Takeuchi Tb108 Operators Manual

Full download: http://manualplace.com/download/takeuchi-tb108-operators-manual/

TB108
TB108

Compact Excavator
OPERATOR’S MANUAL

Serial No.108202134~
Book No. AB5E014

OPERA TOR’S MANUAL Original instructions

WARNING
Read and understand these instructions.
Failure to do so can cause injury or death.

E is the cut pages sample. Download all 172 page(s) at: ManualPlace.com
This
 SAFETY ALERT SYMBOL
This symbol means Attention! Be Alert! Your Safety Is Involved.
The message that follows the symbol contains important information
about safety.
Read and understand the message to avoid personal injury or death.

■ It is the owner or employer’s responsibility to fully instruct each operator in the

proper and safe operation of all equipment. All persons using this machine should
thoroughly familiarize themselves with the following sections.

■ All operators must be instructed on the proper functions of the excavator before
running the machine.

■ Learn and practice correct use of the machine controls in a safe, clear area before
operating this machine on a job site.

CAUTION

Improper operation, inspection and maintenance of this

machine can cause injury or death.
Read and understand this manual before performing any
operation, inspection or maintenance on this machine.

■ Always store this manual near at hand preferably on the machine itself. If it should be lost
or damaged, immediately order a new one from your Takeuchi dealer.
When transferring ownership of this machine, be sure to provide this manual to the next
owner.

■ Takeuchi supplies machines complying to the local regulations and standards of the country
of export. If your machine has been purchased in another country or from a person or
company of another country, it may not have the safety devices or safety standards required
for use in your country. Should you have any question about whether your machine complies
with the regulations and standards of your country, contact a Takeuchi dealer.

■ Please note that the contents and diagrams included in this manual may not match your
machine exactly.
It is your responsibility to observe all pertinent laws and regulations and to follow the
manufacturer’s instructions on machine operation, inspection and maintenance.

Virtually all accidents occur as the result of a failure to observe basic safety rules and
precautions. An accident can often be avoided by recognizing potentially hazardous situations
beforehand. Read and understand all of the safety messages which explain how to prevent
these accidents from occurring. Do not operate the machine until you are sure that you have
gained a proper understanding of its operation, inspection and maintenance.

■ SlGNAL WORDS
Safety messages appearing in this manual and on machine decals are identified by the
words “DANGER”, “WARNING” and “CAUTION”. These signal words mean the following:

DANGER WARNING CAUTION

The word “DANGER” The word “WARNING” The word “CAUTlON”
indicates an imminently indicates a potentially indicates a potentially
hazardous situation hazardous situation hazardous situation
which, if not avoided, which, if not avoided, which, if not avoided,
can result in serious could result in serious may result in minor or
injury or death. injury or death. moderate injury.

IMPORTANT: The word “IMPORTANT” is used to alert against operators and

maintenance personnel about situations which can result in possible damage to the
machine and its components.

It is impossible to foresee every possible circumstance that might involve a potential hazard.
The warnings in this manual or on the machine can not cover all possible contingencies. You
must exercise all due care and follow normal safety procedures when operating the machine
so as to ensure that no damage occurs to the machine, its operators or other persons.

■ EXPLANATION OF GRAPHICAL SYMBOLS

Following is an explanation of symbols used in this manual.
/ X ......... prohibition

........... Lock

......... Unlock

1
INTRODUCTION

Foreword
This manual describes operation, inspection
and maintenance of the machine, as well as
safety instructions to be heeded during these
operations.
If you have any questions about the machine,
please contact a Takeuchi sales or service
outlet.

■ Manual storage ■ Serial numbers

A compartment for storing this manual is Check the serial numbers of the machine and
provided at the position shown on the the engine and write them in the spaces
diagram below. provided below.
After using the manual, place it in the plastic
pouch and store it back in the manual storage Machine number :
compartment.

B5A002

B5A001

Engine number :

2
MACHINE DESCRIPTlON

■ Front, rear, Ieft and right

This manual refers the front, rear, left and
right of the machine as seen when sitting in
the operator’s seat with the dozer blade
visible to the front.

■ Designated operations
Use this machine primarily for the following
operations:
¡Excavating
¡Digging ditches
¡Digging side ditches
¡Leveling
¡Loading

■ Features
¡Short pitch rubber crawler
¡Low engine noise and exhaust emissions
¡Fast working speed and low-shock working equipment
¡Excellent stability thanks to a low center of gravity

■ Break-in period
When is new, heed the instructions below when operating the machine for the first 100 hours
(as indicated on the hour meter).
Using a new machine roughly without breaking it in will lead to quicker deterioration of machine
performance and may shorten the machine’s service life.
¡Warm up the engine and hydraulic oil sufficiently.
¡Avoid heavy loads and rapid operations. Operate with a load of about 80% the maximum
load.
¡Do not start up, accelerate, change directions, or stop abruptly unless necessary.

3
4
CONTENTS
Introduction..........................................2
Machine Description ..........................3

Safety ....................................................7

Controls ............................................. 35

Operation........................................... 51

Transport ........................................... 81

Maintenance ..................................... 85

Troubleshooting.............................. 125

Specifications ................................. 135

Options ............................................ 149

Index................................................. 163

5
6
 SAFETY
General precautions .................................... 8
Preparing precautions ............................... 12
Starting precautions .................................. 14
Operating precautions ............................... 16
Stopping precautions ................................ 23
Transporting precautions .......................... 24
Maintenance precautions .......................... 25
Safety signs (decals) ................................. 32

7
Takeuchi Tb108 Operators Manual
SAFETY
Full download: http://manualplace.com/download/takeuchi-tb108-operators-manual/
General Precautions

Observe all safety rules · If operated at an ambient temperature

of lower than –15°C (+5°F), the parts
� Operation, inspection and maintenance made of rubber such as gaskets may
of this machine must be performed only get hardened to cause an early wear or
by a trained and qualified person. damage to the machine.
� All rules, regulations, precautions and · If the machine is to be used outside the
safety procedures must be understood ambient temperature range described
and followed when performing operation, above, consult your sales or a service
inspection and maintenance of this dealer.
machine.
� Do not perform any operation, inspection
and maintenance of this machine when
under the adverse influence of alcohol,
drugs, medication, fatigue, or insufficient Wear appropriate clothing and
sleep. personal protective equipment

When a problem is found on the

machine
When a problem is found on the machine
If any problem (noise, vibration, smell,
disorder of instrument, smoke, oil leak, wrong
indication of alarm or unusual indication
in the instrument cluster, etc.) is detected
� Do not wear loose clothing or any
during the operation or inspection and
accessory that can catch on controls or in
maintenance of the machine, immediately
moving parts.
inform your sales or service dealer and take
� Do not wear oily or fuel stained clothing
proper actions. Do not operate the machine
that can catch fire.
until the trouble is cleared.
� Wear a hard hat, safety shoes, safety
glasses, filter mask, heavy gloves, ear
protection and other protective equipment
Operating temperature range
as required by job conditions. Wear
required appropriate equipment such as
To maintain the performance of machine and safety glasses and filter mask when using
to prevent it from early wear, observe the grinders, hammers or compressed air, as
following operating conditions. metal fragments or other objects can fly
� Do not operate the machine if the ambient and cause serious injury.
temperature is higher than +45°C (+113°F) � Use hearing protection when operating
or lower than –15°C (+5°F). the machine. Loud prolonged noise can
· If operated at an ambient temperature cause hearing impairments, even the total
of higher than +45°C (+113°F), the loss of hearing.
engine may overheat and cause the
engine oil to degrade.

8
This is the cut pages sample. Download all 172 page(s) at: ManualPlace.com