Preschool Exercises PDF

Sedco Forex
Jakarta Learning Centre
Pre-school exercises for Well Control
With Answers.
Pre-School Well Control exercises 27/07/99
Contents.
Introduction ............................................................................................................................................ 3
Section A
Well Control Equipment ........................................................................................................................ 4
Section B
Pre-recorded information..................................................................................................................... 14
Section C
Causes of kicks...................................................................................................................................... 18
Section D
Indications of a kick ............................................................................................................................. 21
Section E
Shut-in Procedure................................................................................................................................. 25
Section F
Kick Data.............................................................................................................................................. 28
Answers................................................................................................................................................. 59
Formulae for Well Control................................................................................................................... 67
Page 2 of 69
Introduction.
Pre-School exercises for Well Control
This book of exercises is designed to help you prepare for well control school. The exercises
were written to provide up to date questions for self-study either on the rig or at home.
Answers are provided for all the questions at the back of the book.
Please bring this book with you to well control class if there is anything that you would like to
discuss.
Page 3 of 69
Section A
Well Control Equipment
A1 Blowout Preventers and Diverters.
1) Indicate the activities that may be carried out wih the BOP stack shown below.
a) With no drill pipe in the hole, shut in the well under pressure and repair the spool.
b) With drill pipe in the hole, shut the well in and change pipe rams to blind rams.
c) With drill pipe in the hole, circulate through the drill pipe.
d) With drill pipe in the hole, shut in the well under pressure and repair the side outlets on the
spool .
Annular
Blind
Spool
Kill Choke
Pipe
2) What is the primary function of the weep hole (drain hole, vent hole) on a ram type BOP?
a) To show that ram body rubber is leaking.

b) To show that the primary mud seal on the piston rod is leaking.
c) To show that the Bonnet seals are leaking.
d) To show that the closing chamber operating pressure is too high.
3) You only have one inside BOP with an NC 50 (4”1/2 IF) lower pin connection on your rig
but the drill string consist of 5” HWDP, and 8” collars. Which one of the following crossovers
would you have on the drill floor in case of kick while tripping?
a) 6-5/8” reg. Box X 7-5/8” reg. Pin

b) NC50 (4-1/2” IF) Pin X 6-5/8” reg. Pin
c) NC50 (4-1/2” IF) Box X 7-5/8” reg. Pin
d) NC50 (4-1/2” IF) Box X 6-5/8” reg. Pin
Page 4 of 69
4) Two types of valves may be used in the drill string:
Type 1 Non return, stab in safety valve or inside BOP

Type 2 Fully opening stab in Kelly cock valve or fully opening safety valve
Indicate in the table which statement describes the valves.
Type 1 Type 2
Requires the use of key to close
Must not run in the hole in the close position
Has to be pumped to read “shut-in drill pipe pressure”
Will not allow wireline to be run inside the drill string
Has potential to leak through the open/close key
Easier to stab if strong flow is encountered up the string
5) A BOP stack is configured: Pipe ram / Blind-Shear ram / Pipe ram / Annular, kill and choke
lines are connected under the blind-shear rams. Is it possible to kill a well using the Driller's
method if;
a) The upper pipe rams are closed?

b) The blind shear rams are closed?
c) The lower pipe rams are closed?
6) A BOP stack is configured: Pipe ram / pipe ram / Blind-Shear ram / Annular, kill and choke
lines are connected under the blind-shear rams.
a) Can you repair the side outlets with pipe in the hole?
b) Can you repair the outlets with no pipe in the hole?
c) Is it possible to shut in with drill pipe in the hole and
circulate through the drill pipe?
d) Can you change blind rams to pipe rams and kill the well?
7) A BOP stack is configured: Drilling spool / Pipe ram / Blind-Shear ram / Annular, kill and
choke lines are connected to the drilling spool.
a) With drill pipe in hole, can we repair the side outlets?

b) With no drill pipe in the hole, can you shut in and repair the Drilling spool?
c) With drill pipe in hole, can you circulate through the Drilling spool?
8) The kill line should enter a stack so that
a) The well can be circulated if the blind rams are in use.

b) The well can be circulated if the pipe rams are being used.
c) Both the above.
9) Which of the following statements are true concerning Ram Packing Elements?
Page 5 of 69
a) Reciprocating motion of the pipe increases the wear on seals.

b) Closing pipe rams on open hole may damage the elements.
c) The ram packer should normally be checked, and if worn, changed whenever the bonnet is
opened.
d) All of above.
10) What do the term “6BX” stamped on a flange represent?
a) serial number
b) pressure rating
c) type
d) size
11) What is meant by the closing ratio for a ram type BOP?
a) Ratio between closing & opening volume.

b) Ratio between closing & opening time.
c) Ratio of the wellhead pressure to the pressure required to close the BOP.
12§) Which option gives the advantage of using the kill line with static fluid to monitor well
head pressure during a well kill operation?
a) Response on changes in well head pressure is quicker through the kill line.
b) Effect of choke line friction is reduce to ¼ when monitoring on kill line gauge during the
kill operation.
c) Effect of choke line friction is reduced to ½ when monitoring on kill line gauge during the
kill operation.
d) The kill line pressure can be kept constant while changing the pump speed, thus eliminating
the need to compensate for CLFL.
13) Study the two tables below which contain markings stamped on API flanges and ring
gaskets. Each flange (1,2,3 and 4) mates with one of the ring gaskets (A,B,C or D). Write the
appropriate flange number in the blanks.
Ring Gasket Marking Flange
A CI API BX154 S304-4
B OES API R57 D-4
C OES API RX66 S-4
D CI API BX153 S316-4
Flange Marking
1. OES API 16-3/4 3M RX66 6A 89 300F PSL3 05/91
2. CI API 3-1/16 15M BX154 CRA 6A 89 250F PSL2 PRL2 08/92
3. OES API 2-9/16 20M BX153 CRA 6A 89 350F PSL4 PRL4 01/94
4. OES API 13-5/8 2M R57 6A 89 250F PSL1 PRL1 11/93
14) Write the pressure rating, bore diameter and temperature rating of each flange in the
previous question, in the blanks below.
Page 6 of 69
Flange#1___________psi __________ inches __________ deg.F

15) Identify the one ram locking device from the list below that locks the ram in the same
position regardless of wear.
a) Shaffer “Ultralock”
b) Shaffer “Poslock”
c) Hydril “MPL”
d) Cooper(Cameron) “Wedgelock”
e) Koomey “Autolock”
16) From the list below, identify the ring gaskets that are pressure energized. (Pick four
answers)
a) Type RX
b) Type BX
c) Type AX
d) Type R oval
e) Type R octagonal
f) Type CX
17) Which dimension from the list below is used to identify the “Nominal Flange Size” (Pick
one answer).
a) Throughbore I.D.
b) Flange O.D.
c) Diameter of raised face.
d) O.D. of ring groove.
e) Bolt circle diameter.
18) What is the main function of a diverter?
a) To shut in a shallow kick.

b) To direct fluid a safe distance away from the rig floor.
c) To create a back pressure sufficient to stop formation fluids entering the wellbore.
d) To act as a back up system if the annular preventer fails.
Page 7 of 69
19) In an area where local legislation requires that BOP equipment must be rated so that
maximum anticipated formation pressures do not exceed 75% of BOP equipment pressure
ratings, what is the minimum acceptable rating for equipment to be used in drilling normally
pressure formation to 16000 ft TVD?
a) 2000 psi BOP equipment

b) 3000 psi BOP equipment
c) 5000 psi BOP equipment
d) 10000 psi BOP equipment
e) 15000 psi BOP equipment
20§) What is normally considered the highest potential risk when diverting a shallow gas
blowout through a long marine riser?
a) The marine riser may collapse.

b) The marine riser may burst from the excess pressure exerted by the gas inside the riser.
c) Buoyancy forces acting on the marine riser may require riser tension forces in excess of
situation where the riser is full of drilling fluid.
A2 BOP control systems
1) A BOP stack is configured Pipe Ram / Blind-Shear ram / Pipe Ram / Annular. Use the table
below to calculate the required accumulator volume if company policy is to provide sufficient
volume to close, open and close again all rams and the annular.
Component Volume to Open Volume to close

Annular BOP 27 29
Ram BOP 13 15
2) The following statements relate to the driller’s remote control BOP control panel located on
the rig floor. Decide if the statements are true or false.
a) If you operate a function without operating the master control valve that function will not
work.
b) The master control valve on an air operated panel allows air pressure to go to each
function in preparation for you operating the function.
c) The master control valve must be held depressed while BOP functions are operated.
d) The master control valve must be depressed for five seconds then released before operating
a BOP function.
3) The API RP53 states that closing time should not exceed X seconds for annular BOPs
smaller than 18-3/4". What is the value of X?
a) 30 sec.
b) 60 sec.
c) 2 min.
d) 45 sec.
4) Which is the correct definition of the HPU reservoir volume according to API RP53?
Page 8 of 69
a) 2 times usable accumulator volume.

b) 2 times accumulator volume.
c) 5 times total accumulator volume .
5) Which two pressure readings decrease during normal operation of the pipe rams?
a) Manifold pressure
b) Annular pressure
c) Accumulator pressure
d) Precharge pressure
6) When closing the annular preventer from the remote panel, which two gauges show a
reduction in pressure?
a) Manifold pressure
b) Annular pressure
c) Accumulator pressure
d) Air pressure
e) Bypass pressure
7) In each of the cases below, identify the most likely problem from the gauge readings
observed on the remote control panel. The annular setting is 900 psi, the manifold setting is
1,500 psi.
a) Everything is OK.
b) Malfunction pressure regulating valve.
c) Malfunction hydro-electric switch
d) Leaking in hydraulic circuit
e) Precharge pressure is to low
Accumulator Manifold Annular Problem

pressure pressure pressure
(i) 2,900, 1,500, steady 900 steady
increasing
(ii) 2,700 1,800 steady 900 steady
increasing
(iii) 2,400 1,300 steady 900 steady
increasing
(iv) 3,300 1,500 steady 900 steady
increasing
8) A BOP operating unit has 8 accumulator bottles, each with a capacity of 10 gallons.
Operating pressure is 3000 psi. Precharge pressure is 1000 psi. What is the total usable fluid
volume when the minimum BOP operating pressure is 1,200 psi?
9) On a 3000 psi accumulator system, what are the normal operating pressures seen on the
following gauges on the drillers remote control panel?
Page 9 of 69
(i) Air pressure, (ii) Accumulator pressure, (iii) Manifold pressure, (iv) Annular pressure
10) On which two gauges on the remote panel would you expect to see reduction in pressure
when the annular preventer is being closed?
11) If the air pressure on the drillers panel reads 0 psi, which of the following statements is
true?
a) No stack function can be operated from the remote panel.

b) All stack function can be operated from the remote panel.
c) Choke and kill lines can still be operated from the remote panel.
d) The annular preventer can still be operated from the remote panel.
12) Which of the problems below would not stop the BOP from closing?
a) Master control valve was not held down.

b) Four-way valve did not shift position.
c) Closing line in the BOP was blocked.
d) Leak in the hydraulic line to the BOP or in the BOP closing chamber.
e) Air pressure to the panel was lost.
f) A bulb has blown on the remote panel.
13) When drilling, which may be the correct position of the 4-way valves on the BOP
accumulator unit?
a) open
b) close
c) neutral
d) open or closed depending on BOP stack function
14) What is the normal precharge for the accumulator bottles on a 3000 psi accumulator unit?
a) 1000 psi
b) 3000 psi
c) 1200 psi
d) 200 psi
15) Name three indications that a function operated normally.
Page 10 of 69
16§) A driller needs to close in a flowing well with drill pipe in a subsea BOP stack. He pushes
the “Annular Close” button and the pilot light changes, but all gauges and the flow- meter
remain static. What is his best option?
a) Change pod and try again.

b) Call and wait for the subsea engineer.
c) Send assistant driller to manually operate the 4-ways valve on the Hydraulic Control
Manifold to close the annular.
d) Close the lower annular preventer.
17§) While drilling, an alarm goes off indicating low accumulator pressure and the flow meter
indicates a rapid loss of fluid. The best course of action is:
a) Stop drilling and shut the well in.

b) Stop drilling and call subsea engineer.
c) Stop drilling and put all function in block one at a time until the flow stops.
d) None of the above.
18§) When a function is operated, which of the following is true?
a) SPM valve will operate in both pods.

b) SPM valve will operate only on the active pod.
c) The SPM valve will operate after the function is complete.
19§) How much time is allowed for ram type preventers to close in API RP53?
20§) Name two items on the stack that are supplied by fluid from the manifold regulator.
21§) From which position in the hydraulic circuit is readback pressure taken?
a) Upstream of the regulator in the pod?

b) The regulator itself?
c) Down stream of the regulator in the pod?
22§) What is the principal reason for fitting ram locking devices such as wedgelocks or
poslocks to a subsea stack?
a) To give additional force when closing in, thus reducing delay times.
b) To lock the ram in the closed position and maintain the shear rams locked during
disconnect.
c) To lock the BOP stack to the well head and lock the lower Marine Riser Package to the
BOP stack.
Page 11 of 69
23§) The subsea hydraulic BOP control system is divided into a Control System and a Pilot
system. Which two statements are true with respect to the Pilot System?
a) The fluid in the Pilot System flows continuously while a function on the BOP takes place.
b) The Pilot System dumps fluid to the sea at every operation of BOP functions.
c) The Pilot System controls the position of all shuttle valves on the BOP stack directly.
d) The Pilot system is a closed dead-end system.
e) Pilot fluid consists of potable water, water soluble concentrate and glycol.
24§) Which two statements are true with respect to shuttle valves on a subsea stack?
a) The shuttle valves automatically seal any hydraulic leaks in the selected pod.
b) The shuttle valves prevent communication between the selected system and the redundant
system.
c) The shuttle valves are pilot operated.
d) The shuttle valves allow the retrieval of a malfunctioning pod without losing hydraulic
BOP control.
25§) What is the purpose of the "Memory Function" on electric control panels?
a) Memory Function indicates a malfunction by giving permanent light on the alarm panel
after an alarm has been acknowledged and the audible alarm has stopped.
b) Memory Function reminds the driller to add anti-freeze fluid when the temperature drops
below a set level.
c) Memory Function indicates the previous position before “Block position” of three position
functions.
d) Memory Function reminds the driller to engage Wedge Locks before hanging off.
26§) Mark the following statements true or false regarding to the use of “manipulator” type 4-
ways valve used in subsea hydraulic BOP control systems.
a) If the valve is shifted to the center or “block” position, pressure will be vented from the line
previously pressurized.
b) The center or “block” position can be used for troubleshooting hydraulic leaks.
c) The “pod selector” valve on a subsea hydraulic BOP control system is of the manipulator
type.
d) If the valve is shifted to the center or “block” position, pressure will be trapped in the line
previously pressurized.
e) Manipulator type valves are the types typically installed inside the pod hose reels.
A4 Auxiliary Equipment
1) Mark the statements below "true" or "false" when drilling with a float valve in the string.
a) Surge pressure.is reduced.

b) Reverse circulation is possible.
c) Flowback through the drillstring often occurs after pumping a slug.
d) Shut-in drillpipe pressure can be taken without starting the pumps.
2) What is the primary function of the choke in the overall BOP system?
Page 12 of 69
a) To divert contaminant to burning pit.

b) To hold back pressure while circulating up kick.
c) To divert fluid to the mud tank.
d) To prevent the loss of mud due to expansion of gas.
e) To close the well in softly.
3§) What is the reason for installing a riser fill-up valve in the marine riser of a subsea
operation?
a) To relieve the diverter system on the rig when diverting a shallow gas kick.
b) To prevent collapse of the marine riser in an emergency.
c) To increase buoyancy on the marine riser in order to relieve the riser tensioning system on
the rig.
d) To save time filling the hole when tripping out.
A5 BOP Testing
1) Identify the situations in which a BOP pressure test is required per API RP-53
a) After circulating out a gas kick.

b) Prior to drilling into a known high pressure zone.
c) After changing out BOP components or after maintenance.
d) After setting a casing string.
2) Which tool would you use if you wanted to test the BOP stack, the casing head and upper
casing seals.
a) Plug type tester

b) Cup type tester
3) While testing the BOP stack, it is noticed that hydraulic oil is leaking from the weep hole on
the upper rams. Which one of the following best describes the proper action to be taken?
a) Energize plastic seal and repair BOP at next scheduled maintenance.

b) A primary seal is leaking, secure the well and repair the seal.
c) The rams packer is leaking due to wear. Change the worn packer.
d) Do nothing. The seal requires a slight leak for lubrication purpose.
4) Why should the side outlet below a test plug be kept in the open position while testing a
surface BOP stack?
a) Because of potential damage to casing/open hole.

b) Because the test will create extreme hook load.
c) Otherwise reverse circulation will be needed to release the plug
Page 13 of 69
Section B
Pre-recorded information.
B1 Slow Circulating Rates
1) Calculate the new pump pressure at the new pump speed for each of these situations:
Pump speed Pressure New speed New pressure

A 40 200 80
B 20 400 55
C 30 600 40
D 80 2,500 60
E 70 1,800 65
2) Calculate the new pump pressure for different mud weights:
Mud weight Pressure New Mud weight New pressure

(ppg)
A 16 2,500 17.5
B 10 1,700 14
C 10 2,200 10.5
D 9.5 1,800 9.8
E 11.8 600 12.4
3) In which cases would you consider taking a new SCR?
a) Every shift.
b) Mud weight changes
c) Before and after a leak off test
d) After each connection when drilling with top drives.
e) Every 250’ of open hole.
f) After recharging pulsation dampeners on mud pump, discharge line.
g) When returning to drilling after kick.
§4) Why is the Choke Line Friction Loss (CLFL) recorded on rigs drilling with subsea BOPs?
How is the CLFL measured?
Page 14 of 69
B2 Leak off test and MAASP.
1) Calculate the maximum allowable annulus surface pressure (MAASP) in each case.
MAMW MW TVDcsg MAASP

A 14 10 6,000
B 15.5 9 7,500
2) Calculate the hydrostatic pressure for each well.
MW or Gm MD TVD Ph
A 9.5 ppg 9,000 8,000
B 15.5 ppg 21,000 18,000
C 0.889 psi/ft 11,000 9,500
3) Change these pressures to an equivalent mud weight (ppg).
Ph TVD EMW
A 3,500 7,000
B 2,800 4,000
C 5,250 9,750
4) Change the following Pressure Gradients to Mud Weights.
a) 0.56 psi/ft
b) 0.81 psi/ft
5) Change the following Mud weights to Pressure Gradients:
a) 10.4 ppg
b) 14 ppg
6) Change the following Circulating Densities to Bottom Hole Circulating Pressure:
E.D.C Depth T.V.D B.H.C.P.

A 12.5 ppg 8000 ft
B 10.2 ppg. 11400 ft
C 9.4 ppg. 12500 ft
Page 15 of 69
7) Using the following data from Leak off test results. Calculate Maximum Allowable Mud
Weights:
L.O.T. Pressure Mud Wt. Shoe Depth. T.V.D. Max Mud Wt.
A 1800 psi. 11.4 ppg. 9000 ft
B 1560 psi. 10.6 ppg. 7400 ft
C 1420 psi. 9.8 ppg. 6350 ft
8) Calculate new M.A.A.S.P. from the following Data:
Max Allow Mud Mud Wt. In Shoe Depth T.V.D. M.A.A.S.P.

Wt use.
A 19 ppg. 12 ppg. 8000 ft
B 16.7 ppg 11.5 ppg 6800 ft
C 15 ppg. 9.2 ppg. 5500 ft
9) Which three of the following conditions in the well increase the risk of exceeding the
MAASP during the well kill operation?
a) Long open hole section.

b) Large difference between formation breakdown pressure and mud hydrostatic pressure.
c) Small influx.
d) Short open hole section.
e) Large influx.
f) Small difference between formation breakdown pressure and mud hydrostatic pressure.
Questions 10-13 are base on the following information

13 3/8” surface casing is set and cemented at 3126 ft. (TVD) The cement is drilled out
together with 15 ft. of new hole, using a 10.2 ppg. mud. A Leak Off Pressure of 670 psi is
determined.
10) What is the formation fracture gradient?
a) 0.619 psi/ft
b) 0.837 psi/ft
c) 0.745 psi/ft
d) 0.530 psi/ft.
Page 16 of 69
11) What is the Maximum Allowable Annular Surface Pressure for 11.4 ppg mud used at 6500
ft TVD.
a) 865 psi
b) 474 psi
c) 449 psi
d) 563 psi
12) How often should the MAASP be recalculated?
a) After every bit change

b) After a change in mud weight
c) After every 500 ft. drilled
13) A gas kick is being circulated out. At the time the gas reaches the casing shoe (3126 ft
TVD) the pressure at the top of the bubble is 2200 psi. If the original mud weight is 11.6 ppg,
what is the casing pressure at surface.
a) 314 psi
b) 442 psi
c) 542 psi
d) 506 psi
14) The Fracture Gradient of an open hole formation at 3680 ft. is 0.618 psi/ft. The drilling
mud currently in use is 9.8 ppg. Approximately how much Surface Casing Pressure can be
applied to the well before this formation breaks down?
a) 350 psi
b) 2275 psi
c) 630 psi
d) 400 psi
Page 17 of 69
Section C
Causes of kicks.
C1 Normal and abnormal formation pressure.
1) What is primary well control?
a) The slow Circulating Rate Pressure used in the kill process.

b) The used of Mud hydrostatic to balance fluid pressures in the formation.
c) The use of Blow Out Preventers to close in a well that is flowing.
d) The use of Pit Volume and Flow Rate measuring devices to recognize the kick.
2) What is meant by Abnormal High Pressure with regard to fluid pressure in the formation?
a) The excess pressure due to circulating mud at high rates.

b) The excess pressure that needs to be applied to cause ‘leak-off ‘ into a normally pressure
formation.
c) High density mud used to create a large overbalance.
d) Formation fluid pressure that exceeds normal water hydrostatic pressure.
3) Which factors most influence the rate at which shut in pressures stabilize after the well is
shut in?
a) Gas migration
b) Friction losses
c) Permeability
d) Type of influx
C3 Gas Cutting
1) When we are drilling through a gas zone, with the proper mud density, the mud hydrostatic
pressure should be able to prevent the gas from coming into the well. However, if we still get a
kick, which of the following reasons is the best explanation?
a) When a small volume of gas is circulated from the bottom of the hole,its pressure decreases
and volume increases. This may cause a sufficient reduction in hydrostatic to cause the well
to flow.
b) The mud weight decreases due to the large splintered crescent-shaped cuttings that we get
from a high pressured zone
c) The formation pressure increases suddenly as we drill into this zone since the gas inside is
under high pressure
d) The mud is leaking into the formation thereby reducing the effective hydrostatic head,
causing an under balance
C4 Lost Circulation
Page 18 of 69
1) While running pipe back into the hole, it is noticed that the normal displacement of mud into
the trip tank is less than calculated. After reaching bottom and commencing circulation, the
return flow meter is observed to reduce from 50% to 42%. A pit loss of 2 bbl. is noted. What
is the most likely cause of these indications?
a) Partial lost circulation has occurred.

b) Total lost circulation has occurred.
c) A kick has been taken.
d) The well has been swabbed.
2) If total losses occurred while drilling with water based mud what would you do?
a) Continue drilling blind.

b) Stop drilling and fill the annulus up with water, from the top untill stabilized.
c) Stop drilling, shut the well in and see what happens.
3) Lost circulation during a well control operation is usually detected by:
a) Monitoring the return flow with the flowshow.

b) Monitoring the mud volume in the mud tanks.
c) Monitoring the weight indicator.
4) A kick has been taken and it is known that a potential lost circulation zone exists in the open
hole. Select two correct actions which can be taken to minimize pressure in the annulus during
the kill operation.
a) Maintain extra back pressure on the choke for safety.

b) Use the wait and weight method.
c) Choose a lower circulating rate.
d) Choose a higher circulating rate.
C5 Kicks as a Result of Surface Practices
1) Which of the following causes of well kicks is totally avoidable and is due to a lack of
alertness by the driller?
a) Lost circulation.
b) Gas cut mud.
c) Not keeping hole full.
d) Abnormal Pressures.
2) Which two of the following cause swabbing?
Page 19 of 69
a) Pulling the pipe too fast.

b) Insufficient trip margin.
c) Improper circulating density.
d) Going into the hole too fast.
e) Failure to slug pipe prior to pulling out of hole.
Page 20 of 69
Section D
Indications of A Kick
D1 Kicks While Drilling
1) Which of the following is the First Reliable indication that you have taken a kick?
a) Increase in torque.
b) Gas cut mud.
c) Decrease in pump pressure.
d) Increase in flow rate.
2) Why is a 20 barrel kick in a small annulus more significant than a 20 barrel kick in a large
annulus?
a) The kill weight mud cannot be calculated as easily.

b) It result in higher annulus pressures, due to the height of the kick.
c) The kicks are usually kick.
d) The pipe usually get stuck.
3) Which one of the following is not an indication when a kick may be occurring?
a) Flow rate increase.

b) Increase torque.
c) Pit gain.
d) Gas cut mud.
4) What should the driller do at a drilling break?
a) Circulate bottoms up.

b) Flow check
c) Reduce weight on bit.
d) Increase pump speed.
6) Which two practices are used to maintain primary well control as a precaution when
connection gas is noticed?
a) Pumping a low viscosity pill around bit to assist in reduction of balled bit or stabilizers.
b) Control drilling rate so that only one slug of connection gas is in the hole at any one time.
c) Pulling out of the hole to change the bit.
d) Raising Mud yield point.
e) Minimizing the time during a connection when the pumps are off.
Page 21 of 69
7) Of all the following warning signs, which two signs would leave little room for doubt that
the well is kicking?
a) flow line temperature increase.

b) increased rotary torque
c) flow rate increase.
d) decrease drill string weight
e) pit volume gain
f) increased rate of penetration
8) Which of the following statements best describes formation porosity.
a) The ratio of the open spaces to the total volume of rock.

b) The ability of fluid and gas to move within the rock.
c) The presence of sufficient salt water volume to provide gas lift.
d) All of the above
9) While drilling The active tank contained 200 bbls and the mud return line to the pits contains
20 bbls. After having a kick the tank contains 240 bbls. What is the size of the influx?.
a) 260 bbls
b) 20 bbls
c) 40 bbls
d) 240 bbls.
10) If the cutting load in the annulus was high and the well had been shut in on kick. (Answer
“Yes” or “No” to each question.)
a) Would the drill pipe pressure be higher than in a clean well? {Include a brief explanation of
your answer.}
b) Would the casing pressure be higher than in a clean well?
c) Would the casing pressure be lower than in a clean well?
11§) Two early warning signs of kicks are an increase in flow rate and pit volume. For drilling
on the floating rig these signs are difficult to detect due to the drilling vessel motion which will
cause the fluctuation of the pit level. What is the equipment that we are using to compensate
and minimize these problems and explain roughly how it works?
Page 22 of 69
12) Which of the following is a problem when using oil base mud?
a) The oil base mud will contaminate the influx.

b) In certain circumstances gas can dissolve in OBM.
c) The gas will migrate in oil base mud faster than water base mud.
d) It is difficult to detect the kick due to the gas dispersing in the oil base mud.
D2 Kick While Tripping
1) The driller is tripping pipe out of a 12 ¼” diameter hole. 25x92 ft. stand of 5” pipe have
already been pulled. There are 85 more stands to pull. The calculated metal displacement of the
9 ½” collars is 0.08 bbls/ft. The capacity of the drill pipe is 0.01776 bbls/ft and the metal
displacement 0.0075 bbls/ft. The trip tank volume has reduced from 27 barrels to 15 barrels.
What action should be taken in this situation?
a) Flow check, if negative continue to pull out of hole.

b) Shut the well in and circulate hole clean.
c) Flow check, if negative displace a 100 ft. heavy slug into annulus and continue to pull out
of hole.
d) Flow check, if negative run back to bottom and monitor returns.
e) Pull remaining stands out of hole.
2) Prior to pulling out of the hole from 10485 ft. TVD, the pipe is full of 10.4 ppg. mud. The
pipe capacity is 0.01776 bbls/ft. A 25 bbls slug weighting 12.0 ppg is pumped into the drill
pipe causing the level to drop some 216 ft. inside the drill pipe.
What is the drop in bottom hole pressure due to pumping the slug into position?
a) 25 psi
b) 0 psi.
c) 117 psi
d) 135 psi.
3) Which of the following possible indications suggest that mud hydrostatic pressure and
formation pressure are almost equal?
a) A drilling break.
b) Connection gas.
c) Large, splintery cuttings.
d) Trip gas.
e) All of above.
Page 23 of 69
4) While pulling out of the hole it is noticed that mud required to fill the hole is less than
calculated. What action must be taken?
a) Flow check, if negative displace a 100 ft. heavy slug into annulus and continue to pull out
of the hole.
b) Flow check, if negative run back to bottom circulate bottoms up and monitor returns.
c) Pull remaining stands out of the hole.
d) Flow check, if negative continue to pull out of the hole.
e) Shut the well in and circulate the hole clean.
5) You are pulling out of hole. Two 93 ft. stands of 8” drill collars have been stood back in the
derrick. The displacement is 0.0549 bbls/ft.
According to your Assistant driller - 5.1 bbls should be pump into the well. It only takes 5 bbls
to fill the hole. (Answer “Yes” or “No” to each question.)
a) Are the calculations correct?

b) Have you taken a 5 bbls influx?
c) All OK, keeps going?
6) While tripping out of the hole a kick was taken and a full bore kelly cock was stabbed and
closed. A non return type safety valve was made up on top of the kelly cock prior to stripping
in. (Answer “Yes” or “No” to each question.)
a) Should the kelly cock be closed?

b) If the kelly cock is left in the open position, can a wire line be run inside the drill string?
7) You are planing to trip out of the hole. From the list below, circle six items that you would
check before starting your trip.
a) Kelly-cock on drill floor

b) Slow circulation rate recorded
c) Sufficient power to drawworks.
d) Choke and kill manifold lined up for drilling
e) Make sure trip tank is half full
f) Trip sheets ready to record volumes displaced.
g) Make up kick sheet
h) Crossover sub on drill floor for kelly cock & drill collars
Page 24 of 69
Section E
Shut-in Procedure
1) From the list of practices shown below, choose the six most likely to lead to an increase in
the size of the influx.
a) Switch off the flow meter alarms.

b) Regular briefing for the derrickman on his duties regarding the monitoring of pit levels.
c) Drilling 20 ft further after a drilling brake, before flow checking.
d) Running regular pit drills for drill crew.
e) Maintaining stab in valves.
f) Testing stab in valves during BOP tests.
g) Excluding the drawworks from the SCR assignment.
h) Keeping air pressure on choke control console at 10 psi.
i) Calling toolpusher to floor prior to shutting in the well.
j) Not holding down master air valve on remote BOP control panel while functioning a
preventer.
2) What is the reason for raising the kelly to bring the first tool joint above the rotary table
when shutting in a well?
a) Allow the free flow of mud around bit during kill operation.
b) Allow access to the lower kelly cock and, if required, removal of the kelly.
c) Extend closing time to give softest possible shut in.
d) Allow annular to close around drillpipe because the annular is not designed to seal around
the kelly.
3) If flow through the drillpipe occurs while tripping, what should the first action be?
a. Pick up and stab kelly.
b. Run back into bottom.
c. Close the annular preventer.
d. Stab a full opening safety valve, close the valve.
4) Which list below (a, b, c or d) describes how the choke manifold will most likely be set up
for Hard Shut-in while drilling?
BOP Side Outlet Hydraulic Auto Choke(Remote Adj. Degasser Valves

Valve(HCR) Choke)
A open closed closed
B open open closed
C closed open open
D closed closed open
Page 25 of 69
5) While drilling along at a steady rate the derrickman asks to slow the mud pumps down so
that the shakers can handle the increase in cuttings coming back in the returns. Which one of
the following would be the safest course of action.
a) Continue at the same rate allowing the excess to bypass the shakers and get caught in sand
traps which can be dumped later.
b) Pick up off bottom and check for flow, if there is not any then circulate bottoms up to
reduce rate so shakers can handle cutting volume, flow check periodically during
circulation.
c) Slow down the mud pump until the shakers can handle the volume of cuttings in the
returns as requested by derrickman.
d) Slow down the drilling rate and the pump rate until the shakers clear up then go back to
the original parameters.
6) From BOP
Manual Choke Remote Choke

C1 V1
V9 V4 R1
V2
Pressure Gauge On
V6
Choke Control Panel
V10
V5
V12 V11 V3 V7 V8
1
To Poorboy Over To Stand

Degaser Board Pipe
To Poorboy
Cement
Degaser
Pit
Choose from the following the list of valves that would normally be left in the open position
when lining the choke manifold up for a hard shut in procedure when drilling.
a) V1,V2,V3,V4,V5,V6,V8,R1
b) V1,V2,V5,V6,V7
c) V1,V2,V9,C1,V10,V11
d) V1,V2,V4,V6,V8,R1
7) Which of the following would be the first action you would take if while circulating out a
kick the chicksans or hose connected to your drill string parted?
Page 26 of 69
a) Stop pump and close the full opening safety valve on the drill string. Close the choke.
b) Close the shear rams. (Shear ram position above pipe rams being used).
c) Drop the drill string and close blind/shear rams.
8) While circulating out the kick, No.1 mud pump fails. What is the first thing to do?
a) Immediately switch to No. 2 pump.

b) Fix pump as soon as possible
c) Secure the well, isolate mud pump restart using No. 2 pump.
d) Divert the well.
Page 27 of 69
Section F
Kick Data
F1 Pressure Observations
1) When a kick occurs, why is it important to get the well shut in as soon as possible? Please
answer the following items True or False.
a) A larger pit gain will result in a higher SIDPP resulting in a heavier kill mud weight
b) A larger pit gain will result in higher SIDPP and SICP
c) A larger pit gain will result in higher SICP but SIDPP will stay the same
2) A flowing well is closed in. Which pressure gauge reading is normally used to determine
formation pressure?
a) BOP manifold pressure gauge

b) Choke console drill pipe pressure gauge
c) Driller’s console drill pipe pressure gauge
d) Choke console casing pressure gauge
3) A flowing well is closed in. Which two pressure gauge readings might be used to determine
formation pressure?
a) BOP manifold pressure gauge

b) Choke console drill pipe pressure gauge
c) Driller’s console drill pipe pressure gauge
d) Choke console casing pressure gauge
4) A kick is being circulated out at 30 SPM. The drill pipe pressure reads 550 psi, and casing
pressure 970 psi. It is decided to slow the pumps to 20 SPM while maintaining 970 psi on the
casing gauge. How will this affect bottom hole pressure (exclude any Equivalent Circulating
Density [ECD] effect)? Pick one answer.
a) Increase
b) Decrease
c) Stay the same
d) No way of knowing
Page 28 of 69
5) While killing a well, as pump speed is increased, what should happen to casing pressure in
order to keep bottom hole pressure steady?
a) Casing pressure should be held steady during SPM change

b) Casing pressure should be allowed to rise during SPM change
c) Casing pressure should be allowed to fall during SPM change
6) The principle involved in Constant Bottom Hole Pressure methods of well control is to
maintain a bottom hole pressure that is :
a) Equal to the slow circulating rate pressure

b) At least equal to the formation pressure
c) Equal to the shut in drill pipe pressure
d) At least equal to the shut in casing pressure
7) At what point while correctly circulating out a gas kick is it likely that the pressure at the
casing shoe to be at its maximum?
a) At initial shut in
b) When kill mud reaches the bit
c) When kill mud reaches the shoe
d) When top of gas reaches the shoe
8) If Drill pipe Pressure is held constant while displacing the string with kill mud, what will
happen to Bottom Hole Pressure?
a) Increases
b) Remains the same
c) Decreases
9) How is a choke wash-out recognized?
a) Rapid rise in casing pressure with no change in drill pipe pressure

b) Increase in drill pipe pressure with no change in casing pressure
c) Continually having to open choke to maintain drill pipe and casing pressure
d) Continually having to close choke to maintain drill pipe and casing pressure
10) The choke has to be gradually closed due to a string washout. What effect does the
gradual closing of the choke have on the bottom hole pressure?
a) Decreases
b) Increases
c) Stays the same
Page 29 of 69
11) If Bottom Hole Pressure is held constant while circulating the influx out, the pressure on at
the casing shoe will not increase after the influx passes, even though surface pressure on the
annulus continues to rise.
a) True
b) False
Questions 12-21 are based upon the following information :
A well is closed in having taken a 30 bbl gas kick, while drilling 8 ½” hole at 11,000 ft. (TVD)
with 5” drill pipe and 750 ft. of 6 ½” drill collars
Annular capacities
5" DP / 8 ½" Hole, 0.0459 bbls / ft.
½" Hole, 0.0292 bbls / ft
12) The mud weight is 12.3 ppg and the Shut in Drill Pipe Pressure is 350 psi. Assuming the
gas Pressure Gradient to be 0.115 psi/ft, what will be the approximate Shut in Casing Pressure
:
a) 480 psi
b) 650 psi
c) 975 psi
d) 888 psi
13) While preparing to circulate Kill Mud, the gas bubble begins to migrate. If no action is
taken, what will happen to the pressure in the gas bubble as it rises:
a) Increase
b) Decrease
c) Remain approximately the same
14) What will happen to Bottom hole Pressure?
a) Increase
b) Decrease
Page 30 of 69
15) What will happen to Shut in Casing Pressure?
a) Increase
b) Decrease
16) What will happen to the pressure on the Casing Seat?
a) Increase
b) Decrease
17) If you decide to bleed enough mud to keep the Drill Pipe Pressure constant at 350 psi,
what would the pressure in the bubble do as the gas rises?
a) Increase
b) Decrease
18) What would happen to Bottom Hole Pressure?
a) Increase
b) Decrease
19) What would happen to the Shut in Casing Pressure?
a) Increase
b) Decrease
20) What would happen to the Pressure on the Casing Seat while the bubble is below the
Casing Shoe?
a) Increase
b) Decrease
Page 31 of 69
21) What would happen to the Pressure on the Casing Seat when the bubble is above the
Casing Shoe?
a) Increase
b) Decrease
22) A kick is being circulated from a well using the Driller’s Method; Pumping pressure having
been established as 1000 psi at 30 SPM. During the operation, pressure suddenly increases to
1350. You are reasonably sure that a Nozzle of the Bit is plugged. What should you do?
a) Reduce pump pressure to 1000 psi by adjusting the choke

b) Shut the well in and re-establish the pumping pressure
c) Hold casing pressure constant at the value recorded just before the bit plugged
d) (a) and (b) are acceptable courses of action
23) During the well kill operation, slowly but regularly you have had to reduce choke size
because the drill pipe and casing pressures keep dropping with constant pump strokes. What is
the likely cause of this?
a) A bit nozzle is washing out

b) The choke is washing out
c) You have a washed out pump swab
24) An influx is being circulated out using the Driller’s Method and using 1100 psi at 30 SPM.
The operator increases pump speed to 35 SPM, while holding pump pressure constant. What
happens to Bottom Hole Pressure?
a) Increases
b) Decreases
c) Remains approximately the same
25) Which of the following parameters can be affected by a drill string washout during a well
kill operation?
a) Bottom hole pressure

b) Kick tolerance
c) Formation fracture pressure
d) Slow circulating rate pressure
Page 32 of 69
26) You are killing a well using the Drillers Method, maintaining constant Drill pipe pressure.
The drill pipe pressure begins to drift down, but the casing pressure remains unchanged. The
pump strokes remain constant. You close up your choke slightly, the drill pipe pressure
remains unchanged but the casing pressure goes up. What is the probable cause for this?
a) Choke is plugging off

b) Bit is plugging off
c) Hole in drill pipe
d) Choke is washing out
27) If regularly and rather slowly, you have to pinch in the choke to maintain drill pipe and
choke pressures while the pump strokes remain constant, you may have:
a) a washed out bit nozzle

b) a washed out choke
c) a pump failure
28) Problems that occur during a killing operation may affect the parameters you are
monitoring at the surface. These are: Drill pipe pressure, casing pressure, bottom hole
pressure. For each of the following problems state the immediate effect on each of the above
parameters
For an increase draw + For a decrease draw - For no change draw =
Problem Drill Pipe Pressure Casing Pressure Bottom Hole Pressure
Choke Washout
Hole in String
Nozzle blown out
Choke Plugging
Nozzle Plugging
29) How can a washout at the adjustable choke be recognized?
a) Drill pipe and casing pressures both falling

b) Drill pipe and casing pressures both rising
c) Rapid rise in casing pressure with no change to drill pipe pressure
d) Increase in drill pipe pressure with no change to casing pressure
Page 33 of 69
F2 Shut in Pressure Interpretation
1) The reason shut in casing pressure is usually higher than the shut in drill pipe pressure is:
a) The cuttings in the annulus are lighter, therefore creating a lighter hydrostatic in the
annulus.
b) The influx fluid is usually less dense than the existing mud weight.
c) The casing pressure is not necessarily higher, it depends on whether it is an offshore or land
operation.
d) The only difference is in the type of gauges used.
900
800
700
600
500
400
300
200
100
0
TIME
2) In the diagram above, a well has been shut in and it is decided that the drilling engineer will
plot the build up of drill pipe pressure against time as shown in the drawing above. What
SIDPP would you use?
3) After shutting in on a kick, the SIDPP and SICP are observed to be stable for fifteen
minutes. Both, then, start rising slowly by the same amount. Which one of the following is the
probable cause?
a) A further influx is occurring

b) The influx is migrating up the well bore
c) The gauges are faulty
d) The BOP stack is leaking
4) After a round trip at 9854 ft with 10.3 ppg mud, we kick the pump in and start to circulate.
The well kicks and is closed in with 0 psi on the SIDPP and 150 psi on the SICP. There is no
float in the drill string. What kill mud weight is required?
a) 10.3 ppg
b) 11.3 ppg
c) 10.7 ppg
d) No way of knowing
Page 34 of 69
5) Shut in casing pressure is used to calculate
a) Kill weight mud

b) Influx gradient and type when influx volume and well geometry are known
c) Maximum Allowable Annular Surface Pressure
d) Initial circulating pressure
F3 Kick Handling Methods
1) What should the driller do at a drilling break?
a) Circulate bottoms up
b) Flow check
c) Reduce weight on bit
d) Increase pump speed
2) A kicking well has been shut in. The drill pipe pressure is ‘0’ because there is a non-return
valve (float) in the string. To establish the SIDPP, what action should be taken?
a) Shearing the pipe and reading the SIDPP directly off the casing gauge
b) Pump at kill rate into the drill string with the well shut in. When casing pressure starts to
rise, read the pump pressure. This is the SIDPP.
c) Pump very slowly into the drill pipe with the well shut in. When the pumping pressure
stabilizes, the float has opened. This pumping pressure is the SIDPP.
d) Bring the pump up to the kill rate holding the casing pressure constant by opening the
choke. The pressure shown when the pump is at kill rate is the SIDPP.
3) After circulating out a kick using the driller’s method (no weight up), are the SICP and
SIDPP about the same?
4) A gas kick is being circulated up the well. What is the surface pit volume most likely to do?
a) Increase
b) Stay the same
c) Decrease
Page 35 of 69
5) On a surface stack, what would happen if when bringing the pumps up to kill speed, the
casing pressure was allowed to fall below shut in casing pressure?
a) Formation would most probably break down

b) More influx would be let into the well bore
c) It would have no effect on anything
6) For each of the following statements, note whether it relates to the Drillers Method or the
Wait and Weight Method.
a) Minimize pressures generated in the annulus due to gas expansion.

b) Remove influx from well before pumping kill mud
c) Pump kill mud while circulating influx up the annulus
d) Maintain Drill Pipe pressure constant for 1st circulation
7) Which one of the following actions taken while stripping into the hole will help to maintain
an acceptable bottom hole pressure?
a) Pumping a volume of mud into the well, equal to the drill pipe closed end displacement at
regular intervals
b) Bleeding off the drill pipe steel displacement at regular intervals
c) Pumping a volume of mud into the well, equal to the drill pipe steel displacement, at
regular intervals
d) Bleeding off the drill pipe closed end displacement at regular intervals
8) Which of the following statements is true?
a) There is no difference between using the Drillers method and the Wait and Weight method
b) If the kill mud is being circulated up the annulus before the kick has reached the shoe then
Wait and Weight method will reduce the risk of breaking down the formation compared to
using the Drillers method
c) The Wait and Weight method should always be used because the pressure against the open
hole will always be lower when using the Drillers method
9) Mud weight increase required to kill a kick should be based upon :
a) shut in drill pipe pressure

b) shut in casing pressure
c) original mud weight plus slow circulation rate pressure losses
d) shut in casing pressure minus shut in drill pipe pressure
10) How is the Initial Circulating Pressure found on a land rig or a jack-up, when the slow
pump rate circulating pressure is not known but a kick has been taken?
Page 36 of 69
a) Circulate at desired strokes per minute to circulate out the kick, but hold 200 psi back
pressure on drill pipe side with choke
b) Add 400 psi to casing pressure and bring pump up to kill rate while using the choke to
keep the casing pressure +400 constant
c) Bring pump strokes up to kill rate while keeping casing pressure constant by manipulating
the choke, observed pump pressure is ICP
d) Add 1000 psi to shut in drill pipe pressure and circulate out the kick
11) Having completed the first circulation of the Driller’s Method, the well is shut in. Should
casing pressure be:
a) Less than Shut in Drill Pipe Pressure

b) Equal to Shut in Drill Pipe Pressure
c) Greater than Shut in Drill Pipe Pressure
12) On the second circulation of the Driller’s method, if the casing pressure was held constant
until the kill mud reached Surface, what would happen to the bottom hole pressure?
a) Increase
b) Decrease
c) Stay the same
13) Using Wait and Weight method, if the drill pipe pressure drops below the line of the graph
as the kill mud goes down, what happens to the bottom hole pressure?
a) Increases
b) Decreases
c) Stays the same
14) You have taken a kick with a non-return valve (float) in the drill string. After shutting the
well in properly, it is best to :
a) Use the annulus pressure to calculate the kill weight mud

b) Start raising the mud weight 1 ppg per circulation until the well is dead
c) Use either the rig pump or cementing unit pump to increase pressure in 100 psi increments
until a change is seen on casing gauge
d) Pump slowly into the drill pipe. When the pump pressure stabilizes, the float is open. The
pumping pressure is the SIDPP used to calculate kill mud
Page 37 of 69
15) A well is being killed using the Driller’s Method.

Original shut-in drill pipe pressure = 500 psi
Original shut-in casing pressure = 900 psi
After the first circulation, the well is shut in and pressures allowed to stabilize. They then read
:
Shut-in drill pipe pressure = 500 psi
Shut-in casing pressure = 650 psi
It is decided not to spend any more time cleaning the hole
Which one of the following actions should be taken
a) Prepare to use the Wait and Weight method

b) Bull-head the annulus until shut-in casing pressure is reduced to 500 psi
c) Reverse circulate until shut-in casing pressure is reduced to 500 psi
d) Continue with second circulation of Drillers Method (holding casing pressure constant until
mud reaches the bit)
16) If the slow pump circulating pressure was not known, and a kick has been taken with the
well closed in, how would you find the ICP?
a) Bring pump up to the desired rate, while holding the casing pressure 150 psi above the
original SICP
b) Bring pump up to desired rate, but hold 200 psi back pressure on the drill pipe
c) Bring pump up to the desired rate holding casing pressure constant by manipulating the
hydraulic choke
d) Circulate at desired kill rate but hold casing pressure 100 psi below MAASP
17) The correct gauge to use for calculating the kill weight mud is :
a) the gauge on the choke and kill manifold

b) the drill pipe pressure gauge on the drillers console
c) the casing gauge on the drillers console
d) the drill pipe gauge on the remote auto choke panel
e) the casing gauge on the remote auto choke panel
18) The following diagrams show the approximate changes in pressure at certain points in the
well during the first circulation of the Driller’s Method. Match the following locations to their
respective diagrams:
a) Surface casing pressure

b) Casing shoe pressure
c) Bottom hole pressure
d) Pump pressure
Page 38 of 69
(i)
PSI
TIME
(ii)
PSI
TIME
(iii)
PSI
TIME
(iv)
PSI
TIME
(c) DYNAMIC
PRESSURE
1500
1250
D
RI (d)
LL 1000
PI
PE
PR 750
ES (e)
SU (a) STATIC
500 PRESSURE
RE
(P
SI) 250
(b)
(x)
KILL MUD PUMPED
Drill pipe pressure graph of the one circulation method
Page 39 of 69
19) From the figure above, match the following steps with correct explanation
a) 1) Drillstring displaced with kill mud

b) 2) ICP = SIDPP + kill rate pressure
c) 3) 0 psi (static)
d) 4) SIDPP (static)
e) 5) Drillstring volume pumped
x) 6) FCP= Kill rate pressure x kill mud
weight / original mud weight
(c)
1500
1250 DYNAMIC
PRESSUR
E
1000
D
RI
LL (d)
PI 750
PE
PR
ES (a)
SU 500
(e)
RE
(P STATIC
SI) PRESSUR
250 E
(b)
(x) (y) (z)
Drill pipe pressure graph of the driller method
20) From the figure above, match the following steps with correct explanation
a) 1) 0 psi (static)
b) 2) FCP = kill rate pressure x kill mud
c) weight / original mud weight
d) 3) Annular volume pumped
e) 4) Drillstring volume displaced
x) 5) ICP = SIDPP + kill rate pressure
y) 6) SIDPP (static)
z) 7) Annular volume pumped
8) Drillstring volume pumped
Page 40 of 69
F4 Calculations
Exercise 1
Calculate the following
1)
Old Mud Wt. New Mud Wt. Old Pressure New Pressure
PPG PPG psi. psi.
9.68 10.0 1850
11.5 12.2 2500
11.0 12.6 300
2)
Old Strokes New Strokes Old Pressure New Pressure

SPM SPM psi psi
75 40 2450
30 60 400
20 80 180
3)
Mud Wt E.C.D. T.V.D. Mud Hydrostatic B.H.C.P. A.P.L.

PPG PPG Ft. psi psi psi
10.0 10000 300
11.2 5824 76
12.0 9800 6000
14.54 15.1 16000
11450 6200 320
9.84 10.6 8700
4) Calculate the hydrostatic pressure for each well :
a) 9.5 PPG at 9,000 feet M.D. and 8,000 feet T.V.D.

b) 15.5 PPG at 18,000 feet T.V.D. and 21,000 feet M.D.
c) 0.889 PSI/FT at 11,000 feet M.D. and 9,500 feet T.V.D.
5) Change these pressures to an equivalent mud weight in ppg.
a) 3,500 psi at 7,000 feet.

b) 4,000 feet with 2,800 psi.
c) 12,000 feet M.D. / 10,500 T.V.D. with 9,000 psi.
6) Calculate equivalent mud weights for these wells :
Page 41 of 69
a) BHP = 9,800 psi, Depth = 9,800 feet

b) BHP = 4,580 psi, Depth = 10,000 ft TVD, 11,500 feet M.D.
7) Calculate kill mud weight for the following wells
a) SIDPP = 600 PSI, Depth = 10,000 ft, Mud wt. = 10 PPG, SICP = 900 PSI
b) Mud wt = 9.5 PPG, SICP = 2,000 PSI, SIDPP = 1,200 PSI, Depth = 9,500 PSI
c) SICP = 600 PSI, Depth = 15,000 feet T.V.D., 17,000 M.D. SIDPP = 300 PSI, Mud
Weight = 17 PPG
8) Calculate the new pump pressure at the new pump speed for each of these situations
Old strokes Old Pressure New Strokes New Pressure

a) 30 spm 600 psi 40 spm psi
b) 80 spm 2500 psi 60 spm psi
c) 70 spm 1800 psi 20 spm psi
d) 40 spm 200 psi 80 spm psi
e) 20 spm 400 psi 55 spm psi
9) Calculate the new pump pressure for different mud weights :
a) 16 ppg mud at 40 spm = 2,500 psi. What is the pressure with 17.5 ppg mud at 40 spm?
b) Present pump pressure = 1,700 psi at 50 spm with 10 ppg. What is the new pump pressure
at 50 spm with 14 ppg?
10) Calculate the maximum allowable annulus surface pressure (MAASP) for these wells:
a) Maximum allowable mud weight = 14 ppg, Mud weight = 10 ppg, Depth of casing = 7,500
feet TVD
b) Maximum allowable mud weight = 15.5 ppg, Mud weight = 9.0 ppg, Depth of casing =
7,500 feet TVD
11) Calculate the influx height for each situation :
a) 25 bbl gain, 900 feet of 6 ½" drill collars in an 8 ½" hole (Annular capacity =
0.0292 bbl/ft)
b) 40 bbl gain, 500 feet of 6 ½" drill collars in an 8 ½" hole (0.0292 bbl/ft annular
capacity), 5" drill pipe precedes (.0459 bbl/ft annular capacity)
Page 42 of 69
12) Calculate the bottom hole circulating pressure of each well:
APL hydrostatic pressure Mud wt BHCP

a) 400 psi 6500 psi 10 ft
b) 250 psi 5000 psi 10.5 psi
13) Calculate the equivalent circulating density of each well :
APL hydrostatic pressure Depth TVD ECD

a) 350 psi 5050 psi 9800 ft
b) 40 psi 6800 psi 12000 psi
14) Calculate the annular pressure loss for each well:
BHCP Mud wt Depth TVD APL

a) 6000 psi 11.6 psi 9450 ft
b) 2600 psi 9.8 psi 5000 psi
15) Calculate the new pump pressure with the following new mud weights :
Old Mud wt Old pressure New Mud Wt New pressure
10 ppg 220 psi 10.5 ppg

9.5 ppg 1800 psi 9.8 ppg
11.8 ppg 600 psi 12.4 ppg
16) Change the following pressure gradients to mud weights :
Gradient Mud weight

a) .56 psi/ft
b) .81 psi/ft
17) Change the following mud weights to pressure gradients :
Mud weight Pressure Gradient

a) 10.4 ppg
b) ppg
Page 43 of 69
18) Change the following circulating densities to bottom hole circulating pressures :
ECD Depth TVD BHCP

a) 12.5 ppg 8000 ft
b) 10.2 ppg 11400 ft
c) 9.4 ppg 12500 ft
19) Using the following data from the Leak Off test results, calculate maximum allowable mud
weights :
LOT pressure Mud weight Shoe depth TVD Max mud weight
a) 1800 psi 11.4 ppg 9000 ft
b) 1560 psi 10.6 ppg 7400 ft
c) 1420 psi 9.8 ppg 6350 ft
20) Using the same well data, calculate the height of each influx :
Drill Collar Length = 700 ft

DC - OH Capacity = 0292 bbl/ft
DP - OH Capacity = .0459 bbl/ft
Influx volume = Height ft.
10 bbls = ft
20 bbls = ft
30 bbls = ft
21) Using the following well data, calculate Influx gradients :
SICP SIDPP MUD weight Ht of Influx Gradient

a) 800 psi 720 psi 11.5 ppg 400 ft
b) 950 psi 600 psi 10.6 ppg 840 ft
c) 680 psi 550 psi 10.2 ppg 350 ft
22) Calculate new MAASP from the following data :
Max. allowance Mud weight Shoe depth MAASP

mud weight in use TVD
a) 19 ppg 12 ppg 8000 ft
b) 16.7 ppg 11.5 ppg 6800 ft
c) 15 ppg 9.2 ppg 5500 ft
Page 44 of 69
23) Using the following data, calculate kill mud weights :
SICP SIDPP Mud weight Depth Depth Kill Mud

TVD MD
a) 600 psi 450 psi 10 ppg 9500 ft 10000 ft
b) 850 psi 690 psi 11 ppg 12000 ft 12300 ft
c) 780 psi 570 psi 10.5 ppg 11200 ft 11800 ft
d) 700 psi 300 psi 14 ppg 13000 ft 13400 ft
24) A well is shut in with 500 psi on the casing pressure. The annulus contains 8,000 ft of 10.0
ppg mud above 1,000 ft of 9.0 ppg saltwater. What is the equivalent mud weight at 8,000 ft?
At 9,000 ft?
a) 8,000 ft ; 11.2 ppg

b) 8,000 ft ; 11.7 ppg
c) 9,000 ft ; 11.0 ppg
d) 9,000 ft ; 11.9 ppg
25) Prior to pulling out of the hole from 10,485 ft. TVD, the pipe is full of 10.4 ppg mud. The
pipe capacity is .01776 bbls/ft. A 25 bbls slug weighing 12.0 ppg is pumped into the drill pipe
causing the level to drop some 216 ft. inside the drill pipe.
What is the drop in bottom hole pressure due to pumping the slug into position?
a) 25 psi
b) 0 psi
c) 117 psi
d) 135 psi
26)
Drill pipe capacity = 0.0178 bbls/ft
Drill pipe metal displacement = 0.0082 bbls/ft
Average stand length = 93 ft
Calculate :
a) Mud required to fill the hole per stand when pulled ‘dry’ (bbls per stand)
b) Mud required to fill the hole per stand when pulled ‘wet’ (bbls per stand)
27) You are determining your kill rate pressure and bringing your pump rate up to a pre-
determined 30 SPM by holding the shut in casing pressure constant. You have got a kick in the
well of 220 psi shut in drill pipe pressure. At 30 SPM your drill pipe circulating pressure is
1060 psi. Calculate the slow circulating rate pressure loss.
a) 700 psi
b) 770 psi
c) 800 psi
d) 840 psi
Page 45 of 69
28) Calculate the equivalent circulating density in the following circumstances:
Circulating pressure = 3100 psi
Pressure losses
Surface equipment = 20 psi
Drill string = 930 psi
Nozzles = 1800 psi
Annulus = 350 psi
Drilled depth 12,300 ft. (11,500 ft. TVD)

Mud weight 11.4 ppg
ECD is
a) 10.8 ppg
b) 12.0 ppg
c) 11.4 ppg
d) 12.3 ppg
29) A well is drilled to 13,000ft with 13.2 ppg mud. The formation pressure at that depth is
8,700 psi. The intermediate casing is 43.5 lb/ft, 9 5/8 in. pipe set to 11,000 ft. The drill pipe is
4 ½ in.(ID 3.826”) and the collars displacement is 0.04bbl/ft. The operator requires hole filling
after 5 stands of drill pipe or collars are pulled. Will the well kick when pulling the drill pipe
dry? Drill collars dry? (Assume no swabbing effects with an average length of 90ft per stand)
a) Pulling pipe ; no kick

Pulling collars ; kick
b) Pulling pipe ; kick
Pulling collars ; no kick
c) Kicks for both drill pipes and drill collars
d) Does not kick for either drill pipe or drill collar
Page 46 of 69
F4 Calculations
Exercise 2
Questions 1-4 are based on the following information
13 3/8” surface casing is set and cemented at 4250 ft. (TVD). The cement is drilled out
together with 15 ft. of new hole, using a 11 ppg mud. A leak off test pressure of 800 psi is
determined. (Hole TVD 7000ft)
1) What is the formation fracture gradient?
a) 0.188 psi / ft
b) 0.686 psi / ft
c) 0.760 psi / ft
d) 0.384 psi / ft
2) What is the maximum allowable annular surface pressure for 12.3 ppg mud in use at 7350 ft.
TVD :
a) 373 psi
a) 511 psi
b) 884 psi
c) 1982 psi
3) How often should the MAASP be recalculated?
a) After every bit change

b) After a change in mud weight
c) After every 500 ft. drilled
4) A gas kick is being circulated out. At the time the gas reaches the casing shoe (4250 ft.
TVD), the pressure at the top of the bubble is 3000 psi. If the original mud weight is 12 ppg,
what is the casing pressure at the surface? (Hole TVD 7000ft)
a) 348 psi
b) 442 psi
c) 1368 psi
d) 2625 psi
Page 47 of 69
Questions 5-9 are based upon the following information
A deviated borehole has a measured depth of 12,320 ft. (TVD 10429 ft). 9 5/8”, 47 lb/ft.
casing in set at a measured depth of 9750 ft. (9200 ft. TVD). 11.4 ppg mud is in use when the
well kicks and is closed in.
Shut in Drill Pipe Pressure is 750 psi

Shut in Casing Pressure is 1050 psi and kick volume is 15 bbls.
Pre- recorded information is as follows :
Fracture mud weight = 14.4 ppg

Capacity of 19.5 lbs. Drill pipe = 0.01776 bbl/ft.
Capacity of 9 5/8” J55 casing = 0.0732 bbl/ft.
Slow Circulating Rate Pressure = 850 psi
5) The maximum allowable annular surface pressure is rounded off to :
a) 1370 psi
b) 1480 psi
c) 1435 psi
d) 1415 psi
6) The kill mud weight required to balance the formation pressure is:
a) 13.1 ppg
b) 12.6 ppg
c) 12.8 ppg
d) 12.2 ppg
7) The kill mud weight with a Safety Margin of 100 psi is:
a) 13.4 ppg
b) 13.0 ppg
c) 12.4 ppg
d) 11.8 ppg
8) The initial circulating pressure is:
a) 1400 psi
b) 1600 psi
c) 1900 psi
Page 48 of 69
9) The final circulating pressure (using kill mud weight with a 100 psi Safety Margin is) :
a) 850 psi
b) 970 psi
c) 920 psi
d) 1050 psi
10) The Fracture Gradient of an open hole formation at 3680 ft. is 0.618 psi/ft. The drilling
mud currently in use is 9.8 ppg. Approximately how much Surface Casing Pressure can be
applied to the well before this formation breaks down?
a) 350 psi
b) 2275 psi
c) 630 psi
d) 400 psi
11) In the area where local legislation requires that BOP equipment must be rated so that
maximum anticipated formation pressures do not exceed 75% of BOP equipment pressure
ratings, what is the Minimum Acceptable rating for equipment to be used in drilling Normally
Pressured Formation to 16,000 ft. TVD?
a) 2,000 psi BOP Equipment

b) 3,000 psi BOP Equipment
c) 5,000 psi BOP Equipment
d) 10,000 psi BOP Equipment
e) 15,000 psi BOP Equipment
Drilling 12 ¼" hole at 7653 ft. TVD with 11.7 ppg mud, the well kicks and is closed in. The
shut in DPP is 430 psi. SICP is 600 psi. Pit gain 28 bbl.
Pre-Recorded Information
13 3/8" Casing Shoe at 3975 ft. TVD

A Leak Off Test on the formation at shoe, using 11.2 ppg mud, showed a surface pressure of
910 psi when Leak Off occurred
Drill Collars 8 ¼" OD x 2 ½" ID 546 ft. long. Capacity 0.0061 bbls / ft
Drill Pipe 5" OD x 19.5 lbs / ft. Capacity 0.01776 bbls / ft
Open Hole - Drill Collar Annulus Capacity is 0.0796 bbls / ft
Open Hole - Drill Pipe Annulus Capacity is 0.1215 bbls / ft
13 3/8" Casing - drill Pipe Annulus capacity is 0.1239
Slow Pump Rate 30 SPM - Output 5 gal / stk at 730 psi
* For Subsea Candidates use

* Subsea Information
Water Depth - 700 ft

Air Gap - 75 ft
Page 49 of 69
1. Choke Line Capacity 0.0087 bbls / ft

2. Riser Capacity 0.3892 bbls / ft
3. Drill Pipe Displacement 0.0076 bbls / ft
4. CLFL ( Choke Line Friction) 75 psi
Complete an IWCF kick sheet as required to assist in answering questions 12-21
12) What is the Fracture Gradient at the 3 3/8" casing shoe?
a) 0.792 psi / ft
b) 0.811 psi / ft
c) 0.834 psi / ft
d) 0.861 psi / ft
13) What is the MAASP with 11.7 ppg mud in the hole?
a) 910 psi
b) 730 psi
c) 1004 psi
d) 806 psi
14) The Kill Mud required is:
a) 11.7 ppg
c) 12.8 ppg
d) 13.3 ppg
b) 13.9 ppg
15) The Surface to Bit strokes are :
a) 987
b) 1016
c) 1088
d) 1164
16)
The Bit to Shoe strokes are § Subsea:

Strokes to displace riser to Kill Mud
a) 3562 3370
b) 3257 2370
c) 3752 2300
d) 3604 2730
Page 50 of 69
17)
The Bit to Surface Strokes are : § Subsea :

shoe to BOP Strokes
a) 7100 4744
b) 7300 3388
c) 7500 3332
d) 7700 3563
18) The Initial Circulating Pressure is :
a) 1060 psi
b) 1160 psi
c) 1260 psi
d) 1330 psi
19) The Final Circulating Pressure is :
a) 800 psi
b) 730 psi
c) 1330 psi
d) 1270 psi
20) The gradient of influx is:
a) 0.087 psi / ft
b) 0.212 psi / ft
c) 0.1225 psi / ft
d) 0.327 psi /ft
21) The estimated time required to kill the well at 30 SPM is:
a) 3 hours approximately
b) 5 hours approximately
c) 7 hours approximately
d) 11 hours approximately
22) You are tripping out of the hole :
Hole Depth 12,000 ft

Mud Weight 10 ppg
Drill Pipe capacity 0.01776 bbls / ft
Slug 12 ppg density
Displaced 20 bbls
Page 51 of 69
The fluid level in the drill pipe has dropped 223 ft. How much bottom hole pressure has been
lost?
a) 702 psi
b) 116 psi
c) 70 psi
d) 0 psi
23) Given the following data, complete an IWCF kick sheet as far as required to complete
questions 23(a) to 23(i)
Drill String Data Capacities

5" Drill Pipe 0.01776 bbls /ft
8 ¼ Drill Collars - 630 ft 0.0077 bbls / ft
5" Heavy weight DP 450 ft 0.0087 bbls / ft
Hole Data
Casing depth 4000 ft. 13 3/8" casing
Hole Depth 7591 ft. 12 ¼"
Mud weight 9.5 ppg
Annular Capacities
8 ¼” DC 12 ¼” hole 0.0796 bbls / ft
5" DP 12 ¼" hole 0.1215 bbls / ft
5" DP 13 3/8" casing 0.1238 bbls / ft
LOT 1070 psi test mud 9 ppg
Pump Data
6" liners 97% efficiency = .102 bbls / stk
§ Subsea Information :
Water Depth 300 ft
Air Gap 90 ft
Choke Line Capacity 0.0087 bbls / ft
Riser Capacity 0.3892 bbls / ft
Drill Pipe Steel Displacement 0.0076 bbls / ft
Questions :
a) What is the maximum mud weight?

b) Total Drill string Capacity
c§) Total Annulus Capacity
d) Bit to shoe volume
e§) Total system volume
f) Surface to bit strokes
g) Bit to shoe strokes
h§) Bit to surface strokes
Page 52 of 69
i§) Total circulation strokes
24) You have taken a kick and shut the well in. The active tank while drilling contained 250
bbls. And the mud return line to the pits contains 25 bbls.
The tank now contains 300 bbls. How many barrels of mud has been displaced from the
well?
a) 0 bbls
b) 25 bbls
c) 50 bbls
d) 275 bbls
25) You are pulling out of hole. Two x 93 ft stands of 8" drill collars have been stood back in
the derrick. The displacement is 0.0538 bbls. / ft. According to your Assistant Driller, 10 bbls
should be pumped into the well. It only takes 10 bbls to fill the hole. (Answer yes or no to
each question)
a) Are the calculations correct?

b) Have you taken a 5 bbls influx?
c) All Ok, keep going
26) Use an IWCF kill sheet to assist you in answering questions 26(a) through 26(i)
Well Data
Hole size 8 ½ in
Hole depth 11937 ft. TVD / MD
Casing 9 5/8 in. casing set at 9474 ft.
Drill pipe 5 in. capacity = 0.0178 bbls / ft
Heavy weight pipe 5 in., 497 ft. long
Capacity = 0.0088 bbls / ft
Drill Collars 6 ¼ in., 892 ft. long
Capacity = 0.006 bbls / ft
Mud density 14.3 ppg
Volume open hole / collars 0.0322 bbls / ft
Volume open hole / drill pipe / HWDP 0.0459 bbls / ft
Volume casing / drill pipe 0.0493 bls / ft
Fracture mud wt. At the casing shoe 16.9 ppg
Mud pumps Output = 0.117 bbls / stk
Slow circulating rate 820 psi at 30 spm / (Riser)
1180@30 spm ( Choke Line)
The well has been shut in after a kick:
Kick Data :
Shut-in Drill Pipe Pressure 580 psi

Shut-in Casing Pressure 755 psi
Pit Gain 12 bbls
Page 53 of 69
The well will be killed using the Driller’s Method at 30 spm
§* For Subsea use
Water Depth...................................................................... 2120 ft

Air Gap ............................................................................. 80 ft
Steel Displacement ............................................................ 0.0076 bbls / ft
Riser Capacity 19.75" ID ................................................... 0.3789 bbls / ft
Choke Line Capacity 2 7/8" ID .......................................... 0.008 bbls / ft
26a) Strokes to pump down inside drillstring from surface to bit
26b i). Strokes to pump from bit to shoe

§ ii). Strokes to displace riser (subsea)
§ 26c) Strokes to pump from bit to surface
26d) Kill mud weight (no safety factor)
26e i). Initial Circulating Pressure

§ ii). Initial Dynamic Casing Pressure
26f) Final Circulating Pressure
26g) MAASP with current mud weight
26h) MAASP after circulation of kill mud
26i i). Time for complete circulation

§ ii). Subsea excluding riser volume
Inlet
15.0'
6.5'
Shakers
27) From the diagram, calculate the pressure (psi) required to unload the MGS
(M.W. = 12.5 ppg.)
Page 54 of 69
IWCF deviated well control exercise #1 (surface BOP stacks)
Prepare a deviated well control kick sheet (use attaches kick sheets) from the following well
data and answer the accompanies questions :
Well Data :
Hole Size 8 ½"
Hole Depth 14370 ft., MD (5250 ft., TVD)
Kick-off Point 1640 ft., MD (1640 ft., TVD)
End of Build 4265 ft., MD (3494 ft., TVD)
Casing Shoe 9 5/8" x 47 lbs/ft @ 10600 ft., MD (4593 ft., TVD)
Capacities :
Drill Pipe 5” OD x 19.5 # 0.01776 bbls/ft
Heviwate 480 ft 5” OD x 3” ID 0.00874 bbls/ft
Drill Collar 660 ft 6 ½” OD x 2 13/16” ID 0.0077 bbls/ft
Drill Collar/Open Hole 0.0291 bbls/ft

Drill Pipe / HWDP / Open Hole 0.0458 bbls/ft
Drill Pipe / HWDP / Casing 0.0489 bbls/ft
Pump Data :
Displacement 0.12 bbls/stroke
Active Surface Volume 470 bbls
Slow Circulating Rate 870 psi @ 30 spm
Formation Strength Data 1027 psi LOT using 10.5 ppg mud weight
Kick Data :
Mud Weight 10.85 ppg
Kick depth 14370 ft., MD (5250 ft., TVD)
Pit Gain 19 bbls
SIDPP 725 psi
SICP 785 psi
Page 55 of 69
Questions ( Surface BOP stack)
1. What is the pressure safety margin at the casing shoe with the well shut in?
2. How many strokes to pump from surface to bit?
3. What is the initial circulating pressure?
4. What is the final circulating pressure?
5. How many strokes to pump from surface to kick-off point depth?
6. What is the circulating pressure at the kick off point?
7. How many strokes to pump from surface to the end of build depth?
8. What is the circulating pressure at the end of build depth?
9. Calculate the pressure drop per 100 strokes of kill fluid pumped inside the string from the
end of build depth to the bit.
10. Calculate the MAASP (Maximum Allowable Annular Surface Pressure) after circulation of
Kill Mud.
11. If we neglected the directional nature of the well and decided to use a conventional Vertical
Well Kill Sheet to remove the influx, calculate the pressure over balance at the end of build
depth.
12. What will be the consequences of this overbalance in the well bore?
Page 56 of 69
IWCF deviated well control exercise ( Subsea BOP stack)
Prepare a deviated well control kick sheet (use attached kick sheets) from the following well
data and answer the accompanied questions
Well Data :
Hole Size 8 ½"
Hole Depth 14370 ft., MD (5250 ft., TVD)
Kick-off Point 1640 ft., MD (1640 ft., TVD)
End of Build 4265 ft., MD (3494 ft., TVD)
Casing Shoe 9 5/8" x 47 lbs/ft @ 10600 ft., MD (4593 ft., TVD)
Capacities :
Drill Pipe 5” OD (NC50, S-135) 0.01776 bbls/ft
Drill Pipe 5” Closed end displacement 0.0254 bbls/ft
Heviwate 480 ft 5” OD x 3” ID 0.00874 bbls/ft
Drill Collar 660 ft 6 ½” OD x 2 13/16” ID 0.0077 bbls/ft
Choke Line 520 ft x 3” ID 0.0085 bbls/ft
Marine Riser 505 ft 0.3892 bbl/ft
Drill Collar/Open Hole 0.0291 bbls/ft

Drill Pipe / HWDP / Open Hole 0.0458 bbls/ft
Drill Pipe / HWDP / Casing 0.0489 bbls/ft
Pump Data :
Displacement 0.12 bbls/stroke
Active Surface Volume 470 bbls
Slow Circulating Rate Riser Circuit 870 psi @ 30 spm
Slow Circulating Rate Choke Circuit 960 psi @30 spm
Formation Strength Data 1027 psi LOT using 10.5 ppg mud weight
Kick Data :
Mud Weight 10.85 ppg
Kick depth 14370 ft., MD (5250 ft., TVD)
Pit Gain 19 bbls
SIDPP 725 psi
SICP 785 psi
Page 57 of 69
Questions ( Subsea BOP Stacks)
1. What is the pressure safety margin at the casing shoe with the well shut in?
2. How many strokes to pump from surface to bit?
3. What is the initial circulating pressure?
4. What is the final circulating pressure?
5. How many strokes to pump from surface to kick-off point depth?
6. What is the circulating pressure at the kick off point?
7. How many strokes to pump from surface to the end of build depth?
8. What is the circulating pressure at the end of build depth?
9. Calculate the pressure drop per 100 strokes of kill fluid pumped inside the string from the
end of build depth to the bit.
10. Calculate the MAASP (Maximum Allowable Annular Surface Pressure) after circulation of
Kill Mud.
11. If we neglected the directional nature of the well and decided to use a conventional
Vertical Well Kill Sheet to remove the influx, calculate the pressure over balance at the end
of build depth.
12. How many strokes to pump to displace Marine Riser to kill fluid before opening the BOP?
Page 58 of 69
Answers.
Section A
A1 Blowout Preventers and Diverters.
1 no, no, yes, yes

2 b
3 d
4 A = 2, B = 2, C = 1, D = 1, E = 2, F = 2
5 Yes, yes, no, no
6 Yes, no, yes, yes
7 No, no, yes
8 c
9 d
10 c
11 c
12 d
13 2, 4, 1, 3
14 3000, 16 ¾, 300; 15000, 3 1/16, 250; 20000, 2 9/16, 350; 2000, 13 5/8,
250
15 b
16 a, b c, f
17 a
18 b
19 D
20 A
A2 BOP control systems.
1 214
2 T, T, T, F
3 d
4 a
5 a, c
6 b, c
7 (i) a
7 (ii) b
7 (iii) d
7 (iv) c
8 40
9 120, 3000, 1500, 750-1500 psi
10 2, 4
11 a
12 1
13 d
14 a
Page 59 of 69
15 a. light changes color, b. read back pressure drops, c. read back

pressure recovers, d. flow meter stops at a proper reading.
16 a
17 c
18 a
19 The BOP control system should be capable of closing each ram BOP in
45 seconds or less. API RP53 3rd edition March 1997 (13.3.5, p.31)
20 pipe rams, connectors, failsafe valves, shear rams
21 (b) The connection is to the regulator, the measurement is taken on the
downstream (regulated) side.
22 b
23 d&e
24 b, d
25 c
26 a=T, b=T, c=T, d=F, e=F
A4 Auxiliary Equipment.
1 a=F, b=F, c=T, d=F

2 b
3 b
A5 BOP testing.
1 b, c, d
2 b
3 b
4 a
Section B
B1 Slow Circulating Rates.
1 a. 800 psi, b. 3025 psi, c. 1067 psi, d. 1407 psi, e. 147 psi
2 a. 2734 psi, b. 2380 psi, c. 2310 psi, d. 1857 psi, e. 631 psi
3 a, b, g
4 For deep water drilling we have significant pressure drop on the choke
line due to its length. This will affect the calculation of the initial
circulating pressure in a wll control situation.
Three methods for measuring CLFL
1) 1.1 Pump at SCR, taking return up the riser, read (SCRP)
1.2 Close BOP, open choke line failsafe valves
1.3 Circulate at SCR, Taking return through a wide open
choke.Record Drill Pipe pressure.
1.4 The difference between the two is CLFL
2) 2.1 Pump down the choke line at SCR, taking returns up the riser
2.2 The pumping pressure record at SCR is CLFL.
3) 3.1 Pump down the kill line and up the choke
Page 60 of 69
3.2 The pump pressure is twice the CLFL
B2 Leak Off Test & MAASP
1 a. 1248 psi, b. 2535 psi

2 a. 3952 psi, b. 14508 psi, c. 8446 psi
3 a. 9.62 ppg., b. 13.46 ppg. C. 16.48 ppg.
4 a. 10.77 ppg., b. 15.58 ppg.
5 a. 0.5408 psi/ft, b. 0.728 psi/ft
6 a. 5200 psi, b. 6046 psi, c. 6110 psi.
7 a. 15.25 ppg., b. 14.65 ppg, c. 14.1 ppg
8 a. 2919psi, b. 1838.7 psi, c. 1658.8 psi.
9 a, e, f
10 c
11 b
12 b
13 a
14 d
Section C
C1 Normal and Abnormal Formation Pressure
1 b
2 d
3 c
C3 Gas Cutting
1 a
C4 Lost Circulation
1 a
2 b
3 b
4 b-c
C5 Kicks As Result of Surface Practices
1 c
2 a, b
Section D
D1 Kick While Drilling
1 d
Page 61 of 69
2 b
3 b
4 b
5 b, e
6 c, e
7 a
8 b
9 a. = No, b. No, c. = Yes
10 PVT (A pit volume totalizing system). It will report overall pit gain or loss
by using multiple pit monitors and resolving individual losses and gains
reported by each monitor into a single value.
11 b
D2 Kick While Tripping
1 d
2 b
3 e
4 b
5 a. = No (10.2), b. =Yes, c.= No.
6 a.= No, b. = No
7 a, b, c, e, f, h
Section E
E1 Shut-In Procedure
1 a, c, g, h, i, j
2 b
3 d
4 d
5 b
6 a
7 a
8 a
Section F
F1 Pressure Observation
1 F, F, T
2 b
3 b, d
4 c
5 a
6 b
7 d
8 a
Page 62 of 69
9 d
10 b
11 a
12 d
13 c
14 a
15 a
16 a
17 b
18 c
19 a
20 a
21 c
22 b
23 b
24 b
25 a, d
26 c
27 b
28 ---
-==
-==
+++
+==
29 a
30 c, e
F3 Shut In Pressure Interpretation
1 b
2 700-710
3 b
4 a
5 b
F3 Kick Handling Methods
1 b
2 b
3 Yes
4 a
5 b
6 a. W&W
b. Driller
c. W&W
d. Driller
7 d
8 b
Page 63 of 69
9 a
10 c
11 b
12 a
13 b
14 d
15 a
16 c
17 d
18 d., b., a., c.
19 a. 4)
b. 3)
c. 2)
d. 6)
e. 1)
x. 5)
20 a. 6)
b. 1)
c. 5)
d. 2)
e. 4)
x. 3)
y. 8)
z. 7)
F4: Calculation Exercise 1
1)
Old Mud Wt. New Mud Wt. Old Pressure New Pressure
ppg. ppg. ppg. ppg.
9.68 10 1850 1912
11.5 12.2 2500 2652
11 12.6 300 344
2)
Old Strokes New Strokes Old Pressure New Pressure

spm. spm. psi psi
75 40 2450 697
30 60 400 1600
20 80 180 2880
3)
Mud Wt E.C.D. T.V.D. Hydrostatic B.H.C.P. A.P.L.

ppg. ppg. ft psi. psi. psi.
10 10.58 10000 5200 5500 300
11.2 11.35 10000 5824 5900 76
Page 64 of 69
11.77 12 9800 6000 6115 115

14.54 15.1 16000 12097 12563 466
10.41 10.95 11450 6200 6520 320
9.84 10.6 8700 4452 4795 343
4 a. 3952 psi., b. 14508 psi., c 8446 psi.

5 a. 9.62 ppg., b. 13.46 ppg., c. 16.48 ppg.
6 a. 19.23 ppg., b. 8.81 ppg.
7 a. 11.16 ppg., b. 11.93 ppg., c. 17.39 ppg.
8 a. 1067 psi., b. 1407 psi., c. 147 psi., d. 800 psi.,e. 3025 psi
9 a. 2735 psi., b. 2308 psi
10 a. 1560 psi., 2535 psi.
11 a. 856.16 ft., b. 1053.38 ft.
12 a. 6900 psi., b. 5250 psi.
13 a. 10.6 ppg., b. 10.96 ppg.
14 a. 300 psi., b. 52 psi.
15 a. 231 psi., b. 1857 psi., c. 631 psi
16 a. 10.77 ppg., b. 15.58 ppg.
17 a. 0.5408 psi/ft., b. 0.728 psi/ft.
18 a. 5200 psi., b. 6047 psi., c. 6110 psi.
19 a. 15.24 ppg., b. 14.65 ppg., c. 14.10 ppg.
20 a. 342.47 ft., b. 684.94 ft., c. 908.28 ft.
21 a. 0.398 psi/ft., b. 0.1345 psi/ft., c. 0.159 psi/ft.
22 a. 2912 psi., b. 1838 psi., c.1658 psi.
23 a. 10.92 ppg., b. 12.11 ppg., c. 11.48 ppg., d. 14.45 ppg.
24 a., c.
25 b.
26 a. 0.72-0.80, b. 2.3-2.5
27 d
28 b
29 a
F4 Calculation Exercise
1 c
2 b
3 b
4 a
5 c
6 c
7 b
8 b
9 b
10 d
11 d
12 b
13 d
Page 65 of 69
14 b
15 c
16 a ; // subsea // b
17 d ; // subsea // c
18 b
19 a
20 c
21 b ; //subsea// b
22 d
23 a) 14.14 ppg, b) 124.4 bbls, c) 907.7 bbls , //subsea// 862.74, d) 412.5
bbls ,e) 1033 stks, //subsea// 988 stks ,f) 1221 stks g) 4040 stks, h) 8899
stks, //subsea// 8460 stks, i) 10119 stks //subsea// 9680 stks
24 b
25 a) Yes, b) No, c) Yes
26 a) 1688, b) (i)862 +/- 5 stks, (ii) subsea 6647 stks, c) 4854 +/- 5 stks, *
subsea 4088 stks, d) 15.23 = 15.3 ppg, e) (i) 1400 psi, (ii) subsea 395 psi,
f) 873, g) 1281, h) 822, i) (i)218(ii) subsea 192.6 mins
27 4.225 psi
F4 Surface BOP Stacks
1 158 psi
2 2036 strokes
3 1595 psi
4 1084 psi
5 243 strokes
6 1393 psi
7 632 strokes
8 1175 psi
9 6.53 psi / 100 strokes
10 308 psi
11 261 psi
12 Breakdown at the shoe
F4 Subsea BOP Stacks

1 158 psi
2 2036 strokes
3 1595 psi
4 1084 psi
5 243 strokes
6 1393 psi
7 632 strokes
8 1175 psi
9 6.53 psi / 100 strokes
10 308 psi
11 261 psi
12 1532 strokes
Page 66 of 69
Formulae for Well Control.
1 Hydrostatic pressure: Ph (psi) Ph = MW × TVD × (0.052)
2 Pressure gradient: Gm (psi/ft) Gm = MW × (0.052)
3 To convert pressure gradient to mud Gm

weight. MW =
(0.052)
4 To convert pressure to mud weight. Ph

EMW =
(0.052) × (TVD)
5 Hydrostatic pressure using pressure Ph = Gm × TVD

gradient.
6 Equivalent Circulating Density: ECD APL

(ppg) ECD = MW +
(0.052) × (TVD)
7 Maximum Allowable Mud Weight Plot

from leak off test: MAMW (ppg) MAMW = MWlot +
(TVDshoe ) × (0.052)
8 Maximum Allowable Annular Surface MAASP = ( MAMW − MW ) × (TVDshoe ) × (0.052)

Pressure: MAASP (psi)
9 Boyle’s gas law. P1 × V 1 = P 2 × V 2
10 Pressure change for change in stroke 2

 SPMnew 
rate. Pnew = Pold × 
 SPMold 
11 Pressure change for a change of mud  MWnew 

Pnew = Pold × 
 MWold 
weight
12 Kill weight mud: MWkill (ppg) SIDPP

MWkill = MW +
(TVD) × (0.052)
13 Shut In Casing Pressure (psi) SICP = (Gm − Gi ) × Hi + SIDPP
14 Initial Circulating Pressure: ICP (ppg) ICP = Pscr + SIDPP
15 Final Circulating Pressure: FCP (ppg) MWkill

FCP = Pscr ×
Pscr = PL MW
16 Barite required to increase mud 1500(W 2 − W 1))

weight: Barite (lbs/bbl) Barite =
(35.8 − W 2)
Page 67 of 69
17 Height of influx: Hi (ft) Gain Pit

Hi =
Capacity Annular
18 Trip Margin/Safety Factor (ppg) Safety Margin

TM = + MW
TVD × 0.052
19 Estimated influx gradient (psi/ft).  SICP − SIDPP 

G Influx = MW × (0.052) −  
 Hi 
20 Triplex pump output at 100% Output = (0.000243) × ( D) 2 × Stroke

efficiency (bbl/stroke). (Liner
diameter D and stroke in inches)
21 Percolation Rate (ft/hr) ∆P( psi / hr )

PR =
MW × 0.052
22 Pipe capacity (BBL/ft). ( ID) 2

Capacity Pipe =
1029.4
23 Annular capacity (bbl/ft). ( Dh) 2 − ( Dp) 2

Capacity Annular =
1029.4
24 Annular velocity (ft/min) 1029.4 × Output Pump Output Pump

Velocity Annular = =
Outputpump= bbl/min ( Dh ) 2 − ( D p ) 2 Capacity Annular
25 Formation Pressure (Pf) Pf = SIDPP + ( MW × (0.052) × TVD)
26 Gas migration rate: Rm (ft/hr ∆SICP Increase in pressure (psi / hr)

Rm = =
Gm Gm
27 Height of slug. Volume slug Height Drypipe × MW

H slug = =
Capacity Pipe ( MWslug − MW )
28 Height of dry pipe. H Slug × ( MWslug − MW )

H Drypipe =
MW
29 Slug weight. H Drypipe × MW

MWslug = + MW
H Slug
30 Bottomhole pressure (BHP): Static BHP = SIDPP + Ph (Mud in drillstring)

case in drillstring.
31 Bottomhole pressure: Static case in BHP = SICP + Ph (Mud and influx in annulus)
annulus.
Page 68 of 69
32 Bottomhole pressure: Dynamic case. BHP = Ph ( drillstring ) + APL
33 Cross sectional area (square inches). A = Diameter 2 × 0.7854
34 Rectangular tank capacity. L × W × D (FT)

Capacity ( BBL) =
5.61
35 Change in BHP when pulling dry pipe MW × 0.052 × LPipe × DisplacementMetal

out of hole. ∆BHP =
(Capacity Csg − DisplacementMetal )
36 Change in BHP when pulling wet MW × 0.052 × L Pipe × ( Displacement + Capacity Pipe )
pipe out of hole. ∆BHP =
( Capacity Csg − Displacement − Capacity Pipe )
Page 69 of 69

Preschool Exercises PDF

Uploaded by

Copyright:

Available Formats

Preschool Exercises PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Preschool Exercises PDF

Uploaded by

Copyright:

Available Formats

Sedco Forex

Jakarta Learning Centre

Pre-school exercises for Well Control

Well Control Equipment ........................................................................................................................ 4

Indications of a kick ............................................................................................................................. 21

Formulae for Well Control................................................................................................................... 67

Pre-School exercises for Well Control

Well Control Equipment

A1 Blowout Preventers and Diverters.

a) To show that ram body rubber is leaking.

a) 6-5/8” reg. Box X 7-5/8” reg. Pin

4) Two types of valves may be used in the drill string:

Type 1 Non return, stab in safety valve or inside BOP

Indicate in the table which statement describes the valves.

a) The upper pipe rams are closed?

a) With drill pipe in hole, can we repair the side outlets?

8) The kill line should enter a stack so that

a) The well can be circulated if the blind rams are in use.

a) Reciprocating motion of the pipe increases the wear on seals.

10) What do the term “6BX” stamped on a flange represent?

a) Ratio between closing & opening volume.

Flange#1___________psi __________ inches __________ deg.F

18) What is the main function of a diverter?

a) To shut in a shallow kick.

a) 2000 psi BOP equipment

a) The marine riser may collapse.

A2 BOP control systems

Component Volume to Open Volume to close

a) 2 times usable accumulator volume.

Accumulator Manifold Annular Problem

a) No stack function can be operated from the remote panel.

a) Master control valve was not held down.

15) Name three indications that a function operated normally.

a) Change pod and try again.

a) Stop drilling and shut the well in.

18§) When a function is operated, which of the following is true?

a) SPM valve will operate in both pods.

a) Upstream of the regulator in the pod?

a) Surge pressure.is reduced.

a) To divert contaminant to burning pit.

a) After circulating out a gas kick.

a) Plug type tester

a) Energize plastic seal and repair BOP at next scheduled maintenance.

a) Because of potential damage to casing/open hole.

B1 Slow Circulating Rates

Pump speed Pressure New speed New pressure

2) Calculate the new pump pressure for different mud weights:

Mud weight Pressure New Mud weight New pressure

3) In which cases would you consider taking a new SCR?

B2 Leak off test and MAASP.

MAMW MW TVDcsg MAASP

2) Calculate the hydrostatic pressure for each well.

3) Change these pressures to an equivalent mud weight (ppg).

4) Change the following Pressure Gradients to Mud Weights.

5) Change the following Mud weights to Pressure Gradients:

6) Change the following Circulating Densities to Bottom Hole Circulating Pressure:

E.D.C Depth T.V.D B.H.C.P.

8) Calculate new M.A.A.S.P. from the following Data:

Max Allow Mud Mud Wt. In Shoe Depth T.V.D. M.A.A.S.P.

Flange#1_psi inches __ deg.F