PowerSeries Pro V1.1 Reference Manual 29010134R005 en

intrusion
PowerSeries Pro Alarm Controller

Reference Manual
Models:
HS3032, HS3128,
and HS3248
WARNING: This manual contains information on limitations regarding product use and function and information on the lim-
itations as to liability of the manufacturer. Carefully read the entire manual.
Safety instructions for service personnel
Warning: When using equipment connected to the telephone network, always follow the basic safety instructions provided
with this product. Save these instructions for future reference. Inform the end-user of the safety precautions that must be
observed when operating this equipment.
Before installing the equipment
Ensure your package includes the following items:
l Installation and User manuals, including the safety instructions.
l Read and save these instructions.
l Follow all warnings and instructions specified within this document and/or on the equipment.
l HS3032/HS3128/HS3248 alarm controller
l Power Supply, direct plug-in
Selecting a suitable location for the alarm controller
Use the following list as a guide to find a suitable location to install this equipment:
l Locate near a telephone socket and power outlet.
l Select a location free from vibration and shock.
l Place alarm controller on a flat, stable surface and follow the installation instructions.
l Do not locate this product where people may walk on the secondary circuit cable(s).
l Do not connect alarm controller to electrical the same circuit as large appliances.
l Do not select a location that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chem-
icals or dust.
l Do not install this equipment near water. (e.g., bath tub, kitchen/laundry sink, wet basement, near a swimming pool).
l Do not install this equipment and accessories in areas where risk of explosion exists.
l Do not connect this equipment to electrical outlets controlled by wall switches or automatic timers.
l Avoid interference sources.
l Avoid installing equipment near heaters, air conditioners, ventilators, and refrigerators.
l Avoid locating equipment close to or on top of large metal objects (e.g., wall studs).
l See "Locating detectors and escape plan" on page 285 for information on locating smoke and CO detectors.
Safety precautions required during installation
l Never install this equipment and/or telephone wiring during a lightning storm.
l Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the net-
work interface.
l Position cables so that accidents can not occur. Connected cables must not be subject to excessive mechanical
strain.
l Use only the power supply provided with this equipment. Use of unauthorized power supplies may cause damage.
l For direct plug-in versions, use the power supply module supplied with the device.
Warning: This equipment has no mains on/off switch. The plug of the direct plug in versions of this equipment is intended to
serve as the disconnecting device. It is imperative that access to the mains plug and associated mains socket/outlet is never
obstructed. For permanently connected versions of this equipment the fuse in the connector block is the disconnect device. If
the neutral wire cannot be identified, then this equipment must be connected to a mains source that comes from a dis-
connect device that simultaneously disconnects both poles (Line and Neutral).
Important note for international market (EU, Australia, New Zealand)
This equipment is stationary-fixed and must be installed by Skilled Persons only. Skilled Person is defined as a person with
relevant education or experience to enable him or her to identify hazards and to take appropriate actions to reduce the risks
of injury to themselves and others.
l It must be installed and used within an environment that provides the pollution degree max 2, over voltages category
II, in non-hazardous, indoor locations only.
l Use authorized accessories only with this equipment. Do not place any object on the top of the cabinet of this equip-
ment! Do not spill any liquids on the cabinet.
l Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of electric shock.
l Ensure that cables are positioned so that accidents cannot occur. Connected cables must not be subject to excessive
mechanical strain. Do not use the Alarm system to report a gas leak if the system is near a leak.
l These safety instructions should not prevent you from contacting the distributor and/or the manufacturer to obtain any
further clarification and/or answers to your concerns.
-2-
Contents
Section 1: Introduction 5
1.1 About the system 5
Section 2: Installation 11
2.1 Overview of installation process 11
2.2 Alarm controller installation 11
2.3 General wiring instructions 17
2.4 Installing modules 30
Section 3: Configuration 44
3.1 Basic configuration steps 44
3.2 Using the keypad 44
3.3 Enrollment 45
3.4 Working with partitions 47
3.5 Trouble indicators 48
3.6 Keypad partition setup 48
3.7 Alternate communicator setup 50
3.8 Local firmware upgrade 51
3.9 Testing the system 51
Section 4: System operation 52
4.1 Arming and disarming 52
4.2 Partition vs. global keypad 52
4.3 Labels 53
4.4 Annunciation 54
4.5 Keypad function keys 55
4.6 Language selection 57
4.7 [*] Commands 58
4.8 Visual verification 71
Section 5: Programming 72
5.1 How to program 72
5.2 Programming methods 72
5.3 Programming descriptions 75
Section 6: Programming Worksheets 154
6.1 Label Programming 154
6.2 Zone Setup 160
6.3 End Of Line Resistance 162
6.4 System Times 162
6.5 Access Codes 164
6.6 PGM Programming 164
6.7 System Lockout 187
6.8 System Options 188
6.9 Auto-Arm_Disarm 192
6.10 Partition and Zone Assignment 196
6.11 Communications 199
6.12 Call Directions 207
-3-
6.13 DLS Programming 210
6.14 Virtual Inputs 211
6.15 Schedule Programming 212
6.16 Audio Module Programming 216
6.17 Wireless Programming 224
6.18 Alternate Communicator 225
6.19 Keypad Programming 232
6.20 Template Programming 234
6.21 System Information 234
6.22 Module Programming 235
6.23 Wireless Placement Testing 236
6.24 Battery Settings 237
6.25 Restoring Factory Defaults 238
Section 7: Troubleshooting 239
7.1 Testing 239
7.2 Troubleshooting 239
Appendix 1: Reporting codes 250
Appendix 2: Word library 257
Appendix 3: Template programming tables 258
Appendix 4: ASCII characters 264
Appendix 5: Regulatory approvals 265
5.1 FCC COMPLIANCE STATEMENT 265
5.2 Innovation, Scientific and Economic Development Canada (ISED) Statement 266
5.3 UL/ULC Installations 266
5.4 Aux loading and battery selection 270
5.5 SIA False Alarm Reduction Installations: Quick Reference 270
5.6 EUROPEAN EN50131 COMPLIANCE STATEMENT 272
5.7 UK Compliance Statement 274
Appendix 6: Wiring diagrams 276
6.1 HS3032, HS3128, and HS3248 UL/ULC wiring diagram (North America only) 276
6.2 HS3032 and HS3248 wiring diagram (EN50131 only) HSC3020C enclosure 277
6.3 HS3032 and HS3248 wiring diagram (EN50131 only) HSC3020CP enclosure 278
6.4 Zone wiring 278
6.5 Bell wiring 279
6.6 Aux power wiring 280
6.7 Corbus wiring 280
6.8 PGM wiring 281
6.9 Telephone line wiring 282
6.10 Earth ground wiring 282
Appendix 7: Specifications 283
7.1 Locating detectors and escape plan 285
8.0 Limited warranty 288
8.0 SOFTWARE PRODUCT LICENSE 291
-4-
Section 1: Introduction
1.1 About the system
The PowerSeries Pro alarm panel is a feature-rich, scalable alarm system designed for commercial use. The alarm panel
supports both hardwired and wireless devices. This section lists the features of the alarm panel, available models, and com-
patible devices.
The following symbols are used to indicate features or methods of operation that are only available in a particular market. No
symbol indicates the feature or operation is available for all markets unless noted specifically otherwise.
CP-01
- North America
EN
- Europe
NFA2P
- France
UK
- United Kingdom
Features
The following features are available on the PowerSeries Pro alarm controller.
Zones, wireless keypads, wireless keys, panic pendants, and proximity tags
The system supports the following devices:
l 32 or 128 wireless zones or 32, 128, or 248 wired zones. This includes the 8 wired zones available on the con-
trollers.
l 41 zone types and 15 programmable zone attributes.
l 8 or 16 separate keypads supported.
l 32 separate wireless keys supported.
l 72 or 1000 separate proximity tags supported.
Access codes
l Up to 1002 access codes: 1000 (level 2-EN) including one system master code (level 2-EN). In addition, one installer
code (level 3-EN), and one maintenance code are available.
Note: EN50131-1 compliant systems using more than 100 access codes shall set the access code to 8 digits (section
[041], option 02).
l Programmable attributes for each user code (see "Access code attributes" on page 65)
Programmable outputs (PGMs)
l Up to 4 programmable outputs (PGM) on the alarm controller with 50 available options
l 44, 166, or 180 maximum programmable outputs for HS3032, HS3128, HS3248.
System supervision features
The PowerSeries Pro continuously monitors a number of possible trouble conditions and provides audible and visual indic-
ation at the keypad. Trouble conditions include:
l AC power failure
l Zone trouble
l Fire trouble
l Telephone line trouble
l Communicator trouble
l Low battery condition
l RF jam
l AUX power supply fault
l Failure to communicate
l Module fault (supervisory or tamper)
-5-
l Bell trouble
l Corbus troubles
l Power unit trouble
Available models
The following alarm controller models are available:
l HS3032
l HS3128
l HS3248
Model comparison
The table below lists the features of each alarm system model.
Table 1-1 Model comparison
Features HS3032 HS3128 HS3248
On board
Zones 8 8 8
PGMs 4 4 4
2-way audio interface 1 1 1
Cellular plug-in interface 1 1 1
On-board ethernet connection 1 1 1
PC-link interface 1 1 1
USB connectors 2 2 2
PC- Link 1 1 1
Expansion
Zones 32 128 248
Low current PGMs 32 128 128
High current PGMs 4 16 16
Relay output PGMs 4 32 32
Partitions 4 8 8
Keypads 8 16 16
Users 72 1000 1000
Standard event buffer 500 1000 1000
Priority event buffer 2000 2000 2000
Alarm buffer 100 100 100
Arming buffer 100 100 100
Wireless device expansion
Wireless zones 32 128 128
Panic pendant zones 32 32 32
Wireless keys 32 32 32
Sirens 8 16 16
Repeaters * 8 8 8
Module expansion
PowerG Transceiver - HSM2HOST 1 1 1
8 Zone Expander - HSM2108 ** 3 15 30
-6-
Features HS3032 HS3128 HS3248

PGM Expander - HSM2208 4 16 16
1A Power Supply - HSM2300 3 4 4
Power supply with 4 outputs - HSM2204 1 4 4
3A Power supply - HSM3350 3 4 4
2-way audio module - HSM2955 1 1 1
Corbus repeater - HSM3204CX * 1 8 8
8-zone expander - HSM3408 ** 3 15 30
Plug In cellular module - XX9080 1 1 1
LCD Keypad with Prox - HS2LCDPRO 8 16 16
LCD Keypad with Prox and Host - HS2LCDRFPROx 1 1 1
Touchscreen with Prox - HS2TCHPRO(BLK) 8 16 16
Wire-free Keypad with Prox - HS2LCDWFPROx 8 16 16
Wire-free Keypad Prox and Voice - HS2LCDWFVPROx 8 16 16
*For UL installations, 2 repeaters must be installed for proper signal routing.

**HSM3408/HSM2108 can be enrolled on the system at the same time but each take up 1 zone expander module slot. The
max combined zone expander modules slots are 3 on the HS3032, 15 on the HS3128, and 30 on the HS3248.
-7-
Compatible devices
The following wireless devices and modules are compatible with this alarm controller.
Note: In the table below and throughout this document, x in the model number represents the operating frequency of the
device as follows: 9 (912-919 MHz), 8 (868MHz), 4 (433MHz).
Note: Only models operating in the band 912-919 MHz are UL/ULC listed where indicated. Only UL approved devices are to
be used with UL/ULC listed systems.
Table 1-2 Compatible devices

Modules
Wireless keypads HS2LCDWFPROx UL
HS2LCDWFVPROx UL
Hardwired keypads with PG host HS2LCDRFPROx UL
Hardwired keypads HS2LCDPRO UL
Touchscreen keypad HS2TCHPRO(BLK) UL
Note: For ULC-s559 Listed applications the HS2TCHPRO(BLK) touchscreen keypad is for
supplementary use only.
2-way wireless transceiver HSM2HOSTxUL
8-zone expander HSM2108UL
8 low current output expander: HSM2208UL
8-zone expander HSM3408UL
1 A Power supply HSM2300UL
3 A Power supply HSM3350UL
4 High current output expander HSM2204UL
Audio verification module HSM2955(R) UL
Power supply/relay output/Corbus repeater module HSM3204CXUL
USB to WiFi adapter HSM3WIFI
Alternate communicator LE9080UL
3G9080-EU
TL880LT NUL
TL880LTVZ N
TL880LEAT N
TL8803G NUL
TL880LE N
-8-
Hardwired devices
2-wire smoke detector FSA-210xUL
FSA-210xT UL
x = A, B, or C FSA-210xSUL
A = ULC listed models FSA-210xST UL
B = UL listed models FSA-210xLST UL
C = European and Australian models FSA-210xRUL
FSA-210xRT UL
L = Remote LED output FSA-210xRSUL
R = Auxiliary form C relay FSA-210xRST UL
S = Sounder FSA-210xLRST UL
T = Temperature sensor
4-wire smoke detector FSA-410xUL
FSA-410xT UL
x = A, B, or C FSA-410xSUL
A = ULC listed models FSA-410xST UL
B = UL listed models FSA-410xLST UL
C = European and Australian models FSA-410xRUL
FSA-410xRT UL
L = Remote LED output FSA-410xRSUL
R = Auxiliary form C relay FSA-410xRST UL
S = Sounder FSA-410xLRST UL
T = Temperature sensor
CO detector CO-12/24UL
12-24SIRUL
FW-CO12UL
FW-CO1224UL
CO1224UL
PowerG wireless devices
PowerG wireless short range ceiling mount detector with temperature monitoring PGx862 UL
PowerG wireless long range ceiling mount detector with temperature monitoring PGx872 UL
PowerG wireless outdoor curtain PIR PGx902 UL
PowerG wireless PIR motion detector with optional animal resistance PGx904(P) UL
PowerG wireless PIR motion detector with temperature monitoring PGx914(P) UL
PowerG wireless curtain PIR motion detector PGx924 UL
PowerG wireless PIR motion detector with camera PGx934(P) UL
PowerG wireless outdoor PIR motion detector with camera and with anti-masking PGx944
PowerG wireless mirror optic PIR motion detector PGx974(P) UL
PowerG wireless dual technology (PIR and MW) with anti-masking PGx984(P) UL
PowerG wireless outdoor PIR motion detector with anti-masking PGx994 UL
PowerG wireless recessed door/window contact PGx307
PowerG wireless outdoor contact with axillary input, temperature monitoring, and anti-masking PGx312 UL
PowerG wireless door/window contact with auxiliary input PGx945 UL
PowerG wireless vanishing door/window contact PGx975 UL / PGx303 UL
-9-
PowerG wireless glassbreak detector PGx912/PGx922 UL

PowerG wireless shock detector with auxiliary input PGx935 UL
PowerG wireless flood detector PGx985 UL
PowerG wireless temperature detector PGx905 UL
PowerG wireless temperature probe extender (requires PGx905) PGTEMP-PROBE
PowerG wireless CO detector (US only) PGx913 UL
PowerG wireless CO detector with temperature monitoring PGx933 UL
PowerG wireless smoke and heat detector PGx916 UL
PowerG wireless smoke and heat detector with temperature monitoring PGx936 UL
PowerG wireless smoke detector PGx926 UL
PowerG wireless indoor siren PGx901UL
PowerG wireless outdoor siren PGx911UL
PowerG wireless repeater PGx920UL
PowerG wireless 1-button security panic keyfob PGx938UL
PowerG wireless 2-button security panic keyfob PGx949UL
PowerG wireless 4-button security panic keyfob PGx929 UL / PGx939 UL
Central station receivers
SG-System I, II, III, IV, 5
Enclosures
The PowerSeries Pro main board can be installed in the metal enclosures listed below: Tamper protection switches can be installed on all
enclosures, including door opening protection and/or removal from the mounting position. Doors can be secured using screws or keylock.
• Model HSC3010C (hinged door) made of 18 Ga steel, painted white, dimensions 372 mm x 412 mm x 114 mm, weight: 9.75 lb or 4.2 Kg
• Model HSC3010CR (hinged door) made of 18 Ga steel, painted red, dimensions 372 mm x 412 mm x 114 mm, weight: 10.0 lb or 4.5 Kg
• Model HSC3030CAR (hinged door) made of 18 Ga steel (base) and 16Ga (door), painted white, dimensions 375 mm x 412 mm x 114 mm,
weight: 11.45 lb or 5.2 Kg
• Model HSC3020C(removable door) made of 18 Ga steel, painted white, dimensions 459 mm x 414 mm x 103 mm, weight: 4.3 Kg (no batteries)
/12 Kg (17Ah)
• Model HSC3020CP (removable door) made of PC-ABS, color white, dimensions 368 mm x 489 mm x 108 mm, weight: 2.3 Kg (no batteries)/7.7
Kg (17Ah)
For EN50131-1 Grade 2 or Grade 3 compliant installations, all holes on the side of the cabinets shall be covered (plugged) if no accessories are
installed in the cabinet that will use these mounting holes
The equipment enclosure shall be secured to the building structure before operation. Use four screws (appropriate for the wall material on which
it is attached) inserted through the four mounting holes provided in the back of the enclosure base.
- 10 -
Section 2: Installation
2.1 Overview of installation process
The steps below are provided to assist with the installation of the alarm system. Read over this section to get an overall
understanding of the order of installation. Working from this plan can help reduce problems and reduce the overall time
required for installation.
Step 1 – create a layout
Draw a rough sketch of the site and include all alarm detection devices, zone expanders, keypads and other required mod-
ules.
Step 2 – mount the panel
Decide on a location for the alarm panel and secure it to the wall using suitable mounting hardware. see "Mounting the
enclosure" on page 12
Step 3 – wire the alarm controller
Wire each of the modules to the alarm controller following the guidelines provided in "Corbus wiring" on page 280
Step 4 – wire zones
Complete all zone wiring. Follow the guidelines provided in "Zone wiring" on page 35 to connect zones using normally
closed loops, single EOL resistor, double EOL resistors, triple EOL resistors, fire zones, and keyswitch arming zones.
Step 5 – complete wiring
Complete all other wiring including bells or sirens, telephone line connections, ground connections, Ethernet connection or
any other wiring necessary. Follow the guidelines provided in "Terminal descriptions" on page 27
Step 6 – power up the control panel
Once all zone and alarm controller wiring is complete, connect the battery before applying AC, and power up the system.
The alarm controller will not power up if only the battery is connected.
Step 7 – enroll keypads and modules
All keypads must be enrolled in order to operate on the system. To enroll the first keypad, see "Enrolling the first keypad " on
page 46. To enroll optional keypads, enter installer's programming section [902][000]. For more information, see "Module
Programming" on page 149.
Step 8 – confirm module supervision
By default, all modules are supervised upon installation. Supervision is enabled at all times. To confirm that each module is
properly supervised, see "[903] Confirm Module" on page 150.
Step 9 – enroll wireless devices
Wireless devices are enrolled via the wireless transceiver module (HSM2HOSTx) or RF keypad and Installer programming
section [804]. See "Wireless Programming" on page 132 to enroll wireless devices.
Step 10 – program the system
Section 5 "Programming" on page 72 provides a complete description of how to program the alarm controller. It contains
complete descriptions of the various programmable features and options. Fill out the programming worksheets starting at
"Programming Worksheets" on page 154 completely before attempting to program the system.
Step 11 – test the system
Test the panel completely to ensure that all features and functions operate as programmed.
2.2 Alarm controller installation

Begin the installation by mounting the alarm controller in the metal enclosure using the stand-offs provided. Optional mod-
ules, such as the HSM3408, can also be mounted in the enclosure.
Install hardware in the sequence indicated on the following pages.
- 11 -
Mounting the enclosure

This section provides basic instructions for wall-mounting the available PowerSeries Pro enclosures. Mount in a dry location,
near an unswitched AC power source and Ethernet and phone connections. If mounting on drywall, ensure all four screw
holes align with wall studs.
Complete all wiring before applying AC or connecting the battery.
Note: The weight of the enclosure and contents cannot be supported by drywall only. Use mounting hardware sufficient to
support up to three times the panel weight, including equipment, cables, conduit and hardware (approximately 210 lbs/ 95
kg). Select hardware suitable for the mounting surface.
Recommended minimum screw size: M4 (#8) x 4, 25.4 mm (1 inch) long, pan head.
To mount the enclosure, complete the following steps:
1. Position the enclosure in the mounting location and mark the two top screw holes and the tamper bracket hole.
2. Remove the enclosure, then install the two top screws part way and an anchor for the tamper bracket, if necessary. Do
not mount the tamper bracket directly into drywall.
3. Hang the enclosure on the installed screws then mark the two bottom mounting holes.
4. Remove the enclosure from the wall and install the components in the following order:
l Plastic standoffs for alarm controller and optional modules
l Tamper switch and bracket
l Power supply, including GND connection for HSC3010C, HSC3010CR, and HSC3030CAR enclosures (see dia-
gram). Note that the ground nut mounts from the back of the cabinet.
5. Hang the enclosure on the top two screws again then fasten the tamper bracket to the wall.
6. Install the two bottom screws. Ensure that all four screws are securely tightened.
7. Install the alarm controller. For models HSC3010C, HSC3010CR, HSC3030CAR and HSC3020C enclosures, use the
supplied metal standoff and screw in bottom-right mounting hole as indicated in figure 2-1.
8. Install optional modules and wire according to the instructions provided with the module.
9. Wire the tamper switch into any available zone. Configure the tamper for normally closed (NC) supervision. Zone must
be programmed for 24-hour latching or non-latching tamper.
10. Install the batteries only after the enclosure has been permanently secured to the wall.
Note: For NFA2P certified systems, when using the cellular communicator 3G9080-EU, install also the tamper bracket part
number 09000996. See Installing the tamper bracket
Figure 2-1 Installing the tamper bracket
The following diagram indicates the mounting location of the alarm controller PCB, power supply module and tamper
bracket inside the enclosure.
Wall mounting HSC3010C/ HSC3010CR/ HSC3030CAR enclosures
bracket inside HSC3010C/ HSC3010CR/ HSC3030CAR enclosures.
- 12 -
Figure 2-2 HSC3010C, HSC3010CR, HSC3030CAR enclosures
2.57cm
[1.01in]
2.97cm 30.93cm
[1.17in] [12.28in]
16.69cm
[6.57in]
35.50cm
[13.98in]
31.27cm
[12.31in]
A Use metal standoff and screw in the position indicated. IMPORTANT! Ensure screw
and standoff are tightly secured to establish Earth ground connection for the PCB.
B Tamper mounting location
Wall mounting the HSC3020C enclosure

bracket inside the HSC3020C enclosure.
Figure 2-3 HSC3020C enclosure
A
2.69cm 40.64cm [16in]
[1.060]
2.79cm
[1.10in]
18.44cm
[7.26in]
0.97cm
[0.38in]
35.38cm
[13.93in]
A Tamper mounting location.

Note: When power adapter model HS65WPSNA is not mounted inside the enclosure model HSC3010C or HSC3020C, it
must be attached to the mounting surface using appropriate screws inserted through the mounting tabs on the module.
Wall mounting the HSC3020CP enclosure
The following diagram indicates the mounting location of the alarm controller PCB, wireless receiver, power supply module
and tamper bracket inside the HSC3020CP enclosure.
- 13 -
Figure 2-4 HSC3020CP enclosure
A Tamper screws
Note: The HSC3020CP is used only for EN50131 and NFA2P certified installations.
HSM3204CX/HSM3350 mounting location in HSC3010C
The following diagram indicates the mounting location of the HSM3204CX/HSM3350, power supply module and tamper
bracket inside HSC3010C/ HSC3010CR/ HSC3030CAR and HSC3020 enclosures.
Figure 2-5 HSM3304CX/HSM3350 mounted in HSC3010C, HSC3010CR, HSC3030CAR enclosures
HSM3408 in HSC3010 enclosure

The following diagram indicates the routing of power limited and non-power limited wiring inside the enclosure. Battery
leads and AC cord are non-power limited. All other wiring is power limited.
- 14 -
Figure 2-6 HSM3408 in HSC3010C enclosure
HSM3408 and HSM3350 mounting in HSC3020C enclosure

The following diagram indicates the available mounting locations of the HSM3350, HSM3408, power supply module and
tamper bracket inside the HSC3020C enclosure.
Figure 2-7 HSM3408 and HSM3350 modules in HSC3020C enclosure
HSM3350
HSM3408
HSM3408
HSM3408
- 15 -
HSM2108/HSM2208 mounting locations in HSC3010 enclosure

The following diagram indicates all available mounting locations of the HSM2108/HSM2208 inside HSC3010C/
HSC3010CR/ HSC3030CAR and HSC3020 enclosures.
Figure 2-8 HSM2108/HSM2208 mounted in HSC3010C, HSC3010CR, HSC3030CAR enclosures
- 16 -
2.3 General wiring instructions

To connect the wiring for the PowerSeries Pro, complete the following steps:
1. Ensure all wires are secured to the enclosure using cable ties. See figure 2-8 to figure 2-14 for locations.
2. Route the AC line into the enclosure through the provided opening, as indicated in figure 2-8.
3. Route the DC wires to the alarm controller as shown. Use cable ties to secure the DC wires to the enclosure.
4. Route wiring for modules and other devices into the enclosure through provided openings. Remove knockouts as
required.
Note: For HSC3030CAR attack-resistant enclosure, all unused holes must be covered by plastic plugs (shipped with cab-
inet).
This diagram shows routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord
are non-power limited. All other wiring is power limited.
Figure 2-9 Panel wiring for HSC3010C
For HSC3010C installations, complete the following steps:

1. If mounting the power supply inside the cabinet, attach it as per figure 2-4 using supplied hardware. Use cable ties to
secure the DC wires to the enclosure.
IMPORTANT!
Minimum 1/4-inch (6.4 mm) separation must be maintained at all points between battery/AC wiring and all other wiring con-
nections. Do NOT route any wiring over circuit boards. Maintain at least 1 inch (25.4 mm) separation.
2. Install the grommet strip (available separately – p/n 57000933) into the opening on back of cabinet as indicated in figure
2-4. Route the AC cable out of the enclosure through the opening indicated in the diagram.
3. If mounting the power supply outside the enclosure, attach it to the wall using suitable hardware. Route DC wires into the
enclosure and secure them with cable ties. See figure 2-4 for approved wire length/gauge.
Note: For ULC commercial Fire applications, use enclosure model HSC3010CR.
- 17 -
HS3032/HS3128/HS3248 in HSC3020C NA Wiring Diagram

Figure 2-10 Panel wiring for HSC3020C (for North America)
POWER LIMITED
Cable ties (not supplied) recommended
Use metal standoff and screw in the position
indicated.
Tamper switch and
IMPORTANT! Ensure screw and standoff are tightly
mounting bracket
secured to establish Earth ground connection.
PC LINK MICRO-B
USB TYPE A
STAND OFF
PC BOARD
CABINET HS3032/HS3128/HS3248
Warning: Disconnect AC power and
telephone lines before servicing.
1. Insert standoff into cabinet
mounting hole in the desired
location. Snap in place.
2. Position circuit board mounting
holes over standoffs. Press firmly
on board to snap in place.
Cable tie required

Power supply
mounting screws
4Ah
7Ah
2 x 7Ah
17Ah
Cable tie required
This diagram shows routing of power limited and non-power Primary: 120V AC, 60Hz, Class VI
limited wiring inside the enclosure. Battery leads and AC cord Secondary: 18V DC, 3.6A Grommet strip (Not supplied)
are non-power limited. All other wiring is Power limited. Power adaptor module: HS65WPSNA Part# 57000933
Note: Do not connect power adaptor
module to a receptacle controlled by a
switch
Note: Power adaptor module may be mounted
outside the cabinet. Use the following guide to
determine sutiable distance and guage:
DISTANCE GAUGE
2 meters/6.5ft 22AWG
3 meters/10ft 20AWG
4 meters/13ft 18AWG

1. If mounting the power supply inside the cabinet, attach it as per figure 2-9 using supplied hardware. Use cable ties to
secure the DC wires to the enclosure.
IMPORTANT!
Minimum 1/4-inch (6.4 mm) separation must be maintained at all points between battery/AC wiring and all other wiring con-
nections. Do NOT route any wiring over circuit boards. Maintain at least 1 inch (25.4 mm) separation.
2. Install the grommet strip (available separately – p/n 57000933) into the opening on back of cabinet as indicated in figure
2-4. Route the AC cable out of the enclosure through the opening indicated in the diagram.
3. If mounting the power supply outside the enclosure, attach it to the wall using suitable hardware. Route DC wires into the
enclosure and secure them with cable ties. See figure 2-9 for approved wire length/gauge.
- 18 -
Installing the HSM3204CX in HSC3010C enclosure

Figure 2-11 HSM3204CX in HSC3010C enclosure
POWER LIMITED
PC BOARD
STAND OFF
HSM3204CX
Warning: Disconnect AC power
before servicing.
CABINET

on board to snap in place. Tamper switch and mounting bracket
Wire tamper switch to any Corbus zone.
Program zone as 24-Hour Latching or Non-Latching tamper.
Supports NC, EOL or DEOL supervision.
Primary: 120VAC, 60Hz, Class VI

Secondary: 18V DC, 3.6A
Power adapter module: HS65WPSNA
Note: Do not connect Power adapter
module to receptacle controlled by a switch
Plastic grommet strip (Not supplied) recommmended

4Ah
Red - 7Ah Cable tie required
2 x 7Ah
Cable tie required
Black + 17Ah Power supply mounting screws
Note: Power supply may be mounted outside the

cabinet. Use the following guide to determine
sutiable distance and guage:
DISTANCE GAUGE
3 meters/10ft 20AWG
4 meters/13ft 18AWG
- 19 -
HSM3204CX in HSC3020C North American wiring diagram

Figure 2-12 North American wiring for HSM3204CX in HSC3020C enclosure
POWER LIMITED
Tamper switch and

mounting bracket
STAND OFF
HSM3204CX
PC BOARD Warning: Disconnect AC power
before servicing.
CABINET

Cable tie required

Power supply
mounting screws
4Ah
7Ah
2 x 7Ah
17Ah
Cable tie required
limited wiring inside the enclosure. Battery leads and AC cord Secondary: 18V DC, 3.6A
are non-power limited. All other wiring is Power limited. Power adaptor module: HS65WPSNA Grommet strip (Not supplied)
Note: Do not connect power adaptor Part# 57000933
switch
DISTANCE GAUGE
3 meters/10ft 20AWG
4 meters/13ft 18AWG
- 20 -
Installing the HSM3350 in the HSC3010C enclosure

Figure 2-13 HSM3350 in HSC3010C enclosure
POWER LIMITED
STAND OFF
PC BOARD
HSM3350
Warning: Disconnect AC power
CABINET before servicing.

on board to snap in place. Tamper switch and mounting bracket
Wire tamper switch to any Corbus zone.
Program zone as 24-Hour Latching or Non-Latching tamper.
Supports NC, EOL or DEOL supervision.
Primary: 120VAC, 60Hz, Class VI

Secondary: 18V DC, 3.6A
Power adapter module: HS65WPSNA
Note: Do not connect Power adapter
module to receptacle controlled by a switch
Plastic grommet strip (Not supplied) recommmended

4Ah
Red - 7Ah Cable tie required
2 x 7Ah
Cable tie required
Black + 17Ah Power supply mounting screws
Note: Power supply may be mounted outside the

cabinet. Use the following guide to determine
sutiable distance and guage:
DISTANCE GAUGE
3 meters/10ft 20AWG
4 meters/13ft 18AWG
- 21 -
North American wiring for HSM3350 in the HSC3020C enclosure

Figure 2-14 North American wiring for HSM3350 in the HSC3020C enclosure
POWER LIMITED
Tamper switch and

mounting bracket STAND OFF
PC BOARD
HSM3350
Warning: Disconnect AC power CABINET
before servicing.

Cable tie required
Power supply
mounting screws
4Ah
7Ah
2 x 7Ah
17Ah
Cable tie required
limited wiring inside the enclosure. Battery leads and AC cord Secondary: 18V DC, 3.6A Grommet strip (Not supplied)
are non-power limited. All other wiring is Power limited. Power adaptor module: HS65WPSNA Part# 57000933
Note: Do not connect power adaptor
switch
DISTANCE GAUGE
3 meters/10ft 20AWG
4 meters/13ft 18AWG
- 22 -
Installing the HS3032/HS3128/HS3248 in the HSC3020C enclosure

Figure 2-15 Panel Wiring for HSC3020C enclosure
POWER LIMITED
Cable ties (not supplied) recommended STANDOFF
PC BOARD
Tamper switch
and mounting
bracket
PC LINK
USB TYPE A
MICRO-B CABINET
1. Insert standoff into cabinet mounting hole in the

HS3032/HS3128/ desired location. The standoff makes an audible
“click” when properly inserted.
HS3248 2. Position circuit board mounting holes over
Use No. 14-22 AWG size wire
standoffs. Press firmly on board to snap in place.
UA718
BATTERY
indicated.
Cable tie
required
Cable tie
1x17 Ah/12V or for NFA2P required
1X18Ah/12V sealed lead

acid type battery To power adaptor AC IN
module (Blue-Neutral) (Blue-Neutral)
To power adaptor module EGND
(Green/Yellow-EGND) (Green/Yellow)
To power adaptor AC in
module (Brown-Live) (Brown-Live)
Replace fuse with same type (20 mm) rated

250V/3.15A Slow Blow
Power supply Primary: 100-240V AC, 50-60Hz, Class 6
mounting screws Secondary: 18V DC, 3.6A
Power adaptor: HS65WPS

1. Route the AC line through the opening on the bottom of the cabinet and secure using cable tie as shown in figure 2-14.
2. Connect AC wires to the fuse block as shown.
Note: Position cable ties over cable insulation, not directly on the exposed AC wires.
WARNING: Incorrect connections may result in PTC failure or improper operation. Inspect wiring and ensure connections
are correct before applying power.
EN installation notes
1. The connection to the mains supply must be made as per the local authorities’ rules and regulations: In the UK as per
BS6701. An appropriate disconnect device must be provided as part of the building installation. Where it is not possible to
rely on identification of the NEUTRAL in the AC MAINS SUPPLY, the disconnecting device must disconnect both poles sim-
ultaneously (LINE and NEUTRAL). The device shall disconnect the supply during servicing.
2. The equipment enclosure must be secured to the building structure before operation.
3. Disposal of used batteries shall be made according to the waste recovery and recycling regulations applicable to the
intended market
4. Two batteries may be used to provide the required backup time.
WARNING:
High Voltage: Disconnect AC Power and telephone lines before servicing.
The following modules are optional:
l One slot for a HSM3350 with one 17Ah battery and internally mounted HS65WPS power supply
l Two slots for HSM3408, HSM2955, HSM3204CX
- 23 -
HSC3020CP wiring
Figure 2-16 Panel wiring for HSC3020CP enclosure
The HSC3020CP enclosure ships with the alarm panel, HS65WPS module, power supply and tamper switch already
installed. The communicator, case tamper switch, battery, and AC must be wired during installation.
For HSC3020CP plastic enclosure installations, complete the following steps:
1. Route the AC line in through the opening on the bottom of the cabinet and secure using cable tie as shown in figure 2-
15.
2. Connect AC wires to the fuse block as shown.
Note: Position cable ties over cable insulation, not directly on the exposed AC wires.
- 24 -
HSM3204CX in HSC3020CP wiring diagram

Figure 2-17 Panel wiring for HSC3020CP enclosure
- 25 -
HSM3350 in HSC3020CP international wiring diagram

Figure 2-18 HSM3350 wiring for HSC3020CP enclosure
- 26 -
Terminal descriptions
The following terminals are available on the PowerSeries Pro alarm controller.
Table 2-1 Terminal descriptions
Terminal Description
BAT+, BAT- Battery terminals. Use to provide backup power during a power outage and additional current when system demands exceed the
power output of power adapter, short term such as when the system is in alarm.
Do not connect the battery until all other wiring is complete.
DC +, DC - The HS65WPS power adapter supplies 18 VDC power input to the alarm controller.
Note: For CE/EN certified applications, the name of the power , the name of the power adapter is HS65WPS. For UL/ULC listed
applications, the name of the power adapter is HS65WPSNA. For ULC Commercial Fire Listed applications and ULC Commercial
Burg Security Level 4 applications, the name of the power adapter is HS65WPSNAS.
Connect the battery before connecting the AC. Do not connect the battery or power adapter until all other wiring is complete.
AUX+, AUX- Auxiliary terminals. Use to power detectors, relays, LEDs, etc. (2 A max). Connect the positive side of device to one of the three
AUX+ terminals and the negative side to AUX- or COM.
BELL+, Bell/Siren power (700 mA continous, 2A max short term). Connect the positive side of any alarm warning device to BELL+, the
BELL- negative side to BELL-.
Note: For EN50131 and UL/ULC listed applications, use maximum 700 mA load on the BELL output.
RED, BLK, Corbus terminals. Use to provide power and communication between the alarm controller and connected modules. Each module
YEL, GRN has four Corbus terminals that must be connected to the Corbus.
PGM1 to Programmable output terminals. Use to activate devices such as LEDs, relays, buzzers, etc.
PGM4 (PGM1, PGM4: 100 mA; PGM2: 300 mA or can be configured for use as a 2-wire smoke detector interface, max loop current 100
mA;
PGM3: 300 mA (negative trigger) or 1 A (positive trigger)
Z1 to Z8 Zone input terminals. Ideally, each zone should have one detection device; however, multiple detection devices can be wired to the
COM same zone.
EGND Earth ground connection

ETHERNET Ethernet port
TIP, RING, Telephone line terminals
T-1, R-1
*x= none use for CE/EN certified applications

x= NA use for UL/ULC listed applications
x= NAS use for ULC Commercial Fire Listed applications and ULC Commercial Burg Security Level 4 applications.
Wire routing for power & non-power limited

See "Wiring diagrams" on page 276 for expanded diagrams.
Note: Wire entry for power limited wiring must be separated by a different entry access from non-power limited wiring.
Corbus wiring
The RED and BLK Corbus terminals are used to provide power while YEL and GRN are used for data communications. The
4 Corbus terminals of the alarm controller must be connected to the 4 Corbus terminals or wires of each module.
The following conditions apply:
l Corbus should be run with 18 to 22 AWG quad, two pair twisted preferred.
l The modules can be home run to the panel, connected in series or can be T-tapped.
l Do not use shielded wire for Corbus wiring.
Note: Any module can be connected anywhere along the Corbus. Separate wire runs for keypads, zone expanders etc. are
not necessary.
- 27 -
Note: No module can be more than 1000 ft / 305 m (in wire length) from the panel. Do not use shielded wire for
Corbus wiring.
Figure 2-19 Corbus wiring
Module (A) is wired correctly as it is within 1000 ft / 305 m of the panel, in wire distance. Module (B) is wired correctly as it is
within 1000 ft / 305 m of the panel, in wire distance. Module (C) is NOT wired correctly as it is farther than 1000 ft / 305 m
from the panel. For models that require more than 1000 ft / 305 m from the main panel, a HSM3204CX power supply/Corbus
extender can be used.
Current ratings
In order for the system to operate properly, the power output of the alarm controller and power supply modules cannot be
exceeded. Use the following data to ensure that the available current is not exceeded.
Table 2-2 System output ratings
Device Output Rating (12 V DC)
HS3032 AUX/ 2 A. Subtract the listed rating for each keypad, expansion module and accessory connected to AUX or Corbus. At least
HS3128 Corbus: 100 mA must be reserved for the Corbus.
HS3248 BELL: 700 mA continuous rating. 2 A. short term. Available only with standby battery connected. DO NOT exceed the 700 mA
load for UL/ULC or EN certified applications.
HSM3350 AUX1: 3 A. Subtract the listed rating for each keypad, expansion module and accessory connected to AUX.
AUX2:
HSM3408 AUX: 500 mA. Continuous rating. Subtract for each device connected. Subtract the total load on this terminal from the alarm
panel AUX/Corbus output.
HSM3204CX AUX/ 2 A. Continuous rating. Subtract for each device connected.
Corbus:
HSM2208 AUX: 250 mA. Continuous rating. Subtract for each device connected. Subtract the total load on this terminal from the alarm
panel AUX/Corbus output.
HSM2108 AUX: 100 mA. Subtract for each device connected. Subtract the total load on this terminal from the panel AUX/Corbus output.
- 28 -
Alarm controller current calculation

Maximum (standby or alarm)
AUX (2 A max. including PGMs 1-4)
Corbus (2 A max.)***
PCLink+ (200 mA)
USB (500 mA max.)
Cell module (20 mA idle)
Total (must not exceed 2 A)
For UL, ULC and Commercial Listed applications, the total standby and alarm current cannot exceed 2 A.
Note: For EN50131, UL, ULC and Commercial Listed applications, the total standby and alarm current cannot exceed the
values in Aux Loading and Battery Selection for the applicable type of installation.
Overcurrent trouble
If the total current of the panel internal components and all outputs exceeds a threshold of 2.1 A for a period longer than 5
minutes, an overcurrent trouble is generated. When the current goes below a 2.0 A threshold, the trouble restores. Do not
exceed 2.0 A combined between AUX and Corbus.
Note: Total current does not include bell current or battery charging.
Line loss
Voltage loss through wire resistance must be considered for all installations. To ensure proper operation, at least 12.5 VDC
must be applied to all modules on the system (when AC is connected and the battery is fully charged). If less than 12.5 VDC
is applied, system operation is adversely affected.
To correct the problem, try any or all of the following:
1. Connect a HSM2300/2204/3350/3204CX power supply between the alarm controller and the module to provide addi-
tional power to the Corbus.
2. Reduce the length of the Corbus run to the module.
3. Increase the gauge of wire.
- 29 -
Capacitance limits
An increase in capacitance on the Corbus affects data transmission and causes the system to slow down. Capacitance
increases for every foot of wire added to the Corbus. The capacitance rating of the wire used will determine the maximum
length of the Corbus.
For example, 22-gauge, non-shielded, 4-conductor wire has a typical capacitance rating of 20 picofarads per foot (which is
20 nF/1000 ft). For every 1000 feet of wire added – regardless of where it is run – the capacitance of the Corbus increases
by 20 nF.
The following table indicates the total wire distance allowed for the capacitance rating of the wire used:
Table 2-3 Wire capacitance
Wire Capacitance per 1000 ft (300 m) Total Corbus Wire Length
15 nF 5300 ft/1616 m
20 nF 4000 ft/1220 m
25 nF 3200 ft/976 m
30 nF 2666 ft/810 m
35 nF 2280 ft/693 m
40 nF 2000 ft/608 m
2.4 Installing modules

Remove all power from the system while connecting modules to the alarm controller.
Zone expanders
The main alarm controller has connection terminals for zones 1 to 8. Additional HSM2108 and HSM3408 zone expanders
may be added to increase the number of zones on the system. Each zone expander consists of one group of 8 zones. At
enrollment, the zone expander is automatically assigned to the next available 8-zone expander slot/Corbus expander slot.
Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the alarm panel. Board current draw: 30 mA.
Figure 2-20 HSM2108 zone expander
- 30 -
Figure 2-21 HSM3408 8-zone expansion
Refer to the HSM2108 and HSM3408 installation sheets for more information.
2-way audio module

The HSM2955 2-way audio module provides Talk/Listen-in capability for the audio verification of alarms.
The main alarm controller has a 3-pin analog audio link interface to connect the module.
Figure 2-22 HSM2955 2-way audio module
Output expander
The HSM2208 module is used to add up to 8 low-current programmable outputs to the alarm system.
The 4-wire Corbus connection is used by the panel to communicate with the module. Connect the RED, BLK, YEL and GRN
terminals to the Corbus terminals on the alarm panel. Board current draw: 40 mA.
Figure 2-23 HSM2208 output expander
- 31 -
Wireless transceiver module

The HSM2HOSTx 2-way wireless module provides communication between wireless devices and the alarm controller.
Note: The HSM2HOST must be used with the HSC3020CP plastic enclosure, or in its own separate enclosure.
Connect the HSM2HOSTx to the 4-wire Corbus of the alarm controller according to the following diagram.
Figure 2-24 HSM2HOSTx wiring diagram
After you have completed the wiring, reconnect power to the security system. Board current draw: 35 mA
Power supply wiring

HSM2300/2204
The HSM2300/2204 power supply/high-current output module provides up to 1 A of additional current and can be used to
add up to four programmable outputs (HSM2204 only) to the alarm system.
The 4-wire Corbus connection provides communication between the module and alarm panel. Connect the RED, BLK, YEL
and GRN terminals to the Corbus terminals on the alarm controller. If O1 is not used, connect to Aux+ with a 1 K resistor.
Board current draw: 35 mA.
Figure 2-25 HSM2300/2204 power supply wiring
UL/ULC residential
fire applications Residential
Burglary
CON1
BAT+ BAT-
RED*
BLK*
GRN
YEL
BATTERY 2 BATTERY 1 BATTERY

12V 7Ah 12V 7Ah 120VAC/
12V 7Ah
Maximum battery Maximum battery 60Hz
Same rating as charge current is charge current is Primary
Battery 1 360 mA 360 mA
TO
TRANSFORMER BLK
16.5VAC / 40VA
Battery standby capacity is at least for 24 hours for PTD1640U / RED
Fire Applications. PTD1640 AUX** BLK KEYBUS
TO CONNECTION
EXPANSION YEL TO CONTROL
Recommended Battery: DSC model BD7-12. MODULE PANEL
EU, South Africa, GRN
Australia, NZ etc:
primary 230VAC/ 50/60Hz
* Red, Blk, 12 VDC @ 20mA

** Refer to the Specifications Chart above for
the maximum current draw.
- 32 -
HSM3350
The HSM3350 is a supervised 3 A, 12 VDC power supply module with dual AUX outputs and dual battery backups.
The 4-wire Corbus connection provides communication between the module and alarm panel. Connect the RED, BLK, YEL
and GRN terminals to the Corbus terminals on the alarm controller.
Figure 2-26 HSM3350 power supply wiring
NOTE: Fire and Security
WARNING! devices that require power
High Voltage from the HSM3350 shall be
UA720
Rev03 UL/ULC Listed for the
Disconnect AC power
intended application and
lines prior to servicing operate over the range 10.8
All circuits are classified for UL installations as power limited/Class II power limited, Status VDC - 12.5VDC.
except for the battery leads which are not power limited. Do not route any wiring LED
over circuit boards. Maintain at least 1” (25.4 mm) separation. A minimum of 1/4”
(6.4 mm) separation must be maintained at all points between power limited wiring
and all other non-power limited wiring. Inspect wiring and ensure connections are
correct before applying power.
+ AUX1 - + AUX2 -
+BAT1- +BAT2- + DC - CORBUS + TAM -

RED BLK YEL GRN
+ RED - BLK + RED - BLK

N.C. tamper contact. Connect to AUX output ratings:
tamper switch installed in the UL/ULC applications 10.8 VDC - 12.5 VDC / 3 A
Battery Battery cabinet for door/cover removal,
or removing from mounting
max.
EN50131 applications 10 Vdc-14 Vdc/3 A max
12 Vdc 12 Vdc location tamper detection. Supervised.
4/7/17 Ah 7 Ah CORBUS, connects to the main

control panel communications bus
(HS3032, HS3128, HS3248).
Switching Mode Power Adapter

NOTE: Refer to the Installation Manual for proper Model HS65WPSNA is required for UL/ULC listed installations. It can be installed inside the metal enclosure model HSC3010C or
selection of battery capacity based on the intended outside of it, cord connected to AC mains.
application and maximum loading allowed. For ULC Commercial Fire or ULC Commercial Burg Security Level IV applications use model HS65WPSNAS, installed inside the
NOTE: BAT 2 shall be enabled in programming. metal enclosure model HSC3010CR or HSC3010C (using high voltage barrier kit), hardwired connection to AC mains.
Primary Input: 120 VAC/50 Hz/1.7 A Max
Primary input: Output: 18 VDC/3.6 A Max
UL/ULC applications: 120 VAC/60 Hz 1.7 A Model HS65WPS is required for CE/EN50131 certified applications. It shall be installed inside the metal cabinet model HSC3020C,
(cord connected) hardwired connections to AC mains.
CE/EN50131 applications: 230 VAC/ 50 Hz Primary Input: 230 VAC/60 Hz/1.7 A Max
1.7 A (hardwired) Output: 18VDC/3.6A Max
NOTE: Do not connect power adapter to

receptacle conrolled by a switch.
- 33 -
Corbus repeater
The HSM3204CX is a Corbus repeater and isolator module with four high current relay outputs. The module has an on-
board power supply to power Corbus.
Figure 2-27 HSM3204CX Corbus repeater
NOTE: Fire and

Security Status LED UA721
devices that WARNING!
require power High Voltage
from the Disconnect AC power
HSM3204CX lines prior to servicing
shall be
UL/ULC (or All circuits are classified for Ul installations as power limited/Class II power
cUL) Listed for limited, except for the battery leads which are not power limited. Do not route
the intended any wiring over circuit boards. Maintain at least 1” (25.4 mm) separation. A
application and minimum of 1/4” (6.4 mm) separation must be maintained at all points
operate over between power limited wiring and all other non-power limited wiring. Inspect
wiring and ensure connections are correct before applying power.
the range 10.8
VDC - 12.5 VDC.
+BAT-
DC CORBUS IN CORBUS OUT TAM AUX RLY1 RLY2 RLY3 RLY4
_ _
+_ RED BLK YEL GRN RED BLK YEL GRN + + NO COM NC NO COM NC NO COM NC NO COM NC
PGM relay outputs (NC/NO contacts)

Separately energized
Ratings: 30 VDC/2 A, pf = 0.6
AUX output ratings:

UL/ULC applications: 10.8 Vdc - 12.5 Vdc/2 A max
EN50131 applications: 10 VDC - 14 VDC / 2 A max.
CORBUS IN connects to the N.C. tamper contact. Connect to Supervised.
main control panel tamper switch installed in the
communications bus cabinet for door/cover removal, or
(HS3032, HS3128, HS3248). removing from mounting location
+ RED - BLK + RED - BLK tamper detection.
CORBUS OUT, shared with AUX output.

Battery Battery UL/ULC applications: 10.8 VDC - 12.5 VDC / 2 A max.
12 VDC EN50131 applications: 10 VDC - 14 VDC / 2 A max.
12 VDC Supervised.
Minimum Minimum Provides alarm system bus connection to more modules (used in large installations).
4/7/17 Ah 7 Ah
NOTE: Do not connect

NOTE: Refer to the power adapter to
Installation Manual for receptacle controlled by a
proper selection of switch.
battery capacity based Switching Mode Power Adapter
on the intended Model HS65WPSNA is required for UL/ULC listed installations. It can be installed inside the metal enclosure
application and model HSC3010C or outside of it, cord connected to AC mains.
maximum loading For ULC Commercial Fire or ULC Commercial Burg Security Level IV applications use model HS65WPSNAS,
allowed. installed inside the metal enclosure model HSC3010CR or HSC3010C (using high voltage barrier kit), hardwired
connection to AC mains.
Output: 18 VDC/3.6 A Max
Model HS65WPS is required for CE/EN50131 certified applications. It shall be installed inside the metal cabinet
model HSC3020C, hardwired connections to AC mains (see wiring diagram below).
Output: 18VDC/3.6A Max
Keypad Wiring
To wire a keypad to the alarm controller, remove the keypad backplate (refer to the keypad installation sheet) and connect
the RED, BLK, YEL and GRN terminals to the corresponding terminals on the alarm controller.
Keypad zone/PGM wiring
Hardwired devices can be connected to hardwired keypads with inputs (zone) or outputs (PGM). This saves from running
wires back to the control panel for every device.
To connect a zone device to HS2LCDPRO and HS2TCHPRO(BLK) keypads, run one wire to the P/Z terminal and the other
to B. For powered devices, use red and black to supply power to the device. Run the red wire to the R (positive) terminal and
the black wire to the B (negative) terminal.
Keypad zones support Normally Closed Loops, Single End of Line, Double End of Line, and Triple End of Line resistors.
To connect the PGM output, run one wire to the P/Z terminal and the other to R.
- 34 -
Figure 2-28 Keypad P/Z terminals
Note: When using end of line supervision, connect the zone according to one of the configurations outlined in "Zone wiring"
on page 35. End of line resistors must be placed on the device end of the loop, not at the keypad.
Assigning keypad zones
When using keypad zone inputs, each input used must be assigned a zone number in Installer Programming.
First, ensure that you have enrolled all installed keypads into the desired slots (See "[902] Add/Remove Modules" on page
149). Next, assign keypad zones by entering programming section [861]-[876], subsection 011 for keypads 1-16. Enter a 3-
digit zone number for each of the keypad zones. This number must be programmed into the slot location that the keypad is
assigned to.
Note: A keypad zone overrides the corresponding hardwired or wireless zone.
Once the keypad zones are assigned, you must also program zone definitions and zone attributes. See "[001] Zone types"
on page 78 and See "Zone setup" on page 78.
HSM2955 wiring
For wiring information refer to HSM2955 Installation manual #29010198xxx.
Zone wiring
Power down the alarm controller and complete all zone wiring.
Zones can be wired to supervise normally open devices (e.g., smoke detectors) or normally closed devices (e.g., door con-
tacts). The alarm panel can also be programmed for single end-of-line, double end-of-line, and triple-end of line resistors.
Zone programming is done using the following programming sections:
l [001] selects zone definition
l [013] Opt [1] for normally closed or EOL; Opt [2] for SEOL or DEOL
l [201 - 208] partition assignment.
Alternately, zones may be individually configured as NC, SEOL, DEOL or TEOL through section [002] Zone Attributes,
toggles 9,10, 11 and 15, which will override the option in [013].
Observe the following guidelines when wiring zones:
l For UL listed installations use SEOL or DEOL only
l Minimum 22 AWG wire, maximum 18 AWG
l Do not use shielded wire
l Do not exceed 100 Ω wire resistance. Refer to the following table:
Table 2-4 Burglary zone wiring chart
Wire gauge Maximum length to EOL resistor (ft/meters)
22 3000 / 914
20 4900 / 1493
19 6200 / 1889
18 7800 / 2377
Figures are based on maximum wiring resistance of 100Ω.
- 35 -
Normally closed
Connect hardwired devices to any Z terminal and any COM terminal. Wire normally closed devices in series.
Note: For UL Installations, do not use normally closed loops.
Figure 2-29 Normally closed
The following table shows zone status under certain conditions for NC Loops:
Table 2-5 NC loop status
Loop resistance Loop status
0Ω (shorted wire, loop shorted) Secure
Infinite (broken wire, loop open) Violated
Single end-of-Line (SEOL) resistor

When SEOL resistors are installed at the end of a zone loop, the alarm panel detects if the circuit is secure, open, or shorted.
The SEOL resistor must be installed at the end of the loop for proper supervision.
To enable SEOL supervision, program section [013], options [1] and [2] to OFF. To configure SEOL supervision per zone,
use programming section [002], bit 10.
Note: This option should be selected if either normally closed or normally open detection devices or contacts are used.
Figure 2-30 SEOL wiring
The following table shows zone status under certain conditions for SEOL:
- 36 -
Table 2-6 SEOL loop status

0 Ω (shorted wire, loop shorted) Violated
5600 Ω (contact closed) Secure
Infinite (broken wire, loop open) Violated
Double end of Line (DEOL) resistors

When double end-of-line (DEOL) resistors are installed at the end of a zone loop, the second resistor enables the panel to
determine if the zone is in open, closed, tampered or faulted.
Note: Any zone programmed for Fire or 24-hr Supervisory must be wired with a SEOL resistor regardless of the type of zone
wiring supervision selected for the panel. If you change the zone supervision options from DEOL to SEOL or from NC to
DEOL, power the system down completely, then power it back up for correct operation.To enable DEOL supervision per
zone, program section [013], option [1] to OFF and option [2] to ON. To configure DEOL supervision per zone, use pro-
gramming section [002], bit 11.
Figure 2-31 DEOL wiring
Note: If the DEOL supervision option is enabled, all hardwired zones must be wired for DEOL resistors, except for Fire and
24 Hour Supervisory zones. Do not use DEOL resistors for Fire zones or 24 Hour Supervisory zones.
Note: Do not wire Fire zones to keypad zone terminals if the DEOL supervision option is selected.
Note: This option can only be selected if N/C detection devices or contacts are used. Only one N/C contact can be con-
nected to each zone.
The following table shows zone status under certain conditions for DEOL:
Table 2-7 DEOL loop status
0 Ω (shorted wire, loop shorted) Fault
5600 Ω (contact closed) Secure
Infinite (broken wire, loop open) Tamper
11200 Ω (contact open) Violated
Triple end-of-line (TEOL) resistor

The TEOL resistor supervises anti-masking functionality in hardwired motion detectors. To configure TEOL supervision per
zone, use programming section [002], bit 15.
- 37 -
Figure 2-32 TEOL wiring
The following table shows zone status under certain conditions for TEOL:
Table 2-8 TEOL loop status
0 Ω (short) Fault
Infinite Ω (open) Tamper
5600 Ω Restored
11200 Ω Alarm
21200 Ω (alarm and fault/mask) Mask
15600 Ω (fault/mask) Fault
Note: Resistor values are configurable in section [004].
PGM wiring
Min/max operating voltages for devices, sensors and modules is
9.8 V DC - 14 V DC.
PGMs switch to ground when activated from the alarm controller. Connect the positive side of the device to the AUX+ ter-
minal and the negative side to a PGM terminal.
PGM 1, and 4 supply up to 100 mA; PGM 2 and 3 supply up to 300 mA.
A relay is required for current levels that exceed the maximum limits.
PGM2 can also be used for two-wire smoke detectors or 24-hour burglary input alarm.
Note: Use only SEOL resistors on Fire zones.
- 38 -
Figure 2-33 LED output with current limiting resistor and optional relay driver output.
UL Compatibility ID For FSA-210B Series is: FS200

Note: For ULC listed installations, use FSA-210A and FSA-410A series.
Bell wiring
These terminals supply 700 mA of current at 10.8 - 12.5 VDC for commercial/ residential installations. To comply with NFPA
72 Temporal Three Pattern requirements, section [013] Opt [8] must be ON. Note that steady, pulsed alarms are also sup-
ported. Temporal 4 cadence for CO alarm notification is also supported.
Figure 2-34 Bell wiring
The Bell output is supervised and power limited by 2 A hardware protection. If unused, connect a 1000 Ω resistor across
Bell+ and Bell- to prevent the panel from displaying a trouble. See "Troubleshooting" on page 59.
Telephone line wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x connector as indicated in the following diagram.
For connection of multiple devices to the telephone line, wire in the sequence indicated. Use 26 AWG wire minimum for wir-
ing.
Figure 2-35 Telephone line wiring
Note: Ensure that all plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C.F.R. Part 68,
Sub-Part F. For proper operation, no other telephone equipment must be connected between the control panel and the tele-
phone company facilities.
- 39 -
Smoke detector wiring

All zones defined as Fire must be wired according to the following diagram:
Figure 2-36 Smoke detector wiring
See "[001] Zone types" on page 78 for fire zone operation.

Note: Smoke detectors must be latching type. To reset a smoke detector, enter [*][7][2].
Table 2-9 Compatible 4-wire smoke detectors
FSA-410x FSA-410xLST FSA-410xRST
FSA-410xT FSA-410xR FSA-410xLRST
FSA-410xS FSA-410xRT
FSA-410xST FSA-410xRS
Current ratings for DSC FSA-410 Series: 25mA - 90mA
Fire zone wiring: 2-wire smoke detectors

If PGM 2 is programmed for 2-wire smoke detector connection, the detectors must be wired according to the following dia-
gram:
Figure 2-37 2-wire smoke detector wiring
Note: Additional 2-wire smoke detectors must be connected in parallel as shown above. The maximum number of smoke
detectors on a 2-wire loop is 18.
Note: Do not combine smoke detector models from different manufacturers on the same circuit. Operation may be impaired.
Refer to the smoke detector installation sheet when positioning detectors.
- 40 -
Table 2-10 Compatible 2-wire smoke detectors

FSA-210x FSA-210xR
FSA-210xT FSA-210xRT
FSA-210xS FSA-210xRS
FSA-210xST FSA-210xRST
FSA-210xLST FSA-210xLRST
Current ratings for DSC FSA-210B series: 35mA - 75mA
Table 2-11 2-wire smoke detector initiating circuit

Item Specification
Style/Class, Supervised, Power Limited Style B (Class B)
Compatibility Identifier PC18-1
DC Output Voltage 9.8-13.8 VDC
Detector Load 2mA (MAX)
Single End-of-Line Resistor (SEOL) 2200Ω
Loop Resistance 24Ω (MAX)
Standby Impedance 1020Ω (NOM)
Alarm Impedance 570Ω (MAX)
Alarm Current 89mA (MAX)
CO detector
The following hardwired CO detector models can be used with PowerSeries Pro alarm controllers:
l Potter Model CO-12/24, UL File E321434
l Quantum Model 12-24SIR, UL File E186246
l NAPCO Model FW-CO12 or FW-CO1224, UL File E306780
l System Sensor Model CO1224, UL File E307195
Note: For multiple unit connections, the leads between CO detectors must be broken. The power supervision relay must be
powered from the last detector in the loop.
Wireless CO detectors are also available. When installing wireless CO detectors, use only model PG9913UL, PG8913,
PG4913, or PGx933. An HSM2HOSTx (x=9UL/8/4) wireless receiver or HS2LCDRFPRO wireless keypad are required when
installing wireless CO detectors. For more details on these wireless devices, refer to their respective installation manuals.
Note: Use only UL approved devices with UL/ULC listed systems.
- 41 -
Table 2-12 CO detector ratings

Device Description Max rating @12 VDC
CO-12/24 Potter model CO detector 40 mA
12-24SIR Quantum model CO detector 75 mA
FW-CO12 NAPCO model CO detector 90 mA
FW-CO1224
CO1224 System Sensor model CO detector 40 mA
Figure 2-38 CO detector wiring

CO DETECTOR
POWER ALARM TROUBLE
- + NC C NO NC C NO
HS3032/HS3128/HS3248
AUX
+-
SEOL
ANY ANY
RESISTOR
COM Z
ZONE (5600Ω)
INPUT -
+
ALARM
(SEOL ZONE TYPE 41)
INITIATING
LOOP
RM-1/RM-2 RESISTANCE
POWER LOOP 100Ω
SUPERVISORY
RELAY
(12VDC, 35mA)
Earth ground wiring

Using the supplied insulated green wire, connect the earth ground terminal on the HS65WPSx power adapter to the earth
ground screw and nut assembly as shown in the diagram.
The earth ground screw and nut assembly must be mounted to the cabinet to one of the designated holes marked with the
earth ground symbol .

Figure 2-39 Earth ground installation
Item Description
1
1 Nut
2
2 Earth ground connection from building electrical installation.
3
Note: This ground connection goes to HS65WPSNA power
adapter EGND connections when this power adapter is mounted
4
in the cabinet.
5 3 Cabinet
4 Star washer
6 5 Bolt
6 Earth ground symbol
- 42 -
Connecting power
Batteries
Do not connect the battery until all other wiring is complete.
Note: A sealed, rechargeable, lead acid battery or gel type battery is required to meet UL requirements for power standby
times.
Connect the RED battery lead to the positive battery terminal and the BLACK battery lead to the negative battery terminal.
The panel can be programmed to charge the battery at 400 mA or 700 mA. (See "[982] Battery Settings" on page 152).
Note: Refer to "Aux loading and battery selection" on page 270.
Battery selection chart
After calculating the battery capacity (B) for each specific installation use the following table to determine the battery
required to support the main panel in standby mode for:
l 4 hours (UL/ULC residential burglary, ULC commercial burglary)
l 12 hours (EN50131 Grade 2/Class II)
l 24 hours (UL/ULC residential fire, UL home health care, ULC commercial burglary, ULC residential fire with wired
CO detectors UL985 6th Ed, ULC, fire commercial monitoring- no bell load allowed; INCERT [Belgium])
l 30 Hours (AC fail transmission required) or 60 hours (EN50131 Grade 3)
l 36 Hours (NFA2P 2 shield) or 60 hours (NFA2P 3 shield)
The battery size is measured in amp hours (Ah). The current values in the table denote the maximum current draw permitted
to achieve the desired standby time with the listed battery types.
Table 2-13 Standby battery guide
Battery size Desired standby time
4h 12 h 24 h 30 h 36 h 60 h
4 Ah 700 mA ------ ------ ------ ------ ------
7 Ah 1200 mA 500 ma 250 mA ------ ------ ------
14 Ah (2x7) 2000 mA 1000 mA 500 mA ------ ------ ------
17 Ah 2000 mA 1200 mA 600 mA 500 mA ------ 250 mA

18 Ah ------ ------ ------ 500 mA 450 mA 250 mA
* Use 2 x 7 Ah batteries connected in parallel, UL/ULC installations only

** with high current battery charge option enabled: [982].
Note: Battery capacity deteriorates with age and the number of charge/discharge cycles. Replace every 3-5 years.
Refer to "Regulatory approvals" on page 265. for detailed Aux. loading and battery charging information.
Complete the following chart to find (A), complete the following formula to find the battery capacity (B) and refer to the
HS3032/3128/HS3248 alarm controller battery selection chart above.
(Total standby current ________ mA (A) x Standby time ________ hours) + (Alarm current x Alarm time ________ hours \
1000) = _______ Ah (B)
Connecting AC power
The alarm controller requires an 18 VDC switched mode power supply. For information on connecting AC power, refer to Wir-
ing diagrams
- 43 -
Section 3: Configuration
3.1 Basic configuration steps
Once basic installation of the alarm panel is complete, the following general configuration options should be set:
l create partitions, See "Working with partitions " on page 47.
l assign keypads to partitions, see "Keypad partition setup " on page 48
l assign sirens to partitions, see "Bell/siren operation " on page 47
l set up partition account codes, see "Communications" on page 49
l set up partition timers, see "System times" on page 84
l enroll wireless modules and devices, see "Enrolling modules" on page 46
l assign zone types, see "[001] Zone types" on page 78, and attributes, see "[002] Zone attributes" on page 82
l create zone labels, see "Adding labels" on page 75
l add users, see "Assign access codes" on page 64
l set up the alternate communicator if equipped, see "Alternate communicator setup" on page 50
l program phone numbers, see "System Communications" on page 122
l set up call directions for the central monitoring station, see "System Communications" on page 122
l set up system timers, see "System times" on page 84
l configure reporting codes, see "Reporting" on page 116
l test the system, see "Testing the system" on page 51
3.2 Using the keypad

The PowerSeries Pro alarm panel is compatible with several different keypad types (see "Compatible devices" on page 8);
however, all keypads have certain basic functionality in common.
Special keys
Scroll symbols < > on keypads with LCD displays indicate that options can be viewed by pressing the scroll keys. These
keys can also be used to position the cursor.
The [*] key is similar in function to the “Enter” key on a personal computer. It is generally used to accept the existing pro-
gramming option. It is also the first key entry for [*] commands and can be used to enter the letters A-F when in Installer Pro-
gramming mode.
The [#] key is similar in function to the “ESC” (escape) key on a personal computer. It is generally used to exit the current pro-
gramming section or to return to the previous one.
LED indicators
Keypads have the following status lights that provide visual indication of basic system status:
Ready: Panel is ready to be armed.
Armed: Panel is armed.
Trouble: System trouble. Enter [*][2] to view troubles.
AC Power: ON=AC present. OFF=AC absent.
Panel status LED operation

The red status LED, located on the alarm controller PCB, indicates the following:
l Power up sequence – flashes rapidly until the end of the power-up sequence.
l Firmware indication – flashes during the firmware upgrade process. If the firmware upgrade fails, the LED flashes rap-
idly.
l Flashing cadences (timings) – During a firmware upgrade process the Status LED shall flash: 800ms on / 800ms off.
This cadence shall clear at the end of the firmware upgrade process. If the firmware upgrade fails the Status LED
shall flash: 200ms on / 200ms off. This cadence shall clear when the firmware upgrade process is reattempted.
- 44 -
l Trouble indication – Flashes when troubles are present. During normal operation the Status LED shall indicate
troubles using the following flashing pattern. No Trouble will be indicated by 120ms on / 10 sec off. Troubles will be
indicated by a number of flashes 400ms on / 400ms off (1.7 sec between flashes). Troubles with a lower number of
flashes shall be considered higher priority and will override the indication of lower priority troubles.
Troubles are indicated according to the following priority:
1 flash - no keypads enrolled
2 flashes - module supervision trouble
3 flashes - bus low voltage
4 flashes - low battery trouble
5 flashes - AC trouble
6 flashes - AUX trouble
7 flashes - bell trouble
8 flashes - TLM trouble
How to enter data
Conventions used in this manual
Brackets [ ] indicate numbers or symbols that must be entered on the keypad.
e.g., [*][8][Installer Code][804] requires the following key entries:
[*][8][5555][804]
[*] initiates a special command.
Note: [5555] is the default installer code. The default installer code should be changed during initial programming of the sys-
tem.
[804] indicates the particular programming section being accessed.
Entering letters manually (system labels)
1. In Installer Programming, enter the section requiring text input.
2. Use the arrow keys [<][>] to move the cursor to a blank space or existing character.
3. Press the number key corresponding to the appropriate letter. Each number button accesses three letters and a number.
The first press of the number key displays the first letter. The second press displays the second letter, etc.
1 2 3
A, B, C, 1 D, E, F, 2 G, H, I, 3
4 5 6
J, K, L, 4 M, N, O, 5 P, Q, R, 6
7 8 9
S, T, U, 7 V, W, X, 8 Y, Z, 9,0
0
Space
4. To select lower case letters press [*]. The Select Options list opens. Scroll to “lower case” and press [*] again to select.
5. When the required letter or number is displayed use the arrow keys [<][>] to scroll to the next letter.
6. When finished, press the [#] key to save the label and exit.
7. Continue from step 2 until all labels are programmed.
For information on entering hexadecimal data, see "Programming hex and decimal data" on page 74.
3.3 Enrollment
All optional modules and devices must be enrolled on the system. During enrollment, the electronic serial number (ESN) of
each device is identified to the control panel and zones are assigned. A wireless transceiver HSM2HOST or an RF keypad
must be enrolled first before wireless devices can be enrolled.
- 45 -
Enrolling modules
During automatic and manual enrollment, if an attempt is made to enroll more than the maximum number of modules, an
error tone sounds and a message is displayed on LCD keypads.
Modules can be enrolled automatically or manually using section [902] of Installer programming. For instructions on
enrolling modules, see "Module Programming" on page 149
To confirm that a module has been successfully enrolled, use Installer programming section [903]. See "[903] Confirm Mod-
ule" on page 150.
Enrolling the first keypad
To enroll a hardwired keypad, connect the keypad to the alarm controller, power up the alarm panel then press any button
on the keypad.
To enroll a wireless keypad, first connect the HSM2HOSTx wireless integration module to the alarm controller. Next, power
up the alarm panel and a wireless keypad. Press any button on the keypad to enroll it on the HSM2HOSTx. The
HSM2HOSTx is then enrolled on the alarm panel. To enroll other keypads, see "Module Programming" on page 149.
Module supervision
By default, all modules are supervised upon installation. Supervision is enabled at all times so that the panel can indicate a
trouble if a module is removed from the system.
To check which modules are currently connected and supervised, see "[903] Confirm Module" on page 150.
If a module is connected but is not recognized by the system, it may be due to any of the following reasons:
l the module is incorrectly wired to the alarm controller
l the module has exceeded its maximum wire run length
l the module does not have enough power
Removing modules
Enrolled modules can be deleted from the system via programming section [902]. For instructions, see "[902] Add/Remove
Modules" on page 149.
Enroll wireless devices

Wireless devices are enrolled via the wireless transceiver module and Installer Programming section [804][000]. See "Com-
patible devices" on page 8 for a list of supported wireless devices.
Wireless devices are enrolled using one of the following methods:
Auto enrollment
To enroll a wireless device using this method, press and hold the Enroll button on the device for 2-5 seconds until the LED
lights then release the button. The alarm panel automatically recognizes the device and the keypad displays a confirmation
message. The device ID and next available zone number are displayed. Press [*] to accept or scroll to another available
zone number. Batteries must be installed in the wireless device in order to enroll.
Various zone features are programmable depending on the type of device. See "Zone setup" on page 78 for details.
Pre-enrollment
Pre-enrollment is a two step process. The first step requires entering each device ID ([804][001]-[716]). Every wireless device
has an ID printed on the sticker attached to the device. The format is XXX-YYYY where:
l XXX identifies the type or model of the device
l YYYY is a short encrypted ID used by the system to identify the specific device
Pre-enrollment can be done at a remote location and using DLS/SA. The second step is to press the enrollment button on
the device, usually done on location. Installer Programming does not have to be entered at this step. Both steps must be per-
formed in order to complete the enrollment.
- 46 -
3.4 Working with partitions

A partition is a limited area of the premises that operates independently from the other areas. Partitioning a system can be
beneficial if the property has outbuildings that need to be secured independently of a main area.
Each partition can have its own keypad or a keypad can have access to all partitions (only if all partitions belong to the same
user code). User access to partitions is controlled via access codes. A master code can access the entire system and all par-
titions, while a user code is limited to assigned partitions.
Setting up a partition requires the following actions:
l Create the partition.
l Define bell/siren operation.
l Assign keypads.
l Assign zones.
l Assign users.
Setting up a partition
Partitions are added or removed from the system by applying or removing a partition mask via Installer programming section
[200]. The number of available partitions depends on the alarm panel model. See "[200] Partition Mask" on page 114 for
more information.
Bell/siren operation
Each partition must have a siren. The system siren connected to the bell output of the alarm controller can be mounted in a
central location within hearing range of all partitions. Each partition can also have wireless sirens activated only on the
assigned partition. See "Wireless Programming" on page 132 for details.
Single siren output operation
With a siren shared across all partitions, control over activation/deactivation of the output depends on the partition that ini-
tiated the alarm sequence. Only the partition that originated the alarm can deactivate the bell output.
Global zones, such as smoke detectors shared by multiple partitions, can deactivate the siren on all partitions the zone is
assigned to.
Multiple siren output operation
When multiple sirens are used in the installation, they can be programmed to sound alarm conditions for all partitions, or for
individual partitions by using a partition enable mask.
If hardwired sirens are used, this is accomplished via bus power supplies with a supervised high-current output. The output
is then programmed as a Fire and Burglary PGM output type.
Note: Only the first output of the HSM2204 output module has bell supervision. Some conditions, such as an installer system
test, may override the partition assignment and cause all sirens to activate. User system tests only activate the sirens/outputs
assigned to that partition.
Interconnected smoke detector operation

When the Fire Alarm toggle is enabled ([804][001]-[248] option 14) on a zone with a PowerG smoke detector, any fire alarm
on a partition assigned to the detector activates the sounder. Global fire alarms activate the sounder on all smoke detect-
ors.The sounder on interconnected smoke detectors follows the panel bell for duration of activation ([014] option 8, Fire Bell
Timeout). If this option is disabled, interconnected smoke detectors continue to sound the alarm until the bell is deactivated
on the panel.
The following alarm types cause interconnected smoke alarms to sound:
- Fire zones
- [F] key alarms
- 2 Wire smoke input
- 47 -
3.5 Trouble indicators

Both audible and visual trouble indications are available on all partitions. For more information, see "Troubleshooting" on
page 59
Programming section [013] option 3 controls whether or not troubles are indicated when the alarm system is armed.
3.6 Keypad partition setup

Keypads can be configured to control an individual partition or all partitions. In general, a partition keypad controls the par-
tition it is assigned to. A Global keypad controls all partitions. Global keypads should be placed in common areas of the
premises, such as points of entry or reception areas, where the ability to arm and disarm more than one partition at a time is
required.
Partition keypads can also be temporarily loaned to other partitions.
To select a keypad operating mode:
1. Enter Installer Programming: [*][8][installer code].
2. Select [861]-[876] to program keypads 1-16.
l Press [000] for partition assignment.
l For Global operation, key in 00.
l To assign a keypad to a partition, key in 01-08 for partition 1-8.
3. Press the [#] key and repeat step 2 for next keypad. When finished programming all keypads, press the [#] key twice to
exit programming.
Users are assigned partition access rights via the [*][5] menu.
Loaned partition setup

To loan a keypad to another partition:
1. Press and hold [#] then key in a valid access code. The keypad switches to Global display.
2. Use the arrow keys to scroll through available partitions. Press [*] to select. The keypad is temporarily loaned to another
partition.
If the keypad is inactive for more than 30 seconds, it reverts to its assigned partition.
Global zones
If a zone is added to more than one partition, it becomes a global zone. A global zone is only armed when all assigned par-
titions are armed and is disarmed when any assigned partition is disarmed.
Global zones behave as follows:
l A global Stay/Away type zone is not activated until all partitions the zone is assigned to are armed in the Away mode.
Interiors must be activated on all partitions for the global Stay/Away zone to be active.
l A shared zone bypassed on one partition is bypassed on all partitions the zone is assigned to.
l An entry delay started on a global zone sounds an entry delay on all keypads assigned to partitions the global zone
is assigned to.
l A global Delay type zone follows the longest programmed delay time of the partitions it is assigned to.
Fire and CO zone types

Fire zones only place the partition they are assigned to into alarm. Other partitions retain their current state.
A fire reset only resets partitions they are assigned to.
One or more fire zones may be located on any partition.
On alarm, the fire auto-scroll display appears on all partition keypads and on all global keypads. Fire alarm silence and fire
system reset may be done directly on any partition keypad. To silence a fire or CO alarm from a global keypad requires that
the global keypad be loaned to one of the partitions the zone is assigned to.
- 48 -
Bell/PGM support
PGMs must be assigned to one or more partitions. See section [007] for partition assignment.
Note: Bell PGM type requires supervision and follows arming squawks by partition.
Communications
Account codes are assigned to all system and partition events.
For SIA communications, a single account code (programmed in section [310][000]) is used for all events. The partition is
identified via Nri1-8. System events use Nri0.
When using CID communication, individual account codes must be programmed for each partition. See "[310] Account
Codes" on page 122.
Assign zones
Partition zone assignments are completed using sections [201] - [208] for partitions 1 - 8. Subsections [001 - 016] are then
used to enable or disable banks of 8 zones on the partition.
Assign users
Access [*][5] using the master code, select the desired user code and enter digit 4 to modify the partitions that can accept the
user code.
Factory defaults
Individual modules, as well as the alarm panel itself, can have their programming returned to factory default settings. Hard-
ware is defaulted via the following Installer Programming sections:
l [991] Default Keypads
l 000 – Default all keypad programming
l 001-016 – Default keypads 1-8
l [996] Default wireless receiver
l [998] Default HSM2955
l [999] Default system
See "Defaults" on page 152 for more information.
Default all labels
Use programming section [000][999]. The following labels are returned to factory default settings:
l Zone Label
l Partition Labels
l Module Labels
l Partition 1-8 Command Output 1 to 4 Labels
l Schedule 1 to 4 Labels
l Event Labels
l User Labels
System and module programming is not affected.
Hardware reset main control panel
Perform the following to restore the main control panel to default settings:
1. Power down the system.
2. Remove all wires between Zone 1 and PGM 1 on the alarm controller.
3. Connect a short between Zone 1 and PGM 1.
4. Power up the system for 60 seconds.
5. Power down the system and remove the short.
6. Power up the system again. Factory defaults are restored and hardware default is logged to the event buffer.
Note: Hardware default is not available when installers lockout is enabled.
- 49 -
3.7 Alternate communicator setup

The alternate communicator is an ethernet or optional cellular communications device that can be used as a backup to the
PSTN connection or as a primary means of communication between the alarm panel and the central monitoring station. The
alternate communicator communicates via 2G, 3G, LTE or Ethernet.
The following configuration steps are required to set up the alternate communicator:
l Install the optional cellular alternate communicator to the alarm panel
l Enroll the alternate cellular communicator with Connect 24 (North America only)
l Set the communication path: [300]
l Enable the alternate communicator: [383] option 3 for Ethernet, and [383] option 4 for cellular.
l The Ethernet or Cellular receivers IP and Port: [851]
l Enable event reporting: [307]/[308]
l Program communication delay timer: [377]
l Program DLS access: [401] option 07
Refer to Section 5: Programming for details.
Communication paths
The path of communication between the alarm panel and the central station must be established through either the alarm
panel’s on-board Public Switched Telephone Network (PSTN) connection (Ethernet) or through the alternate communicator
if equipped.
Communications options
The following alarm panel options must be programmed when configuring the alternate communicator:
[300] option 02: communication path (see "[300] Panel/Receiver Communication Paths " on page 115)
[380] option 01: communications enabled/disabled (see "[380] Communicator Option 1" on page 125)
[383] option 03: ethernet communications enabled/disabled, [383] option 04: cellular communications enabled/disabled
[308][351]-[356] reporting codes (see "[351] Alternate Communicator 1")
[401] option 7: DLS access (see "[401] System Test Events")
Communication attempt limit

If a telephone line monitoring (TLM) trouble is present, the number of PSTN dialing attempts is reduced from the pro-
grammed value to 0 attempts. See programming section [380] Communicator Option 1 for details.
Supervision restore
If the alarm system experiences a failure to communicate (FTC) with the central monitoring station, it automatically attempts
to transmit the failed event when communications are restored when [383], option 5 is enabled.
Remote firmware upgrade

Firmware upgrades can be transferred to the alarm panel and modules using DLS. A message is displayed on LCD keypads
indicating a firmware upgrade is available. On all keypads, the blue light bar flashes.
Users authorize the firmware upgrade through [*][6][Master Code][17].
During the update, a message indicating that a firmware upgrade is in progress is displayed on the LCD keypad.
Firmware updates are performed under the following conditions:
l The system is not armed
l No AC trouble is present
l No low battery trouble is present
Note: For UL listed installations, do not use remote programming unless an installer is on the premises.
- 50 -
3.8 Local firmware upgrade

Alarm panel firmware can be upgraded locally via DLS. Firmware upgrade prevention rules are ignored when performing a
local firmware upgrade.
To perform a local firmware upgrade:
1. Remove the front cover of the alarm panel and plug the DLS header into the micro USB connector on the alarm con-
troller.
2. Open the Flash Utility within DLS, select the latest firmware file from the Web or browse to a saved flash file on your hard
drive. Follow the steps as prompted by the Flash Utility application. A message is displayed when download is complete.
3. Once the firmware update is complete, the system powers up.
3.9 Testing the system

Installer Walk Test
Walk test enables the installer to test the operation of each detector by tripping zones, causing an actual alarm. Enter section
[901] to initiate a walk test. When a zone is tripped, all system sirens emit a tone to indicate that the zone is working correctly.
After 15 minutes without zone activity, the walk test terminates automatically. To manually exit walk test mode, enter [901]
again.
Viewing the event buffer

The event buffer contains logs of events that have occurred on the alarm system beginning with the most recent. The capa-
city of the event buffer is scalable and can hold 500/1000 events (depending on panel model) before rolling over. The buffer
displays events according to their time stamp, beginning with the most recent. The event buffer can be uploaded using DLS.
Each event displays the time and date, a description of the event, the zone label, access code number or any other pertinent
information. To view the event buffer, press [*][6][Master Code][*].
- 51 -
Section 4: System operation

4.1 Arming and disarming
The following table describes the various arming and disarming methods available.
Table 4-1 Arming/disarming methods
Method Description
Away Arm for 2 seconds + [Access Code*]
Stay Arm for 2 seconds + [Access Code*]
Night Arm when armed in stay mode [*][1] + [Access Code*]

Disarm [Access Code]
No-Entry Arming [*][9] + [Access Code]
Quick Arm/Quick Exit [*][0] Note: this feature shall not be used in EN50131 certified systems.
* - requiring an access code can be programmed in Section [015]

For detailed arming/disarming instructions, see the PowerSeries Pro User Manual.
4.2 Partition vs. global keypad

Keypads can be configured to control an individual partition or all partitions (see "Keypad partition setup " on page 48).
Single partition operation

Single partition keypads provide access to alarm functionality for an assigned partition.
Single partition keypads behave as follows:
l Display the armed state of the partition
l Display open zones, if the zone belongs to the partition the keypad is assigned to
l Display bypassed zones and allow zone bypassing or creating bypass groups of zones assigned to the keypad par-
tition
l Display system troubles (system low battery, system component faults/tampers)
l Display alarms in memory that occurred on the partition
l Allow the door chime to be enabled/disabled
l Activate system test (sounds bells/PGMs assigned to the partition)
l Allow label programming (user labels for the partition)
l Control command outputs (those assigned to the partition, or global outputs such as smoke detector reset)
l Display temperature (not evaluated by UL)
Global/multiple partition operation

Global keypads display a list of all active partitions or assigned partitions along with their current state. A valid access code
is required to view partition status. The Global status screen displays the following:
1 2 3 4 5 6 7 8
R A ! N X E P -
R = Ready X = Exit Delay
A = Armed E = Entry Delay
! = Alarm P = Pre-Alert
N = Not Ready - = Partition not enabled
- 52 -
In the following example, partition 1 is armed, partition 2 is disarmed and ready, partition 3 is disarmed and not ready, par-
tition 4 is in alarm, partition 5 is indicating exit delay, partition 6 is in entry delay, partition 7 is in auto-arm pre-alert and par-
tition 8 is not enabled.
1 2 3 4 5 6 7 8
A R N ! X E P -
Global keypads behave as follows:
l Troubles are displayed and sounded on the global keypad. Troubles can be viewed from the global keypad display
by pressing the right scroll key then (*). The Troubles menu is displayed. An access code may be required to enter
the [*][2] menu depending on system programming.
l Keypad function keys can be programmed for Global Stay Arm, Global Away Arm and Global Disarm.
l Multiple partition arming/disarming may be done from a global keypad, assigned to the same partitions as the user,
by scrolling right and selecting "[*] to Arm All Partitions.
4.3 Labels
Various custom labels can be created to make identification of the alarm system, partitions, zones and modules simpler.
Labels are created by inputting text manually, by selecting words from the Word Library or by downloading/uploading using
DLS. See "[000] Label Programming" on page 75
System label
This feature is used to program a custom label for the security system. This label is used in the event buffer when system
events occur. The maximum label size is 14 ASCII characters.
See "[100] System label" on page 77for programming details.
Zone labels
Customized labels can be created for each zone on the alarm system. These labels are used on various displays and events
to identify the zone. The maximum label size is 14 x 2 ASCII characters.
See "[001]-[248] Zone Labels" on page 75 for more details.
Partition labels
Each partition on the alarm system can have a unique label to identify it. This label is displayed on partition keypads and
event messages. The maximum label size is 14 x 2 ASCII characters.
See "[101]-[108] Partition 1-8 labels" on page 77 for more details.
Module labels
Labels can be created for the following optional system modules:
l keypads
l 8 zone expander modules
l 8 output expander modules
l wireless transceiver
l power supply
l 4 high-current output module
l alternate communicator module
l audio module
l siren
l repeater
The maximum label size is 14 ASCII characters.
See "[801] Keypad labels" on page 77 for more details.
Event labels
Customizable labels can be created for the following events:
- 53 -
l Fire alarm
l Fail to arm
l Alarm when armed
l CO alarm
The maximum label size is 14 ASCII characters.
Partition command output labels

This feature is used to program custom labels for command outputs. These labels are used with output activation events in
the event buffer. The maximum label size is 14 x 2 ASCII characters. See "[201]-[208][001]-[004] Partition command output
labels" on page 77 for more details.
4.4 Annunciation
Door chime
The keypad can be programmed to use one of four different door chime tones for each zone on the system. Chime is active
only during the disarm state. Only one door chime option can be enabled for each zone.
l Beeps
l Bing-Bong
l Ding-Dong
l Alarm Tone
l Zone Name - Voice Annunciation (HS2LCDWFVPROx keypads only)
The above door chime sounds are programmable in section [861]-[876], subsections [101]-[228].
Chime is enabled/disabled on a partition using the [*][4] command.
Temperature display
Indoor and outdoor temperature can be displayed on system keypads if configured in keypad programming section [861]-
[876]>[023] option 7, and sections [041]-[042]. Temperature is detected using wireless temperature sensors installed on the
system. Refer to "Compatible devices" on page 8.
Global keypads only display outdoor temperature.
Low temperature warning

Keypads can be configured to detect low ambient temperature.
If the temperature at the keypad drops to 6° C ± 2° C (43° F ± 3°F), the keypad zone goes into alarm. When the temperature
rises above 9° C ± 2° C (48° F ± 3° F), the keypad zone is restored.
When this option is enabled, the keypad’s zone input functionality is disabled.
Refer to section [861]-[876]>[023] option 8 for more information.
Note: This feature has not been evaluated by UL/ULC.
- 54 -
4.5 Keypad function keys

Keypads have 5 programmable function keys that can be configured to perform one of the following actions:
Table 4-2 Function key programming options
[00] Null Function Key [17] Arm Interior
[02] Instant Stay Arm [21]-[24] Command Output 1 to 4[*][71] - [*][74]
[03] Stay Arm [29] Bypass Group Recall
[04] Away Arm [31] Local PGM Activate
[05] [*][9] No-Entry Arm [32] Bypass Mode
[06] [*][4] Chime On/Off [33] Bypass Recall
[07] System Test [34] User Programming [*][5]
[09] Night Arm [35] User Functions [*][6]
[12] Global Stay Arm [37] Time & Date Program
[13] Global Away Arm [39] Trouble Display [*][2]
[14] Global Disarming [40] Alarm Memory [*][3]
[15] Temperature [61]-[68] Partition 1 to 8 Select
[16] Quick Exit
To program a function key:

1. Enter Installer Programming [*][8].
2. Enter section [861] for keypad 1 function key programming.
3. Enter [001] to [005] to select a function key to program.
4. Enter a 2-digit number to assign a function key operation - [00] - [68]. See table above.
5. Continue from step 3 until all function keys are programmed.
6. Press the [#] key twice to exit Installer Programming.
Programmed function keys must be pressed for 2 seconds in order to activate the function.
Function key definitions

This section provides detailed descriptions of each programmable function key option.
[00] Null Function Key
This option deactivates the function key. The key does not perform any function when pressed.
[02] Instant Stay Arm
This feature is similar to the Stay Arm function key, except that no exit delay is applied and the system arms immediately.
If no Stay/Away zone types are programmed, the alarm system arms in Away mode.
Note: Do not use this function with CP-01 installations.
[03] Stay Arm
Only perimeter zones are armed. Interior zones are bypassed regardless of whether or not delay zones are tripped during
the exit delay.
[04] Away Arm
All interior and perimeter zones are armed. CP-01 panels require an exit through a delay zone during the exit delay or the
system will arm the perimeter zones only.
[05] No-Entry Arm [*][9]
All Delay 1 and Delay 2 zones become instant zones. If a door or window is opened the system goes immediately into alarm.
This function is typically used when no occupants are expected to return to the site during the armed period. Activation of this
function key requires an access code. This function only works while the system is disarmed.
See "[*][9] no-entry arming" on page 70 for more information.
- 55 -
[06] Chime On/Off

This function turns the door chime on or off and is the equivalent of pressing [*][4]. The alarm system must be disarmed to
use this function. If option 7 in section [023] is enabled, this function key requires an access code.
[07] System Test
This function performs a system test when pressed and is the equivalent of entering [*][6][Access Code][04]. The alarm sys-
tem must be disarmed to use this function. See "[*][6] user functions" on page 67 for more information.
[09] Night Arm
All perimeter and interior zones, excluding Night zones, are armed. This key only works while the system is disarmed or
armed in Stay mode.
If no Night type zones are programmed, the alarm system arms in Away mode with an audible exit delay. Exit delay is silent.
Arming in this mode activates the Away Arming PGM output.
[12] Global Stay Arm
This function arms all partitions assigned to the user in Stay mode, provided they are ready to arm. If a partition is not ready,
the system cannot be armed. An access code is required with this option.
[13] Global Away Arm
This function arms all partitions assigned to the user in Away mode, provided they are ready to arm. If a partition is not ready,
the system cannot be armed. An access code is required with this option.
[14] Global Disarming
This function disarms all partitions assigned to the user. An access code is required with this option.
[15] Temperature
This function allows the keypad to directly access the temperature display menu.
[16] Quick Exit
Pushing this key gives the user a 2 minute window to open and close one delay zone once without having to disarm the sys-
tem. This function is equivalent to entering [*][0] at the keypad while the partition is armed. If quick exit is not enabled on the
system, or if the system is disarmed, pressing this key causes an error tone. An access code is not required to use this key.
See "[015] System Option 3" on page 103 for more information.
[17] Arm Interior
This key removes or enables automatic bypass on all Stay/Away zones (equivalent to pressing [*][1] while armed).
If this function is performed while stay armed and, Night zones are programmed, the system arms in Night mode. If no Night
zones are programmed, the system arms in Away mode. If armed in Night or Away mode, this key switches the system back
to Stay mode. Pressing this key does not switch the arming mode from Night to Away.
This key only works while the system is armed and requires an access code entry if section [015] option 4 is disabled.
[21]-[24] Command Output 1 to 4
This function controls command outputs 1-4 and is the equivalent of entering [*][7][X], where X is 1, 3 or 4.
An access code is required to use this function.
Selecting command output 2 is the equivalent of pressing [*][7][2] sensor reset. See "103 – Sensor Reset [*][7][2]" on page 88
for more information.
[29] Bypass Group Recall
This function bypasses all zones belonging to the bypass group.
Zones must be saved in the bypass group for this function key to operate. An access code is required to use this feature if
section [023] option 4 is enabled.
Note: Do not use with wireless keys.
[31] Local PGM Activate
This function controls a PGM connected to a keypad.
[32] Bypass Mode
This function places the keypad in Zone Bypass mode. Selecting this function is the equivalent of pressing [*][1] while dis-
armed. If an access code is required for bypassing, the user must enter the access code before using this function. An
access code is required if section [023] option 4 is enabled.
- 56 -
[33] Bypass Recall

This function bypasses the same set of zones that were bypassed the last time the partition was armed. This function is equi-
valent to pressing [999] while in the [*][1] menu. An access code is required to use this feature if section [023] option 4 is
enabled.
[34] User Programming
This function is the equivalent of entering [*][5]. A master or supervisor access code is required to use this function. This key
only works while the system is disarmed.
[35] User Functions
This function puts the keypad in user programming mode and is the equivalent of entering [*][6]. An access code is required
to use this function. If section [023] option 8 is off, only the Master or Supervisor code can access the [*][6] menu.
[37] Time & Date Program
This function places the keypad in date/time programming mode. A valid access code is required.
[39] Trouble Display
This function puts the keypad in trouble display mode and is equivalent to pressing [*][2]. This function only works while the
system is disarmed. This function key requires a code if section [023] option 5 is enabled.
[40] Alarm Memory
This function puts the keypad in alarm memory display mode and is equivalent to pressing [*][3]. This function only works
while the system is disarmed. This function key requires a code if section [023] option 6 is enabled.
[61]-[68] Partition 1 to 8 Select
This function selects partition 1-8 when the assigned key is pressed. Pressing and holding the key for 2 seconds selects the
next partition.
4.6 Language selection

The keypad can be programmed to display messages and labels in different languages. Perform the following from the
Installer Programming menu:
1. Enter installer programming [*][8][installer code]
2. Enter section [000]>[000].
3. Select a language using the scroll buttons or by entering a hotkey:
Table 4-3 Languages
[01] – English [15] – Greek
[02] – Spanish [16] – Turkish
[03] – Portuguese [18] – Croatian
[04] – French [19] – Hungarian
[05] – Italian [20] – Romanian
[06] – Dutch [21] – Russian
[07] – Polish [22] – Bulgarian
[08] – Czech [23] – Latvian
[09] – Finish [24] – Lithuanian
[10] – German [25] – Ukrainian
[11] – Swedish [26] – Slovakian
[12] – Norwegian [27] – Serbian
[13] – Danish [28] – Estonian
[14] – Hebrew [29] – Slovenian
4. Press [#] to exit.

5. After changing the language, a label default needs to be performed. [000] [999].
- 57 -
Note: Ensure the LCD keypad supports the desired languages.
4.7 [*] Commands

[*] commands provide convenient access to alarm system features. The following commands are available:
[*][*] Temperature function
[*][1] Bypass zones
[*][2] View troubles
[*][3] View alarms in memory
[*][4] Door chime on/off
[*][5] User programming
[*][6] User functions
[*][7] Command output 1-4 on/off
[*][8] Installer programming mode
[*][9] No entry arming
[*][0] Quick arm/Exit
While in a [*] command menu, use the [*] key to select an option and the [#] key to exit to the previous screen. On an LCD
keypad, use the scroll keys to view options.
[*][*] Temperature function

In this menu, wireless PG zones that have temperature reporting capabilities are shown. Scrolling through the menu shall
display the zone label for all the temperature capable zones on that partition. This feature can be programmed to require an
access code.
To enable temperature reporting on wireless PG devices it must be enabled via section [804][810] option 5. A function key
can also be programmed for this feature. See "[023] System Option 11" on page 110.
[*][1] Bypass or Stay/Away/Night zones

The [*][1] command functions differently depending on whether the system is armed or disarmed.
Note: For UL/ULC listed installations, group bypass is not allowed.
The zone attribute for zone bypassing must be enabled (see section [002] Zone Attributes, Option 04).
Holdup zones should not be part of bypass groups.
A zone that is manually bypassed via [*][1] will bypass the alarm, fault, and tamper conditions when DEOL is used.
If a 24-hour zone is bypassed, ensure that the zone is restored or disabled before removing the bypass.
When the alarm system is disarmed
Users can bypass individual zones or a programmed group of zones using the [*][1] keypad command. Zones are commonly
bypassed if users want to have access to an area while the partition is armed, or to bypass a defective zone (bad contact,
damaged wiring) until service can be provided. A bypassed zone does not cause an alarm.
When the partition is disarmed, all zones that were bypassed using [*][1] are no longer bypassed, except for 24-hr zones.
If the Code Required for Bypass option is enabled, an access code is required to enter bypass mode. Only access codes
with the Bypass attribute enabled can bypass zones (see "Access code attributes" on page 65).
Bypassing zones with an LCD keypad:
1. Ensure the system is disarmed.
2. Press [*] to enter the function menu. The keypad displays “Press [*] for < > Zone Bypass.”
3. Press [1] or [*], then key in your access code (if required).
4. Scroll to a zone or key in the three-digit zone number. Only zones enabled for zone bypassing are displayed. Enter the 3-
digit zone number or scroll to the desired zone and press [*] to bypass the zone.
- 58 -
“B” appears on the display to indicate the zone is bypassed. If a zone is open, “O” appears on the display. When an open
zone is bypassed, the “O” is replaced by “B.”
5. To clear a bypassed zone, repeat the above procedure. The “B” disappears from the display indicating that the zone is
no longer bypassed.
6. To exit bypass mode and return to the ready state, press [#].
Other bypass features:
The following features are also available on the [*][1] zone bypass menu:
Bypass Open Zones
Displays all currently open or bypassed zones. Use the scroll keys to view zones. Open zones are indicated by an (O). To
bypass a zone, press [*]. A bypassed zone is indicated by a (B).
Note: Zones with tampers or faults must be manually bypassed.
Note: This feature shall not be used for UL/ULC listed systems.
Bypass Group
Note: This feature shall not be used for UL/ULC listed systems.
Displays a programmed group of zones (bypass group) commonly bypassed. Press [*] to bypass all zones in the group.
Program Bypass Group
To program a bypass group, bypass all desired zones then select Bypass Options > Program Bypass Group. The selected
zones are saved to the bypass group. When finished, press [#] to exit.
In order to program a bypass group, a master or supervisor code with access to the appropriate partition must be used.
Bypass Recall
Press [*] while in this menu to bypass the same group of zones that were bypassed the last time the partition was armed.
Clear Bypasses
Press [*] to clear all bypasses.
Shortcuts from the [*][1] base menu:
991 = bypass group
995 = program group 1
998 = bypass open zones
999 = bypass recall
000 = clear group
When the alarm system is armed
When the system is armed, pressing [*][1] toggles between stay, away or night arming. If a night zone is on the system, press-
ing [*][1] either prompts the user for an access code if required, or sounds an acknowledgment tone and changes the arming
mode.
Note: If section [022], Option 5 [Stay/Away Toggle] is on, the system does not change from Away to Stay mode.
Troubleshooting
LCD programmable-message keypad:
l Press [*][2] followed by access code if required to view a trouble condition
l The trouble light flashes and the LCD displays the first trouble condition
l Use the arrow keys to scroll through all trouble conditions present on the system
Note: When additional information is available for a specific trouble condition, a [*] is displayed. Press the [*] key to view the
additional information.
[*][2] Trouble Display

This feature is used to view system troubles. If a trouble is present, the keypad Trouble indicator illuminates and an audible
indication is emitted (two short beeps every 10 seconds, except while in AC failure). Silence the audible indicator by press-
ing [#].
- 59 -
Troubles may be viewed while the system is armed or disarmed. The system may be programmed to show all troubles while
armed or only fire troubles. See section [13] option 3 for details.
The system can be configured to require a user code to view [*][2] system troubles. See section [023] option 5.
To view trouble conditions:
l Press [*][2] to enter the Trouble menu.
l On an LCD keypad, scroll to a trouble type then press [*] to view the specific trouble. The zone name and trouble con-
dition for each trouble are displayed on the screen.
Note: The trouble beeps generated by fire trouble are only silenced after [*][2]trouble menu is exited. A keypress in the
keypad will not silence the fire trouble beeps. For UL installations, set the value in section [023] bit 5 access code required
for [*][2] to enabled.
Table 4-4 : Trouble Indications
Trouble 01 – Service Required:
[01] Bell Circuit Trouble: The bell circuit is open
[02] RF Jam: The HSM2HOSTx has detected an RF Jam condition
[03] Loss of Clock: System time and date require programming.
[04] Output 1 Fault: An HSM2204 module has detected an open condition on output #1.
[05] Warm Start: Warm restart has occured.
[06] USB Wi-Fi Connected: USB Wi-Fi adapter is detected
[07] Power Unit Failure (System): Failure detected with internal power unit.
[08] Failure detected with internal power unit (HSM3204CX Corbus Repeater)
[09] Failure detected with internal power unit (HSM3350 3 A Power Supply)
[10] Overcurrent Trouble: If the total current of the panel internal components and all outputs exceeds a threshold of 2.1 A for a period longer
than 5 minutes, an overcurrent trouble is generated. When the current goes below a 2.0 A threshold, the trouble restores. Do not exceed 2A
combined between AUX and Corbus.
Note: Total current does not include bell current or battery charging.
Trouble 02 – Battery Trouble:
[01] Panel Low Battery Trouble: The battery voltage is low.
[02] Panel No Battery: No battery connected to alarm controller.
[04] HSM2204 01 - 04 Low Battery: An HSM2204 has a low battery voltage.
[05] HSM2204 01 - 04 No Battery: No battery connected to HSM2204.
[07] HSM2300 01 - 04 Low Battery: An HSM2300 has a low low battery voltage.
[08] HSM2300 01 - 04 No Battery: No battery connected to HSM2300.
[10] HSM3204CX Low Battery: A Corbus repeater has a low battery voltage.
[11] HSM3204CX No Battery: No battery connected to corbus repeater.
[13] HSM3350 Low Battery 1: A 3 A power supply module has a low battery voltage.
[14] HSM3350 Low Battery 2: A 3 A power supply module has a low battery voltage.
[15] HSM3350 No Battery 1: No battery connected to 3A power supply module.
[16] HSM3350 No Battery 2: No battery connected to 3A power supply module.
- 60 -
Trouble 03 – Bus Voltage:

[01] HSM2HOSTx Bus Low Voltage: The HSM2HOSTx module has measured a low bus voltage.
[02] Keypad 01 - 16 Bus Low Voltage: A hardwired keypad has a low bus voltage.
[04] HSM2108 01 - 30 Bus Low Voltage: A zone expander has a low bus voltage.
[05] HSM2300 01 - 04 Bus Low Voltage: A power supply has a low bus voltage.
[06] HSM2204 01 - 04 Bus Low Voltage: A high current output module has a low bus voltage.
[07] Bus Fault (System): Panel Corbus Output voltage is too hight or too low.
[08] HSM2208 01 - 16 Bus Low Voltage: The low current output module has detected a low voltage.
[09] HSM2955 Bus Low Voltage: The audio module has detected a low bus voltage.
[10] HSM3408 Bus Low Voltage: The 8 zone expander has detected a low bus voltage.
[11] HSM3204CX Bus Low Voltage: The corbus repeater has detected a low bus voltage.
[12] HSM3204CX Bus Fault: The corbus repeater has detected that the corbus output voltage is too high or too low.
[13] HSM3350 Bus Low Voltage: The 3 A power supply module has detected a low bus voltage.
Trouble 04 – AC or DC input power trouble:
[01] Zone 001 - 248 AC or DC input power trouble.
[02] Keypad AC or DC input power trouble: A keypad has an AC or DC input power trouble.
[03] Siren 01 - 16 AC: A siren has an AC or DC input power trouble.
[04] Repeater 01 - 08 AC: A wireless repeater has an AC or DC input power trouble.
[05] HSM2300 01 - 04 AC: An HSM2300 has an AC or DC input power trouble.
[06] HSM2204 01 - 04 AC: An HSM2204 has an AC or DC input power trouble.
[07] Panel AC: The alarm controller has an AC failure condition.
[08] HSM3204CX AC: A corbus repeater has an AC or DC input power trouble.
[09] HSM3350 AC: The 3A power supply has an AC or DC input power trouble.
Trouble 05 – Device Faults:
Note: Fire trouble is displayed directly under device faults when there is an open loop condition for PGM-2 configured for 2-wire smoke.
[01] Zone 001 - 248: A zone is in supervisory fault.
[02] Keypad 01 - 16: A wireless or hardwired keypad is in supervisory fault.
[03] Siren 01 - 16: A siren is in supervisory fault.
[04] Repeater 01 - 08: A wireless repeater is in fault (supervisory or loss of AC/DC).
[06] Device Mask: A detection mechanism on the sensor is masked.
[07] Gas Trouble:A gas sensor is in fault.
[08] Heat Trouble: A temperature sensor is in fault or a temperature reaches the high temperature warning threshold.
[09] CO Trouble: A CO sensor is in fault.
[10] Freeze Trouble: A temperature sensor falls below the low temperature warning threshold.
[11] Probe Disconn.: The probe on the flood detector or the temperature detector is disconnected.
[12] Fire Trouble: A smoke sensor is in fault.
Trouble 06 – Device Low Battery:
[01] Zone 001- 248: Wireless zone has a low battery.
[02] Keypad 01-16: Keypad has a low battery.
[03] Siren 01 - 16: Siren has a low battery.
[04] Repeater 01 - 08: Repeater has a low battery.
[05] User 01 - 1000: Wireless Key has a low battery.
- 61 -
Trouble 07 – Device Tampers:

[01] Zone 001 - 248 Tamper: A wireless or hardwired zone is in tamper.
[02] Siren 01 - 16 Tamper: A wireless siren is in tamper.
[03] Repeater 01 - 08 Tamper: A wireless repeater is in tamper.
[04] Audio Station 01 - 04 Tamper: An audio station connected to an HSM2955 is in tamper.
Trouble 08 – RF Delinquency Trouble:
[01] Zone 001 - 248 RF Delinquency: No response from a wireless zone for 13 minutes. This trouble prevents arming until acknowledged or
cleared using [*][2].
[02] Keypad 01 - 16 RF Delinquency: No response from a wireless keypad for 13 minutes.
[03] Siren 01 - 16 RF Delinquency: No response from a wireless siren for 13 minutes.
[04] Repeater 01 - 16 RF Delinquency: No response from a wireless repeater for 13 minutes.
Trouble 09 – Module Supervisory Trouble:
[01] HSM2HOSTx not responding.
[02] Keypad 01 - 16 not responding.
[04] HSM2108 01 - 30 not responding.
[09] HSM2955 is not responding.
[12] HSM3204CX is not responding.
Trouble 10 – Module Tamper:
[01] HSM2HOSTx Tamper.
[02] Keypad 01 - 16 Tamper.
[04] HSM2108 01 - 30 Tamper.
[05] HSM2300 01 - 04 Tamper.
[06] HSM2204 01 - 04 Tamper.
[08] HSM2208 01 - 16 Tamper.
[09] HSM2955 Tamper.
[10] Alt Comm Tamper.
[12] HSM3204CX Tamper.
Trouble 11 – Communications:
[01] TLM: Telephone line disconnected from control panel.
[02] Receiver 01-04 FTC Trouble: Failure to communicate using programmed receiver paths.
[04] Alt. Comm Cellular: Radio or SIM card failure, low signal strength detected, or cellular network fault.
[05] Alt. Comm Ethernet: Ethernet connection unavailable. A valid IP address is either not programmed or the module was unable to get an IP
with DHCP.
[06] Receiver 01-04 Trouble: Alternate communicator unable to initialize a receiver.
[07] Receiver 01-04 Supervision: Alternate communicator unable to communicate with a receiver.
[09] Alt. Comm Fault: The alternate communicator has stopped responding.
[10] Alt Comm FTC Trouble: The alternate communicator has failed to communicate an internal event not generated by the panel.
- 62 -
Trouble 12 – Not Networked Troubles:

[01] Zone 001-248 Not Networked: Generated when a zone becomes out of sync with the wireless network or has not been synchronized with
the network after enrollment.
[02] Keypad 01-16 Not Networked: Generated when a keypad becomes out of sync with the wireless network or has not been synchronized with
the network after enrollment.
[03] Siren 01-16 Not Networked: Generated when a siren becomes out of sync with the wireless network or has not been synchronized with the
network after enrollment.
[04] Repeater 01-08 Not Networked: Generated when a repeater becomes out of sync with the wireless network or has not been synchronized
with the network after enrollment.
[05] User 01 - 1000 Not Networked: Generated when a wireless key becomes out of sync with the wireless network or has not been
synchronized with the network after enrollment.
Trouble 13 – AUX Troubles
[05] HSM2300: 1 A power supply AUX output voltage is out of range.
[06] HSM2204: A high current AUX output module output voltage is out of range.
[07] System Area: AUX output voltage is out of range.
[10] HSM3408: The 8 zone expander AUX output voltage is out of range.
[11] HSM3204CX: The corbus repeater AUX output voltage is out of range.
[12] HSM3350 AUX 1 Trouble: 3 A power supply AUX output voltage is out of range.
[13] HSM3350 AUX 2 Trouble: 3 A power supply AUX output voltage is out of range.
Trouble 14 – Limit exceeded troubles
[01]Interactive zone: The number of zones configured in the panel is not supported by Alarm.com firmware (e.g:>220)
[02]Interactive partition: The number of partitions configured is not supported by Alarm.com firmware (e.g:>8)
IMPORTANT!
Ensure you have the following information available before contacting Customer Support :
l Alarm controller type and version, (e.g., HS3032, 1.0):
Note: Version number can be accessed by entering [*][Installer Code][900] on any keypad. This information is also located
on a sticker on the printed circuit board.
l List of modules connected to control panel, (e.g., HSM2108, HSM2HOSTx etc.).
[*][3] Alarm memory display

The Memory light flashes if an alarm, tamper or fault event occurred during the last armed period or while the panel was dis-
armed (24 hour zones). Press [*][3] to view zones in alarm memory. To clear the memory, arm and disarm the system. When
viewing alarms in memory, LCD keypads indicate the last zone that has gone into alarm first, followed by other alarms in
numerical order.
This feature can be programmed to require an access code. See "[023] System Option 11" on page 110, option 6 for details.
A programmable function key may be configured to display alarms in memory. See "Keypad function keys" on page 55 for
details.
[*][4] Door chime enable/disable

When this feature is enabled, the keypad emits a tone whenever a zone programmed as a Chime type is opened or closed.
Pressing [*][4] toggles between enabled and disabled. The door chime attribute for each zone is programmed in section
[002], subsections [001]-[248] option 4.
A function key can also be programmed to enable/disable this feature. See "Keypad function keys" on page 55 for details.
This feature may require an access code. See "[023] System Option 11" on page 110option 7 for details.
The following door chime sounds may be selected:
l 6 beeps
l "Bing-Bong"
l "Ding-Dong"
- 63 -
l Alarm tone
l Zone Name -Voice Annunciation (HS2LCDWFVPROx keypads only)
The above door chime sounds are programmable in section [861]-[876], subsections [101]-[228].
[*][5] Program access codes

Use this section to perform the following functions:
l press [1] to program user codes 0002-1000, and master code 0001
l press [2] to enroll a proximity tag
l press [3] to add a custom label for each user
l press [4] to assign users to partitions
l press [5] to program user attributes
Assign access codes
In order to access alarm system functionality, users must be added to the system. This involves creating a unique access
code and assigning attributes to each user. Access codes are programmed via the [*][5] menu.
Access code types
The alarm system provides the following access code types:
Code Add User Delete User Arm Disarm [*][5] [*][6] [*][8]
Installer No No No No No No Yes +
Master All* All Yes Yes Yes Yes No
Maintenance No No Yes Yes No No No
User No No Yes Yes No No** No
Supervisor All but Master All but Master Yes Yes Yes Yes No
Duress No No Yes Yes No No No
One-time use No No Yes 1/day No No No
+ If section [020] option 7 is on, a user must enter [*][6][Master Code][05] to give the installer permission to access pro-
gramming.
* Can only change master code if section [015] option 6 is off.
** Yes if [023] option 8 is on.
The Installer and Master codes are system codes. They can be changed but not deleted. The other codes are user-defined
and can be added or deleted as necessary. By default, access codes have the same partition and attribute programming as
the code used to program them.
Access codes are either 4, 6 or 8 digits in length, depending on the setting of programming section [041]. Duplicate codes
are not valid.
Note: EN50131-1 compliant systems using more than 100 access codes shall set the access code to 8 digits (section [041],
option 02).
Installer Code
This code provides access to Installer Programming [*][8]. The installer code is only used to gain access to configure the sys-
tem though [*][8] Installer Programming and does not have access to any other function. This code can be programed by the
installer in section [006][001]. The default is 5555 (4-digit), 555555 (6-digit) or 55555555 (8-digit).
EN Note: For EN50131-1 approved installations the installer code cannot change the master code or any other level 3 codes.
Attempting to access the master code from the installers code generates an error tone from the system.
Master Code - Access Code [0001]
By default the master code can access all partitions and can perform any keypad function. This code can be used to program
all access codes, including the supervisor and duress codes.
If section [015] option 6 is on, the master code can only be changed by the installer via Installer Programming.
The default is 1234 (4-digit), 123456 (6-digit) or 12345678 (8-digit).
- 64 -
EN The master code can be returned to factory default settings using Installer Programming section [989].
Maintenance Code
The maintenance code can only be used to arm and disarm the system. It cannot bypass zones. Use [*][9] to arm the system,
cancel auto-arming, or perform [*][7] command functions. No arm/disarm bell squawks are sounded when the maintenance
code is used. The Maintenance code can be programed by the installer in programming section [006][003]. The default is
AAAA (4-digit), AAAAAA (6-digit) or AAAAAAAA (8-digit).
User Codes - Access Codes [0002] to [1000]
This type of access code is used to arm and disarm assigned partitions and perform other functions as programmed. It can
access the [*][6] menu if programming option [023] option 8 is on. This code cannot access the [*][5] and [*][8] menus.
User access codes are created by the master user or supervisor users. The default is AAAA (4-digit), AAAAAA (6-digit) or
AAAAAAAA (8-digit).
Supervisor Codes - Access Codes [0002] to [1000]
A supervisor code is a user code with the Supervisor attribute enabled. Users with this attribute can access the [*][5] and [*]
[6] user code programming section for the partition they are assigned to. However, these codes can only program codes
which have equal or lesser attributes. These attributes are changeable via the [*][5] menu. A supervisor code is created by
the master user or other supervisor users.
Duress Codes - Access Codes [0002] to [1000]
Duress codes function the same as user access codes, except they transmit a duress reporting code when used to perform
any function on the system.
Duress codes cannot be used to access [*][5], [*][6] or [*][8] menus.
Duress codes are created by the master user or supervisor users.
Note: Section [019] option 6 must be on to select the Duress Codes attribute.
One Time Use Code
A one time use code is a user code with the One Time User attribute enabled. This access code enables the user to arm the
alarm system an unlimited number of times. However, a user with this code can only disarm the system once per day. The
ability to disarm is reset at midnight or when the one time user code is keyed in by the master code user.
Note: One time use code cannot be applied to wireless keys.
One time use codes are created by the master user or supervisor users.
To add an access code using an LCD keypad:
1. Press [*][5][master/supervisor code] to edit access codes 0002-1000.
2. Use the scroll keys to select a user then press [*] to edit.
3. On the “Press (*) for Access Code” menu, press [*]. The current access code is displayed.
4. Key in the new access code. The code is saved when the last number is keyed in.
To erase an access code, select the user number and enter [*] as the first digit. All digits of the access code must be
entered.
A “-” beside a user code indicates it is not programmed. A “P” indicates the code is programmed. A “T” indicates the code is
programmed and a proximity tag is enrolled.
Access code attributes
Each user code has 6 attributes that can be toggled on or off.
The default attributes of an access code are the same as the code used to enter [*][5], whether a new code is programmed or
an existing one is edited. The available attributes are as follows:
l Supervisor
l Duress code
l Zone bypassing
l Remote access
l Bell squawk
l One time use code
- 65 -
1 – Supervisor
Converts standard user into supervisor user. See "Access code types" on page 64 on page 58 for details.
2 – Duress Code
Converts standard user code into duress code. See "Access code types" on page 64 for details.
3 – Zone Bypassing
Users with this attribute can bypass zones. Section [023] option 4, Access code required for [*][1], must be on to use this
attribute.
7 – Bell Squawk
When this option is assigned, the main bell squawks when the alarm system is away armed. For example, use the arm/dis-
arm bell squawk attribute to have wireless key access codes squawk the bell, while other codes are silent. To do this, enable
this attribute on all access codes associated with wireless keys. This option is off by default for all access codes.
Note: One squawk indicates arming completed; two squawks indicates disarming completed.
Note: This feature is independent of the system option “Bell Squawk on Away Arming.” See "[017] System Option 5" on page
105
The master code's attributes cannot be changed from default. The bell squawk is off at default.
8 – One Time Use Code
Converts standard user code into one time use code. See "Access code types" on page 64 for details. Do not apply this code
to users with wireless keys assigned.
Using an LCD keypad:
1. Press [*][5][Master Code].
2. Use the scroll keys to choose a user (02-1000) then press [*] to select.
3. Scroll to “Press [*] for User Options” then press [*] to select.
4. Scroll to a user attribute and press [*] to toggle it on or off.
Add user labels
Custom labels can be programmed for each user to more easily identify them on the alarm system. Labels can be a max-
imum of 16 characters.
1. Press [*][5] then select a user (02-1000).
2. On the “Press [*] for User Labels” screen, press [*].
3. Key in the custom user label. For instructions on how to input labels, See "[000] Label Programming" on page 75
Assigning proximity tags
This section is used to assign proximity tags to users.
1. In the [*][5] menu, select a user or enter a user number.
2. Select “Press [*] for Prox Tag”, then pass the enrolled tag near the tag reader on the keypad. A proximity tag can only be
assigned to one user at a time.
To delete a proximity tag:
1. Select a user and then select Press [*] for Prox Tag.
2. Press the [*] key when prompted to delete the proximity tag.
To increase authentication flexibility, user access can be achieved by entering a valid user code or by swiping a proximity
tag. Alternatively, users can be required to enter a valid access code and present a proximity tag. See "[040] User Authentic-
ation" on page 112.
- 66 -
Assigning users to partitions

Each user code must be assigned to a partition(s) in order for the user to be recognized by the alarm system. By default,
each code has the attributes of the code used to program it.
1. Press [*][5][Master Code] then select a user (0002-1000). An “N” indicates they are not yet assigned to a partition. A “Y”
indicates they are assigned to a partition.
2. Scroll to the partition assignment screen then press [*].
3. Use the number keys to assign partitions.
4. Press [#] to exit.
Note: The master code has access to all partitions and cannot be modified.
User authentication options
The alarm panel can be configured to accept one of two user authentication methods:
1. User code or proximity tag - the user can access the system by entering a valid code or by presenting a proximity tag.
2. User code and proximity tag - the user must enter a valid code and present a proximity tag to access the system. The
user code and proximity tag must match. For example, if the tag is associated with user 0004, user code 0004 must be
entered after presenting the tag. Any other user code is treated as invalid.
See "[040] User Authentication" on page 112.
Note: An access code does not have to be programmed in order for a proximity tag or wireless key to be operational.
[*][6] user functions

The [*][6] command provides access to functions described below. If section [023] option 8 is on, any user code can access
this menu. If option 7 is off, only the master or supervisor code can access this menu.
Event Buffer
Menu: [*][6][Master Code] > Event Buffer
Keypad: [*][6][Master Code] > [*]
This option is used to view system events stored in the event buffer.
Events are listed in the order they occurred, starting with the most recent. The time and date are listed for all events. Some
events may have a second screen with a description. An asterisk (*) on the first screen indicates that a second screen is
available.
If programmed, the event buffer automatically uploads to DLS/SA when it reaches 75% capacity. See "DLS programming" on
page 73.
System Test
Menu: [*][6][Master Code] > System Test
Keypad: [*][6][Master Code] + 04
Select this option to test the alarm system's bell output, keypad buzzer and lights, communicator and standby battery.
Time and Date
Use this section to program the alarm system clock.
Menu: [*][6][Master Code] > Time and Date
Enter time and date using the following format: (HH:MM); (MM-DD-YY). Valid time entries are 00-23 hours, 00-59 minutes.
Valid date entries are 01-12 months, 01-31 days.
Other programming options that may affect this user function:
See "[901]/[902] – Daylight savings begin/end" on page 85.
Auto-Arm/Disarm
Menu: [*][6][Master Code] > Auto Arm/Disarm
- 67 -
With this feature enabled, the alarm system automatically arms in away mode (stay/away zones active) or disarms at a pro-
grammed time each day (see Auto-Arm Time below). The keypad emits three beeps to indicate the auto arming is enabled
and one long beep to indicate auto arming is disabled.
All arming inhibit features such as latching tampers, AC inhibit, etc. also inhibit Auto Arming and send the Auto Arm Can-
cellation code.
Auto-Arm Time
Menu: [*][6][Master Code] > Auto Arm Time
This function is used to program the time of day each alarm system partition automatically arms. To program an auto-arm
time, select a day of the week and then key in the time. Valid time entries are 00-23 hours: 00-59 minutes.
At the programmed time, the keypad buzzers beep for a programmed duration (for ULC commercial burglary installations
minimum duration is 10 minutes) to warn that automatic arming is in progress. The siren also squawks once every 10
seconds during this warning period if programmed to do so. When the warning period is complete, the system arms in away
mode.
Auto-arming can be canceled or postponed only by entering a valid access code during the programmed warning period.
When a code is entered, the warning is silenced and auto-arming is canceled or postponed, depending on the auto-arm
postpone timer. The Auto Arm Cancellation reporting code is transmitted (if programmed).
Note: Auto-arming will not silence an active bell.
Note: The Auto Arm Cancellation reporting code is also transmitted if arming is inhibited by one of the following:
l AC / DC Inhibit Arm
l Latching System Tampers
l Zone Expander Supervisory Fault
Other programming options that may affect this function:
See "[151]-[158] Partition Auto-Arm/Disarm" on page 113
See "[014] System Option 2" on page 102
Enable DLS/Allow System Service
Menu: [*][6][Master Code] > System Serv/DLS
This function enables and disables the DLS window for either 30 minutes or 6 hours depending on the programming of sec-
tion [025] option [7].
This function also enables the end user to provide or deny access to [*][8] Installer Programming. When enabled, the
installer can access Installer Programming either by DLS or via [*8] if a pre-programmed window has been set. After the win-
dow has expired, Installer Programming is unavailable again until the window is re-opened.
Note: DLS programming is not UL tested.
See "[020] System Option 8" on page 107 and see "[021] System Option 9" on page 109
See "[025] System Option 13" on page 112, bit "7 – DLS Window"
User Call-up
Menu: [*][6][Master Code] > User Call-up
When selected, this function makes a single attempt to call the downloading computer. The downloading computer must be
waiting for the call before downloading can be performed. Only one call-up is attempted. If a DLS phone number is not pro-
grammed, the alarm panel attempts to reach the DLS computer via IP connection. If the communicator is not properly con-
figured for IP, an error tone is sounded.
User Walk Test
Menu: [*][6][access code] > Walk Test
Keypad: [*][6][access code] + 08
- 68 -
Selecting this function places the alarm panel into user walk test mode. The Ready, Armed and Trouble LEDs on the keypad
flash to indicate that the test is active. If zones are tripped during a walk test, the system sounds a steady 2-second tone on
all keypads and the main bell to indicate that the zone is working correctly.
The walk test can be stopped at any time by re-entering [*][6][Master Code][08] on the keypad. The test automatically ter-
minates after 15 minutes of inactivity. An audible warning begins 5 minutes prior to automatic termination.
Note: Fire and CO alarms are not tested in user's walk test. If a fire or CO alarm is detected, walk test ends automatically and the
appropriate reporting codes are sent immediately to the monitoring station. Refer to the manufacturers instructions provided with
CO and Fire detectors for testing. This feature is not available in CP-01 systems.
Late to Open
Menu: [*][6][Master Code] > Late To Open
This function enables or disables the Late to Open option. This option sends a reporting code to the central monitoring sta-
tion if the partition has not been disarmed by a programmed time.
See "[201] Open/Close Events 1", option "[211] Miscellaneous Open/Close Events" on page 118.
Late to Open Time
Menu: [*][6][Master Code] > Late To Open Time
This function is used to program the time of day the partition must be disarmed by when the Late to Open option is enabled.
A separate time can be programmed for each day of the week. Valid data entries are 00:00 - 23:59. 99:99 disables the late to
open feature for the selected day.
Select a day of the week by scrolling while in the Late to Open menu, or by using keys 1-7 to select Sunday to Saturday
respectively.
Brightness Control
Menu: [*][6][Master Code] > Brightness Control
This function is used to change the brightness level of keypad display backlighting. Use the scroll keys to increase and
decrease brightness or enter a value from 00 to 15. Selecting 00 turns off keypad backlighting.
Contrast Control
Menu: [*][6][Master Code] > Contrast
This function is used to change the contrast level of keypad displays. Use the scroll keys to increase and decrease contrast
or enter a value from 00 to 15. Selecting 00 turns off keypad contrast.
Buzzer Control
Menu: [*][6][Master Code] > Buzzer Control
This function is used to change the volume level of keypad buzzers.
Use the scroll keys (LCD keypads) or the [*] key (LED/ICON keypads) to increase and decrease volume or key in a value
from 00 to 15. Selecting 00 turns off the keypad buzzer.
Note: For UL/ULC listed installations, do not turn off the keypad sounder.
Authorize Firmware Update
Menu: [*][6][Master Code] > Authorize Update
This function is used to give authorization to the system to start the firmware upgrade process after all firmware upgrade files
for the keypads, HSM2HOST and control panel have been fully downloaded.
Once this option is activated, the keypads and system automatically exit [*][6] and indicate that the firmware update is in pro-
gress.
Interactive Services
Menu: [*][6][Master Code] > Interactive Serv
- 69 -

This function is used by an alternate communicator to open the Interactive Services menu.
Priority Buffer
Menu: [*][6][Master Code] > Priority Buffer
This function logs priority events to a buffer, protecting them accidental or deliberate deletion, or alteration of its contents.
Alarm Buffer
Menu: [*][6][Master Code] > Alarm Buffer
This option is used to view system alarm events stored in the buffer.
Arming Buffer
Menu: [*][6][Master Code] > Arming Buffer
This option is used to view system arming events stored in the buffer.
[*][7] command outputs 1-4

Menu: [*][7][master code if required] > Output Control
Keypad: [*][7][master code if required]
This option is used to activate or deactivate command outputs 1 to 4 for each partition and enable command outputs to fol-
low a schedule.
1. Press [*][7] to enter Output Control mode.
2. Scroll to an output and press [*] to select it, or key in a command output number. The output is toggled on or off or can
activate for a fixed period of time.
3. Press [*][7][9] and enter the system master or supervisor code. Scroll to each command output and press [*] to enable or
disable the use of a programmed schedule to control the output.
Note: If no command outputs are programmed this function is not available. Other programming options that may affect this
user function:
See "121-124 – Command Outputs 1-4" on page 89
[*][8] installer programming

Use this option to place the alarm system in Installer Programming mode. Installer Programming is used to manually pro-
gram alarm panel and module options. An installer’s code is required to access this function.
Installer Programming is exited automatically after 20 minutes of inactivity.
When viewing data in sections with an LCD keypad, use the [<] and [>] keys to scroll.
[*][9] no-entry arming

This function is used to arm the alarm system while occupants are on the premises. Pressing [*][9] and then keying in an
access code arms the panel without an entry delay on delay type zones and bypasses stay/away and night type zones.
After the exit delay, delay 1 and delay 2 type zones behave the same as instant zones. Stay/away zones remain bypassed.
The entry delay can be activated or deactivated at any time while the system is armed using [*][9].
Note: If the alarm system is armed using [*][9], disarming is only possible from a keypad inside the premises unless a wire-
less key is used.
Note: Entry of a valid access code is required following this key only when the system is disarmed. When armed, if pro-
gramming section [015] option 4 (Quick Arming/Function Key) is off, an access code entry is required.
Global delay zones always have an entry delay, even if the system is armed using [*][9].
- 70 -
[*][0] quick arm/exit

This feature operates differently depending on whether or not the alarm system is armed or disarmed.
Note: This feature shall not be used for EN50131 certified systems.
When disarmed:
Pressing [*][0] arms the alarm system without having to enter an access code. This provides a fast method of arming for reg-
ular users and allows users without an access code to arm the system.
Note: The Quick Arm feature (section [015] option 4) must be enabled in order for this function to operate as intended. Func-
tion keys also will not require an access code when this option is enabled.
When armed:
This feature provides a means to exit the premises while the alarm system is armed without having to disarm then rearm it.
Pressing [*][0] starts a 2-minute timer that enables any door programmed as a delay zone to be opened and closed once
without triggering an alarm.
If the door is not closed at the end of the 2-minute timer, the entry delay sequence begins. Any additional activity on another
zone triggers the associated alarm or delay sequence.
4.8 Visual verification

This feature enables the central station operator to view captured images of the premises in the event of an alarm event.
Combination camera/motion detectors can be installed throughout the premises to provide visual verification coverage. The
microphone on the camera PIR can be disabled.
Visual verification sessions are triggered by the following:
l Fire key
l Medical key
l Panic key
l Alarms detected by armed PIR Cameras
To set up visual verification on a partition:
l Enroll the camera PIR; [804]
l Set visual verification options; [804]>[841]:
l [001] Visual Verification Enable/Disable
l [002] View Time Window
l [003] View Other Alarms
l Input a custom label to identify the camera PIR; [000]>[001]
l Enable this option on the alternate communicator (in [851]>[010] option 2).
Refer to the Camera PIR installation manual for more details.
Note: Visual Verification has not been evaluated by UL and shall be disabled for UL certified installations.
Note: While an image is being transferred from the PIR camera to a central station receiver, the product cannot capture addi-
tional images.
- 71 -
Section 5: Programming
5.1 How to program
This section describes how to view alarm system programming options using the supported keypad types.
5.2 Programming methods

The alarm system can be programmed using the following methods:
Table 5-1 Programming Methods
Method Description Procedure
Template Use pre-defined templates to quickly apply basic pro- Press [899] at the “Enter Section” screen.
programming gramming and to set up DLS downloading. See Template Programming below for details.
DLS Download and apply programming using DLS 5 For local DLS, use a micro USB cable or a Wi-Fi
programming dongle and laptop with DLS-5 software installed.
For remote DLS, use a telephone line, cellular net-
work or the Internet.
Installer Manually program all alarm system and device Press [*][8][installer code] while the system is dis-
programming options. armed.
Template programming
Template programming allows the installer to quickly program the minimum functions required for basic operation. The
installer is prompted to enter a 5-digit code that selects predefined programming configurations:
Digit 1 – zone 1-8 definition options
Digit 2 – system EOL options
Digit 3 – alarm controller communications options
Digit 4 – alarm controller call directions
Digit 5 – DLS connection options
(See "Template programming tables" on page 258 for programming information).
Perform template programming after completing the hardware installation. Ensure you have the information listed below
available. Record this information in the programming worksheets for future reference:
l Monitoring station telephone number - provided by the alarm monitoring service.
l Monitoring station account code - provided by the alarm monitoring service.
l Downloading access code.
l Entry delay - installer defined.
l Exit delay - installer defined.
l Installer code - programmable, unique 4-digit code. The default value is [5555].
To perform template programming:
1. Enter [*][8][installer code][899]. If this section has been entered accidentally, press # to exit and the system programming
will not be changed.
2. At the “Enter Data” screen, enter a 5-digit value representing the desired programming options. Reference the template
programming tables to determine what values are required for the installation.
Once the 5-digit number has been entered, the installer cannot exit until all sections are completed. Enter new data
and/or press the [#] key to accept the displayed data and proceed to the next section. Changing a single digit, then
pressing the [#] key advances to the next section but does not save the changed data.
3. After entering a 5-digit template programming value, the first telephone number is displayed. Enter the monitoring station
telephone number after the “D.” Press [#] to complete the entry.
- 72 -
4. After programming the first telephone number, enter a system account code.
l The system account code can be any 4 or 6-digit combination of numbers (0-9) and letters (A-F).
l To enter letters A through F, press [*] then the numbers 1 through 6 for the letter A through F respectively. Press [*]
again to revert back to decimal entry. E.g., to enter “1234FF” press [1234*66].
See "[310] Account Codes" on page 122 for additional details. When the system account code programming is com-
pleted, enter a partition 1 account code using the same method as the system account code.
5. After programming the partition 1 account code, the downloading access code is displayed. Enter the new downloading
access code or press [#] to proceed to the next step. The downloading access code must changed from its default value.
6. The next value is a 3 digit partition 1 entry delay time. Press [>][>][>] to accept the default time of 30 seconds (030) or
enter an entry delay between 001 and 255. E.g., Press 020 for a delay of 20 seconds. See "System times" on page 84 for
additional details. The CP-01 models of the panel will not accept a value less than 30 seconds.
7. The next value is a 3 digit partition 1 exit delay time. Press [>][>][>] to accept the default time of 120 seconds or enter an
exit delay between 001 and 255. E.g., press 030 for a delay of 30 seconds. See "System times" on page 84 for additional
details. The CP-01 models of the panel will not accept a value less than 45 seconds.
8. After programming the exit delay, enter a 4, 6 or 8-digit installer code, depending on the value in "[041] Access Code
Digits" on page 113. See "[006] Installer Defined Access Codes" on page 86 for installer code details.
9. Template Programming will automatically exit after the installer's code has been programmed.
Note: EN50131-1 compliant systems using 1000 access codes shall set the access code to 8 digits (section [041], option
02).
DLS programming
DLS programming involves downloading custom programming using DLS software and a computer. This can be done loc-
ally or by remote.
Note: For UL listed systems an installer must be on the premises.
Local programming with micro USB or Wi-Fi adapter
Follow the steps below in the sequence indicated to set up local programming using DLS:
1. Connect AC Wiring.
In a new installation, the backup battery requires 24 Hrs. charging. AC Power is required for USB Programming until
the battery is charged.
2. Plug the USB header into the alarm controller. A DLS session is initiated on the DLS computer.
3. When the session is complete, remove the USB cable from the alarm controller.
4. Complete the installation.
Remote programming
DLS programming can be performed remotely by connecting to the alarm system via telephone line, cellular network or Eth-
ernet.
Refer to "[401] DLS/SA Options" on page 129. for details.
Note: AC Power must be present for the alarm system to answer incoming calls from DLS.
Installer programming
Installer Programming is used to manually program alarm system options. Access this mode by keying in [*][8][Installer
Code]. Use the scroll keys to navigate through the menus or jump directly to a specific section by keying in a section number.
Programming consists of toggling on and off options in each section or by populating data fields. For descriptions of all pro-
gramming options, see "Programming descriptions" on page 75
Viewing programming
Programming sections can be viewed from any system keypad.
Generally, programming options are accessed in the following way:
1. Enter Installer Programming mode ([*][8]).
- 73 -
2. Navigate to a specific programming section.

3. Select an option to view or change its programming.
All programming options are numbered and can be accessed by navigating through the menu, or by keying in the program
section number. For toggle options, the name of the option is displayed.
Use the keypad numbers to toggle options on or off. Sections requiring data input, such as phone numbers, display the full
data in fields up to 32 characters long. To input data, use the scroll keys to select a character then press the keypad button
corresponding to the number/letter required. Scroll to the next character and repeat the procedure as needed. Press the [#]
key to save changes and exit the program section.
The programming worksheets and descriptions later in this section provide a place to record custom programming settings
and are numerically listed to assist in locating specific sections.
Keypad types
The sections below describe how programming is viewed and interpreted using the supported keypad types. For more
information, see the instruction sheet included with the keypad.
LCD keypad
LCD keypads use a full-message display that provides visual and numerical navigation through the programming sections.
The Armed light illuminates when Installer Programming mode is activated. Use the scroll keys to move through menu
options and press [*] to select. Alternatively, enter a specific section number. The Armed light flashes to indicate a sub-sec-
tion has been selected. Press [*] to select a sub-section. The Ready light illuminates and the information programmed in the
section is displayed.
For programming sections with toggle options, press the corresponding number on the keypad to turn the option on or off.
The display changes accordingly.
Sections requiring data input, such as phone numbers, display the full data in fields up to 32 characters long.
To input data, use the scroll keys to select a character then press the keypad button corresponding to the number/letter
required. Scroll to the next character and repeat the procedure as needed.
For information on entering HEX data, see below.
Press the [#] key to exit the program section at any time. All changes made up to that point are saved.
Programming hex and decimal data

Hexadecimal (HEX) digits may be required during programming. To program a HEX digit, press the [*] key while in a pro-
gramming section that requires a data entry. HEX programming mode activates and the Ready light begins to flash.
The following table indicates which number should be pressed to enter the corresponding HEX digit:
Table 5-2 HEX Digit Programming
Value Enter Telephone Dialer
HEX [A] Press [*][1][*] Not supported
HEX [B] Press [*][2][*] Simulated [*] key
HEX [C] Press [*][3][*] Simulated [#] key
HEX [D] Press [*][4][*] Dial tone search
HEX [E] Press [*][5][*] Two-second pause
HEX [F] Press [*][6][*] End of number
The Ready light continues to flash after the HEX digit is entered. If another HEX digit is required press the corresponding
number. If a decimal digit is required, press the [*] key again. The Ready light illuminates and the panel returns to regular
decimal programming.
Example: To enter ‘C1’ for a closing by user 1, enter [*] [3] [*], [1]
[*] to enter hexadecimal mode (Ready light flashes)
[3] to enter C
[*] to return to decimal mode (Ready light is on)
[1] to enter digit 1
- 74 -
If an error is made while inputting data, press the [#] key to exit the section. Select that section again and re-enter the inform-
ation correctly.
When using a Contact ID format, a decimal zero [0] does not transmit for account and reporting codes. Programming a zero
[0] tells the alarm system not to send any pulses for that digit. Decimal zero [0] is a filler digit. To make a zero [0] transmit, it
must be programmed as a Hexadecimal ‘A.’
Example: For the 4-digit account number ‘4032’, enter [4] [*] [1] [*] [3], [2].
[4] to enter the digit 4
[*] to enter Hexadecimal mode (Ready light flashes)
[1] to enter A
[*] to return to decimal mode (Ready light is solid)
5.3 Programming descriptions

This section provides descriptions of all alarm controller options programmable by the installer.
Adding labels
[000] Label Programming
Zone and other labels on the alarm system can be customized.
Program labels locally or download/upload using DLS. Local label programming is done via a system keypad, as described
below.
[000] Language selection
To select a language:
1. Enter Installer Programming: [*][8][Installer Code].
2. Enter programming section [000]>[000].
3. Key in the 2-digit number corresponding to the language required. See the following table.
Table 5-3 Language codes
01 = English 11 = Swedish 22 = Bulgarian
02 = Spanish 12 = Norwegian 23 = Latvian
03 = Portuguese 13 = Danish 24 = Lithuanian
04 = French 14 = Hebrew 25 = Ukrainian
05 = Italian 15 = Greek 26 = Slovakian
06 = Dutch 16 = Turkish 27 = Serbian
07 = Polish 18 = Croatian 28 = Estonian
08 = Czech 19 = Hungarian 29 = Slovenian
09 = Finnish 20 = Romanian
10 = German 21 = Russian
[001]-[248] Zone Labels

Customized labels can be created for each available zone. Labels can be programmed at the keypad or down-
loaded/uploaded using DLS. The maximum label size is 14 x 2 ASCII characters.
Manual labels
The following procedure describes how to add zone labels using the LCD keypad:
2. Press [*], scroll to Zone Labels and press [*] again.The first zone is displayed. Alternately, press [000][001].
- 75 -
3. Scroll to the zone label to be programmed or key in the zone number. (e.g., 001 for zone label 1).
4. Scroll to the desired character’s location using the[<] [>] keys.
5. Enter the number of the corresponding character group until the desired character is displayed (see the following table).
Example: Press the “2” key 3 times to enter the letter “F.”
Press the “2” key 4 times to enter the number “2.”
To delete a character, use the [<] [>] keys to move the cursor under the character, then press [0].
If any key other than [<] or [>] is pressed before [0], the cursor moves one space to the right and deletes that char-
acter.
6. Press [#] to save the changes and exit.
Press To Select/Display
[*] [SELECT]
[#] [ESCAPE]
[0] [SPACE]
[1] [A], [B], [C], [1]
[2] [D], [E], [F], [2]
[3] [G], [H], [I], [3]
[4] [J], [K], [L], [4]
[5] [M], [N], [O], [5]
[6] [P], [Q], [R], [6]
[7] [S], [T], [U], [7]
[8] [V], [W], [X], [8]
[9] [Y], [Z], [9], [0]
Zone label options

To access zone label options such as using ASCII characters, changing letter case and clearing the display, press [*] while
in Zone Label programming. The Select Option menu is displayed. Use the [<] [>] keys to access the following options:
Option Description
WORD ENTRY Provides access to the Word Library, a collection of words commonly used when programming labels. See below for
details.
ASCII ENTRY Used to access uncommon characters or as a primary method for programming labels. 255 character entries are
available. Use the [<] [>] keys to scroll through the characters or enter a 3-digit number from 000-255. Press [*] to
select a character. See "ASCII characters" on page 264 for available ASCII characters.
CHANGE CASE This option toggles the letter between upper case (A, B, C) and lower case (a, b, c).
CLEAR TO END This option clears the display from the cursor to the end of the display.
CLEAR DISPLAY This option clears all characters.
SAVE Saves the new label.
Word library
The Word Library is a database of words commonly used when programming labels. Individual words can be combined as
needed (e.g., Front + Door). Words that do not fit on the first line are automatically moved to the bottom line.
To program a custom label using the Word Library:
2. Press [*], scroll to Zone Labels and press [*] again.The first zone is displayed. Alternately, press [000][001].
3. Scroll to the zone label to be programmed or key in the zone number (e.g., 001 for zone label 1).
4. Press [*] to open the Select Option menu.
5. Press [*] again to select the Word Entry option.
- 76 -
6. Enter the 3-digit number corresponding to a word (see "Word library" on page 257) or use the scroll keys [<][>] to view
words in the library.
7. Press [*] to select the word.
8. To add another word, repeat the above procedure from step 4.
9. To add a space, press the right scroll key [>].
10. To clear characters, select Clear to End or Clear Display from the Select Options menu.
11. To save the current label, press [#] to exit label programming.
[064] CO alarm message
Use this section to program a custom label that is displayed on keypads during a carbon monoxide alarm. The maximum
label size is 14 x 2 characters.
[065] Fire alarm message
Use this section to program a custom label that is displayed on keypads during a fire alarm. The maximum label size is 14 x
2 characters.
[066] Fail to arm event message
This message is displayed on all partition keypads if a user attempts to arm the system when it is not ready to arm. The mes-
sage clears after five seconds. The maximum label size is 16 x 2 characters.
[067] Alarm when armed event message
This message is displayed if an alarm occurred while the system was armed. The message is displayed when the system is
disarmed and remains on the screen for 5 seconds. Following this, the zones that went into alarm are displayed. The max-
imum label size is 16 x 2 characters.
[100] System label
Use this section to program a custom label for the security system. This label is used in the event buffer when system events
occur. The maximum label size is 14 x 1 characters.
[101]-[108] Partition 1-8 labels
Use this section to program a name for each partition for display on partition keypads and event messages. The maximum
label size is 14 x 2 characters. See "Programming" on page 72 for specific instructions on how to program labels.
[201]-[208][001]-[004] Partition command output labels
Use this section to program custom labels for command outputs. These labels are used with output activation events in the
event buffer. Enter subsection [201] to [208] to select partition 1 to 8, then enter subsection [001] to [004] to select command
output 1 to 4 label.
The maximum label size is 14 x 2 characters. See "Programming" on page 72 for specific instructions on how to program
labels.
[601]-[604] Schedule labels
Use this section to program custom labels for command output schedules. These labels are used to identify schedules for
PGM command outputs 1-4. The maximum label size is 16 characters. See "Programming" on page 72 for specific instruc-
tions on how to program labels.
[801] Keypad labels
Use this section to create custom labels for keypads on the system. Select 001-016 for keypads 1-16.
[802][001]-[030] HSM2108 Zone expander labels
Use this section to create custom labels for Zone expanders on the system. Select 001-030 for zone expanders 1-15.
[803][001]-[016] HSM2208 Output expander label
Use this section to create a custom label for the output expander. Select 001 for HSM2208. Select 001-016 for output
expanders 1-16.
- 77 -
[804][001]-[030] HSM3408 8 zone expander label

Use this section to create a custom label for the 8 zone expansion module. Select 001-030 for zone expanders 1-30.
[806] HSM2HOSTx PowerG transceiver label
Use this section to create a custom label for the 2-way wireless transceiver.
[808] HSM2955 audio verification module label
Use this section to create a custom label for the audio verification module.
[809][001]-[004] HS2300 power supply label
Use this section to create custom labels for power supplies on the system. Select 001-004 for power supply 1-4.
[810][001]-[004] HS2204 high-current output supply label
Use this section to create custom labels for high-current output supplies on the system. Select 001-004 for output supply 1-4.
[811][001]-[004] HSM3350 3 A power supply label
Use this section to create a custom label for the 3 A power supply module. Select 001-004 for power supply 1-4.
[812][001]-[008] HSM3204CX Corbus repeater label
Use this section to create a custom label for the Corbus repeater. Select 001-008 for Corbus repeater 1-8.
[815] Alternate communicator label
Use this section to create a custom label for the alternate communicator.
[820][001]-[016] Siren labels
Use this section to create custom labels for wireless sirens on the system. Select 001-016 for sirens 1-16.
[821][001]-[008] Repeater labels
Use this section to create custom labels for wireless repeaters on the system. Select 001-008 for repeater 1-8.
[999][Installer Code][999] Default labels
This section is used to return all labels to factory settings. Installer code is required to verify deletion.
Zone setup
The following section describes zone programming options. To program a zone type, first enter section [001] and then enter
a 3 digit zone number from 001 - 248. After entering a new zone type for the desired zone number, the keypad will auto-
matically advance to the next zone.
[001] Zone types
A zone type defines how a zone operates within the system and how it responds when triggered.
[001]-[248] Select Zone
Every zone on the system must be assigned a zone type. The available zone types are listed below.
000 – Null Zone
Assign to all unused zones.
001 – Delay 1
Commonly assigned to primary points of entry. Follows entry delay 1 and exit delay timers (section [005]). Arming the alarm
system starts the exit delay timer. After the exit delay has expired, opening the door starts the entry delay timer. During entry
delay, the keypad buzzer prompts the user to disarm the system.
002 – Delay 2
Commonly assigned to secondary points of entry (further from the keypad). Follows entry delay 2 timer (section [005]).
003 – Instant
Commonly used for perimeter doors and windows, this zone type follows the exit delay. The alarm is triggered instantly if the
zone is tripped after the exit delay expires.
- 78 -
004 – Interior
Commonly assigned to interior motion sensors near a point of entry, such as a foyer or hallway, that must be accessed to
reach the keypad. The alarm is activated if the system is armed and a delay type zone (e.g., front door) is not tripped first, or if
the entry/exit timer expires before the alarm is disarmed. Otherwise, the zone is instant if tripped.
005 – Interior Stay/Away
Similar to Interior zone type except that the system bypasses the zone when armed in Stay mode. Commonly used to activ-
ate perimeter zones while permitting free movement throughout the interior.
006 – Delay Stay/Away
Similar to delay 1 except that the zone is bypassed when armed in Stay mode. Commonly used with motion detectors that
cover an entry point.
007 – Delayed 24-Hour Fire
This zone is used with smoke detectors and functions similar to the standard fire zone, except the communicator delays the
alarm memory and transmission by 30 seconds. If the alarm is acknowledged by pressing any key, the siren is silenced and
the transmission aborted. If the smoke detector is not restored after the alarm has been acknowledged, the siren output activ-
ates after 90 seconds and another 30-second delay starts. A code is required to silence the alarm. A tamper or fault causes a
fire trouble to log and transmit.
Note: The supervision options (NC, SEOL, DEOL, TEOL) do not affect the functionality of this zone. The restored state of this
zone type is 5k6, the alarm state is short and the trouble state is open.
008 – Standard 24-Hour Fire
This zone is used with smoke detectors. The siren sounds instantly when the smoke detector is activated. If enabled, the com-
municator immediately transmits the alarm to the monitoring station. A tamper or fault of this zone type causes a fire trouble
to log and transmit.
zone type is 5.6k, the alarm state is short and the trouble state is open.
009 – Instant Stay/Away
Commonly assigned to interior motion sensors. This zone type is bypassed when armed in Stay mode, but functions like an
Instant zone [003] when armed in Away mode.
010 – Interior Delay
Commonly assigned to interior motion sensors. When Away armed, this zone type functions like the Interior zone type. When
Stay or night armed, tripping the zone activates entry delay 1. Tripping this zone during exit delay does not cause the system
to arm in Away mode, as tripping a regular Delay type zone does.
011 – Day Zone
Commonly used in areas where immediate notification of entry is desired. When disarmed, tripping this zone activates the
keypad buzzer but does not log or report the event. When armed, tripping this zone activates the siren then logs and reports
the event.
Note: An alarm during exit delay causes the siren to activate and remain on when exit delay expires.
012 – Night Zone
Commonly assigned to interior motion detectors in areas accessed during the night. This zone functions like an Interior
Stay/Away zone [005] when armed using any method except the following: If Stay armed, this zone is bypassed; if armed
using [*][1], this zone is bypassed.
016 – Final Door Set (Non CP-01 panels only)
UK This zone type does not use an exit timer (infinite exit delay). The door must be opened then closed to complete the arming
sequence. The arming method determines if infinite exit delay is applied. See the table below.
Note: Disable Exit Delay Termination with this zone type.
If this zone type is bypassed, the alarm system cannot be Away armed.
Arming method Infinite exit delay Arming mode
User code Y Away
Keyswitch Y Away
Away key Y Away
Wireless key away Y Away
- 79 -
*0 arm Y Away
*9 arm N Stay
Stay key N Stay
Wireless key stay N Stay
Remote Access/SMS - Do not use
DLS arm N Away
No activity arming N Away
Note: When Troubles/Open Zones Cancel Arming is enabled with this zone, any troubles or open zones on the system can-
cel arming when the zone is tripped and restored.
Due to the potential energy requirements of infinite exit delay, wireless keypads MUST be powered by a transformer.
If a wireless key is used to away arm the system, the door must still be opened then closed to complete the arming
sequence. The indoor siren will activate until the exit delay has expired.
017 – 24-Hour Burglary
This zone type is active at all times. It reports an alarm if the alarm system is armed or disarmed. This zone type sounds the
siren for the length of Bell time-out if the audible attribute is enabled.
018 – 24-Hour Bell/Buzzer
When the alarm system is armed and this type of zone is tripped, the siren activates for the duration of the bell time-out. If the
alarm system is disarmed when this type of zone is tripped, the keypad buzzer activates until an access code is entered.
023 – 24-Hour Supervisory
This zone is active and reports alarms at all times when tripped. The siren and keypad buzzer do not activate.
zone type is 5.6k, the alarm state is short and the trouble state is open. For use with normally open contacts.
024 – 24-Hour Supervisory Buzzer
When tripped, the keypad buzzer emits a steady tone until a valid access code is entered.
025 – Auto Verify Fire
(Hardwired smoke detectors)
When the zone is activated, a 30-second delay begins but no fire alarm sounds. If the same zone is activated again up to 60
seconds after the delay expires, the alarm is triggered immediately. If the same zone is activated after 60 seconds, the entire
sequence begins again.
If a second fire zone is violated during the auto-verify sequence, both zones a fire alarm is immediately triggered.
(Wireless smoke detectors)
When the zone is activated, a 40-second delay begins. The alarm is triggered if the zone is still faulted after 30 seconds. If
the zone is no longer in alarm, an 80-second verification timer begins. If any fire zone is activated during this period, the
alarm is triggered.
If another fire zone is activated during the auto verify sequence, both zones go into alarm immediately.
Note: Wireless smoke detectors used with this zone type must have a built in siren to act as a pre-alert to the system alarm.
zone type is 5.6kΩ, the alarm state is short and the trouble state is open.
027 – Fire Supervisory
When this zone is tripped, the keypad buzzer activates and a supervisory alarm is sent to the monitoring station. A valid
access code must be entered to silence the buzzer.
zone type is 5.6k, the alarm state is short and the trouble state is open.
040 – 24-Hour Gas
Instant alarm when activated, audible alarm at default.This zone type may be assigned to any device type.
041 – 24-Hour CO
This zone type is used with CO detectors. In the event of an alarm, a distinctive siren cadence is sounded. This is followed by
a 5-second pause and then repeated. After 4 minutes, the 5-second pause is extended to 60 seconds; however, BTO must
be programmed with a value of 5 minutes or higher. The siren is silenced when an access code is entered or the siren times
out.
- 80 -
zone type is 5k6, the alarm state is short and the trouble state is open. For use with normally open contacts.
042 – 24-Hour Holdup
Instant alarm when activated, silent alarm at default.
Note: Not for use in UL listed installations.
043 – 24-Hour Panic
Instant alarm when activated, audible alarm at default.
045 – 24-Hour Heat
046 – 24-Hour Medical
047 – 24-Hour Emergency
048 – 24-Hour Sprinkler
049 – 24-Hour Flood
051 – 24-Hour Latching Tamper
Instant alarm when activated, audible alarm at default. The alarm system cannot be armed until Installer Programming is
entered after the zone is restored.
052 – 24-Hour Non-Alarm
This zone is active at all times but does not cause an alarm. Zone attributes such as Zone Bypassing and Door Chime affect
the functionality of this zone. This zone type can also be assigned to a temperature sensor if indoor/outdoor temperature dis-
play is required without temperature warnings or alarm conditions.
056 –24 Hour High Temperature
This zone type is used with wireless temperature sensors and is activated when the temperature rises above a programmed
threshold (set in section [804][xxx][019-020]). Instant alarm when activated, audible alarm at default. This zone type gen-
erates an alarm when the system is armed or disarmed.
Note: This zone type cannot be used on hardwired zones. The temperature threshold includes a 3 °C (5-6 °F) difference
between a given state and its restored condition. For example, an alarm at 6 °C is restored at 3°C (High temperature) or 9°C
(Low temperature), depending upon the zone type selected.
The zone type for wireless temperature sensors must be 24 Hour High/Low Temperature in order for the sensor to operate
properly.
057 – 24-Hour Low Temperature
This zone type is used with wireless temperature sensors and is activated when the temperature drops below a programmed
threshold (set in section [804][xxx][019-020]). Instant alarm when activated, audible alarm at default. This zone type gen-
erates an alarm when the system is armed or disarmed.
Note: This zone type cannot be used on hardwired zones.
060 – 24-Hour Non-Latching Tamper
This zone is always active and reports a tamper condition with no audible alarm when opened or tamper/faulted.
061 - 24-Hour Masking
This zone is active 24 hours in either the armed or the disarmed state. This zone type does not generate an alarm, and does
not log in the Alarm Memory. This zone type generates a Masking Trouble on the system.
Note: This zone operates in SEOL only.
066 – Momentary Keyswitch Arm
Often used with a keyswitch module*, turning the key alternately arms and disarms the system and silences the alarms.
Tampers and faults only initiate their respective trouble sequence. The keypad gives no indication when this zone type is
activated.
- 81 -
Note: With audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad.
Using the keyswitch during the first 30 seconds of a delayed fire alarm is the same as pressing a key at the keypad (the 90
second delay starts). Activation of a keyswitch zone arms or disarms the system. Activation of this zone type is NOT logged
nor is the Police code transmitted. Bypassed zones of this type are not un-bypassed when the system is disarmed. When the
zone is bypassed, a zone bypass event buffer log and communication occurs immediately, NOT when the system is armed.
*Keyswitch module not for use in UL/ULC listed installations.
067 – Maintained Keyswitch Arm
Often used with a keyswitch module, turning the key (open state) arms the system. Turning the key back (restored state) dis-
arms the system. Tampers and faults only initiate their respective trouble sequence.
Note: DO NOT use for wireless zones. Activation of the zone does not log or transmit the Police code. Bypassed zones of
this type are not un-bypassed when the system is disarmed. When the zone is bypassed, a zone bypass event buffer log and
communication occurs immediately, NOT when the system is armed.
With an audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad.
Activating this zone type during the first 30 seconds of a delayed fire alarm is the same as pressing a key at the keypad (the
90 second delay starts). If left in the open state, the system does not arm until the zone is restored and tripped again.
068 – Momentary Keyswitch Disarm
Use with a keyswitch module. Activating and restoring this zone disarms the partition and silences alarms. Tampers or faults
do not disarm the zone.
Note: Do not use as a global zone.
069 – Maintained Keyswitch Disarm
Used with a maintained keyswitch. Activating this zone disarms the partition.
Tampers or faults on this zone do not disarm the partition.
071 – Doorbell Zone
This zone type sounds a chime through keypads on the partition when activated. No alarms are generated. Various chime
tones can be programmed. Disabling door chime on the partition also disables the chime on this zone.
Note: Do not use as a global zone.
072 – Push to Set (Non CP-01 panels only)
Activating this zone starts an infinite exit delay when armed according to the methods described in the table below. To com-
plete the arming sequence, this zone must be activated and restored. Once done, the exit delay timer starts.
Arming method Infinite exit delay Arming mode
User code Y Away
Keyswitch Y Away
Away key Y Away
*0 arm Y Away
*9 arm N Stay
Stay key N Stay
Night key N Night
Remote access/SMS - Do not use
DLS arm N Away
No activity arming N Away
Note: Do not use exit delay termination with this zone type. Away arming with this zone bypassed prevents arming.
If you silence a fire alarm by entering a user code, and the zones that imitated the fire alarm remain open, a Bells Silenced
message displays. The system automatically clears the message when all the fire zones are restored on the system. When
the Bells Silenced message displays, a user can still view all standard base menu messages.
Note: The Bells Silenced message also overrides the automatic display of the Alarm Memory feature for fire alarms.
[002] Zone attributes
Zone attributes are used to customize the operation of zones. When a zone type (section [001]) is programmed, the default
zone attribute is automatically assigned.
Note: These attributes override default settings. Do NOT change fire zone attributes from their default settings.
- 82 -
[001]-[248] Select Zone

The attributes listed below can be enabled and disabled for each zone.
01 – Bell Audible
ON: An alarm activates the siren.
OFF: Silent alarm.
02 – Bell Steady
ON: Siren output is steady when in alarm.
OFF: Siren output pulses when in alarm.
03 – Door Chime
ON: The keypad chimes when the zone is open and when the zone is secured.
OFF: The zone does not chime.
04 – Bypass Enabled
ON: The zone can be manually bypassed.
OFF: The zone cannot be bypassed.
Note: Bypass shall not be enabled for fire zones.
05 – Force Arm
ON: The system can be armed with the zone open. The zone is temporarily bypassed and, when secured, is monitored by the system.
NOTE: When open zones cancel arming is enabled [021][7], the system can begin arming with an open, force armable zone, but if the zone is still
EN
open when the exit delay timer expires, the arming will be cancelled.
OFF: The system cannot be armed if the zone is open.
06 – Swinger Shut Down
ON: When the zone goes into alarm for the number of times programmed in the Swinger Shutdown Counter (See "[001] – Swinger Shutdown" on
page 123), it shuts down with no further transmissions sent to the monitoring station during that armed period. The siren follows swinger shutdown
if programmed.
OFF: Swinger shutdown is disabled. All alarms are transmitted.
07 – Transmission Delay
ON: Reporting of zone alarms is delayed for the programmed time in section 377 (See "[002] – Communication Delays" on page 124). If a valid
access code is entered within this time, no alarm signal is communicated.
OFF: When an alarm occurs, the reporting code is transmitted immediately.
08 – Burglary Verification
ON: Enabled for cross zoning/police code. Zone alarms are not communicated until a burglary verified event occurs.
OFF: Not enabled for cross zoning/police code.
09 – Normally Closed (NC)
ON: The zone requires a normally closed loop.
OFF: The zone follows programming in section [013] option 2.
See note after option 11.
10 – Single End of Line (SEOL) Resistors
ON: The zone requires a single end-of-line resistor (5.6K).
See note after option 11.
11 – Double End of Line (DEOL)
ON: The zone requires two end-of-line resistors (5.6K).
Note: If more than 1 option is enabled for options 09, 10, and 11 the lowest attribute number takes precedence. If options 09
and 10 are both enabled the zone follows the normally closed loop configuration.
12 – Fast Loop/Normal Loop Response
ON: Follows a fast loop response of 40ms.
OFF: Follows a normal loop response as programmed in the Zone Loop Response Time section.
- 83 -
13 – 2-Way Audio Attribute

ON: Panel is able to initiate a 2 way audio session.
OFF: Only the microphone turns on, initiating a a Listen-in only session. The speaker remains off.
14 – Hold Up Verification
ON: An alarm from zones of this type can contribute to a verified hold up alarm. Use this attribute with Panic and Hold Up zones.
OFF: An alarm from zones of this type does not contribute to a verified hold up alarm. The zone does not cause the hold up verification timer to start
counting down, or generate a verified hold up if the alarm is detected while the timer is running.
15 - Triple EOL
ON: The zone requires triple-end-of-line resistors.
EOL resistance
This section describes how to program EOL resistances to custom values.
[004] End of line resistance
Use this menu to program custom resistance values for SEOL, DEOL, and TEOL options in 3-digit format. For example, to
program the value of 0.5 kΩ, enter 005.
[001] – Single EOL
Alarm
Default value: 5.6 kΩ
Programmable range: 0.5 kΩ to 28 kΩ (005 to 280)
[002] – Double EOL
Alarm
Programmable range: 0.5 kΩ to 15 kΩ (005 -150)
Tamper
[003] – Triple EOL
Alarm
Programmable range: 0.5 kΩ to 7.5 kΩ (005 -075)
Tamper
Programmable range: 0.5 kΩ to 7.5 kΩ (005 -075)
Fault/Mask
Default value: 10 kΩ
System times
This section describes how to program various timers applicable to the entire alarm system.
[005] System times
This is the base menu used by installers to program timers, including system area [000], partition timers [001]-[008], and day-
light saving time [901]/[902].
[000] – System Area
Bell Cutoff Time
System sirens follow this timer. Fire alarms follow this timer if section [014] option 8 (Fire Bell Continues Option) is off. System tampers follow this
timer. The bell cutoff time is programmed in minutes. Valid entries are 001 to 255 minutes.
- 84 -
Keypad buzzer alarms do not follow this timer.

Bell Delay Time
The Bell Delay Timer determines how long the bell will be delayed after a zone alarm event. Valid entries are 000-255 where 000 disables this
feature.
Burglary Verification Timer
If another zone with the Burglary Verification attribute enabled is violated within the duration of this timer, a burglary verified event is communicated
and logged. “Burglary Verified” is displayed on the keypad when the system is disarmed.
The burglary verification timer is programmed in minutes. Valid entries are 000 to 255 minutes.
Holdup Verification Timer
A holdup alarm is immediately communicated to the monitoring station and the holdup verification timer starts. A programmable counter
determines the number of additional holdup events that must occur before the timer expires to create a verified holdup event. Once this happens,
the holdup event is logged and communicated.
Note: Not for use with UL/ULC listed installations. 000 disables this feature.
Zone Loop Response Time
Loop response time is a 3-digit entry from 005 to 255 programmed in 10ms increments. The minimum available loop response time is 50ms (e.g.,
program 005 for 50ms).
Automatic Clock Adjust
This value adds or subtracts seconds from the system clock at the end of each day to compensate for inaccuracies. To determine the adjustment
value, monitor the time lost or gained by the alarm system over a period of time and calculate the average gains or loses.
Example #1: The clock loses an average of 9 seconds per day. Program the alarm controller to adjust the clock by 51 seconds for the last minute of
each day. This speeds up the alarm controller’s clock by 9 seconds, correcting the problem.
Example #2: The clock gains an average of 11 seconds per day. Program the alarm controller to adjust the clock by 71 seconds for the last minute
of each day. This slows down the alarm controller’s clock by 11 seconds, correcting the problem.
If the Auto-arm time is set for 23:59, any change to the Clock Adjust option will directly affect the Auto-arm pre-alert time.
[001]-[008] Partition 1-8 Timers

The following timers can be applied to each partition.
Note: For UL installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.
Entry Delay 1:
This value determines the entry delay time for delay 1 type zones. Valid entries are 001 to 255 seconds.
Entry Delay 2:
This value determines the entry delay time for delay 2 type zones. Valid entries are 001 to 255 seconds.
Note: The system follows the entry timer that activates first.
Exit Delay:
This value determines the exit delay time when arming the system. During exit delay, both the Ready and Armed LEDs are on. When the exit delay
expires, both LEDs turn off.
EN Note: European products will only activate the armed LED at the end of exit delay.
Settle Delay:
This timer enables a programmable, short duration bypass of all zones on the partition at the time of arming. It allows motion detectors to restore
when the system is armed to help prevent false alarms.
The typical value for this timer is 5 seconds, but can be increased if false alarms persist. Program 000 for no settle delay.
The settle delay duration is programmed in seconds. Valid entries are 000 to 010 seconds.
[900] – Bell Delay Partition Mask
This option enables or disables the Bell Delay feature for individual partitions. When the option is enabled, Bell Delay is
applied to the selected partition during alarm conditions. When the option is disabled, Bell Delay is not applied. The default
setting is (Y): enabled.
[901]/[902] – Daylight savings begin/end
Daylight Begin [001] and Daylight End [002]:
Set the date and time daylight savings starts and ends.
- 85 -
Month
Valid entries are 001-012 (January to December).
Week
Valid entries are 000-005.
Enter “000” to program a specific date (1-31) in the Day field. Enter 001-005 to program the specific week of the month. 005
is the last week of the month.
Day
1-31 (if 000 is programmed in the Week field). 0-6 (Saturday-Sunday) if 001-005 is programmed in the Week field.
Hour
Valid entries are 00-23 hours. This is the time of day to advance or turn the clock back.
Increment
Valid entries are 1 or 2 hours. This is the number of hours to advance or turn the clock back.
Access Codes
This section is used by installers to program the installer code, the master code and the maintenance code. For information
on programming other access codes, see "[*][5] Program access codes" on page 64.
[006] Installer Defined Access Codes
This is the base menu used by installers to program the installer code [001], the master code [002] and the maintenance
code [003]. See below for details.
[001] – Installer Code
This code is used by the installer to gain access to Installer Programming [*][8]. Users with this access code have access to
all levels of system programming.
EN Note: For EN50131-1 approved installations the installer code cannot change the master code or any other level 2 codes.
[002] – Master Code
This code is used by the master user, a person designated to perform operational tasks beyond those of the standard user.
The master code provides access to functionality in the [*][5] and [*][6] menus.
[003] – Maintenance Code
This code is usually assigned temporarily to maintenance personnel who must deactivate the alarm to enter the premises.
The maintenance code can arm and disarm the system, but does not grant access to any other functionality.
UK [005] – Code Version
A programmable 3-digit pin is required to calculate the 5-digit remote reset code. The range of the pin is 000-255 in
decimal. The default value of the pin code is 000.
[007] - [008] PGM Configuration

This section describes how to set up and configure programmable outputs.
PGMs are used to send electrical current to external devices such as lights and sirens, usually when an alarm event occurs.
The alarm controller provides up to two 100mA PGMs and two 300mA PGM. PGM outputs can be expanded using the
optional 8-output expander (HSM2208), the 4 high-current output expander (HSM2204) and the Corbus Repeater
(HSM304CX) with 4 relay PGM outputs.
Programming an output is a four-step process:
1. Program the PGM
2. Assign the PGM to a partition.
3. Assign an output attribute.
4. Assign an output option.
See "[011] PGM Configuration Options" on page 100 for PGM slot assignment.
- 86 -
[007] PGM Programming

This is the base menu used by the installer to assign PGMs to the main bell and a partition.
[000] Main Bell Partition Assignment
This programming section is used to define which partitions activate the main bell when they go into alarm. All partitions are
selected by default.
[001]-[324] PGM Partition Assignment
This option enables the installer to assign each PGM output to a partition. To assign a PGM to a partition, first select the PGM
output (PGM 001-324), then select the partition (1-8).
Note: This field is only supported by PGM types that have multiple partition capabilities (e.g., command outputs, away arm-
ing). It does not affect system outputs (e.g., ground start pulse).
[008] PGM Timer Programming
[000] PGM Minutes/Seconds
This option determines if the timer is in minutes or seconds.
[001]-[324] PGM Timer
This timer programs the duration (in seconds or minutes) that PGMs 1-324 activate if programmed to follow the PGM Timer.
Select option 001-324 for PGM 1-324.
This option does not affect outputs programmed as Sensor Reset.
[009] PGM Types

The output types described in this section can be assigned to alarm controller and output expander module PGMs. Each
alarm controller supports up to 4 PGMs and can be expanded using HSM2208 output expander, HSM3204CX and
HSM2204 High-Current output modules. PGM attributes are defined in section "[010] PGM Attributes" on page 92.
[001]-[324] Select PGM
100 – Null PGM
This option deactivates the PGM output
101 – Burglary and Fire Bell Follower
This PGM output follows:
l Fire pre-alerts
l Temporal three fire signal (if enabled)
l All audible burglary and fire alarms by partition
l Bell cut-off time
l Bell squawk conditions
l Audible exit fault
This output activates when the alarm output is active and turns off when the alarm output is silenced. The siren pattern
matches the programmed cadence for the zone that went into alarm. Cadence priority is as follows:
l fire alarm cadence
l CO alarm cadence
l other alarm cadences
The main siren still activates for all alarms.
102 – Delayed Fire and Burglary
This output type operates the same as the Burglary and Fire Bell Follower (PGM type 01), but does not activate until the trans-
mission delay time expires.
When a zone with transmission delay enabled is tripped, the Bell, Regular Fire and Burglary PGMs activate. At the end of the
transmission delay, the delayed Fire and Burglary output activates.
This PGM is usually used to control outdoor sirens. If a false alarm occurs, the user has time to disarm the system before the
external sirens activate.
Note: If a zone alarm occurs but does not follow transmission delay, this PGM activates immediately, even if transmission
delay is active for a different zone alarm.
- 87 -
This output activates for audible exit fault and does not interfere with the operation of any other programmable output.
103 – Sensor Reset [*][7][2]
This output is normally active and deactivates for 5 seconds when a [*][7][2] fire reset command is entered or when an auto
verified fire alarm is detected. This option is used to reset power for latching smoke detectors. The keypad buzzer does not
sound for the 5-second period. See "Smoke detector wiring" on page 40 for instructions on wiring smoke detectors.
104 – 2-Wire Smoke
When this PGM is programmed, the onboard PGM functions as an input instead of an output. 2-wire smoke detectors can be
connected to this input, which means that a zone input does not need to be used.
The PGM is also supervised, and a trouble condition is generated if a 2.2KΩ resistor is not present between the PGM ter-
minal and Aux+.
The 2-wire smoke detector input creates an instant and latching alarm.
107 - External Siren
This output is normally active and provides up to 1A to charge the external sirens battery. When an alarm occurs on the sys-
tem, this PGM triggers and deactivates the voltage to the siren, which causes the siren to sound alarm using power from the
backup battery. Use this output with Grade 3 external battery-operated sirens.
Note: This PGM type works on PGM 3 only.
109 – Courtesy Pulse
Courtesy pulse causes an output to activate for the entry and exit times, plus 2 minutes. This option is typically used to activ-
ate a courtesy light near the exit door for the duration of the entry/exit times.
111 – Keypad Buzzer Follow
PGM output activates with the keypad buzzer when triggered by the events below. The PGM output remains active for the
duration of the keypad buzzer.
l 24-hour supervisory buzzer zone alarm
l Auto-arm and no activity arming pre-alert.
l No activity arm pre-alert
l Entry delay
l Audible exit fault
l Audible exit delay
l Door chime
This PGM type does not activate for local key presses or trouble beeps.
114 – Ready to Arm
This PGM activates when the system is ready to arm (all non-force armed zones on the system are restored). The PGM out-
put de-activates when an access code is entered to arm the system and the exit delay begins. This PGM operates as
described during walk test mode (if all zones are restored).
115 – System Armed Status
This output activates when all selected partitions are armed (end of the exit delay) in either Stay or Away modes. The output
de-activates when the system is disarmed.
116 – Away Armed Status
This PGM switches on when the system is armed with stay/away zones activated. If the system is armed with the stay/away
zones always active, then the away output is active.
117 – Stay Armed Status
This PGM output activates if the system is armed with the stay/away zones bypassed.
120 – Away Armed with No Zone Bypasses Status
When assigned to a single partition, this PGM output activates when the system is armed with stay/away and night zones act-
ive, and no zones are bypassed.
- 88 -
If assigned to multiple partitions, all partitions must be armed in away mode with no bypassed zones before the PGM activ-
ates. If a force armable zone is violated at the time of arming, the PGM does not activate. When the zone is restored, the
PGM activates.
121-124 – Command Outputs 1-4
Command Outputs 1-4 are user-activated by entering [*] [7] [1-4] at any keypad. When an output is activated, three acknow-
ledgment beeps are sounded.
PGM outputs of this type can be programmed to follow a pre-defined schedule (programmed in section "[601]-[604] Sched-
ule labels" on page 77). Even if the output follows a schedule it can be manually turned ON, OFF or follow the schedule
through [*][7].
To select a schedule for these PGM outputs to follow, see "[009] PGM Types " on page 87.
129 – Partition Status Alarm Memory
This feature is intended to be used on a keyswitch plate, with a light controlled by this PGM to indicate system status. When
the partition is armed, the output activates (steady) at the:
NA beginning of exit delay
EN end of exit delay.
If an alarm occurs on the armed partition, the output flashes for the remainder of the armed period. If an alarm occurs on a
disarmed partition (24 Hr Zone), the output flashes until the alarm is acknowledged.
This output will not activate during a walk test or for FMP key, holdup or audible/silent PGM2 input alarms.
132 – Holdup Output
When a Holdup zone (Type [042]) goes into alarm, this output activates until the partition is either armed (access code, key-
switch, [*][0], etc.) or disarmed. A tamper or fault on a holdup zone type does not activate this output. This output does not
activate in Walk Test mode. If a global holdup alarm occurs, each partition with holdup zones assigned must be armed or dis-
armed before the holdup output deactivates. If holdup alarms occur on multiple partitions, an access code must be entered
at each partition before the output deactivates.
Note: Not for use with UL/ULC listed installations.
134 – 24-Hour Silent Input (PGM 2)

With this input the keypad does not indicate an alarm, the siren remains silent, and the signal is sent to the central station.
This input does not follow swinger shutdown. A 2.2KΩ EOL resistor is required for this input (to Aux+). If a short or open
occurs, an alarm is generated.
UL Note: Not for use with UL installations.
135 – 24-Hour Audible Input (PGM 2)
LCD keypads indicate that the system is in alarm, the siren sounds for the duration of bell timeout, and the signal is sent to
the central station. This input does not follow swinger shutdown. A 2.2KΩ EOL resistor is required for this input (to Aux+). If a
short or open occurs, an alarm is generated for all partitions and sirens. PGM partition assignment does not affect this PGM
type.
146 – TLM and Alarm
This output activates when a telephone line fault condition is present AND an alarm occurs. The output remains active until
an access code is entered to disarm or the TLM trouble is restored. The output activates for all audible and silent alarms
(except duress) if a TLM trouble is present. If an alarm activates this output in the disarmed state, it will deactivate when the
system is armed or the telephone line is restored. This output type also activates if alarms are in memory (not only for cur-
rently active alarms) when the TLM fault occurs. The alarms in memory must have exceeded the bell timeout.
147 – Kissoff
This PGM output activates for two seconds after the alarm system receives a kissoff signal from the central station.
148 – Ground Start
This output activates for two seconds before the alarm system attempts dialing to obtain a dial tone on Ground Start tele-
phone equipment. Two 2-second pauses must be inserted at the beginning of the telephone number when using this option.
- 89 -
149 – Alternate Communicator

This output can be used to trigger inputs on a third-party communicator for the purpose of triggering alarm communications
to a monitoring station. This output can be programmed to activate when any of the following system events (alarms) occur
on the system:
l Fire (Fire Key, Fire Zones)
l Panic (Panic Key and Panic Zones)
l Burglary (Delay, Instant, Interior, Stay/Away and 24-hour Burglary Zones)
l Opening/Closing Events
l Zone Auto-Bypass. (Please see 08 – Zone Auto-Bypass for details).
l Medical (Medical Key, Medical and Emergency Zones)
l Burglary Verified
l Opening After Alarm
l Emergency Alarm
l Duress Alarm
l Holdup Verified
In the armed state, this output deactivates when the system is disarmed. If an alarm activates this output in the disarmed
state, the output deactivates if a valid access code is entered within the bell timeout or if the system is armed after the bell
timeout has expired.
This output activates for silent and audible alarms or medical conditions only. It will not activate during pre-alert or delays.
Note: The PGM attributes for this option, programmed in section [010], differ from the standard selection of attributes nor-
mally programmed.
Note: When this PGM is configured to provide Opening/Closing status, the PGM must be programmed as a timed output, not
latching.
155 – System Trouble
This output can be programmed to activate when any of the following trouble conditions are present:
l Service Required
l Loss of Clock
l DC Trouble
l Bus Voltage
l AC Trouble
l Device Fault
l Device Low Battery
l Device Tamper
l RF Delinquency
l Module Supervisory
l Module Tamper
l Communications
l Not Networked
This output deactivates when all of the selected trouble conditions are cleared.
156 – Latched System Event (Strobe)
This output can be used to notify the home owner, before they enter the premises, that an alarm has occurred. This output
can be programmed to activate when any of the following alarms occur on the system:
l Burglary (Delay, Instant, Interior, Stay/Away and 24-Hour Burglary Zones)
l Fire (Fire Key, Fire Zones)
l Panic (Panic Key and Panic Zones)
l Medical (Medical Key, Medical and Emergency Zones)
l Supervisory (Supervisory, Freezer and Water Zones)
l Priority (Gas, Heat, Sprinkler and 24-Hour Latching Zones)
l Holdup (Holdup zones)
l Output follows pulse timer (See "[008] PGM Timer Programming" on page 87).
l Duress
l Emergency
l CO Alarm
l Fire Supervisory
l Fire trouble
- 90 -
This output does not activate during pre-alert or delays.

In the armed state, the output deactivates only once the system is disarmed.
If an alarm activates this output in the disarmed state, the output deactivates when a user enters a valid access code during
bell timeout. The output also deactivates if someone arms the system after the bell timeout has expired.
If assigned to a single partition, the output activates when an enabled alarm event occurs on the assigned partition. When
assigned to multiple partitions, the output activates when an alarm occurs on any partition and, if configured to latch, will
deactivate when any partition is disarmed. (or a valid disarming procedure is used).
157 – System Tamper
This output activates when any tamper condition is present and deactivates when all tamper conditions are cleared (if set for
steady operation). If set for a pulsed operation, the output deactivates when the PGM Output timer expires. These tampers
include zone tampers (DEOL), case tampers, TLM trouble, RF jam, and all zone and device tampers.
Note: This PGM does not activate for alternate communicator fault.
161 – DC Trouble
This output activates when one of the following low battery conditions is detected:
l Alarm controller low or absent battery
l Module low or absent battery
l Wireless zone low battery
l Wireless keypad low battery
l Wireless siren low battery
l Wireless key low battery
The output can be configured to follow the state of the low battery trouble(s) or it can activate for a period of time and auto-
matically restore.
165 – Proximity Tag Used
This output activates when the selected proximity tag is presented.
Assign this output to a user by entering a user number from 0002 to 1000. To enable this attribute for all proximity tags, enter
000 in PGM Configuration [011]. See "[007] - [008] PGM Configuration" on page 86
166 – Partition Prox Used
This output activates when a proximity tag is presented at a system keypad equipped with a proximity tag reader, including
global keypads. The proximity tag must be assigned to a valid user and the PGM must be assigned to a partition that the
user has permission to access.
Assign this output to a partition in section [007], PGM Partition Assignment. Use section [011], PGM Configuration Options, to
assign a schedule. When [011] is programmed as 000, the output activates any time a valid proximity tag is presented. When
[011] is programmed as 1-4, the output activates only when the proximity tag is presented during the scheduled interval.
175 – Bell Status and Programming Access Output
This PGM activates when the siren, Installer Programming mode or DLS/SA is active. It deactivates after bell timeout, when
Installer Programming is exited or when DLS/SA programming is disconnected.
176 – Remote Operation
This output is activated and deactivated remotely on command from DLS software.
184 – Open After Alarm
This output activates when the system has been disarmed after an alarm. It deactivates when a valid user code is entered or
when the PGM Output timer expires.
200 – Zone Follower - PGM By Zone
This option allows the PGM to activate when the assigned zone is opened and deactivate when the zone is restored or, if pro-
grammed, when a valid access code is entered. This PGM follows the state of the assigned zone, regardless of the partition
the zone or PGM is assigned to.
To program which zone the PGM will follow, see "[011] PGM Configuration Options" on page 100.
- 91 -
201-231 – Zone Follower (Zones 1-248)

This output type is assigned to a group of zones and is normally activated, but deactivates when a zone is tripped. Zones are
assigned to this output in the following groups:
Zone Group Zones Zone Group Zones

001 1-8 017 129-136
002 9-16 018 137-144
003 17-24 019 145-152
004 25-32 020 153-160
005 33-40 021 161-168
006 41-48 022 169-176
007 49-56 023 177-184
008 57-64 024 185-192
009 65-72 025 193-200
010 73-80 026 201-208
011 81-88 027 209-216
012 89-96 028 217-224
013 97-104 029 225-232
014 105-112 030 233-240
015 113-120 031 241-248
016 121-128
If multiple zones are enabled, any active zone in that group triggers the output. The PGM will not activate again until all
zones are restored.
[010] PGM Attributes

The following options are used to program the operating characteristics of the main bell and PGM outputs.
[000] Main Bell Mask
This programming section is used to configure the types of audible alarms that trigger the main bell output on the alarm con-
troller. All options are selected by default.
Fire Alarm
ON: Fire alarm ([F] key, Fire zones) activates the main siren.
OFF: Fire alarm does not activate the main siren.
CO Alarm
ON: CO alarm activates the main siren.
OFF: CO alarm does not activate the main siren.
Burglary Alarm
ON: Burglary alarm (Delay, Instant, Interior, Stay/Away, Night, Interior Delay, Instant Stay/Away, Day, 24-hour Burglary) activ-
ates the main siren.
OFF: Burglary alarm does not activate the main siren.
24-Hour Flood Alarm
ON: Main bell activates in the event of a 24-Hour Flood alarm.
OFF: Main bell does not activate in the event of a 24-Hour Flood alarm.
Bell Squawks
ON: Squawks activate the main siren. Bell squawks must be enabled to use the following options:
- 92 -
l Bell Squawk on arm (single)

l Bell Squawk on disarm (double)
l Bell Duration Auto-Arm (single every second)
l Bell Squawk on Exit (single every second)
l Bell Squawk on Entry (single every second)
l Bell Squawk on Trouble (single every 10 seconds)
OFF: Squawks do not activate the main siren.
[001]-[324] PGM 001-324 Attributes
The following PGM attributes can be assigned to a PGM. Each attribute has various toggle options, depending on the PGM
type selected (section [009]).
101 – Fire and Burglary
01 – True Output/Inverted
ON: deactivated during normal operation. Activated when triggered.
OFF: active during normal operation. Deactivated when triggered.
102 – Delay Fire and Burglary
103 – Sensor Reset [*][7][2]
03 – Access Code Required / No Code Required
ON: Access code required for activation
OFF: No access code required for activation
107 – External Siren
109 – Courtesy Pulse
ON: deactivated during normal operation, activated when triggered.
OFF: activated during normal operation, deactivated when triggered.
02 – Timed Output
ON: output remains active until the PGM output timer expires.
OFF: output remains active until the buzzer condition ends.
09 – Entry Delay
ON: activates on entry delay.
OFF: does not activate on entry.
10 – Exit Delay
ON: activates on exit delay.
OFF: does not activate on exit delay.
- 93 -
11 – Door Chime
ON: activates when chime is enabled.
OFF: does not activate when chime is enabled.
12 – Keypad Buzzer Zone
ON: activates when keypad buzzer goes into alarm.
OFF: does not activate when keypad buzzer goes into alarm.
13 – Audible Exit Fault
ON: activates when audible exit fault pre-alert begins.
OFF: does not activate when audible exit fault pre-alert begins.
14 – Auto-Arm Pre-Alert
ON: activates when auto-arming pre-alert begins.
OFF: does not activate when auto-arming pre-alert begins.
114 – Ready To Arm
115 – Armed Status
116 – Armed Away Mode
117 – Armed Stay Mode
120 – Away Armed with No Zone Bypasses Status
121-124 – Command Output 1-4
02 – Timed Output / Latched Output
OFF: output remains active until an access code has been entered.
03 - Access Code Required / No Code Required
ON: access code required for activation.
OFF: no access code required for activation.
129 – Partition Status Alarm Memory
- 94 -

146 – TLM Alarm
147 – Kissoff Output
148 – Ground Start
04 – Fire Alarm
ON: activates with fire alarm, [F] key, fire zones, 2-wire smoke.
OFF: does not activate with fire alarm.
05 – Panic Alarm
ON: activates with panic alarm, [P] key, panic zones.
OFF: does not activate with panic alarm.
06 – Burglary Alarm
ON: activates with burglary alarm.
OFF: does not activate with burglary alarm.
07 – Open/Close
ON: activates with opening or closing.
OFF: does not activate with opening or closing.
08 – Zone Auto-Bypass
ON: activates when a zone is automatically bypassed.
OFF: does not activate when a zone is automatically bypassed.
09 – Medical Alarm
ON: activates with medical alarm, [+] key, medical zones.
OFF: does not activate with medical alarm.
10 – Burglary Verified
ON: activates with burglary verified alarm (or police code).
OFF: does not activate with burglary verified alarm.
ON: activates when the system is disarmed with an alarm in memory.
- 95 -
OFF: does not activate when the system is disarmed with an alarm in memory.
12 – Emergency Alarm
ON: activates with zone emergency alarm.
OFF: does not activate with zone emergency alarm.
13 – Duress Alarm
ON: activates with duress alarm.
OFF: does not activate with duress alarm.
14 – Hold Up verified
ON: activates when a verified holdup event is detected.
OFF: does not activate when a verified holdup event is detected.
155 – System Trouble
04 – Service Required
ON: activates on service required trouble condition.
OFF: does not activate on service required trouble condition.
05 – Loss of Clock
ON: activates on loss of clock trouble condition.
OFF: does not activate on loss of clock trouble condition.
06 – DC Trouble
ON: activates if a panel low or no battery trouble is detected, or if an HSM2204/2300 1-4 low or no battery trouble is
detected.
OFF: does not activate on DC Trouble condition.
07 – Bus Voltage
ON: activates when a system module has measured a low Aux voltage.
OFF: does not activate for a module low voltage trouble.
08 – AC Trouble
ON: activates when any system device detects an AC Failure condition.
OFF: does not activate for AC Failure conditions.
09 – Device Fault
ON: activates if one of the following device fault conditions is present:
l zone 001 – 248 fault
l keypad 01 – 16 fault
l siren 01 – 16 fault
l repeater 01 – 08 fault
l fire trouble
l CO trouble
l gas trouble
l heat trouble
l freeze trouble
l probe disconnected trouble
l self test trouble
OFF: does not activate if a device fault condition is present.
10 – Device Low Battery
ON: activates if any of the following device low battery conditions is present:
- 96 -
l zone 001 – 248

l keypad 01 – 16
l siren 01 – 16
l repeater 01 – 08
l user 01 – 32 (wireless keys)
OFF: does not activate if a device low battery condition is present.
11 – Device Tamper
ON: activates if any of the following device tamper conditions is present:
l zone 001 – 248
l keypad 01 – 16
l siren 01 – 16
OFF – does not activate if a device tamper condition is present.
12 – RF Delinquency
ON: activates if any of the following RF delinquency troubles is detected:
l zone 001 – 248
l keypad 01 – 16
l siren 01 – 16
OFF – does not activate if an RF delinquency condition is present.
13 – Module Supervisory
ON – activates if any of the following module supervisory troubles is detected:
l HSM2HOST
l keypad 01 – 16
l zone expander 01 – 30
l HSM2204 1 – 4
l HSM2300 1 – 4
l HSM2208 01 – 16
l HSM3204CX
l HSM3408
l HSM3350
OFF – does not activate if a module supervisory trouble is detected.
14 – Module Tamper
ON – activates if any of the following module tamper conditions is present:
l HSM2HOST
l Keypad 01 – 16
l Zone expander 01 – 30
l HSM2204 1 – 4
l HSM2300 1 – 4
l HSM2208 01 – 16 tamper troubles
l HSM3204CX
l HSM3408
l HSM3350
OFF – does not activate if a module tamper condition is present.
15 – Communications
ON – activates if any of the following communications conditions is present:
l TLM trouble
l FTC receiver 1 – 4
l SIM Lock trouble
l Cellular Trouble
l Ethernet Trouble
l Receiver 1 – 4 absent
l Receiver 1 – 4 supervision trouble
- 97 -
l SMS Configuration trouble

l Alt comm. Fault.
OFF – does not activate if a communications trouble condition is present.
16 – Not Networked
ON – activates if any of the following not networked conditions is present:
l Zone 001 – 248
l Keypad 01 – 16
l Siren 01 – 16
l Repeater 01 – 08
l User 01 – 1000 (wireless keys) not networked troubles
OFF – does not activate if a not networked trouble condition is present.
156 – Latched System Event
OFF: activated during normal operation. Deactivated when triggered.
04 – Fire Alarm
ON: activates with fire alarm, [F] key, fire zones, 2-wire smoke.
OFF: does not activate with fire alarm.
05 – Panic Alarm
ON: activates on panic alarm (audible or silent).
OFF: does not activate on panic alarm.
06 – Burglary Alarm
ON: activates on burglary alarm.
OFF: does not activate on burglary alarm.
07 – Medical Alarm
ON: activates on medical alarm.
OFF: does not activate on medical alarm.
08 – Supervisory
ON: activates on supervisory alarm.
OFF: does not activate on supervisory alarm.
09 – Priority Event
ON: activates on priority alarm.
OFF: does not activate on priority alarm.
10 – Holdup
ON: activates on holdup alarm.
OFF: does not activate on Holdup alarm.
11 – Duress Alarm
ON: activates on duress alarm.
OFF: does not activate on duress alarm.
12 – Emergency Alarm
ON: activates on emergency alarm.
OFF: does not activate on emergency alarm.
13 – Fire Supervisory
ON: activates on fire supervisory alarm.
- 98 -
OFF: does not activate on fire supervisory alarm.

14 – Fire Trouble
ON: activates on fire trouble condition.
OFF: does not activate on fire trouble condition.
15– CO Alarm
ON: activates on CO alarm.
OFF: does not activate on CO alarm.
09 – System/Module Tampers
ON: activates when any module tamper condition occurs.
OFF: does not activate when any module tamper condition occurs.
10 – Zone Tampers
ON: activates when any zone tamper condition occurs.
OFF: does not activate when zone tamper conditions occur.
161 – DC Trouble
02 – PGM Timer
ON: output remains active until an access code is entered or certain criteria have been met, depending on the PGM
type.
OFF: output remains active until the PGM output timer expires.
09 – Battery Low
ON: activates when a low battery trouble occurs.
OFF: does not activate when a low battery trouble occurs.
10 – Battery Absent
ON: activates when a battery absent trouble occurs.
OFF: does not activate when a battery absent trouble occurs.
165 – Prox Used
01 – True Output/Latched Output
166 – Partition Prox Used
01 – True Output/Latched Output
175 – Bell Prog Access
- 99 -

200 - Zone Follower - Single Zone
02 – Timed Output
OFF: output remains active until the zone is restored.
04 – Latching
ON: output remains latched until a valid access code is entered or a valid Prox tag is presented.
OFF: output follows the setting of the Timed Output attribute.
05 – Follow Alarm
ON: output is activated on zone alarm and stays active until the bell is turned off. See table for operation with bits 2
and 4.
OFF: output is activated on zone opening and deactivated when zone is closed.
Timed Output Latching Follow Alarm PGM Output
OFF OFF OFF ON upon zone opening (including tamper and fault), OFF upon zone closing
OFF OFF ON ON upon zone alarm, OFF upon bell cut-off or alarm silenced
OFF ON OFF ON upon zone opening, OFF upon valid code
OFF ON ON ON upon zone alarm, OFF upon valid code
ON OFF OFF ON upon zone opening, OFF upon PGM timer expires
ON OFF ON ON upon zone alarm, OFF upon PGM timer expires
ON ON OFF ON upon zone opening, OFF upon valid code
ON ON ON ON upon zone alarm, OFF upon valid code
201 – 231 Zone Follower Zones 1-248
02 – Timed Output
09-16 – Zone Terminals 1-8
ON: zones associated with terminals 1-8 are enabled for zone follower operation.
OFF: zones are not enabled for zone follower operation.
[011] PGM Configuration Options

This section is used to configure PGM types that offer multiple options.
[001]-[324] Select PGM
The following options may be selected for each PGM:
- 100 -
Zone Follow PGM By Zone

This option is used to specify the zone that PGM type 200 follows. Enter 001-248 to select zone 1-248.
Proximity Tag Used
This option is used to define which proximity tag will activate PGM outputs programmed as [165] Prox Used. Enter 000 to
enable this PGM attribute for all user proximity tags, or enter user number 0002-1000 to have this attribute activated by a spe-
cific user proximity tag.
Command Output 1-4
This option is used to assign a schedule, programmed in section [601]-[604], for PGM Types 166 and 121-128 to follow. Pro-
gram 001-004 to for schedules 1-4. Program 000 to activate the PGM when a proximity tag is presented.
[012] System Lockout

Keypad Lockout – Number of Invalid Local Attempts
This option controls the number of invalid access code entries allowed before the keypad is locked.
When keypad lockout occurs, the system is inaccessible by keypad for the programmed duration. If the number of invalid
attempts is not reached within one hour, or if a valid access code is entered, the counter is reset to 0. Valid entries are 000 to
255 minutes. Entering 000 disables the feature. Presenting an invalid tag counts toward keypad lockout.
Note: For EN 50131 certified installations, maximum number of attempts is 10.
Keypad Lockout Duration
This programming option determines the length of time the keypad is locked out for. If the system cold starts while in keypad
lockout, the lockout is removed. Valid entries are 000 to 255 minutes. Entering 000 disables keypad lockout.
EN Note: For EN 50131 certified installations, minimum of duration is 90 s.
Remote Lockout DLS
This programming option determines the number of invalid access code entries allowed via SMS or DLS before remote
access is locked out for the programmed duration (see below). If the number of invalid attempts is not reached within one
hour, or if a valid access code is entered through SMS or DLS, the counter is reset to 0. The valid entries are 003 to 255
attempts. Default is 6 attempts. The number of invalid attempts is fixed at 5 when using System Administrator Software and
the lockout duration is 1 hour.
EN Note: DLS tries to connect using the programmed DLS Access code first and, if unsuccessful, using the default DLS access
code. Two failed attempts are counted if both codes are incorrect.
Remote Lockout Duration
This programming option determines how long the remote lockout lasts. If the system cold starts while in remote lockout, the
lockout restarts for the programmed duration. Valid entries are 001 to 255 minutes. Entering 000 disables remote lockout.
System Options
[013] System Option 1
1 – NC Loop/EOL
ON: All zones are wired as normally closed circuits with returns connected to a COM terminal. The end-of-line resistor is not
required. An alarm is generated when the circuit is opened.
OFF: All zones must be wired with an end-of-line resistor configuration, determined by option 2 below.
Note: The valid EOL value is 5600 Ohms (5.6KΩ).
2 – DEOL/SEOL
ON: All zones use Double-End-of-Line resistors, except Standard Fire, Delayed Fire, Auto-Verified Fire, Co and Supervisory
zone types. DEOL resistors enable detection of zone faults and tampers. The tamper resistor (5.6KΩ) is placed in parallel
across the alarm activating device, and the single EOL resistor (5.6KΩ) is placed between the alarm and tamper contacts.
This allows detection of zone faults (shorted zone), tampers (open zone), alarms (11.2KΩ), and restored zones (5.6KΩ).
- 101 -
If the zone is disarmed and placed in the tamper or fault state, trouble beeps sound on all system keypads until a key is
pressed on each partition. A zone tamper is sent to the monitoring station if programmed. If the zone is armed and a tamper
is activated, the tamper alarm and zone alarm are logged and transmitted.
OFF: All zones must have a 5.6KΩ resistor. If the zone is shorted or open, it is in the tripped state. If the zone is open and pro-
grammed as a fire zone, it is in the trouble state. The EOL and DEOL zone attributes override this system option.
Note: Zone Faults (Supervisories) on wireless zones do not cause an audible alarm while armed.
3 – Show All Troubles When Armed
ON: The Trouble LED illuminates when troubles are present on the system in both the armed and disarmed state.
OFF: The Trouble LED illuminates for all troubles while disarmed, but only for Fire Troubles while armed.
4 – Tamper/Faults Do Not Show As Open
ON: The zone does not show open if the zone is in the tamper or fault states. Only the Trouble LED illuminates.
OFF: The respective zone LED shows open if the zone is in the tamper or fault states. The Trouble LED also illuminates.
5 – Auto-Arm Schedule in [*][6]
ON: The auto-arm schedules ([151] - [158]) are accessible via [*][6] as well as Installer Programming.
OFF: The auto-arm schedules ([151] - [158]) are only accessible to installers via Installer Programming.
Note: This toggle controls access for all eight partitions.
6 – Audible Exit Fault
ON: If a delay type zone is violated after the exit delay has expired, an entry delay warning is sounded through the keypad
and siren indicating that an improper exit was made. If the alarm system is disarmed within the entry delay period no signal
is sent.
OFF: The entry delay warning is sounded only through the keypad.
7 – Event Buffer Follows Swinger
ON: Once an event reaches its swinger shutdown limit programmed in "[377] Communication Variables" on page 123, it will
no longer log events to the event buffer until the swinger shutdown is reset. This avoids filling the event buffer with false
events.
OFF: The event buffer continues to log events to the buffer even after the event has gone into swinger shutdown.
8 – Temporal Three Fire Signaling
ON: All fire bells sound in the temporal three pattern. Cadence is as follows: (500ms ON, 500ms OFF, 500ms ON, 500ms
OFF, 500ms ON, 1.5 sec. OFF).
OFF: All fire bells will sound with the standard 1 second on/1 second off fire bell cadence.
Note: Must be on for UL/ULC installations.
1 – Bell Squawk
ON: The siren emits a single squawk when armed in any manner, including Auto-arm, and a double squawk when disarmed.
When the system is disarmed, the siren emits a series of three squawk pairs to indicate alarms in memory.
OFF: The siren does not squawk when arming or disarming.
NA Note: For UL/ULC, must be enabled if wireless keys are used with the alarm system.
2 – Bell Squawk on Auto-Arm
ON: The siren squawks once every 10 seconds during the auto-arm pre-alert time.
OFF: The siren does not squawk during auto-arm pre-alert.
3 – Bell Squawk On Exit
ON: The siren squawks once per second during exit delay, changing to 3 squawks per second for the final 10 seconds.
OFF: The siren does not squawk for exit delay conditions.
4 – Bell Squawk On Entry
ON: The siren pulses with the same timing as the keypad buzzer during entry delay, changing to 3 squawks per second for
the final 10 seconds.
OFF: The siren does not activate during entry delay.
- 102 -
5 – Bell Squawk On Trouble

ON: When a trouble condition exists on the system, the siren squawks 2 times every 10 seconds (as per the keypad buzzer).
The siren is silenced when the keypad beeps are silenced (any key pressed on keypad).
OFF: The siren does not activate with a trouble condition.
6 – Reserved
7 – Exit Delay Termination
ON: The exit delay is reduced to 5 seconds once a Delay 1 zone is restored. Force-Arm Delay 1 type zones also end the exit
delay.
OFF: The exit delay timer continues to count even after the delay zone is restored.
All audible options associated with the exit delay function are silenced until the time programmed for the exit delay has
elapsed.
8 – Fire Bell Continues
ON: For all Fire type alarms, the siren sounds until an access code is entered to silence the alarm or disarm the system
regardless of the time programmed for bell timeout.
OFF: For all Fire type alarms, the siren sounds for the length of Bell Timeout or until an access code is entered.
ULC Note: Must be disabled for ULC installations.
1 – [F] Key Enabled
ON: Pressing and holding the [F] key for 2 seconds triggers a Fire alarm.
OFF: The [F] key does not sound or report an alarm when pressed.
Note: Use only for residential fire installations.
2 – [P] Key Audible
ON: When a valid [P] key alarm is generated, the keypad buzzer emits a series of 3 beeps to acknowledge the alarm and the
siren sounds for the length of bell timeout.
OFF: When a valid [P] key alarm is generated, the keypad buzzer and the siren are silent, but the alarm is still transmitted (if
programmed).
Note: Fire, Medical, and Panic key transmissions follow the partition 1 alarm/restore call direction options (Fire, Medical, and
Panic key). The Fire, Medical, Panic keys operate even if keypad blanking and keypad lockout are active.
3 – Quick Exit
ON: When the system is armed, users may enter the [*][0] command to temporarily bypass a single Delay 1 or Delay 2 zone
to exit the premises. Only one delay zone may be activated. Activity on another delay zone initiates the appropriate alarm
sequence. If the delay zone is still open two minutes after the [*][0] command is entered, entry delay is initiated. If armed in
the Stay mode, the automatic bypass on Stay/Away zones remains.
OFF: When the system is armed, users can not perform a quick exit using [*][0].
4 – Quick Arming /Function Key
ON: [*][0] arming and Stay/Away function keys may be used to arm the system without the entry of a valid access code.
OFF: [*][0] arming is not permitted. All arming functions require the entry of an access code to activate (including Stay/Away
keys).
5 – Reserved
6 – Master Code Not User Changeable
ON: The master code (access code 01) may not be changed by the user and may only be programmed in Installer Pro-
gramming.
OFF: The master code may be programmed by the user using the [*][5][Master Code] command. The master code may also
be programmed in Installer Programming.
7 – Telephone Line Monitor Enable
ON: The TLM function is active and the system indicates a trouble condition when using the [*][2] View Trouble Conditions
command.
OFF: The TLM function is deactivated and telephone line troubles are not indicated by the system.
- 103 -
NA Note: Must be ON for UL/ULC listed installations.

8 – Telephone Line Monitor Audible When Armed
ON: When the system is disarmed, a telephone line monitor trouble generates a trouble indication as described above. If the
system is armed, a telephone line monitor trouble generates an audible alarm on the siren for the duration programmed for
bell timeout or until an access code is entered to disarm.
OFF: Telephone line troubles generate a trouble indication, the Trouble LED illuminates, and the keypad buzzer beeps until
a key is pressed.
1 – AC Trouble Display
ON: If AC power fails, the condition is reported to the monitoring station and is indicated as a trouble condition on the system
keypads.
OFF: If AC power fails, the condition is reported, but the Trouble light on the system keypads is off. The trouble is displayed in
[*][2].
NA Note: Must be ON for UL/ULC listed installations.
2 – AC Trouble Light Flashes
ON: When AC power is lost, the Trouble light flashes in the base “Ready” and “Armed” mode within 30 seconds of power
loss. When AC restores, the Trouble light stops flashing within 30 seconds. If enabled, this option overrides the AC display
option.
OFF: When AC power is lost, the Trouble light illuminates but does not flash.
3 – Keypad Blanking
ON: If no keys are pressed within 30 seconds, all keypad lights except backlighting (if enabled) are shut off until the next
keypress, entry delay, audible alarm or keypad buzzer condition.
Keypad function keys still operate when the keypad is blank, unless the function key is programmed to require an access
code. Keypad Blanking While Armed overrides this feature. When a partition is armed and in alarm, entering a code to
remove blanking silences the alarm and disarms the system.
OFF: The keypad lights remain ON at all times.
4 – Keypad Blanking Requires Code
ON: A valid access code must be entered before a blanked keypad can be used. Information becomes inaccessible to level
1 users.
OFF: Pressing any key on a blanked keypad removes keypad blanking.
CP-01 Note: Keypad Blanking Requires Code must be set to off for CP-01 listed installations.
5 – Keypad Backlighting
ON: All keypads on the system have backlighting on at all times.
OFF: All keypads on the system have backlighting off.
6 – Power Save Mode
ON: If AC power fails, all keypad lights including backlighting are shut OFF. The keypad lights come back ON after a
keypress, entry delay, audible alarm or keypad buzzer condition (except door chime). Keypad lights return to the off state
after 30 seconds of inactivity.
OFF: If AC power fails, keypads do not go into power save mode.
7 – Bypass Display When Armed
ON: The Bypass message is displayed if zones are bypassed when the system is armed.
OFF: The Bypass message is displayed only while the system is disarmed to indicate that zones on the system are
bypassed. When the system is armed, the Bypass light is off.
The Bypass message is displayed if Stay/Away zones are auto bypassed at the time of arming regardless of whether or not
this option is enabled. This option only enables and disables manual bypass message display.
8 – Keypad Tampers Enabled
ON: All keypads containing tamper switches generate tamper alarms and restores.
- 104 -
OFF: The tamper switches on all keypads do not generate tamper alarms.
Note: If this option is used, all keypads should be properly installed and secured (tamper restored) before enabling the
option.
NA Note: Must be ON for UL/ULC commercial burglary listed installations.
1 – Chime on Opening
ON: When a zone with the door chime attribute ON is opened, the system keypads and sirens (if enabled) beep.
OFF: When a zone with the door chime attribute ON is opened, the system keypads and sirens (if enabled) do not beep.
2 – Chime on Closing
ON: When a zone with the door chime attribute ON is closed, the system keypads and sirens (if enabled) beep.
OFF: When a zone with the door chime attribute ON is closed, the system keypads and sirens (if enabled) do not beep.
3 – RF Jam Trouble Beeps
ON: Trouble beeps sound when an RF Jam Trouble is detected
OFF: Trouble beeps do not sound when an RF Jam Trouble is detected
4 – Multi Hit
ON: Alarms from the same zone within the Burglary Verification Timer duration cause the police code or burglary verified to
be logged and transmitted. The number of zone trips required to create a confirmed alarm depends on the value of the pro-
grammable burglary verification counter.
OFF: Alarms from the same zone within the Burglary Verification Timer duration do not cause the police code or burglary veri-
fied to be logged and transmitted.
Note: This feature only applies to zones defined as Interior, Interior Delay, Interior Stay/Away, Instant Stay/Away, Delay
Stay/Away, or Night Zones (PIR Zones). Do enable this option if section [380], option 2 - Restore on Bell Time Out is
enabled.
5 – Late to Close
ON: Provides an audible warning if the alarm system has not been armed by a programmed time of day but does not arm the
alarm system. The alarm system communicates and logs a Late to Close event at the end of the Auto-arm/Postpone pre-alert
for each partition.
OFF: The alarm system will neither communicate nor log a Late to Close event at the time programmed for Auto-arm for each
partition.
Note: If the Auto-arm toggle option is disabled, the Auto-arm Pre-alert still occurs when a time is programmed for that day (if
enabled) and the event is logged and communicated. This option does not directly affect the functionality of Auto-arm. If Late
to Close is enabled and Auto-arming is not, LCD keypads display “System Arming in Progress” during the Late to Close Pre-
alert.
6 – Daylight Savings Time
ON: The alarm system adjusts between Daylight and Standard times according to the times programmed in System Timers
([005] options 901-902).
Note: Auto-arm and Test Transmissions should not be attempted between 0200 and 0300 hours, as they will be missed dur-
ing a daylight savings clock adjust. Events programmed to occur between 0100 and 0200 will occur twice during a daylight
savings clock adjust. Daylight Savings Time programming should not conflict with the Auto-arm and Test Transmissions pro-
gramming.
OFF: The alarm system makes no automatic time adjustments for Daylight Saving time.
7 – Silence Chime During Quick Exit Delay
ON: Door chime does not sound during quick exit.
OFF: Door chime sounds during quick exit, according to zone settings.
8 – Bell Squawk on Away Arm/ Disarm Only
ON: Bell Squawks are only heard when away arming, as well as when disarming from Away mode. This feature prevents the
siren from activating when arming in stay and night modes.
OFF: Bell Squawks are heard during all types of arming and disarming.
- 105 -
Note: This option follows the “Bell Squawk Attribute” features if they are enabled.
1 – Test Transmission Exception
ON: The alarm system does not send a test transmission if a transmission was sent to the receiver within the programmed
interval as set in section [377]>See "[003] – Periodic Test Transmission Cycle" on page 125.
OFF: Test transmissions are always sent at the programmed interval.
2 – Real-Time Bypass Reporting
ON: When a non-24-hour zone is bypassed in [*][1], the system immediately logs and communicates the bypass status of the
zone.
Global Zones: 24-hour and non-24 hour zone bypasses are logged and communicated in real time. Non-24 hour zone unby-
pass events are generated when the last assigned partition is disarmed.
OFF: When a non 24-hour zone is bypassed in [*][1], the system logs and communicates the bypass status of the zone only
after the partition is armed. This option is applied regardless of how zones are bypassed in [*][1], recall bypass group, clear
all bypasses, bypass open zones, bypass recall as well as other methods such as bypassing via ITv2 or DLS.
Global Zones: 24-hour zone bypasses are logged and communicated in real time. Non 24-hour zone bypass events are
logged and communicated when armed. Non 24-hour zone unbypass events are logged and communicated when the par-
tition is disarmed.
3 – Armed Status PGM ON at End of Exit Delay
ON: PGMs are activated at the end of exit delay. This applies to PGMs with one of the following armed status attributes:
l 115 System Armed Status PGM
l 116 Away Armed Status PGM
l 117 Stay Armed Status PGM
l 120 Away Armed with No Zone Bypass Status
l 129 Partition Status Alarm Memory
OFF: PGMs are activated at the beginning of exit delay. This applies to PGMs with one of the armed status attributes listed
above.
4 – Auto Bypass Report
ON: All Night or Stay/Away type zones that are auto-bypassed when arming in Night or Stay mode log and report Zone
Bypass. When disarming, all auto-bypassed Night or Stay/Away zones log and report Zone Un-Bypassed. All manually
bypassed zones continue to log and report.
OFF: All Night or Stay/Away type zones that are auto-bypassed when arming in Night or Stay mode do not log or report Zone
Bypass. When disarming, all auto-bypassed Night or Stay/Away zones do not log and report Zone Un-Bypassed. All manu-
ally bypassed zones continue to log and report.
5 – Keypad Buzzer Follows Bell
ON: The keypad buzzer activates with all bell activity for the selected partition.
OFF: The keypad buzzer only activates with alarms programmed to do so.
7 – Exit Delay Restart
ON: Opening a delay zone door after it has already been opened and closed during an exit delay restarts the exit delay
timer. Further openings and closings do not restart the timer.
OFF: Delay zone openings and closings do not restart the exit delay.
8 – AC Fail Trouble Beeps
ON: System keypads beep when an AC trouble event occurs.
OFF: System keypads are silent during AC troubles.
6 – Reserved
1 – Audible Wireless Device Fault
ON: If a wireless zone fault occurs while armed, the siren sounds for the duration of Bell Time Out. This option only affects
zone definitions that are considered armed. The following zone types do not generate an alarm when faulted while stay
armed: interior stay away zone, delay stay away zone, instant stay away zone, night zone. The following zone types do not
- 106 -
generate an audible alarm in any armed state (stay, away, or night): 24-hour supervisory, 24-hour non-alarm, 24-hour CO,
delayed 24-hour Fire, standard 24-hour fire, Auto-verified fire.
When the partition is armed, wireless supervisory troubles from sirens, keypads and repeaters generate audible alarm con-
ditions.
If Tamper/Fault Detection is enabled, these events can start the burglary verified timer and affect the burglary verified
counter.
OFF: Wireless device faults do not sound the siren.
2 – Latching Troubles
ON: Troubles remain on the system until viewed via [*][2], even if they are restored. The trouble condition is cleared when
the"Press (*) to Acknowledge" option is selected within the [*][2] menu after the trouble has restored. The Trouble LED turns
off unless other troubles are present. The trouble is not cleared if the [*][2] menu times out before the [#] key is pressed.
OFF: Troubles are cleared once restored.
3 – Reserved
4 – Reserved
5 – Audible Bus Fault
ON: All module supervisory trouble conditions activate the siren.
OFF: Only zone expander supervisory trouble conditions while armed activate the siren.
6 – Duress Codes
UK
ON: The duress code attribute can be enabled/disabled from the [*][5] menu. For BS8243 installations the default is off.
OFF: The duress code attribute is not programmable from the [*][5] menu.
7 – Temperature in Celsius
ON: Temperature is displayed in Celsius on LCD keypads.
OFF: Temperature is displayed in Fahrenheit on LCD keypads.
8 – Reset After Zone Activation
ON: Only a police code\sequential detection alarm requires a remote reset once the partition has been disarmed.
OFF: Any burglary alarm requires a remote reset once the partition has been disarmed.
1 – Access Code Entry During Entry Delay
ON: During entry delay the alarm system can only be disarmed using a keyswitch or proximity tag. When the siren is active
an access code can still be used to disarm the system.
OFF: An access code can be used to disarm the system during entry delay.
EN 2 – EU Entry Procedure
ON: If an alarm occurs on a zone when entry delay is not active, the siren activates and the alarm is communicated imme-
diately, depending on the zone type tripped.
When entry delay is active, all burglary type alarms activate the siren, but communication of the alarm is delayed by 30
seconds. When entry delay expires, the alarm is not communicated unless the siren has been active for at least 30 seconds.
Police code is not generated as a result of alarms triggered during entry delay, although the Burglary Verification Timer
starts after entry delay and the 30-second communication delay expire.
This feature is only active when the partition is armed.
OFF: Burglary alarms that occur during entry delay activate the siren and are communicated immediately. Two exceptions
are if the bell delay timer is programmed and if transmission delay is enabled for the zone in alarm. In both cases, the alarm
follows the timer.
3 – [*][8] Access While Armed
ON: This option ensures [*][8] installer programming is accessible from a keypad on a disarmed partition while other par-
titions on the system are still armed.
Note: For UL listed installations, this option must be disabled.
- 107 -
OFF: [*][8] installer programming is not available when any partition on the system is armed. All partitions must be disarmed
and the siren must be off before [*][8] is accessible.
UK 4 – Remote Reset
ON: If an alarm occurs on a burglary zone, the system is locked out after disarming. It remains locked until a 5-digit reset
code, provided by the installer/central station, is keyed in. If a duress code is used to disarm the partition, the system is not
locked out.
In the disarmed state, only Audible 24 Hour Burglary zones, Audible 24 Hour Latching Tamper zones, and Audible 24 Hour
zone on PGM 2 cause lockout.
To obtain the reset code, the user must provide a corresponding system lock code, displayed on the keypad when one of the
following conditions occurs:
l the system has been disarmed (Duress Code excluded)
l the bell has timed out (24Hr zones)
l an access code has been entered (24Hr zones)
On an LCD keypad, the message “REMOTE RESET RQD” is displayed on the top line and “CODE” along with the actual
code is displayed across the bottom line..
While the system is locked out, the only options available are [*][3], [*][6], [*][7], and [*][8]. Accessing [*][8] Installer Pro-
gramming unlocks the alarm system. The system continues to function (alarms, tampers, etc) while the system is locked out.
Lock out follows both transmission and bell delays.
OFF: The system is not locked out after an alarm occurs.
EN 5 – Engineer’s Reset (EU)
ON: If the alarm system has gone into alarm during the previous armed period, or if a 24-hour alarm has occurred (armed or
disarmed), the system cannot be armed (Ready light OFF) until Installer Programming is entered or Engineer’s Reset is per-
formed via DLS. “Reset Required” is displayed on the keypad. This feature applies to tampers and faults in both armed and
disarmed states and does not apply to module tampers, system supervisories, zone expander alarms or PGM 2 input alarms.
Note: If Engineer’s Reset is triggered during exit delay, the system still arms. Troubles cannot be overridden while Engin-
eer’s Reset is enabled.
OFF: The system does not require Engineer’s Reset or to be placed into Installer Programming in order to arm the alarm sys-
tem after an alarm.
6 – Keyswitch Disarming During Entry Delay
ON: Keyswitches, proximity tags and wireless keys disarm the alarm system only if an entry delay is active.
OFF: Keyswitches, proximity tags and wireless keys disarm the alarm system regardless of entry delay.
Note:Do not enable with option in conjunction with [040] Prox and Code.
EN 7 – Installer Access and DLS
ON: The user must enter [*][6][access code][05] before the installer can access Installer Programming by DLS or via the
keypad ([*][8]).
Installer Programming remains accessible for 6 hours, during which time the installer can enter/exit or connect with DLS an
unlimited number of times.
OFF: The installer can access Installer Programming without the user entering [*][6].
EN 8 – Troubles Inhibit Arming
ON: The following troubles prevent arming until restored:
l Tampers on the alarm system, modules and zones
l Corbus troubles
l AC troubles on the alarm system and modules
l Battery troubles on the alarm system, modules and zones
l Transmission troubles (FTC, TLM, GPRS, Ethernet)
l Bell troubles
The alarm system can still be armed if troubles are overridden. To perform a trouble override, while in the Trouble Menu ([*]
[2]), scroll right or left and press [*] when Trouble Acknowledgment is displayed on the keypad. Alternatively, press the [9][9]
key to acknowledge and override the existing troubles.
To override open zones, faulted zones or tampered zones use the Zone Bypass feature.
- 108 -
OFF: The system can be armed even when troubles are present.
Note: When Engineer’s Reset is on, trouble conditions cannot be overridden. Zone Expander supervisory troubles cannot
be acknowledged and overridden. These conditions must be restored before the panel can be armed.
Note: When [024][3] is enabled, AC/DC Inhibit Arming, the AC or DC trouble must be restored before the system can be
armed.
EN 1 – Trouble Display
ON: If the panel is both armed and keypad blanking is active, when a trouble is present the keypad trouble LED will remain
off . When the system is disarmed, or if blanking is removed, the trouble LED will be active if a trouble is present.
OFF: The trouble LED will turn off when keypad blanking is active in armed or disarmed state.
EN 2 – Keypad Blanking while Armed
ON: If [016][3] is disabled within 30 seconds after the exit delay terminates, the keypad blanks (no indicator lights).
OFF:The keypad blanks when the system is armed or disarmed.
Note: For systems compliant with EN50131-1 and EN50131-3, option [021] bit 2 “Keypad blanking while armed” must be
ON.
3 – Reserved
4 – Ready Display
ON: The keypad ready LED will continue to show system ready status while keypad blanking is active.
OFF: The keypad ready LED will turn off when keypad blanking is active.
5 – PGM Blanking
This feature is meant to be used in conjunction with the keypad blanking while armed feature.
EN ON:This feature is necessary to comply with EN50131-1:2006.
When the system enters blanking mode, any PGMs programmed as Armed Status, Ready Status, Away Armed Status, or
Stay Armed Status will de-activate. If blanking is cleared by pressing a key, or entering an access code depending on how
the panel is configured, these PGMs must re-activate if they would have normally been ON if blanking was disabled.
OFF: When the system enters blanking mode, any PGMs programmed as Armed Status, Ready Status, Away Armed Status,
Stay Armed Status) operate normally.
6 – Armed Display
ON: The keypad armed LED will continue to show Armed status while keypad blanking is active.
OFF: The keypad armed LED will turn off when keypad blanking is active.
7 – Open Zones Cancels Arming
ON: The system cannot be armed while zones are open unless the zones are bypassed using [*][1]. In order to bypass open
zones, the bypass attribute needs to be enabled for the zone.
OFF: Open zones do not prevent arming.
8 – Audible Exit Delay for Stay Arming
ON: When the system is armed in Stay mode the exit delay is sounded by 1 beep every 3 seconds.
OFF: When the system is armed in Stay mode the exit delay is silent.
1 – [F] Key Option
ON: When the [F] key is pressed, acknowledge beeps are only emitted from the keypad. The siren does not sound fire alarm.
OFF: [F] key acknowledgment beeps are emitted from the keypad and sounds for fire alarm.
2 – Reserved
3 – Reserved
EN 4 – Transmission Counter in Hours
ON: The alarm system sends a test transmission after the programmed number of hours in the test transmission cycle (Sec-
tion [377], Option 003).
OFF: The alarm system sends a test transmission after the programmed number of days.
- 109 -
Note: This option must be set to OFF for UL installations.

5 – Away to Stay Toggle
ON: The alarm system cannot be switched from Away to Stay mode by pressing the [Stay] function key.
OFF: The alarm system can be switched from Away to Stay mode by pressing the [Stay] function key.
6 – 2-Way Audio Disconnect
ON: The system does not disconnect the 2-way audio session if a new event needs to be communicated.
Note: This option applies to new alarm events only. All non-alarm events (except Fire Troubles) are communicated after the
2-Way session has ended.
OFF: The system disconnects the 2-way audio session if a new event occurs.
7 – Trouble Beeps are Silent
ON: When a trouble is detected on the system, trouble beeps are not sounded at the keypad with the exception of Fire
troubles.
OFF: When a trouble is detected on the system, trouble beeps are sounded at the keypad.
Note: This option must be OFF for UL Residential Fire applications.
Note: To silence the Fire Trouble beep, press [*][2] and exit. Accessing [*][2] requires a valid user code.
8 – Keyswitch Arms in Away Mode
ON: Keyswitch arming arms the alarm system in away mode.
OFF: Keyswitches only arm the system in away mode if an entry/exit zone is violated during exit delay.
Note : Proximity tag arming follows this section.
1 – Ready LED Flashes for Force Arm
ON: If a force arm capable zone is tripped, partition keypads flash the ready LED in the disarmed state instead of illuminating
it steadily. If a non-force arm capable zone is tripped, the ready LED turns off.
OFF: If a force arm capable zone is tripped, the Ready LED is illuminated steadily. If a non-force arm capable zone is tripped,
the Ready LED turns off.
2 – Access Code Required for [*][*]
ON: When using the [*][*] Temperature Display Menu command, an access code must be input before the temperature menu
can be viewed.
OFF: An access code is not required to view the temperature menu using [*][*].
EN 3 – Tamper/Fault Detection
ON: The following trouble conditions, when configured to generate audible alarm conditions, will contribute to a burglary veri-
fication sequence when sequential detection is used. When enabled, a bell circuit trouble will also generate an audible
alarm condition using other sirens that assigned to the partition.
l TLM trouble
l Bell circuit trouble
l Zone fault
l Module supervisory trouble
l Alternate Communicator fault
l Ethernet Trouble
l Zone Mask Fault
OFF: Trouble conditions are displayed and processed as standard operation.
Note: This option applies to the Sequential Detection feature only.
EN 4 – Access Code Required for [*][1]
ON: When using the [*][1] Bypass Zones command, an access code must be input before zones are bypassed.
OFF: An access code is not required to bypass zones using [*][1].
ON: When using the [*][2] View Troubles command, an access code must be input before system troubles can be viewed.
OFF: An access code is not required to view troubles using [*][2].
- 110 -
Note: For UL Residential installations, ensure the access code requirement is set to ON.
ON: When using the [*][3] View Alarms in Memory command, an access code must be input before the alarm memory can be
viewed.
OFF: An access code is not required to view alarms in memory using [*][3].
7 – Access Code Required for [*][4]
ON: When using the [*][4] Chimes command, an access code must be input before chimes can be toggled on and off.
OFF: An access code is not required to toggle chimes using [*][4].
8 – [*][6] Accessibility
ON: All user codes provide access to the [*][6] menu.
OFF: Only the master code provides access to the [*][6] menu.
1 – Reserved
2 – Reserved
EN 3 – AC/DC Inhibits Arming
ON: The system cannot be armed when an AC or battery trouble is present. This includes keypad, keyswitch, automatic, and
DLS arming. An error tone is generated if the user attempts to arm the system during an AC/DC trouble.
Note: Displaying AC troubles ([016] option 2) is strongly recommended if this option is enabled.
OFF: The system can be armed, regardless of the presence of an AC or DC trouble and does not check the system battery
upon arming.
EN 4 – Tampers Inhibit Arming
ON: The following conditions trigger Tampers Inhibit Arming:
l Faults on the zones, modules
l Tampers on the zones, modules
l Bell circuit trouble
l Communications fault troubles (TLM, FTC, Radio/Sim card failure, ethernet trouble, communicator fault)
l Warm start troubles
Tampers must be restored through Installer Programming before the system can be armed (including no-activity and key-
switch arming). Reset Required displays on the keypad.
When this option is enabled, manual zone bypassing does not bypass the tamper or fault states (DEOL). This feature also
applies to zone faults.
OFF: Tamper troubles do not latch and do not prevent arming.
5 – Real time Clock
ON: If enabled, the panel will set the time and date automatically provided by either the on board Ethernet or the cellular com-
municator at 4:05pm.
OFF: If disabled, the system time and date needs to be manually programmed
Note: The time zone of the panel must be set in [851][020] and the Ethernet or Cellular communication must be com-
municating to a System 5 Surgard receiver.
6 – Reserved
7 – Reserved
8 – DLS Disconnect
ON: All events except Periodic Test Transmission, Periodic Test with Trouble, and System Test are considered priority
events. If DLS is active when an event occurs, the alarm system immediately terminates the connection in order to com-
municate the new events.
OFF: Only the following alarm type events terminate a DLS session:
l Zone alarms
l FMP key alarms
l Duress alarms
- 111 -
l Zone expander supervisory alarms

l 2-wire smoke alarms
1 – European Dial
ON: Pulse dialing make/break ratio is 33/67.
OFF: Pulse dialing make/break ratio is 40/60.
2 – Force Dial
ON: The system dials the central station phone number even if no dial tone is present. The process is as follows:
1. Dial programmed phone number.
2. If no dial tone detected, terminate call.
3. Search for dial tone for 5 seconds.
4. If no dial tone detected, hang up for 20 seconds.
5. Search for dial tone for 5 seconds.
6. If no dial tone detected, dial anyway.
OFF: No attempt is made to contact the central station if dial tone is not present.
UL Note: Force Dial must be enabled for UL installations.
3 – Test Transmission Counter in Minutes
ON – When the option is on, the Periodic Test Transmission interval programmed in section [377][003] will be 000-255
minutes instead of 000-255 days or hours.
OFF – When the option is off, the Periodic Test Transmission interval programmed in section [377][003] will be 000-255
days, or hours if option 4 in section [022] is enabled.
Note: This value must be set to OFF for UL installations.
EN 4 – Warm Start Indication

ON - Warm Start trouble is logged and indicated in the [*][2] Troubles Menu.
OFF: Warm Start trouble is a log only event.
5 – I.D. Tone
ON: After the telephone number is dialed, the alarm system emits a tone (as specified by I.D. Tone Frequency option) for
500ms every two seconds to indicate that a digital equipment call is in progress.
OFF: I.D. tone is disabled.
6 – Tone Generated-2100Hz
ON: 2100 Hz I.D. tone.
OFF: 1300 Hz I.D. tone.
7 – DLS Window
ON: When DLS access is enabled ([*][6] option 5 ON), Installer Programming is accessible through DLS or the [*][8] menu
only once during a 30 minute window.
OFF: When DLS access is enabled, Installer Programming is accessible through DLS or the [*][8] menu an unlimited number
of times during a 6-hour window.
8 – FTC Audible Bell
ON: If a Failure to Communicate trouble is generated while the system is armed, the siren activates for the length of bell time-
out or until the system is disarmed.
OFF: If a Failure to Communicate trouble is generated while the alarm system is armed, the siren does not activate but the
keypad buzzer emits trouble beeps until a key is pressed.
[040] User Authentication
This feature enables the installer or master user to select one of two user authentication methods:
01 – User Code or Proximity Tag
The user can access the system by entering a valid code or by presenting a proximity tag.
- 112 -
02 – User Code and Proximity Tag

The user must enter a valid code and present a proximity tag whenever the system prompts for an access code. A proximity
tag is not required to enter [*][8] Installer Programming.
Note: When this option is enabled, the proximity tag and code must belong to the same user.
[041] Access Code Digits
00 – 4-Digit Access Codes
Access codes are 4 digits long.
EN 01 – 6-Digit Access Codes
Note: This setting is required for EN50131-1 compliant installations using more than 100 access codes.
02 – 8-Digit Access Codes
Note: This setting is required for EN50131-1 compliant installations using 1000 access codes.
[042] Verified Events
Burglary Verified Counter
This counter determines the number of burglary alarms that must occur within the Burglary verification window before a con-
firmed Burglary Verified alarm is logged and communicated. Zones with the burglary verification zone attribute enabled con-
tribute to the generation of a confirmed Burglary Verified alarm in conjunction with this counter and the burglary verification
timer.
Holdup Verification Counter
This counter determines the number of alarms that must occur within the Holdup verification window before a confirmed Hol-
dup alarm is logged and communicated. Zones with the holdup verification zone attribute enabled contribute to the gen-
eration of a confirmed Holdup alarm in conjunction with this counter and the holdup verification timer.
Burglary Verification Selection
Use this section to select one of the following burglary verification timer modes:
Mode Description
001 Police Code The burglary verification timer operates in minutes.
002 Cross Zoning The burglary verification timer operates in seconds. The first alarm in the sequence does not log or communicate the
alarm or activate the bell.
003 Sequential The burglary verification timer operates in minutes. The first alarm in the sequence causes an audible bell.
Detection
Partition Setup
[151]-[158] Partition Auto-Arm/Disarm
Enter section 151 to 158 for partition 1 to 8 auto-arm/disarm configuration.
[001] – Partition Auto-Arming Times
Use this section to program the time of day a partition is automatically armed. A different auto-arming time can be pro-
grammed for each day of the week from Sunday to Saturday. Time is in 24-hour format (HH:MM) and valid entries are from
00:00 to 23:59.
Conditions that cancel auto-arming if enabled:
l Open zones (depending on the settings of the zone)
l AC/DC troubles
l System troubles
l Any valid disarming procedure - proximity tag, access code, disarm key, etc.
[002] – Partition Auto-Disarm Times
Use this section to program the time of day a partition is disarmed. A different auto-disarming time can be programmed for
each day of the week from Sunday to Saturday. Time is in 24-hour format (HH:MM) and valid entries are from 00:00 to 23:59.
- 113 -
Note: If entry delay is active at auto-disarm time, the system does not disarm. A valid disarming procedure is required by the
user who initiated the entry delay.
[003] – Partition Auto-Disarming Holiday Schedules
Use this section to select a holiday schedule group.
See "[711]-[714] Holiday Schedules" on page 132for more information.
[004] – Partition Auto-Arming Pre-Alert Timer
Use this section to program the duration of the auto-arm pre-alert. The system arms when the pre-alert timer expires. Valid
entries are from 001 - 255 minutes.
If a valid access code is keyed in, this timer is postponed for the length of time programmed in Partition Auto-Arm Postpone
timer (see below). The pre-alert timer can be postponed multiple times. Keyswitches and proximity tags can be used to can-
cel auto-arming.
[005] – Partition Auto-Arm Postpone Timer
Use this section to program the length of time the auto-arm pre-alert timer is postponed for. Valid entries are between 001
and 255 minutes. 000 cancels the postpone timer.
When the postpone timer expires, the Auto-arm pre-alert timer restarts (unless the partition is armed). If left uninterrupted the
partition arms at the end of the pre-alert.
If a code is entered during the pre-alert, auto-arm cancel/postpone is logged and communicated and the postpone timer
starts. When the postpone timer expires, pre-alert is sounded again and the cycle repeats. The Auto-arm may be postponed
multiple times.
[006] – Partition No Activity Arming Timer
Use this section to program the duration of the No Activity timer. If this timer expires and no zones have been activated, the
partition arms in Away mode (exit delay will not sound). When the timer expires, keypad buzzers activate for the time pro-
grammed in No Activity Arming Pre-Alert (see below).
The timer restarts when a delay type zone is restored. The timer does not restart when the system is disarmed. The timer
stops if an un-bypassed zone is tripped, tampered or restored or with any keypad activity.
Separate No Activity Arming timers are provided for each partition.
Valid entries are from 000 – 255 minutes. 000 disables this feature.
[007] – Partition No Activity Arming Pre-Alert Timer
Use this section to program the duration of the No Activity Arming pre-alert that sounds when the No-Activity timer for the par-
tition expires. If any key is pressed or zone is activated or restored, the No Activity Arming pre-alert is aborted.
Valid entries are 000 - 255 minutes. 000 disables this feature.
Note : Wireless key arm keys cannot be used to cancel no activity pre-alert.
[200] Partition Mask
A partition is a limited area of the premises which operates independently from the other areas. Partitions are added or
removed from the system by applying or removing a partition mask.
[001] – Partition 1 to 8 Enable Mask
Select options 01-08 to enable or disable partitions.
Partition 1 is always enabled. Partitions 2 to 8 are selectable.
The number of available partitions depends on the model, as shown below:
Model Zones Partitions

HS3032 32 4
HS3128 128 8
HS3248 248 8
- 114 -
[201]-[208] Partition Zone Assignment

Zones can be assigned to any partition. Global zones are zones assigned to more than one partition. A global zone is only
armed when all assigned partitions are armed. The zone is disarmed when any of the assigned partitions is disarmed. By
default, zones 1 through 8 are assigned to partition 1.
To assign zones to partitions, first select a partition [201]-[231], then select a zone group [001]-[016] and then a zone (1-248):
Zone Group Zones Zone Group Zones
001 1-8 017 129-136
002 9-16 018 137-144
003 17-24 019 145-152
004 25-32 020 153-160
005 33-40 021 161-168
006 41-48 022 169-176
007 49-56 023 177-184
008 57-64 024 185-192
009 65-72 025 193-200
010 73-80 026 201-208
011 81-88 027 209-216
012 89-96 028 217-224
013 97-104 029 225-232
014 105-112 030 233-240
015 113-120 031 241-248
016 121-128
All zones assigned to a partition are supervised and operate according to the zone type programmed. If a zone is not
assigned to a partition, it is not supervised and all activity on the zone is ignored by the system.
[300] Panel/Receiver Communication Paths
This section is used to select the path of communications between the alarm system and the central station.
Paths can be established through either the alarm system’s on-board Public Switched Telephone Network (PSTN) con-
nection through the on board Ethernet or through the optional cellular communicator.
Paths to four receivers can be programmed using sections 001 - 004. The communications path for each receiver is defined
by selecting one of the following six options:
[01] Phone Line
Events are communicated through the alarm system phone line programmed in section [301]. If Phone Line is selected for
receiver 1, the phone number programmed in section [301] option [001] is used. If Phone Line is selected for receiver 2, the
phone number programmed in section [301] option [002] is used, etc.
[02] Alternate Communicator Auto Routing
Selecting this option enables the alternate communicator to determine which communications path to use (Ethernet
primary/secondary, and/or cellular primary/secondary). See section [851] Alternate Communicator Programming for details.
[03] Alternate Communicator Receiver 1
Events are communicated through Ethernet receiver 1.
Events are communicated through Ethernet receiver 2.
Events are communicated through cellular receiver 3.
Events are communicated through cellular receiver 4.
- 115 -
[301] Phone Number Programming

Section [301] is used to program up to 4 telephone numbers used to communicate with the central station over PSTN.
[001] The phone number used to communicate with receiver 1
All telephone numbers can be a maximum of 32 digits. Hexadecimal digits may be included to perform the following func-
tions:
l HEX B ([*] [2] [*]) - to dial "*"
l HEX C ([*] [3] [*]) - to dial "#"
l HEX D ([*] [4] [*]) - for an additional dial tone search, as required by PBX telephone systems.
l HEX E ([*] [5] [*]) - to insert a 2-second pause in the telephone number. This causes a static delay of 2 seconds
before any additional dial tone search in a phone number.
l HEX F ([*] [6] [*]) - represents the end of the Phone Number (everything after F is ignored).
l Pressing [#] in these sections exits and saves the entire phone number.
The alarm system does not attempt to communicate using PSTN if no phone number is programmed.
[304] Call Waiting Cancel String
Use this section to program a string that, when pressed, disables call waiting on a phone line. Call waiting cancel is typically
*70 in most areas. Dialing this string before a phone number disables call waiting for the duration of the call.
When this section is programmed and Call Waiting Cancel Options is ON (see "[382] Communicator Option 3" on page 127),
the alarm system dials this string before the phone number. This is only done on the first dialing attempt for each phone num-
ber.
This is a 6-digit field. Fill unused digits with Hex F.
Reporting
[307] Zone Reporting
Zone alarms, tampers and faults are transmitted to the central station using automatic contact ID or SIA formats. Reporting
can be toggled on or off by zone using toggle options 1-6 in subsections 001-248.
See "Reporting Codes" on page 223 for zone reporting code descriptions.
1 - Alarm
2 - Alarm Restore
3 - Tamper
4 - Tamper Restore
5 - Fault
6 - Fault Restore
[308] Event Reporting
System events are transmitted to the central station using automatic contact ID or SIA formats. Reporting can be disabled by
toggle options, programmable in the following sub-sections.
See "Reporting codes" on page 250 for event code descriptions.
[001] Miscellaneous Alarm 1
The reporting codes in this section are sent to the Alarm & Restore call direction group.
1 – Duress Alarm
Sent when a duress code is used to perform any function on the system.
2 – Opening After Alarm
Sent during disarming if an alarm occurred during the previous armed period.
- 116 -
3 – Recent Closing Alarm

Sent if an alarm occurs within 2 minutes of the exit time expiration (for the first alarm only). Zone alarm transmission delays
do not affect this reporting code.
4/5 – Zone Expander Supervisory Alarm/ Restore
Sent when the system loses communication with the following modules:
l Zone Expander Module
l Keypad with an on-board I/O configured as a zone
This reporting code is independent of the general system supervisory code sent to the Alarms and Restores call direction
group.
6 – Burglary Verified
When using Cross Zoning, this reporting code is sent when two crossed zones go into alarm during the cross zone timer.
When using Police Code or sequential detection, this reporting code is sent when any two zones that have the burglary veri-
fication attribute enabled go into alarm. Arming the system resets the zone alarm count for police code or sequential detec-
tion.
7 – Burglary Not Verified
When using Cross Zoning or sequential detection, this reporting code is sent if the cross zone timer is initiated by the first
cross zone alarm, but is not verified by a second alarm before the timer expires.
8 – Alarm Cancel
Sent when a valid access code is entered during the communications cancel window. The central station acknowledges can-
cellation by providing a keypad ringback.
[002] Miscellaneous Alarm 2
1 – Holdup Verified
Sent when the configured Holdup verified conditions have been met.
[011] Priority Alarms 1
The reporting codes in this section are sent to the Alarm & Restore call direction group and apply to all system keypads.
1/2 – Keypad Fire Alarm-[F] Key Alarm/Restore
Sent when [F] Key alarms/restores occur.
3/4 – Keypad Medical Alarm-[M] Key Alarm/Restore
Sent when [M] Key alarms/restores occur. The keypad beeps 10 times when the medical alarm is successfully com-
municated to the alarm monitoring station.
5/6 – Keypad Panic Alarm-[P] Key Alarm/Restore
Sent when [P] Key alarms/restores occur.
7/8 – Auxiliary Input Alarm/ Restore
Sent when an alarm condition occurs/ is restored on PGM 2 (if configured as an input).
[021] Fire Alarms 1
3/4 – PGM 2 2-Wire Alarm/Restore
When PGM 2 is programmed as a 2-wire smoke alarm, this reporting code is sent when an alarm condition is detected and
when it is restored.
[101] Tamper Events
3/4 – Module Tamper/Restore
This reporting code is transmitted when a system module enters a tamper alarm state and uses the System Tamper Alarm
and Tamper Restore call direction.
5 – Keypad Lockout
Sent when a number of invalid access codes have been entered at a system keypad.
This reporting code is sent to the system Tamper Alarm & Tamper Restore call direction group.
- 117 -
7 – Remote Lockout
Sent when a number of invalid access codes have been entered through DLS or Integration. This reporting code is sent to
the system Tamper Alarm & Tamper Restore call direction group.
[201] Open/Close Events 1
1/2 – User Closing/Opening
This reporting code is transmitted when a user arms/disarms a partition and uses the Opening and Closing call direction.
5/6 – Special Closing/Opening
This reporting code is transmitted when a partition is closed/opened using quick arm ([*][0]), downloading, or Stay or Away
function keys without an access code. The Opening and Closing call direction group is used for this reporting code.
7/8 – Keyswitch Opening/Closing
This reporting code is transmitted when a keyswitch zone is used to arm or disarm the system.
[202] Open/Close Events 2
1 – Automatic Closing
This reporting code is transmitted when a partition is automatically armed or schedule armed and uses the Opening call dir-
ection group.
2 – Automatic Disarm
This reporting code is transmitted when a partition is automatically disarmed when a scheduled time of day is reached.
3 – Auto Arm Cancellation/Postpone
This reporting code is transmitted when the automatic arm sequence is canceled during a pre-alert and uses the Opening
and Closing call direction group.
[211] Miscellaneous Open/Close Events
1/2 – Late to Close/Open
This reporting code is transmitted when a partition is not disarmed before the automatic disarm time, when the late to open
option, ([*][6], option 9) is enabled. The Opening and Closing call direction group is used for this reporting code.
5 – Exit Fault
This reporting code is transmitted when an exit error occurs and entry delay expires before the system is disarmed. The
Alarms and Restores call direction group is used for this reporting code.
If the delay zone that caused the exit error has cross zoning enabled, the exit fault and zone alarm transmits if a second zone
is not tripped. The local alarm sequence follows cross zoning rules. The exit error is transmitted with the zone alarm that
caused the fault, even if that zone has transmission delay enabled.
[221] Bypass Events
1/2 – Automatic Zone Bypass/Unbypass
This reporting code is transmitted when a zone is automatically bypassed/unbypassed and uses the Opening and Closing
call direction group.
UK Note: Must be enabled in UK.
03 – Partial Closing
This reporting code is transmitted if zones are manually bypassed at the time of arming or force armed by automatic arming.
The Opening and Closing call direction group is used for this reporting code.
Automatic bypasses caused by stay arming do not cause transmission of this code.
[301] Panel Events 1
1/2 – Panel AC Fail Trouble/Restore
This reporting code is transmitted when the alarm system AC supply fails or has been restored. A programmable delay
applies to both the trouble and the restore. This reporting code is sent to the System Maintenance call direction group.
3/4 – Panel Low Battery Trouble/Restore
These reporting codes are transmitted when the panel battery voltage falls below 11.5VD or is restored. These reporting
codes are sent to the System Maintenance call direction group.
5/6 – Panel Battery Absent Trouble/Restore
These reporting codes are transmitted when the panel battery is not connected or is restored. These reporting codes are
sent to the System Maintenance call direction group and are transmitted when the panel battery is detected as absent.
- 118 -
7/8 – Panel Power Unit Failure/Restore

These reporting codes are transmitted when the power unit fails or is restored.
1/2 – Bell Circuit Trouble/Restore
This reporting code is transmitted when a bell trouble condition occurs or is restored on the system. This reporting code is
sent to the System Maintenance call direction group.
3/4 – Telephone Line Trouble and Restore
This reporting code is transmitted when an alarm controller TLM trouble occurs or is restored. The TLM trouble is com-
municated over an unaffected communication path if available.
This reporting code is sent to the System Maintenance call direction group.
5/6 – Auxiliary Power Supply Trouble/Restore
This reporting code is transmitted when an auxiliary voltage supply trouble occurs or is restored. This reporting code is sent
to the System Maintenance call direction group.
7/8 – Overcurrent Trouble/Restore
This reporting code is transmitted when an overcurrent trouble occurs or is restored. Current threshold is 2 amps.
3/4 – PGM 2 2-Wire Trouble/Restore
This reporting code is transmitted when a trouble condition on PGM 2, configured as two-wire smoke, occurs or is restored.
This reporting code is sent to the System Maintenance call direction group.
[311] Maintenance Events 1
1/2 – RF Jam Trouble/Restore
Sent when RF jam troubles occur/are restored. The following events cause RF jam troubles:
l Wireless repeater jamming
l RF jam
3/4 – Fire Trouble/Restore
Sent when a low sensitivity, tamper or internal fault condition/restore is detected on a wireless smoke detector or supervisory
fault with a hardwired smoke detector.
5 – Cold Start
Sent when power is restored to the alarm system after total power failure. The code is sent after 2 minutes to allow the alarm
controller to stabilize.
6 – Delinquency
When the Delinquency option is off (page 119), this code is transmitted if the alarm system has not been armed for the num-
ber of days programmed in the Delinquency Transmission Delay (page 124).
When the Delinquency option is on, this code is transmitted when no zone activity has been detected on the system for the
number of hours programmed in Delinquency Transmission Delay.
7 – Self Test Trouble
Sent when a self test trouble occurs for an outdoor PIR.
8 – Self Test Trouble Restore
Sent when a self test trouble has been restored for an outdoor PIR.
1/2 – Installer Lead In/ Lead Out
The Installer Lead In and Lead Out reporting codes are sent when the alarm system enters and exits Installer Programming
respectively.
3/4 – DLS Lead In/Lead Out
The DLS Lead In reporting code is sent:
l after DLS communication has been successfully established, but before the alarm system calls back the down-
loading computer. This code is only transmitted when call back is enabled.
l on user-initiated call-up.
The DLS Lead Out reporting code is sent when a DLS session is successfully ended.
- 119 -
Note: If DLS is terminated by an alarm, the DLS Lead Out reporting code is not transmitted.
5/6 – SA Lead In/Lead Out
The SA Lead In reporting code is sent:
l after SA communication has been successfully established, but before the alarm system calls back the downloading
computer. This code is only transmitted when call back is enabled.
l on user-initiated call-up.
The SA Lead Out reporting code is sent when an SA session is successfully ended. The SA Lead Out reporting code is still
sent if the session is terminated by an alarm.
7 – Event Buffer 75% Full
Sent when the event buffer reaches a threshold of 75% without being uploaded.
1/2 – Firmware Update Begin/was Successful
Sent when a remote firmware update is initiated/ is successfully completed.
3 – Firmware Update Fail
Sent after an unsuccessful remote firmware update.
1/2 – Gas Trouble/Restore
Sent when a trouble occurs or is restored on a wireless gas detector.
3/4 – Heat Trouble/Restore
Sent when a heat trouble occurs or is restored on a wireless temperature detector.
5/6 – Freeze Trouble/Restore
Sent when a freeze trouble occurs or is restored on a wireless temperature detector.
7/8 – Probe Disconnected Trouble/Restore
Sent when a probe disconnected trouble occurs or is restored on a wireless temperature detector.
[321] Receiver Events
2/4/6/8 – Receiver 1 - 4 FTC Restore
Sent when the panel detects an FTC trouble.
[331] Module Events 1
1/2 – Module AC Trouble/Restore
This reporting code is transmitted when a module’s AC supply fails or has been restored. A programmable delay applies to
both the trouble and the restore. This reporting code is sent to the System Maintenance call direction group.
3/4 – Module Battery Trouble/Restore
These reporting codes are transmitted when a module’s battery voltage falls below 11.5VDC or is restored. These reporting
codes are sent to the System Maintenance call direction group.
5/6 – Module Battery Absent/Restore
These reporting codes are transmitted when a module’s battery is absent or is restored. These reporting codes are sent to
the System Maintenance call direction group.
7/8 – Module Power Unit Failure/Restore
These reporting codes are transmitted when a module’s battery is detected as absent or restored. These reporting codes are
sent to the System Maintenance call direction group.
1/2 – Module Low Voltage Trouble/Restore
Sent when module voltage drops below acceptable levels or is restored.
3/4 – Module Supervisory Trouble/Restore
Sent when communication with a module is lost or restored.
5/6 – Module Aux Trouble/Restore
Sent when a high current output module or power supply module experiences an auxiliary voltage supply trouble.
- 120 -

1/2 – Output 1 Fault/Restore
This reporting code is sent when the first output on the high-current output expander module goes into fault (open or short)
or is restored.
Only the first output on the high-current expander module is supervised.
[351] Alternate Communicator 1
1/2 – Alt. Comm Communications Fault/Restore
Sent when the system loses or restores communications with the alternate communicator.
3/4 – Reserved
5/6 – Reserved
7/8 – Alt. Comm Radio/SIM Failure/Restore
Sent when the alternate communicator experiences trouble or restore of the radio/SIM.
1/2 – Alt. Comm Network Fault/Restore
Sent when the alternate communicator loses or restores communication with the network.
5/6 – Alt. Comm Ethernet Trouble /Restore
Sent when the alternate communicator detects a network absent condition or DHCP failure or restore.
Receiver 1 to 4 Trouble and Restore
Sent when the alternate communicator detects a trouble or restore condition on receiver 1-4.
1/2 – Receiver 1 Trouble/Restore
Receiver 1 to 4 Supervision Failure and Restore
Sent when the alternate communicator detects a supervision trouble for the Ethernet receiver (1, 2) or the GPRS receiver (3,
4).
1/2 – Receiver 1 Supervision Failure/Restore
[361] Wireless Device Events
1/2 – Wireless Device AC Failure/Restore
These options are used to enable wireless device AC failure/restore reporting codes. These reporting codes are sent when
a wireless device experiences an AC failure/restore.
3/4 – Wireless Device Low Battery Trouble/Restore
These options are used to enable wireless device low battery trouble/restore reporting codes. These codes are sent when a
wireless device experiences a low battery trouble/restore.
5/6 – Wireless Device Fault/Restore
These options are used to enable wireless device fault/restore reporting codes. This reporting code is sent when a wireless
device experiences a supervisory fault.
[401] System Test Events
1/2 – Walk Test Start/End
Sent when installer walk test is initiated and terminated.
These reporting codes are in addition to the alarm reporting codes for the zones that are tripped during the walk test period.
- 121 -
3 – Periodic Test Transmission

Sent when the test transmission programmed in section "[401] System Test Events" on page 121 occurs.
4 – Periodic Test Transmission with Trouble
Sent when any of the following trouble conditions are present during a periodic test transmission:
l Fire Zone Trouble
l Battery Trouble
l Fire Zone Alarm (2-Wire Smoke)
l Aux Trouble
l Fire Trouble
l Bell Trouble
l Fire Tamper/Low Sensitivity (Wireless)
l Module Supervisory
l Fire Zones Bypassed
l Ground Fault
l Fire Supervisory (Wireless)
l TLM Trouble
l AC Trouble
l FTC Trouble
This reporting code is sent in place of the standard Periodic Test Transmission code.
5 – System Test
Sent when a manual system test is performed ([*][6][Master Code][04]).
System Communications
The programming options in this section are used to configure communications between the alarm system and the central
station.
[309] System Call Direction
Use this programming option to select the central station receivers that system events are communicated to. A system event
can be sent to multiple receivers.
[001] Maintenance Events/Restores (all troubles except tampers)
These options control which receiver paths are enabled for maintenance events. To assign a maintenance event to a
receiver, select from the following list:
[01] Receiver 1
[02] Receiver 2
[03] Receiver 3
[04] Receiver 4
[002] Test Transmissions
These options control which receiver paths are enabled for test transmission events. To assign a test transmission event to a
receiver, select from the following list:
[01] Receiver 1
[02] Receiver 2
[03] Receiver 3
[04] Receiver 4
[310] Account Codes
These programming sections are used to set the system and partition account codes.
[000] System Account Code
The system account code is used to identify the alarm system when communicating system events to the central station. The
system account code can be either 4 or 6 digits long. 4 or 6 digit account codes are selected with [383] option 2. Program a
6-digit code only when using the SIA reporting format. SIA uses this account code for all partitions and system events. All
other reporting formats use a 4-digit system account code to report system maintenance (e.g., low battery, zone fault) and
test transmission events. To program a 4-digit code, add FF to the last two digits.
- 122 -
[001]-[008] Partition Account Codes

Use these sections to program account codes for each partition.
When using formats other than SIA, these account codes identify the alarm system to the central station when com-
municating partition-specific events.
Note: The system will not communicate if the account code is not programmed. When this condition occurs, Account Code
Not Programmed is briefly displayed on the keypad when exiting Installer Programming mode.
Note: If no phone numbers are programmed, the error message does not occur.
[311]-[318] Partition Call Directions
Use this programming option to select the central station receivers that partition events are communicated to. Call directions
can be programmed for each partition. Each event can be sent to one of four receivers.
[001] Alarm/ Restore
These options control which receiver paths are enabled for Partition 1-8 Alarm and Restore event reporting codes.
To assign an event to a receiver, select one of the following options:
[01] Receiver 1
[02] Receiver 2
[03] Receiver 3
[04] Receiver 4
[002] Tampers (Including System Tampers)/ Restore
These options control which receiver paths are enabled for Partition 1-8 Tamper and Restore event reporting codes.
To assign an event to a receiver, select one of the following options:
[01] Receiver 1
[02] Receiver 2
[03] Receiver 3
[04] Receiver 4
[003] Openings/ Closing
These options control which receiver paths are enabled for Partition 1-8 Opening and Closing event reporting codes. To
assign an event to a receiver, select one of the following options:
[01] Receiver 1
[02] Receiver 2
[03] Receiver 3
[04] Receiver 4
[350] Communicator Formats
Use this programming option to assign a communicator format to each of the four receivers programmed in section [301].
The available communicator formats are as follows:
03 DTMF Contact ID
04 SIA FSK
To assign a communications format, select a receiver (option [001]-[004]) then enter the 2-digit code corresponding to the
chosen format. For detailed descriptions of each format, see "Reporting codes" on page 250.
[377] Communication Variables
[001] – Swinger Shutdown
Alarms/Restores
This value defines the number of communication attempts made for alarm/restore events, per zone, before the zone goes
into swinger shutdown. Valid entries are 000 to 014. For CP-01, entries are from 001-006.
Once the programmed number of alarm/restore events have been communicated, no further alarm/restore events for the
zone are communicated until swinger shutdown is reset. The last restore event is not communicated until swinger is cleared.
- 123 -
For example, if the swinger shutdown limit for zone alarms is set to [003], the cycle is as follows: alarm/restore, alarm/restore,
alarm...8 hours or arm/disarm...restore.
The bell output is not activated for alarms on zones that have exceeded the swinger shutdown counter limit. Swinger shut-
down on global zones log once to the system area.
CP-01 Note: Swinger shutdown resets on all partitions when any partition on the system is armed or disarmed, or every day at mid-
night. For CP-01, swinger shutdown is restored after 8 hours of inactivity.
Once reset, the alarm system communicates normally.
Note: The event buffer can follow swinger shutdown if enabled.
Tampers/Restores
This value defines the number of times the same system tamper event occurs before going into swinger shutdown. Valid
entries are 000 to 014.
Maintenance Troubles/Restores
This value defines the number of times the same system Maintenance (trouble) type event occurs before going into swinger
shutdown. Fire troubles follow the Maintenance Swinger Shutdown variable.
[002] – Communication Delays
Transmission Delay (seconds)
This value defines the delay before an alarm is transmitted.
The delay is for zones which have the Transmission Delay attribute enabled. Valid entries are from 000 to 255 seconds (0-
45 seconds for CP-01). Each partition shares the same active timer. If the delay is already active due to an alarm on a dif-
ferent partition, any new activity on another partition does not restart the communications delay timer.
Burglary verified events are postponed until after the transmission delay expires. When a valid disarming procedure is used
while the transmission delay is active, a communications canceled message is briefly displayed on the keypad when the
delay is canceled.
NA Note: For UL/ULC listed installations, the entry delay plus communication delay cannot exceed 45 seconds.
AC Failure Communication Delay (minutes or hours)
This value determines the delay before an AC failure or AC restore is reported. The AC failure or restore is still displayed
immediately. Valid entries are from 000 to 255 minutes/hours (max. 180 minutes for UL commercial installations). Selection
of minutes or hours for the delay is set in section "[382] Communicator Option 3" on page 127.
Note: If AC Failure Communications Delay is programmed as 000, the AC Failure Trouble reporting code is sent imme-
diately.
ULC Note: For ULC commercial fire monitoring, the setting shall be 180 minutes.
TLM Trouble Delay
Use this section to program the number of valid checks (3 second intervals) required before a telephone line trouble is gen-
erated. Valid entries are 000-255 for trouble annunciation and transmission delays of 3 to 765 Seconds (12.75 Minutes).
Wireless Zone Low Battery Transmission Delay (in days)
When a zone reports a low battery condition, the trouble is indicated immediately on the keypad, but the transmission to the
monitoring station is delayed by the number of days programmed in this section. If the low battery condition is not corrected
before the delay expires, the low battery condition is transmitted. The Low Battery Restore transmission is not delayed.
Delinquency Transmission Delay
The value in this section determines the period of time before a delinquency event is generated.
Delinquency delay is measured in days if using closing delinquency or hours if using activity delinquency as programmed in
section [311] option 6. Valid entries are [001]-[255] or [000] to disable.
Communications Cancel Window
After the transmission Delay expires and a zone alarm is transmitted, the communications cancel window begins.
If an access code is entered during this window, a reporting code is communicated and logged. If the window expires
without an access code entry or a code is entered after the window, the communications canceled event is not logged or
communicated.
Note: The cancel window does not start after an [F][M][P] key alarm.
- 124 -
[003] – Periodic Test Transmission Cycle

This value determines the period between test transmissions. Valid entries are [000]-[255]. Whether this interval is in hours
or days is determined by section [022], option 4.
NA Note: For UL/ULC installations, the test interval depends on the type of application. For setting the correct values, refer to
Regulatory approvals.
[004] – Periodic Test Transmission Time of Day
Enter a 4-digit time using the 24-hour clock format (HH:MM).
Valid entries are from 00 to 23 for the hours (HH) and 00 to 59 for the minutes (MM).
To disable the test transmission time of day, enter [9999] in this section.
Note: This time should not be set for the same time as Day Light Savings time.
[011] – Maximum Dialing Attempts
This section is used to program the number of dialing attempts made to each telephone number when communicating. Valid
entries are 001-005.
NA Note: For UL/ULC listed installations, this value must be set to 005.
[012] – Delay Between PSTN Attempts
This programmable timer adds a delay before the next call is attempted over PSTN. Valid entries are 000-255, with a default
of 3 seconds (making a total of 8 seconds: 3-second delay + standard 5-second dial tone search).
[013] – Delay Between Force Attempts
This programming option is used to set the length of time the alarm system waits between the first dialing attempt and the
force dial attempt.
Valid Entries are 001-255 seconds. Default is 020.
[014] – Post Dial Wait for Handshake
This option is used to program the length of time the communicator waits for a valid initial handshake from the receiver after
dialing the programmed telephone number. Valid entries are 001 to 255 seconds.
UL Note: Maximum 45 seconds for UL installations.
[015] – IP Wait for Ack
This option is used to program the length of time the communicator waits for an acknowledge after transmitting via IP/GS.
Valid entries are 001 to 255. Default is 60 seconds.
[016] –IP/Cellular Fault Check Timer
This section is used to program the number of poll commands sent without valid poll responses before the alarm system gen-
erates a trouble condition. The checks occur at 3-second intervals.
Valid entries are 003-255 for trouble annunciation and transmission.
The trouble restore is not delayed.
[380] Communicator Option 1
1 – Communications Enabled/Disabled
ON: (Default) The system communicator is enabled and all events with reporting codes are reported to the monitoring sta-
tion. Refer to the Telephone Number, Reporting Code and Call Direction programming sections.
OFF: The system communicator is disabled and no events are reported to the monitoring station.
Note: Disabling the communicator clears all FTC troubles.
2 – Restore On Bell Timeout
ON: Zone restore reporting codes are not transmitted until the zone has been restored and the bell timeout has expired. If the
zone is not restored when the bell cut-off time expires, the restore is transmitted when the zone physically restores or when
the system is disarmed.
Note: 24-hour zones will not restore until the zone is physically restored
OFF: Zone restore reporting codes are transmitted when the zone is physically restored. If zones are still active when the sys-
tem is disarmed, the restore codes are transmitted when the system is disarmed.
- 125 -
3 – Pulse Dialing
ON: The alarm system dials telephone numbers using pulse (rotary) dialing.
OFF: The alarm system dials telephone numbers using DTMF (dual tone multi-frequency) touch-tone dialing.
4 – Pulse Dial after 5th Attempt
ON: If DTMF dialing is enabled, the alarm system dials telephone numbers using DTMF dialing for the first 4 attempts. If
unsuccessful, the alarm system switches to pulse (rotary) dialing for the remaining attempts.
OFF: If DTMF dialing is enabled, the alarm system dials telephone numbers using DTMF dialing for all dialing attempts.
5 – Parallel Communications
ON: Parallel communications is enabled. The alarm system attempts to communicate through all available receiver paths
(PSTN and IP (IP=Ethernet or Cellular) at the same time. Once acknowledgment is provided by any of the receivers, the
alarm system communicates the next event. If more than one receiver is configured for PSTN, the backup procedure
described below is followed.
OFF: Parallel communications is disabled. If receiver 1 fails, the alarm system attempts to communicate with the next avail-
able receiver (2-4) in sequence.
Note: When Parallel Communications is enabled it will override Communicator Backup Options, see "[384] Communicator
Backup Options" on page 128 for communicator backup programming.
6 – Alternate Dial
ON: After each failed dialing attempt, the communicator switches to the next backup receiver in the sequence:
l Receiver 2 backs up Receiver 1
This continues until communication is successful or the sequence has been repeated 5 times (depending on the number of
maximum dialing attempts). If all 5 attempts fail, an FTC trouble for the primary phone number is logged. All backup receivers
automatically use the same call directions and format as the primary receiver.
OFF: After 5 failed attempts to communicate with the primary receiver, the communicator switches to the next backup
receiver in the sequence and makes up to 5 more attempts. This continues until communication is successful or until all
backup receivers fail, at which point an FTC trouble for the primary number is logged.
7 – Reduced Dialing Attempts
ON: If a TLM trouble is present, The alarm system immediately attempts to call the backup receiver. This option only applies
to PSTN. Backup communications must be enabled. See option 5, Parallel Communications.
A minimum of two receivers should be enabled for this feature to operate as intended. This feature should not be enabled
unless the panel is programmed to use backup communication paths.
OFF: If a TLM trouble is present, the number of dialing attempts programmed shall be attempted before moving on to the
backup receiver.
8 – Activity Delinquency
ON: Inactivity on a partition for a programmed duration (section [377] option 002, Delinquency Transmission Delay) transmits
a Delinquency code to the central station. This option is designed to help monitor the elderly or disabled. The counter is
reset if zone activity is detected or if the system is armed. The Delinquency Transmission Delay is in hours.
Note: Delinquency code is not transmitted while Away armed. Activity on bypassed zones does not affect this timer.
OFF: The Delinquency reporting code is sent when the programmed number of days for delinquency (section [377]) expires
without the partition being Armed. Once the code is sent, the timer is not started again until the partition has been armed.
Each day programmed in the counter represents one day plus the time it takes for the partition to reach midnight. To disable
this feature, program 000 in section [377]>[002] option 5.
1 – Keypad Ringback
ON: When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the
keypad emits a series of 8 beeps to confirm to the occupant that the code was sent and received. Ringback occurs for each
successfully reported Opening After Alarm code.
OFF: When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the
keypad does not sound ringback.
- 126 -
2 – Bell Ringback
ON: When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the siren
emits a series of 6 squawks to confirm to the occupant that the code was sent and received. Ringback occurs for each suc-
cessfully reported Opening After Alarm code.
OFF: When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the siren
does not sound ringback.
4 – Closing Confirmation Enabled/Disabled
ON: When a Closing reporting code is successfully transmitted to a programmed telephone number, the keypad emits a
series of 8 beeps to confirm to the occupant that the Closing Code was sent and received.
OFF: No keypad ringback is generated when a Closing reporting code is successfully transmitted.
8 – Communications Priority Enabled/Disabled
ON: Events follow the priority level indicated in ULC-S559 standard.
Concurrent event communications are prioritized in the following order (highest to lowest priority):
1. Fire Alarms
2. CO Alarm
3. Fire Supervisories
4. Fire Trouble
5. Monitoring (Medical, Panic or Security)
6. All others such as restorals for fire alarms, supervisories, troubles and monitoring.
OFF: Events are communicated in the order they occur.
ULC Note: Must be ON for ULC commercial fire monitoring listed installations.
1 – Reserved
2 – Walk Test Communications
ON: Zone alarms that occur during Walk Test are communicated if programmed to do so.
OFF: Zone alarms during Walk Test are not communicated. FMP key alarms are still communicated.
4 – Call Waiting Cancel
ON: The call waiting cancel string (See "[304] Call Waiting Cancel String" on page 116) is used on the first attempt to dial
each phone number. It is not used on any further dialing attempts.
OFF: The call waiting cancel string is not dialed.
5 – Interactive Communicator Enable/Disable
ON: The system communicates using the Alarm.com communicator. All related programming options, reporting, and super-
vision are enabled when programmed via PC-Link2.
OFF: The Alarm.com communicator and all associated programming functionality are disabled.
6 – AC Failure Communication Delay in Hours/Minutes
ON: The AC failure communication delay (section [377]>[002] option 2) is programmed in hours.
OFF: The AC failure communication delay is programmed in minutes.
8 – Tamper Limit
ON: When disarmed, the system only communicates module tampers. Zone tampers are not communicated.
OFF: When disarmed, the system communicates all tampers.
1 – Phone Number Account Code
ON: The account code communicated to the central station follows the phone number the event is programmed to com-
municate on (programmed in section "[310] Account Codes" on page 122):
l Receiver 1 all events will follow partition 1 account code
- 127 -

OFF: Events follow the account code assigned to each partition when communicating.
Note: This feature only works with CID
2 – 4 or 6-Digit System Account Code
ON: The programmable account code in section [310][000] is 6 digits long (used for SIA format).
OFF: The programmable account code in section [310][000] is 4 digits long.
3 – Ethernet Enable
ON: Enables the on-board ethernet.
OFF: Disables the on-board ethernet.
4 – Cellular Enable
ON: Enables the plug-in communicator module.
OFF: Disables the plug-in communicator module.
5 – Communicate FTC Events
ON: The alarm system communicates FTC (failure to communicate) events. The FTC Trouble/Restore reporting code trans-
mission follows the call direction the events are assigned to.
OFF: FTC events are not communicated. FTC Trouble/Restore reporting codes are communicated to the Maintenance call
direction group after the next successful communication.
[384] Communicator Backup Options
2 – Receiver 2 Backup Option
ON: Receiver 2 backs up Receiver 1. Receiver 2 is only used if an FTC event is detected on Receiver 1.
Receiver 2 uses the same format programmed for Receiver 1.
OFF: Receiver 2 is independent and will communicate if a number and format are programmed.
[385] Audio Module Talk\Listen Mask
1- Talk/Listen on Receiver 1
ON: 2-way audio sessions can be initiated over receiver 1.
OFF: Regardless of other 2-way audio programming, 2-way audio sessions cannot be initiated over receiver 1.
2- Talk/Listen on Receiver 2
3-Talk/Listen on Receiver 3
4-Talk/Listen on Receiver 4
- 128 -
DLS Programming
Downloading allows programming of the entire alarm system via a computer. All functions and features, changes and status,
such as trouble conditions and open zones, can be viewed or programmed by downloading.
The following downloading options are available:
l 6-hour window on start up: When the alarm system is powered up, downloading access is available for 6 hours. This
provides the option of downloading without having to complete any keypad programming.
l Double call method: The installer initiates a downloading window by calling the alarm system, hanging up, then call-
ing back again.
l User enabled DLS window: The user initiates a downloading window using [*][6][Master code][05]. This can be a 6-
hour window where the installer initiates and terminates downloading as many times as necessary, or it can be a 1-
hour, 1 use window.
l User initiated call-up: the user can initiate a downloading session using [*][6][Master Code][06].
l On-site downloading using USB: The installer connects a computer directly to the alarm system to perform on-site
downloading.
l Auto event buffer upload: The Event buffer is automatically uploaded to the DLS/SA computer when it reaches 75%
full.
Refer to the DLS/SA programming sections described below for configuration options.
[401] DLS/SA Options
1 – Double Call
ON: Calls for downloading or SA are answered if a successful double call routine is detected. Have the downloading com-
puter call the system and let the telephone line ring once or twice. After 1 or 2 rings, hang up. If called back within the dur-
ation of the double call timer (section [405]), the alarm system answers on the first ring.
OFF : Incoming calls are not answered using the double call routine unless the user enables the DLS window.
Note: This feature controls the DLS window for PSTN connections only.
2 – User Enables/Disables DLS
ON : The [*][6][Master Code][05] command enables a 6-hour window where, on power-up, downloading calls are answered
if a successful double call routine is detected.
OFF: The user cannot enable a downloading window.
3 – DLS CallBack
ON : When a downloading call is answered, both the computer and the alarm system hang up. The alarm system then calls
the downloading computer back using the [402] downloading telephone number and begins the DLS session.
Note: Disable this option if using more than one downloading computer.
OFF : After successful validation, the downloading computer gains immediate access to the alarm system.
4 – User Call-Up
ON : A single call attempt can be made to the downloading computer using [*][6][Master Code][06].
OFF: [*][6][Master Code][06] does not allow initiation of a downloading session.
6 – Panel Call-Up and Baud Rate
ON : When a DLS/SA session is initiated by the user, the initial header is sent at 300 baud.
OFF: When a DLS/SA session is initiated by the user, the initial header is sent at 110 baud. The alarm system will then
switch to 300 baud in order to receive the response from the DLS computer.
7 – Alternate Communicator DLS
ON: When this feature is enabled, the alarm system responds to DLS requests through the alternate communicator IP or cel-
lular paths at any time, regardless of whether the DLS window is active or not.
However, if a pre-defined number of consecutive incorrect DLS access codes is detected (See "Remote Lockout DLS" on
page 101) while trying to establish a connection, alternate communicator DLS access is locked out until the next hour roll-
over.
OFF: When this feature is disabled, the alarm system only responds to DLS requests through the alternate communicator IP
or cellular paths when the DLS window is active.
The DLS/SA window is active following a power up or if enabled using [*][6][maser code][05] (System Service/DLS).
- 129 -
Note: This option controls DLS over alternate communicator only.

[402] PSTN DLS Phone Number Programming
This section is used to program the telephone number for DLS downloading over PSTN. This phone number is used for User
Call Up, Periodic DLS and DLS Call back. If no phone number is programmed, the system attempts to use the alternate com-
municator IP path (if configured).
The maximum number length is 32 digits.
[403] DLS Access Code
This 6-digit hexadecimal code allows the alarm system to confirm the identity of the downloading computer.
If the code does not match the computer, the alarm system does not allow DLS access.
Once a DLS connection is established, the operator is allowed three attempts to enter the correct access code. If these
attempts are unsuccessful, the alarm system disconnects and a new attempt must be made.
If cellular or IP paths are used for the DLS connection, a pre-programmed number of unsuccessful attempts causes a 1-hour
DLS lockout. Number of attempts is programmed in section [012].
[404] DLS/SA Panel ID
This 12-digit hexadecimal code identifies the alarm system to the downloading computer.
[405] PSTN Double Call Timer
Use this section to program the amount of time that can elapse between the first and second call when using Double Call
downloading. Valid entries are 001 to 255 (seconds).
[406] PSTN Number of Rings to Answer On
The value in this section determines how many rings are required in order to establish a DLS connection. When set to 000
(default) this feature is disabled.. Valid entries are [000]-[020].
Note: If Double-Call option and Number of Rings to Answer are enabled, either one will work depending on how the
installer calls the alarm system.
[407] SA Access Code
This 6-digit hexadecimal code allows the alarm system to confirm the identity of the downloading computer.
If the code does not match the computer, the alarm system does not allow uploading/downloading.
Programming the access code as FFFFFF disables SA access.
Once an SA connection is established, multiple attempts to input the correct downloading access code (programmed in
[012]) is allowed.
The operator is allowed three attempts to enter the correct access code. If these attempts are unsuccessful, the alarm system
disconnects and a new attempt must be made.
If cellular or IP paths are used for the SA connection, up to five unsuccessful attempts causes a 1-hour SA lockout (See
"Remote Lockout DLS" on page 101).
[410] Automatic DLS/SA Options
[001] – Auto DLS Options
1 – Periodic DLS
ON: Upload/download commands programmed in advance (batch files) are periodically downloaded to the DLS computer.
See below to program the times and days when this occurs.
Note: The computer must be waiting for a call in order for this feature to work.
OFF: The alarm system does not periodically call the downloading computer.
3 – DLS on Event Buffer %75 Full
ON: The alarm system automatically calls the downloading computer with DLS when the Event Buffer 75% full event occurs.
This option is independent of the actual transmission of the Event Buffer 75% full event (the event does not need to be trans-
mitted for the panel to perform the automatic upload).
- 130 -
The panel first communicates the Event Buffer 75% full event (if enabled) using either PSTN or IP and then performs the auto-
matic download.
OFF: The alarm system does not automatically call the downloading computer when the Event Buffer 75% full event occurs.
8 – DLS on Programming Change
ON: When the panel returns to the "Ready to Arm" screen after a programming change, 15 minutes later the alarm system
automatically connects to the downloading computer.
OFF: The alarm system does not automatically call the downloading computer when the system programming changes.
[002] Periodic DLS Days
This section is used to program the number of days between periodic DLS downloads. Valid entries are from 001 to 255
days.
[003] Periodic DLS Time
This section is used to program the time of day periodic DLS download takes place. Time is in 24-hour format and the default
is 00:00 (midnight).
[007] Delay Call Window
The delay call window is the upper and lower limits of a random time the panel may initiate a call up to a remote computer.
This feature shall be applied to Periodic DLS Days. When a value is entered in this section, the setting in Periodic DLS Time
(see the option above) is overridden. When 00:00 is entered in this field, the alarm system initiates a DLS call at the time pro-
grammed in Periodic DLS Time. Start and end times must be defined using 24-hour format (e.g., 13:30) and cannot span a
day (e.g., start time of 23:00 and an end time of 01:00).
Virtual Inputs
When using a third party integration, virtual zones can be mapped to configured system zones.
[560][001]-[032]
Assign corresponding 3 digit zone number to virtual input and then the virtual input can be controlled by a third party integ-
ration.
Schedule Programming
The sections described below are used for programming scheduled operating times for PGM command outputs 1-4.
[601]-[604] Programming Schedule 1-4
These sections are used to define schedules for PGM command outputs 1-4 operation. When a PGM is configured for timed
output operation, it activates at the programmed start time and will turn off after the programmed duration. For example, 5
seconds.
Each schedule contains 4 intervals, for Command Outputs 1-4. Within each interval, a start time and end time can be pro-
grammed for each day of the week. Holiday schedules 1-4 can also be selected. To enable the command output to follow a
schedule, program the command output in section [009] and then enter schedule 001 - 004 in section [011].
[101]-[102] Set Start Time/ End Time
Used to program the time of day the schedule interval begins and ends. (HH:MM). Valid entries are 0000-2359 and 9999.
The end time must be equal to or greater than the start time. 9999 is used when an interval needs to extend past 24 hours.
To do this, program the start time of the first interval then the end time with 9999. Program the start time of the second interval
as 9999 and the end time with the desired time when the output should deactivate. Select the day of the week the schedule
will end.
Note: If two intervals in a schedule are programmed with the same start time, the schedule follows the interval with the
longest end time.
[103] Days Assignment
Used to program the day of the week that the schedule interval starts and ends. Use the scroll keys to select a day then
toggle the option on. Multiple days of the week can be enabled.
[104] Holiday Assignment
Program PGMs to follow holiday schedule group 1-4. Select (Y) to enable. If all days of the week for an interval are disabled
(N), the schedule activates on the enabled holidays.
- 131 -
[711]-[714] Holiday Schedules

Use this section to program holiday schedules. During holiday schedules, other scheduled events do not occur. Enter sec-
tion 711 to 714 for holiday group 1 to 4.
Each of the four available holiday groups can have up to 99 holiday schedules programmed.
[001]-[099] Holiday Dates 1-99
Program holiday dates in the following format: MMDDYY
MM valid entries are 01 to 12
DD valid entries are 01 to 31
YY valid entries are 00 to 99
[802] Audio Verification Module Programming

This module provides 2-way audio communication between the central station and the occupants of the premises.
Note: For complete programming descriptions and worksheets, see the HSM2955 Audio Verification module installation
manual.
Wireless Programming
[804] Wireless Programming
This programming section is used to enroll, program and delete wireless devices. Note that the HSM2HOSTx wireless trans-
ceiver or RF model keypad must be installed in order to enroll wireless devices.
Note: Refer to the HSM2HOST installation manual for information.
Communicator Programming
[850] Cellular Signal Strength
This section is used to view both the cellular signal strength and the radio technology in use.
Table 5-4 : Cellular Technology
Display Technology
GP GPRS
ED EDGE
HS HSPA
H+ HSPA
CD CDMA
EV EVDO
LT LTE
5 bars indicate maximum signal strength. 0 bars indicate the communicator is not connected to the network.
[851] Alternate Communicator Programming
The programming sections described in this document can be viewed at the keypad. To start programming, enter: [*] [8]
[installer code] [851] [section number], where section number is the 3-digit section number referenced in this section. The pro-
gramming worksheets at the end of this document can be used to record the new values when programming changes have
been made from the default values. Installers may review/record programming options at the panel keypad.
System Options
[001] Ethernet IP Address
Default (000.000.000.000)
Enter the IP address of the communicator. Ensure that the IP address is unique to the communicator on the local network.
- 132 -
Format is 4 fields, each field is a 3 digit decimal number. Valid range: 000-255. If an IP address is programmed in this sec-
tion, the unit will operate with static IP (DHCP disabled). Sections [002] and [003] must also be programmed when using
static IP addresses.
Note: Default for this section is Dynamic Host Configuration Protocol (DHCP) enabled. When enabled, the DHCP server will
set values for: IP address [001], subnet mask [002], and gateway [003]. Programming an IP address in this section will dis-
able DHCP (Static IP).
[002] Ethernet IP Subnet Mask
Default (255.255.255.000)
Enter the Ethernet IP subnet mask of the communicator. Format is 4 fields, each field is 3 digits. Valid range: 000-255.
Note: If DHCP is enabled, the DHCP server will assign the subnet mask for this section and the programmed value will be
ignored.
[003] Ethernet Gateway IP Address
Default (000.000.000.000)
Enter the Ethernet gateway IP address of the communicator. The gateway IP address is required when a router is used on
the local network to reach the destination IP address specified in section [001]. Format is 4 fields, each field is a 3-digit
decimal number.
Valid range: 000-255.
Note: If DHCP is enabled, the DHCP server will assign the gateway IP address for this section and the programmed value
will be ignored.
[004] Receiver Supervision Interval
Default (135)
When receiver supervision is enabled (ON) in section [005] toggle option [3], the unit sends heartbeats to Ethernet receiver 1
or cellular receiver 1 to test the communications path. Use this section to set the interval time (in seconds) when heartbeats
will be sent to the receivers. Valid range 00000-65535 seconds. If the programmed value is less than 10 seconds, super-
vision is disabled.
[005] System Toggle Options
[1] Ethernet Receiver 1 Supervised Default (OFF)
ON: Ethernet receiver 1 will be supervised and heartbeats will be sent to Ethernet receiver 1 based on the super-
vision interval programmed in section [004].
OFF: Ethernet receiver 1 will not be supervised. When disabled, heartbeat 1 is sent to the Ethernet receiver once
every hour, regardless of supervision type (heartbeat 1 or 2). The heartbeat is resent every 5 seconds until ACK is
received. If no event or heartbeat ACK is received after (receiver supervision interval + 75 seconds), supervisory
trouble is indicated.
Note: Ethernet receiver 2 can not be supervised.
[2] Cellular Receiver 3 Supervised Default (OFF)
ON: Cellular receiver 3 will be supervised and heartbeats will be sent to cellular receiver 1 based on the supervision
interval programmed in section [004]. If ACK to heartbeat is not received, it is retransmitted every 5 seconds. Failure
to ACK two consecutive heartbeats will reset the radio.
OFF: Cellular receiver 3 will not be supervised. When disabled, heartbeat is not sent to the receiver. Supervisory
trouble is indicated.
Note: Cellular receiver 2 can not be supervised.
[3] Supervision Type Default (OFF)
ON: Heartbeat 1 (commercial supervision). This supervision type is suitable for applications where swap detection is
required on the supervisory packet.
OFF: Heartbeat 2 (residential supervision). This supervision type is suitable for applications where supervision of the
communication path to the receiver is required (no swap detection).
Note: Commercial supervision is more data intensive than residential supervision and should only be used when required
to meet the approval for the installation.
[4] Primary Path Default (OFF)
ON: Cellular channel is the primary path. Ethernet channel is the secondary path.
- 133 -
OFF: Ethernet channel is the primary path in a dual communicator. Cellular channel is the secondary path.
[6] Remote Firmware Upgrade Default (ON)
ON: The control panel firmware can be remotely upgraded using the Ethernet/cellular paths.
OFF: The control panel firmware can not be remotely upgraded. Local firmware upgrade is still possible.
[7] Alternate Test Transmissions Default (OFF).
ON: When the periodic test transmission interval occurs, the test transmission will alternate between being sent to the
primary and secondary receivers with each test transmission interval.
OFF: When the periodic test transmission interval occurs, the test transmission will be sent to the programmed receiv-
ers, based on the settings of the periodic test transmission reporting codes.
[8] Cellular Low Signal Trouble. Default (OFF)
This option masks the low signal trouble from generating cellular trouble.
ON: A cellular trouble event is generated when the radio signal level falls below threshold level (average CSQ level
is 4 or less).
OFF: A cellular trouble event is not generated when the radio signal level falls below threshold level (average CSQ
level is 4 or less).
[006] System Toggle Options 2
[1] Ethernet 1 receiver enabled. Default (ON)
ON: Ethernet receiver 1 is enabled.
OFF: Ethernet receiver 1 is disabled.
[2] Ethernet receiver 2 is enabled. Default (ON)
ON: Ethernet receiver 2 is enabled.
OFF: Ethernet receiver 2 is disabled.
[3] Reserved
[4] Cellular receiver 3 is enabled. Default (ON)
ON: Cellular receiver 3 is enabled.
OFF: Cellular receiver 3 is disabled.
[5] Cellular receiver 4 is enabled. Default (ON)
ON: Cellular receiver 4 is enabled.
OFF: Cellular receiver 4 is disabled.
[6] Reserved
[7] DLS Over Cellular. Default (ON).
ON: DLS is enabled on the cellular path.
OFF: DLS is disabled on the cellular path.
Note: Program this toggle as OFF to prevent DLS from using the cellular path.
Note: If this toggle is OFF, DLS sessions will occur on the Ethernet path only, regardless of the primary path set in section
[005] toggle option [4]. If it is ON, the communicator will connect to the primary path first for DLS and if the session fails, the
secondary path will be used.
[8] Network Trouble Suppression. Default (OFF).
ON: Cellular/Ethernet Supervisory troubles and restore signals follow delay timer as programmed in section [226].
OFF:Cellular/Ethernet Supervisory troubles and restore signals are sent immediately.
[007] DNS Server IP 1
Default (000.000.000.000)
Enter the IP address for DNS server 1. Format is 4 fields, each field is a 3-digit decimal. Valid range: 000-255.
Note: If no value is programmed and DHCP is used, the DHCP server will configure the address. If an address is pro-
grammed and DHCP is used, the programmed address will be used instead of the DHCP address.
Default (000.000.000.000)
- 134 -
Enter the IP address for DNS server 2. Format is 4 fields, each field is a 3-digit decimal. Valid range: 000-255.
Note: If no value is programmed and DHCP is used, the DHCP server will assign this value. If an address is programmed
and DHCP is used, the programmed address will be used instead of the DHCP address.
Programming Options
[010] System Toggle Options 3
[1] 2-Way Audio Over Cellular. Default (OFF)
ON: 2-Way Audio Over Cellular is enabled.
OFF: 2-Way Audio Over Cellular is disabled.
[2] Visual verification. Default (OFF)
ON: Visual verification is enabled.
OFF: Visual verification is disabled.
[3] Video On Demand. Default (OFF)
ON: Video On Demand is enabled.
OFF: Video On Demand is disabled.
[4] Receiver Group. Default (OFF)
ON: Receiver Group is enabled.
OFF: Receiver Group is disabled.
[5] Reserved.
[6] Reserved.
[7] Reserved.
[8] Reserved.
[012] DLS Incoming Port
Default (03062)
The DLS incoming local port (listening port) is the port DLS IV will use when connecting to the communicator. If a router or
gateway is used, it must be programmed with a transmission control protocol (TCP) port forward for this port to the com-
municator module IP address. Valid range: 00000 - 65535.
[013] DLS Outgoing Port
Default (03066)
The DLS outgoing port is used for outgoing sessions to DLS IV after an SMS request has been sent to the communicator.
Use this section to set the value of the local outgoing port. The value must be changed if the communicator is located behind
a firewall and must be assigned a particular port number, as determined by the network administrator. In most cases, chan-
ging the default value or configuring the firewall with this port is not required.
Note: If section [006] toggle option [7] is ON, DLS will use the primary path for session. If section [006] toggle option [7] is
OFF, DLS will use the Ethernet path, if available.
[015] DLS Call-Up IP
Default (000.000.000.000)
[016] DLS Call-Up Port
Default (00000)
[018] Receiver Group Pair
Default (0000)
Use the Receiver Group Pair to add two receivers to the receiver group in order to select which two receivers get the sim-
ulations event and visual verification communications. Use this option with the receiver group enable option [851][010] bit 4.
You can use any two available receiver paths. Valid range: 0000-FFFF.
[020] Time Zone
Default (00)
- 135 -
Refer tosection [024] 5 Real-Time Clock for more details. Use Column 2 (Offset Hours) to find the local Time Zone. Record
the two digit HEX value from Column 1 (HEX Value) on the same row. Program this HEX value for the Time Zone. Valid
range is 00 - FF.
Table 5-5 World Wide Time Zone
HEX Value Offset Hours Standard Abbreviation Location

01 -12 BIT Baker Island Time
05 -11 SST Somoa Standard Time
09 -10 HAST Hawaii-Aleutian Standard Time
0B -9.5 MIT Marquesas Island Time
0D -9 AKST Alaska Standard Time
11 -8 PST Pacific Standard Time
15 -7 MST Mountain Standard Time
19 -6 CST Central Standard Time
1D -5 EST Eastern Standard Time
1F -4.5 VST Venezuela Standard Time
21 -4 AST Atlantic Standard Time
23 -3.5 NST Newfoundland Standard Time
25 -3 ART Argentina Time
29 -2 BEST Brazil Eastern Standard Time
2D -1 CVT Cape Verde Time
31 0 GMT Greenwich Mean Time (UTC)
35 1 CET Central European Time
39 2 SAST South Africa Standard Time
3D 3 AST Arabic Standard Time
3F 3.5 IRST Iran Standard Time
41 4 GST Gulf Standard Time
43 4.5 AFT Afghanistan Time
45 5 PKT Pakistan Time
47 5.5 IST Indian Standard Time
48 5.75 NPT Nepal Time
49 6 VOST Vostok Time
4B 6.5 MMT Myanmar Time
4D 7 BDT Bangladesh Standard Time
51 8 CST China Standard Time
52 8.25 APO Apo Island Time
54 8.75 ACWST Australian Central Western Standard Time
55 9 KST Korea Standard Time
57 9.5 ACST Australian Central Standard Time
59 10 AEST Australian Eastern Standard Time
5B 10.5 LHST Lord Howe Standard Time
5D 11 VUT Vanuatu Time
- 136 -
HEX Value Offset Hours Standard Abbreviation Location

5F 11.5 NFT Norfolk Island Time
61 12 NZST New Zealand Standard Time
64 12.75 CHAST Chatham Island Standard Time
65 13 TOT Tonga Time
69 14 LINT Line Island Time
70-FF N/A N/A N/A
[025] Radio Activation Restore
Default (FF)
Program 00 to disable this event or FF to enable. This event will occur in North American cellular communicators when the
unit has been programmed by Connect 24.
System Test Options
Test Transmissions to Primary Receiver, with Backup to Secondary Receiver:
Set Ethernet section [026] to (FF); [027] to (00). Set cellular section [028] to (FF); [029] to (00).
l If the test transmission fails to the primary receiver it will back up to the secondary receiver.
l If the test transmission fails to the secondary receiver an FTC trouble will be generated.
Test Transmission Unique to Primary and Secondary Receivers:
Set Ethernet section [026] to (FF); [027] to (FF). Set cellular section [028] to (FF); [029] to (FF).
l The module will send periodic test transmissions to each receiver independently, with no backups.
l If the test transmission fails to any of the programmed receivers, an FTC trouble will be generated.
Alternate Test Transmission:
Alternate test transmission can be enabled or disabled in section [005] toggle option [7].
Alternate Test Transmission with Backup Receivers:
Set Ethernet section [026] to (FF); [027] to (00). Set cellular section [028] to (FF); [029] to (00).
Interval 1:
l If the test transmission fails to the primary receiver, it will back up to the secondary receiver.
l If the test transmission fails to the secondary receiver, an FTC trouble will be generated.
Interval 2:
l If the test transmission fails to the secondary receiver, it will back up to the primary receiver.
l If the test transmission fails to the primary receiver, an FTC trouble will be generated.
Test Transmission Unique to Primary and Secondary Receivers:
Set Ethernet section [026] to (FF); [027] to (FF). Set cellular section [028] to (FF); [029] to (FF).
Interval 1:
l The module will send periodic test transmissions to primary receivers (Ethernet primary and cellular primary) inde-
pendently, with no backups.
l If the test transmission fails to any of the programmed primary receivers, an FTC trouble will be generated
Interval 2:
The module will send periodic test transmissions to secondary receivers (Ethernet secondary and cellular secondary) inde-
pendently, with no backups.
l If the test transmission fails to any of the programmed secondary receivers, an FTC trouble will be generated
[026] Ethernet 1 Test Transmission
Default (FF)
Program 00 to disable this event transmission or FF to enable. See system test options (previous page) for details on set-
tings.
[027] Ethernet 2 Test Transmission
Default (00)
- 137 -
tings.
[028] Cellular Receiver 3 Test Transmission
Default (FF)
tings.
[029] Cellular Receiver 4 Test Transmission
Default (00)
tings.
Note: The time interval (in minutes) between periodic tests is programmed in section [125] (Ethernet) and section [225] (cel-
lular).
[030] FTC Restore
Default (FF)
Program 00 to disable this event transmission or FF to enable. This event will occur when an FTC Trouble on the system
restores.
[095] SA Incoming Local Port
Default (03092)
Valid range: 00000 - 65535
[096] SA Outgoing Local Port
Default (03093)
Valid range: 00000 - 65535
Ethernet Receiver 1 Options
[101] Ethernet Receiver 1 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between transmitters. This account code is used when trans-
mitting heartbeat signals to the central station receiver. Signals received from the panel will use the control panel account
number. Valid range: 0000000001-FFFFFFFFFE.
Note: If Ethernet receiver 1 and cellular receiver 1 are programmed as the same receiver (IP and port number are identical),
Ethernet receiver 1 account code will be used.
[102] Ethernet Receiver 1 DNIS
Default (000000)
The Dialed Number Information Service (DNIS) is used in addition to the account code to identify the communicator module
at the central station. Valid range: 000000 - 099999. Value is entered as a leading 0 followed by the 5 digit DNIS. Format is
Binary Coded Decimal (BCD).
Note: Each Ethernet/cellular receiver must be programmed with a unique DNIS.
[103] Ethernet Receiver 1 Address
Default (127.000.000.001)
The default address enables the communicator to operate in Unattended Mode.
Unattended mode is used when a receiver is not available and the unit is required to perform DLS sessions. Typically used
where the customer programs the control panel daily due to access control and still wants to receive alarms without buying
extra hardware (receiver) or software.
Note: When a valid IP address has been programmed, Ethernet receiver 1 is enabled and will communicate events over the
Ethernet channel.
Ethernet receiver 1 and cellular receiver 1 may be configured to communicate to the same central station receiver. To con-
figure the device to operate using this common receiver mode functionality, program Ethernet receiver 1 and cellular
receiver 1, IP address and port number with identical values.
Note: When operating in common receiver mode, Ethernet receiver 1 account code will be used for Ethernet and cellular.
- 138 -
[104] Ethernet Receiver 1 UDP Remote Port

Default (03061)
This Section determines the UDP remote port of Ethernet receiver 1. Valid range: 00000 - 65535.
[105] Ethernet Receiver 1 UDP Local Port
Default (03060)
Use this section to set the value of the UDP local outgoing port. Set the value of this port when the installation is located
behind a firewall and must be assigned a particular port number as determined by the central station system administrator.
Valid range: 00000 - 65535.
[106] Ethernet Receiver 1 Domain Name
Default ( )
Enter the domain name as 32 ASCII characters.
Ethernet Receiver 2 Options
[111] Ethernet Receiver 2 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between transmitters. The account code is used when trans-
mitting heartbeat signals to the central station receiver. Signals received from the control panel will use the control panel
account number. Valid range: 0000000001- FFFFFFFFFE.
Note: If both Ethernet receiver 2 and cellular receiver 2 are the same receiver (IP and port number are identical), Ethernet
receiver 2 account will be used for Ethernet and cellular.
[112] Ethernet Receiver 2 DNIS
Default (000000)
The DNIS is used in addition to the account code to identify the communicator module at the central station. Valid range:
000000 - 099999. Value is entered as leading 0 followed by the 5-digit DNIS. Format is BCD.
[113] Ethernet Receiver 2 Address
Default (000.000.000.000)
Programming the Ethernet receiver 2 IP address with 000.000.000.000 will disable Ethernet.
Enter the Ethernet receiver 2 IP address. This address will be provided by the central station system administrator. Format is
4 fields, each field is a 3-digit decimal. Valid range: 000-255.
Note: When a valid IP address has been programmed, Ethernet receiver 2 is enabled and will communicate events over the
Ethernet channel.
Ethernet receiver 2 and cellular receiver 2 may be configured to communicate to the same central station receiver.
To configure the device to operate using this common receiver mode functionality, program the Ethernet receiver 2 and cel-
lular receiver 2 IP address and port number with the same values. When operating in common receiver mode the Ethernet
receiver 2 account code will be used for communications over Ethernet and cellular.
Note: Do not program Ethernet receiver 1 and Ethernet receiver 2 to communicate to same receiver.
[114] Ethernet Receiver 2 UDP Remote Port
Default (03061)
This section is used to program the port number used by Ethernet receiver 2. Set the value of this port when the installation
is located behind a firewall, and must be assigned a particular port number as determined by the central station system
administrator. Valid range: 00000 - 65535.
Note: Do not program Ethernet receiver 1 and Ethernet receiver 2 port with the same value.
[115] Ethernet Receiver 2 UDP Local Port
Default (03065)
Use this section to program the value of the local outgoing port. Set et the value of this port when the installation is located
behind a firewall and must be assigned a particular port number as determined by the network administrator. Valid range:
00000 - 65535.
Note: Do not program Ethernet receiver 1 and Ethernet receiver 2 port with the same value.
- 139 -
[116] Ethernet Receiver 2 Domain Name

Default ( )
Enter the Domain Name as 32 character ASCII.
Ethernet Options
[124] Ethernet Test Transmission Time
Default (9999)
Enter a 4 digit number (0000-2359) using the 24-hour clock format (HHMM) to set the test transmission time of day. Valid
range: 00 - 23 hours (HH) and 00 - 59 minutes (MM). Programming a value of 9999 will disable the test transmission time.
Note: The internal date and time will automatically be programmed when the unit communicates with the primary receiver.
[125] Ethernet Test Transmission Cycle
Default (000000)
This value represents the interval between test transmissions, in minutes. Valid range: 000000 - 999999 minutes. Once the
unit has sent the initial periodic test transmission, all future test transmissions will be offset by the programmed number of
minutes. See sections [026] - [029].
Table 5-6 Ethernet Test Transmission Interval
Test Transmission Interval Daily Weekly Monthly
Programmed Minutes 001440 010080 043200
Note: Minimum value is 000005 minutes. Programming an interval that is less than 5 minutes will disable test transmission.
Cellular Receiver 3 Options
[201] Cellular Receiver 3 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between transmitters. This account code is used when trans-
mitting heartbeat signals to the central station receiver. Signals received from the control panel will use the control panel
account number. Valid range: 0000000001 - FFFFFFFFFE.
[202] Cellular Receiver 3 DNIS
Default (000000)
000000 - 0FFFFF Values are entered as a leading 0 followed by the 6-digit DNIS.
[203] Cellular Receiver 3 IP Address
Default (000.000.000.000)
Enter the cellular receiver 1 IP address. This information will be provided by the central station system administrator. Each 3-
digit segment of the address must be within a valid range of 000-255.
Note: When a valid IP address has been entered, the cellular receiver is enabled and will communicate events over the cel-
lular channel.
[204] Cellular Receiver 3 Port
Default (03061)
This section determines the port used by cellular receiver 3. Change the default value of this port when the installation is loc-
ated behind a firewall and must be assigned a particular port number as determined by the central station system admin-
istrator. Valid range: 00000 - 65535.
Note: Programming this section with 00000 will disable the receiver.
[205] Cellular Receiver 3 APN
Default ()
The Access Point Name (APN) determines the cellular network that the communicator will connect to. This information is
available from the network carrier. Program this section as 32 ASCII characters.
Note: When a SIM card with a custom APN is used, the unit will not have access to the Internet. DLS and remote flash can
still be done if section [221] is programmed with a valid public APN.
- 140 -
[206] Cellular Receiver 3 Domain Name

Default ( )
Enter the Domain Name as 32 ASCII characters. This information will be provided by the central station system admin-
istrator.
Cellular Receiver 4 Options
[211] Cellular Receiver 4 Account Code
Default (0000000000)
The account code is used by the central station to distinguish between different transmitters. This account code is used when
transmitting signals to the central station receiver. Signals received on the panel will use the panel account number. Valid
range: 0000000001 - FFFFFFFFFE.
[212] Cellular Receiver 4 DNIS
Default (000000)
000000 - 099999. Values are entered as a 0 followed by the 6-digit DNIS value. Format is BCD.
[213] Cellular Receiver4 IP Address
Default (000.000.000.000)
Enter the cellular receiver 4 IP address. This IP address will be provided by the central station. Format is 4 fields, each field
is 3-digit decimal. Valid range: 000 - 255.
Note: When a valid address has been entered, cellular receiver 2 is enabled and will communicate events over the cellular
path.
[214] Cellular Receiver 4 Port
Default (03061)
This section defines the port of cellular receiver 4. Change the value of this port when the installation is located behind a fire-
wall and must be assigned a particular port number, as determined by the central station system administrator. Valid range:
00000 - 65535.
Note: Do not program cellular receiver 1 and cellular receiver 2 to communicate to the same receiver.
[215] Cellular Receiver 4 APN
Default ( )
The APN determines the cellular network that the communicator will connect to. This information is available from the net-
work carrier. Program this section with up to 32 ASCII characters.
Note: When a SIM card with a custom APN is used, the unit will not have access to the Internet. DLS and remote flash can
still be done if section [221] is programmed with a valid public APN.
[216] Cellular Receiver 4 Domain Name
Default ( )
Enter the cellular receiver 2 Domain Name with up to 32 ASCII characters.
Cellular Options
[221] Cellular Public Access Point Name
Default ( )
When the communicator is operating on a private APN, use this section to select a public APN for DLS and remote firmware
update. This information is available from the network carrier. The APN identifies the public cellular network that the com-
municator will connect to.
[222] Cellular Login User Name
Default ( )
Some network carriers require login credentials when connecting to an APN. Program the login user name in this section.
Enter the Cellular Login User Name with up to 32 ASCII characters.
[223] Cellular Login Password
Default ( )
- 141 -
Some network carriers require login credentials when connecting to an APN. Program the login Password in this Section.
Enter the Cellular Login Password with up to 32 ASCII characters.
[224] Cellular Test Transmission Time of Day
Default (9999)
Enter a 4 digit value using the 24-hour clock format (HHMM) to set the test transmission time of day. Valid range: 00-23 for
the hours (HH) and 00-59 for the minutes (MM).
Note: To disable the test transmission time of day enter 9999 or FFFF in this section.
The internal date and time will be automatically programmed by the primary receiver only.
[225] Cellular Test Transmission Cycle
Default (000000)
This value represents the interval in between test transmissions in minutes. Valid range: 000000 - 999999 minutes. Once the
unit has sent the initial periodic test transmission, all future test transmissions will be offset by the programmed number of
minutes. See sections [026] - [029].
Table 5-7 Cellular Test Transmission Interval
Test Transmission Interval Daily Weekly Monthly
Programmed Minutes 001440 010080 043200
Note: Minimum value is 000005 minutes. Programming an interval that is less than 5 minutes will disable test transmission.
[226] Network Trouble Delay Timer
Default (015)
This option is used to program the delay, in minutes, for reporting a cellular trouble delay. Valid entries are 000 - 255. When
this section is programmed as 00, Cellular, Ethernet and Supervision troubles are not communicated.
[227] Voice Call Timeout
Default (000) Valid entries are 000 - 255.
[228] Voice Call Back Time
Default (010) Valid entries are 000 - 255.
[229] Voice Call Back Number
Default ( ) 32 digit phone number.
Valide entries:: 0000000000000001 to FFFFFFFFFFFFFFFE
[422] Integration Identification Number
This section will display the unique 12-digit number assigned to this control panel for the identification when integrated with
third party applications.
[423]Session 1 Integration Access Code
Default (12345678123456781234567812345678) Valid Range is 0000000000000000 - FFFFFFFFFFFFFFFF.
This section is a programmable 32-digit number used for initialization with third party applications.
Note: If integrating with a third party application, this Access Code field must be programmed to a unique number in oder to
secure the connection with 128 bit encryption.
[424] Session 1 SMS Label
Default (11111111)
This section is used to identify the integration session with a third party integrator.
[425] Session 1 Integration Toggle Options 2
The toggle options in this section are used to enable and configure the path used for integration with third party applications.
[1] Integration over USB Default (OFF)
[2] Integration over Cellular Default (OFF)
[3] Integration over Ethernet Default (OFF)
[4]ITv2 Integration Protocol Default (ON)
- 142 -
[426]Session 1 Integration Toggle Options 3

The toggle options in this section are used to determine the polling and notification behavior used for integration with third
party applications.
[1] UDP Polling Default (OFF)
[2] TCP Polling Default (OFF)
[3] Real-time Notification Default (OFF)
[4] Notification Follows Poll Default (OFF)
[5] Firewall IP Default (OFF)
[427] Session 1 Interactive Polling Interval in Seconds
Default (00010) Valid range: 00000-65535
This option controls the polling interval from the alarm panel to the integration interface for the purpose of optimizing data
usage. The shorter the interval, the higher the data usage.
[428] Session 1 Integration Server IP
This section programs the IP address of the third party server. Do not program this section if a domain name is programmed
in setion [431].
[429] Session 1 Integration Notification Port
Default (00372) Valid range: 00000-65535
This section is used to program the TCP Integration port for real time notification
[430] Session 1 Integration Polling Port
Default (00373) Valid range: 00000- 65535
This section is used to program the integration server port. Refer to third party device manual for more information
[431] Session 1 Integration Server DNS
Enter the domain name (up to 32 ASCII characters) as provided by a third-party device. Refer to third party device manual for
more information.
[432] Session 1 Integration Outgoing Port
This section is used to program the outgoing port for integration via UDP.
[433]Session 1 Integration Incoming Port
This section is used to program incoming port for integration via TCP.
[450]-[460] Repeats [423]-[433] for Session 2
[691] - [694] Session 1 to 4 Notification Control
[1] - Alarm and Alarm Restore Notifications Off (ON)
[2] - Tamper and Tamper Restore Notifications Off (ON)
[3] - Arming/Disarming Notifications (ON)
[4] - Trouble and Trouble Restore Notifications (ON)
[5] -Test Transmission Notifications (ON)
[901] Receiver Test
This section is used to enable Ethernet or cellular ports for receiver diagnostic test transmissions.
[1] Receiver 1 Default (OFF)
System Information (Read Only)
Note: Provided for information (read-only). Values in these sections cannot be modified by the installer.
- 143 -
[976] - Radio Configuration File Version

[977] - Cellular Network Provider - MCC/MNC Code
[978] - Cellular Network Type
00 GPRS 2G 04 LTE Ethernet only
01 EDGE 2G 05 LTE Advanced LTE
02 WCDMA 3G 06 CDMA LTE ADVANCE
03 HSDPA CDMA 07 EVDO WCDMA
[979] - Cellular Network CSQ

[980] - Radio Reset Codes
[981] - Radio Type
[982] - Radio Firmware Version
[983] - Firmware Update Diagnostics Section
Firmware updates for panel and the communicator itself can be made from the communicator.
Table 5-8 Response Code Descriptions and Corresponding Actions
Description of Response
Response Code Code Corresponding Action
Bad File
00 Version check failed Contact DSC Tech Support, described the
01 Image type mismatch action attempted with the system and supply
them with the Response Code in Section
02 Device type mismatch [983].
03 Hardware type mismatch
04 General variant mismatch
05 Firmware header wrong length
Panel is Busy
20 System update pending - Disarm the panel to continue with system
panel is armed firmware update process.
21 System update pending -AC Resolve the AC trouble to continue with sys-
trouble (Any AC trouble; tem firmware update process.
device/module)
22 System update pending -low Resolve the low battery trouble to continue
battery (Any low battery with system firmware update process.
trouble; device/module)
25 System update pending - com- Retry in a few minutes; if issue persists, con-
munication in progress tact DSC Tech Support.
Firmware Update Sequence Change
A0 System firmware update suc- None
cessful
A1 System firmware update fail- At least one module was not updated. Use
ure DLS to reapply the firmware to the module
not updated.
A2 System firmware update fail- At least one module was not responding dur-
ure - module not found ing firmware update. Ensure all modules
enrolled are physically connected and
powered up.
AA Device firmware transfer begin None
- 144 -
Description of Response
Response Code Code Corresponding Action
AB Device firmware module None
update begin
AC General device firmware trans- Contact DSC Tech Support, describe the
fer failure action attempted with the system and supply
them with the Response Code in Section
[983].
Firmware Update Status
C0 System ready to update None
C1 System update cancel request The system has received an update cancel
received request from DLS.
C2 System update begin None
Firmware Download Request Reject
E0 Reserved
E1
E2
E3
E4
E5 Remote firmware update dis- Enable remote firmware update in the com-
abled municator in order to perform remote system
firmware update.
Local Status Update States
FE Firmware file empty No action required. Communicator currently
does not have any firmware files.
FD Firmware download in pro- No action required. Communicator is cur-
gress rently downloading firmware.
The table displays firmware update indicator codes and meaning of each code. The updates can be made from com-
municator. The communicator can update firmware of the panel and also of the communicator itself. This section does not
provide specific details such as if the image is still stored or erased due to the cancellation code.
[984] - Communicator Status
The communicator status sections provide the installer with the status of the communicator’s functionality, operational read-
iness, and failures.
The communicator status is displayed as a 6-digit hexadecimal code. The code ranges between 00000F and 2220CF,
though not all numbers in this range are assigned. Each of the 6 digits represents a status or trouble indicator as below:
1. Digits 1 and 2: Signal strength indicators display the presence/strength of cellular radio.
2. Digit 3: Network Indicator, indicates the operational status of the network.
3. Digits 4 and 5: Trouble Indicator displays the type of issue on the communicator or modules associated with and con-
nected to the communicator. See Table 8 on page 17 for a listing of possible values.
4. Digit 6: Reserved, displays as ‘F’ or ‘-’.
For example, a value of 11002F means:
11- Signal strength is excellent
0 - No network issues
02 - Panel supervision trouble with the communicator
The status code for the radio signal strength, its typical troubles, possible causes and troubleshooting instructions is dis-
played in the following table.
- 145 -
Table 5-9 Radio Signal Strength - Digits 1 and 2

Signal
Signal CSQ Signal Indic- Signal Indic- Signal Level Level
Strength Level ator 1 ator 2 [dBm] Status Action Required
No Signal 0 0 0 -108.8 bad Check all antenna connections.
Confirm cellular service is active in area.
Relocate panel or install external antenna.
1 Bar 1-4 0 2 -108 ~ -103 weak Relocate panel or install external antenna if yel-
2 Bars 5-6 0 1 -102 ~ --99 weak low trouble LED has 5 flashes.
3 Bars 7 - 10 2 1 -98 ~ -91 strong Location is OK. Cellular signal strength is

4 Bars 11 - 13 2 1 -90 ~ -85 strong greater than CSQ 7.
5 Bars 14 + 1 1 -84 and excellent

higher
Table 5-10 Network Indicator - Digit 3
Network Indicator Value Means
OFF No network trouble
ON Ethernet cable disconnected
Ethernet DHCP failed
Flashing Incoming transmission
Outgoing transmission
Incoming transmission
[985] - Radio Initialization Status
The radio initialization status provides installers with the status of radio communication. It is displayed as an 8-digit toggle
option, with each digit indicating a task in the initialization process.
1. Radio power up
2. Received the SMS from C24 Communications
3. Radio reset
4. Radio attached to network
5. Receiver 1 initialized
For example, the radio initialization status code 12-45--- indicates that radio has been powered up, it has received SMS sig-
nal from C24 Communications, the radio is attached to the network, and receiver 1 has been initialized. This code would
update to 12-45678 when receivers 2, 3, and 4 are initialized.
If the radio initialization status code does not indicate any problems, proceed with installation as per this manual. If troubles
are reported, reset the initialization process. If this action does not fix the problem, refer to the trouble shooting section in this
manual.
The following table shows each digit position in the status code, each digit’s value and its assigned meaning in the eight-
digit code:
Table 5-11 Radio Initialization Status - 1-8 bits completion
Bit 1 2 3 4 5 6 7 8
Not Completed - - - - - - - -
Completed 1 2 3 4 5 6 7 8
[986] - Options 4
[1] Remote Shutfown Default (OFF)
- 146 -
[987] - Language Version

This section will display the current language version of the communicator.
[988] - DNS 1 IP
This section will display the IP address of DNS Server 1. This is useful when the unit is configured for DHCP and the IP
address assigned to the device by the DHCP Server is needed. This value is programmed in Section [007] or assigned by
DHCP.
[989] - DNS 2 IP
This section will display the IP address of DNS Server 2. This is useful when the unit is configured for DHCP and the IP
address assigned to the device by the DHCP Server is needed. This value is programmed in section [008] or assigned by
DHCP.
[990] - Boot Loader Version
This section will display the current boot loader version of the communicator.
[991] - Firmware Version
This section will display the current firmware version of the device. Update worksheets with new version after a flash update
is completed.
[992] - Ethernet IP Address
This section will display the IP address of the Ethernet connection. This value is programmed in section [001] or assigned by
DHCP.
[993] - Ethernet Gateway IP Address
This section will display the IP address of the Ethernet connection. This value is programmed in section [001] or assigned by
DHCP.
[994] - Cellular IP Address
This section will display the current dynamic IP address assigned by DHCP to the cellular connection.
Note: Cellular uses DHCP (dynamic IP) only. The cellular IP address is always provided by the cellular network (i.e., not pro-
grammable).
[995] - SIM Number
This section will display the Subscriber Identity Module (SIM) number of the SIM card installed in the communicator. Format
is: Major Industry Identifier (2 digits); Mobile Country Code (2 or 3 digits); Mobile Network Code (2 - 3 digits); Unique Number
(10 - 12 digits); and Checksum (1 digit). Valid SIM numbers range is: 18 - 21 numbers. Thisnumber is printed on the SIM and
the outside of the communicator carton.
Note: The checksum digit is omitted on 19-digit SIM card numbers.
[996] - Cellular Telephone Number
This section will display the cellular telephone number of the SIM. This telephone number is required by the Installer for DLS
and remote firmware (flash) update.
[997] - IMEI Number
This section will display the unique 15-digit International Mobile Equipment Identity (IMEI) of the radio. Format is: Reporting
Body Identifier (2 digits), Allocation Number (4 digits); Final Assembly Code (2 digits); Serial Number (6 digits); and a check
digit.
[998] - MAC Address
This section will display the unique12-digit, hexadecimal number assigned as the Media Access Control (MAC) address of
the device.
[860] Display Keypad Slot Number
The 2-digit slot number of the keypad being used is displayed in this read only section.
[861]-[876] Keypad Programming
Use section [861] to [876] to configure keypads 1 to 16. For information on keypad programming, refer to the installation
sheet supplied with the keypad.
EN Note: For EN50131 compliant installations [861][021] options 1 and 2 must be disabled.
- 147 -
[899] Template Programming

Template programming allows quick programming of the minimum functions required for basic operation. This section is
used to view current template programming options and to define certain system parameters. Press the (#) key to accept the
displayed value and advance to the next option. The following options are available:
l 5-digit Template Code: Displays the current 5-digit template programming code (default: 00000). Each digit in the
code selects a set of pre-defined programming options, as described below:
l Digit 1 - zone 1-8 definition options
l Digit 2 - system EOL options
l Digit 3 - alarm controller communications options
l Digit 4 - reporting code configurations
l Digit 5 - DLS connection options
l Central Station Telephone Number: The phone number used to contact the central monitoring station (32 character
limit).
l Central Station Account Code: The account code used in programming section [310]. This is a 4 or 6-digit entry.
l Partition Account Code: Used to identify partition-specific events. All 4 digits must be entered in order to complete the
entry.
l This account code is entered into programming section [310][001].
l DLS Access Code: The 6-digit DLS access code used in programming section [403].
l Partition 1 Entry Delay: The 3-digit entry delay duration for partition 1, in seconds, used in programming [005][001]
option 1.
l Partition 1 Exit Delay: The 3-digit exit delay duration for partition 1, in seconds, used in programming section [005]
[001] option 3.
l Installer Code: The 4, 6 or 8-digit installer access code used in programming section [006][001].
For more information on template programming, see "Template programming tables" on page 258.
Systems Information
[900] System Information
[000] – Control Panel Version
This read-only section contains the model number, software version, hardware revision and serial number of the alarm con-
troller. For example, an entry of 1234 is read as version 12.34.
[001]-[524] – Module Information
This read-only section is used to view the model number, software version, and hardware revision information of the mod-
ules enrolled on the alarm system.
To view information for a specific module, scroll to the corresponding section:
[001]-[016] keypads
[101]-[130] 8-zone expansion module
[201]-[216] 8-output expansion module
[301] -[330] 8 zone expansion module
[460] Alternate Communicator
[461] HSM2Host module
[481] 2 Way Audio Module
[501]-[504] 1A power supply module
[521]-[524] high-current output modules 1-4
[551]-[554] 3A power supply
[601]-[608] Corbus repeater
[901] Installer Walk Test Mode Enable/Disable
This mode tests the operation of each detector in the system. Enter section [901] to initiate a walk test. While in Walk Test
mode, the Ready, Armed, and Trouble LED's on the keypad flash to indicate that the test is active. When a zone is tripped
during the test, a 2-second tone sounds on all system keypads to indicate that the zone is working correctly.
- 148 -
After 10 minutes without zone activity, the alarm system emits 5 beeps every 10 seconds from all keypads. After another 5
minutes of inactivity, Walk Test terminates automatically.
To manually exit walk test mode, enter [901] again.
Module Programming
Use this section to add, remove and confirm the following modules:
l Keypads see "Compatible devices" on page 8
l 8-zone expander module (HSM2108)
l 8-output expander module (HSM2208)
l Power supply (HSM2300)
l 4-output power supply (HSM2204)
l Wireless transceiver (HSM2HOSTx)
l Audio Verification Module (HSM2955)
l 8 zone Expansion Module (HSM3408)
l Power Supply Module (HSM3350)
l Corbus Repeater Module (HSM3204CX)
Once added, modules are supervised by the system.
[902] Add/Remove Modules
Modules can be enrolled automatically our manually. In either case, the serial number of the device is used as an identifier.
Select one of the enrollment options described below.
[000] – Auto Enroll Modules
When this mode is selected, the alarm system automatically enrolls all modules connected to the Corbus. The total number
of modules currently enrolled are displayed on the keypad.
l Enter sub-section [000] to begin auto enrollment of all new modules. The auto enroll screen will show the following:
l KP = Number of keypad type modules
l IO = Number of zone and output type modules
l M = Number of other type modules
Devices are assigned to the next available slot. The slot assignment can be modified using subsections [002] and
[003].
[001] – Enroll Modules
To enroll modules individually:
1. Enter programming section [902][001].
2. When prompted, key in the serial number of the module found on the PCB. An error tone is sounded if an invalid serial
number is used.
3. To cancel enrollment of a module, press [#].
[002] – Module Slot Assignment
This section is used to change the slot number a module is enrolled in. To change the slot number:
2. Key in the serial number of the module.
3. When prompted, key in the new two-digit slot number. The previous slot assignment is replaced with the new one. An
error tone sounds if an invalid slot number is keyed in.
[003] – Edit Module Slot Assignment
Like [002], this section is also used to change the slot number of a module. With this option, however, the serial number is
not required. To change the slot number:
2. Use the scroll keys to locate the module then press [*] to select.
3. Key in the new two-digit slot number. The previous slot assignment is replaced with the new one. An error tone sounds if
an invalid slot number is keyed in.
- 149 -
Deleting Modules
The following sections are used to remove modules from the system:
[101] – Keypads
[102] – 8-zone Expander Modules
[103] – 8-output Expander Modules
[104] – 8 zone HSM3408 Expander Module
[106] – HSM2Host
[108] – HSM2955
[109] – Power Supply
[110] – 4 High Current Output
[111] – 3A Power Supply Module
[112] – Corbus Repeater Module
1. After entering section [902], scroll to the module type you want to delete (101-112).
2. Press [*] to select the module type then scroll to the specific module you want to delete.
3. Press [*] to select the module then, when prompted, press [*] again to delete.
[903] Confirm Module
The following sections are used to confirm enrollment of individual modules, their serial and slot numbers, and to locate
them physically:
[000] – View All Modules
[101] – Keypads
[102] – 8-zone Expander Modules
[103] – 8-output Expander Modules
[104] – 8 I/O Expander Module
[106] – HSM2Host
[108] – HSM2955
[109] – Power Supply
[110] – 4 High Current Output
[111] – 3A Power Supply Module
[113] – Corbus Repeater Module
To confirm a module:
1. Enter section [903]>[000] to view all enrolled modules or scroll to the module type you want to confirm (101-113).
2. Press [*] to select the module type then scroll to the specific module you want to confirm. Press [*] to enter Confirmation
mode. The module’s serial number and slot number are displayed on the keypad and the status LEDs on the device flash.
This continues until confirmation mode for the device is exited via the [#] key.
Note: Keypad Blanking (section [016], option 3) must be disabled to confirm keypads.
Testing
[904] Wireless Placement Test
This test is used to determine RF signal status for wireless devices and can be performed at a system keypad or at the indi-
vidual device. These instructions pertain to testing at the keypad. For instructions on placement testing at the device, refer to
the installation sheet included with the wireless equipment.
The following test modes are available:
[001]-[248] Placement Test Zones 1-248
Test wireless devices individually by zone.
[521]-[528] Placement Test Repeaters 1-8
Test each enrolled wireless repeater.
- 150 -
[551]-[566] Placement Test Sirens 1-16

Test each enrolled wireless siren.
[601]-[632] Placement Test Wireless keys 1-32
Test individual wireless keys. Once in this section, press a button on the wireless key to begin the test.
[701]-[716] Placement Test Wireless Keypads 1-16
Test each enrolled wireless keypad.
Two test results are provided:
l 24-hour: Average status results received during a 24-hour period.
l Now: Signal status results of the current test.
The following status indicators may be displayed:
Table 5-12 Wireless Device Status Indications
Keypad Status
Strong Strong signal strength
Good Good signal strength
Poor Poor signal strength
1-Way The device is operating in 1-way mode only. The alarm panel cannot configure or control the device
Not Test Displayed as the Now result if no test was performed
None Always displayed as the 24-hour result when testing wireless keys
[911] Diagnostics
This Diagnostics feature provides a live measurement of voltage, current, and battery condition for the alarm panel and
devices through the system keypad. This information can be used in place of a multimeter to troubleshoot panel and module
troubles. To view specific measurements, scroll to the corresponding section:
[000] Panel
[001] DC input voltage/current
[002] Battery voltage, battery charge voltage/current, battery discharge voltage
[003] Aux supply voltage/current
[004] Bus supply voltage/current
[005] Main bell voltage/current
[006] Zone resistance-Zone 1-8
[001]-[130] Keypad 1-16
[001] Bus supply voltage
[002] I/O 1-Zone XXX resistance, where XXX is the zone number
[101]-[115] HSM2108 Zone expander
[003] I/O 1-8 resistance - Zones 1-8
[301]-[330] 8 I/O expander
[001] Zone resistance - Zones 1-8
[501]-[504] 1 A Power supply
[001] Battery voltage/current
[521]-[524] 4 Output 1 A power supply
[001] Battery voltage/current
[551]-[554] 3 A power supply
[001] DC input
[002] Battery voltage, battery charge voltage/current, battery discharge current
- 151 -

[005] Aux1 supply voltage/current
[006] Aux2 supply voltage/current
[601]-[608] Corbus repeater
[001] DC input
[004] Bus out voltage/current
[912] Soak Test
This feature is used to diagnose false alarms. After a false alarm has occurred on a zone, Soak Test mode impedes any aud-
ible alarm conditions or additional false alarm reporting. A record of the false alarm is stored in the event buffer for diagnostic
purposes.
[000] – Soak Test Duration
This option is used to program the length of time the system remains in soak test. The default is 14 days.
[001]-[248] Zone Soak Test
Soak test can be performed on individual zones. The zone remains in soak test, regardless of the status of the system, until
the soak test timer has expired. If the system is armed when the timer expires, the zones are removed from soak test when
the system is disarmed.
No communications occur for events from a zone in soak test, with the exception of low battery and low battery restore
events and faults generated by low sensitivity in a smoke detector.
A message indicating that the zone is in soak test is displayed when scrolling left or right in the base disarmed keypad
menu.
Note: Soak test is not applied to temperature detector events if it is enabled.
[982] Battery Settings
[000] – Panel Battery Settings
01 – When disabled, the panel battery is charged at 400 mA. When enabled, the battery is charged at 700 mA.
[010] – High Current Output Battery
Enables and disables the high-current battery charge option for HSM2204 1-4.
[020] – 1 A Power Supply Battery
Enables and disables the high-current battery charge option for HSM2300 1-4.
[030] – Corbus Repeater
Enables and disables the high-current battery charge option for HSM3204CX 1-8.
[040] – 3A Power Supply
Enables and disables the high-current battery charge option for HSM33501-4.
Toggle 1 enables high charge for battery 1.
Toggle 2 enables high charge for battery 2.
Toggle 3 enables or disables battery 2. Default is enabled.
Defaults
[989] Default Master Code
This section is used to default the master code to the factory default. After entering this section, key in the installer code then
989.
[989][installer code][989] or [*].
- 152 -
EN
Note: Feature is only available for models.
[990] Installer Lockout Enable/Disable
When this option is enabled, an installer can not perform a hardware default; attempts to do so are logged to the event buf-
fer.
An audible indication of installer lockout is provided when powering up the alarm system (the phone line relay clicks rap-
idly). Software default changes can still be made while installer lockout is enabled.
[990][installer code][990] or [*].
[991] Default Keypads
This programming option is used to return system keypads to factory default settings.
[901]- [916] – Default Keypads 1-16
This section resets individual keypads to factory defaults. After entering this section, select the keypad to default, key in the
installer code then 991 (or press [*]).
[999] – Default All Keypads
This section resets all system keypads to factory defaults. After entering this section, key in the installer code then (*) or 991.
[996] Default Wireless Receiver
This section resets the wireless receiver (HSM2HOSTx) to factory defaults. Enter [996][installer code][996 or *].
[998] Default HSM2955
This section resets the audio module (HSM2955) to factory defaults. Enter [998][installer code][998 or *].
[999] Default System
This section resets the alarm controller to factory defaults. Enter [999][installer code][999 or *].
- 153 -
Section 6: Programming Worksheets

EN
Note: listed options are required for EN 50131 Compliant Installations.
6.1 Label Programming
[000] Label Programming

Description on page 75
[000] – Language Selection (2-digit decimal; Default: 01)
01 – English 06 – Dutch 11 – Swedish 16 – Turkish 22 – Bulgarian
27 – Serbian
02 – Spanish 07 – Polish 12 – Norwegian 18 – Croatian 23 – Latvian
28 – Estonian
03 – Portuguese 08 – Czech 13 – Danish 19 – Hungarian 24 – Lithuanian
29 – Slovenian
04 – French 09 – Finish 14 – Hebrew 20 – Romanian 25 – Ukrainian
05 – Italian 10 – German 15 – Greek 21 – Russian 26 – Slovakian
[000] [001] Zone Labels (2 x 14 Characters)

001: 002: 003:
004: 005: 006:
007: 008: 009:
010: 011: 012:
013: 014: 015:
016: 017: 018:
019: 020: 021:
022: 023: 024:
025: 026: 027:
028: 029: 030:
031 032: 033:
034: 035: 036:
037: 038: 039:
040: 041: 042:
043: 044: 045:
046: 047: 048:
049: 050: 051:
052: 053: 054:
055: 056: 057:
058: 059: 060:
061: 062: 063:
064: 065: 066:
067: 068: 069:
070: 071: 072:
073: 074: 075:
076: 077: 078:
- 154 -
079: 080: 081:

082: 083: 084:
085: 086: 087:
088: 089: 090:
091: 092: 093:
094: 095: 096:
097: 098: 099:
100: 101: 102:
103: 104: 105:
106: 107: 108:
109: 110: 111:
112: 113: 114:
115: 116: 117:
118: 119: 120:
121: 122: 123:
124: 125: 126:
127: 128: 129:
130: 131: 132:
133: 134: 135:
136: 137: 138:
139: 140: 141:
142: 143: 144:
145: 146: 147:
148: 149: 150:
151: 152: 153:
154: 155: 156:
157: 158: 159:
160: 161: 162:
163: 164: 165:
166: 167: 168:
169: 170: 171:
172: 173: 174:
175: 176: 177:
178: 179: 180:
181: 182: 183:
184: 185: 186:
187: 188: 189:
190: 191: 192:
193: 194: 195:
196: 197: 198:
199: 200: 201:
202: 203: 204:
- 155 -
205: 206: 207:

208: 209: 210:
211: 212: 213:
214: 131: 215:
216: 217: 218:
219: 220: 221:
222: 223: 224:
225: 226: 227:
228: 229: 230:
231: 232: 233:
234: 235: 236:
237: 238: 239:
240: 241: 242:
243: 244: 245:
246: 247: 248:
[000] 064 – CO Alarm Message (2 x 14 Characters):
065 – Fire Alarm Message (2 x 14 Characters):
066 – Fail to Arm Event Message (2 x 16 Characters):
067 – Alarm When Armed Event Mes-

(2 x 16 Characters):
sage
100 – System Label (1 x 14 Characters):
101 – Partition 1 Label (1 x 14 Characters):
201 – Partition 1 Command Output

001 – Partition 1 Command Output 1:
Labels
(2 x 14 Characters) 002 – Partition 1 Command Output 2:
Descriptions on page 77 003 – Partition 1 Command Output 3:
Labels
- 156 -

Labels
Labels
Labels
Labels
Labels
Labels
(2 x 14 Characters):
601 – Schedule 1 Label
Descriptions on page 77
602 – Schedule 2 Label (2 x 14 Characters):
603 – Schedule 3 Label (1 X 16 Characters):
604 – Schedule 4 Label (1 X 16 Characters):
[000] 801 – Keypad Labels (1 X 14 Characters) Description on page 77

001 – Keypad 1 Label: 009 – Keypad 9 Label:
- 157 -

802 – HSM2108 Zone Expander Label Description on page 77
001– Zone Expander 1 Label: 016– Zone Expander 16 Label:
803 – HSM2208 Output Expander Label (1 X 14 ASCII) Description on page 77
001– Output Expander 1 Label: 009– Output Expander 9 Label:
804 – HSM3408 8 I/O Expansion Label (1 X 14 ASCII) Description on page 78
001– 8 I/O Expansion 1 Label: 016– 8 I/O Expansion 16 Label:
006– 8 I/O Expansion 6 Label: 021 – 8 I/O Expansion 21 Label:
014 – 8 I/O Expansion 14 Label: 029– 8 I/O Expansion 29 Label:
015– 8 I/O Expansion 1 5 Label: 030– 8 I/O Expansion 30 Label:
- 158 -
806 – HSM2HOSTx Label:

[000]
(1 X 14 Characters) Description on page 78
808 - HSM2955 Audio Module Label:
809 – HSM2300 Power Supply Label 001 – Power Supply 1 Label:
(1 X 14 Characters) 002 – Power Supply 2 Label:
003 – Power Supply 3 Label:
004 – Power Supply 4 Label:
810 – HSM2204 High-Current Output Supply Label 001 – High-Current Output Supply 1 Label:
(1 X 14 Characters) 002 – High-Current Output Supply 2 Label:
Description on page 78 003 – High-Current Output Supply 3 Label:
004 – High-Current Output Supply 4 Label:
811 – HSM3350 3A Power Supply Label 001 – 3A Power Supply 1 Label:
(1 X 14 Characters) 002 – 3A Power Supply 2 Label:
003 – 3A Power Supply 3 Label:
004 – 3A Power Supply 4 Label:
812 – HSM3204CX Corbus Repeater Label 001 - Corbus Repeater 1 Label:
(1 X 14 Characters): 002– Corbus Repeater 2 Label:

003– Corbus Repeater 3 Label:
007–Corbus Repeater 7 Label:
815 – Alt. Comm Label:
(1 X 14 ASCII) Description on page 78
[000] 820 – Siren Labels

001– Siren 1 Label: 009– Siren 9 Label:
[000] 821 – Repeater Label 001– Repeater 1 Label:

(1 X 14 Characters): 002– Repeater 2 Label:
Description on page 78 003– Repeater 3 Label:
004– Repeater 4 Label:
- 159 -

[000] 999 – Default Labels

6.2 Zone Setup
[001] [001 - 248] Zone Type

Available Zone Types
Default = 000
* Not UL evaluated
000 – Null Zone
018 – 24-Hour Bell/Buzzer
001 – Delay 1
023 – 24-Hour Supervisory 051 – 24-Hour Latching Tamper
002 – Delay 2
024 – 24-Hour Supervisory Buzzer 052 – 24-Hour Non-Alarm
003 – Instant
025 – Auto Verified Fire 056 – 24-Hour High Temperature
004 – Interior
027 – Fire Supervisory 057 – 24 Hour Low Temperature
005 – Interior Stay/Away
040 – 24-Hour Gas 060 – 24-Hour Non-Latching Tamper
006 – Delay Stay/Away
041 – 24-Hour CO 061 – 24-Hour Anti-Masking
007 – Delayed 24-Hour Fire
042 – 24-Hour Holdup* 066 – Momentary Keyswitch Arm
008 – Standard 24-Hour Fire
043 – 24-Hour Panic 067 – Maintained Keyswitch Arm
009 – Instant Stay/Away
045 – 24-Hour Heat 068 – Momentary Keyswitch Disarm
010 – Interior Delay
046 – 24-Hour Medical 069 – Maintained Keyswitch Disarm
011 – Day Zone
047 – 24-Hour Emergency 071 – Door Bell
012 – Night Zone
048 – 24-Hour Sprinkler* 072 – Push to Set
016 – Final Door Set
049 – 24-Hour Flood
017 – 24-Hour Burglary
[002] [001 - 248] Zone Attributes

Available Zone Attributes
See next page for defaults
1 – Bell Audible 5 – Force Arm 9 – Normally Close

13 – Zone 2-way Audio Activation
2 – Bell Steady 6 – Swinger Shutdown 10 – Single EOL
14 – Hold Up Verification
3 – Door Chime 7 – Transmission Delay 11 – Double EOL
15 - Triple EOL
4 – Bypass Enabled 8 – Burglary Verification 12 – Fast/Normal Loop Response
Zone Attribute Defaults (Description on page 82)
Zone Attributes
1 – Bell Audible 5 –Force Arm 9 – Normally Closed EOL
13 - Zone 2-way Audio Activation
2 – Bell Steady 6 – Swinger Shutdown 10 – Single EOL
14 - Hold Up Verification
3 – Chime Function 7 – Transmission Delay 11 – Double EOL
15 - Triple EOL
4 – Bypass Enabled 8 - Burglary Verification 12 – Fast/Normal Loop Response
- 160 -
Zone Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
000 Null Zone
001 Delay 1 ü ü ü ü ü CP-01

ü ü
002 Delay 2 ü ü ü ü ü CP-01

ü ü
003 Instant ü ü ü ü ü CP-01

ü ü
004 Interior ü ü ü ü CP-01

ü ü
005 Interior Stay/Away ü ü ü ü ü CP-01

ü ü
006 Delay Stay/Away ü ü ü ü ü CP-01

ü ü
007 Delayed 24-Hour Fire ü

008 Standard 24-Hour Fire ü
009 Instant Stay/Away ü ü ü ü CP-01

ü ü
010 Interior Delay ü ü ü ü CP-01

ü ü
011 Day Zone ü ü ü ü ü ü ü

012 Night Zone ü ü ü ü ü ü
016 Final Door Set ü ü ü ü CP-01

ü
CP-01
ü ü
017 24-Hour Burglary ü ü ü CP-01

ü
CP-01
ü ü
018 24-Hour Bell/Buzzer ü ü ü CP-01

ü
CP-01
ü ü
023 24-Hour Supervisory ü ü CP-01

ü
024 24-Hour Supervisory Buzzer ü ü CP-01

ü
CP-01
ü
025 Auto Verify Fire ü
027 Fire Supervisory
040 24-Hour Gas ü CP-01

ü
CP-01
ü
041 24-Hour CO ü
042 24-Hour Holdup ü ü CP-01

ü
CP-01
ü ü
043 24-Hour Panic ü ü CP-01

ü
CP-01
ü
045 24-Hour Heat ü CP-01

ü
046 24-Hour Medical ü ü CP-01

ü
CP-01
ü
047 24-Hour Emergency ü ü CP-01

ü
CP-01
ü
048 24-Hour Sprinkler ü ü CP-01

ü
CP-01
ü
049 24-Hour Flood ü ü CP-01

ü
CP-01
ü
051 24-Hour Latching Tamper ü ü CP-01

ü
CP-01
ü
052 24-Hour Non-Alarm ü
- 161 -
056 24 Hour High Temperature ü ü ü CP-01

ü
CP-01
ü
057 24 Hour Low Temperature ü ü ü CP-01

ü
CP-01
ü
060 24-Hr Non-Latching Tamper ü ü CP-01

ü
CP-01
ü
061 24-Hr Anti-Masking ü
066 Momentary Keyswitch Arm ü
067 Maintained Keyswitch Arm ü
068 Momentary Keyswitch Disarm ü
069 Maintained Keyswitch Disarm ü
071 Door Bell ü ü
072 Push to Set ü
6.3 End Of Line Resistance
[004] End of Line Resistance

Description Alarm (Default 5.6 kΩ)
001 – Single EOL
on page 84 Valid range: 0.5 kΩ to 28 kΩ (005 to 280)
Alarm (Default 5.6 kΩ)
002 – Double EOL
Valid range: 0.5 kΩ to 15 kΩ (005 -150)
Tamper (Default 5.6 kΩ)
Valid range: 0.5 kΩ to 15 kΩ (005 -150)
Alarm (Default 5.6 kΩ)
003 –Triple EOL
Valid range: 0.5 kΩ to 7.5 kΩ (005 -075)
Tamper (Default 5.6 kΩ)
Valid range: 0.5 kΩ to 7.5 kΩ (005 -075)
6.4 System Times
[005] System Times

000 – System Area Bell Cutoff (Default: 004 minutes):
Description
(3-Digit Decimal) Bell Delay Time (Default: 000 minutes):
on page 84
Burglary Verification Timer (Default: 060 minutes):
Holdup Verification Timer (Default: 008 hours):
Zone Loop Response Time (Default: 025 x 10 ms):
Automatic Clock Adjust (Default: 060 seconds):
001 – Partition 1 Timer Entry Delay 1 (Default: 030):
Entry Delay 2 (Default: 045):
Exit Delay (Default: 120):
Settle Delay (Default: 010):
002 – Partition 2 Timer Entry Delay 1:
See partition 1 for defaults Entry Delay 2:
- 162 -
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay:
Exit Delay:
Settle Delay
900 - Bell Delay Partition Mask 12345678
Default: All partitions on YYYYYYY
901 – Daylight Savings Begin Month (Default: 003):

Week (Default: 002):
Day (Default : 000):
Hour (Default: 002):
Increment (Default : 001):
902 – Daylight Savings End Month(Default: 011)
Week (Default: 001):
Day (Default: 000):
Hour (Default: 002):
Increment (Default : 001):
- 163 -
6.5 Access Codes
[006] Installer-Defined Codes

(4/6/8-Digit Decimal) 001 – Installer Code (Default:55555555)
(4/6/8-Digit Decimal) 002 – Master Code (Default:12345678)
(4/6/8-Digit Decimal) 003 – Maintenance Code (Default: AAAAAAAA)
(000-255) 005 – Code Version (Default:000)
6.6 PGM Programming
[007] [000 - 324] PGM Programming

1 2 3 4 5 6 7 8
[000] – Main Bell Partition Assignment
Y N N N N N N N
[001 – 324] PGM Partition Assignment

1 2 3 4 5 6 7 8
Default: Partition 1 on. All others off
Y N N N N N N N
[008] [000 - 324] PGM Timer Programming

[000] – PGM Timers Minutes or Seconds: o Minutes o Seconds
[001 – 324]: PGM 1 to 324

(3-Digit Decimal)
Valid Range: 001-255
Default: 005
Zone Follower by Zone Prox. Used Schedule
PGM
(000-248; Default 000) (000-095; Default 000) (000-004; Default 000)
Alarm Panel 001 PGM 1
002 PGM 2
003 PGM 3
004 PGM 4
005 PGM 5
HSM2204 #1
006 PGM 6
007 PGM 7
008 PGM 8
009 PGM 9
HSM2204 #2
010 PGM 10
011 PGM 11
012 PGM 12
013 PGM 13
HSM2204 #3
014 PGM 14
015 PGM 15
016 PGM 16
- 164 -

017 PGM 17
HSM2204 #4
018 PGM 18
019 PGM 19
020 PGM 20
037 PGM 37
HSM2208 #1
038 PGM 38
039 PGM 39
040 PGM 40
041 PGM 41
042 PGM 42
043 PGM 43
044 PGM 44
045 PGM 45
HSM2208 #2
046 PGM 46
047 PGM 47
048 PGM 48
049 PGM 49
050 PGM 50
051 PGM 51
052 PGM 52
053 PGM 53
HSM2208 #3
054 PGM 54
055 PGM 55
056 PGM 56
057 PGM 57
058 PGM 58
059 PGM 59
060 PGM 60
061 PGM 61
062 PGM 62
HSM2208 #4
063 PGM 63
064 PGM 64
065 PGM 65
066 PGM 66
067 PGM 67
068 PGM 68
069 PGM 69
070 PGM 70
HSM2208 #5
071 PGM 71
072 PGM 72
- 165 -

073 PGM 73
074 PGM 74
075 PGM 75
076 PGM 76
077 PGM 77
078 PGM 78
HSM2208 #6
079 PGM 79
080 PGM 80
081 PGM 81
082 PGM 82
083 PGM 83
084 PGM 84
085 PGM 85
086 PGM 86
HSM2208 #7
087 PGM 87
088 PGM 88
089 PGM 89
090 PGM 90
091 PGM 91
092 PGM 92
093 PGM 93
094 PGM 94
HSM2208 #8
095 PGM 95
096 PGM 96
097 PGM 97
098 PGM 98
099 PGM 99
100 PGM 100
101 PGM 101
HSM2208 #9
102 PGM 102
103 PGM 103
104 PGM 104
105 PGM 105
106 PGM 106
107 PGM 107
108 PGM 108
109 PGM 109
HSM2208 #10
110 PGM 110
111 PGM 111
112 PGM 112
113 PGM 113
- 166 -

114 PGM 114
115 PGM 115
116 PGM 116
117 PGM 117
HSM2208 #11
118 PGM 118
119 PGM 119
120 PGM 120
121 PGM 121
122 PGM 122
123 PGM 123
124 PGM 124
125 PGM 125
HSM2208 #12
126 PGM 126
127 PGM 127
128 PGM 128
129 PGM 129
130 PGM 130
131 PGM 131
132 PGM 132
133 PGM 133
HSM2208 #13
134 PGM 134
135 PGM 135
136 PGM 136
137 PGM 137
138 PGM 138
139 PGM 139
140 PGM 140
141 PGM 141
HSM2208 #14
142 PGM 142
143 PGM 143
144 PGM 144
145 PGM 145
146 PGM 146
147 PGM 147
148 PGM 148
149 PGM 149
HSM2208 #15
150 PGM 150
151 PGM 151
152 PGM 152
153 PGM 153
154 PGM 154
- 167 -

155 PGM 155
156 PGM 156
157 PGM 157
HSM2208 #16
158 PGM 158
159 PGM 159
160 PGM 160
161 PGM 161
162 PGM 162
163 PGM 163
164 PGM 164
293 PGM 293
HSM3204CX#17 294 PGM 294
295 PGM 295
296 PGM 296
297 PGM 297
298 PGM 298
299 PGM 299
300 PGM 300
301 PGM 301
302 PGM 302
303 PGM 303
304 PGM 304
305 PGM 305
306 PGM 306
307 PGM 307
308 PGM 308
309 PGM 309
310 PGM 310
311 PGM 311
312 PGM 312
313 PGM 313
314 PGM 314
315 PGM 315
316 PGM 316
317 PGM 317
318 PGM 318
319 PGM 319
320 PGM 320
321 PGM 321
322 PGM 322
323 PGM 323
324 PGM 324
- 168 -
[009] [001] - [164] PGM Types

121 – Command
100 – Null PGM 156 – Latched System Event 205 – Follower-Zones 33-40
Output 1
101 – Burg and Fire Bell 122 – Command
157 – System Tamper 206 – Follower-Zones 41-48
Follower Output 2
123 – Command
102 – Delayed Fire/ Burg 161 – DC Trouble 207 – Follower-Zones 49-56
Output 3
124 – Command
103 – Sensor Reset[*][7][2] 165 – Prox Used 208 – Follower-Zones 57-64
Output 4
129 – Partition Status
104 – 2-Wire Smoke 166 – Partition Prox Used 209 – Follower-Zones 65-72
Alarm Memory
175 – Bell Status and
107 - External Siren 132 – Holdup Output 210 – Follower-Zones 73-80
Programming Access Output
109 – Courtesy Pulse 134 – 24Hr Silent 176 – Remote Operation 211 – Follower-Zones 81-88
135 – 24Hr Audible
111 – Keypad Buzzer Follow 184 – Open After Alarm 212 – Follower-Zones 89-96
Input
114 – Ready To Arm 146 – TLM and Alarm 200 – Zone Follower 213 – Follower-Zones 97-104
115 – System Armed Status 147 – Kissoff 201 – Follower-Zones 1-8 214 – Follower-Zones 105-112
116 – Away Armed Status 148 – Ground Start 202 – Follower-Zones 9-16 215 – Follower-Zones 113-120
149 – Alt.
117 – Stay Armed Status 203 – Follower-Zones 17-24 216 – Follower-Zones 120-128
Communicator
120 – Away Armed/no Bypass
155 – System Trouble 204 – Follower-Zones 25-32
Status
(3-Digit Decimal)
Valid Range: 001-216
001 Default: 121 Command Output 1
002 Default: 156 System Event
003 - 324 Default: 101 Burg and Fire Bell Follower
Prox. Used Schedule
Zone Follower by Zone
PGM (000-095; (000-004;
(000-248; Default 000)
Default 000) Default 000)
002 PGM 2
003 PGM 3
004 PGM 4
005 PGM 5
HSM2204 #1
006 PGM 6
007 PGM 7
008 PGM 8
009 PGM 9
HSM2204 #2
010 PGM 10
011 PGM 11
012 PGM 12
- 169 -
[009] [001] - [164] PGM Types

013 PGM 13
HSM2204 #3
014 PGM 14
015 PGM 15
016 PGM 16
017 PGM 17
HSM2204 #4
018 PGM 18
019 PGM 19
020 PGM 20
037 PGM 37
HSM2208 #1
038 PGM 38
039 PGM 39
040 PGM 40
041 PGM 41
042 PGM 42
043 PGM 43
044 PGM 44
045 PGM 45
HSM2208 #2
046 PGM 46
047 PGM 47
048 PGM 48
049 PGM 49
050 PGM 50
051 PGM 51
052 PGM 52
053 PGM 53
HSM2208 #3
054 PGM 54
055 PGM 55
056 PGM 56
057 PGM 57
058 PGM 58
059 PGM 59
060 PGM 60
061 PGM 61
062 PGM 62
HSM2208 #4
063 PGM 63
064 PGM 64
065 PGM 65
066 PGM 66
067 PGM 67
068 PGM 68
- 170 -
[009] [001] - [164] PGM Types

069 PGM 69
070 PGM 70
HSM2208 #5
071 PGM 71
072 PGM 72
073 PGM 73
074 PGM 74
075 PGM 75
076 PGM 76
077 PGM 77
078 PGM 78
HSM2208 #6
079 PGM 79
080 PGM 80
081 PGM 81
082 PGM 82
083 PGM 83
084 PGM 84
085 PGM 85
086 PGM 86
HSM2208 #7
087 PGM 87
088 PGM 88
089 PGM 89
090 PGM 90
091 PGM 91
092 PGM 92
093 PGM 93
094 PGM 94
HSM2208 #8
095 PGM 95
096 PGM 96
097 PGM 97
098 PGM 98
099 PGM 99
100 PGM 100
101 PGM 101
HSM2208 #9
102 PGM 102
103 PGM 103
104 PGM 104
105 PGM 105
106 PGM 106
107 PGM 107
108 PGM 108
- 171 -
[009] [001] - [164] PGM Types

109 PGM 109
HSM2208 #10
110 PGM 110
111 PGM 111
112 PGM 112
113 PGM 113
114 PGM 114
115 PGM 115
116 PGM 116
117 PGM 117
HSM2208 #11
118 PGM 118
119 PGM 119
120 PGM 120
121 PGM 121
122 PGM 122
123 PGM 123
124 PGM 124
125 PGM 125
HSM2208 #12
126 PGM 126
127 PGM 127
128 PGM 128
129 PGM 129
130 PGM 130
131 PGM 131
132 PGM 132
133 PGM 133
HSM2208 #13
134 PGM 134
135 PGM 135
136 PGM 136
137 PGM 137
138 PGM 138
139 PGM 139
140 PGM 140
141 PGM 141
HSM2208 #14
142 PGM 142
143 PGM 143
144 PGM 144
145 PGM 145
146 PGM 146
147 PGM 147
148 PGM 148
- 172 -
[009] [001] - [164] PGM Types

149 PGM 149
HSM2208 #15
150 PGM 150
151 PGM 151
152 PGM 152
153 PGM 153
154 PGM 154
155 PGM 155
156 PGM 156
157 PGM 157
HSM2208 #16
158 PGM 158
159 PGM 159
160 PGM 160
161 PGM 161
162 PGM 162
163 PGM 163
164 PGM 164
293 PGM 293
HSM3204CX#17 294 PGM 294
295 PGM 295
296 PGM 296
297 PGM 297
298 PGM 298
299 PGM 299
300 PGM 300
301 PGM 301
302 PGM 302
303 PGM 303
304 PGM 304
305 PGM 305
306 PGM 306
307 PGM 307
308 PGM 308
309 PGM 309
310 PGM 310
311 PGM 311
312 PGM 312
313 PGM 313
314 PGM 314
315 PGM 315
316 PGM 316
317 PGM 317
- 173 -
[009] [001] - [164] PGM Types

318 PGM 318
319 PGM 319
320 PGM 320
321 PGM 321
322 PGM 322
323 PGM 323
324 PGM 324
[010] [000 - 164] PGM Attributes

R 01 – Fire Alarm
[000] – Main R 02 – CO Alarm
Bell Mask
R 03 – Burglary Alarm
Description on
R 04 – Flood Alarm
page 92
R 05 – Bell Squawks
001-164 PGM Attributes
PGM 1-164: 100 – Null PGM
101 – Fire and Burglary R 01 – True Output
102 – Delay Fire and Burg R 01 – True Output
103 – Sensor Reset [*][7][2] o 03 – Code Required
107 - External Siren R 01 – True Output
109 – Courtesy Pulse R 01 – True Output
R 01 – True Output
o 02 – Timed Output
R 09 – Entry Delay
R 10 – Exit Delay
R 11 – Door Chime
R 12 – Keypad Buzzer Zone
R 13 – Audible Exit Zone
R 14 – Auto-Arm Pre-Alert
114 – Ready To Arm R 01 – True Output
115 – Armed Status R 01 – True Output
116 – Armed Away Mode R 01 – True Output
117 – Armed Stay Mode R 01 – True Output
120 – Away Armed No Bypass R 01 – True Output
121 – Command Output 1 o 02 – Timed Output R Schedule 001
R 03 – Code Required
o 03 – Code Required
- 174 -

129 – Partition Status Alarm Memory R 01 – True Output
146 – TLM And Alarm R 01 – True Output
147 – Kissoff Output R 01 – True Output
148 – Ground Start R 01 – True Output
R 02 – Timed Output
o 04 – Fire Alarm
o 05 – Panic Alarm
o 06 – Burglary Alarm
o 07 – Open/Close
149 – Alternate Communicator o 08 – Zone Auto Bypass
o 09 – Medical Alarm
o 10 – Burglary Verified
o 11 – Open After Alarm
o 12 – Emergency Alarm
o 13 – Duress Alarm
o 14 – Holdup Verified
R 04 – Service Required
R 05 – Loss of Clock
R 06 – DC Trouble
R 07 – Bus Voltage
R 08 – AC Trouble
155 – System Trouble R 09 – Device Fault
R 10 – Device Battery
R 11 – Device Tamper
R 12 – RF Delinquency
R 13 – Module Supervisory
R 14 – Module Tamper
R 15 – Communications
R 16 – Not Networked
- 175 -

R 04 – Fire Alarm
R 05 – Panic Alarm
R 06 – Burglary Alarm
R 07 – Medical Alarm
R 08 – Supervisory
156 – Latched System Event
R 09 – Priority Event
R 10 – Holdup
R 11 – Duress Alarm
R 12 – Emergency Alarm
R 13 – Fire Supervisory
R 14 – Fire Trouble
R 15 – CO Alarm
R 10 – Zone Tampers
161 – DC Trouble
R 09 – Battery Low
R 10 – Battery Absent
165 – Prox Used R 01 – True Output
166 – Prox Used Part
175 – Bell Prog Access R 01 – True Output
R 02 – Timed Output
200 – Zone Follow by Zone
R 04 – Latching
o 05 – Follow Alarm
- 176 -

201 Zone Follower Zones 1-8
213 Zone Follower Zones 97-104 R 04 – Latching
214 Zone Follower Zones 105-112 o 05 – Follow Alarm
215 Zone Follower Zones 113-120 R 09 – Zone Terminal 1

R 12 – Zone Terminal 4
[010] PGM Attribute Assignment:

(16-Bit Toggles)

PGM
002 PGM 2
003 PGM 3
- 177 -

(16-Bit Toggles)

PGM
004 PGM 4
005 PGM 5
HSM2204 #1
006 PGM 6
007 PGM 7
008 PGM 8
009 PGM 9
HSM2204 #2
010 PGM 10
011 PGM 11
012 PGM 12
013 PGM 13
HSM2204 #3
014 PGM 14
015 PGM 15
016 PGM 16
017 PGM 17
HSM2204 #4
018 PGM 18
019 PGM 19
020 PGM 20
037 PGM 37
HSM2208 #1
038 PGM 38
039 PGM 39
040 PGM 40
041 PGM 41
042 PGM 42
043 PGM 43
044 PGM 44
045 PGM 45
HSM2208 #2
046 PGM 46
047 PGM 47
048 PGM 48
049 PGM 49
050 PGM 50
051 PGM 51
052 PGM 52
053 PGM 53
HSM2208 #3
054 PGM 54
055 PGM 55
056 PGM 56
- 178 -

(16-Bit Toggles)

PGM
057 PGM 57
058 PGM 58
059 PGM 59
060 PGM 60
061 PGM 61
062 PGM 62
HSM2208 #4
063 PGM 63
064 PGM 64
065 PGM 65
066 PGM 66
067 PGM 67
068 PGM 68
069 PGM 69
070 PGM 70
HSM2208 #5
071 PGM 71
072 PGM 72
073 PGM 73
074 PGM 74
075 PGM 75
076 PGM 76
077 PGM 77
078 PGM 78
HSM2208 #6
079 PGM 79
080 PGM 80
081 PGM 81
082 PGM 82
083 PGM 83
084 PGM 84
085 PGM 85
086 PGM 86
HSM2208 #7
087 PGM 87
088 PGM 88
089 PGM 89
090 PGM 90
091 PGM 91
092 PGM 92
- 179 -

(16-Bit Toggles)

PGM
093 PGM 93
094 PGM 94
HSM2208 #8
095 PGM 95
096 PGM 96
097 PGM 97
098 PGM 98
099 PGM 99
100 PGM 100
101 PGM 101
HSM2208 #9
102 PGM 102
103 PGM 103
104 PGM 104
105 PGM 105
106 PGM 106
107 PGM 107
108 PGM 108
109 PGM 109
HSM2208 #10
110 PGM 110
111 PGM 111
112 PGM 112
113 PGM 113
114 PGM 114
115 PGM 115
116 PGM 116
117 PGM 117
HSM2208 #11
118 PGM 118
119 PGM 119
120 PGM 120
121 PGM 121
122 PGM 122
123 PGM 123
124 PGM 124
125 PGM 125
HSM2208 #12
126 PGM 126
127 PGM 127
128 PGM 128
129 PGM 129
- 180 -

(16-Bit Toggles)

PGM
130 PGM 130
131 PGM 131
132 PGM 132
133 PGM 133
HSM2208 #13
134 PGM 134
135 PGM 135
136 PGM 136
137 PGM 137
138 PGM 138
139 PGM 139
140 PGM 140
141 PGM 141
HSM2208 #14
142 PGM 142
143 PGM 143
144 PGM 144
145 PGM 145
146 PGM 146
147 PGM 147
148 PGM 148
149 PGM 149
HSM2208 #15
150 PGM 150
151 PGM 151
152 PGM 152
153 PGM 153
154 PGM 154
155 PGM 155
156 PGM 156
157 PGM 157
HSM2208 #16
158 PGM 158
159 PGM 159
160 PGM 160
161 PGM 161
162 PGM 162
163 PGM 163
164 PGM 164
293 PGM 293
HSM3204CX#17 294 PGM 294
- 181 -

(16-Bit Toggles)

PGM
295 PGM 295
296 PGM 296
297 PGM 297
298 PGM 298
299 PGM 299
300 PGM 300
301 PGM 301
302 PGM 302
303 PGM 303
304 PGM 304
305 PGM 305
306 PGM 306
307 PGM 307
308 PGM 308
309 PGM 309
310 PGM 310
311 PGM 311
312 PGM 312
313 PGM 313
314 PGM 314
315 PGM 315
316 PGM 316
317 PGM 317
318 PGM 318
319 PGM 319
320 PGM 320
321 PGM 321
322 PGM 322
323 PGM 323
324 PGM 324
[011] PGM Config. Options


PGM
002 PGM 2
- 182 -


PGM
003 PGM 3
004 PGM 4
005 PGM 5
HSM2204 #1
006 PGM 6
007 PGM 7
008 PGM 8
009 PGM 9
HSM2204 #2
010 PGM 10
011 PGM 11
012 PGM 12
013 PGM 13
HSM2204 #3
014 PGM 14
015 PGM 15
016 PGM 16
017 PGM 17
HSM2204 #4
018 PGM 18
019 PGM 19
020 PGM 20
037 PGM 37
HSM2208 #1
038 PGM 38
039 PGM 39
040 PGM 40
041 PGM 41
042 PGM 42
043 PGM 43
044 PGM 44
045 PGM 45
HSM2208 #2
046 PGM 46
047 PGM 47
048 PGM 48
049 PGM 49
050 PGM 50
051 PGM 51
052 PGM 52
053 PGM 53
HSM2208 #3
054 PGM 54
055 PGM 55
056 PGM 56
- 183 -


PGM
057 PGM 57
058 PGM 58
059 PGM 59
060 PGM 60
061 PGM 61
062 PGM 62
HSM2208 #4
063 PGM 63
064 PGM 64
065 PGM 65
066 PGM 66
067 PGM 67
068 PGM 68
069 PGM 69
070 PGM 70
HSM2208 #5
071 PGM 71
072 PGM 72
073 PGM 73
074 PGM 74
075 PGM 75
076 PGM 76
077 PGM 77
078 PGM 78
HSM2208 #6
079 PGM 79
080 PGM 80
081 PGM 81
082 PGM 82
083 PGM 83
084 PGM 84
085 PGM 85
086 PGM 86
HSM2208 #7
087 PGM 87
088 PGM 88
089 PGM 89
090 PGM 90
091 PGM 91
092 PGM 92
- 184 -


PGM
093 PGM 93
094 PGM 94
HSM2208 #8
095 PGM 95
096 PGM 96
097 PGM 97
098 PGM 98
099 PGM 99
100 PGM 100
101 PGM 101
HSM2208 #9
102 PGM 102
103 PGM 103
104 PGM 104
105 PGM 105
106 PGM 106
107 PGM 107
108 PGM 108
109 PGM 109
HSM2208 #10
110 PGM 110
111 PGM 111
112 PGM 112
113 PGM 113
114 PGM 114
115 PGM 115
116 PGM 116
117 PGM 117
HSM2208 #11
118 PGM 118
119 PGM 119
120 PGM 120
121 PGM 121
122 PGM 122
123 PGM 123
124 PGM 124
125 PGM 125
HSM2208 #12
126 PGM 126
127 PGM 127
128 PGM 128
129 PGM 129
130 PGM 130
- 185 -


PGM
131 PGM 131
132 PGM 132
133 PGM 133
HSM2208 #13
134 PGM 134
135 PGM 135
136 PGM 136
137 PGM 137
138 PGM 138
139 PGM 139
140 PGM 140
141 PGM 141
HSM2208 #14
142 PGM 142
143 PGM 143
144 PGM 144
145 PGM 145
146 PGM 146
147 PGM 147
148 PGM 148
149 PGM 149
HSM2208 #15
150 PGM 150
151 PGM 151
152 PGM 152
153 PGM 153
154 PGM 154
155 PGM 155
156 PGM 156
157 PGM 157
HSM2208 #16
158 PGM 158
159 PGM 159
160 PGM 160
161 PGM 161
162 PGM 162
163 PGM 163
164 PGM 164
293 PGM 293
HSM3204CX#17 294 PGM 294
295 PGM 295
296 PGM 296
- 186 -


PGM
297 PGM 297
298 PGM 298
299 PGM 299
300 PGM 300
301 PGM 301
302 PGM 302
303 PGM 303
304 PGM 304
305 PGM 305
306 PGM 306
307 PGM 307
308 PGM 308
309 PGM 309
310 PGM 310
311 PGM 311
312 PGM 312
313 PGM 313
314 PGM 314
315 PGM 315
316 PGM 316
317 PGM 317
318 PGM 318
319 PGM 319
320 PGM 320
321 PGM 321
322 PGM 322
323 PGM 323
324 PGM 324
6.7 System Lockout

[012] System Lockout
(3-Digit Decimal)
(Range: 000-255; Default 000 )
Keypad Lockout: EN
Note: For installations maximum programmed lockout of 10
attempts.
- 187 -
(Range: 001-255; Default 000 )

Keypad Lockout Duration:
EN
Note: For installations minimum programmed duration of 2 minutes.
Remote Lockout: (Range: 003-255; Default 006)
Remote Lockout Duration: (Range: 001-255; Default 060)
6.8 System Options
[013] System Options 1

o 1 – NC Loop/EOL
o 2 – DEOL/SEOL
EN R 2 – DEOL/SEOL
R 3 – Show All Troubles When Armed

o 4 – Tamper/Faults Open Zone
R5 – Auto-Arm Schedule in [*][6]
R 6 – Audible Exit Fault
R 7 – Event Buffer Follows Swinger
o 8 – Temporal Three Fire Signaling

o 1 – Bell Squawk
o 2 – Bell Squawk on Auto-Arm
o 3 – Bell Squawk on Exit
o 4 – Bell Squawk on Entry
o 5 – Bell Squawk on Trouble
o 6 – Reserved
o 7 – Exit Delay Termination
o 8 – Fire Bell Continues

R1 – [F] Key Enabled
o 2 – [P] Key Annunciation
o 3 – Quick Exit
R 4 – Quick Arming/Function Key
o 5 – Reserved
o 6 – Master Code Not User Changeable
R 7 – Telephone Line Monitor Enable
R 8 – TLM Audible When Armed

R 1 – AC Trouble Display
- 188 -
o 2 – AC Trouble Light Flashes
EN R 2 – AC Trouble Light Flashes
o 3 – Keypad Blanking
EN R 3 – Keypad Blanking
o 4 – Keypad Blanking Requires Code
EN R 4 – Keypad Blanking Requires Code
R 5 – Keypad Backlighting
o6 – Power Save Mode
o 7 – Bypass Display When Armed
o8 – Keypad Tampers Enabled
EN R 8 – Keypad Tampers Enabled

R 1 – Chime on Opening
o 2 – Chime on Closing
EN R 2 – Chime on Closing
o3 – Audible RF Jam Trouble Beeps

o 4 – Multi-Hit
o 5 – Late to Close
o 6 – Daylight Savings Time
o7 – Silence Chime During Quick Exit Delay
o 8 – Bell Squawk on Away Arm/Disarm

o 1 – Test Transmission Exception
o 2 – Real-Time Bypass Reporting
o 3 – Report Bypass for Stay Away Zones
o 4 – Auto Bypass Report
o 5 – Keypad Buzzer Alarm
o 6 – Reserved
o 7 – Exit Delay Restart
CP-01 R 7 – Exit Delay Restart
R 7 – Exit Delay Restart

o 8 – AC Fail Trouble Beeps
EN R 8 – AC Fail Trouble Beeps

o 1 – Audible Wireless Zone Fault
- 189 -
o 2 – Latching Troubles
EN R 2 – Latching Troubles
o3 – Reserved
o 4 – Reserved
o 5 – Audible Bus Fault
o 6 – Duress Code
R7 – Temperature in Celsius
o 8 – Reset After Zone Activation

o 1 – Access Code Entry During Entry Delay
o 2 – EU Entry Procedure
EN R 2 – EU Entry Procedure
o 3 – [*][8] Access While Armed

o 4 – Remote Reset
o 5 – Engineer's Reset
o 6 – Keyswitch Disarming During Entry Delay
o 7 – Installer Access and DLS
EN R 7 – Installer Access and DLS
o 8 – Troubles Inhibits Arming
EN R 8 – Troubles Inhibits Arming

EN o 1 – Trouble Display
EN o 2 – Keypad Blanking While Armed
o 3 – Reserved
o 4 – Ready Display
o 5 – PGM Keypad Blanking
EN R 5 – PGM Keypad Blanking
o 6 – Armed Display
o 7 – Open Cancels Arming
EN R 7 – Open Cancels Arming
o 8 – Audible Exit Delay for Stay Arm

o 1 – [F] Key Option
o 2 – Reserved
- 190 -
o 3 – Reserved
UL EN o 4 – Test Transmission Counter in Hours
o 5 – Away to Stay Toggle

o 6 – 2- Way Audio Disconnect
o 7 – Trouble Beeps Are Silent
o 8 – Keyswitch Arms in Away Mode
R 8 – Keyswitch Arms in Away Mode

o 1 – Ready LED Flash for Force Arm
o 2 – Access Code Required for [*][*]
o 3 – Tamper/Fault Detection
o 4 – Access Code Required for [*][1]
EN UL R 4 – Access Code Required for [*][1]

Note: For UL installations, this setting must be enabled.
EN R 5 – Access Code Required for [*][2]
o 8 – [*][6] Accessibility Option

o 1– Reserved
o 2 – Reserved
o 3 – AC/DC Inhibits Arming
EN R 3 – AC/DC Inhibits Arming
EN o 4 – Tampers Inhibit Arming
o 5 – Real Time Clock Option

o 6 – Reserved
o 7 – Reserved
o 8 – DLS Disconnect

o 1 – European Dial
UL R 2 – Force Dial
- 191 -
o 3 – Test Transmission Counter in Minutes
EN o 4 – Warm Start Indication
o5 – ID Tone
o 6 – Tone Generated-2100Hz
o 7 – DLS Window
o 8 – FTC Audible Bell
[040] User Authentication

R 1 – User Code or Prox. Tag
o 2 – User Code and Prox. Tag
[041] Access Code Digits

R 00 – 4-Digit Access Codes
EN o 01 – 6-Digit Access Codes
[042] Event Verification

01 – Burglary Verified Counter (Default: 002):
02 – Holdup Counter (Default: 002):
001 – Police Code (Default)
03 – Burglary Verification Selection: 002 – Cross Zoning
003 – Sequential Detection
6.9 Auto-Arm_Disarm
[151] Partition 1 Auto-Arm/Disarm

001 – Partition 1 Auto-Arming Times: 24-Hour:
(4-digit HH:MM) Sunday: Thursday:
Default: 9999 Monday: Friday:
Tuesday: Saturday:
Wednesday:
002 – Partition 1 Auto-Disarm Times: 24-Hour:
Tuesday: Saturday:
Wednesday:
003 – Partition 1 Auto-Disarming Holiday Schedule: Holiday 1: o On R Off
(3-digit decimal) Holiday 2: o On R Off
Holiday 3: o On R Off
004 – Partition 1 Auto-Arming Pre-Alert (Default: 004):
- 192 -
005 – Partition 1 Auto-Arming Postpone Timer (Default: 000):

006 – Partition 1 No Activity Arming Timer (Default: 000):
007 – Partition 1 No Activity Arming Pre-Alert Timer (Default: 001):

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:
- 193 -

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:

- 194 -

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:

Tuesday: Saturday:
Wednesday:
Tuesday: Saturday:
Wednesday:

Tuesday: Saturday:
Wednesday:
- 195 -

Tuesday: Saturday:
Wednesday:
[200] Partition Mask

001 – Partition 1 to 8
R – Partition 1
Enable Mask
o – Partition 2
Descriptions on page 114 o – Partition 3
o – Partition 4
o – Partition 5
o – Partition 6
o – Partition 7
o – Partition 8
6.10 Partition and Zone Assignment
[201]-[208] Partition Zone Assignment

(Description on page 115)
[201] Partition 1 Zone Assignment [202] Partition 2 Zone Assignment
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
001 – 01-08 R R R R R R R R 001 – 01-08 o o o o o o o o
002 – 09-16 R R R R R R R R 002 – 09-16 o o o o o o o o
003 – 17-24 o o o o o o o o 003 – 17-24 o o o o o o o o
- 196 -

018 - 137-144 o o o o o o o o 018 - 137-144 o o o o o o o o
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
- 197 -

Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
- 198 -

Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
6.11 Communications
[300] Panel/Receiver Communications Path

001 – Receiver 1: R PSTN-Phone Line
o Alt Comm Auto Routing
o Alt Comm Receiver 1 - Ethernet
o Alt Comm Receiver 3 - Cellular
oAlt Comm Receiver 4 - Cellular
- 199 -

oAlt Comm Receiver 2 - Ethernet
oAlt Comm Receiver 4 - Cellular
o Alt Comm Receiver 4 - Cellular 2
[301] Phone Number Programming

(Default: DFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF)
(32-Digit HEX) 001 – Receiver 1 Phone Number Programming:
Description on page 116 002 – Receiver 2 Phone Number Programming:
003 – Receiver 3 Phone Number Programming:
004 – Receiver 4 Phone Number Programming:
[304] Call Waiting Cancel String
Call Waiting Cancel String (6-digit Hex; Default: DB70EF CP-01
Default: FFFFFF):
[307] Zone Reporting

Description on page 116 (001-248 = zones 1-248)
R 1 – Alarm
R 2 – Alarm Restore
R 3 – Tamper
R 4 – Tamper Restore
R 5 – Fault
R 6 – Fault Restore
RRRRRRoo RRRRRRoo RRRRRRoo RRRRRRoo RRRRRRoo
001 002 003 004 005
12345678 12345678 12345678 12345678 12345678
006 007 008 009 010
12345678 12345678 12345678 12345678 12345678
011 012 013 014 015
12345678 12345678 12345678 12345678 12345678
016 017 018 019 020
12345678 12345678 12345678 12345678 12345678
- 200 -

021 022 023 024 025
12345678 12345678 12345678 12345678 12345678
026 027 028 029 030
12345678 12345678 12345678 12345678 12345678
031 032 033 034 035
12345678 12345678 12345678 12345678 12345678
036 037 038 039 040
12345678 12345678 12345678 12345678 12345678
041 042 043 044 045
12345678 12345678 12345678 12345678 12345678
046 047 048 049 050
12345678 12345678 12345678 12345678 12345678
051 052 053 054 055
12345678 12345678 12345678 12345678 12345678
056 057 058 059 060
12345678 12345678 12345678 12345678 12345678
061 062 063 064 065
12345678 12345678 12345678 12345678 12345678
066 067 068 069 070
12345678 12345678 12345678 12345678 12345678
071 072 073 074 075
12345678 12345678 12345678 12345678 12345678
076 077 078 079 080
12345678 12345678 12345678 12345678 12345678
081 082 083 084 085
12345678 12345678 12345678 12345678 12345678
086 087 088 089 090
12345678 12345678 12345678 12345678 12345678
091 092 093 094 095
12345678 12345678 12345678 12345678 12345678
096 097 098 099 100
12345678 12345678 12345678 12345678 12345678
101 102 103 104 105
12345678 12345678 12345678 12345678 12345678
106 107 108 109 110
12345678 12345678 12345678 12345678 12345678
111 112 113 114 115
12345678 12345678 12345678 12345678 12345678
116 117 118 119 120
12345678 12345678 12345678 12345678 12345678
121 122 123 124 125
12345678 12345678 12345678 12345678 12345678
126 127 128 129 130
12345678 12345678 12345678 12345678 12345678
- 201 -

131 132 133 134 135
12345678 12345678 12345678 12345678 12345678
136 137 138 139 140
12345678 12345678 12345678 12345678 12345678
141 142 143 144 145
12345678 12345678 12345678 12345678 12345678
146 147 148 149 150
12345678 12345678 12345678 12345678 12345678
151 152 153 154 155
12345678 12345678 12345678 12345678 12345678
156 157 158 159 160
12345678 12345678 12345678 12345678 12345678
161 162 163 164 165
12345678 12345678 12345678 12345678 12345678
166 167 168 169 170
12345678 12345678 12345678 12345678 12345678
171 172 173 174 175
12345678 12345678 12345678 12345678 12345678
176 177 178 179 180
12345678 12345678 12345678 12345678 12345678
181 182 183 184 185
12345678 12345678 12345678 12345678 12345678
186 187 188 189 190
12345678 12345678 12345678 12345678 12345678
191 192 193 194 195
12345678 12345678 12345678 12345678 12345678
196 197 198 199 120
12345678 12345678 12345678 12345678 12345678
121 122 123 124 200
12345678 12345678 12345678 12345678 12345678
201 202 203 204 205
12345678 12345678 12345678 12345678 12345678
206 207 208 209 210
12345678 12345678 12345678 12345678 12345678
211 212 213 214 215
12345678 12345678 12345678 12345678 12345678
216 217 218 219 220
12345678 12345678 12345678 12345678 12345678
221 222 223 224 225
12345678 12345678 12345678 12345678 12345678
226 227 228 229 230
12345678 12345678 12345678 12345678 12345678
231 232 233 234 235
12345678 12345678 12345678 12345678 12345678
- 202 -

236 237 238 239 240
12345678 12345678 12345678 12345678 12345678
241 242 243 244 245
12345678 12345678 12345678 12345678 12345678
RRRRRRoo RRRRRRoo RRRRRRoo
246 247 248
12345678 12345678 12345678

R1 – Duress Alarm
R 2 – Opening After Alarm
R 3 – Recent Closing Alarm
R 4 – Zone Expander Supervisory Alarm
001 – Miscellaneous Alarm 1
R 5 – Zone Expander Supervisory Alarm Restore
R6 – Burglary Verified
R 7 – Burglary Not Verified Alarm
R 8 – Alarm Cancel
002 – Miscellaneous Alarm 2 R 1 – Holdup Verified Alarm
R 1 – Keypad Fire Alarm-F Key
R 2 – Keypad Fire Restore
R 3 – Keypad Medical Alarm-M Key
R 4 – Keypad Medical Restore
011 – Priority Alarms 1
R 5 – Keypad Panic Alarm-P Key Alarm
R 6 – Keypad Panic Restore
R 7 – Auxiliary Input Alarm
R 8 – Auxiliary Input Alarm Restore
R 3 – PGM 2 2-Wire Alarm
021 – Fire Alarms 1
R 4 – PGM 2 2-Wire Alarm Restore
R 4 – Module Tamper Restore
101 – Tamper Events
R5 – Keypad Lockout
R 7 – Remote Lockout
R 1 – User Closing
R 2 – User Opening
R 5 – Special Closing
201 – Open/Close Events 1
R 6 – Special Opening
R 7 – Keyswitch Opening
R 8 – Keyswitch Closing
R 1 – Automatic Closing
202 – Open/Close Events 2 R 2 – Automatic Disarm
R 3 – Auto Arm Cancellation/Postpone
R 1 – Late to Close
211 – Miscellaneous Open/Close
R 2 – Late to Open
Events
R 5 – Exit Fault
- 203 -

R 1 – Zone Bypass
221 – Bypass Events R 2 – Zone Unbypass
R 3 – Partial Closing
R1 – Panel AC Fail Trouble
R2 – Panel AC Fail Restore
R 3 – Panel Low Battery Trouble
R 4 – Panel Low Battery Trouble Restore
301 – Panel Events 1
R 5 – Panel Battery Absent Trouble
R 6 – Panel Battery Absent Trouble Restore
R 7– Panel Power Unit Failure
R 8 – Panel Power Unit Fail Restore
R 1 – Bell Circuit Trouble
R 2 – Bell Circuit Trouble Restore
R 3 – Telephone Line Trouble
R 4 – Telephone Line Trouble Restore
R 5 – Auxiliary Trouble
R 6 – Auxiliary Trouble Restore
R 7– Overcurrent Trouble
R 8 – Overcurrent Trouble Restore
R 3 – PGM 2 2-Wire Trouble
R 4 – PGM 2 2-Wire Trouble Restore
R 1 – RF Jam Trouble
R 2 – RF Jam Trouble Restore
R 3 – Fire Trouble
R 4 – Fire Trouble Restore
311 – Maintenance Events 1
R 5 – Cold Start
R 6 – Delinquency
R 7 – Self Test Trouble
R 8 – Self Test Trouble Restore
- 204 -

NA
o 1 – Installer Lead IN
o 2 – Installer Lead OUT
o 3 – DLS Lead IN
o 4 – DLS Lead OUT
o 5 – SA Lead IN
o 6 – SA Lead OUT
o 7 – Event Buffer 75% Full
312 – Maintenance Events 2
EN
o 1 – Installer Lead IN
o 2 – Installer Lead OUT
o 3 – DLS Lead IN
o 4 – DLS Lead OUT
o 5 – SA Lead IN
R 6 – SA Lead OUT
R 7 – Event Buffer 75% Full
R 1 – Firmware Update Begin
313 – Maintenance Events 3 R 2 – Firmware Update Successful
R 3 – Firmware Update Fail
R 1 – Gas Trouble
R 2 – Gas Trouble Restore
R 3 – Heat Trouble
314 – Maintenance Events 4 R 4 – Heat Trouble Restore
R 5 – Freeze Trouble
R 6 – Freeze Trouble Restore
R 7 – Probe Disconnected Trouble
R 8 – Probe Disconnected Restore
R2 – Receiver 1 FTC Restore
321 – Receiver Events
R1 – Module AC Trouble
R2 – Module AC Trouble Restore
R 3 – Module Battery Trouble
R 4 – Module Battery Trouble Restore
331 – Module Events 1
R 5 – Module Battery Absent
R 6 – Module Battery Absent Restore
R 7 – Module Power Unit Fail
R 8 – Module Power Unit Fail Restore
- 205 -

R 1 – Module Low Voltage Trouble
R 2 – Module Low Voltage Restore
R 3 – Module Supervisory
R 4 – Module Supervisory Restore
R 5 – Module Aux Trouble
R 6 – Module Aux Trouble Restore
R 1 – Output 1 Fault
R 2 – Output 1 Fault Restore
R 1 – Alt. Comm. Module Comm Fault
351 – Alternate R 2 – Alt. Comm. Module Comm Fault Restore
Communicator 1 R 7 – Alt. Comm. Radio/SIM Failure
R8 – Alt. Comm. Radio/SIM Failure Restore
R 1 – Alt. Comm. Network Fault
352 – Alternate R 2 – Alt. Comm. Network Fault Restore
Communicator 2 R 5 – Alt. Comm. Ethernet Trouble
R 6 – Alt. Comm. Ethernet Trouble Restore
R 1 – Alt. Comm Receiver 1 Trouble
R 2 – Alt. Comm Receiver 1 Restore
354 – Alternate R 4 – Alt. Comm Receiver 2 Restore
Communicator 4 R 5 – Alt. Comm Receiver 3 Trouble
R 1 – Alt. Comm Receiver 1 Supervision Failure
R 2 – Alt. Comm Receiver 1 Supervision Restore
355 – Alternate Communicator 5
R1 – Device AC Fail
R2 – Device AC Restore
361 – Wireless Device Events R 3 – Device Low Battery
R 4 – Device Low Battery Restore
R 5 – Device Fault
R 6 – Device Fault Restore
R 1 – Walk Test Start
R 2 – Walk Test End
401 – System Test Events R 3 – Periodic Test Transmission
R 4 – Periodic Test Transmission with Trouble
R 5 – System Test
- 206 -
6.12 Call Directions
[309] System Call Direction

001 – Maintenance Events: R Receiver #1 RReceiver #3
RReceiver #2 RReceiver #4
002 – Test Transmission Events: RReceiver #1 R Receiver #3
RReceiver #2 R Receiver #4
[310] Account Codes

(4-Digit HEX; Default FFFF)
000 – System Account Code (6-digit Hex; Default: FFFFFF):
001 – Partition 1 Account Code:
[311] Partition 1 Call Directions

001 – Partition 1 Alarm/ Restore: R Receiver #1 RReceiver #3
R Receiver #2 RReceiver #4
002 – Partition 1 Tamper/ Restore: R Receiver #1 R Receiver #3
R Receiver #2 R Receiver #4
003 – Partition 1 Opening/ Closing: oReceiver #1 o Receiver #3
o Receiver #2 o Receiver #4

001 – Partition 2 Alarm/ Restore: R Receiver #1 R Receiver #3
003 – Partition 2 Opening/ Closing: o Receiver #1 o Receiver #3

- 207 -


002 – Partition 4 Tamper/ Restore: R Receiver #1 RReceiver #3

001 – Partition 5 Alarm/ Restore: R Receiver #1 R Receiver #3



R Receiver #2 RReceiver #4
[350] Communicator Formats

(2-Digit decimal) 001 – Receiver 1: 003 – Receiver 3:
Range: 03= Contact ID, 04= SIA (Default) 002 – Receiver 2: 004 – Receiver 4:
- 208 -
[377] Communication Variables

(3-digit decimal)
Range: 000-255 attempts unless otherwise noted
001 – Swinger Shutdown Attempts: Alarms and Restore (000-014):
Default: 003 Tampers and Restore:
CP-01 Maintenance and Restore:

Default: 002
Communication Zone Delay
002 – Communication Delays: Default: 000
CP-01
Default: 030
AC Failure Communication Delay

Default:030 minutes/Hours
TLM Trouble Delay
NA Default: 010 checks
EN
Default:002 checks
Wireless Zone Low Bat. Transmission Delay
Default: 0000 days/hours
Delinquency Transmission Cycle Delay
Default: 030 days/hours
Communications Cancel Window
Default: 000 minutes
CP-01 Default: 005 minutes
003 – Periodic Test Transmission Cycle (Default: 030 hours/days):

Note: For UL installations, the periodic test transmissions default is 07 days.
004 – Periodic Test Transmission Time of Day (Default: 9999):

011 – Maximum Dialing Attempts: (Default: 005):
012 – Delay Between PSTN Attempts: (Default: 003 seconds):
013 – Delay Between Force Attempts: (Default: 020 seconds):
014 – Post Dial Wait for Handshake: (Range: 001-255; Default: 040 Seconds; UL=45):
015 – IP/Cellular Wait for Ack: (Range: 001-255; Default: 060 seconds):
016 – IP/Cellular Fault Check Timer: (Range: 003-255; Default: 010):

1 – R Communications Enabled
2 – o Restore on Bell Time-out
Description on page 125 3 – o Pulse Dialing
4 – o Pulse Dial after 5th Attempt
5 – o Parallel Communications
NA 6 – o Alternate Dial
EN 6 – R Alternate Dial
7 – o Reduced Dialing Attempts
- 209 -
8 – o Activity Delinquency

1 – o Keypad Ringback
Description on page 126 2 – o Bell Ringback
4 – o Closing Confirmation
8 – o Communications Priority Options

1 – o Test Transmission Reciever
2 – o Walk Test Communication
Description on page 127 4 – o Call Waiting Cancel
5 – oAlarm.com Enable/Disable
6 – o AC Failure Communication Delay in Hours
8 – o Tamper Limit

1 – o Phone Number Account Code
Description on page 127 2 – o 6-Digit Account Code
3 – oEthernet Enable
4 – oCellular Enable
5 – o Communicate FTC Events
[384] Communicator Backup Options

2 – R Backup Options - Receiver 2
Description on page 128 3 – o Backup Options - Receiver 3
4 – o Backup Options - Receiver 4
[385] Audio Module Talk/Listen Mask

1 –oTalk/Listen on Receiver 1
Description on page 128 3 –oTalk/Listen on Receiver 3
6.13 DLS Programming
[401] DLS/SA Options

1 – o Double Call
Description on page 129 2 – R User Enables DLS
3 – o DLS Callback
4 – o User Call up
6 – o Panel Call up and Baud Rate
7 – R Alt. Comm. DLS
[402] PSTN DLS Phone Number Programming

(31-digit phone number; Default: DFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF):
- 210 -
[403] DLS Access Code

(6-digit hex; 000000-FFFFFF; Default: 212800):
[404] DLS/SA Panel ID

(12-digit hex; 000000000000-FFFFFFFFFFFF)
[405] PSTN Double Call Timer

(3-decimal; 000-255; Default: 060):
[406] PSTN Number of Rings to Answer On

(3-decimal; 000-255; Default 000):
[407] SA Access Code

(6-digit hex; 000000-FFFFFF; Default: FFFFFF):
[410] Automatic DLS Options

001 – Auto DLS Options 1 – o Periodic DLS
3 – o DLS / Event Buffer 75% Full
8 – o DLS on Programming Change
002 – Periodic DLS Days (3-digit decimal; 000-255; Default: 000 days):
003 – Periodic DLS Time (4-digit decimal; HH:MM; 0000-2359; Default: 0000):
007 – Delay Call Window Start (4-digit decimal; 0000-2359; HH:MM) 1 – 0000 Delay Call Window Start
Default: 0000 2 – 0000 Delay Call Window End
6.14 Virtual Inputs
[560] Virtual Inputs

(3 digit decimal) 001 - Virtual Input 1: 017 - Virtual Input 17:
002 - Virtual Input 2: 018 - Virtual Input 18:
Description on page 131 003 - Virtual Input 3: 019 - Virtual Input 19:
Default: 000 004 - Virtual Input 4: 020 - Virtual Input 20:
- 211 -

6.15 Schedule Programming
[601] Programming Schedule 1

Interval 1 101 – Start Time: 102 – End Time:
103 – Days Assignment: 104 – Holiday Assignment:
(4- digit decimal) 01 – o Sunday o Holiday 1
HH:MM 02 – o Monday o Holiday 2
to HH:MM 03 – o Tuesday o Holiday 3
Default: 0000 04 – o Wednesday o Holiday 4
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
- 212 -
06 – o Friday
07 – o Saturday

05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday

- 213 -

05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday

HH:MM to HH:MM 02 – o Monday o Holiday 2
Default: 0000 03 – o Tuesday o Holiday 3
04 – o Wednesday o Holiday 4
05 – o Thursday
- 214 -
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
05 – o Thursday
06 – o Friday
07 – o Saturday
[711] Holiday Group 1

(6-Digit Decimal) 001 – Holiday Group 1 Date 1:
MMDDYY 002 – Holiday Group 1 Date 2:
Default: 000000 003 – Holiday Group 1 Date 3:
004 – Holiday Group 1 Date 4:
Description on
page 132
009-099 – Holiday Group 1 Date 9-99:

- 215 -

Description on
page 132

Description on
page 132

Description on
page 132
6.16 Audio Module Programming

[802] Audio Module Programming
2-digit entry
00= No station assigned
01 - 04 for audio stations 1-4
Default: 00
001 Zone 1 Station Assignment:
- 216 -

- 217 -

- 218 -

- 219 -

- 220 -

- 221 -

- 222 -
[802]
1 - o Tampers
2 - o Future Use
3 - R [A] Key Alarm
4 - R [P] Key Alarm
600 2-Way Audio Trigger Option 1
5 - R Duress Alarm
6 - R Opening After Alarm
7 - o Future Use
8 - o Zone Supervision Alarm
1 - o Future Use
2 - R Listen to all zones / Listen to zones in alarm
3 - o Future Use
4 - o Siren Active During 2-Way Audio
603 2-Way Audio Control Option 1
5 - o Hang-Up Auto Detection
6 - o User Call-In
7 - o For Future Use
8 - R 2-Way Audio Initiated by CS
1 - R Audio Capture Enable
2 - o Erase on FTC
3 - o Future Use
4 - o Future Use
605 Record Options
5 - o Future Use
6 - o Future Use
7 - o Future Use
8 - o Future Use
1 - o Audio Station 1 Record
606 Audio Station Record Control Option 1
5 - o Future Use
6 - o Future Use
7 - o Future Use
8 - o Future Use
Call Back / Recovery Window Duration:
610 2 digit entry
Default: 05 minutes
Call Back Acknowledge code:
611 6-digit entry
Default: 999999
Answering Machine Bypass:
612 2-digit entry
Default: 00
Double Call Timer:
613 2-digit entry
Default: 30
- 223 -
Number of Rings to Answer:

614 2-digit entry
Default: 00
Audio Duration:
615 2-digit entry
Default: 90
Record Time:
616 3-digit entry
Default: 105
Erase Time:
617 2-digit entry
Default: 15 minutes
1 - o Audio Station 1 Tamper
620 Audio Station Tamper Option 1:
5 - o Future Use
6 - o Future Use
7 - o Future Use
8 - o Future Use
999 Reset Module Programming to Factory Defaults 999 installer code 999
6.17 Wireless Programming
[804] Wireless Programming

See the HSM2HOSTx installation manual and wireless device installation sheets for detailed information.
000 – WLS Device Enrollment Zones: (Selection) Zone #:
Zone Definition:
(2-digit decimal) Partition Assignment:
(14 x 2) Zone Label:
This section is an overview of wireless device programming. See the
associated device installation sheets and the HSM2HOST/RFK keypad WLS Keys (Selection) WLS Key #:
installation instructions for detailed worksheets.
(Selection) Select User:
WLS Key Label:
Sirens (Selection) Siren #:
(14 x 1) Siren Label:
Keypads (2-digit decimal) Keypad #:
Keypad Label:
Repeaters (Selection) Repeater #:
Repeater Label:
- 224 -
001- 248 Configure Wireless Zones 1 to 248

551-556 Configure Wireless Sirens 1-16
601-632 Configure Wireless Keys 1-32
701-716 Configure Wireless Keypads
801-810 Wireless Options
841 Visual Verification Programming
901-905 Delete Wireless Devices
921-925 Replace Wireless Devices
990 Show All Devices
999 Reset Devices to Factory Default
6.18 Alternate Communicator
[850] Cellular Signal Strength

[851] Communicator Programming

Local IP configuration
Default (000.000.000.000)
[002] Ethernet IP Subnet Mask
Default (255.255.255.000)
Default (000.000.000.000)
[004] Receiver Supervision Interval
Default (00087/135)
Valid range: 00000 - 65535
[005] System Toggle Options 1 o 1 - Receiver 1 Supervised
o 2 - Receiver 3 Supervised
o 3 - Heartbeat 1
o4 - Cell Primary
R6 - Remote Firmware Upgrade
o7 – Test TX
o8 – Low Signal Mask
[006] System Toggle Options 2 R 1 - Receiver 1 Enabled
R 2 - Receiver 2 Enabled
R 7 - DLS Over Cellular
o 8 - Network Trouble Suppression
Default (000.000.000.000)
- 225 -

Default (000.000.000.000)
[010] System Toggle Options 3 o 1 - 2-Way Audio Over Cellular
o 2 - Visual Verification Default
o 3 - Video On Demand
o 4 - Receiver Group
DLS configuration
[012] DLS Incoming Port
Default (03062)
Valid range: 00000 - 65535
[013] DLS Outgoing Port
Default (03066)
Valid range: 00000 - 65535
[015] DLS Call-Up IP
Default (000.000.000.000)
[016] DLS Call-Up Port
Default (00000)
Valid range: 00000 - 65535
[018] Receiver Group Pair
Default (0000)
Valid range: 0000 - FFFF
[020] Time Zone
Default (00)
Valid range: 00 - 99
Reporting codes
[025] Radio Activation Restore
Default (FF)
Program 00 disable or FF enable
[026] Receiver 1 Test Transmission
Default (FF)
Default (00)
Default (FF)
Default (00)
[030] FTC Restore [080]
Default (FF)
[080] TFTP UDP server IP address
Default (000.000.000.000)
- 226 -
[081] TFTP UDP server port number

Default (0C11)
[082] TFTP UDP local port
Default (0C12)
[083] TFTP UDP server DNS
Default ( ) 32 ASCII characters
DLS SA configuration
[095] DLS SA Incoming Local Port
Default (03092)
Valid range: 00000 - 65535
[096] DLS SA Outgoing Local Port
Default (03093)
Valid range: 00000 - FFFFF
Ethernet receiver 1 configuration
[101] Receiver 1 Account Code
Default (0000000000)
Valid range: 0000000001 - FFFFFFFFFE
[102] Receiver 1 DNIS
Default (000000)
Valid range: 000000 - FFFFFF
[103] Receiver 1 IP Address
Default (127.000.000.001)
[104] Receiver 1 UDP Remote Port
Default (03061)
Valid range: 00000 - 65535
[105] Receiver 1 UDP Local Port
Default (03060)
Valid range: 00000 - 65535
[106] Receiver 1 Domain Name
Ethernet receiver 2 configuration
Default (0000000000)
Default (000000) Valid range: 000000 - 0FFFFF
Default (000.000.000.000)
[114] Receiver 2 UDP Remote Port
Default (03061)
Valid range: 00000 - 65535
- 227 -
[115] Receiver 2 UDP Local Port

Default (03065)
Valid range: 00000 -65535
[124] Ethernet Test Transmission Time
Default (9999)
Valid: 00-23(HH); 00-59(MM)
[125] Ethernet Test Transmission Cycle
Default (000000)
Valid range: 000000 - 999999 minutes
Cellular receiver 3 configuration
Default (0000000000)
Default (000.000.000.000)
[204] Receiver 3 Port
Default (03061)
Valid range: 00000 - 65535
[205] Receiver 3 APN
Cellular receiver 4 configuration
Default (0000000000)
Default (000.000.000.000)
[214] Receiver 4 Port
Default (03061)
Valid range: 00000 - 65535
[215] Receiver 4 APN
System cellular configuration
[221] Cellular Public Access Point Name
- 228 -
[222] Cellular Login User Name

[223] Cellular Login Password
[224] Cellular Test Transmission Time of Day
Default (9999)
Valid range: 00 - 23 hrs. (HH) 00 - 59 min. (MM)
[225] Cellular Test Transmission Cycle
Default (000000)
Valid range: 000000 - 999999 minutes
[226] Network Trouble Delay Timer
Default (015)
Valid entries from 000 to 255
2-Way audio over cellular options
[227] Voice Call Timeout
Default (000)
[228] Voice Call Back Time
Default (010)
[229] Voice Call Back Number
Default ( ) 32 digit phone number.
Valide entries:: 000000000000000 to FFFFFFFFFFFFFFF
Integration session 1
[422] Integration Identification Number
Default (MAC/IMEI) Read only
[423] Session 1 Integration Access Code
Default (12345678123456781234567812345678)
Valid range: 00000000000000000000000000000000 - FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
[424] Session 1 SMS Label
Default (11111111) 16 ASCII characters
[425] Session 1 Integration Toggle Options 2 o1 – Integration Over USB
o2 – Integration Over Cellular
o3 – Integration Over Ethernet
o4 - Reserved
R5 – ITv2 Integration Protocol
o6 - Reserved
o7 - Reserved
o8 - Reserved
[426] Session 1 Integration Toggle Options 3 o1 – UDP Polling
o2 – TCP Polling
o3 – Real-time Notification
o4 – Notification Follows Poll
o5 – Firewall IP
- 229 -
o6 - Reserved
o7 - Reserved
o8 - Reserved
[427] Session 1 Interactive Polling Interval
Default (00010)
Valid range: 00000- 65535 seconds
[428] Session 1 Integration Server IP
Default (000.000.000.000)
[429] Session 1 Integration Notification Port
Default (00372)
Valid range: 00000- 65535
[430] Session 1 Integration Polling Port
Default (03073)
[431] Session 1 Integration Server DNS
32 ASCII characters
[432] Session 1 Integration Outgoing Port
Default (03070)
[433] Session 1 Integration Incoming Port
Default (03071)
Integration sessions 2-4
[450] - [460] Repeats [423] - [433] for Session 2
Notification controls
R1 – Alarm and Alarm Restore
[691] Session 1 Notification Control
Notifications
R2 –Tamper and Tamper Restore
Notifications
R3 – Arming and Disarming Notifications
R4 – Trouble and Trouble Restore
Notifications
R5 – Test Transmission Notifications
R6 – Reserved
R7 – Reserved
R8 –Reserved
Notifications
Notifications
Notifications
- 230 -

R6 – Reserved
R7 – Reserved
R8 –Reserved
Notifications
Notifications
Notifications
R6 – Reserved
R7 – Reserved
R8 –Reserved
Notifications
Notifications
Notifications
R6 – Reserved
R7 – Reserved
R8 –Reserved
Receiver test
[901] Receiver Test o1 –Receiver 1
o2 –Receiver 2
o3 –Receiver 3
o4 –Receiver 4
o6 – Reserved
o6 – Reserved
o7 – Reserved
o8 –Reserved
Radio diagnostics
[976] Configuration File Version
[977] Cellular NetworkProvider - MCC/MNC Code
[978] Cellular Network Type
[979] Cellular Network CSQ
[980] Radio Reset Codes
[981] Radio Type
[982] Radio Firmware Version
[983] Firmware Update Diagnostics Section
- 231 -
[984] Communicator Status

[985] Radio Initialization Status
[986] System Toggle Options 4 o1 –Remote Shutdown Enable Default
Communicator information
[987] Language Version
[988] DNS 1 IP Address
[989] DNS 2 IP Address
[990] Boot Loader Version
[991] Firmware Version
[994] Cellular IP Address
[995] SIM Number
[996] Cellular Telephone Number
This number is required for DLS and Firmware upgrades
[997] IMEI Number
[998] MAC Address
6.19 Keypad Programming

[860] Display Keypad Slot Number
[861]-[876] Keypad Programming
Refer to the installation instructions provided with the keypad for details.
000 – Keypad Partition Mask 00 – Global
01 – R Partition 1 05 – o Partition 5
02 – o Partition 2 06 – o Partition 6
001 – Function Key 1 (Default: 03):
Function Key Programming Options: Function Key Programming Options:
- 232 -
00 - Null Key
02 - Instant Stay Arm 17 - Arm Interior 37 - Time/Date Programming
03 - Stay Arm 21 - Command Output 1 39 - Trouble Display
04 - Away Arm 22 - Command Output 2 40 - Alarm Memory
05 - [*][9]No Entry Arm 23 - Command Output 3 61 - Partition Select 1
06 - Chime On/Off 24 - Command Output 4 62 - Partition Select 2
07 - System Test 29 - Bypass Group Recall 63 - Partition Select 3
09 - Night Arm 31 - Local PGM Active 64 - Partition Select 4
12 - Global Stay Arm 32 - Bypass Mode 65 - Partition Select 5
13 - Global Away Arm 33 - Bypass Recall 66 - Partition Select 6
14 - Global Disarming 34 - User Programming 67 - Partition Select 7
15 - Temperature 35 - User Functions 68 - Partition Select 8
16 - Quick Exit
011 – Keypad I/O (Zone number or output number; 3-digit decimal; Default: 000):
012 – Local PGM Output Timer Pulse Time Minutes (Default: 00 minutes)
Pulse Time Seconds (Default: 05 seconds)
021 – Keypad Option 1 1 – R[F] Key Enabled
For systems compliant with EN50131-1 and
EN
EN50131-3 Section [021]: options 1 and 2
must be OFF.
2 – R R[M] Key Enabled
2-digit decimal
3 – R R[P] Key Enabled
4 – R Display Code or X’s
022 – Keypad Option 2 1 – R Local Clock Display
2 – o Local Clock 24-Hour
3 – R Auto Alarm Scroll
5 – R Power LED
6 – R Power LED AC Present
7 – R Alarms Displayed While Armed
8 – R Auto Scroll Open Zones
023 – Keypad Option 3 1 – o Armed LED Power Save
2 – R Keypad Status Shows Arm Mode
3 – o 5th Terminal is PGM Output/Zone Input
4 – o Prox Tag Arm/Disarm
7 – o Local Display of Temperature
8 – o Low Temperature Warning
030 – LCD Message:
031 – Downloaded LCD Message Duration (3-digit decimal; 000-255; Default: 000):
041 – Indoor Temperature Zone Entry (3-digit decimal; 000-248; Default: 000):
042 – Outdoor Temperature Zone Entry (3-digit decimal; 000-248; Default: 000):
101-228 – Door Chime Sound: 00 – o Disabled
01 – R 6 Beeps
02 – o Bing Bong
- 233 -
03 – o Ding Dong
04 – o Alarm Tone
05 – o Zone Name
Door Chime Zone Assignment:
1 _____ 19 ____ 37 ____ 55 ____ 73 ____ 91 ____ 109____ 127____ 145____ 163____ 181 ____199 ____ 217 ____235 ____
2 _____ 20 ____ 38 ____ 56 ____ 74 ____ 92 ____ 110____ 128____ 146____ 164____ 182 ____200 ____ 218 ____236 ____
3 _____ 21 ____ 39 ____ 57 ____ 75 ____ 93 ____ 111____ 129____ 147____ 165____ 183 ____201 ____ 219 ____237 ____
4 _____ 22 ____ 40 ____ 58 ____ 76 ____ 94 ____ 112____ 130____ 148____ 166____ 184 ____202 ____ 220 ____238 ____
5 _____ 23 ____ 41 ____ 59 ____ 77 ____ 95 ____ 113____ 131____ 149____ 167 ____ 185 ____203 ____221 ____239 ____
6 _____ 24 ____ 42 ____ 60 ____ 78 ____ 96 ____ 114____ 132____ 150____ 168 ____ 186 ____204 ____222 ____240 ____
7 _____ 25 ____ 43 ____ 61 ____ 79 ____ 97 ____ 115____ 133____ 151____ 169 ____ 187 ____205 ____223 ____241 ____
8 _____ 26 ____ 44 ____ 62 ____ 80 ____ 98 ____ 116____ 134____ 152____ 170 ____ 188 ____206 ____224 ____242 ____
9 _____ 27 ____ 45 ____ 63 ____ 81 ____ 99 ____ 117____ 135____ 153____ 171 ____189 ____207 ____ 225 ____243 ____
10 ____ 28 ____ 46 ____ 64 ____ 82 ____ 100 ___ 118____ 136____ 154____ 172 ____190 ____208 ____ 226____ 244 ____
11 ____ 29 ____ 47 ____ 65 ____ 83 ____ 101 ___ 119____ 137____ 155____ 173 ____191 ____209 ____ 227____ 245 ____
12 ____ 30 ____ 48 ____ 66 ____ 84 ____ 102____ 120____138____ 156____ 174 ____192 ____210 ____ 228 ____246 ____
13 ____ 31 ____ 49____ 67_____ 85 ____ 103____ 121____139____ 157____ 175_____193 ____211 ____ 229 ____247 ____
14 ____ 32 ____ 50 ____ 68_____86 ____ 104____ 122____140____ 158____ 176_____194 ____212 ____ 230 ____248 ____
15 ____ 33 ____ 51 ____ 69_____87 ____ 105____ 123____141____ 159____ 177_____195 ____213 ____ 231 ____
16 ____ 34 ____ 52 ____ 70_____88 ____ 106____ 124____142____ 160____ 178_____196 ____214 ____ 232 ____
17 ____ 35 ____ 53 ____ 71_____89 ____ 107____ 125____143____ 161____ 179_____197 ____215 ____ 233 ____
18 ____ 36 ____ 54 ____ 72_____90 ____ 108____ 126____144____ 162____ 180_____198 ____216 ____ 234 ____
6.20 Template Programming
[899] Template Programming

5 Digit Template Code:
Central Station Phone Number:
Description on page 72 Central Station Account Code:
Partition Account Code:
DLS Access Code:
Partition 1 Entry Delay 1:
Partition 1 Exit Delay:
Installer Code:
6.21 System Information
[900] System Information

000 – Control Panel Version
- 234 -
001- 016 – View Keypad 1-16 Version

101-116 – HSM2108 8 Zone Module 1-15 Version
201-215 – HSM2208 8 Output Module 1 Version
301-315 – HSM3408 8 I/O Expansion Module
461 – HSM2Host Module
481 – HSM2955
501-504 – HSM2300 Power Supply 1A Module
521-524 – HSM2204 High-Current O/P Module
550-554 – HSM3350 3A Power Supply Module
601-608 – HSM3204CX Corbus Repeater
[901] Installer Walk Test Mode Enable/Disable

6.22 Module Programming
[902] Add/Remove Modules

Description on page 149 000 – Auto Enroll Modules
001 – Enroll Modules
002 – Slot Assignment
003 – Edit Module Slot Assignment
101 – Delete Keypads
102 – Delete HSM2108 8 Zone Module
103 – Delete HSM2208 8 Output Module or High Current O/P
104 – Delete HSM3408 8 I/O Expansion Module
106 – Delete HSM2Host
108 – Delete HSM2955
109 – Delete HSM2300 Power Supply 1A
110 – Delete HSM2204 4 High Current Output
111 – Delete HSM3350 3A Power Supply Module
112 – Delete HSM3204CX Corbus Repeater
[903] Confirm Modules

000 – View All Modules
Description on page 150 101 – Confirm Keypads
102 – ConfirmHSM2108 8 Zone Module
103 – Confirm HSM2208 8 Output Module or High Current O/P
104 – Confirm HSM3408 8 I/O Expansion Module
106 – Confirm HSM2Host
108 – Confirm HSM2955
109 – Confirm HSM2300 Power Supply 1A
110 – Confirm HSM2204 4 High Current Output
111 – Confirm HSM3350 3A Power Supply Module
112 – Confirm HSM3204CX Corbus Repeater
- 235 -
6.23 Wireless Placement Testing

Testing
[904] Wireless Placement Test

001-248 – Placement Test - Zone 1-248
521-528 – Placement Test Repeaters 1-8
551-558 – Placement Test Sirens 1-8
601-632 – Placement Test Wireless Keys 1-32
701-716 – Placement Test Wireless Keypads 1-16
[911] Diagnostics
000 - Panel Diagnostics
001-016 - Keypad 001 to 016
101-115 - Zone Expander 001 to 015
301-315 - 8 I/O Expander 001 to 015
501-504 - Power Supply 001 to 004
521-524 - High Current Output Battery 001 to 004
551-554 - 3 A Power Supply 001 to 004
601-608 - Corbus repeater 001 to 008
[912] Zone Soak Test

000 – Zone Soak Test Duration (3-digit decimal; 001-255 Days; Default: 014):
001 – Zone Soak Test Assignment - Zones 1-8
- 236 -

6.24 Battery Settings
[982] Battery Settings

000 – Panel Battery Settings 01 – o Panel High Charge Current
010 – HSM2204 High Current Output Battery 01 – o HSM2204 1 High Charge Current
02 – o HSM2204 2 High Charge Current
020 – HSM2300 1A Power Supply Battery 01 – o HSM2300 1 High Charge Current
030 – HSM3204CX Corbus Repeater Battery Settings 01 – oHSM3204CX 1 High Charge Current
02 – oHSM3204CX 2 High Charge Current
- 237 -
040 – HSM3350 Module 1 Battery Settings 001 01 – o HSM3350 Battery 1 High Charge
02 – o HSM3350 Battery 2 High Charge
03 – R HSM3350 Battery 2 Enable
040 – HSM3350 Module 2 Battery Settings 002 01 – o HSM3350 2 High Charge Current
6.25 Restoring Factory Defaults
[989] Default Master Code
[990] Installer Lockout Enable/Disable
[991] Default Keypads

999 – Default All Keypads
901-916 – Default Keypad 1-16
[996] Default HSM2HOST Wireless Receiver
[988] Default HSM2955
[999] Default System

(Descriptions on page 152)
- 238 -
Section 7: Troubleshooting
7.1 Testing
l Power up system
l Program options as required (See "Programming descriptions" on page 75)
l Trip, then restore zones
l Verify correct reporting codes are sent to the central station
7.2 Troubleshooting
LCD programmable-message keypad:
l Press [*][2] followed by access code if required to view a trouble condition
l The trouble light flashes and the LCD displays the first trouble condition
l Use the arrow keys to scroll through all trouble conditions present on the system
Note: When additional information is available for a specific trouble condition, a [*] is displayed. Press the [*] key to view the
additional information.
[*][2] Trouble summary

The list below describes the trouble indications displayed on keypads.
Trouble Detailed Trouble
01 – Bell circuit 06 – USB Wi-Fi Connected
02 – RF jam detected 07 – Power Unit Fail (System)
01 – Service Required 03 – Loss of clock 08 – Power Unit Failure (HSM3204CX Corbus Repeater)
04 – Output 1 fault 09 – Power Unit Failure (HSM3350 3 A Power Supply)
05 – Warm start 10 – Overcurrent
01 – Panel low battery 10 – HSM3204CX low battery
02 – Panel no battery 11 – HSM3204CX no battery
04 – HSM2204 1-4 low battery 13 – HSM3350 low battery 1
02 – Module Low Battery
05 – HSM2204 1-4 no battery 14 – HSM3350 low battery 2
07 – HSM2300 1-4 low battery 15 – HSM3350 no battery 1
08 – HSM2300 1-4 no battery 16 – HSM3350 no battery 2
01 – HSM2HOSTx voltage 08 – HSM2208 1-4 voltage
02 – Keypad 1-16 voltage 09 – HSM2955 1-4 voltage
04 – HSM2108 1-15 voltage 10 – HSM3408 voltage
03 – Bus Voltage
05 – HSM2300 1-4 voltage 11 – HSM3204CX bus low voltage
06 – HSM2204 1-4 voltage 12 – HSM3204CX bus fault
07 – Panel Corbus Output Fault (system) 13 – HSM3350 bus low voltage
01 – Zone 1-248 AC
06 – HSM2204 1-4 AC
02 - Keypad AC Trouble
07 – Alarm controller AC
04 – AC Troubles 03 – Siren 1-16 AC
08 – HSM3204CX AC
04 – Repeater 1-8 AC
09 – HSM3350 AC
05 – HSM2300 1-4 AC
- 239 -
Trouble Detailed Trouble

08 – Heat trouble
01 – Zone 001 - 248
09 – CO trouble
03 – Siren 1-16
05 – Device Faults 10 – Freeze trouble
04 – Repeater 1-8
11– Probe disconn.
06 – Device mask
12– Fire trouble
01 – Zone 1-248
04 – Repeater 1-8
06 – Device Low Battery 02 – Keypad 1-16
05 – User 1-32
03 – Siren 1-16
01 – Zone 1-248 04 – Repeater 1-8
07 – Device Tampers
03 – Siren 1-16 05 – Audio Station 01 - 04
01 – Zone 1-248 03 – Siren 1-16
08 – RF Delinquency
02 – Keypad 1-16 04 – Repeater 1-8
01 – HSM2HOSTx 08 – HSM2208 1-4
02 – Keypad 1-16 09 – HSM2955
09 – Module Supervisory 04 – HSM2108 1-30 11 – HSM3408
05 – HSM2300 1-4 12 – HSM3204CX
06 – HSM2204 13 – HSM3350
01 – HSM2HOSTx 08 – HSM2208 1-4
02 – Keypad 1-16 09 – HSM2955
10 – Module Tamper 04 – HSM2108 1-30 11 – HSM3408 1-30
05 – HSM2300 1-4 12 – HSM3204CX
06 – HSM2204 13 – HSM3350
01 – TLM 06 – Receiver 1-4 absent
02 – FTC Receiver 1-4 07 – Receiver 1-4 supervision
11 – Communications
04 – Alt. comm cellular 09 – Alt. comm fault
05 – Alt. comm Ethernet 10 – Alt. comm FTC trouble
01 – Zone 1-248
04 – Repeater 1-8
12 – Not Networked 02 – Keypad 1-16
05 – User 1-32
03 – Siren 1-16
05 – HSM2300 10 – HSM3408
06 – HSM2204 11 – HSM3204CX
13 – AUX Trouble
07 – System area 12 – HSM3350 AUX 1 trouble
13 – HSM3350 AUX 2 trouble
01 – Interactive Zone
14 – Limit Exceeded Trouble
02 – Interactive Partition
Trouble [1] Service Required Press [01] to determine specific trouble
Trouble Troubleshooting
Disconnect Bell-/+ leads and measure resistance:
[01] Bell Circuit
Open circuit indicates break in wiring or defective siren/bell.
Bell+, Bell-.open circuit.
Jumper Bell+/- with 1K resistor (Brown, Black, Red):
Check event buffer to determine specific trouble.
[02] RF Jam Detected
If buffer logs RF jam, check for RF interference.
Wireless receiver - excessive noise detected.
Disable RF Jam: section [804] sub-section [801].
- 240 -
Trouble [1] Service Required Press [01] to determine specific trouble

To program the time and date:
Enter [*][6][Master Code] then press [01].
[03] Loss of clock Enter the time and date (24-hour clock) using the following format: HH:MM
The alarm controller internal clock is not set . MM/DD/YY
e.g.,. For 6:00 pm, June 29, 2010:
Enter: [18] [00] [06] [29] [10]
If output #1 is unused: ensure terminals O1, AUX are jumpered with 1K resistor
(brown, black, red).
[04] Output 1 Fault
If output #1 is used: disconnect wire leads from O1, AUX terminals, measure
HSM2204 output #1 open circuit. resistance of leads:
Open circuit indicates a break in wiring.
[05] Warm Start This trouble automatically restores after two minutes or when acknowledge via the [*]
Control panel has recovered from a software lockup 2 menu. Contact Tech Support if this trouble persists or re-occurs periodically.
[06] USB Wi-Fi Connected The trouble automatically clears once the HSM3WIFI adapter is unplugged from the
HSM3WIFI USB to Wi-Fi Adapter is plugged into the panel. This trouble serves as a warning as to not to forget to unplug the adapter when
panel configuration via Wi-Fi is completed.
[07] Power Unit Fail (System)

Ensure the combined output power of the panel is not exceeding 2A. Power cycle the
A fault with the internal power supply has been detected panel and if the trouble persists it may indicate a permanent hardware failure.
on the panel.
[08] Power Unit Failure (HSM3204CX) Ensure the combined output power of the corbus repeater module is not exceeding
A fault with the internal power supply has been detected 2A. Power cycle the module and if the trouble persists it may indicate a permanent
on the corbus repeater. hardware failure.
[09] Power Unit Failure (HSM3350) Ensure the combined output power of the 3A power supply module is not exceeding
A fault with the internal power supply has been detected 3A. Power cycle the module and if the trouble persists it may indicate a permanent
on the 3A power supply. hardware failure.
[10] Overcurrent
Reduce the load on the panel by re-powering modules or detectors with a separate
The combined output power on the panel has exceeded power supply module.
2A for a period of more than 5 minutes.
Trouble [2] Module Battery Trouble Press [02] to determine specific trouble
[01] Panel Low Battery Verify voltage measured across DC input terminals is 16-18 VAC. Replace
The panel detects that the battery is below the low battery HSM65W power supply adapter if required.
threshold (less than 11.5VDC). Connect battery, remove AC power.
NOTE: This trouble condition will not clear until the battery Verify measured voltage across Aux terminals is 12.5VDC min.
voltage is 12.5VDC min., under load. NOTE: If battery is
new allow 1 hour to charge. Replace battery if it is no longer able to hold a charge due to age.
Verify battery is connected.

[02] Panel No Battery
Ensure battery leads are connected with the right polarity.
The panel detects that no battery is present or that the
Connect battery, remove AC power.
battery is shorted.
Verify measured voltage across Aux terminals is 12.5VDC min
[04] 4 High Current output 1-4 Low Battery (HSM2204) Verify voltage measured across DC input terminals is 16-18 VDC. Replace
HSM65W power supply adapter if required.
HSM2204 battery less than 11.5VDC.
NOTE: This trouble condition will not clear until the battery
voltage is 12.5VDC min., under load. Charge battery. It may Verify measured voltage across Aux terminals is 12.5VDC min.
be low due to a long period without AC. Replace battery if it is no longer able to hold a charge due to age.
- 241 -
Trouble [2] Module Battery Trouble Press [02] to determine specific trouble
[05] 4 High Current output 1-4 No Battery (HSM2204)
Enter 05 to view which HSM2204 does not have a battery
connected.
Verify voltage measured across DC input terminals is 16-18 VAC. Replace
[07] Power Supply 1-4 Low Battery (HSM2300) HSM65W power supply adapter if required.
Enter 07 to view which HSM2300 has a battery voltage less Connect battery, remove AC power.
than 11.5V. Verify measured voltage across Aux terminals is 12.5VDC min.
Replace battery if it is no longer able to hold a charge due to age.
[08] Power Supply 1-4 No Battery (HSM2300)
connected.
[10] HSM3204CX low battery HSM65W power supply adapter if required.
Enter 10 to view which HSM3204X has a battery voltage Connect battery, remove AC power.
less than 11.5V
Verify measured voltage across Aux terminals is 12.5VDC min.
[11] HSM3204CX no battery HSM65W power supply adapter if required.
Enter 11 to view which HSM3204CX does not have a Connect battery, remove AC power.
battery connected.
[13] HSM3350 low battery 1 HSM65W power supply adapter if required.
than 11.5V.
[14] HSM3350 low battery 2 HSM65W power supply adapter if required.
than 11.5V. Verify measured voltage across Aux terminals is 12.5VDC min.
[15 ] HSM3350 no battery 1
connected.
[16] HSM3350 no battery 2
connected
- 242 -
Trouble [3] Bus Voltage Trouble Press [03] to determine specific trouble
[01] HSM2HOST Bus Low Voltage
The 2-way wireless integration module has detected a
voltage less than 6.3V on its aux input.
[02] Keypad 1-16 Bus Low Voltage
Enter 02 to view hardwired keypads with a bus voltage of
less than 6.9V for models that include a wireless
transceiver, 7.7V for the models that do not.
[04] HSM2108 Bus Low Voltage
Enter 04 to view zone expanders with a bus voltage of
less than 5.9V.
Enter 05 to view power supplies with a bus voltage of less
than 6.9V.
Enter 06 to view high current output modules that have
Ensure voltage at module is higher than the documented limits.
detected a bus voltage of less than 6.9V.
Ensure wire run is not too long.
[07] Panel Corbus Fault The panel has detected that its
corbus output voltage is less than 9.0V or higher than Check voltage of panel battery.
15V Trouble should clear when AC is re-applied and the battery has had time to charge.
[08] HSM2208 Bus Low Voltage Disconnect AC and allow the panel to run on battery power. Ensure voltage at module
is higher than the documented limits.
The low current output module has detected a voltage
less than 5.9V on its aux input. Ensure that the corbus is not being overloaded or that there is no short anywhere on
the wire run.
The audio module has detected a voltage less than
9.65V on its aux input.
[10] HSM3408 voltage
The audio module has detected a voltage less than 6.4V
on its aux input.
[11] HSM3204CX bus low voltage
The audio module has detected a voltage less than 6.0V
on its aux input.
[12] HSM3204CX bus fault
Enter 12 to view corbus repeaters which have detected
the voltage on the corbus output is less than 9.0V
[13] HSM3350 bus low voltage
Enter 12 to view corbus repeaters which have detected
the voltage on the corbus output is less than 6.0V
- 243 -
Trouble [4] AC Failure Press [04] to determine specific trouble
[01] Zone 1-248 AC
[03] Siren 1-16 AC
[04] Repeater 1-8 AC
[05] HSM2300 1-4 AC Verify voltage measured across DC input terminals is 16-20VDC. Replace HSM65W
power adapter if required.
[06] HSM2204 1-4 AC
For the HSM2204 or HSM2300 modules, ensure a 40VA 16.5VAC transformer is
[07] Alarm Controller being used. Terminal voltage should be 16-17VAC. Replace transformer if required.
[08] HSM3204CX AC
[09] HSM3350 AC
An AC trouble has been detected on a device or module.
- 244 -
Trouble [05] Device Faults Press [05] to determine specific trouble
Fire Trouble:
Ensure that, if the PGM-2 is configured as 2-Wire Smoke detector and not used, 5.6K EOL resistor
When a Fire Trouble is generated at the [05] Device faults ie is used.
Device Faults > Fire Trouble
Ensure fire zones have a 5.6K resistor (green, blue, red) connected.
Remove wire leads from Z and COM terminals and measure resistance of the wire
[01] Zone 1-248 faults
leads:
Wireless zones:
Check for a short on DEOL zones or an open condition on SEOL fire zones.
Enter [01] to view zones in fault. This trouble is
Connect a 5.6K resistor across the Z and COM terminals. Verify the trouble condition
generated by a zone wireless supervisory trouble.
clears.
Placement test a wireless device and re-locate it if bad results are received.
Hardwired zones:
This trouble is generated by a short on hardwired zones .
when DEOL or TEOL is used.
[03] Siren 1-16 faults
This trouble is caused by a wireless supervisory fault on a Placement test the wireless siren and re-locate if needed.
wireless siren.
[04] Repeater 1-8 faults
This trouble is caused by a wireless supervisory fault on a Placement test the wireless repeater and re-locate if needed.
wireless repeater, or by the repeater shutting down due
to a loss of AC/DC power.
[06] Device mask
Enter [06] to view the zone label in masking condition. A
Refer to the device manual to troubleshoot conditions that may cause masking detection for that
zone programmed as 24H Anti- Masking or a wireless devices sensors.
device has detected a masking condition with one of its
sensors.
[08] Heat trouble
Move the device to a location with room temperature and ensure the trouble clears. If not check the
Enter 10 to view the wireless zone which is detecting low programming threshold for high temperature for the zone.
temperature.
[09] CO trouble
Enter 09 to view the zone of a CO wireless device that is Refer to the CO devices manual for troubleshooting steps for low sensitivity trouble.
in low sensitivity trouble.
[10] Freeze trouble
Move the device to a location with room temperature and ensure the trouble clears. If not check the
Enter 08 to view the wireless zone which is detecting high programming threshold for low temperature for the zone.
temperature.
[11] Probe disconn.
Enter [11] to view the wireless zone which has detected a Refer to the temperature or flood detectors manual for troubleshooting steps for probe disconnected.
disconnect probe.
[12] Fire trouble If fire zone is a wireless smoke, ensure it is not tampered, or in supervisory trouble. Ensure the
smoke chamber is cleared of dust. If a 2wire smoke is used ensure a 2.2K EOL resistor is used. If
Enter [012] to view which zones are in Fire trouble. zone is a 4 wire smoke, ensure a 5.6K EOL resistor is used.
- 245 -
Trouble [6] Device Low Battery Press [06] to toggle through specific devices with low battery trouble
[01] Zones 1-248
[02] Keypad 1-16
[03] Siren 1-16
View which device is in low battery through the [*][2] menu.
[04] Repeater 1-8
Replace the batteries in the device with same battery type.
[05] User 1-32
Verify that tamper and low battery condition is cleared and reported.
One or more wireless devices has a low battery.
Verify zone operation.
NOTE: The event is not logged to the event buffer until
the wireless device low battery delay time expires.
Programming section [377], Opt 002.
Trouble [7] Device Tamper Press [07] to determine specific trouble
[01] Zone 1-248 tampers
[02] Keypad 1-16 tampers Check that the tamper switch is securely attached to the wall.
[03] Siren 1-16 tampers Remove the wire leads from I/O and COM and measure the resistance of the wire
[04] Repeater 1-8 tampers leads.
[05] Audio Station 1-4 tampers Connect a 5.6K resistor (Green, Blue, Red) across the I/O and COM terminals.
An open circuit is present on one or more zones with Verify the trouble condition clears.
DEOL or TEOL resistors enabled.
Ensure device cover is secure.
A tamper condition is present on one or more wireless
Ensure device is correctly mounted for wall tamper operation.
devices.
Trip, then restore the tamper. If tamper condition persists, replace wireless device.
Trouble [8] RF Delinquency Press [08] to determine specific trouble
[01] Zone 1-248 faults Open/close the device, press a key on the keypad or tamper/restore.
[02] Keypad 1-16 faults Ensure the device is physically present.
[03] Siren 1-16 faults Check for device faults (e.g., low battery).
[04] Repeater 1-8 faults Check the current signal strength and during the last 24 hours.
HSM2HOST has not received a supervisory signal from Replace the battery.
a wireless device for 20 minutes. Replace the device.
- 246 -
Trouble [9] Module Supervisory Press [09] to determine specific zones with a tamper trouble
[01] HSM2HOST
[02] Keypad 1-30
[04] HSM2108 1-15
Ensure the module is physically connected to the corbus.
[05] HSM2300 1-4
Measure power across corbus Red and Blk directly on the module and ensure its at
[06] HSM2204 1-4 least 10.5V.
[08] HSM2208 1-4 Remove the module from the bus and wire it directly at the panel. If trouble clear it
[09] HSM2955 indicates a wiring issue with were it was previously mounted. If the trouble doesn't
clear, replace the module.
[10 ]HSM3408 1-30
Its its an old removed, or replaced module, ensure it gets deleted via section [902].
[11] HSM3204CX 1-8
[12] HSM3350 1-4
No supervisory response from enrolled module.
Trouble [10] Module Tamper Press [10] to determine specific trouble
[01] HSM2HOST
[02] Keypad 1-16
Ensure the TAM terminal, if present on the
[04] HSM2108 1-30
modules is shorted to ground if tamper support is not used.
[05] HSM2300 1-4
Ensure module cabinet cover is securely closed and properly activating the tamper
[06] HSM2204 1-4 switch, if present.
[08] HSM2208 1-4 Ensure for the Keypads that the rubber tamper plunger is installed on the back plastics
[09] HSM2955 and that the keypad is securely closed and fastened to the wall.
[10] Alt. comm. For the HSM2HOST ensure module is securely closed and correctly mounted for wall
[11] HSM3408 1-30 tamper operation.
[12] HSM3204CX 1-8 Manually trip, then restore the tamper. If tamper condition persists, replace the
module.
[13] HSM3350 1-4
A tamper condition is present on one or more modules.
Trouble [11] Communications Press [11] to determine specific trouble
Measure the voltage across TIP and RING on the panel:
No phone off-hook – 50VDC (approx).
[01] Phone Line Trouble
Any phone off-hook – 5VDC (approx).
Phone line voltage at TIP, RING on main panel less than
Wire incoming line directly to TIP and RING.
3VDC.
If trouble clears, check wiring or the RJ-31 phone jack.
If not using a phone line on the panel, disable it in section [015] option 7.
[02] FTC Receiver 1-4
If using PSTN communications, ensure the central station phone number is
The system failed to communicate with a receiver using programmed correctly. If using IP or cellular, ensure alternate communicator has the
one of the enabled phone numbers. Enter [02] to view correct central station IP and port numbers, as well as APN for cellular.
phone numbers with failure to communicate troubles.
[03] Alternate Comm SIM Lock
SIM lock is enabled and the unit does not have the Replace SIM card with one that does not have a SIM lock pin code programed.
correct SIM PIN.
- 247 -
Trouble [11] Communications Press [11] to determine specific trouble

Check the the event buffer for trouble details.
For radio/SIM failure, ensure the cellular plug-in module is connected to the panel
[04] Alternate Comm Cellular
properly and that the SIM card is correctly inserted in the right orientation.
The alternate communicator has detected a radio or SIM
For Cellular Network trouble ensure the correct Cellular APN is programmed and that
failure, a cellular network trouble, or insufficient signal
the SIM card is activated.
strength.
For insufficient signal strength, sure the antenna is properly connected and the unit is
mounted in a location which allows for a strong signal to the nearest cellular tower.
Check with the ISP to confirm Internet service is active in the area.
Ensure the Ethernet cable is securely inserted into the RJ45 jack of the communicator
and the hub/router/switch.
[05] Alternate Comm Ethernet Check the link light on the hub/router/switch is ON. If link light is OFF, start the
The alternate communicator has detected a network hub/router/switch.
absent condition. If DHCP is used, ensure that the unit has an assigned IP address from the server. In
Section [851] [992] verify a valid IP address is programmed. If not, contact the network
administrator.
If problem persists, replace the Ethernet cable and RJ45 connector
Ensure that the Ethernet path has Internet connectivity.
If using a static IP address, confirm that the gateway and subnet mask are entered
correctly.
[06] Receiver 1-4 Trouble If the network has a firewall, ensure the network has the programmed outgoing ports
open (default UDP port 3060 and port 3065).
Alternate communicator is failing to initialize to the
receiver. Ensure that all cellular receiver APNs have been programmed with the access point
name provided by the cellular provider.
If Common Mode is used, and only one path is initiliazed while the other path is not
successful, generate a manual test transmission over both paths or power cycle the
communicator to recover the "Receiver Not Available" trouble.
[07] Receiver 1-4 Supervision This trouble is indicated when supervision is enabled and the unit is not able to
The alarm system loses communication with an Ethernet successfully communicate with the receiver.
or cellular receiver on the system. If this trouble persists, contact the central station.
[09] Alternate Comm Fault Check section [382] toggle option[5] is ON if using an Alarm.com alternate
The alternate communicator has not responded to any communicator. If not, it should be OFF.
poll commands. Alt Comm Fault is displayed in [*][2] and Ensure the PC-LINK cable between the panel and Alarm.com communicator is
the event buffer. connected properly (not reversed) and is securely in place.
The unit has exhausted all communications attempts to all programmed receivers for
[10] Alternate Comm FTC Fault events generated by the communicator.
Restart the system and if trouble persists, contact the dealer.
Trouble [12] Not Networked Press [12] to toggle through troubles
[01] Zones 1-248
Ensure the device is physically present.
[02] keypad 1-16
Check the current signal strength and during the last 24 hours.
[03] Siren 1-16
Replace the battery or press the tamper switch.
[04] Repeater 1-8
Enroll the device again.
[05] User 1-32
If wireless devices were recently enrolled, or the HSM2HOST was power cycled, wait
A device is out of sync with the wireless network or was up to 16 minutes for the device to synchronize to the network.
not synchronized with the network after enrollment.
- 248 -
Trouble [13] AUX Trouble Press [13] to toggle through troubles
[05] HSM2300
[06] HSM2204
[07] System area
Check for a short between Aux+ and Aux- or other system ground.
[10] HSM3408
Ensure the aux current draw has not exceeded the documented limits.
[11] HSM3204CX
Ensure voltage between AUX+ and AUx - is between 9VDC to 14VDC.
[12] HSM3350 AUX 1 trouble
[13] HSM3350 AUX 2 trouble
An auxiliary power supply trouble is present.
Trouble [14] Module Tamper Press [14] to determine specific trouble
Check the Alarm.com communicator firmware is compatible with PSP firmware to
support extended number of Zones and Partitions.
Interactive Zone trouble is generated when the Alarm.com firmware does not support
[01] Interactive Zone the configured number of zones in panel (>220 Zones) and Interactive Partition
[02] Interactive Partition Trouble is generated when the Alarm.com firmware does not support configured
number of Partitions.
Ensure to configure compatible number of zones and partitions while using with
Alarm.com.
IMPORTANT!
Ensure you have the following information available before contacting Customer Support :
Alarm controller type and version, (e.g., HSM3032 V1.1):
Note: Version number can be accessed by entering [*][Installer Code][900] on any LCD keypad. This information is also loc-
ated on a sticker on the printed circuit board.
List of modules connected to control panel, (e.g., HSM2108, HSM2HOSTx etc.) .
- 249 -
Appendix 1: Reporting codes

The following tables contain Contact ID and Automatic SIA format reporting codes. See "[308] Event Reporting" on page 116
for event reporting codes.
Contact ID
Each of the digits indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the event code
contains [34]. The central station would receive the following:
*BURG - ENTRY/EXIT - 1 where the “1” indicates which zone went into alarm.
See "Contact ID and SIA Zone Alarm/Restore Event Codes" on page 250 for code definitions.
SIA Format - Level 2 (Hard Coded)
The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Stand-
ard - October 1997. This format sends the account code along with its data transmission. The transmission appears similar to
the following at the receiver:
N ri1 BA 01
N = New Event
ri1 = Partition /Area Identifier
BA = Burglary Alarm
01 = Zone 1
A system event uses the Area Identifier ri00.
Contact ID and SIA Zone Alarm/Restore Event Codes
Dialer Automatic Contact ID
Section # Definition SIA Auto Rep Codes**
Direction* Codes
Zone Events
[307] Zone Alarms A/R see "Contact ID & SIA Zone Alarm/Restore Event Codes" on
[307] Zone Restores A/R page 255" for details.
[307] Zone tamper/restore MA/R E(3)83-ZZZ / R(3)83-ZZZ TA-ZZZ / TR-ZZZZ

[307] Zone fault/restore MA/R E(3)8A-ZZZ / R(3)8A-ZZZ UT-ZZZZ / UJ-ZZZZ
Tamper Events
E(3)83-(601 -616) TA-(0601-0616)
[308]-[101] Keypad 1-16 tamper/restore alarm T/R
R(3)83-(601 -616) TR-(0601-0616)
E (3)83-(801-816) TA-(0801-0816)
[308]-[101] Siren 1-16 tamper/restore alarm T/R
R (3)83-(801-816) TR-(0801-0816)
E(3)83-(901-908) TA-(0901-0908)
[308]-[101] Repeater 1-8 tamper/restore alarm T/R
R (3)83-(901-908) TR-(0901-0908)
E(3)41-(101-130) ES-(0101-0130)
[308]-[101] HSM2108: 8-Zone Expander module #1-30 tamper/restored T/R
R(3)41-(101-130) EJ-(0101-0130)
E(3)41-(201-216) ES-(0201-0216)
[308]-[101] HSM2208: 8-Output Expander module #1-16 tamper/restored T/R
R(3)41-(201-216) EJ-(0201-0216)
HSM2204: Power Supply-1A (4 high-current outputs) #1-4 E(3)41-(601-604) ES-(0601-0604)

[308]-[101] T/R
tamper/restored R(3)41-(601-604) EJ-(0601-0604)
E(3)41-(621-624) ES-(0621-0624)
[308]-[101] HSM2300: Power Supply module #1-4 tamper/restored T/R
R(3)41-(621-624) EJ-(0621-0624)
E(3)41-553 ES-0553
[308]-[101] HSM2955: Audio module tamper/restore T/R
R(3)41-553 EJ-0553
E(3)41-(301-330) ES-(0301-0330)
[308]-[101] HSM3408: 8 I/O Expansion module #1-30 tamper/restored T/R
R(3)41-(301-330) EJ-(0301-0330)
E(3)41-(801-808) ES-(0801-0808)
[308]-[101] HSM3204CX: Corbus repeater module #1-8 tamper/restored T/R
R(3)41-(801-808) EJ-(0801-0808)
- 250 -

Direction* Codes
E(3)41-(651-654) ES-(0651-0654)
[308]-[101] HSM3350: 3A Power supply module #1-4 tamper/restored T/R
R(3)41-(651-654) EJ-(0651-0654)
[308]-[101] Keypad Lockout - Incorrect access code entry T/R E(4)61-000 JA-0000
Opening Events
[308]-[201] User Openings - Disarmed by user O/C E(4)A1-UUU OP-UUUU
[308]-[202] Automatic Arming Canceled O/C E(4)64-UUU CI-0000
Special Opening - System disarmed using: keyswitch,
[308]-[201] O/C E(4)AA-000 OP-0000
maintenance code, DLS software, wireless key
Late to Open - System not disarmed before late to open time
[308]-[211] O/C E(4)53-000 CT-0000
expired
[308]-[202] Automatic (Schedule) Opening O/C E(4)A3-000 OA-0000
[308]-[201] Keyswitch Open O/C E(4)A9-ZZZ OS-ZZZZ
Closing Events
[308]-[201] User Closings - System armed by user, wireless key O/C R(4)A1-UUU CL-UUUU
[308]-[221] Partial Closing - 1 or more zones bypassed when armed O/C E(4)56-000 CG-0000
Special Closing - System armed via: quick arm, keyswitch,
[308]-[201] O/C R(4)AA-000 CL-0000
function key, maintenance code, DLS software
[308]-[211] Late to Close - Auto-arm prealert sounded O/C E(4)54-000 CI-0000
[308]-[211] Exit Fault O/C E(3)74-ZZZ EA-ZZZZ
[308]-[202] Automatic (Schedule) Closing O/C R (4)A3-000 CA-0000
[308]-[201] Keyswitch Close O/C R(4)A9-ZZZ CS-ZZZZ
System Trouble Events

[308]-[301] Battery trouble/restore - Main panel MA/R E(3)A2-000 / R(3)A2-000 YT-0000 / YR-0000
[308]-[301] Battery absent trouble/restore - Main panel MA/R E(3)11-000 / R(3)11-000 YM-0000 / YR-0000
[308]-[301] Power unit failure trouble/restore MA/R E(3)14-000 / R(3)14-000 YP-0000 / YQ-0000
[308]-[301] Panel AC trouble/restore - Main panel MA/R E(3)A1-000 / R(3)A1-000 AT-0000 / AR-0000
[308]-[302] Bell circuit trouble/restore MA/R E(3)21-000 / R(3)21-000 YA-9999 / YH-9999
[308]-[302] TLM (telephone line) fail/restore MA/R E(3)51-000 / R(3) 51-000 LT-0001 / LR-0001
[308]-[302] Auxiliary power trouble/restore MA/R E(3) 12-000 / R(3) 12-000 YP-0000 / YQ-0000
[308]-[302] Corbus output fault/restore MA/R E(3)12-000 / R(3)12-000 YP-0000 / YQ-0000
[308]-[302] Panel overcurrent trouble/restore MA/R E(3)12-000 / R(3)12-000 YI-0000 / YJ-0000
[308]-[305] PGM 2, 2-Wire smoke trouble/restore MA/R E(3)73-992 / R(3)73-992 FT-0992 / FJ-0992
Module Troubles
E(3)AA-001-016 EM-0001-0016
[308]-[332] Hardwired Module Low Voltage trouble/restore - Keypads MA/R
R(3)AA-001-016 EN-0001-0016
E (3)AA-101-130 EM-0101-0130
[308]-[332] Hardwired Module Low Voltage trouble/restore - HSM2108 MA/R
R (3)AA-101-130 EN-0101-0130
E(3)AA-201-216 EM-0201-0216
R(3)AA-201-216 EN-0201-0216
E (3)AA-551 EM-0551
[308]-[332] Hardwired Module Low Voltage trouble/restore - HSM2HOST MA/R
R (3)AA-551 EN-0551
E(3)AA-601-604 EM-0601-0601
R(3)AA-601-604 EN-0601-0604
E (3)AA-621-624 EM-0621-0624
R (3)AA-621-624 EN-0621-0624
- 251 -

Direction* Codes
E(3)AA-553 EM-0553
R(3)AA-553 EN-0553
E(3)3A-001-016 ET-0001-0032
[308]-[332] Hardwired Module Supervisory trouble/restore - Keypads MA/R
R(3)3A-001-016 ER-0001-0032
E (3)3A-101-130 ET-0101-0162
[308]-[332] Hardwired Module Supervisory trouble/restore - HSM2108 MA/R
R (3)3A-101-130 ER-0101-0162
E(3)3A-201-216 ET-0201-0216
R(3)3A-201-216 ER-0201-0216
E(3)3A-551 ET-0551
[308]-[332] Hardwired Module Supervisory trouble/restore - HSM2HOST MA/R
R(3)3A-551 ER-0551
E (3)3A-601-604 ET-0601-0601
R (3)3A-601-604 ER-0601-0604
E(3)3A-621-624 ET-0621-0624
R(3)3A-621-624 ER-0621-0624
E(3)3A-553 ET-0553
R(3)3A-553 ER-0553
E(3)12-601-604 YI-0601-604
[308]-[332] HSM2204 Aux Supply 1-4 trouble/restore MA/R
R(3)12-601-604 YJ-0601-0604
E(3)12-621-624 YI-0621-624
R(3)12-621-624 YJ-0621-624
E(3)12-301-330 YI-0301-0330
R(3)12-301-330 YJ-0301-0330
E(3)12-801-808 YI-0801-0808
[308]-[332] HSM3204CX Aux Supply 1-8 trouble/restore MA/R
R(3)12-801-808 YJ-0801-0808
E(3)12-801-808 YI-0801-0808
[308]-[332] HSM3204CX: Corbus output 1-8 trouble/restore MA/R
R(3)12-801-808 YJ-0801-0808
E(3)12-651-654 YI-0651-0654
R(3)12-651-654 YJ-0651-0654
E(3)A2-601-604 YT-0601-0604
[308]-[331] HSM2204 1-4 Low Battery trouble/restore MA/R
R(3)A2-601-604 YR-0601-0604
E(3)A2-621-624 YT-0621-0624
R(3)A2-621-624 YR-0621-0624
E(3)A2-801-808 YT-0801-0808
[308]-[331] HSM3204CX 1-8 Low Battery trouble/restore MA/R
R(3)A2-801-808 YR-0802-0808
E(3)A2-651-654 YT-0651-0654
R(3)A2-651-654 YR-0651-0654
E(3)11-601-604 YM-0601-0604
[308]-[331] HSM2204 1-4 Battery absent trouble/restore MA/R
R(3)11-601-604 YR-0601-0604
E(3)11-621-624 YM-0621-0624
[308]-[331] HSM2300 1-4 Battery absent trouble/restore MA/R
R(3)11-621-624 YJ-0621-0624
E(3)11-801-808 YM-0801-0808
[308]-[331] HSM3204CX 1-8 Battery 1 or 2 absent /restore MA/R
R(3)11-801-808 YR-0801-0808
E(3)11-651-654 YM-0651-0654
[308]-[331] HSM3350 1-4 Battery absent /restore MA/R
R(3)11-651-654 YR-0651-0654
E(3)14-801-808 YP-0801-0808
[308]-[331] HSM3204CX 1-8 Power unit failure/restore MA/R
R(3)14-801-808 YQ-0801-0808
- 252 -

Direction* Codes
E(3)14-651-654 YP-0651-0654
[308]-[331] HSM3350 1-4 Power unit failure/restore MA/R
R(3)14-651-654 YQ-0651-0654
E(3)A1-801-808 AT-0801-0808
[308]-[331] HSM3204CX 1-8 AC failure /restore MA/R
R(3)A1-801-808 AR-0801-0808
E(3)A1-651-654 AT-0651-0654
[308]-[331] HSM3350 1-4 AC failure /restore MA/R
R(3)A1-651-654 AR-0651-0654
Alternate Communicator
E(3)3A-000
[308]-[351] Alternate Communicator fault/restore MA/R ET-0000 / ER-0000
R(3)3A-000
E(3)AA-001
[308]-[351] Alternate Communicator Radio/SIM failure/restore MA/R YX-0001 / YZ-0001
R(3)AA-001
E(3)AA-001
[308]-[351] Alternate Communicator cellular trouble/restore MA/R YX-0001 / YZ-0001
R(3)AA-001
E(3)AA-001
[308]-[352] Alternate Communicator Ethernet trouble/restore MA/R YX-0001 / YZ-0001
R(3)AA-001
E(3)5A-001-004 YS-0001-0004
[308]-[354] Alternate Communicator Receiver 1-4 absent/restore MA/R
R(3)5A-001-004 YK-0001-0004
Alternate Communicator Receiver 1-4 Supervisory E(3)5A-001-004 YS-0001-0004

[308]-[355] MA/R
trouble/restore R(3)5A-001-004 YK-0001-0004
E(3)AA-001
[308]-[353] Alternate Communicator SMS Config trouble/restore MA/R YX-0001 / YZ-0001
R(3)AA-001
[308]-[351] Receiver X FTC Restoral MA/R R(3)54-00X YK-000X
On-Board Communicator
[851][025] Radio activation restore N/A R(5)52-001 RS-0001
[851][226] Ethernet Receiver 1 Test Transmission N/A E(6)A3-951 RP-0001
[851][227] Ethernet Receiver 2 Test Transmission N/A E(6)A3-952 RP-0002
[851][228] Cellular Receiver 3 Test Transmission N/A E(6)A3-955 RP-0003
[851][229] Cellular Receiver 4 Test Transmission N/A E(6)A3-956 RP-0004
[851][230] Alternate Communicator FTC Restore N/A R(3)54-001 YK-0001
Wireless Events
Wireless Zone Low Battery trouble/restore E(3)84-ZZZ XT-ZZZZ
[308]-[361] MA/R
ZZZ= Wireless zones 001-248. R(3)84-ZZZ XR-ZZZZ
Wireless Device Low Battery trouble/restore.
ZZZ= 601-616: wireless keypads E(3)84-ZZZ XT-ZZZZ
[308]-[361] 701-732: wireless keys MA/R
801-816: wireless Sirens R(3)84-ZZZ XR-ZZZZ
901-908: wireless repeaters
E(3)A1-ZZZ AT-ZZZZ
[308]-[361] Wireless Zone AC trouble/restore MA/R
R(3)A1-ZZZ AR-ZZZZ
E(3)8A-ZZZ UT-ZZZZ
[308]-[361] Wireless Device Fault/restore MA/R
R(3)8A-ZZZ UJ-ZZZZ
E(3)8A-ZZZ KT-ZZZZ
[308]-[361] Wireless Temperature and Flood Probe trouble/restore MA/R
R(3)8A-ZZZ KJ-ZZZZ
E(3)8A-ZZZ
[308]-[361] Freeze trouble/restore MA/R ZT/ZJ-ZZZZ
R(3)8A-ZZZ
Self Test Trouble/Restore*
E (3)89-ZZZ
[308]-[361] Note: To prevent a reporting code conflict do not program MA/R YX/YZ-ZZZZ
R (3)89-ZZZ
PG9984 as zone 1.
- 253 -

Direction* Codes
E(3)8A-ZZZ AT-(0901-0908)
[308]-[361] Carbon monoxide trouble/restore MA/R
R(3)8A-ZZZ AR-(0901-0908)
E(3)A1-(901-908)
[308]-[361] Wireless repeater 1-8 AC fail/restore MA/R UT/UJ-ZZZZ
R(3)A1-(901-908)
E(3)44-000 XQ-0000
[308]-[361] RF jam/restore MA/R
R(3)44-000 XH-0000
E(3)44-(901-908) XQ-(0901-0908)
[308]-[361] Wireless repeater 1-8 RF jam/restore MA/R
R(3)44-(901-908) XH-(0901-0908)
Miscellaneous Alarms
[308]-[001] Duress Alarm - Code entered at keypad A/R E(1)21-000 HA-0000
[308]-[001] Opening After Alarm - Disarmed with alarm in memory A/R E(4)58-000 OR-0000
Recent Closing - Alarm occurs within two minutes of system
[308]-[001] A/R E(4)59-UUU CR-UUUU
arming
[308]-[001] Burglary Verified A/R E(1)39-000 BV-0000
[308]-[001] Burglary Not Verified A/R E(3)78-000 BG-0000
E(1)43-000
[308]-[001] HSM2108 Zone Expander Supervisory Alarm/restore A/R UA-0000 / UH-0000
R(1)43-000
[308]-[002] Holdup Verified A/R E(1)29-000 HV-0000
[308]-[011] Alarm Canceled before expiry of alarm cancellation timer A/R E(4)A6-UUU OC-UUUU
E(1)46-992
[308]-[011] PGM2 (Silent 24 Hour Input) -Aux Input Alarm/restore A/R UA-0992 / UH-0992
R(1)46-992
E(1)4A-992
[308]-[011] PGM2 (Audible 24 Hour Input) -Aux Input Alarm/restore A/R UA-0992 / UH-0992
R(1)4A-992
E(1)11-992
[308]-[305] PGM2 2-Wire Smoke Alarm/Restore A/R FA-0992 / FH-0992
R(1)11-992
Priority Alarm and Restoral Events

E(1)1A-000
[308]-[011] [F] Key alarm/restore A/R FA-0000 / FH-0000
R(1)1A-000
E(1)AA-000
[308]-[011] [M] Key alarm/restore A/R MA-0000 / MH-0000
R(1)AA-000
E(1)2A-000
[308]-[011] [P] Key alarm/restore A/R PA-0000 / PH-0000
R(1)2A-000
E(1)1A-000
[308]-[011] Wireless key fire alarm/restore A/R FA-0000 / FH-0000
R(1)1A-000
E(1)AA-000
[308]-[011] Wireless key medical alarm/restore A/R MA-0000 / MH-0000
R(1)AA-000
E(1)2A-000
[308]-[011] Wireless key panic alarm/restore A/R PA-0000 / PH-0000
R(1)2A-000
E(1)1A-000
[308]-[011] Interactive fire alarm/restore A/R FA-0000 / FH-0000
R(1)1A-000
E(1)AA-000
[308]-[011] Interactive medical alarm/restore A/R MA-0000 / MH-0000
R(1)AA-000
E(1)2A-000
[308]-[011] Interactive panic alarm/restore A/R PA-0000 / PH-0000
R(1)2A-000
Miscellaneous Closing
[308]-[221] Zone Bypass at time of arming O/C E(5)7A-ZZZ UB-ZZZZ
[308]-[221] Zone Unbypass O/C R(5)7A-ZZZ UU-ZZZZ
- 254 -

Direction* Codes
Testing
E(6)A7-UUU
[308]-[401] Walk Test Begin/End T TS-UUUU/TE-UUUU
R(6)A7-UUU
[308]-[401] Periodic Test T E(6)A2-000 RP-0000
[308]-[401] Periodic Test with Trouble T E(6)A8-000 RY-0000
[308]-[401] System Test - [*][6] bell/communications test T E(6)A1-000 RX-0000
Maintenance
E(3)73-ZZZ
[308]-[311] Fire trouble/restore MA/R FT-ZZZZ / FJ-ZZZZ
R(3)73-ZZZ
E(3)8A-ZZZ
[308]-[314] Gas trouble/restore MA/R GT-ZZZZ / GJ-ZZZZ
R(3)8A-ZZZ
E(3)8A-ZZZ
[308]-[314] Heat trouble/restore MA/R KT-ZZZZ / KJ-ZZZZ
R(3)8A-ZZZ
[308]-[311] Cold Start - System has restarted after total power loss MA/R R(3) A5-000 RR-0000
[308]-[312] Event Buffer 75% Full MA/R E(6)22-000 JL-0000
[308]-[312] DLS Lead In - Download session start MA/R E(4)11-000 RB-0000
[308]-[312] DLS Lead Out - Download session stop MA/R E(4)12-000 RS-0000
[308]-[312] SA Lead In - Download session start MA/R E(4)11-000 RB-0000
[308]-[312] SA Lead Out - Download session stop MA/R E(4)12-000 RS-0000
[308]-[312] Installer Lead In - Installer Programming has been entered MA/R E(6)27-000 LB-0000
[308]-[312] Installer Lead out - Installer Programming has been exited MA/R E(6)28-000 LS-0000
E(9)01-900
[308]-[313] Panel firmware update begin/ successful MA/R LB-0900 / LS-0900
R(9)01-900
[308]-[313] Panel firmware update fail MA/R E(9)02-900 LU-0900
E(3)14-000 YP-000
[308]-[321] Panel power unit fail/restore MA/R
R(3)14-000 YQ-000
*
A/R = alarms/restores; T/R = tampers/restorers; O/C = openings/closings; MA/R = maintenance alarms/restores; T = test transmissions
**
UUU = user number (user 001-1000). Note that for CID, enter 999 for user 1000. ZZZ/ZZZZ = zone number (001-248).
***
Zones and panic pendants are identified, wireless keys can be identified for openings and closings.
Contact ID & SIA Zone Alarm/Restore Event Codes

(as per SIA DCS: ‘Contact ID’ 01-1999):
The table below defines the meaning of all Contact ID and SIA zone alarm/restore event codes.
Zone Definition SIA Auto Rep Codes Contact ID Auto Rep Codes
Delay 1 BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Delay 2 BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Instant BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Interior BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Interior Stay/Away BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Delay Stay/Away BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Instant Stay/Away BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Interior Delay BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Day Zone BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
- 255 -
Zone Definition SIA Auto Rep Codes Contact ID Auto Rep Codes
Night Zone BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
24-Hr. Burglary BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Delayed 24-Hr. Fire (Wireless) FA-ZZZZ / FH-ZZZZ E(1) 1A - ZZZ / R(1)1A - ZZZ
Standard 24-Hr. Fire (Wireless) FA-ZZZZ / FH-ZZZZ E(1) 1A - ZZZ / R(1)1A - ZZZ
24-Hr. Sprinkler SA-ZZZZ / SH-ZZZZ E(1) 13 - ZZZ / R(1)13 - ZZZ
24-Hr.Low Temperature ZA-ZZZZ / ZH-ZZZZ E(1) 59 - ZZZ / R(1)59-ZZZ
24-Hr High Temperature KA-ZZZZ / KH-ZZZZ E(1) 58 - ZZZ / R(1)58 - ZZZ
24-Hr. Latching Tamper BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
24-Hr. Non Alarm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
24-Hr. Non-latching Tamper TA-ZZZZ / TR-ZZZZ E(3) 83 - ZZZ / R(3)83 - ZZZ
24-Hr. Masking Trouble UT-ZZZZ / UJ-ZZZZ E(3) 8A - ZZZ / R38A-ZZZ
Momentary Keyswitch Arm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Maintained Keyswitch Arm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Momentary Keyswitch Disarm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
Maintained Keyswitch Disarm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ
24-Hr. Supervisory US-ZZZZ / UR-ZZZZ E(1) 5A - ZZZ / R(1)5A - ZZZ
24-Hr. Supervisory Buzzer UA-ZZZZ / UH-ZZZZ E(1) 5A - ZZZ / R(1)5A - ZZZ
24-Hr. Auto Verified Fire (Wireless) FA-ZZZZ / FH-ZZZZ E(1) 1A - ZZZ / R(1)1A - ZZZ
Fire Supervisory FS-ZZZZ / FV-ZZZZ E(2) AA - ZZZ / R(2)AA - ZZZ
24-Hr. Gas GA-ZZZZ / GH-ZZZZ E(1) 51 - ZZZ / R(1)51 - ZZZ
24-Hr. CO Alarm GA-ZZZZ / GH-ZZZZ E(1) 62 - ZZZ / R(1)62 - ZZZ
24-Hr. Holdup HA-ZZZZ / HH-ZZZZ E(1) 22 - ZZZ / R(1)22 - ZZZ
24-Hr. Panic PA-ZZZZ / PH-ZZZZ E(1) 2A - ZZZ / R(1)2A - ZZZ
24-Hr. Flood WA-ZZZZ / WH-ZZZZ E(1) 54 - ZZZ / R(1)54 - ZZZ
24-Hr Heat KA-ZZZZ / KH-ZZZZ E(1) 58 - ZZZ / R(1)58 - ZZZ
24-Hr. Medical MA-ZZZZ / MH-ZZZZ E(1) AA - ZZZ / R(1)AA - ZZZ
24-Hr. Emergency QA-ZZZZ / QH-ZZZZ E(1) A1 - ZZZ / R(1)A1 - ZZZ
Push to Set (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A - ZZZ
Final Door Set BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A - ZZZ
ZZZ/ZZZZ = zones 001-248
- 256 -
Appendix 2: Word library
Appendix 2: Word library

001 Aborted 002 AC 003 Access 004 Active 005 Activity 006 Alarm
007 All 008 AM 009 Area 010 Arm 011 Armed 012 Arming
013 Attic 014 Auxiliary 015 Away 016 Baby 017 Back 018 Bar
019 Basement 020 Bathroom 021 Battery 022 Bedroom 023 Bonus 024 Bottom
025 Breezeway 026 Building 027 Bus 028 Bypass 029 Bypassed 030 Cabinet
031 Camera 032 Canceled 033 Car 034 Carbon 035 Central 036 Chime
037 Closed 038 Closet 039 Closing 040 Code 041 Communicator 042 Computer
043 Control 044 Date 045 Daughter’s 046 Degrees 047 Delay 048 Den
049 Desk 050 Detector 051 Dining 052 Disarmed 053 Door 054 Down
055 Download 056 Downstairs 057 Drawer 058 Driveway 059 Duct 060 Duress
061 East 062 Energy 063 Enter 064 Entry 065 Error 066 Exercise
067 Exit 068 Exterior 069 Factory 070 Failure 071 Family 072 Father’s
073 Feature 074 Fence 075 Fire 076 First 077 Floor 078 Force
079 Foyer 080 Freeze 081 Front 082 Furnace 083 Gallery 084 Garage
085 Gas 086 Glass 087 Goodbye 088 Gym 089 Hallway 090 Heat
091 Hello 092 Help 093 High 094 Home 095 House 096 In
097 Install 098 Interior 099 Intrusion 100 Invalid 101 Is 102 Key
103 Kids 104 Kitchen 105 Latchkey 106 Laundry 107 Left 108 Level
109 Library 110 Light 111 Lights 112 Living 113 Load 114 Loading
115 Low 116 Lower 117 Main 118 Master 119 Mat 120 Medical
121 Memory 122 Menu 123 Monoxide 124 Mother’s 125 Motion 126 No
127 North 128 Not 129 Now 130 Number 131 Off 132 Office
133 OK 134 On 135 Open 136 Opening 137 Panic 138 Partition
139 Patio 140 Pet 141 Phone 142 Please 143 PM 144 Police
145 Pool 146 Porch 147 Power 148 Press 149 Program 150 Progress
151 Quiet 152 Rear 153 Receiver 154 Report 155 RF 156 Right
157 Room 158 Safe 159 Saver 160 Schedule 161 Screen 162 Second
163 Sensor 164 Service 165 Shed 166 Shock 167 Shop 168 Side
169 Siren 170 Sliding 171 Smoke 172 Son’s 173 Sound 174 South
175 Special 176 Stairs 177 Stay 178 Sun 179 Supervisory 180 System
181 Tamper 182 Temperature 183 Test 184 Time 185 To 186 Touchpad
187 Trouble 188 Unbypass 189 Unit 190 Up 191 West 192 Window
193 Zone 194 000 195 001 196 002 197 003 198 004
199 005 200 006 201 7 202 8 203 9 204 A
205 B 206 C 207 D 208 E 209 F 210 G
211 H 212 I 213 J 214 K 215 L 216 M
217 N 218 O 219 P 220 Q 221 R 222 S
223 T 224 U 225 V 226 W 227 X 228 Y
229 Z 230 (Space) 231 ‘ (Apostrophe 232 - (Dash) 233 _(Underscore) 234 *
235 # 236 : 237 / 238 ? 239 240
- 257 -
Appendix 3: Template programming tables

The following tables show the programming options for template programming digits 1-5.
Digit 1 – Zones 1-8 Definition Options
Note: A “0” in the digit 1 location indicates that the first 8 zones use the panel default zone definitions.
Option Zn1 Zn2 Zn3 Zn4 Zn5 Zn6 Zn7 Zn8 Zone Definitions (Options 1- 6)
1 001 003 003 003 004 004 004 004 001 Delay 1
2 001 003 003 005 005 005 005 008 003 Instant
3 001 003 003 005 005 005 005 007 004 Interior
4 001 001 003 003 003 003 003 003 005 Interior Stay/Away
5 001 003 003 006 005 005 005 005 006 Delayed Stay/Away
6 001 003 003 006 005 005 005 008 007 Delayed 24Hr. Fire
7 (ADT) 001 001 006 006 006 001 001 001 008 Standard 24Hr. Fire (Wireless)
Refer to "[001] Zone types" on page 78 for details.
Digit 2 – System EOL Configuration Options

Option [13] bit 1 [13] bit 2
1 NC Loops ON OFF
2 SEOL OFF OFF
3 DEOL OFF ON
Digit 3 – Reporting Code Communication Options

Entry Template Programming
1 Disabled [380] Comm Toggles 1 - Bit 1 Communications Enabled - Off
[380] Comm Toggles 1 - Bit 1 Communications Enabled - On
[350] Communicator Formats - [001] Receiver 1 - 04 SIA
[381] Comm Toggles 2 - Bit 2 Bell Ringback - Off
2 Receiver 1 and 2 SIA with Backup [384] Comm Backup - Bit 2 Receiver 2 Backup - On
[384] Comm Backup - Bit 2 Receiver 2 Backup - Off
[300] Comm Path - [001] Receiver 1 - 01 PSTN
- 258 -

[350] Communicator Formats - [001] Receiver 1 - 03 CID
[384] Comm Backup - Bit 2 Receiver 2 Backup - On
3 Receiver 1 SIA, Receiver 2 CID with backup
[381] Comm Toggles 2 - Bit 2 Bell Ringback - Off
4 Receiver 1 SIA [384] Comm Backup - Bit 2 Receiver 2 Backup - Off
- 259 -

5 Receiver 1 CID
[384] Comm Backup - Bit 2 Receiver 2 Backup - On
6 Receiver 1 and 2 CIA with backup
Digit 4 – Reporting Code Configuration Options

Option Common Group Selected Troubles Openings/ Closings Zone Alarm Restore DLS/Installer Lead In/Out
1 ü ü X
2 ü ü ü X
3 ü ü ü X
4 ü ü ü ü X
5 ü ü X
6 ü ü X
7 ü ü ü X
8 ü
ü indicates included, blank indicates default setting, X indicates disabled
- 260 -
Common Group
Common Group Common Group Programming
Set all reporting codes to automatic [308] Event Reporting - All Events On
[311][001] Partition 1 Alarm/Restore - Bit 1 Receiver 1 - On
[311][001] Partition 1 Alarm/Restore - Bit 2 Receiver 2 - Off
Alarm/restore call directions enabled
[311][002] Partition 1 Tamper/Restore - Bit 1 Receiver 1 - Off
Tamper/restore call directions disabled
[311][003] Partition 1 Open/Close - Bit 1 Receiver 1 - Off
Opening/closing call directions disabled
[309][001] Maintenance - Bit 1 Receiver 1 - On
[309][001] Maintenance - Bit 2 Receiver 2 - Off
Maintenance call directions enabled
[309][002] Test Transmission - Bit 1 Receiver 1 - Off
Test transmission call directions disabled
l Enables/Disables all Reporting Codes

l Selected Troubles - Enables the following Troubles
Selected Troubles Group Selected Troubles Programming
[308][301] - Bit 3 Panel Low Battery - On
[308][301] - Bit 4 Panel Low Battery Restore - On
[308][301] - Bit 5 Panel Battery Absent - On
[308][301] - Bit 6 Panel Battery Absent Restore - On
Battery
[308][331] - Bit 3 Module Low Battery - On
[308][331] - Bit 4 Module Low Battery Restore - On
[308][331] - Bit 5 Module Battery Absent - On
[308][331] - Bit 6 Module Battery Absent Restore - On
[308][301] - Bit 1 Panel AC Trouble - Off
[308][301] - Bit 2 Panel AC Trouble Restore - Off
AC Failure
[308][331] - Bit 1 Module AC Trouble - Off
[308][331] - Bit 2 Module AC Trouble Restore - Off
[308][302] - Bit 1 Panel Bell Trouble - On
Bell Circuit Trouble
[308][302] - Bit 2 Panel Bell Trouble Restore - On
[308][311] - Bit 3 Fire Trouble - On
[308][311] - Bit 4 Fire Trouble Restore - On
Fire, Alarm
[308][305] - Bit 3 2W Smoke Trouble - On
[308][305] - Bit 4 2W Smoke Trouble Restore - On
- 261 -
[308][302] - Bit 5 Panel AUX Trouble - On

[308][302] - Bit 6 Panel AUX Trouble Restore - On
Aux Power Supply Trouble
[308][332] - Bit 5 Module AUX Trouble - On
[308][332] - Bit 6 Module AUX Trouble Restore - On
[308][302] - Bit 3 Panel TLM Trouble - Off
TLM Trouble
[308][302] - Bit 4 Panel TLM Trouble Restore - On
[308][101] - Bit 3 Module Tamper Trouble - Off
General System Tamper
[308][101] - Bit 4 Module Tamper Restore - Off
[308][332] - Bit 3 Module Supervisory Trouble - On
General System Supervisory
[308][332] - Bit 4 Module Supervisory Restore - On
l Openings & Closings - Sets Residential Dial Reporting Codes for all openings and closings
Openings/Closings Group Openings/Closings Programming
[308][201] - Bit 1 User Closing - On
[308][201] - Bit 2 User Opening - On
[308][201] - Bit 5 Special Closing - On
Enable All User Open/Close Reports [308][201] - Bit 6 Special Opening - On
[308][202] - Bit 1 Automatic Closing - On
[308][202] - Bit 2 Automatic Opening - On
[308][202] - Bit 3 Automatic Cancel - On
l Zone Alarm Restore Group - Disables all zone alarm restore reporting codes
Zone Alarm Restore Group DLS/Installer Lead In/Out Programming
[307][001] - Bit 2 Alarm Restore - Off
Restore zone alarm reporting codes [307][005] - Bit 2 Alarm Restore - Off
[307][009] - [128] Bit 2 Alarm Restore - Off
l Installer Lead-in/Lead-out and DLS Lead-in/Lead-out

DLS/Installer Lead In/Out Group DLS/Installer Lead In/Out Programming
[308][312] - Bit 1 Installer Lead In - Off
[308][312] - Bit 2 Installer Lead Out - Off
[308][312] - Bit 3 DLS Lead In - Off
DLS/Installer Disabled
[308][312] - Bit 4 DLS Lead Out - Off
[308][312] - Bit 5 SA Lead In - Off
[308][312] - Bit 6 SA Lead Out - Off
Digit 5 DLS Connection Options

Option Programming Section DLS Connection/Call Back Setting
[401] Option 1 OFF Double Call Disabled
Option 3 OFF Call Back Disabled
1
Option 4 OFF User Initiated Call Up Disabled
[406] 000 Number of Rings to Answer On Disabled
- 262 -
[401] Option 1 ON Double Call Enabled

2
[406] 008 Number of Rings to Answer On is 8
Option 3 ON Call Back Enabled
3
4
Option 4 ON User Initiated Call Up Enabled
After entering a valid 5-digit template programming code, the system prompts for the following data in the sequence listed:
1. Central Station Telephone Number
i. Program the required central station phone number. Press [#] to complete your entry.
ii. This phone number is entered into programming section [301][001].
2. Central Station System Account Code (4 or 6-digit code)
i. Program the system account code. All digits must be entered in order to complete your entry.
ii. This account code is entered into programming section [310][000].
3. Partition 1 Account Code (4 digit code)
i. Program the partition 1 account code. All digits must be entered in order to complete your entry.
ii. This account code is entered into programming section [310][001].
4. DLS Access Code (6-digit code)
i. Program the required DLS access code. All 6 digits must be entered in order to complete your entry.
ii. This access code is entered into programming section [403].
5. Entry Delay 1 and Exit Delay
i. Enter the 3-digit entry delay 1 (in seconds) followed by the desired 3-digit exit delay (in seconds). These entries affect
all partitions.
ii. All 3 digits must be entered in order to complete each section entry.
iii. These values are entered in programming sections [005][001]-[008] entry 1 and 3 respectively.
6. Installer's Code
i. Enter the 4, 6 or 8-digit installer access code (dependent on section [041]). All digits must be entered in order to com-
plete the section entry.
ii. This code is entered into programming section [006][001].
iii. After the installer code has been programmed the system returns to the base installer programming menu.
iv. All template programming information defaults after performing a hardware or software panel default. The 5-digit tem-
plate programming code is defaulted to 0000000.
Note: Pressing the pound key (#) advances through template programming, accepting what is displayed in these locations,
potentially overwriting desired programming. Depending on the option programmed, restoring the defaults using template
programming may not be possible.
- 263 -
Appendix 4: ASCII characters
Appendix 4: ASCII characters

! “ # $ % & ‘ ( ) * + , - . / 0 1 2 3 4 5 6 7 8
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
9 : ; < = > ? @ A B C D E F G H I J K L M N O P
57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Q R S T U V W X Y Z [ ￥ ] ^ _ ╲ a b c d e f g h
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104

i j k l m n o p q r s t u v w x y z { ‫׀‬ } → ←
105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 160
□ 「」 ֻ ▪ ｦｱｨｩｪｫｶｭｮｼｱｲｩｪｫｶキク
161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184
ケコサシスセソタダツテトナニヌネノハヒフヘホマミ
185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208
ムメモヤユョラリルレロワン゙ ▢ α ä β Ɛ μ σ ρ ϧ ʃ
209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232
⊣ ϳ ｘ ¢ ￡ ñ Ö ｐｑ θ ∞ Ω ϋ Σ π X ｙ千 Ⴌ Ħ ÷
233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253
- 264 -
Appendix 5: Regulatory approvals

5.1 FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use
this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
l Re-orient the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules, and, if the product was approved July 23, 2001 or later, the requirements adopted by the
ACTA. On the side of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence
number (REN) for this equipment. If requested, this number must be provided to the Telephone Company.
HS3032 Product Identifier US:F53AL01AHS3256
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules
and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected
to a compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in
the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products
approved after July 23, 2001, the REN for this product is part of the product identifier that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN
is separately shown on the label.
Incidence of Harm
If this equipment HS3032/HS3128/HS3248 causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment.
If this happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment HS3032/HS3128/HS3248 for repair or warranty information, please contact the facility indicated
below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until
the problem is solved. This equipment is of a type that is not intended to be repaired by the end user.
Tyco Atlanta Distribution Center
2600 West Pointe Dr.
Lithia Springs, GA 30122
Additional Information
- 265 -
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation
commission for information.
Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation, even if other equipment (telephone,
answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be connected to a
properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper
installation is depicted in the figure below. Consult your telephone company or a qualified installer if you have any questions concerning these
instructions or about installing the RJ-31X jack and alarm dialling equipment for you.
5.2 Innovation, Scientific and Economic Development Canada (ISED) State-

ment
NOTICE: This Equipment, HS3032/HS3128/HS3248, meets the applicable ISED Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a
Declaration of Conformity indicating that ISED Canada technical specifications were met. It does not imply that Industry ISED approved the
equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an
indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of
any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed five.
HS3032 Registration number: IC: 160A-HS3256
HS3128 Registration number IC: 160A-HS3256.
HS3248 Registration number IC: 160A-HS3256.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme
d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
5.3 UL/ULC Installations

This product (HS3032/HS3128/HS3248) has been tested and found in compliance with the following standards:
l UL1610 Central-Station Burglar-Alarm Units
l UL365 Police Station Connected Burglar Alarm Units and Systems
l UL1023 Household Burglar-Alarm System Units
l UL985 Household Fire Warning System Units
l UL1635 Digital Alarm Communicator System Units
l UL1637 Home Health Care Signaling Equipment
l ULC-S304-16 Standard for Control Units, Accessories and Receiving Equipment for Intrusion Alarm Systems
l ULC-S559-13 Equipment for Fire Signal Receiving Centers and Systems
l ULC-S545-02 Residential Fire Warning System Control Units
The subscriber control unit shall provide for the connection of protective wiring, conductors, and attachments in accordance with the Standard for Installation and Clas-
sification of Burglar and Holdup Alarm Systems, UL 681.
This product has also been tested and found in compliance with the ANSI/SIA CP-01-2014 Control Panel Standard – Features for False Alarm Reduction.
This product is UL/ULC listed under the following categories:
l AMCX/AMCXC Central Stations Alarm Units
l AOTX Local Alarm Units
l APAW Police-station-connected Alarm Units
l DAYRC Central Station Fire Alarm System Units
l UTOU/UTOUC Control Units and Accessories, Household System Type
l NBSX/NBSXC Household Burglar Alarm System Units
l AMTB Control Panels, SIA False Alarm Reduction
- 266 -
The product is labeled with the UL and ULC listing marks along with the SIA CP-01 compliance statement (Also Classified in accordance with SIA-CP-01 Standard) as
proof of compliance with the above mentioned standards. For further information on this product’s listings please also refer to the official listing guides published at the
UL web site (www.ul.com) under Online Directions Section.
UL/ULC Residential Fire and Burglary Installations:
For ULC Installations, refer to the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540.
l Control Unit must be enclosed in model HSC3010C or HSC3020C enclosure.
l Power supply model SOY-1800360NA (HS65WPSNA) must be employed.
l 24 h standby power must be provided for fire applications and 4h for burglary only applications (AC trouble must be transmitted to SRC).
l One DSC Model RM-1 or RM2 end-of-line supervision relay module must be used.
l Priority of signals needs to be set Fire, CO/ Medical, Burg, Panic, AUX (Flood).
l All burglary-type zones shall be configured with SEOL or DEOL configuration. Use model EOLR-2
l (refer to section [002], bit 10 or 11 shall be ON)
l Use at least one PG9926/ PG9916/ PG9936 Smoke Detector for Fire Installations (section [001], fire zone shall be programmed as type 025)
l The entry delay shall not exceed 45 seconds (see section [005])
l The exit delay shall not exceed 60 seconds (refer to section [005])
l The minimum Bell Time-out is 4 minutes (refer to section [005])
Note: Connect Bell output to a UL/ULC Listed audible device (e.g., UL File S8534, model TS-443S-6), rated to operate over the range of 10.8 to 12.5 VDC and 85dBA
minimum. Wireless sirens PG9901 and PG9911 may also be used as audible devices.
Note: For ULC Residential Fire installations, minimum bell time-out is 5 min. For UL Home Health Care installations, minimum bell time-out is 5 min. For UL Com-
mercial Burglary installations, minimum bell time-out is 15 min.
l Temporal Three Fire Signal shall be enabled (section [013], opt.8 ON)
l Arm/Disarm Bell Squawk shall be enabled when using wireless key PG4939/PG4929/PG4949 (section [014], option 1 shall be ON)
l A code shall be required for bypassing (section [023], option 4 shall be ON)
l Trouble beeps shall be enabled (section [022], option 7 shall be ON)
l AC trouble indication LED shall be enabled (Keypad Programming, section [022], options 5 and 6 shall be ON)
l DACT Communicator shall be enabled for Supervising Station Monitoring (section [380], option 1 shall be ON)
Note: The DACT communicator for this product has no line security.
Telephone Line Monitoring (TLM) shall be enabled (section [015], option 7 shall be ON)
This product is programmed to perform 5 attempts for communication of an event to the supervising station. If unsuccessful, a Fail To Communicate (FTC) trouble is
generated.
Test transmission cycle shall be set (refer to section [351]) for monthly transmission for UL residential burglary applications and to 7 days for UL residential fire applic-
ations.
Note: For ULC Residential/Commercial installations set for daily test transmission.
l For UL Residential Fire installations, [*][2] requires code shall be enabled (Section [023] option 5 ON) and latching troubles shall be enabled (Section [019] option
2 ON)
l If a repeater is needed, two repeaters model PG9920 shall be used to ensure proper signal routing.
l Wireless Supervision window shall be set to 4 hours for Fire Installations (Wireless Programming, section [804]>[802] shall be programmed with the value 16).
l Wireless Supervision window shall be set to 24 hours for Burglary Installations only (Wireless Programming, section [804]>[802] shall be programmed with the
value 96).
l RF Jam detection shall be enabled (refer to Wireless Programming (section [804][801], option 00 shall be OFF).
l New Alarms will Disconnect 2-way Audio (section [022], option 6 OFF).
Requirements for UL985 6th edition compliant installations:
For UL residential fire applications (including CO) compliant with UL985 6th edition, the following guidelines shall be respected:
l Two UL listed compatible keypads (for example HS2LCDPRO, HS2TCHPRO(BLK), HS2LCDRFPRO9) shall be used, each having communication bus wir-
ing directly connected to the RED/BLK/YEL/GRN terminals located on the main control panel board assembly.
l Power loop supervision relay model RM-1(C) or RM-2 shall be connected to AUX power output to report wiring faults if it is used for powering fire/CO detec-
tion devices.
l Section [023] option 5 shall be ON. A user code shall be required to view the [*] [2] trouble menu. When enabled, trouble beeps will only be silenced when the
[*] [2] has been entered and exited.
l In section [377] [003] a test transmission must be sent to the monitoring station every 7 days (default: 007).
l In section [377] [004], the default time is programmed for 4.45 a.m (0445). The panel will generate a random test transmission time within a ± 60 minute win-
dow.
l If a repeater is required, two of the PG9920 models shall be used for proper signal routing.
l Latching troubles shall be enabled (section [019] option 2 must be set to ON).
l In a combination fire and burglary application, fire alarm detection devices shall not be powered from the same AUX output (control panel, zone expander,
power supply) as burglary alarm initiating devices.
l Power supply wiring for fire alarm detection devices (smoke detectors, CO Detectors) shall be connected to the control panel AUX output (located
on the main control panel board assembly).
l Power supply wiring for burglary alarm initiating devices (motion detectors, magnetic contacts, glass break detectors, etc.) shall be connected to
the compatible power supply modules AUX outputs (located on the power supply module board assembly, for example HSM3350, HSM3204CX) or
expander module AUX output (located on the expander module board assembly, for example HSM3408).
ULC Commercial Burglary Security Levels I-IV:
The following wireless PowerG devices models are ULC listed under ULC-S304 requirements for use in Commercial Burg applications rated for security level 1.
l PG9914 l PG9924 l PG9939 l PG9974P
l PG9905 l PG9929 l PG9944 l PG9984
l PG9920 l PG9934P l PG9945 l PG9984P
l PG9975 l PG9935 l PG9949 l PG9985
l PG9922 l PG9938 l PG9974 l PG9994
- 267 -
The wireless supervision window shall be set to 4h for such applications and the tamper detection for removal from mounting location shall be enabled.
UL Central Station and Police Connect with Standard or Encrypted Line Security Service
l The installation must use the integral Ethernet communicator or the plug-in cellular modules Models LE9080, 3G9080 or 3H9080, which communicates over Cel-
lular Data Network or an Ethernet network 10/100BaseT to the compatible Sur-Gard System I/II/III/IV/5 receiver.
l Polling time shall be 200 seconds and compromise detection time shall be 6 minutes.
l For Encrypted line security applications, the integral Ethernet communicator or the plug-in cellular modules Models LE9080, 3G9080 or 3H9080 shall have the
Encryption Key enabled (AES128 bit encryption algorithm is validated under NIST Certificate No.5371 and 5372.)
l Wireless Supervision window shall be enabled (refer to Wireless Programming, sections [804]>[802].)
l Open/Closing acknowledgment shall be enabled (Not required for Police Station connected systems.)
l Bell test for police station connect.
UL Local, Central Station and Police Connect with No Line Security Service
l All zones shall be programmed as end-of-line supervised.
l All intrusion zones shall be programmed as audible.
l The installation shall use a Bell UL Listed for Mercantile local alarms (e.g., Honeywell Model AB-12M bell housing). Connections from the control unit to the bell
shall be made in conduit. (Optional for central Station).
l The Bell shall be tested daily. Alternate option is to have bell squawk enabled for arming/disarming. The Bell activation cannot be delayed for more than 5 mins.
l The bell timeout shall be programmed for 15 minutes minimum.
l At least one system remote keypad with tamper switch shall be employed
l The integral communciator (DACT/IP) or plug-in cellular module shall be enabled and shall be programmed to provide a low battery transmission.
l The control panel shall be in a separately listed HSC3030CAR attack resistant enclosure.
l The maximum entry delay time shall not exceed 45s (25s for a local) as a result of the attack test. The maximum exit delay time shall not exceed 60 s.
l A tamper switch shall be used to protect the enclosure cover of the control unit. A tamper switch shall also be used on the keypad rear to detect removal from the
wall.
l 24 h check in transmission shall be enabled.
l Open/Closing acknowledgement enabled.(Not Police Station).
l The Installation shall use the internal communicator (DACT or IP) alone or in conjunction with plug-in cellular modules Models LE9080, 3G9080 or 3H9080, which
communicate over Cellular Data Network or an Ethernet network 10/100BaseT to the compatible Sur-Gard System I/II/III/IV/5 receiver.
UL Home Health Care Signaling Equipment
l There must be at least two keypads, one of the compatible keyapds models HS2LCDPRO, HS2LCDRFPRO9, HS2LCDWFPRO9, HS2LCDWFVPRO9,
HS2TCHPRO(BLK).
l Each system shall be programmed to activate an audible Trouble signal within 90 seconds upon loss of microprocessor memory
ULC Central Station Fire and Burglary Monitoring Installations
l For installation requirements, levels of security, communication modules and configurations (Refer to the ULC Installation Guide for PowerSeries Pro, P/N
#29010346).
l HS2TCHPRO(BLK) touch screen keypad is for supplementary use only with ULC Commercial Fire Monitoring.
l For Commercial Fire monitoring, the primary power failure transmission may be delayed up to 3h and Bell shall be disabled.
Note: As per ULC Bulletin 2017-02A, ULC Fire and Security Systems Group is accepting the use of MFVN digital telephone services for connection of digital dialer
transmitters ULC listed to be connected to the public switched telephone network communication system. Since the MFVN communication channel technologies
available are not provided with 24 hour standby power on the equipment and facilities used between the premises and the signal receiving center, it is required that, for
passive communication channels used in monitored protective signaling system installations, the testing time of the passive communication channels should be
reduced from the current 24 hours to 6 hours to better ensure that the system and communication channels are operating in their intended manner to reduce the life
safety risk. A change in testing frequency for intrusion alarm systems is not required due to the many different levels of line security options available for these system
types, which should be applied based on communication supervision needs for each installation.
For PowerSeries Pro panels, the following programming options shall be adjusted to meet the new 6 hour test transmission when used in ULC-S561 compliant install-
ations:
l Section [022] turn option 4 ON for hours.
l Section [377] option [003] set to 006 (for 6 hours).
l Section [309] option [002] enable test transmission for all applicable receivers.
Programming
The notes in the programming sections of thePowerSeries Pro Reference Manual describing the system configurations for UL/ULC listed installations shall be imple-
mented.
Control of the Protected Premises
In order to have a UL certificated system, the protected area shall be under the responsibility of one ownership and management (i.e., one business under one name).
This may be a group of buildings attached or unattached with different addresses but under the responsibility of someone having mutual interest. The person of mutual
interest is not the alarm-installing company.
Note: This does not apply to strip mall applications where each independent business must have their own separate alarm system.
e.g.,1: A commercial partitioned system that has an office and a warehouse area in a building where each area can be armed or disarmed independently. e.g.,2: A res-
idential system partitioned so that the garage area is armed separately from the house.
Each of the above examples is under the sole responsibility of a single owner. The bell and DACT power supply must be in a protected area including partitioned sys-
tems. The bell and DACT power supply must be located where it can be heard by the person or persons responsible for maintaining the security system during the
daily arming cycle.
Bell Location
The alarm sounding device (bell) shall be located where it can be heard by the person operating the security system during the daily arming and disarming cycle.
Protection of the Control Unit
- 268 -
The local control unit and the local power supply must be protected in one of the following ways:
l The control unit and audible alarm device must be in a protected area which is armed 24 hours a day.
l Each partition must arm the area protecting the control unit and the audible alarm device power supply. This may require duplicate protection armed by each par-
tition. Access to this protected area, without causing an alarm, will require that all partitions be disarmed.
l In all cases described above, the protected area for the control unit must be programmed as not-bypassable.
Casual Users
The installer should caution the user not to give system information (e.g., codes, bypass methods, etc.) to casual users (e.g., service people) and to only give out
One-Time Use codes.
User Information
The installer should advise the user and note in the User’s Manual:
l Service organization name and telephone number
l The programmed exit and entry time
l Instructions to test system weekly
l Note that the installer code cannot arm or disarm the system
- 269 -
5.4 Aux loading and battery selection

HS3128/HS3032/ UL Resi Fire UL
UL Resi Fire
HS3248 PCB cur- Home Health
UL Resi Burg with wired CO ULC COM Fire EN50131 EN50131
rent draw = 120 UL Com Burg Care ULC Resi
ULC Resi Burg Detectors Monitoring Grade 2 Grade 3
mA Alarm cur- Fire ULC Com
UL985 6th Ed
rent = 700 mA Burg
30 h (AC fail
24 h + 4 min 24 h + 4 min +
Standby Time 4 h + 4 min 4 h + 15 min transmission
24 h + 5 min 12 h CO alarm 24 h + 30 min 12 h
and Alarm Time 4 h + 5 min required)
24 h + 4 min
60 h
Enclosure HSC3010C HSC3030CAR HSC3010C HSC3010C HSC3010CR HSC3020C HSC3020C
HS65WPSNA
HS65WPSNAS
Power Supply (ULC CB Security
HS65WPSNA HS65WPSNA HS65WPSNA HS65WPSNAS HS65WPS HS65WPS
Adapter Level 4) (Require
high voltage barrier
kit)
4 Ah/700 mA 4 Ah/700 mA 17 Ah/500
7 Ah/250 mA
Battery capacity 7 Ah/1200 mA 7 Ah/1200 mA 14 Ah/330 mA 14 Ah/500 mA 17 Ah/ mA
14 Ah/500 mA
/max loading 14 Ah/2000 mA 14 Ah/2000 mA 17 Ah/400 mA 17 Ah/600 mA 1200 mA 17 Ah/250
17 Ah/600 mA mA
17 Ah/2000 mA 17 Ah/2000 mA
Low (400 mA) for Low (400 mA) for
Recharging cur- Low High
4 Ah/High (700 4Ah/High (700 High (700 mA) High (700 mA) High (700 mA)
rent setting (400 mA) (700mA)
mA) mA)
Note: For NFA2P 2 shield installations, use 18 Ah batteries and 450 mA load for 36-hour standby. For NFA2P 3 shield install-
ations, use 18 Ah batteries and the same loadings as for EN50131 Grade 3 in the table above.
5.5 SIA False Alarm Reduction Installations: Quick Reference

Minimum required system consists of one Control unit model HS3032, HS3128, or HS3248, and any one of the compatible
listed keypads (refer to Model comparison).
The following wireless keyfobs can also be used in SIA compatible installations: PG9929, PG9939,PG9949.
Note: For models PG9929 and PG9939, the panic/emergency key shall be disabled for SIA compliant installations.
For a list of the default values programmed when the unit is shipped from the factory, and for other programming information,
refer to the following table.
The following optional subassembly modules also bear the SIA CP-01-2014 classification and may be used if desired:
HSM2108 zone expander, HSM2208 PGM output module, HSM2300 auxiliary power supply, HSM2204 output module,
HSM2HOST9 2-way wireless transceiver, PG9901 indoor siren, PG9911 outdoor siren, and LE9080/3G9080/3H9080 cel-
lular and PSDN communication module.
Caution
l For SIA FAR installations use only modules/devices that are listed on this page.
l Fire Alarm Verification feature (Auto Verified Fire Zone type [025]) is not supported on 2-wire smoke detectors zones,
model FSA-210B(T)(S)(ST)(LST)(R)(RT)(RD)(RST)(LRST). This feature may be enabled for 4-wire smoke detectors
only (FSA-410B(T)(S)(ST)(LST)(R)(RT)(RST)(LRST) and wireless detectors PG9916/PG9926). The fire alarm delay
is 60s.
l Call Waiting Cancel (Section [382], option 4) on a non-Call Waiting line will prevent successful communication to the
supervising station.
l All system smoke detectors must be tested annually by conducting an Installer Walk Test. Prior to exiting Walk Test
mode, a sensor reset must be done on the system, [*][7][2], to reset all latching 4-wire smoke detectors. Refer to the
installation instructions supplied with the detector for details.
- 270 -
Notes
l Programming at installation may be subordinate to other UL requirements for the intended application.
l Cross zones have the ability to individually protect the intended area (e.g. motion detectors which overlap).
l Cross zoning is not recommended for line security Installations nor is it to be implemented on exit/entry zones.
l This control panel has a communication delay of 30 seconds. It can be removed or increased up to 45 seconds by
the end user with installer consultation.
l The system shall be installed with the sounding device activated and the communicator enabled for transmission
using SIA or CID format.
l ULC commercial burglary installations require DEOL resistors.
Table 5-1 SIA quick reference
SIA Feature Programming Section Comments Range/Default Requirement
Range:45-
Exit Time 255 seconds Required
Access to Entry and Exit delays and Bell Time Out for the system.
[005]>[001], option 3 Default: 60 (programmable)
sec.
Exit Delay Restart Opening a Delay zone door after it has already been opened and Default:
Required
[018], option 7 closed during an exit delay restarts the exit delay timer. Enabled
If no exit after
Auto Stay Arm on Un-vacated
Function key: Forces the system to arm in Stay mode if the occupant full arm
Premises Required
does not exit the premises after pressing the Away function key. Default:
[001]>[001]-[248] Zone type 05, 06,09
Enabled
System times and audible exit beeps can be disabled when using the
wireless key to stay arm the system. When away arming, audible exit
beeps can not be disabled.
Exit Time and Progress
For remote arming (using keyfob), it is possible to program the instant
Annunciation/Disable or Remote Default:
stay arm (no exit delay). By default this option is OFF. Allowed
Arming Enabled
When arming/disarming with keyfob the bell squawk option shall be
[861]>[001]-[005], option 4
enabled.
The Bell shall be tested daily. Alternate option is to have bell squawk
enabled for arming/disarming
Range: 30 Required
Access to entry and exit delays and bell time out for the system
Entry delay(s) sec. to 4 min.
Note: Combined entry delay and communications delay (abort (programmable)
[005]>[001]-[008], options 1 and 2 Default: 30
window) shall not exceed 60s.
sec.
Abort Window for Non-Fire zones Access to zone attributes, i.e., swinger shutdown, transmission delay Default: Required
[002]>[001]-[248], option 7 ON and cross zone. May be disabled by zone or zone type. Enabled
Range: 00 - 45
Abort Window Time - for Non-Fire Access to the programmable delay before communicating alarms
sec. Required
zones Note: Combined entry delay and communications delay (abort
Default: 30 (programmable)
[377]>[002], option 1 window) shall not exceed 60 seconds.
sees
An audible tone is generated when an alarm is aborted during the Hard-coded
Abort Annunciation Required
abort window. ON
Duress Feature When this feature is enabled, selected user codes send a duress
reporting code to the central station when used to perform any Default: N Required
[*][5]> master code> user 2-95> 5> 2 function on the system. Section [019], option [6] must be enabled.
Range: 005-
Cancel Window Access to the communications cancel window. Minimum duration 255
[377]>[002], option 6 must be 5 minutes.
Default: 005
A Cancel was
Cancel Annunciation transmitted Required
Access to the reporting code for Alarm Canceled.
[308]>[001], option 8 Default:
Enabled
- 271 -
Programming
Cross Zoning Enables cross zoning for entire system. Zones can be enabled for required
Required
[042]>Selection 3, option 002 cross zoning via zone attribute option 8 in sections [002][101] - [248]. Default:
Disabled
Range: 000-
Burglary Verification Timer 255 sec.
Access to the programmable Cross Zone timer. Allowed
[005]>[000], option 3 Default: 60
seconds
Swinger Shutdown for Alarms Access to the swinger shutdown limit for zone alarms. Required
Default: 2 trips
[377]>[001], option 1 For all non-fire zones, shut down at 1 to 6 trips. (programmable)
Non-police
Access to swinger shutdown, transmission delay and cross zone response
Swinger Shutdown Enable
attributes. Zone attribute option 6 (Swinger Shutdown enabled) is zones Allowed
[002]>[001] - [248], option 6 ON ON. Default:
Enabled
24-Hr. Auto-verified Fire Access to 24-Hr. Auto-verified Fire. Must choose

zone type for Required
[001]>[001]-[248], Zone type 025 ON Activates if Not restored within the specified time. application
Depends on
user phone
Call Waiting Cancel Access to the dialing sequence used to disable call waiting. Call waiting line
Required
[382], option 4 OFF string can be programmed in [304].
Default:
Disabled
System Test: The system activates all keypad sounders, bells or sirens for 2
[*][6] Master Code, option 04 seconds and all keypad lights turn on. Refer to user manual.
Walk Test Mode: This mode is used to test each zone on the system for proper
[*][8][Installer code][901] functionality.
Walk Test Communications Default:
Enables communication of zone alarms while walk test is active.
[382], option 2 Disabled
Walk Test Start/ End Reporting Codes
Access to the reporting codes for walk test start and end times.
[308][401], options 1 and 2
Duress codes function the same as user access codes, except they transmit a duress reporting code
when used to perform any function on the system. Duress codes cannot be used to access [*][5], [*][6] or
Duress Code [*][8] menus.
Duress codes are created by the master user or supervisor users
5.6 EUROPEAN EN50131 COMPLIANCE STATEMENT

This Product (HS3032/HS3128/HS3248) meets the requirements of Grade 3, Class II equipment as per EN50131-1:2006 +
A1:2009 + A2:2017 Standards. The Model HS3032, HS3128, HS3248 Control Panel has been certified by Telefication
according to EN50131-1: 2006 +A1:2009+A2:2017, EN50131-3:2009 Type B, EN50131-6:2017 Type A, EN50131-10,
EN50136-2:2013 ATS SP3 (dialer), SP4 (Ethernet), DP2 (dialer and Ethernet), DP3 (Ethernet and plug-in cellular) when
installed in enclosure models HSC3020C or HSC3020CP.
Note: The Model HS3032P, HS3128P, HS3248P consisting of Control Panel board assembly HS3032, HS3128, HS3248
with HSM2HOST8 Wireless Transceiver mounted in the HSC3020CP plastic enclosure meets the requirements of Grade 2,
Class II equipment as per EN50131-1:2006 + A1:2009 + A2:2017 Standards. The model HS3032P, HS3128P, HS3248P
has been certified by Telefication according to EN50131-1: 2006 +A1:2009+A2:2017, EN50131-3:2009 Type B, EN50131-
6:2017 Type A, EN50131-10, EN50136-2:2013 Grade 2, Class II, ATS SP3 (dialer), SP4 (Ethernet), DP2 (dialer and Eth-
ernet), DP3 (Ethernet and plug-in cellular) when installed in enclosure models HSC3020CP.
This product is suitable for use in systems with the following notification options:
- A - use of two remotely powered warning devices and one ATS SP3 required (internal dialer or ethernet or plug-in cellular
module)
- 272 -
- B - use of one self-powered warning device and one ATS SP3 required (internal dialer or ethernet or plug-in cellular mod-
ule)
- C - use of dual path ATS DP2 required (any combination of internal dialer and ethernet and/or cellular module)
- D - use of an ATS SP4 required (internal ethernet or plug-in cellular module with encryption enabled)
- E - use of dual path ATS DP3 required (combination of internal ethernet and plug-in cellular module with encryption
enabled)
For EN50131 compliant installations, with alarm control panels HS3248, HS3128 and HS3032, only the intrusion portion of
the alarm system may be activated.
For EN50131 compliant installations, the following functions must be disabled:
- Fire Alarm
- CO Alarm
- Auxiliary (Medical) Alarm functions
- In Section 861-21, options 1 and 2 must be off.
For EN50131 compliant installations, the following zone types must not be used:
007 – Delayed 24-Hour Fire 041 -– 24-Hour CO 049 – 24-Hour Flood
008 – Standard 24-Hour Fire 045 – 24-Hour Heat 052 – 24-Hour Non-Alarm
025 – Auto Verified Fire 046 – 24-Hour Medical 056 – 24-Hour High Temperature
027 – Fire Supervisory 047 – 24-Hour Emergency 057 – 24 Hour Low Temperature
040 – 24-Hour Gas 048 – 24-Hour Sprinkler* 071 – Door Bell
In this configuration, no non-mandatory events are generated in the Event Buffer and compliance with minimum 500 man-
datory events storage (Grade 3) is ensured as per Section 8.10.1 in EN50131-3. Compliance labeling should be removed or
adjusted if non-compliant configurations are selected.
- 273 -
Notes for EN50136-1:2012 compliant installations - Applicable to integrated phone line and Ethernet communicator
only.
The communicator operates in pass-through mode and it does acknowledge the alarm to the compatible control panel after
an acknowledgement has been received from the compatible alarm receiver.
1. The integrated communicator is monitored by the control panel and is programmed via the menu available from the
compatible keypad connected to the alarm control panel HS3248, HS3128, HS3023.
2. The communicaton path is immune to conducted and radiated RF fields, with levels up to 10V/m as tested per
EN50130-4 Standard.
3. The control panel with integrated communication module conforms with radiated emissions levels for Class B equip-
ment as per standards EN61000-6-3/EN55032/CISPR32.
4. The control panel has two integrated communication paths: Phone line dialer and Ethernet (IP) communication path.
These can be used in an ATS with the following categories:
l Single Path mode SP3 (Phone line dialer) or SP4 (IP path), or
l Dual Path mode DP2 integrated Ethernet (IP) path in conjunction with the compatible control panel
HS3248/HS3128/HS3032 integrated PSTN communicator, or
l Dual Path DP3 integrated Ethernet (IP) path in conjunction with the plug-in cellular module 3G9080-EU or
GS9080.
5. The integrated Ethernet (IP) communication path uses sequential authentication for substitution security and encryp-
tion AES128 bit for information security. The AES128-bit key is validated by NIST, Certificate No. 5371.
6. The integrated communicators have been tested for compliance in conjunction with the following applicable stand-
ards: EN50136-1:2012, EN50136- 2:2013, EN50131-10:2014, Grade 3, Class II, ATS configuration: SP3, DP2, DP3.
For EN50131-1:2006/A1:2009 /A2:2017 compliant installations, the following programming options must be set as
described: Supervision heartbeat set to 180 seconds for SP4 and DP3 configuration, along with the ARC receiver
supervison window set to 180 seconds. For DP2 configuration, the supervison must be set to 30 minutes.
This product is in conformity with the Electromagnetic Compatibility Directive 2014/30/EU, the Low Voltage Directive
2014/35/EU, and the RoHS3 Directive (EU) 2015/863.
The product is labelled with the CE mark as proof of compliance with the above mentioned European Directives. Also, a CE
declaration of conformity (DoC) for this product can be found at www.dsc.com under the Agency Listings section.
5.7 UK Compliance Statement

In the UK this product is suitable for use in systems installed to conform to PD 6662:2017 at Grade 3 and environmental
class II with the following notification options: A, B, C, D, E.
Where HS3032, HS3128 and HS3248 are used with a single path signaling method (such as the Integrated Digital Dialer),
please note the following limitation:
IMPORTANT
Your attention is drawn to the fact that failure or compromise of single path signaling cannot be passed to the police. While
the failure persists, subsequent alarms cannot be notified to the alarm receiving centre and passed to the police.
Setting Methods
The HS3032, HS3128 and HS3248 are capable to support the completion of the full setting procedure by the following meth-
ods:
a) push button switch, mounted outside the supervised premises; or b) protective switch (i.e., door contact) fitted to the final
exit door of the alarmed premises or area. The setting procedure is a two-stage process of initiating the setting procedure
within the supervised premises (e.g., using Mini Prox Tag (MPT) or user code) followed by completion of setting by one of
the two methods mentioned above. Please check with the Installer which method has been enabled for your system.
Unsetting Methods
The HS3032, HS3128 and HS3248 is capable to support the following unsetting methods in accordance with BS8243:
6.4.2 Prevention of entry to the supervised premises before the alarm system is unset. Unsetting using remote key before
entering the supervised premises causes or permits the initial entry door to be unlocked.
6.4.5 Completion of unsetting using a digital key (e.g., MPT or PG8929, PG8939, PG8949) either before entering the pro-
tected premises (use PG8929, PG8939, PG8949) or after entering the protected premises (use MPT). The entry delay is activ-
- 274 -
ated if the initial entry door is opened before the HS3032/HS3128/HS3248 have been unset. During the entry time, it is pos-
sible to unset the alarm system using a digital key only. Complete unsetting before programmed entry delay expires.
IMPORTANT
If using a remote device to remotely set/unset your intruder alarm system, your attention is drawn to the fact that whenever a
premises is unattended but its intruder alarm system(s) is (are) not fully set, any related insurance cover might be inop-
erative. For advice on this matter, it is recommended that you consult your insurer(s).”
The CIE and notification equipment should be located and supervised to minimize the risk of vandalism or sabotage. It is
preferable for the CIE, signaling and network equipment to be located in an area where a confirmed activation will be gen-
erated.
HS3032, HS3128 and HS3248 are compliant with criteria for sequentially confirmed intruder alarm systems as per Standard
BS8243:2010.
For an alarm condition to be regarded as sequentially confirmed:
a) The HS3032, HS3128 and HS3248 should be configured so that at least two separate alarm conditions are reported,
each originating from an independent detector within the confirmation time; Section [042] option 003 (Sequential Detection),
section [005]>[000], Burglary Verification.
Timer set to a value between 30 and 60.
b) The two detectors should either be of:
1) different technologies which are permitted to have overlapping areas of coverage; or
2) the same single technology and not have overlapping areas of coverage.
To be regarded as independent, each detector should be configured to report alarm conditions separately to the HS3032,
HS3128 and HS3248.
The HS3032, HS3128 and HS3248 are capable of supporting the completion of the full setting procedure by one of the fol-
lowing methods:
a) push button switch mounted outside the supervised premises. Instructions to be provided for the zone type to be pro-
grammed for the key
arming; or
b) protective switch (i.e., door contact) fitted to the final exit door of the alarmed premises or area. Use zone type 016 (Final
Door Set) for the final exit door.
In this case the setting procedure is a two-stage process of initiating the setting procedure within the supervised premises
(e.g., using wireless key PG8929,PG8939, PG8938, PG8949 or user code) followed by completion of setting by one of the
two methods described above.
This prohibits the use of a timed exit procedure.
If a protective switch (i.e. door contact) is used as the method of completion of setting, then the keypad should be sited near
to the final exit door so that the IAS can be unset promptly. Where appropriate, additional internal audible indications
(PG8911 indoor sirens) should be provided so that persons within a building are informed that the HS3032, HS3128 and
HS3248 are due to be set. Additional keypads should be provided, where appropriate, so that if the alarm panel is set there
are means available locally within the supervised premises to unset the system.
HS3032, HS3128 and HS3248 are capable of supporting the following unsetting methods in accordance with BS8243:
6.4.2 Prevention of entry to the supervised premises before the HS3032, HS3128 and HS3248 are unset. Unsetting using
PG8929,PG8939, PG8938, PG8949 wireless key before entering the supervised premises causes or permits the initial entry
door to be unlocked. Program PGM1 or PGM2 in Section [009] to activate when system is disarmed and release the mag-
lock on the entry door.
- 275 -
Appendix 6: Wiring diagrams

6.1 HS3032, HS3128, and HS3248 UL/ULC wiring diagram (North America only)
HS3032/HS3128/HS3248 UL/ULC Wiring Diagram
APPLICABLE UL STANDARDS UL File No. S4019
UL1610 Central Station Burglar Alalrm Units UA718
PC LINK MICRO-B
UL365 Police Station Connected Burglar Alarm Units & Systems *AUX Wiring
USB TYPE A
UL609 Local Burglar Alarm Units and Systems
LE9080 Use No.14-22 AWG conductor.
UL985 Household Fire Warning System Units
UL1023 Household Burglar Alarm System Units Warning: Disconnect AC power and 3G9080 AUX+ and Corbus (RED) are internally connected.
3H9080
Total current draw from keypads, PGM Outputs
UL1635 Digital Alarm Communicator System Units telephone lines before servicing. and AUX circuits must not exceed 2000 mA.
UL1637 Home Health Care Signaling Equipment
ANSI/SIA CP-01-2014 Attention: Débranchez l’alimentation Note: Refer to the Installation Manual for maximum
ULC-S304:16 Standard for Control Units, Accessories and Receiving Equipment for current loading levels associated with different
Intrusion Alarm Systems secteur et lignes téléphoniques avant applications.
ULC-S559-13 Equipment for Fire Signal Receiving Centers and Systems
ULC-S545-02 Residential Fire Warning System Control Units
l’entretien.
NOTE: For UL1637 applications, installation must be done only by a trained installer. All circuits are classified for UL installations as power limited/Class II power limited, except for the
SIA-FAR Min System Requirements: battery leads which are not power limited. Do not route any wiring over circuit boards. Maintain at
1. HS3032/3128 Panel least 1” (25.4 mm) separation. A minimum 1/4” (6.4 mm) separation must be maintained at all Earth ground connection
2. Local annunciation devices points between power limited wiring and all other non-power limited wiring. Inspect wiring and from building electrical
ensure connections are correct before applying power. Use metal standoff and screw in the position indicated. installation.
Local Annunciation Devices may be any combination of the keypads:
BATTERY IMPORTANT! Ensure screw and standoff are tightly
HS2LCDPRO, HS2TCHPRO(BLK), HS2LCDRFPRO9, NOTE: this ground
secured ot establish Earthground connection for the
HS2LCDWF(V)PRO9 PCB. connection goes to
Alarm Bell: Internal BELL output circuit or wireless sirens PG9911 or HS65WPSNA power
PG9901 adapter EGND
Remote Transmission: internal DACT or Ethernet or plug-in Cellular DC AUX BELL CORBUS PGM AUX ZONE ZONE ZONE ZONE TELCO connections when this
module LE/3G/3H9080 ETHERNET
power adapter is mounted
in the cabinet.
550 mA*
(see Aux PGM4: 100 mA (max)
Out to premisis telephone
18 VDC/65 W wiring PGM3: 300 mA (max)
note above) PGM2: 300 mA (max) In from telephone company
BATTERY BATTERY 120 VAC/60 Hz HS65WPSNA
12V 7Ah 12V 4.0Ah/7Ah/17Ah Primary PGM1: 100 mA (max) RJ-31X Telephone Plug 26 AWG
power adapter
Maximum battery
charge current is NOTE: For ULC
400mA/700mA
(selectable based on Commercial Fire Monitoring 2-WIRE SMOKE DETECTORS
Compatible DSC 2-wire NAME MODEL COMPATIBILITY ID MAX # BASE
the application. Refer applications use Model
to Installation Manual) ULC-LA smoke detectors: DSC FSA-210B FS200 DSC NONE
HS65WPSNAS. FSA-210A Series for ULC
(optional) Series
NOTE: Refer to Installation Manual for proper battery FSA-210B Series for UL
capacity selection, based on the intended application. Bell/Siren
Compatible FSA-210C Series for EU Compatibilty Identifier: HS3-1
NOTE: DO not connect power adapter to receptacle 10.8-12.5 VDC Maximum Operating Voltage: 13.8 VDC
System Keypads Maximum Number of Detectors: 18
controlled by a switch. 700mA (max) 10.8-12.5VDC
For Fire/Bell wiring refer to Reference Manual. 2200 DO NOT combine
Observe Polarity
POWER LIMITED
END-OF-LINE different models on the
RESISTOR
Cable ties (not supplied) recommended PGM CONNECTIONS EOLR-3
same circuit as
operation may be
NOTE: Refer to the
impaired.
FSA-210 Installation Manual for more details.
PC LINK MICRO-B
USB TYPE A
4-WIRE SMOKE DETECTORS

Smoke detector must To reset smoke detector, Compatible DSC 4-wire
HS3032 PCB be latching type (e.g., enter [ * ][7][2] smoke detectors:
HS3128 PCB DSC FSA-410B Series) FSA-410A Series for ULC
FSA-410B Series for UL
HS3248 PCB FSA-410C Series for EU
BATTERY UA718
Zone input Lorem ipsum
COM BLK
DC AUX BELL CORBUS PGM AUX ZONE ZONE ZONE ZONE TELCO
ETHERNET
IN Alarm
initiating
IN NO loop
OUT resistance
ALM
100
OUT
IMPORTANT: Minimum
EOLR-2
6.4 (1/4”) separation WHT RED GRN
END-OF-LINE-
must be maintained
RESISTOR
between RM-1 circuits
4Ah 5600 0.5W
Black - and all other wiring. NOTE: Refer to Installation Manual & Smoke Detector
7Ah
2 x 7Ah
Instruction Sheet when locating detectors.
Red + 17Ah
TYPICAL ZONE CIRCUITS AC wiring details for ULC-561 using HSC3010CR
NOTE: Maximum line impedance 100 Not required for UL/ULC.
Single End-of-Line Resistor Wiring enclosure
Double End-of-Line Resistor Wiring Triple End-of-Line
Resistor Wiring
Mask
RESISTOR /Fault
IDENTIFICATIONS
2-WIRE SMOKE 3
Circuit Control Unit Smoke Detector

NOTE: For UL listed applications, use Model EOLR-1 (zone) Delay - Sec Models Delay (seconds)
Control panel is suitable for
SINGLE ZONE EOL 25 30 PG9926/PG9916 (a) the following UL installations:
4-Wire UL Listed 4-Wire ULC Listed INSTALLATION TYPE
UL/ULC Resi Fire and Burg
FSA-410B /FSA-410BT/ FSA-410A/FSA-410AT/ UL Local Mercantile
FSA-410BS/FSA-410BST/ FSA-410AS/FSA-410AST/ UL Central Station (Burglary)
25 30 FSA-410BLST/FSA-410BR/ FSA-410ALST/FSA-410AR/ (a) UL Police Station Connected (Burglary)
NOTE: For UL listed applications, use Model EOLR-2 ULC Central Station (Burglary)
FSA-410BRT/FSA-410BRS/ FSA-410ART/FSA-410ARS/ ULC Central Station Fire Monitoring
BELL CIRCUIT FSA-410BRST/ FSA-410ARST/ SIGNALING MEANS
FSA-410BLRST FSA-410ALRST DACT, PSDN (IP/Cellular Data) NA
DACT (no line security), PSDN (Standard/Encrypted Line Security, use with
WARNING: THIS UNIT INCLUDES AN ALARM VERIFICATION FEATURE THAT WILL (a) The delay (power-up) time marked Internal Ethernet communicator and/or plug-in cellular module, models
RESULT IN A DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED on the installation wiring diagram of the LE/3G/3H9080
CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL smoke detector or on the installed DACT (Passive Level P1), PSDN (Passive P1-3/Active A1-4) use with Internal
NOT EXCEED 60 SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED smoke detector(s) is to be used. Ethernet communicator and/or plug-in cellular module, models LE/3G/3H9080
TO THESE CIRCUITS UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING DACT+PSDN (Passive), PSDN (Active), use with Internal Ethernet
NOTE: For UL listed applications, use Model EOLR-3 JURISDICTION. communicator and/or plug-in cellular module, models LE/3G/3H9080
WARNING: Not to be removed by anyone except occupant. HS3032/3128/HS3248 UL Resi Burg UL COM Burg UL Resi Fire UL Resi Fire with ULC COM EN50131 EN50131
This equipment should be installed in accordance with PCB current draw= 125 ULC Resi Burg UL, HH, ULC Resi Fire wired CO Detectors fire Grade 2 Grade 3
Chapter 29 of the National Fire Alarm and Signaling Code, mA alarm current=700 mA ULC Com Burg UL985 6th Ed Monitoring
ANSI/NFPA 72, (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269). Printed information Standby time + alarm time 4 hr + 4 min 4 hr + 15 min 24 hr + 4 min 24 h + 4 min + 24 h + 30 min 12 hours 30 hr (AC fail
describing proper installation, operation, testing, 4 hr + 5 min 24 hr + 5 min 12 hr CO Alarm transmission)
maintenance, evacuation planning, and repair service is to 24 hr + 4 min
be provided with this equipment. For compliance with Enclosure HSC3010C HSC3030CAR HSC3010C HSC3010C HSC3010CR HSC3020C HSC3020C
UL985, at least one smoke detector is required. Test the
system at least once per week. The system is intended to Power supply adapter HS65WPSNA HS65WPSNA HS65WPSNA HS65WPSNA HS65WPSNAS HS65WPS HS65WPS
be checked by a qualified technician at least every 3 years. HS65WPSNAS (ULC CB
For UL1637 installations, the test must also be performed Security Level 4. Require
with the AC off, using the standby battery. High Voltage Barrier Kit)
This device complies with Parts 15 and 68 of the FCC rules. Battery capacity/ 4 Ah/700 mA 4 Ah/700 mA 7 Ah/250 mA 14 Ah/330 mA 14 Ah/500 mA 17 Ah/1200 mA 17 Ah/500 mA
Operation is subject to the following 2 conditions: [1] this max loading 7 Ah/1200 mA 7 Ah/1200 mA 14 Ah/500 mA 17 Ah/400 mA 17 Ah/600 mA
device may not cause harmful interference and [2] this device 14 Ah/2000 mA 14 Ah/2000 mA 17 Ah/600 mA
must accept any interference received, including interference
that may cause undesired operation. 17 Ah/2000 mA 17 Ah/2000 mA
Models: HS3032/HS3128/HS3248 Recharging current Low (400 mA) Low (400 mA) High (700 mA) High (700 mA) High (700 mA) Low (400 mA) High (700 mA)
US: F53AL01AHS3256 REN = 0.1 setting High (700 mA) High (700 mA)
Plug Type: RJ-31X
IC: 160A-HS3256 Temperature Range: 0°C-49°C [32°F-120°F] / Maximum Humidity: 93% R.H.
ULC Notes For detailed installation and operating instructions, refer to the Installation Guide #29010135, and the User Manual #29010134. The
• For ULC Listed Fire Monitoring Installations & module HS3032/HS3128/HS3248 is UL Listed for limited energy installations per NEC Article 760. Recognized limited energy cable should be
requirements, please refer to the ULC Installation used. Observe NEC wiring requirements and local codes defined by the authority having jurisdiction. Security detection devices that
Information Sheet, part number 29010346. require power from the control panel must be UL Listed for the intended application and operate over the range of 10.8-12.5VDC. The DSC
• All tamper circuits may be connected to the same zone. Bravo Series are recommended UL Listed motion detectors. Compatible system keypads: HS2LCDPRO, HS2TCHPRO(BLK),
HS2LCDRFPRO9, HS2LCDWF(V)PRO9.
- 276 -
6.2 HS3032 and HS3248 wiring diagram (EN50131 only) HSC3020C enclosure
POWER LIMITED
Cable ties (not supplied) recommended STANDOFF
PC BOARD
Tamper switch
and mounting
bracket
PC LINK
USB TYPE A
MICRO-B CABINET
1. Insert standoff into cabinet mounting hole in the

HS3032/HS3128/ desired location. The standoff makes an audible
“click” when properly inserted.
HS3248 2. Position circuit board mounting holes over
Use No. 14-22 AWG size wire
standoffs. Press firmly on board to snap in place.
UA718
BATTERY
indicated.
Cable tie
required
Cable tie
1x17 Ah/12V or for NFA2P required
1X18Ah/12V sealed lead

acid type battery To power adaptor AC IN
module (Blue-Neutral) (Blue-Neutral)
To power adaptor module EGND
(Green/Yellow-EGND) (Green/Yellow)
To power adaptor AC in
module (Brown-Live) (Brown-Live)
Replace fuse with same type (20 mm) rated

250V/3.15A Slow Blow
Power supply Primary: 100-240V AC, 50-60Hz, Class 6
mounting screws Secondary: 18V DC, 3.6A
Power adaptor: HS65WPS
- 277 -
6.3 HS3032 and HS3248 wiring diagram (EN50131 only) HSC3020CP enclosure
6.4 Zone wiring

Zones can be wired for Normally Open or Normally Closed Contacts, with Single-end-of-line (SEOL), Double-end-of-line
(DEOL) or Triple-end-of-line (TEOL). Observe the following guidelines.
Note: For UL Listed Installations, use SEOL or DEOL only.
Minimum 22 AWG wire, maximum 18 AWG.
Do NOT use shielded wire.
Wire run resistance shall not exceed 100Ω, refer to the chart below:
Wire Maximum Wiring Length to End of Line Resistor (feet/-
Gauge meters)
22 3000 / 914
20 4900 / 1493
19 6200 / 1889
18 7800 / 2377
- 278 -
Normally Closed Loops - Do NOT use for UL Installations
Single End-of-Line Resistor Wiring
Double End-of-Line Resistor Wiring
Triple End-of-Line Resistor Wiring
Mask 3
/Fault
AND 10000 MASK RESISTOR
EOL loop resistance is programmable. See programming section 004.

Section [001] Selects Zone Definition
Section [013] Opt [1] Selects Normally Closed or EOL resistors
Section [013] Opt [2] Selects Single EOL or Double EOL resistors.
Zone status-loop resistance/status
Loop Status Loop Resistance
SEOL (standard) SEOL (Fire) DEOL TEOL
Fault — Infinite 0Ω 15,600Ω
Secure 5600ΩΩ 5600Ω 5600Ω 5600Ω
Tamper — — Infinite Infinite
Violated 0Ω/Infinite 0Ω 11,200Ω 11,200Ω
Masking — — — 21,200Ω
6.5 Bell wiring

These terminals supply 700mA of current. Ratings:
UL/ULC applications: 10.8 Vdc - 12.5 Vdc.
EN50131 applications: 10 Vdc - 14 Vdc.
- 279 -
To comply with NFPA 72 Temporal Three Pattern requirements, program Section [013] Opt [8] ON.
The Bell output is supervised and power limited. Connect a 1000 Ω resistor across Bell+ and Bell- to prevent the panel from
displaying a trouble. See [*][2].
Figure 6-1 Bell wiring
BE SURE TO OBSERVE POLARITY WHEN

CONNECTING POLARIZED SIRENS
OR BELLS
BELL LOOP 700mA CONSTANT CURRENT

(2A MAX)
Note: Bell output is current limited by 2 A. Steady, Fire Pulsed, Fire Temporal Three and CO Temporal Four pattern alarms
are supported.
6.6 Aux power wiring

These terminals provide 2A maximum of current (shared with PGM outputs). Connect the positive side of any device to the
AUX+ terminal and the negative side to GND. The AUX output is protected; if too much current is drawn from these terminals
(wiring short), the output is temporarily shut off until the problem is corrected.
Ratings:
UL/ULC applications: 10.8 Vdc - 12.5 Vdc.
EN50131 applications: 10 Vdc - 14 Vdc.
6.7 Corbus wiring

The RED and BLK Corbus terminals are used to provide power while YEL and GRN are used for data communications. The
4 Corbus terminals of the alarm controller must be connected to the 4 Corbus terminals or wires of each module.
The following conditions apply:
l Corbus should be run with 18 to 22 AWG quad, two pair twisted preferred.
l The modules can be home run to the panel, connected in series or can be T-tapped.
l Do not use shielded wire for Corbus wiring.
Note: Any module can be connected anywhere along the Corbus. Separate wire runs for keypads, zone expanders etc. are
not necessary.
Note: No module can be more than 1000 ft / 305 m (in wire length) from the panel. Do not use shielded wire for
Corbus wiring.
Figure 6-2 Corbus wiring
Module (A) is wired correctly as it is within 1000 ft / 305 m of the panel, in wire distance. Module (B) is wired correctly as it is
within 1000 ft / 305 m of the panel, in wire distance. Module (C) is NOT wired correctly as it is farther than 1000 ft / 305 m
from the panel. For models that require more than 1000 ft / 305 m from the main panel, a HSM3204CX power supply/Corbus
extender can be used.
- 280 -
6.8 PGM wiring

PGMs switch to ground when activated by the control panel.
Connect the positive side of the device to the AUX+ terminal and the negative side to a PGM terminal.
The Minimum/maximum operating voltages for devices, sensors and modules is 9.8 Vdc - 14 Vdc.
Current output is as follows:
PGM1, PGM4: 100mA
PGM2, PGM3: 300mA
For currents levels greater than 300mA, a UL listed RM-1 or RM-2 relay module is required.
PGM2 can also be used for 2-wire smoke detectors.
PGM 1, LED output with current limiting resistor and optional relay driver output.
Note: Use only SEOL resistors on FIRE ZONES.

2-wire smoke detectors initiating circuit
l Style B (Class B), Supervised, Power Limited
l Compatibility Identifier HS3-1
l DC Output Voltage 9.4-13.8 VDC
l Detector Load 2 mA (MAX)
l Single-end-of-line (SEOL) Resistor 2200Ω
l Loop Resistance 24Ω (MAX)
l Standby Impedance 1250Ω (NOM)
l Alarm Impedance 664Ω (MAX)
l Alarm Current 97 mA (MAX)
l Maximum number of 2-wire Smoke Detectors 18
2-wire smoke detectors 4-wire smoke detectors

Compatibility ID For FSA-210 Series is: FS200
Compatible DSC 2-wire smoke detectors:
FSA-210A Series for ULC Compatible DSC 4-wire smoke detectors:
FSA-210B Series for UL FSA-410A Series for ULC
FSA-210C Series for EU FSA-410B Series for UL
RM-1/RM-2 POWER LOOP
FSA-410C Series for EU
SUPERVISORY RELAY
- 281 -
6.9 Telephone line wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x Connector as indicated.
For connection of multiple devices to the phone line, wire in the sequence shown.
Use 26 AWG wire minimum for wiring.
Telephone format is programmed in section [350].
Telephone Call Directions are programmed in section [311] - [318].
6.10 Earth ground wiring

Using the supplied insulated green wire, connect the earth ground terminal on the HS65WPSx power adapter to the earth
ground screw and nut assembly as shown in the diagram.
The earth ground screw and nut assembly must be mounted to the cabinet to one of the designated holes marked with the
earth ground symbol .

Figure 6-3 Earth ground installation
Item Description
1
1 Nut
2
2 Earth ground connection from building electrical installation.
3
Note: This ground connection goes to HS65WPSNA power
adapter EGND connections when this power adapter is mounted
4
in the cabinet.
5 3 Cabinet
4 Star washer
6 5 Bolt
6 Earth ground symbol
- 282 -
Appendix 7: Specifications
Zone Configuration
l 32, 128 or 248 wireless zones supported and up to 8 hardwired zones available on the controller
l 41 zone types and 15 programmable zone attributes
l Zone configurations available: normally closed, single EOL resistor, DEOL resistor, and TEOL resistor.
l Hardwired zone expansion (fully supervised) available using the model HSM2108 or HSM3408 (eight zone
expander module)
l Wireless zone expansion (fully supervised) available using the HSM2Host 2-way wireless integration module oper-
ating at 915 MHz (North America), 433 MHz (Europe) and 912-919 MHz (international)
Access Codes
l Up to 1003 access codes: 1000 (level 2-EN), one installer code (level 3-EN), one maintenance code, and one guard
code.
l Programmable attributes for each user code
l Access codes are either 4, 6 or 8 digits in length, depending on the setting of programming section [041]. Duplicate
codes are not valid.
Note: For EN50131-1 Grade 2 compliant systems using 100 access codes or less, 6 digit codes must be used. If using more
than 100 access codes, 8 digit codes must be used. For EN50131-1 Grade 3 compliant systems 8 digit codes must be used.
Warning Device Output
l 2 remote, wireless indoor/outdoor warning devices supported: models PGX901 (indoor), PGX911 (outdoor) (X=4, 8,
or 9)
l Programmable as steady, pulsed or temporal three (as per ISO8201) and temporal four (CO alarm) output
l Warning device sounds alarms in the following priority: fire, CO, burg
Note: For NFA2P certified systems the delay for operating the warning device shall be set to max. 10 min.
Memory
l CMOS EEPROM memory
l Retains programming and system status on AC or battery failure for 20 years min. (not verified by UL)
Power Supply - North America
l Power Supply:HS65WPSNA (cord connected) and HS65WPSNAS (hardwired, use in ULC Commercial Burg Secur-
ity Level IV and ULC Commercial Fire Monitoring applications)
l Primary: 120 VAC, 60 Hz, Energy Efficiency Class VI
l Secondary: 18 V DC, 3.6 A Limited Power Source (LPS)
l Model HS65WPSNA mounted in the same enclosure or outside, cord connected
l Model HS65WPS mounted in the same enclosure, permanently connected
Power Supply - International
l Power Supply: HS65WPS
l Primary: 100-240 V AC, 50 Hz, 1.7 A, Energy Efficiency Class VI
l Secondary: 18 Vdc, 3.6A, LPS
l Mounted in the same enclosure, permanently connected
Note: For installations using the power supply module mounted inside the cabinet, replace fuse only with the same type (20
mm) rated New fuse rating 250 V/3.15 A Slow Blow.
Regulated power supply:
l 3.6 A regulated, supervised
l Type A as per EN50131-6 Standard
l FET protected for Bell, Aux+ and Battery terminals
l Reverse battery detection/protection
l Supervision for input power and low battery
l Normal and high current battery charge options
l Supervised battery charging circuit
Current draw (control panel board assembly):
l 120 mA (nominal)
Bell Output:
- 283 -
l Ratings:
l UL/ULC applications: 10.8 V DC - 12.5 V DC
l EN applications: 10 V DC - 14 V DC
l 700 mA supervised (1 k Ohm) bell output (current limited at 2 amps)
l Steady, Pulsed, Temporal 3 fire, Temporal 4 CO alarm cadences
l Bell open short circuit detection (software + hardware)
Aux+:
l Ratings:
l UL/ULC applications: 10.8 V DC - 12.5 V DC
l EN applications: 10 V DC - 14 V DC
l Current = 2 A (shared with Corbus R(ed) and PGM outputs)
l Output ripple voltage: 600 mVp-p max.
l Onboard programmable outputs:
l PGM 1 - 100 mA switched programmable output
l PGM 2 - 300 mA current-limited switched programmable output. 2-Wire smoke detectors (100 mA current lim-
ited) are supported using this PGM
l Hardware PGM over current protection
l The voltage at any independent power output below which the power output fault signal or message is generated:
9.8 V DC
l Over-voltage protection trigger voltage: 15 V DC
Battery
l 12 V sealed lead acid, rechargeable
l Battery capacity: Refer to table "Aux loading and battery selection" on page 270
l Maximum standby time: Refer to "Aux loading and battery selection" on page 270 for each type of application.
l Recharging time to 80% 72 hours
l Recharging rate: 400 mA (12 hours max.), 700 mA (24 hour backup)
l Backup time: 24 hours (UL)
l Battery lifespan: 3-5 years
l Low battery trouble indication threshold 11.3 VDC
l Battery restore voltage 12.5 V
l Main board current draw (battery only):
l HS3032/HS3128/HS3248 (no alternate communicator) standby 100 mA DC
l HS3032/HS3128/HS3248, (including plug-in communicator) standby 120 mA DC
l Self-reseting FETs for short/overcurrent protection on the circuit board
l Internal clock locked to the internal Real Time Clock
The standby battery does not automatically recharge on reconnection of the AC mains (external power supply) if the battery
terminal voltage is less than 9.6 VDC.
The minimum energy level of the standby battery in a charged state (as a percentage of the rated capacity for the range of
batteries that can be used with the power supply) is 90% for 17 Ah batteries.
Operating Environmental Conditions
l Temperature range: UL/ULC: 0°C to +49°C (32°F to 120°F), For EN50131 applications: -10˚C to +55˚C
l Relative humidity: 5% to 93% RH non-condensing
Note: The alarm panel is not suitable for use external to the supervised premises.
Alarm Transmitter Equipment (ATE) Specification
l Digital dialer integral to the main control board
l Supports SIA and Contact ID
l Complies with TS203 021-1, -2, -3 Telecom equipment requirements and EN50136-1, EN50136-2, ATS SP3, DP2
(when used in conjunction with Ethernet and/or Cellular paths).
l The integral Ethernet communication port and optional plug-in cellular module (models 3G9080, 3H9080, LE9080
for UL/ULC and 3G9080-EU, GS9080 for EN50131 applications) can be installed in the same enclosure and con-
figured as primary or back-up, with AES 128-bit encryption.
l Compliant with EN50136-1, EN50136-2 ATS configurations SP4, DP3.
- 284 -
System Supervision Features

The PowerSeries Pro continuously monitors a number of possible trouble conditions and provides audible and visual indic-
ation at the keypad. Trouble conditions include:
l AC power failure
l Zone trouble
l Fire trouble
l Telephone line trouble
l Communicator trouble
l Low battery condition
l RF jam
l AUX power supply fault
l Failure to communicate
l Module fault (supervisory or tamper)
l Power unit failure
l System overcurrent
Additional Features
l 2-way wireless device support
l Visual verification (images + audio)*
l Proximity tag support
l PGM scheduling
l Quick arming
l User, partition, module, zone and system labels
l Soak test*
l Programmable system loop response
l Keypad and panel software versions viewable through keypad
l Doorbell zone type
l Low battery PGM type
*Feature not evaluated by UL/ULC.
Additional Notes for EN50131 Compliant Installations
l The alarm system can be set/unset wth 6 or 8-digit user access codes, or using compatible wireless keyfobs. During
the setting procedure, a setting indication is provided (exit delay annunciation). The setting is prevented if an alarm,
trouble, or tamper condition exists. An indication is given if the system fails to set following the initiation of the setting
procedure. The option to override a condition that prevents setting for the respective set period is provided. Override
is possible using a valid user access code. When the system is set, a 30 second timer begins. The Armed LED on the
keypad remains on for 30 seconds. When the system is in the set state, opening the door to the entry/exit route ini-
tiates the entry procedure. The system is unset using a valid user access code or an enrolled compatible keyfob.
l The alarm system does not support prioritization for indications.
l Masking signals are processed as intruder signals.
7.1 Locating detectors and escape plan

The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and
installing smoke and CO alarms.
Smoke Detectors
Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate
that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of
each sleeping area and on each storey of the home.
The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and
installing smoke alarms.
It is recommended that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be
protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not
protected by the required units. On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required
depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72,
CAN/ULC-S553-02 or other appropriate national standards for installation recommendations.
- 285 -
l Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may pre-
vent the unit from detecting smoke.
l Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector
may prevent smoke from entering the unit.
l Do not locate detectors in areas of high humidity.
l Do not locate detectors in areas where the temperature rises above 38ºC (100ºF) or falls below 5ºC (41ºF).
l Smoke detectors should always be installed in USA in accordance with Chapter 29 of NFPA 72, the National Fire
Alarm Code.
Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall
be installed as follows:
1. In all sleeping rooms and guest rooms.
2. Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel.
3. On every level of a dwelling unit, including basements.
4. On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and unfinished attics.
5. In the living area(s) of a guest suite.
6. In the living area(s) of a residential board and care occupancy (small facility).
Figure 1 Figure 2 Figure 3
Figure 3a Figure 4
Fire Escape Planning

There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a
family escape plan be developed and rehearsed.
1. Every family member should participate in developing the escape plan.
2. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes
from sleeping quarters.
3. Escape from a bedroom must be possible without opening the interior door.
Consider the following when making your escape plans:
l Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their
locking mechanisms operate smoothly.
l If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue should be
developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning
signal.
l If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use.
l Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in winter; outdoor
furniture or equipment should not block exits.
l Each person should know the predetermined assembly point where everyone can be accounted for (e.g., across the
street or at a neighbor's house). Once everyone is out of the building, call the fire department.
l A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings as
this can waste valuable time. Once outside, do not re-enter the house. Wait for the fire department.
- 286 -
l Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know
what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes
to the building’s construction.
l Make sure your fire warning system is operational by conducting weekly tests. If you are unsure about system oper-
ation, contact your installer.
l We recommend that you contact your local fire department and request further information on fire safety and escape
planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection.
Figure 5
Carbon Monoxide detectors

Carbon monoxide is colorless, odorless, tasteless, and very toxic, it also moves freely in the air. CO detectors can measure the concentration and
sound a loud alarm before a potentially harmful level is reached. The human body is most vulnerable to the effects of CO gas during sleeping hours;
therefore, CO detectors should be located in or as near as possible to sleeping areas of the home. For maximum protection, a CO alarm should be
located outside primary sleeping areas or on each level of your home. Figure 5 indicates the suggested locations in the home.
Do NOT place the CO alarm in the following areas:
l Where the temperature may drop below -10ºC or exceed 40ºC
l Near paint thinner fumes
l Within 5 feet (1.5m) of open flame appliances such as furnaces, stoves and fireplaces
l In exhaust streams from gas engines, vents, flues or chimneys
l In close proximity to an automobile exhaust pipe; this will damage the detector
PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING INSTRUCTION SHEET FOR SAFETY INSTRUCTIONS AND
EMERGENCY INFORMATION.
- 287 -
8.0 Limited warranty
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the
product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security
Controls shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for
labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or
ninety (90) days, whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that
there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty
period. There is absolutely no warranty on software and all software products are sold as a user license under the terms of
the software license agreement included with the product. The Customer assumes all responsibility for the proper selection,
installation, operation and maintenance of any products purchased from DSC. Custom products are only warranted to the
extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.
International Warranty
The warranty for international customers is the same as for any customer within Canada and the United States, with the
exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized dis-
tributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls must first obtain an
authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not
been obtained.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:
l damage incurred in shipping or handling;
l damage caused by disaster such as fire, flood, wind, earthquake or lightning;
l damage due to causes beyond the control of Digital Security Controls such as excessive voltage, mechanical shock
or water damage;
l damage caused by unauthorized attachment, alterations, modifications or foreign objects;
l damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);
l defects caused by failure to provide a suitable installation environment for the products;
l damage caused by use of the products for purposes other than those for which it was designed;
l damage from improper maintenance;
l damage arising out of any other abuse, mishandling or improper application of the products.
Items Not Covered by Warranty
In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the
repair centre; (ii) products which are not identified with DSC's product label and lot number or serial number; (iii) products
disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to
verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at
DSC's option. Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be
evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid purchase order is received
from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of
attempts will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under no cir-
cumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based upon
breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are
not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement
equipment, facilities or services, down time, purchaser’s time, the claims of third parties, including customers, and injury to
property. The laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such a
jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest
extent permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that
the above may not apply to you.
- 288 -
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied
(including all implied warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities
on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other
person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability
concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of
Ontario, Canada.
WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product
to fail to perform as expected.
Out of Warranty Repairs
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory accord-
ing to the following conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number.
Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.
Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital
Security Controls has predetermined and which may be revised from time to time, will be charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equivalent product
available at that time. The current market price of the replacement product will be charged for each replacement unit.
WARNING - READ CAREFULLY
Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring
each item in this warning to the attention of the users of this system.
System Failures
This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire,
burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be com-
promised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be:
Inadequate Installation
A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated
by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors
must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient
strength and construction to provide the level of protection expected. A reevaluation must be done during and after any con-
struction activity. An evaluation by the fire and/or police department is highly recommended if this service is available.
Criminal Knowledge
This system contains security features which were known to be effective at the time of manufacture. It is possible for persons
with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security sys-
tem be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it
does not provide the protection expected.
Access by Intruders
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through
an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system.
Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for
proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed,
they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, how-
ever brief, will render that device inoperative while it does not have power. Power interruptions of any length are often
accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power inter-
ruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.
Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The
expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high
or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device
- 289 -
has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expec-
ted. Regular testing and maintenance will keep the system in good operating condition.
Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio
path or deliberate jamming or other inadvertent radio signal interference.
System Users
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability,
inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained
in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm.
Smoke Detectors
Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of
which follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the
smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors
may not detect smoke from fires on another level of the residence or building.
Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of
fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such
as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits,
children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all
occupants to escape in time to avoid injury or death.
Motion Detectors
Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions.
They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area pro-
tection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these
beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or
windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material
on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced
when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of
heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbeques, fireplaces,
sunlight, steam vents, lighting and so on.
Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an inter-
vening wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that
the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as
stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud,
may not be heard by a hearing-impaired person.
Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder
may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect.
Insufficient Time
There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the
emergency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may
not occur in time to protect the occupants or their belongings.
Component Failure
Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended
due to the failure of a component.
Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be found by regular testing and main-
tenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a
storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should
- 290 -
include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of
the system.
Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a
substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an
emergency situation.
IMPORTANT - READ CAREFULLY:
DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following
license terms:
l This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity
who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety
Products Canada Ltd. (“DSC”), the manufacturer of the integrated security systems and the developer of the software
and any related products or components (“HARDWARE”) which You acquired.
l If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by
HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE
PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed
materials, and “online” or electronic documentation.
l Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license
agreement is licensed to You under the terms of that license agreement.
l By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree
unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any pre-
vious arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the
SOFTWARE PRODUCT to You, and You have no right to use it.
8.0 SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual
property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE
PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used con-
currently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In
other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE
will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per
license installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly
provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials
accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or dis-
assemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable
law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written per-
mission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You
shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be
separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT
is licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used
with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on
a server or web site.
- 291 -
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or trans-
fer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all com-
ponent parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms
of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the
SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and
conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component
parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its
suppliers.
3. COPYRIGHT
All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, pho-
tographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the
SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the
SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of
the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright
or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly
granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS
You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Cana-
dian export restrictions.
5. CHOICE OF LAW
This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION
All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance
with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be
Toronto, Canada, and the installation manual of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT
THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the oper-
ating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-
SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE
IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY
UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT
ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00).
BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF
ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR
LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS
WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE
PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES
INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED
EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES,
DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO
- 292 -
PROPERTY.
WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent test-
ing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to
fail to perform as expected.
- 293 -
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any mis-
use of the trademarks is strictly prohibited and Tyco will aggressively enforce its intellectual property rights to the fullest extent of the
law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco are the property of their respect-
ive owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products
include all features. Availability varies by region; contact your sales representative.
© 2018 Tyco Security Products

All Rights Reserved.
Tech Support: 1-800-387-3630 (Canada & U.S.)
or 905-760-3000
www.dsc.com 29010134R005

PowerSeries Pro V1.1 Reference Manual 29010134R005 en

Uploaded by

Copyright:

Available Formats

PowerSeries Pro V1.1 Reference Manual 29010134R005 en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PowerSeries Pro V1.1 Reference Manual 29010134R005 en

Uploaded by

Copyright:

Available Formats

intrusion

PowerSeries Pro Alarm Controller

Features HS3032 HS3128 HS3248

*For UL installations, 2 repeaters must be installed for proper signal routing.

Table 1-2 Compatible devices

PowerG wireless glassbreak detector PGx912/PGx922 UL

2.2 Alarm controller installation

Mounting the enclosure

Figure 2-2 HSC3010C, HSC3010CR, HSC3030CAR enclosures

Wall mounting the HSC3020C enclosure

A Tamper mounting location.

Figure 2-4 HSC3020CP enclosure

HSM3408 in HSC3010 enclosure

Figure 2-6 HSM3408 in HSC3010C enclosure

HSM3408 and HSM3350 mounting in HSC3020C enclosure

HSM2108/HSM2208 mounting locations in HSC3010 enclosure

2.3 General wiring instructions

For HSC3010C installations, complete the following steps:

HS3032/HS3128/HS3248 in HSC3020C NA Wiring Diagram

Cable tie required

Cable tie required

For HSC3020C installations, complete the following steps:

Installing the HSM3204CX in HSC3010C enclosure

1. Insert standoff into cabinet

Primary: 120VAC, 60Hz, Class VI

Plastic grommet strip (Not supplied) recommmended

Note: Power supply may be mounted outside the

HSM3204CX in HSC3020C North American wiring diagram

Tamper switch and

1. Insert standoff into cabinet

Cable tie required

Cable tie required

Installing the HSM3350 in the HSC3010C enclosure

1. Insert standoff into cabinet

Primary: 120VAC, 60Hz, Class VI

Plastic grommet strip (Not supplied) recommmended

Note: Power supply may be mounted outside the

North American wiring for HSM3350 in the HSC3020C enclosure

Cable ties (not supplied) recommended

Tamper switch and

1. Insert standoff into cabinet

Cable tie required

Cable tie required

Installing the HS3032/HS3128/HS3248 in the HSC3020C enclosure

Cable ties (not supplied) recommended STANDOFF

1. Insert standoff into cabinet mounting hole in the

1X18Ah/12V sealed lead

Replace fuse with same type (20 mm) rated

For HSC3020C installations, complete the following steps:

HSM3204CX in HSC3020CP wiring diagram

HSM3350 in HSC3020CP international wiring diagram

EGND Earth ground connection

*x= none use for CE/EN certified applications

Wire routing for power & non-power limited

Alarm controller current calculation

PCLink+ (200 mA)

USB (500 mA max.)

Cell module (20 mA idle)

Total (must not exceed 2 A)

Night Arm when armed in stay mode [][1] + [Access Code]