Lab - Design and Implement a VLSM Addressing Scheme

Topology

Objectives
Part 1: Examine Network Requirements
Part 2: Design the VLSM Address Scheme
Part 3: Cable and Configure the IPv4 Network

Background / Scenario
Variable Length Subnet Mask (VLSM) was designed to avoid wasting IP addresses. With VLSM, a network is
sub netted and then re-sub netted. This process can be repeated multiple times to create subnets of various
sizes based on the number of hosts required in each subnet. Effective use of VLSM requires address
planning.
In this lab, use the 192.168.33.128/25 network address to develop an address scheme for the network
displayed in the topology diagram. VLSM is used to meet the IPv4 addressing requirements. After you have
designed the VLSM address scheme, you will configure the interfaces on the routers with the appropriate IP
address information. The future LANS at BR2 will need to have addresses allocated, but no interfaces will be
configured at this time.
Note: The routers used with CCNA hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.4
(universalk9 image). The switches used in the labs are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2)
(lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model
and Cisco IOS version, the commands available and the output produced might vary from what is shown in
the labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.
Note: Make sure that the routers have been erased and have no start-up configurations. If you are unsure,
contact your instructor.

Required Resources
• 2 Routers (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable)
• 2 Switches (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
• 1 PCs (Windows with terminal emulation program, such as Tera Term)
• Console cables to configure the Cisco IOS devices via the console ports
• Ethernet and serial cables as shown in the topology
© 2019 - 2023 Public Page 1 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme
Cisco and/or its affiliates. All rights reserved. Cisco
• Windows Calculator (optional)

Instructions Part 1: Examine Network Requirements

In Part 1, you will examine the network requirements to develop a VLSM address scheme for the network
displayed in the topology diagram using the 192.168.33.128/25 network address.
Note: You can use the Windows Calculator application and search the internet for an IP subnet calculator to
help with your calculations.

Step 1: Determine how many host addresses and subnets are available.
Questions:

How many host addresses are available in a /25 network?

126
Type your answers here.
What is the total number of host addresses needed in the topology diagram?
80
Type your answers here.
How many subnets are needed in the network topology? 6
Type your answers here.

Step 2: Determine the largest subnet.

Questions:

What is the subnet description (e.g. BR1 LAN or BR1-BR2 link)?

BR1 LAN
Type your answers here.
How many IP addresses are required in the largest subnet?
40
Type your answers here.
What subnet mask can support that many host addresses?
/26 or 255.255.255.192
Type your answers here.
How many total host addresses can that subnet mask support?
62
Type your answers here.
Can you subnet the 192.168.33.128/25 network address to support this subnet?
YES
Type your answers here.
What are the network addresses that would result from this subnetting?
192.168.33.128/26 and 192.168.33.192/26
Type your answers here.
Use the first network address for this subnet.

© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme

Step 3: Determine the second largest subnet.

Questions:

What is the subnet description?

BR2 LAN
Type your answers here.
How many IP addresses are required for the second largest subnet?
25
Type your answers here.
What subnet mask can support that many host addresses?
/27 or 255.255.255.224
Type your answers here.
How many total host addresses can that subnet mask support?
30
Type your answers here.
Can you subnet the remaining subnet again and still support this subnet?
YES
Type your answers here.
What are the network addresses that would result from this subnetting?
192.168.33.192/27 and 192.168.33.224/27 Type
your answers here.
Use the first network address for this subnet.

Step 4: Determine the third largest subnet.

Questions:

What is the subnet description?

BR2 IoT LAN
Type your answers here.
How many IP addresses are required for the next largest subnet?
5
What subnet mask can support that many host addresses?
/29 or 255.255.255.248 ype
your answers here.
How many total host addresses can that subnet mask support?
6
Type your answers here.
Can you subnet the remaining subnet again and still support this subnet?
YES
Type your answers here.
What are the network addresses that would result from this sub netting?
192.168.33.224/29, 192.168.33.232/29, 192.168.33.240/29, and 192.168.33.248/29
Type your answers here.
© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme
Use the first network address for this subnet.
Use the second network address for the CCTV LAN.
Use the third network address for the HVAC C2 LAN.

Step 5: Determine the fourth largest subnet.

Questions:

What is the subnet description?

BR1-BR2 Link
Type your answers here.
How many IP addresses are required for the next largest subnet? 2
Type your answers here.
What subnet mask can support that many host addresses?
/30 or 255.255.255.252
Type your answers here.
How many total host addresses can that subnet mask support? 2
Type your answers here.
Can you subnet the remaining subnet again and still support this subnet?
YES
Type your answers here.
What are the network addresses that would result from this subnetting?
192.168.33.248/30 and 192.168.33.252/30 Type
Use the first network address for this subnet.

Part 2: Design the VLSM Address Scheme

Step 1: Calculate the subnet information.
Use the information that you obtained in Part 1 to fill in the following table.

Number of Network Address First Host Broadcast

Hosts Needed /CIDR Address Address
Subnet Description

BR1 LAN 40 192.168.33.128/25 192.168.33.129 192.168.33.191

BR2 LAN 25 192.168.33.192/27 192.168.33.193 192.168.33.223

BR2 IoT LAN 5 192.168.33.224/29 192.168.33.225 192.168.33.231

Number of Network Address First Host Broadcast

Hosts Needed /CIDR Address Address
Subnet Description

BR2 CCTV LAN 4 192.168.33.232/29 192.168.33.233 192.168.33.239

BR2 HVAC C2LAN 4 192.168.33.240/29 192.168.33.241 192.168.33.247

BR1-BR2 Link 2 192.168.33.248/30 192.168.33.249 192.168.33.251

© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme

Step 2: Complete the device interface address table.

Assign the first host address in the subnet to the Ethernet interfaces. BR1 should be assigned the first host
address in the BR1-BR2 Link.

Device Interface IP Address Subnet Mask Device Interface

BR1 G0/0/0 192.168.33.249 255.255.255.252 BR1-BR2 Link

BR1 G0/0/1 192.168.33.129 255.255.255.192 40 Host LAN

BR2 G0/0/0 192.168.33.250 255.255.255.252 BR1-BR2 Link

G0/0/1 192.168.33.193 255.255.255.224 25 Host LAN

BR2

Part 3: Cable and Configure the IPv4 Network

In Part 3, you will cable the network to match the topology and configure the three routers using the VLSM
address scheme that you developed in Part 2.

Step 1: Cable the network as shown in the topology.

Step 2: Configure basic settings on each router.

Open a configuration window

a. Assign the device name to the routers.

router(config)# hostname BR1 router(config)#
hostname BR2
b. Disable DNS lookup to prevent the routers from attempting to translate incorrectly entered commands as
though they were hostnames. BR1(config)# no ip domain lookup
BR2(config)# no ip domain lookup
c. Assign class as the privileged EXEC encrypted password for both routers.
BR1(config)# enable secret class
BR2(config)# enable secret class
d. Assign cisco as the console password and enable login for the routers.
BR1(config)# line con 0
BR1(config-line)# password cisco
BR1(config)# login
BR2(config)# line con 0
BR2(config-line)# password cisco
BR2(config)# login
e. Assign cisco as the VTY password and enable login for the routers.
BR1(config)# line vty 0 4
BR1(config-line)# password cisco
BR1(config-line)# login
BR2(config)# line vty 0 4
BR2(config-line)# password cisco
BR2(config-line)# login

© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme
f. Encrypt the plaintext passwords for the routers.
BR1(config)# service password-encryption
BR2(config)# service password-encryption
g. Create a banner that will warn anyone accessing the device that unauthorized access is prohibited on
both routers.
BR1(config)# banner motd $ Unauthorized Access is Prohibited $
BR2(config)# banner motd $ Unauthorized Access is Prohibited $

Step 3: Configure the interfaces on each router.

a. Assign an IP address and subnet mask to each interface using the table that you completed in Part 2.
BR1(config)# interface g0/0/0
BR1(config-if)# ip address 192.168.33.249 255.255.255.252
BR1(config-if)# interface g0/0/1
BR1(config-if)# ip address 192.168.33.129 255.255.255.192
BR2(config)# interface g0/0/0
BR2(config-if)# ip address 192.168.33.250 255.255.255.252
BR2(config-if)# interface g0/0/1
BR2(config-if)# ip address 192.168.33.192 255.255.255.224
b. Configure an interface description for each interface.
BR1(config)# interface g0/0/0
BR1(config-if)# description BR1-BR2 Link
BR1(config-if)# interface g0/0/1
BR1(config-if)# description Connected to S1
BR2(config-if)# interface g0/0/0
BR2(config-if)# description BR1-BR2 Link
BR2(config-if)# interface g0/0/1
BR2(config-if)# description Connected to S2
c. Activate the interfaces.
BR1(config)# interface g0/0/0
BR1(config-if)# no shutdown
BR1(config-if)# interface g0/0/1
BR1(config-if)# no shutdown
BR2(config)# interface g0/0/0
BR2(config-if)# no shutdown
BR2(config-if)# interface g0/0/1
BR2(config-if)# no shutdown
Step 4: Save the configuration on all devices.
BR1# copy running-config startup-config
BR2# copy running-config startup-config

© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 7 www.netacad.com
Lab - Design and Implement a VLSM Addressing Scheme

Step 5: Test Connectivity.

a. From BR1, ping BR2’s G0/0/0 interface.
b. From BR2, ping BR1’s G0/0/0 interface.
c. Troubleshoot connectivity issues if pings were not successful.
Close a configuration window

Note: Pings to the GigabitEthernet LAN interfaces on other routers will not be successful. A routing protocol
needs to be in place for other devices to be aware of those subnets. The GigabitEthernet interfaces also need
to be in an up/up state before a routing protocol can add the subnets to the routing table. The focus of this lab
is on VLSM and configuring the interfaces.

Reflection Question
Can you think of a shortcut for calculating the network addresses of consecutive /30 subnets?
Answers may vary. A /30 network has 4 address spaces: the network address, 2 host addresses, and a
broadcast address. Another technique for obtaining the next /30 network address would be to take the
network address of the previous /30 network and add 4 to the last octet.
Type your answers here.

Router Interface Summary Table

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

Fast Ethernet 0/0 Fast Ethernet 0/1

(F0/0) (F0/1)
1800 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Gigabit Ethernet 0/0 Gigabit Ethernet 0/1

(G0/0) (G0/1)
1900 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Fast Ethernet 0/0 Fast Ethernet 0/1

(F0/0) (F0/1)
2801 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)

Fast Ethernet 0/0 Fast Ethernet 0/1

(F0/0) (F0/1)
2811 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

Gigabit Ethernet 0/0 Gigabit Ethernet 0/1

(G0/0) (G0/1)
2900 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1

(G0/0/0) (G0/0/1)
4221 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)

Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1

(G0/0/0) (G0/0/1)
4300 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
End of document

© 2019 - 2023 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 7 www.netacad.com