Code No: R201213 R20 SET - 1

I B. Tech II Semester Regular/Supplementary Examinations, August- 2022

NETWORK ANALYSIS
(Com. To ECE, EIE, ECT)
Time: 3 hours Max. Marks: 70
Answer any five Questions one Question from Each Unit
All Questions Carry Equal Marks
UNIT- I
1 a) Obtain the equivalent resistance at the terminals a-b for the circuit shown? (7M)

b) Define Graph, Tree, Basic tie set matrix and cut set matrix for a planar network (7M)
with an example?
Or
2 a) Use mesh analysis to find the current io in the circuit shown below. (7M)

b) Determine the RMS value of the current waveform shown below? If this current (7M)
waveform is passed through 2 Ω resistor, find the average power absorbed by the
resistor?

UNIT- II
3 a) A simple RL series circuit is excited by a sinusoidal voltage source. The circuit is (7M)
initially relaxed. At t=0, the switch is closed find the response i(t) for the current.
Source voltage is Vm Sin(ωt+φ)
b) The capacitor in Fig. is initially charged to 3 V with the polarity shown.(i) Find (7M)
the mathematical expressions for the voltage vc and the current ic when the switch
is closed (ii) Sketch the waveforms for vc and ic.

1 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 SET - 1
R20

Or
4 a) Find i(t) in the circuit of Fig. for t>0. Assume that the switch has been closed for a (7M)
long time.

b) Calculate the capacitor voltage for t<0 and t>0 for the circuit shown below. (7M)

UNIT- III
5 a) A coil of inductance 318.3mH and negligible resistance is connected in series with (7M)
a 200 Ω resistor to a 240 V, 50 Hz supply. Calculate (i) the inductive reactance of
the coil (ii) the impedance of the circuit (iii) the current in the circuit (iv) the
voltage across each component and (v) the circuit phase angle.
b) When one coil of a magnetically coupled pair has a current 5.0 A the resulting (7M)
fluxes φ11 and φ12 are 0.2 mWb and 0.4 mWb, respectively. If the turns are N1=
500 and N2= 1500, find L1, L2, M, and the coefficient of coupling k.
Or
6 a) Find the power factor of the circuit seen by the source for the network shown (7M)
below.

b) Two coils are connected in series and their effective inductance is found to be 15 (7M)
mH. When the connection to one coil is reversed, the effective inductance is found
to be 10 mH. If the coefficient of coupling is 0.7, determine (i) the self-inductance
of each coil, and (ii) the mutual inductance.
2 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 SET - 1
R20

UNIT- IV
7 a) Design a series RLC circuit that will have an impedance of 10 Ω & at the resonant (7M)
frequency of ω0 = 100 rad/s and a quality factor of 80. Find the bandwidth.
b) State and explain maximum power transfer theorem with an example? (7M)

Or
8 a) Apply the superposition principle to find i and power delivered to the 3 Ω resistor (7M)
in the circuit shown below?

b) Derive the expression for resonant frequency, band width and quality factor of a (7M)
series resonant circuit?
UNIT- V
9 a) Obtain the ABCD parameters of the circuit shown below (7M)

b) Derive the relationship between hybrid and Z parameters of two port network? (7M)
Or
10 a) Determine the h parameters for the circuit shown below. (7M)

b) Derive the relationship between transmission and Z parameters of two port (7M)
network?

3 of 3

|'''|'|'|''|''||'|||
Code No: R201213 R20 SET - 2
I B. Tech II Semester Regular/Supplementary Examinations, August- 2022
NETWORK ANALYSIS
(ECE, EIE, ECT)
Time: 3 hours Max. Marks: 70
Answer any five Questions one Question from Each Unit
All Questions Carry Equal Marks
UNIT-I
1 a) Find v1 and v2 in the circuit shown below. Also calculate i1 and i2 and the power (7M)
dissipated in the 12 Ω and 40 Ω resistors.

b) Suppose your circuit laboratory has the following standard commercially available (7M)
resistors in large quantities:1.8 Ω, 20 Ω, 300 Ω, 24 kΩ, 56 kΩ. Using series and
parallel combinations and a minimum number of available resistors, how would
you obtain the following resistances for an electronic circuit design?
(i) 311.8 Ω (ii) 40 K Ω
Or
2 a) For the bridge network shown in Fig., find Rab and i. (7M)

b) Calculate the RMS value of the current wave form shown below? (7M)

UNIT-II
3 a) Determine i, i0 and vo for t > 0 in the circuit shown in Fig. Assume that the switch (7M)
was closed for a long time.

1 of 3
|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 2

erive the expression for voltage response and current response of a series RC (7M)
b) Derive
circuit with initially uncharged capacitor subjected to step input?
input
Or
4 a) Derive the expression for voltage response and current response of a series RL (7M)
circuit with no initial inductor current subjected to step input?
b) In Fig. shown the switch has been closed for a long time and is opened at t = 0. (7M)
Find i and v for all time

UNIT-III
5 a) A coil has a resistance of 44Ω and an inductance of 9.55 mH. Calculate ((i) the (7M)
reactance (ii)) the impedance, and (iii)) the current taken from a 240V, 50 Hz
supply. Also determine the phase angle between the supply voltage and current.
b) The combined inductance of two coils connected in series is 0.6H or 0.1H (7M)
depending on relative directions of currents in the two coils. If one of the coils has
self-inductance
inductance of 0.2 H, find the mutual inductance and coefficient of coupling.
Or
6 a) Find I0 in Fig. using mesh analysis?
analysis (7M)

b) Explain the principle of ‘dot’ rule used for the analysis of coupled circuits with an (7M)
example?
UNIT-IV

7 a) State and explain thevenin’s theorem with an example? (7M)

b) For the series resonant circuit of Fig. find I, VR, VL, and VC at resonance. What is (7M)
the Q of the circuit? If the resonant frequency is 5000 Hz, find the bandwidth.
What is the power dissipated in the circuit at the half-power
half power frequencies?

Or
2 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 2

8 a) State and explain Milliman’s theorem? (7M)

b) Find the maximum power that can be delivered to the resistor R in the circuit (7M)
shown below.

UNIT-V

9 Find the transmission parameters for the circuit shown below (14M)

Or
10 a) Obtain the y parameters for the network shown in Fig. (7M)

b) Derive the relationship between hybrid and ABCD parameters of two port (7M)
networks?

3 of 3

|'''|'|'|''|''||'|||
Code No: R201213 R20 SET - 3
I B. Tech II Semester Regular/Supplementary Examinations, August- 2022
NETWORK ANALYSIS
(ECE, EIE, ECT)
Time: 3 hours Max. Marks: 70
Answer any five Questions one Question from Each Unit
All Questions Carry Equal Marks
UNIT-I
1 a) Calculate the node voltages in the circuit shown in Fig. (7M)

b) Define basic cut-set and basic loop incidence matrices and write these for the (7M)
following graph by taking 1, 2, 3 as tree branches as shown in Fig.

Or
2 a) Explain the principle of duality and draw the dual of the following network? (7M)

b) Find the node voltages V1, V2, V3 in the fig. shown below? (7M)

UNIT-II
3 a) Calculate the capacitor voltage for t < 0 and t > 0 for the circuit shown. (7M)

1 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 3

b) The switch has been in position a for a long time. At t=0 it moves to position b. (7M)
Calculate i(t) for all t > 0.

Or
4 a) In the circuit shown below, find i(t) for t > 0 if i(0) = 2 A. (7M)

b) The switch in Fig. 8.4 was open for a long time but closed at t = 0. Determine: (i) (7M)
i(0+), v(0+) (ii) di(0+)dt , dv(0+)/dt (iii) i(∞), v(∞).

UNIT-III
5 a) Explain Star to delta conversion with relevant derivation? (7M)
b) Write short notes on dot convention used in magnetically coupled coils. Determine (7M)
the inductance of the three series connected inductors shown in Fig.

Or
6 a) A coil of resistance 5Ω and inductance 120mH in series with a 100 µF capacitor, (7M)
is connected to a 300V, 50 Hz supply. Calculate (i) the current flowing, (ii) the
phase difference between the supply voltage and current, (iii) the voltage across
the coil and (iv) the voltage across the capacitor.

2 of 3
|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 3

b) Obtain an expression for Co-efficient

Co of coupling. (7M)
UNIT-IV
7 a) The bandwidth of a series resonant circuit is 400 Hz. (i) If the resonant frequency (7M)
is 4000 Hz, what is the value of Q? (ii) If R = 10 Ω,, what is the value of XL at
resonance (iii) Find the inductance L and capacitance C of the circuit.
b) A series resonant circuit has a bandwidth of 100 Hz and contains a 20 mH (7M)
inductance and a 2 µF F capacitance. Determine (i) fo (ii) Q (iii) Zin at resonance
(iv) f2
Or
8 a) State and explain reciprocity theorem with an example? (7M)
b) Obtain the Norton equivalent of the circuit in Fig. shown to the left of terminals aa- (7M)
b. Use the result to find current i.

UNIT-V
9 a) Write a brief note on series and parallel connection of two port networks? (7M)
b) Find the four short-circuit
circuit admittance parameters for the resistive two-port (7M)
network shown

Or
10 a) Find the impedance parameters for the two-port shown in Fig. (7M)

b) Find the hybrid parameters for the circuit shown in Fig. (7M)

3 of 3

|'''|'|'|''|''||'|||
Code No: R201213 R20 SET - 4
I B. Tech II Semester Regular/Supplementary Examinations, August-
August 2022
NETWORK ANALYSIS
(ECE, EIE, ECT)
Time: 3 hours Max. Marks: 70
Answer any five Questions one Question from Each Unit
All Questions Carry Equal Marks
UNIT-I
1 a) Obtain the equivalent resistance Rab for the circuit shown below and use it to find (7M)
current i.

b) For the arrangement shown, find (a) the equivalent capacitance of the circuit, (b) (7M)
the voltage across QR and (c) the charge on each capacitor.

Or
2 a) For the bridge network shown, find io using mesh analysis. (7M)

b) For the graph shown, write the cut set schedule and obtain the relation between (7M)
tree branch voltages and branch voltages.

1 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 4

UNIT-II
3 a) Consider the circuit shown below. Find i(t) for t < 0 and t > 0. (7M)

b) Refer to the circuit shown in, Calculate: (7M)

(i) iL(0+), vC(0+), and vR(0+) (ii) iL(∞), vC(∞), and vR(∞).

Or
4 a) An un-charged 80 µF capacitor is connected in series with a 1 kΩ resistor and is (7M)
switched across a 110 V supply. Determine the time constant of the circuit and the
initial value of current flowing. Also determine the value of current flowing after
(a) 40 ms and (b) 80 ms
b) Refer to the circuit shown below, the switch is closed at t = 0. (i) determine (7M)
equations for iL and vL.(ii) At t = 300 ms, open the switch and determine equations
for iL and vL during the decay phase. (iii) Determine voltage and current at t = 100
ms and at t =350 ms. (iv) Sketch iL and vL

UNIT-III

5 a) A resistance of 50 Ω is connected in series with a capacitance of 20 µF. If a supply (7M)

of 200V,100 Hz is connected across the arrangement find (i) the circuit
impedance, (ii) the current flowing, and (iii) the phase angle between voltage and
current
b) Two identical coupled coils have an equivalent inductance of 80 mH when (7M)
connected series aiding and 35 mH in series opposing. Find L1, L2, M and K.
Or
6 a) A resistance of 50 Ω is connected in series with a capacitance of 20 µF. If a supply (7M)
of 200V, 100 Hz is connected across the arrangement find (i) the circuit
impedance, (ii) the current flowing, and (iii) the phase angle between voltage and
current
b) Define the following terms with an example (i) self-inductance (ii) Mutual (7M)
inductance (iii) Coefficient of coupling (iv) Reluctance
UNIT-IV
7 a) For the circuit shown in Fig. (i). Determine the resonant frequency (ii) Find the (7M)
voltage VC at resonance (iii) Determine the currents IL and IC at resonance (iv)
Find Quality factor.
2 of 3

|'''|'|'|''|''||'|||
 Code No: R201213 R20 SET - 4

b) For the network shown in Fig., find the value of R for maximum power to R, and (7M)
determine the maximum power to R for each network.

Or
8 a) Find the Thevenin equivalent circuit for the bridge network across the terminals (7M)
a&b. Also find the current through the resistor of 1 Ω connected between a &b?
&

b) State and explain tellegen’s theorem? (7M)

UNIT-V
9 a) Through derivation, express the Z parameters in terms of the ABCD parameters. (7M)
b)  5Ω 2  (7M)
If h =   find admittance parameters?
 −0.5 0.1 S 
Or
10 a) Prove that when two port networks are connected in parallel, the y parameters of (7M)
the overall network are the sum of the y parameters of the individual networks
b) For the two-port network shown in the Fig.,
Fig. the currents I1 and I2 entering at port 1 (7M)
and 2 respectively are given by the equations.
I1= 0.5 V1 - 0.2 V2
I2 = - 0.2V1 + V2
Where V1 and V2 are the port voltages at port 1 and 2 respectively. Find the Y and
Z parameters for the network.
network

3 of 3

|'''|'|'|''|''||'|||