Scribd Logo
Upload

Welcome to Scribd!

  • 23 views

    Ic 695 Alg 808

    Uploaded by

    Zaki noui
    The document provides information about the GE Fanuc IC695ALG808 isolated analog output module. The module has 8 configurable voltage or current output channels and connects to a PACSystems RX3i CPU. It requires an external 24VDC power supply and the channels can be individually configured and monitored.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Ic 695 Alg 808

    Uploaded by

    Zaki noui
    23 views5 pages
    The document provides information about the GE Fanuc IC695ALG808 isolated analog output module. The module has 8 configurable voltage or current output channels and connects to a PACSystems RX3i CPU. It requires an external 24VDC power supply and the channels can be individually configured and monitored.

    Original Title

    ic695alg808

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides information about the GE Fanuc IC695ALG808 isolated analog output module. The module has 8 configurable voltage or current output channels and connects to a PACSystems RX3i CPU. It requires an external 24VDC power supply and the channels can be individually configured and monitored.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    23 views5 pages

    Ic 695 Alg 808

    Uploaded by

    Zaki noui
    The document provides information about the GE Fanuc IC695ALG808 isolated analog output module. The module has 8 configurable voltage or current output channels and connects to a PACSystems RX3i CPU. It requires an external 24VDC power supply and the channels can be individually configured and monitored.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    GE Fanuc IC695ALG808

    http://www.pdfsupply.com/automation/ge-fanuc/rx3i-pacsystem/IC695ALG808

    Rx3i PacSystem

    Isolated Analog Output module, 8 channels, that is configurable IC695A


    IC695AL IC695ALG

    919-535-3180
    [email protected]
    PACSystems™ RX3i
    GFK-2481 Isolated Analog Output Module, IC695ALG808
    November 2007

    Isolated Analog Voltage/Current Output module IC695ALG808 provides


    MODULE OK eight configurable voltage or current output channels. Analog channels can
    FIELD STATUS be configured for these output ranges:
    TB ▪ Current: 0 to 20mA, 4 to 20mA

    ▪ Voltage: +/- 10V, 0 to 10V


    IC695ALG808
    The module must be located in an RX3i Universal Backplane. It requires an
    RX3i CPU with firmware version 5.0 or later. Machine Edition Version 5.7
    Q1
    SP3 Logic Developer-PLC or later must be used for configuration.

    These modules can be used with a Box-style (IC694TBB032), Extended


    Q2
    Box-style (IC694TBB132), Spring-style (IC694TBS032), or Extended
    Spring-style (IC694TBS132) Terminal Block. Extended terminal blocks
    Q3
    provide the extra shroud depth needed for shielded wiring. See the
    PACSystems RX3i System Manual, GFK-2314 revision B or later for more
    Q4 information about Terminal Blocks. Terminal Blocks are ordered separately.

    Isolated +24 VDC Power


    Q5
    The module must receive 24 VDC field power from an external source. The
    external source must be connected directly to the module’s terminal block. It
    Q6
    cannot be connected via the TB1 connector on the RX3i Universal
    Backplane.
    Q7
    Module Features

    Q8 ▪ Completely software-configurable, no module jumpers to set


    ▪ Individually enable or disable channels
    ▪ Clamping and Alarm Limits
    ▪ Latching of Alarms
    ▪ Configurable output bias
    ▪ Rapid channel acquisition times based on filter frequency
    ▪ On-board error-checking
    ▪ Configurable scaling and offsets per channel
    ▪ High alarm, low alarm, high-high alarm, low-low alarm detection and
    reporting selectable per channel
    ▪ Module fault reporting
    ▪ Configurable Hold Last State or Output Defaults
    2 RX3i Isolated Analog Output Module

    GFK-2481

    Specifications
    Output Ranges Current: 0 to 20mA, 4 to 20mA
    Voltage: +/- 10V, 0 to 10V
    Backplane Power Requirements 80mA maximum at 3.3V
    Power Dissipation within 7.25 Watts maximum (Vuser=24V)
    Module
    Thermal Derating See derating curves later in this document
    External +Power Supply Voltage Range: 19.2V to 30V (24V nominal)
    Current: 600mA maximum
    Resolution +/-10V: 15.9 bits, 0 to 10V: 14.9 bits, 0 to 20mA: 15.9 bits,
    4 to 20mA : 15.6 bits
    Output Data Format Configurable as floating point IEEE 32 bit or 16-bit integer in a 32-bit field
    Analog Update Rate 8 milliseconds (approximate, all eight channels)
    (Determined by I/O scan time,
    application dependent)
    Output Overvoltage Protection Current outputs only: -30V for 60 seconds, +30V for one hour
    Calibrated Accuracy Accurate to within 0.15% of full scale at 25°C
    Accurate to within 0. 25% of full scale at 60°C
    In the presence of severe RF interference (IC 801-3, 10V/M), accuracy may
    be degraded to +/-1% FS.
    Output Load Reactance Current: 10µH maximum, Voltage: 1µF maximum
    Maximmum Output Load Current: 1350 Ohms maximum
    Voltage: 2 Kohms minimum
    Output Gain Drift Voltage output: 20ppm per degree C typical
    Current output: 35ppm per degree C typical
    Output Settling Time Voltage or current output: 2ms, 0 to 95%
    Isolation, Field to Backplane 2550VDC for one second

    Output Points vs. Temperature, Current Mode


    Thermal deratings for module IC695ALG808 are shown below.
    RX3i Isolated Analog Output Module 3
    GFK-2481

    Release History
    Firmware
    Version Upgrade Kit
    Revision
    IC695ALG808-AA 1.00 None: Initial Release

    LEDs
    The Module OK LED indicates module status. The Field Status LED indicates whether the external +24
    VDC power supply is present and is above the minimum level and whether or not faults are present. All
    LEDs are powered from the backplane power bus.

    LED Indicates
    Module OK ON Green: Module OK and configured.
    Quick Flashing Green: Module performing powerup sequence.
    Slow Flashing Green or Amber: Module OK but not configured.
    OFF: Module is defective or no backplane power present
    Field Status ON Green No faults on any enabled channel, Terminal Block is present, and field
    power is present.
    ON Amber and TB Green: Terminal Block is installed, fault on at least one
    channel, or field power is not present.
    ON Amber and TB Red: Terminal Block not fully removed, field power still
    detected.
    OFF and TB Red: Terminal block not present and no field power is detected.
    TB ON Red: Terminal block not present or not fully seated. See above.
    ON Green: Terminal block is present. See above.
    OFF: No backplane power to module.
    4 RX3i Isolated Analog Output Module

    GFK-2481

    Field Wiring
    The table below lists wiring connections for the Isolated Analog Output Modules. There are no shield
    terminals.
    Terminal Assignment Assignment Terminal
    1 No Connect No Connect 19
    2 Channel 1 Voltage/Current Output Channel 5 Voltage/Current Output 20
    3 Channel 1 Ground/Return Channel 5 Ground/Return 21
    4 No Connect No Connect 22
    5 No Connect No Connect 23
    6 Channel 2 Voltage/Current Output Channel 6 Voltage/Current Output 24
    7 Channel 2 Ground/Return Channel 6 Ground/Return 25
    8 No Connect No Connect 26
    9 No Connect No Connect 27
    10 Channel 3 Voltage/Current Output Channel 7 Voltage/Current Output 28
    11 Channel 3 Ground/Return Channel 7 Ground/Return 29
    12 No Connect No Connect 30
    13 No Connect No Connect 31
    14 Channel 4 Voltage/Current Output Channel 8 Voltage/Current Output 32
    15 Channel 4 Ground/Return Channel 8 Ground/Return 33
    16 No Connect No Connect 34
    17 External + Power Supply (+24V In) No Connect 35
    18 External - Power Supply (+24V Rtn) No Connect 36
    Each channel can be individually configured to operate as a voltage output or a current output - not both
    simultaneously.

    Current
    Voltage
    No Connect 1 Output 19 No Connect
    Output
    Channel 1 Output 2 + + 20 Channel 5 Output
    V I
    Channel 1 Return 3 _ _ 21 Channel 5 Return
    No Connect 4 22 No Connect

    5 23
    6 24
    . .
    17
    24VDC
    + .
    .
    18 - 36

    There are no shield terminals on these modules. For shielding, tie cable shields to the ground bar along the
    bottom of the backplane. M3 tapped holes are provided in the ground bar for this purpose.

    For technical assistance, please go to www.gefanuc.com/support

    All rights reserved. PACSystems is a Trademark of GE Fanuc Intelligent Platforms, Inc.

    You might also like