

SAFETY RULES
General guidelines
• Carefully follow specified repair and maintenance procedures.
• When appropriate, use P.P.E (Personal Protective Equipment)
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts. It is advised to wear
approved safety clothing, e.g.: non-slip footwear, gloves, safety goggles, helmets, etc.
• Do not carry out repair operations with someone sitting in the driver's seat, unless the person is a trained tech-
nician who is assisting with the operation in question.
• Do not operate the machine or use any of the implements from different positions, other than the driver's seat.
• Do not carry out operations on the machine with the engine running, unless specifically indicated.
• Bring all hydraulic cylinders to the home positions (down, retracted, etc.) before engine shut down.
• Stop the engine and check that the hydraulic circuits are pressure-free before removing caps, covers, valves,
etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in the workshop or elsewhere should be built according to the applicable
standards and legislation.
• Disconnect the power take off (p.t.o). and label the controls to indicate that the machine is being serviced. Any
parts that are to be raises must be locked in position.
• Brakes are inoperative when manually released for repair or maintenance purposes. Use blocks or similar de-
vices to secure the machine in these conditions.
• Only use specified towing points for towing the machine. Connect parts carefully. Make sure that all pins and/or
locks are secured in position before applying traction. Never remain near the towing bars, cables or chains that
are operating under load.
• When loading or unloading the machine from the trailer (or other means of transport), select a flat area capable
of sustaining the trailer or truck wheels. Firmly secure the machine to the truck or trailer and lock the wheels in
the position used by the carrier.

84386774A 11/05/2011
10
 INTRODUCTION

• Electric heaters, battery-chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Keep bystanders away.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-inflammable, non toxic
commercially available solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Do not run the engine in enclosed spaces without suitable ventilation or exhaust extraction.
• Never use open flames for lighting when working on the machine or checking for leaks.
• All movements must be carried out carefully when working under, on or near the machine. Wear personal pro-
tective equipment (P.P.E.): helmets, goggles and special footwear.
• When carrying out checks with the engine running, request the assistance of an operator in the driver's seat.
The operator must maintain visual contact with the service technician at all times.
• If operating outside the workshop, position the machine on a flat surface and lock in position. If working on a
slope, lock the machine in position. Move to a flat area as soon as is safely possible.
• Damaged or bent chains or cables are unreliable. Do not use them for lifting or towing. Always use suitable
protective gloves when handling chains or cables.
• Chains should always be safely secured. Make sure that the hitch-up point is capable of sustaining the load in
question. Keep the area near the hitch-up point, chains or cables free of all bystanders.
• Maintenance and repair operations must be carried out in a CLEAN and DRY area. Clean up any water or oil
spillage immediately.
• Do not create piles of oil or grease-soaked rags as they represent a serious fire hazard. Always store rags in a
closed metal container.
• Before engaging the machine, make sure that there are no persons within the machine or implement range of
action.
• Empty your pockets of all objects that may fall accidentally unobserved into the machine inner compartments.
• When metal parts are sticking out, use protective goggles or goggles with side guards, helmets, special footwear
and gloves.
• When welding, use protective safety devices: tinted safety goggles, helmets, special overalls, gloves and
footwear. All persons present in the area where welding is taking place must wear tinted goggles. NEVER
LOOK DIRECTLY AT THE WELDING ARC WITHOUT SUITABLE EYE PROTECTION.
• Always disconnect battery ground terminal when welding.
• Metal cables tend to fray with repeated use. Always use suitable protective devices (gloves, goggles, etc.) when
handling cables.

84386774A 11/05/2011
11
 INTRODUCTION

Machine start-up.
• Never run the engine in confined spaces that are not equipped with adequate ventilation for exhaust gas ex-
traction.
• Never place the head, body, limbs, feet, hands or fingers near rotating and moving parts.

Hydraulic systems and fuel injection systems

• A liquid leaking from a tiny hole may be almost invisible but, at the same time, be powerful enough to penetrate
the skin. Therefore, NEVER USE HANDS TO CHECK FOR LEAKS but use a piece of cardboard or paper for
this purpose. If any liquid penetrates skin tissue, call for medical aid immediately. Failure to treat this condition
with correct medical procedure may result in serious infection or death.
• In order to check the pressure in the system use suitable instruments.

Wheels and Tires

• Make sure that the tires are correctly inflated at the pressure specified by the manufacturer. Periodically check
the rims and tires for damage.
• Stand away from (at the side of) the tire when checking inflation pressure.
• Do not use parts of recovered wheels as incorrect welding brazing or heating may weaken and eventually cause
damage to the wheel.
• Never cut or weld a rim mounted with an inflated tire.
• Deflate the tire before removing any objects that may be jammed in the tire tread.
• Never inflate tires using inflammable gases, as this may result in explosions and injury to bystanders.

Removal and Re-fitting

• Lift and handle all heavy parts using suitable hoisting equipment. Make sure that parts are sustained by appro-
priate hooks and slings. Use the hoisting eyebolts for lifting operations. Extra care should be taken if persons
are present near the load to be lifted.
• Handle all parts carefully. Do not put your hands or fingers between parts. Wear suitable safety clothing - safety
goggles, gloves and shoes.
• Avoid twisting chains or metal cables. Always wear safety gloves when handling cables or chains.

84386774A 11/05/2011
12
 INTRODUCTION

Basic instructions
SHIMMING
For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add up
the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or the rated value
indicated on each shim.

ROTATING SHAFT SEALS

For correct rotating shaft seal installation, proceed as follows:
• before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes
• thoroughly clean the shaft and check that the working surface on the shaft is not damaged
• position the sealing lip facing the fluid; with hydrodynamic lips, take into consideration the shaft rotation direction
and position the grooves so that they will deviate the fluid towards the inner side of the seal
• coat the sealing lip with a thin layer of lubricant (use oil rather than grease) and fill the gap between the sealing
lip and the dust lip on double lip seals with grease
• insert the seal in its seat and press down using a flat punch, do not tap the seal with a hammer or mallet
• whilst inserting the seal, check that it is perpendicular to the seat; once settled, make sure that it makes contact
with the thrust element, if required
• to prevent damaging the seal lip on the shaft, position a protective guard during installation operations

O-RING SEALS
Lubricate the O-RING seals before inserting them in the seats, this will prevent them from overturning and twisting,
which would jeopardize sealing efficiency.

SEALING COMPOUNDS
Apply one of the following sealing compounds on the mating surfaces marked with an X: RTV SILMATE,
RHODORSIL CAF 1 or LOCTITE™ PLASTIC GASKET. Before applying the sealing compound, prepare the
surfaces as follows:
• remove any incrustations using a metal brush;
• thoroughly de-grease the surfaces using one of the following cleaning agents: trichlorethylene, petrol or a water
and soda solution.

COTTER PINS
When fitting split cotter pins, ensure that the pin notch is positioned in the direction of the force required to stress the
pin. Spiral cotter pins do not require special positioning.

84386774A 11/05/2011
13
 INTRODUCTION

PROTECTING THE ELECTRONIC/ ELECTRICAL SYSTEMS DURING CHARGING OR WELD-

ING
To avoid damage to the electronic/electrical systems, always observe the following:
1. Never make or break any of the charging circuit connections, including the battery connections, when the engine
is running.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the unit or on any header attached
to the unit.
• Position the welder ground clamp as close to the welding area as possible.
• If welding in close proximity to a computer module, then the module should be removed from the unit.
• Never allow welding cables to lay on, near or across any electrical wiring or electronic component while
welding is in progress.
4. Always disconnect the negative cable from the battery when charging the battery in the unit with a battery
charger.
NOTICE: If welding must be performed on the unit, either the unit or the header (if it is attached), the battery ground
cable must be disconnected from the unit battery. The electronic monitoring system and charging system will be
damaged if this is not done.

Remove the battery ground cable. Reconnect the cable when welding is completed.

WARNING
Battery acid causes severe burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Antidote - EXTERNAL: flush with water. INTERNAL: drink large quantities of water or milk. Follow with milk
of magnesia, beaten egg or vegetables oil. Call physician immediately. EYES: flush with water for 15 minutes
and get prompt medical attention.
84-110

84386774A 11/05/2011
14
 INTRODUCTION

SPARE PARTS
Only use "CNH Original Parts" or " NEW HOLLAND AGRICULTURE Parts".

Only genuine spare parts guarantee the same quality, duration and safety as original parts, as they are the
same parts that are assembled during standard production. Only "CNH Original Parts" or " NEW HOLLAND
AGRICULTURE Parts" can offer this guarantee. When ordering spare parts, always provide the following information:
• Machine model (commercial name) and serial number
• part number of the ordered part, which can be found in the "Microfiches" or the "Spare Parts Catalogue", used
for order processing

TOOLS
The tools that NEW HOLLAND AGRICULTURE suggests and illustrate in this manual have been:
• specifically researched and designed for use with NEW HOLLAND AGRICULTURE machines
• essential for reliable repair operations
• accurately built and rigorously tested so as to offer efficient and long-lasting operation

By using these tools, Repair Personnel will benefit from:

• operating in optimal technical conditions
• obtaining the best results
• saving time and effort
• working in safe conditions
NOTE: Wear limit values indicated for certain parts should be considered to be recommended, but not binding. The
terms "front", "rear", "right-hand" and "left-hand" (when referred to different parts) are determined from the rear, facing
in the direction of travel of the machine during operation.

84386774A 11/05/2011
15
 INTRODUCTION

Torque
Minimum hardware tightening torques (in N m or lb in /lb ft) for normal assembly applica-
tions unless otherwise stated
NOTICE: Shown below is the suggested initial torque tightening sequences for general applications, tighten in se-
quence from item 1 through to the last item of the hardware.

The minimum hardware tightening torque on drawings, in specifications etc. have priority.
The applicable CNH Standard is ENS7001.

df5019-1 1

Metric hardware
Class 8.8 in N m (lb in or lb ft) Class 10.9 in N m (lb in or lb ft)
Nominal Plated nut Lock nut Hardened nut Plated nut Lock nut Hardened nut
Size
M3 1.3 N·m 0.7 N·m 1.2 N·m 1.8 N·m 0.9 N·m 1.6 N·m
(11.5 lb in) (6.2 lb in) (10.6 lb in) (15.9 lb in) (8.0 lb in) (14.2 lb in)
M4 2.9 N·m 1.6 N·m 2.6 N·m 4.2 N·m 2.3 N·m 3.7 N·m
(25.7 lb in) (14.2 lb in) (23.0 lb in) (37.2 lb in) (20.4 lb in) (32.7 lb in)
M5 5.9 N·m 3.2 N·m 5.3 N·m 8.5 N·m 4.6 N·m 7.6 N·m
(52.2 lb in) (28.3 lb in) (46.9 lb in) (75.2 lb in) (40.7 lb in) (67.3 lb in)
M6 10.1 N·m 5.5 N·m 9.1 N·m 14.5 N·m 7.9 N·m 13 N·m
(89.4 lb in) (48.7 lb in) (80.5 lb in) (10.7 lb ft) (69.9 lb in) (9.6 lb ft)
M8 24.5 N·m 13.5 N·m 22 N·m 35.1 N·m 19.3 N·m 31.5 N·m
(18.1 lb ft) (10.0 lb ft) (16.2 lb ft) (25.9 lb ft) (14.2 lb ft) (23.2 lb ft)
M10 48.7 N·m 26.8 N·m 43.8 N·m 69.5 N·m 38.2 N·m 62.5 N·m
(35.9 lb ft) (19.8 lb ft) (32.3 lb ft) (51.3 lb ft) (28.2 lb ft) (46.1 lb ft)
M12 85 N·m 46.7 N·m 76.5 N·m 121 N·m 66.5 N·m 108.9 N·m
(62.7 lb ft) (34.4 lb ft) (56.4 lb ft) (89.2 lb ft) (49.0 lb ft) (80.3 lb ft)
M14 135 N·m 74.2 N·m 121.5 N·m 193 N·m 106.1 N·m 173.7 N·m
(99.6 lb ft) (54.7 lb ft) (89.6 lb ft) (142.3 lb ft) (78.3 lb ft) (128.1 lb ft)
M16 210 N·m 115.5 N·m 189 N·m 301 N·m 165.5 N·m 270.9 N·m
(154.9 lb ft) (85.2 lb ft) (139.4 lb ft) (222 lb ft) (122.1 lb ft) (199.8 lb ft)
M18 299 N·m 164.4 N·m 269.1 N·m 414 N·m 227.7 N·m 372.6 N·m
(220.5 lb ft) (121.3 lb ft) (198.5 lb ft) (305.4 lb ft) (167.9 lb ft) (274.8 lb ft)
M20 425 N·m 233.72 N·m 382.5 N·m 587 N·m 322.8 N·m 528.3 N·m
(313.5 lb ft) (172.4 lb ft) (282.1 lb ft) (432.9 lb ft) (238.1 lb ft) (389.7 lb ft)
M22 579 N·m 318.4 N·m 521.1 N·m 801 N·m 440.5 N·m 720.9 N·m
(427 lb ft) (234.8 lb ft) (384.3 lb ft) (590.8 lb ft) (324.9 lb ft) (531.7 lb ft)
M24 735 N·m 404.2 N·m 661.5 N·m 1016 N·m 558.8 N·m 914.4 N·m
(542.1 lb ft) (298.1 lb ft) (487.9 lb ft) (749.4 lb ft) (412.1 lb ft) (674.4 lb ft)
M27 1073 N·m 590.1 N·m 967.5 N·m 1486 N·m 817.3 N·m 1337 N·m
(791.4 lb ft) (435.2 lb ft) (713.6 lb ft) (1096 lb ft) (602.8 lb ft) (986.1 lb ft)
M30 1461 N·m 803.5 N·m 1315 N·m 2020 N·m 1111 N·m 1818 N·m
(1077.6 lb ft) (592.6 lb ft) (969.9 lb ft) (1489.9 lb ft) (819.4 lb ft) (1340.9 lb ft)

84386774A 11/05/2011
16
INTRODUCTION

ZEIL06CS0136F0A 2

ZEIL06CS0135F0A 3

84386774A 11/05/2011
17
 INTRODUCTION

Basic instructions - Chain Wear Tables - Roller Chains

Chain Wear
The individual joints in a roller chain articulate as they enter and leave the sprockets. This articulation results in wear
on the pins and bushings. A material is worn away from these surfaces the chain will gradually elongate.

ZEIL10GH0003A0B 1
Chains do not "stretch" - material is removed from pin and bushing.

(1): 2x pitch
(2): 2x pitch + wear
(3): elongation due to pin and bushing wear.

Elongation is normal and may be minimized by proper lubrication and drive maintenance. The rate of wear is depen-
dent upon: the relationship between the load and the amount of bearing area between pin and bushing, the material
and surface condition of the bearing surfaces, the adequacy of lubrication and the frequency and degree of articulation
between pins and bushings.
The latter is determined by the quantity of sprockets in the drive, their speeds, the number of teeth and the length of
the chain in pitches.

ZEIL10GH0015A0A 2
Measurement of Chain For Wear Elongation

Relatively accurate wear measurements can be made by using the above illustration. Measure as closely as possi-
ble from the center of one pin to the center of another. The more pitches (pins) contained within the measurement
increase the accuracy. If the measured value exceeds the nominal by more than the allowable percentage the chain
should be replaced.
The maximum allowable wear elongation is approximately 3 % for most industrial applications, based upon sprocket
design. The allowable chain wear in percent can be calculated using the relationship: 200/ (N), where (N) is the
number of teeth in the large sprocket.
This relationship is often useful since the normal maximum allowable chain wear elongation of 3 % is valid only up to
67 teeth in the large sprocket. In drives having fixed center distances, chains running in parallel or where smoother
operation is required, wear should be limited to approximately 1.5 %.

84386774A 11/05/2011
18
 INTRODUCTION

For example, if 40 pitches (40 pins) of a #40 chain were measured and the result was 523 mm (20.6 in) or greater
(using 3 % as the maximum allowable wear), the chain should be replaced. Anything less than 523 mm (20.6 in)
would still be acceptable by most industrial standards.

WEAR LIMITS ON ROLLER CHAIN

Strand No. 40 Chain
No. 50 Chain (10A) No. 60 Chain (12A) No. 80 Chain (16A)
Length (08A)
in
New Replace New Replace New Replace New Replace
Pitches
508 mm 523 mm 635 mm 654 mm 762 mm 787 mm 1016 mm 1047 mm
40P (20.0 in) (20.6 in) (25.0 in) (25.7 in) (30.0 in) (31.0 in) (40.0 in) (41.2 in)
635 mm 654 mm 793 mm 817 mm 952 mm 981 mm 1270 mm 1308 mm
50P (25.0 in) (25.7 in) (31.2 in) (32.2 in) (37.5 in) (38.6 in) (50.0 in) (51.5 in)
762 mm 784 mm 952 mm 981 mm 1143 mm 1177 mm 1524 mm 1568 mm
60P (30.0 in) (30.9 in) (37.5 in) (38.6 in) (45.0 in) (46.3 in) (60.0 in) (61.7 in)
889 mm 914 mm 1111 mm 1144 mm 1333 mm 1371 mm 1778 mm 1828 mm
70P (35.0 in) (36.0 in) (43.7 in) (45.0 in) (52.5 in) (54.0 in) (70.0 in) (72.0 in)
1016 mm 1047 mm 1270 mm 1308 mm 1524 mm 1568 mm 2032 mm 2095 mm
80P (40.0 in) (41.2 in) (50.0 in) (51.5 in) (60.0 in) (61.7 in) (80.0 in) (82.5 in)
1143 mm 1177 mm 1428 mm 1473 mm 1714 mm 1765 mm 2286 mm 2355 mm
90P (45.0 in) (46.3 in) (56.2 in) (58.0 in) (67.5 in) (69.5 in) (90.0 in) (92.7 in)
1270 mm 1308 mm 1578 mm 1635 mm 1905 mm 1962 mm 2540 mm 2616 mm
100P (50.0 in) (51.5 in) (62.1 in) (64.4 in) (75.0 in) (77.2 in) (100.0 in) (103.0 in)

STANDARD ROLLER CHAIN SIZES - NEW CHAINS

Chain No. 150 Chain No. Pitch Width Roller Diameter
40 08A 12.7 mm (0.5 in) 7.9 mm (0.3 in) 7.9 mm (0.3 in)
50 10A 15.8 mm (0.6 in) 9.5 mm (0.4 in) 10.1 mm (0.4 in)
60 12A 19 mm (0.7 in) 12.7 mm (0.5 in) 11.9 mm (0.5 in)
80 16A 25.4 mm (1.0 in) 15.8 mm (0.6 in) 15.8 mm (0.6 in)
100 20A 31.7 mm (1.2 in) 19 mm (0.7 in) 19 mm (0.7 in)
120 24A 38.1 mm (1.5 in) 25.4 mm (1.0 in) 22.2 mm (0.9 in)
140 28A 44.4 mm (1.7 in) 25.4 mm (1.0 in) 25.4 mm (1.0 in)
160 32A 50.8 mm (2.0 in) 31.7 mm (1.2 in) 28.5 mm (1.1 in)
180 * 57.1 mm (2.2 in) 35.7 mm (1.4 in) 35.7 mm (1.4 in)
200 40A 63.4 mm (2.5 in) 38.1 mm (1.5 in) 39.6 mm (1.6 in)

* No. 150 Number does not exist.

84386774A 11/05/2011
19
 INTRODUCTION

Conversion factors
Length
1 mm = 0.0393 in 1 in = 25.4 mm
1 km = 0.621 miles 1 miles = 1.609 km
1m = 3.281 ft 1 ft = 0.3048 m

Area
1 ha = 2.471 ac 1 ac = 0.404 US fl oz
1 m² = 10.76 ft² 1 ft² = 0.0923 m²

Volume
1 litre = 0.26 US gal 1 US gal = 3.78 litre
1 litre = 0.0.28 Bu 1 Bu 35.23 litre
1 litre = 1.057 US quart 1 US quart = 0.9464 litre
1 cm³ (cc) = 0.061 in³ 1 in³ = 16.38 cm³ (cc)
1 m³ = 35.31 ft³ 1 ft³ = 0.028 m³
1 ml = 0.033 US fl oz 1 US fl oz = 29.57 ml

Mass
1 kg = 2.204 lb 1 lb = 0.4536 kg

Torque
1 N·m = 0.7376 lb ft 1 lb ft = 1.3558 N·m

Power
1 kW = 1.358 Hp 1 Hp = 0.746 kW

Pressure
1 bar = 100 kPa
1 bar = 14.505 psi 1 psi = 0.06894 bar

Temperature
1 °C = ((1.8 x ° C) + 32) °F 1 °F = (0.56 x (° F - 32)) °C

Flow
1 l/min = 0.2642 US gpm 1 US gpm = 3.7853 l/min

Speed
1 km/h = 0.62 mph 1 mph = 1.6 km/h

84386774A 11/05/2011
20
 INTRODUCTION

Product identification
EXPLANATION OF MACHINE SERIAL NUMBERS
Example : n° 101774001

10 1774001: The first two digits identify the model within a product line:

Model Tier 4 Tier 3

CX5080 10
CX5090 11 53
CX5090 Laterale 12
CX5090 Hillside 13
CX6080 15 19
CX6090 16 47
CX6090 Laterale 17

101 774001: The third digit indicates the product line.

CR-CX-CSX Combine harvesters: 1

TC Combine Harvester 9
Combine headers: 9
Forage Harvesters: 5
Large Square Balers: 4
Grass Pickup 3

101 774 001: These 3 digits indicate the batch in which the machine was made.

10 1774 001: Product line number 1 and batch 774 together form the series number 1774.

101774 001: The last 3 digits are a sequential number for each model within a batch.

Summarizing we can say that this machine is the first CX5080 of serie 1774.

84386774A 11/05/2011
21
INTRODUCTION

84386774A 11/05/2011
22
 SERVICE MANUAL
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS

CX5000 series
CX6000 series

84386774A 11/05/2011
A
 Contents

HYDRAULIC, PNEUMATIC, ELECTRICAL,

ELECTRONIC SYSTEMS - A

PRIMARY HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.10.A

CX5000 series , CX6000 series

PNEUMATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.20.A

CX5000 series , CX6000 series

ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A

CX5000 series , CX6000 series

ELECTRONIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A

CX5000 series , CX6000 series

FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A

CX5000 series , CX6000 series

84386774A 11/05/2011
A
HYDRAULIC, PNEUMATIC, ELECTRICAL,
ELECTRONIC SYSTEMS - A

PRIMARY HYDRAULIC POWER SYSTEM - 10.A

CX5000 series
CX6000 series

84386774A 11/05/2011
A.10.A / 1
 Contents

HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC

SYSTEMS - A

PRIMARY HYDRAULIC POWER SYSTEM - 10.A

TECHNICAL DATA

PRIMARY HYDRAULIC POWER SYSTEM

Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hydraulic pump
General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

FUNCTIONAL DATA

PRIMARY HYDRAULIC POWER SYSTEM

Hydraulic schema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hydraulic symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Component localisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Stack valve
Dynamic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Hydraulic pump
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Filter
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Breather
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

SERVICE

Stack valve
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Hydraulic pump
Disassemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

84386774A 11/05/2011
A.10.A / 2
Please Click Here

www.cnhmanualpdf.com

To Download Complete Manual

Feel free to Contact us

Support Email: [email protected]