LM111/LM211/LM311 Voltage Comparator

August 2000

LM111/LM211/LM311
Voltage Comparator
1.0 General Description the devices are also much less prone to spurious oscilla-
tions. The LM111 has the same pin configuration as the
The LM111, LM211 and LM311 are voltage comparators that LM106 and LM710.
have input currents nearly a thousand times lower than de-
The LM211 is identical to the LM111, except that its perfor-
vices like the LM106 or LM710. They are also designed to
mance is specified over a −25˚C to +85˚C temperature range
operate over a wider range of supply voltages: from standard
instead of −55˚C to +125˚C. The LM311 has a temperature
± 15V op amp supplies down to the single 5V supply used for
range of 0˚C to +70˚C.
IC logic. Their output is compatible with RTL, DTL and TTL
as well as MOS circuits. Further, they can drive lamps or re-
lays, switching voltages up to 50V at currents as high as 50 2.0 Features
mA. n Operates from single 5V supply
Both the inputs and the outputs of the LM111, LM211 or the n Input current: 150 nA max. over temperature
LM311 can be isolated from system ground, and the output n Offset current: 20 nA max. over temperature
can drive loads referred to ground, the positive supply or the n Differential input voltage range: ± 30V
negative supply. Offset balancing and strobe capability are n Power consumption: 135 mW at ± 15V
provided and outputs can be wire OR’ed. Although slower
than the LM106 and LM710 (200 ns response time vs 40 ns)

3.0 Typical Applications (Note 3)

Offset Balancing Strobing

DS005704-36

DS005704-37

Note: Do Not Ground Strobe Pin. Output is turned off when current is
pulled from Strobe Pin.

Increasing Input Stage Current (Note 1) Detector for Magnetic Transducer

DS005704-38

Note 1: Increases typical common mode slew from 7.0V/µs to 18V/µs.

DS005704-39

© 2000 National Semiconductor Corporation DS005704 www.national.com

LM111/LM211/LM311
3.0 Typical Applications (Note 3) (Continued)

Digital Transmission Isolator Relay Driver with Strobe

DS005704-40

DS005704-41

*Absorbs inductive kickback of relay and protects IC from severe voltage

transients on V++ line.
Note: Do Not Ground Strobe Pin.

Strobing off Both Input and Output Stages (Note 2)

DS005704-42

Note: Do Not Ground Strobe Pin.

Note 2: Typical input current is 50 pA with inputs strobed off.
Note 3: Pin connections shown on schematic diagram and typical applications are for H08 metal can package.

Positive Peak Detector Zero Crossing Detector Driving MOS Logic

DS005704-24
DS005704-23

*Solid tantalum

www.national.com 2
 LM111/LM211/LM311
4.0 Absolute Maximum Ratings for Operating Temperature Range
the LM111/LM211(Note 10) LM111 −55˚C to 125˚C
LM211 −25˚C to 85˚C
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/ Lead Temperature (Soldering, 10 sec) 260˚C
Distributors for availability and specifications. Voltage at Strobe Pin V+−5V
Soldering Information
Total Supply Voltage (V84) 36V
Dual-In-Line Package
Output to Negative Supply Voltage (V74) 50V
Soldering (10 seconds) 260˚C
Ground to Negative Supply Voltage (V14) 30V
Small Outline Package
Differential Input Voltage ± 30V
Vapor Phase (60 seconds) 215˚C
Input Voltage (Note 4) ± 15V
Infrared (15 seconds) 220˚C
Output Short Circuit Duration 10 sec
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
ESD Rating (Note 11) 300V

Electrical Characteristics (Note 6)

for the LM111 and LM211
Parameter Conditions Min Typ Max Units
Input Offset Voltage (Note 7) TA =25˚C, RS≤50k 0.7 3.0 mV
Input Offset Current TA =25˚C 4.0 10 nA
Input Bias Current TA =25˚C 60 100 nA
Voltage Gain TA =25˚C 40 200 V/mV
Response Time (Note 8) TA =25˚C 200 ns
Saturation Voltage VIN≤−5 mV, IOUT =50 mA 0.75 1.5 V
TA =25˚C
Strobe ON Current (Note 9) TA =25˚C 2.0 5.0 mA
Output Leakage Current VIN≥5 mV, VOUT =35V 0.2 10 nA
TA =25˚C, ISTROBE =3 mA
Input Offset Voltage (Note 7) RS≤50 k 4.0 mV
Input Offset Current (Note 7) 20 nA
Input Bias Current 150 nA
Input Voltage Range V+ =15V, V− =−15V, Pin 7 −14.5 13.8,-14.7 13.0 V
Pull-Up May Go To 5V
Saturation Voltage V+≥4.5V, V− =0 0.23 0.4 V
VIN≤−6 mV, IOUT≤8 mA
Output Leakage Current VIN≥5 mV, VOUT =35V 0.1 0.5 µA
Positive Supply Current TA =25˚C 5.1 6.0 mA
Negative Supply Current TA =25˚C 4.1 5.0 mA
Note 4: This rating applies for ± 15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the negative
supply voltage or 30V below the positive supply, whichever is less.
Note 5: The maximum junction temperature of the LM111 is 150˚C, while that of the LM211 is 110˚C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line pack-
age is 110˚C/W, junction to ambient.
Note 6: These specifications apply for VS = ± 15V and Ground pin at ground, and −55˚C≤TA≤+125˚C, unless otherwise stated. With the LM211, however, all tempera-
ture specifications are limited to −25˚C≤TA≤+85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single 5V sup-
ply up to ± 15V supplies.
Note 7: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and RS.
Note 8: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 9: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin
to ground; it should be current driven at 3 to 5 mA.
Note 10: Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.
Note 11: Human body model, 1.5 kΩ in series with 100 pF.

3 www.national.com
LM111/LM211/LM311
5.0 Absolute Maximum Ratings for Operating Temperature Range 0˚ to 70˚C
the LM311(Note 12) Storage Temperature Range −65˚C to 150˚C
Lead Temperature (soldering, 10 sec) 260˚C
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/ Voltage at Strobe Pin V+−5V
Distributors for availability and specifications. Soldering Information
Dual-In-Line Package
Total Supply Voltage (V84) 36V
Soldering (10 seconds) 260˚C
Output to Negative Supply Voltage (V74) 40V
Small Outline Package
Ground to Negative Supply Voltage (V14) 30V
Vapor Phase (60 seconds) 215˚C
Differential Input Voltage ± 30V
Infrared (15 seconds) 220˚C
Input Voltage (Note 13) ± 15V
See AN-450 “Surface Mounting Methods and Their Effect
Power Dissipation (Note 14) 500 mW on Product Reliability” for other methods of soldering
ESD Rating (Note 19) 300V surface mount devices.
Output Short Circuit Duration 10 sec

Electrical Characteristics (Note 15)

for the LM311
Parameter Conditions Min Typ Max Units
Input Offset Voltage (Note 16) TA =25˚C, RS≤50k 2.0 7.5 mV
Input Offset Current(Note 16) TA =25˚C 6.0 50 nA
Input Bias Current TA =25˚C 100 250 nA
Voltage Gain TA =25˚C 40 200 V/mV
Response Time (Note 17) TA =25˚C 200 ns
Saturation Voltage VIN≤−10 mV, IOUT =50 mA 0.75 1.5 V
TA =25˚C
Strobe ON Current (Note 18) TA =25˚C 2.0 5.0 mA
Output Leakage Current VIN≥10 mV, VOUT =35V
TA =25˚C, ISTROBE =3 mA 0.2 50 nA
V− = Pin 1 = −5V
Input Offset Voltage (Note 16) RS≤50K 10 mV
Input Offset Current (Note 16) 70 nA
Input Bias Current 300 nA
Input Voltage Range −14.5 13.8,−14.7 13.0 V
Saturation Voltage V+≥4.5V, V− =0 0.23 0.4 V
VIN≤−10 mV, IOUT≤8 mA
Positive Supply Current TA =25˚C 5.1 7.5 mA
Negative Supply Current TA =25˚C 4.1 5.0 mA
Note 12: “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.”
Note 13: This rating applies for ± 15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the nega-
tive supply voltage or 30V below the positive supply, whichever is less.
Note 14: The maximum junction temperature of the LM311 is 110˚C. For operating at elevated temperature, devices in the H08 package must be derated based on
a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line package is 100˚C/W, junction to ambient.
Note 15: These specifications apply for VS = ± 15V and Pin 1 at ground, and 0˚C < TA < +70˚C, unless otherwise specified. The offset voltage, offset current and
bias current specifications apply for any supply voltage from a single 5V supply up to ± 15V supplies.
Note 16: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and RS.
Note 17: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 18: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin
to ground; it should be current driven at 3 to 5 mA.
Note 19: Human body model, 1.5 kΩ in series with 100 pF.

www.national.com 4
 LM111/LM211/LM311
6.0 LM111/LM211 Typical Performance Characteristics
Input Bias Current Input Bias Current Input Bias Current

DS005704-43 DS005704-44

DS005704-45

Input Bias Current Input Bias Current Input Bias Current

DS005704-47 DS005704-48
DS005704-46

Input Bias Current Input Bias Current Input Bias Current

Input Overdrives Input Overdrives

DS005704-51

DS005704-49 DS005704-50

5 www.national.com
LM111/LM211/LM311
6.0 LM111/LM211 Typical Performance Characteristics (Continued)

Response Time for Various Response Time for Various Output Limiting Characteristics
Input Overdrives Input Overdrives

DS005704-54

DS005704-52 DS005704-53

Supply Current Supply Current Leakage Currents

DS005704-55 DS005704-56 DS005704-57

7.0 LM311 Typical Performance Characteristics

Input Bias Current Input Offset Current Offset Error

DS005704-58 DS005704-59 DS005704-60

www.national.com 6
 LM111/LM211/LM311
7.0 LM311 Typical Performance Characteristics (Continued)

Input Characteristics Common Mode Limits Transfer Function

DS005704-61 DS005704-62 DS005704-63

Response Time for Various Response Time for Various Output Saturation Voltage
Input Overdrives Input Overdrives

DS005704-66

DS005704-64 DS005704-65

Response Time for Various Response Time for Various Output Limiting Characteristics
Input Overdrives Input Overdrives

DS005704-69

DS005704-67 DS005704-68

7 www.national.com
LM111/LM211/LM311
7.0 LM311 Typical Performance Characteristics (Continued)

Supply Current Supply Current Leakage Currents

DS005704-70 DS005704-71 DS005704-72

8.0 Application Hints 5. Since feedback to almost any pin of a comparator can
result in oscillation, the printed-circuit layout should be
8.1 CIRCUIT TECHNIQUES FOR AVOIDING engineered thoughtfully. Preferably there should be a
OSCILLATIONS IN COMPARATOR APPLICATIONS groundplane under the LM111 circuitry, for example, one
side of a double-layer circuit card. Ground foil (or, posi-
When a high-speed comparator such as the LM111 is used tive supply or negative supply foil) should extend be-
with fast input signals and low source impedances, the out- tween the output and the inputs, to act as a guard. The
put response will normally be fast and stable, assuming that foil connections for the inputs should be as small and
the power supplies have been bypassed (with 0.1 µF disc compact as possible, and should be essentially sur-
capacitors), and that the output signal is routed well away rounded by ground foil on all sides, to guard against ca-
from the inputs (pins 2 and 3) and also away from pins 5 and pacitive coupling from any high-level signals (such as
6. the output). If pins 5 and 6 are not used, they should be
However, when the input signal is a voltage ramp or a slow shorted together. If they are connected to a trim-pot, the
sine wave, or if the signal source impedance is high (1 kΩ to trim-pot should be located, at most, a few inches away
100 kΩ), the comparator may burst into oscillation near the from the LM111, and the 0.01 µF capacitor should be in-
crossing-point. This is due to the high gain and wide band- stalled. If this capacitor cannot be used, a shielding
width of comparators like the LM111. To avoid oscillation or printed-circuit foil may be advisable between pins 6 and
instability in such a usage, several precautions are recom- 7. The power supply bypass capacitors should be lo-
mended, as shown in Figure 1 below. cated within a couple inches of the LM111. (Some other
1. The trim pins (pins 5 and 6) act as unwanted auxiliary in- comparators require the power-supply bypass to be lo-
puts. If these pins are not connected to a trim-pot, they cated immediately adjacent to the comparator.)
should be shorted together. If they are connected to a 6. It is a standard procedure to use hysteresis (positive
trim-pot, a 0.01 µF capacitor C1 between pins 5 and 6 feedback) around a comparator, to prevent oscillation,
will minimize the susceptibility to AC coupling. A smaller and to avoid excessive noise on the output because the
capacitor is used if pin 5 is used for positive feedback as comparator is a good amplifier for its own noise. In the
in Figure 1. circuit of Figure 2, the feedback from the output to the
2. Certain sources will produce a cleaner comparator out- positive input will cause about 3 mV of hysteresis. How-
put waveform if a 100 pF to 1000 pF capacitor C2 is con- ever, if RS is larger than 100Ω, such as 50 kΩ, it would
nected directly across the input pins. not be reasonable to simply increase the value of the
3. When the signal source is applied through a resistive positive feedback resistor above 510 kΩ. The circuit of
network, RS, it is usually advantageous to choose an RS' Figure 3 could be used, but it is rather awkward. See the
of substantially the same value, both for DC and for dy- notes in paragraph 7 below.
namic (AC) considerations. Carbon, tin-oxide, and 7. When both inputs of the LM111 are connected to active
metal-film resistors have all been used successfully in signals, or if a high-impedance signal is driving the posi-
comparator input circuitry. Inductive wirewound resistors tive input of the LM111 so that positive feedback would
are not suitable. be disruptive, the circuit of Figure 1 is ideal. The positive
4. When comparator circuits use input resistors (eg. sum- feedback is to pin 5 (one of the offset adjustment pins).
ming resistors), their value and placement are particu- It is sufficient to cause 1 to 2 mV hysteresis and sharp
larly important. In all cases the body of the resistor transitions with input triangle waves from a few Hz to
should be close to the device or socket. In other words hundreds of kHz. The positive-feedback signal across
there should be very little lead length or printed-circuit the 82Ω resistor swings 240 mV below the positive sup-
foil run between comparator and resistor to radiate or ply. This signal is centered around the nominal voltage at
pick up signals. The same applies to capacitors, pots, pin 5, so this feedback does not add to the VOS of the
etc. For example, if RS =10 kΩ, as little as 5 inches of comparator. As much as 8 mV of VOS can be trimmed
lead between the resistors and the input pins can result out, using the 5 kΩ pot and 3 kΩ resistor as shown.
in oscillations that are very hard to damp. Twisting these
input leads tightly is the only (second best) alternative to
placing resistors close to the comparator.

www.national.com 8
 LM111/LM211/LM311
8.0 Application Hints (Continued) are applicable to all high-speed comparators in general,
(with the exception that not all comparators have trim
8. These application notes apply specifically to the LM111, pins).
LM211, LM311, and LF111 families of comparators, and

DS005704-29

Pin connections shown are for LM111H in the H08 hermetic package

FIGURE 1. Improved Positive Feedback

DS005704-30

Pin connections shown are for LM111H in the H08 hermetic package

FIGURE 2. Conventional Positive Feedback

9 www.national.com
LM111/LM211/LM311
8.0 Application Hints (Continued)

DS005704-31

FIGURE 3. Positive Feedback with High Source Resistance

9.0 Typical Applications (Pin numbers refer to H08 package)

Zero Crossing Detector Driving MOS Switch 100 kHz Free Running Multivibrator

DS005704-13

DS005704-14

*TTL or DTL fanout of two

www.national.com 10
 LM111/LM211/LM311
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)

10 Hz to 10 kHz Voltage Controlled Oscillator

DS005704-15

*Adjust for symmetrical square wave time when VIN = 5 mV

†Minimum capacitance 20 pF Maximum frequency 50 kHz

Driving Ground-Referred Load Using Clamp Diodes to Improve Response

DS005704-17

DS005704-16

*Input polarity is reversed when using pin 1 as output.

TTL Interface with High Level Logic

DS005704-18

*Values shown are for a 0 to 30V logic swing and a 15V threshold.
†May be added to control speed and reduce susceptibility to noise spikes.

11 www.national.com
LM111/LM211/LM311
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)

Crystal Oscillator Comparator and Solenoid Driver

DS005704-20

DS005704-19

Precision Squarer

DS005704-21

*Solid tantalum
†Adjust to set clamp level

www.national.com 12
 LM111/LM211/LM311
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)

Low Voltage Adjustable Reference Supply

DS005704-22

*Solid tantalum

Positive Peak Detector Zero Crossing Detector Driving MOS Logic

DS005704-24
DS005704-23

*Solid tantalum

Negative Peak Detector

DS005704-25

*Solid tantalum

13 www.national.com
LM111/LM211/LM311
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)

Precision Photodiode Comparator

DS005704-26

*R2 sets the comparison level. At comparison, the photodiode has less than 5 mV across it, decreasing leakages by an order of magnitude.

Switching Power Amplifier

DS005704-27

www.national.com 14
 LM111/LM211/LM311
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)

Switching Power Amplifier

DS005704-28

15 www.national.com
LM111/LM211/LM311
10.0 Schematic Diagram (Note 20)

DS005704-5

Note 20: Pin connections shown on schematic diagram are for H08 package.

www.national.com 16
 LM111/LM211/LM311
11.0 Connection Diagrams
Metal Can Package

DS005704-6

Note: Pin 4 connected to case

Top View
Order Number LM111H, LM111H/883(Note 21) , LM211H or LM311H
See NS Package Number H08C

Dual-In-Line Package
Dual-In-Line Package

DS005704-34

Top View
DS005704-35
Order Number LM111J-8, LM111J-8/883(Note 21),
LM311M, LM311MX or LM311N Top View
See NS Package Number J08A, M08A or N08E Order Number LM111J/883(Note 21)
See NS Package Number J14A or N14A

DS005704-33

Order Number LM111W/883(Note 21), LM111WG/883

See NS Package Number W10A, WG10A

Note 21: Also available per JM38510/10304

17 www.national.com
LM111/LM211/LM311
12.0 Physical Dimensions inches (millimeters) unless otherwise noted

Metal Can Package (H)

Order Number LM111H, LM111H/883, LM211H or LM311H
NS Package Number H08C

Cavity Dual-In-Line Package (J)

Order Number LM111J-8, LM111J-8/883
NS Package Number J08A

www.national.com 18
 LM111/LM211/LM311
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Dual-In-Line Package (J)

Order Number LM111J/883
NS Package Number J14A

Dual-In-Line Package (M)

Order Number LM311M, LM311MX
NS Package Number M08A

19 www.national.com
LM111/LM211/LM311
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Dual-In-Line Package (N)

Order Number LM311N
NS Package Number N08E

Order Number LM111W/883, LM111WG/883

NS Package Number W10A, WG10A

www.national.com 20
 LM111/LM211/LM311 Voltage Comparator
Notes

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Corporation Europe Asia Pacific Customer Japan Ltd.
Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560
Tel: 1-800-272-9959 Email: [email protected] Tel: 65-2544466 Fax: 81-3-5639-7507
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466
Email: [email protected] English Tel: +44 (0) 870 24 0 2171 Email: [email protected]
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.