2lt Inboard Technical Drawing

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

SLOT THRU

FRONT & REAR 4X 139.2


[5.48]

SLOT THRU
FRONT & REAR

394.2
[15.52 ]
286
[11.26 ]

717.7
[28.3 ]

(286 )
[11.26 ]

SLOT THRU
RFOB FRONT & REAR
BACK OF BLOCK

SLOT THRU
802 FRONT & REAR
[31.57 ]
237.1 495.2
[9.34 ] [19.50 ]
22.8 710
REAR ENGINE [.90 ] [28.0 ]
LIFTING

SLOT THRU
60 $
WET EXHAUST OUTLET 30 $ 229.5
[9.03 ]

FRONT ENGINE LIFTING


OIL FILTER

502
76.1 [19.76 ] C
AUX. HEATER RETURN G
[3.00 ]
757
285.7 [29.8 ]
[11.25 ] 160.05 160.05
C [6.301 ] [6.301 ]
G CRANKSHAFT

(3)

214
[8.4 ] 95
[3.74 ]
FFOB

172.65 3.77
[6.797 ] [.148 ]
101.5
[4.00 ]
572
[22.52 ]
336 181.7
[13.2 ] [7.15 ]

370.9 193
[14.60] [7.6 ] NOTES:
(1) REFER TO THE APPLICATION MANUAL FOR COMPLETE PRODUCT INSTALLATION REQUIREMENTS.
589 (2) DIMENSIONS REQUIRE A MINIMUM OF 1/2 in. (13 mm) CLEARANCE FOR MOTOR MOUNT DEFLECTION.
[23.2] (3) INNER AND OUTER SURFACES OF TRANSOM MUST BE PARALLEL WITHIN 1/8 in. (3 mm) IN AREA COVERED BY TRANSOM
PLATES AND REMAIN WITHIN TRANSOM THICKNESS LIMITS.
(4) REFER TO "TRANSOM CUTOUT" IN THE INSTALLATION MANUAL TO FIND THE CRANKSHAFT CENTERLINE VS. BOAT BOTTOM.

REVISION UNITS SCALE SHEETS


8M4503637
2.0L TIER3 - VGT A
mm
(in)
1:12
25.4 mm = 305 mm 1 OF 2 M
BOBTAIL - NO TRANSMISSON 1" = 1'

FORMAT B SIZE
838
[33.0]
MINIMUM ENGINE SPACING

150 95
[5.91 ] [3.74 ]

8 8 ENGINE OIL FILL CAP


FRONT ENGINE LIFTING [.32 ] [.32 ]

ALTERNATOR

OIL LEVER GAGE

COOLANT FILL CAP


289.6
[11.40 ]

BACK OF BLOCK

23.8
[.94 ]

REAR ENGINE LIFTING

416.3 170.1
[16.39] [6.70 ]
FFOB

RFOB

LENGTH OF BLOCK AIR FILTER


PRIMING PUMP

OIL/AIR SEPARATOR
FUEL INLET

POWER STEERING/GEAR OIL COOLER INLET

FUEL FILTER

400
77.5 [15.7 ]
[3.05 ] AUX. HEATER SUPPLY
POWER STEERING/GEAR OIL COOLER OUTLET

CRANKSHAFT

8.7
[.34 ]

n 31.5 [1.24]
SEAWATER INLET 17.9
[.70 ]

STARTER MOTOR 710


THROTTLE CABLE CONNECTION [27.95]

BLOCK GROUND (-)


BATTERY (+)

* VIEWS ARE WITH ENGINE COVER REMOVED


NOTES:
(1) REFER TO THE APPLICATION MANUAL FOR COMPLETE PRODUCT INSTALLATION REQUIREMENTS.
(2) DIMENSIONS REQUIRE A MINIMUM OF 1/2 in. (13 mm) CLEARANCE FOR MOTOR MOUNT DEFLECTION.
(3) INNER AND OUTER SURFACES OF TRANSOM MUST BE PARALLEL WITHIN 1/8 in. (3 mm) IN AREA COVERED BY TRANSOM
PLATES AND REMAIN WITHIN TRANSOM THICKNESS LIMITS.
(4) REFER TO "TRANSOM CUTOUT" IN THE INSTALLATION MANUAL TO FIND THE CRANKSHAFT CENTERLINE VS. BOAT BOTTOM.

REVISION UNITS SCALE SHEETS


8M4503637
2.0L TIER3 - VGT A
mm
(in)
1:12
25.4 mm = 305 mm 2 OF 2 M
BOBTAIL - NO TRANSMISSON 1" = 1'

FORMAT B SIZE

You might also like