Service Manual: ATV 500-D

2014 ATV
SERVICE MANUAL EUROPE 14.0

PN. F010102A14
● ATV 500-D
493cc
Cette revue concerne les modèles suivants :

HY510S - HY500 60ème - HY500T - HY510IS - HY500IS - HY540ST - HY540STL
WARNING
The parts of different types/ variants/ versions maybe un-interchangeable, even some parts
have almost same appearance. Always refer to Parts Manual of each ATV model for spare
parts information and service.
※General Information
※Maintenance
※Engine
※Chassis
※Final Drive
※Transmission
※Brakes
※Electrical
ATV SERVICE MANUAL EUROPE 14.0
PN. F010102A14
LH500ATV-D 维修手册欧标英文版本 14.0 零件代号 F010102A14

Foreword
This manual is designed primarily for use by the ATV factory certified service technicians in
a properly equipped shop. Persons using this manual should have a sound knowledge of
mechanical theory, tool use, and shop procedures in order to perform the work safely and
correctly. The technician should read the text and be familiar with service procedures
before starting the work. Certain procedures require the use of special tools. Use only the
proper tools, as specified. Cleanliness of parts and tools as well as the work area is of
primary importance.
This manual is divided into sections. Each section covers a specific ATV component or
system and, in addition to the standard service procedures. Keep this manual available for
reference in the shop area. When using this manual as a guide, the technician should use
discretion as to how much disassembly is needed to correct any given condition.
All references to left and right side of the vehicle are from the operator's perspective when
seated in a normal riding position.
At the time of publication all information contained in this manual was technically correct.
Some photographs used in this manual are used for clarity purposes only and are not
designed to depict actual conditions. We constantly refine and improve its products, all
materials and specifications are subject to change without notice.
This ATV’s publications and decals display the words Warning, Caution, Note, and At This
Point to emphasize important information:
WARNING
Indicates a potential hazard which will result in severe injury or death to the operator,
bystander or person inspecting or servicing the ATV..
CAUTION
Indicates a potential hazard which may result in personal injury or death or damage to the
machine.
NOTE
The word “NOTE” in this manual will alert you to key information or instructions.
CONTENTS
CHAPTER1 ………………………………………………General Information↖
CHAPTER2 ………………………………………….……………Maintenance↖
CHAPTER3……………………………………. …. ………………500 Engine↖
CHAPTER4…………………………………………..…………………Chassis↖
CHAPTER5………………………………………………….………Final Drive↖
CHAPTER6………………………………………………………………Brakes↖
CHAPTER7………………………………………………….….………Electrical↖
WARNING
Never run an engine in an enclosed area. Carbon monoxide exhaust gas is
poisonous and can cause severe injury or death. Always start engines outdoors.
Gasoline is extremely flammable and explosive under certain conditions. Battery
electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with
skin, eyes or clothing. Always keep alert and wear protection..
Exhaust system components are very hot during and after use of ATV. Never service
when the engine is warm or hot. Escaping steam from cooling system or hot oil from the
machine can cause severe burns. The engine must be cool before service.
Crate of the ATV and parts in the ATV maybe have sharp edge, always pay attention
and wear protection.
CHAPTER 1 GENERALINFORMATION LH500ATV-D SERVICE MANUAL 14.0
CHAPTER 1 GENERAL INFORMATION
WARNING
The parts of different types/ variants/ versions maybe un-interchangeable, even some parts have
almost same appearance. Always refer to Parts Manual of each ATV model for spare parts
information and service.
1.1 IMPORTANT INFORMATION
1.2 V.I.N AND ENGINE SERIAL NUMBER
1.3 VEHICLE DIMENSIONS
CHAPTER 1 GENERAL PAGE. 1- 1

1.1 IMPORTANT INFORMATION
PREPARATION FOR REMOVAL PROCEDURES

1. Remove all dirt, mud, dust and foreign material before removal and disassembly.
2. Use proper tools and cleaning equipment.
3. When disassembling the machine, always keep mated parts together. This includes gears,
cylinders, pistons and other parts that have been ”mated ”through normal wear. Mated part must
always be reused or replaced as an assembly.
4. During machine disassembly, clean all parts and place them in trays in the order of disassembly.
This will speed up assembly and allow for the correct installation of all parts.
5. Keep all parts away from any source of fire.
REPLACEMENT PARTS
Use only genuine parts for all replacements. Use recommended oil and grease for all lubrication
jobs. Other brands may be similar in function and appearance, but inferior in quality.
GASKETS,OIL SEALS AND O-RINGS

1. Replace all gaskets seals and O-rings when overhauling the engine. All gasket surfaces, oil seal
lips and O-rings must be cleaned.
2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips.
LOCK WASHERS/PLATES AND COTTER PINS
Replace all lock washers/plates and cotter pins

after removal. Bend lock tabs along the bolt or
nut flats after the bolt or nut has been tightened
to specification.
BEARINGS AND OIL SEALS

Install bearings and oil seals so that the
manufacturer’s marks or numbers are visible.
When installing oil seals, apply a light coating of
lightweight lithium base grease to the seal lips.
Oil bearings liberally when installing, if
appropriate.
oil seal
CAUTION:
Do not use compressed air to spin the bearings
dry. This will damage the bearing surfaces.
Bearing

CIRCLIPS
1. Check all circlips carefully before reassembly.
Always replace piston pin clips after one use.
Replace distorted circlips. When installing a
circlip① , make sure that the sharp-edged
corner ② is positioned opposite the thrust
③ it receives. See sectional view.
④Shaft
CHECKING OF CONNECTIONS
Dealing with stains, rust, moisture, etc. on the
connector.
1. Disconnect:
zConnector
2. Dry each terminal with an air blower.
3. Connect and disconnect the connector two or
three.
4. Pull the lead to check that it will not come off.
5. If the terminal comes off, bend up the pin ①
and reinset the terminal into the connector.
6. Connect:
z Connector
NOTE:
The two connectors ” click ” together.
7. Check for continuity with a tester.

NOTE:
z If there is no continuity, clean the terminals.
z Be sure to perform the steps 1 to 7 listed
above when checking the wire harness.
z Use the tester on the connector as shown.
WARNING
Never run an engine in an enclosed area. Carbon monoxide exhaust gas is poisonous and
can cause severe injury or death. Always start engines outdoors.
Gasoline is extremely flammable and explosive under certain conditions. Battery electrolyte is
poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing.
Always keep alert and wear protection..
Exhaust system components are very hot during and after use of ATV. Never service when
the engine is warm or hot. Escaping steam from cooling system or hot oil from the machine can
cause severe burns. The engine must be cool before service.
Crate of the ATV and parts in the ATV maybe have sharp edge, always pay attention and wear
protection.

CONVERSION TABLE
How to use the CONVERSION TABLE
Use this table to convert METRIC unit data to IMPERIAL unit data.
Ex.
METRIC MULIPLIER IMP
**mm x 0. 3937 = **in
**cm x 0.03937 = **in
CONVERSION TABLE
METRIC TO IMP
Known Multiplier Result
Torque m·kg 7.233 ft·lb
86.794
m·kg 0.0723 In·lb
cm·kg 0.8679 ft·lb
cm·kg In·lb
Weight kg 2.205 lb
g 0.03527 oz
Distance km/h 0.6214 mph
km 0.6214 mi
m 3.281 ft
m 1.094 yd
cm 0.3927 in
mm 0.03927 in
Volume/ cc(cm3) 0.03527 oz(IMP liq.)
Capacity cc(cm3) 0.06102 cu·in
lit(liter) 0.8799
qt (IMP liq.)
lit(liter) 0.2199
gal(IMP liq.)
Miscellaneous kg/mm 55.997 lb/in
kg/cm2 14.2234 psi(lb/in2 )
Centigrade 9/5(℃)+32 Fahrenheit(°F)

1.2 V.I.N AND ENGINE SERIAL NUMBER


1.3 VEHICLE DIMENSIONS

Note.
The on-road equipments (rear view mirror, turn lights, etc.) are not Standard Equipment for USA.
ATV 500

NOTES

CHAPTER 2 MAINTENANCE LH500ATV-D SERVICE MANUA 14.0
CHAPTER 2 MAINTENANCE
WARNING
have almost same appearance. Always refer to Parts Manual of each ATV model for spare parts
2.1 PERIODIC MAINTENANCE
2.2 FUEL SYSTEM
2.3 TOE ALIGNMENT
2.4 BRAKING SYSTEM INSPECTION
2.5 SUSPENSION SPRING RPELOAD ADJUSTMENT
2.6 WHEELS
2.7 TIRE PRESSURE
2.8 FRAME, NUTS, BOLTS, FASTENERS
CHAPTER 2 MAINTENANCE PAGE. 2- 1

2.1 PERIODIC MAINTENANCE

GENARAL
CAUTION
Mark on the following chart
DL ：Due to the nature of the adjustments marked with a DL on the following chart, it is
recommended that service be performed by an authorized dealer.
▲： Service/Inspect more frequently when operating in adverse conditions.
PERIODIC MAINTENANCE SCHEDULE

Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition.
Inspection, adjustment and lubrication intervals of important components are explained in the
following chart on the following pages.
Maintenance intervals are based upon average riding conditions and an average vehicle
speed of approximately 16km/h (10 miles per hour). Vehicles subjected to severe use, such
as operation in wet or dusty areas, should be inspected and serviced more frequently.
Inspect, clean, lubricate, adjust or replace parts as necessary.
NOTE: Inspection may reveal the need for replacement parts. Always use genuine parts
available from your dealer.
Service and adjustments are critical. If you are not familiar with safe service and adjustment
procedures, have a qualified dealer perform these operations.
A = Adjust I = Inspect
C = Clean L = Lubricate
D = Drain R = Replace
T =Tighten to Correct Torque
Item Hours When Remarks

Service (Main) Brake / Pre-ride I
System
Auxiliary (Secondary) Brake / Pre-ride I
Parking Brake / Pre-ride I
Tires / Pre-ride I
Wheels / Pre-ride I
Frame nuts, bolts fasteners / Pre-ride I
Air Filter-Pre-Cleaner / Daily I C
▲
Coolant/Level / Daily I
Coolant 150 Annually R

Coolant strength 25 hrs 3 months I Inspect strength seasonally
▲ Air Box Sediment Tube / Daily D
Headlamp Inspection / Daily C

apply dielectric grease to connector when
replaced
Tail lamp inspection / Daily C
apply dielectric grease to socket when
replaced
▲ Air Filter-Main Element 2 Weekly I C
Replace if necessary
▲ Transmission Oil Level 10 Monthly I
change annually
Battery Terminals 10 Monthly I C
Battery fluid level 10 Monthly I
DL Brake pad wear 2 Weekly I
▲ Gear case Oil 10 Monthly C

150 annually R
Engine Cylinder Head and 25 3 months I
Cylinder Base Fasteners (re-torque required at first service only)
▲ General Lubrication 25 3 months L
all fittings, pivots, cables,
etc.
Engine Oil-Level / Daily I
Engine Oil Change 30 hrs 3 months R
Break-in Service at 1 month. Change oil more
often in cold weather use.
▲ Oil Filter 50 hrs 6 months I C
▲ Engine breather hose 100 hrs 6 months I
Carburetor Float Bowl 50 hrs 6 months Drain bowl periodically and prior to storage
Throttle Cable / Pre-ride I
DL Throttle Cable 50 hrs 6 months A L (Grease M) R if necessary
Shift linkage 50 hrs 6 months I A R if necessary
DL Transmission belt 50 hrs 6 months I

R if necessary
▲ Steering 50 hrs 6 months I L T if necessary
▲ Rear Axle ( and Bearings) 50 hrs 6 months I L

▲ Front Suspension 50 hrs 6 months I L

T if necessary
▲ Rear Suspension 50 hrs 6 months I
T if necessary
Spark Plug 100 hrs 12 months I
R if necessary
DL Ignition Timing 100 hrs 12 months I
Adjust as needed
DL Fuel System 100 hrs 12 months Check for leaks at tank, cap, lines, fuel valve,
filter, and carburetor. Replace lines every 2
years.
DL Fuel Filter 100 hrs 12 months R
Radiator 100 hrs 12 months I R
Cooling System hoses 50 hrs 6 months I

R if necessary
Spark arrestor 10 hrs monthly C
R if necessary
DL Clutches (drive and Driven) 25 hrs 3 months I R
R if necessary
Engine mounts 25 hrs 3 months I T
DL Valve clearance 100 hrs 12 months I A
DL Shift selector box 200 hrs 24 months Change grease every two years
(H/L/R/N)
DL Brake fluid Level / Pre-ride I
Brake fluid 200 hrs 24 months Change every two years
Idle Speed / As A
Required
DL Toe adjustment / As Periodic inspection, adjust when parts are
Required replaced
Headlight Aim / As Adjust if necessary
Required
▲ Front drive chain (and 300 hrs (full time in I, Replace if necessary
DL sprockets) in transmission 4X4), or 1000 hrs ( in

(only SDX300 ); 2X4 alternate 4X4 )
▲ Ball joint (A arm- strut) 10 hrs monthly I, (for damage, wear, and play)
DL R. Replace if necessary

LUBRICANT AND FLUID

Item Lube Rec Method Frequency
1. Engine Oil SAE 15W/40 SE Add to proper Check level daily
level on dipstick
2. Brake Fluid DOT 3 Only Maintain level As require; change
Between fill lines. See every two years or 200
“7.CONTROL” hours
3. Transmission Oil SEA 80W/90GL5 Add to proper Change annually or at
level on dipstick 100 hours
4.Rear Gear case oil SEA 80W/90GL5 Add to proper Change annually or
level at 100 hours
5. Front Gear case SEA 80W/90GL5 Add to proper Change annually or
oil ( SDX30-0 ) level at 100 hours
▲ 6. Front A-arm Grease Locate fitting on pivot shaft Every 3 months or 50
pivot Shaft and grease with grease gun hours
( Except
Maintenance-Free
A-arm pivot )
▲ 7.Steering Grease Locate fitting on Every 3 months or 50
Post Bushings pivot shaft and hours
grease with grease gun
▲ 8.Front Wheel Grease Inspect and replace bearings if Semi-annually
bearings (high temperature necessary
resist)
9.Tie rods Grease Locate fittings and grease Semi-annually
10.Shift Grease Locate fittings and grease Semi-annually
Linkages
▲ 11.Ball joints Inspect Inspect and replace it if Semi-annually
necessary
▲ 12.Rear Axle Grease Locate fittings and grease Every 3 months or 50
Bearing hours
▲ 13.Swing Arm Grease Locate fittings and grease Monthly or 20 hours
Bearing
▲ 14.Throttle Grease M Grease, inspect and replace it Monthly or 20 hours
Cable if necessary
15. Rear prop shaft Grease Locate fittings and grease Every 3 months or 50
U-joint hours
16. Rear prop shaft Grease Locate fittings and grease Every 3 months or 50
yoke hours
17. Front prop shaft Grease Locate fittings and grease Every 3 months or 50
U-joint ( SDX300) hours
18. Front prop shaft Grease Locate fittings and grease Every 3 months or 50
yoke ( SDX300) hours
19. Inner and outer Grease M Grease, inspect and replace it Every 3 months or 50
CV-Joints (SDX300) if necessary hours
▲
21. A-arm pivot Grease Locate fittings and grease Every 3 months or 50
hours
shaft

LUBRICATION RECOMMENDATIONS
NOTE:
1. More often under severe use, such as wet or dusty conditions.
2. Grease: Light weight lithium-soap grease.
3. Grease M：Molybdenum disulfide (MoS2 ) grease (water resistant).
4. When suspension action becomes stiff or after washing.
5. Hours are based on 10 mph(16Km/h) average.

2.2 FUEL SYSTEM
WARNING
Gasoline is extremely flammable and explosive under certain conditions.
Always stop the engine and refuel outdoors or in a well ventilated area.
Do not smoke or allow open flames or sparks in or near the area where refueling is
performed or where gasoline is stored.
Do not overfill the tank. Do not fill the tank neck.
If you get gasoline in your eyes or if you swallow gasoline, see your doctor immediately.
If you spill gasoline on your skin or clothing, immediately wash it off with soap and water
and change clothing.
Never start the engine or let it run in an enclosed area. Gasoline powered engine exhaust
fumes are poisonous and can cause loss of consciousness and death in a short time.
Never drain the float bowl when the engine is hot. Severe burns may result.

ATV 500
FUEL LINES FUEL FILTER

Check fuel lines for signs of wear, The fuel filter should be replaced in
deterioration, damage or leakage. Replace if accordance with the Periodic Maintenance
Chart or whenever sediment is visible in the
necessary.
filter.
Be sure fuel lines are routed properly and 1. Shut off fuel supply at fuel valve.
secured with cable ties. 2. Remove line clamps at both ends of the
CAUTION: Make sure lines are not kinked or filter.
pinched. 3. Remove fuel lines from filter.
Replace all fuel lines every two years. 4. Install new filter and clamps onto fuel lines
with arrow pointed in direction of fuel flow.
5. Install clamps on fuel line.
6. Turn fuel valve ON. ATV 500

7. Start engine and inspect for leaks.
8. Reinstall fuel tank.
ATV 500
FUEL VALVE AND STRAINER SCREEN routed properly toward the ground and
FOR B-TYPE ATV500 secured with cable ties. CAUTION: Make
sure lines are not kinked or pinched
NOTE *NOTE. On some models, there is a
After installing the fuel valve and connecting Roll-Over Valve on the end of the gas tank
the fuel line, refill the fuel tank and turn the vent line. Make sure the ↑ mark on the
fuel valve ON and check that there is no fuel
R-O Valve is upwards.
leaking.
WARNING
Always pay attention to the fittings of the
plastic gas tank during fuel lines service.
Don’t pull the line from the tank directly for
removal. Inspect fittings and tank body for
looseness, nicks, and scratches. Replace
gas tank if necessary.
VENT LINES AND ROLL OVER VALVE*

1. Check fuel tank, oil tank, carburetor,
battery, and transmission vent lines for
signs of wear, deterioration, damage or
leakage. Replace every two years.
2. Be sure vent lines and drain lines are
2.3 TOE ALIGNMENT

METHOD: STRAIGHTEDGE OR STRING
Be sure to keep handlebars centered
NOTE: String should just touch side surface

of rear tire on each side of the ATV.
Measure from string to rim at front and rear of
rim.
Rear rim measurement (A) should be 1/16" to
1/8" (1.5 to 3 mm) more than front rim
measurement (B).
NOTE: The steering post arm (frog) can be
used as an indicator of whether the
handlebars are straight. The frog should
always point straight back from the steering
post when handlebars are straight.
WARNING: Always pay attention to tie rods

assembly, Both ends must screw in same and
enough threads length.

2.4 BRAKING SYSTEM

INSPECTION
The following checks are recommended to

keep the braking system in good operating
condition. Service life of braking system
components depends on operating conditions.
Inspect brakes in accordance with the
maintenance schedule and before each ride.
zKeep fluid level in the master cylinder
reservoir to the indicated level on reservoir.
zUse DOT 3 brake fluid.
NOTE: Use new brake fluid or brake fluid

from a sealed container to avoid
contamination to system.
zCheck brake system for fluid leaks.

zCheck brake for excessive travel or spongy
feel.
zCheck friction pads for wear, damage and
looseness.
zCheck surface condition of the disc.
BRAKE PAD INSPECTION

zPads should be changed when friction
material is worn to 3/64" (1mm).
HOSE/FITTING INSPECTION
Check braking system hoses and fittings for
cracks, deterioration, abrasion, and leaks. Foot control brake is only for ATV 260 / 300
Tighten any loose fittings and replace any
worn or damaged parts.
FOOT BRAKE ADJUSTMENT Adjusting brake pedal for B-Type

NOTE If the push rod joint is reinstalled, adjust the
On European ATV 260 / 300 and B-type , foot push rod length so that the distance between
brake is the SERVICE brake (MAIN brake) the centers of the master cylinder lower
Use the following procedure to inspect the mounting bolt hole and joint pin hole is
hydraulic foot brake system and adjust or 80±1mm.After adjustment, tighten the joint
bleed if necessary. nut.

1. First check foot brake effectiveness by

applying a 25 kg (50 lb). (Approx)
downward force on the pedal.
The top of the pedal should be at least 1
inch, (25 .4m m) above the surface of the
footrest. CONTROLS
If less than one inch, two things must be Check controls for proper operation,
examined: positioning and adjustment.
Free Play: Brake control and switch must be positioned
Free play of the brake pedal should be to allow brake level to travel throughout entire
1/8-1/4 inch (3-6mm). range without contacting switch body.
If free play is excessive, inspect pedal,
linkage, and master cylinder for wear or
damage and replace any worn parts.
Bleeding:
If free play is correct and brake pedal travel is
still excessive, air may be trapped some
where in the system. Bleed the hydraulic
brake system in a conventional manner,
following the procedure outlined in the Brake
chapter.
FOOT BRAKE TESTING

The foot brake should be checked for
proper adjustment.
Support the rear wheels off the ground. While
turning the rear wheels by hand, apply the
auxiliary footbrake. This brake should not Note: burnishing procedure is also applicable
stop the wheels from turning until the lever is for parking brake. See CHAPTER 7
half way between its rest position and BRAKES.
bottoming on the footrest.
MECHANICS PARKING BRAKE FOR

EUROPE ATV 500
Checking
Although the parking brake has been
adjusted at the factory, the brake should be
checked for proper operation. The
mechanical brake must be maintained to be
full functional.

1. With the engine off, apply the parking

brake lever and attempt to move the ATV.
2. If the rear wheels are locked, it is adjusted
properly.
3. If the wheels are not locked, it must be
adjusted.
1. With the engine off, loosen the adjustor on
To
the adjust
lever. (set up) the mechanical parking
brake,
2. Loosenusethe
thejam
following procedure
nut of the adjuster on the
caliper.
3. Turn the adjuster (bolt) CW (clockwise) by
hand till the pad touch the brake disc, turn the
adjuster bolt CCW (counterclockwise) by 1/4
to one turn for 10 to 20mm free play at the
end of the parking lever. ↑ adjust on the lever ATV500
4. Tighten the jam nuts securely against the
adjusters.
5. Make sure the rear wheels turns freely
without dragging.
6. Turn the adjustor (the one on the lever) Adjusting can also be done to the brake cable
and apply the lever. While adjusting, it is on the parking lever side by turn the adjuster
important you apply the lever back and forth (nut) directly.
for operation, free play and the locking of the
parking position.
7. Make sure the rear wheels turns freely
without dragging and parking brake works
properly.
CAUTION Don’t over tighten the adjustor.
Free play of the lever: 20mm.
8. Field test for parking. It must be capable of
holding the laden ATV stationary on an 18%
up and down gradient.
↑adjust on the lever
↑ adjust on the caliper ATV 500
Note: The adjusting on the caliper is for the

wear out of the pads.
A temporary adjusting can also be done to

the brake cable on the parking lever side by
turn the adjuster (nut) directly. But the adjust
range is limited. Always do the procedure 1
to 8 when necessary.
adjuster jam nuts.

NOTE: Apply the front brake a number of
times to ensure the wheels lock and the
brake light illuminate properly.
4. Make sure the right and left brake are
balance after the adjustment of the front
brakes by test at low speed. Contact your
dealer for proper diagnosis and repairs.
5. If adjusting the cables does not attain
proper brake performance and free-play, the
brake shoes must be replaced.
Note: After the adjusting, the adjustment
distance of the cables and the angle of the
↑ adjust on the caliper B-type ATV drum levers between the right and left brake
must be same.
2. If the both front wheels are locked, it is

adjusted properly.
3. If the wheels or one wheel are/is not locked,
it must be adjusted.
Adjusting
To adjust (set up) the mechanical drum brake,
use the following procedure.
1. Loosen the jam nuts of the
adjuster on the right hand of
right and left brake cable.
2. Turn the both adjusters keep the rock arm
on the lever balance until 1/8” (2to3mm) free
play is achieved at the brake lever.
rake shoes as a set either is worn to the limit.
NOTE: While adjusting free play, it is

important you apply the lever back and forth.
3. Tighten the jam nuts securely against the
adjusters.
If the right hand adjustment is inadequate
to attain the proper brake free-play gap, make
adjustment at the middle of the cables
2.5 SUSPENSION SPRING RPELOAD ADJUSTMENT

Operator weight and vehicle loading affect
suspension spring preload requirements. Adjust
as necessary.
FRONT SUSPENSION
Compress and release front suspension.
Damping should be smooth throughout the
range of travel.
Check all front suspension components for
wear or damage.
Inspect from strut cartridges for leakage.
Shock spring preload can not be adjusted,
replace if necessary.
REAR SUSPENSION
Compress and release rear suspension.
Damping should be smooth throughout the
range of travel. Check all rear suspension
components for wear or damage.
Inspect shock for leakage
Shock spring preload can be adjusted using

the shock spanner wrench.

2.6 WHEELS
Inspect all wheels for runout of damage.
Check wheel nuts and ensure they are tight.
Do not over tighten the wheel nuts.
WHEEL, HUB TORQUE TABLE
Item
ATV500
Front Wheel Nuts 69 Ft.Lbs 96 N.m
Rear Wheel Nuts 69 Ft.Lbs 96 N.m
Front Spindle Nut Refer to FRONT HUB
INSTALLATION
Rear Hub
Retaining Nut 80 Ft.Lbs 110.6 N.m
WHEEL REMOVAL
1. Stop the engine, place the transmission in
gear
And lock the parking brake.
2. Loosen the wheel nuts slightly.
3. Elevate the side of the vehicle by placing
a suitable stand under the footrest frame.
4. Remove the wheel nuts and remove the
wheel.
WHEEL INSTALLATION
1. With the transmission in gear and the ATV500
parking Brake locked, place the wheel in
the correct Position on the wheel hub. Be
sure the valve stem is toward the outside
and rotation arrows on the tire point
toward rotation.
2. Attach the wheel nuts and finger tighten
them.
Install as shown at right for front or rear
wheels.
3. Lower the vehicle to the ground.
4. Securely tighten the wheel nuts to the
proper Torque listed in the table above.
On rear wheel nuts, Make sure tapered
end of nut goes into taper on wheel.
CAUTION:
If wheels are improperly installed it could
affect Vehicle handling and tire wear.

2.7 TIRE PRESSURE

TIRE INSPECTION
CAUTION :
Tire Pressure Inspection
z Maintain proper tire pressure. Refer to the
warning tire pressure decal applied to the Front Rear
vehicle.
zImproper tire inflation may affect ATV
maneuverability. 500
zWhen replacing a tire always use original 14PSI 14PSI
equipment size and type and replace in (96±0.5KPa) (96 ±0.5KPa)
pairs, especially in SDX300 model.
z The use of non- standard size or type tires
may affect ATV handling and cause
machine damage, especially in SDX300 WARNING Operating an ATV with worn tires
model. will increase the possibility of the vehicle
TIRE TREAD DEPTH skidding easily with possible loss of control.
Always replace tires when tread depth is Worn tires can cause an accident.
worn to 1/8" (3mm ) or less. Always replace tires when the tread depth
measures 1/8" (3mm ) or less.

2.8 FRAME , NUTS, BOLTS, FASTENERS

Periodically inspect the tightness of all fasteners in accordance with the maintenance schedule.
Check that all cotter pins are in place. Refer to specific fastener torques listed in each chapter.
ATV 500
Item Torque（Ft-Lb） Torque (Nm) Remarks
12 Only ATV 260
EARLY DESIGN* Handlebar Clamp Nut M6 16
early model
Handlebar Clamp Nut M8 18 25
Nut M10X1.25 Attaching Tie Rod to Steering column 26-30 35-41
Nut M10X1.25 Attaching Tie Rod to Front Absorber Strut body 26-30 35-41
Tie Rod Jam Nut M12 13 17
MANTENANCE-FREE PIVOT DESIGN Bolt M12 Attaching 37-44
50-60 LT*
A-Arm and Frame
Nut M10X1.25 Attaching A-Arm to Ball Joint Stud 22-25 30-35
Screw M6 Attaching Ball Joint Mounting Bracket to Front 8
11 LT*
Absorber Strut body (MacPherson)
Swing Arm Pivot Left 14 19 Refer to SWING
Swing Arm Pivot Right 120 165 ARM
120 ASSEMBLY
INSTALLATION
，4.2 SWING
Threaded Pivot Nut (for swing arm) 165
ARM，
CHAPTER 4A
CHASSIS
Nut M14X1.5 Attaching Front Absorber to Frame 15-18
21-25 LT*
(MacPherson)
Nut M8 Binding Front Absorber and Front Absorber Strut body 15
21 LT*
(MacPherson)
18
Bolt M8 Attaching Front Caliper to Front Absorber Strut body 25 LT*
Bolt M8 Attaching Upper Steering Clamp to Frame 12 16
12
Nut M8 Attaching Lower Steering Bearing Retainer to Frame 16
20
Nut M10X1.25 Attaching Front Wheel to Front Wheel Hub 27
Front （Drive） Axle Nut Refer to FRONT HUB INSTALLATION

18
Screw M8 Attaching Front Brake Disc to Front Wheel Hub 25 LT*
22-25
Nut M10X1.25 Attaching Rear Brake Disc to Rear Brake 30-35 LT*
Rear Axle Nut M20X2 (for swing arm) 80 110.6
Rear Hub Retaining Nut M20X1 （for IRS） 101 137
Nut M10X1.25 Attaching Rear Caliper to Axle Tube 18 25 LT*
Bolt M12x30 Attaching Axle Tube and Swing arm to Rear 60
80
Gear-box
Bolt M12x35 Attaching Axle Tube to Swing arm 60-66 80-90
LT*---Apply Loctite™ 242

NOTES

CHAPTER 3 ENGINE LH500ATV-D SERVICE MANUAL14.0
CHAPTER 3 ENGINE
500 cc
3.1 Removal and Installation of Engine, Drive Train and Gearshift Unit
3.1.1 Overhaul Info
3.1.2 Engine Removal and Installation
3.1.3 R e m o v a l a n d I n s ta l l a t i o n o f F r o n t a n d R e a r A x l e
3.1.4 Removal and Installation of Gearshift Unit
3.2 Troubleshooting
3.3 Engine Overhaul Information
3.4 Checks & Adjustment
3.5 Engine Removal, Inspection & Installation
3.6 Carburetor
3.7 Cooling and Lubrication System
3.8 Troubleshooting
CHAPTER 3 ENGINE PAGE. 3- 1

3.1. Removal and Installation of Engine, Drive Train and Gearshift Unit
Overhaul Info…..……………………………..3.1.1 Removal and Installation of Front and Rear

Axle……………………………………………….3.1.3
Engine Removal and Installation…………...3.1.2 Removal and Installation of Gearshift Unit……3.1.4
3.1.1 Overhaul info
Operation cautions
●Securely support the ATV with bracket when removing or installing engine.
Take care not to damage frame, engine body, bolts and cables.
●Wrap the frame to avoid any possible damage when removing or installing the engine.
●Following operation doesn’t require removal of engine from the vehicle:
—Oil pump
—Carburetor, air filter
—Cylinder head cover, cylinder head, cylinder body, camshaft
—CVT system, CVT cover
—Gearbox
—Right side cover, AC magneto, water pump
—Piston, piston ring, piston pin
●Following operation require removal of engine from vehicle:
—Crankshaft
●Tightening torque:
Engine front upper mounting bolt: 35～45N·m
Engine front rear mounting bolt: 40～50N·m
Bolt, engine front rear mounting bracket 35～45N·m

●Engine Removal
Remove:
--Plastic(→Chapter 2)
--Air Filter(→Engine service chapter)
--Carburetor (→Engine service chapter)
--Clamp
--Water Inlet Hose
Remove screw
Remove gear shift rod
Remove clamp
Remove water outlet hose
Remove Sleeve.
Remove connectors of magneto, enriching device lead,
pickup, water temperature transducer, gear sensor as
illustrated on the right.

Remove spark plug cap from cylinder.
Remove protection sleeve of starter relay.
Remove Nut.
Disconnect positive wire of starter relay.
Remove nut.
Remove negative wire of starter relay.
Remove Bolt 1 and Nut 1 of upper engine hanger.

Remove Bolt 1 and Nut 1 of lower engine hanger.
Remove Bolt 2 and Nut 2 of lower engine hanger.

3.1.2 Engine Installation

Put engine onto the frame，install the two lower mounting bolts and nuts.
Then install the upper and lower engine hangers.
Tightening torque: Engine upper hanger bolt:35～45N.m

Engine lower hanger bolt:50～60N.m
Install:
--Water outlet and inlet hoses to engine with proper clamps.
--Positive and negative starting wires to engine.
--Connect all the connectors.
--Spark plug cap.
--Gearshift rod to engine.
--Air filter, carburetor and removed parts.
3.1.3 Removal and Installation of Front and Rear Axle
Support the vehicle with jack, make sure the vehicle will not fall.
Remove:
--Plastic parts for frame(→Chapter 2)
--Front and rear wheels and arms(→Chapter 6)
--Air filter(→engine service chapter)
--Carburetor(→engine service chapter)
--Engine
--Rear brake caliper(→7-4)
1. Nut 2. Bolt 1 3. Bolt 2 4. Front Axle 5. Bolt 3 6. Front Drive Shaft

7. Clamp 8. Breather Hose, Front Axle 9. Bolt 4 10. Rear Axle
11. Breather Hose, Rear Axle
12. Rear Brake Disk 13. Bolt 5 14. Rear Drive Shaft

Remove nut and bolt of front axle from frame.
Remove nut and bolt of rear axle from frame.
.
Remove the 18 bolts for drive shafts

and front and rear axles.
(Refer to P. 5-5, Bolt 3 of Part No.5)
Remove:
--Front and rear axles, drive shafts, rear brake disc
Installation:
Reverse the removal procedure for installation.
Tightening torque:
Bolt, front axle：40-50N.m
Bolt, rear axle：40-50N.m
Bolt, front and rear drive shafts：40-50N.m
Gearshift Unit
Remove:
--Left and right side panel
--Fuel tank top cover
--Front fender
--Bolt
--Gearshift rod
Remove the 2 bolts
Remove gearshift unit
Installation:
Make sure that gearshift is flexible.
In case of any inflexibility, adjust the gearshift rod to

ensure the gear engagement.

3.2. Troubleshooting
Operation Notice……………………………………………………………………..3.2.1
Starting Failure/Hard Starting……………………………………………………….3.2.1
Unstable Engine Running or Engine Stops……………………………………..…3.2.2
Poor Engine Performance in High-speed Range or Slow Speed Rising……….3.2.3
Unstable Idle Speed…………………………………………………………………3.2.4
Poor Engine Performance in Middle or High Range………..……………………3.2.5
Operating Notice
This chapter is a general explanation of major troubleshooting of the whole engine.
Refer to the relevant chapters for troubleshooting not listed in this chapter.
Starting Failure/Hard Starting
In case of starting failure or hard starting, refer to chapter of starting system (Engine maintenance
notebook) for troubleshooting and check the starting system whether have problems or not.
Loosen drain screw, check if fuel No Fuel No fuel in fuel tank

has reached carburetor Clogged fuel hose
Clogged float valve
Reached Clogged fuel filter
Clogged fuel tank cap breather hole
Remove spark plug and mount it Weak spark or Faulty spark plug
to spark plug cap, get it earthed No spark Stained or damaged spark plug
and check spark
Normal spark Faulty high tension coil or short circuit

Faulty Ignition coil or short circuit
Faulty ignition switch
Faulty CDI unit
Faulty pickup coil
Measure compression pressure Low or no Faulty cylinder head (Engine Service)
Compression Worn or damaged Cylinder and piston
ring
Faulty cylinder gasket
Normal compression pressure
Try starting as operation Nearly start, but Deteriorated fuel

starting failure Improper idle speed adjustment
Secondary air intake into air intake pipe
Engine cannot be started Improper ignition time
Clogged air filter
Remove spark plug and check Wet spark plug Carburetor overflow
again Excessive opening of throttle
Clogged air filter
Dry spark plug
Remove carburetor over 30

minutes, connect ethylene pipes No Air current
with fuel increment loop and blow Faulty fuel enrichment device

Unstable Engine Running or Engine Stops

Loosen drain screw, and check No petrol in fuel tank
the if fuel has reached carburetor No fuel Clogged fuel hose
Clogged float valve
With Fuel Clogged fuel filter
Remove spark plug Stained, damaged and color changed

and check it Stained or damaged spark plug
Improper spark plug heat value
Normal Spark Plug
Remove spark plug and mount it Weak spark or Faulty spark plug or stained spark plug
to spark plug cap, get it earthed No spark Faulty Ignition coil
and check spark Faulty high tension coil or short circuit
Normal Spark Faulty pickup coil
Faulty CDI unit
Measure compression pressure Low or no Worn Cylinder and piston ring

with pressure meter compression Faulty cylinder gasket
pressure
Check ignition timing Incorrect Faulty pickup coil

Faulty CDI unit
Correct
Check caburetor Improper adjustment Refer to Engine Service

mixture screw
Correct adjustment
Check if there is
secondary air into Air intake Faulty tightening of carburetor joint
carburetor joint
No secondary air
Remove fuel enrichment No continuity Broken cable of fuel enrichment device

device wire lead and Faulty fuel enrichment device
check continuity
Normal Continuity

Connect fuel enrichment

device wire lead with
battery for 5 Minutes. With Air current
Connect ethylene pipe Faulty fuel enrichment device
with fuel increment loop
and blow.
No air current
Clogged carburetor
Poor Engine Performance in Hi-speed Range or Slow Speed Rising
Run vehicle at high engine speed No rise of Clogged air filter

(on an flat asphalt road) Engine speed Clogged fuel hose and filter
Clogged muffler
Engine speed rises
Check ignition timing Incorrect Faulty pickup coil

Faulty CDI unit
Correct
Measure compression pressure Low or no Worn Cylinder and piston ring

with pressure meter Compression
Pressure Faulty cylinder gasket
Check carburetor Clogged

Clogged carburetor
Not clogged
Check spark plug Stained damage and color changed

Spark plug stained and damaged
Improper spark plug heat value
Normal Spark Plug
Check the engine for Overheated Faulty mixture gas

overheating Faulty fuel
Carbon deposit in combustion Chamber
Too much advanced ignition timing
Overheated
Accelerate or continuous
Cylinder knock Carbon deposit in combustion chamber
high-speed operation
No cylinder knock
Clutch slip

Unstable Idle Speed

check ignition Timing Incorrect Faulty pulse generator
Faulty CDI unit
Correct
check carburetor Incorrect

mixture screw Refer to fuel system (Engine Service)
Correct
Check if secondary air Air intake Faulty tightening of carburetor joint

intake into carburetor Faulty reed valve seal washer
joint
No Air intake
Remove spark plug and mount it Weak spark or Stained or damaged spark plug
to spark plug cap, get it earthed No spark Faulty Ignition coil
and check spark Faulty high tension coil or short circuit
Normal spark Faulty CDI unit
Remove fuel enrichment device No Continuity Broken cable of fuel enrichment device
wire lead and check continuity Faulty fuel enrichment device
Normal Continuity

and blow.
No air current
Clogged carburetor

Poor Engine Performance in Middle or High Range
check ignition timing Correct Faulty pulse generator

Faulty CDI unit
Correct
check carburetor Clogged

Clean
Normal
Remove fuel enrichment device No continuity Broken starting enriching cable

wire lead and check continuity Faulty fuel enrichment device
Normal continuity

and blow.
Not air current

3.3．Engine Overhaul Information

Item Conversion
2
Press
1kgf/cm =98.0665KPa 1KPa=1000Pa
1mmHg=133.322Pa=0.133322KPa
Torque 1kgf.m=9.80665N.m
Conversion Table
3
Volume 1ml=1cm =1cc
3
1l=1000 cm
Warning/Caution/Note
Please read this manual and follow is instructions carefully. To emphasize special information, the symbol and
the words WARNING,CAUTION and NOTE have special meanings. Pay attention to the messages highlighted
by these signal words.
Warning:
Indicates a potential hazard that could result in injury or death.
Caution:
indicates a potential hazard that could be result in vehicle damage.
Note:
provides key information to make procedures easier or instruction clearer.
Please note, however, that the warnings and cautions contained in this manual can’t possibly cover all the
potential dangerous information to the servicing, or lack of the vehicle. Except WARNINGS and CAUTIONS
stated in this manual, mechanic should have a basic understanding of the mechanical ideas and the procedure
of machine repair. If mechanic can’t master all the troubleshooting operation, please consult with qualified
mechanic for advice.

General Precautions ………………………………..…………………………..3.3.2

Fuel, Oil and Coolant……………………………………………………………3.3.3
Brake-in ………………………………………………………………………….. 3.3.3
Engine Exterior and Engine No…………………………………………………3.3.4
Engine Specification………………………………………………..……………3.3.5
Overhaul Data……………………………………………………………………. 3.3.6
Tightening Torque Table………………………………………………………….. 3.3.10
Tools……………………………………………………………………………….. 3.3.12
Materials for Operation and Fixing ……………….……………………….……. 3.3.14
.
.

GENERAL PRECAUTIONS
Warning ! Proper service and repair procedures are important for the safety of
operator and the safety and reliability of the vehicle.
When two or more persons work together, keep reminding each other for safety purpose.
When start the engine indoors, make sure that the exhaust gas is forced outdoors.
If use hazardous or flammable material, please strictly operate according to manufacturer’s operation
manual. Operate in a well- ventilated place.
Never use gasoline as a cleaning solvent.
Do not touch the engine oil, radiator or muffler with bare hands to avoid scalding before it is cooled.
Check all the lines, and fittings related to the system for leakages, after repairing fuel, cooling, lubricating
or exhaust system .
Do not dispose used oil, coolant or defective parts optionally for environmental purpose.
CAUTION:
Use genuine CFMOTO parts or their equivalent.

Place and store the disassembled parts separately in order for correct assemble.
Use special tools according to service manual.
Make sure that all parts used in reassembly are clean, lubricated them when specified.
Use the special lubricants, sealants and greases.
Pre-tighten the bolts, nuts and screws, then tighten according to the specified torque, from big to small and
from inner side to outer side.
Fix torque screw with torque wrench, clean grease or oil from the screw thread before fixing.
Check the parts after disassembling, clean the parts before measuring.
Check parts for tightness and proper operation, after assembling.
Replace the disassembled washers, o-rings, seals, locknuts, lockwashers, cotter pins, circlips with new
ones.

FUEL, OIL, COOLANT

Fuel
Use unleaded gasoline with octane number over 90.
OIL
Use a premium quality 4-stroke motor oil to ensure
longer service life of your vehicle. Use only oils that
meet API service classifications SF or SG and that
have a viscosity rating of SAE10W/40. If oil with a
rating of SAE 10W/40 is not available, select an
alternative according to the chart.
ENGINE COOLANT
Since antifreeze also has corrosion and rust-inhibiting properties, always use coolant containing antifreeze,
even if the atmospheric temperature does not go below the freezing point.
It is suggested that the freezing point of antifreeze should be 5℃ lower than the lowest ambient temperature
where the vehicle is used.
Recommended Coolant: -35℃ antifreeze, corrosion-resistant, high boiling point coolant
Warning! Coolant is poisonous. Never drink it. Store it properly.
Caution: DO NOT mix coolant with that of other engines.
BREAK-IN PROCEDURES
During manufacturing only the best possible material are used and all machined parts are finished to a very
high standard. It is still necessary to allow the moving parts to “BREAK-IN” before subjecting the engine to
maximum stresses. The future performance and reliability of the engine depends on the care and restraint
exercised during its early life. Refer to the following break-in engine speed recommendations.
For better performance and durability, a new engine requires a run-in time of 20 hours as under:
0~10 Hours:
Avoid continuous operation above half throttle. Allow a cooling off period of five to ten minutes after every hour
of operation. Vary the speed of vehicle from time to time. Do not operate it at one set throttle position.
10~20 Hours
Avoid prolonged operation above 3/4 throttles. Rev the vehicle freely but do not use full throttle at any time.
Note: Keep the daily maintenance during the run-in time and eliminate the troubles, if any. After 20h run-in time,
do the maintenance according to the owner’s manual for normal operation of the ATV.

Engine Exterior and Engine No

Engine Specification
REF. ITEM Type/SPECIFICATION
NO
1 Type Single Cylinder, 4-Storke, Liquid-cooled,
4 Valve, SOHC
2 Bore and stroke 87.5mm×82.0mm
3 Displacement 493ml
4 Compression ratio 10.2: 1
5 Lowest continuous idle speed with load 1400r/min±100r/min
6 Starting type Electrical starting/ Recoil Starting
Ignition / CDI Magneto ignition/BTDC10°1500r/min

Ignition Timing
7 Electrical
Spark Plug/ DPR7EA-9 (NGK)/0.8mm-0.9mm
System Spark Plug Gap
Magneto Permanent Magnet AC Type
Combustion Chamber Triangle Combustion Chamber
Combustion
8 Carburetion Type/Model Vacuum Diaphragm Type/MIKUNI BSR36-129
System
Air Filter Sponge Element Filter
Gasoline RQ-90
9 Valve Valve Type SOHC/Chain Drive

System
Lubrication Type Pressure & Splash
10 Lubrication Oil Pump Rotor Type

System Filter Type Full Flow Filter Screen
Oil Type SAE15W-40/SF
Cooling Type Closed Coolant Circulation

11 Cooling
System Coolant Type —35℃ Rust-resistant antifreeze
Clutch type Wet, Auto-centrifugal

Operation Mode Automatic(CVT)+Parking and Gear Shifting
Gears 2 Forward Gears + 1 Reverse Gear
Shift Type/Sequence Hand Operation/L-H-N-R
Drive (CVT) Gear Ratio 2.88-0.70
12
Final Ratio 1.333(24/18, bevel gear)
System
Transfer Secondary 1.952(41/21)
Ratio
Gear Ratio Gears Low Gear:2.25(36/16) High Gear :1.35(27/20)
Reverse Gear:1.471(25/17)
Total Low Gear:5.857, High Gear:3.514,Reverse Gear:3.828

13 Overall Dimension 610×568×519mm
14 Net Weight 70kg
15 Output type Front and rear shaft output
16 Rotational Direction of Engine Output Clockwise (from behind engine at forward gear)

Overhaul Data
Item Standard Service Limit Remark

Valve Head Diameter IN 30.6
-----------
EX 27.0
IN 0.05-0.10
Valve Clearance ------------
EX 0.010-0.037
Clearance Between Valve IN 0.010-0.037
------------
Guide and Valve Stem EX 0.030-0.057
Inner Diameter of Valve
IN & EX 5.000-5.012 -------------
Guide
IN 4.975-4.990 -------------
Outer Diameter of Valve Stem
EX 4.955-4.970 -------------
Valve Stem Play IN & EX ------------- 0.05
Length of Valve Stem End IN & EX 2.9-3.1 2.3
Valve Head Thickness IN & EX ------------- 0.5
Play of Valve Head Seal IN & EX ------------ 0.03
Width of Valve Seat Seal IN & EX 0.9-1.1 -------------
Valve Spring Free Length IN & EX 40 38.8
182-210N,(when
Valve Spring Tension IN & EX compressed to --------------
31.5mm)
IN 33.430-33.490 33.130
Cam Height
EX 33.500-33.560 33.200
Clearance Between Φ22 0.032-0.066 0.150
Camshaft Outer Diameter & Φ17.5 0.028-0.059
0.150
Hole
Φ22 21.959-21.980 ---------------
Camshaft Outer Diameter
Φ17.5 17.466-17.484 ---------------
Inner Diameter of Camshaft Φ22 22.012-22.025 ----------------
Hole Φ17.5 17.512-17.525 ----------------
Camshaft Play 0.10
Inner Diameter of Rocker Arm IN & EX 12.000-12.018 ----------------
Outer Diameter of Rocker
IN & EX 11.973-11.984 ----------------
Arm
Cylinder Head Distortion 0.03 0.05
Cylinder Head Cover
0.03 0.05
Distortion

Cylinder + Piston + Piston Ring + Connecting Rod

Cylinder Pressure 1000KPa ------------
Cylinder-Piston Clearance 0.030-0.051 0.15
Piston Skirt Diameter 87.460-87.480 87.380
(10mm form skirt end)
Inner Diameter of Cylinder 87.500-87.522 ------------
Cylinder Joint Face Distortion 0.015 0.05
Top R About 11.7 8.9
Piston Ring Free Gap Ring
2ND R About 12 9.5
Ring
Piston Ring Gap In Bore Top Ring 0.15-0.30 0.60
2ND Ring 0.15-0.30 0.60
Piston Ring Groove Top Ring 0.04-0.08 0.180
Clearance 2ND Ring 0.03-0.07 0.150
Top Ring 0.97-0.99 -------------
Piston Ring Thickness
2ND Ring 1.17-1.19 -------------
Top Ring 1.03-1.05 -------------
Piston Ring Groove Width 2ND Ring 1.22-1.24 -------------
Oil Ring 2.51-2.53
Inner Diameter of Piston Pin 23.002-23.008 23.030
Hole
Outer Diameter of Piston Pin 22.995-23.000 22.980
Inner Diameter of Connecting 23.006-23.014 23.040
Rod Small End
Clearance of Connecting Rod 0.10-0.55 1.0
Big End
Thickness of Connecting Rod 24.95-25.00
Big End
Crankshaft Play 0.03 0.08
Lubrication
Clearance between Inner 0.03mm-0.10mm 0.15mm
and Outer Rotors
Clearance between Outer 0.03mm-0.10mm 0.12mm
Rotor and Oil Pump Body
Oil Pressure 130Kpa-170Kpa ( 3000r/min) ---------
Oil Type SAE10W-40, API SF or SG ---------
When changing 1900ml ----------
Oil Capacity When Replacing 2000ml ----------
Filter
Engine Repair 2200ml ---------

Clutch + Transfer

Clutch Plate Inner diameter 140.00-140.15 140.50
Clutch Engagement Speed 1800-2400r/min ---------
Clutch Lock Speed 3300-3900r/min ---------
Drive Belt Width 35.2 33.5
Free length of Secondary 168 160
Sheave Spring
Shift Fork to Groove
0.10-0.40 0.50
Clearance
Thickness of Left Shift Fork 5.8-5.9 ------------
Thickness of Right Shift Fork 5.8-5.9 ------------
Shift Fork Groove Width 6.0-6.2 ------------
Drive Output Gear Groove
6.0-6.2 ------------
Width
Cooling System

Thermostat Valve Opening
68-74℃ ----------
Temperature
Thermostat Valve Lift 4.5-6.5mm ( at 80℃) ----------
Radiator Cap Opening
110-140Kpa ----------
Pressure
Water
Resistance (Ω) ----------
Corresponding Relation Temperature (℃)
Between Water-temperature 50 154+16
Transducer’ resistance and 80 52+4
water-temperature 100 27+3
120 16+2
Functioning Temperature of OFF--ON 88 ℃ ------------
Thermoswitch ON--OFF 82℃ ------------
Coolant Type -35℃ antifreeze, corrosion-resistant, high
------------
boiling point coolant

Carburetor
Item Standard Remark

Carburetor Type MIKUNI BSR36-129
I.D. Mark 07G0
Carburetor Barrel Size 36mm
Engine Idle Speed 1400r/min+100r/min
Main Jet (MJ) N10221-137.5#
Main Air Jet (MAJ) MD13/24-35#
Jet Needle (JN) J8-5DH77
Needle Jet (NJ) 785-401011-P-OM
Pilot Jet (PJ) N224103-22.5#
Pilot Jet Screw (PS) 604-16013-1A
Electrical System
Item Standard Remark

Spark Plug Type NGK;DPR7EA-9
Gap 0.8-0.9
Spark Character >8mm
Ignition coil Primary 0.1Ω-0.5Ω
Resistance
Secondary 12Ω-22Ω
Magneto Coil Pick-up 150Ω-300Ω
Resistance
Magneto Voltage (Without load) >100V(AC),5000r/min
Max. Magneto Output Power 300W, 5000r/min
Regulated Voltage 13.5V-15.0V, 5000r/min
Primary Peak Voltage of Ignition Coil >150W
Starter Relay Coil Resistance >120W
Starter Relay Coil Resistance 3Ω-5Ω
Auxiliary Starter Relay Coil Resistance 90-100Ω

Tightening Torques
Item Quantities Thread Size (mm) Tightening Torque Remark

(N.m)
Reverse Gear Sensor 1 M10*1.25 20
Spark Plug 1 M12*1.25 18
Water-temperature
1 Rc1/8 8 Apply Thread Locker
Sensor
Adjusting Nut,
4 M5 10
Valve Clearance
Nut, Primary Sheave 1 M20*1.5 115
Nut, Secondary
1 M20*1.5 115
Sheave
Ring Nut, Secondary
1 M30*1 100
Sheave
Nut, Front Drive Shaft 1 M14*1.5 97
Nut, Drive Bevel Gear 1 M22*1 145
Nut, Driven Bevel
1 M16*1.5 150
Gear
Fixing Nut, Clutch 1 M18*1.5 70 Counter Clockwise
Limit Nut, Drive Bevel
1 M60 110 Apply Thread Locker
Gear Bearing
Nut, Universal Joint Counter Clockwise,
1 M55 80
Yoke Apply Thread Locker
Bolt, Rocker Arm
2 M14*1.25 40
Shaft
Oil Drain Bolt 1 M12*1.5 30
Bolt, Overriding
6 M8 26 Apply Thread Locker
Clutch
Bolt, Magneto Stator 3 M6 10 Apply Thread Locker
Screw, CVT Plate 3 M6 10 Apply Thread Locker
Bolt, Oil Pipe 2 M14*1.5 40
Bolt, Oil Pump 3 M6 10
Bolt, Pressure
2 M6 10
Release Valve
Bolt, Drive Bevel
4 M8 32
Gear Cover
Bolt, Driven Bevel
4 M8 25
Gear Cover
Bolt, Gear Limit 1 M14×1.5 18
Bolt, Splined Spacer 1 M10×1.25 60

Tightening Torques
Item Quantiti Thread Size Tightening Torque Remark

es (mm) (N.m)
Bolt, Crankcase 14 M6 10
3 M8 25
Bolt, Driven Sector Gear 1 M6 12
Bolt, Oil Filter 1 M20×1.5 36
Bolt, Oil Starter Motor 2 M6 10
Bolt, Cylinder Head 4 M10 42
Bolt, Cylinder Head 2 M6 10
1 M8 25
Bolt, Cylinder (Upper &
4 M6 10
Lower)
Bolt, Cylinder Head
12 M6 10
Cover
Bolt, Chain Tensioner 2 M6 10
Bolt, Chain Tensioner 1 M8 20
Bolt, Fan Motor 3 M6 10
Bolt, Thermostat
2 M6 10
Housing
Bolt, Water Pump Cover 3 M6 10
Bolt, Water Pump 2 M6 10
Fixing Bolt, Timing Apply Thread Locker
2 M6 15
Chain
Other Bolts M5 4.5-6
M6 8-12
M8 18-25

Maintenance Tools
Measurement Tools
No. Description Specification Purpose
1 Vernier Caliper 0-150mm For measuring the length and thickness
2 Micrometer 0-25mm For measuring outer diameters of rocker arm, valve stem
and camshaft
3 Micrometer 25-50mm For measuring the max. lift of camshaft
4 Micrometer 75-100mm For measuring piston skirt
5 Cylinder Gauge For measuring cylinder bore diameter
6 Small Bore Gauge 10-34mm Fore measuring inner gauge of rocker arm, piston pin bore,
connecting rod small end bore
7 Dial Indicator 1/100 For measuring the play
8 Straightedge Gauge Plane measuring
9 Feeler Gauge Plane and valve clearance measuring
10 Fuel Level Gauge For measuring the carburetor fuel level
11 Thickness Gauge For measuring the clearance
12 Spring Balance For measuring the spring tension
13 Tachometer For measuring engine speed
14 Oil Pressure Gauge For measuring oil pressure
15 Compression Gauge & For measuring cylinder compression
Adapter
16 Radiator Cap Tester For measuring radiator cap opening pressure
17 Ohmmeter For measuring resistance and voltage
18 Ammeter For measuring current/switches
19 Thermometer For measuring liquid temperature
20 Timing Light For checking the ignition timing
21 Torque Wrench For measuring the tightening torque
General-purpose and Auxiliary Tools
22 Alcohol Burner Heating up
23 Magnetic Stand For micrometer
24 Slab Auxiliary tool for measuring
25 V-block For measuring the play
26 Tweezer For installation of valve cotter
27 Circlip Pliers For removal and installation of circlips
28 Long Nose Pliers For removal and installation of retainers
29 Impact Driver For removal of cross-headed bolts
30 (-) Driver
31 (+) Driver

Special Tools
No. Description Specifications Purpose

1 Spark Plug Wrench Removal and installation of spark plug
2 Clutch Holder For removing/installing clutch carrier nuts
3 Oil Filter Wrench Removal and installation of oil filter cartridge
4 Piston Pin Puller For removal of piston pin
5 Flywheel Puller For removal of magneto rotor
6 Crankcase Separating Tool For separation of left and right crankcase
7 Crankshaft Remover For removal of crankshaft from left crankcase
8 Crankshaft Installation Set For installing crankshaft to left crankshaft
9 Valve Spring Compressor For removal and installation of valve spring
10 Valve Seat Cutter For valve-seating
11 Ring Nut Wrench Removal/installation of CVT secondary sheave
12 Sheave Holder Removal/installation of CVT secondary sheave
13 Sheave Spring Compressor Removal/installation of CVT secondary sheave
14 Couple Gear/Middle Shaft
Removal/installation of the coupling gear nut
Tool
15 Bearing Driver Set For installation of bearing and oil seal
16 Bearing Removing Tool Set For removal of bearing
17 Oil Seal Removing Tool For removal of oil seal
18 Universal Joint Holder For removal/installation of the universal joint yoke nut

Materials for Operation and Fixing
Materials for engine operation engine oil, grease and coolant. Fixing materials include sealant, thread locker,
etc.
Description Type Application Area Remark

capacity
SAE10W-30 Cylinder bore 1900ml
Lubricating or SAE15W-40 Crankcase (for changing oil)
or SAE20W-50 Refer to Engine Lubrication 2000ml
Oil/Engine Oil
API service classifications System (→14-14) (for replacing filet)
SF or SG 2200ml
(for engine repairing)
Molybdenum piston pin、valve stem、valve
lubrication oil oil seal、camshaft
Oil seal lip, O-ring and
#3 MoS2 Lithium Base sealing faces of other
Lubricating Grease
rubber seal materials,
Grease
bearings with seals, CVT
bearing and collar
-35℃ antifreeze, Cooling system、Water-seal Capacity according to
Coolant corrosion-resistant, high radiator and water hose
boiling point coolant system
Joint face of crankcase,
Joint Face Sealant crankcase and cylinder,
cylinder head and cover
Thread Locker Thread Parts See 3.3.10, 3.3.11

3.4. Checks & Adjustment
Periodic Maintenance ……………………………………………………….3.4.2
Procedures of Maintenance and Adjustment…………….……………….. 3.4.3
Valve Clearance……………………………………………………………... 3.4.3
Engine Idle Speed…………………………………………….…….……….. 3.4.4
Spark Plug………………………………………………………...…….……. 3.4.4
Air Filter……………………………………………………………………….. 3.4.5
Fuel Hose, Carburetor………………………………………………………..3.4.6
Drive Belt……………………………………………………...………………. 3.4.7
Inspection of Lubrication System……………………………………..…….. 3.4.8
Inspection of Cooling System……………………………………………….. 3.4.10
Inspection of Cylinder Pressure………………………………………..……3.4.11
Inspection of Oil Pressure………………………………………………...…. 3.4.12
Inspection of Clutch Engagement and Lock-up……………………..…….. 3.4.13

Periodic Maintenance Table

The table below lists the recommended intervals for all the required periodic maintenance work necessary to
keep the vehicle at its best performance and economy. Maintenance intervals are expressed in terms of
kilometer, miles and hours, whichever occurs first.
Note: More frequent maintenance may be required on vehicles that are used in severe conditions.
Interval Km Initial 200 Every 1000 Every 2000 Remark

Miles Initial 100 Every 600 Every 1200
Item Hours Initial 20 Every 40 Every 80
Valve Clearance IN: 0.05~0.10
I -- I
EX:0.15~0.20
Idle Speed I I I 1400±100r/Min
Spark Plug -- -- I No carbon deposit
Replace every 6000Km Gap: 0.8~0.9mm
Air Filter -- C C Replace every 2000Km
Fuel Hose, Carburetor -- -- I Replace every 4 years
Clutch -- -- I
Drive Belt -- I R
Engine Oil R -- R
Oil Filter R -- R
Coolant Level I I I
Water Hose & Pipes I I I
Coolant Replace every 2 years
I=Inpection and adjust, or replace if necessary
R=Replace
C=Clean

Procedures of Maintenance & Adjustment
This section describes the maintenance procedures for

each item mentioned in the Periodic Maintenance Chart.
VALVE CLEARANCE
Inspect initially at 20-hour break-in and every 40 hours

or every 1000km thereafter. Inspect the clearance after
removing cylinder head.
Excessive valve clearance results in valve noise and

insufficient valve clearance results in valve damage and
reduced power.
Check the valve clearance at the period indicated above
and adjust the valve clearance to specification, if
necessary.
Remove cover ①
Remove inspection cap ②on left crankcase.
Remove 2 valve adjusting cover ③
Turn the crankshaft until the line④ of T.D.C. on rotor is
aligned with mark⑤ of inspection hole on left
crankcase.
Insert feeler gauge to check the clearance between
the valve stem end and the adjust bolt on the rocker
arm.
Valve Clearance (When cold)

IN: 0.05-0.10mm EX: 0.15-0.20mm
Note:
The valve clearance must be adjusted when the
engine is cold.
Adjust the valve clearance when the piston is at the
Top Dead Center (T.D.C.) on the compression stroke.
If the clearance is incorrect, bring it into the specified range

using the special tool.
Loosen valve adjust bolt and nut, insert a feeler gauge

between the valve stem end and valve adjusting bolt,
tighten valve adjust bolt, make sure it slightly contacts the
feeler gauge, tighten bolt and nut.

Take out the feeler gauge, measure the clearance.

If the clearance is incorrect, repeat the above steps until
the proper clearance is obtained.
Locknut: 10 N.m
Caution:
Securely tighten the locknut after completing
adjustment
Install:
2 valve adjusting cover;
Inspection cap;
Recoil starter;
Cover plate;
Apply a small quantity of THREAD LOCKER to recoil
starter fixing bolts.
Tools:
Valve adjuster
Feeler gauge
Material:
Thread Locker
ENGINE IDLE SPEED

Inspect initially at 20 hours run-in and every 40
hours or 1000km thereafter.
Start the engine and warm it up for several minutes,

measure engine speed with a tachometer. Set the
engine idle speed between 1300~1500 r/min by turning
the throttle stop screw of carburetor.
Engine idle speed: 1400r/min±100r/min
Note:
Make this adjustment when the engine is hot
Tool: Tachometer
SPARK PLUG
Inspect initially at 20 hours run-in and every 80 hours or
2000km thereafter. Replace every 6000km.
Remove the spark plug with a special tool
Specification: DER7EA-9(NGK)
If the electrode is extremely worn or burnt, or spark plug

has a broken insulator, damaged thread, etc, replace the
spark plug with a new one.

In case of carbon deposit, clean with a proper tool.

SPARK PLUG GAP
Measure the spark plug gap with a feeler gauge.
Out of specification: → Adjust
Spark plug gap: 0.8-0.9mm
Caution:
Check the thread size and reach when replacing the
spark plug. If the reach is too short, carbon will be
deposited on the screw portion of the spark plug hole and
engine damage may result.
Installation:
Caution:
To avoid damaging the cylinder head threads; first,
tighten the spark plug with fingers, and then tighten it to
the specified torque using the spark plug wrench.
Tightening Torque: 18 N.m

Tool: Spark Plug Wrench, Feeler Gauge
Air Filter
Inspect every 40 hours or 1000 km, clean it if
necessary.
If the air cleaner is clogged with dust, intake resistance

will be increased, with a resultant decrease in power
output and an increase in fuel consumption. Check and
clean the air filter as following:
Remove fixing clamp① and top cover②
Note:
Be careful not to drop the o-ring into the air filter box that
is attached to the air filter top cover.
Loosen screw③, remove filter element④, separate
support⑤, filter element⑥ and filter element seat⑦.
Fill a wash pan of a proper size with a
non-flammable cleaning solvent A. Immerse the
filter element in cleaning solvent and wash it.
Press the filter element between the palms of both
hands to remove the excess solvent. Do not twist or
wring the element or it will tear.
Immerse the element in engine oil B, and then
squeeze out the excess oil leaving the element
slightly wet.

A--Non-flammable cleaning solvent

B—Engine oil SAE#30 or SAE10W/40.
Warning:
Never use with gasoline or low flash point solvents to
clean the filter element
Inspect the filter element for tears. torn element must be

replaced.
Note:
If driving under dusty conditions, clean the air filter element
more frequently. The surest way to accelerate engine wear
is to operate the engine without the element or with torn
element. Make sure that the air filter element is in good
condition at all times.
Remove the drain plug⑧ of air box to drain out any
water.
Fuel Hose
Inspect every 80 hours or 2000 km, replace every 4
years.
Inspect the fuel hose for damage and fuel leakage. If any
damages are found, replace the fuel hose with a new
one.
Drive Belt
Removal:
Remove CVT cover
Hold the primary sheave with special tool and loosen

primary sheave nut.
Special Tool: Rotor Holder
Remove primary sliding sheave 1;

Hold the secondary sheave with special tool and loosen
secondary sheave nut. Remove secondary sheave
together with drive belt.
Special Tool: Rotor Holder
Remove drive belt from secondary sheave

Inspection:
Inspect drive belt for wear and damage. If any cracks or

damages are found, replace drive belt with a new one.
Inspect drive belt for width, if width is out of service limit,

replace drive belt with a new one.
Service Limit: 33.5mm
Tool: Vernier Caliper
Installation
Reverse the removal procedure for installation. Pay
attention to the following:
Insert drive belt, as low as possible, between secondary
sliding sheave and primary fixed sheave.
Hold secondary sheave with a special tool and tighten
the nut to the specified torque.
Nut, Secondary Sheave: 115 N.m
Install primary sheave and nut. Hold the primary sheave

with a special tool and tighten the nut to the specified
torque.
Nut, Primary Sheave:115N.m
Turn primary sheave, until the drive belt is properly

seated and both the primary and secondary sheaves
rotate together smoothly and without slipping.
Caution:
Fit the drive belt with the arrow on the drive belt
points toward normal turning direction.
The drive belt contact surface of the driven face
should be thoroughly cleaned.
Install CVT cover

Inspection of Lubrication System
Replace engine oil and oil filter initially at 20

hours or 200km and every 80 hours or 2000km
thereafter.
Check Engine Oil Level

Keep the engine in a plan position.
Remove oil dip rod 1
Clean oil dip rod, insert oil dip rod but do not tighten
it.
Take out oil dip rod and check if oil is between upper
and lower limit.
If the engine oil is insufficient, fill more oil until the
sufficient oil is obtained.
Engine Oil: SAE15W/40 classification SF or SG
Note:
Keep the engine in a plan position
Do not tighten oil dip rod when measuring oil
level
Replacing Engine Oil

Remove oil dip rod 2, drain bolt 2
and washer 3.
Drain out the engine oil while the engine is still
warm.
Clean oil dip rod, drain bolt and washer with solvent.
Install washer and drain bolt.
Drain Bolt: 30 N.m
Fill engine oil. ( about 1900ml)

Install oil dip rod, start the engine and allow it to run
for several minutes at idling speed.
Turn off the engine and wait for about 3 minutes,
and then check the oil level on the dipstick.
Caution:
The engine oil should be changed when the engine is
warm. If the oil filter should be replaced, replace engine
oil at the same time.
Replacing Oil Filter
Remove relative parts ( see Replacing Engine Oil)

Remove oil filter① with the special tool
Install washer and drain bolt
Install new oil filter with the special tool
Fill engine oil (about 2000ml) and check (see
Replacing Engine Oil)
Tool: Oil Filter Wrench
Engine Oil Capacity

When replacing oil: 1.9L
When replacing oil filer: 2.0 L
Engine overhaul:2.2 L

Inspection of Cooling System
Check initially at 40 hours or 1000km, replace

coolant every 2 years.
Check radiator, reservoir tank and water hoses.
Leakage or Damage: → Replace
Check coolant level by observing the upper and the
lower limit on the reservoir tank.
If the level is below lower limit, fill coolant until the level
reaches the upper limit.
Replacing Coolant
Remove radiator cap① and reservoir tank cap②.
Place a pan below water pump, and drain coolant by
removing drain plug③ and water hose④.
Drain coolant from reservoir tank.
Warning !
Do not open radiator cap when engine is hot,
you may be injured by escaping hot liquid or
vapor.
Engine coolant is harmful. If coolant splashes in
your eyes or clothes, thoroughly wash it away
with water and consult a doctor. If coolant is
swallowed, induce vomiting and get immediate
medical attention.
Keep coolant away from reach of children
Clean radiator with fresh water, if necessary.
Connect water hose④ and tighten drain bolt③
securely.
Fill the specified coolant into the radiator.
Loosen bleed bolt⑤ on water pump, when coolant
flow from bleed bolt, tighten the bolt. Install radiator
cap ①securely after filling coolant.
Start the engine and keep it running for several
minutes. After warm up and cooling down the
engine, open radiator cap and check coolant. Fill the
specified coolant until the level is between the upper
and lower lines on the reservoir tank.
Caution:
Repeat the above procedures several times and make
sure the radiator is filled with coolant and air is
discharged.

Fill coolant into the reservoir tank till between upper and
lower limit.
Install reservoir tank cap.
Warning: Never mix with other brand
Inspection of Radiator Hose
Perform inspection every 40 hours or
Check radiator hose and clamp.

Leakage or Damage: →Replace
Inspection of cylinder pressure

Check cylinder pressure is necessary.
Cylinder Pressure: 1000kpa
A lower cylinder pressure may be caused by:

Excessive wear of cylinder;
Wear of piston or piston ring;
Piston ring jam in groove;
Poor closure of valve seat;
Damaged cylinder gasket or other defects
Note: When cylinder pressure too low, check the above

items.
Testing Cylinder Pressure
Note: Before testing of cylinder pressure, make sure that
cylinder head bolts are tightened to the specified torque
and valve clearance has been properly adjusted.
Warm up the engine before testing;

Make sure battery is fully charged;
Remove spark plug 1;
Install cylinder pressure gauge 2 in spark plug
hole and tighten nut;
Keep throttle full open;
Press start button crank the engine a few
seconds. Record the maximum reading of
cylinder pressure.
Tools: Cylinder Pressure Gauge
Adaptor

Inspection of Oil Pressure

Oil Pressure: 130～170kpa at 3000r/min
Lower or higher oil pressure may be caused by:
Ⅰ Oil pressure is too low
Clogged oil filter;
Leakage from oil passage;
Damaged O-ring;
Oil pump failure;
Combination of above items;
Ⅱ Oil pressure is too high

Oil viscosity is too high;
Clogged oil passage;
Combination of above items;
Testing Oil Pressure
Install hose① and hose②;
Connect tachometer③with ignition coil
Install oil pressure gauge④ and joint seat to main oil
gallery.
Warm up engine as per following:
Summer: 10 minutes at 2000r/min
Winter: 20 minutes at 2000r/min
After warming up, increase engine speed to 3000r/min,

and record readings of oil pressure gauge.
Tools：Oil pressure gauge

Tachometer

Inspection of Clutch Engagement and Lock-up

Engine is equipped with a centrifugal type
automatic clutch.
Before checking the initial engagement and clutch
lock-up two inspection checks must be performed to
thoroughly check the operation of the drive train.
I Initial Engagement Inspection
Connect tachometer to ignition coil
Start engine
Shift gear lever to “High” position
Slowly increase throttle and note down the engine
speed (r/min) when the vehicle starts to move
forward.
Engagement speed:1800r/min～2400r/min
If the engagement speed is out of the above range,
check the following:
Clutch shoes
Clutch shoe wheel
Primary and secondary sheave
Refer to Chapter 12 for inspection of clutch
II Clutch Lock-up Inspection
Connect the tachometer to ignition coil;
Start the engine;
Shift gear lever to “High” position;
Apply front and rear brakes as firmly as possible;
Fully open the throttle for a brief period and note the
maximum engine speed obtained during the test
cycle.
Lock-up Speed: 3300r/min～3900r/min
Warning:
Do not apply full power for more than 5 seconds or
damage to clutch or engine may occur.
If the lock-up speed is out of the above range, check the
following:
Clutch shoes
Clutch wheel
Primary and secondary sheave
Refer to Chapter 12 for inspection of clutch
Tool: Tachometer

3.5. Engine Removal, Inspection & Installation

Δ Engine Removal/Installation Orders and the Relative Page Numbers
Item Description Disassembly Inspection / Assembly Remarks
Maintenance
Engine Water Hose/Pipe 15-2 15-11 15-69
Periphery Left Side Cover 15-2 — 15-68
Spark Plug 15-2 15-4 15-68
Cylinder Head Cover 15-3 15-14 15-66
Tensioner 15-3 15-24 15-67
Engine
Camshaft 15-3 15-21 15-65
Front Cylinder Head/Tensioner Plate 15-4 15-15/15-23 15-64
Side Cylinder/Timing Chain Guide 15-4 15-24/15-23 15-64
Piston 15-5 15-25 15-62
Starting Motor 15-5 15-3 15-62
Oil Filter 15-6 15-9 15-62
Sector Gear 15-6 — 15-62
Engine Water Pump 15-7 15-7 15-61
Sheave Drum 15-7 15-48 15-60
Left Side Left Crankcase Cover/ Magneto Stator 15-7 15-48 15-60
Magneto Rotor 15-7 15-47 15-60
Starting Driven Gear 15-8 15-47 15-59
Starting Dual Gear/Idle Gear 15-8 15-48 15-59
Oil Pump Sprocket and Chain 15-8 — 15-59
CVT Cover 15-9 15-51 15-58
Drive Belt 15-9 15-36 15-57
Engine
Primary Sheave/Secondary Sheave 15-9 15-30 15-57
Right CVT Housing/Clutch Outer Face 15-10 15-51 15-57
Side Clutch 15-10 15-28 15-56
Timing Chain 15-10 15-23 15-56
Gear Position Bolt 15-11 — 15-56
Right Crankcase 15-11 15-52 15-56
Front Output Shaft Components 15-11 15-43 15-55
Driven Bevel Gear Components 15-11 15-43 15-55
Shift Cam 15-12 15-40 15-55
Engine
Guide Bar, Fork 15-12 15-39 15-55
Drive Bevel Gear Components 15-12 15-42 15-55
Center
Main Transmission Shaft 15-12 15-38 15-54
Transmission Counter Shaft 15-12 15-38 15-54
Balancer Shaft 15-12 15-46 15-54
Crankshaft 15-13 15-27 15-54
Oil Pump, Pressure-limiting Valve 15-13 15-41 15-53
Left Crankcase 15-52
Notes: Arrowhead direction is for engine removal orders. Reverse the direction for assembly and installation
15-1

Ⅰ
Engine Removal
ΔPreparation before engine removal
Prepare a proper tray used for load of components
Prepare necessary removal and assembly tools
Drain up engine oil（→11-8）
Drain up coolant（→ 11-10）
△ Engine Periphery
Water Hose/Pipe
Remove water hose clamp① and②;

Remove water hose③
Remove screw④ and water hose⑤
Left Side Cover

Remove 4 bolts(M6X12) of left side cover
Remove left side cover
Inspection Plug
Remove inspection plug⑥ with screwdriver
ΔEngine Front Side

Spark Plug
Remove spark plug⑦ with special wrench

Tool: Spark Plug Wrench
Turn crankshaft, align T.D.C. line A on magneto rotor

with mark B of left crankcase

Cylinder Head Cover

Remove valve adjusting cover
Remove12 bolts of cylinder head cover
Remove cylinder head cover
Timing Chain Tensioner
Remove screw plug①, insert a flat screwdriver into

slot of timing chain tensioner adjuster , turn it
clockwise to lock tensioner spring;
Remove tensioner fix bolt
Remove tensioner and gasket
Camshaft
Loosen timing sprocket bolt;
Remove timing sprocket bolt and lock;

Remove C-ring①
Remove timing sprocket from camshaft, remove
camshaft
Note: Take care not to drop spacer, bolt, bolt lock

and C-ring into crankcase.
Remove tensioner plate
Cylinder Head
Remove cylinder head bolt
Remove cylinder head bolts diagonally;
Remove cylinder head
Note: Take care not to drop dowel pin into

crankcase
Cylinder
Remove dowel pin and cylinder head gasket
Remove timing chain guide①

Remove cylinder bolt

Remove cylinder
Note：Take care not to drop dowel pin

into crankcase
Remove dowel pin and cylinder gasket
Note：When performing above removal process,

be sure to hook up timing chain to
prevent it from falling into crankcase
Piston
Remove piston pin circlip① with long nosed pliers
Note: Put a clean rag under piston so as not to

drop piston pin circlip into crankcase
Remove piston pin②and piston③
Notes:
When installing piston, make sure its
identification conforms to that of cylinder;
When removing piston pin, clean off burrs of
piston pin hole and groove. If it’s difficult to
remove the piston, DO NOT hammer, use a
special remover④
Tool: Piston Pin Remover
ΔEngine Left Side
Starting Motor
Remove 2 bolts of starting motor
Remove starting motor

Oil Filter
Remove oil filter with special tools
Tool: Oil filter Remover
Sector Gear
Remove bolt of sector gear housing cover
Remove wire clip and sector gear housing cover
Remove dowel pin and gasket

Remove drive sector gear 1
Remove bolt 2 of driven sector gear
Remove washer3 and driven sector 4

Water Pump
Screw out bolt of water pump
Remove water pump
SPLINED SPACER
Remove bolt and washer;
Remove splined spacer
Left Crankcase Cover

Remove bolts; Remove left
crankcase cover Remove
dowel pin and gasket
Magneto Rotor
Install the bolt M10×1.25×40 into crankshaft.
Use the rotor assy puller.
Tool: Rotor Remover

Starting Motor Gear

Remove driven gear ① and needle bearing
Remove spacer ②
·Remove dual gear and shaft ③

·Remove idle gear and shaft ④
Oil Pump Sprocket and Chain
Remove drive sprocket nut ⑤

Remove C-ring ⑥
Remove oil pump drive and driven sprockets and
chain

Δ Engine Right Side
CVT Cover
Remove bolt of CVT cover
Remove CVT cover
Remove gasket and dowel pin
CVT(Continuously Variable Transmission)
Remove primary sheave nut with special tool

Remove primary sliding sheave
Remove secondary sheave nut with special tools

Remove secondary sheave
Remove drive belt
Tool: Sheave Holder
Remove primary fixed sheave ①
Remove bolt for air guide plate.
Remove air guide plate

CVT Case
Remove bolt 1 of CVT case
Remove bolt 2 of CVT case
Remove outer clutch face and CVT case
Remove dowel pin, front and rear gasket
Clutch
Remove one-way clutch
Remove clutch shoe fixing nut with special tool
Remove clutch shoe.
Note: The clutch shoe nut has left-hand threads.
Timing Chain
Remove timing chain

Engine Center
Gear position bolt
Remove gear position bolt 1

Remove spring and steel ball
Right Crankcase
Remove left crankcase bolts
Remove right crankcase bolts
Separate right crankcase with special tool
Caution
The Crankcase separator plate
should be parallel with the end face
of crankcase
Crankshaft should remain in the left
crankcase half.
Driven Bevel Gear, Front Output Shaft

Remove bevel gear cover bolt
Remove driven bevel gear ③
Remove front output shaft nut ④

Remove Oil seal①, Bearing limit nut②

Remove Bearing③, Front Output Shaft ④
Shift Cam, Fork/Shaft

Remove Shift Cam⑤, Fork /Shaft⑥
Drive Bevel Gear

Remove left crankcase from driven bevel gear
Drive Shaft, Drive Shaft
Remove drive shaft⑦ and driven shaft⑧
Balancer Shaft
Remove balancer shaft

Crankshaft
Separate crankshaft from left crankcase with special

tool
Tool: Crankshaft Separator
Oil bump, Relief Valve
Remove oil bump and relief valve

Engine Components Inspection
Cylinder Head Cover
Disassembly
Caution: Each removed part should be identified to its
location, and the pars should be laid out in groups
designated as “Exhaust”, “Intake”, so that each will be
restored to the original location during assembly.
Remove rocker arm shaft bolts A
Remove rocker arm shaft by using M6 bolts B
Cylinder Head Cover Distortion
Clean off sealant from the fitting surface of cylinder head

cover, place cylinder head cover on a surface plate and
measure distortion with a thickness gauge.
Cylinder head Cover Distortion

Limit: 0.05mm
Tool: Thickness Gauge
Distortion out of range: → Replace
Note: Cylinder head cover and cylinder head should be

replaced together.
Rocker Arm Shaft
Measure out diameter of rocker arm shaft with a

micrometer.
Rocker Arm Shaft O.D.: (IN, EX)
Limit: 11.973~11.984mm
Tool: Micrometer (0~25mm)

Rocker Arm
When checking the rocker arm, check the inner

diameter of the valve rocker arm and wear of the
camshaft contact surface.
Rocker Arm I.D. : .000~12.018mm
Tool: Dial Calipers
Assembly
Note: Intake rocker arm shaft A has oil holes.
Apply engine oil to rocker arms and shafts;

Install rocker arms and tighten rocker arm shaft to
the specified torque:
Rocker Arm Shaft Bolt: 28N.m
Cylinder Had
Disassembly
Remove intake pipe
Remove water temperature sensor ①and

thermostat cover ②

Remove thermostat
Compress the valve spring and remove valve cotter

with tweezers.
Tools: Valve Spring Compressor

Tweezers
Remove valve spring upper seat and valve spring
Remove valve from the other side.
Remove valve stem seal ring and valve lower seat.

Cylinder Head Distortion
Clean off carbon deposit from combustion chamber;

Check the gasket surface of the cylinder head for
distortion with a straightedge and thickness gauge. Take
clearance readings from several places. If any clearance
reading is out of the service limit, replace with a new
cylinder head.
Cylinder Head Distortion Service Limit: 0.05mm

Valve Seat Width

Coat the valve seat with color uniformly. Fit the
valve and tap the coated seat with the valve face in
a rotating manner. To get a clear impression of the
seating contact, use a valve lapper to hold the valve
head.
The ring-like dye impression on the valve face
should be continuous, without any break. The width
of the dye ring, which is the visualized seat width,
should be within the following range:
Valve Seat Width: 0.9-1.1mm

Tool: Valve Lapper
Valve Stem and Valve Guide
Lift the valve about 10mm from valve seat. Check

the valve stem deflection in the directions of X and Y
perpendicular to each other, with a dial gauge. If the
deflection measured is out of the limit, replace either
the valve or the valve guide. (If the valve stem is
worn to the limit and the clearance is found to be in
excess of the limit, replace the valve. If the valve
stem is within the limit, replace the valve guide.
Double check the clearance after replacing the
valve stem or the guide).
Valve Stem Deflection (IN & EX): 0.35mm

Tool: Micrometer
Magnetic Stand

Valve Stem O.D

Measure valve stem O.D with a micrometer
Service Limit
IN: 4.975-4.990mm
EX: 4.955-4.970mm
Tool: Micrometer (0-25mm)
Valve Stem Run-out

Support valve stem with V block as illustrated on the
right. Check the run-out with a dial gauge.
Tool: Magnetism Stand
Dial Gauge (1/100)
V block
Valve Head Radial Run-out

Measure the valve head radial run-out as illustrated
on the right.
Valve head Radial Run-out out of range: →Replace
Tool: Dial Gauge (1/100)
Magnetic Stand
V Block
Valve Face Wear

Check each valve face for wear or damage.
Replace valve with a new one if it is found to have
abnormal wear. Measure valve head thickness T.
Valve head thickness T out of range: → Replace
Valve Stem End

Check valve stem end for pitting or wear. In case of
any pitting or wear, resurface the valve stem end. If
the length T is less than service limit, replace valve
with a new one.
Valve Stem End Length

Valve Spring
Valve Spring keeps valve and valve seat tight.

Weakened spring results in reduced engine power
output and chattering noise from valve mechanism.
Measure the spring free length.

Spring free length out of range: →Replace
Tool: Vernier Caliper.
Measure the force to compress the spring to the

specified length.
Valve spring tension out of range: → Replace
Service Limit: (IN/EX)
182N-210N/31.5mm
Tool: Spring Scale.
Measure valve spring incline.

Spring incline out of range:→ Replace
Valve Spring Incline Limit: 2.5º/1.7mm
Assembly of Cylinder Head

Install each valve spring seat;
Apply moly oil to valve stem seal and fit into
position.
Material: Moly oil
Note: Do not reuse the valve stem seal.
Insert the valves, with stems coated with moly oil all
around.
Note: When inserting the valve, be careful not to

damage the lip of the stem seal.

Install valve spring with small-pitch end “b” facing

cylinder head. Big-pitch end “a” is marked.
Put on the valve spring retainer. Use the valve

spring compressor to press down the spring. Fit the
two cotter halves to the stem end and release
compressor to allow the cotter ① to wedge in
between seat and stem. Make sure that the rounded
lip② of the cotter fits into the groove③ in the stem
end.
Tool: Valve Spring Compressor

Tweezers
NOTE: Knock the valve end with rubber

hammer. Make sure valve cotter is
fit into groove.
Check the sealing effectiveness of cylinder head.

Dip clean solution into valve IN/EX ① and check
for any leakage of valve seat ② after a few
minutes.

Install thermostat
Install thermostat cover
Install water temperature sensor, apply thread

locker to the thread part, tighten it to the
specified torque.
Water temperature sensor

Tightening torque: 10 N·m
Install intake pipe, apply lubricant to 0-ring.
Camshaft
Check camshaft for wear and run-out of cams and

journals if the engines produces abnormal noise or
vibration or lacks power output. Any of these symptoms
could be caused by wear of camshaft.
Note: Do not try to disassemble the camshaft/automatic

decompression assembly. It is not serviceable.

Automatic Decompression
Move the automatic decompression weight with
hand and check if it is operating smoothly. If it is
not working smoothly, replace with a new
camshaft/automatic decompression assembly.
Cam Wear
Worn cams can often cause mistimed valve
operation resulting in reduced power output. The limit of
cam wear is specified for both IN and EX cams in terms
of cam height “a”. Measure with a micrometer the cam
height.
Cam height out of range: →Replace
Cam height service limit:
IN: 33.130mm
EX: 33.200mm
Tool: micrometer (25-50mm)
Camshaft Journal Wear

Check whether each journal is worn to the limit by
measuring camshaft journal oil clearance with the
camshaft installed.
Camshaft journal oil clearance
Service limit: 0.15mm
Check according to the following steps:
Clean off materials from cylinder head and cover;
Install camshaft with plastic gauge;
Install cylinder head cover and tighten bolts evenly
and diagonally to the specified torque:
Remove cylinder head cover, read the width of the
compressed plastic gauge with envelop scale. The
reading should be taken from the widest part.
Tool: Plastid Gauge
Note: Do not turn the camshaft with plastic gauge in

place.
If the camshaft journal oil clearance exceeds the limit,

measure the outer diameter of camshaft;
Replace either cylinder head set or the camshaft if the

clearance is not correct.

Camshaft Journal O.D.
Measure camshaft journal O.D. with a micrometer.

If the O.D. is out of range, replace camshaft with a
new one.
Camshaft journal O.D. service limit:
Sprocket end: 22.959 mm—21.980mm

Other end: 17.466mm—17.484mm
Tool: micrometer (0-25mm)
Camshaft Run-out
Measure the run-out with a micrometer. Replace
camshaft is the run-out is out of range.
Service limit: 0.10mm
Timing Sprocket and Chain
Check timing sprocket and chain for wear or

damage.
Replace with new parts if abnormal wear or damage
is found.
Tensioner and Chain Guide
Check contact surface of tensioner and chain guide

for wear and damage.
Replace with news parts if abnormal wear or

damage is found.

Chain Tensioner
Inspection
Check tensioner for any damage or poor function.
Damage, poor function: →Replace
Insert screw driver into the slotted end of adjusting

screw, turn it clockwise to loosen the tension and
release the screwdriver.
Check the push rod movement. If the push rod is
stuck or there is a failure with spring mechanism,
replace the chain tensioner with a new one.
Cylinder
Cylinder Distortion
Check the gasket face of cylinder for distortion with
a straightedge and thickness gauge and take
clearance readings at 7 points as illustrated. If the
largest reading at any of the 7 points of the
straightedge is out of the range, replace the
cylinder.
Cylinder Distortion Service Limit: 0.05mm
Tool: Straightedge
Thickness Gauge
Cylinder Bore
Check cylinder wall for scratches, nicks or other
damage. Replace with a new one if any.
Measure cylinder bore diameter at three points of
upper, middle and lower.
Standard Cylinder Bore: 87.500-87.522mm

Tool: Cylinder Gauge Set

Piston
Piston Diameter
Use a micrometer to measure the diameter at the
point 10mm above the piston end, as illustrated on
the right. If the measurement is less that the limit,
replace the piston
Standard: 87.460-87.480mm
Limit: 87.380mm
Tool: Micrometer (75-100mm)
Calculate the piston to cylinder clearance according

to the above measurement.
If the clearance is more than 0.15mm, replace the
cylinder or piston, or both.
Piston Ring to Groove Clearance

Use a thickness gauge to measure the side
clearance of topt ring and 2nd ring.
If the clearance exceeds the limit, replace both
piston and piston rings.
Service Limit:
Top ring: 0.18mm
2nd ring: 0.15mm
Standard width of piston ring groove

Top ring: 1.03-1.05mm
2nd ring: 1.22-1.24mm
Oil ring: 2.51-2.53mm
Standard thickness of piston ring

Top ring: 0.970-0.990mm
2nd ring: 1.170-1.190mm
Tools: Thickness gauge

Micrometer (0-25mm)

Piston Ring Free End Gap and End Gap

Before installing piston rings, use vernier caliper to
measure the free end gap of each ring, and then fit
ring into the cylinder.
Use thickness gauge to measure each ring end gap,
if any ring has an excess end gap, replace the
piston ring.
Piston ring free end gap limit:

Top ring: 8.9mm
2nd ring: 9.5mm
Piston ring end gap limit:

Top Ring: 0.60mm
2nd ring: 0.60mm
Tool: Vernier caliper

Thickness gauge
Piston Pin and Pin Bore

Use a bore gauge to measure the inner diameter of
piston pin bore.
Use micrometer to measure outer diameter of piston
pin.
If out of limit, replace both piston and piston pin.
Piston pin bore limit: 23.030mm
Use micrometer to measure piston pin outer

diameter at three points
Piston pin outer diameter limit: 22.980mm

Tools: Bore gauge (18-35mm)
Micrometer (0-25mm)

Connecting Rod/Crankshaft
Connecting rod small end I.D.
Use a dial gauge to measure the I.D. of connecting
rod small end. If the measurement exceeds the limit,
replace the connecting rod.
Connecting rod small end I.D. : 23.040mm

Tool: Dial Gauge (18-35mm)
Connecting Rod Deflection

Check the movement of the small end of the rod and
inspect the wear of the small end. This method is
also applicable to check and inspection of big end.
Connecting Rod Deflection: 3.0mm

Tools: Dial Gauge
Magnetic stand
V-block
Connecting Rod Big End Side Clearance

Push the big end to one side, and use thickness
gauge to measure the other side clearance.
If out of limit, replace with a new crankshaft.
Connecting Rod big end side clearance: 1.0mm

Crankshaft Run-out
Support crankshaft with “V” blocks as illustrated. Put
the dial gauge, slowly turn the crankshaft and
measure run-out with a dial gauge.
If the run-out exceeds the limit, correct or replace
the crankshaft.
Run out limit: 0.08mm

Tools: dial gauge
Magnetic stand
V-block

Clutch
Clutch Shoes
Check clutch for chipping, scrape, uneven wear or
heat discoloration. At the same time check depth of
the grooves of clutch shoes. If any of the clutch
shoes has no groove, replace the clutch.
Note: clutch should be replaced as a set.
Clutch Wheel
Check the inner clutch wheel ① for scratches, scuffs or
blue discoloration or uneven wear. If any damage is
found, replace the clutch wheel with a new one.
Check oil seal lip for wear or damage.
Wear or Damage: →Replace
Use special tool to remove oil seal
Tool: Oil seal remover
Use special tool to assemble oil seal
Tool: Oil seal installer set
Check the turning of bearing.
Abnormal damage: →Replace
Assembly
Apply lubricant grease to oil seal when assembling.

Primary and Secondary Sheave

Primary Sliding Sheave
Disassembly
Remove spacer
Remove Cam ①and Roller②
Roller
Check each roller and sliding face for wear and
damage.
Wear and damage: →Replace
Note: rollers should be replaced as a set.
Oil Seal
Check oil seal lip for wear and damage.
Wear and damage: →Replace
Remove the oil seal

Primary Sliding Sheave and Fixed Sheave

Check the drive face for any abnormal conditions
such as damage or stepped wearing.
Damage or wearing: → Replace
Install oil seal with special tool.

Tool: Bearing install set
Assembly
Reverse the removal procedure of primary sliding and
fixed sheave for installation.
Pay attention to the following:
Apply grease to inner bore and oil seal lip.
Note:
Wipe off any excessive grease thoroughly.
Take care not to attach any lubricant grease
to contact surface of drive belt.
Material: Lubricant grease
Position 8 rollers ①on the primary sliding sheave

Install 4 dampers ② to cam ③
Install cam to primary sliding sheave.
Notes:
When inserting the spacer, press down the cam
so that the rollers will not come out of position.

Install spacer
Secondary Sheave
Disassembly
Use special tool and holder to hold the secondary
sheave. Remove secondary sheave nut with special
tool.
Caution:
Do not remove the ring nut before attaching the
clutch spring compressor.
Tool: Nut Wrench

Sheave Holder
Attach special tool to the secondary sliding sheave

and compress it by turning in the tool handle.
Note:
Make sure that spring end A is inserted into slot
B of the tool handle.
Remove ring nut.

Tool: Secondary sliding sheave spring compressor
Note:
Since a high spring force applies to the
secondary sliding sheave, take special care that
the secondary sliding sheave will not come off
abruptly.
Slowly loosen tool handle and remove the special

tool.

Remove spring ①
Remove spring seat ②.
Remove guide pin and spacer.
Remove secondary sliding sheave ③
O-ring and Oil Seal
Check the O-ring and oil seal for wear and damage.
Wear and Damage: → Replace
Remove Oil Seal

Install oil seal with special tool.

Tool: Bearing install set
Secondary Sheave Spring

Use vernier caliper to check the spring free length. If
the length is shorter than the service limit, replace
with a new one.
Secondary Sliding and Fixed Sheave

Check drive face for any abnormal condition such
as stepped wear or damage.
Wear or damage: → Replace
Assembly
Install a new O-ring
Apply lubricant grease to O-ring, oil seal lip and
guide pin groove.
Material: lubricant grease

Install guide pin and spacer ①
Note: To avoid damage to the oil seal lip during

assembly, slide the lip with a 0.1mm steel sheet
as guide.
Install spring seat. Align hole A with hole B.
Install spring and spring plate. Insert spring end into

the hole.
Compress spring with special tool.

Align the secondary sheave end with spring plate
hole.
Tool: Secondary sheave spring compressor
Tighten ring nut temporarily.

Remove the special tool from secondary sheave.

Tighten the ring nut with special tool to the specified

torque.
Ring Nut Tightening Torque: 100N·m

Tool: Ring nut wrench
Sheave Holder
Drive belt
Check belt for any greasy substance.

Check contact surface of belt for any cracks and
damage.
Check belt width with vernier caliper.
Damage, width out of range: →Replace
Belt width service limit: 33.5mm

Tool: vernier caliper
Caution:
If belt surface is stained with grease or oil, degrease the
belt thoroughly.

Transmission
No. Description Qty No. Description Qty.

1 MAIN SHAFT. GEARSHIFT 1 10 DRIVEN GEAR, HIGH RANGE 1
2 SHIFT CAM 1 11 DRIVEN GEAR, LOW RANGE 1
3 RIGHT CRANKCASE 1 12 SPRING, SHIFT FORK 1
4 LEFT CRANKCASE 1 13 RIGHT SHIFT FORK 1
5 DRIVEN SECTOR GEAR 1 14 GUIDE BAR 1
6 SPROCKET, REVERSE GEAR 1 15 DRIVEN SHAFT 1
7 CHAIN, REVERSE GEAR 1 16 SPRING, SHIFT FORK 1
8 DRIVEN OUTPUT GEAR 1 17 LEFT SHIFT FORK 1
9 DRIVE SECTOR GEAR 1 18 SHIFT FORK ASSEMBLY 1

Inspection
Check main shaft gear and sprocket surface for any
damage or over wear.
Damage or over wear: → Replace
Check reverse gear chain for any damage or over

wear.
Disassemble driven shaft as illustrated.
Check each gear surface for any damage or over

wear.
Check bearing and collar for any wear or damage..

Check the shift fork clearance with a thickness

gauge in the groove of its gear.
Clearance exceeds the limit: → Replace
Shift fork to Groove clearance

Standard clearance :0.10-0.30mm
Service Limit :0. 50mm
Measure shift fork groove width with vernier caliper
Standard shift fork groove width: 6.05-6.15mm
Measure shift fork thickness with vernier calipers;
Standard fork thickness: 5.08-5.90mm
Check shift fork ① and ② for damage or bend
Damage, bend: → Replace
Install shift fork to guide bar and move left and right.
In case of any unsmooth moving, replace with a new
one.

Put the guide bar on a flat plate and roll it. In case of
any bend, replace with a new one.
NOTE:DON NOT attempt to correct a bent guide bar.
Check shift fork spring for breakage, damage

Broken or damaged: → Replace
Check shift cam groove for scratches, damage.

Scratch or damage: → Replace
Assembly
Reverse the removal procedure for assembly. Pay

attention to the following:
Use new retainers. Pay attention to the direction of

the retainers. Fit to the side where the thrust is as
illustrated.
Coat the gears and shafts with engine oil before

assembly.
Note:
Do not reuse the retainers
Do not expand of the gap end of new retainers too
wide when assembling.
Make sure that all the retainers are properly fitted.

When assembling the guide bar, take care not to

assemble the two shift forks and springs in the
opposite direction.
1. Guide bar 2. Retainer

3. Left shift fork 4. Shift fork Spring (small)
5. Right shift fork 6. shift fork spring (big)
7. Spring seat
OIL PUMP
Disassembly oil pump as illustrated:
1. Oil pump housing 2.Dowel pin
3.Oil pump shaft 4.Straight pin
5.Inner rotor, oil pump 6.Outer rotor, oil pump
7. Oil pump cover
Check oil pump housing and cover for cracks and

damage.
Crack or damage: → Replace
Measure top clearance “a” between inner and outer

rotors and side clearance “b” between outer rotor
and oil pump housing. If the clearance exceeds the
limit, replace with new one.
Top Clearance:0. 03-0.10mm

Service Limit: 0. 15mm
Side clearance: 0. 03-0.10mm


Oil strainer
Check oil strainer ① and O-ring ② for damage
Damaged oil strainer: → Replace
Clean the surface of oil strainer with engine oil
Relief Valve
Check the valve body ① 、valve ② and spring ③O
ring④ for damage or wear.
Damage or wear: → Replace
Drive Bevel Gear

Use a clean rag to protect the drive bevel gear shaft,
clamp it to the pliers.
1. Drive bevel gear cover 5. Adjust washer

Loosen drive bevel gear nut 3, remove the drive 2. Output driven gear 6. Drive bevel
bevel gear 4 and adjust washer 5 gear shaft
3. Drive bevel gear nut 7. Bearing press
Check the drive bevel gear 4 and output driven gear 4. Drive bevel gear 8. Bearing
2 for rust, scratch, wear or damage. Replace if any.
Check if the bearing 8 turns smoothly, replace with a

new bearing if necessary.
Adjust Washer 5 if any of right crankcase, drive

bevel gear 4, or drive bevel gear cover 1 is replaced.
Refer to bevel gear adjustment for details.
Apply engine oil to bearing 8 when assembling and

tighten nut 3 to the specified torque.
Drive bevel gear nut

Tightening torque: 145N.m

Front Output Shaft

Check bearing 7 for smooth turning and abnormal
wear. Check oil seal 5 for damage.
Apply lubrication oil to bearing 7 and oil seal 5 lip

before assembly.
Apply thread locker to bearing limit nut 6 (left thread)

and tighten to the specified torque.
Bearing limit nut Tightening torque: 80N.m
Tighten Nut 1 to the specified torque

Front output shaft nut tightening torque: 97N.m
Driven Bevel Gear

Remove nut 19, washer 18, coupler 17 and oil seal 16.
Protect end thread of driven bevel gear with proper

device ②. Fix bevel gear cover 14 and press out
driven bevel gear.
Place a clean rag ① under bevel gear cover.
Remove bearing limit nut 10 with special tool ② and
remove bearing.
Check driven bevel gear 8 surface for scratches,

wear. Scratch or wear: → Replace
Check free turning of bearing 9 and 11. Replace

with a new one if any abnormal is found.
Use new oil seal 16 and O-ring 12 when

assembling.
Adjust washer 13 if any of right crankcase, driven

bevel gear 8 or driven bevel gear cover 14 is
replaced. Refer to bevel gear adjustment for
details.
Apply lubrication oil to bearing 9 and 11 and oil seal

16, O-ring. Apply thread locker to nut 10 and tighten
to the specified torque.
Tightening torque :110N.m
Tool: driven bevel gear nut wrench
Driven bevel gear nut tightening torque:150N.m
Bevel Gear Washer Adjustment
Adjust washer ① and ② when replacing crankcase

and/or bevel gear and/or bevel gear cover,

Bevel Gear
Note: Proper bevel gear engagement depends

on that the gear backlash and tooth contact are
within the proper range.
Bevel Gear Backlash

Install drive and driven gears to the
crankcase. Wrap a (--) screwdriver ③with a
rag ② and insert it into the speed sensor
hole ① of left crankcase to fix the drive
bevel gear.
Install special tool ③ and micrometer ④.

Tool: Bevel gear side clearance dial gauge
Micrometer
a=46mm
Turn the driven bevel gear in each direction

and measure the backlash.
NOTE: Measure four points in the mutual

vertical direction
If the backlash is not within the
specification, adjust the thickness of the
driven bevel gear adjust washer. Re-check
the backlash until the backlash is correct.
Bevel Gear Backlash: 0.1-0.2mm
Adjustment
Measured Backlash Washer Thickness

Adjustment
＜0.1mm Decrease washer thickness
0.1~0.2m Correct
＞0.2mm Increase washer thickness

Tooth Contact
After adjusting the backlash, check the tooth contact
according to the following procedures:
Remove drive and driven bevel gear shafts from

crankcase;
Clean and degrease every tooh of drive and driven

bevel gear;
Coat the driven bevel gear with machinist’s layout

dye or paste;
Install drive and driven bevel gear;
Rotate the driven bevel gear several turns in both

directions;
Remove drive and driven bevel gear shafts and

check the coated teeth of the drive bevel gear;
Refer to the illustration on the right for tooth contact

pattern ①, ② and ③
① Incorrect (contact at tooth top)
② Correct
③ Incorrect (contact at tooth bottom)
If tooth contact is correct (Contact ②), continue the

next procedure.
If tooth contact is not correct (② and ③), adjust the
thickness of the washer of drive bevel gear. Repeat
above steps to check tooth contact until it is correct.
Adjustment
Tooth Contact Washer Adjustment

Contact at tooth top ① Increase Thickness
Contact at tooth Decrease Thickness
bottom ③
Note:
After adjusting the tooth contact, the backlash must
be checked again;
If the backlash is adjusted but tooth contact is still
out of specification, replace the drive and driven
bevel gears;
Both tooth contact and backlash should be within
the required specification.

Balancer Shaft
Remove the parts as illustrated on the right. Check
each part for abnormal wear or damage.
① Balancer shaft gear
② Woodruff key
③ Balancer shaft
④ Balancer shaft sprocket
⑤ Washer
⑥ Bolt
Magneto Rotor
Remove starter clutch nut;

Check starter clutch roller and holder for abnormal

wear or damage.
Install the starter clutch in the correct direction.
Note:
When install the starter clutch to the magneto rotor,
make sure side “A” is in the right direction.
Face arrow mark “B” to the engine side;

Apply engine oil to starter clutch.
Apply thread locker to bolt and tighten to the

specified torque:
Tightening torque of starter clutch bolt: 30N.m

Material: Thread Locker
Install the starter driven gear
Make that the starter driven gear turns in the

opposite direction of the arrow mark “B”. The gear
cannot turn in the direction of the arrow.
Check starter driven gear bearing. In case of

anything unusual, replace the bearing.
Remove starter driven gear bearing with special tool
Install starter driven gear bearing with special tool.
Tool: Bearing Installer/Remover

Electric Starter Gear

Check the gear surface for scrap or damage.
Scrape or Damage: → Replace
LEFT CRANKCASE COVER
Check magneto stator coil 2, pickup coil 3 for

damage,
burn or short circuit, if any , replace with new one;
Check bearing 4 for smooth turning. If it is stuck,

replace with a new one;
Check oil seal 5 for damage. Replace it if it’s

damaged;
Apply thread locker to the bolt when assembling.

Tightening torque for magneto coil bolt: 10N.m
Apply lubrication oil to bearing 4 and lubricant

grease to lip of oil seal 5 when assembling.
LEFT SIDE COVER
Disassembly
1— Left side cover

2— Bolt
3— Washer
4—Splined spacer

CVT Cover
Remove screw 5, oil seal limitator 4. Remove oil
seal 3 with special tool;
Check bearing 2 for free turning. In case of any

abnormal, remove with special tool and replace with
a new bearing;
Apply lubrication oil to outer ring of bearing and

install bearing with special tool. Check bearing for
smooth turning.
Apply grease to bearing inner side;
Apply grease to oil seal lip and install oil seal with
special tool.
Note: Use a new oil seal.
Install oil seal limitator and tighten screw after

applying thread locker.
Tool: Bearing Remover

Oil Seal Remover
Bearing Installer
CVT Case
Check bearing 5 for smooth turning. In case of any

abnormal, remove screw 3 and bearing retainer 4
and replace with a new bearing.
Check oil seal 7. In case of any damage, replace it;
Apply grease to oil seal lip and install with special

tool.
Apply lubrication oil to bearing 5 and install with

special tool; Check bearing for smooth turning. The
seal side of bearing 5 should face bearing retainer
4.
Install bearing retainer 4 and screw 3.
Install oil seal 1 into clutch housing 2 with special

tool.
Tool: Oil Seal Installer
Bearing Installer

Crankcase
1. Right Crankcase 10. O-ring 19. Bearing

2. Bearing 11. Gear Sensor 20. Bearing
3. Seal 12. Left Crankcase 21. Bearing
4. Bearing 13. Oil Plug 22. Oil Dip Rod
5. Bearing 14. Oil Pipe 23. O-ring
6. Bearing 15. Link Bolt 24. Speed sensor
7. Oil Seal 16. Washer 25. Bolt
8. Washer, Reverse Gear Sensor 17. Bearing 26. Washer
9. Reverse Gear Sensor 18. Bearing 27. Oil Drainage Bolt
Clean and grease the bearings, turn the inner race

of bearing and check the play, noise and smooth
turning. In case of any abnormal, remove bearing
with special tool and replace;
Check all the oil seals for over wear or damage. In
case of any over wear or damage, remove with
special tool and replace with a new oil seal;
Remove gear sensor 11 and check for continuity
with reverse gear sensor 9 with a multimeter.
Remove link bolt and oil pipe 14 and check oil pipe
for crack or clog. Replace with a new one if any;
Remove oil drainage bolt 27 and clean it.
Note: Check bearing for smooth turning after installation.

Install new O-ring and apply grease;

Install gear sensor;
Install reverse gear sensor 9 and tighten to the
specified torque.
Reverse gear sensor tightening torque: 20N.m
Install speed sensor 24
Install oil pipe and tighten the link bolt to the

specified torque;
Link bolt tightening torque: 40N.m
Install washer 26 and oil drainage bolt 27 and

tighten to the specified torque;
Drain bolt tightening torque: 30N.m
Tool: Bearing Remover

Bearing Installer
Multimeter
III Engine Assembly
Reverse the engine removal procedure for installation.
Caution:
Clean all the parts before assembly;
Make sure that the parts are in good condition
without any damage;
Apply engine oil to the moving parts before
assembly;
Apply grease to oil seal lip and O-ring
Caution:
Make sure that drive belt, primary and secondary
sheaves are not stained with grease.
Engine Center
Oil Pump and Relief Valve
Install oil pump and relief valve to left crankcase, as

illustrated on the right. Tighten to the specified
torque:
Oil pump bolt: 10N.m

Relief valve bolt: 10N.m

Connecting Rod
Install connecting rod to left crankcase with special

tool;
Note:
Do not hammer the conrod into crankcase with
plastic mallet;
Use special tool to avoid affect of conrod precision
Tool: Conrod Installer
Balancer Shaft
Install balancer shaft
Caution: Balancer shaft driven gear should be aligned to

the mark as illustrated.
Main Shaft, Counter Shaft
Install main shaft and counter shaft.

Shift Cam, Shift For
Install shift can① and shift fork②
Check each part for smooth turning
Install low range driven gear to counter shaft③
Spray adequate engine oil to each part.
Drive Bevel Gear
Install drive bevel gear and tighten to the specified

torque.
Drive bevel gear tightening torque: 32N. m

Material: Thread Locker
Right Crankcase
Driven Bevel Gear
Install driven bevel gear and tighten to the specified

torque.
Driven bevel gear tightening torque: 25N. m
Check bevel gear backlash (Refer to 12-44)
Front Output Shaft
Install front output shaft to right crankcase

Apply sealant ①to the mating face of right

crankcase.
Note: Apply sealant evenly in an uninterrupted thin line.
Install 5 dowel pins②
Assemble crankcase and tap slightly with a rubber

hammer so that the crankcase is properly fitted.
Install bolt and tighten to the specified torque.
Crankcase bolt tightening torque: M6: 10N.m

M8: 25N.m
Note: Crankcase bolts should be tightened diagonally in

several steps.
Place the steel ball and install gear positioning bolt

and tighten the bolt to the specified torque.
Gear positioning bolt tightening torque: 40N.m
Engine Right
Timing Chain
Put on timing chain 2
Clutch
Install clutch 1 and nut 2. Tighten the nut to the

specified torque (left thread).
Clutch nut tightening torque: 80N.m

Install new o-ring⑥ in spacer⑧
Install spacer onto the clutch housing shaft, then

install into CVT case
Note: align oil nick on spacer with oil hole on the shaft
CVT Case
Install dowel pin ④, gasket ② and gasket⑤ to the

right crankcase. Install CVT case assembly to right
crankcase.
Install bolt ⑿ and nut③
Note:
Tighten bolt/nut diagonally
Use a new gasket
Install air guide plate⑩ and screw⑾
Primary Sheave, Secondary Sheave, Drive Belt
Install primary fixed sheave ①as illustrated on the

right;
Install drive belt between secondary sliding/fixed

sheave and tap with a plastic hammer to keep the
belt as low as possible.
Note:
Install the drive belt with the arrow on the belt turn in
the clockwise direction
Drive belt contact surface should be free from any

stains.

Install secondary sheave;
Install primary sliding sheave
Tighten primary sheave nut with special tool to the

specified torque;
Primary sheave nut tightening torque: 115 N·m

Tool: Rotor Holder
Tighten secondary sheave nut with special tool to

the specified torque;
Secondary sheave tightening torque: 115 N·m

Tool: Rotor Holder
Note:
Turn the primary fixed sheave until the belt is seated in
and both primary and secondary sheaves move together
smoothly without slip.
CVT Case Cover
Install the new gasket and dowel pins.

Install CVT case cover bolts and tighten diagonally

in several steps.
Engine Left
Oil Pump Sprocket and Chain
Install oil pump drive sprocket;
Install oil pump driven sprocket;
Install oil pump drive chain;
Install oil pump sprocket bolt;
Install sprocket retainer with a long nose pliers
Tool: Long Nose Pliers
Dual Gear, Idle Gear
Install dual gear shaft① and dual gear ②
Install dual gear shaft③, dual gear ④and bush⑤
Starting Driven Gear
Install starting driven gear bush⑥

Install starting driven gear;
Magneto Rotor
Install woodruff key into crankshaft groove;
Install magneto rotor 1;
Note: Degrease the tapered part of rotor and crankshaft.

Use nonflammable solvent to clean off the oily or greasy
matter and fully dry the surfaces.
Install Splined Spacer N°1;

Install Bolt N°2,
Bolt tightening torque: 60N.m;
Remove Bolt;
Remove Splined Spacer
Left Crankcase Cover
Install dowel pin2 and gasket 3
Note: Use a new gasket
Apply Lubricant grease to oil sea lip;
Install left crankcase cover N°1A
Install bolts;
Splined Spacer
Install splined spacer 1B / 2A
Install O-ring 2B
Note: Use a new O-ring and apply lubricant grease to

the O-ring
Install washer 3B and bolt 4B / 3A, tighten to the specified

torque:
Bolt tightening torque: 100N.m

Water Pump
Install water pump;
Install water pump fixing bolts;
Note: Before tightening the bolts, be sure to insert oil

pump shaft into groove of water pump shaft.
Sector Gear
Install the parts as illustrated on the right.
1- sector gear cover and gasket

2-dowel pin
3-drive sector gear
4-driven sector gear
5-driven sector gear bolt
Note: When the shift cam is in the neutral position, the

mark of drive sector gear should be between the two
marks of the driven sector gear.
Driven sector gear tightening torque: 14N.m

Oil Filter
Install oil filter bolt and tighten to the specified

torque;
Oil filter bolt tightening torque: 36 N·m
Apply engine oil to O-ring;
Install oil filter, turn it by hand until the filter gasket

contacts the mating surface. Tighten the bolts to the
specified torque.
Tool: Oil Filter Wrench
Starting Motor
Apply engine oil to new O-ring;
Install starting motor;
Install bolt and tighten to the specified torque
Tightening torque: 10N·m
Engine Top Side
Piston
Install the piston rings in the order of oil ring, ②ring
and ①ring.;
The first member to go into the oil ring groove is

spacer①, after placing the spacer, fit the two side
rails②.
Warning: when installing the spacer①, do not overlap its

two ends in the groove.
Install the second ring A and first ring B
Note: 1st ring and 2nd ring differ in shape

1st and 2nd rings have letter “R” marked on the side.
Be sure to bring the marked side to the top when
fitting them to the piston.
Position the gaps of the three rings as illustrated on

the right. Before installing the piston into the cylinder,
check that the gaps are so located.
Apply a light coat of moly oil to the piston pin;
Install piston pin into holes of piston and conrod

small end.
Note: When installing the piston, the “IN” mark on piston

top is located to the intake side.
Place a clean rag beneath piston and install piston

pin circlip ①
Note: while rotating crankshaft, pull the cam chain

upward, or the chain will be caught between sprocket
and crankcase.
Install the dowel pins and the new cylinder gasket;
Note: Use a new cylinder gasket to prevent oil leakage

Cylinder
Apply engine oil to piston skirt and cylinder wall;
Hold each piston ring with proper position, insert

piston into the cylinder;
Tighten the cylinder base bolts temporarily;
Note: When installing the cylinder and cylinder head,

pull the cam chain upward, or the chain will be caught
between sprocket and crankcase.
Install chain guide①;
Fit the dowel pin and new cylinder cover gasket;
Note: Use a new cylinder cover gasket to prevent oil

leakage
Cylinder Head
Install the cylinder cover, tighten the cylinder head

bolts diagonally to the specified torque.
Cylinder head bolt tightening torque: Initial: 25 N·m

Final: 40 N·m
Tighten the cylinder head nuts to the specified

torque;
Cylinder head nuts tightening torque:

M6: 10 N·m
M8: Initial 10 N·m
Final 25 N·m
Tighten the cylinder top nuts and cylinder base to

the specified torque;

Install chain tensioner;
Camshaft
Align mark “A” on magneto rotor with mark “B” on

crankcase;
Note: while rotating crankshaft, pull the cam chain

upward, or the chain will be caught between
sprocket and crankcase.
Align the mark “A” on the camshaft so that they are

parallel with the mating surface of the cylinder head.
Note: Do not rotate the magneto rotor while doing this.

when the sprocket is not positioned correctly, turn
the sprocket;
Engage the chain on the sprocket with the locating

pin “B” as illustrated on the right;
Recheck if the position of mark “A” and “C” is correct.

If not, reassemble until it is correct.

Install crankshaft C-ring ①
Install lock washer so that it covers the locating pin;
Apply thread locker to the bolts before installing, and

tighten them to the specified torque;
Sprocket bolt tightening torque: 15 N·m
Bend up the lock washer to lock the bolts.
Cylinder Head Cover
Clean the mating surface of cylinder head and

cylinder head cover;
Install dowel pin to the cylinder head
Apply sealant to the mating surface of the cylinder

head cover;
Install cylinder head cover bolts, tighten diagonally

to the specified torque.
Cylinder head cover bolt tightening torque: 10 N·m
Note: When tightening the cylinder head cover bolts,

the piston must be at top dead center on the
compression stroke.

Gasket Sealant Applying Place
Chain Tensioner
Insert (--) screwdriver into slotted end of chain

tension adjuster, turn it clockwise to lock the
tensioner spring;
Install the chain tensioner and the new washer 1;
Install the bolt 2, tighten it to the specified torque;
Chain tensioner bolt tightening torque: 10 N·m
After chain tensioner is installed, turn the (--)

screwdriver counter clockwise. The tensioner rod
will be advanced under spring force and push
tensioner against chain.

Install the new gasket 3;
Install chain tensioner screw, tighten it to the

specifiedTorque
Chain tensioner screw tightening torque: 8 N·m
Valve Adjuster Cover
Refer to 11-3 for valve clearance;
Use new rubber gasket and apply grease;
Install Valve Inspection Cap
Install valve inspection cap bolt;
Spark Plug
Install spark plug with special tool and tighten to the

specified torque;
Note: To avoid damage to the cylinder head thread,

screw in the spark plug with hand first, then
tighten it to the specified torque with spark plug
wrench.
Spark plug tightening torque: 18N.m

Tool: Spark Plug Wrench
Engine Periphery
Left Side Cover
Install left side cover
Install the bolts
Valve Inspection Cap
Install valve inspection cap

Water Pipe and Hose
Install water hose 5
Install bolt 4
Install water hose 3
Install clamp 1 and 2

3.6. Carburetor
Carburetor Removal…………………………………………………….…3.6.2
Inspection……………………………………………………………..….…3.6.3
.
Measurement and Adjustment…………………………………….………3.6.4
Carburetor Assembly………………………………………………………3.6.5
Carburetor Installation………………………………….……………….…3.6.6
Carburetor Parameters…………………… ……...…3.6.6

1. Carburetor Removal
Disassemble the carburetor in the following serial number:
Serial No. Description Qty. Serial No. Description Qty.

1 Idle Adjust Shaft 1 10 Drain Screw 1
2 Vacuum Chamber Cover 1 11 Float Chamber 1
3 Spring 1 12 Float 1
4 Jet Needle Holder 1 13 Needle Valve Set 1
5 Spring 1 14 Main Jet (MJ) 1
6 Jet Needle Set 1 15 Needle Jet (NJ) 1
7 Vacuum Diaphragm 1 16 Pilot Jet (PJ) 1
8 Piston Valve 1 17 Starter Jet (GS) 1
9 Enriching Diaphragm 1 18 Pilot Air Jet (PAJ) 1

2. Inspection
Check carburetor body for cracks or damage.
Cracks or damage:→ Replace
Check carburetor float chamber, fuel passage for

dirt or clog. Clean these parts.
Check float①, float tang ② for damage.
Damage: → Replace
Check valve seat①, needle valve②, O-ring③ for

damage, abnormal wear or dirt.
Damage or wear or dirty: → Replace
Note: Valve set①, needle valve② should be replaced as

a set.
Check piston valve① for scratches, abnormal wear

or damage.
Scratches, wear or damage: → Replace
Check diaphragm② for tears.
Tears: → Replace
Check vacuum chamber cover①, spring② for

damage or cracks.
Damage or cracks: → Replace

Check the diaphragm ① for tears;
Tears: → Replace
Check the spring ②,cover ③ for damage and tears;
Damage or tears: → Replace
Check the jet needle①, mail jet②, needle jet③, pilot

air jet④, pilot jet⑤, starter jet⑥ and starter plunger⑦
for wear and bends;
Wear or bends: → Replace
Check above jets for clog. Blow out the jets with
compressed air.
Insert piston valve into carburetor body and check

the free movement;
Check free movement of throttle valve. Replace with

a new one if it’s stuck;
3. Measurement and Adjustment
Keep the carburetor in a upside down position.

Measure distance “a” from the mating surface of
float chamber (without gasket) to the top of float.
Note: The float arm should rest on the needle valve. Do

not compress the needle valve.
Float Height: 10±1mm

If float height is not within the specification, check

the valve seat and needle valve;
If either of valve seat or needle valve is worn,

replace both;
If both are fine, adjust float height by bending the

float tang ①on the float;
Measure float height again till it’s within the

specification
Fuel Level
Place carburetor on a level surface. Connect fuel

level gauge① with drain pipe②;
Tool: Fuel Level Gauge

Loosen drain screw ③
Keep fuel level gauge vertical next to the float

chamber line and read the fuel level “a”
Fuel Level: 3.5±0.5mm
If the fuel level is not within the specification, adjust

the fuel level;
Remove carburetor
Check valve seat and needle valve
If either of valve seat or needle valve is worn,

replace both;
If both are fine, adjust float height by bending the

float tang ①on the float;
Install carburetor
Check again the fuel level
Carburetor Assembly
Reverse the disassembly procedure for assembly

Carburetor Installation
①-vacuum breather hose ②-starter cable ③-carburetor joint (engine intake manifold))
④-throttle valve cover ⑤-throttle cable ⑥-Carburetor joint (air filter) ⑦-carburetor
⑧-drain hose ⑨-fuel inlet hose
Note: Align the installation mark of carburetor and carburetor joint
6. Carburetor Parameters
Type MIKUNI BSR36-129

Aperture No. 07G0
Throat size (mm) 36mm
Pilot (r/min) 1400 r/min±100 r/min
Float height (mm) 10±1
Fuel level (mm) 3.5±0.5
Main jet (MJ) N102221-137.5#
Main air jet (MAJ) MD13/24-35#
Jet needle (JN) J8-5DH77
Needle jet (NJ) 785-401011-P-OM
Pilot jet (PJ) N224103-22.5#
Pilot screw (PS) 604-16013-1A
Pilot air jet1 (PAJ1) MD13/24-65#
Pilot air jet2 (PAJ2) N211100-165#

3.7. Cooling and Lubrication System
Engine Coolant………………………………………………………3.7.2
Inspection of Cooling Circuit……………………….………………3.7.2
Inspection and Cleaning of Radiator and Water Hoses…………3.7.3
Inspection of Fan Motor……………………………………….……3.7.4
Inspection of Water Temperature Sensor…………………………3.7.5
Inspection of Thermostat……………………………………………3.7.5
Water Pump……………………………………………………….…3.7.6
Water Pump Removal and Disassembly……………………3.7.6
Inspection………………………………………………………13.7.8
Water Pump Assembly and Installation………..……………3.7.9
Lubrication System Illustration………………………………..……3.7.13

Engine Coolant
The coolant used in cooling system is a 100% ethylene
glycol antifreeze.
Warning !
DO NOT open radiator cap when the engine is still
hot. Or you may be injured by scalding fluid or
steam;
Coolant is harmful. DO NOT swallow or stain your
skin or eyes with coolant. In case of accidental
swallow or stains, flush with plenty of water and
consult the doctor immediately.
Keep coolant away from reach of children.
Inspection of Cooling Circuit

Remove radiator cap① and connect tester ② to
filler.
Warning!
Do not open the radiator cap when the engine is still hot.
Give a pressure of 120 kPa and check if the cooling

system can hold this pressure for 10 seconds.
If the pressure drops during this 10 seconds, it

indicates that the there is leakage with the cooling
system. In this case, check the complete system
and replace the leaking parts or components.
Warning!
When removing the radiator cap tester, put a rag on
the filler to prevent splash of coolant.
Warning!
Do not allow a pressure to exceed the radiator cap
release pressure.

Inspection and Cleaning of Radiator and

Water Hoses
Radiator Cap
Remove radiator cap①
Install radiator cap to cap tester②
Slowly increase pressure to 110-140 kPa and

check if the cap can hold the pressure for at least
10 seconds.
If the cap cannot meet the pressure requirement,

replace it.
Radiator Cap Valve Opening Pressure:

Standard: 110-140 kPa
Tool: Radiator Cap Tester
Radiator Inspection and Cleaning
Remove dirt or trash from radiator with compressed

air;
Correct the radiator fins with a small screwdriver;
Radiator Hose Inspection
Check radiator hoses for leakage or damage.
Leakage or Damage: → Replace
Check tightening of clamps. Replace the clamps if

necessary;
After inspection and cleaning of radiator and hoses,

check coolant level. Fill coolant if necessary.

Inspection of Fan Motor
Remove fan motor from radiator
Turn the vanes and check if they can turn smoothly;
Check fan motor: Make sure that the battery applies

12 volts to the motor and the motor will run at full
speed while the ammeter shall indicate the ampere
not more than 5A.
If the motor does not run or the ampere exceeds the
limit, replace the motor.
Installation: Apply a little thread locker to the bolts

and tighten to the specified torque.
Fan Motor Bolt Tightening Torque: 10N.m
Inspection of Thermoswitch
Remove thermoswitch
Check the thermoswitch for closing or opening by
testing it at the bench as illustrated. Connect the
thermoswitch① to the circuit tester, place it in a
vessel with engine oil. Place the vessel above a
stove.
Heat the oil to raise the temperature slowly and take
the reading from thermometer ② when the
thermoswitch closes and opens.
Tool: ammeter
Thermoswitch Operating Temperature
Standard: (OFF-ON): Approx. 88℃
(ON-OFF): Approx. 82℃
Note:
Avoid sharp impact on thermoswitch.
Avoid contact of thermoswitch with thermometer or
vessel
Installation: Use a new O-ring③ and tighten the
thermoswitch to the specified torque:
Thermoswitch Tightening Torque: 17N.m
Check coolant level after installation of

thermoswitch. Fill coolant if necessary.

Inspection of Water Temperature Sensor
Place a rag under water temperature sensor① and

remove it from cylinder head.
Check the resistance of water temperature sensor

as illustrated on the right. Connect the temperature
sensor② to the circuit tester, place it in a vessel
with engine oil. Place the vessel above a stove.
Heat the oil to raise the temperature slowly and take
the reading from thermometer ③ and ohmmeter ④ .
Water Temperature and Resistance
Temperature(℃) 50 80 100 120

Resistance(Ω) 154±16 52±4 27±3 16±2
Installation: Apply a little thread locker and install it to

the cylinder head by tightening to the specified torque.
Water Temperature Sensor

Tightening Torque: 10N.m
Note:
Avoid sharp impact on temperature sensor
Avoid contact of temperature sensor with
thermometer or vessel
After installation, check the coolant level. Fill

coolant if necessary.
Inspection of Thermostat
Remove thermostat case
Remove thermostat

Check thermostat pellet for cracks

Test the thermostat in the following steps:
Pass a string between thermostat flange as

illustrated on the right;
Immerse the thermostat in a beaker with water.
Make sure that the thermostat is in the suspended
position without contact to the vessel. Heat the
water by placing the beaker above a stove and
observe the temperature rise on a thermometer;
Take the temperature reading from thermometer
when the thermostat valve opens.
Thermostat Valve Opening Temperature: 68-74℃
Keep heating the water to raise the water

temperature.
Just when the water temperature reaches the

specified value, the thermostat valve should have
been lifted by 3.5-4.5mm
Installation:
Apply coolant to the rubber seal of thermostat.
Install thermostat case. Tighten to the specified

torque:
Tightening Torque: 10N.m
Water Pump
Removal and Disassembly
Drain coolant (→11-10)
Note: Before draining coolant, check water pump for oil

or coolant leakage. In case of oil leakage, check the
water pump oil seal, O-ring. In case of coolant leakage,
check the water seal.

Remove clamps and water hoses
Release bolts and remove water pump
Remove O-ring
Note: Do not reuse the O-ring.
Remove the overflow tube
Release water pump cover screws, water pump

cover and gasket
Remove E-ring and impeller
Remove seal ring ①and rubber seal②

Remove mechanical seal with special tool
Note: The mechanical seal does not need to be

removed if there is no abnormal condition.
Note: Do not reuse a removed mechanical seal
Put a rag on the water pump body
Remove oil seal.
Note: The oil seal does not need to be removed if there

is no abnormal condition
Note: Do not reuse a removed oil seal
Remove bearing with special tool.
Note: The bearing does not need to be removed if

there is no abnormal noise.
Note: Do not reuse a removed bearing.
Inspection of Water Pump
Bearing
Check the play of bearing by hand while it is still in

the water pump body;
Turn inner race of bearing to check for abnormal
noise and smooth rotation;
Replace the bearing if there is abnormal condition;
Mechanical Seal
Check mechanical seal for damage, pay special

attention to the seal face;
In case of leakage or damage, replace the
mechanical seal. If necessary, also replace the seal
ring.

Oil Seal
Check oil seal for damage. Pay special attention to

the oil seal lip;
In case of damage or leakage, replace the oil seal;
Water Pump Body
Check the mating mace of water pump body with

bearing and mechanical seal.
Damage: →Replace
Impeller
Check the impeller and shaft for damage.

Damage: →Replace
Assembly and Installation of Water Pump
Install oil seal with special tool;
Tool: Oil Seal Installer
Note: The stamped mark on the oil seal faces outside
Apply a little grease to the oil seal lip.

Install mechanical seal with a suitable socket

wrench
Note: Apply sealant to side “A” of mechanical seal
Install bearing with special tool
Tool: Bearing Installer
Note: The stamped mark on the bearing faces outside.
Install seal ring to impeller
Clean off the oil and grease from mechanical seal

and install it into the impeller.
Note: “A” side of mechanical seal faces impeller
Apply grease to impeller shaft
Install impeller shaft to water pump body.

Install E-ring to water pump shaft;
Install new gasket to water pump body;
Install water pump cover and tighten the bolts and

bleed bolt.
Water Pump Cover Bolts Tightening Torque: 6N.m
Check impeller for smooth turning.
Install the new O-ring
Note:
Use the new O-ring to prevent oil leakage;
Apply grease to O-ring

Install water pump and tighten the bolts to the

specified torque;
Water pump bolts tightening torque: 10N.m
Note: Set the water pump shaft slot end “B” to oil pump
shaft flat side “A”.
Connect water hoses
Add coolant


1. Engine
Complaint Symptom and Possible Causes Remedy
Compression is Too Low
1. Worn cylinder Replace
2. Worn piston ring Replace
3. Leakage with cylinder gasket Replace
Wear valve guide or improper valve Repair or Replace
seating
4. Loose spark plug Tighten
5. Slow cranking of starting motor Check electrical part
6. Faulty valve timing Adjust
Engine will not 7. Improper valve clearance Adjust
No Sparking from Spark Plug

Clean or Replace
start of is hard to 1. Fouled spark plug
start 2. Wet spark plug Clean and dry or replace
3. Defective ignition coil Replace
4. Open or short circuit with pickup coil Replace
5. Faulty generator Replace
6. Faulty CDI Replace
No Fuel Reach Into Carburetor

Clean or Replace
1. Clogged fuel tank vent tube
2. Clogged or faulty fuel valve Clean or Replace
3. Faulty carburetor needle valve Replace
4. Clogged fuel hose Replace
5. Clogged fuel filter Clean or Replace
Transfer is not in Neutral position Set to Neutral position
1. Improper valve clearance Adjust
2. Improper valve seating Replace or Correct
3. Faulty valve guide Replace
4. Worn rocker arm or rocker arm shaft Replace
5. Fouled spark plug Replace
Engine stalls easily 6. Improper spark plug gap Replace or Adjust
7. Faulty ignition coil Replace
or has unstable 8. Faulty CDI Replace
idle speed 9. Faulty generator Replace
10. Improper fuel level in float chamber Adjust Fuel level
11. Clogged carburetor jet Clean
12. Faulty fuel valve Replace
13. Improper adjustment or idle screw Adjust

3.8. Troubleshooting
1. Week valve spring Replace
2. Worn camshaft Replace
3. Fouled spark plug Clean or replace
4. Insufficient spark plug gap Adjust or replace
Poor engine
5. Improper valve timing Replace
running in 6. Faulty ignition coil Adjust float chamber fuel level
high-speed range. 7. Low fuel level in float chamber Clean or replace
8. Dirty air filter Clean
9. Clogged fuel hose, resulting in poor fuel Clean
supply
10. Clogged fuel valve Clean
1. Excessive engine oil Check oil level and drain

Exhaust smoke is 3. Worn valve guide Replace
4. Scored or scuffed cylinder wall Replace
dirty or thick
5. Worn valve stem Replace
6. Worn valve stem oil seal Replace
1. Improper valve clearance Adjust

2. Weak valve spring Adjust
3. Improper valve timing Adjust
Engine lacks 6. Improper valve seating Replace or Correct
7. Fouled spark plug Clean or replace
power 8. Improper spark plug gap Clean or replace
9. Clogged carburetor jet Clean or replace
10. Improper fuel level in fuel chamber Adjust fuel level
11. Dirty air filter Clean or replace
12. Worn rocker arm or rocker arm shaft Replace
13. Air leakage from air intake pipe Tighten or replace
14. Excessive engine oil Check oil level and drain
1. Carbon deposit on piston top Clean

2. Insufficient or excessive engine oil Check level, add or drain
3. Faulty oil pump Replace
Engine 4. Clogged oil passage Clean
5. Fuel level in float chamber is too low Adjust fuel level
overheats
6. Air leakage from air intake pipe Tighten or replace
7. Incorrect engine oil Change engine oil
8. Faulty cooling system (→16-5)

Valve Chatter
1. Excessive valve clearance Replace
2. Worn or broken valve spring Replace
3. Worn rocker arm or camshaft Replace
Noise from Piston

1. Worn piston Replace
3. Carbon deposit in combustion chamber Clean
4. Worn piston pin or pin hole Replace
5. Worn piston ring or piston ring groove Replace
Noise from Timing chain

1. Stretched chain Replace chain & sprocket
Engine is
2. Worn sprocket wheel Replace chain & sprocket
3. Faulty chain tensioner Repair or replace
Noise from Clutch

noisy 1. Worn or damaged crankshaft spline Replace crankshaft
2. Worn inner race spline Replace inner race
Noise from Crankshaft

1. Rattling bearing Replace
2. Worn or burnt crank pin bearing Replace
3. Excessive thrust clearance Replace
Noise from CVT

1. Worn or slipping drive belt Replace
2. Worn rollers in primary sheave Replace
Noise from Transmission

1. Worn or damaged gear Replace
2. Worn or damaged input or output shafts Replace
3. Worn bearing Replace
4. Worn bushing Replace
1. Worn or damaged clutch shoes Replace

Slipping 2. Weakened clutch shoe spring Replace
3. Worn clutch housing Replace
Clutch
4. Worn or slipping drive belt REplace


Difficulty or locked 1. Broken drive or driven bevel gear teeth Replace
gearshift 2. Distorted shift fork Replace
3. Worn shift cam Replace
4. Improper gearshift rod Adjust
2. Carburetor
1. Clogged starter jet Clean
2. Clogged starter jet passage Clean
Starting Difficulty
3. Air leakage from joint between starter body Clean, adjust or replace gasket
and carburetor
4. Faulty starting plunger Adjust
1. Clogged slow jet Clean
2. Clogged slow jet passage Clean
Idling or 3. Clogged air intake Clean
4. Clogged bypass port Clean
low-speed
5. Starter plunger not fully closed Adjust
trouble
6. Improper set of idle screw Adjust
7. Improper float height Adjust
1. Clogged main jet Clean

2. Clogged main air jet Clean
Medium or high 3. Clogged needle jet Clean
4. Faulty throttle valve Adjust
speed trouble
5. Clogged fuel filter Clean
6. Improper float height Adjust
7. Starter plunger not fully closed Adjust
Overflow and fuel 1. Worn or damaged needle valve Replace
level fluctuation 2. Damaged needle valve spring Replace
3. Improper working float Adjust or Replace
4. Foreign matter in needle valve Clean

3. Cooling System/Radiator
1. Clogged water passage or radiator Clean

2. Air in the cooling system; insufficient Discharge air and add coolant
coolant
Engine overheats
3. Faulty water pump Check and replace
4. Incorrect coolant Replace
5. Faulty thermostat Replace
6. Faulty fan motor or thermoswitch Check and/or replace
1. Faulty thermoswitch Replace
Engine coolant
2. Extremely cold weather Put on radiator cover
overcools 3. Faulty thermostat Replace
4. Ignition System

1. Faulty CDI Check and replace
2. Faulty spark plug Check and replace
No Sparking or 3. Faulty Generator Check and replace
4. Insufficient battery voltage Check and replace
Weak Sparking 5. Faulty ignition coil Check and replace
6. Faulty pickup coil Check and replace

NOTES

CHAPTER 4A CHASSIS LH500ATV-D SERVICE MANUAL 14.0
CHAPTER 4 CHASSIS
ATV 500
WARNING
4.1 A-RM REPLACEMENT
4.2 SWING ARM
4.3 FRONT STRUT REPLACEMENT
4.4 FRONT STRUT BALL JOINT REPLACEMENT
4.5 STEERING POST ASSEMBLY
CHAPTER 4 CHASSIS PAGE. 4- 1

4.1 A-RM REPLACEMENT (MacPherson)
MANTENANCE-FREE PIVOT DESIGN
1. Elevate and safely support vehicle

2. Remove cotter pin from ball joint cup at wheel end of A- arm and loosen nut until it is
flush with end of cup.
3. Using a soft face hammer, tap nut to loosen A- arm from bolt. Remove nut and A-arm
from hub strut assembly.
4. Loosen and remove two bolts on A-arm, and remove A-arm.
5. Examine bushing. Replace if worn or tore. Discard hardware.
6. Install new A-arm assembly onto vehicle frame. Install new bolts and new nuts.
NOTE. Tighten the nuts only finger-tighten at this time. They will be tightened to the final
torque after the front wheels are installed and the vehicle is on the ground.
WARNING
DO NOT reuse old bolts. Serious injury or death could result if fasteners come loose during
operation.
7. Attach A-arm to strut assembly. Tighten ball joint nut to 25 ft. lbs. (35 Nm). If cotter pin
holes are not aligned, tighten nut slightly to align. Install a new cotter pin with open ends
toward rear of machine. Bend both ends in opposite directions around nut.
8. Install hubs, calipers and wheels, lower the vehicle to the ground. Apply Loctite™ 242 to
screw threads of the A arm bolts and torque bolts to 37-44 ft. lbs. (50-60 Nm ).
WARNING
Upon A-arm installation completion, test vehicle at low speeds before putting into regular
service.
4.3 FRONT STRUT REPLACEMENT ATV500

1. Hold strut rod with
wrench and remove top
nut
2. Compress spring.
3. Remove upper strut pivot
assembly.
4. Remove coil spring and
collapse strut body.
5. Remove two pinch bolts
from strut body.
6. Remove strut body.
7. Install front shock
cartridge until bottomed
in strut casting.
8. Install pinch bolts with
clamp(s).
Torque pinch bolts to
15ft.lbs.(21Nm).
9. Reassemble spring and
top pivot assembly. Be
sure all parts are
installed properly and
seated fully.
10. Torque strut rod nut to
specification. Do not
over torque nut.
Strut Rod Nut Torque
15 ft. lbs. (21 Nm)

4.4 FRONT STRUT BALL JOINT REPLACEMENT ATV500

1. Loosen front wheel nuts.
2. Elevate and safely support ATV under
footrest/frame area. .
CAUTION: Serious injury may result if
ATV tips or falls. Be sure ATV is secure
before beginning this service procedure.
3. Remove wheel nuts and wheels.
4. Remove cotter pin from ball joint
5. Remove castle nut and separate A-
arm from ball joint stud.
6. Remove screws and ball joint mounting
bracket.
7. Using ball joint cup removal/installation
toolkit, remove ball joint cup from strut
housing. Refer to photos at right.
zInstall puller guide (1) .
zThread bolt (2) with nut (3) onto bal
joint stud as shown .
zHold bolt (2) and turn nut (3)
clockwise until ball joint is removed
from strut housing.
8. To install new ball joint cup.
zInsert new ball joint into driver
(installation toolkit).
zDrive new bal joint cup into strut
housing until fully seated.
9. Apply Loctite 242 (blue) to threads of
mounting bracket new screws.
Torque screw s to 8 ft.lbs. (11 Nm).
10. Install A- arm on bal joint cup and
torque castle nut to 25 ft. lbs. (35
Nm ).
11. Reinstall cotter pin with open ends
toward rear of machine.

4.5 STEERING POST ASSEMBLY
Note:
1, Hand tighten the crown nut of the steering post.
2, Align cotter pin hole.
3, Install cotter pin. Bend both ends of cotter pin around nut in opposite directions.
4, Check steering, must move freely and easily from full left to full right without binding.

NOTES

CHAPTER 5 FINAL DRIVE LH500ATV-D SERVICE MANUAL 14.0
CHAPTER 5 FINAL DRIVE

ATV500
WARNING
(PLEASE SEE CHARPTER 4B IN THIS MANUAL FOR THE WHEEL, HUB, AND DRIVE
C H A I N O F M I N E / Y O U T H AT V )
5.1 WHEEL, HUB, AND SPINDLE TORQUE TABLE
5.2 FRONT HUB DISASSEMBLY/INSPECTION
5.3 FRONT HUB ASSEMBLY
5.4 FRONT HUB INSTALLATION (2WD)
CHAPTER 5 FINAL DRIVE. 5- 1

5.1 WH E E L , H U B , AND SPINDLE TORQUE TABLE
Item Specification
Front Wheel Nuts 69 Ft.Lbs 96 N.m
Rear Wheel Nuts 69 Ft.Lbs 96 N.m
Front Hub Nut on Spindle/ outer CV joint Refer to FRONT HUB INSTALLATION
Rear Hub Retaining Nut 101Ft.Lbs 137N.m
CAUTION: Locking nuts, and bolts with pre-applied locking agent should be replaced if
removed. The self- locking properties of the nut or bolt are reduced or destroyed during removal.
5.2 FRONT HUB DISASSEMBLY/INSPECTION
1. Elevate front end and safely support

machine under footrest/frame area.
CAUTION
Serious injury may result if machine tips
or falls. Be sure machine is secure
before beginning this service procedure.
Wear eye protection when removing
bearings and seals.
2. Check bearings for side play by grasping
tire/wheel firmly and checking for
movement. It should rotate smoothly
without binding or rough spots.
3. Remove wheel nuts and wheel.
4. Remove brake caliper
5. Remove hub cap, cotter pin, front
spindle nut, and washer.
6. Rotate each bearing by hand and check for
smooth rotation. Visually inspect bearing
for moisture, dirt, or corrosion. Replace
bearing if moisture, dirt, corrosion, or
roughness is evident.

7. Place a shop towel on hub to protect

surface. Carefully pry seal out of hub. Do
not damage the surface of the seal. Clean
the hub.
8. Drive bearing out through opposite side of
hub and discard.
9. Drive other bearing out and discard.
10. Clean hub and spacer thoroughly.
5.2 FRONT HUB REMOVAL/INSPECTION 4x4(ATV500)
1. Elevate front end and safely support

machine Under footrest/frame area.
CAUTION:
Serious injury may result if machine tips or
falls, Be sure machine is secure before
beginning this service procedure. Wear
eye protection when removing bearings
and seals.
2. Check bearings for side play by grasping
the tire/Wheel firmly and checking for
movement. Grasp The top and bottom of
the tire. The tire should rotate smoothly
without binding or rough spots.
3. Remove wheel nuts and wheel.
4. Remove the two brake caliper attaching
bolts.
CAUTION:
Do not hang the caliper by the brake
Line. Use wire to hang the caliper to
prevent. Possible damage to the brake
line.
5. Remove hub cap, cotter pin, front spindle
nut, and Washer.

6. Rotate each bearing by hand and check

for smooth rotation. Visually inspect
bearing for moisture, dirt, or corrosion, or
roughness is evident.
5.3 b. FRONT HUB INSTALLATION 4X4 (ATV500)
1. Inspect the hub strut bearing surface for

wear or damage.
2. Apply grease to drive axle spindle.
3. Install spindle through the backside of the
hub strut. Install the hub onto the spindle.
4. Install spindle nut and tighten to
specification.
5. Install a new cotter pin. Tighten nut slightly
if necessary to align cotter pin holes.
6. Rotate wheel and check for smooth
operation. Bend both ends of cotter pin
around end of Spindle in different
directions.
7. Install hub cap.
8. Rotate hub. It should rotate smoothly
without binding or rough spots or side play.
9. Install brake caliper using new bolts.
Tighten bolts to specified torque.
CAUTION: New bolts have a pre-applied

locking. agent which is destroyed upon
removal. Always use new brake caliper
mounting bolts upon assembly.

10. Install wheel and wheel nuts and tighten

evenly in a cross pattern to specified
torque.
5.4 b. FRONT HUB BEARING REPLACEMENT 4X4 (ATV500)

1. Remove outer snap ring.
2. Form the back side, tap on the outer
bearing race with a drift punch in the relief
as shown.
3. Drive bearing out evenly by tapping on
outer race only. Once bearing is at bottom
of casting, support casting on outer edges
so bearing can be removed.
4. Inspect bearing.
NOTE: Due to extremely close tolerances

and minimal wear, the bearings must be
inspected visually, and by feel. inspect for
rough spots, discoloration, The bearings
should turn smoothly and quietly, no
detectable up and down movement and
minimal movement sideways between inner
and outer race.
5. Inspect bearing housing for scratches,
wear or damage. Replace housing if
damaged.

5.5 FRONT DRIVE AXLE (INNER AND OUTER CV JOINT) REMAVAL/
INSPECTION (4X4)
NOTE
The outer CV joint cannot be disassembled or repaired, if damage or faulty the drive axle
assembly must be replace.
1. Drive axle/ outer CV joint assembly.
2. Boot band “A”.
3. Outer board boot.
4. Boot band “B”.
5. Stopper ring
6. Outer CV joint *
7. Circlip
8. Bearing *
9. stopper ring
10. Inboard boot.
NOTE: Always order and replace 6 and 8 together.
REMOVAL
1. Place the vehicle on level ground and set
the parking brake, Block the rear wheels so
the vehicle will not roll in either direction.
2. Remove the front wheels, steering tie rods,
disconnect the A arm on the ball joint end
as described in this Chapter and Chapter
4.
CAUTION
To avoid damage to the front differential
oil seal, hold the front drive shaft
horizontal and straight out from the front
differential during removal.

3. Hold the drive shaft straight out.

4. Place a tire lever between the inner CV
joint and the differential housing, with a
small piece of wood against the housing to
help get "leverage" and protect the casting.
"pop" the in inner CV joint out from the front
differential.
INSPECTION
NOTE The boots are subjected to a lot of
abuse if the vehicle is ridden in rough
terrain. If the boots are damage and left
un-repaired, the driveshaft joints will fair
prematurely by allowing the joint to be
exposed to dirt, mud and moisture. This
also allow the loss of critical lubrication.
1. Check the rubber boots for wear, cuts or
damage and replace if necessary as
described under the Disassembly /
Assembly procedure in this chapter.
2. Move each end of the drive shaft in a
circular motion (and also a reciprocate for
inner one) and check the drive shaft joints
for excessive wear or play.
3. This inner CV joint (inboard pivot joint) can
be serviced if there is wear or play. The
outer CV joint (outboard pivot joint) cannot
be serviced if worn or damage and if
necessary, the drive shaft assembly must
be replaced.
5.6 FRONT DRIVE AXLE INSTALLATION (4X4)
CAUTION
To avoid damage to the front differential
oil seal and the strut oil seal, hold the
front drive shaft horizontal and straight
into the strut during installation.
1. Hold the drive shaft straight in from the
front differential.
2. Push the drive shaft straight into the front
differential and push it in all the way until it
bottoms out. If necessary, carefully tap on
the outer end of the drive shaft with a
rubber mallet or soft-faced mallet.

3. After the drive shaft is installed, pull the

inner CV joint a little to make sure the
drive shaft stopper ring has locked into the
front differential side gear groove.
4. Carefully install the outer CV joint
(spindle) into the strut，install the front hub
and wheel.
5. Install the ball joint on the A arm, the
steering tie rods, the hubs and the wheels
as described in this Chapter and Chapter
4.
5.7 FRONT DRIVE AXLE DISASSEMBLY/ INSPECTION (4X4)

INNER CV JOINT DISASSEMBLY
NOTE
The outer CV joint cannot be
disassembled or repaired, if damage
or faulty the drive axle assembly must
be replace.
1. Open the clamps on both boot band“A”
and“B”on the inner CV joint, then remove
boot band“B”.Discard the boot band, it

cannot be reused.
2. Carefully slide the boot (A) onto the drive
axle and off the inboard joint.
3. Wipe out all of the molybdenum disulfide Remove the stopper ring
grease within the inboard joint cavity.
4. Remove the stopper ring from the inboard
joint. Inspect groove
5. Remove the inner CV joint.
6. Remove the circlip and slide off the
bearing assembly. Be careful not to drop
any of the steel balls from the bearing
cage.
7. slide the inner CV off the drive axle and
discard the boot band“A”， it cannot be
reused.

8. If the outboard boot requires replacement,

perform the following:
a. Open the clamps on both boot bands
“A”and“B” on the outer CV joint, then
remove boot band“B”.Discard the boot

band, it cannot be reused.
b. Slide the outboard boot off the drive
axle and discard the boot band“A”, it
cannot be reused.
9. Inspect the drive axle as described in this
chapter.
INNER CV JOINT INSPECTION
1. Clean the bearing assembly in solvent
and thoroughly dry.
2. Inspect the steel balls, bearing case and
the bearing race for wear or damage.
3. Check for wear or damage to the inner
splines of the bearing race.
4. If necessary, disassembly the bearing
assembly for further inspection. Carefully
remove the steel balls from the bearing
cage then remove the bearing race from
the bearing cage.
5. If any of the components of the bearing
assembly are damaged, replace the entire
assembly as no replacement parts are
available.
6. Clean the inner CV joint in solvent and Check the movement of the joint
thoroughly dry.
7. Inspect the interior of the inboard joint
where the steel balls ride. Check for wear
or damage and replace the joint if
necessary.
8. Inspect the snap ring groove on the
inboard joint for wear or damage.
9. Inspect the splines on the inner CV joint
for wear or damage.
10. Check the stopper ring in the end of the
inboard joint. Make sure it seats in the
groove correctly, if damage the ring must
be replaced.

11. Inspect the exterior of the inner CV joint

for cracks or damage, replace if
necessary. Check the movement of the
joint for excessive play or noise by moving
the drive axle in a circular and reciprocate
direction.
12. Inspect the drive axle for bending, wear or
damage.
13. Inspect the inner end splines, the outer NOTE. Inner CV joint must be replaced with the
end splines and the front hub cotter pin bearing as an assembly.
hole for wear or damage. If any of these
areas are worn or damaged, replace the
drive axle.
5.8 FRONT DRIVE AXLE ASSEMBLY (4X4)

1. The rubber boots are not identical and
must be installed on the correct joint. The
boots are marked as follows:
a. Inner CV joint boot : “inner”,
b. Outer CV joint boot: “outer”.
2. IF the outboard boot was removed, install
a new boot onto the drive axle at this time.
NOTE
Position the new boot bands with their
tabs facing toward the rear of the
vehicle.
3. Install 2 new small boot bands onto the
drive axle.
4. Install the inboard boot and move the
small boot band onto the boot. Bend down
the tab on the boot band and secure the
tab with the locking clips and tap them
with a plastic hammer. Make sure they are
locked in place.
5. If the bearing assembly was
disassembled, assemble the bearing as
follows:
a. Position the bearing race and install
the race into the bearing case. Align
the steel ball receptacles in both
parts.
b. Install the steel balls into their
receptacles in the bearing case.

c. Pack the bearing assembly with

molybdenum disulfide grease. This will
help hold the steel balls in place.
6. Position the bearing assembly with the
small end of the bearing going on first and
install the bearing onto the drive axle.
7. Push the bearing assembly on until it
stops, then install the circlip, Make sure
the circlip seats correctly in the drive axle
groove.
8. Apply a liberal amount of molybdenum
disulfide grease to the bearing assembly.
Work the grease in between the balls, the
race and the case. Make sure all voids are
filled with grease.
9. Apply a liberal amount of molybdenum
disulfide grease to the inner surfaces of
the inboard joint.
10. Install the inboard joint over the bearing
assembly and install the stopper ring.
Make sure it is seated correctly in the
inboard joint groove.
11. After the stopper ring is in place, fill the
inboard joint cavity behind the bearing
assembly with additional molybdenum
disulfide grease.
12. Pack each boot with the following
amounts of molybdenum disulfide grease:
a. Inboard boot:35-55grams(1.2-1.9oz.).
b. Outboard
boot:30-50grams(1.1-1.8oz.).
13. Move the inboard boot onto the inner CV
joint.
14. Move the inboard joint on the drive axle.
NOTE
Position the new boot bands with their
tabs facing toward the rear of the
vehicle .
15. Move the small boot band onto the boot.
Bend down the tab on the boot band and
secure the tab with the locking clips and
tap them with a plastic hammer. Make
sure they are locked in place.

16. Install the large boot bands onto each

boot.
CAUTION
It is critical to avoid undue stress on the
rubber boots after the drive axle is
installed and the vehicle is run. Don’t
twist the boot, and always set the both
ends in designed position.
17. Secure all large boot bands. Bend down
the tab on the boot band and secure the
tab with the locking clip and tap them with
a plastic hammer. Make sure they are
locked in place.
18. If removed, install the stopper ring and
make sure it is seated correctly in the
drive axle groove.
19. Apply molybdenum disulfide grease to the
end splines.
5.9 REAR HUB INSPECTION
1. Remove rear wheel.

2. Remove the cotter pin on the rear wheel driving shaft nut, than remove the nut.
3. Remove the rear disc brake caliper.

4. Remove the link, RR. Stabilizer.

5. Remove the mounting bolt of rear shock absorber and upper and lower A-arm. Takedown the
A-arm components.
6. Remove the mounting bolt of the rear hub, after that inspect bushes, A-arms and collar.
Replace if worn. Discard hardware.
7. Using hub extractor to take down the rear hub.

8. Remove oil seal.

9. Remove the snap spring of the rear hub.

10. Using bearing extractor to take down the hub bearing.
Notice: when reassembling hub bearing that were removed and rear hub, which are need
replaced. (The method is in accordance with removing steering knuckle.)

NOTES

CHAPTER 6 BRAKES LH500ATV-D SERVICE MANUAL 14.0
CHAPTER 6 BRAKES
NOTE
Also See Chapter 2 for Maintenance Information.
6.1 SPECIFICATIONS
6.2 TORQUE
6.3 BRAKE SYSTEM SERVICE NOTES
6.4 BURNISHING PROCEDURE
6.5 FLUID REPLACEMENT/BLEEDING PROCEDURE
6.6 HAND BRAKE MASTER CYLINDER REMOVAL/ INSPECTION /INSTALLATION
6.7 FRONT PAD REMOVAL / INSPECTION / INSTALLATION
6.8 FRONT DISC INSPECTION / REMOVAL / REPLACEMENT
6.9 FRONT CALIPER REMOVAL/ INSPECTION / INSTALLATION
6.10 REAR BRAKE PAD REMOVAL/ INSPECTION / INSTALLATION
6.11 REAR CALIPER REMOVAL/ INSPECTION/ INSTALLATION
6.12 REAR BRAKE DISC INSPECTION / REMOVAL / REPLACEMENT
CHAPTER 6 BRAKES PAGE. 6- 1

6.1 SPECIFICATIONS
Front Brake Caliper
Item Standard Service Limit
Brake Pad Friction material
0.157"/ 4mm 0.04"/ 1mm
Thickness
0.150- 0.164"/3.810- 4.166m
B rake Disc Thickness 0.140"/3 .556m m
m
Brake Disc Thickness Variance
- 0.002 "/ .051m m
Between Measurements
Brake Disc Runout - 0.005 "/ .12 7m m
Rear Brake Caliper
Item Standard Service Limit
Brake Pad hydraulic 0.157"/ 4mm
Friction Hydraulic with
0.236"/ 6mm 0.04"/ 1mm
material mechanics park
Thickness mechanics park 0.197"/ 5mm
Brake Disc Thickness 0.177-0.187"/4.496-4.750m m 0.167"/4.242mm
Brake Disc Thickness
Variance - 0.002 "/ 0.051m m
Between Measurements
Brake Disc Run out - 0.005 "/ 0.12 7m m
6.2 TORQUE
Torque Torque
Item
(ft. lbs. except where noted*) (Nm )
Front Caliper Mounting Bolts 18.0 25
Rear Caliper Mounting Bolts 18 .0 25
Master Cylinder Mounting Bolts *55 in. lbs 6.0
Master Cylinder Reservoir Cover Bolts *5 in. lbs .6
Hand Brake Hose Banjo Bolt 15 .0 21
Front Brake Disc 18 .0 25
Front Wheel Mounting Nuts 20 .0 27
6.3 BRAKE SYSTEM SERVICE NOTES

zIt is strongly recommended always change the caliper and (or) the master cylinder as an
assembly. The parts inside maybe not interchangeable due to different brake manufactures
and (or) different brake type.
zDo not over – fill the master cylinder fluid reservoir.
zMake sure the brake lever and pedal returns freely and completely.

zCheck and adjust master cylinder reservoir fluid level after pad service.
zMake sure atmospheric vent on reservoir is unobstructed.
zAdjust foot brake after pad service.
zTest for brake drag after any brake system service and investigate cause if brake drag is
evident.
zMake sure caliper moves freely on guide pins (where applicable) .
zInspect caliper piston seals for foreign material that could prevent caliper pistons from
returning freely.
zPerform a brake burnishing procedure after install new pads to maximize service life.
6.4 BURNISHING PROCEDURE

Brake pads (both hydraulic and mechanical) must be burnished to achieve full braking
effectiveness. Braking distance will be extended until brake pads are properly burnished. To
properly burnish the brake pads, use the following procedure.
1. Choose an area large enough to safely accelerate the ATV to 50 km/h (30 mph ) and to brake
to a stop.
2. Using hi gear, accelerate to 50 km/h (30 mph); then compress brake lever (pedal) to
decelerate to 0-8km/h (5 mph).
3. Repeat procedure on each brake system 20 times until brake pads are burnished.
(4. Adjust the mechanical parking brake (if necessary).)
5. Verify that the brake light illuminates when the hand lever is compressed or the brake pedal is
depressed.
WARNING
Failure to properly burnish the brake pads could lead to premature brake pad wear or brake loss.
Brake loss can result in severe injury.
6.5 FLUID REPLACEMENT/BLEEDING PROCEDURE

NOTE : When bleeding the brakes or
replacing the fluid always start with the caliper
farthest from the master cylinder.
CAUTION
Always wear safety glasses.
CAUTION
Brake fluid is highly corrosive. Do not spill
brake fluid on any surface of the ATV.

BRAKE BLEEDING-FLUID CHANGE
This procedure should be used to change fluid

or bleed brakes during regular maintenance.
1. Clean reservoir cover thoroughly.
2. Remove screws, cover and diaphragm
from reservoir.
3. Inspect vent slots in cover and remove any
debris or blockage.
4. If changing fluid, remove old fluid from
reservoir with a brake fluid pump or
similar tool.
NOTE: Do not remove brake lever when
reservoir fluid level is low.
5. Add brake fluid up to the indicated MAX
level on the reservoir.
6. Begin bleeding procedure with the caliper
that is farthest from the m aster cylinder.
Install a box end wrench on the caliper
bleeder screw. Attach a clean, clear hose
to the fitting and place the other end in a
clean container. Be sure the hose fits
tightly on the fitting.
NOTE: Fluid may be forced from supply port
when brake lever is pumped. Place
diaphragm in reservoir to prevent spills. Do
not install cover.
DOT 3 Brake Fluid
Reservoir Cover Torque

5 in. lbs. (.6 Nm )
7. Slowly pump brake lever (D) until
pressure builds and holds.
8. While maintaining lever pressure, open
bleeder screw. Close bleeder screw and
release brake lever.
NOTE: Do not release lever before bleeder
screw is tight or air m ay be draw n into
caliper.
NOTE: In some versions of brake, there are 2
hydraulic circulates in one caliper for foot
brake and hand brake. Make sure you bleed
the right circulate.
9. Repeat procedure until clean fluid

appears in bleeder hose and al air has
been purged. Add fluid as necessary to
maintain level in reservoir.
CAUTION:
Maintain at least 1/2 " (13mm of brake fluid in
the reservoir to prevent air from entering the
master cylinder.
10. Tighten bleeder screw securely and
remove bleeder hose.
11. Repeat procedure steps 5- 9 for the
remaining caliper (s).
12. Add brake fluid to MAX level on reservoir.
Master Cylinder Fluid Level:
MAX level or
Sight glass must look dark, if sight glass
is clear, fluid level is too low.
13. Install diaphragm, cover and screws.
Tighten screws to specification.
14. Field test machine at low speed before
putting into service. Check for proper
braking action and lever reserve. With
lever firmly applied, lever reserve should
be no less than 1/2 " (13mm ) from
handlebar.
15. Check brake system for fluid leaks and
inspect al hoses and lines for wear or
abrasion. Replace hose if w ear or
abrasion is found.

6.6 HAND BRAKE MASTER CYLINDER REMOVAL/ INSPECTION
/INSTALLATION
CAUTION: The master cylinder is a non-serviceable Component; it must be replaced as an
assembly.
NOTE: If any special service needed, contact the ATV manufacture via the agent for the parts
and special instruction.
REMOVAL
1. Clean master cylinder and reservoir
assembly. Make sure you have a clean work
area to disassemble brake components.
2. Place a shop towel under brake hose
connection at m aster cylinder. Loosen bolt,
remove bolt and sealing washers.
CAUTION
Brake fluid will damage finished surfaces.
Do not allow brake fluid to come in contact
with finished surfaces.
3. Remove master cylinder from handlebars.
INSPECTION
Inspect parking brake for wear. If teeth or
locking cam are worn, replace lever and test
the parking performance, if any locking
problem exists, Replace the master cylinder
as an assembly. NOTE: Mechanics parking
brake is equipped for new Europe model.
INSTALLATION
1. Install master cylinder on handlebars.
Torque mounting bolts to 55 in. lbs. (6 N m).
NOTE: To speed up the brake bleeding
procedure the m aster cylinder can be
purged of air before brake hose is attached.
Fill with DOT3 brake fluid and pump lever
slowly two to three times with finger over the
outlet end to purge master cylinder of air.
2. Place new sealing washers on each side
of hand brake hose and torque bolt to
specification.

Master Cylinder Mounting

Bolt Torque 55 in. lbs . (6 N m)
Brake Line Banjo Bolt Torque
15 ft. lbs. (21 Nm )
3. Fill reservoir with DOT 3 fluid.
4. Follow bleeding procedure, Check all
connections for leaks and repair if necessary.
6.7 FRONT PAD REMOVAL / INSPECTION / INSTALLATION

NOTE: The brake pads should be replaced as a set.
REMOVAL
1. Elevate and support front of ATV safely.
CAUT ION: Use care w hen supporting vehicle

so that it does not tip or fall. Severe injury m ay
occur if machine tips or falls.
2. Remove the front wheel.
3. Remove caliper from mounting bracket.
4. Push caliper piston into caliper bore slowly
using a C-clamp or locking pliers with pads
installed.
NOTE: Brake fluid will be forced through
compensating port into master cylinder fluid
reservoir when piston is pushed back into
caliper. Remove excess fluid from reservoir as
required.
5. Push mounting bracket inward and slip
outer brake pad past edge. Remove inner pad.
6. Measure the thickness of the pad material.
Replace pads if worn beyond the service limit.
INSPECTION
Measure the thickness of the pad friction
material. Replace pads if worn beyond the
service limit.
Service Limit 0.3/64"(1 mm)

INSTALLATION
1. Lubricate mounting bracket pins with a light
film of All Season Grease, and install rubber
dust boots.
2. Compress mounting bracket and make sure
dust boots are fully seated. Install pads with
friction material facing each other. Be sure
pads and disc are free of dirt or grease.
Front Caliper Mounting Bolts Torque 18 ft. lbs.
(25 Nm )
3. Install caliper on hub strut, and torque
mounting bolts.
4. Slowly pump the brake lever until pressure
has been built up. Maintain at least 1/2 ". (13
mm) of brake fluid in the reservoir to prevent
air from entering the brake system.
5. Install the adjuster screw and turn clockwise
until stationary pad contacts disc, then back off
1/2 turn (counter clockwise).
6. Install reservoir cap.
Hand and (or) Foot Brake Master
Cylinder(s) Fluid Level:
Between MIN and MAX lines
7. Install wheels and torque wheel nuts, test
and burnish.
See BURNISHING PROCEDURE
6.8 FRONT DISC INSPECTION / REMOVAL / REPLACEMENT

INSPECTION
1. Visually inspect the brake disc for nicks,
scratches, or damage.
2. Measure the disc thickness at 8 different
points around the pad contact surface using a
0-1" micrometer and a dial indicator. Replace
disc if worn beyond service limit.
New0.150-0.164"(3.810-4.166mm)
Service Lim it 0.140"/3 .556 mm
Service Limit 0.002 " (0.051mm)
difference between measurements
Brake Disc Runout
Service Limit 0.005" (0.127 mm)

REMOVAL/ REPLACEMENT
1. Removal caliper and hub. Apply heat to the
hub in the area of the brake disc mounting
bolts to soften the bolt locking agent.
2. Remove bolts and disc.
3. Clean mating surface of disc and hub.
4. Install new disc on hub.
5. and tighten to specified.
CAUTION: Always use new brake disc
mounting bolts.
Front Brake Disc Mounting Bolt Torque :
18 ft. lbs. (25 Nm )
6.9 FRONT CALIPER REMOVAL/ INSPECTION / INSTALLATION

CAUTION: The caliper is a non-serviceable Component; it must be replaced as an assembly.
REMOVAL
1. Remove wheel, remove caliper from the
strut.
2. Loosen and remove brake hose(s) to
caliper. Place a container under caliper to
catch fluid draining.
INSPECTION
Inspect caliper body for nicks, scratches or
worn. Replace caliper as an assembly if any
problem exists.
INSTALLATION
1. Install caliper on hub strut, Apply Loctite™
242 to screw threads and Install new bolts.
Front Caliper Mounting Bolt Torque
18 ft. lbs. (25 Nm )
2. Install brake hose and tighten securely.
hydraulic circulates (for foot brake and hand
brake) in one caliper. Make sure you install
the right hose.
3. Bleeding and Install wheels, If new brake
pads are installed, burnishing procedure
should be performed. See BURNISHING

PROCEDURE, And field test unit for proper

braking action before putting into service.
Inspect for fluid leaks and firm brakes. Make
sure the brake is not dragging when lever is
released. If the brake drags, recheck
assembly and installation.
6.10 REAR BRAKE PAD REMOVAL/ INSPECTION / INSTALLATION

NOTE: The brake pads should be replaced as a set.
REMOVAL and INSPECTION

1. Remove caliper mounting bolts and lift
caliper off of disc.
NOTE. When removing caliper, be careful not
to damage brake hose . Support caliper so as
not to kink or bend brake hose.
2. Push caliper pistons into caliper bore slowly
with pads installed.
NOTE: Brake fluid will be forced through
compensating port into m aster cylinder fluid
reservoir when piston is pushed back into
caliper. Remove excess fluid from reservoir as
required.
3. Remove brake pad retaining pin, and pad
spacer.
NOTE: Do not over spread this spring pin a-
part farther than necessary to remove it.
4. Clean.
5. Measure the thickness of the pad friction
material. Replace pads if worn beyond the
service limit.
Rear Brake Pad Service Limit 0.3/64"(1 mm)

INSTALLATION
1. Install new pads in caliper body. Be sure to
put spacer between pads.
2. Install caliper and torque mounting bolts.
Brake Caliper Torque: 18 ft. lbs. (25 Nm )
3. Slowly pump the brake lever until pressure
has been built up. Maintain at least 1/2 " (13
mm) of brake fluid in the reservoir to prevent
air from entering the master cylinder.
Hand and (or) Foot Brake Master
Cylinder(s) Fluid Level:
Between MIN and MAX lines
4. Install wheels, burnishing procedure should
be performed. See BURNISHING
PROCEDURE, And field test unit for proper
braking action before putting into service.
Inspect for fluid leaks and firm brakes. Make
sure the brake is not dragging when lever is
released. If the brake drags, recheck
assembly and installation.
6.11 REAR CALIPER REMOVAL/ INSPECTION/ INSTALLATION

CAUTION: The caliper is a non-serviceable Component; it must be replaced as an assembly.
1．Clean caliper area.
2．Using a flare nut wrench, remove hose(s).

Place a container to catch brake fluid draining
from brake hose.
3. Remove caliper.
4. Remove brake pad as described above.
5. Inspect surface of caliper for nicks,
scratches or damage and replace if necessary.
6. Install brake pads in caliper body with
friction material facing each other, with the
spacer between the pads. Install retaining pin
through outer pad, pad spacer and inner pad.
7. Install caliper and torque mounting bolts.
Caliper Mounting Bolt/ Caliper body Bolt
Torque:
18 ft. lbs. (25 Nm)

8. Install brake hose and tighten to specified

torque.
Banjo Bolt Torque: 15 ft. lbs. (21 Nm)
hydraulic circulates (for foot brake and hand
brake) in one caliper. Make sure you install the
right hose.
9. Bleed.
10. Field test unit for proper braking action
before putting into service. Inspect for fluid
leaks and firm brakes. Make sure the brake is
not dragging when lever is released. If the
brake drags, recheck assembly and
installation.
6.12 REAR BRAKE DISC INSPECTION / REMOVAL / REPLACEMENT

INSPECTION
1. Visually inspect the brake disc for nicks,
scratches, or damage.
2. Measure the disc thickness at 8 different
points around the pad contact surface using a
0-1" micrometer and a dial indicator. Replace
disc if worn beyond service limit.
New0.177-0.187"(4.496-4.750mm)
Service Lim it 0.167"(4.242 mm)
Service Limit 0.002 " (0.051mm)
difference between measurements
Brake Disc Runout
Service Lim it 0.005" (0.127 mm)
REMOVAL/ REPLACEMENT
1. Removal wheel/ hub and caliper.
2. Remove bolts and disc from the flange.
3. Clean mating surface of disc and hub.
4. Install new disc on flange.
5. Tighten to specified.
CAUTION: Always use new brake disc
mounting bolts.
Rear Brake Disc Mounting Bolt Torque :
18 ft. lbs. (25 Nm )

6.13 FOOT BRAKE PEDAL FOR B-TYPE

ADJUSTING
If the push rod joint is reinstalled, adjust the
push rod length so that the distance between
the centers of the master cylinder lower
mounting bolt hole and joint pin hole is
80±1mm.After adjustment, tighten the joint
nut.

NOTES

CHAPTER 7 ELECTRICAL LH500ATV-D SERVICE MANUAL 14.0
CHAPTER 7 ELECTRICAL
7.1 PARTS INSPECTION AND SERVICE
7.2 BATTERY
7.3 IGNITION SYSTEM
7.4 CHARGING SYSTEM
7.5 ELECTRICS STARTING SYSTEM
7.6 COOLING SYSTEM
7.7 LIGHTING SYSTEM
7.8 GEAR SHIFT SWITCH TEST
7.9 SPEEDOMETER SYSTEM
7.10 MAIN SWITCH AND HANDLE SWITCH
7.11 FUEL GAUGE/ FUEL LEVEL SENSOR
7.12 THE OPERATION PRINCIPLE OF THE ELECTRIC 4WD SHIFT
7.13 WIRING DIAGRAM
CHAPTER 7 ELECTRICAL PAGE.7- 1

7.1 PARTS INSPECTION AND SERVICE
HEADLIGHT LAMP REPLACEMENT

1. . ‘Use bulb 12V 35W/35W.
2. Pull the cable plug off the conducting
strip in the socket, remove the clip①
before
dismounting the bulb.
3. Fit a new bulb into the socket, sitting
properly in the three slots, install the
clip as shown in the fig. and connect
the cable plug to the conducting
strip.
4. Change the bulb.
HEADLIGHT ADJUSTMENT
1. The headlight beam can be adjusted vertically (all models) and horizontally (except the light on
handlebar).
2. Place the vehicle on a level surface with the headlight approximately 25’(7.6m) from a wall.
3. Measure the distance from the floor to the center of the headlight and make a mark on the wall at
the same height.
4. Start the engine and turn the headlight switch to high beam.
5. Observe headlight aim. The most intense part of the headlight beam should be aimed 2’ (51mm)
below the mark placed on the wall in step 2. NOTE : Riding weight must be included on the
seat.
6. Loosen but not remove pivot bolt/ screw and adjust beam to desired position.
7. Tighten nut and bolt / screw.
TAILLIGHT / BRAKELIGHT LAMP REPLACEMENT

1. From the rear of the taillight remove two screws holding lens cover in place and remove
lens cover. LENS COVER
2. Remove lamp and replace it with recommended
lamp.
3. Reinstall the lens cover removed in step 1.
4. Test the taillight / brake light. SCREWS

7.2 BATTERY
Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with
skin, eyes or clothing Antidote:
External: Flush with water.
lnternal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg, or
vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
Batteries produce explosive gases. Keep sparks, flame, cigarettes, etc. away. Ventilate when
charging or using in an enclosed space. Always shield eyes when working near batteries.
KEER OUT OF REACH OF CHILDREN
WARNING: The gases given off by a battery are explosive. Any spark or open flame near a battery
can cause an explosion which will spray battery acid on anyone close to it. If battery acid gets on
anyone, wash the affected area with large quantities of cool water and seek immediate medical
attention.
To ensure maximum service life and performance from a new battery, perform the following steps.
NOTE: Do not service the battery unless it will be put into regular service within 30 days. After initial
service, add only distilled water to the battery. Never add electrolyte after a battery has been in
service.
NOTE: New Battery must be fully charged before use.
1. Remove vent plug from vent fitting.
2. Fill battery with electrolyte to upper level marks on case.
3. Set battery aside and allow it to cool and stabilize for 30 minutes.
4. Add electrolyte to bring level back to upper level mark on case.
NOTE: This is the last time that electrolyte should be added. If the level becomes low after this point,
add only distilled water.
5. Charge battery at 1 /10 of its amp /hour rating. Examples: 1 /10 of 14 amp battery = 1.4 amp;
1/10 of 7 amp battery = 0.7 amp (recommended charging rates).
6. Check specific gravity of each cell with a hydrometer to assure each has a reading of 1.270 or
higher.
BATTERY INSPECTION / REMOVAL

The battery is located under the left rear fender. Inspect the battery fluid level. When the battery fluid
nears the lower level, the battery should be removed and distilled water should be added to the
upper level line. To remove the battery:
1. Disconnect holder strap and remove cover.
2. Disconnect battery negative (-) (black) cable
first,
followed by the positive (+) (red) cable.
CAUTION
Whenever removing or reinstalling the battery, disconnect the negative (black) cable first and
reinstall the negative cable last!
3. Disconnect the vent hose.
4. Remove the battery.

5. Remove the filler caps and add distilled water only as needed to bring each cell to the proper
level.
Do not overfill the battery.
To refill use only distilled water. Tap water contains minerals which are harmful to a battery.
Do not allow cleaning solution or tap water to enter the battery. It will shorten the life of the
battery.
6. Reinstall the battery caps.
BATTERY INSTALLATION
1. Clean battery cables and terminals with a stiff wire brush. Corrosion can be removed using a
solution of one cup water and one tablespoon baking soda. Rinse with clean water and dry
thoroughly.
2. Reinstall battery, attaching positive (+) (red) cable first and then the negative (- ) (black) cable.
3. Install clear battery vent tube from vehicle to battery vent.
WARNING:Vent tube must be free from obstructions and kinks and securely installed. If not, battery
gases could accumulate and cause an explosion. Vent should be routed away from frame and body
to prevent contact with electrolyte. Avoid frame, corrosion will occur.
4. Route cables so they are tucked away in front and behind battery.
5. Reinstall battery cover and holder strap.
Do not start the engine with the battery disconnected. Vehicle lamps will burn out if battery is
disconnected during vehicle operation. Also, the reverse speed limiter can be damaged.
BATTERY TESTING
Whenever a service complaint is related to either the starting or charging systems, the battery
should be checked first.
Following are three tests which can easily be made on a battery to determine its condition: OCV
Test, Specific Gravity Test and Load Test.
MF (Maintenance Free) battery does not require the Specific Gravity Test and Refill
Open Circuit Voltage Test

Battery voltage should be checked with a digital multitester. Readings of 12.6 or less require
further battery testing and charging.
NOTE: Lead acid batteries should be kept at or near a full charge as possible.
Load test
CAUTION: Remove spark plug high tension leads and connect securely to engine ground before
proceeding.
NOTE: This test can only be performed on machines with electric starters. This test cannot be
performed with an engine or starting system that is not working properly.
A battery may indicate a full charge condition in the OCV test and the specific gravity test, but still
may not have the storage capacity necessary to properly function in the electrical system. For this
reason, a battery capacity or load test should be conducted whenever poor battery performance is
encountered. To perform this test, hook a multitester to the battery in the same manner as was
done in the OCV test. The reading should be 12.6 volts or greater. Engage the electric starter and
view the registered battery voltage while cranking the engine. Continue the test for 15 seconds.
During this cranking period, the observed voltage should not drop below 9.5 volts. If the beginning
voltage is 12.6 or higher and the cranking voltage drops below 9.5 volts during the test, replace the
battery.

7.3 IGNITION SYSTEM
IGNITION SYSTEM TROUBLESHOOTING

No Spark, Weak or Intermittent Spark
z Spark plug gap incorrect
z Fouled spark plug
z Faulty spark plug cap or poor connection to high tension lead
z Related wiring loose, disconnected, shorted, or corroded
zEngine stop switch or ignition switch faulty
z Terminal board or connections wet, corroded
z Poor ignition coil ground (e.g. coil mount loose or corroded)
z Faulty stator (measure resistance of all ignition related windings)
zIncorrect wiring (inspect color coding in connectors etc. )
z Faulty ignition coil winding (measure resistance of primary and secondary)
z Worn magneto (RH) end crankshaft bearings
z Sheared flywheel key
z Flywheel loose or damaged
z Trigger coil air gap too wide (where applicable) should be 0.030-0 .050" (0. 75-1.25 mm)
z Excessive crankshaft run out on magneto (RH) end should not exceed 0.005"
(0.13mm)
z Faulty CDI module
CIRCUIT DIAGRAM

IF THE IGNITION SYSTEM FAILS TO OPERATE
Procedure
Check:
1. Fuse (Main) 7.Pickup coil resistance
2. Battery 8.Main switch
3. Spark plug 9.Engine stop switch
4. lgnition spark gap 10.Wiring connection
5. Spark plug cap resistance (entire ignition system)
6. Ignition coil
1.Fuse NO CONTINUITY
Check switches
Replace the fuse.
CONTINUITY
2. Battery INCORRECT
z Check the battery condition. z Clean battery terminals.
Refer to "BATTERY z Recharge or replace the battery.
INSPECTION"
CORRECT Standard spark plug: DPR7EA 9 /
NGK
3.Spark plug
OUT OF SPECIFICATION
z Check the spark plug
condition.
z Check the spark plug
type. Repair or replace the spark plug
z Check the spark plug gap.
Spark plug gap: 0.6 ～

0.7mm

4.lgnition spark gap

z Disconnect the spark plug cap from the
spark plug
zConnect the ignition tester 1 as shown.
2 Spark plug
zTurn the main switch to "ON".
zCheck the ignition spark gap .
zCheck the spark by pushing the
MEETS SPECIFICATION
starter switch, and increase the spark
gap until a misfire occurs.
The ignition system is not faulty.
Minimum spark gap:
6mm (0.24 in)
OUT OF
SPECIFICATION Tester (+) lead →
OR Spark plug sidec
NO SPARK Tester (—) lead→
5.Spark plug cap resistance High tension cord side d
zRemover the spark plug cap.
zConnect the pocket tester (ΩX1 k) to
the spark plug cap.
NOTE:
z When removing the spark plug cap.
do not pull the spark plug cap from
high tension cord.
zRemove→Turning
counterclockwise
zConnect→Turning clockwise.
zCheck the high tension cord
when connecting the spark
plug cap.
z When connecting the spark plug cap,
cut the high tension cord about 5mm.
Spark plug cap
resistance:
Replace the spark plug cap
10KΩ(20 ℃)
CORRECT

* Tester (+) lead

B/Y Terminal
Tester ( -) lead Green
6. Ignition coil resistance Terminal
Disconnect the ignition coil
connector from the wire
harness.
zConnect the pocket tester
(1) to the ignition coil.
z Check if the primary coil
has the specified resistance.
Primary coil resistance:

3.6-4.8Ω (20 ℃)
Tester (+) lead
Spark plug lead
Tester (— ) lead
Green Terminal

(Ω×1k ) to the ignition coil.
zCheck the secondary has the
specified resistance
Secondary coil resistance: OUT OF SPECIFICATION
3.5kΩ±10％ (20℃)
BOTH MEET
SPECIFICATION
Replace the ignition coil.
*

7. Pickup coil resistance

z Disconnect the pickup coil coupler
from the wire harness.
zConnect the pocket tester (Ω 100) to
the pickup coil coupler.
Tester (+) lead →

BI/Y Terminal c
Tester (- ) lead→
B/R Terminal d
z Check the pickup coil has the
specified resistance.
Replace the pickup coil.
Primary coil resistance:

115 -145Ω (20℃)
MEETS
SPECIFICATION
NO CONTINUITY
8.Main switch
CHECK SWITCHES
Replace the main switch
CONTINIUTY
NO CONTINUITY
9.Engine stop switch ( for USA

model)
Replace the handlebar switch.
CONTINIUTY
10.Wiring connection
zCheck the connection of the POOR CONNECTIONS
entire ignition system
Refer to “CIRCUIT DIAGRAM”.
Correct
CORRECT
Replace the igniter unit.

7.4 CHARGING SYSTEM
CHARGING SYSTEM CIRCUIT DIAGRAM
CURRENT DRAW - KEY OFF
CAUTION: Do not connect or disconnect the battery cable or ammeter with the engine running.
Damage will occur to light bulbs and speed limiter.
Connect an ammeter in series with the negative battery cable. Check for current draw with the key off,
if the draw is excessive, loads should be disconnected from the system one by one until the draw is
eliminated. Check component wiring as well as the component for partial shorts to ground to eliminate
the draw.
Current draw key off:

Maximum of 0.01DCA(10mA)

CHARGING SYSTEM
Procedure
Check:
1. Fuse (Main) 4.Stator coil resistance
2. Battery 5.Wiring system (entire charging system)
3.Charging voltage
1. fuse NO CONTINUITY
Replace the fuse

2. Battery
Check the battery condition. INCORRECT

Refer to "BATTERY INSPECTION"
Clean battery terminals

Recharge or replace the battery
3.Charging voltage
Connect the engine tachometer
to the spark plug lead.
(DC20V) to the battery
Test (+) lead→
Battery (+) terminal c
Tester (-) lead→
Battery (-) terminal d
Measure the battery terminal
voltage.
start the engine and accelerate to
about 5,000rpm
zcheck the terminal voltage
Measured voltage-terminal MEETS SPECITICATION
Voltage:
0.2-2.5V up
NOTE: Use a fully changed battery.
The charging circuit is not faulty

Replace the battery
OUT OF SPECICATION

4. Starter coil resistance
Remove the A.C. magneto coupler from
wire harness
Connect the pocket tester (ΩX1) to
the stator coil
Tester (+) lead –yellow terminal
Tester (-) lead –yellow terminal OUT OF SPECITICATION
Measure the stator coil resistance
Stator coil resistance 0.5-0.8Ω（20 ）
Replace the stator coil
MEETS SPECIFICATION
5.Wiring connection
check the entire charging system for
connections
Refer to “CIRCUIT DIAGRAM” POOR CONNECTION
correct
CORRECT
Replace the rectifier/regulator

7.5 ELECTRICS STARTING SYSTEM

DIAGRAM

TROUBLESHOOTING
THE STARTER MOTOR OPERATES WHEN GEAR SHIFT SWITCH IS IN NEUTRAL OR THE
FRONT/REAR SWITCH IS ON
IF THE STARTER MOTOR FAILS TO OPERATE
Procedure
Check:
1. Fuse (Main) 7. gear shift switch
2. Battery 8. front/rear brake switch
3. starter motor 9. starter switch
4. starter relay 10. wiring connection (entire starting system)
5. aux relay
6. main switch
1. fuse
refer to “CHECKING SWITCHES” NO CONTINUITY
section
Replace the fuse
2. Battery
Refer to "BATTERY INSPECTION" section
in CHAPTER 3

3. Starter motor DOES NOT MOVE

Connect the battery positive terminal
and starter motor cable using a jumper
lead.
Check the starter motor operation
Repair or replace the starter

motor

4.Starter relay WARNING

A wire used as a jumper lead
zDisconnect the relay unit coupler from must have the equivalent
the wire harness. capacity as that of the battery
zConnect the pocket tester (Ωx1) and lead or more, otherwise it
battery (12V) to the relay unit coupler may burn.
terminals. This check is likely to
Battery (+) lead→ produce sparks, so be sure
Green/Yellow terminal c that no flammable gas or fluid
Battery (-) lead→ is in the vicinity
Yellow/Red terminal d
zCheck the starter relay for continuity.
Test (+) lead → e terminal
Test (-) lead → f terminal
CONTINUITY
Replace the starter replay
5. .Aux relay
zDisconnect the aux relay coupler from
the wire harness.
zConnect the pocket tester (Ωx1) and
battery (12V) to the aux relay coupler
terminals.
Battery (+) lead→ terminal d
Battery (-) lead→ terminal f
zCheck the aux relay for continuity.
Test (+) lead → c terminal
Test (-) lead → e terminal
Replace the aux relay

6. Main switch
CHECK SWITCHES NO CONTINUITY

7.Gear shift switch
CHECK SWITCHES
NO CONTINUITY
Replace the handlebar switch
8 Front /rear brake switch

NO CONTINUITY
CHECKING SWITCHES
Replace the brake switch
9. Starter switch
NO CONTINUITY
CHECKING SWITCHES
Replace the handlebar switch
10. Wiring connection

POOR CONNECTION
Check the connections of the entire
starting system.
Refer to “CIRCUIT DIAGRAM
Correct

7.6 COOLING SYSTEM
IF THE FAN MOTOR FAILS TO TURN

Procedure
Check:
1. Fuse (Main, Fan)
2. Battery 4. Fan motor (inspection)
3. Main switch 5. Thermo switch
6. relay
7. Wiring connection (entire cooling system)

1. fuse
Replace the fuse

2. Battery
Refer to "BATTERY INSPECTION" section

3 Main switch
4.1 Fan motor(inspection 1)

Connect the battery to the fan motor.
Battery (+) lead→Green/Blue terminal DOES NOT MOVE
c
Battery (-) lead→Green ground d
Check the fan motor operation
Replace fan motor
4.2 Fan motor (inspection 2)

Turn the main switch to off.
zRemove the thermo switch lead from DOES NOT MOVE
thermo switch.
zConnect jumper lead to thermo switch
leads.
zTurn the main switch to on
The wiring circuit from battery to

fan motor is faulty. Repair

5. Thermo switch
Remove the thermo switch from the
radiator.
zConnect the pocket tester (ΩX1) to the
thermo switchc.
zImmerse the thermo switch in the
water d
zCheck the thermo switch for continuity.
NOTE:
Measure temperatures while heating the
coolant with the temperature gauge
WARNING
zHandle the thermo switch with special
care.
Never subject it to strong shocks or
allow it to be dropped. Should it be
dropped, it must be replaced.
zDo not touch the thermo switch to the
bottom of the heated vessel.
88±3 Thermo switch “ON” OUT OF SPECIFICATION

80 Thermo switch “OFF”
Replace the thermo switch
6.Relay
zDisconnect the starting circuit cut-off
relay coupler from the wireharness.
zConnect the pocket tester (Ωx1) and
battery (12V) to the starting circuit cut-off
relay coupler terminals.
Battery (+) lead→ terminal d
Battery (-) lead→ terminal f
zCheck the starting circuit cut-off relay
for continuity.
Test (+) lead → c terminal
Test (-) lead → e terminal

7. Wring connection
UPPER CONNECTION
zCheck the connection of the entire
cooling system.
Refer to “CIRCUIT DIAGRAM”
Correct
IF THE HEAT ALARM UNIT WORKING

When the main switch is turned on, the temperature of the engine begins to go up. As it
comes to 88±3 the thermostat is connected and the fan starts to work, cooling the coolant, if
the thermostat or the fan, fails to work; the coolant temperature will keep rising. The heat alarm
unit operates the moment the temperature reaches 115±5 and the signal flashing. Stop the
engine now to have the circuit fixed.
Procedure
Check:
1 .Fuse(Main, Fan) 4. Thermo unit
2. Battery 5. Voltage
3.Main switch 6. Wiring connection (entire cooling system)
1. fuse
CHECKING SWITCHES NO CONTINUITY
Replace the fuse

2. Battery
Refer to "BATTERY INSPECTION"

3.Main switch
CHECKING SWITCHES NO CONTINUITY

Handle the thermo unit with

4.Thermo unit
special care.
zDrain the coolant and remove the
Never subject it to strong
thermo unit from the cylinder head.
shocks or allow it to be
zImmerse the thermo unit din the
dropped.
coolante .
Should it be dropped, it must be
cThermometer.
replaced.
Do not touch the thermo unit to
the bottom of the heated vessel.
Coolant Resistance
temperature
47.5~56.8Ω
80
100 26.2~29.3Ω
Replace the thermo unit
MEETS SPECIFICATION
8. Voltage
zConnect the pocket tester (DC20V) to
the
Temperature gauge couple.
Tester (+) lead→Green/Blue terminal
Tester (-) lead→Green ground
zTurn the main switch to on. OUT OF SPECIFICATION
zCheck for voltage (12V) on the
temperature gauge lead.
The wiring circuit from main

switch to temperature gauge
is faulty. Repair.
8. Wiring connection check the POOR CONNECTION

connections of the entire cooling
system.
Refer to “CIRCUIT DIAGRAM”
CORRECT
Replace the temperature gauge

7.7 LIGHTING SYSTEM

TROUBLESHOOTING
Procedure
Check:
1. Fuse (Main) 4.Lights switch
2. Battery 5.Dimmer switch
3. Main switch 6. Wiring connection (entire lighting system)
1.fuse
refer to “CHECKING SWITCHES” NO CONTINUITY
section
Replace the fuse

2. Battery
Refer to “BATTERY INSPECTION” section
in CHAPTER 3

3. Main switch
NO CONTINUITY
CHECK SWITCHES
4. Light switch
NO CONTINUITY
CHECK SWITCHES
Replace the right handlebar

switch
5. Dimmer sw
NO CONTINUITY
CHECK SWITCHES
Replace the left handlebar

switch

POOR CONNECTIONS
7. Wiring connection
Check the connection of the entire
lighting system
correct
8. check the condition of each of the

lighting system’s circuits
Refer to “LIGHTING SYSTEM CHECK”
LIGHT SYSTEM CHECK

1. If the headlight and the high beam indicator light fail to come on
NO CONTINUITY
1.Blub and bulb socket
CHECK SWITCHES
Replace the bulb and/ or bulb

socket
2. Voltage
Connect the pocket tester (DC20V) to
the headlight and high beam indicator
light couplers.
A When the dimmer switch is on low

beam.
B When dimmer switch is on high
beam
Headlight::
Tester (+) lead →White cor Blue dlead
Tester negative (-) lead →Green elead
Turn the main switch to on.

Turn the light switch to on position.
Turn the dimmer switch to low beam or
high beam.
Check for voltage (12V) on the lead at
bulb socket connectors OUT OF SPECIFICATION
The wiring circuit from the main

switch to
This circuit is not faulty bulb socket connector is faulty.
Repair

2. the taillight fails to come on
1. Bulb and bulb socket NO CONTINUITY
CHECK SWITCHES
Replace the bulb and /or bulb

socket
CONTINUITY
2. Voltage
Connect the pocket tester (DC20V) to
the bulb
socket connector.
Tester (+) lead→
Black terminal c
Tester (-) lead→
Green terminal d
Turn the main switch to on. OUT OF SPECIFICATION
Turn the lights switch to on pilot position.
Check the voltage (12V) on the bulb
socket connector
The wiring circuit from main

switch to
bulb connector of faulty.
Repair
This circuit is not faulty

7.8 GEAR SHIFT SWITCH TEST
DIAGRAM

Switch table

7.9 SPEEDMETER SYSTEM
OPERATION OF SPPED SENSOR

Speed Sensor is on the engine
Operation Instructions of Electric Dial Meter and Speed Sensor/ Operation Instructions of LCD Meter
and Speed Sensor
A. Hall Sensor is a new type sensor used to measure speed, angle, revolution and length, etc by
means of voltage pulse signals converted from sensing gear ratio of black metal gear or gear
rack.
B. Main Technical Parameter for sensor：
Item Code Vol value Unit
Operating voltage Vcc 5-20 V
Operating current Icc ≤15 mA
Operating distance D 1mm ≤ D ≤ 2.5mm mm
C. The following is the graphic illustration for sensor installation, Wire 1 (red) is positive and wire 2
(black) negative, Wire 3 (yellow) works as the one to output signals.
The following is the graphic illustration for sensor installation。

METER
Dial Meter
Item Vol value Unit

Operating voltage 10V~18V V
Operating current ≤ 500mA A
Operating Environmental temperature -10 ~65
Battery warning voltage ≤11.5V V
LCD Meter
1. Neutral indicator light 8、9. The odometer

2. High beam indicator light 10.Engine working hour counter
3. Turn indicator light 11. 2WD/4WD indicator
4. Reverse indicator light A: km/ mile selector
5. Speedometer B: hour / distance selector
6. Coolant temperature meter 12. Fuel gauge Indicator
7. Engine rpm meter 13. Power Indicator
14.Gear position indicator

7.10 MAIN SWITCH AND HANDLE SWITCH
HANDLE SWITCH SCHEMATIC FOR EUROPE MODEL

7.11 FUEL GAUGE/ FUEL LEVEL SENSOR
Removal
Turn the ignition switch to“OFF”.
Remove the fuel tank cover.
Remove the four bolts, retaining plate
and fuel level sensor from the fuel
tank.
Installation
Install a new seal rubber onto the fuel
level sensor.
Install the retaining plate onto the
sensor
Install and tighten the bolts securely.

Install the removed parts in the
reverse order of removal.
Fuel Gauge / Fuel level Sensor

Inspection
Move the float to the bottom
(RESERVE) position, turn the ignition
switch to “ ON ” and check the fuel
gauge.
Segment“RES”should blink.
SEGMENT “RES”

With the fuel level sensor float at the

top (FULL) position, turn the ignition
switch to “ON” and check the fuel
gauge. All segments up to segment
“F”should come on.
If the fuel gauge does not function FULL

properly, check the fuel level sensor
If the fuel level sensor is OK, replace
the LCD Meter.
Fuel level Sensor Inspection

Disconnect the fuel level sensor 2p RESISTANCE(20℃/
FLOAT POSITION
Green connector and connect the 68°)
ohmmeter to the sensor side
connector terminals. TOP(FULL) 4-10Ω
Measure the fuel level sensor BOTTOM(RESERVE) 100-110Ω
resistance with the float at the top
(FULL)
And bottom (RESERVE) positions.

7.12 THE OPERATION PRINCIPLE OF THE ELECTRIC 4WD SHIFT
(Fig 1)
1, The rider shifts 2WD to 4WD by the Switch on handlebar.

2. When shift 2WD/ 4WD or Diff Lock, the mechanics in the front gear box maybe still engaged/
disengaged, the mechanics would finally disengaged/ engaged when rides on a hard surface or
rides in reverse.
3. Always shift as the vehicle stop.

7.13 WIRING DIAGRAM

CHAPTER 8 ELECTRICAL ATV SERVICE MANUAL 09.0
CHAPTER 8 ELECTRICAL CTRICAL PAGE 8- 35

Service Manual: ATV 500-D

Uploaded by

Copyright:

Available Formats

Service Manual: ATV 500-D

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: ATV 500-D

Uploaded by

Copyright:

Available Formats

2014 ATV

SERVICE MANUAL EUROPE 14.0

Cette revue concerne les modèles suivants :

LH500ATV-D 维修手册欧标英文 版本 14.0 零件代号 F010102A14

CHAPTER1 ………………………………………………General Information↖

CHAPTER3……………………………………. …. ………………500 Engine↖

CHAPTER 1 GENERAL INFORMATION

1.1 IMPORTANT INFORMATION

1.2 V.I.N AND ENGINE SERIAL NUMBER

1.3 VEHICLE DIMENSIONS

CHAPTER 1 GENERAL PAGE. 1- 1

1.1 IMPORTANT INFORMATION

PREPARATION FOR REMOVAL PROCEDURES

GASKETS,OIL SEALS AND O-RINGS

LOCK WASHERS/PLATES AND COTTER PINS

Replace all lock washers/plates and cotter pins

BEARINGS AND OIL SEALS

CHAPTER 1 GENERAL PAGE. 1- 2

7. Check for continuity with a tester.

CHAPTER 1 GENERAL PAGE. 1- 3

How to use the CONVERSION TABLE

CHAPTER 1 GENERAL PAGE. 1- 4

1.2 V.I.N AND ENGINE SERIAL NUMBER

CHAPTER 1 GENERAL PAGE. 1- 5

CHAPTER 1 GENERAL PAGE. 1- 6

1.3 VEHICLE DIMENSIONS

CHAPTER 1 GENERAL PAGE. 1- 7

CHAPTER 1 GENERAL PAGE. 1- 8

2.1 PERIODIC MAINTENANCE

2.2 FUEL SYSTEM

2.3 TOE ALIGNMENT

2.4 BRAKING SYSTEM INSPECTION

2.5 SUSPENSION SPRING RPELOAD ADJUSTMENT

2.7 TIRE PRESSURE

2.8 FRAME, NUTS, BOLTS, FASTENERS

CHAPTER 2 MAINTENANCE PAGE. 2- 1

2.1 PERIODIC MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE

Item Hours When Remarks

CHAPTER 2 MAINTENANCE PAGE. 2- 2

Coolant strength 25 hrs 3 months I Inspect strength seasonally

▲ Air Box Sediment Tube / Daily D

Headlamp Inspection / Daily C

Battery fluid level 10 Monthly I

DL Brake pad wear 2 Weekly I

▲ Gear case Oil 10 Monthly C

▲ Engine breather hose 100 hrs 6 months I

Throttle Cable / Pre-ride I

DL Throttle Cable 50 hrs 6 months A L (Grease M) R if necessary

Shift linkage 50 hrs 6 months I A R if necessary

DL Transmission belt 50 hrs 6 months I

▲ Rear Axle ( and Bearings) 50 hrs 6 months I L

CHAPTER 2 MAINTENANCE PAGE. 2- 3

▲ Front Suspension 50 hrs 6 months I L

Radiator 100 hrs 12 months I R

Cooling System hoses 50 hrs 6 months I

DL Valve clearance 100 hrs 12 months I A

Brake fluid 200 hrs 24 months Change every two years

DL sprockets) in transmission 4X4), or 1000 hrs ( in

LH500ATV-D 维修手册欧标英文版本 14.0 零件代号 F010102A14