Industrial Motors Overview

Introduction to TMEIC Motors

WWW.TMEIC.COM
JAPAN | NORTH AMERICA | SOUTH AMERICA | EUROPE | SOUTHEAST ASIA | INDIA | CHINA | MIDDLE EAST | AUSTRALIA
Introduction to TMEIC Motors
TMEIC combines the best of Toshiba and Mitsubishi-
Electric’s experience in building motors that goes back
over 100 years. TMEIC’s motor offering includes induction
motors from a few hundred horsepower, up to
synchronous motors over 100,000 hp, driving a wide
range of industrial applications such as pumps, fans,
grinding, conveyors, and compressors.

In addition to applications directly connected to utility

power, TMEIC motors can be matched with Variable
Frequency Drives for ease of starting and for speed
control. The VFD allows motor speeds as high as 12,000
rpm. This chart below and pages 4 & 5 illustrate the range
of motors available.

100
Synchronous motors are best suited for
very high power at lower speeds. Expansion of the oil and gas industry has created demand
80
Induction motors are best suited for for large motors to drive gas compressors and oil pumps.
high speed.
These motors are located in the production areas and on
70 Considerable over lap exists to allow
a choice, but the induction motor interstate pipelines, and are usually designed with explosion
usually has the price advantage in the protection. For special applications such as driving large
60 overlap area.
Power (MW)

compressors and blowers, motor ratings can reach or

50 Synchronous Motors exceed 100,000 hp.

Meeting the demand for large motors for the metals

40
industry, TMEIC has produced large synchronous and
Induction Motors
30
induction motors for the operation of steel rolling mills.
The power levels for these motors go up to about 10 MW.
20 They are covered in a separate brochure.

10

0
0 3000 6000 9000 12000 15000
Rotating Speed (RPM)

Features Benefits

High Reliability resulting from use of proven design Many years of excellent trouble-free service under
technology, manufacturing expertise, wide use of difficult working conditions
robotics, tight quality control, and testing

High Efficiency resulting from detailed analysis of Low electrical losses for high power conversion
the electromagnetic field patterns and ventilating air efficiency
flows

High Strength Insulation applied by robotic Withstand surge and minimizes electrical shorts
insulation winding and oversized epoxy resin vacuum and winding fatigue failure
impregnation tanks creates strong support and
insulation

High Mechanical Strength through use of static and Minimizes mechanical deflection and vibration for
dynamic strength analysis of stator frame, rotor, shaft longer equipment life
and bearings. Motor shafts are made of forged steel
with high tensile strength

2
High-Quality Design, Manufacturing, and Testing
TMEIC produces high-quality motors by employing the Continuous Improvement
best design, manufacturing, and test procedures. The manufacturing system
Advanced computer aided design and analysis allows has specified standards, and
motor performance to be predicted in advance. The world the actual performance is
class manufacturing automation system produces high- measured against these.
quality parts, on time, with no exceptions. These Continuous quality
automated systems produce components and assemblies improvement is built in, with
meeting the highest quality requirements, delivery product quality steadily
schedule, and long life. improving as a natural
outcome. Large Stator Assembly

Excellent Motor Design Tools – Extensive CAD and Computerized Finite Element Analysis

CAD Computer
Aided Design

TMEIC motor engineers make extensive FEM Electromagnetic Analysis FEM Natural Frequency Analysis
use of computer aided design to
produce their detail and assembly Enhanced computerized Finite Element Analysis is used to analyze and optimize
drawings, both two-dimensional and electromagnetic field strength, rotor stress and dynamics, frame natural
three-dimensional. frequencies, cooling air flow patterns, and internal temperatures.

High-Quality Manufacturing –
World-Class Motor Test
Computer Control and Robotics

Manufacturing procedures TMEIC’s fully instrumented

make use of computer computer automated
control and robotics to test (CAT) facilities allow
increase the speed of the motors to be load and
work, maintain accuracy, speed tested. The example
and ensure repeatability of facility shown here was
the operations. Examples built to test large motors
include: Robotic Stator Core and drives at high speed.
Lamination Stacking This back-to-back test
• Air duct plate arrangement used:
robotic assembly
• Segmented core lamination robotic assembly • Variable frequency drive to provide power and desired
• Round core lamination robotic assembly speed to the test motor
• Rotor field core robotic assembly • Generator to load the test motor
• Computer controlled core stamping • Variable frequency drive to recycle power back to the
supply

3
TMEIC Motor Product Overview

Induction Motors
Product
LV and MV Mill Motors MV Motors MV Motors MV Motors
TM21™-FII TM-AC TM21-G TM21-H TM21-MII

Typical
View

37-1,400 kW 44-370 kW Up to 23,000 kW Up to 8,000 kW Up to 3,550 kW

Power
(50-1,870 hp) (59-490 hp) (30,800 hp) (10,270 hp) (4,750 hp)

Speed Up to 3,600 rpm Up to 1,300 rpm Up to 3,600 rpm Up to 3,600 rpm Up to 3,600 rpm

Voltage Up to 6.9 kV 420 Vac max. 2 – 11 kV 13.8 kV 2 –11 kV

Open Drip Proof –

ODP/IP22
Weather Protected Weather Protected II-
Totally Enclosed Weather Protected
II-WPII/IP24W WPII/IP24W
Forced Ventilated – II-WPII/IP24W
TEFV Totally Enclosed Totally Encl. Air to Air
Totally Enclosed Totally Encl. Air to Air
Air-to-Air-Cooled – Cooled – TEAAC/IP55
Enclosure Fan Cooled –TEFC/ Drip Proof Forced Cooled – TEAAC/IP55
TEAAC/IP54/IP55/IP56
IP55 Ventilated – DPFV Totally Encl. Water to
Totally Enclosed
Totally Encl. Water to
Air Cooled – TEWAC/
Totally Enclosed Non Water-to-Air-Cooled– Air Cooled – TEWAC/
IP55/56
Ventilated – TENV TEWAC/IP54/IP55/IP56 IP55/56
Totally Encl. Separately
(Pipe) Ventilated –
TESV/IP55/56

Classified
Exn, Extc, Exd N/A Exn, Exe, Exp Exn, Exe, Exp Exn, Exe, Exp, ExtD
Area

Aluminum die Aluminum die cast

Alum. die cast rotor
Rotor cast rotor, or rotor or Copper Copper rotor bars Copper rotor bars
Opt. copper rotor bars
Copper rotor bars rotor bars

Ball & roller Ball & roller Ball & roller bearings, Ball & roller bearings, Ball & roller bearings,
Bearing grease lubrication grease lubrication grease lubrication
bearings, grease bearings, grease
Options
lubrication lubrication Sleeve bearings Sleeve bearings Sleeve bearings

Available IEC, NEMA, BS, Based on JEC-2137 IEC, NEMA, BS, AS, IEC, NEMA, BS, CSA, IEC, NEMA, BS, AS,
Standards AS, CSA, API and IEC 60034-1 CSA, IS, JEC JIS, JEC, JEM, API CSA, API

Fans, Blowers, Fans, Blowers, Fans, Blowers, Fans, Blowers,

Major Steel Mills,
Compressors, Compressors, Mills, Compressors, Mills, Compressors, Mills,
App. Aluminum Mills
Conveyors Conveyors Conveyors Conveyors

4
 Synchronous Motors

Medium-High
MV Motors Vertical Motors High Speed Main Drive Motor High-Speed
Power
TM21-L TM21-VL & VLL (Custom design) (Custom design) (Custom design)
(Custom design)

Up to 18,500 kW Up to 6,500 kW Up tp 8,000 kW Up to 80,000 kW Up to 80,000 kW

12,000 kW
(25,000 hp) (8,700 hp) (10,720 hp) (107,240 hp) (107,240 hp)
Up to 1,800 rpm,
Up to 11,900 rpm Very low speed up
Up to 3,600 rpm option > than 30 Up to 1,540 rpm Up to 6,500 rpm
on VFD power to 3,600 rpm
poles

2 –13.8 kV 2 –13.8 kV 2.3 -11 kV Up to 6.6 kV 3.3 –13.8 kV Up to 13.8 kV

Open Drip Proof –

ODP/IP22
Weather Protected Open Drip Proof –
II-WPII/IP24W ODP/IP22 Totally Enclosed
Totally Enclosed
Totally Encl. Air to Weather Protected Air to Air Cooled–
Air-Air Cooled–
Air Cooled – TEAAC/ II-WPII/IP24W TEAAC/IP55 Totally Enclosed
Totally Enclosed TEAAC/IP55
IP55 Totally Enclosed Totally Enclosed Water to Air
Water to Air Totally Enclosed
Totally Encl. Water to Air to Air Cooled – Water to Air Cooled – TEWAC/
Cooled – TEWAC Water to Air
Air Cooled – TEWAC/ TEAAC/IP55 Cooled – TEWAC/ IP55
Cooled – TEWAC/
IP55 Totally Enclosed IP55 (Blower
IP55
Water to Air Cooled ventilated)
Totally Encl.
Separately – TEWAC/IP55
(Pipe) Ventilated –
TESV/IP55

Exn, Exe, Exp, ExtD Exn, Exe, Exp Exn, Exe, Exp N/A Exp Exp

Cylindrical solid
Aluminum alloy rotor for two- Cylindrical solid
Copper rotor bars Copper rotor bars Salient Poles
rotor bars pole, salient pole rotor, two-pole
all others
Ball & roller Sleeve bearings
Antifriction
bearings, grease Magnetic bearings Tilting pad
bearings Sleeve Bearings Sleeve bearings
lubrication Tilting pad bearings bearings
Tilting pad bearings
Sleeve bearings Magnetic bearings
IEC, NEMA, BS, AS, IEC, NEMA, BS,
IEC, NEMA, BS, AS IEC, JEC IEC IEC
CSA, API AS
Metal Rolling
Fans, Blowers, Mills, Blowers,
Gearless Mills Turbo Blowers, Gearless
Compressors, Mills, Pumps Pumps,
Compressors Compressors (Ind. Compressors
Conveyors Compressors
Motors Also)

5
TM21-M and TM21-L Series Induction Motors
TMEIC offers a range of medium voltage induction motors fabricated steel frames. Aluminum rotor bars are standard
for larger Industrial applications such as fans, blowers, on the TM21-M, and copper rotor bars are standard on the
pumps, mills, compressors and conveyors. These motors TM21-L. Both series can be customized with different top
offer higher efficiency and higher power factor than any enclosures for selected types of protection and cooling. The
previous design. The TM21-M and TM21-L have rugged arrows in the illustrations below indicate airflow.

Totally-Enclosed Air-Water- Totally-Enclosed Air-Air Open Drip Proof Type ODP/IP22

Cooled Type TEWAC/IP55 Cooled Type TEAAC/IP55 A drip-proof type motor has a
Includes an air-to-water heat In a corrosive or harmful cooling air intake and hot air
exchanger in the air housing environment, a totally-enclosed exhaust window located at the
above the motor. fan-cooled motor can be applied. top of the hood.
An external fan directs fresh
A drain in the air housing protects air through the pipes in the air Openings are covered by screens
the motor from damage caused housing above the motor. The and enclosure is constructed to
by water leakage. pipes serve as a heat exchanger prevent intrusion of water drips
in which outside fresh air passing and other foreign materials into
through cools the hot air inside. the motor and meets NEMA WP-I
requirements.

NEMA Weather-Protected WPII/IP24

This motor is designed for outdoor
operation. The air housing is in
accordance with NEMA WPII, and
features three right-angled turns for
air intake, dropping velocity below
3 m/sec (600 ft/min.), trapping water,
dust, and foreign materials.

TM21-M TM21-L Fundamental Building Block 21-M and 21-L

Power 50 HZ 160 - 2,800 kW 450 - 16,500 kW
• IC01, IC61 and IC81W cooling per IEC Standard
(210 - 3,750 hp) (600 - 22,000 hp)
construction are available by changing the top-
60 HZ 200 - 3,550 kW 450 - 18,500 kW mounted air housing.
(270 - 4,750 hp) (600 - 25,000 hp) • The main terminal box can be rotated every 90°,
Voltage 2 kV - 11 kV 2 kV - 13.8 kV and is large enough for easy cable connection.
• International standards such as IEC, NEMA,
Speed Up to 3,600 rpm Up to 3,600 rpm BS, AS, etc.
• Optional classified areas: Exn, Exe, Exp, Extd
Poles From 2 up to 10 From 2 up to 24 • Insulation Class F, B Rise design is standard

Rotor Aluminum Casting Copper Bar

6
High-Speed Induction Motors
Rotor – Squirrel cage with aluminum rotor bars specially
designed with stiff-shaft low vibration
Stator – Two pole windings, spring mounted for vibration
isolation
Bearings – Oil-fed sleeve bearings or Magnetic bearings
Data for typical high speed induction motors are shown
below.

Power Up to 8000 kW

Supply Voltage 2.3-11 kV

Poles/Speed 2 Poles/to 12,000 rpm

Totally Enclosed Water to
11,900 rpm, 1.8 MW, Induction Motor Enclosure Air Cooling TEWAC/IP55 or
Air to Air TEAAC/IP55
For very high speeds, induction motors are used. These are
custom designed for special applications such as driving Classified Areas Exn, Exe, or Exp Protection
gearless compressors.
Available
IEC, NEMA, BS, AS
Standards

High Speed Motor and Drive Systems

TMEIC’s unique capabilities in designing high speed motors for direct-drive
solutions eliminate speed increasing gearboxes or mechanical clutches.
The net result of this solution is lower cost, smaller footprint, higher system
efficiency, smaller parts and spares inventory to maintain, and worry-free
service.

Conventional Solution Direct-Drive Solution

TMEIC TMEIC TMEIC unique spring-mounted

Adjustable Speed Drive Adjustable Speed Drive stator design reduces vibration

Standard Low Speed

Compressor
Motor Motor
Speed
Decreasing Compressor
Gear
7
Medium-High Power Synchronous Motors
TMEIC custom designs and builds medium and high
power synchronous motors for special applications such
as driving mills, blowers, pumps and compressors. The
example shown here is a 53 MW synchronous motor
for a steel mill blower. It runs at 3,000 rpm with a 10 kV
supply. Data for typical synchronous motors are shown
below.

2000 kW up to 80 MW, either

Power
Utility Fed or VFD Powered
Supply Voltage 3.3-13.8 kV

Poles/Speed Up to 34 Poles/Up to 3,600 rpm Up to 3,600 rpm, 53 MW, Synchronous Motor

Totally Enclosed Water to

Air Cooling TEWAC/IP55 or Rotor – Cylindrical solid rotor for 2 pole, salient pole for 4
Enclosure
TEAAC/IP55 – Other Enclosures to 34 poles
Available
Bearings – Oil-fed sleeve bearings
Classified Areas Exn/Exp Protection Available
Available Sync Brush Type, DC Brushless,
Field Designs AC Brushless

Low Speed Induction Machines

TMEIC’s unique capabilities in designing low speed motors for
direct-drive solutions eliminate speed decreasing gearboxes or
mechanical clutches. The net result of this solution is lower cost,
smaller footprint, higher system efficiency, lower parts and spares
inventory to maintain, and worry-free service.

Advantages
• Cost savings – individual approval tests & expensive full load
tests eliminated
• Reduced testing requirements lowers delivery time
• Simpler Exn designs reduce machine costs (when compared to
alternative inner pressurized or flammable enclosures)
• Lower cost of ownership – eradication of the air supply system
required for inner pressurized machines minimizes maintenance
and operating cost

Special Features SAG Mill and Motor

• High efficiency saves energy
• Low vibration and noise
• High reliability
• Meet international standards such as IEC, EN, BS, NEMA
• Easy installation
• Quick delivery

8
Large High-Speed 2-Pole Synchronous Motors
TMEIC builds a range of custom designed, high-speed,
high-power synchronous motors for driving large
compressors.

The example on the left shows a 25 MW synchronous

motor designed for variable speed operation from 2,500 to
3,780 rpm with a 7 kV variable frequency drive.

Other TMEIC designs are available for synchronous motor

top speeds up to 6200 rpm. This can allow large compressors
to be driven without a gearbox.

High Speed 25 MW 3,780 rpm Synchronous Motor

Design
Power Feature
– Motor output levels up to 80 MW (107,200 hp)
are available, and speeds up to 6,200 rpm when used Power 60 HZ 15 MW (20,100 hp) up to
with a matched variable frequency drive such as the 80 MW (107,200 hp)
TMEIC TMdrive®-XL85.
Supply Voltage 3.3 kV to 13.8 k V
Rotor – The rotor is a two pole, cylindrical design with a
shaft mounted brushless exciter. Totally Enclosed Water to Air
Enclosure
Cooled – TEWAC/IP55
Bearings and Maintenance – Oil lubricated sleeve
Exp certification for use in
bearings are used. No slip rings are required with the
hazardous ares Zone 1 & 2, us-
brushless exciter. Classified Areas
ing an internal pressurization
system
Quality Manufacturing and Standards – TMEIC’s motor
manufacturing is certified to ISO 9001 and ISO 14001. Motor Speed Up to 6,500 rpm
Motors can be certified by third party agencies such as
CSA, Lloyd’s and Baseefa. Motors can be designed to Insulation Class Class F
international standards such as IEC, NEMA, BS, and AS.

Air-water Heat Motor Cooling uses a water-air heat

Exchanger exchanger with two shaft-mounted
fans forcing cool air inwards through
the rotor and windings

Stator Coils

Oil-fed Sleeve Bearing

Cooling Fan

Brushless Exciter has a rotor

Stator Core mounted three-phase winding,
which feeds high reliability
diodes on the shaft supplying
Cylindrical Rotor DC power to the rotor field
winding.
High-Speed Synchronous Motor – Internal Details

9
Hazardous Area Protection and
Low & Medium Voltage Motors
Types of Explosion Protected Machines

TMEIC provides motors with different levels of explosion protection for a range of operating environments found in the
process industries, in particular the Oil & Gas industry. Protection in dust environments, Zone 22, is available as ExtD
according to IEC61241-1.
Exn – Non-Sparking - Machines which, in Exp – Inner Pressurized - Explosive gas that may
normal operation, are not capable of igniting cause ignition is excluded from the inside of the
a surrounding explosive atmosphere. machine. The motor housing is pressurized with
air to ensure no gases enter.
Exe – Increased Safety - Machines that Exd – Flame Proof Enclosure - Machines are
do not produce dangerous sparks or constructed to contain an internal explosion and
temperatures in normal service or starting. prevent the transmission of flame to the external
Special increased safety measures are taken. atmosphere. The temperature of operation is
such that it cannot ignite the surrounding gas.

Global Protection and Certification

Explosion protection certification for TMEIC’s motors has been obtained around the world, as illustrated in this table.
USA UK Europe China Korea Russia Australia Canada Others

Standard NEC EN EN + ATEX GB IEC or KS IEC or AS IEC or GOST CSA IEC or EN

Certification FM, UL, Baseefa, TestSafe

Baseefa CQST KOSHA CCVE CSA Baseefa
Body etc. PTB, etc. Baseefa
Exd, Exp, Exd, Exp, Exd, Exp, Exd, Exp, Exd, Exp, Exp Exd, Exp,
Records Exd Exn
Exe, Exn Exe, Exn Exe, Exn Exe, Exn Exe, Exn Exn Exe, Exn

TM21-FII Series Totally Enclosed Fan Cooled Low and Medium Voltage Motors

TM21-FII Series motors are widely applied in industrial applications such as small and medium size fans, blowers,
compressors, pumps, and conveyors. They are tough and suitable for harsh conditions.
Power – The TM21-FII series power output ranges from Bearings and Maintenance – Ball and roller bearings or
37 kW (50 hp) to 1400 kW (1,850 hp). With a choice of oil lubricated sleeve bearings are applied based on rating
poles, the series provides a selection of speeds from 720 and application requirements. Optimized design makes
rpm up to 3,600 rpm. re-greasing simple.
Frame – The TM21-FII series have a cast iron fin frame Quality Manufacturing and Standards – TMEIC manufacturing
with improved ventilation flow. is certified to ISO 9001 and ISO 14001. Motors can be certified
Rotor – The squirrel cage rotor is a highly-reliable by third party agencies such as Lloyd’s, CSA, Baseefa, and
aluminum die-casting. etc. Motors can be designed to international standards such
as IEC, NEMA, BS, AS, etc.

37 kW (50 hp) up to Terminal

Power Output Stator Core Box
1400 kW (1,850 hp)
Number of Poles 2 P up to 10 P Stator Rotor
Coil Core
Supply Voltage Up to 6,600 V
Totally Enclosed Fan Cooled:
Enclosure Ball
TEFC/IP55 Fan
Bearing
Classified Areas Exn, Extc, Exd Cover

Frame Size 250 ~ 500 (IEC basis)

Temperature Rat- Class F insulation, Class B design
ings Optional Class F and Class F Rise Shaft

10
TM21-FII –Totally Enclosed Fan Cooled Internal Details
Generators – Diesel and Turbine Driven
TMEIC produces a range of high-quality, custom
designed generators for power by turbines or diesels.
The four-pole designs provide power levels up to
50,000 kVA at 50 or 60 Hz, 1500 rpm or 1800 rpm.
Higher speed two-pole generators provide power
levels up to 100,000 kVA.

Reliability - All generators are built in the same plant

as, and to the same high standards as the large motors.
Manufacturing procedures to obtain the highest
reliability include Vacuum Pressure Impregnation of the
insulation, employing a forged rotor with integral pole
bodies for the maximum shaft rigidity and higher critical
speed, and accurate rotor shaft balancing.

Maintenance - Easy maintenance is realized using a

brushless AC exciter with a permanent magnet generator.
The oil-fed sleeve bearings employ a floating labyrinth
seal to prevent leakage, and positive internal pressure to
1 Rotor Shaft 10 Frame
prevent oil entering the generator.
2 Bracket 11 Air Cooler Cover
3 Bearing With Insulation 12 Air Cooler The cutaway drawing in the upper left shows a typical
4 Fan 13 Stator Core four-pole generator with top mounted air cooler and
5 Fan Guide 14 Stator Coil water heat exchanger.
6 Main Terminal Box 15 Exciter Support
7 Rotor Coil 16 Rotary Rectifier
8 Pole Head 17 AC Exciter
9 Rotor Coil Bracket 18 PMG

TM21-TG

Type Two-pole, 5,000 to 100,000 kVA power Type Four-pole, 10,000 to 50,000 kVA power
Rotor Solid cylindrical rotor Rotor Salient pole solid rotor
Voltage Rated 11 kV, 13.8 kV Voltage Rated 6.6 kV, 11 kV, 13.8 kV
Speed 3,000 rpm or 3,600 rpm Speed 1,500 rpm or 1,800 rpm
Frequency 50 or 60 Hz Frequency 50 or 60 Hz
Power Factor 85% lagging Power Factor 80~90% lagging
Totally enclosed, water to air cooled Totally enclosed, water to air cooled
Enclosure Enclosure
(TEWAC) (TEWAC)
Insulation Rating F-Class insulation Insulation Rating F-Class insulation
Excitation Brushless exciter with PMG Excitation Brushless exciter with PMG
Bearings Sleeve bearings, oil lubricated Bearings Sleeve bearings, oil lubricated
Oil 0.1 Mpa bearing pressure Oil 0.1 Mpa bearing pressure

11
Global Support
Wherever You Are, We Are Right
NORTH
AMERICA
Next Door
E U R O P E
London
A S I A
TMEIC has the capability to provide world-
Bari Beijing PA C I F I C
OCEAN
wide service support with trained field
Roanoke, VA Yancheng
PA C I F I C
OCEAN Houston, TX Head Office AT L A NT I C
OCEAN Guangzhou
TOKYO service engineers. Spare parts depots are
Dubai Hong Kong
Mumbai Kaohsiung
Hyderabad
Shanghai, China
TMEIC Asian Spare Parts Depot strategically located close to main industrial
Bangalore
AFRICA
Singapore
centers.
INDIAN
OCEAN Jakarta
SOUTH
AMERICA In Asia & Pacific: Customers are supported
Sao Paulo
AUSTRALIA
by TMEIC service personnel and the TMEIC
factory in Japan.

In North America: Customers are supported

by TMEIC factory service personnel from
Roanoke, Virginia.
Sales and Service Offices
In Europe: Customers are supported by
Spare Parts Depots TMEIC European service personnel.
Tokyo, Japan
Headquarters TMEIC Head Office
& Factory Motor and Generator Service: EASA and IPS
Service Centers support TMEIC motors and
generators across North America.

Global Office Locations:

TMEIC Corporation Toshiba Mitsubishi-Electric Industrial Systems (China) Corp.
Office: 1325 Electric Rd., Roanoke, VA, 24018, U.S.A. Beijing China; Tel.: +86 10 5873-2277; Fax: +86 10 5873-2208
Mailing: 2060 Cook Drive, Salem, VA, 24153, U.S.A. Email: [email protected]
Tel.: +1-540-283-2000; Fax: +1-540-283-2001 Shanghai Branch: Shanghai Works
Email: [email protected]; Web: www.tmeic.com Tel: +86-21-69925007; Fax: +86-21-69925065
Houston Branch: Houston, TX;
Yangcheng TMEIC Power Electronics Corporation
Tel: +1-832-767-2680; Email: [email protected]
Yangcheng, Jiangxi, China
TMEIC Power Electronics Products Corporation
Shanghai Bao-ling Electric Control Equipment Co., Ltd.
Factory: 6102 North Eldridge Parkway, Houston, TX 77041
Shanghai, China; Tel: +86-21-5660-3659; Fax: +86-21-5678-6668
Mailing: 13131 W. Little York Road, Houston, TX 77041
Guangzhou Toshiba Baiyun Ryoki Power Electronics Co., Ltd.
TMEIC–Sistemas Industriais da América do Sul Ltda. Guangzhou, China; Tel: +86-20-2626-1625 Fax: +86-20-2626-1290
São Paulo/SP, Brazil
Tel: +55-11-3266-6161; Fax: +55-11-3253-0697 TMEIC Asia Company Limited
Hong Kong, China; Tel: +852-2243-3221; Fax: +852-2795-2250
Toshiba Mitsubishi-Electric Industrial Systems Corp. Singapore Branch: Tel: +65-6292-7226 FAX: +65-6292-0817
Tokyo, Japan; Tel: +81-3-3277-5511; Web: www.tmeic.co.jp Taiwan Office: Tel: +886-7-2239425 Fax: +886-7-2239122
TMEIC Europe Limited P.T. TMEIC Asia Indonesia
Uxbridge, Middlesex, United Kingdom Jakarta; Tel: +62-21-2966-1699; Fax: +62-21-2966-1689
Tel.: +44 870 950 7220; Fax: +44 870 950 7221
Email: [email protected]; Web: www.tmeic.com/europe TM21 is a trademark of TOSHIBA MITSUBISHI-ELECTRIC
INDUSTRIAL SYSTEMS CORPORATION.
TMEIC Industrial Systems India Private Limited TMdrive is a trademark of TOSHIBA MITSUBISHI-ELECTRIC
Hyderabad, India; INDUSTRIAL SYSTEMS CORPORATION.
Tel.: +91-40-4434-0000; Fax: +91-40-4434-0034
All other products mentioned are registered trademarks and/or trademarks of their
Web: www.tmeic.in; Email: [email protected]
respective companies.
Mumbai Branch: Mumbai, Maharashtra, India
All specifications in this document are subject to change without notice.
Tel: +91-22-6155-5444; Fax: +91-22-6155-5400 This brochure is provided free of charge and without obligation to the reader or to
TMEIC Power Electronics Systems India Private Ltd. TMEIC Corporation, and is for informational purposes only. TMEIC Corporation does
Bangalore, India, not accept, nor imply, the acceptance of any liability with regard to the use of the
information provided. TMEIC Corporation provides the information included herein as
Tel: +91-80-6746-6000; Fax: +91-80-6746-6100
is and without warranty of any kind, express or implied, including but not limited to
any implied statutory warranty of merchantability or fitness for particular purposes. The
brochure is not an implied or express contract.
P-0023
© 2012 TMEIC Corporation. All Rights Reserved. June 2019