Daelim A-Four

HOW TO USE THIS MANUAL CONTENTS
This manual describes effective maintenance procedure for

the A-Four manufactured by DAELIM Motor Co., Ltd.
To ensure safety and optimal operating conditions of the
vehicle, carry out regular inspections according to the SERVICE INFORMATION 1
GENERAL
maintenance schedule (Section 2).
Sections 1 through 2 provide information on overall
vehicle; section 3, assembly and disassembly procedures
for external components, and section 4 describes
INSPECTIONS/ADJUSTMENTS 2
maintenance procedure for the engine, frame and electrical
systems. EXTERNAL PARTS 3
To facilitate use of this manual, each page starts with
disassembly and system diagrams, service information,
and troubleshooting guide. If you cannot find the cause of LUBRICATION SYSTEM 4
trouble, refer to Section 18: Troubleshooting.
FUEL SYSTEM 5
ENGINE
Contents of this manual and specifications are ENGINE REMOVAL/INSTALLATION 6
subject to change without prior notice for
improvement of vehicle quality. KICK STARTER/ CONTINUOUSLY
No part of this publication may be reproduced VARIABLE TRANSMISSION 7
without written permission of DAELIM Motor Co.,
Ltd.,
CYLINDER HEAD/CYLINDER/PISTON 8
TRANSMISSION/CRANKSHAFT/CRANK CASE 9
FRONT WHEEL/FRONT FORK/STEERING 10
FRAME
REAR WHEEL/BRAKE/SUSPENSION 11
BRAKE SYSTEM 12
13
ELECTRICAL SYSTEM
CHARGING SYSTEM/A.C.GENERATOR
IGNITION SYSTEM 14
STARTING SYSTEM 15
LIGHTS/METER/SWITCHES 16
WIRING DIAGRAM 17
TROUBLESHOOTING 18
1. SERVICE INFORMATION
GENERAL SAFETY 1-1 TWIST TORQUE 1-14

SERVICE RULES 1-1 SPECIALIZED TOOLS 1-16
1
CAUTION WHEN WIRING 1-5 LUBRICATION OIL 1-17
SERIAL NUMBER LOCATION 1-9 SYMBOLS 1-18
MAINTENANCE INFORMATION 1-10 WIRING DIAGRAM 1-19
GENERAL SAFETY
WARNING
1. Do not run the engine for a long time in closed or not well-ventilated area because the exhaust gas contains toxic
substances such as carbon monoxide, hydrocarbon, nitric oxide.
2. The battery fluid(lean sulfuric acid) is extremely toxic. It is dangerous if skin is exposed to it or if it enters into the eye.
Be careful in handling. When exposed to the battery fluid, wash it with water and get a medical check up.(store the
battery fluid in a safe place to avoid touching by the children)
3. Pay attention not to be burned and always put on the protection gears because the engine or the muffler is hot right after
engine stops.
4. Gasoline is extremely flammable. Maintenance must performed in the place free of the open fire or electric spark.
5. When more than two person are working, always pay attention to other worker’s action and alway have safety in mind.
6. The skin exposed to used engine oil can be a major reason of the skin cancer. Pay attention not to exposed and wash
carefully with soap and water after handling.
7. If compressed air is used to clean the brake, dust scattered in the air can be breathed in by workers. Please take action not
to scatter dust in the brake cleaner, etc.
8. Flammable nitrogen gas is generated during charging the battery so charging must be performed in well-ventilated area
and free of the open fire and spark.
SERVICE RULES
1. Parts and lubrication oil must be DAELIM genuine or 2. Before maintenance, remove deposit or dust from the
recommended parts. chasis.
1-1
SERVICE INFORMATION
3. Store the parts of each system discriminatively to install 4. After removing gasket, O-ring, piston pin clip and cotter
each part in the right place. pin, always replace them with the new one. When
removing the snap ring, it can be easily missed after
transformation or installation.
5. Clean the parts after the overhaul and before the test and 6. Check necessary place and measure necessary data
remove the cleaning oil with compressed air. Apply oil during installation. When installing, return to the state
to seal face during installation. before removing.
7. Align the bolts to uniform the tightening points before 8. Bolts, nuts and pieces must be tightened from the bigger
tightening them when you don’t know the bolt length. diameter to the smaller one, from inside to outside and
diagonally with the specified torque.
9. Check to see if the rubber part is worn out when 10. Recommended grease must be applied to or filled in
removing it and replace it if necessary. Some rubber part the specified place.
is weak to gasoline and kerosene, so pay attention not to
soak with gasoline or oils.
1-2
SERVICE INFORMATION
11. Maintenance needed to use the specialized tools must 12. Never reuse the ball bearing removed with the ball
performed with the right tool. applied pressure when removing press-fitted the
bearing.
13. Check the smooth rotation of inner or outer race of the 14. Pay attention to installation direction in case of the
ball bearing by rotating it manually. single-sided sealed ball bearing. Install the open-
• Replace the ball bearing having excessive axial/ direction or double-sided sealed bearing in the way
longitudinal hanging. that the face marked with manufacturer and size
• Wipe the ball bearing likely to have hanging with should direct to the outer axle.
cleaning oil.(except double-sided sealed type ball
bearing)
• Replace the ball bearing of which press-fitted part is
slacked at the case or shaft.
’
15. When blowing the ball bearing with compressed air 16. Install the snap ring so that chamfered side directs to
after cleaning, keep the race from rotating. High speed the load-applied side. After installation, check the
rotation of the race may damage the bearing. Prior to proper installation by rotating the snap ring.
installation, apply oil or grease to the bearing.
17. Check each part for proper tightening and operation 18. The brake fluid and coolant can damage the painted
after installation. plastic or rubber parts. Keep these parts from
contacting with them and wash these parts with water
in case of contact.
1-3
SERVICE INFORMATION
19. Install the oil seal so that the manufacturer marked 20. Connect the tube until the tube fully inserted in the
surface directs outer surface.(direction not covered joint. Install the clip if it is supplied. Replace the tube
with oil) having slacked end.
• Pay attention not to bend or damage the lip
• Apply the grease to the lip
21. Keep the pneumatic system interior or the engine 22. Install the gasket mounted in the contact surface of
interior from the infiltration of dust. each case of the engine while removing gasket
material completely. Remove damaged contact surface
by wiping with the oil stone equally.
23. Pay attention not to bend the cable excessively. 24. Install the boots with the installing groove by inserting
Transformed or damaged cable may cause malfunction the boots into the groove.
or damage.
1-4
SERVICE INFORMATION
CAUTION WHEN WIRING

•Each cord must be connected depending on its color. •When measuring voltage or resistance of the cord
When connecting different cord, attach color tube terminal using tester, contact the tester plug behind of
around the connector. Connect the coupler to the the coupler. Pay attention not to open the cord terminal
connector with same color and same pin number. and contact the tester plug from the front of the coupler
•Identify the two-colored cord by main color first and in case of water-proof coupler.
then spriped color .
•Recheck the condition of contact, securing and

continuity of each part after maintenance.
•When connecting the battery, the plus terminal must be
connected first.
•After connecting the terminal, apply the grease to the
terminal.
•When disconnecting the battery, the minus terminal •Connect covers to the terminal after maintenance.
must be disconnected first.
•Make sure that the tool such as spanner do not contact
with the frame.
•If the fuse is short-circuited, find out the cause and •If there is rust in the terminal, remove the rust with sand
repair. Replace with the fuse having the specified paper prior to connecting.
capacity.
VALIDATION REMOVE
OF CAPACITY! THE
RUST!
1-5
SERVICE INFORMATION
•Turn off the main switch before connecting/dis- •When disconnecting the coupler, disconnect it while
connecting. holding the coupler body. Pull while holding the wire
•Release the lock to disconnect the lock of the coupler. harness cord and do not remove the coupler connection.
•The lock of the coupler has two types according to
releasing method(press type and pull type) so release it
properly according to the shape.
- Typical releasing method of the coupler is illustrated in
the following.
•Insert the lock of the coupler until the lock is fully

secured.
•Release the lock by inserting the coupler slightly and •Pay attention not to damage the vinyl cover of the
then narrowing connection to remove the coupler. coupler.
•Check to see if there is bended terminal and secure it to •If the wire harness coating is damaged, repair by
avoid disconnecting. winding vinyl tape or replace it.
•Prior to connecting the connector, make sure that the
cover is not damaged and the mess terminal is not
opened.
1-6
SERVICE INFORMATION
•Insert the connector until the vinyl cover is fully •When removing T-start, broaden the groove of T-start
inserted into the terminal. using the wiring driver and release the torque.
•The opening of the vinyl cover must face at the ground •Connect the harness and the hose to T-start and then
direction but in case of the plain connector, the draining insert until the groove is locked.
opening must face at the sky direction. •When removing T-start from the frame, replace it with
the new one.
•Wire band must be secured firmly in the specified •Secure the wire harness firmly using the clamp.
location of the frame. In case of aluminium band,
secure the wire harness to the coated part.
•In case of the weld clamp, do not clamp in the welded •When clamping the wire harness, make sure that the
part. harness is not contacted with the shaft or rotating part.
•When clamping the wire, pay attention not to contact •The wire harness must be routed without contacting
with hot part. with the end of the lamp or any sharp edge.
•The wire harness must be routed without contacting
with the end of the bolt or the piece.
1-7
SERVICE INFORMATION
•In case that the wire harness is contacted with the end or •The wire must not hang down or be pulled excessively.
the sharp edge, protect both parts with tube or tape.
NOT TO
PULL!
•If necessary, lock the wire harness properly. •When mounting parts, make sure that the wire harness
is not pressed by the parts.
•Do not twist the wire harness. •Wire the wire harness not to be pulled or expanded
when the handle is turned to the right or the left
completely. Avoid excessive bending or chewing and
interference with the engine.
•Prior to using the tester, please read the manual care- •Do not drop or throw the parts especially
fully and understand the contents. semiconductor contained parts because these parts may
•When testing the resistance of the tester, the zero be damaged by the impact of the drop.
adjustment must be performed before testing.
Is this
measurement range or
configuration in accord
with the manual?
1-8
SERVICE INFORMATION
SERIAL NUMBER LOCATION
KMYSE7ADS5C003019
ENGINE SERIAL NUMBER LOCATION FRAME SERIAL NUMBER LOCATION
1-9
SERVICE INFORMATION
MAINTENANCE INFORMATION
SPECIFICATIONS
TYPE OF VEHICLE a-Four FRAME TYPE UNDER BONE
OVERALL LENGTH 1,798mm BRAKING DISTANCE 8.0m(30km/h VELOCITY)
OVERALL WIDTH 683mm MIN. REVOLUTION RADIUS 1,800mm
OVERALL HEIGHT 1,107mm COOLING TYPE AIR-COOLED
WHEEL BASE 1,260mm STARTING STARTER MOTOR, KICK
MOTOR TYPE SJ50R MOTOR TYPE 2-CYCLE
DISPLACEMENT 49.5cc NO. OF CYLINDERS, MOUNTING 1 CYLINDER, TRANSVERSE
FUEL TYPE UNLEADED GASOLINE VALVE APPARATUS READ VALVE PISTON VALVE COMBINATION
FRONT AXLE 34kg BORE & STROKE 39.0X41.4mm
DRY WEIGHT REAR AXLE 58kg COMPRESSION RATIO 6.8:1
TOTAL 92kg MAX. OUTPUT 5.1PS/7,000rpm
PASSENGERS 2(65kg) MAX. TORQUE 0.42kgf·m/7,500rpm
FRONT AXLE 58.5kg PRIMARY SPEED REDUCTION RATIO 4.083
GROSS WEIGHT REAR AXLE 100.5kg SECONDARY SPEED REDUCTION RATIO 3.615
TOTAL 159kg TRANSMISSION GEARLESS TRANSMISSION
GROUND CLEARANCE 115mm

TRANSMISSION RATIO
CASTER 26。 0.76~2.41
1ST GEAR
TRAIL 80.5mm
MAINTENANCE SPECIFICATIONS
ITEM STANDARD USE LIMITS
LUBRICATION SYSTEM
ENGINE OIL TANK CAPACITY FULL CAPACITY 1.2 liters
RECOMMENDED ENGINE OIL DMC Ultra 2 super oil, 2-Cycle Oil
TRANSMISSION OIL CAPACITY FULL CAPACITY 0.09 liters
RECOMMENDED TRANSMISSION OIL DMC Pure Mission Oil or
SAE 80W/90
LUBRICATION TYPE Separation Lubrication

OIL FILTER TYPE Current Filtration,
OIL PUMP TYPE Plunger Type
COOLING TYPE
COOLING TYPE Air-Cooled
1-10
SERVICE INFORMATION
FUEL SYSTEM
FUEL TANK CAPACITY FULL CAPACITY 6ℓ -
AIR CLEANER TYPE Urethane Foam -
CARBURETOR SETTING MARK PB 11P -
VENTURI DIAMETER ր16mm -
AIR SCREW OPENING 1 1/4 Rotation -
FLOAT LEVEL 8.0mm -
IDLING RPMS 1,800±100rpm -
NO. OF JET NEEDLES 4 -
MAIN JET #65 -
SLOW JET #38 -
THROTTLE GRIP CLEARANCE 2-6mm -
CYLINDER HEAD, CYLINDER, PISTON

PORT OPEN/CLOSE PERIODS INHALATION OPEN Auto Control -
CLOSE Auto Control -
EXHAUST OPEN 81.5。BBDC -
CLOSE 81.5。ABDC -
SCAVENGING OPEN 56.5。BBDC -
CLOSE 56.5。ABDC -
CYLINDER HEAD COMPRESSION PRESSURE 10kgf/㎠-600rpm -
CYLINDER ID MARK LOCATION Side of Cylinder
INSIDE DIAMETER ID MARK(A) 39.000-39.005mm 39.05mm

NO ID MARK 39.005-39.010mm 39.05mm
CYLINDRICAL DEGREE - 0.10mm
OUT OF ROUNDNESS - 0.10mm
PISTON OUTSIDE DIAMETER MEASUREMENT LOCATION
OUTSIDE
DIAMETER
3mm
OUTSIDE DIAMETER ID MARK(A) 38.955-38.960mm 38.90mm
ID MARK(B) 38.965-38.970mm 38.90mm
NO ID MARK 38.960-38.965mm 38.90mm
CYLINDER AND PISTON CLEARANCE 0.035-0.050mm 0.10mm
PISTON PIN HOLE INSIDE DIAMETER 12.002-12.008mm 12.03mm
PISTON PIN OUTSIDE DIAMETER 11.994-12.000mm 11.98mm
PISTON AND PISTON PIN CLEARANCE 0.002-0.014mm 0.03mm
PISTON RING GAP TOP 0.10-0.25mm 0.40mm

SECOND 0.10-0.25mm 0.40mm
RING MARK Turning up -
CONNECTING ROD SMALL END PORTION DIAMETER 17.005-17.017mm 17.03mm
1-11
SERVICE INFORMATION
CLUTCH
CLUTCH AUTOMATIC Automatic Centrifugal -
TYPE Continuously Variable Transmission -
CLUTCH OUTER DIAMETER 107.0-107.2mm 107.5mm
CLUTCH LINING THICKNESS 3.0mm 2.0mm
DRIVE BELT WIDTH 17.5mm 16.5mm

MOVABLE DRIVE FACE
BUSH INSIDE DIAMETER 20.035-20.085mm 20.60mm
BOSS OUTSIDE DIAMETER 20.011-20.025mm 19.97mm
WEIGHT ROLLER OUTSIDE DIAMETER 15.920-16.080mm 15.40mm
DRIVEN PULLEY FACE SPRING FREE LENGTH 98.1mm 92.8mm

FACE OUTSIDE DIAMETER 33.965-33.985mm 33.94mm
MOVABLE FACE INSIDE DIAMETER 34.000-34.025mm 34.06mm
CRANK SHAFT
CRANK SHAFT LARGE END SIDE CLEARANCE 0.15~0.55mm 0.60mm

CONNECTING ROD LARGE END RIGHT
ANGLE DIRECTION CLEARANCE 0.010~0.02mm 0.04mm
CRANK SHAFT SHAKING A 0.03mm(70mm from center) 0.15mm
B 0.05mm(40mm from center) 0.10mm
FRONT, REAR WHEELS

WHEELS RIM RUNOUT RADICAL - 2.0mm
AXIAL - 2.0mm
AXLE DEFLECTION - 0.2mm
TIRES TYPE TUBELESS -
TIRE PRESSURE FRONT 1.75㎏f/㎠ (1.75㎏f/㎠) -
(2 PERSON) REAR 2.00㎏f/㎠ (2.25㎏f/㎠) -
TIRE SIZE FRONT 120/70-12 58L -
REAR 130/70-12 62L
BRAKES
FRONT BRAKE LEVER FREE PLAY 10~20mm -
BRAKE FLUID DOT3 or DOT4 -
BRAKE PAD THICKNESS - to wear line
DISK THICKNESS 3.5mm 3.0mm
DISK SHAKING - 0.3mm
DISK WEAR LINE 3.0mm
MASTER CYLINDER INSIDE DIAMETER 12.740-12.743mm 12.755mm
MASTER PISTON OUTSIDE DIAMETER 12.657-12.684mm 12.645mm
CALIPER CYLINDER INSIDE DIAMETER 33.960-34.010mm 34.02mm
CALIPER PISTON OUTSIDE DIAMETER 33.878-33.928mm 33.87mm
REAR BRAKE LEVER FREE PLAY 10~20mm -
DRUM INSIDE DIAMETER 110mm 111mm
LINING THICKNESS 4.0mm 2.0mm
SUSPENSION
FRONT FRONT CUSHION FREE LENGTH 278.6mm -
REAR REAR CUSHION FREE LENGTH 220.6mm -
1-12
SERVICE INFORMATION
IGNITION SYSTEM
SPARK PLUG STANDARD BR8HSA

PLUG GAP 0.6~0.7mm
IGNITION TIMING F MARK BTDC 17。 ±2。
/1,800rpm
PEAK VOLTAGE IGNITION COIL(PRIMARY VOLTAGE) over 120V
EXCITE COIL over 120V
PULSE GENERATOR over 1.5V
IGNITION COIL RESISTANCE VALUES(20℃)
PRIMARY COIL 0.1-0.5Ω
SECONDARY COIL(PLUG CAP CONNECTION) ㏀
6.5-9.5㏀
SECONDARY COIL(PLUG CAP DISCONNECTION) 2.6±1.25㏀㏀
EXCITE COIL RESISTANCE VALUE(20℃) 500Ω±20%
PLUSE GENERATOR RESISTANCE VALUE(20℃) 100Ω±20%
CHARGING SYSTEM, AC GENERATOR
AC GENERATOR TYPE AC
OUTPUT 12V-9.5A/5,000rpm
CHARGING COIL RESISTANCE VALUE(20℃) 0.8Ω±20%
LIGHTING COIL RESISTANCE VALUE(20℃) 0.55Ω±20%
REGULATOR/RECTIFIER TYPE Semi-conductor
CONTROL VOLTAGE LAMP SIDE 12.6-13.6V/5,000rpm
CHARGING SIDE 14.0-15.0V/5,000rpm
REGISTER RESISTANCE VALUE REGISTER(6.7Ω 5W) 6.3-7.1Ω
REGISTER(5.9Ω 30W) 5.5-6.5Ω
LIGHTS, METER, SWITCHES
LIGHTS, BULBS HEADLIGHT 12V-35/35W

TAIL/STOP LIGHT 12V-5/21W
WINKER LIGHTS FRONT 12V-10W×2
REAR 12V-10W×2
METER LIGHTS 12V-1.7W
HIGH BEAM PILOT 12V-3W
OIL PILOT 12V-3W
WINKER PILOTS 12V-3W
FUSE 7A
LICENSE LAMP 12V-5W
BATTERY
TYPE MF BATTERY
CAPACITY 12V-3AH
TERMINAL VOLTAGE(20℃) 13.0-13.2V
CHARGING CURRENT/STANDARD 0.4A/5h
CHARGING CURRENT/RAPID 4A/0.5h
1-13
SERVICE INFORMATION
TWIST TORQUE
STANDARD TWIST TORQUE
TYPE TWIST TORQUE TYPE TWIST TORQUE
5mm BOLT, NUT 0.5㎏f·m 5mm SCREW 0.4㎏f·m
6mm BOLT, NUT 1.0㎏f·m 6mm SCREW 0.9㎏f·m
8mm BOLT, NUT 2.2㎏f·m 6mm SCREW FLANGE BOLT, NUT 1.2㎏f·m
Bolts not appearing in the following table are tightened using standard torque.
ENGINE PARTS
TWIST PART NUMBER SCREW DIAMETER (mm) TWIST TORQUE REFERENCE

FLY WHEEL NUT 1 10 4.0㎏f·m
DRIVE FACE NUT 1 12 5.5㎏f·m
CYLINDER HEAD BOLT 4 6 1.0㎏f·m
SPARK PLUG 1 14 1.4㎏f·m
DRIVEN FACE NUT 1 28 5.5㎏f·m
CLUTCH OUTER NUT 1 10 4.0㎏f·m
OIL LEVEL CHECK BOLT 1 8 1.3㎏f·m
EXHAUST PIPE JOINT NUT 2 6 1.2㎏f·m
MUFFLER BRACKET BOLT 2 8 3.3㎏f·m
CRANK CASE BOLT 6 6 1.0㎏f·m
1-14
SERVICE INFORMATION
FRAME PARTS
TWIST PART NUMBER SCREW DIAMETER TWIST TORQUE REFERENCE
STEERING STEM LOCK NUT 1 - 7.0㎏f·m
HANDLE POST TWIST NUT 1 10 5.0㎏f·m
FRONT BRAKE LEVER PIVOT BOLT 1 6 1.0㎏f·m
FRONT BRAKE LEVER PIVOT NUT 1 6 1.0㎏f·m
REAR BRAKE LEVER PIVOT SCREW 1 5 0.3㎏f·m
REAR BRAKE LEVER PIVOT NUT 1 5 0.4㎏f·m
MASTER CYLINDER HOLDER BOLT 2 6 1.2㎏f·m
MASTER CYLINDER COVER SCREW 2 4 0.2㎏f·m
BRAKE HOSE BOLT 2 10 3.5㎏f·m
CALIPER MOUNT BOLT 2 8 2.7㎏f·m
CALIPER BREATHER VALVE 1 8 0.6㎏f·m
CALIPER PAD PIN 2 10 1.8㎏f·m
CALIPER SLIDE PIN BOLT 1 8 2.3㎏f·m
BRAKE SWITCH SCREW 1 4 0.12㎏f·m
STEERING STEM BOLT(FRONT FORK SIDE) 4 10 3.5~4.5㎏f·m
FRONT AXLE NUT 1 12 6㎏f·m
REAR AXLE NUT 1 14 11.0㎏f·m
SPEEDOMETER CABLE SETTING SCREW 1 4 0.2㎏f·m
REAR BRAKE ARM BOLT 1 6 0.6㎏f·m
FRONT BRAKE DISK BOLT 3 8 3.9㎏f·m
REAR CUSHION UPPER BOLT 1 10 4.0㎏f·m
REAR CUSHION LOWER BOLT 1 10 4.0㎏f·m
ENGINE HANGER BRACKET NUT 2 10 5.0㎏f·m
EXHAUST PIPE JOINT NUT 3 6 1.2㎏f·m
MUFFLER BRACKET BOLT 2 8 3.3㎏f·m
EXHAUST PIPE PROTECTOR SCREW 4 6 0.5㎏f·m
1-15
SERVICE INFORMATION
SPECIALIZED TOOLS
TOOL NAME TOOL NO. USAGE CHAPTER

FLOAT LEVEL GAUGE 07401-001000 Carburetor Oil Level Measurement 5
BEARING DIRVER 07945-GC80000 Change of Driven Face Outer Bearing
BEARING REMOVER 07936-3710300 Disassembly of Driven Face Needle Bearing
REMOVER HANDLE 07936-3710100
REMOVER WEIGHT 07741-0010201
DRIVER HANDLE A 07749-0010000 Assembly of Driven Face Needle Bearing 7
OUTER DRIVER 24×26mm 07746-0010700
CLUTCH SPRING COMPRESSOR 07960-KM10000 Disassembly/Assembly of Clutch/Driven Face
SOCKET WRENCH 39mm 0723-03900
CLUTCH CENTER HOLDER 07724-0050001 Disassembly/Assembly of Driven Pulley/Driven Face
UNIVERSAL HOLDER 07725-0030000 Disassembly/Assembly of Clutch/Driven Pulley
CRANK ASSEMBLY 0740-00001 Assembly of Drive Shaft
DRIVER HANDLE A 0749-0010000 Assembly of Drive Shaft Bearing
OUTER DRIVER 37×40mm 07746-0010200
DRIVER PILOT, 17mm 07746-0040400
UNIVERSAL BEARING PULLER 0755-00001 Disassembly of Crank Shaft Bearing
9
CRANK CASE PULLER 0751-00003 Disassembly of R/L Crank Case, Crank Shaft
CRANK ASSEMBLY 0740-00001 Disassembly of R.Crank Case, Crank Shaft
OUTER DRIVER 52×55mm 07746-0010400 Assembly of Crank Shaft Bearing
DRIVER PILOT 20mm 07746-0040500
DRIVER HANDLE A 07749-0010000
CRANK ASSEMBLY 0740-00001 Assembly of R/L Crank Shaft Oil Seal
LOCK NUT WRENCH A 07916-1870101 Disassembly of Top Cone Race
LOCK NUT WRENCH B 07916-KM10000
BALL RACE REMOVER 07946-GA70000 Assembly of Ball Race 10
OUTER DRIVER, 42×47mm 07746-0010300
DRIVER HANDLE A 07749-0010000
SHOCK ABSORBER COMPRESSER 07GM-0010000 Disassembly/Assembly of Rear Cushion
COMPRESSER SCREW ASS’
Y 079GME-0010100 11
SPRING COMPRESSER ATTACHMENT 07967-GA70102
SPRING COMPRESSER ATTACHMENT 07JME-GW20100
UNIVERSAL HOLDER 07725-0030000 Disassembly/Assembly of Fly Wheel
13
A.G.G ROTOR PULLER 0750-00006 Disassembly of Fly Wheel
1-16
SERVICE INFORMATION
LUBRICATION OIL
ENGINE PARTS
APPLICATION AREAS CAUTIONARY SUGGESTIONS OIL TYPE
CRANK CASE JOINING FACE Gasket Fluid(TB 1215)
CRANK CASE REVOLUTION PART Ultra-2 Super, 2-Cycle Oil
CYLINDER BIG REVOLUTION PART, FRICTION PART (Separation Lubrication Use)
TRANSMISSION(FINAL REDUCTION) Capacity : 0.09ℓ SAE 80W/90
KICK SPINDLE BUSH
STARTER PINION
STARTER DRIVE GEAR OPERATION PART Capacity : 5.0~5.6g Multi-Purpose Grease
MOVEABLE DRIVEN FACE
(DRIVEN FACE OPERATION PART)
OIL PUMP DRIVE GEAR Molybdenum Grease
FRAME PARTS
APPLICATION AREAS CAUTIONARY SUGGESTIONS OIL TYPE
FRONT WHEEL DUST SEAL EDGES Multi-Purpose Grease
FRONT PIVOT ARM BUSH FRICTION FACE
FRONT PIVOT ARM SEAL EDGES
REAR BRAKE CAM AXLE PART, CAM PART
WHOLE AREA OF REAR BRAKE CAM DUST SEAL
REAR BRAKE ANCHOR PIN AXLE PART
FRONT BRAKE OIL SEAL EDGES
FRONT BRAKE CAM AXLE PART, CAM PART
WHOLE AREA OF FRONT BRAKE CAM DUST SEAL
SPEEDOMETER GEAR/PINION INSIDE DIAMETER
PART, AXLE PART, GEAR TEETH PART
BALL RACE, BEARING REVOLUTION PART
HANDLE GRIP INSIDE AXLE PART Adhesives ROYAL BOND 1300
1-17
SERVICE INFORMATION
SYMBOLS
The following symbols appear in this manual and offer cautionary suggestions which need to be heeded when performing
maintenance work on the vehicle.
SYMBOL CAUTION SYMBOL CAUTION

Indicates an important step or operation.
Indicates special caution needed. CAUTION Possibility of resulting in minor
WARNING Possibility of resulting in serious malfuctioning or damage to part if ignored.
malfuctioning of vehicle if ignored. Indicates general caution. Caution needed to
NOTE be taken when performing the maintenance
operation or in the handling of part.
The following symbols indicate needed lubrication steps, the changing of parts, and required specialized tools, etc. when
performing maintenance.
SYMBOL CAUTION
Indicates needed application of oil. When a designated brand is not listed, use the designated or
suggested engine oil when this symbol appears.
Indicates needed application of a molybdenum solution. The molybdenum solution is made by
mixing molybdenum grease with engine oil at a 1:1 ratio.
Indicates needed application of a multi purpose grease. (NLG 1 #2 using a lithium soap base)
Example brand: Shell Albania EP-2(Fire-proof Shell Oil)
Indicates needed application of molybdenum grease.
(containing over 3% of emulsified molybdenum, NCG 1 #2)
Indicates needed application of molybdenum paste.
(containing over 40% of emulsified molybdenum, NLG 1 #2)
Indicates needed application of silicon grease.
Indicates needed application of an antilock substance.

When a designated brand is not listed, use a medium-strength brand.
Indicates needed application of a sealant.
Indicates new part needed every time when disassembled.
Indicates brake fluid needed. Use recommended DOT3 or DOT4 brake fluid.
Use recommended cushion oil.
Use Specialized Tool.
Use Option Tool. These tools are needed for the part, see part list for tool number.
( 3-1) Indicates reference page. This particular symbol indicates chapter 3 page 1.
Special grease, etc. that do not correspond to the above are indicated without using symbols.
1-18
SERVICE INFORMATION
WIRING DIAGRAM
LIGHTING SW. CORD

LIGHTING, START SW. CORD RR. STOP SW. CORD
FR. BRAKE HOSE
FR. BRAKE HOSE
FR. WINKER LIGHT CORD THROTTLE CABLE
RR. BRAKE CABLE
SPEEDOMETER CABLE
SPEEDO METER CORD FR. WINKER LIGHT CORD
30 WINKER SW. CORD PILOT BOX CORD
VIEW X
SPEEDOMETER CABLE
FR. BRAKE HOSE SPEEDOMETER ASS'Y
SPEEDOMETER CORD
FR. WINKER LIGHT CORD FR. WINKER LIGHT CORD
LIGHTING START SW. CORD RR. BRAKE CABLE
FR. STOP SW. RR. STOP SW. CORD
LIGHTING START SW. WINKER SW. CORD
WINKER SW. ASS'Y
THROTTLE CABLE FR. WINKER ASS'Y
GREASE
HORN COMP.
HEADLIGHT COUPLER INNER COVER
SEAT LOCK CABLE
COMB. & LOCK SW. CLIP CLAMPER
FRAME EARTH
REGULATE RECTIFIER RESISTOR
RESISTOR CORD FR. BRAKE HOSE
SPEEDOMETER CABLE
WIRE HARNESS
1-19
SERVICE INFORMATION
WINKER REALY, ASS’Y
WIRE HARNESS COUPLER

HEAD LIGHT ASS’Y
HEAD LIGHT REAR WIRING DETAIL
FUEL UNIT
SEAT LOCK CABLE
FUEL AUTO COCK ASS’Y
FUEL VENT TUBE AUTO BY STARTER CORD
THERMOSTAT SW. CORD
SPEEDOMETER ASS’Y
FUEL TUBE
OIL TUBE
OIL PASS TUBE
THROTTLE CABLE
OIL PUMP CABLE
LICENSE LAMP
LICENSE LAMP COUPLER HORN COMP.
TAIL & STOP, RR. WINKER RESISTOR
R/L COUPLER AUTO BY STARTER 5W 6.7
FUEL UNIT COUPLER COMB. & LOCK SW
CDI UNIT
THERMOSTAT SW.
STARTER REALY, ASS’Y WIRE HARNESS
IG COIL
FR. BRAKE HOSE
ACG. CORD COUPLER
SECODARY AIR FILTER ASS’Y
HIGH TENSION CORD

SIDE STAND SW. COUPLER
SPARK PLUG CAP ASS’Y BATTERY ASS’Y
SPEEDOMETER CABLE
1-20
SERVICE INFORMATION
HORN COMP. COMB. & LOCK SW.

WINKER REALY, ASS’Y WIRE HARNESS CLIP
SEAT LOCK CABLE

HEAD LIGHT ASS’Y
FR. BRAKE HOSE

FR. WINKER CORD
RR. BRAKE CABLE SPEEDO METER CORD
THROTTLE CABLE RR. STOP SW. CORD
LIGHTING SW. CORD
PILOT BOX CORD COUPLER
WIRE FRONT WIRING DETAIL
STARTER REALY, ASS’Y
CDI UNIT, ASS’Y

AUTO BY STARTER COUPLER THERMOSTAT SW.
SPEEDOMETER ASS,Y IG COIL
LIGHTING START SW. CORD ACG. CORD COUPLER OIL LEVEL S/W
WIRE HARNESS OIL TANK
LIGHTING START SW.
SECONDARY
AIR FILTER ASS’Y FUEL VENT TUBE
HIGH TENSION CORD
FR. WINKER CORD

PILOT BOX RR. BRAKE CABLE
FR. BRAKE HOSE
LICENSE LAMP
SPEEDOMETER CABLE
SPEEDOMETER CORD FUEL TANK
HEAD LIGHT COUPLER FUEL UNIT
RESISTOR FR. WINKER CORD
AUTO BY STARTER 5W 6.7 SPEEDO METER CORD
WINKER REALY, ASS’Y RR. STIOP SW. CORD FUEL VENT TUBE
RESISTOR LIGHTING SW. CORD FUEL STRAINER
PILOT BOX CORD
HEAD LIGHT ASS’Y COUPLER SEAT LOCK CABLE
OIL STRAINER JOINT
CABLE CLIP
FR. BRAKE HOSE
OIL TUBE
SPEEDOMETER CABLE THERMOSTAT SW. CORD
AUTO BY STARTER CORD
FUEL TUBE
THROTTLE CABLE
AIR VENT TUBE
OIL PUMP CABLE

OIL PASS CABLE
THROTTLE CABLE JUNCTION
RR. BRAKE CABLE
BATTERY ASS,Y SPARK PLUG CAP ASS’Y
THROTTLE CABLE
SEAT LOCK CABLE SIDE STAND SW.
RR. BRAKE CABLE
FR. BRAKE HOSE

FR. BRAKE CALIPER
1-21
SERVICE INFORMATION
RESISTOR REGULATE RECTIFIER

AUTO BY STARTER 5W 6.7
HEAD LIGHT COUPLER
HORN COMP.
SPEEDOMETER CABLE
FR. BRAKE HOSE
RR. BRAKE CABLE
SEAT LOCK CABLE BATTERY

THROTTLE CABLE FUSE CASE
RR. BRAKE CABLE WIRE HARNESS
SPARK PLUG CAP
SIDE STAND SW.

COUPLER
SIDE STAND SW.
THROTTLE CABLE JUNCTION
HIGH TENTION CORD

SECONDARY AIR FILTER ASS’Y
OIL PUMP CABLE
IG COIL
THROTTLE CABLE
ACG. CORD COUPLER
OIL PASS TUBE
STARTER REALY, ASS’Y
THERMOSTAT SW.
OIL LEVEL S/W
CDI UNIT
FUEL TUBE
OIL TUBE FUEL UNIT COUPLER
THERMOSTAT SW. CORD
LICENSE LAMP COUPLER
AUTO BY STARTER CORD
TAIL & STOP, RR. WINKER R/L
SEAT LOCK CABLE
LICENSE LAMP
FUEL UNIT
FUEL VENT TUBE
1-22
2. INSPECTIONS/ADJUSTMENTS
SERVICE INFORMATION 2-1 BRAKE FLUID 2-6

REGULAR INSPECTION SCHEDULE 2-2 BRAKE PAD/SHOE 2-7
FUEL LINE (FUEL TUBE) 2-3 BRAKE SYSTEM 2-7
2
FUEL LINE FOR CLOGGING 2-3 HEADLIGHT ADJUSTMENT 2-8
THROTTLE GRIP OPERATION 2-3 SIDE STAND 2-8
AIR CLEANER 2-4 SUSPENSION 2-9
SPARK PLUG 2-5 BOLTS, NUTS, FASTENERS 2-9
CYLINDER COMPRESSION PRESSURE 2-5 WHEELS/TIRES 2-9
CARBURETOR IDLING 2-6 STEERING HEAD BEARING 2-10
AIR SCREW ADJUSTMENT 2-6 BATTERY 2-10
SERVICE INFORMATION
•The exhaust gas contains poisonous substance. Do not keep engine idling in a closed or poorly ventilated place for a
long period of time.
•Erect the main stand prior to beginning work.
SPECIFICATIONS
ITEM STANDARD VALUE REFERANCE
THROTTLE GRIP FREE PLAY 2-6mm
SPARK PLUG BR8HSA
SPARK PLUG GAP 0.6〜0.7mm
CARBURETOR IDLE SPEED 1,800±100rpm
CYLINDER COMPRESSION PRESSURE 10㎏f/㎠ - 600rpm
TORQUE VALUES
SPARK PLUG 1.4㎏f·m
CYLINDER HEAD COVER BOLTS 1.0㎏f·m
2-1
INSPECTIONS/ADJUSTMENTS
REGULAR INSPECTION SCHEDULE

Carry out pre-operation check at each scheduled maintenance period based on the information described in the owner’s
manual.
I : INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY.
R : REPLACE L : LUBRICATE C : CLEAN
ODOMETER READING(NOTE 1)
FREQUENCY
x 1000Km 1 4 8 12 REMARK
ITEM
MONTH 6 12 18
＊ FUEL LINE(FUEL TUBE) I I I
＊ THROTTLE GRIP OPERATION I I I I
OIL PUMP, OIL LINE I I I
AIR CLEANER C C C
SPARK PLUG I I I NOTE 2
CARBON REMOVAL Every 8,000㎞ : C
＊ CARBURETOR IDLE SPEED I I I I
＊ TRANSMISSION OIL R
BRAKE SHOE/PAD WEAR I I I
BRAKE SYSTEM I I I I NOTE 3
＊ BRAKE STOP SWITCH I I I
＊ HEADLIGHT ADJUSTMENT I I I
CLUTCH SHOE WEAR I I I
＊ SUSPENSION I I I
＊ BOLTS, NUTS, FASTENERS I I
WHEELS/TIRES I I I
STEERING HEAD BEARING I I
＊ DRIVE BELT I I I
＊ WEIGHT ROLLER I I I
＊ SLIDE PIECE I I I
＊ If there are no appropriate type of tools and maintenance data available, or if you do not have mechanical technology
contact authorized maintenance shops, dealers or other designated repair shops for maintenance and inspections.
To ensure safety, inspections and maintenance of these parts must be carried out by authorized maintenance shops,
dealers or registered repair center.
NOTE
1. After the odometer reading exceeds 12,000km, repeat maintenance service at intervals indicated in the table.
2. After riding in areas with high humidity or pollution, carry out maintenance service more frequently.
3. Replace every 2 years. Proper technology is required for this job.
2-2
LUGGAGE
LUGGAGE BOX
LUGGAGE BOX
BOX FUEL LINE(FUEL TUBE)
● Remove the luggage box.( 3-3)
● Check the fuel tube of the fuel auto cock connected to
the fuel tank and carburetor. If the fuel tube is cranked,
damaged or leaks, replace it.
FUEL
FUEL
FUEL TANK
TANK
TANK FUEL LINE FOR CLOGGING
•Refer to section 2 for fuel filter inspection.
● Check the fuel tank cap and/or fuel tank breather tube
for clogging.
● Visually inspect the fuel strainer for contamination.
FUELTUBE
FUELTUBE
FUELTUBE Check the fuel flow with the fuel strainer installed and
with the strainer removed.
Replace the fuel strainer if it is excessively contaminated
or if the fuel flow is not smooth.
FUEL
FUEL
FUEL STRAINER
STRAINER
STRAINER
FUEL AUTO
FUEL
FUEL AUTO COCK
AUTO COCK
COCK
•Note the installation direction of the fuel strainer. Be

sure to install it as shown in the drawing, i.e., with
the cup facing down. Fuel flows even though the
strainer is installed upside down, but it contaminates
the inner wall of the strainer and prevents visual
inspection of the strainer.
● Remove the fuel valve lock nut and check the fuel
(Inner walls get
contaiminated, strainer screen for contamination. Tighten the lock nut
making visual to the specified torque.
inspection
difficult.)
THROTTLE GRIP OPERATION

● Check if the throttle grip operates smoothly in any
steering position
● If the throttle grip does not operate properly, lubricate
the throttle cable.
● If the throttle grip does not operate properly, check the
throttle cable for aging, damage or kinking.
● Check the throttle grip free play.
FREE PLAY : 2~6mm
2-3
● For adjustment, loosen the lock nut and turn adjuster.
● After adjusting, tighten lock nut. After adjustment is
completed, recheck the throttle grip free play.
LOCK
LOCK
LOCK NUT
NUT
NUT
ADJUSTER
ADJUSTER
ADJUSTER
AIR CLEANER COVER AIR CLEANER

● Loosen the 5 setting screw assembled to the air cleaner
case cover, and then remove the air cleaner case cover.
WASHER SCREW ● Remove the air cleaner element.

● Wash away any accumulated dust or dirt, by gently
squeezing it in non flammable or high flash point
solvent.
•Using gasoline or low flash point solvents for

cleaning parts may result in a fire or explosion.
•Cleaning the element with gasoline or any acid,

alkaline, or organic, volatile type oil may cause
improper ignition, deterioration of the element, or a
loosening of the element adhesive.
AIR CLEANER ELEMENT
● Be sure to allow the element to dry thoroughly before
applying oil. Otherwise, the oil will be diluted by the
and the filtering ability of the filter will be much
less effective.
● Spread clean #80~90 gear oil on the element, rubbing
inthoroughly over the surface with both hands, and then
squeeze out any excess oil.
•Using air filter oil when riding in extremely dusty

conditions prevents premature engine wear due to
dust/dirt drawn into the engine. Apply air filter oil to
the entire surface of the element and rub it with both
hands to saturate the element with oil. Squeeze out
excess oil.
2-4
SPARK PLUG
● Remove the plug maintenance cover.
● Remove the spark plug cap and disassemble the plug.
PLUG MAINTENANCE COVER

SPARK PLUG CAP
● Check the plug for damage, contamination or deposits.
● If the spark plugs are severely contaminated or
damaged, raplace with new ones. If the plugs can be
reused after removing only the carbon, use plug cleaner
and wire brush to clean the plugs.
● Always use a feeler gauge to check the gap.
SPARK PLUG GAP : 0.6~0.7mm
•Make sure there is no dirt or debris on the seat of the

spark plug hole before inserting the spark plug.
•To prevent damage to the cylinder head, hand-tighten
the spark plug before using a wrench to tighten to the
specified torque.(torque : 14kgf·m)
•Do not overtighten the spark plug.
COMPRESSION GAUGE
CYLINDER COMPRESSION PRESSURE

● Start and warm up the engine.
● Remove the plug maintenance cover.
● Stop engine, and remove the spark plug cap and spark
plug.
● Install a compression gauge.
● Open the throttle completely, and crank the engine with
the starter motor until the gauge reading rising.
•The maximum reading is usually reached within 4~7

seconds.
COMPRESSION PRESSURE : 10kg/cm2 (600rpm)
● If the pressure is low, check the following:

-Leakage from the cylinder head gasket
-Piston/cylinder worn
● If pressure is high, check the following:
-Carbon deposits on the piston head, and cylinder head.
TOOL : COMPRESSION GAUGE
2-5
CARBURETOR IDLING
● Stand the vehicle on the main stand.
● Heat the engine to make accurate idling inspection and
adjustment.
● Verify all engine adjustments satisfy specifications.
Make adjustments, if necessary.
● Turn the throttle stop screw and make adjustments to
prescribed idling speed.
THROTTLE STOP SCREW
AIR SCREW ADJUSTMENT

THROTTLE STOP SCREW
•The air screw is factory pre-set. Adjustment is not

necessary unless the carburetor is overhauled or a
new air screw is installed.
•Tightening the air screw against its seat will damage
the seat.
AIR SCREW
● Turn the air screw clockwise until it seats lightly then
back it out to the specification given. This is an initial
setting prior to the final air screw adjustment.
● Rev the engine up slightly from the idle speed and
make sure that engine speed rises and returns smoothly.
● Adjust by turning the air screw in or out within a 1/4
turn if necessary. If the engine cannot be adjusted by
turning the air screw within a 1/4 turn, check for other
engine problems.
•Excessive air screw adjustment may cause the engine

sticking and deteriorate the starting performance.
BRAKE FLUID
● Remove the brake fluid cover.
● Check the oil level inside the front brake reservoir. If
the oil level is near the lower limit line, remove the
reservoir diaphragm and fill DOT 3 and DOT 4 brake
BRAKE
BRAKE
BRAKE HOSE
HOSE
HOSE BOLT
BOLT
BOLT MASTER
MASTER CYLINDER
MASTER CYLINDER
CYLINDER fluid to the top limit line.
● If the brake fluid reaches the lower limit line, check the
entire brake system for leaks.
•Brake fluid will damage painted, plastic or rubber

parts.
•Mixing incompatible fluids can impair braking
efficiency.
•Foreign materials can clog the system, causing a
reduction or complete loss of braking ability.
•A leak in the brake system can lead to reduced
braking effiency and possible loss of braking ability.
2-6
BRAKE PAD/SHOE
BRAKE PAD REPLACEMENT
● Check the brake pads for wear.
● If the red mark on the pad reaches the brake disc,
replace the pads.
RED MARK
•Replace the brake pads in sets.
BRAKE SHOE REPLACEMENT

● If the arrow mark of the wear limit aligns with the ‘△’
mark when the rear brake lever is fully pressed, it
MARK indicates the brake lining has reached the service limit.
Replace the brake shoes.
BRAKE
BRAKE
BRAKE HOSE
HOSE
HOSE BRAKE SYSTEM
● Check the front brake hose for cracks or damage. If any
leaks are found, replace immediately.
● Check the brake rod for looseness or damage, and
replace it if necessary.
BRAKE
BRAKE CALIPER
BRAKE CALIPER
CALIPER
BRAKE LEVER FREE PLAY

● Check the free play after pulling the lever.
FRONT : 10~20mm
REAR : 10~20mm
FREE PLAY
2-7
REAR BRAKE FREE PLAY ADJUSTMENT
● Turn the adjuster nut to adjust the free play.
● After initial adjustment, check the operation of the rear
brake light switch. Make additional adjustments, if
necessary.
ADJUSTER NUT
HEADLIGHT ADJUSTMENT
● Adjust the headlight beam level by operating the
adjusting screw located on the upper side of the front
fender.
•Adjust the beam level according to local laws and

regulations.
•Improper beam level adjustment may blind
oncoming drivers, or may incorrectly light the road
ADJUSTER LEVER
ADJUSTER
ADJUSTER LEVER
LEVER ahead.
SIDE STAND
● Erect the main stand.
SIDE STAND SPRING
● Pull the lower end of the side stand, and see if it moves
freely.
● If the side stand does not move smoothly, apply grease
to the pivot area.
● If the side stand moves too freely, check the side stand
spring.
● Check the axial movement of the side stand.
● Check the side stand ignition cut-off switch :

-Put the side stand up.
-Start the engine.
-Lower the side stand. The engine should stop as you
put the side stand down.
● If there is a problem with the system, check the side
stand switch.
2-8
SUSPENSION
•Do not ride motor cycle with an unsatisfactory

suspension. Loose or worn suspension parts will lead
to deterioration in the vehicle’s safety and operation
efficiency.
FRONT WHEEL
● Hold the brake lever, and compress the front cushion
up and down several times to check the operating
conditions.
● Check the front fork for oil leakage, parts damage or
looseness.
REAR WHEEL
● Compress the near cushion up and down several times
to check the operating conditions.
● Check the rear fork for oil leakage, parts damage or
looseness.
BOLTS, NUTS, FASTENERS

● Check all nuts and bolts of the frame during the regular
maintenance to check if they meet the prescribed
torque value.
● Check all pins, clips, hose clamps and cable stays.
WHEELS/TIRES
•Check the tire pressure when the tires have been

cooled off. Check the tread (the part making contact
with the road surface) and side for wear, cracks or
damage. Replace damaged tires.
STANDARD PRESSURE
f/ (kpa)
ITEM FRONT WHEEL REAR WHEEL
TIRE PRESSURE GAUGE DRIVER ONLY 1.75(175) 2.00(200)
DRIVER AND A PASSENGER 2.00(200) 2.25(225)
2-9
● Check the tread depth at the tire center.
● If the tread depth has reached the service limit, replace
the tire.
SERVICE LIMIT : 4.0mm
7.5mm
STEERING HEAD BEARING
•Check the cable if it interferes with the handle

operation.
● Lift the front wheel and check if the handle moves right
and left smoothly. If the handles move heavily, check if
the cable or electric cord interferes with the handle. If
the hadle moves satisfactorily, adjust the steering head
bearing.
BATTERY
BATTERY COVER ● Remove a tapping screw securing the battery cover
from the floor panel.
● Check if the terminal is loose.
● If the terminal is loose, check and clean the contacting
surface and then tighten it.
● Apply grease thinly after tightening.
● If the terminal is rusted, remove the battery, pour warm
TAPPING SCREW water and clean with the wire brush.
- FULL CHARGING VOLTAGE : 13.0~13.2V

- LOW CHARGING VOLTAGE : LESS THAN 12.3V
•Check the charging condition using the voltmeter.

•Pay attention not to transform the battery terminal.
•Never remove the filler cap.
DIGTAL TESTER
2-10
3. EXTERNAL PARTS
SERVICE INFORMATION 3-1 ENGINE HANGER SIDE COVER 3-5

MAINTENANCE PRECEDURE 3-2 FRONT COVER 3-5
LUGGAGE BOX 3-3 FRONT FENDER 3-5
PLUG MAINTENANCE INNER COVER 3-5
COVER/CENTER COVER 3-3 FRONT UNDER COVER 3-6 3
REAR CARRIER 3-3 MUFFLER 3-6
BODY COVER 3-3 REAR FENDER 3-7
TAILLIGHT BASE 3-4 REAR WHEEL MUD GUARD 3-8
FLOOR SIDE COVER 3-4 UNDER COVER 3-8
FLOOR PANEL 3-4
SERVICE INFORMATION
● This section describes external parts removal/installation.

● Do not apply unreasonable force when disassembling covers, to prevent possible damage.
● A muffler is hot. Do not service it immediately after the engine is stopped.
3-1
EXTERNAL PARTS
MAINTENANCE PROCEDURE
NAMES OF FRAME COVERS
10 4
1
5
11 12
8 3
2 6
13
7 9
● This chart shows arrows connected in the order of disassembling covers.
① LUGGAGE BOX ⑦ FLOOR SIDE COVER ⑩ FRONT COVER
② PLUG MAINTENANCE ⑧ FLOOR PANEL ⑪ FRONT FENDER

COVER
③ CENTER COVER ⑨ ENGINE HANGER ⑫ INNER BOX

SIDE COVER
④ REAR CARRIER ⑬ FRONT UNDER

COVER
⑤ BODY COVER
⑥ TAILLIGHT BASE
3-2
EXTERNAL PARTS
LUGGAGE BOX
● Release the seat lock using the main key to open the
seat.
● Loosen 4 washer bolts and 2 flange bolts.
● Remove the oil tank cap and the fuel tank cap.
FLANGE
FLANGE BOLT
FLANGE BOLT
BOLT
•Luggage box can be removed with the seat.
● Remove the luggage box.

● Install in the reverse order of removal.
•Install the oil tank cap and the fuel tank cap
PLUG
PLUG
PLUG MAINTENANCE
MAINTENANCE
MAINTENANCE COVER
COVER
COVER temporarily to prevent the foreign material from
entering after removing the luggage box.
PLUG MAINTENANCE COVER/CENTER COVER

● Release the seat lock using the main key to open the
seat.
● Loosen the washer bolt securing the luggage box.
SCREW
SCREW
SCREW ● Loosen the special screw to remove the plug
maintenance cover.
● Loosen 2 tapping screw securing the floor panel.
● Loosen 2 special screw (R/L) securing the body cover.
● Remove the center cover.
•If removal is difficult, recheck each connection and

then try removing again.
REAR CARRIER
● Loosen 3 special bolts securing the top of the body
cover.
● Remove the rear carrier.
SPECIAL
SPECIAL
SPECIAL BOLT
BOLT
BOLT
•Pay attention not to break of damage the rear carrier
when installing or removing.
BODY COVER
● Remove the luggage box. ( 3-3)
● Remove the center cover. ( 3-3)
● Remove the rear carrier. ( 3-3)
● Loosen 2 special screw (R/L) securing the frame body.
● Loosen 2 body cover clip (R/L) securing the tail light
base.
● Remove the body cover.
BODY
BODY COVER
BODY COVER
BODY CLIP
COVER CLIP
COVER CLIP
CLIP ● Install in the reverse order of removal.
SPECIAL
SPECIAL
SPECIAL SCREW
SCREW
SCREW
3-3
EXTERNAL PARTS
WASHER
WASHER BOLT
WASHER BOLT
BOLT TAILLIGHT BASE
● Remove
- Luggage box. ( 3-3)
- Center cover. ( 3-3)
- Rear carrier. ( 3-3)
- Body cover. ( 3-3)
● Loosen 2 washer bolt securing the frame.
● Loosen 2 body cover clip securing the rear fender.
● Disconnect the taillight wiring.
● Remove the taillight base.
TAILLIGHT
TAILLIGHT BASE
TAILLIGHT BASE
BASE
FLOOR SIDE COVER

● Loosen the 2 washer screw located in the side of the
R,L floor side cover.
● Loosen the tapping screw (R/L) securing the lower and
rear end of the floor panel.
● Pull the front part of the floor side cover to remove the
floor panel.
● Remove the floor side cover.
WASHER
WASHER
WASHER SCREW
SCREW
SCREW
FLOOR PANEL
● Remove the plug maintenance cover. ( 3-3 )
FLOOR PANEL CAP
● Loosen the tapping screw securing the battery cover to
remove the battery cover.
● Disconnect the battery wiring to remove the battery.
● Remove the floor side cover.
● Remove the floor panel cap A and B.
● Loosen the 4 washer bolts securing the floor panel.

● Remove the floor panel from the connecting groove of
the inner box by lifting the rear part of the panel
WASHER BOLT slightly.
● Draw the floor panel moving it to the right and left to
remove it.
3-4
EXTERNAL PARTS
SPECIAL
SPECIAL
SPECIAL BOLT
BOLT
BOLT
FRONT COVER
● Loosen the upper cover set screws (R/L) securing the
inner box.
SETTING
SETTING
SETTING
SCREW
SCREW
SCREW ● Loosen the upper cover set screws (R/L) securing the
front under cover.
● Loosen the special bolt securing the front of the front
cover.
● Draw the upper part of the front cover to remove it.
● Disconnect the head light wiring and remove the front
cover.
•Check for proper alignment of the connection (hook)

before performing installation.
SPECIAL
SPECIAL
SPECIAL SCREW
SCREW
SCREW
FRONT FENDER
● Loosen the flange bolts (R/L) securing the front fork.
● Remove the front fender.
INNER COVER
● Remove the floor side cover. ( 3-4)
● Remove the floor panel. ( 3-4)
● Remove the front cover. ( 3-5)
● Loosen the tapping screws (R/L) securing the front
SCREW
under cover.
SCREW
SCREW
● Loosen the special bolts securing the right and left
sides of the front cover.
● Turn the main key cover slightly to release the locking
TAPPING
and remove the cover.
TAPPING
TAPPING
SCREW
SCREW
SCREW
● Remove the cover set screw securing the back holder,
take off the joint part of the front under cover and
remove the inner box.
3-5
EXTERNAL PARTS
FRONT UNDER COVER

● Remove the inner box. ( 3-5)
● Remove the front fender. ( 3-5)
● Remove the front wheel. ( 10-5 )
CLIP
CLIP
CLIP ● Loosen the flange bolts securing the lower end of the
inner box.
● Remove the front under cover.
•Pay attention not to turn over the vehicle.

FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT
FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT
MUFFLER
● Loosen the 3 flange nuts securing the EX pipe comp.
● Loosen the 2 flange bolts securing the R. crankcase.
FLANGE BOLT
FLANGE
FLANGE BOLT
BOLT ● Loosen the 2 flange bolts securing the rear wheel mud
guard.
● Remove the EX muffler comp.
•Never perform the maintenance of the muffler right

after stopping the vehicle because the muffler is
extremely hot
FLANGE
FLANGE
FLANGE NUT
NUT
NUT
EX. PIPE REMOVAL
● Loosen the 2 flange bolts securing the cylinder comp.
● Remove the EX pipe by drawing it to the ground
FLANGE NUT direction.
INSTALLATION
● Install the 2 flange bolts after securing the EX pipe
with the stud bolt of the cylinder comp.
● Install the gasket on the EX muffler, connect the EX
pipe and install the 2 flange nuts temporarily.
● Install the 2 flange bolts on the R. crankcase
temporarily.
● Tighten the 3 flange nuts to install the EX muffler and
the EX pipe.
● Install the 2 flange bolts on the rear wheel mud guard.
● Tighten the muffler securing 2 flange bolts to install the
R. crankcase.
● Tightening torque of the R. crankcase.
TORQUE : 3.3kgf· ·m
•When installing the gasket, replace it with the new

one.
•Check to see if there is any evacuation after installing
the muffler.
3-6
EXTERNAL PARTS
WASHER
WASHER BOLT
WASHER BOLT
WASHER BOLT
BOLT
REAR FENDER
● Luggage box. ( 3-3)
● Plug maintenance cover. ( 3-3)
● Center cover. ( 3-3)
● Rear carrier. ( 3-3)
● Body cover. ( 3-3)
● Taillight base. ( 3-4)
● Remove the 2 washer bolts securing the fuel tank
support stay.
● Draw the rear part of the rear fender from the bracket in
the frame.
● Loosen the rear cushion under bolt, remove the rear fender.
•If removal is difficult, recheck each connection and

try removing again.
FLANGE BOLT REAR WHEEL MED GUARD

● Loosen the 2 flange bolts securing the EX muffler.
● Loosen the flange bolt securing the air cleaner.
● Loosen the flange bolt securing the inlet pipe.
● Remove the rear wheel mud guard.
REAR WHEEL MUD GUARD
•Never perform the maintenance of the muffler right

after stopping the vehicle because the muffler is
extremely hot.
UNDER COVER
● Remove the floor side cover. ( 3-4)
● Remove the engine hanger side cover. ( 3-5)
● Loosen the 2 R/L setting screws securing the frame.
● Remove the under cover.
UNDER COVER
SETTING SCREW
3-7
LUBRICATION SYSTEM
LUBRICATION POINTS
OIL THROTTLE SPEEDOMETER GREASE

BRAKE HOSE THROTTLE GRIP
GREASE
STEERING BEARING
WHEEL BEARING
WHEEL BEARING
GREASE SIDE STAND PIVOT
SPEEDOMETER GEAR BOX GREASE
GREASE
GREASE
4-0
4. LUBRICATION SYSTEM
SERVICE INFORMATION 4-1 OIL PUMP BLEEDING 4-4

TROUBLESHOOTING 4-1 ENGINE OIL LEVEL INSPECTION 4-6
OIL SYSTEM DRAWING 4-2 TRANSMISSION OIL INSPECTION 4-7
OIL PUMP DISASSEMBLY/ OIL TANK DISASSEMBLY 4-8
ASSEMBLY 4-3
LUBRICATION POINTS 4-9
OIL PUMP INSPECTION/
ADJUSTMENT 4-3
4
SERVICE INFORMATION
·Remove air from oil tube and oil pump if the oil tube is taken off or if air enters the oil tube.
● If the oil tube is disassembled, remove the air in the oil pass tube.
● Maintenanace on the oil pump is done without the engine being removed from the vehicle.
● When disassembling the oil pump, do not allow foreign substances from entering the engine or oil pump.
● Do not disassemble the oil pump assembly.
● If the oil tube is disassembled, place a tube clip or band on the oil tube to prevent oil from leaking out.
TROUBLESHOOTING
Overheating or engine clogging
● Faulty adjustment of oil pump(insufficient amount pumped).
● Bad quality of engine oil.
● Engine oil not being injected or blocked, bent strainer screen or oil tube.
● Entering of air in oil tube system.
● Faulty oil pump.
● Engine oil not being supplied from oil tank.
-Blocked oil tank cap air hole
-Blocked oil strainer screen
Excess exhaust smoke, accumulation of carbon on spark plug

● Faulty adjustment of oil pump(over-pumped amount).
● Bad quality of engine oil.
4-1
LUBRICATION SYSTEM
OIL SYSTEM DRAWING
4-2
LUBRICATION SYSTEM
OIL PUMP CONTROL CABLE OIL PUMP DISASSEMBLY/ASSEMBLY
● Remove
- Rear wheel mud guard. ( 3-8 )
INLET PIPE - Air cleaner. ( 5-4 )
- Carburetor. ( 5-4 )
FLANGE BOLT
● Loosen the oil pump cable stay bolt to remove the oil
pump anchor plate.
● Disconnect the oil control cable from the oil pump.
● Remove the inlet pipe. ( 5-9)
OIL ANCHOR PLATE

● Remove the oil tube in the oil pump side.
OIL PASS TUBE ● Remove the oil pass tube.
● Loosen the flange bolt securing the oil pump.
OIL TUBE ● Remove the setting plate of the oil pump.
● Remove the oil pump.
•When assembling/disassembling the oil pump, do

not allow foreign substances from entering the
engine and oil tube by cleaning around the oil pump.
SETTING PLATE •If the air enters into the oil line, it may cause faulty
lubrication or engine sticking. Always remove the air
in the oil line after maintenance.
• Pay attention not to damage the O-ring when
assembling the oil pump.
OIL PUMP
OIL PUMP INSPECTION/ADJUSTMENT

● Remove the oil pump.
● Rotate the shaft and check for proper rotation.
● Check the gear for wear, damage and leak of each seal.
● If the oil comes out from the outlet of the oil pump
after connecting the oil tube (which is connecting
between the tank and the oil pump) to the inlet and
rotating the shaft in the driving direction, consider the
oil pump is in good condition.
4-3
LUBRICATION SYSTEM
ADJUSTMENT
CONTROL •Perform after inspection and adjustment of throttle

LEVER cable.
● Check to see if the matching mark of the oil pump

body and control lever are aligned in a state where
the throttle grip is completely rotated.
● Adjustment is performed by loosening the oil pump
control cable lock nut and turning the control nut.
● While the engine is running, slightly open the throttle
and check to see if the control lever operates together
CABLE
CABLE
CABLE STAY
STAY
STAY NUT
NUT
NUT with the increase in engine rpms.
•Do not adjust the control lever matching mark to the

closed side of the oil pump body matching mark. If
this is done, the amount of pumped oil is reduced,
negatively affecting the engine.
•Make sure that the open axis stays within an 1mm
sphere.
● The following occurs when the oil pump is adjusted

incorrectly.
-When the oil pump lever is excessively opened :
Emitting of white exhaust gas or starting problems.
OIL PUMP CABLE
-When the oil pump lever is insufficiently opened :
STAY NUT
Clogging of engine.
•If the oil pump cable stay bolt is removed, apply the
screw locking compound to the bolt thread.
OIL PUMP BLEEDING
CONTROL
LEVER •Air infiltration in the oil pass may cause the engine
sticking. Always remove the air in the oil pass after
maintenance.
•When disassembling the oil tube, air can be enter
into the oil tube and the oil pump because of the oil
leaking in the oil tube. Remove the air completely.
•Do not allow foreign substances from entering the oil
pass.
4-4
LUBRICATION SYSTEM
OIL PUMP/OIL TUBE INSPECTION
● Fill the oil tank with engine oil.
● Cap around the oil pump and the carburetor with dry
cloth.
● Locate the end of the oil tube in the level lower than the
OIL
OIL TUBE
OIL TUBE
TUBE oil tank and drain the oil to bleed the air.
● Install the oil tube in the oil pump.
●Incline the oil pump to locate the oil pump shaft at the
angle of 45。from the “▲ ”mark with oil tube
connected.
●In this state, locate the oil pump in the level lower
than the oil tank and drain the oil to bleed the air.
●Install the oil pump shaft in the oil pump after
completing the bleeding.
●Install the oil pump in the crankcase.
OIL PASS TUBE INSPECTION

● Bend the oil pass tube in the “U” shape, keep the two
ends parallel with each other and fill the oil pass tube
with the oil.
4-5
LUBRICATION SYSTEM
● Connect the oil pump and then the carburetor quickly
with the both ends of the tube pressed to avoid the air
from entering.
•Make sure that the tubes are arranged correctly.
● Start the engine.
•Do not start the engine in the poorly-ventilated area.
● Open the oil pump control level fully and idle for
2minutes to bleed the air remained in the oil pass tube
with the oil drained from the oil pump.
•Do not increase the engine RPM more than required.

CONTROL LEVER
● Connect the oil control cable.
•Adjust the oil pump if the adjustment nut of the oil

comtrol lever is loose.
OIL PASS TUBE
ENGINE OIL LEVEL INSPECTION

● Check the engine oil level if the pilot lamp blinks when
the main switch is turned on.
LOW OIL WARNING LIGHT BLINKING LEVEL : 0.3
OIL
OIL
OIL WARNING
WARNING
WARNING LIGHT
LIGHT
LIGHT
4-6
LUBRICATION SYSTEM
● Remove the oil tank cap and fill the oil tank with oil to
the level of the projected portion
RECOMMENDED OIL : ULTRA 2 SUPER OIL
● Reinstall the oil tank cap and check to see if the pilot
lamp turns off when the main swich is turned on.
TRANSMISSION OIL INSPECTION

● Check the body and the connection of each engine
component for any leak.
OIL CHECK ● Remove the oil check bolt and check to see if the oil
BOLT overflows from the oil check hole.
● If only the small amount of oil overflows, fill the
recommended transmission oil through the oil filler
hole gradually.
•Oil level inspection must be performed in the flat

ground with the vehicle being straight by raising the
main stand.
RECOMMENDED OIL : SAE 80W / 90
● Tighten the oil level check bolt.
TIGHTENING TORQUE : 1.3kgf·m
● Start the engine and check for leak.
4-7
LUBRICATION SYSTEM
OIL TANK DISASSEMBLY

● Remove the luggage box.
FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT ● Remove the oil level switch connector.
● Remove the tube in the oil pump.
● Install the tube clip or the valve in the oil tube to avoid
the oil from leaking.
● Remove the flange bolt securing the oil tank and press
the left and lower rear fender to remove the oil tank.
● Drain the oil from the oil tank.
● Remove the oil level switch.
● Remove the oil tube.
● Remove the oil strainer.
OIL
OIL
OIL LEVEL
LEVEL
LEVEL SWITCH
SWITCH
SWITCH CONNECTOR
CONNECTOR
CONNECTOR
INSPECTION
● Check the oil level switch and the oil tube for proper
installation.
•If the oil enters into the oil pass, it may cause
abnormal lubrication or engine sticking. Always
remove the air in the oil pass after maintenance.
OIL LEVEL SWITCH •Make sure that the oil tube is connected properly.
•Drain the oil in the clean container.
•Install the oil strainer after cleaning it.
4-8
MEMO
FUEL SYSTEM
FUEL GAUGE
FUEL TANK
FUEL AUTO COCK
STRAINER
CARBURETOR
5-0
5. FUEL SYSTEM
SERVICE INFORMATION 5-1 CARBURETOR REMOVAL/

TROUBLESHOOTING 5-2 INSTALLATION 5-4
FUEL TANK 5-3 CARBURETOR INSPECTION 5-6
AIR CLEANER REMOVAL 5-4 THROTTLE VALVE 5-7
AIR CLEANER ELEMENT FUEL AUTO COCK 5-8
DISASSEMBLY 5-4 INLET PIPE REED VALVE 5-9
SERVICE INFORMATION
GENERAL SAFETY
•Gasoline is extremely flammable. Avoid fire in the work place, also paying particular attention to sparks.
Furthermore, the evaporated (gasified) gasoline is highly explosive. Work in a well-ventilated areas.
•Exhaust gas contains poisonous substance. Do not keep engine running for a long period of time in a closed, or poorly
ventilated area.
•Do not excessively bend or twist cable. Distorted or damaged cable may lead to mechanical malfunctions.
•Pay particular attention to the position of O-ring. Replace with new ones when disassembled.
•If it is desired to store a vehicle for a period longer than 1 month, drain gasoline out of the carburetor float chamber.
Gasoline left in the float chamber will be deteriorated causing the slow jet to be clogged with deposits, and idling may
become unstable.
SPECIFICATIONS
FUEL TANK CAPACITY : 5.8ℓ
RESERVE FUEL CAPACITY: 1.7ℓ
CARBURETOR
ITEM STANDARD ITEM STANDARD
TYPE/THROTTLE BORE PB11P PILOT SCREW OPENING 1, 1/4 RETURNS
VENTURI DIAMETER 16mm OR EQUIVALENT FLOAT LEVEL 8.0mm
MAIN JET No. #65 IDLING SPEED 1,800±100rpm
SLOW JET No. #38 THROTTLE GRIP FREE PLAY 2-6mm
TOOL
FLOAT LEVEL GAUGE
5-1
FUEL SYSTEM
TROUBLESHOOTING
The vehicle does not start. Back firing
● No gasoline in fuel tank. ● Ignition system is damaged.

● Fuel is not coming out of carburetor. ● Mixture is too lean.
● Too much fuel is flowing into cylinder.
● No spark emitted from spark plug.
● Air cleaner is blocked.
● Suction system is experiencing secondary intake of air. Insufficient power and high fuel consumption.
● Using low quality gasoline.
● Starter is damaged. ● Air cleaner is blocked.
● Throttle cable is working improperly. ● Ignition system is damaged.
● Fuel tank is functioning improperly. ● Mixture is too rich.
Idle is unstable and engine turns off after starting. Air/Fuel mixture is extremely lean
● Starter is damaged. ● Fuel jet is blocked.

● Ignition system is damaged. ● Float valve is damaged.
● Using low qualty gasoline. ● Oil level is low.
● Suction system is experiencing secondary intake of air. ● Bad ventilation of air in tank cap.
● Idle is adjusted improperly. ● Fuel strainer screen is blocked.
● Air screw is adjusted improperly. ● Fuel tube is bent, creased or blocked.
● Compression pressure is low. ● Suction system is receiving secondary suction of air.
● Air/Fuel mixture is either too lean or rich.
● Carburetor is blocked.
Air/Fuel mixture is extremely rich.
Mis-firing occurs when driving at high speeds. ● Air jet is blocked.

● Float valve is damaged.
● Ignition system is damaged. ● Oil level is too high.
● Mixture is too lean. ● Starter is damaged.
● Air cleaner is blocked.
5-2
FUEL SYSTEM
FLANGE
FLANGE BOLT
FLANGE BOLT
FLANGE BOLT
BOLT
FUEL TANK
REMOVAL
•Gasoline is extremely flammable. Avoid fire during

work, and pay particular attention to electric sparks.
Furthermore, the evaporated (gasified) gasoline is
highly explosive. Work in a well-ventilated areas.
● Remove the following parts.

- Plug maintenance cover.( 3-3 )
- Rear carrier. ( 3-3)
- Body cover. ( 3-3)
- Taillight base. ( 3-4)
- Fuel tube from the fuel auto cock.
•Use the tube clip or the cap to prevent the gasoline

from leaking.
AUTO
AUTO
AUTO COCK
COCK
COCK
SEAT CATCH ● Remove the fuel unit wire coupler.

FUEL UNIT
FLANGE ● Remove the rear fender. ( 3-7)
BOLT ● Loosen the 2 flange bolts and remove the seat catch.
● Loosen the 2 flange bolts and remove the fuel tank
support stay.
● Loosen the 2 flange bolts and remove the fuel tank.
INSTALLATION
Install in the reverse order of removal.
• Check for gasoline leakage.

•“Gasoline”mark is on the fuel tank cap.
• Check this mark when filling gasoline.
5-3
FUEL SYSTEM
FLANGE BOLT AIR CLEANER REMOVAL
WASHER ● Loosen the air cleaner connecting bend screw pin.
SCREW ● Loosen the 2 bottom air cleaner washer bolts.
● Loosen the top rear fender flange bolt.
● Remove the air cleaner from the carburetor.
WASHER BOLT
AIR CLEANER ELEMENT AIR CLEANER ELEMENT DISASSEMBLY

● Loosen the 5 air cleaner cover washer screws.
CONNECTING
● Remove the air cleaner cover.
BEND
● Remove the air cleaner element.
● Install in the reverse order of disassembly.
CARBURETOR REMOVAL/INSTALLATION
•Fire is strictly prohibited.

•Open the drain screw to drain the gasoline in the
carburetor chamber.
● Remove
- Plug maintenance cover. ( 3-3)
- Air cleaner. ( 5-4)
CARBURETOR
CARBURETOR INSULATOR
CARBURETOR INSULATOR
INSULATOR CARBURETOR
CARBURETOR
CARBURETOR - Wiring coupler of the auto by starter.
- Oil pass tube.
- Throttle valve set.
- 2 flange bolts securing the inlet pipe.
- Carburetor insulator.
- Carburetor.
•Install the carburetor after aligning the throttle valve

cutaway and the throttle stop screw.
•Tighten the top set correctly so that it is not released.
FLANGE BOLT CARBURETOR

INSULATOR
5-4
FUEL SYSTEM
CARBURETOR DISASSEMBLY/ASSEMBLY
● Remove the auto by starter cover.
● Loosen the 2 washer screws
● Remove the auto by starter set plate.
AUTO BY WASHER SCREW ● Remove the auto by starter.
STARTER COVER AUTO BY STARTER ● Remove the auto by starter O-ring.
SET PLATE ● Assemble in the reverse order of disassembly.
AIR SCREW
•Install the auto by starter in the carburetor body after

applying grease to the starter O-ring and then tighten
THROTTLE firmly with set plate piece.
AUTO BY STOP
STARTER SCREW
GASKET
FLOAT
FLOAT PIN
VALVE
FLOAT
O-RING
FLOAT
CHAMBER
FLOAT CHAMBER/FLOAT/JET
DISASSEMBLY/ASSEMBLY
● Loosen the 2 float chamber screws.
FLOAT LEVEL
GAUGE CHECK
● Float valves and seats for cracks or damage.
● Float valve operation.
● Float valve level.
FLOAT LEVEL : 8mm
REMOVE
● Main jet, needle jet holder, and needle jet, and remove
THROTTLE the slow jet.
STOP SCREW ● Air screw, spring, washer, O-ring.
WASHER AIR SCREW ● Throttle stop screw, spring, O-ring.
O-RING
SLOW JET
MAIN JET
FLOAT
FLOAT VALVE
5-5
FUEL SYSTEM
CARBURETOR PASSAGES CLEANING
● Disassemble all component parts of carburetor and
then clean the air and fuel passages of carburetor body
with compressed air.
•Do not use it wire, otherwise the carburetor body and

fuel pump get damaged.
● Assemble in the reverse order of disassembly.
AIR GUN
•Be sure to install the needle jet with the smaller hole
toward the float chamber.
•Install the air screw and its O-ring and washer in the
order as shown in the drawing. If the air screw and
carburetor body are replaced with the new ones,
adjustment is necessary.
•Do not fasten it strongly, otherwise the face of seat
get damaged.
CARBURETOR INSPECTION
● Connect an ohmmeter to the auto bystarter wire
connector terminals and measure the resistance. If the
resistance is greatly out of specification, it indicates a
faulty PTC in the auto bystarter. Replace the auto
bystarter.
RESISTANCE:4.0Ω±1Ω(20 C)
•The auto by starter might be normal if the resistance

is only slightly out of specification. However, be sure
to check all related parts for trouble.
● Remove the carburetor and let it cool down for 30

minutes. Insert a vinyl tube into the fuel increasing
circuit and blow into the tube.
● Air should flow into the circuit.
● If air does not flow into the circuit, replace the auto
bystarter.
5-6
FUEL SYSTEM
● Connect the battery to the auto bystarter terminals and
wait for 5 minutes.
● Insert a vinyl tube into the fuel increasing circuit and
blow into the tube.
● Air should not flow into the circuit. If air flows into the
circuit, replace the auto bystarter.
● Check the resister if the auto bystarter is normal but

engine is still hard to start.
● If there is a broken wire in the resister, current will not
flow to the PTC and the auto bystarter will not operate.
● If there is a shorted wire in the resister, current of a
higher voltage than specified will reach the PTC. This
will cause the fuel enrichening circuit to close too soon,
and starting will be difficult.
THROTTLE VALVE
REMOVE
● Throttle valve.
● Throttle cable.
● Throttle valve spring.
● Needle clip.
● Seal cap.
● Clip.
● Jet needle.
ASSEMBLY
● Install the jet needle into the throttle valve and be sure
to fixes the needle clip.
● Route the throttle cable through the spring and
compress the spring fully.
● Attach the throttle cable end to the bottom of the
throttle valve and thread the throttle cable through the
slot in the valve.
● Align the cutout in the throttle valve with the throttle
stop screw on the carburetor body and install the valve
on the carburetor.
•Be sure to check if the cutaway turns toward air

cleaner. If it is assembled reversely, the engine may
spring up like fountain due to the throttle valve not
going down.
● Operate the valve after installing the throttle valve.
5-7
FUEL SYSTEM
FUEL AUTO COCK

REMOVAL/INSTALLATION
● Remove
- Luggage box. (⇨3-3)
- Plug maintenance cover. (⇨3-3)
- Center cover. (⇨3-3)
- Rear carrier. (⇨3-3)
- Body cover. (⇨3-3)
- Fuel tube A, B connected to the carburetor.
- Inlet pipe negative pressure tube.
- Fuel tube A, B connected to the fuel tank.
FUEL
FUEL
FUEL AUTO
AUTO
AUTO COCK
COCK
COCK - Flange bolt securing the fuel auto cock and the frame.
- Fuel auto cock.
INSPECTION
•Gasoline is extremely flammable and is explosive

under certain conditions.
● Keep flames and sparks away from gasoline and wipe

up spilled gasoline at once.
•Be sure to remove the diaphragms from the fuel auto

valve before using compressed air to blow out the air
passages. Compressed air wil damage the
diaphragms or may force them off the aluminum
link.
● Disconnect the fuel line and place it in a clean

container as shown.
•Place a clean container under the fuel tube.
● Connect the fuel auto valve vacuum tube to the

vacuum pump and apply vacuum. Be sure that the fuel
flows out smoothly. If the vacuum does not remain
steady, it indicates the diaphragm is incorrectly
installed or damaged. If the vacuum remains steady, but
the fuel flow is not smooth, it indicates a clogged filter
or incorrectly installed diaphragm.
● If the fuel flows without the vacuum applied, the
diaphragm is incorrectly installed.
5-8
FUEL SYSTEM
INLET PIPE•REED VALVE

● Remove
FLANGE
- Luggage box. (⇨3-3)
FLANGE - Air cleaner. (⇨5-4)
BOLT BOLT
- Carburetor. (⇨5-4)
- Negative pressure tube connected to the inlet pipe.
- Oil pump cable. (⇨4-3)
- Rear wheel mud guard. (⇨3-8)
- Inlet pipe securing 4 flange bolts connected to the L
crank case.
- Oil pump anchor plate.
REAR WHEEL MUD GUARD - Inlet pipe.
- Reed valve.
•Do not remove the reed valve and replace the

assembly if necessary.
REED •Keep the foreign material from entering into the
VALVE engine by cleaning around the needle valve.
INSPECTION
● Check the reed valve for fatigue or damage and replace
the reed valve assembly if necessary.
● Check the reed valve seat for cracks, damage and
clearance from the reed and replace the reed valve
assembly if necessary.
•Be sure to replace the reed valve as an assembly.

Disassembling or bending the reed stopper will cause
engine trouble.
5-9
ENGINE REMOVAL/INSTALLATION
6-0
6. ENGINE REMOVAL/INSTALLATION
SERVICE INFORMATION 6-1
ENGINE REMOVAL/INSTALLATION 6-2
ENGINE HANGER LINK REMOVAL 6-3
SERVICE INFORMATION
GENERAL SAFETY
•Use a jack to remove or install the engine. Support the motorcycle with a jack firmly, taking precautions not to
damage the frame, engine, cable or harness.
•Attach tape to the frame to protect it during the engine removal or installation. 6
● The following works can be carried out without removing the engine from the vehicle body.
-TRANSMISSION (⇨SECTION 9)
-A.C. GENERATOR (⇨SECTION 13)
-KICK STARTER/ CONTINUOUSLY VARIABLE TRANSMISSION (⇨SECTION 7)
-CYLINDER HEAD/ CYLINDER/ PISTON (⇨SECTION 8)
-CARBURETOR (⇨SECTION 5)
-OIL PUMP (⇨SECTION 4)
● Items to be worked after removing engine

-CRANKSHAFT, CRANKSHAFT BEARING, CRANK CASE BEARING.
TORQUE VALUES :
ENGINE HANGER BOLT (ENGINE) : 5.0㎏f·m
(FRAME) : 7.3㎏f·m
6-1
OIL TUBE CAP TOP

● Remove
- Luggage box. (⇨3-3 )
- Plug maintenance cover. (⇨3-3 )
- Center cover. (⇨3-3 )
● Disconnect
- AC generater coupler. (⇨13-7 )
- Carburetor auto bystarter coupler.
● Remove
- Spark plug cap.
- Oil pump cable.
- Oil tube connected to the oil pump.
NEGATIVE PRESSURE TUBE - Negative pressure tube connected to the inlet pipe.
- Fuel tube connected to the carburetor.
● Loosen the carburetor cap top, remove the throttle valve.
● Loosen the rear brake adjust nut, remove the brake arm
joint B and rear brake cable.
● Remove the bottom rear cushion under bolt.
ADJUSTER NUT
● Loosen the engine hanger U-nut.

● Loosen the engine hanger flange bolt.
● Remove the engine. (with the muffler and rear wheel
attached)
REAR
CUSHION
•Take action to prevent oil from leaking (Install the

clip in the oil tube)
•Take precautions not to damage the engine when
removing the engine from the chasis.
REMOVE
● Muffler. (⇨3-7 )
● Rear wheel. (⇨11-3 )
ENGINE
ENGINE
ENGINE
HANGER
HANGER
HANGER U
HANGER U NUT
U NUT
NUT •Pay attention not to damage wiring and cable and not
BODY
BODY COVER
BODY COVER
BODY CLIP
COVER CLIP
COVER CLIP
CLIP to damage the threded part of bolts.
•Arrange the cable tubes and wiring in the right
positions.
6-2
● Check the following after the engine is assembled.
-Electric systems.
-Adjust of the rear brake free play.
-Inspection of the throttle cable operation.
-Inspection of the oil pump cable operation.
6-3
KICK STARTER/CONTINUOUSLY VARIABLE TRANSMISSION
GUIDE PIN SHOE SPRING

CLUTCH SHOE
MOVABLE DRIVEN CLUTCH OUTER
MOVABLE DRIVEN FACE DRIVE PLATE
FACE SPRING
DRIVEN FACE DRIVE BELT
DRIVE FACE
KICK DRIVEN GEAR
RAMP PLATE DRIVE FACE BOSS

WEIGHT ROLLER
MOVABLE DRIVE FACE
KICK STARTER SPINDLE
KICK STARTER RETURN SPRING
KICK SPINDLE BUSH
7-0
7. KICK STARTER/CONTINUOUSLY
VARIABLE TRANSMISSION
SERVICE INFORMATION 7-1 DRIVE BELT 7-4
TROUBLESHOOTING 7-1 DRIVE PULLEY 7-6
L. SIDE COVER REMOVAL 7-2 CLUTCH/DRIVEN PULLEY 7-8
KICK STARTER 7-2
SERVICE INFORMATION
GENERAL SAFETY
● Do not allow oil to contact the drive belt or the pulley face. The transmission rate of driving force is reduced with oil
contact.
● Do not operate starter motor while the L. crank case front cover is removed.
7
·Pay attention not to apply the grease oil to the movable drive face or weight roller.
SPECIFICATIONS
ITEM STANDARD SERVICE LIMIT
MOVABLE DRIVE FACE BUSHING INNER DIAMETER 20.035-20.085mm 20.60mm
DRIVE FACE BOSS OUTER DIAMETER 20.011-20.025mm 19.97mm
DRIVE BELT WIDTH 17.5mm 16.50mm
WEIGHT ROLLER OUTER DIAMETER 15.920-16.080mm 15.40mm
CLUTCH OUTER AND INNER DIAMETER 107.0-107.2mm 107.50mm
DRIVEN FACE SPRING PLAY 98.1mm 92.8mm
DRIVEN FACE OUTER DIAMETER 33.965-33.985mm 33.94mm
DRIVEN FACE INNER DIAMETER 34.000-34.025mm 34.06mm
TROUBLESHOOTING
Engine starts but motorcycle does not work. Vehicle unable to run at the maximum speed,
● Drive belt worn. or lack of output
● Ramp plate damaged. ● Drive belt worn.
● Clutch shoe worn or damaged. ● Defective movable driven face spring.
● Movable driven face spring cut. ● Weight roller worn.
● Pulley face contaminated.
Engine stops, or the vehicle runs suddenly,
after starting.
● Clutch shoe spring cut.
7-1
L. SIDE COVER REMOVAL

● Remove
- 13 flange bolts securing L. side cover.
- Rear brake cable clamp.
- L. side cover gasket.
- Dowel pin.
L. SIDE COVER
FLANGE BOLT
·Install the new gasket and dowel pin after removing

the gasket of the crankcase surface.
·Align the bolts to uniform the tightening location
before tightening then when you don’t know the bolt
length.
·Tighten the bolts diagonally with specified tightening
torque.
TORQUE : 1.0kgf·m
KICK STARTER ARM
KICK STARTER
● Remove
- L. side cover. ( 7-2 )
- Kick starter ratchet and the thrust washer while rotating
the kick starter arm.
● Loosen the flange bolt securing the kick starter arm,
remve the kick starter arm.
● Remove
- 14mm external circlip.
- Kick spindle washer.
- Kick starter spindle.
KICK DRIVEN GEAR - Kick spindle spring, bush.
INSPECTION
● Wear and damage of the kick starter spindle and gear
portion.
● Damage to return spring.
● Defects and damage of the kick starter spindle bushing.
● Wear and damage of the kick starter ratchet.
● Damage to friction spring.
KICK SPINDLE
BUSH
RETURN SPRING
7-2
KICK STARTER INSTALLATION
INSTALL
● Kick spindle bush, spring in the L. side cover.
● Kick starter spindle in the L. side cover.
● Kick starter spindle washer.
● 14mm external circlip in the L. side cover.
● Kick starter arm.
● Kick spindle springn in the groove of the L. side cover.
● Thrust washer.
KICK SPINDLE BUSH THRUST WASHER
● Rotate the kick starter spindle using the kick starter

arm, draw the spindle to the L. side cover and assemble
the kick starter ratchet.
KICK DRIVEN GEAR

·When installing the 14mm external circlip, keep

holding the spindle manually and install the circlip in
the groove correctly.
·Apply the grease to the kick starter ratchet groove
and gear.
·Check the kick starter ratchet and the kick starter
spindle for smooth operation after installation.
KICK DRIVEN GEAR
7-3
DRIVE BELT
REMOVAL
● Remove the L. side cover. ( 7-2 )
● Hold the clutch outer using the universal holder and
remove the nut.
● Remove the clutch outer.
TOOL: UNIVERSAL HOLDER
·Use the special tool when loosening the lock nut.

L. SIDE COVER Holding the rear wheel or rear brake will damage the
final reduction system.
● Squeeze the drive belt into the pulley groove as shown

so that it slackens enough to remove the driven pulley
from the drive shaft.
● Loosen the drive face setting nut 12mm with the clutch
center holder.
TOOL: CLUTCH CENTER HOLDER
REMOVE
● Driven pulley/ clutch with the drive belt in place.
● Drive belt from the driven pulley groove and drive
pulley groove.
DRIVE FACE
DRIVEN PULLEY
DRIVE BELT
7-4
DRIVE BELT INSPECTION
● Check the drive belt for cracks, pry separation and
wear; replace as necessary.
● Measure the width of the drive belt as shown.
● Replace the belt if the service limit is exceeded.
·Use only a genuine DAELIM replacement drive belt.

·Do not get oil or grease on the drive belt or pulley
faces. Clean off any grease or oil before reinstalling.
DRIVE BELT INSTALLATION

● Temporarily install the driven pulley/clutch assembly
on the drive shaft.
● Turn the pulley clockwise and spread the faces apart
while installing the drive belt.
● Remove the pulley assembly once with the drive belt
installed.
·Hold the pulley faces apart preventing them from

closing.
● Put the drive belt over the drive pulley.

● Reinstall the driven pulley on the drive shaft with the
drive belt attached.
● Install the clutch outer and the universal holder. Tighten

the nut to the specified torque.
TORQUE VALUE : 4.0kgf·m

TOOL : UNIVERSAL HOLDER
● Reinstall the L. side cover.
7-5
DRIVE PULLEY
REMOVAL
● Remove the L. side cover. ( 7-2 ) @?hfV/X?e
@?hf?V/Xe
@?
@?
@?hf?W.Ye
)Xh
@)X?g
@V/Xg
@?V/X?f
@@@@@@@@@@@??V/Xf
N1e
J5e
@@@@@@@@@@@?eW.Y?e
@??W.Yf
@?W.Y?f
@W.Yg
@(Y?g
(Yh
● Hold the drive face using the clutch center holder and
remove the nut and washer.
TOOL : CLUTCH CENTER HOLDER
● Remove the drive face.
L. SIDE COVER
● If the drive pulley holder cannot be used, remove the

cooling fan at the right side of the crankshaft, and hold
the flywheel with the universal holder.
MOVABLE DRIVE FACE DISASSEMBLY

● Remove
- Dirve face. ( 7-6 )
)Xh
@)X?g
@V/Xg
@?V/X?f
@@@@@@@@@@@??V/Xf
@?hfV/X?e
@?hf?V/Xe
@? N1e
@?
@?hf?W.Ye J5e
@@@@@@@@@@@?eW.Y?e
@??W.Yf
@?W.Y?f
@W.Yg
@(Y?g
(Yh
- Drive belt. ( 7-4 )

)Xh
@)X?g
@V/Xg
@?V/X?f
@@@@@@@@@@@??V/Xf
@?hfV/X?e
@?hf?V/Xe
@?
@? N1e
J5e
@?hf?W.Ye
@@@@@@@@@@@?eW.Y?e
@??W.Yf
@?W.Y?f
@W.Yg
@(Y?g
(Yh
- Movable drive face.
● Remove the ramp plate and weight rollers from the

WEIGHT ROLLER movable drive face.
RAMP PLATE
DRIVE MOVABLE
FACE BOSS DRIVE FACE
7-6
MOVABLE DRIVE FACE INSPECTION
● The weight rollers push on the movable drive pulley
face (by centrifugal force); worn or damaged weight
rollers will interfere with this force.
● Check the rollers for wear or damage and replace as
necessary.
● Measure the O.D. of each roller, replace if the service
limit is exceeded.
● Check the drive face boss for wear or damage and

replace as necessary.
● Measure the O.D of the drive face boss. Replace the
boss if the service limit is exceeded.
● Measure the I.D. of the drive face. Replace it if the
service limit is exceeded.
● Movable drive face boss outer diameter
● Movable drive face inner diameter
MOVABLE DRIVE FACE ASSEMBLY/INSTALLATION

● Install the weight roller on the movable drive face.
● Install the ramp plate.
● Pack the inside of the movable drive face with the
specified amount of grease.
● Install the movable drive face boss.
MOVABLE DRIVE FACE
·Do not get the grease on the pulley face. Remove any
misplaced grease with a degreasing agent.
● Install the movable face assembly on the crankshaft.
7-7
DRIVE FACE INSTALLATION
● Squeeze the drive belt into the pulley groove and pull
the drive belt over the drive face shaft.
● Hold the drive pulley face using the clutch center

holder and tighten the nut to the specified torque.

TOOL : CLUTCH CENTER HOLDER
● Install the drive pulley face, washer and nut.
·Tighten the drive pulley nut to the specified torque.

·Correctly match the drive pulley face and crank shaft
serration when assembling.
·If the universal holder cannot be used, remove the
cooling fan and hold the flywheel with the universal
holder.
● Install the L. side cover.
CLUTCH/DRIVEN PULLEY
DISASSEMBLY
● Remove
- L.side cover. ( 7-2 )
)Xh
@)X?g
@V/Xg
@?V/X?f
@@@@@@@@@@@??V/Xf
@?hfV/X?e
@?hf?V/Xe
@?
@? N1e
J5e
@?hf?W.Ye
@@@@@@@@@@@?eW.Y?e
@??W.Yf
@?W.Y?f
@W.Yg
@(Y?g
(Yh
- Drive face. ( 7-9 )

)Xh
@)X?g
@V/Xg
@?V/X?f
@@@@@@@@@@@??V/Xf
@?hfV/X?e
@?hf?V/Xe
@?
@? N1e
J5e
@?hf?W.Ye
@@@@@@@@@@@?eW.Y?e
@??W.Yf
@?W.Y?f
@W.Yg
@(Y?g
(Yh
● Hold the clutch outer using the universal holder and

remove the flange nut, then remove the clutch outer.
● Remove
- Drive belt.
- Driven pulley.
DRIVEN PULLEY ● Install in the reverse order of removal.
7-8
28mm SPECIAL NUT DISASSEMBLY
● The clutch/driven face are assembled toward the clutch

spring compressor.
·Make sure that the boss portions of the clutch/driven

face are matched with the clutch spring compressor
hole.
TOOL : CLUTCH SPRING COMPRESSOR
● Fix the clutch spring compressor with a vice, etc.

● Disassemble the 28mm special nut with a socket
wrench. Disassemble the clutch driven face form the
clutch spring compressor.

SOCKET WRENCH 39×41mm
● Assembly is done in the reverse order of disassembly.
REMOVE
● Seal collar from the driven pulley.
● Guide pins and guide pin rollers and the movable
driven pulley face.
·Some guide pin can be separated to the roller and the

pin.
● Remove the O-ring and oil seals from the movable

driven face.
INSPECTION
Clutch outer
● Measure the I.D. at shoe contact surface of the clutch

outer. Replace the outer if the service limit is exceeded.
7-9
Clutch Shoe Inspection
● Measure the thickness of each shoe ; replace if the

service limit is exceeded.
Movable Driven Face Spring Inspection
● Measure the free length of the driven pulley spring and

replace if the service limit is exceeded.
Driven Face Inspection

● Check the following;
-Both faces for damage or excessive wear.
-Guide pin groove for damage or deformation.
● Replace damaged or worn parts an necessary.
● Measure the O.D. of the driven face and the I.D. of the
movable driven face. Replace either part if the service
limit is exceeded.
Driven face outer diameter service limit : 33.94mm

Movable driven face inner diameter service limit : 34.06mm
Driven Face Bearing Inspection
● Check the inner bearing oil seal (if installed) for

damage; replace as necessary.
● Check the needle bearing for damage or excessive play
and replace as necessary.
● Turn the inner race of the outer bearing with your
finger. Check that the bearing turns smoothly and
quietly, and that the bearing outer race fits securely.
Replace the bearing if necessary.
7-10
CLUTCH SHOE REPLACEMENT
● Remove the E-clip and washers, then remove the
clutch shoes and shoe springs from the drive plate.
·Some models use one retainer plate instead of three

washers.
● Check the shoe springs for damage or loss of tension.
● Check the damper rubbers for damage or deformation;

replace as necessary.
● Apply a small amount of grease on the pivot pins.
● Install new clutch shoes on the pivot pins and push

them into place.
● Use a small amount of grease on the pivot pin and keep
grease off of the brake shoes. Replace the brake shoes
if there is any grease on them.
·Grease or oil damages clutch shoes and can lead to a

loss of engaging ability.
● Use pliers to hook the springs to the shoes.
7-11
● Install the E-clip and washers or retainer plate into the
pivot pins.
·Apply only to the belt type gearless transmission.

·Wipe the grease came out from the pivot pin
thoroughly.
DRIVEN FACE BEARING REPLACEMENT

● Remove the inner bearing
·If the driven face has an oil seal at inner bearing side,
remove the oil seal first.
·If a ball bearing is used oh the inside, remove the
snap ring first then remove the bearing.
● Remove the snap ring then drive out the outer bearing
toward the inner bearing side.
● Drive a new outer bearing into place with the sealed

end toward the outside. Install the snap ring securely.
·Apply the specified amount of specified grease as

shown.
GREASE APPLICATION : 5.0~5.5g
● Install in a new inner bearing
·Install the bearing with the sealed side facing out.

·Install the needle bearing using a hydraulic press.
Install the ball bearing by driving it in or using a
hydraulic press.
● Install the snap ring into the groove in the driven face.
● Install a new oil seal with the lip toward the bearing (if
required).
7-12
CLUTCH/DRIVEN PULLEY ASSEMBLY
● Install new oil seals and O-rings on the movable driven
pulley face.
●Lubricate the inside of the movable face with the

specified amount of grease.
GREASE APPLICATION : 5.0~5.5g
● Install the movable face on the driven pulley face.

● Install the guide pins, or guide pins and guide pin
rollers.
● Install the seal collar.
● Assemble the driven pulley, spring and clutch in the

clutch spring compressor. Compress the assembly by
turning the tool handle until the lock nut can be
installed.
● Clamp the clutch spring compressor in a vise and
tighten the lock nut to the specified torque using the
lock nut wrench.
● Remove the spring compressor.

● Install the clutch/driven pulley and drive belt onto the
dirve shaft.

SOKET WRENCH 39mm
7-13
CYLINDER HEAD/CYLINDER/PISTON
CYLINDER HEAD BOLT
CYLINDER HEAD
CYLINDER HEAD GASKET
CYLINDER
TOP RING
SECOND RING
EXPANDER
CYLINDER GASKET
STOPPER PIN
PISTON CLIP
PISTON PIN
NEEDLE BEARING
8-0
8. CYLINDER HEAD/CYLINDER/PISTON
SERVICES INFORMATION 8-1

TROUBLESHOOTING 8-1
FAN COVER, SHROUD REMOVAL 8-2
CYLINDER HEAD/ CYLINDER/ PISTON 8-3
SERVICE INFORMATION
GENERAL SAFETY
● Take precautions not to damage the joint part with a driver when removing the cylinder, or not to damage the cooling
pin by striking the cylinder too hard.
● Take precautions not to damage the inside of the cylinder or the exterior part of the piston.
● Check parts after disassembling, and clean and dry with an air hose prior to taking measurements.
SPECIFICATIONS
Unit : mm(in)
ITEM STANDARD VALUE SERVICE LIMIT
Inner diameter 39.000-39.005mm 39.05mm 8
CYLINDER Cylindricality - 0.10mm
Out of roundness - 0.10mm
PISTON, Piston skirt outer diameter 38.955-38.970mm 38.90mm
PISTON PIN, Piston pin hole inner diameter 12.002-12.008mm 12.03mm
PISTON RING Piston pin outer diameter 11.994-12.000mm 11.98mm
CYLINDER TO PISTON CLEARANCE 0.002-0.014mm 0.03mm
TROUBLESHOOTING
Comperssion low
● Worn cylinder or piston rings
● Leaking valve seats
Excessive smoke
● Worn cylinder or piston
● Improper installation of piston rings
● Scored or scratched piston or cylinder wall
Overheating
● Excessive carbon build-up on the piston combustion
● Incorrect spark plug
Knocking or abnormal noise

● Worn piston and cylinder
● Excessive carbon build-up
● Low octane fuel
8-1
FAN COVER, SHROUD REMOVAL

REMOVE
● Luggage box. ( 3-3 )
● Plug maintenance cover. ( 3-3 )
● Center cover. ( 3-3 )
● Floor side cover. ( 3-4 )
● Floor panel. ( 3-4 )
● Plug cap.
BOLT
BOLT
BOLT
● Loosen the 3 fan cover cover comp washer screws.

● Remove the fan cover element B.
FAN COVER ● Remove the fan cover rubber.
RUBBER ● Loosen the 2 fan cover flange bolts.
● Remove the fan cover toward the floor panel.
● Loosen the 2 left shroud flange bolts.
● Remove the left shroud.
FAN COVER COVER
·Pay attention not to damage certain part when

removing
·Remove according to the working precedure.
FAN COVER COMP.

SHROUD
8-2
CYLINDER HEAD/ CYLINDER/ PISTON

REMOVAL
● Exhaust muffler assembly. ( 3-7 )
● Fan cover shroud. ( 3-2 )
FLANGE BOLT
Cylinder Head
● Loosen the 4 cylinder head bolts.
·Bolts are loosened by rotating 2~3 times and

alternating to a diagonal bolt.
● Remove
- Cylinder head.
- Cylinder head gasket.
CYLINDER HEAD
Cylinder
● Remove the cylinder.
CYLINDER
Piston/Piston Ring
● Remove
- Piston pin clip.
PISTON - Piston pin.
·Be careful not to bend pins.

·Be careful not to damage the cylinder and crankcase
gasket face when cleaning.
PISTON PIN
8-3
REMOVE
● Piston.
● Piston ring.
● Expander.
● Needle bearing from the small end of the connecting
rod.
BEARING
·Do not damage or scratch the piston.

·Do not apply side force to the connecting rod.
·Do not let the clip fall into the crankcase.
·Mark and store the pistons and piston pins so that
they can be reinstalled in their original positions.
PISTON PIN CLIP PISTON PIN PISTON
INSPECTION
● There is more carbon deposit whitin the engine in case
of 2 cycle engine than 4 cycle engine because the
engine oil is burnt in the 2 cycle engine. Excessive
carbon deposit may cause self-ignition by the
overheating of the carbon in the combustion chamber
and the piston head and may damage the engine.
● Carbon deposit in the exhaust gas port disturbs exhaust
gas flow and causes decrease of the output. Remove
the carbon deposit periodically.
CYLINDER HEAD
·Pay attention not to damage the combustion

chamber, the piston and the cylinder when removing
the carbon.
● Remove the cylinder head and remove the carbon with

the piston being in the top dead center.
● Dismount the cylinder, remove the carbon deposited in
the exhaust gas port and clean the remaining carbon in
the cylinder.
CYLINDER
8-4
Cylinder Wear Inspection
● Inspect the cylinder wall for scratches and wear.
·Inspect the area near T.D.C (Top Dend Center)

carefully. This area is especially subject to wear due
to the possibility of borderline lubrication fro heat
and top ring compression.
● Measure and record the cylinder I.D. at the three levels

in both an X and Y axis.
● Take the maximum reading to determine the cylinder
wear.
·Avoid the intake and exhaust ports when measuring.
● Measure the piston O.D.

● Calculate the piston-to-cylinder clearance. Take the
maximum reading to detemine the clearance.
Piston Outer Diameter Inspection
● Measure and record the piston O.D. 90。to the piston

pin bore and at the point specified in the Model
Spectific manual, near the bottom of the piston skirt.
● Replace the piston if the service limit is exceeded.
● Calculate the piston-to-cylinder clearance
● Install the needle bearing and piston pin in the

connecting rod small end and check for excessive play.
● If the piston pin I.D. is over the service limit, the
crankshaft must be replaced. Measure the I.D. of the
connecting rod small end.
8-5
Piston Pin Inspection
● Measure the piston pin O.D. at three points.

● Replace the piston pin if the service limit is exceeded.
Piston Pin Bore Inspection
● Measure the piston pin bore I.D. in an X and Y axis.

Take the maximum reading to determine the I.D.
●Replace the piston if the I.D. is over the service limit.
PISTON/PISTON RING INSTALLATION

● Clean the piston ring grooves.
● Lubricate the piston rings and ring grooves with clean
2-stroke oil.
● Install the piston rings on the piston with the marks
facing up.
·Do not confuse the top and second rings. Be sure to

install them in the proper grooves.
·Some 2-stroke engines use an expander ring behind
the second ring.
● In 2-stroke engines, theh piston has stopper pins that

hold the piston rings away from the intake and exhaust
ports.
● Align the piston ring end gaps with the stopper pins.
● Check the fit of each ring in tis groove by pressing the
ring into the groove. Make sure that it is flush with the
piston at several points around the ring.
● If the ring rides on the stopper pin, it is damaged during
assembly.
8-6
● Coat the needle bearing (2-stroke engine only) and
piston pin with the recommended oil. Lubricate the
piston pin
2-Stroke engine : Recommended engine oil.
·Place a clean shop towel over the crankcase to

prevent the clip from falling into the crankcase.
● Install the needle bearing into the connecting rod.

● Install the piston and insert the piston pin.
·The mark that is stamped on the piston head should

be facing the correct direction.
“IN” MARK : TO INTAKE SIDE
“EX” or “▵”MARK : TO EXHAUST SIDE
● Install new piston pin clips.
·Always use new piston pin clips Reinstalling used

piston pin clips may lead to serious engine damage.
·Take care not to drop the piston pin clip into the
crankcase.
CYLINDER HEAD ·Set the piston pin clip in the groove properly.
·Do not align the clip’s end gap with the piston cutout.
CYLINDER/ CYLINDER HEAD

INSTALLATION
● Coat the cylinder wall and piston ring with clean
engine oil and install the cylinder.
·Be careful not to damage the piston ring.
● Install the cylinder head.
8-7
TRANSMISSION/CRANKSHAFT/CRANKCASE
R.CRANK CASE
CRANKSHAFT
L.CRANK CASE
COUNTER GEAR FINAL GEAR

COUNTER
SHAFT MISSION COVER
DRIVE SHAFT
9-0
9. TRANSMISSION/CRANKSHAFT/CRANKCASE
SERVICE INFORMATION 9-1 CRANKSHAFT REMOVAL 9-5

TROUBLESHOOTING 9-1 CRANKCASE BEARING REMOVAL 9-6
TRANSMISSION 9-2 CRANKSHAFT INSTALLATION 9-7
SERVICE INFORMATION
GENERAL SAFETY
● This section describes how to remove the crank case and to maintain the transmission and the crankshaft.
● Always use special tools to change the drive shaft. Fix the bearing inner race, andn install the shaft.
● The following parts must be removed prior to removing the crank case. Follow the removal procedure specified in each
section.
-OIL PUMP ( SECTION 4 )
-CARBURETOR ( SECTION 5 )
-ENGINE ( SECTION 6 )
-CYLINDER HEAD/ CYLINDER/ PISTON ( SECTION 8 )
-AC GENERATOR ( SECTION 13 )
-DRIVE PULLEY ( SECTION 7 )
-CLUTCH/DRIVEN PULLEY ( SECTION 7 )
-REED VALVE ( SECTION 5 ) 9
● The following parts must be removed prior to changing the L. crank case. Follow the removal procedure specified in
each section.
-TRANSMISSION ( SECTION 9 )
-REAR BRAKE ( SECTION 12 )
● To assemble the crank case and crankshaft, set the special tool to the inner race of the crankshaft bearing, and push and
assemble. Remove the bearing from the crankshaft during disassembling work, and insert a new bearing in the case.
Install the oil seal after the case is assembled.
SPECIFICATIONS
Large end side clearance 0.15~0.55mm 0.60mm
CRANK Connecting rod large end right angle direction clearance 0.010~0.02mm 0.04mm
SHAFT Right 0.03mm 0.15mm
Crank shaft shaking
Left 0.05mm 0.10mm
TROUBLESHOOTING
Engine Noise
● Clearance in the connecting rod large end portion/small end portion bearing.
● Clearance in the crankshaft bearing.
9-1
TRANSMISSION
DISASSEMBLY
● Remove
- L. side cover. ( 7-2 )
- Continuously variable transmission.
( SECTION 7 )
- Exhaust muffler. ( 3-7 )
- Rear wheel. ( 11-3)
● Install the oil sump under the cover of transmission.
● Loosen the 6 transmission cover flange bolts.
● Remove
MISSION COVER - Transmission cover.
- Mission cover guide ruber.
- Drive shaft from the transmission cover by using a
MISSION COVER SEAL hydraulic press.
·Take precautions not to damage the cover joints.
● Remove the oil seal of the drive shaft.
6203
BEARING
6202 BEARING
REMOVE
FINAL GEAR ● Final shaft gear.
● Thrust washer.
● Countershaft.
● Counter shaft gear.
● Side washer.
COUNTER SHAFT COUNTER GEAR
INSPECTION
● Inspect the drive shaft for wear or damage.
DRIVE SHAFT
9-2
● Inspect the final shaft for wear or damage.
FINAL GEAR
● Inspect the countershaft for wear or damage.
COUNTER SHAFT
COUNTER GEAR
Bearing Inspection
● Manually turn the bearing inner race installed inside

6203 the transmission cover, and check if the race is turning
BEARING smoothly.
● Verify the outer race is accurately installed in the case.
● Replace the bearing, if necessary.
·Install the bearing with the carved mark directing to

the outside.
6202 BEARING
● Use special tools to push in the bearing into the case.

DRIVER DRIVER
PILOT 20mm HANDLE A TOOLS : DRIVER HANDLE A
OUTER DRIVER 52X55mm
DRIVER PILOT 20mm
● Check the L. crank case oil seal for wear or damage.
OUTER DRIVER
9-3
TRANSMISSION ASSEMBLY
● Install the drive shaft on the transmission cover.
● Install a new drive shaft oil seal.
TOOL : CRANK ASSEMBLY
● Install the thrust washer, final gear and counter gear,

FINAL GEAR side washer on the L. crankcase.
COUNTER GEAR
● Install
- New dowel pins.
- New transmission cover seal on the transmission
cover.
- Transmission cover.
● Tighten the transmission cover with the flange bolts.
·Tighten bolts diagonally and alternately and tighten

with specified torque in the end.
MISSION COVER SEAL
● Remove the oil check bolt, release the transmission oil

filler ACG cap or the L. crankcase until the oil
overflow through oil hole and fill the recommended oil
slowly.
● Install the oil check bolt and the cap .
RECOMMENDED OIL : SAE #80~90

TRANSMISSION OIL AMOUNT : 0.09
OIL CHECK BOLT
9-4
CRANKSHAFT REMOVAL
● Loosen the 6 R. crankcase flange bolts.
● Secure a crankcase puller on the R. crankcase and
remove the R. crankcase from the L. crankcase.
TOOL : CRANKCASE PULLER(0751-00003)
● Secure a crankcase puller on the L. crankcase and remove

the crankshaft from the L. crankcase.
·Be careful not to distort the mating surface of the

crank case during disassembly.
·Do not force to disassemble by pounding on the
crankshaft.
TOOL : CRANKCASE PULLER(0751-00003)
● Remove the oil seal from the R. and L. crankcases.

● Remove the dowel pin.
CRANKSHAFT BEARING REMOVAL

● If the radial ball bearing is left on the crankshaft,
remove the bearings out of the crankshaft using a
bearing puller.
TOOL : UNIVERSAL BEARING PULLER(0755-00001)
CRANKSHAFT INSPECTION
● Place the crankshaft on a stand or V-block, and check
the journal vibration.
SERVICE LIMIT : RIGHT SIDE 0.1mm

LEFT SIDE 0.1mm
9-5
● Measure the side gap between the connecting rod big
end and the crank weight.
● Check the vertical shaft play of the connecting rod big

end from the X and Y direction.
CRANKCASE BEARING REMOVAL

● Remove the transmission and crankshaft.
INSPECTION
● Manually turn the bearing inner race to see if it rotates
smoothly.
● Check the outer race to see if it is accurately pressed
into the case.
● If the outer race is excessively loose, or is loosely
pressed into the case, remove in and replace with a new
CRANK BEARING one.
REPLACEMENT
L. Crankcase
OIL SEAL ● Use special tools to remove the drive shaft bearing.
TOOLS : BEARING REMOVER SET

REMOVER SHAFT
REMOVER HEAD
● Remove the final gear bearing and oil seal.

● Remove the counter gear bearing.
9-6
● Apply clean engine oil to a new bearing, and assemble
it to the crank case.
● Install a new final gear oil seal.
DRIVER
CRANKSHAFT INSTALLATION
HANDLE A ● Apply clean engine oil to the new R. crankshaft
bearing, and press in the bearing into the R. crank case.
DRIVER PILOT
20mm
TOOLS : DRIVER HANDLE A
OUTER DRIVER 52x55mm
OUTER DRIVER DRIVER PILOT 20mm
52X55mm
● Use special tools to assemble the crankshaft bearing to

the L. crank case.
TOOLS : DRIVER HANDLE A

OUTER DRIVER 52x55mm
DRIVER PILOT 20mm
● Clean the crankcase using cleaning oil, and check for

rack and damage to each area.
L. CRANK ·After removing the liquid gasket from the joining

CASE face of the crankcase, amend the scratched areas
using oil ston.
·Apply 2-cycle oil to the radial ball bearings and the
connecting rod large end portion.
● Install the crankshaft to the L. crankcase.
·Install not to interfere with the case with being

careful of connecting rod location.
CRANKSHAFT
ASSEMBLER TOOL : CRANKSHAFT ASSEMBLER
9-7
● Apply a liquid gasket to the L. crankcase joining face,
install the dowel pins.
● Install the R. crankcase.
CRANKSHAFT
● Install the 6 flange bolts.
ASSEMBLER
·Make sure that there is no adhesion of gasoline to the

R., L. crankcase liquid gasket face.
·Do not apply excessive liquid gasket fluid
excessively.
TOOL : CRANKSHAFT ASSEMBLER
1.0mm
CRANKSHAFT
ASSEMBLER
·Make sure that the crankshaft is rotated smoothly
after installation (prior to oil seal installation).
OIL SEAL
·If the smooth rotation is not acquired, tap the
crankshaft bearing part of crankcase with plastic
hammer to ensure proper installation without
mismatch.
L. CRANK CASE
5.0mm
● Install a new L. oil seal in the crankcase end portion at
1.0mm depth.
OIL SEAL
CRANKSHAFT
ASSEMBLER
● Install a new R. oil seal in the crankcase end portion at

R. CRANK CASE 5.0mm depth.
CRANKSHAFT
ASSEMBLER
9-8
MEMO
FRONT WHEEL/FRONT FORK/STEERING
STEERING HANDLE
STEERING STEM
FRONT FORK
FRONT BRAKE DISK
FRONT TIRE
FRONT CASTING WHEEL
10-0
10. FRONT WHEEL/FRONT FORK/STEERING
SERVICE INFORMATION 10-1 TUBELESS TIRE 10-9

TROUBLESHOOTING 10-2 FRONT FORK 10-14
STEERING HANDLE 10-3 STEERING STEM 10-20
FRONT WHEEL 10-5
SERVICE INFORMATION
GENERAL SAFETY
● Keep oil or brake fluid off the brake disk and pad because the contaminated brake disk and pad reduces the braking
performance. If contaminated, replace the pad with a new one, and clean the disk.
● Use special tire levers and rim protectors to remove or assemble tires to protect the rim from being damaged.
● This section describes how to remove and maintain front wheels, front fork and steering system. For information on the
front brake system, refer to section 10.
● Place a jack underneath the engine to support the 2-wheeled vehicle.
SPECIFICATIONS
FRONT AXLE DEFLECTION - 0.2mm 10
RADICAL - 2.0mm
FRONT WHEEL RIM RUNOUT
AXIAL - 2.0mm
FRONT FORK TUBE DEFLECTION - 0.2mm
FRONT FORK OIL LEVEL 58㎤ -
FORK SPRING FREE LENGTH 278.6mm -
TORQUE VALUES
STEERING STEM LOCK NUT 7.0㎏·m
BRAKE DISK BOLT 3.9㎏f·m
FRONT AXLE NUT 6.0㎏f·m
10-1
TROUBLESHOOTING
Hard steering
● Steering bearing adjustment nut too tight.
● Faulty steering stem bearings.
● Damaged steering stem bearings.
● Insufficient tire pressure.
Steers to one side or does not track straight

● Unevenly adjusted right and left shock absorbers.
● Bent front forks.
● Bent front axle : wheel installed incorrectly.
Front wheel wobbling

● Bent rim.
● Worn front wheel bearings.
● Faulty tire.
● Axle nut not tightened properly.
● Wheel out of balance.
Soft suspension
● Weak fork springs.
● Insufficient fluid in front forks.
Hard suspension
● Incorrect fluid weight in front forks.
● Front fork air pressure incorrect.
● Bent fork tubes.
● Clogged fluid passage.
● Clogged anti-dive orifice.
Front suspension noise

● Worn slider or guide bushings.
● Insufficient fluid in forks.
● Loose front fork fasteners.
● Lack of grease in speedometer gear box.
10-2
STEERING HANDLE
STEERING
STEERING
STEERING HANDLE
HANDLE
HANDLE
● Remove
- Wind screen.
- Front cover.
- Wire coupler
● Loosen
- Throttle housing fixing pin screw.
● Remove
- Throttle upper/under housing.
- Throttle grip.
● After fixing the master cylinder and then loosen the
two flange bolts, remove the master cylinder.
MASTER
MASTER
MASTER CYLINDER
CYLINDER
CYLINDER
·Support master cylinder properly to prevent brake

fluid from leaking.
·If the master cylinder is dropped upside down, air
may enter the hydraulic system. Fix it to the vehicle
while maintaining the correct assembled location.
● Loosen the handle bracket fixing washer bolt.

● Remove
- Handle bracket bend.
- Handle bracket.
FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT - L. handle grip.
● Loosen the handle setting U-nut, remove the handle set

HANDLE
HANDLE
HANDLE BRACKET
BRACKET
BRACKET collar and flange bolt.
● Remove the rear brake cable, front brake hose,
speedometer cable, handle cable from the guide.
● Remove the steering handle from the steering stem.
INSTALLATION
● Install steering handle to the steering stem.
● Install the handle setting bolt, U-nut, handle set collar.
·When installing the handle setting collar, match it

with the groove accurately.
HANDLE
HANDLE
HANDLE SETTING
SETTING
SETTING BOLT
BOLT
BOLT
10-3
● Install the rear brake cable, front brake hose,
STEERING
STEERING
speedometer cable to the handle cable guide.
STEERING HANDLE
HANDLE
HANDLE
● Apply DAELIM Bond A to the inside surface of the
grip and to the clean surface of the left handle bar. Wait
3~6 minutes and install the grip.
(Bond A :ROYAL BOND 1300)
·Clean the bonding surface to avoid oil, grease or

gasoline from attatching.
·Leave it for minimum 1 hour until the bond is dried.
·Use the bond according to the bond manual enclosed
and install the grip while rotating it before the bond is
HANDLE
HANDLE
HANDLE SETTING
SETTING
SETTING COLLAR
COLLAR
COLLAR dried completely.
HANDLE
HANDLE GRIP
HANDLE GRIP
HANDLE GRIP
GRIP ● Align the positioning pin with the handle hole and
install the L. handle bracket.
TORQUE : 1.2kgf·m
● Clean the throttle grip surface, apply the grease and

install the grip.
● Connect the throttle cable to the groove of the grip.
● Tighten the pin screws after assembling the under and
upper throttle housings.
·Check the throttle grip for smooth operation and

adjust the free play to 2~6mm.
MASTER CYLINDER ● Match the master cylinder with the punch mark of the
handle, install it with the mark in the master cylinder
THROTTLE HOUSING holder facing upwards or front and tighten the rear or
front first.
·Check to see if the cylinder is passing each cable and

wire harness directly and make sure that there is any
interference by rotating the handle to the right and
PUNCH left.
MARK
INSTALL
● Rear handle cover.
● Front handle cover.
● Front cover.
10-4
SPEEDOMETTER
SPEEDOMETTER
SPEEDOMETTER CABLE
CABLE
CABLE FRONT WHEEL
REMOVAL
● Remove screws from the speedometer gear box, and
separate the speedometer cable.
·Loosen axle nuts. Support bottom of engine with a

jack until the front wheel is lifted.
SPEEDOMETTER
SPEEDOMETTER GEAR
SPEEDOMETTER GEAR BOX
GEAR BOX
BOX
● Loosen the axle nut.

● Remove the front axle.
● Remove the front wheel.
·Do not operate brake lever after the front wheel is

removed.
● Remove the speedometer gear box.
FRONT
FRONT
FRONT AXLE
AXLE
AXLE
INSPECTION
● Check the front axle for deflection. Place the front axle
on a V-block, and measure deflection with a dial gauge.
● Place the front wheel on an inspection stand. Slowly

DIAL
DIAL GAUGE
DIAL GAUGE
GAUGE turn the wheel, and check the rim runout with a dial
gauge.
SERVICE LIMIT : Radial 2.0mm

Axial 2.0mm
10-5
Bearing Inspection
● Manually turn the bearing inner race, and replace if it

makes noise or is worn. Check if the bearing outer race
is accurately fitted into the wheel hub, and replace
worn ones.
·Replace bearings in pairs (left and right set).
FRONT WHEEL DISASSEMBLY

● Remove
- Speedometer gear box.
- Dust seal.
- Speedometer gear retainer.
SPEEDOMETER GEAR BOX
● Remove the front brake collar A.
FRONT BRAKE
COLLAR A
● Remove te dust seal and brake disc.

● Check the disc for defects.
FRONT BRAKE DISK
10-6
WHEEL BEARING REPLACEMENT
BEARING
REMOVER HEAD ● Install the bearing remover head and the remover shaft
on the wheel, and remove the bearing and distance
collar.
BEARING
REMOVER ·Always replace bearings in pairs, and never use old
bearings.
TOOLS : BEARING REMOVER HEAD

BEARING REMOVER
● Apply sufficient amount of grease to the bearing.

● Insert the right bearing with its seal surface facing
outside.
● Do not tilt the bearing. Insert accurately.
● Upon assembling the distance collar, insert the left
bearing with its seal surface facing outside.
TOOLS : DRIVER
ATTACHMENT, 32x35mm
PILOT, 15mm
·The bearing inserted in the last must be inserted until

it contacts with the distance collar.
·Excessively inserted bearing can cause damage the
opposite side bearing.
SPEEDOMETER GEAR REPLACEMENT

● Remove the speedometer gear and washer from the
speedometer gear box.
● Check the gear for wear or damage.
● Install the washer.
● Apply grease to the speedometer gear prior to
assembling.
SPEEDOMETER GEAR SPEEDOMETER

GEAR BOX
10-7
TIRE
DISTANCE COLLAR
NUT RADIAL BEARING
SPEEDOMETER GEAR BOX R. SIDE COLLAR
BRAKE DISK
OIL SEAL RADIAL BEARING

AXLE
RIM
FRONT WHEEL ASSEMBLY

● Apply grease to the right side dust seal rim.
● Install the right side dust seal.
● Install the brake disk.
● Install disk bolts.
TORUE VALUE : 3.9kgf·m
BRAKE DISK
● Install the front brake collar A.
FRONT BRAKE COLLAR A
● Align the wheel hub tangs with the slots of the

speedometer gear retainer, and assemble the
speedometer gear box seal.
10-8
● Apply grease to the dust seal rim.
● Install the dust seal, and align the tangs of the
speedometer gear retainer with the gear groove to
assemble the speedometer gear box.
TUBELESS TIRE
REMOVAL
● Remove the wheel.
·Single brake disk type : To prevent damage to the

disk, place the wheel on the level surface with the
disk facing up.
·Double brake disk type : Remove one disk first, then
place the wheel on the level surface with the other
disk facing up.
● Remove the valve cap and bleed air by pressing the

valve core.
● Remove the valve core after bleeding air completely.
● Remove the valve stem nut and push the valve stem
lightly.
● If a bead stopper is installed, loosen the lock nut and
push the bead stopper down.
● Collapse in the bead with a tire bead breaker.
● If no tire bead breaker is available, step on the side wall
to collapse the bead.
·Do not step on the rim.
● Collapse the bead into the rim center and slide the tire
out of position.
·Tire can be easily removed once the beads are

collapsed completely.
● Apply a mild detergent solution to the rim and tire

mating surfaces.
10-9
● Be sure that the bead is completely collapsed.
● In case of the tube type tire, insert the tire lever from
the opposite side of the valve and raise the bead over
the rim.
● On tubeless tires, insert the tire lever from the valve
side and raise the bead over the rim.
● Always use a rim protector when using tire levers.
·To avoid damaging the rim when using the tire lever,
always use rim protectors.
·Be sure to use motorcycle tire levers.

·Do not apply the mild detergent solution to the rim
and tire mating surfaces of low pressure tire. Apply
water only.
● Insert another tire lever at 30~50mm from the first tire

lever and remove the tire from the rim, little by little.
·Do not try to remove the bead too much at one time.
·Do not pry against or scratch the bead stopper area
with the tire lever.
● Repeat the above procedures until half of bead is

removed. Then remove the remaining bead by hand.
● Remove the tire from the rim.
10-10
RIM VALVE REPLACEMENT
● Cut off the rim valve at its base.
● Apply mild detergent solution to a replacement rim
valve and insert it from inside of the rim.
·Be sure to use the recommended rim valve.

·Do not damage the valve hole.
·Replace the rim valve whenever installing a tubeless
tire.
RIM INSPECTION
● For a tube type tire, check the rim band and rim lock to
be sure they are installed properly.
·Any attempt to mount passenger car tires on a

motorcycle rim may cause the tire bead to separate
from the rim with enough explosive force to cause
serious injury or death.
·Always change rims which have been bent or have

cracks, as they may cause air leakage.
·Always change the rim if there are any flaws over
0.5mm in depth and 1.0mm in width on the surface
touching the bead.
● Check the tire for overall condition and use a mild

detergent solution on the bead.
TUBELESS TIRE INSTALLATION

● Use only water as a lubricant when removing or
mounting tires.
● Soap or other tire lubricants may leave a slippery
residue that can cause the tire to shift on the rim.
·A tire that shifts on the rim may lead to a sudden loss

of air pressure while riding and an accident could
occur.
·Be sure to use motorcycle tire levers.

·Do not use the detergent solution on low pressure
tires. Use water only.
10-11
● If the tire has an light mark (yellow paint mark), install
the tire with this mark aligned with the valve.
● If the tire has an arrow mark, install the tire with the
mark pointing in the direction of rotation.
● Stand the tire upright, hold it with one hand and,
starting from the opposite side to the valve, install one
side of the tire on the rim as much as you can by hand.
● Be sure to assemble in the sequence shown.

● Place the wheel on the level surface and install the
remaining portion of the tire using two tire levers.
·For easy assembly, apply a mild detergent solution to

the tire and rim mating surfaces.
·Do not use the detergent solution on the tire and rim
mating surfaces of the low pressure tires. Use water
only.
● Install the other side of the bead while holding the

assembled portion of the bead with your knee to
prevent it from coming off.
·Before using the levers, be sure that the bead on the

opposite side is positioned in the center of the rim.
● Install the bead a little at a time; using care not to

damage the tube or wheel with the tire levers.
● After 1/2 of the bead has been installed, insert the two
tire levers at a distance of 30~40mm to install it.
Repeat this procedure until 3/4 of the bead has been
installed.
·Hold one tire lever upright to remove the other lever.
10-12
● After 3/4 of the bead has been installed, check the bead
on the opposite side. Be sure it is still in the center of
the rim.
·The last portion of the bead is more difficult to

install. The rim and bead may be damaged if the
bead on the opposite side of the point where you are
working is not in the rim center.
● When the remaining bead is only 50~60mm, pull the

two levers up and over.
● Apply a mild detergent solution to the bead again.
·Use only water as a lubricant when removing or

mounting tires. Soap or other tire lubricants may
leave a slippery residue which can cause the tire to
shift on the rim.
● Tap on the tire tread surface with a rubber hammer so

that the tire and rim fit evenly around the
circumference.
● Be sure that the tire center and rim center are aligned.
● Inflate the tire to 1.5 times the standard recommended

pressure to seat the bead on the rim.
·Use the tire pressures specified in the Model Specific

manual or on the tire label. Overinflation may cause
a tire to burst with sufficient force to result in serious
injury or death.
10-13
·For tubeless tires, you may hear a loud sound as the

bead seats onto the rim. This is normal.
·For tubeless tires, if air leaks out from between the
rim and bead, let the wheel stand with the valve at
the bottom and put air in while pushing down on the
tire.
● Check that the tire bead seats on the tire rim securely
and the rim line of the tire is concentric with the rim.
● Adjust the tire pressure to the specified pressure.
● Check the wheel balance.
FRONT WHEEL INSTALLATION

● Insert the front wheel between the front forks.
● Insert the disk, taking precautions not to damage the
pad, and assemble the wheel.
● Align the slots of the speedometer gear with the tangs
of the left fork slider.
● Insert the front axle into the speedometer gear box and
the wheel hub.
● Install the axle nut.

● Assemble the speedometer cable, and tighten with
screws.
● Place the front wheel on the ground, and tighten the
axle nut to the prescribed torque.
FRONT
FRONT BRAKE
FRONT BRAKE CALIPER
BRAKE CALIPER
CALIPER
FRONT FORK
REMOVAL
● Remove
- Front cover. ( 3-5 )
- Front fender. ( 3-5 )
- Front brake caliper. ( 12-7 )
- Front wheel. ( 10-5 )
● Loosen the front brake hose stay bolt, remove the L.
fork.
● Speedometer cable from R. fork speedometer cable
SPEEDOMETER CABLE guide.
● Loosen the R. fork securing bolt, remove the
speedometer cable and guide.
10-14
● Loosen the 2 steering stem front fork R., L. stay bolts.
● Remove the front fork.
FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT
FRONT FORK DISASSEMBLY

● Remove the fork tube cap bolt.
FORK BOLT
·If the screw is completely loosened, the fork tube cap

SPRING bolt may spring out by the force fo the spring. Take
due precautions.
·Remove the fork spring, and expand and release the
fork pipe several times to drain fork oil.
● Wrap the bottom case with a piece of cloth, and

remove the socket bolt.
10-15
·If the socket bolt turns idle but cannot be removed,

temporarily assemble the spring and the fork tube
cap bolt first.
·Hold the bottom case firmly with a vise, taking
precautions not to distort or damage it.
● Remove the dust seal.
DUST SEAL
● Remove the oil seal stopper ring.
OIL SEAL
STOPPER RING
● Remove the oil seal.
·Take precautions not to damage the interior and

exterion rim of the bottom case.
OIL SEAL
10-16
● Remove the fork tube from the bottom case.
● Remove the piston and rebound spring from the fork
tube.
FRONT FORK INSPECTION

● Place the fork spring on a level place, and measure the
free length.
FREE LENGTH ● If the free length deviates from the service limit,
replace the spring with a new one.
● Check components for damage or abnormal wear.
Replace defective parts with new ones.
SERVICE LIMIT : 243mm
FORK SPRING ● Place the fork tube on a V-block, and measure

deflection with a dial gauge.
SERVICE LIMIT : Replace if the deflection is greater

than 0.2mm
● Check the slider bush contact face.

● If the slider bush is extensively damaged, replace the
bottom case.
FRONT FORK ASSEMBLY

● Wash parts with clean oil prior to assembling.
● Assemble the rebound spring and thd fork piston to the
fork tube.
● Assemble the fork tube to the bottom case.
10-17
● Wrap the bottom case with a piece of cloth, and fix it to
the vise.
● Apply screw locking agent to the socket bolt thread,
and assemble the socket bolt to the fork piston.
·When a vise is used to hold the bottom case, do not

insert the case itself but insert the bracket.
SOCKET BOLT
● Apply ATF to a new oil seal.

● Assemble the oil seal to the bottom case.
● Insert the oil seal with special tools until the attachment
groove of the bottom case set ring is exposed.
TOOLS : FORK SEAL DRIVER

FORK SEAL DRIVER BODY
● Install the set ring.

● Accurately assemble the set ring to the bottom case.
● Install the dust seal.

● Fill a prescribed amount of automatic transmission
fluid(ATF) into the fork tube.
CAPACITY : 58cm3
● Slowly press the fork tube 2-3 times to discharge air.
10-18
● Assemble the spring to the fork pipe.
FREE LENGTH
·Install the spring with the smaller pitch side facing
downward.
FORK SPRING
● Assemble the fork bolt to the fork tube.
FORK BOLT
FRONT FORK INSTALLATION

STEERING
STEERING
STEERING STEM
STEM
STEM ● Install the front fork to the steering stem.
● Install the front fork setting bolt.
FLANGE
FLANGE
FLANGE BOLT
BOLT
BOLT
● Install the following parts.
- Front wheel ( 10-5 )

- Brake caliper ( 12-7 )
- Front fender ( 3-5 )
- Front cover ( 3-5 )
10-19
STEERING STEM
REMOVAL
● Front cover.
STEERING LOCK ● Front fender.
NUT SOCKET ● Front handle cover/rear handle cover.
● Steering handle.
● Front wheel.
● Front brake caliper.
● Front fork.
● Loosen the steering stem lock nut.

● Remove the speedometer cable and front brake hose
from the steering stem bracket.
● Loosen the steering top cone race.
● Remove the steering stem.
STEERING
TOP CONE RACE
SOCKET
·Place steel ball in a pan to prevent from being lost.

STEEL BALL
● Check the steel ball, cone race, and ball race for wear
or damage. Replace worn or damaged ones.
● Remove the steering steel ball/ upper steering ball race/

steering bottom cone race.
UNDER
BALL RACE
STEEL BALL
BOTTOM
CONE RACE
10-20
● Remove the upper ball race/ steering bottom cone race.
TOOL : BALL RACE DRIVER
·Check all of the races and balls for damage or

BALL RACE abnormal wear and replace as necessary.
DRIVER ·If the vehicle has been involved in a collision, the
steering stem may be damaged.
STEERING STEM INSTALLATION

● Insert the upper/under ball race into the steering head
pipe.
● Using a steering stem driver, drive the steering stem

bottom cone race into the steering stem.
BOTTOM CONE
RACE
● Insert the ball race after applying grease thereto.
10-21
● Install the top cone race and the steering head top
thread nut on the steering head.
● Tighten the top thread nut completely, and loosen by
1/8 turn.
STEERING LOCK
NUT SOCKET TORQUE VALUE : 1.0㎏f·m
● Check the top and bottom free play, and check for
smooth left and right movement.
● Temporarily install the R/L front forks first, and tighten

the steering stem nuts.

TOOLS : LOCK NUT WRENCH
EXTENSION BAR
SETTING BOLT
● Install the front fork.
● Install the following parts.
- Steering handle ( 10-3)

- Front wheel ( 10-5 )
- Front handle cover/ rear handle cover ( 3-6 )
- Front fender ( 3-5 )
- Front brake caliper ( 12-7 )
·Check the cables and wiring for interference.

CALIPER
CALIPER
CALIPER
● Install the front cover.
FRONT
FRONT COVER
FRONT COVER
COVER
10-22
11. REAR WHEEL/BRAKE/SUSPENSION
SERVICE INFORMATION 11-1 REAR BRAKE 11-4

TROUBLESHOOTING 11-2 REAR CUSHION 11-6
REAR WHEEL 11-3
SERVICE INFORMATION
GENERAL SAFETY
● If the brake drum or lining is contaminated with oil, braking power will be lost. If contaminated with oil, clean the brake
drum, and replace the brake shoe.
● Inhaled asbestos fibers have been found to cause respiratory disease and cancer. Never use an air hose or dry brush to
clean brake assemblies. Use a brake cleaner, designed to minimize the hazard caused by airborne asbestos fibers.
SPECIFICATIONS

AXLE SHAFT RUN OUT - 0.2 mm
RADICAL - 2.0 mm
REAR WHEEL RIM RUNOUT
AXIAL - 2.0 mm
REAR BRAKE DRUM INNER DIAMETER 110.0~110.3mm 111.0mm
REAR BRAKE LINING THICKNESS 4.0 mm 2.0 mm
REAR CUSHION SPRING FREE LENGTH 220.6mm -
11
TORQUE VALUES :
AXLE SHAFT RUN OUT 10.0~12.0㎏f·m
REAR CUSHION UPPER BOLT 3.5~4.5㎏f·m
REAR CUSHION LOWER BOLT 3.5~4.5㎏f·m
11-1
REAR WHEEL/BRAKE/SUSPENSION
TROUBLESHOOTING
Wobble or vibration in motorcycle
● Tire pressure incorrect
● Faulty tire
● Bent rim
● Loose wheel bearing
● Swing arm bushing worn
● Wheel out of balance
Soft suspension
● Weak springs
● Rear damper improperly adjusted, oil leakage
Hard suspension
● Rear damper improperly adjusted
● Bent shock absorber rod
Suspension noise
● Loose fasteners
● Worn shock
11-2
REAR WHEEL
REMOVAL
● Support the motor cycle on the main stand.
● Loosen the rear brake adjuster, and remove the brake
cable.
● Remove the brake arm joint B.
BRAKE ARM JOINT B ADJUST NUT
● Remove
U NUT - Muffler. ( 3-7 )
- Rear wheel mud guard.
● Loosen the rear wheel U nut.
● Remove
- Washer.
- Rear wheel.
REAR WHEEL
INSPECTION
● Turn the wheel, and check the rim for wobbles.
SERVICE LIMIT : Radical 2.0mm

Axial 2.0mm
DIAL GUAGE
INSTALLATION
● Insert the rear wheel over the final shaft.
FINAL SHAFT
11-3
● Insert the washer, and tighten with the U nut.
U NUT
TORQUE VALUE : 6.0~8.0kgf·m
INSTALL
● Brake arm joint B.
● Rear brake cable.
● Rear brake rod adjusting nut.
● Rear wheel mud guard.
● Muffler.
ADJUST NUT
REAR BRAKE
● Remove the rear wheel. ( 11-3 )
Y
INSPECTION
● Measure the brake drum of inner diameter
X
SERVICE LIMIT : 111mm
REAR WHEEL
● Measure the thickness of the brake lining.
BRAKE LINING
THICKNESS
11-4
REAR BRAKE DISASSEMBLY
● Manually open the brake shoe and remove it.
BRAKE SHOE ● Remove the shoe spring from the brake shoe.
SHOE SPRING
SHOE SPRING
BRAKE CAM
BRAKE SHOE
● Loosen the rear brake arm fixing bolt.

● Remove the rear brake arm, rear brake indicator, brake
cam, dust seal.
● Remove the rear brake cam.
REAR BRAKE ARM
REAR BRAKE ASSEMBLY/INSTALLATION

● Apply small amount of grease to the brake cam.
● Install the brake cam.
● Install the rear brake dust seal, indicator, rear brake
arm.
·Align the punch marks of the brake arm and the

brake cam before assembly.
·Remove the excessive grease after assembling the
shoe.
BRAKE SHOE
INSTALL
● Brake shoe and spring.
● Rear brake shoe to the rear brake cam.
● Rear wheel.
● Washer and U nut.
·Check the brake for smooth operation.
11-5
REAR CUSHION
REMOVAL
REAR CUSHION ● Remove the plug maintenance cover/ center cover.
( 3-3 )
SETTING ● Remove the luggage box. ( 3-3 )
BOLT ● Remove the body cover. ( 3-3 )
● Loosen the top and bottom rear cushion setting bolts.
·Support the frame firmly prior to working.
DISASSEMBLY
● Install the compressor attachment as shown in the
figure.
● Install the cushion on the cushion compressor, and
compress the spring.
TOOLS : COMPRESSOR ATTACHMENT

REAR COMPRESSOR
● Fix the bottom metal, and loosen the lock nut.

● Remove the bottom metal.
● Remove the stopper rubber, spring from the damper
BOTTOM component.
METAL
INSPECTION
● Measure the rear cushion spring free length.
SPRING
● Check the damper rod for deflection or damage.
FREE LENGTH
11-6
REAR CUSHION ASSEMBLY/INSTALLATION
● Assemble the spring, spring guide, and stopper rubber.
·Install the spring with its narrow pitch side facing

upward
● Apply thread locking agent to the lock nut, and install

the rear cushion compressor attachment on the damper
rod.
● Fix the upper joint, and tighten the lock nut.

TOOLS : REAR CUSHION COMPRESSOR
REAR CUSHION COMPRESSOR ATTACHMENT
● Install the rear cushion.

● Tighten the top and bottom of the cushion with bolt.
REAR CUSHION
TORQUE VALUE : UPPER SIDE 3.5kgf·m
LOWER SIDE 3.5kgf·m
11-7
BRAKE SYSTEM
12-0
12. BRAKE SYSTEM
SERVICE INFORMATION 12-1 BRAKE DISK INSPECTION 12-6

TROUBLESHOOTING 12-1 BRAKE CALIPER 12-7
BRAKE FLUID/BLEEDING 12-3 MASTER CYLINDER 12-9
BRAKE PAD REPLACEMENT 12-4
SERVICE INFORMATION
GENERAL SAFETY
● Do not allow foreign material to enter the system when replenishing brake fluid.
● To prevent chemical changes, do not mix different types of brake fluid.
● Do not use the old brake fluid again.
● Brake fluid can cause damage to painted, plastic, and rubber surfaces. Take precaution not to allow parts to be
contaminated by the brake fluid.
● Do not reuse sealing washers.
● Clean the disassembled parts with brake fluid, and check for any clogged passage with compressed air.
● Bleed the brake hose after removing it.
TROUBLESHOOTING
HYDRAULIC DISK BRAKE
Braking power unsatisfactory Hard brake lever movement or unsatisfactory
● Air in the brake system. return
● Moisture in brake fluid ● Brake system clogged
● Brake pad and disk contaminated. ● Caliper piston seized or worn 12
● Caliper piston seal worn ● Unsatisfactory caliper sliding part operation
● Master cylinder piston seal worn ● Brake fluid line clogged
● Brake pad worn ● Caliper piston seal worn
● Caliper inside contaminated ● Master cylinder piston seized or worn
● Unsatisfactory caliper sliding part operation ● Brake lever bent
● Lopsided wear of brake pad and disk
● Low brake fluid level Brake drag
● Clogged brake fluid line ● Brake pad and disk contaminated
● Disk bent or distorted ● Improper wheel alignment
● Caliper piston seized or worn ● Lopsided wear of brake pad and disk
● Master cylinder piston seized or worn ● Disk bent or distorted
● Disk worn ● Unsatisfactory caliper sliding part operation
● Master cylinder inside contaminated ● Hydraulic system contaminated with dust.
● Brake lever bent
12-1
BRAKE SYSTEM
MECHANICAL DRUM BRAKE
Poor brake performance
● Improperly adjusted brake
● Worn brake linings
● Worn brake drum
● Worn brake cam
● Improperly installed brake linings
● Brake cable sticking/needs lubrication
● Contaminated brake linings
● Contaminated brake drum
● Worn brake shoes at cam contact areas
● Improper engagement between brake arm and camshaft serrations
Brake lever hard or slow to return

● Worn/broken return spring
● Improperly adjusted brake
● Sticking brake drum due to contamination
● Worn brake shoes at cam contact areas
● Brake cable sticking/needs lubrication
● Worn brake cam
● Improperly installed brake linings
Brake squeaks
● Worn brake linings
● Worn brake drum
● Contaminated brake linings
● Contaminated brake drum
12-2
BRAKE SYSTEM
MASTER
MASTER CYLINDER
MASTER CYLINDER
CYLINDER
BRAKE FLUID/BLEEDING
MASTER CYLINDER
BRAKE FLUID CHANGE
·A contaminate disk or pad reduces braking power.

Do not allow the disk or pad to be contaminated by
oil.
·Replace contaminated pads, and remove pollutants
from the disk completely.
·Check the brake fluid level often, and replenish new

fluid as required. Do not spill fluid on painted, plastic
or rubber parts.
● Remove the front handle cover. ( 3-6 )

● Remove the master cylinder cap, master cylinder
holder, and diaphragm from the master cylinder.
● Connect the bleeder hose to the bleeder valve. Loosen
the bleeder valve, and pump the brake lever repeatedly.
● When there is no more fluid flowing out of the bleeder
valve, stop pumping the brake lever.
FRONT
FRONT CALIPER
FRONT CALIPER
CALIPER AIR BLEEDING
● Fill the reservoir with DOT 3 or 4 brake fluid up to the
BLEEDER VALVE upper level.
·To prevent chemical changed, do not use different

types of brake fluid.
● Connect the recommended brake bleeder to the bleeder

valve.
● Loosen the bleeder valve while pumping the brake
lever.
● Repeat this operation until the brake fluid flows out of
the brake bleeder.
RESERVOIR
RESERVOIR
RESERVOIR INSIDE
INSIDE
INSIDE
·Check fluid level often, and replenish fluid if the
amount of fluid is reduced to the lower level.
·Read the user’s manual carefully prior to
disassembling or using the brake bleeder.
·Protect the bleeder valve with tape to prevent air
from entering the bleeder valve.
● Repeat the above operation until there is no air flowing

out of the bleeder hose.
● Squeeze the bleeder valve and operate the brake lever
to check the ingress of air.
● Add brake fluid.
BRAKE
BRAKE
BRAKE LEVER
LEVER
LEVER
12-3
BRAKE SYSTEM
● If the brake bleeder is not used, do the following,
MASTER
MASTER CYLINDER
MASTER CYLINDER
MASTER CYLINDER
CYLINDER ● First, fill the brake fluid up to the upper limit line.
● Connect the hose to the bleeder valve to receive brake
fluid.
① Squeeze the brake lever completely loosen the
bleeder valve 1/2 turn, and tighten it again.
·Do not release the brake lever unitl the bleeder valve
is tightened.
② Release the brake lever slowly to its fullest extent,

and leave it unattended for a few seconds.
③ Repeat the process specified in item ① and ②
until there is no more air bubbles coming out of the
bleeder valve.
● Check the fluid level often, and add fluid if the fluid
level is near the lower level.
● If no air leaks out of the bleeder hose, operate the brake
lever to check the presence of air.
● Assemble the bleeder valve.
TORQUE : 0.6kgf·m
FRONT
FRONT
FRONT CALIPER
CALIPER
CALIPER
● Add brake fluid up to upper level. Install diaphragm

and mater cylinder cap.
BRAKE PAD REPLACEMENT
·When replacing brake pads, replace whole set.

·Do not remove the brake hose when replacing brake
pads.
HANGER
HANGER
HANGER PIN
PIN
PIN
● Loosen the hanger pin.
12-4
BRAKE SYSTEM
● Loosen the 2 front brake caliper fixing bolts from the
FLANGE BOLT
FLANGE
FLANGE BOLT
BOLT
front fork.
● Remove the front caliper.
● To install a new brake pad into the brake, press the

piston to return to the original position.
● Remove the hanger pin, pad shim, and brake pad.
BRAKE PAD
BRAKE
BRAKE PAD
PAD
● Verify that the pad spring is installed in specific

position.
PAD
PAD SPRING
PAD SPRING
SPRING
● Install a new brake pad, pad shim, and hanger pin.

HANGER
HANGER
HANGER PIN
PIN
PIN
12-5
BRAKE SYSTEM
● Install the brake caliper into the left front fork.
FLANGE BOLT
FLANGE
FLANGE BOLT
BOLT
·Be careful not to damage the brake pad.
● Tighten the caliper braket bolt.
TORQUE : 2.7kgf·m
● Tighten the hanger pin.
HANGER
HANGER PIN
HANGER PIN
PIN
BRAKE DISK INSPECTION

● Measure the thickness of the disk.
BRAKE DISK SERVICE LIMIT : 3.0mm
·Measure the brake disk thickness at the several

points and replace if the smallest measurement is less
then the specified service limit.
● Check the brake disk for bent and twist.
·Replace the brake disk if the disk for damage or

cracks.
DIAL GAUGE
12-6
BRAKE SYSTEM
BRAKE CALIPER
REMOVAL
● Remove the brake oil bolts and the brake hose from the
brake caliper.
● Remove the caliper from the L. front fork and remove
the pad spring, hanger pin and brake pad.
OIL BOLT
OIL
OIL BOLT
BOLT
BRAKE
BRAKE HOSE
BRAKE HOSE
HOSE
·Pay attention not to let the brake fluid adhere to the
parts because it can damage the painted surface.
·Wind the hose joint with cloth to prevent the brake
OIL
OIL
OIL BOLT
BOLT
BOLT fluid from leaking.
·Clean the removed parts with the brake fluid and
make sure that the each port isn’t clogged with the
compressed air.
·Keep the removed parts in order to avoid dust from
adhering.
DISASSEMBLY
CALIPER
CALIPER
CALIPER
● Remove the slide pin, the L. bracket, the pin bush, the
boot and the pin boot, and the pin bolt from the caliper.
● If there is any wear or damage in the boot, replace it
with the new one.
● Wind the caliper with cloth to prevent the piston or
brake fluid from leaking.
● Remove the piston from the caliper while blowing the
low-pressure air in the opening of the brake hose.
AIR
AIR
AIR GUN
GUN
GUN
·Never use the high-pressure air or bring the air gun

too close.
DUST
DUST SEAL
DUST SEAL
SEAL
·Never touch the inside of the caliper
● Disassemble the piston seal and the dust seal
·Pay attention not to damage the inner surface of the

caliper.
● Clean the piston and the inside of the caliper and

remove the oil from the seal groove.
PISTON
PISTON SEAL
PISTON SEAL
SEAL
12-7
BRAKE SYSTEM
BRAKE CALIPER INSPECTION
Caliper Cylinder
● Check the caliper cylinder bore for scoring, scratches

or other damage.
● Measure the caliper cylinder I.D. in X and Y axis at
serveral points.
● Replace the caliper cylinder if the largest measurement
is beyond the specified service limit.
CYLINDER
GAUGE SERVICE LIMIT : 27.10 mm
CALIPER
Caliper Piston
● Measure the caliper piston O.D. in X and Y axis at

several points.
● Replace the caliper piston of the smallest measurement
is less than the specified service limit.
SERVICE LIMIT : 26.84 mm
BRAKE CALIPER ASSEMBLY/INSTALLATION

LH. BRACKET BRAKE PAD
PAD SPRING ● Clean the piston seal and the dust seal with the brake
fluid and install them in the caliper. Install the piston in
the caliper with the groove side of the piston facing the
pad.
PISTON
HANGER PIN
·Make sure that each part is free from dust or dirt

before reassembly.
·Replace the dust seals and piston seals as a set
whenever they are removed.
·When cleaning with the brake fluid, use the specified
PISTON SEAL brake fluid.
DUST SEAL
● Apply the silicone grease to the pin bush.

● Connect the pin bush to the portion of the caliper.
● Install the pad spring in the caliper.
SLIDE PIN ● Install the caliper pin bolt and the slide pin in the
caliper.
● Install the brake pad and the hanger pin in the caliper.
BRAKE PAD
12-8
BRAKE SYSTEM
● Connect the brake hose to the caliper, and install 2
sealing washers and the brake hose bolt.
TORQUE : 3.5kgf·m
OIL
OIL
OIL BOLT
BOLT
BOLT
● Install the slide pin cap.
● Fill the brake fluid, and bleed air.
MASTER
MASTER
MASTER CYLINDER
CYLINDER
CYLINDER
MASTER CYLINDER
REMOVAL
● Remove the back mirror.
● Remove the rear handle cover. ( 3-6 )
● Disconnect the front brake switch wire.
● Drain the brake fluid.
● Remove the brake hose from the master cylinder.
FRONT STOP
FRONT
FRONT STOP SWITCH
STOP SWITCH
SWITCH
·Brake fluid causes damage to the painted, plastic or
rubber parts. Do not spill fluid on these parts.
MASTER
MASTER
MASTER CYLINDER
MASTER CYLINDER
CYLINDER
CYLINDER ·If contaminated, gently wipe off the fluid with a
piece of cloth or wash in water. Close hose joints
OIL
OIL
OIL BOLT
BOLT
BOLT properly to prevent leakage of brake fluid.
·Clean the disassembled parts with brake fluid, and
use compressed air to verify each passage is not
clogged.
·Do not allow the disassembled parts to be
contaminated by waste material or dust.
● Remove the master cylinder holder, and lift out the

master cylinder.
FRONT
FRONT
FRONT STOP
STOP
STOP SWITCH
SWITCH
SWITCH
BRAKE
BRAKE HOSE
BRAKE HOSE
HOSE
MASTER DISASSEMBLY
CYLINDER SET
MASTER
● Remove the front stop switch.
CYLINDER
● Remove the piston boot, cir clip from the master
HOLDER
cylinder.
PISTON TOOL : SNAP RING PLIERS
BOOT
CIR CLIP
12-9
BRAKE SYSTEM
● Remove the washer, piston, spring from the master
MASTER cylinder.
CYLINDER SET ● Clean the master cylinder, reserve, master piston with
MASTER the recommended brake fluid.
CYLINDER
HOLDER
PISTON
BOOT
CIR CLIP
MASTER CYLINDER INSPECTION

● Check the piston periphery for kink or scratch.
● Check the primary and secondary cups for wear.
● Measure the O.D of the master pin
·If there is any leak of fluid when installing new

piston, it may indicate the side wear of the cylinder
by the direction of the piston contacting face. In this
case, the master cylinder must be replaced also.
● Check the master cylinder for scores, scratches or nicks

and replace if necessary.
● Measure the master cylinder I.D. in X and Y axis at
several points.
MASTER CYLINDER ASSEMBLY/INSTALLATION
·Replace the piston, spring, cups and snap ring as a

set.
·Be sure that each part is free from dust or dirt before
reassembly.
·When cleaning with the brake fluid, use the specified
brake fluid.
● Coat the piston cup with the fresh brake fluid and
install it on the piston. Install the spring with its larger
diameter end toward the master cylinder.
12-10
BRAKE SYSTEM
● Install the primary cup with its concaved side toward
the inner side of the master cylinder.
● Install the snap ring.
TOOL : SNAP RING PLIERS
·When installing the cups, do not allow the lips to turn

inside out. (Refer to the drawing.)
·Note the installation direction of the snap ring.
·Be certain that the snap ring is seated firmly in the
groove.
● Install the rubber boot in the groove properly.
MASTER
MASTER
MASTER CYLINDER
CYLINDER
CYLINDER ● Install the master cylinder to the handle bar.
·Install the holder with its “UP” mark facing upwards,

and align the holder joint with the punch mark on the
handle bar.
·Tighten the holder upper bolt first.
● Install the brake hose to the master cylinder with 2 new

MASTER
MASTER CYLINDER
MASTER CYLINDER
MASTER CYLINDER
CYLINDER sealing washers and the hose bolt.
● Connect the brake stop swtich wire.

FILL
FILL THE
FILL THE
FILL THE
THE ● Fill the brake fluid, and bleed air.
BRAKE
BRAKE
BRAKE
BRAKE ● Install the rear handle cover. ( 3-6 )
FLUID
FLUID
FLUID
FLUID ● Install the front handle cover. ( 3-6 )
● Install the back mirror.
12-11
MEMO
13. CHARGING SYSTEM/A.C.GENERATOR
SERVICE INFORMATION 13-1 CHARGING SYSTEM INSPECTION 13-4

CHARGING DEVICES LOCATION 13-2 HEADLIGHT VOLTAGE INSPECTION 13-6
TROUBLESHOOTING 13-3 REGULATOR/RECTIFIER INSPECTION 13-6
BATTERY REMOVAL/INSTALLATION 13-4 A.C. GENERATOR 13-7
BATTERY INSPECTION 13-4 RESISTER INSPECTION 13-9
SERVICE INFORMATION
·Do not place flammable materials near battery when charging. This can be a fire hazard as hydrogen gas is created
during charging battery.
·Do not allow battery acid to come into contact with clothes, skin or eyes. Battery acid contact can cause burns or loss of
eye sight. If contact occurs, thoroughly clean with water, and if acid enters eyes, flush with water and see a doctor.
·If battery acid gets on clothing, as it can seep through or make a hole through the clothing and make its way to the skin,
make sure to change clothing that has come into contact with battery acid and wash the battery acid from the clothes.
·This vehicle has a maintenance-free(MF) battery. Because MF batteries use different charging equipment, take special
care when performing maintenance and especially when replacing parts. Not all regular battery equipment is
compatible with MF batteries.
·When charging the battery, remove the battery from the frame and do not open stopper.
·There is the possibility of damaging the regulator/rectifier, etc. if the terminal or coupler is separated/connected when
electricity is over flowing through the electrical devices. Make sure to turn the main switch OFF when performing
maintenance to the charging equipment.
● If the battery is allowed to repeatedly lose all its charge, is repeatedly over-charged, or if it is left in an un-charged state,
the battery can be damaged, its life can be reduced, or it can lose some of its strength. It is important to note here that the
battery will naturally last 2-3 years of noromal use, and although it will re-charge, its load is reduced, leading to a loss in
battery strength.
● It is possible for the battery to become overcharged from battery body load. If a battery cell becomes short-circuited and 13
if a state develops where voltage is not created between the terminals, the regulator will not operate and excessive
voltage will develops where voltage is not created between the terminals, the regulator will not operate and excessive
voltage will develop in the battery and normal cell electrolytes will decrease.
● If the vehicle is not used for a long period, make sure to chage the battery every three months. If not so, the battery
ability to store electricity is reduced.
● A new MF battery will not necessarily be ready for use in the vehicle with only the adding of battery acid. Make sure to
charge battery after the adding of battery water in the following instances :
-When open voltage (voltage between terminals) does not reach 12.4V after the adding of battery water : charge until
open voltage reaches at least 12. 8V.
-When battery acid temperature is under 0℃ : charge normally for 2-3 hours.
● See the part location drawing for the location of charging system parts. ( 13-2 )
● Follow the trouble shooting for charging equipment inspection. ( 13-3 )
● The charging equipment may ofter appear to be malfunctioning if the couplers or connectors are incorrectly attached.
Make sure to check these connections before starting maintenance work on the charging equipment.
13-1
CHARGING DEVICE LOCATION
START SWITCH
RESISTOR
COMB. & LOCK SW REGULATOR RECTIFIER
CDI UNIT

IG COIL
ACG. CORD COUPLER
A.C.GENERATOR
HIGH TENSION CORD
WHITE GREEN
YELLOW 7A FUSE GREEN
RED
A.C.GENERATOR REGULATOR/
RECTIFIER
LIGHTING SWITCH BATTERY
DIMMER
SWITCH
BLUE WHITE BROWN BROWN

AUTO-
GREEN /
BYSTARTER PINK
BLACK
RESISTER RESISTER
5W 6.7 30W 5.9
HEADLIGHT TAIL LIGHT METERLIGHT

(12V 35/35W) (12V 5W) (12V 1.7W)
13-2
TROUBLESHOOTING
Battery is Overcharged
● Headlight bulb is out.
● No headlignt beam wire.
● Headlight register is damaged (disconnected).
● Lighting switch is connected incorrectly.
● Regulator/rectifier is not grounded or connected incorrectly.
Problems with the Charging System
Measure battery voltage leakage. ABNORMAL

Inspect the body of the register/rectifier.
NORMAL NORMAL
Short-circuited harness.
Damaged main switch.
ABNORMAL
Check charge level. OVER 15V Regulator/rectifier is damaged.
UNDER 14V
OVER 14~15V Battery is damaged.
Check the voltage of the regulator/rectifier Wire harness is short-circuited.

ABNORMAL
battery lines and the ground line. Coupeler is connected incorrectly.
NORMAL
Check the changing coil with the regulator/

rectifier coupler charging coil. ABNORMAL Check the AC generator charging coil
NORMAL
AC generator coupler connected incorrectly.
NORMAL ABNORMAL
Damaged charging coil.
Check the lighting coil at the regulator/ ABNORMAL

Inspact the AC generator charging/
rectifier coupler lighting coil line. lighting coil
NORMAL
NORMAL AC generator coupler connected incorrectly.
ABNORMAL
Damaged charging/lighting coil.
Check the headlight lighting control voltage. ABNORMAL Damaged regulator/ rectifier
(darkened headlight)
NORMAL
Inspect the headlight register. ABNORMAL Damaged headlight register.
NORMAL
Inspect the body of the register/rectifier. ABNORMAL Damaged regulator/ rectifier.
NORMAL
Damaged Battery
13-3
BATTERY COVER BATTERY REMOVAL/INSTALLATION
● Loosen the battery cover setting bolt.
● Remove the battery cover.
● After removing the negative “⊖” terminal of battery
firstly, must remove the positive “⊕” terminal of
battery.
SETTING BOLT
BATTERY INSPECTION
CHARGE LEVEL (OPEN-CIRCUIT VOLTAGE)
INSPECTION
● Remove the battery cover and disconnect the battery
terminals.
● Measure the voltage between the battery terminals.
- FULLY CHARGED : 13.0-13.2V

- INSUFFICIENTLY CHARGED : Under 12.3V
·Use a digital voltmeter when measuring charge level.

: DAELIM PVA multi-tester
·Take special care not to deform the battery terminals.
TOOL : DIGITAL CIRCUIT TESTER
CHARGING SYSTEM INSPECTION

LEAK TEST
● Trun off the main switch, and remove the earth cable
from the battery. Connect an ampere meter between the
battery terminal and the earth cable, and check current
when the main switch is turned off.
·Use an ampere meter while sequentially changing its

measuring range from large to small. If the current
level greater than the measuring limit is measured,
the ampere meter fuse may be cut.
·Do not turn on the main switch while current is being
measured.
LEAK CURRENT : Not to exceed 1mA
BATTERY ADJUSTMENT VOLTAGE CHECK

● Connect the voltmeter between the battery terminals.
● Connect the amperemeter between the main fuse
termanals.
● Start the engine and measure the charging voltage and
ampere while incresae the rpm gradually.
CONTROL VOLTAGE (CHARGING SIDE) : 13.0~14.5 0.5V/5,000rpm

(LAMP SIDE) : 13.1~ 0.5V/5,000rpm
13-4
·Check with fully charge the battery which has the

voltage between terminal of 13.0~13.2V.
·In case that the engine is started by the starter motor,
measurement must be performed after accelating
(charging) for 10 seconds.
CHARGING CURRENT CHECK

● Check the charging current passed through the
generator assy, regulator comp is normal with the
discharged battery.
CHARGING CURRENT : 1.5~2.4A/5,000rpm

TOOL : DIGITAL CIRCUIT TESTER
BATTERY CHARGING
● Remove the battery from the frame, and connect it to
the battery charger.
-Connect the charger positive (+) cable to the battery
positive (+) terminal.
-Connect the charger negative (-) cable to the battery
negative (-) terminal.
·Do not connect the charger to the battery coupler

terminals.
● Never open the sealed filler cap.
·The battery generates hydrogen gas which can be

highly explosive. Do not smoke or allow flames or
sparks near the battery, easpecially while charging it.
·Turn power ON/OFF at the charger, not at the battery
terminals. If the cable is disconnected or connected at
the battery terminal during charging, spark may jump
and ignite the flammable gas.
·Always remove the battery from the frame when
charging it. If the battery is charged while installed in
the frame, the electrolyte may spill and corrode the
frame components.
CHARGING CURRENT : 0.3A

CHARGING TIME : 8~10h
·Do not let the electrolyte temperature rise above 45

℃(113℉). If the electrolyte temperature becomes
too high, lower the charging current.
·Quick-charging will shorten the battery life and
cause battery damage. It chould only be done in
emergency; slow-charging is prefered.
13-5
HEADLIGHT VOLTAGE INSPECTION

·Check voltage with the headlight coupler connected.
● After starting the engine, place the dimmer switch to

HI and check the voltage between the blue (+) and
green (-) wires of the headlight coupler.
·Measurement is performed in AC area.
CONTROL VOLTAGE : 12.6~13.6V/5,000rpm
● If voltage is incorrect, check the regulator/rectifier.
REGULATOR/RECTIFIER INSPECTION
HARNESS CIRCUIT INSPECTION
● Remove the front cover. ( 3-5 )
REGULATOR RECTIFIER COUPLER
● Remove the 4P coupler of the regulator/rectifier and
inspect the wiring circuit in the main harness side
terminal.
ITEM MEASUREMENT LOCATION LEVEL AREAS OF INSPECTION IF INCORRECT

BATTERY WIRE Voltage between red “⊕” and green “⊖”. There must be battery voltage. Damaged, disconnected main fuse/harness.
CHARGING ※ Resistance between white wire and 0.4~1.0Ω(20℃)
COIL earth wires. Disconnect the starter. AC generator (charging, lighting coil
※ Resistance between yellow wire and coupler connection damage) resister(6.7Ω
LIGHTING
earth wires. Disconnect dimmer 0.2~0.8Ω(20℃) 5W) headlight lighting circuit.
COIL
switch connection
Inspect ※ part after at least 10 minutes later.
REGULATOR/RECTIFIER INSPECTION
(BATEERY TERMINAL) (LAMP TERMINAL) ● If the inspection of the harness side proves to be
satisfactory, check the regulator/rectifier coupler for
TERMINAL ARRANGEMENT faulty connection, and measure the resistance between
the terminals of the regulator/rectifier.
RESISTANCE VALUE (20℃) Unit :

Tester ⊕
Tester ⊖ A L B E
A ∞ 3-50 ∞
L ∞ ∞ 5-100
B ∞ ∞ ∞
(CHARGING TERMINAL) (EARTH TERMINAL)
E ∞ 5-100 ∞
13-6
A.C. GENERATOR
REMOVE
● Engine hanger side RH. cover. ( 3-5 )
● Plug cap.
● Loosen the 3 washer screws, remove the fan cover and
the fan cover element A,B.
● Remove the fan cover rubber.
COOLING FAN
● Loosen the 2 flange bolts, remove the fan cover.
● Loosen the 4 cooling fan fixing flange bolts, remove
the cooling fan.
● Hold the flywheel with a universal holder.
● Remove the flywheel with a ACG rotor puller.
TOOL : ACG ROTOR PULLER 0750-00004
● Remove the connector/coupler on the wire harness or

starter motor. Remove the ground wires.
NUT
FLYWHEEL
● Loosen the 2 pulse generator fixing flange bolts,

remove the pulse generator.
● Loosen the 2 stator fixing flange bolts.
● Remove the grommet from the crankcase cover.
● Remove the stator.
·Insert the puller shaft and remove the flywheel after

inserting the ACG rotor puller and securing it with
spanner.
·The flywheel may easily removed if you rotate the
ACG ROTOR PULLER puller while tapping the roller shaft with metal
hammer.
·Always use a holder and a puller to remove the
flywheel. Do not try to remove the flywheel by
hammering directly on it. The crankshaft or
components could be damaged.
·Remove the woodruff key with care not to lose it.
13-7
STATOR INSTALLATION
● Note the direction of stator, and install the stator on the
crankcase.
INSTALL
● Grommet to R. crankcase cover.
● A.C. generator wire coupler to wire harness.
● Connector to starter motor, then install the ground wire.
STATOR COMP.
FLYWHEEL INSTALLATION
● Clean the tapered portion of the crankshaft.
● If the flywheel is installed with dust or dirt on the taper,
the taper will not make secure contact with the
flywheel and there will be excessive force on the
woodruff key.
● Insert the woodruff key into the key groove in the
crankshaft.
● Set the flywheel groove to the woodruff key and install
the flywheel on the crankshaft.
FLYWHEEL
● Tighten the flywheel bolt (or nut) with your fingers.
·Before installing the flywheel, check that no nuts or

bolts are magnetically attached to the flywheel.
Installing the flywheel with anything attached to it
could damage the stator coil.
● Hold the flywheel rotor with a holder and tighten the

bolt (nut) to the specified torque.
INSTALL
● Cooling fan.
● Fan cover.
● Fan cover rubber.
● Fan cover and the fan cover element A,B.
● Engine hanger side RH. ( 3-5 )
COOLING FAN
13-8
A.C. GENERATOR(CHARGING COIL)
INSPECTION
·This test is done with the starter mounted to the

engine.
ACG ● Remove the luggage box. ( 3-3 )

COUPLER ● Disconnect the AC generator coupler. ( 3-3 )
● Measure the resistance of the charging coil (between
the white wire and ground) and the lighting coil
(between the yellow wire and ground).
STANDARD RESISTANCE (20℃)

BETWEEN WHITE WIRE AND GROUND : 0.3~1.2Ω
BETWEEN YELLOW WIRE AND GROUND : 0.1~1.0Ω
RESISTER INSPECTION
● Measure the resistance between the register lead wire
and ground.
STANDARD VALUE (20℃)

RESISTER (6.7Ω 5W) GREEN/BLACK/BODY GROUND : 6.3~7.1Ω
RESISTER (5.9Ω 30W)PINK/BODY GROUND : 5.6~6.5Ω
·Problems with the resister are caused by operational

problems of the starter.
13-9
MEMO
14. IGNITION SYSTEM
SERVICE INFORMATION 14-1 EXCITE COIL INSPECTION 14-6

IGNITION DEVICES LOCATION 14-2 PULSE GENERATOR INSPECTION 14-6
TROUBLESHOOTING 14-3 IGNITION TIMING INSPECTION 14-7
IGNITION SYSTEM INSPECTION CDI UNIT 14-7
(PEAK VOLTAGE MEASUREMENT) 14-4 SIDE STAND IGNITION
IGNITION COIL 14-5 CUT-OFF SWITCH 14-8
SERVICE INFORMATION
GENERAL SAFETY
● Refer to the malfunction diagnosis when inspecting ignition devices.
● Because the ignition devices have installed electrical advancer devices, it is impossible to adjust ignition timing.
● Be careful when handling the ignition devices as they can become easily damaged if dropped or bumped. Also, do not
disconnect or connect the connectors and couplers when the main swtich is turned ON as excessive electric current can
cause damage in the unit. Always perform maintenance work on the ignition devices with the main switch turned OFF.
● Ignition devices can often appear to be malfuctioning when the couplers or connectors are disconnected. Check these
connections before working on.
● Use recommended spark plug. Using incorrect spark plug may make the engine run badly or damage the engine.
● This manual gives explanations on inspections to receive peak voltage. As inspections for coil resistance values are also
included, it may be difficult to make a correct determination.
● Conduct inspection on the main swtich by referring to the wiring diagram continuity chart. ( chapter 16 )
14
14-1
IGNITION SYSTEM
IGNITION DEVICES LOCATION
START SWITCH
RESISTOR
CDI UNIT

IG COIL
ACG. CORD COUPLER
A.C.GENERATOR
HIGH TENSION CORD
BLUE / YELLOW GREEN
BLACK / RED BLACK / YELLOW
BLACK / WHITE
CDI UNIT
PULSE GENERATOR
MAIN SWITCH
SIDE STAND IGNITION COIL

AC GENERATOR
SWITCH SPARK PLUG
14-2
IGNITION SYSTEM
TROUBLESHOOTING
Spark plug does not emit sparks.
ABNORMAL STATE POSSIBLE CAUSES (START FROM 1 AND GO THROUGH LIST IN ORDER)
1. Using a tester with a low internal resistance.

2. Cranking speed is low.
- Battery is low or kick power is weak.
3. Influence of tester sampling time (normal state if measured a
number of times and shows over the set voltage).
IGNITION COIL PRIMARY VOLTAGE
Maximum voltage is low.

4. Problem in ignition system wiring (disconnected, damaged).
5. Ignition coil is damaged.
6. Excite coil is damaged (measure peak voltage).
7. CDI unit is damaged (when no porblems in 1~6 and spark plug
does not emit sparks)
1. Adaptor is connected incorrectly.

2.Main switch damaged.
3. CDI unit coupler is connected incorrectly.
4. CDI unit ground wire disconnection.
No, or almost no peak voltage. 5. Damage to excite coil (measure peak voltage).
6. Pulse generator is damaged (measure peak voltage).
7. Peak voltage adaptor is damaged.
8. CDI unit is damaged (when no problems in 1~7 and no sparks
emitted from spark plug).
Spark plug peak voltage is normal but 1. Damage to spark plug or leakage of ignition coil secondary current.
spark plug does not emit sparks. 2. Damaged ignition coil.

2. Cranking speed is too low.
EXCITE COIL
- Battery is insufficiently charged or kick power is weak.

Peak voltage is low.
number of times and shows over the set voltage)
4. Excite coil is damaged (when 1~3 is okay).
1. Peak voltage adaptor is damaged.

No, or almost no peak voltage.
2. Excite coil is damaged.

PULSE GENERATOR
2. Cranking speed is too low.

- Battery is insufficiently charged or kick power is weak.
Maximum voltage is low.
number of times and shows over the set voltage).
4. Pulse generator is damaged (when 1~3 is okay).
1. Maximum voltage adaptor is damaged.

No, or almost no maximum voltage.
2. Pulse generator is damaged.
14-3
IGNITION SYSTEM
IGNITION SYSTEM INSPECTION

(PEAK VOLTAGE MEASUREMENT)
·When sparks are not emitted from spark plug, after

checking for disconnection in wires and looseness,
measure peak voltage for each wire.
● Connect the peak voltage adaptor to the digital tester.

DAELIM PVA MULTI TESTER
IGNITION COIL PRIMARY VOLTAGE
·Make sure each wire is correctly connected to ensure

correct measurement.
·Inspect when there is cylinder compression pressure
and with the spark plug cap securely connected to the
spark plug.
● Remove the luggage box. ( 3-3 )

● With the ignition coil wire connected, contact the peak
voltage adaptor to the initial wire adaptor terminal
(black/yellow) and ground (on vehicle body.). Turn the
main swtich ON, operate the starter motor, and
measure the ignition coil initial side peak voltage.
⊕”-BODY EARTH “⊖
CONTACT POINTS : BLACK/YELLOW TERMINAL “⊕ ⊖”
PEAK VOLTAGE : OVER 120V
·When measuring voltage, do not touch the metal part

of the handle rod as there is the danger of receiving
an electric shock.
EXCITE COIL
·Assemble the spark pug to the cylinder head, inspect

in a state having compression pressure.
REMOVE
● CDI unit. ( 14-7 )
● Coupler from the CDI unit contact the peak voltage
adaptor to the excite coil wire (black/red and green) of
the harness side coupler.
● Operate the starter motor and measure the excite coil
peak voltage.
⊕”-BODY EARTH “⊖
CONTACT POINTS : BLACK/RED TERMINAL “⊕ ⊖”
PEAK VOLTAGE : OVER 120V

of the handle rod as there is the danger of recieving
an electric shock.
14-4
IGNITION SYSTEM
PULSE GENERATOR
·Inspect with the spark plug assembled and while

there is compression pressure.
● Remove the CDI unit. ( 14-7 )

● Remove the coupler from the CDI unit and connect the
peak voltage adaptor to the pulse generator wire (blue/
yellow and green) of harness coupler.
● Operate the starter motor and measure the peak voltage
of the pulse generator coil.
⊕”-BODY EARTH“⊖
CONTACT POINTS : BLUE/YELLOW TERMINAL “⊕ ⊖”
PEAK VOLTAGE : OVER 1.5V

of the handle rod as there is the danger of receiving
an electric shock.
● Perform the following inspections if measured peak

voltage in the CDI unit coupler portion is abnormal.
● Disconnect the AC generator cord coupler and connect
the adaptor.
● In the same manner as with the unit coupler side,
measure peak voltage and compare with the first peak
voltage.
● When the measured value in the unit side is abnormal
and normal in the pulse generator side, the problem is
either incorrect coupler connection or disconnection of
the wire harness.
● When both measurements are abnormal, this indicates
a problem with the pulse generator. Refer to the
malfunction diagnosis are go through each step.
IGNITION COIL
IGNITION COIL REMOVE
● Plug maintenance cover.
● Spark plug cap.
● Loosen the ignition coil fixing bolt.
● Disconnect the ignition coil wire.
● Remove the ignition coil.
·Arrange the cords in the right place.
FIXING SCREW
14-5
IGNITION SYSTEM
INSPECTION (RESISTANCE MEASUREMENT)
● Measure primary coil resistance between the green and
black/yellow terminals.
STANDARD VALUE : 0.1~0.5Ω(20℃)
● Measure the secondary coil resistance between the plug

cap and green wire terminals.
RESISTANCE VALUE
(SPARK PLUG CAP CONNECTION) : 6.5~9.5㏀ (20℃)
● The coil which the resistance value indicate

“∞”(disconnection) remove the plugcap, and measure
the resistance of secondary coil.
● Measure the resistance between the high tension code
and green code terminals.
RESISTANCE VALUE : 2.6 1.25㏀ (20℃).
EXCITE COIL INSPECTION
·Assembly the spark plug to the cylinder head, and

inspect in an state having compression pressure.

● Remove the connection of the AC Generator wire
connector (black/red), measure the resistance between
the terminal of AC generator and body earth.
STANDARD VALUE : 500Ω 20 (20℃)
PULSE GENERATOR INSPECTION
·The inspection of pulse generator is performed in a

state assembling to the engine.

● Remove the connection of the AC generator 6P
coupler, and measure the resistance between the blue/
yellow of starter and green code.
STANDARD VALUE : 100Ω 20 (20℃)
14-6
IGNITION SYSTEM
IGNITION TIMING INSPECTION

TIMING LIGHT
·As a CDI device is used in this vehicle, there is no

need for adjusting ignition timing. If ignition timing
problems occur, inspect the CDI unit and the AC
generator and replace if any malfunctions are found
in the devices.
·Ignition timing inspection well read the instruction
manual of timing light or revolution-indicator, and
handle it exactly.
● Warm up the engine.

● Remove the center cover.
● Remove the floor panel.
● Remove the fan cover.
● Connect timing light to the high-tension cord.
● When engine rpms are at 1,800, ignition timing is
correct if the “F” mark and crank case index mark are
aligned.
IGNITION TIMING : 17 DEGREES 2 BTDC/1,800 rpms
·Index mark must face the spark plug.
CDI UNIT
CDI
CDI UNIT
CDI UNIT
UNIT ● Remove the luggage box. ( 3-3 )
● Disconnect the coupler from the CDI unit and remove
STARTER
STARTER RELAY
STARTER RELAY
RELAY CDI Unit.
IGNITION
IGNITION COIL
IGNITION COIL
COIL
CIRCUIT INSPECTION
● Remove the coupler from the CDI unit, and check the
ignition system circuits from the wiring coupler side.
INSPECTION ITEM CHECK POINT STANDARD VALUE
PULSE GENERATOR BLUE/YELLOW AND GREEN 100Ω±20%(20℃)
IGNITION COIL
-PRIMARYCOIL BLACK/YELLOW AND GREEN 0.1~0.5Ω(20℃)
-SECONDARY COIL GREEN AND HIGH-TENSION CORD
(ATTACH THE PLUG CAP) 6.5~9.5KΩ(20℃)
(DETACH THE PLUG-CAP) 2.6±1.25KΩ(20℃)
TESTING BY CDI TESTER

● Check the CDI unit spark performance by using a CDI
tester.
·Read tester manual carefully prior to using the tester.
14-7
MEMO
15. STARTING SYSTEM
SERVICE INFORMATION 15-1 STARTER MOTOR 15-4

STARTING DEVICES LOCATION 15-2 STARTER RELAY INSPECTION 15-7
TROUBLESHOOTING 15-3 STARTER PINION GEAR INSPECTION 15-7
SERVICE INFORMATION
GENERAL SAFETY
·When performing maintenance on the starter motor and related parts, turn the main switch to OFF. There is the
danger of the starter motor unexpectedly operating if the main switch is not turned to OFF.
● First check connection with battery and battery charge level before beginning maintenance on the starter motor.
● It is possible for the starter motor coil to become damaged if the starter is operated when the engine does not turn over.
15
15-1
STARTING SYSTEM
STARTING DEVICES LOCATION
START SWITCH
RESISTOR
CDI UNIT

IG COIL
ACG. CORD COUPLER
A.C.GENERATOR
HIGH TENSION CORD
RED MAIN SWITCH

RED/WHITE
FUSE
REAR STOP SWITCH

STARTER STARTER
MOTOR SWITCH
GREEN
BLACK
GREEN
BATTERY
STARTER
RELAY GREEN/YELLOW
FRONT STOP
SWITCH
YELLOW/RED GREEN/YELLOW
15-2
STARTING SYSTEM
TROUBLESHOOTING
Starter motor does not rotate (No response from starter motor).
● Check to see if the fuse is burned out.
With the main switch turned to ON, squeeze Remove the starter motor “⊕” wire, connect
the brake lever. In this state push the starter it to the battery “⊕” terminal and check to
button and check if a clicking noise then an CLICKS see if the starter motor rotates (because a
operating noise is emitted from the starter large amount of current flows in this test, do
relay. not use thin wire).
DOES NOT ROTATE

NO CLICK. ROTATES
● Incorrect starter motor
connection
● Incorrect wise or coupler connection.

Remove the coupler from the starter replay
NO CONTINUITY. ● Incorrect connection with the switch
and inspect the relay coil ground wire.
terminals or harness disconnection.
CONTINUITY.
Check the starter relay voltage in the starter

NO VOLTAGE. ● Damaged main or starter switch.
relay coupler with the coupler connected.
● Incorrect connection with coupler connector.
VOLTAGE MEASURED.
● Disconnection in starter switch wire.
Check the operation of the starter relay. NORMAL ● Loose or poor contact at starter relay switch
connector.
ABNORMAL ● Faulty starter relay switch.
Weak rotational power in starter motor (Does not turn over engine).
● Battery is insufficiently charged.
● Incorrect connection of battery terminal cord.
● Damaged starter motor.
● Ground wire is connected incorrectly
● Brush is damaged or worn.
Starter motor if free-wheeling

● Motor terminals are connected backwards.
● Starter pinion is damaged or operating incorrectely.
Starter motor is normal but does not turn engine over.

● Engine is malfunctioning so the crank shaft is not rotating.
● Incorrect meshing of gears in starter pinion.
15-3
STARTING SYSTEM
STARTER MOTOR
REMOVE
STARTER MOTOR ● Center cover. ( 3-3 )
● Floor side RH. cover. ( 3-4 )
● Engine hanger side cover RH. ( 3-5 )
● Disconnect the starter wire connector, remove the wire
from the wire fixing clamp.
● Loosen the 2 starter motor fixing bolts.
● Remove the starter motor.
FIXING BOLT
STARTER MOTOR ·Accurately tighten the earth wire.

·Turn off the main switch prior to servicing the starter
motor. If power is connected, the starter motor may
be activated and damaged.
DISASSEMBLY
● Remove the starter motor screws and remove the motor
cover.
WASHER SCREW
·Record the order so the parts can be installed
correctly later.
INSPECTION
BRUSH ● Check for continuity of the starter motor case.
-Between cord terminal“⊕” and bracket“⊖”: normal
FRONT if no continuity.
BRACKET -Between cord terminal and brush (black wire) :
normal if there is continuity.
● If abnormal, replace with a new one.
● Measure the brush length. Replace the brush if it is

worn beyond the service limit.
SERVICE LIMIT : 3mm

BRUSH
15-4
STARTING SYSTEM
● Check the commutator for :
-Damage or abnormal wear. → Replace with a new
one.
-Discoloration of the commutator bar. → Replace with
a new one.
-Metallic debris between commutator bars.→ Clean it
off.
COMMUTATOR
● Check for continuity between pairs of commutator

bars.
COMMUTATOR BARS ● Make a continuity check between individual
commutator bars and the armature shaft.
● There should be no continuity.
● Check the bearings.

-Do not rotate smoothly. → Replace with a new one.
-Loose bearing. → Replace with a new one.
BEARING
STARTER MOTOR ASSEMBLY

● Carefully insert the armature shaft into the front
bracket.
● Align the front bracket notch with the brush.
·The sliding surcfaces of the brushes can be damaged

if they are not installed properly.
FRONT BRACKET
15-5
STARTING SYSTEM
● Insert the brush spring into the brush holder and install
the front bracket.
·Insert the brush spring with care so that it does not

lean in the holder.
BRUSH HOLDER
● Apply grease to both ends of the armature shaft.
GREASE
● Install the starter motor cover.
·The coil may be damaged if the magnet pulls the

armature against the case.
STARTER MOTOR COVER
● Align the front bracket with the cover.

● Tighten the washer screw.
WASHER SCREW
15-6
STARTING SYSTEM
STARTER RELAY INSPECTION

● When battery voltage is applied between the starter
relay green/yellow wire and yellow/red terminals, there
should be continuity between the red and red/white
terminals. The terminals are distinguished by the
corresponding wire color of the wire harness connector.
STARTER PINION GEAR INSPECTION

REMOVE
● L. side cover. ( 7-2 )
● Drive face. ( 7-6 )
● Starter pinion gear.
INSPECTION
● Wear or damage to the pinion, reduction gears.
→ Replace with a new one.
● Worn journals.→ Replace with a new one.
● Check if the pinion gear moves smoothly along the

axis.
● Pinion gear does not move smoothly. → Replace with
a new one.
15-7
MEMO
16. LIGHTS/METER/SWITCHES
SERVICE INFORMATION 16-1 HANDLE SWITCH INSPECTION 16-4

TROUBLESHOOTING 16-1 FRONT STOP SWITCH INSPECTION 16-4
FUEL UNIT 16-2 BULBS REPLACEMENT 16-5
OIL LEVEL SWITCH 16-3 METER REPLACEMENT 16-7
MAIN SWITCH 16-3 HORN INSPECTION 16-7
SERVICE INFORMATION
GENERAL SAFETY
● Refer to tester owner’s manuals when performing continuity inspections.
● Refer to wiring diagram (chapter 17) for switch continuity.
● After inspecting and/or performing maintenance work make sure the wires and cables are properly placed and
connected.
TROUBLESHOOTING
Fuel meter indicator malfunctioning Oil indicator light not operating
● Coupler separated. (when there is oil).
● Harness disconnected. ● Burned out fuse.
● Float operation malfuction. ● Battery insufficiently charged.
● Fuel unit damaged. ● Main swtich damaged.
● Meter damaged. ● Meter damaged.
● Oil level switch damaged.
Fuel meter needle unstable ● Loose connector.
● Coupler loose. ● Harness disconnection.
● Fuel unit damaged.
● Meter damaged. Oil indicator does not turn off (when oil is out)
● Oil level switch damaged.
Headlight hi-lo not operating ● Green/red wire joined.
● Bulb malfunction.
● Dimmer switch damaged.
16
16-1
LIGHTS/METER/SWITCHES
FUEL UNIT
REMOVAL
● Remove the fuel unit wire from the wire harness.
● Turn the fuel unit fixing unit set cap comp to the left,
and remove it.
● Remove the fuel unit from the fuel tank.
·Be careful of prevention the fuel unit wire from

damaging.
·When disassembling, be careful of prevention the
float arm from damaging.
● Remove the base packing.
·Check for damage.
FUEL
FUEL UNIT
FUEL UNIT
FUEL UNIT
UNIT
FUEL
FUEL
FUEL UNIT
UNIT
UNIT SET
SET
SET CAP
CAP
CAP
INSTALLATION
● Install the base packing to the fuel tank.
● Install the fuel unit.
·Install it aligning the part of the fuel unit with the

loop part of fuel tank.
·Check the fuel leakage.
16-2
OIL LEVEL SWITCH

REMOVE
● Oil level switch wire.
● Oil level switch from the oil tank.
● Install in the reverse order of remeval.
OIL LEVEL
SWITCH ·Disassemble after adjusting the oil level.
INSPECTION
● Move the float to farthest extreme up and down and
check the continuity of the terminals.
● It’s normal state if there is no continuity when the float
is up, but continuity when it is down.
MAIN SWITCH
REMOVAL/ INSTALLATION
● Remove the inner box. ( 3-5 )
● Disconnect the main switch coupler.
MAIN ● Remove the seat lock cable.
SWITCH ● Loosen the 2 screws and remove the main switch.
INSPECTION
● Inspect continuity of each terminal.
TERMINAL IG E BA1 BA2

ON
OFF
LOCK
COLOR BLACK/WHITE GREEN RED BLACK
16-3
HANDLE SWITCH INSPECTION

REMOVE
● Front handle cover. ( 3-6 )
● Handle switch coupler, connector, inspect continuity of
each terminal.
● If abnormal, inspect the switch.
STARTER SWITCH LIGHTING SWITCH

LIGHTING
LIGHTING
LIGHTING SWITCH
SWITCH
SWITCH
ST E HL C1 TL RE
FREE OFF
PUSH (N)
COLOR YELLOW/RED GREEN PO
(N)
H
BROWN
COLOR / WHITE BROWN YELLOW PINK
STARTER
STARTER
STARTER SWITCH
SWITCH
SWITCH WINKER SWITCH DIMMER SWITCH
R L WR HI LO HL
L LO
N N
R HI
COLOR SKY BLUE ORANGE GRAY COLOR BROWN WHITE BLUE
DIMMER
DIMMER SWITCH
DIMMER SWITCH
SWITCH HORN SWITCH
HO BAT
FREE
HORN
HORN
HORN SWITCH
SWITCH
SWITCH PUSH
WINKER
WINKER
WINKER SWITCH
SWITCH
SWITCH
COLOR LIGHT GREEN BLACK
FRONT STOP SWITCH INSPECTION

● Remove the black wire and green/yellow wire
terminals inside the speedometer assembly, and check
the following.
-When the brake lever is pulled - continuity.
-When the brake lever is released - no continuity.
FRONT STOP SWITCH
16-4
HEADLIGHT
HEADLIGHT
HEADLIGHT RUBBER
RUBBER
RUBBER COVER
COVER
COVER BULBS REPLACEMENT
HEADLIGHT BULB
● Remove the headlight rubber cover.
● Push down on the socket and turn to the left.
● Replace with new bulb.
WINKER
WINKER
WINKER RELAY
RELAY
RELAY
·Before replacing the bulb, be sure to check the
swtiches for loose connection of the connectors.
HEADLIGHT
HEADLIGHT
HEADLIGHT BULB
BULB
BULB
·Headlight bulbs become very hot while the headlight

is ON, and remain hot for a while after they are
turned OFF.
·Be sure to turn the ignition switch OFF and let the
bulb cool down before replacement.
·If you touch the bulb with your bare hands, clean it
with a cloth moistened with denatured alcohol to
prevent early bulb failure.
·Be sure to install the dust cover after replacing the
bulb.
FRONT WINKER BULB

FRONT
FRONT
FRONT WINKER
WINKER
WINKER
● Remove the bulb from the socket, replace with new bulb.
16-5
REAR WINKER BULB REPLACEMENT
TAILLIGHT BULB
TAILLIGHT
TAILLIGHT BULB
BULB
● Press the winker lens groove and open the winker lens
using plain screwdriver.
● Remove the bulb from the socket, replace with new bulb.
·Pay attention not to damage the lens.

·Do not apply excessive force when removing the
lens.
REAR
REAR WINKER
REAR WINKER
WINKER
TAILLIGHT BULB REPLACEMENT

● Loosen the 2 pan screws, remove the tail light lens.
● Replace the tail stop light bulb with the new one.
·Pay attention not to damage the tail light lens when

removing it.
SCREW
SCREW
SCREW
BULB
BULB
BULB
METER BULB REPLACEMENT
BULB
● Remove the bulb socket, replace with new bulb.
SPEEDOMETER
SPEEDOMETER
SPEEDOMETER
SPEEDOMETER
METERS REPLACEMENT
● Remove the front/rear stop swtich wire.
● Remove the speedometer cable from the meter.
● Loosen the 4 steering handle tapping screws.
● Remove the speedometer coupler connected to the wire
harness
● Remove the speedometer wiring from the steering
handle cable guide.
● Remove the speedometer and the gear handle cover
assemblied from the steering handle.
16-6
● Roose the 3 tapping screws securing the speedometer
FLANGE
FLANGE BOLT
FLANGE BOLT
FLANGE BOLT
BOLT and the rear handle cover.
● Disconnect the R/L wiring.
● Remove the speedometer assembly.
·Check the each switch for proper operation.

·The wire and cable must be connected accurately.
SPEEDOMETER
SPEEDOMETER
SPEEDOMETER CABLE
CABLE
CABLE
HORN INSPECTION
● Remove the horn wiring, and connect a fully charged
12V battery. Check the sound quality for any
abnormalities.
HORN
16-7
MEMO
17. WIRING DIAGRAM
17
17-1
MEMO
18. TROUBLESHOOTING
ENGINE DOES NOT START OR IS HARD TO START 18-1

ENGINE OUTPUT INSUFFICIENT 18-2
POOR PERFORMANCE AT LOW SPEED AND IDLING 18-3
POOR PERFORMANCE AT HIGH SPEED 18-3
UNSATISFACTORY OPERATION 18-4
FUEL GAUGE 18-6
STARTER MOTOR 18-7
ENGINE DOES NOT START OR IS HARD TO START

CAUSE OF TROUBLE
1. Open the drain screw, and check fuel Fuel not supplied (1)Fuel tank empty.
flow to the carburetor. to the carburetor. (2)Fuel tube up to the fuel tank
Fuel is supplied.
clogged, or the vacuum tube or fuel
tube up to the inlet pipe clogged.
(3)Float valve clogged.
(4)Fuel tank cap air hole clogged.
(5)Fuel supply pipe frozen.
(6)Fuel strainer clogged.
2. Check spark plugs. Weak or no spark. (1)Faulty spark plug.

(2)Contaminated spark plug.
Good spark (3)Faulty CDI unit.
(4)Faulty A.C. generator.
(5)Disconnected or shorted high
tension cord.
(6)Disconnected or shorted ignition
coil.
(7)Faulty main switch.
3. Test cylinder pressure. Low cylinder pressure. (1)Piston ring seized.

Pressure normal (2)Cylinder and piston ring won.
(3)Cylinder and cylinder head cracked.
(4)Crank case air leaks.
(5)Cylinder head gasket damaged.
4. Start engine in the following Engine starts but (1)Manifold air leaks.
procedure. stops immediately. (2)Inadequate ignition timing.
Engine will not start.
18
5. Remove spark plugs. Plugs wet. (1)Carburetor flooded.
(2)Faulty control box.
Dry plugs
(3)Throttle valve excessively opened.
18-1
TROUBLESHOOTING
ENGINE OUTPUT INSUFFICIENT
CAUSE OF TROUBLE
1. Gently accelerate engine. Engine speed does not (1) Air cleaner clogged.
Engine speed increases. increase sufficiently. (2) Insufficient fuel supply.
(3) Fuel tank cap air hole clogged.
(4) Muffler clogged.
2. Check ignition timing. Abnormal (1) Faulty CDI unit.

Normal (2) Faulty A.C generator.
3. Press the kick starter pedal to check Low (1) Cylinder and piston ring worn.
the cylinder pressure. (2) Cylinder head gasket damaged.
Normal (3) Cylinder and cylinder head cracked.
4. Check the carburetor for clogging. Clogged. (1) Unsatisfactory carburetor

Not clogged. maintenance.
5. Remove spark plugs. Contaminated or (1) Unsatisfactory plug maintenance.

Not contaminated or discolored. discolored. (2) Plugs with incorrect heat value
used.
(3) Rich fuel mixture.
6. Check for engine overheating. Overheated. (1) Cylinder or piston worn.

Not overheated. (2) Lean fuel mixture.
(3) Poor quality fuel used.
(4) Carbon deposit inside the
combustion chamber excessive.
(5) Ignition timing incorrect.
7. Accelerate suddenly or run at. Engine knocks. (1) Carbon deposit inside the
Engine does not knock. combustion chamber excessive.
(2) Poor quality fuel used.
(3) Lean fuel mixture.
18-2
TROUBLESHOOTING
POOR PERFORMANCE AT LOW SPEED AND IDLING
CAUSE OF TROUBLE
1. Check ignition timing. Abnormal (1) Faulty CDI unit.
Normal
2. Check the carburetor air screw. Incorrect (1) Excessive fuel mixture.
Correct (Loosen screw to correct
adjustment level.)
(2) Lean fuel mixture.
(Tighten screw to correct
adjustment level.)
3. Check the area around the manifold Leaking (1) Faulty insulator packing.
for air leakage. (2) Loose carburetor.
No leak. (3) Faulty inlet pipe packing.
(4) Faulty insulator O-ring.
Weak or intermittent (1) Carbon deposited on spark plugs or

4. Check sparks. sparks. spark plugs contaminated.
Sparks normal. (2) Faulty CDI unit.
(3) Faulty ignition coil.
(4) Faulty A.C. generator.
(5) Faulty main switch.
POOR PERFORMANCE AT HIGH SPEED
CAUSE OF TROUBLE
1. Check ignition timing. Incorrect (1) Faulty CDI unit.
Correct (2) Faulty A.C. generator.
2. Remove the fuel tube from the fuel Insufficient fuel supply. (1) Fuel tank empty.
valve. (2) Fuel tube or fuel filter clogged.
Fuel flows. (3)Fuel tank cap air hole clogged.
3. Remove the carburetor, and check Clogged. (1) Clean.

for clogged jets.
Not clogged.
18-3
TROUBLESHOOTING
UNSATISFACTORY OPERATION
CLUTCH DRIVE/DRIVEN PULLEY CAUSE OF TROUBLE

1. Engine starts but motorcycle does not move. (1) Drive belt worn or slips.
(2) Ramp plate damaged.
(3) Drive face spring damaged.
(4) Clutch lining came off.
(5) Driven pulley shaft spline damaged.
(6) Faulty transmission.
(7) Transmission seized.
2. Vehicle moves slow, engine starts but stops (1) Shoe spring damaged.
immediately. (2) Clutch outer and weight seized.
(3) Pivot seized.
3. Engine weak at start. (1) Drive belt worn or slips.

(2) Weight roller worn.
(3) Drive pulley bearing seized.
(4) Weak drive face spring.
(5) Drive pulley bearing worn or seized.
4. Engine weak at high speed. (1) Drive belt worn or slips.

(2) Weight roller worn.
(3) Drive pulley bearing worn.
5. Abnormal noise or odor. (1) Oil or grease spilled on the drive belt and inside pulley.
(2) Drive belt worn.
(3) Weak drive face spring.
(4) Driven pulley bearing worn or seized.
POOR MECHANICAL PERFORMANCE Check tire pressure.
CAUSE OF TROUBLE
1. Steering is heavy. (1) Steering head adjuster excessively tightened.
(2) Steering cone race or steel ball damaged.
2. Wheels wobbling. (1) Excessive wheel bearing play.

(2) Rim bent.
(3) Axle nut loose.
3. Motorcycle pulls to one side. (1) Front wheel and rear wheel not aligned.
(2) Front fork bent.
18-4
TROUBLESHOOTING
POOR FRONT/REAR SUSPENSION PERFORMANCE Check tire pressure.
CAUSE OF TROUBLE
1. Suspension excessively soft. (1) Cushion spring weak.
(2) Overloaded.
(3) Damper oil leaks.
2. Suspension excessively hard. (1) Fork pipe or cushion rod bent.
3. Noise from the suspension. (1) Sliders stuck.

(2) Cushion stopper rubber damaged.
POOR BRAKE PERFORMANCE Check brake adjustment.
CAUSE OF TROUBLE
1. If the arrow were mark and the brake (1) Brake shoe worn.
panel mark match with each other. (2) Brake cam worn.
(3) Shoe and cam contact surface worn.
(4) Brake drum worn.
2. Brake noise. (1) Brake shoe worn.

(2) Foreign matter in the brake lining.
(3) Brake drum and shoe contact surface curved.
3. Poor braking. (1) Brake wire defective or expanded.

(2) Only part of the brake shoe makes contact with the
brake drum.
(3) Clay or moisture inside the brake drum.
(4) Brake lining contaminated by grease or oil.
18-5
TROUBLESHOOTING
FUEL GAUGE
GAUGE READING INACCURATE (IGNITION SWTICH ON) CAUSE OF TROUBLE

1. Operate the turn signal to check the Signal continuously (1) Fuse cut.
battery circuit. operates dim or does not (2) Battery weak or totally discharged.
Signal operates satisfactorily. operate at all. (3) Faulty ignition swtich.
(4) Faulty terminal connection.
(5) Wire harness damaged.
2. Remove the fuel level sensor, and Needle moves. (1) Faulty float.
move float to check the status of
operation.
Float up : Full position
Float down : Empty position
Needle not moving.
3. Short-circuit the tank unit terminal Needle not moving. (1) Balance coil damaged or shorted.
on the wire harness side.
Needle not moving.
4. Terminal joints loose or faulty Unsatisfactory (1) Terminal loose.

connection. (2) Faulty terminal connection.
Check (1) Balance coil/lead shorted or

damaged.
GAUGE NEEDLE SHAKES OR VERTICALLY WOBBLES. CAUSE OF TROUBLE

(IGNITION SWTICH ON)
1. Operate the turn signal to check the Signal continuously (1) Fuse cut.
battery circuit. operates dim or does not (2) Battery weak or totally discharged.
Signal operates satisfactorily. operate at all. (3) Ignition switch damaged or shorted.
(4) Terminal loose of faulty connection.
2. Remove the tank and operate the Needle not moving. (1) Faulty fuel level sensor connection.
float.
Needle moving.
3. Move the float rapidly. One up/down Needle not moving. (1) Damper oil inside the meter
motion per second. insufficient.
Needle moving.
4. Start the engine, and measure the Resistance changed (1) Faulty connection between the
fuel level sensor resistance. significantly. sliding arm and the resistance.
Resistance not changed.
5. Check each joint. Unsatisfactory (1) Terminal connection loose or faulty

connection.
Satisfactory (1) Balance coil/lead shorted or

damaged.
18-6
TROUBLESHOOTING
STARTER MOTOR
STARTING MOTOR WILL NOT TURN CAUSE OF TROUBLE

1. Apply the brake and check the brake Light not activated. (1) Fuse cut.
stop light for operation. (2) Battery weak or totally discharged.
Light is activated.
(3) Faulty stop switch.
(4) Faulty terminal connection.
(5) Ignition swtich damaged or shorted.
2. Operate the turn signal to check the Signal continuously (1) Battery totally discharged.
battery circuit. operates dim or does not
operate at all.
Signal operates satisfactorily.
(60~120 signaling/second)
3. Press the starter switch to check the Unsatisfactory (1) Faulty starter switch connection.
starter magnetic. (2) Starter magnetic damaged or
Satisfactory shorted.
(3) Connector and terminals loose.
4. Connect the starter to battery and Starter does not turn. (1) Worn brush worn.
check operation. Light not activated. (2) Faulty connection between the rotor
Starter turns. and brush.
(3) Faulty the starter motor subwire
connection.
(4) Terminal loose.
STARTER MOTOR TURNS SLOW OR FAILS TO CRANK MOTOR CAUSE OF TROUBLE

1. Operate the turn signal to check the Signal continuously (1) Battery totally discharged.
battery circuit. operates dim or does not
Signal operates satisfactorily. operate at all.
2. Connect the starter subwire to the Operates sitisfactory. (1) Connector/terminal loose.
battery. (2) Faulty starter relay connector.
Turns slowly.
(with speed not changing)
3. Operate the kick starter. Operates heavy. (1) Engine seized.

Operates light. (1) Faulty connection between the rotor
and brush.
STARTER ROTATE WITHOUT STOPPING CAUSE OF TROUBLE

1. Turn off the ignition switch. (1) Pinion seized.
Will not stop
Starter relay connection seized.
18-7
MEMO
SERVICE MANUAL
2005. 6. PRINTED
2005. 6. PUBLICATION NO COPY
HEAD OFFICE (FACTORY)
#58, SUNG SAN-DONG, CHANGWON, KYUNGNAM, KOREA
TEL : (82-55) 239-7000 / FAX : (82-55) 239-7524
OVERSEAS SALES OFFICE
#13-5, SUNG SOO 1DONG 1GA, SUNG DONG GU, SEOUL, KOREA
TEL : (82-2) 498-6465 / FAX : (82-2) 467-9997
SM52-0506-01E

Daelim A-Four

Uploaded by

Copyright:

Available Formats

Daelim A-Four

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daelim A-Four

Uploaded by

Copyright:

Available Formats

HOW TO USE THIS MANUAL CONTENTS

This manual describes effective maintenance procedure for

GENERAL SAFETY 1-1 TWIST TORQUE 1-14

CAUTION WHEN WIRING

•Recheck the condition of contact, securing and

•Insert the lock of the coupler until the lock is fully

SERIAL NUMBER LOCATION

ENGINE SERIAL NUMBER LOCATION FRAME SERIAL NUMBER LOCATION

OVERALL LENGTH 1,798mm BRAKING DISTANCE 8.0m(30km/h VELOCITY)

OVERALL WIDTH 683mm MIN. REVOLUTION RADIUS 1,800mm

OVERALL HEIGHT 1,107mm COOLING TYPE AIR-COOLED

WHEEL BASE 1,260mm STARTING STARTER MOTOR, KICK

MOTOR TYPE SJ50R MOTOR TYPE 2-CYCLE

DISPLACEMENT 49.5cc NO. OF CYLINDERS, MOUNTING 1 CYLINDER, TRANSVERSE

FRONT AXLE 34kg BORE & STROKE 39.0X41.4mm

DRY WEIGHT REAR AXLE 58kg COMPRESSION RATIO 6.8:1

TOTAL 92kg MAX. OUTPUT 5.1PS/7,000rpm

PASSENGERS 2(65kg) MAX. TORQUE 0.42kgf·m/7,500rpm

FRONT AXLE 58.5kg PRIMARY SPEED REDUCTION RATIO 4.083

TOTAL 159kg TRANSMISSION GEARLESS TRANSMISSION

GROUND CLEARANCE 115mm

LUBRICATION TYPE Separation Lubrication

ITEM STANDARD USE LIMITS

CYLINDER HEAD, CYLINDER, PISTON

CYLINDER ID MARK LOCATION Side of Cylinder

INSIDE DIAMETER ID MARK(A) 39.000-39.005mm 39.05mm

PISTON OUTSIDE DIAMETER MEASUREMENT LOCATION

PISTON RING GAP TOP 0.10-0.25mm 0.40mm

CONNECTING ROD SMALL END PORTION DIAMETER 17.005-17.017mm 17.03mm

ITEM STANDARD USE LIMITS

DRIVE BELT WIDTH 17.5mm 16.5mm

DRIVEN PULLEY FACE SPRING FREE LENGTH 98.1mm 92.8mm

CRANK SHAFT LARGE END SIDE CLEARANCE 0.15~0.55mm 0.60mm

FRONT, REAR WHEELS

ITEM STANDARD USE LIMITS

SPARK PLUG STANDARD BR8HSA

CHARGING SYSTEM, AC GENERATOR

LIGHTS, METER, SWITCHES

LIGHTS, BULBS HEADLIGHT 12V-35/35W

TWIST PART NUMBER SCREW DIAMETER (mm) TWIST TORQUE REFERENCE

TOOL NAME TOOL NO. USAGE CHAPTER

HANDLE GRIP INSIDE AXLE PART Adhesives ROYAL BOND 1300

SYMBOL CAUTION SYMBOL CAUTION

Indicates needed application of silicon grease.

Indicates needed application of an antilock substance.

Indicates needed application of a sealant.

Indicates new part needed every time when disassembled.

Use recommended cushion oil.

Use Specialized Tool.

LIGHTING SW. CORD

30 WINKER SW. CORD PILOT BOX CORD

REGULATE RECTIFIER RESISTOR

RESISTOR CORD FR. BRAKE HOSE

WINKER REALY, ASS’Y

WIRE HARNESS COUPLER

HEAD LIGHT REAR WIRING DETAIL

SECODARY AIR FILTER ASS’Y

HIGH TENSION CORD