Scribd Logo
Upload

Welcome to Scribd!

  • 16 views

    CP 300 (A) - QCP-036 Construction of Hospital Transformer Room

    Uploaded by

    tarek
    This document provides a method statement for constructing part of the external walls around a hospital transformer room area using reverse formwork and single-sided forms. It involves casting a sacrificial blinding concrete wall against the excavation face and using that as one side of the reinforced concrete wall. The steps include: (1) excavating and preparing the foundation area, (2) installing reverse formwork and casting blinding concrete up to 1220mm height, (3) removing forms and waterproofing the blinding wall, (4) installing polyethylene sheeting and casting the foundation, (5) installing single-sided forms and reinforcing for the external wall. Responsibilities and safety compliance are also outlined.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    CP 300 (A) - QCP-036 Construction of Hospital Transformer Room

    Uploaded by

    tarek
    16 views6 pages
    This document provides a method statement for constructing part of the external walls around a hospital transformer room area using reverse formwork and single-sided forms. It involves casting a sacrificial blinding concrete wall against the excavation face and using that as one side of the reinforced concrete wall. The steps include: (1) excavating and preparing the foundation area, (2) installing reverse formwork and casting blinding concrete up to 1220mm height, (3) removing forms and waterproofing the blinding wall, (4) installing polyethylene sheeting and casting the foundation, (5) installing single-sided forms and reinforcing for the external wall. Responsibilities and safety compliance are also outlined.

    Original Title

    CP 300(a)-QCP-036 Construction of Hospital Transformer Room

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a method statement for constructing part of the external walls around a hospital transformer room area using reverse formwork and single-sided forms. It involves casting a sacrificial blinding concrete wall against the excavation face and using that as one side of the reinforced concrete wall. The steps include: (1) excavating and preparing the foundation area, (2) installing reverse formwork and casting blinding concrete up to 1220mm height, (3) removing forms and waterproofing the blinding wall, (4) installing polyethylene sheeting and casting the foundation, (5) installing single-sided forms and reinforcing for the external wall. Responsibilities and safety compliance are also outlined.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    16 views6 pages

    CP 300 (A) - QCP-036 Construction of Hospital Transformer Room

    Uploaded by

    tarek
    This document provides a method statement for constructing part of the external walls around a hospital transformer room area using reverse formwork and single-sided forms. It involves casting a sacrificial blinding concrete wall against the excavation face and using that as one side of the reinforced concrete wall. The steps include: (1) excavating and preparing the foundation area, (2) installing reverse formwork and casting blinding concrete up to 1220mm height, (3) removing forms and waterproofing the blinding wall, (4) installing polyethylene sheeting and casting the foundation, (5) installing single-sided forms and reinforcing for the external wall. Responsibilities and safety compliance are also outlined.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 6

    J&P Document number:

    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 1 of 6
    J&P–AVAX S.A. J.V.

    Document Title:

    METHOD STATEMENT
    CONSTRUCTION OF HOSPITAL TRANSFORMER ROOM WALL USING REVERSE
    FORMWORK

    Issue Date : 02-10-2005

    Revision Date: 02-10-2005 Revision No. : 0

    Issued By : QA/QC Engineer:

    Approved By : Deputy Project Manager:

    Approved By : Senior Project Manager:

    F-P.810/1-0
    J&P Document number:
    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 2 of 6
    J&P–AVAX S.A. J.V.

    1. SCOPE

    This Method Statement covers the works required to construct part of


    the external walls around the Hospital Transformer Room area using
    external reverse wall formwork and single sided main external wall forms
    due to external wall exterior working space restrictions. The works and
    materials shall conform to the requirements of Contract IFC Drawings,
    approved Shop Drawings and Project Specifications.

    2. FIELD OF APPLICATION

    The area affected is in between Grids HO/T-HO/U & HO/18-HO/20, with


    the reverse external formwork being used between base of the Mat
    Foundation and the existing ground surrounding the Hospital Basement
    excavation. Wherever the reverse formwork is used at the external wall
    location, the internal face of the basement external wall will be
    constructed using a single sided interior form.

    The system of work involves casting a sacrificial blinding concrete wall


    against the face of the excavation, extending out to the external face of
    the final reinforced concrete external Basement wall. Then by using this
    blinding concrete wall as one side of the final reinforced concrete wall,
    construct the reinforced concrete wall using a single sided form on the
    internal face (within the Basement).

    3. REFERENCES

    3.1 Project Specifications


    Section 3100 Concrete Formwork

    3.2 Project Specifications


    Section 3200 Concrete Reinforcement

    3.3 Project Specifications


    Section 3300 Cast-in-place Concrete

    3.3 Qatar Construction Specifications (QCS)


    Section 5 Concrete

    3.4 Drawing No. S-1B1A(RB) Rev. 3 (IFC; Hospital)


    Footing Basement Floor Framing Plan (Area A)

    F-P.810/1-0
    J&P Document number:
    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 3 of 6
    J&P–AVAX S.A. J.V.

    4. MATERIALS

    4.1 OPC 20/20 & OPC 40/20


    Material Submittal No. CP300(a)-MS-03/005 Rev. 01 & 02 (Code
    B)

    4.2 Dermaprimer Liquid Solvent Based Bituminous Primer


    Material Submittal No. CP 300(a)-MS-HOS-07-077 (Code A)
    (Product Data Sheet attached; Health & Safety also covered)
    * Primer for Adesobit 1600 Waterproofing Membrane

    4.3 Adesobit 1600 Waterproofing Membrane


    Material Submittal No. CP 300(a)-MS-HOS-07-077 (Code A)
    (Product Data Sheet attached; Health & Safety also covered)

    5. TOOLS/EQUIPMENTS

    5.1 Crane

    5.2 Formworks & Accessories

    6. RESPONSIBILITIES ON SITE

    6.1 External wall construction works and related activities shall be


    undertaken by a dedicated group headed by a Foreman under the
    over-all supervision of a Site Engineer.

    6.2 The responsible Site Engineer shall raise the necessary Request
    for Inspections (RFI) for Blinding Concrete, Reinforcement
    Inspection, Concreting, Bitumen Application and Waterproofing
    Membrane Installation.

    6.3 The responsible Site Engineer shall ensure compliance of the


    work with this Method Statement and Project Specifications.

    6.4 Health, Safety and Environmental issues shall be addressed in


    accordance with the approved HSE Plan (Document Submittal
    No. CP 300(a)- DS-BOTH-01 /008) under the supervision of the
    Site Safety Officers.

    7. WORK PROCEDURE

    7.1 Complete all Mat Foundation related excavation, debris removal,


    termite treatment, and horizontal concrete blinding.

    F-P.810/1-0
    J&P Document number:
    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 4 of 6
    J&P–AVAX S.A. J.V.

    7.2 Set out external face of Mat Foundation on concrete blinding.

    7.3 Install reverse vertical formwork on blinding 5mm outside edge


    line of Mat Foundation to a minimum height of 1220mm. Install
    stop-end at limits of reverse form works.

    7.4 Concrete to external side of vertical reverse formwork using


    blinding concrete mix (OPC 20/20) to a minimum of 1220mm
    height (do not cure vertical blinding concrete with water).

    7.5 Vertically extend or lift vertical reverse formwork and concrete


    (blinding) full height or in lifts to the external side of reversed
    formwork until top of external vertical blinding concrete is level
    with existing external ground (do not cure vertical blinding
    concrete with water). In the last lift of this blinding concrete wall,
    install 20mm dia. HY rebars at 1m intervals (“U” bars – inverted –
    minimum 800mm each leg) at top of final lift of vertical blinding
    concrete wall (exposed top of bars to be used to assist in
    securing the single sided internal formwork of the reinforced
    concrete external wall at a later stage).

    7.6 Remove all reverse formwork and clean area.

    7.7 Apply Dermaprimer Liquid Solvent Based Bituminous Primer and


    install Adesobit 1600 Waterproofing Membrane against base of
    externally cast vertical blinding concrete wall, extending the
    membrane system a minimum of 200mm onto the Mat
    Foundation blinding and at least 2m up the vertical blinding
    concrete wall. At ends of reverse formwork area, extend
    waterproofing sheet a minimum of 200mm past end of vertical
    stop-end position, retaining the protective strip to the membrane
    on the vertical sheeting outside the line of the vertical stop-end
    positions. No waterproofing system protection board to be applied
    to the membrane affixed to the external vertical blinding concrete
    wall. Application of bitumen and installation of waterproofing
    membrane shall be in accordance with Method Statement on
    Concrete Protection & Waterproofing (Document Submittal No.
    CP300(a)-DS-BOTH-07-066; Code B).

    7.8 Install polyethylene sheeting over Mat Foundation blinding


    concrete, and extend the sheeting at least 300mm up the
    waterproofed external vertical blinding concrete wall.

    F-P.810/1-0
    J&P Document number:
    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 5 of 6
    J&P–AVAX S.A. J.V.

    7.9 Fix Mat Foundation rebar/wall starters/wall kicker/waterbar


    without puncturing the exposed vertical waterproofing membrane.

    7.10 Cast Mat Foundation, taking care not to damage the exposed
    vertical waterproofing membrane.

    7.11 Cast adjacent column pedestals on the completed Mat


    Foundations.

    7.12 Complete the vertical waterproof membrane to the top of the


    vertical blinding concrete wall, leaving at least 200mm of
    waterproof membrane above the top of the vertical concrete wall
    (all membrane above the top of the wall is to have the protective
    covering maintained).

    7.13 Prepare wall kicker top surface, and install rebar/waterbar/single


    sided formwork to external reinforced concrete wall (including
    vertical stopends) to a minimum height level with the top of the
    vertical blinding concrete wall. The first concreting lift of the
    reinforced concrete wall is to be only to the top of the previously
    cast external vertical concrete blinding. Install external kicker for
    external reinforced concrete wall at top of vertical blinding
    concrete wall. The single sided form can be braced using props
    from the completed adjacent column pedestals and/or temporary
    ballast blocks, along with ties connected to the previously cast
    inverted “U” bars in top of vertical blinding concrete wall.

    7.14 Cast single sided formed external reinforced concrete wall at a


    slow rate in order not to place excessive pressure on the single
    sided formwork (check form design for rate of casting).

    7.15 Water cure reinforced concrete external wall in accordance with


    Method Statement on Curing of Concrete Structures (Document
    Submittal No. CP300(a)-DS-BOTH-03-026; Code B).

    7.16 Following casting of the single sided forms to the reinforced


    concrete external wall, adjacent wall to the ends/above the single
    sided cast wall can be completed in the usual manner using
    double sided formwork. Waterproofing membrane will be
    exposed at all external sides of the single sided cast reinforced
    concrete external wall enabling continuance of the waterproofing
    system.

    8. SAFETY PROCEDURES

    F-P.810/1-0
    J&P Document number:
    M ET H O D CP 300(a)-QCP-036
    S T AT E M E N T
    J&P (O) Ltd. /
    Page: 6 of 6
    J&P–AVAX S.A. J.V.

    8.1 The Site Engineer shall physically inspect the working area to
    confirm that it is cleared of any hazard and/or obstructions that
    may hinder access or proper execution of the work.

    8.2 The Site Engineer shall ensure that all personnel engaged in
    column demolition works and related activities are wearing the
    required Personal Protective Equipments (PPE).

    8.3 Protect top of excavations in work area.

    8.4 Ensure that wall concreting operation have suitable concreting


    platforms protecting workers from falling.

    8.5 Ensure that access/egress to/from each area of work is safe,


    including adequate lighting during evening activities.

    8.6 Ensure that surrounding areas are kept clean of


    debris/unnecessary materials/equipment.

    8.7 Health, Safety and Environmental issues shall be addressed in


    accordance with the approved HSE Plan (Document Submittal
    No. CP 300(a)- DS-BOTH-01 /008).

    9. REVISIONS

    Rev. 0 Date: 02-Oct-05

    F-P.810/1-0

    You might also like