The document provides instructions for using TRACE32 software to debug a NXP 4905 board. It describes locating the TRACE32 software files, required hardware including a LAUTERBACH emulator and target board, configuring switches on the board, starting the TRACE32 application, loading symbols, and using breakpoints and step-by-step commands to debug code.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online from Scribd
The document provides instructions for using TRACE32 software to debug a NXP 4905 board. It describes locating the TRACE32 software files, required hardware including a LAUTERBACH emulator and target board, configuring switches on the board, starting the TRACE32 application, loading symbols, and using breakpoints and step-by-step commands to debug code.
The document provides instructions for using TRACE32 software to debug a NXP 4905 board. It describes locating the TRACE32 software files, required hardware including a LAUTERBACH emulator and target board, configuring switches on the board, starting the TRACE32 application, loading symbols, and using breakpoints and step-by-step commands to debug code.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online from Scribd
The document provides instructions for using TRACE32 software to debug a NXP 4905 board. It describes locating the TRACE32 software files, required hardware including a LAUTERBACH emulator and target board, configuring switches on the board, starting the TRACE32 application, loading symbols, and using breakpoints and step-by-step commands to debug code.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online from Scribd
Download as doc, pdf, or txt
You are on page 1of 7
TRACE32
How to use FERNANDEZ Steve 8 Nov 2007
SUMMARY Location Path of TRACE32................................................................................................3 Hardware Desccription.......................................................................................................3 1- LAUTHERBACH...............................................................................................................3 2 - TRACE32 Program...........................................................................................................3 3 - Board 4905.........................................................................................................................3 Switch configuration...........................................................................................................4 Starting application.............................................................................................................4 breakpoints and step by step command .............................................................................7
How to use TRACE32 TRACE32 is a software in Graphical Interface able to drive board 49xx, The emulator part of TRACE32 is responsible for carrying out debugging functions, for managing breakpoints, for displaying memory and high-level-language structures Here is how to load and use this software: Location Path of TRACE32 The package zipped is located at: P:\_SOFTWARE\internal_software_releases\mcu_image_release\4901\nxp490x\Integration 4901\3. Tools\TRACE32-Rfrence T32.zip => Pachage to unzip at the root of c:/ Desktop Icons => shortcut used to run trace32 in different connection. Notice that those shortcuts have some parameter set in the target path, please copy them in your desktop. Hardware Desccription
3 - Platform board 4905 usable also for 4901 Switch configuration First of all, we have to configure the switches, see below the poper configuration used in 4901 board |0+
1 2 3 4 5 6 7 8
Switch 2, position | = USB component (cp2101) disable Switch 2, position + = USB component enable (virtual serial COM via USB ) Switch 6, position | = Normal Boot of firmware Switch 6, position + = Boot in download mode of firmware Switch 7, position | = Debug disable Switch 7, position + = Debug enable
Starting application After verifying that the hardware are well connected, make sure that all devices are powered on; then run the USB_C program, the below window of TRACE32 is displayed: the application is STARTED
Notice that 3 panels is loaded automatically and new buttons are available depending of .cmm files setted in T32_Config directory. Then press P2 button to switch on another workspace.
Some panels appear in P2 wokspace, then on the B::SYStem window clic on Up Mode to reset the board:
After that press on NXP F1 button to load symbol
The following windows appear => Remapped data at @ 9000 0000
Hence, back on to the P2 workspace, you can now load symbols according to the Baseline compiled; to brose the symbol you can go to View/Symbols/Browse The following windows appear, you can browse all function matching with the code compile in cygwin it is usefull to debug code using breakpoints and step by step execution.
Then when the symbols are loaded reclic on Up and play button, the board is under running step.
If the board doesnt start properly, please re do the same step until the board is started. The MMI (board screen display) should display the time, network name Check if the board can be control by TRACE32 => Press Pause button and check if nothing answers when pressing keyboard on board button pad. Now the board system is well attached with TRACE32 software.
breakpoints and step by step command Let us show how to set a breakpoint. Select in the symbols browser the name of the function you want to break; as an example hkbd1_0StartKeyFrame function have been taken, it will break whenever you press on a keyboard Pad button. Below windows show: i. B::Break.List windows => give a summury of breakpoints list setted, when the breakpoint is highlighted it means that the program is stopped at this breakpoint. Be aware that only 2 breakpoint is authorised. ii. B::Data.List windows => display the code when clicking on the breakpoint setted. Notice on the below picture that the program is stop at the breakpoint highlighted with a grey lign. To make a breakpoint simply double-click on the ASM code. To verify if TRACE32 is stop at breakpoint, check at your bottom right (red circle) if the state is at stopped at breakpoint. Then to run step by step press on F2 key.
