II Year Hand Book FInal

SR ENGINEERING COLLEGE
(Autonomous institution)
Hand Book
II-B.Tech I-Sem
Electronics and Communication
Engineering
RA-15 Regulation
Course Accredited by NBA, Accredited by
NAAC with ‘A’ Grade, Approved by AICTE,
Affiliated to JNTU, Hyderabad
Ananthasagar, Warangal, Telangana – 506 371
I Semester: 12-06-2017 to 13-10-2017

SR Educational Group
The thirst for knowledge and the enthusiasm to go beyond and think 'out of the box' is
something that S R group encourages, nurtures and supports among our students.
S R Engineering College, Warangal was established in 2002 by S R Educational Society. It

is located on Warangal-Karimnagar highway at about 15 KM away from Warangal City. The
college is affiliated to JNTU, Hyderabad. It is running 5 undergraduate (B.Tech) and 7
postgraduate (M.Tech) engineering programs besides, Master of Business Administration
(MBA). Three undergraduate engineering programs are accredited by the National Board of
Accreditation (NBA) within a short span of six years of its establishment. The college was
recently sanctioned with two new integrated programs; a 5-year dual degree program in
Management (BBA+MAM) and a 5½ year dual degree program in engineering
(B.Tech+MTM). The college is granted Autonomous Status by University Grants
Commission (UGC) in 2014.
S R Engineering College (SREC) is an autonomous and accredited institution valuing and

encouraging creativity and quality in teaching and research. The staff and the students take on
new and interesting activities to acquire ability to think uniquely and independently. The
college is in a position to attract and develop outstanding faculty to actively participate and
interactively support an open academic climate in the campus. It adopts innovative
approaches for continuous improvement by strategic planning, benchmarking and
performance monitoring. The policy is to establish a system of quality assurance of its
graduates by continuously assessing and upgrading teaching and learning practices.
Through active industry cooperation, SREC has established centers like CISCO Networking
Academy, Microsoft Innovation Centre, IBM Centre of Excellence and NEN Centre for
Entrepreneurship Development for nurturing specific skill sets for employability. To shape
and transform the graduates to meet challenging and complex engineering tasks globally, the
college has built and fostered relationship with reputed universities like University of
Massachusetts, Saint Louis University, University of Missouri and Wright State University.
To align with ABET system of outcome based curriculum, many reforms have been
implemented in the course structure with due stress on basic sciences and humanities,
interdisciplinary and core engineering including projects and seminars in line with AICTE
guidelines.
The college is striving to create and support academic and research activities in thrust areas
like energy and environment. The institute has reliable, flexible and scalable technology
infrastructure for networking and web services which provides crucial support for improved
functioning and timely service to students and faculty. The centre for student services and
placements (CSSP) actively pursues training and campus placements by keeping in touch
with industry for internships and employment. The faculty is highly motivated to advance
their knowledge and qualifications through sponsored research. The digital library provides
the necessary resources and e-learning services. Regular seminars, webinars, workshops and
conferences and faculty development programs are conducted to encourage participation
from students and faculty from neighboring colleges.
S R Engineering College is implementing a strategic action plan with specific focus on:
1. Novel technology enabled teaching and learning techniques,

2. Strengthen existing PG programs through modernization of laboratories and training
of faculty and staff,
3. Identify and start new PG programs in current areas of research with immediate
relevance to the state and the country,
4. Attract funding for sponsored research from DST, MNRE, AICTE and UGC,
5. Strengthen functional areas like governance and administration, infrastructure,
finance etc.,
6. Network with industry and institutes of repute through academic partnership for
expanding avenues for internships and research.
VISION
To be among the Top 20 Private Engineering
Institutes in India by 2020
MISSION
 Design and implement curriculum that equips
students with professional and life skills
 Recruit, develop and retain outstanding faculty
to achieve academic excellence
 Promote and undertake quality research in thrust
areas of science and Technology
 Collaborate with industry and academia to meet
the changing needs of society
 Foster innovation and cultivate the spirit of
entrepreneurship among students
About The Department
The Department of ECE is one of the biggest department in the
college with highly experienced, qualified, dedicated, and trained
faculty with deep sense of commitment towards the Students and
Institution. The department has 56 staff members, 5 of whom are
Doctorates and 12 faculties are pursuing their higher qualifications
from various universities besides this most of the faculty were
executing research projects from various funding agencies like
AICTE,DST and UGC The main research of the department is in the
area of VLSI, Embedded Systems and Communications. The
department has four major projects from Department of Science and
Technology and one minor project from UGC. The department of
ECE has well equipped and state of the art laboratories for both UG &
PG programs. To cater the needs of the students several technical
talks, workshops, personality development programs, soft skills and
entrepreneurial activities are regularly conducted under professional
societies besides the curriculum. The Department has an Active IEEE
student branch and IETE Student forum.
The department has its own Vision and Mission at par with the
Vision and Mission of the Institute.
VISION
To be the leading Electronics and Communication
Engineering Department in promoting quality
education, research and consultancy
MISSION
 Design curriculum that provides effective
engineering education by promoting
innovating teaching-learning practices
 Establish centers of excellence in core areas
and take up consultancy and research
 Interact and work closely with industries,
research organizations to accomplish
technology transfer
 Impart necessary skills and promote
professional practices to enhance placement
and entrepreneurship
Program Educational Objectives (PEOs)
PEOs (Program Educational Objectives) relate to the career and professional

accomplishments of students after they graduate from the program.
Consequently, assessment and evaluation of the objectives requires assessment
tools that can be applied after graduation.
I. Enhance the skill set of students by providing strong foundation in

basic sciences, mathematics, engineering and use necessary tools to
solve engineering problems..
II. Equip students with ethical, professional behavior and mould them
to become successful qualified engineers.
III. Inculcate necessary aptitude and ability to equip students to use
their knowledge as a foundation for lifelong learning.
IV. Build team work skills and develop abilities to communicate and
deal with different professionals both nationally and globally.
Program Outcomes (POs):
Engineering Graduates will be able to:
1. Engineering Knowledge: Apply the knowledge of mathematics, science, engineering

fundamentals, and an engineering specialization to the solution of complex
engineering problems.
2. Problem Analysis: Identify, formulate, review research literature, and analyze
complex engineering problems reaching substantiated conclusions using first
principles of mathematics, natural sciences, and engineering sciences.
3. Design/Development of solutions: Design solutions for complex engineering
problems and design system components or processes that meet the specified needs
with appropriate consideration for the public health and safety, and the cultural,
societal, and environmental considerations.
4. Conduct investigations of complex problems: Use research-based knowledge and
research methods including design of experiments, analysis and interpretation of data,
and synthesis of the information to provide valid conclusions.
5. Modern Tools usage: Create, select, and apply appropriate techniques, resources, and
modern engineering and IT tools including prediction and modeling to complex
engineering activities with an understanding of the limitations.
6. The engineer and society: Apply reasoning informed by the contextual knowledge to
assess societal, health, safety, legal and cultural issues and the consequent
responsibilities relevant to the professional engineering practice.
7. Environment and sustainability: Understand the impact of the professional
engineering solutions in societal and environmental contexts, and demonstrate the
knowledge of, and need for sustainable development.
8. Ethics: Apply ethical principles and commit to professional ethics and responsibilities
and norms of the engineering practice.
9. Individual and team work: Function effectively as an individual, and as a member
or leader in diverse teams, and in multidisciplinary settings.
10. Communication: Communicate effectively on complex engineering activities with
the engineering community and with society at large, such as, being able to
comprehend and write effective reports and design documentation, make effective
presentations, and give and receive clear instructions.
11. Project Management and Finance: Demonstrate knowledge and understanding of
the engineering and management principles and apply these to one‟s own work, as a
member and leader in a team, to manage projects and in multidisciplinary
environments.
12. Life Long Learning: Recognize the need for, and have the preparation and ability to
engage in independent and life-long learning in the broadest context of technological
change.
Academic Calendar for II - IV B. Tech. I & II Semester
Academic Year 2017 – 18
I Semester
S. No. Description Schedule Duration

1 12.06.2017
Commencement of Class work --
2 12.06.2017 to 05.08.2017
1st Spell of Instruction 8 Weeks
3
1st Mid Examinations 08.08.2017 to
Timings: FN: 10.00 am to 11.30 am : AN:2.00 pm to 3.30 3 Days
pm
10.08.2017
4 2nd Spell of Instruction (Includes Dasara 11.08.2017 to
9 Weeks
Holidays) 11.10.2017
6
2nd Mid Examinations 12.10.2017 to
Timings: FN: 10.00 am to 11.30 am : AN:2.00 pm to 3.30 3 Days
pm
16.10.2017
End Semester Regular Examinations /
7 17.10.2017 to
Supplementary Examinations (Theory & 7 Weeks
02.12.2017
Practical)
Commencement of Class work for II, III, IV
8 --
B.Tech. II Sem. for the academic year 2016- 04.12.2017
2017
COUSE STRUCTURE
TIME TABLE
Department of Electronics and Communication Engineering
SR Engineering College
Academic Year 2017-18
Class: II-ECE-A Room No: 2216 w.e.f. 12-06-2017
2:30-
9:30-10:20 10:20-11:10 11:10-11:20 11:20-12:10 12:10-1:00 1:00-1:40 1:40-2:30 3:15-4:00
3:15
Day
I II BREAK III IV V VI VII
MON ECA BS/EDC Lab PTSP M-II NA
LUNCH BREAK
TUE NA S&S T&P ECA S&S Library
BREAK
WED M-II S&S PTSP ECA NA CED
THU PTSP CM LAB BS/EDC Lab

Gender
FRI S&S ECA PTSP NA M-II
BREAK
Sensitization
Sports/
SAT Media Project S&S M-II NA ECA
Library
Class Teacher : Mr. G. Mahesh Kumar
Subjects:
ECA(EC103) :Electronic Circuit Analysis: Mr. G.Mahesh Kumar
PTSP (EC104):Probability Theory and Stochastic Processes : Ms. Ch. Sridevi
S& S (ES105) : Signals and Systems: Mr. Leo Joseph
NA (EE135) : Network Analysis: Mr. PraveenKumar
M-II(BS109) :Mathematics II : Mr. Balaram
GS (MC102): Gender Sensitization :Ms.Kafila
Media project:
CED:Center for Enterpreurship Development:(Drawing hall block-I) Dr. N. Suman Kumar/Mr. G.Sathish Raj
T& P : : Mr. Syam B.Koleti
Labs:
BS (ES120) :Basic Simulation: Mr. Leo Joseph / Ms. D. Rajitha
EDCA (EC109):Electronic Devices & Circuit Analysis : Mr. G.Mahesh Kumar/ Ms. Ch. Sudharani
CM (BS111) : Computational Mathematics: Mr. Rajbir Singh
TIME TABLE
Class: II-ECE-B Room No: 2217 w.e.f.12-06-2017

9:30-10:20 10:20-11:10 11:10-11:20 11:20-12:10 12:10-1:00 1:00-1:40 1:40-2:30 2:30-3:15 3:15-4:00
Day
I II III IV V VI VII
BREAK
MON ECA PTSP M-II S&S BS/EDC Lab
LUNCH BREAK
TUE S&S CM LAB NA ECA
WED PTSP ECA S&S NA M-II CED

BREAK
THU M-II S&S NA ECA T&P Sports/Library
Gender
FRI NA BS/EDC Lab PTSP
Sensitization
Media
SAT ECA S&S BREAK M-II PTSP Sports/Library
Project
Class Teacher : Ms. P. Anuradha
Subjects:
ECA(EC103) :Electronic Circuit Analysis: Mr. S.Umamaheswar
PTSP (EC104) : Probability Theory and Stochastic Processes : Dr.Tarun Kumar
S& S (ES105) : Signals and Systems: Ms.P.Anuradha
NA (EE135) : Network Analysis: Mr.Raj Kumar
M-II(BS109) :Mathematics II : Ms. Anusha
GS (MC102): Gender Sensitization: Ms.G.Rajyalaxmi

Media project:
Labs:
BS (ES120) :Basic Simulation: Ms.P.Anuradha/Mr. P. Krishna
EDCA (EC109):Electronic Devices & Circuit Analysis : Mr. S.Umamaheswar/Ms. Ch. Sudharani

TIME TABLE
Class: II-ECE-C Room No: 2218 w.e.f.12-06-2017

9:30-10:20 10:20-11:10 11:10-11:20 11:20-12:10 12:10-1:00 1:00-1:40 1:40-2:30 2:30-3:15 3:15-4:00
Day
I II III IV V VI VII
Gender
BREAK
MON PTSP M-II S&S ECA NA

Sensitization
LUNCH BREAK
TUE ECA S&S NA M-II BS/EDC Lab
WED S&S ECA NA PTSP CED
THU PTSP BS/EDC Lab CM LAB

Sports/
FRI M-II S&S PTSP NA M-II ECA
Library
BREAK
SAT NA ECA Media Project T&P Sports/Library
Class Teacher : Mr. S. Umamaheshwar

Subjects:
ECA(EC103) :Electronic Circuit Analysis: Mr. S.Umamaheswar
PTSP (EC104) : Probability Theory and Stochastic Processes :: Mr.S.Srinivas
S& S (ES105) : Signals and Systems: Dr. Shankaranand Jha
NA (EE135) : Network Analysis: Ms.B.Satyavani
M-II(BS109) :Mathematics II : Ms. Rashmi Agarwal
GS (MC102): Gender Sensitization:Ms.G.Rajyalaxmi
Media project:
Labs:
BS (ES120) :Basic Simulation: Dr. Shankaranand Jha/ Ms. K. Hemalatha
EDCA (EC109):Electronic Devices & Circuit Analysis : Ms. Ch. Sudharani /Ms. G. Samatha
(BS109) MATHEMATICS-II
Hours / Week Marks

Year Semester C
L T P/D CIE SEE Total
II I 3 - - 3 30 70 100
COURSE DESCRIPTION:
The course is intended to cover topics in integral transforms, complex variables and vector
calculus. The topics included are those required for concurrent or subsequent courses in
signals and systems, electro-magnetic theory, control engineering, communication
engineering, system modeling, optics and quantum physics. This course mainly focused on
the applications of mathematical concepts in various engineering problems related to
electrical and electronics circuit analysis, digital signal processing, vibration analysis, walled
shell theory, wave propagation and spectral analysis. Complex integration and power series
expansions are also presented with applications.
PREREQUISITES:
Requires basic knowledge of mathematical concepts
COURSE OBJECTIVES:
Student will be able to
1. Identify Laplace and inverse Laplace transforms with applications.
2. Illustrate Fourier series expansion
3. Compute vector differentiation and integration
4. Evaluate complex integration and applications
5. Calculate residues and contour integration
COURSE OUTCOMES:
At the end of the course, students will develop ability to
1. Explain Laplace transforms to solve differential equations
2. Decide Laplace transform technique to engineering problems
3. Recommend vector calculus to different engineering problems
4. Discuss analytical functions apply to velocity potentials, stream functions and orthogonal
trajectories
5. Create complex integration to solve real improper integrals
6. Apply Fourier series to engineering problems
7. Analyze vector integral theorems
8. Judge in evaluation of contour integration
Unit-I : Laplace Transforms

Definition – Existence – Laplace transforms of standard functions – First & Second Shifting
theorems – Change of scale property – Laplace transform of Derivatives – Integrals-functions
multiplied by t – divided by t – Laplace Transform of Periodic functions. Inverse Laplace
transforms – Inverse Laplace transforms by partial fractions – Inverse Laplace transforms of
Derivatives – Integrals – functions multiplied by s – divided by s – Convolution theorem –
Applications of Laplace transforms to Ordinary Differential Equations.
Unit-II: Fourier Series
Definition of Fourier series – Dirichlet conditions – Fourier series of functions defined in [0,
2π] – Fourier series of Even and Odd functions – Half range Fourier sine and cosine series –
Fourier series in arbitrary intervals.
Unit-III : Vector Calculus

Vector Differentiation: Introduction to vectors - Ordinary and Partial derivatives of a vector
valued function – Gradient of a scalar function – Divergence and Curl of a vector function –
vector Identities (without proofs).
Vector Integration: Integral of a vector valued function – Line integrals – Surface integrals
– Volume integrals – Vector Integral Theorems – Green‟s theorem-Stokes theorem – Gauss
Divergence theorems (statements without proofs) – verification & Applications.
Unit-IV: Complex Analysis - 1

Functions of Complex Variables: Analyticity-properties-Cauchy-Riemann conditions-
harmonic and conjugate harmonic functions.
Complex Integration and Power Series: Line integral – evaluation along a path and by
indefinite integration – Cauchy‟s integral theorem – Cauchy‟s integral formula – Generalized
integral formula – applications. Radius of convergence - Expansion in Taylor‟s series –
Maclaurin‟s series – Laurent series – applications. Definitions - Singular point – Isolated
singular point – pole of order m – essential singularity
Unit-V: Complex Analysis - 2

Contour Integration: Residues – Evaluation of residues by formulae – Residue theorem
(proof) – Evaluation of integrals of the type
 

c  2
e
imx
a) f ( x)dx b) c) f ( x)dx

 f (cos , sin  )d
c 
TEXTBOOKS:
1. Erwin kreyszig, "Advanced Engineering Mathematics", John wiley and sons, 605 Third
Evenue, New York.
2. Peter V. O'Neil, "Advanced Engineering Mathematics", Cl-Engineering, March 2006.
REFERENCE BOOKS:
1. R. K. Jain, S.R.K. Iyengar, “Advanced Engineering Mathematics", Narosa publishing
house, New Delhi.
2. B. S. Grewal, "Higher Engineering Mathematics", Khanna publishers, Delhi.
3. Sri Ramachary S.K, “Engineering Mathematics-II”, BSP.
4. Ramana B.V, Engineering Mathamatics”, Tata McGraw Hill.
Content Beyond Syllabus:

Applications of Fourier series analysis to second order partial differential equations.
LECTURE PLAN
Suggested book
Modules and sub Lecture (Adv. Engg. Math.
S. No. Topics in syllabus
modules No. By Erwin Kreyszig)
with page numbers
Unit-I Laplace Transforms (No. of Lectures: 19)
Definition and Laplace
1 Introduction transforms of standard L1 251
functions
Finding Laplace
2 Problems Transform of given L2 257
functions
First & Second Shifting First & Second Shifting
3 theorems in Laplace theorems in Laplace L3 253, 265
transform transform
Change of scale L4
Change of scale property in
4 property in Laplace 266
Laplace transform
transform
Laplace transform of L5
Laplace transform of
5 Derivatives & L6 258, 262
Derivatives & Integrals
Integrals
Laplace transform of Laplace transform of L7
6 functions multiplied by t & functions multiplied by L8 275, 276
divided by t t & divided by t
Laplace transform of Laplace transform of L9
7 265
Periodic functions Periodic functions
Introduction to inverse Introduction to inverse L10
8 Laplace transform & Laplace transform & 251, 257
problems problems
First & Second Shifting First & Second Shifting L11
9 theorems in inverse theorems in inverse 253, 265
Laplace transform Laplace transform
Change of scale L12
Change of scale property in
10 property in inverse 267
inverse Laplace transform
Laplace transform
Inverse Laplace L13
Inverse Laplace transforms transforms of L14
11 275, 276
of Derivatives & Integrals Derivatives &
Integrals
Inverse Laplace L15
Inverse Laplace transforms
transforms of functions L16
12 of functions multiplied by s 258, 262
multiplied by s &
& divided by s
divided by s
Convolution theorem (with Convolution theorem L17
13 279
out proof ) (with out proof )
Applications of Laplace Applications of L18
14 transforms to Ordinary Laplace transforms to L19 260
Differential Equations Ordinary Differential
Equations
Unit-II Fourier Series (No. of Lectures: 10)
Definition of Fourier L20
Definition of Fourier series
15 series and Dirichlet 529
and Dirichlet conditions
conditions
Fourier series of L21
Fourier series of functions
16 functions defined in [C, L22 532
defined in [C, C+2π]
C+2π]
Fourier series of even and Fourier series of even L23
17 541
odd functions and odd functions L24
Half range Fourier Sine Half range Fourier Sine L25
18 544
and Cosine series and Cosine series L26
Fourier series in L27
Fourier series in arbitrary
19 arbitrary intervals [C, 537
intervals [C, C+2L]
C+2L]
Fourier series of even L28
Fourier series of even and
20 and odd functions in [0, 541
odd functions in [0, 2L]
2L]
Half range Fourier – L29
Half range Fourier – Sine
21 Sine and Cosine series 544
and Cosine series in [0,L]
in [0,L]
Unit-III Vector Calculus (No. of Lectures: 15)
Vector Differentiation
Introduction to vector Introduction to vector L30
21 423
differentiation differentiation
Gradient of a scalar Gradient of a scalar L31
22 446
function function
Divergence of vector Divergence of vector L32
23 453
function function
Curl of a vector L33
24 Curl of a vector function 457
function
Vector identities (without Vector identities L34
25 463
proofs) (without proofs)
Vector Integration
Introduction to Vector Introduction to Vector L35
26 464
Integration Integration
27 Line integrals Line integrals L36 464
28 Surface integrals Surface integrals L37 496
29 Volume integrals Volume integrals L38 505
Vector Integral Theorems – Vector Integral L39
30 Green‟s theorem and Theorems – Green‟s L40 485
problems theorem and problems
Stokes theorem and Stokes theorem and L41
31 516
problems problems L42
32 Gauss Divergence theorem Gauss Divergence L43 506
and problems theorem and problems L44
UNIT-IV Complex Analysis – I (No. of Lectures: 17)

Functions of Complex Variables
Continuity, Continuity, L45
33 665, 666
Differentiability Differentiability
Analytic function – Analytic function – L46
34 667
properties properties
Cauchy – Riemann Cauchy – Riemann L47
35 669, 671
conditions, problems conditions, problems
36 Max.Min principle Max.Min principle L48 673
Harmonic function – Harmonic function – L49
37 672
conjugate conjugate
Milne – Thompson L50
38 Milne – Thompson method 674
method
Complex Integration and Power Series
39 Line integral Line integral L51 704
Cauchy integral theorem Cauchy integral L52
40 713, 714
and problems theorem and problems L53
Cauchy integral L54
Cauchy integral formula,
41 formula, generalization, L55 722, 723
generalization, problems
problems
Radius of convergence, Radius of convergence, L56
42 Taylor‟s, Maclaurin‟s Taylor‟s, Maclaurin‟s L57 743, 751
series expansion series expansion
Laurent series, L58
43 Laurent series, problems 770, 775
problems L59
Types of singularities, Types of singularities, L60
44 776, 780
UNIT – V Complex Analysis – II (No. of Lectures: 06)
L62
45 Residue – Evaluation Residue – Evaluation 781, 786
L63
Residue Theorem – Residue Theorem – L64
46 784, 786
Evaluations of L66
Evaluations of improper
47 improper real integrals L67 787
real integrals (4 types)
(4 types)
Review Questions
1.1 Find the Laplace transform of Sin2t Cos3t and e-3t Cos4t.
1.2 Find the Laplace transforms of t2 + at + b
1.3 Find the Laplace transforms of cos(ωt+θ)
1.4 Find the Laplace transforms of sin2t.
1.5 Find the Laplace transforms of
f(x) = 1, 0<t<2
= 2, 2<t<4
= 3, 4<t<6
= 0, t>6
1.6 Find L [t 2 e 2t S int]
1.7 Find L [te 3t Sin 2t ]
d n __
1.8 Show that L{t f(t)}=(-1) do n f ( s) where n=1, 43……..
n n
1  __ a
1.9 Show that L  f (t )   f (0)ds .
t  0
2 -2t
1.10 Find L{t e }
1.11 Find L{eat sin h bt}
1.12 Find L{eat cos h bt}
1.13 Find L{e-at sin h bt}

t
1.14 Find L {e-4t t sin 3t dt }
0
1.15 Find the Laplace Transform of the function: t e−t sin2t.

1.16 Find the Laplace transform of e2t + 4t3 – 2 sin3t + 3cos3t.
1.17 Evaluate L{et (cos2t + 1/2 sinh2t)}
1.18 Find Laplace transform of sin(at+b).
cos t , 0  t  
1.19 Find LT of f (t )  
sin t , t  
1.20 Find LT of te 4t sin 3t .
1.21 Solve the differential equation: y′′ - 4y′ + 3y = 4e3x, y (0) = - 1, y′(0) = 3
1
1.22 Find inverse Laplace transform of
( s  1)( s  2)
1
1.23 Find inverse Laplace transform of by convolution theorem.
s( s  a 2 )
2
4
1.24 Find the inverse Laplace transforms of
(s  1 )(s  2 )
s3
1.25 Find L-1 [ ]
( s  6n  13) 2
2
s3
1.26 Find L-1 [ ]
s  10n  29
2
 1 
1.27 Find L-1  s 2 ( s  2) 
 
 s 3  3s 2  6  4 
1.28 Find L1  2 2 
 ( s  2s  2) 
2s  1
1.29 Find Inverse Laplace Transform of
s  12 s  22
2s
1.30 Find Inverse Laplace Transform of
4  s4
1
1.31 Find the inverse Laplace transforms of
 s  25
2
d2y dy
1.32 Solve the differential equation 2  2  5 y  et sin t where
dt dt
1
y(0) = 0, y (0) = 1 by using Laplace transform.
1.33 Solve the following initial value problem by using Laplace transform :
4y" + π2y =0, y(0)=2, y'(0) =0.
1.34 Using Laplace transform, solve y′′+2y′+5y = e-t Sin (t), given that y(0) = 0, y′(0) =
1.
1.35 Solve  D4  2D2  1 y  0, y  0, y '  1, y ''  2, y '''  3 at t=0.
2.1 Find the value of function in the Fourier series for f(x) = e-ax in (-, ).
2.2 Express f(x) = x2 in (0, ) as half range cosine series.
2.3 Find the half range sine series for
 
 sin x, 0  x  4
f ( x)  
 
cos x, x
 4 2
2.4 Find „a0‟ term in the Fourier expansion of the function f x  

1
12
 
3x 2  6 x  2 2 .
2.5 Write the Dirichelet conditions of Fourier series.

2.6 Express f(x) = x2 as a Fourier series in [-l, l].
2.7 Obtain a half range cosine series for
 L
 kx 0 x

f x    2
k L  x  L
xL

 2
1 1 1
Deduce the sum of the series 2
 2  2  ........
1 3 5
2.8 Expand the function f(x) = xsinx as a Fourier series in the interval    x   .
2.9 Expand the function f(x) = xcosx as a Fourier series in the interval    x   .
2.10 Find half range sine series for f(x)= x 2 in (0,  )
x
2.11 Obtain Fourier series expansion f(x) =x cos in the interval –L < x < L.
L
3.1 Find the directional derivative of the scalar point function φ (x, y, z ) = 4xy2 +2x2yz at
the point A(1, 2, 3) in the direction of the line AB where B = (5,0,4).
3.2 If 1  x 2 y and  2  xz  y 2 find   (1   2 )
3.3 Find constants a, b, c so that the vector A =(x+2y+az) i +(b x–3y–z)j+(4x+cy+2z)k is
irrotational. Also find ϕ such that A = φ .
3.4 Find a and b such that the surfaces ax2 – b y z=(a + 2)x and 4ax2y + z3=4 cut
orthogonally at (1, -1, 2).
3.5 Show that F = (2xy + z3) i + x2 j + 3 x z2 k is a conservative force field. Find the
scalar potential and the work done by F in moving an object in this field from (1, –2,
1) to (3, 1, 4).
3.6 For any vector A, find div curl A.
3.7 Evaluate   A.nds
s
where A=z i +x j-3y2z k and S is the surface of the cylinder
2 2
x + y = 16 included in the first octant between z=0 and z=5.
3.8 If φ = 2xy2z +x2y, evaluate   dr where C consists of the straight lines from (0, 0, 0)
c
to (1, 0, 0) then to (1, 1, 0) and then to (1, 1, 1).

3.9 Evaluate 2 log r where r  x 2  y 2  z 2
3.10 If F = (x2 − 27) i−6yzj +8xz2k evaluate  F .d r
c
from the point (0,0,0) to the point
(1,1,1) along the straight line from (0,0,0) to (1,0,1), (1,0,0) to (1,1,0) and (1,1,0) to
(1,1,1).
3.11 If A is irrotational vector, evaluate div(A x r) where r = x i +y j +z k.
3.12 If F= x y i – z j + x2k and c is the curve x = t2, y = 2t, z = t3 from t=0 to t=1.
Evaluate  F . dr.
c
3.13 Find the directional derivative of φ (x, y, z) = x2yz + 4xz2 at the point (1, -2, -1) in the
direction of the normal to the surface f(x, y, z) = x log z –y2 at (-1, 2,-1).
3.14 Find the work done in moving a particle in the force field F=3x 2i + j + z k along the
straight line from (0, 0, 0) to (2, 1, 3).
3.15 Find the work done by F = (2x−y − z) i + (x +y − z) j + (3x −2y −5z) k along a curve
C in the xy plane given by x2 + y2 = 9, z = 0.
3. 16 Find the angle between the surfaces x2+y2+ z2=9 and z=x2 + y2 − 3 at the point
(2, -1, 2)
3.17 Evaluate  F.dr
c
where F=(x-3y)i+(y-2x)j and c is the closed curve in the xy-plane,
x=2cost,y=3sint , from t=0 to t=2π.

3.18 Find the work done in moving a particle in the force field F=3x 2i + j + z k along the
3.19 For any vector A, find div curl A.
3.20 Evaluate  A.n ds
s
where A=z i +x j-3y2z k and s is the surface of the cylinder
2 2
x + y = 16 included in the first octant between z=0 and z=5.
3.21 Find the work done in moving a particle in the force field F=3x 2i + (2xz − y)j + z k
along the straight line from (0, 0, 0) to (2, 1, 3).
3.22 Find the angle between the surfaces x2+y2+z2=9 and z=x2 + y2 − 3 at the point
(2, -1, 2)
3.23 Show that F=(2xy +z3)i+x2j +3xz2k is a conservative force field. Find the scalar
potential. Find the work done in moving an object in this field from (1, -2, 1) to (3, 1,
4).
3.25 Find the work done in moving a particle in the force field F = 3x2 i + (2xz − y) j + z
k along the curve x2 = 4y, 3x3 = 8z from x = 0 to x = 2.
3.26 Evaluate   A.n ds where A=18zi-12j+3yk and s is that part of the plane
s
2x+3y +6z=12 which is located in the first octant.

3.27 Find the directional derivative of  = x2yz+4xz2 at (1, -2, -1) in the direction 2i–j-2k.
3.28 Find the work done in moving a particle in the force field F=3x2i + (2xz ¡ y)j + z k
along the space curve x = 2t2; y = t; z = 4t2 - t from t=0 to t=1.
Find grad  where   (x 2  y 2  z 2 ) e- x  y  z
2 2 2
3.29
3.30 Find the angle between the surfaces x2+y2+ z2= 4 , z =x2 + y2 + 3 at the point (2, -1, 1).
3.31 Find A .  at (1, -1, 1) if A = 3xyz 2 i  2 xy 3 j  x 2 yzk and  = 3x 2  yz
3.32 Show that F= (2 xy  z 3 )i  x 2 j  3xz 2 k is a conservative force field. Find the scalar
potential. Find the work done in moving an object in this field from (1,-2,1) to (3,1,4).
3.33 Find a unit normal vector to the surface x3 + y3 + 3xyz = 3 at the point (1, -2, -1)
3.34 In what direction from (3,1,-2) is the directional derivative of f = x2y2z4 maximum ?
Find also the magnitude of maximum.
3.35 Find constants a & b so that surface ax2 –b y z = (a+2)x will be orthogonal to the
surface4x2y+z3 = 4 at the point (1,-1,2).
3.36 If F = (x-y)i + (x+y)j evaluate line integral of F. dr around curve c consisting of y =x 2
and y2 = x
3.37 Evaluate ∫∫ex dy dz – y ex dz dx –3zdxdy over the surface of the cylinder x2 + y2 = c2 ,
0 ≤z ≤b
3.38 Find the directional derivative of xy2 + yz3 at the points (2,-1,1) in the direction of
vector i+2j+2k
3.39 Find angle between x2+y2+z2=4 and z=x2+y2+3 at (2, -1, 1)
3.40 Find the work done by moving a particle in the force field. E= 3x2i+(2xz-y)j+ z k along
the curve x=2t2, y=t, z=4t2-t from t=0 to t=1
3.41 Find the directional derivative of  = x2yz + 4xz2 at (1,-2, -1) in the direction of 2i-j-2k
3.42 Find the directional derivative of xyz at (1,1,1) in the direction of the vector i+j+k.
3.43 If f  e x y  z (i  j  k ) .find curl f .
3.44 F  yi  zj  xk find the circulation of F round the curve c ,where c is the circle
x 2  y 2  1, z  0
3.45 If F = 2xyi+yzj+xzk find the surface integral over the parallelopiped x=0, y=0, z=0,
x=2, y=1, z=3.
3.46 Evaluate  Fdv when
v
F  xi  yj  zk and V is the region bounded by
x=0,y=0.z=4,z= x 2
3.47 Using Divergence theorem, evaluate  (xdydz  ydzdx  zdxdy),where, S is the
S
2 2 2 2
sphere x + y + z = a .
3.48 Verify divergence theorem for f = 4xi – 2y2j + z2k the region bound by x2 + y2= 4,
z= 0 and z =1
3.49 Verify Gauss divergence theorem for the function F  y i  x j  z 2 k over the
cylindrical
region bounded by x2 + y2 = 9, Z = 0, Z = 2.
3.50 If A  2 x 2i  3 yzj  xz 2 k and f = 2z - x3y then find A.f at (1, -1, 1).
3.51 Evaluate line integral  ( y 2 dx  x 2 dy ) about the triangle whose vertices are (1, 0), (0,1)
C
and (-1, 0).

3.52 Find the work done in moving a particle in the Force field F  3x 2i  j  2k along the
3.53 Verify Green‟s theorem in the plane for  x   
 xy 3 dx  y 2  2 xy dy . Where c is a
2
square with vertices (0, 0), (2, 0), (2, 2), (0, 2).
3.54 Verify divergence theorem for F  4 xi  2 y 2 j  z 2 k taken over the region bounded by
the cylinder x 2  y 2  4, z  0 and z 3
3.55 State Green‟s theorem in plane.
3.56 State Gauss divergence theorem.
3.57 State Stokes‟ divergence theorem
3.58 Verify divergence theorem for F  4 xi  2 y 2 j  z 2 k taken over the region bounded by
the cylinder x 2  y 2  4, z  0 and z 3
3.59 If A  ( x  y)c  ( x  y) j Evaluate  A. d r
C
around the curve C consisting of y = x2 and
2
y = x.
3.60 Verify Green‟s theorem in plane for  (x  2 xy )dx  ( x 2 y  3)dy where C is the
2
c
2
boundary of the region defined by y =8x and x=2.
4.1 Write down the CR-equations in polar form.
dz
4.2 Evaluate 
C
z
where C:|Z|=1.
4.3 Expand sinz as Taylor‟s series about Z = /4 upto the first three terms.
 2 2 
4.4 If f z  is a regular function of z then show that  2
   f z   4 f ' z  .
2 2
2 
 x y 
4.5 Define Harmonic function.
4.6 Show that z3 is analytic for all z.
4.7 State Cauchy‟s integral theorem.
What is the nature of singular point in f z  
sin z
4.8 .
z
4.9 State Taylor‟s theorem.
4.10 State Laurent‟s theorem.
4.11 Obtain the Taylor‟s expansion of e1+z in powers of (z-1).
2z 2  3
4.12 Evaluate 
C
z3
dz over c: |z|=1.
4.13 Show that the function f z   z is continuous over C.

4.14 Show that xy 2 cannot be the real part of an analytic function.
4.15 Define a singular point and an isolated singular point with an example of each.
4.16 Show that f ( z ) | z | is not differentiable anywhere.
4.17 Determine constants a and b such that u  ax3  by3 is harmonic function.
log z 1
4.18 Find  ( z  2)
c
2
dz , where C is z 
2
.
4.19 Find the singular point(s) of the function f ( z )  z 2 e1/ z
4.20 Find Taylor expansion of f(z) = 1/z about z = 1.
4.21 Determine the analytic function whose real part is e2x(xcos2y – ysin2y).
4.22 Prove that the function f(z) = sinhz is analytic.
dz
4.23 Evaluate  z
C
2

1 z2  4
, C:|Z|=1.5 using Cauchy‟s integral formula.

1
4.24 Explain f(z) = in a Laurent series valid for 0 < |z – 2| < 1.
1  z 2  z 
4.25 If u = ex(cosy - siny) where w = u + iv is an analytic function, find the function w.
4.26 Show that the real part of analytic function f(z) is Harmonic, if f(z) = u + iv is an
 2  2 
analytic function, show that  2  Re al f z   2 f z  .
2 2
2 
 x y 
4.27 Verify Cauchy‟s integral theorem for f(z) = z2 for a curve OAB where OA is given by
y = 0, AB is given by x + y = 1 and BO is given by x = 0.
 y  x  3x i dz where C consists of the line segments from z  0 to

2
4.28 Evaluate
C
z  i and the other from z  i to z  1  i .

Sin2 x
4.29 Find an analytic function whose real part .
Cosh2 y  Cos 2 x
e2 z
4.30 Evaluate C ( z  1)4 dz , C : z-1 = 3.
4.31 Integrate f ( z )  x 2  i x y from A(1, 1) to B(2, 8) along the (a) the straight line AB,
(b) the curve C: x  t , y  t 3 .
1
4.32 Give two Laurent's series expansion in power of z for f ( z )  and specify
z (1  z )
2
the regions in which these expansions are valid.
Find the residue for f z  

sin z
5.1 at z = 1.
z  12
z3
5.2. Evaluate the residue of f ( z )  2 .
( z  1)
5.3 Define the terms residue and improper integrals with suitable examples.
z2
5.4 Determine the poles of the function f z   and the residues at each pole.
z  12 z  2
 z 
sin  
 2 
Determine the poles of the function f z  
 
5.5 and the residue at each pole.
z  12 z 2  1

dx
5.6 Evaluate  1 x

4
by using Residue theorem.
 z 
sin  
 2 
Determine the poles of the function f z  
 
5.7 and the residue at each pole.
z  12 z 2  1
3z  1
2
Find the residue at z = 1 of the function f z  
z  12 z 2  1
5.8 .

d
5.9 Evaluate  2  3 cos .
0
2
d
5.10 Evaluate  a  b cos , 0  b  a  using complex integration.
0
(EE135) NETWORK ANALYSIS
Hours / Week Marks

Year Semester C
II I 4 1 - 4 30 70 100
Course Description:-
The goal of this course is to explain in various concepts of the analysis of DC circuits
as well as the basic concepts of the AC circuit.
In this course emphasis will be given to the concept of voltage, current, power and
energy. You will be learn the voltage current relationship of the basic circuit elements like
resistor, inductor and capacitor, dependent and independent sources, apply Kirchhoff‟s
current and voltage law to the circuit in order to determine voltage, current, power in any
branches of the circuit excited by DC voltage and current sources. Apply simplifying
techniques like star delta transformation, nodal analysis mesh analysis and theorems to solve
circuits easily.
The goal also included the transient response of the circuit to sinusoidal excitation in
time domain, application of phase to circuit analysis, detailed study of graph theory, magnetic
coupled circuits where you will be familiar with mutual induction, resonance, bandwidth,
quality factor, resonance frequency.
COURSE OBJECTIVES:
Student will be able to
1. Learn the passive components and their V-I relations.
2. Learn electric circuit laws and network theorems with D.C. and A.C. excitations and solve
electric circuits.
3. Calculate A.C. quantities and draw phasor diagrams.
4. Understand the concepts of transient response and solve problems.
5. Learn basic theorems, two port network and apply them.
COURSE OUTCOMES:
At the end of the course, the student will develop ability to
1. Solve electric network with passive elements
2. Represent the network solution in a graphical form by means of phasor and locus diagrams
3. Analysis transient response of different circuit and two port network
4. Apply network theorem to different electric network.
5. Solve a complex circuit by applying reduction technique like star-delta, theorems etc.
6. Understand the concept of resonance, band width and quality factor.
7. Find average and RMS value for the different periodic signals.
8. Solve first and second order differential equation related problem using Laplace transform.
UNIT – I
Introduction to Electrical Circuits : Circuit Concept – R-L-C Parameters- Voltage and
Current sources – Independent and dependent sources – Source transformation – Voltage –
Current relationship for passive. Kirchhoff‟s laws – network reduction techniques – series,
parallel, star-to-delta or delta-to-star transformation. Nodal analysis Mesh analysis Super
node and Super mesh for DC excitations.
UNIT – II
Single Phase AC Circuits: Single Phase A.C Circuits: R.M.S and Average values and form
factor for different periodic wave forms, Steady state analysis of R, L and C (in series,
parallel and series parallel combinations) with sinusoidal excitation – Concept of Reactance,
Impedance, Susceptance and Admittance – Phase and Phase difference – concept of power
factor, Real and Reactive powers, Complex power. : Resonance – series, parallel circuits,
concept of band width and Q factor.
UNIT – III
Network Theorems with DC and AC Excitations: Superposition, Reciprocity, Thevenin‟s,
Norton‟s, Maximum Power Transfer and Compensation theorems for dc and ac excitations.
RA15 B.Tech. ECE Syllabus
SR Engineering College (Autonomous), Warangal, Telangana Page 40 of 197
UNIT – IV
Transient Analysis: Transient Response of RL, RC Series, RLC Circuits (First and Second
Order Circuits), for DC Excitations, Initial conditions, Solution Using Differential Equations
Approach and Laplace Transform Method.
UNIT – V
Two Port Networks: Impedance Parameters, Admittance Parameters, Hybrid Parameters,
Transmission (ABCD) Parameters, Conversion of one parameter to another, Conditions for
reciprocity and symmetry, Interconnection of Two Port Networks in Series, Parallel and
Cascaded Configurations, Image Parameters, Illustrative Problems
TEXT BOOKS:
1. William Hayt and Jack E. Kimmerly, “Engineering Circuit Analysis”, McGraw Hill
Company, 6th Edition.
2. A. Chakrabarthi, “Circuit Theory: Analysis and Synthesis”, Dhanpat Rai and Co., 6th
Edition.
REFERENCE BOOKS:
1. Vanvalkenburg, “Network Analysis”, PHI.
2. N C Jagan and C. Lakshminarayana, “Network Theory”, B.S Publications.
LECTURE PLAN
Suggested books
with Page Nos.
Sl. Lecture (A. Chakrabarthi,
Topics in syllabus Modules and Sub modules
No. No. “Circuit Theory:
Analysis and
Synthesis”,)
UNIT – I (No. of Lectures – 15)
Introduction to L1
1 Circuits concepts 1
electrical circuits
L2
2 R-L-C parameters Properties of R-L-C parameters 5,6,7
L3
Voltage and current Voltage-current relationship for L4
3 5,6,7
sources passive elements
L5
4 Energy sources Dependent &independent sources L6 9,10,11
Kirchhoff‟s current
5 Problems L7 16,17,18
law definition
6 Kirchhoff‟s voltage
Problems L8 11,12,13
law definition
L9
Nodal analysis& problems. 76,77,78,81,82
7 L10
super node analysis
Mesh analysis
L11
8 &super mesh Problems 68,69,70,74,75
L12
analysis
REFER
9 Series-parallel ,star to delta and
Network Reduction L13 CHAKRABARTI
delta to star transformation
techniques L14 4,8,9,10,20,21,22,23,
problems
24
Source
10 transformation Problems L15 83,84,85
techniques
UNIT –II (No. of Lectures – 13)
11 Introduction to
L16
single phase Difference b/w A.C and D.C 169,171
voltage source
R.M.S and Average Problems on different periodic L17 172,173,174,175 upto
12
values Form factor waveforms L18 186
Steady state Series, parallel and series parallel L19
combinations with sinusoidal Refer chakrabarthi
13 analysis of R-L-C L20
excitation 201-246
Concept of Refer sudhkar
14 reactance Susceptance ,admittance L21 shamohan
impedance s 192,193,upto 205
Concept of power
factor, Real and L22 Refer Chakrabarti
15 problems
reactive powers, 305-329
complex power
Definition of Problems on Series, parallel L23 Refer Chakrabarthi
16
Resonance circuits L24 247-248
Concept of band L25 Refer Chakrabarti
17 Problems
width and Q factor L26 249-250
L27
18 problems Of all topics L28 Refer both books
UNIT –III (No. of Lectures – 13)
L29
Introduction to Classification of network Refer chakrabarti
19
network theorems theorems 99
Problems on Thevenins theorem L30
20 Thevenins theorem 99-200
with DC and AC exitation L31
Problems on Superposition L32
Superposition
21 theorem with DC and AC L33 121
theorem
exitation
Problems on Nortons theorem L34
22 Nortons theorem 111
with DC and AC exitation L35
Reciprocity Problems on Reciprocity theorem L36
23 133
theorem with DC and AC exitation L37
Problems on Maximum power
Maximum power L38
24 theorem with DC and AC 127
theorem L39
exitation
L40
25 problems Of all topics L41 Refer both books
UNIT-IV (No. of Lectures – 11)

Introduction to Classification of transient Refer chakrabarti
26 L42
Transient analysis analysis 331
Problems on RL circuit first&
Transient response L43
27 second order system for DC 333
of RL circuit L44
excitations
Problems on RC circuit first&
of RC circuit L46
excitations
Problems on RLC circuit first&
of RLC circuit L48
excitations
Solution using
30 Differential equation problems L49 Refer van valkenburg
approach method
Solution using L50
31 Laplace Transform problems L51 377-430
approach method L52
UNIT –V (No. of Lectures – 14)
Introduction to two Classification of two port Refer chakrabarti
35 L53
port networks networks 485
Impedance Problems on impedance L54
36 492
parameters parameters L55
Admittance Problems on admittance L56
37 500
parameters parameters L57
L58
38 Hybrid parameters Problems on hybrid parameters 504
L59
ABCD or
L60
39 Transmission Problems on ABCD parameters 507
L61
parameters
Conversion of one Interconnection of Two port
L62
40 parameter to anther networks in series ,parallel and 517-525
L63
parameter cascaded configurations
L64
Illustrative problems condition
41 Image parameters L65 508
for reciprocity and symmetry
L66
Review Questions
UNIT I
1. Calculate io using super mesh analysis.
2. Find Vx using source transformation theorem.
3. (a) How basic elements are classified in electrical engineering? write about properties
of any two passive elements.
(b) For the circuit shown in fig.1, find power delivered by the source.
4. (a) Derive an expression for equivalent capacitance for two capacitors connected in
series.
(b) Using nodal analysis find power loss in all resistors shown in fig. 2
5. For the circuit shown in fig.3, using star- delta reduction method, find power delivered by
the
Source.
6 (a) Derive an expression for energy stored in capacitor when applied with voltage of V
volts.
(b) Explain the types of dependent and independent source with neat diagram.
7. Determine the resistance between the terminals A&B and hence find the current through
the voltage source. Refer figure 4
8. Determine the current the following circuits with reference to the indicated
Direction, also calculate voltage drops across . Where =10Ω
= 40V.
9. Calculate the amount of current flowing through voltage source and voltage drop across
100Ω resistance using mesh analysis.
10.(a) Calculate the voltage using nodal analysis technique, also calculate the
amount
Of current flowing through 4 ohm resistance.
(b) Calculate the nodal voltage using node analysis method

UNIT II
11. Define peak to peak value and RMS value of an alternating wave.
12. Calculate average and rms values of the following waveform.
13. For the waveform shown in fig.5 find r.m.s and average values.
14. A certain electrical circuit results a passing current of i = 6.1 sin (377t+300)A when it is
Applied with voltage of v=340 cos (377t-500)V. Find the circuit elements and real and
Reactive power.
15. Find the value of unknown resistance (Rc) value that the circuit in fig.6 gets resonance
Condition.
16. A parallel resonance network consisting of a resistor of 60Ω, a capacitor of 120uF and an
Inductor of 200mH is connected across a sinusoidal supply voltage which has a constant
output
Of 100 volts at all Frequencies. Calculate, the resonant frequency, the quality factor and the
Bandwidth of the circuit, and the circuit current at resonance.
17. A parallel AC circuit draws 8 amps of current through a purely resistive branch and 14
amps
Of current through a purely inductive branch, Calculate the total current and the angle Θ of
the
Total current, explaining your trigonometric method(s) of solution.
18. A parallel AC circuit draws 100 mA of current through a purely resistive branch and 85
mA
Of current through a purely capacitive branch, Calculate the total current and the angle Θ of
the
Total current, explaining your trigonometric method(s) of solution.
19. (a) If a sinusoidal voltage is applied to an impedance with a phase angle of , draw the
Resulting voltage and current waveforms.
(b) Define reactive power, in contrast to “true” or “apparent” power.
20. Find the value total current is flowing through the source, also find the current flowing
Through inductor, capacitor, and resistor individually.
UNIT III
21. For circuit shown in fig.7 find the value of load impedance for maximum power transfer.
22. Obtain the Thevenin‟s equivalent of the following circuit.
23. Using superposition theorem find Io.
24. Using superposition theorem find the value of current flowing through 2 ohm resistance.
25. Using maximum power theorems find the power absorb by load resistance.
26. What do you mean by compensation theorem, explain with an example.
27. Write down the procedure to solve thevenin‟s theorem for both dependent and
independent
Source, explain with suitable examples.
28. Prove that the efficiency is 50 % during maximum power transfer theorem.
UNIT IV
29. Find the voltage, Vc(t), over the capacitor for all time t>0
30. The voltage source Vs in the circuit shown below is nominally 5V. A power surge
At Time t=0 causes it to instantaneously jump to 10V, and then at time t=5ms, it
Instantaneously drops back to 5V. Express the current flowing down through the 30
Ohm resistor (as a function of time)
31. The voltage supply in the circuit shown below is switched on at time 0. Compute the
voltage over the 3K ohm resistor for all time.
32. Assume that the switch S is in position 1 for a long time and thrown to position 2 at t=0.
At t = 0+, find the value of current i1.
33. In the following circuit, the switch S is closed at t = 0. The rate of change of current
di(0+)/dt
is ?.
34. In the circuit shown, switch SW is closed at t =0. Assuming zero initial conditions, the
value
of Vc(t) (in volts) at t = 1 sec is ?
35. Find the time domain current i(t) if its Laplace transform is
I(S) =
36. Find the Laplace transform of where a is constant.
37. Find the inverse Laplace of the following function.
(a) (b)
UNIT V
38. Determine the impedance and admittance parameter as the circuit given below.
39. Find the Z parameters of the two port network as shown in figure given below.
40. Transform Z-parameters in terms of ABCD and Y- parameters.

41. What do you mean by interconnection of two port network, derive the expression for
Cascaded And parallel connection.
42. Find the Y-parameters and ABCD parameters of the two-port network as shown in figure
Given below
43. Transform h-parameters in terms of ABCD, admittance and impedance parameters, write
Down the symmetrical and reciprocal condition of ABCD and h-parameters.
44. Find the Z-parameter in the circuit given below.
45. Two port network N as shown in figure is specified by

Find and
46. Express reciprocity and symmetry criteria for impedance, admittance, hybrid and
Transmission line parameters, also explain why Z parameters is called as open circuit and Y-
Parameters are called as short circuit parameters.
47. Derive the expression of interconnected two port network of series connections.
Short Questions (NA)
1. Three resistors of 1  each are connected in star form. Find equivalent resistance in
delta connection.
2. What is meant by a periodic waveform? Draw any two shapes.
3. A voltage of 100V dc is applied across two series connected capacitors of 100
F and 25 F . Find voltage drop across each capacitor?
4. A 750  resistor is in series with a 0.1 F capacitor. Find the frequency, if the total
impedance of the circuit is 1000  If a voltage of V=80Sin (314t+600) V is applied
to a load of Z= (43+j25)  find power factor.
5. Two coils of inductance s 2H and 1H with flux aiding are connected in series. The
mutual inductance is 0.5H find total inductance of the combination.
6. What is the power factor a series RLC circuit operating at resonance condition?
7. For a certain network have seven node and five independent loops. Find the
number of branches.
8. State Norton's theorem
9 . Draw the symbols of dependent sources.
10 .Define form factor and crest factor.

11. Derive the expression for resonant frequency of a RLC series circuit
12. For what value of RL maximum power will be transferred?
13. State reciprocity theorem

19.
14. A battery provides 6 V on open circuit and it provides 5.4 V when delivering 6 A. Find
the internal resistance of the battery?
15. Five inductors are connected in series with lowest value is 5H. if the value of each
inductor is twice that of preceding one and if the inductors are connected in order
ascending value. Find the total inductance.
16. For the circuit shown below if I1 = 5A, I2= 15A and I3=7A find IT.
17. A 750
18. If a voltage of V=80 Sin(314t+600

power.
19. Define reciprocity theorem.
20 Define form factor.
21. Define RESONANCE,BANDWIDTH& Q-FACTOR.
22 Write the time period relations for RL &RC transient anylasis.
23 define two port network
24 define Laplace transform
25. define symmetry and reciprocity in two port network
26 write symmetry and reciprocity conditions for all two port networks
27 write the relations for all parameters for two port network.
28 write some applications for Laplace transform
29 draw and write relations for star and delta connection
30 define resistance, conductance ,resistivity & conductivity.
31 draw the symbols for voltage and current sources.
32 define linear and nonlinear circuit.
33 define filter
34 define attenuator.
(EC103) ELECTRONIC CIRCUIT ANALYSIS
Hours / Week Marks
Year Semester C
II I 4 - - 4 30 70 100
Course Description
The course is designed to provide students with fundamental principles of electronic
circuit design and analysis. Students are engaged in the study of basic concepts of BJT & its
design, analysis of MOS amplifier, feedback amplifiers, oscillators, power and tuned
amplifiers and their applications. This course also helps students to develop the skills to
analyze and design electronic circuits that utilize the devices. This course includes Circuit
models for electronic devices such as BJT, FET as amplifiers, dc and ac circuit models for the
design and analysis of electronic circuits and also analysis and design of Single-stage and
multistage amplifier circuits, low-frequency and high-frequency response of amplifiers.
Prerequisites
Requires the knowledge of Electronic Devices and Circuits.
COURSE OBJECTIVES:
Students will be able to
1. Design RC coupled amplifier and analyze its performance using simplified hybrid model.
2. Illustrate the effect of coupling and by-pass capacitors at low frequencies and stray
capacitances at high frequencies.
3. Describe the effect of negative feedback on amplifier characteristics and to analyze the
feedback amplifiers (voltage series, voltage shunt, current series and current shunt).
4. Discuss the concept of positive feedback and explain RC and LC oscillators
5. Evaluate the efficiency of power amplifiers (class A and B) and explain tuned amplifiers
(single, double and staggered).
COURSE OUTCOMES:
1. Design RC coupled amplifier for the given specifications and analyze its performance.
2. Explain MOSFET amplifiers.
3. Discuss the frequency response of a given amplifier.
4. Explain the effect of negative feedback on amplifiers.
5. Illustrate the generation of sinusoidal signals at audio and radio frequencies using
oscillators.
6. Evaluate the efficiency of a given power amplifier.
7. Explain the concept of tuned amplifiers.
8. Compare small signal and large signal amplifiers.
UNIT – I
Single Stage and Multi Stage Amplifiers: Classification of Amplifiers – Analysis of CE,
CC, and CB Configurations with simplified Hybrid Model, Analysis of CE amplifier with
Emitter Resistance, Emitter follower, Miller‟s Theorem and its dual, design of single stage
RC coupled amplifier using BJT.
Different coupling schemes used in amplifiers – RC coupled amplifier, Transformer coupled
amplifier, direct coupled amplifier, Analysis of Cascaded RC coupled BJT amplifiers,
Cascode amplifier, Darlington pair, Distortion in Amplifiers
UNIT – II
BJT and MOS Amplifiers – Frequency Response: Logarithms, Decibles, frequency
response of BJT amplifier, analysis at low and high frequencies, effect of coupling and
bypass capacitors, the hybrid-pi common emitter transistor model, CE short circuit current
gain, single stage CE Transistor Amplifier Response, gain-bandwidth product.
Basic concepts, MOS Small signal model, common source amplifier with resistive load,
diode connected load and current source load, source follower, common gate stage cascade
amplifier and their frequency response.
UNIT – III
Feedback Amplifiers: Concepts of feedback, classification of feedback amplifiers, general
characteristics of negative feedback amplifiers, effect of feedback on amplifier
characteristics, voltage series, voltage shunt, current series and current shunt feedback
configurations, illustrative problems.
UNIT – IV
Oscillators: Classification of oscillators, conditions for oscillation, RC phase shift oscillator,
generalized analysis of LC oscillators, hartely, and colpitts oscillators, wien-bridge and
crystal oscillators, stability of oscillators
UNIT – V
Large Signal and Tuned Amplifiers: Classification. Class A Large signal amplifiers,
Transformer coupled class A audio power amplifier, efficiency of class A amplifier, class B
amplifier, efficiency of class B amplifier, class-B Push-pull amplifier, Complementary
symmetry class B Push-pull amplifier, distortion in power amplifiers, thermal stability and
heat sinks.
Introduction, Q-Factor, small signal tuned amplifiers, effect of cascading single tuned
amplifiers on bandwidth, stagger tuned amplifiers, stability of tuned amplifiers.
TEXT BOOKS:
1. Jacob Millman and Christos C Halkias, “Integrated Electronics”, TMH, 2008.
2. S. Salivahanan, N. Suresh Kumar and A Vallavaraj, “Electronic Devices and Circuits”, 2nd
Edition, TMH, 2009.
REFERENCE BOOKS:
1. Robert L. Boylestad and Louis Nashelsky, “Electronic Devices and Circuits Theory”, 9th
Edition, Pearson Education, 2008.
2. K Lal Kishore, “Electronic Circuit Analysis”, BSP, 2004.
3. Niamen, Donalda, “Electronic Circuits Analysis and Design”, TMH, 2012.
4. Millman Jacob, “Electronic Devices and Circuits”, 2nd Edition, TMH, New Delhi, 2009.
WEBSITES
1. www.cc.ee.ntu.edu.tw/~lhlu/eecourses/Electronics1/Electronics_Ch4.pdf
2. www.techpowerup.com/articles/overclocking/voltmods/21
3. www.pa.msu.edu/courses/2014spring/PHY252/Lab4.pd
4. www.iet.ntnu.no/courses/ttt4100/oppg1_eng.pdf
5. www.te.kmutnb.ac.th/~msn/225301reports156-2.pdf
6. http://www.unix.eng.ua.edu/~huddl/mystuff/ECE333/ISM
7. Electronic%20Circuit%20Analysis%20and%20Design.pdf
CONTENT BEYOND SYLLABUS:

Phase lead phase lag networks, LC coupled amplifier, Class AB and Class C power
amplifiers.
LECTURE PLAN
Sl. Lecture Suggested books

No. No. with Page Nos.
UNIT – I Single Stage and Multi Stage Amplifiers: (No. of Lectures – 16)
Categorization of amplifiers with L1
1 Classification of Amplifiers TB1, 372-373
Examples
Amplitude, Frequency and Phase
2 Distortion in Amplifiers L2 TB1, 373-374
distortions
Analysis of Transistor in C.B
Configuration using Simplified L3 TB2, 6.25-6.26
Hybrid Model
Analysis of Transistor in C.E

Configuration using Simplified L4 B2, 6.15-6.18
Hybrid Model
Expression for voltage gain, current
3 Analysis of CE amplifier with gain, input impedance and output
Emitter Resistance using impedance L5 TB2, 6.20-6.21
Simplified Hybrid Model
Analysis of Transistor in C.C

Configuration & Emitter L6 TB2, 6.25-6.26
Follower using Simplified
Hybrid Model
4 Miller's Theorem and it's dual Definition & Proof L7 TB1, 255-266
Design concepts and Equations for L8
Design of single stage RC TB2, 6.68-6.76
5 circuit components L9
coupled amplifier using BJT
RC coupled amplifier, Transformer
Different coupling schemes used L10
6 coupled amplifier and direct coupled RB4, 245
in amplifiers L11
amplifier
7 L13
Cascode amplifier Explanation and Analysis TB1, 560-563
L14
L15
8 Darlington pair Explanation and Analysis TB1, 274-279
L16
UNIT –II BJT and MOS Amplifiers- Frequency Response (No. of Lectures – 16)
9
Logarithm, decibels Basic concept and Problems L17 TB1, 388
Frequency Response of BJT Explanation of Frequency Response of

10 L18 TB1, 389-390
Amplifier RC Coupled Amplifier
L19
Analysis(of frequency response) Analysis using Low Pass and High Pass
11 L20 TB1, 374-378
at low and high frequencies RC circuits.
L21
Effect of coupling and bypass
12 Derivation for CE and CC L22 TB2, 6.27-6.32
capacitors
Hybrid-pi model for common Justification of each parameter in the
13 L23 TB2, 6.33
emitter transistor model & it's expressions
Concept & Derivation for CE short L24
14 CE short circuit current gain TB1, 356-359
circuit current gain
CE current gain with Resistive Effect of load on B.W & Derivation for L25
15 TB1, 359-361
Load CE current gain with resistive load
L26
16 gain-bandwidth product Concept & derivation TB1, 365-367
Basic concepts of MOSFET & Justification of each parameter in the L27
17 TB1, 313-319
it's Small signal model model()
18 Common Source amplifier with Explanation and Analysis (i.e expression L28 TB1, 329-331
resistive load, diode connected for voltage gain, input impedance and L29
load and current source load output impedance)
L30
19 Source follower Explanation and Analysis TB1, 334-335
20 Common gate amplifier Explanation and Analysis L31 TB1, 341-343
21 Cascode amplifier Explanation and Analysis L32
UNIT –III Feedback Amplifiers (No. of Lectures – 11)
Basic concepts of feedback with block

L33
22 Concepts of feedback diagram & derivation for negative TB2, 7.1
feedback
Classification and general Categorization of feedback amplifiers
23 characteristics of negative with Examples. L34 TB2, 7.2-7.3
feedback amplifiers Merits & Demerits
Effect of negative feedback on Gain, L35
Effect of feedback on amplifier Noise, Distortion, Input impedance, L36
24 TB2, 7.4-7.7
characteristics Output impedance and Bandwidth of L37
amplifier & Problems L38
Analysis(i.e. Gain, Input and Output
L39
Voltage Series, Voltage Shunt, impedances) of Practical feedback TB2, 7.7-7.9
L40
25 Current Series and Current shunt amplifier circuits. TB2, 7.11-7.13
L41
feedback configurations TB2, 7.13-7.18
L42
L43 TB2,7.4-7.6,7.9-
26 Illustrative Problems Problems on above topics
7.10, 7.16
UNIT – IV Oscillators : (No. of Lectures – 10)
Basic concepts, Derivation for positive
Oscillators, conditions for
27 feedback, Condition for Oscillations & L44 TB2, 8.1-8.2
Oscillations
Starting voltage
Categorization of Oscillators with
28 Classification of Oscillators L45 TB2, 8.1-8.4
Examples.
Explanation & Derivations for Resonant L46
29 RC phase shift oscillator TB2, 8.14-8.16
frequency and condition for oscillations L47
L48
Explanation & Derivations for Resonant
30 Wien-bridge oscillator TB2, 8.25-8.27
frequency and condition for oscillations
Generalized analysis of LC Derivation of General Equation for LC
31 L49 TB2, 8.3-8.5
oscillators oscillator
Explanation & Derivations for Resonant
32 Hartley oscillator L50 TB2, 8.6-8.7
Explanation & Derivations for Resonant TB2, 8.9-8.10

33 Colpitts oscillator L51
Basic concepts of Crystals &

34 Crystal oscillator L52 TB2, 8.29-8.31
Explanation of oscillator using crystals
35 Stability of oscillators Amplitude and frequency stability L53 TB2, 8.34-8.35
UNIT –V Large Signal and Tuned Amplifiers : (No. of Lectures – 12)
Classification of Large signal Basic concepts & Categorization of
36 L54 TB1, 373
amplifiers power amplifiers
Explanation & Derivations of
37 Class A Large signal amplifiers L55 TB1, 677-678
Efficiency. Problems
Transformer coupled class A Explanation & Derivations of
38 L56 TB1, 684-687
audio power amplifier Efficiency. Problems
39 class B power amplifier L57 TB1, 692-693
40 class-B Push-pull amplifier L58 TB1, 690-695
41 Complementary symmetry class Explanation & Derivations of L59 TB1, 693-695
B Push-pull amplifier, distortion Efficiency. Problems
in power amplifiers
Explanation and Derivations of TB1, 679-681,
42 Distortion in Power Amplifiers L60
Harmonic and Cross-over distortions 699
Thermal resistance, condition for
43 Thermal stability and heat sinks L61 TB1, 5.22-5.27
thermal stability, types of heat sinks
RB4, 399
44 Tuned amplifiers Introduction, Q-Factor L62
RB5, 13.28
L63
45 Small Signal tuned amplifiers Expression for gain and bandwidth RB4, 400-403
Effect of cascading single and
46 double tuned amplifiers on Expression for bandwidth L64 RB4, 411-415
bandwidth
Stagger tuned amplifiers, Explanation of stagger tuning &
47 L65 RB4, 415
Stability of tuned amplifiers Stability of tuned amplifiers
REVIEW QUESTIONS
UNIT-I
1. Explain how amplifiers are classified?

2. Explain various types of distortions occur in amplifiers with neat sketches.
3. Draw a self-biased CE amplifier circuit without bypass capacitor. Also derive the
expressions (using simplified hybrid model) for
i) Current gain ii) Input impedance iii) Voltage gain and iv) Output impedance.
4. Draw the simplified hybrid model for Emitter Follower. Also derive the expressions for
i) Current gain ii) Input impedance iii) voltage gain iv) Output impedance
5. State and prove Miller's theorem & it's dual.
6. Design Single Stage RC coupled CE amplifier(with self bias and emitter bypassed) for
the given specifications.
VCC=24 V , VCE =3 V , VRE =5 V , RS =600 Ω, f1 =100 Hz , hfe =100 , RL =120 K Ω
7. Differentiate various coupling schemes used in amplifiers.
8. Draw a Two-Stage Transformer Coupled amplifier and explain its operation.
Also list it's merits, demerits and applications.
9. Draw a Two-stage Direct Coupled amplifier using BJT and explain its frequency response
with neat sketches. Also list it's merits, demerits and applications.
10. Explain Cascode amplifier in detail with a neat sketches and derive the expressions for
i) Input impedance and ii) Voltage gain.
11. Explain Darlington Emitter follower with neat sketches. Also derive the expressions for
i) Voltage gain ii) Current gain iii) Input impedance and iv) Output impedance.
UNIT-II
1. Explain the frequency response of RC coupled amplifier.
2. Explain in detail the reasons for fall of gain of RC coupled amplifier at both low and high
frequencies.
3. Explain the effect of emitter bypass capacitor and coupling capacitor on low frequency
response of single stage RC coupled amplifier. Also derive the expressions for bypass
capacitor and coupling capacitor.
4. Draw the hybrid π model for a transistor in CE configuration. Also explain the
significance of each component in the model.
5. Define CE short circuit current gain. Also derive its expression as a function of frequency
using hybrid - π model.
6. Derive the expression for CE current gain with resistive load. Also explain the effect of
load on B.W.
7. Define fα, fβ and fT. Also derive the relation between fβ and fT.
8. Draw and explain the small signal MOS model at low and high frequencies.
9. Draw and explain CS amplifier with resistive load. Also derive the expressions for
i) I/P resistance ii) O/P resistance iii) Voltage gain
10. Draw and explain CS amplifier with diode connected load. Also derive the expression
for Voltage gain.
11. Draw and explain CS amplifier with current source load. Also derive the expression
for Voltage gain.
12. Draw and explain source follower. Also derive the expressions for
13. Draw and explain CG amplifier. Also derive the expressions for
14. The h-parameters of a transistor at Ic= 10 mA , VCE =10 V and room temp. are hfe=100 ,
hie=500 Ω , | Ai |=10 at 10 M Hz and Cc=3 pF. Find i) rb‟e ii) rbb‟ iii) fT iv) f and v) Ce
15. The hybrid-π parameters of the transistor at room temperature with Ic= 1.3mA are gm =
50mA/V, rb‟e= 1KΩ, rbb‟ = 100Ω, rb‟c = 4MΩ, rce = 80KΩ,rce = 80KΩ, Cc = 3pF, Ce =
100pF. C BJT has gm = 38millimhos; rbe = 5.9Kohms, hie = 6Kohms, rbb' = 100 ohms,
Cbc =12pF; Cbe =63pF, hfe = 224 at 1KHz. Find  and  cutoff frequencies and fT.
16. The following low-frequency parameters are known for a given transistor at Ic=10 mA,
Vce=10v and at room temperature.
hie=500  hoe=4x10-5 A/v hfe=100, hoe=10-4
At the same operating point, fT=50 MHZ and Cob=3pf, compute the values of all the
hybrid -  parameters.
17. Three identical non interacting stages of amplifiers have the overall cutoff frequencies;
f L* = 10KHZ and f H* =40 KHZ. What are the values of fL and fH?
18. The parameters of a two stage BJT RC coupled amplifier are hfe = 50, hie= 1.1 K ohms,
hoe = 0 and RL = 2 K ohms. Find the value of the Coupling capacitor to give a lower 3dB
frequency of 20Hz.
19. In the three stage amplifier, the higher cutoff frequencies are: 500 kHz, 200 kHz and 100
kHz. Estimate the resulting high cutoff frequency.
UNIT-III
1. Classify the negative feedback amplifiers.
2. Explain the concept of feedback using block diagram.
3. Derive an expression for the gain of amplifier with negative feedback.
4. List out the merits & demerits of negative feedback.
5. Explain the effect of negative feedback on Gain and B.W.
6. Show that with negative feedback Gain of amplifier will be stabilized.
7. Show that with negative feedback lower cut-off frequency will be decreased and upper
cut-off frequency will be increased by 1+Aβ.
8. Explain the effect of negative feedback on Noise & Distortion
9. Show that for Voltage Shunt feedback amplifier transresistance gain, Ri and Ro are
decreased by a factor 1+Aβ.
10. With the help of network topology, obtain the expressions for I/P impedance and O/P
impedance of Current Series feedback amplifier.
11. With the help of network topology, obtain the expressions for I/P impedance and O/P
impedance of Current Shunt feedback amplifier.
12. Draw and explain practical Voltage-Series feedback amplifier circuit. Also derive the
expressions for i) Voltage gain ii) I/P impedance iii) O/P impedance
13. Draw and explain practical Current-Series feedback amplifier circuit. Also derive the
expressions for i) Transconductance gain ii) I/P impedance iii) O/P impedance
14. An amplifier has mid band gain of 125 and a B.W of 250 kHz.
i) If 4% negative feedback is introduced, find new B.W and gain.
ii) If B.W is restricted to 1 MHz , find the feedback ratio
15. The gain of an amplifier is decreased to 10000 with negative feedback from its gain of
60000. Calculate the feedback factor. Also express the amount of negative feedback n dB.
16. Calculate the Gain, I/P impedance and O/P impedance of Voltage-Series feedback
amplifier having A=300 , Ri =1.5 kΩ , Ro =50 kΩ and β=1/12.
17. An amplifier has an open loop gain of 400 and a feedback ratio of 0.05. If the open loop
gain changes by 20% due to temp. find the % change in closed loop gain.
18. An amplifier has voltage gain with feedback is 100. If the gain without feedback changes
by 20% and gain with feedback should not vary more than 2%. Determine the values of
Open loop gain (A) and feedback ratio (β)
19. An amplifier has a mid frequency gain of 800. lts upper and lower cut off frequencies are
16KHz and 40KHz respectively. What will be the band width after 2% of the signal
output is given as negative feedback?
UNIT-IV
1. Derive an expression for gain of amplifier with positive feedback.
2. Draw and explain RC Phase shift Oscillator. Also derive an expression for i) fo ii) hfe
3. Draw and explain Wein Bridge Oscillator. Also derive an expression for i) fo ii) hfe
4. Derive the general expression for frequency of oscillations of an LC oscillator.
5. Draw and explain Hartley Oscillator. Also derive an expression for fo
6. Draw and explain Colpitt's Oscillator. Also derive an expression for fo
7. What is Piezo electric effect? What are the main substances that exhibit this property?
8. Explain the stability of oscillators?
9. A Hartley Oscillator is designed with L1=2 mH , L2=20 µH and a variable capacitance.
Find the range of Capacitance values if the frequency of oscillations is varied between
950 kHz to 2050 kHz
10. In a Colpitt's Oscillator, the values of inductors and capacitors in the tank circuit are L=
40 mH, C1=100 pF and C2=500 pF. Find the frequency of oscillation.
UNIT-V
1. Differentiate small signal transistor and power transistor.
2. Differentiate small signal amplifier and power amplifier
3. Explain class A power amplifier (series fed type) with neat sketches. Also derive it's
expression for maximum efficiency. List its merits and demerits.
4. Explain class A power amplifier (transformer coupled type) with neat sketches. Also
derive it's expression for maximum efficiency. List its merits and demerits.
5. Explain Class-B power amplifier. Derive it's expression for the efficiency.
6. Explain class B push pull power amplifier with neat sketches. Also derive it's expressions
for i) Max. efficiency (n%max) ii) Pc(dc),max(total)
7. Show that no even harmonics are present in a push pull complementary circuit.
8. Explain complementary symmetry class B push pull power amplifier with neat sketches.
Also derive it's expression for theoretical Max. efficiency (n%)
9. Explain harmonic distortion in power amplifiers. Also derive the expression for total
harmonic distortion.
10. Describe cross over distortion. How it is overcome?
11. What is thermal runaway? How does a heat sink help?
12. Explain small signal capacitive coupled single tuned amplifier. Also derive it's
expressions for i) A/Ao ii) Bandwidth.
13. Explain the effect of cascading single tuned amplifiers on Bandwidth.
14. Draw the circuit of a double tuned amplifier and explain its operation.
15. Write a short notes on i) Stagger Tuning ii) stability of tuned amplifiers.
16. A class B push pull amplifier drives a load of 16 Ω connected to the secondary of Ideal
transformer. The supply voltage is 25 V. If no. of primary turns is 200 and secondary
turns is 50, Calculate i) Max. power o/p ii) efficiency iii) Max. power dissipation per
transistor.
17. A transistor supplies 2 W ac power to a load resistor of 2 kΩ. Zero-Signal dc collector
current is 30 mA and dc collector current with signal is 35 mA. Determine the Present
Second Harmonic distortion.
18. A sinusoidal signal vi=1.75 Sin 600t is fed to an amplifier. The resulting output current is
of the form io=15Sin 600t + 1.5 Sin 1200t + 1.2 Sin 1800t + 0 .5 Sin 2400t. Calculate
i) Second, Third and Fourth harmonic distortion
ii) % increase in power (because of distortion)
(EC104) PROBABILITY THEORY AND STOCHASTIC PROCESS
Hours / Week Marks
Year Semester C
II I 3 - - 3 30 70 100
COURSE DESCRIPTION
Probability theory is the branch of mathematics concerned with probability, the
analysis of random phenomena. The central objects of probability theory are random
variables, stochastic processes, and events: mathematical abstractions of non-deterministic
events or measured quantities that may either be single occurrences or evolve over time in an
apparently random fashion.
It is not possible to predict precisely results of random events. However, if a sequence
of individual events, such as coin flipping or the roll of dice, is influenced by other factors,
such as friction, it will exhibit certain patterns, which can be studied and predicted Two
representative mathematical results describing such patterns are the law of large numbers and
the central limit theorem.
PREREQUISITES
Requires the knowledge of mathematics.
COURSE OBJECTIVES:
1. Recall the concept of probability and understand the random variable.
2. Analyze the concept of operation on random variable and transformations.
3. Understand the multiple random variables and analyze the concept of operation on
multiple random variables.
4. Learn the random process concept and classify the various random processes.
5. Relate power spectrum density and autocorrelation function and analyze the probabilistic
situations in communication.
COURSE OUTCOMES:
1. Define random variable and understand the probability, events and random experiments.
2. Analyze the operations like expectation, variance and moments of single random variable.
3. Analyze the operations like expectation, variance and moments of multiple random
variables.
4. Understand the central limit theorem.
5. Understand the stochastic process in both deterministic and non deterministic types.
6. Classify the various processes, functions and state its properties.
7. Relate power spectrum density and autocorrelation function and state its properties.
8. Analyze the power spectral density of linear systems.
UNIT – I
Probability: Concept of Probability, Random Variables, Discrete and Continuous Sample
Spaces, Events, Probability Definitions and Axioms, Joint Probability, Conditional
Probability, Total Probability, Bayes‟ Theorem. Distribution and Density functions,
Properties, Binomial, Poisson, Uniform, Gaussian, Exponential, Rayleigh, Conditional
Distribution.
UNIT – II
Operation on One Random Variable – Expectations: Introduction, Expected Value of a
Random Variable, Function of a Random Variable, Moments about the Origin, Central
Moments, Variance and Skew, Chebychev‟s Inequality, Characteristic Function, Moment
Generating Function, Transformations of a Random Variable: Transformation of a Discrete
Random Variable
UNIT – III
Multiple Random Variables: Vector Random Variables, Joint Distribution Function,
Properties of Joint Distribution, Marginal Distribution Functions, Conditional Distribution
and Density – Point Conditioning, Conditional Distribution and Density – Interval
conditioning, Statistical Independence, Sum of Two Random Variables, Sum of Several
Random Variables, Central Limit Theorem, (Proof not expected).
UNIT – IV
Stochastic Processes – Temporal Characteristics: The Stochastic Process Concept,
Classification of Processes, Stationary Random Process, Ergodicity, Mean-Ergodic
Processes, Correlation-Ergodic Processes, Autocorrelation Function and Its Properties, Cross-
Correlation Function and Its Properties, Covariance and its properties.
UNIT – V
Stochastic Processes – Spectral Characteristics: Power Spectrum Properties, Relationship
between Power Spectrum and Autocorrelation Function, Cross-Power Density Spectrum,
Properties, Relationship between Cross-Power Spectrum and Cross-Correlation Function.
Spectral Characteristics of system response: power density spectrum of response, cross-
power spectral density of input and output of a linear system.
TEXT BOOKS:
1. Probability, Random Variables & Random Signal Principles - Peyton Z. Peebles, TMH,
4th Edition, 2001.
2. Probability, Random Variables and Stochastic Processes – Athanasios Papoulis and S.
Unnikrishna Pillai, PHI, 4th Edition, 2002.
REFERENCE BOOKS:
1. Theory of probability and stochastic processes- Pradip Kunar Gosh, University press
2. Probability theory and stochastic processes-mallikarjuna reddy cengage learning
3. Probability and Random Processes with Application to Signal Processing – Henry Stark
and John W. Woods, Pearson Education, 3rd Edition.
WEBSITES
1. www.math.harvard.edu
2. ebooks.cambridge.org
3. nptel.ac.in
4. https://www.maths.unsw.edu.au
5. ocw.mit.edu
1. Detection of a target
LECTURE PLAN
Sl. Lecture Suggested books with

No. No. Page Nos.
UNIT – I (No. of Lectures – 14)
Introduction of probability and its L1 3-7(A. Papoulis)
1 An overview of probability
significance 1-4(Peebles)
Introduced through sets, relative L2 3(Peebles)
2 Probability definition
frequency L3 9-14(Peebles)
L4
Pack of cards, dice, tossing of coins
Experiments and sample L5
3 experiments, definition of continuous 9(Peebles)
spaces L6
and discrete sample spaces.
Independent events, mutually exclusive L7
4 events 10& 20 (Peebles)
events, certain events, joint events
5 Joint probability Joint probability L9 14(Peebles)
6 conditional probability, total conditional probability, total probability,
L10 14-19(Peebles)
probability, baye‟s theorm baye‟s theorm
Binomial, Poisson, Uniform, Gaussian, L11
Standard distribution and Exponential, Rayleigh, Conditional L12
7 54-65(Peebles)
density functions Distribution. L13
L14
UNIT –II (No. of Lectures – 14)
7
definition of a random L15
definition of a random variable(R.V) 41(Peebles)
variable(R.V)
Classification of Random
variables, condition for a Continuous, discrete, Mixed random L16
8 41-43(Peebles)
function to be a random variables
variable
Distributions and density Definitions, properties L17
9 functions L18 44-50(Peebles)
expected value of a R.V, expected value of a R.V, function of a

10 L19 77-80(Peebles)
function of a R.V R.V
moments about the origin, Mean, mean square value, variance, L20
11 81-83(Peebles)
central moments skew
characteristic functions,
characteristic functions, moment L21
12 moment generating 84-86(Peebles)
generating function. L22
function.
L23
Transformations of a Transformation of a Discrete R.V,
13 L24 87-92(Peebles)
Random Variable continuous R.V
L25
L26
14 problems Of all topics L27 32,66 & 97(Peebles)
L28
UNIT –III (No. of Lectures – 11)
L29
16 Vector Random variables. Introduction, definition 108(Peebles)
joint distribution, density joint distribution, density functions and L30

19 109-115(Peebles)
functions and its properties its properties L31
L32
conditional distribution and Point conditioning and interval
20 L33 116-120(Peebles)
density conditioning
statistical independence L34
21 Statistical independence ,problems 121(Peebles)
,problems L35
sum of two R.V's, sum of
22 sum of two R.V's, sum of several R.V's. L36 122-124(Peebles)
several R.V's.
23 central limit theorem. central limit theorem. L37 125-128(Peebles)
L38
24 problems problems L39 129(Peebles)
UNIT-IV (No. of Lectures – 11)

25 Introduction introduction L40 179(Peebles)
29 Classification of R.P Continuous and disrete L41 179-184(Peebles)
first-order stationary processes, second-
concept of stationary and
30 order and wide sense stationarity, N L42 185-188(Peebles)
statistical independent
order and strict sense stationarity
Time averages and Mean ergodic processes, correlation L43
31 189-193(Peebles)
ergodicity ergodic processes L44
Auto correlation and cross L45
Auto correlation and cross correlation
32 correlation functions and its L46 194-198(Peebles)
functions and its properties
properties
Covariance and its
33 Covariance and its properties L47 198(Peebles)
properties
L48
34 problems problems L49 169 & 208(Peebles)
L50
UNIT –V (No. of Lectures – 10)
35 Power Spectrum Properties Power Spectrum Properties L51 220-226(Peebles)
Relationship between power
Relationship between power spectrum
36 spectrum and Auto L52 227-230(Peebles)
and Auto correlation function
correlation function
The cross power density
37 The cross power density spectrum L53 230(Peebles)
spectrum
L54
38 properties, problems properties, problems 230-234(Peebles)
L55
Relationship between cross
Relationship between cross power
39 power spectrum and cross L56 234-237(Peebles)
spectrum and cross correlation function
correlation function
power density spectrum of response,
Spectral Characteristics of
40 cross-power spectral density of input and L57 280-286(Peebles)
system response
output of a linear system
L58
41 problems problems L59 256 & 329(Peebles)
L60
REVIEW QUESTIONS
UNIT I: PROBABLITY
1. a. Find the probability of obtaining 14 with 3 dice.

b. A class has only 3 students A, B, C who attended the class independently. The
probability of their attendance on any day being 1/2, 2/3, 3/4 respectively. Find
the probability that the total number of attendances in two consecutive days is
exactly three.
2. a. Explain Poisson approximation to Binomial law.
b. There are 500 misprints in book of 500 pages. What is the probability that a given
page will contain at most 3 misprints?
3. a) State and prove Baye‟s theorem.
b) State and prove any four properties of conditional probability.
4. a) What is the probability that a positive integer not exceeding 100 selected at random is
divisible by 5 or 7?
b) The diameter of a cable, say X, is taken to be a random variable with probability
density function (pdf) fx(x) = 6x (1-x), 0  x  1. Verify whether fx(x) is pdf.
5. a. Define joint and conditional probability.
b. In a box there 500 coloured balls: 75 black , 150 green, 175 red, 70 white and 30
blue what are the probability of selecting a ball of each colour.
6. a. State and prove properties of probability density function.
b. A random variable X has the distribution function
12
n2
f X ( x)   u ( x  n).
n 1 650
Find the probabilities of P {-   x  6.5}.


7. a. Give the definition of probability and axioms.
b. A book containing 100 pages is opened at random. Find the probability that on
the page.
i) A doublet is found. ii) a number whose sum of digits is 10.
8. a. State and prove the properties of cumulative distribution function.
b. A sample space is defined by the set S = {1,2,3,4}. A random variable x is
defined by y = x(s) = s3. If the probability of S are P(1) = 4/24, P(2) = 3/24, P(3)
= 7/24 and P(4) = 10/24. Then find the probability of random variable Y.
9. a. A missile can be accidentally launched if two relays A and B both have failed.
The probabilities of A and B failing are known to be 0.01 and 0.03 respectively. It
is also known that B is more likely to fail (probability 0.06) if A have failed.
i. What is the probability of an accidental missile launch?
ii. What is the probability that A will fail if B has failed?
Are the events “A fails” and “B fails” statistically independent?
b. Trains X and Y arrive at a station at random between 8 a.m. and 8.20 a.m. Train
X stops for four minutes and train Y stops for five minutes. Assuming that the
trains arrive independently of each other, determine
i. The probability that the train X arrives before train Y.
ii. The probability that the trains meet at the station.
iii. Assuming that the trains met, determine the probability that the train X
arrives before train Y.
10. a. Define a random variable. State the properties of a probability distribution
function.
b. Find the value of A such that the following function is a valid probability density
function.
fx(x) = 0 X<-1
2
A(1-x ) cos(πx/2) -1≤x≤1
0 1<x
UNIT II: OPERATIONS ON ONE RANDOM VARIABLE
11. a. Derive the variance of Poisson distribution.

b. The first, second and third moments of a probability distribution about the point 2
are 1, 16, -40 respectively. Find the mean, variance and the third central moment.
12. a) What are the effects of change of scale on moment generating function?
b) Derive the variance of Binomial distribution.
13. a) A Random variable X has pdf 12x2 (1 – x) where 0  x  1, compute P( x -    2 )
and compare it with the limits given by chebycheff‟s inequality.
b) X1, X2 and X3 are continuous independent random variables with mean value 1, -1
and 2 respectively and variances 0.5, 2 and 0.5 respectively. If Z = X1 + X2 + X3,
write the approximate probability density function of random variable Z.
14. a. Calculate the mean of Rayliegh random variable.
b. In an experiment when two dice are thrown simultaneously find expected value of
sum of number of points on them.
15. a. Calculate the mean of Gaussian random variable.
b. In an experiment when two dice are thrown simultaneously. Find the expected
value of sum of number of points on them.
16. a. A random variable x has the density
3
fx(x) = (-x2+8x-12) ; 2< x < 6
32
=0 ; otherwise
Find all moments about origin.
17. a. A Gaussian random variable X has a mean value 0 and variance 9. The voltage X
is applied to a square law, full wave diode detector with a transfer function
characteristic Y = 5X. Find the mean value of the output voltage Y.
b. Show that the characteristic function of a random variable having binomial

density function is x -p+pe )]N.
UNIT III: MULTIPLE RANDOM VARIABLES
18. The joint density function of two continuous random variable X and Y is given by
fXY
= 0 otherwise
i) Find the conditional density functions fX/Y(x/y) and fY/X(y/x).
ii) Find the marginal density functions fX(x) and fY(y).
19. The joint probability density function of two random variables X and Y is given by
1  3 x 2  xy  y 2 
2
fXY(xy) = e
 3
Determine the marginal probability density function fX(x) and fY(y).
20. a)Random variables X and Y have a joint probability density function given by
1
 , for x 2  y 2  1
f XY ( x, y )  

0 otherwise
Determine whether random variables X and Y are a) Statistically independent b)
Uncorrelated.
b. State and prove any four properties of joint density function of two random
variables.
21. a. Find the marginal densities of X and Y using the joint density.
f XY ( x, y)  [u ( x)  u ( x  4)]u ( y) y 3 exp[ ( x  1) 2 y] 
10
4
b. Explain conditional distribution and density for point conditioning and interval
conditioning.
22. a. Find the mean value.
b. Variance of a random variable with
1  x  m b.
f X ( x)  e
2b
Where m and b are real constants b>0 and    m  
23. a. A random variable x ahs the probability density

 x
 cos( ) ;4  x  4
fx(x) = 16 8

0 ; elsewhere
Find its mean value.
b. Its second moment and its variance.
24. a. Determine the given function is a valid probability distribution function.
0
1 x0

FX x   
3 0 x
1
1 2
b. For real constants b > 0, c > 0, and any a, find a condition on constant 'a' and a
relationship between 1
x  'c' and 'a' (for given b) such that the function given below is
2
a valid probability density function.
a1  x b  0 xc
f x   
0 elsewhere
25. a. fxy(x,y) = b(x+y)2 -2<x<2 and -3<y<3
o Else where
Find the constant b such that this is a valid joint density function.
Determine the marginal density functions fX(x) and fY(y).
b. Random variables X and Y have the joint density function
fxy(x,y) = (x+y)2 /40 -1 <x< 1 and -3<y<3
o Else where
i. Find the second order moments of X and Y.
ii. What are the variances of X and Y?
iii. What is the correlation coefficient?
UNIT IV: STOCHASTIC PROCESS – TEMPORAL CHARACTERISTICS
1
26. a. Let Z be a random variable with probability density fZ(z) = in the range -1
2
2
.
Show that X and Y are uncorrelated.
b. Show that if any two random variables are statistically independent, then they are
also uncorrelated.
27. Explain the properties of cross correlation function of second order stationary process.
28. a) Show that if two random variables are uncorrelated and one of them has Zero mean,
then they are also orthogonal.
b) X and Y are two statistically independent random variables with values X  2, Y  4
respectively and second moments E[X2] = 8, E[Y2] = 25 respectively. Random variable
W = 2X – Y. Determine variance  2 of W.
29. List and explain the properties of auto correlation function of wide sense stationary
process.
30. a. State and prove properties of stationary random process.
b. Give that a process X(t) has the autocorrelation function.
RXX ( )  A.e  ( ) cos(w0 )
Where A>0,   0 and w0 are real constants find the power spectrum of x(t)
31. a. Explain the concept of stationary and statistical independence.
b. For a linear system find out autocorrelation of the output.
32. a. State and prove properties of auto correlation function.
b. If x(t) is a stationary random process having a mean value E{x(t)} = 3, auto
correlation function Rxx(  ) = 9  2e | | Find the mean value.
33. a. Explain the classification of random processes.
b. For a linear system, if input mean and variance are given, find the mean and
variance of the output.
34. a. Write short notes on variance and skew.
b. Given the random process X(t) = A sin( 0 are constants
-
new random process Y(t)=X2(t).
i. Find the autocorrelation function of Y(t)
ii. Find the cross correlation function of X(t) and Y(t).
iv. Are X(t) and Y(t) wide sense stationary?
UNIT V: STOCHASTIC PROCESS – SPECTRAL CHARACTERISTICS
35. State & prove Wiener-Khintchine relation.
36. a) Find average power of a power spectrum of a random process.
 2
4  ( ), /  /  6
S XY ( )   9

 0, elsewhere
b) State and prove the properties of the power density spectrum.
37. a. Given the power density spectrum of the response of a linear time invariant
system having a transfer function H ( )
b. Compare Gaussian and Poisson Random process.
38. a. Define cross power density spectrum. State the properties of cross power density
spectrum.
b. Give the spectral characteristics of a linear system for a given input.
39. Let X(t) and Y(t) be both zero-mean and WSS random processes. Consider the random
process Z(t) defined by Z(t)=Y(t) + X(t). Determine the autocorrelation function and the
power spectral density of Z(t), (i) if X(t) and Y(t) are jointly WSS; (ii) if X(t) and Y(t)
are orthogonal.
40. Explain the relationship between Power spectrum and autocorrelation function.
Short Questions
1. Define a property of Independent event.

2. Explain in brief Binomial law.
3. A coin is flipped ten times, how many possible outcomes are exactly two heads?
4. List the properties of characteristic function.
5. What are the properties of the joint distribution function?
6. How can we say that two processes are statistically independent?
7. Define cross correlation function of two random processes.
8. Explain Mean & Mean squared value of a linear system response.
9. Give the relation between auto-correlation and cross-correlation.
10. What is Ergodicity?
11. How many ways can the letters of the word ALGORTHM be arranged in a row?
12. What is probability mass function?
13. Define Skewness.
14. List two limitations of moment generating function.
15. List the properties of Joint density function.
16. State central limit theorem.
17. How are random process classified.
18. Define auto covariance function of random process X(t).
19. What are the conditions to be satisfied by a function to be Fourier transformable?
20. Give any two examples of Poisson processes.
21. Define probability and explain its use in communication system.
22. Give the properties of probability density function.
23. Illustrate the importance of Gaussian Random variable.
24. Define moments about origin.
25. Write joint and conditional probabilities for multiple random variables.
26. Differentiate temporal and spectral characteristics.
27. Give the relation between auto correlation and power spectral density.
28. Calculate the output spectral density for a given input spectral density.
29. Explain Poisson Random process.
30. Define the set theory with reference to probability.
31. Give the relation between probability density function and cumulative distribution
function.
32. Give the properties of Gaussian Random variable.
33. Define central moments of a random variable.
34. What is the cumulative distribution function of sum of two random variable.
35. What do you mean by wide sense stationary and strict sense stationary.
36. Give the relation between cross correlation and cross spectral density.
37. Calculate the cross power spectral density of input and output of a linear system.
38. Give the properties of co-variance.
39. An experiment consists of observing the sum of the dice when two fair dice are thrown.
Find (a) the probability that the sum is 7 and (b) the probability that the sum is
greater than 10.
40. State the similarities between probability density function and power density spectrum.
41. Define conditional probability and hence conditional distribution function.
42. Define Wide sense stationary process.
43. State the relation between power spectral density and auto correlation function.
44. Define Poisson random process.
45. Define random process and classify.
46. Define cross power density spectrum.
(EC105) SIGNALS AND SYSTEMS
Hours / Week Marks

Year Semester C
II I 4 - - 4 30 70 100
COURSE DESCRIPTION:
Concepts associated with Signals and Systems find wide area of application in different technological
fields such as communications, circuit design, aeronautics, speech processing and so on. This course
focuses on analyzing signals (sound, voltage, communication transmissions etc.) and the systems that
act on them (circuits, mechanical dynamics, modulation, etc.). The course presents and integrates the
basic concepts for both continuous-time and discrete-time signals and systems. Signal and system
representations are developed for both time and frequency domains. Filter design and sampling are
also discussed.
PREREQUISITES
Requires the knowledge of mathematics generally taught at higher secondary level.
COURSE OBJECTIVES:
1. Recall the basics concepts about the elementary signals.
2. Apply fourier series, fourier transform, laplace transform and Z-transform with respect to
signal processing.
3. Solve response of RLC networks using transform techniques.
4. Discuss concepts of convolution and correlation of various signal
5. Illustrate concept of sampling theorem.
COURSE OUTCOMES:
1. Retrieve the historical and natural aspects of signals and systems (remember)
2. Describe the different types of signals and systems (understand)
3. Apply the mathematical operations on signals (apply)
4. Distinguish the type of transform (fourier / laplace / Z) required to analyze the given signal
(analyze)
5. Apply the relation between time domain and frequency domain representations of signals
and their applications in filters (apply)
6. Compare the advantages and disadvantages of operating in time / frequency domain
(analyze)
7. Evaluate the response of a system for a given signal (evaluate)
8. Design of RLC circuits, stable systems (create)
UNIT I
INTRODUCTION Definitions of a signal and a system, classification of signals, basic
Operations on signals, elementary signals, Systems viewed as Interconnections of operations,
properties of systems.
UNIT II
TIME-DOMAIN REPRESENTATIONS FOR LTI SYSTEMS: Convolution, impulse
response representation, Convolution Sum and Convolution Integral, Properties of impulse
response representation, Differential and difference equation Representations, Block diagram
representations.
UNIT III
FOURIER SERIES: Introduction, Discrete time and continuous time Fourier series
(trigonometric Fourier series representation and exponential Fourier Series representation),
Properties of Fourier series (No proof), Applications of Fourier series. Sampling Theorem
and Reconstruction.
UNIT IV
APPLICATIONS OF FOURIER REPRESENTATIONS: Introduction, Frequency
response of LTI, Fourier transform representation of periodic signals, Fourier transform
representation of discrete time signals.
LAPLACE TRANSFORMATION & APPLICATIONS: Review of Laplace transforms,
waveform Synthesis, initial and final value theorems, step, ramp and impulse responses,
convolution theorem, solution of simple R-L, R-C, RL-C networks.
UNIT V
Z-TRANSFORMS: Introduction, Z – transform, properties of ROC & Z – transforms
Inverse Z–transforms, unilateral Z- Transform, analysis of LTI Systems and application to
solve Difference equations.
TEXT BOOKS:
1. Alan V Oppenheim, Alan S, Willsky and A Hamid Nawab, “Signals and Systems”
Pearson Education Asia / PHI
2. Simon Haykin and Barry Van Veen “Signals and Systems”, John Wiley & Sons,
REFERENCE BOOKS:
1. B. P. Lathi, “Linear Systems and Signals”, Oxford University Press, 2005
2. H. P Hsu, R. Ranjan, “Signals and Systems”, Scham‟s outlines, TMH, 2006
WEBSITES
1. http://nptel.ac.in/courses/117104074/
2. https://www.youtube.com/watch?v=h-CdTxDShho&list=PLC6210462711083C4
3. http://ocw.mit.edu/resources/res-6-007-signals-and-systems-spring-2011/lecture-notes/
4. http://www.tutorialspoint.com/signals_and_systems/index.htm
5. www.google.com
 Applications in Communication Engineering
LECTURE PLAN
Suggested book
(Signals &
Sl. Lecture
Topics in syllabus Modules and Sub modules Systems by
No. No.
Oppenheim) with
Page Nos.
UNIT – I Introduction (No. of Lectures: 14)
Motivation and some historical aspects, 1
1 Introduction
engineering applications L1
Definitions of a signal Definition and examples of signal and
2 L2 1, 38
and a system system
Continuous-time and Discrete-time,
L3
Continuous-value and Discrete-value,
3 Classification of signals L4 5, 11−25
Periodic and Aperiodic, Even and Odd,
L5
Energy and Power signals
Time and Amplitude Scaling, Time Shifting, L6
Basic operations on
4 Time reversal, Multiple transformations, L7 8
signals
Differentiation and Integration L8
Sinusoidal, Real and complex Exponential,
L9
5 Elementary signals Unit Step, Impulse, Ramp, Signum, Sinc, 1, 15
L10
Rectangular pulse, Triangular
Systems viewed as
6 Effect of Parallel and Cascade representation
Interconnections of L11 41
of Systems
operations
Homogeneity, Time Invariance, Additivity,
L12
Linearity and Superposition, Stability,
7 Properties of systems L13 44−53
Causality, Orthogonality Memory,
L14
Invertibility
UNIT –II Time-Domain Representations for LTI Systems (No. of Lectures :10)
1
Convolution Need for convolution L15 74
Significance of Impulse response

Impulse response
2 Mathematical representation of Impulse L16 77, 94
representation
response
Discrete-Time LTI Systems and
Convolution Sum
Convolution Sum and L17,L18
3 Continuous-Time LTI Systems and 75−94
Convolution Integral L19,L20
Convolution Integral
Properties of impulse
4 Impulse response properties of LTI systems L21 103
response
Linear Constant -Coefficient Differential
Differential and Equations
L22
5 difference equation Linear Constant-Coefficient Difference 116−124
L23
Representations Equations
Block Diagram Representations of First-

Block diagram
6 Order Systems Described L24 124
representations
by Differential and Difference Equations
UNIT –III Fourier Series (No. of Lectures: 13)
Introduction and Historical Perspective L25
1 Introduction Response of LTI Systems to Complex L26 177−182
Exponentials
Fourier Series Representation of
Discrete time and
Continuous-Time Periodic Signals L27, L28 186−190
2 continuous time Fourier
Fourier Series Representation of Discrete- L29, L30 211−212
series
Time Periodic Signal
Properties of Continuous-Time and
Discrete-Time Fourier Series: L31
Properties of Fourier Linearity, Time Shifting, Time Reversal, L32 202−205
3
series Time Scaling, Multiplication, Conjugation L33 221−223
and Conjugate Symmetry, Parseval's L34
Relation
Applications of Fourier
4 Application in Filters L35 231−245
series
Representation of a Continuous-Time Signal
Sampling Theorem and by Its Samples L36
5 514
Reconstruction Impulse-Train Sampling L37
Reconstruction of a Signal from Its Samples
UNIT – IV Applications of Fourier Representations & Laplace Transformation (No. of Lectures: 15)
Need for Fourier transform
1 Introduction L38 284
Frequency response of LTI systems
Fourier transform Fourier transform of Continuous-Time
L39
representation of aperiodic signals
2 L40 285−328
continuous-time Properties of the Continuous-Time Fourier
L41
aperiodic signals Transform
Fourier transform Fourier transform of discrete time aperiodic L42
representation of signals L43
3 358−390
discrete-time aperiodic Properties of the discrete time Fourier L44
signals Transform
Laplace Transform definition
L45
Region of Convergence for Laplace
Review of Laplace L46 655,662,670,
4 Transforms
transforms L47 682−691
Inverse Laplace Transform
L48
Properties of Laplace Transform
Initial and Final value Definitions
5 L49 690
theorems Usefulness of these theorems
Definition L50
6 Convolution theorem 693
Application in LTI systems L51
Solution of simple R-L,
7 Network solutions using Laplace Transform L52 700
R-C, RL-C networks
UNIT –V Z-Transforms (No. of Lectures: 08)
1 Introduction Need for Z-transforms L53 741
Definition of Z-transform
L54
Z – transform and How to draw ROC
2 L55 741−774
properties of ROC Importance of ROC
L56
Properties of Z-transform
3 Inverse Z–transforms Inverse Z–transforms L57 757
Unilateral Z–
4 Unilateral Z- Transform L58 789
Transform
Analysis of LTI Analysis of LTI Systems in terms of
Systems and Causality, Stability L59
5 774−781
application to solve Solution of Difference equations using Z- L60
Difference equations Transform
Review Questions
1.1. Give two examples for each of the following signals

a) Continuous-time and Discrete-time
b) Continuous-value and Discrete-value
c) Discrete-time discrete-value
d) Periodic and Aperiodic
e) Even and Odd
f) Energy and Power
1.2. Explain (a) Unit step function (b) Exponential function (c) Sinc function
1.3. Let x[n] be a signal with x[n] = 0 for n < −2 and n > 4. For each signal given
below, determine the values of n for which it is guaranteed to be zero
(a) x[n − 3] (b) x[n + 4] (c) x[− n] (d) x[− n + 2] (e) x[− n − 2]
1.4. If g(t) = 7e −2t −3, write out and simplify the following function
 t 
(a) g(3) (b) g(2−t) (c) g   4  (d) g( jt) (e)
 10 
g (( jt  3) / 2)  g (( jt  3) / 2)
2
1.5. Determine whether or not each of the following functions is periodic. If the signal is
periodic, determine its fundamental period.
 
(a) x(t )  3 cos(4t  ) (b) x(t )  [cos(2t  )]2 (c) x(t ) e j (t 1)
3 3
6 n  
(d) x[n]  sin( n  1) (e) x[n]  cos(   ) (f) cos( n) cos( n)
7 8 2 4
1.6. Sketch the signal x(t) = r(t + 2) – r(t + 1) – r(t – 1) + r(t – 2)
1.7. A continuous-time signal x(t) is shown in Figure 1.1. Sketch and label carefully
each of the following signals:
t
(a) x(t − 1) (b) x(2 − t) (c) x(2t + 1) (d) x (4  ) (e) [x(t)+x(-t)]u(t)
2
3 3
(f) x(t )[ (t  )   (t  )]
2 2
1.8. A discrete-time signal is shown in Figure 1.2. Sketch and label carefully each of
the following signals:
(a) x[n−4] (b) x[3−n] (c) x[3n] (d) x[3n+1] (e) x[n]u[3 − n]
1 1
(f) x[n − 2]δ[n − 2] (g) x[n]  (1) n x[n] (h) x[(n − 1)2]
2 2
1.9. Find the even and odd parts of these functions
(a) g(t)= 2t2 −3t + 6 (b) g(t) = sinc (t) (c) g[n] = cos(0.5πn)
1.10. Explain the perseval‟s energy theorem.
1.11. Find the signal energy of the following signals
(a) x(t )  2rect (t ) (b) x(t )  A(u(t )  u(t  10)) (c) x(t )  rect (t ) cos(2t )
(d) x[n] = A δ[n]
1.12. Find the signal power of the signals: (a) x(t )  A (b) x(t )  A cos(2ft   )
1.13. Define LTI system with examples.
1.14. Consider a continuous-time system with input x(t) and output y(t) related by
y(t )  x(sin(t ))
(a) Is this system causal? (b) Is this system linear?
1.15. Evaluate the following integrals
5
(a)  sin(2 t )  (t  3) dt
0

(b)  u(t ) cos(t ) dt

2.1. Let x[n] =  [n] + 2 [n − 1] −  [n − 3] and h[n] = 2 [n + 1] + 2 [n −1]
Compute and plot each of the following convolutions:
(a) y1 [n] = x[n] * h[n] (b) y2[n] = x[n + 2] * h[n]
(c) y3 [n] = x[n] * h[n + 2]
2.2. Consider an input x[n] and a unit impulse response h[n] given by
n2
1
x[n]    u[n  2]
2
h[n]  u[n  2]
Determine and plot the output y[n]  x[n]  h[n] .
2.3. Let
x(t )  u(t  3)  u(t  5) and h(t )  e 3t u(t ) .
(a) Compute y(t )  x(t )  h(t ) .
(b) Compute g (t )  (dx(t ) / dt  h(t ) .
(c) How is g(t) related to y(t).
2.4. For the following impulse responses determine whether each system is causal and/or
stable. Justify your answers.
n
1
(a) h[n]    u[n] (b) h[n]  (5) n u[3  n]
5
(c) h(t )  e 4t u(t  2) (d) h(t )  e 2t u(1  t )
2.5. Determine whether the system is Linear Time Invariant (LTI) or not: y(t)= cos(x(t)).
3.1. Find fourier-series for the following continuous-time periodic signal
 2t   5t 
x(t )  2  cos   4 sin 
 3   3 
3.2. Obtain the Exponential Fourier series co-efficient and plot its magnitude, phase
spectrum.
3.3. A continuous-time periodic signal x(t) is real valued and has a fundamental period T =
8. The nonzero Fourier series coefficients for x(t) are specified as
a1  a1  j, a5  a5  2

Express x(t) in the form: x(t )   Ak cos(wk t  k )
k 0
3.4. Write differences between Fourier Series and Fourier Transform.
3.5. State and prove time sifting property of Fourier transform.
3.6. Find Fourier Transform of the following signals and also plot the results
2 t 1 
(a) e 2(t 1) u(t  1) (b) e (c)  (t  1)   (t  1) (d) sin(2t  )
4
1
(e) ( ) n1 u[n  1] (f)  [n  1]   [n  1]
2
2 sin[3(  2 )]
3.7. Find the signal corresponding to X ( j ) 
(  2 )
3.8. State and prove the Sampling Theorem.
4.1. What is the difference between Laplace Transform and Fourier Transform?
4.2. What is the significance of Region of Convergence (ROC)?
4.3. For the following signals find the Laplace Transform and its ROC
e t sin 2t , t  0
(a) e 5t u(t  1) (b) 
0, t 0
2(s  2)
4.4. Find the inverse Laplace transform of X ( s)  2 , e{s}  3.
s  7 s  12
4.5. Determine the unilateral Laplace transform of the following signals, and specify the
corresponding regions of convergence:
(a) x(t )  e 2t u(t  1) (b) x(t )   (t  1)   (t )  e 2(t 3) u(t  1)
4.6. Determine the zero-state response of the following circuit when the input current is
x(t) = e−2t u(t).
4.7. Consider an LTI system with input x(t) = e−t u(t) and impulse response h(t) = e−2t u(t).
(a) Determine the Laplace transforms of x(t) and h(t).
(b) Using the convolution property, determine the Laplace transform Y(s) of the
output y(t).
(c) From the Laplace transform of y(t) as obtained in part (b), determine y(t).
(d) Verify your result in part (c) by explicitly convolving x(t) and h(t).
a) Compare (i.e. write differences between) Fourier Transform, Laplace Transform and
Z-Transform.
b) Determine the z-transform for each of the following sequences. Sketch the pole-zero
plot and indicate the region of convergence. Indicate whether or not the Fourier
transform of the sequence exists.
n n2
1 1
(a)  (n  5) (b)  (n  5) (c) (1) u[n] (d)   u[3  n] (e)  
n
u[n  2]
4  3
c) Let x[n]  (1) n u[n]   n u[n  n0 ] , determine the constraints on the complex
number  and the integer n0 , given that the ROC of X(z) is 1  z  2.
1
1  z 1
d) Find the inverse z-transform of X ( z )  3 , z 2
(1  z 1 )(1  2 z 1 )
e) Consider the following system functions for stable LTI systems. Determine in each
case whether or not the corresponding system is causal.
4 1 1
1  z 1  z 2 z
(a) X ( z )  3 2 (b) X ( z )  2
1 1 1 1 1 1 3
z (1  z )(1  z ) z  z
2
2 3 2 16
f) Derive the relation between discrete time Fourier Transform (DTFT) and Z-transform.
Find the z-transform and ROC for x(n) = sin(ωon) u(n).
(BS111) COMPUTATIONAL MATHEMATICS LAB
(Common to all branches)
Hours / Week Marks

Year Semester C
II I - - 3 2 30 70 100
Pre-requisite Nil
COURSE OBJECTIVES:
1. Understand the basics of spreadsheet applications to engineering problem solving
2. Use Excel and MATLAB for engineering computing and data visualization
3. Apply skills of modeling and generate engineering models
4. Illustrate scientific documentation tools
5. Apply MATLAB for solving problems in numerical methods and curve fitting
COURSE OUTCOMES:
At the end of the course, the students will develop ability to
1. Create and format spreadsheets in Excel
2. Compare different solutions to engineering problems using the scenario analysis
3. Represent program modules in terms of a flowchart and psuedocode and use MATLAB
for interactive computing
4. Write and test programs in MATLAB using flow controls (if-else, for, and while)
5. Manipulate matrices and perform matrix algebra in Excel and MATLAB
6. Solve simultaneous equations in Excel and MATLAB
7. Perform numerical integration and differentiation in Excel and MATLAB
8. Construct appropriate graphs or plots in Excel and MATLAB for data analysis and
prediction.
EXCEL
Week 1: Introduction to Excel: Formatting and Layout, Page orientation, Size, Breaks,
Header/Footer, Headings, Font, Height and Width, Color, Lines, Alignment, Merge, Wrap,
Sheets titles, Fill, Sort, Absolute and Relative referencing.
Week 2: Simple plots, Graphing with error and trend lines.
Week 3: Solving system of equations using matrix methods and the solver.
Week 4: Numerical integration and differentiation from data and from equation.
Week 5: Finding roots of a polynomial - Goal seek, Finding maximum and minimum of
function - solver, Finding the results for different scenarios.
MATLAB
Week 6: Flowcharting, Pseudocode and Documentation – Basic building blocks of flowchart,
Translating flowchart to pseudocode, Basics of documentation.
Week 7: Introduction to MATLAB environment, Writing simple programs with branching
and loop statements.
Week 8: Creating plots with MATLAB.
Week 9: Manipulating matrices and solving system of equations using matrix methods.
Week 10: Using programmer‟s toolbox (input/output/plotting..) - Finding roots, Maximum
and minimum values of a function.
Week 11: Numerical integration and differentiation.
TEXT BOOKS:
1. Bernard Liengme, “A Guide to Microsoft Excel 2013 for Scientists and Engineers”,
Elsevier.
2. Kelly Bennett, “MATLAB Applications for the Practical Engineer”, InTech, (2014).
REFERENCE BOOKS:
1. John Walkenbach, “Excel 2013 Bible”,Wiley.
2. E.Joseph Billo, “Excel for Scientists and Engineers - Numerical Methods”, Wiley,
(2007).
3. Stormy Attaway, “MATLAB: A Practical Introduction to Programming and Problem
Solving”, Elsevier, (2009).
4. V. Rajaraman, “Computer Oriented Numerical Methods”, PHI Learning Pvt. Ltd.
5. Amos Gilat, “MATLAB: An Introduction with Applications”, Wiley, (2011).
SUGGESTED READINGS:
1. Ronald Larsen, “Engineering with Excel”, Pearson, (2013).
2. Thomas J Quirk, “Excel 2010 for Engineering Statistics: A Guide to Solving Practical
Problems”, Springer, (2014).
3. MathWorks, “MATLAB Programming Fundamentals”, the math works, Inc., (2017).
4. Holly Moore, “MATLAB for Engineers”, Pearson, (2012).
5. Douglas C. Giancoli, “Physics Principles with Applications”, Pearson, (2005).
WEB LINKS:
1. http://www.mcrhrdi.gov.in/Downloads/04.MS%20Excel.pdf
2. http://www.breezetree.com/articles/how-to-flow-chart-in-excel.htm
3. http://cheserver.ent.ohiou.edu/matlab/H-2.pdf
4. https://in.mathworks.com/help/stateflow/ug/creating-flow-graphs-with-the-patternwizard.
html
(ES120) BASIC SIMULATION LABORATORY
Hours / Week Marks
Year Semester C
II I - - 3 2 30 70 100
COURSE OBJECTIVES:
1. Develop vectors, matrices, variables expressions, statements in MATLAB.
2. Sketch different types of signals in MATLAB.
3. Compute convolution, correlation of signals and sequences.
4. Sketch Fourier transform to signals.
5. Sketch Laplace transform to signals and verify Gibb‟s phenomenon.
COURSE OUTCOMES:
1. Examine basic operations on signals.
2. Discuss various signals and sequences (periodic and aperiodic).
3. Compute operations on signals and sequences.
4. Compute even and odd parts of signals / sequence and real and imaginary parts of signal.
5. Evaluate convolution between signals and sequences.
6. Apply correlation concepts of signals and sequences in various fields.
7. Use Fourier transform, Laplace transform in analysis of signals.
8. Apply sampling theorem in various applications.
LIST OF EXPERIMENTS: (Note: Minimum of any 12 experiments to be conducted)

1. Basic Operations on Matrices.
2. Generation of various signals and sequences (periodic and aperiodic), such as unit
impulse, unit step, square, saw tooth, triangular, sinusoidal, ramp, sinc.
3. Operations on signals and sequences such as addition, multiplication, scaling, shifting,
folding, computation of energy and average power.
4. Finding the even and odd parts of signals / sequence and real and imaginary parts of
Signal.
5. Convolution between signals and sequences.
6. Auto correlation and cross correlation between signals and sequences.
7. Verification of linearity and time invariance properties of a given continuous/ discrete
systems.
8. Computation of unit sample, unit step and sinusoidal responses of the given LTI system
and verifying its physical realiazability and stability properties.
9. Gibbs Phenomenon.
10. Finding the Fourier transform of a given signal and plotting its magnitude and phase
spectrum.
11. Waveform synthesis using Laplace transform.
12. Locating the zeros and poles and plotting the pole-zero maps in S plane and Z plane for
the given transfer function.
11. Generation of Gaussian noise (real and complex), computation of its mean, M.S. value
and its skew, kurtosis, and PSD, probability distribution function.
13. Sampling theorem verification
14. Removal of noise by autocorrelation / cross correlation
15. Extraction of periodic signal masked by noise using correlation
16. Verification of Weiner-Khinchine relations
17. Checking a random process for stationarity in wide sense.
(EC109) ELECTRONIC DEVICES AND CIRCUIT ANALYSIS LABORATORY
Hours / Week Marks

Year Semester C
II I - - 3 2 30 70 100
Pre-requisite Nil
COURSE OBJECTIVES:
1. Sketch the V-I characteristics of PN Junction diode and zener diode and to calculate the
static, dynamic resistance and cut-in voltage of both diodes and breakdown voltage of
zener diode from the characteristics.
2. Draw the input and output characteristics of a transistor in CE and CB configurations and
3. calculate its input and output dynamic resistance.
Sketch the characteristics of SCR and FET.
4. Draw the frequency response of single stage CE amplifiers and CS FET amplifier and to
calculate its voltage gain and bandwidth.
5. Produce sinusoidal signals by simulating / constructing Hartley and Colpitt‟s oscillators.
COURSE OUTCOMES:
1. Explain the unidirectional conduction property of p-n junction diode.
2. Discuss the regulation property of zener diode.
3. Experimentally compare the various parameters such as i/p resistance, o/p resistance
6. current gain and voltage gain of a transistor in C.E and C.B configurations.
4. Design common emitter amplifier for the given specifications and analyze its
7. performance.
5. Describe behavior and working of SCR and FET.
6. Describe the generation of sinusoidal signals at AF and RF frequencies using oscillators.
7. Compute the efficiency of class A and class B amplifier.
8. Contract and discuss the effect of feedback on the amplifier.
LIST OF EXPERIMENTS: (12 experiments to be done)

I) Testing in the Hardware Laboratory (Any 6 Experiments)
1. Forward and reverse bias characteristics of PN junction diode.
2. Zener diode characteristics and Zener as voltage regulator.
3. Input and output characteristics of transistor in CB configuration.
4. Input and output characteristics of transistor in CE configuration.
5. FET characteristics.
6. Frequency response of CE amplifier.
7. Frequency response of common source FET amplifier.
8. SCR characteristics.
9. Hartley and Colpitt‟s oscillators.
II) Design and simulation in simulation laboratory using any simulation software.
(Any 6 experiments)
1. Common emitter amplifier.
2. Common source amplifier.
3. Voltage series feedback amplifier (with and without feedback).
4. Hartley and Colpitt‟s oscillators.
5. Class A power amplifier (transformer less).
6. Class B complementary symmetry amplifier.
7. Common base (BJT)/ common gate (JFET) amplifier.
8. Single tuned voltage amplifier.
(MC102) GENDER SENSITIZATION
(Common to all branches)
Hours / Week Marks

Year Semester C
II I - - - 2 - - -
COURSE OBJECTIVES:
1. Act sensibility to issues of gender in contemporary India.
2. Develop a critical perspective on the socialization of men and women.
3. Emphasize about biological aspects of genders.
4. Judge and reflect on gender violence.
5. Expose themselves to more egalitarian interactions between men and women.
COURSE OUTCOMES:
At the end of the course, the students will develop ability to
1. Evaluate a better understanding of issues related to gender in contemporary India.
2. Sensitize to multi dimensionalities like biological, social, psychological and legal aspects
of gender.
3. Attain an insight of gender discrimination in society.
4. Acquire insight into the gendered division of labour and its relation to politics and
economics.
5. Ensure and equip them for professional equivalence.
6. Respond to gender violence and empower themselves with moral values.
7. Expose themselves to debates on the politics and economics of work.
8. Equip themselves with morality and ethics.
UNIT- I: Understanding Gender

Gender: Why should we study it? (Towards a World of Equals: Unit – 1)
Socialization: Making Women, Making Men (Towards a World of Equals: Unit – 2)
Introduction. Preparing for Womanhood. Growing up Male. First lessons in Caste. Different
Masculinities.
Just Relationships: Being Together as Equals (Towards a World of Equals: Unit – 12)
Mary Kom and Onler. Love and Acid just do not Mix. Love letters. Mothers and Fathers.
Further Reading: Rosa
Parks. The Brave Heart.
UNIT- II: Gender Biology

Missing Women: Sex selection and its consequences (Towards a World of Equals: Unit – 4)
Declining Sex Ratio. Demographic Consequences.
Gender Spectrum: Beyond the Binary (Towards a World of Equals: Unit – 10)
Two or Many? Struggles with Discrimination.
Additional Reading: Our Bodies, Our Health (Towards a World of Equals: Unit – 13)
UNIT –III: Gender of Labour

House Work: the Invisible Labour (Towards a World of Equals: Unit – 3)
“My Mother doesn‟t work.” Share the Load.”
Women’s Work: Its Politics and Economics (Towards a World of Equals: Unit – 7)
Fact and Fiction. Unrecognized and Unaccounted work. Further Reading: Wages and
Conditions of Work.
UNIT –IV : Issues of Violence

Sexual Harassment: Say No! (Towards a World of Equals: Unit – 6)
Sexual Harassment, not Eve-teasing – Coping with Everyday Harassment –Further Reading.
“Chupulu”.
Domestic Violence: Speaking out (Towards a World of Equals: Unit – 8)
Is Home a Safe Place? When Women unite (Film). Rebuilding Lives. Further Reading New
Forums for Justice.
Thinking about Sexual Violence (Towards a World of Equals: Unit – 11)
Blaming the Victim-“I Fought for my Life…” – Further Reading; The Caste Face of
Violence.
UNIT –V: Gender Studies

Knowledge: Through the lens of Gender (Towards a World of Equals: Unit-5)
TEXT BOOKS:
1. Sumeetha, Uma Bhrugubanda, Duggitala Vasanta, Rama Melkote, Vasudha Nagaraj,
Asma Rasheed, Gogu Shyamala, Deepa Sreenivas and Susie Tharu, “Towards a World of
Equals: A Bilingual Textbook on Gender”.
2. Jayaprabha, A. “Chupulu (Stares)”. Women Writing in India: 600BC to the Present.
Volume it. The 20th Century Ed. Susie Tharu and K. Lalita. Delhi: Oxford University
Press, 1995. 596-597.
REFERENCE BOOKS:
1. Sen, Amartya. “More than One Million Women are Missing.” New York review of Books
37.20(20th December 1990). Print. „We Were Making History….‟ Life stories of Women
in the Telangana People‟s struggle. New Delhi: Kali for Women, 1989.
2. K. Satyanarayana and Susie Tharu (Ed.) Steel Nibs Are Sprouting: New Dalit Writing
Form South India, Dossier 2: Telugu And Kannada
http://harpercollins.co.in/BookDetail.asp?Book_Code=3732

II Year Hand Book FInal

Uploaded by

Copyright:

Available Formats

II Year Hand Book FInal

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

II Year Hand Book FInal

Uploaded by

Copyright:

Available Formats

SR ENGINEERING COLLEGE

Ananthasagar, Warangal, Telangana – 506 371

I Semester: 12-06-2017 to 13-10-2017

S R Engineering College, Warangal was established in 2002 by S R Educational Society. It

S R Engineering College (SREC) is an autonomous and accredited institution valuing and

1. Novel technology enabled teaching and learning techniques,

PEOs (Program Educational Objectives) relate to the career and professional

I. Enhance the skill set of students by providing strong foundation in

1. Engineering Knowledge: Apply the knowledge of mathematics, science, engineering

S. No. Description Schedule Duration

MON ECA BS/EDC Lab PTSP M-II NA

THU PTSP CM LAB BS/EDC Lab

Class: II-ECE-B Room No: 2217 w.e.f.12-06-2017

WED PTSP ECA S&S NA M-II CED

GS (MC102): Gender Sensitization: Ms.G.Rajyalaxmi

CM (BS111) : Computational Mathematics: Mr. Rajbir Singh

Class: II-ECE-C Room No: 2218 w.e.f.12-06-2017

MON PTSP M-II S&S ECA NA

WED S&S ECA NA PTSP CED

THU PTSP BS/EDC Lab CM LAB

Class Teacher : Mr. S. Umamaheshwar

Hours / Week Marks

Unit-I : Laplace Transforms

Unit-III : Vector Calculus

Unit-IV: Complex Analysis - 1

Unit-V: Complex Analysis - 2

Content Beyond Syllabus:

UNIT-IV Complex Analysis – I (No. of Lectures: 17)

1.15 Find the Laplace Transform of the function: t e−t sin2t.

2.4 Find „a0‟ term in the Fourier expansion of the function f x  

2.5 Write the Dirichelet conditions of Fourier series.

to (1, 0, 0) then to (1, 1, 0) and then to (1, 1, 1).

x=2cost,y=3sint , from t=0 to t=2π.

2x+3y +6z=12 which is located in the first octant.

and (-1, 0).

4.13 Show that the function f z   z is continuous over C.

4.19 Find the singular point(s) of the function f ( z )  z 2 e1/ z

4.20 Find Taylor expansion of f(z) = 1/z about z = 1.

4.22 Prove that the function f(z) = sinhz is analytic.

 y  x  3x i dz where C consists of the line segments from z  0 to

z  i and the other from z  i to z  1  i .

the regions in which these expansions are valid.

Find the residue for f z  

Hours / Week Marks

UNIT –III (No. of Lectures – 13)

UNIT-IV (No. of Lectures – 11)

2. Find Vx using source transformation theorem.

(b) Calculate the nodal voltage using node analysis method

22. Obtain the Thevenin‟s equivalent of the following circuit.

23. Using superposition theorem find Io.

40. Transform Z-parameters in terms of ABCD and Y- parameters.

45. Two port network N as shown in figure is specified by

10 .Define form factor and crest factor.

13. State reciprocity theorem

18. If a voltage of V=80 Sin(314t+600

CONTENT BEYOND SYLLABUS:

Sl. Lecture Suggested books

Analysis of Transistor in C.E

Analysis of Transistor in C.C

Frequency Response of BJT Explanation of Frequency Response of