CH21-BatteryCharging 05-up-TRX450R-ER-21
CH21-BatteryCharging 05-up-TRX450R-ER-21
CH21-BatteryCharging 05-up-TRX450R-ER-21
21-1
BATTERY/CHARGING SYSTEM (After '05)
COMPONENT LOCATION
REGULATOR/ IGNITION SWITCH
RECTIFIER
FUSE(15A)(TRX450ER)
Bl:BLACK
R :RED
G :GREEN
Y : YELLOW
WPC G r : GRAY
5P Gr
EC CD
REGULATOR / RECTIFIER
ALTERNATOR e
BATTERY
12V 6AH
21-2
BATTERY/CHARGING SYSTEM (After '05)
SERVICE INFORMATION
GENERAL
ikWARNING
• The battery gives off explosive gases; keep sparks, flames and cigarettes away. Provide adequate ventilation when
charging.
• The battery contains sulfuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear protective
clothing and a face shield.
- If electrolyte gets on your skin, flush with water.
- If electrolyte gets in your eyes, flush with water for at least 15 minutes and call a physician immediately.
• Electrolyte is poisonous.
- If swallowed, drink large quantities of water or milk and call your local Poison Control Center or a physician
immediately.
• Always turn the ignition switch to OFF before disconnecting any electrical component.
• Some electrical components may be damaged if terminals or connectors are connected or disconnected while the igni-
tion switch is turned to ON and current is present.
• For extended storage, remove the battery, give it a full charge, and store it in a cool, dry space.
• For a battery remaining in a stored vehicle, disconnect the negative battery cable from the battery terminal.
• The battery sealing caps should not be removed. Attempting to remove the sealing caps from the cells may damage the
battery.
• The maintenance free (MF) battery must be replaced when it reaches the end of its service life.
• The battery can be damaged if overcharged or undercharged, or if left to discharge for long period. These same condi-
tions contribute to shortening the "life span" of the battery. Even under normal use, the performance of the battery
deteriorates after 2 - 3 years.
• Battery voltage may recover after battery charging, but under heavy load, the battery voltage will drop quickly and
eventually die out. For this reason, the charging system is often suspected as the problem. Battery overcharge often
results from problems in the battery itself, which may appear to be an overcharging symptom. If one of the battery cells
is shorted and battery voltage does not increase, the regulator/rectifier supplies excess voltage to the battery. Under
these conditions, the electrolyte level goes down quickly.
• Before troubleshooting the charging system, check for proper use and maintenance of the battery. Check if the battery
is frequently under heavy load, such as having the headlight and taiflight on for long periods of time without riding the
vehicle.
• The battery will self-discharge when the vehicle is not in use. For this reason, charge the battery every 2 weeks to pre-
vent sulfation from occurring.
• Filling a new battery with electrolyte will produce some voltage, but in order to achieve its maximum performance,
always charge the battery. Also, the battery life is lengthened when it is initially charged.
• When checking the charging system, always follow the steps in the troubleshooting (page 21-5).
• For alternator removal/installation, see (page 21-12)
BATTERY CHARGING
• Turn power ON/OFF at the charger, not at the battery terminal.
• For battery charging, do not exceed the charging current and time specified on the battery. Using excessive current or
extending the charging time may damage the battery.
• Quick charging should only be done in an emergency; slow charging is preferred.
BATTERY TESTING
Refer to the instructions in the Operation Manual for the recommended battery tester for details about battery testing. The
recommended battery tester puts a "load" on the battery so that the actual battery condition can be measured.
Recommended battery tester: BM-210-AH (U.S.A. only), BM-210, BATTERY MATE (MTP08-0192, U.S.A. only) or equivalent
21-3
BATTERY/CHARGING SYSTEM (After '05)
SPECIFICATIONS
ITEM SPECIFICATIONS
Battery Capacity 12V-6 Ah
Voltage Fully charged 13.0-13.2 V
(20°C/68°F) Needs
Below 12.3 V
charging
Charging current Normal 0.6 A/5-10 h
Quick 3.0 A/1 h
Current leakage 0.01 mA max.
Alternator Capacity 200 W/5,000 rpm (min1)
Charging coil resistance (20°C/68°F) 0 . 1 - 1.0 Q.
TORQUE VALUES
Alternator stator bolt 9.8N-m(1.0kgfm, 7 Ibf-ft)
Ignition pulse generator bolt 5 N-m (0.5 kgf-m, 3.6 Ibf-ft)
Flywheel nut 64 N-m (6.5 kgf-m, 4.7 Ibf-ft)
TOOLS
Battery tester Christie battery charger Battery Mate tester/charger
BM-210-AH (U.S.A. only) MC1012/2 (U.S.A. only) MTP08-0192 (U.S.A only)
21-4
BATTERY/CHARGING SYSTEM (After '05)
TROUBLESHOOTING
Battery is Damaged or Weak
1. Battery Test
Remove the battery (page 21-6).
Check the battery condition using the recommended battery tester.
RECOMMENDED BATTERY TESTER: BM-210-AH (U.S.A. only), BM-210, BATTERY MATE (MTP08-0192,
U.S.A. only) or equivalent
Is the battery in good condition?
NO - Faulty battery
YES - GO TO STEP 2.
2. Current Leakage Test
Install the battery (page 21-6).
Check the battery current leakage test (Leak test: page 21-7).
Is the current leakage below 0.01 mA?
YES - GO TO STEP 4.
NO - GO TO STEP 3.
3. Current Leakage Test without Regulator/Rectifier
Disconnect the regulator/rectifier connector and recheck the battery current leakage.
Is the current leakage below 0.01 mA?
YES - Faulty regulator/rectifier
NO - • Shorted wire harness
• Faulty ignition switch
4. Alternator Charging Coil Inspection
Check the alternator charging coil (page 21-8).
Is the alternator charging coil resistance within 0.1 - 1.0Q (20°C/68°F)?
YES - Faulty charging coil
NO - GO TO STEP 5.
5. Charging Voltage Inspection
Measure and record the battery voltage using a digital multimeter (page 21-6).
Start the engine.
Measure the charging voltage (page 21-7).
Compare the measurements to the results of the following calculation.
STANDARD: Measured BV < Measured CV < 15.5 V
• BV = Battery voltage
• CV = Charging voltage
Is the measured charging voltage within the standard voltage?
YES - Faulty battery
NO - GO TO STEP 6.
6. Regulator/Rectifier System Inspection
Check the voltage and resistance at the regulator/rectifier connector (page 21-8).
Are the measurements correct?
YES - Faulty regulator/rectifier
NO - • Open circuit in related wire
• Loose or poor contacts of related terminal
• Shorted wire harness
21-5
BATTERY/CHARGING SYSTEM (After '05)
BATTERY (TRX450ER)
REMOVAL/INSTALLATION
With the ignition switch OFF, remove the two bolts
and battery cover.
VOLTAGE INSPECTION
Measure the battery voltage using a commercially
available digital multimeter.
VOLTAGE (20°C/68°F):
Fully charged: 13.0 - 13.2 V
Under charged: Below 12.3 V
BATTERY TESTING
Remove the battery (page 21-6).
Refer to the instructions that are appropriate to the
battery testing equipment available to you.
TOOL:
Battery tester BM-210-AH (U.S.A. only), BM-210,
BATTERY MATE (MTP08-0192,
U.S.A. only) or equivalent
21-6
BATTERY/CHARGING SYSTEM (After '05)
BATTERY CHARGING (U.S.A. only)
Remove the battery (page 21-6).
Refer to the instructions that are appropriate to the
battery charging equipment available to you.
TOOL:
Battery charger Christie battery charger (MC1012/
2, U.S.A. only), BATTERY MATE
(MTP08-0192, U.S.A. only) or
equivalent
NOTICE
• To prevent a short, make absolutely certain
which are the positive (+) and negative (-) termi-
nals or cables.
• Do not disconnect the battery or any cable in the
charging system without first switching off the
ignition switch. Failure to follow this precaution
can damage the tester or electrical components.
Connect the tachometer.
With the headlight on, measure the voltage on the
multimeter when the engine runs at 5,000 rpm
(min 1 ).
STANDARD: Measured BV < Measured CV < 15.5 V
BV = Battery voltage (page 21-6)
CV = Charging voltage
21-7
BATTERY/CHARGING SYSTEM (After '05)
REGULATOR/RECTIFIER
WIRE HARNESS INSPECTION
Disconnect the regulator/rectifier 5P black connec-
tor.
Check the connector for loose contacts or corroded
terminals.
BATTERY LINE (TRX450ER)
Measure the voltage between the Red wire terminal
and ground.
There should be battery voltage at all times.
IGNITION SWITCH LINE (TRX450R)
Check the Red wire for continuity between the regu-
lator/rectifier and ignition switch connectors. REGULATOR/
There should be continuity. RECTIFIER
CHARGING COIL LINE (TRX450ER/R)
Measure the resistance between the Yellow wire ter-
minal.
STANDARD: 0.1 - 1.0 £1 (at 20°C/68°F)
Check for continuity between each Yellow wire ter-
minal and ground.
There should be no continuity.
REMOVAL/INSTALLATION
Disconnect the 5P black connector.
REGULATOR/
Remove the two bolts and regulator/rectifier from RECTIFIER
the frame.
Installation is in the reverse order of removal.
21-8
BATTERY/CHARGING SYSTEM (After '05)
GENERATING SYSTEM
GENERATING VOLTAGE INSPECTION
Start the engine and warm it up to the operating
temperature.
Stop the engine.
Remove the top cover (page 3-5).
TRX450ER: Disconnect the handlebar switch 6P natural connec-
tor.
TRX450R: Disconnect the handlebar switch 4P natural connec-
tor.
Connect the voltmeter positive (+) probe to the
Black wire terminal and negative (-) probe to the
Green wire terminal of the wire harness side han-
dlebar switch connector.
Restart the engine.
Measure the generating voltage when the engine
runs at 5,000 rpm.
HANDLEBAR SWITCH 6P (TRX450ER) or 4P
The voltage will STANDARD: 1 3 - 1 6 V
(TRX450R) CONNECTOR
drops about 1 V
when the Connect the handlebar switch 6P (TRX450ER) or 4P
coolingfan motor is (TRX450R) natural connector.
running. Install the top cover (page 3-5).
21-9
BATTERY/CHARGING SYSTEM (After '05)
ALTERNATOR
21-10
BATTERY/CHARGING SYSTEM (After '05)
LEFT CRANKCASE COVER REMOVAL
Drain the engine oil (page 4-15).
Remove both front fenders (page 3-6). ALTERNATOR CONNECTORS
Disconnect the alternator connectors and regulator/
rectifier connector.
Remove the wire bands and free the alternator wire
from the frame.
REGULATOR/RECTIFIER CONNECTOR
21-11
BATTERY/CHARGING SYSTEM (After '05)
STATOR REPLACEMENT
Remove the left crankcase cover (page 21-11).
GROMMET STATOR
Remove the four bolts, wire clamp and ignition
pulse generator.
Remove the three socket bolts, wire grommet and
alternator stator from the left crankcase cover.
Install the alternator stator into the left crankcase
cover and tighten the three socket bolts to the spec-
ified torque.
TORQUE: 9.8 N m (1.0 kgf-m, 7 Ibfft)
Install the wire grommet into the left crankcase
cover groove properly. CLAMP
Install the ignition pulse generator and wire clamp IGNITION PULSE
and tighten the four bolts to the specified torque. GENERATOR
FLYWHEEL INSTALLATION
Clean any oil from the tapered portion of the crank-
shaft and flywheel.
Install the woodruff key into the crankshaft key
groove.
21-12
BATTERY/CHARGING SYSTEM (After '05)
Install the flywheel onto the crankshaft by aligning *T. V \A/UPPI
the key way with the woodruff key.
Apply oil to the flywheel nut threads and seating
surface.
Install the washer and flywheel nut.
Hold the flywheel using the special tool and tighten
the flywheel nut to the specified.
TOOL:
Flywheel holder 07725-0040000 or
equivalent
commercially
available
DOWEL PINS
am
Install the left crankcase cover, cable holder and F^ABLE BREATHER HOSE
bolts. ' -^_
Connect the breather hose.
21-13
BATTERY/CHARGING SYSTEM (After '05)
Install the wire bands.
21-14