Scribd Logo
Upload

Welcome to Scribd!

  • 36 views

    IDS Strip Beam Guide

    Uploaded by

    Ercykizzy beat maker
    The document provides information on the features and setup of Selco multi-beam sensors. It describes the key features, including that two blocked beams are needed to trigger an alarm, adjustable brackets for alignment, and an IP54 rating. Diagrams show the PCB layout, including the tilt switch and connections. Instructions are given for wiring the sync wire and power, installing single, double, or multiple beams, selecting the detection range, physical installation, and aligning the transmitter and receiver.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    IDS Strip Beam Guide

    Uploaded by

    Ercykizzy beat maker
    36 views6 pages
    The document provides information on the features and setup of Selco multi-beam sensors. It describes the key features, including that two blocked beams are needed to trigger an alarm, adjustable brackets for alignment, and an IP54 rating. Diagrams show the PCB layout, including the tilt switch and connections. Instructions are given for wiring the sync wire and power, installing single, double, or multiple beams, selecting the detection range, physical installation, and aligning the transmitter and receiver.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides information on the features and setup of Selco multi-beam sensors. It describes the key features, including that two blocked beams are needed to trigger an alarm, adjustable brackets for alignment, and an IP54 rating. Diagrams show the PCB layout, including the tilt switch and connections. Instructions are given for wiring the sync wire and power, installing single, double, or multiple beams, selecting the detection range, physical installation, and aligning the transmitter and receiver.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    36 views6 pages

    IDS Strip Beam Guide

    Uploaded by

    Ercykizzy beat maker
    The document provides information on the features and setup of Selco multi-beam sensors. It describes the key features, including that two blocked beams are needed to trigger an alarm, adjustable brackets for alignment, and an IP54 rating. Diagrams show the PCB layout, including the tilt switch and connections. Instructions are given for wiring the sync wire and power, installing single, double, or multiple beams, selecting the detection range, physical installation, and aligning the transmitter and receiver.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Training

    Multi Beam
    Features

     Two adjacent beams must be blocked for an alarm to be triggered


     Buzzer for easy setup
     Swivel brackets for easy alignment
     Very good antiglare, light immunity
     Anti-tilt switch
     IP54 rating

    IDS Training Selco Strip Beams v3 | Features 1


    PCB

    Below are diagrams of the Selco multi-beam PCBs showing the tilt switch and the connectors for the
    transmitter and receiver.

    The tilt switch when operational


    will cause the multi-beam to
    trigger if tilted more than 45
    degrees

    Tilt Switch
    Buzzer
    JP3 Enable/Disable
    On = Tilt switch has no effect
    Off = Tilt switch operational

    Alarm
    ouput

    Sync
    output

    Tx 12V DC
    Rx

    Tamper
    Range output
    Selector

    Sync
    output

    12V DC

    Tamper
    output

    2 PCB | IDS Training Selco Strip Beams v3


    Sync Wire Connection

    The sync must be connected between the receiver and the transmitter for the beams to work.

    Tx
    Rx

    12V Power Connection

    The voltage on the Tx must not be lower than the Rx

    Single beam instalation

    Two beam installation


    Tx Rx Rx Tx

    IDS Training Selco Strip Beams v3 | PCB 3


    Multi beam installation
    Tx Rx Rx Tx Tx Rx Rx Tx

    Range Selection
    When using beams to cover a distance less than the maximum rated distance to get the best results set SW3.

    L = Low
    M = Medium
    H = High (Rated distance)

    Physical Installation

    The beam must have the correct end caps in the correct places.

    TOP
    No holes to seal the
    detector

    Please do not swop end caps

    Bottom Connector always at


    Holes for moisture the bottom
    draining

    4 PCB | IDS Training Selco Strip Beams v3


    Alignment
    Alignment steps

    Aim the Tx & Rx at each other Turn Rx 90 degrees to left

    1 Rx Tx 2 Rx Tx

    Power beams up. Beams will Align Rx with the Tx. The buzzer will

    3 4
    sound for self-inspection. Then beep slower and when aligned a
    the buzzer beep faster long beep will sound

    Rx Tx Rx Tx

    Repeat by turning the Rx to the Repeat Alignment step

    5 6
    right

    Tx Rx Tx
    Rx

    IDS Training Selco Strip Beams v3 | Alignment 5

    You might also like