Process Control
Process Control
Process Control
27.1 Introduction
Most industrial processes require that certain variables such as temperature, flow, level or
pressure and concentration, remain at or near some reference value (set-point). The set-point is a
value for a process variable that is desired to be maintained. A closed control loop exists where a
process variable is measured, compared with a set-point and action is taken to correct any
deviation from the set-point. The system that serves to maintain a process variable at the set
point is called controller which is the part of a control system. In automatic control system,
controller performs the basic operation used by many systems provides regulation or command
to the process variable to be controlled. Our goal using this type of feedback control is to
determine the value or state of some physical quantity and often to maintain it at that value,
despite variations in the system or the environment.
Automatic control system provides the means of attaining optimal performance of dynamic
systems and improving productivity. This defines as a series of operations during which some
materials are placed in more useful state by continually measuring process variables (A process
variable is a condition of the process fluid that can change the manufacturing process in some
way) and taking actions such as opening valves, slowing down pumps and turning up heaters so
that the measured process variables are maintained at operator specified set point values. Mainly
there are four basic objectives of automatic process control which are as under.
1. Suppressing the influence of external disturbances
2. Optimizing the performance
3. Increasing the productivity
4. Cost effective
A control system is that means by which any quantity of interest in a machine or mechanism can
be changed, maintained or unaltered in accordance with desired manner. This system uses an
interconnection of components forming a system configuration that will provide a desired system
response. Input Signals flow through the system and produce an output as shown in Fig.27.1(a).
Fig. 27.1 (a) Representation of input and output of a process
The input will usually be an ideal form of the output. In other words the input is really what we
want the output to be. It's the desired output. The output of the system has to be measured. In
the Fig. 27.1 (b), we have shown the system in which we are trying to control - the "plant" and a
sensor that measures what the controlled system is doing.
The input to the plant is usually called the control effort, and the output of the sensor is usually
called the measured output, as shown Fig. 27.1 (b).
For example, if we want the output to be 100�C, then that's the input.
To control the process output, it is necessary to first measure the process output which is to be
controlled at a desired set point. The sensor measures the actual process output. In the block
diagram representation (Fig. 27.2), the sensor senses the process-output temperature and
generates a proportionate output signal. A sensor might be an LM35, which produces a voltage
proportional to temperature - if the output signal is a temperature. Sensor is needed in the system
to measure what the system is doing. The sensor measures the output e.g. temperature of the
system to be controlled, and converts it into proportionate electrical signal. The LM35
temperature sensors, for example, produce 0.01 volts for every 1.0�C change. To control the
system we need to use the information provided by the sensor. Usually, the output, as measured
by the sensor is subtracted from the input (which is the desired output) as shown in Fig. 27.2.
That forms an error signal that the controller can use to control the plant.
Fig. 27.2 Representation of input and output of a process with error comparator
The device which performs the subtraction to compute the error E is a comparator. Finally, the
last part of this system is the controller which is as shown in Fig.27.3.
The controller receives the error signal from the comparator and generates an actuating signal
which can be used to control the process-output through the actuating element. Thus, the
controller has two functions:
1. To compute what the control effort should be.
2. To apply the computed control effort.
The closed-loop system is also called the feedback system. Feedback control system is to control
the process by using the difference between the output and reference input. A closed-loop control
system uses a measurement of the output and feedback of this signal to compare it with the
desired output (reference or command) as explained above in Section 27.2.
Fig. 27.6 shows the block diagram of generalized process control and the function of each block
are given as follows:
1. Process
The term Process as used in relation to process control refers to the methods of converting
raw materials into the end product(s). The raw materials which either pass through or remain
in a liquid, gaseous, or slurry (a mix of solids and liquids) state during the process, are
transferred, measured, mixed, heated or cooled, filtered, stored, or handled in some other way
to produce the end product. Many dynamic variables may be involved in a process, and it
may be desirable to control all these variables at the same time. There are single-variable
processes, in which only one variable is to be controlled. However, most industrial processes
are multivariable processes, in which many variables, perhaps interrelated, may require
regulation.
2. Measurement
To perform control, it is necessary to measure the process parameter, so that we can have
information on the variable itself. In general, a measurement refers to the transduction of the
variable into some corresponding analog of the variable, such as a pneumatic pressure, an
electrical voltage, or current. A transducer is a device that performs the initial measurement
and energy conversion of a dynamic variable into analogous electrical or pneumatic
information. Further transformation or signal conditioning may be required to complete the
measurement function. The result of the measurement is a transformation of the dynamic
variable into some proportional information in a useful form required by the other elements
in the process-control loop.
3. Evaluation
The next step in the process-control sequence is to examine the measurement and determine
what action, if any, should be taken. The evaluation may be performed by an operator, or by
electronic/pneumatic signal processing, or by a computer. A controller is a device that
receives data from a measurement instrument, compares that data to a programmed set-point,
and, if necessary, signals a control element to take corrective action. Computer use is
growing rapidly in the field of process control because it is easily adapted to the decision
making operations and because of its inherent capacity to handle control of multivariable
systems. The controller requires an input of both a measured representation of the dynamic
variable and a representation of the desired value of the variable, expressed in the same terms
as the measured value. The desired value of the dynamic variable is referred to as the set
point. Thus, the evaluation consists of a comparison of the controlled variable measurement
and the set point and a determination of action required to bring the controlled variable to the
set point value.
4. Control element
The correcting or final control element is the part of the control system that acts to physically
change the manipulated variable. This element accepts an input from the controller, which is
then transformed into some proportional operation performed on the process. In any process
control loop, final control elements are typically used to correct a variable that is out of set-
point.
In most cases, the final control element is a valve/servo motor used to restrict or cut off fluid
flow, but motors, louvers (typically used to regulate air flow), solenoids, and other devices
can also be final control elements. For example, a final control element may regulate the flow
of fuel/air to a burner to control temperature, the flow of a catalyst into a reactor to control a
chemical reaction.
A block diagram can be used simply to represent the composition and interconnection of a
system. Also, it can be used together with transfer function to represent the cause and effect
relationship throughout the system. Transfer Function defines the relationship between an
input signal and an output signal for a system.
To further illustrate, the block diagram concept in Fig. 27.7 shows a typical flow control
system. In this example, the dynamic variable is the flow rate that is converted to electric
signal as an analog. The process is the flow, and the measurement is to determine the
difference of pressure. With the set point in the controller, the flow of the process is
controlled through the control element i.e. the valve.
Fig. 27.7 Process Control System to regulate flow and the corresponding block diagram
Here the dynamic variable is the liquid temperature T L. This temperature depends on many
parameters in process like input flow rates in pipe A, output flow rates via pipe B, ambient
Temperature TA, the steam temperature Ts, inlet temperature To, and the steam flow rates Q S. In
this case, steam flow rate is the controlling parameter. If one of other parameters changes,
accordingly there is change in temperature results. In order to bring the temperature back to the
original value the steam flow rate is adjusted accordingly. This can be described by a process
equation where liquid temperature is a function as:
Process load refers to set of all parameters excluding the dynamic variable. At some point in
time, a process load change causes a change in dynamic variable e.g. when all parameters in a
process have their nominal values, it is known as the nominal load on the system. The required
control parameters value under these conditions is the nominal value of that parameter. If the set
point is changed, then the control parameter is altered to cause the variable to adopt new
operating point. The load is still nominal, however, because of other parameters are assumed
unchanged. Now if one of the parameters changes from nominal value, causing a corresponding
shift in the controlled variable then a process load change is said to have occurred.
It represents a delay in reaction of controlled variable to a change of load variable e.g. the
process control loop in a process responds to assure, some finite time later that the variable
returns to set point value. Part of this time is consumed by the process itself and referred to as
process lag. Process time lags are affected by capacitance which is the ability of a process to
store energy; resistance, the part of the process that opposes the transfer of energy
between capacities and transportation time, the time required to carry a change in a process
variable from one point to another in the process. This time lag is not just a slowing down of
a change, but rather the actual time delay during which no change occurs.
27.5.3 Self-regulation
Self regulation is characteristic that a dynamic variable adopts some nominal value
commensurate with the load with no control action. The output will move from one steady state
to another for the sustained change in input. This means that for change in some input variable
the output variable will rise until it reaches a steady state (inflow = outflow). It is the tendency of
the process to adopt a specific value of controlled variable for nominal load with no control
operations. A significant process characteristic is its tendency to find a specific value of dynamic
variable for nominal load with no control operations. The control operations may be significantly
affected by such self-regulation. The process of Fig. 27.8 has self regulation as shown by the
following arguments:
(a) Suppose we fix the steam valve at 50 % and open the control loop so that no changes in
valve position are possible.
(b) The liquid heats up until the energy carried away by the liquid equals that input energy from
the steam flow.
(c) If load changes, a new temperature is adopted (because the system temperature is not
controlled).
(d) The process is self regulating because the temperature will not run away but stabilizes.
Lesson 28
CONTROL SYSTEM PARAMETERS
28.1 Introduction
A control system monitors and determines a difference between a desired and measured
parameter values, applies a weighting factor to the difference and selects a control strategy based
on the weighted difference. The weighting factor generally reflects the confidence in the
accuracy of the parameter value determined by the parameter monitor. The weighting factor may
be determined based on one or more ambient operating conditions or parameters, or on statistical
analyses of monitor values and/or control system parameter values.
28.2.1 Error
Error is the difference between the measured variable and the setpoint. Error can be either
positive or negative. The objective of any control scheme is to minimize or eliminate error. The
deviation or error of dynamic variable from set point is given by:
�����������E = Cm - Csp
�����������Where E = error
� ���������Cm = measured value of variable
�����������Csp = set point of variable
The above equation expresses error in an absolute sense, usually in units of measured analog of
control signal. Note that a positive error indicates a measurement above the set points whereas a
negative error indicates a measurement below the set point.
The dynamic variable under control or controlled variable has a range of values within which
control is required to be maintained at set point. This range can be expressed as the minimum
and maximum values of the dynamic variable or the nominal value plus and minus the spread
about this nominal value e.g. if a standard signal 4-20 mA transmission is employed, then 4 mA
represents the minimum value of the variable and 20 mA the maximum value.
It is the possible range of values of final control element. The controller output is expressed as a
percentage where minimum controller output is 0% and maximum controller is 100%. But 0%
controller output does not mean zero output. For example, it is necessary requirement of the
system that a steam flow corresponds to 1/4 th opening of valve. The controller parameter output
has a percentage of full scale when the output changes within the specified limits in expressed as:
Processes have the characteristic of delaying and retarding changes in the values of the process
variables. This characteristic greatly increases the difficulty of control. The control system can
have a lag associated with it. The control lag is the time required by the process and controller
loop to make the necessary changes to obtain the output at its set point. The control lag must be
compared with process lag while designing the controllers. A process time lag is the general term
that describes the process delays and retardations. It refers to the time for the process control
loop to make necessary adjustments to the final control element e.g. if a sudden change in liquid
temperature occurs, it requires some finite time for the control system to physically actuate the
steam control valve.
Sometimes a dead zone is associated with the process control loop. The time corresponding to
dead zone is called dead time. This is the elapsed time between the instant a deviation (error)
occurs and when the corrective action first occurs.
The method used by the controller to correct the error is the control mode. Controller modes are
an expression of relation between controller output and dynamic variable deviation from the set
point. The actions of controllers can be divided into groups based upon the functions of their
control mechanism. Each type of controller has advantages and disadvantages and meets the
needs of different applications. Grouped by control mechanism function, the two types of
controllers are:
1. Discontinuous controllers
2. Continuous controllers
In this mode there is a possibility of smooth variation in control parameter and the controllers
automatically compare the value of the process variable to the set-point to determine if an error
exists. If there is an error, the controller adjusts its output according to the parameters that have
been set in the controller. When there is an error, the controller makes a change in its output. It
determines:
� How much? Proportional Mode
� How long? Integral Mode
� How fast? Derivative Mode
In this mode controller command initiates a discontinuous change in control parameter. The
manipulated variable of a discontinuous controller mode can only be changed in set steps. The
best-known discontinuous-action controller is the two-step control that can only assume the
conditions �on� or �off�. An example is the thermostat of a hot air oven. It switches the
electric current for the heating element �on� or �off� depending on the set temperature.
The choice of operating modes for any given process control system is a complicated decision. It
involves not only process characteristics but cost analysis, product rate, and other industrial
factors. The different types of discontinuous controller operating modes are defined as follows:
(A) Two Position Controller Mode: A two position controller mode uses a device that has
two operating conditions: completely on or completely off. These also called ON-OFF control
or Discrete controllers. On /off control activates an output until the measured value reaches the
reference value. Fig. 28.1 shows the input to output characteristic for a two position controller
for a refrigerator that switches from its �OFF� to its �ON� state when the measured variable
increases above the set point.
Conversely, it switches from its �ON� state to its �OFF� state when the measured
variable decreases below the set point. This device provides an output determined by whether
the error signal is above or below the set point. The magnitude of the error signal is above or
below the set point. The magnitude of the error signal past that point is of no concern to the
controller.
While simple and low cost, this mode of control has a tendency to overshoot the desired value.
Flow Diversion Valve (FDV) used in HTST plant and solenoid valves are two position ON-OFF
controller.
In this control mode, specific output of the controller is not uniquely determined by error. If error
is zero, the output will not change but remains (floats) at whatever settings it was when the error
went to zero. When the error moves off zero, the controller output begins to change e.g. a
floating control will operate a control valve which, as level rises and falls will throttle down or
gradually open a level control valve in the inlet (or outlet) line, thereby controlling the level at a
pre-set height in the tank.
Lesson 29
TYPES OF CONTROLLER MODES
In the proportional (throttling) mode, there is a continuous linear relation between value of the
controlled variable and position of the final control element. In this control mode, the output of
the controller is proportional to error e(t). The relation between the error e(t) and the controller
output p is determined by a constant called proportional gain constant denoted as K p. The output
of the controller is a linear function of e(t).
The direct and reverse action is possible in the proportional controller mode. The error may be
positive or negative because error (r-b) depending upon whether b is less or greater than the
reference setpoint r(t).
If the controlled variable i.e. input to the controller increases, causing increase in the controller
output, the action is called direct action. For example the output valve is to be controlled to
maintain the liquid level in a tank. If the level increases, the valve should be opened more to
maintain the level. On the other hand if the variable decreases, causing increase in the controller
output, the action is called reverse action. Conversely, increase in the controlled variable,
causing decrease in controller output is also a reverse action.
Proportional gain is the percentage change of the controller output relative to the percentage
change in controller input. Gain, also called sensitivity, compares the ratio of amount of change
in the final control element to amount of change in the controlled variable. Mathematically, gain
and sensitivity are reciprocal to proportional band. The gain kP can be expressed as:
�����������KP = 100 / P
�����������Where
�����������������������P = proportional band
The gain determines how fast the system responds. If the value is too large the system will be in
danger to oscillate and/or become unstable. If the value is too small the system error or deviation
from set point will be very large.
Proportional band, (also called throttling range), is the change in value of the controlled variable
that causes full travel of the final control element. The proportional band of a particular
instrument is expressed as a percent of full range. For example, if full range of an
instrument is 200oF and it takes a 50oF change in temperature to cause full valve travel,
the percent proportional band is 50oF in 200oF, or 25%.
The proportional band P, express the value necessary for 100% controller output. If P = 0, the
gain or action factor kP would be infinity - the control action would be ON/OFF.
29.1.4 Offset
Offset, also called droop, is deviation that remains after a process has stabilized. Offset is an
inherent characteristic of the proportional mode of control.
de (t)
����������� =K i e(t )
dt
The constant Ki is also called integral constant. Integrating the above equation, the actual output
at any time t can be obtained as
29.2.1 Advantages
1. Integral controllers tend to respond slowly at first, but over a period of time they tend to
eliminate errors.
2. The integral controller eliminates the steady-state error, but has the poor transient response
and leads to instability.
1. If error is zero, the output remains at a fixed value equal to what it was, when the error
become zero.
2. If the error is not zero, then the output begins to increase or decrease, at a rate Ki % per
second for every � 1 % of error.
3. The inverse of Ki is called integral time and denoted as Ti.
1
�����Ti= =Integral Time
Ki
The comparison of proportional and integral mode behavior at the time of occurrence of an error
signal is given in Table 29.1.
It can be seen that proportional mode is more favorable at the start while the integral is better for
steady state response. In pure integral mode, error can oscillate about zero and can be cyclic.
Hence in practice, integral mode is never used alone but combined with the proportional mode,
to harness the merits of both modes.
In this mode, the output of the controller depends on the rate of change of error. Hence, it is also
called rate action mode or anticipatory action mode. The mathematical equation for the mode is:
�����������
�����������Where Kd = Derivative gain constant
The derivative gain constant indicates by how much % the controller output must change for
every % per second rate of change of the error. Generally Kd is expressed in minutes. The
important feature of this type of control mode is that for a given rate of change or error signal,
there is a unique value of the controller output.
The advantage of the derivative control action is that it responds to the rate of change of error
and can produce the significant correction before the magnitude of the actuating error becomes
too large. Derivative control thus anticipates the actuating error, initiates an early corrective
action and tends to increase stability of the system, improving the transient response. The
derivative or differential controller is never used alone because when error is zero or constant,
the controller has either no output or the nominal output for zero error.
For a given rate of change of error signal, there is a unique value of the controller output. When
the error is zero, the controller output is zero. When the error is constant i.e. rate of change of
error is zero, the controller output is zero. When the error is changing, the controller output
changes by Kd % for even 1 % per second rate of change of error.
When the error is zero or a constant, the derivative controller output is zero. Hence, it is never
used alone. Its gain should be small because faster rate of change of error can cause very large
sudden change of controller output. This may lead to instability of the system.
29.4.2 Advantages
1. With sudden changes in the system the derivative controller will compensate the output fast.
2. The long term effects the controller allows huge steady state errors.
3. A derivative controller will in general have the effect of increasing the stability of the
system, reducing the overshoot, and improving the transient response.
Due to offset error, proportional mode is not used alone. Similarly, integral and derivative modes
are not used individually in practice. Thus, to take the advantages of various modes together, the
composite control modes are used. Composite modes of controller operation combine advantages
of each �pure� mode. The various composite control modes are:
1. Proportional + Integral mode (PI)
2. Proportional + Derivative Mode (PD)
3. Proportional + Integral + Derivative Mode (PID)
This is a control mode that results from a combination of proportional mode and integral mode.
The analytical expression for this is:
�����������p(t) = Kp e(t) + Kp Ki ∫ e(t) dt + p(0)
The main advantage of this composite control mode is that the one-to-one correspondence of
proportional mode is available and integral mode eliminates the inherent offset.
This system cannot eliminate the offset of proportional controllers. However, it can handle fast
process load changes as long as the offset error is acceptable.
The three mode controller uses proportional, integral and derivative (PID) action and is the most
versatile of all controller actions. The proportional part of this controller multiplies the error by a
constant. The integral part integrates the error. Finally, the derivative part differentiates the error.
The functions of the individual proportional, integral and derivative controllers complement each
other. If they are combined it is possible to make a system that responds quickly to changes
(derivative), tracks required positions (proportional), and reduces steady state errors (integral).
The output of the controller is the sum of the previous three signals as given in the following
equation:
de (t)
����������� p ( t ) =Kp e ( t )+ K p K i∫ e (t)dt+ Kp Kd + p (0)
dt
Where Kp, Ki and Kd are the proportional, integral and derivative gains respectively.
The proportional, integral and derivative terms must be individually adjusted or �tuned� to a
particular system.
29.8.1 Advantages
30.1 Introduction
Final control elements are devices that complete the control loop. They link the output of the
controlling elements with their processes. Some final control elements are designed for specific
applications. The final control element is the last element of the closed control loop that
implements the control action. It receives the output signal (control or actuating signal) from a
process controller and adjusts accordingly the value of the manipulated variable by changing the
amount of matter or energy entering the process in a way to bring the controlled variable
(process variable) to its set point. The final control element is probably the most important
because it exerts a direct influence on the process.
For example, neutron-absorbing control rods of a reactor are specifically designed to regulate
neutron-power level. However, the majority of final control elements are general application
devices such as valves, dampers, pumps, and electric heaters. Valves and dampers have similar
functions. Valves regulate flow rate of a liquid while dampers regulate flow of air and gases.
Pumps, like valves, can be used to control flow of a fluid. Heaters are used to control
temperature.
Control valves are used primarily to throttle energy in a fluid system and not only for shut-off
purposes. Their internals must withstand high fluid velocity and turbulence for long periods
without maintenance. A control valve is simply a variable orifice that is used to regulate the flow
of a process fluid according to the requirements of the process.
Fig. 30.1 illustrates a typical globe-type control valve body in both the fully open and fully
closed positions. In a control valve, an actuator that is connected to the valve�s plug stem
moves the valve between the open and closed positions to regulate flow in the process. The valve
body is mounted in the process fluid line and is used to control the flow of fluid in the process.
The body of a control valve is generally defined as the part of the valve that comprises the main
boundary, including the connecting ends. Valves are classified into two general types based on
the movement of the valve�s closure part: linear and rotary.
An actuator is the part of a final control device that causes a physical change in the final control
device when signaled to do so. The most common example of an actuator is a valve actuator,
which opens or closes a valve in response to control signals from a controller. By themselves,
valves cannot control a process. Manual valves require an operator to position them to control
a process variable. Valves that must be operated remotely and automatically require special
devices to move them. These devices are called actuators. Actuators are often powered
pneumatically, hydraulically, or electrically. Diaphragms, bellows, springs, gears, hydraulic pilot
valves, pistons, or electric motors are often parts of an actuator system. There are four principal
types of actuator:
� Pneumatic
� Hydraulic
� Solenoid
� Electric Motor
The pneumatic valve is an air-operated device which controls the flow through an orifice by
positioning appropriately a plug (Fig. 30.2 and 30.3).
The plug (1) is placed in the orifice (2) of the valve and attached to the end of the stem (3). The
orifice is placed inside the body of the valve (4) made of cast iron, alloy steels, alloy steels plus
corrosion-resistant alloys, or bronze. The upper part of the final control element is an actuator
(5). A diaphragm (6) divides this actuator in two chambers. The upper end of the stem is
supported on the diaphragm. When the airs pressure (the output signal from a pneumatic
controller) above the diaphragm increases, the diaphragm deflects and the stem moves
downwards thus restricting by the plug flow of the fluid through the orifice. This type of a
pneumatic valve is called �air-to-close� valve.
Fig. 30.3 Air-to-open pneumatic actuator with valve
When the air pressure goes down the stem under the action of a spring (7) will move upwards,
thus opening the orifice. There is another type of valves, which operate in opposite action, i.e.,
when the air pressure increases the plug opens the orifice. Such valves are called �air-to-open�
valves. If the air pressure varies from 20 to 100 kPa the plug is moved from a fully open to fully
closed position.
Pneumatic actuators are normally used to control processes requiring quick and accurate
response, as they do not require a large amount of motive force. However, when a large amount
of force is required to operate a valve (for example, the main steam-stop valves), hydraulic
actuators are normally used. Hydraulic actuators use fluid displacement to move a piston in
a cylinder positioning the valve as needed for 0-100% fluid flow. Although hydraulic
actuators come in many designs, piston types are most common.
It consists of a cylinder, piston, spring, hydraulic supply and returns line, and stem. The piston
slides vertically inside the cylinder and separates the cylinder into two chambers. The upper
chamber contains the spring and the lower chamber contains hydraulic oil. The hydraulic supply
and return line are connected to the lower chamber and allows hydraulic fluid to flow to
and from the lower chamber of the actuator. The stem transmits the motion of the piston to a
valve.
When the hydraulic force is greater than the spring force, the piston begins to move
upward, the spring compresses, and the valve begins to open. As the hydraulic pressure
increases, the valve continues to open. Conversely, as hydraulic oil is drained from the cylinder,
the hydraulic force becomes less than the spring force, the piston moves downward, and
the valve closes. By regulating amount of oil supplied or drained from the actuator, the
valve can be positioned between fully open and fully closed.
Solenoid actuators are used on small valves and employ an electromagnet to move the
stem which allows the valve to either be fully open or fully closed. A typical electric solenoid
actuator is shown in Fig. 30.5. It consists of a coil, armature, spring, and stem.
Fig. 30.5 Electric solenoid actuator
The coil is connected to an external current supply. The spring rests on the armature to force it
downward. The armature moves vertically inside the coil and transmits its motion through the
stem to the valve.
When current flows through the coil, a magnetic field forms around the coil. The magnetic field
attracts the armature toward the center of the coil. As the armature moves upward, the spring
collapses and the valve opens. When the circuit is opened and current stops flowing to the coil,
the magnetic field collapses. This allows the spring to expand and shut the valve.
A major advantage of solenoid actuators is their quick operation. Also, they are much easier to
install than pneumatic or hydraulic actuators. However, solenoid actuators have two
disadvantages. First, they have only two positions: fully open and fully closed. Second, they
don�t produce much force, so they usually only operate relatively small valves.
An electric motor is composed of a rotating center, called the rotor and a stationary outside, and
called the stator. These motors use the attraction and repulsion of magnetic fields to induce
forces, and hence motion. Equipped with limit switches and/or torque limiters, the electric motor
actuator has the capability of 0-100% control and has not only a motor but also a manual hand
wheel, and a clutch and gearbox assembly.
Typical electric motors use at least one electromagnetic coil, and sometimes permanent magnets
to set up opposing fields. When a voltage is applied to these coils the result is a torque and
rotation of an output shaft. There is a variety of motor configuration the yields motors suitable
for different applications. Most notably, as the voltages supplied to the motors will vary the
speeds and torques that they will provide.
Electric motor actuators vary widely in their design and applications. Some electric motor
actuators are designed to operate in only two positions (fully open or fully closed). Other
electric motors can be positioned between the two positions. A typical electric motor actuator is
shown in Fig. 30.6. Its major parts include an electric motor, clutch and gear box assembly,
manual hand wheel, and stem connected to a valve.
The motor moves the stem through the gear assembly. The motor reverses its rotation to either
open or close the valve. The clutch and clutch lever disconnects the electric motor from the gear
assembly and allows the valve to be operated manually with the hand wheel.
Most electric motor actuators are equipped with limit switches, torque limiters, or both. Limit
switches de-energize the electric motor when the valve has reached a specific position. Torque
limiters de-energize the electric motor when the amount of turning force has reached a specified
value. The turning force normally is greatest when the valve reaches the fully open or fully
closed position. This feature can also prevent damage to the actuator or valve if the valve binds
in an intermediate position.
Lesson 31
INSTRUMENTATION AND CONTROLS IN DAIRY PLANT
When the green button (marked Start) is pressed the electric circuit provides the supply to the
Solenoid Coil (SC). The coil becomes an electromagnet and attracts the steel Armature to the
left. This movement of armature makes the contact of movable contactors to the fixed contactors
and completes the circuit through the ends A and B, thus giving the power supply to any
equipment connected to the terminals at the end B. The start button opens up when our finger is
removed from the button. But the current to coil is maintained through auxiliary contacts A&B,
which is connected in parallel to the Green button switch as shown in the figure. By closing the
Red button the circuit to the coil breaks and the control spring pulls the movable contactors to
the right, thus cutting the power supply and the equipment stops.
In the above figure the SW is the switch, it could be a manual start switch or a switch operated
by any of the equipment used for the controlling parameters like, pressure, temperature, flow etc.
By closing the switch SW power is supplied to the solenoid through SW. A pilot valve PV is
attached to the armature of the solenoid. When the SW is closed the movement of the armature
opens the pilot valve and the compressed air enters the SS Cylinder. The compressed air at the
pressure of 2-3 kg/cm2 moves the piston down and closes the milk valve. The reverse happens
when the SW is disconnected. The air supply to the cylinder is closed and the air is exhausted
from the cylinder (not shown in the figure). Now the movement of the valve is carried out by the
control spring and the milk valve is opened.
Figure 3.3 shows a self acting steam thermostat with glycerin liquid, commonly used in dairy
plants. A SS sensing bulb filled with glycerin under pressure is immersed in the tank, the
contents of which are heated by steam. As the temperature increases the glycerin liquid expands
in proportion to the temperature at the sensing bulb. This pushes the piston in the valve and the
steam supply is regulated by the steam valve. The glycerin is used because its volumetric
expansion is quite high and enough to generate power to operate the steam valve.
The online density transducer, as shown in figure 3.4, is used in the computerized dairy plants
for sensing density, total solids, fat, temperature etc. The density measurement is based on
measuring the period of oscillation of a mechanical oscillator operated at its normal frequency.
The oscillator consists of two straight parallel tubes, which are flown through by the sample. The
period of oscillation depends upon the density of the sample within the mechanical oscillator and
the mechanical properties of the, like inner diameter, wall thickness, elasticity etc. of the applied
tube. Both density and mechanical properties of the tube depend on the temperature of the
sample. Thus temperature is also measured and transmitted. The signal processor computes the
density, temperature etc. and extrapolates information of total solids, dry weight, fat percent etc.
in the sample.
In HTST pasteurizer the raw milk / product is pumped from a constant level tank to the heating
section where the temperature is raised to exceed the pasteurization lower limit. The hot product
temperature is measured and recorded at the end of the holding tube. If the temperature is less
than the pasteurization temperature, the product is sent back to the constant level tank by the
flow diversion valve and is recycled. Once the temperature exceeds the pasteurization
temperature the flow diversion valve routs the product to the forward flow to the regenerator and
cooling sections of the heat exchanger. The operation of a flow diversion controller of an HTST
pasteurizer is shown in figure 31.5.
A SS temperature sensing bulb is inserted in the milk line that senses the temperature and
provides proportionate signal to the Bourdon element by expansion of liquid through a capillary.
The position of the contact �A� attached to the Bourdon element is guided by the movement
of the free end of the Bourdon element. As soon as the temperature of milk exceeds 72.5 oC the
contacts A-B closes. This switches on the micro-switch (MS) that provides the 24 V DC supply
to the solenoid operated pilot valve (PV). When the pilot valve opens compressed air enters the
cylinder pushes the piston P2 downwards. The stem of the flow diversion valve then moves to the
downward position and closes the diverted flow port. Milk thus enters the forward flow line. The
reverse happens when the temperature of milk is less than 72.5oC, resulting in the diverted flow.
Complete control system of a HTST pasteurization plant is given in figure 31.6 showing the flow
recorder controller and the temperature recorder controller. The temperature recorder controller
gets the input with regards to the temperatures of hot water, temperature of milk at the end of the
holding tube and the temperature of pasteurized chilled milk. Hot water is normally used to heat
the milk in a plate heat exchanger. Steam is introduced to the water tank, and the temperature of
hot water is normally kept 2 to 3oC above the pasteurization temperature. The temperature of hot
water is sensed and sent to temperature controller. Heating will continue until the preset
temperature vale is reached.
The outlet air temperature in a spray drying chamber is controlled by keeping the inlet air
temperature at a constant level and varying the milk input. The schematic diagram of outlet air
temperature control in the spray dryer is given in Fig. 31.7
A thermistor sensing device senses the air temperature at the outlet of drying chamber at point
(2). A Wheatstone bridge circuit is used to compare the measured temperature with the desired
temperature. The output of the signal processor at (3) operates the servomotor (4), which rotates
in either direction depending upon the outlet air temperature, whether it is more or less than the
desired value. The servomotor controls the pressure of oil between the set of clutch plates
through a pressure reducing valve. This controls the speed of milk pump and hence the milk
input to the dryer to maintain a constant temperature at the outlet.
Lesson 32
INSTRUMENTATION AND CONTROLS IN CIP CLEANING AND SANITIZING
32.1 Introduction
Cleaning-In-Place (CIP) and Sterilization-In-Place (SIP) are systems designed for automatic
cleaning and disinfecting of the dairy equipments without major disassembly and assembly
work. The CIP system allows cleaning one part of the plant while other areas continue to
produce product. Furthermore, a modern CIP system will not only save money in terms of higher
plant utilization but also due to significant savings in cleaning solutions, water and labour
requirement. The system also ensures the operator safety and minimized product change over
time.
CIP (cleaning-in-place) covers a variety of areas but its main purpose is to remove solids and
bacteria from tanks, vessels, and pipe work in the dairy processing equipments. The type of
cleaning medium or detergents includes caustic, acid, disinfectant, return water and the fresh
water. The detergents are usually recycled. The number of CIP circuits depends upon the plant
areas to be cleaned and the required availability for the same. The number of tanks in the CIP
circuit depends on the required detergent and disinfectant volumes; however the number rarely
exceeds 8 tanks per system. The volume of the tanks is as per the effective volume needed for
the cleaning. The flow rates of detergents in the system are kept normally up to 150 m�/h.
32.3 CIP System Configuration and Layout
A CIP system consists of piping for distribution and return of cleaning agents, tanks and
reservoirs for cleaning solutions, heat exchangers spray heads, flow management devices and
programmable control unit. Two main types of CIP systems are available: single-use units, in
which all cleaning solutions are used once and discarded and the reuse units which use the
cleaning media and rinse liquid more than once. The latter type of system recovers the
recirculated alkali which is stored for the next cleaning event. Single use systems are preferred
when there is a concern of cross contamination. For acid and alkali recirculation, concentrated
solutions are metered into deionized water-filled acid / alkali tanks. The contents of the tank are
mixed by recirculation through CIP supply pump. A heat exchanger heats the solution to the
desire temperature. Temperature of the return flow is monitored and recorded. The steam supply
to the heat exchanger is controlled by the return flow temperature signal during recirculation of
the alkaline detergent. Dry running of supply pump is prevented by no-flow sensors. During the
final water wash, the conductivity sensor is used to monitor the return flow which is sent to drain
when a preset low conductivity value is reached indicating complete removal of acid or alkali
from the system. Sensors are provided to monitor the strength of cleaning solutions. Sometimes,
the cleaning solutions are dosed in line.
In simple and smaller facilities manual operation of CIP cleaning is followed. CIP cleaning of
large or complex processing plant requires automation and micro-processor based controls, with
PLCs. The PLCs are programmed with several different cleaning progarmmes, one for each
cleaning facility. The programme specifies the cleaning route, sequence of cleaning, the flow
rates and the temperatures and strength of cleaning media. The duration of each cleaning
programme is fixed. Each control valve in the line is monitored using positive feedback. In the
event of a failure the system is designed to safe shut down.
The circuit diagram of automated CIP system is given in the Figure 32.1
Fig. 32.1 CIP system automation
In the figure the T1, T2, T3, and T4 are the Tanks for luke warm water, hot water, alkali (sodium
hydroxide) and nitric acid solutions. The heating is done by steam and the temperature in the
tanks is controlled by steam thermostat. The milk flow path is denoted by MFP and all the milk
contact surfaces of the equipments such as separator, homogenizers, plate heat exchangers,
pasteurizers are connected series. The valves V 1 to V9 are the air operated heavy duty valves
which are operated by pilot valves. The valve V 9 is the drain valve. P1 and P2 are the forward
and the return flow pumps respectively. SV represents the solenoid valve for compressed air
flow. S1 and S2 are the Solution Analyzers to control the concentration of Lye and Acid solutions
respectively. The Wheatstone Bridge type circuit is used where the conductivity (electrical
conductivity) of the solutions are compared to operate and control solution valves for injecting
on to CIP lines. The operation of the CIP system is illustrated in Figure 32.2.
To start the system the start button ST is switched on. This in turn switches on the
Electromagnetic Switching Relays R1 to R5. Now the power is ready for all the valves. The
various valves in the CIP system include; X 1 and X2 which are the air operated pilot valve for the
Rinse Water, X3 and X4 for Lye Solution, X5 and X6 for Hot Water flow, X7 and X8 for Acid
solution, Z1 is the compressed air solenoid valve, Z2 CIP drain valve and Z3, Y are the solution
analyzers valves. The power supply is controlled by electronic timers T 1 to T12, which switches
on / off at different times set for various valves for flow of cleaning solutions.
A simple automatic chlorinator using venturi flow meter is shown in figure 32.3. It consists of a
balloon of a flexible material which contains the chlorine solution. The flexible balloon is placed
in a fixed metallic or PVC drum. A venture tube is placed in the water supply line. Pressures
across the venturi tube are sensed and this pressure differential drives the flow if chlorine
solution (i) to the water line. The quantity of chlorine solution injected is proportional to the
pressure differential (P1-P2) which in turn is proportional to the flow of water. Hence chlorine is
injected at the constant rate to the water line. The system is designed for 50 ppm of free
chlorine.
Fig. 32.3 Automatic chlorinator