User’s

Manual
STARDOM
Plant Resource Manager

IM 34P02Q52-01E

IM 34P02Q52-01E
14th Edition
Blank Page
 i

Introduction
 About this manual
This manual describes precautions for the use of Plant Resource Manager (hereinafter,
PRM) to operate STARDOM.

Refer to "Plant Resource Manager Installation" (IM 33Y05Q12-11E) for the procedure
for installing the PRM package on a PC and its settings.

Refer to "Plant Resource Manager Reference" (IM 33Y05Q10-11E) for device

management, management of the history of device operation, adjustment and
diagnostic functions performed by PRM.

 Related documents
• STARDOM IT Security (IM 34P02Q93-01E)
• Plant Resource Manager Reference (IM 33Y05Q10-11E)
• Plant Resource Manager Installation (IM 33Y05Q12-11E)

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 ii

Safety Precautions
 Important information about this manual
(1) Please ensure that end users receive this manual.
(2) Carefully read this manual and make sure you understand its contents before
operating the product.
(3) This manual provides a detailed description of the functions in the product, but it is
not intended as a guarantee of suitability for specific user objectives.
(4) Unauthorized transfer or reproduction of all or part of this manual is strictly
prohibited.
(5) The contents of this manual may be changed without notice in the future.
(6) Please contact our sales department or the dealer where you made your purchase
if you have any questions about the information in this manual, or if you discover
any errors, omissions, or the like.

 Important information regarding product protection, safety, and

modifications
(1) Follow the product safety instructions when handling the product in order to ensure
safety and protect the product and systems controlled by the product. Yokogawa
cannot guarantee safety if the product is handled in a manner which violates these
instructions.

This label means "handle with caution”. It is attached in locations on the product
that need to be referenced in the user's manual to ensure personal safety and
protect the equipment. In addition, the user's manual contains cautions for
avoiding danger in cases where there are possible hazards which could result in
death or injury (e.g., electric shock).

This label represents a protective ground terminal. Be sure to ground this terminal
before operating the equipment.

This label represents a functioning ground terminal. Be sure to ground this terminal
before operating the equipment.

This label represents the power switch ON state.

This label represents the power switch standby state.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 iii

This label represents the power switch OFF state.

(2) If you wish to install a protector/safety circuit on this product or a system to be used
by this product, please install it outside of this product.
(3) When replacing components or consumables in the product, be sure to use the
products specified by Yokogawa.
(4) Modification of this product is strictly prohibited.

 Limitations of product liability

(1) Yokogawa provides no guarantees with respect to this product except if established
in the terms of a warranty.
(2) Yokogawa assumes no liability in cases where the customer or a third party suffers
damages as a result of using this product, or with respect to damages suffered by
the customer or a third party or any indirect damages resulting from, for example,
defects in the product which could not have been predicted by Yokogawa.

 This software
(1) Yokogawa provides no guarantees with respect to this software except if
established in the terms of a warranty.
(2) Use this software on a single, specified computer. If you wish to use the software
on another computer, please separately purchase the software for that computer.
(3) Copying of this software for purposes other than backups is strictly prohibited.
(4) Store the original disks (DVD-ROM and CD-ROMs) which contains the software in a
safe place.
(5) Reverse compiling, reverse assembly, and the like (reverse engineering) with
respect to this software are strictly prohibited.
(6) Allowing a third party to use all or part of this software, by means of transfer,
exchange, rental, or the like without the prior approval of Yokogawa is strictly
prohibited.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 iv

Conventions Used in This Manual

 Symbols and typographic marks in the manual
The symbols and typographic marks appearing in the user's manual have the meanings
shown below.

 Symbols and typographic marks used throughout the manual

Text enclosed in angle brackets
When you click a character string enclosed in angle brackets in the online manual, the
screen jumps to the corresponding location in the manual.
Example
<Table of Contents> <Index>
Input character string
Character strings in the following format denote information that is input by the user in
an actual operation.
Example
FIC100.SV=50.0
“△” symbol
This symbol denotes a blank character (space) in a character string entered by the user.
Example
. AL△PIC010△-SC
Text enclosed in curly brackets
Curly brackets are used to denote a character string that can be omitted from the
character string entered by the user.
Example
. PR△TAG｛△.sheet name｝

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 v

 Typographic marks used in explanations of key and button operations

Text enclosed in square brackets
Square brackets are used to denote keyboard keys, window button names, and items
appearing in a window in descriptions of key and button operations.
Example
Press the [ESC] key to switch functions.

 Typographic marks and symbols used in syntax explanations

(command
text, program text, etc.)
Typographic marks and symbols are used in command text, program text and the like
with the following meanings.
Text enclosed in angle brackets
Angle brackets are used to denote a character string that can be specified as desired by
the user in accordance with fixed rules.
Example
#define ＜identifier＞ ＜text string＞
“…” symbol
This symbol indicates that the preceding command or argument can be repeated.
Example
GetPropertyEx(PropName As String, List1 [, List2, ...] As Integer) As Variant
Text enclosed in square brackets
Square brackets indicate a character string that can be omitted.
Example
SetCv(NewValue As Variant,[Transaction ID As Long])
Text enclosed in vertical lines
Vertical lines are used to indicate character strings that can be selected as desired by
the user from a number of character string options.
Example
X
Move XY
Y

 Text conventions in the Windows screens

 Menu bar menus, commands, text box names, and buttons are
enclosed
in square brackets.
Example: From the menu bar, select [Icon (E)] - [Specify file and run (F)].
(The meaning is to select [Icon (E)] from the menu bar, then select [Specify file and run
(F)] from the pulldown menu.)

 Quotation marks are used to enclose the names of groups, icons,

windows, and dialog boxes.
Example: Double-click “Manual Viewer” in the “System Launcher” group.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 vi

 Symbol marks
The symbols marks appearing in this manual have the meanings shown below.

CAUTION
This symbol means “handle with caution”.
The user's manual contains cautions for avoiding danger in cases where there are
possible hazards which could result in death or injury (e.g., electric shock).

WARNING
This symbol means “warning”.
Information under this label relates to important issues in cases where there is a risk
that the software or hardware could be damaged, or system problems could occur.

IMPORTANT
This symbol means “important”.
Information under this label relates to important issues in terms of understanding
operations and functions.
TIP
Additional explanatory information is presented under this label.
SEE ALSO
Reference items are presented under this label.
In cases where the reference item is displayed in green, you can click it to display
the reference material.
In cases where the reference item is displayed in black, you cannot click it to
display the reference material.

 Diagram notation
The diagrams presented in this manual may be enhanced, simplified, or only displayed
in part in order to make the explanations easier to understand.
The screenshots in this manual may differ from the actual screen displays in terms of
display location and fonts (e.g., large/small fonts). Any differences are not significant
enough to impede understanding of the functions and operating monitoring.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

 vii

Copyrights and Trademarks

 Copyrights
Copyrights for the program, online manual, and the like contained on the original disks
(DVD-ROM and CD-ROMs) are the property of Yokogawa.
The online manual has PDF security settings that prevent its contents from being
overwritten. A hard copy of the manual may be printed on a printer.
If you plan to use a printed hard copy of the online manual, please use it only for the
purpose of using this product. Also, when using a hard copy, take care to ensure that
there are no inconsistencies between the hard copy and the latest version of the
manual. Make sure that the version number is the same as the version of the most
recent original disks (DVD-ROM and CD-ROMs).
Copying of the online manual, as well as transferring, selling, and distributing it to third
parties (including providing it online through a PC communication network) are
prohibited. Furthermore, unauthorized registration and recording onto videotape or the
like are prohibited.

 Trademarks and licensed software

• STARDOM is a trademark of Yokogawa Electric Corporation.
• PRM is a registered trademark of Yokogawa Electric Corporation in the United
States and Japan.
• Microsoft and Windows are trademarks or registered trademarks of Microsoft
Corporation in the US and other countries.
• Adobe, Adobe Acrobat, and Adobe Reader are trademarks or registered
trademarks of Adobe Systems Incorporated in the US and other countries.
• Ethernet is a registered trademark of Xerox Corporation.
• The “FOUNDATION” part of FOUNDATION fieldbus is a registered trademark of
the Fieldbus Foundation.
• Other company names and product names appearing in this document are
trademarks or registered trademarks of their respective companies.
• In this document, the ™ and ® marks are not shown next to the registered
trademarks or trademarks of their respective companies.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

Blank Page
 ix

STARDOM
Plant Resource Manager
IM 34P02Q52-01E 14th Edition

CONTENTS
Introduction .................................................................................................. i
Safety Precautions ..................................................................................... ii
Conventions Used in This Manual ............................................................. iv
Copyrights and Trademarks...................................................................... vii
CONTENTS ............................................................................................... ix
1. Overview ............................................................................................ 1
2. Precautions for System Configuration ................................................ 3
3. Precautions for Installation ................................................................. 5
3.1 Cautions for installing FCN/FCJ OPC Server for Windows
on the same PC with PRM ............................................................................9
3.2 Setup after installing the FCN/FCJ OPC Server for Windows .....................10
3.2.1 Setting up for remote access .........................................................10
3.2.2 HDA server startup settings ...........................................................10
3.2.3 Message collection destination definition ....................................... 11
3.2.4 HDA server settings .......................................................................12
Revision Information .................................................................................... i

IM 34P02Q52-01E14th Edition :Apr 28, 2016-00

Blank Page
 <1. Overview > 1

1. Overview
This manual describes precautions for the use of Plant Resource Manager
(hereinafter, PRM) to operate STARDOM.
The precautions are as follows:
1. Precautions for System Configuration
2. Precautions for Installation
For other than the above, refer to the following:

• STARDOM IT Security (IM 34P02Q93-01E)

This manual is a guide for implementing security in the STARDOM system
from the viewpoint of Information Technology (IT).
• Plant Resource Manager Installation (IM 33Y05Q12-11E)
This manual describes the procedure for installing the PRM package on a PC
and its settings.
• Plant Resource Manager Reference (IM 33Y05Q10-11E)
This manual describes device management, management of the history of
device operation, adjustment and diagnostic functions performed by PRM.

 Operating Environment
This manual refers to the following operating environments:
Table Operating Environment
System Revision
PRM R3.30
FCN/FCJ OPC Server for Windows R4.02

Note: PRM and FCN/FCJ OPC Server for Windows can only be used in combination with respective revisions specified in
the table.

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

Blank Page
 <2. Precautions for System Configuration > 3

2. Precautions for System Configuration

Following must be considered when connecting STARDOM to PRM.

 Device Tag name

Device Tag name on Fieldbus device must be unique names within the range managed
by PRM Server.
Generally, PRM Server and PRM Field Communication Server are installed separately
for each control network. Unique device tag must be set on all of the connected
Fieldbus device.
Each block tag name must be unique within the FCN/FCJ system.

TIP
• The FOUNDATION fieldbus described in this manual is a "FOUNDATION fieldbus H1," as
standardized by the Fieldbus Foundation.
The term "FOUNDATION fieldbus" is used to denote the "FOUNDATION fieldbus H1."
• The term "Fieldbus device" used in this manual to refer to a field device connected to a
FOUNDATION fieldbus.

 Messages
The format of alerts generated from Fieldbus device differs in VDS and PRM. In VDS,
only important information is shown due to message length limitations. However, in
PRM, all information in alert messages is shown.
Likewise, alerts generated from a given piece of Fieldbus device appear differently in
PRM depending on whether the Fieldbus device is connected to STARDOM or to
CENTUM.

 Time synchronization
In the CENTUM VP/CS 3000 system, the Field Communication Server time can be
synchronized with the Vnet time. To enable time synchronization in STARDOM, set the
PC so that clocks are synchronized by SNTP.

SEE ALSO
For details, see the "net time" command Help topic in Windows. Also see the STARDOM Network
Configuration Guide (TI 34P02K25-01E).

 Maximum number of connected units

The maximum number of connected FCN/FCJ units supported by Field Communication
Server is 100 in both cases.
In large-scale systems, use the multi-server function to divide the connected controllers
being managed by PRM Server into groups of 100 or fewer units.

IM 34P02Q52-01E12th Edition : Jun. 29, 2012-00

Blank Page
 < 3. Precautions for Installation > 5

3. Precautions for Installation

It is recommended that FCN/FCJ OPC Server for Windows is installed on the
different PC from one with PRM.

TIP
PRM components and the FCN/FCJ OPC Server for Windows can be installed on the same PC with
several limitations.

SEE ALSO
When installing FCN/FCJ OPC Server for Windows on the same PC with PRM, see 3.1 "Cautions for
installing FCN/FCJ OPC Server for Windows on the same PC with PRM" in this manual.

An example system configuration and installation procedure are provided below.

 Example System Configuration

Figure Example system configuration for installing PRM components and FCN/FCJ OPC
Server for Windows on the different PCs

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 6

 Installation on the different PCs (Overview)

See 2.1 "Preparation before installation" and 2.2.1 "Checking the

Start operating environment for the necessary hardware and software" in
"Plant Resource Manager Installation" (IM 33Y05Q12-11E)

This step is not required if you are using a recommended PC in

Install Windows which Windows is already installed .

This step is not required if you are using a recommended PC in

Install Windows Service Pack which Windows Service Pack is already installed .

Prepare for installation See 2.2.2 "Checking Windows settings" in "Plant Resource Manager
(Set up Windows) Installation" (IM 33Y05Q12-11E)

See 2.2.3 "Installing and configuring drivers " in "Plant Resource

Install drivers Manager Installation" (IM 33Y05Q12-11E)

Reinstall Windows Service Pack

See 3.1 "New installation of PRM" in "Plant Resource Manager

Install PRM packages Installation" (IM 33Y05Q12-11E)

See 3.2 "Configuration of security settings" in "Plant Resource

Configure security settings Manager Installation" (IM 33Y05Q12-11E)

See 5.2.8 "Configuring OPC Clients" in "STARDOM IT Security" (IM

Configure OPC Clients 34P02Q93-01E)

See 5.2.2 "Configuring Environment before Installation " to 5.2.7

Install the FCN/FCJ
"Configuring Duplexed Network Function " in "STARDOM IT Security" (IM
OPC Server for Windows 34P02Q93-01E)

Setup after installing the FCN/FCJ See 3.2 “Setup after installing the FCN/FCJ OPC Server for Windows” in
OPC Server for Windows this manual

Collaboration with PRM See 5.3.2 "Collaboration with PRM" in "STARDOM IT Security" (IM
Configuration on OPC Server side 34P02Q93-01E)

Procedure on the OPC server PC

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 7

See 3.3 "Setup of PRM after installation" in "Plant Resource Manager

Setup after installation Installation" (IM 33Y05Q12-11E)
・ Start the PRM Setup Tool See 3.3.1 "Starting the PRM Setup Tool"

・ Set up the PRM Server See 3.3.2 "Setting up the PRM Server"

・ Set up the Field Communications Server See 3.3.3 "Setting up the Field Communications Server "

・ Set up the PRM Client See 3.3.4 "Setting up the PRM Client"

Install and register PLUG-IN See F3.1 "Working with PLUG-IN applications" in "Plant Resource
applications Manager Reference" (IM 33Y05Q10-11E)

End : Must be performed : Performed if necessary

: Must be performed, but must not be performed in the case of installation on the same PC

Figure Procedure for installing PRM components and FCN/FCJ OPC Server for Windows on
the different PCs

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 8

 Installation on the same PC (Overview)

See 2.1 "Preparation before installation" and 2.2.1 "Checking the

Start operating environment for the necessary hardware and software" in
"Plant Resource Manager Installation" (IM 33Y05Q12-11E)

This step is not required if you are using a recommended PC in

Install Windows which Windows is already installed .

This step is not required if you are using a recommended PC in

Install Windows Service Pack which Windows Service Pack is already installed .

Prepare for installation See 2.2.2 "Checking Windows settings" in "Plant Resource Manager
(Set up Windows) Installation" (IM 33Y05Q12-11E)

See 2.2.3 "Installing and configuring drivers " in "Plant Resource

Install drivers Manager Installation" (IM 33Y05Q12-11E)

Reinstall Windows Service Pack

See 3.1 "New installation of PRM" in "Plant Resource Manager

Install PRM packages Installation" (IM 33Y05Q12-11E)

See 5.2.2 "Configuring Environment before Installation " to 5.2.7

Install the FCN/FCJ
"Configuring Duplexed Network Function " in "STARDOM IT Security" (IM
OPC Server for Windows 34P02Q93-01E)

Setup after installing the FCN/FCJ See 3.2 “Setup after installing the FCN/FCJ OPC Server for Windows” in
OPC Server for Windows this manual

Add PRM_PROCESS to the See "Installation Procedure" of 5.4.2 "Installing on the Same PC as PRM"
STM_OPC group in "STARDOM IT Security" (IM 34P02Q93-01E)

See 3.3 "Setup of PRM after installation" in "Plant Resource Manager

Setup after installation Installation" (IM 33Y05Q12-11E)
・ Start the PRM Setup Tool See 3.3.1 "Starting the PRM Setup Tool"

・ Set up the PRM Server See 3.3.2 "Setting up the PRM Server"

・ Set up the Field Communications Server See 3.3.3 "Setting up the Field Communications Server "

・ Set up the PRM Client See 3.3.4 "Setting up the PRM Client"

Install and register PLUG-IN See F3.1 "Working with PLUG-IN applications" in "Plant Resource
applications Manager Reference" (IM 33Y05Q10-11E)

End : Must be performed : Performed if necessary

: Must be performed except the case of installation on the different PCs

Figure Procedure for installing PRM components and FCN/FCJ OPC Server for Windows on
the same PC

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 9

3.1 Cautions for installing FCN/FCJ OPC Server

for Windows on the same PC with PRM
 Limitations

 Compatibility
If you want to install FCN/FCJ OPC Server for Windows on a PC installed with PRM,
refer to the revision combination in the following table. If there are other combinations,
then FCN/FCJ OPC Server for Windows must be installed on a separate PC.
Table Compatibility
FCN/FCJ OPC Server for Windows PRM
Revision R1.90 R3.02
R2.20 R3.03, R3.04
R3.01 R3.05
R3.10 R3.05
R3.20 R3.11
R3.30 R3.11
R3.40 R3.11
R3.50 R3.20, R3.30
R4.02 R3.20, R3.30

 Operating environment
The PC needs to meet with the PRM and FCN/FCJ OPC Server for Windows
specifications.

SEE ALSO
• For PRM, see 1.1.2 "Software requirements" in "Plant Resource Manager Installation" (IM
33Y05Q12-11E).
• For FCN/FCJ OPC Server for Windows, see " SYSTEM REQUIREMENTS" in "STARDOM
FCN/FCJ OPC Server for Windows" (GS 34P02Q61-01E).

 Security model
When installing PRM, specify the "Legacy Model - Standalone Management" or
"Standard Model - Standalone Management" for the security setting.

 Uninstallation and upgrade

When upgrading PRM or FCN/FCJ OPC Server for Windows on the same PC, uninstall
PRM, Exaopc and FCN/FCJ OPC Server for Windows in that order, then install new
software by following installation procedure.

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 10

3.2 Setup after installing the FCN/FCJ OPC

Server for Windows
To install FCN/FCJ OPC Server for Windows, do the following:
1. Setting up for remote access
2. HDA server startup settings
3. Message collection destination definition
4. HDA server settings

3.2.1 Setting up for remote access

If you want to use DCOM, please setup as follows:

1. Run Administrative Tools.

2. Choose the [Local Security Policy] → [Local Policies] → [Security Options].
3. Choose the "Network access: Sharing and Security model for local accounts".
4. Show property on right click, and change property to "classic-local users
authenticates themselves".

3.2.2 HDA server startup settings

OPC HDA server must be started when using PRM. After installing FCN/FCJ OPC
Server for Windows, use the following procedure to enter a definition for starting OPC
HDA server.

1. Open %Installation drive%:\EXA\Config\Service\ExaopcDASTRDOMFCX.HIS in a

text editor such as Notepad.
2. Find the following line containing ZOPHDA.EXE. Remove the pound sign (#) at the
beginning of the line.
#1117::ZOPHDA.EXE /C STARDOMFCX:NORMAL:HIDE:0:113:::
↑ Remove this pound sign
3. Save the edited file.

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 11

3.2.3 Message collection destination definition

The FCN/FCJ to be used for message collection must be defined in advance when
using PRM. After installation, use the following procedure to define the FCN/FCJ.

1. Open %Installation Folder%\Config\fcxcnf.csv in a text editor such as Notepad.

2. Set node identifiers and FCN/FCJ host addresses in the following format on the
lines from [Node] onward.
Node identifier, FCN/FCJ host address (host name or IP address)

IMPORTANT
• The Node identifier is a character string not including ".", "!", or ",", and setting shall
be done so that there is no duplication.
There are two FCN/FCJ, and when each FCN/FCJ host address is 192.168.0.1 and
192.168.0.2, the example.
FCN01, 192.168.0.1
FCN02, 192.168.0.2
• IP addresses are entered in decimal dot notation.

3. Save the edited contents.

4. Restart the system.

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 < 3. Precautions for Installation > 12

3.2.4 HDA server settings

The default values for settings related to HDA server are set during FCN/FCJ OPC
Server for Windows installation. For connection with PRM, enter the following command
and set the values shown below in the Exaopc Setup Window.
%Installation drive%:\EXA\Program\ZOCSet
After changing the settings, reboot the system.
Table HDA server settings
Item Setting Remarks
Historical Scope of Keeping All －
Event Number of 10000 －
Records
Current Cassette HDASTARDOMFCX －
Permanent Save Folder %Installation drive% : \EXA\Save －

Fig. Exaopc Setup Window

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 i

Revision Information
Title : STARDOM Plant Resource Manager
Manual No. : IM 34P02Q52-01E

Jan. 2004/1st Edition/R1.40 or later

• Newly published

Oct. 2004/2nd Edition/R1.50 or later

• Duplexing the NFLF111 was supported.

Apr. 2005/3rd Edition/R1.60 or later

• Correspondence to PRM R2.06.
• The installation procedure of Oracle 10g has been added.
• Errors were corrected.

Aug. 2005/4th Edition/R1.70 or later

• A TIP has been added to “FCN/FCJ OPC Server Setup”.

Feb. 2006/5th Edition/R1.80 or later

• Correspondence to PRM R2.20.
• Deleted "■ Device path configuration definition procedure" in "2.3.2.Device Path Configuration on
Field Communication Server".

Aug. 2006/6th Edition/R1.85 or later

• Modified "Fig. Procedure for installing all PRM components and FCN/FCJ OPC Server for Windows
on the same PC ".

Jan. 2007/7th Edition/R1.86 or later

• Completely revised for compatibility with PRM R3.01.

May. 2008/8th Edition/R2.01 or later

• Correspondence to PRM R3.02.

Aug. 2009/9th Edition/R2.20 or later

• Correspondence to PRM R3.03.

Jun. 2010/10th Edition/R3.01 or later

• Correspondence to PRM R3.05.

Mar. 2011/11th Edition/R3.10 or later

• Table of Compatibility is updated.
• Errors were corrected.

Mar. 2012/12th Edition/R3.20 or later

• Table of Compatibility is updated.
• Modified "Figure Procedure for installing PRM components and FCN/FCJ OPC Server".

May 2015/13th Edition/R3.50 or later

• Table of Compatibility is updated.

Apr 2016/14th Edition/R4.02 or later*

• Correspondence to PRM R3.30.

*: Denotes the release number of the software corresponding to the contents of this instruction manual. The
revised contents are valid until the next edition is issued.

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00

 ii

■ For Questions and More Information

If you have any questions, you can send an E-mail to the
following address.
E-mail:[email protected]
■Written by Yokogawa Electric Corporation
■Published by Yokogawa Electric Corporation
2-9-32Nakacho, Musashino-shi, Tokyo 180-8750, Japan

IM 34P02Q52-01E14th Edition : Apr 28, 2016-00