Microwave Radio
Microwave Radio
Microwave Radio
Standards
In the United States, radio channel assignments are controlled by the Federal Communications Commission (FCC) for commercial carriers and by the National Telecommunications and Information Administration (NTIA) for government systems. The FCC's regulations for use of spectrum establish eligibility rules, permissible use rules, and technical specifications. FCC regulatory specifications are intended to protect against interference and to promote spectral efficiency. Equipment type acceptance regulations include transmitter power limits, frequency stability, out-of-channel emission limits, and antenna directivity. The International Telecommunications Union Radio Committee (ITU-R) issues recommendations on radio channel assignments for use by national frequency allocation agencies. Although the ITU-R itself has no regulatory power, it is important to realize that ITUR recommendations are usually adopted on a worldwide basis.
Historical Milestones
1950s Analog Microwave Radio
Used FDM/FM in 4, 6, and 11 GHz bands for long-haul Introduced into telephone networks by Bell System
Replaced analog microwaves Became bandwidth efficient with introduction of advanced modulation techniques (QAM and TCM) Adaptive equalization and diversity became necessary for high data rates
Digital microwave used for cellular back-haul Change in MMDS and ITFS spectrum to allow wireless cable and point-to-multipoint broadcasting IEEE 802.16 standard or WiMax introduces new application for microwave radio Wireless local and metro area networks capitalize on benefits of microwave radio
Microwave Link Structure. The basic components required for operating a radio link are the transmitter, towers, antennas, and receiver. Transmitter functions typically include multiplexing, encoding, modulation, up-conversion from baseband or intermediate frequency (IF) to radio frequency (RF), power amplification, and filtering for spectrum control. Receiver functions include RF filtering, down-conversion from RF to IF, amplification at IF, equalization, demodulation, decoding, and demultiplexing. To achieve point-to-point radio links, antennas are placed on a tower or other tall structure at sufficient height to provide a direct, unobstructed lineof-sight (LOS) path between the transmitter and receiver sites.
Microwave System Design. The design of microwave radio systems involves engineering of the path to evaluate the effects of propagation on performance, development of a frequency allocation plan, and proper selection of radio and link components. This design process must ensure that outage requirements are met on a per link and system basis. The frequency allocation plan is based on four elements: the local frequency regulatory authority requirements, selected radio transmitter and receiver characteristics, antenna characteristics, and potential intrasystem and intersystem RF interference. Microwave Propagation Characteristics. Various phenomena associated with propagation, such as multipath fading and interference, affect microwave radio performance. The modes of
propagation between two radio antennas may include a direct, line-of-sight (LOS) path but also a ground or surface wave that parallels the earth's surface, a sky wave from signal components reflected off the troposphere or ionosphere, a ground reflected path, and a path diffracted from an obstacle in the terrain. The presence and utility of these modes depend on the link geometry, both distance and terrain between the two antennas, and the operating frequency. For frequencies in the microwave (~2 30 GHz) band, the LOS propagation mode is the predominant mode available for use; the other modes may cause interference with the stronger LOS path. Line-ofsight links are limited in distance by the curvature of the earth, obstacles along the path, and freespace loss. Average distances for conservatively designed LOS links are 25 to 30 mi, although distances up to 100 mi have been used. For frequencies below 2 GHz, the typical mode of propagation includes non-line-of-sight (NLOS) paths, where refraction, diffraction, and reflection may extend communications coverage beyond LOS distances. The performance of both LOS and NLOS paths is affected by several phenomena, including free-space loss, terrain, atmosphere, and precipitation.
Adapts to difficult terrain Loss versus distance (D) = Log D (not linear) Flexible channelization Relatively short installation time Can be transportable Cost usually less than cable No back-hoe fading
Weaknesses
Paths could be blocked by buildings Spectral congestion Interception possible Possible regulatory delays Sites could be difficult to maintain Towers need periodic maintenance Atmospheric fading
potential for microwave as wireless systems grow. Increases in spectrum allocations and advances in spectrum efficiency through technology have created business opportunities in the field of microwave radio. Telecommunications carriers, utility companies, and private carriers all use microwave to complement wired and optical networks.
Courses
If you need a short but intensive overview of this field, considerMicrowave and Fixed Line-of-Sight Link Design Principles, a two-day course. For those who need a less technical discussion of microwaves, for instance sales and management personnel, a friendly version of the above two-day course is also available. If your needs require a more detailed course on microwaves, please take a look at Microwave and Fixed Line-of-Sight Link Design Workshop, a comprehensive four-day course which offers the option to add a hands-on workshop on the fifth day.
Books
o
o o o
Digital Transmission Systems, Second Edition, by David R. Smith. Kluwer Academic Publishers, 2004. Good introduction to microwave systems, including modulation, error correction codes, equalization, and diversity. Microwave Radio Links: Theory to Design by Carlos Salema. John Wiley and Sons, 2000. Excellent treatment of all aspects of microwave systems engineering. Federal Communications Commission Rules and Regulations, Part 101, Fixed Microwave Services, 1 August 1996. TIA/EIA Telecommunications Systems Bulletin, TSB10-F,Interference Criteria for Microwave Systems, June 1994.
Web Resources
o o o o o o
ITU (www.itu.int) ITU-T: Telecom sector of the International Telecommunications Union, the United Nations agency that sets telecommunications standards. ANSI (www.ansi.org): The US national standards body. Coordinates and accredits standards development across the US. IEEE (www.ieee.org). US-based international professional association of electrical engineers. Develops standards and submits to ANSI for approval. ETSI (www.etsi.org) European Telecommunication Standards Institute. http://members.shaw.ca/propagation/models.html. Here you will find many Public domain products for LOS design http://www.comsearch.com/industry_solutions/software/mw_design.jspHere you will commercial tools for microwave design.