ल्याव टेक्निसियन स्विकृत

Download as pdf or txt
Download as pdf or txt
You are on page 1of 5

Choice)

Part I - Civil Engineering

1. Estimating and Costing

1.1 Specifications
1.1.1 Definition, Purpose, Types, Necessity
1.1.2 Specification for Road Works Embankment construction, Sub-grade, Sub-bases,
Surface dressing using hot bitumen (two coats), Premix carpet with hot bitumen, Cement
concrete pavement

2. Construction Management
2.1 Organization
2.1.1 Need for organization
2.1.2 Responsibilities of a Lab Technician
2.1.3 Relation between Client, Contractor and Consultant
2.2 Labour Management and Occupational Health and Safety
2.2.1 Organizing crew
2.2.2 Accident prevention
2.3 Planning and Control
2.3.1 Construction schedule
2.3.2 Equipment and materials schedule
2.3.3 Construction stages and operations
2.3.4 Bar chart

3. Soil Mechanics

3.1 General
3.1.1 Soil types and classification
3.1.2 Three phase system of soil
3.1.3 Unit Weight of soil mass: bulk density, saturated density, submerged
density and dry density
3.1.4 Interrelationship between specific gravity, void ratio, porosity, degree
of saturation, percentage of air, voids air content and density index
3.2 Compaction of soil
3.2.1 Factors affecting soil compaction
3.2.2 Optimum moisture content
3.2.3 Relation between dry density and moisture content
3.3 Shear Strength of Soils
3.3.1 Mohr-Coulomb failure theory
3.3.2 Cohesion and angle of internal friction
3.4 Foundation Engineering
5.6.1 Terzaghi's general bearing capacity formulas and their application
Part II- Highway Engineering

4. General
4.1 Introduction to transportation systems
4.2 Historic development of roads
4.3 Classification of road in Nepal
4.4 Basic requirements of road alignment
4.5 Province no. 2 Province civil service Act 2077
4.6 Province no. 2, Engineering releted Act, Rules and Regulations.
5. Geometric Design
5.1 Use of Nepal Road Standard, 2027(First Revision 2045) and subsequent
revision in road design
6. Highway Materials
6.1 Highway Construction Materials
6.1.1 Mineral Materials, Binding Materials and materials of general
construction purpose (stone, cement, bitumen and bricks)
6.2 Sub-grade soil
6.2.1 Suitability, Classification
6.3 Stone aggregate
6.3.1 Types, properties
6.4 Binding Materials (Bitumen)
6.4.1 Types, suitability
6.5 Steel and Gabion wires
6.5.1 Types, suitability

7. Road Pavements
7.1 Definition, types, pavement structures (sub-grade, sub-base, base and wearing
courses)
7.2 Road Machineries (Introduction, types, different compacting
equipments)
7.3 Road Construction Technology
7.3.1 Introduction, works involved in road construction earthwork, drainage
and protection work, pavement work, miscellaneous works
7.3.2 Construction material, equipment and procedure for construction of
Earthen roads
7.3.3 Construction material, equipment and procedure for construction of
Graveled roads
7.3.4 Construction material, equipment and procedure for construction of Soil
Stabilized roads
7.3.5 Construction material, equipment and procedure for construction of
WBM roads
7.3.6 Construction material, equipment and procedure for construction of
Bituminous roads, Surface Dressing (Single and Double)
7.3.7 Construction material, equipment and procedure for construction of
Grouted or penetration macadam
7.3.8 Construction material, equipment and procedure for construction of
Otta seal surfacing
Part III - Laboratory Testing

8. Earth work: Laboratory Testing procedure and equipments for


8.1 Gradation, Identification
8.2 Proctor compaction (Optimum moisture content & Maximum dry density)
8.3 Plasticity Index
8.4 Dynamic cone penetration
8.5 California Bearing Ratio (CBR)
8.6 Specific gravity

9. Sub-base/base: Laboratory Testing procedure and equipments for


9.1 Gradation, Material identification
9.2 Compaction (Maximum dry density & Optimum moisture content)
9.3 California Bearing Ratio (CBR)
9.4 Compaction-Field density test by sand replacement method/core cutter method
9.5 Los-Angeles abrasion
9.6 Aggregate impact value
9.7 Aggregate crushing value

10. Pavement
10.1 Aggregate: Laboratory Testing procedure and equipments for
10.1.1 Los-Angeles abrasion
10.1.2 Aggregate Impact value
10.1.3 Aggregate crushing value
10.1.4 Bitumen stripping value
10.1.5 Flakiness Index
10.1.6 Gradation
10.2 Bitumen: Laboratory Testing procedure and equipments for
10.2.1 Penetration
10.2.2 Flash/Fire point test
10.2.3 Specific gravity test
10.2.4 Water content test
10.2.5 Solubility test
10.2.6 Ductility test
10.2.7 Penetration of Residue after loss heating
10.2.8 Softening point test
10.2.9 Viscosity
10.2.10 Loss on heating

11. Cement Concrete: Laboratory Testing procedure and equipments for


11.1 Normal consistency of cement
11.2 Setting time of cement
11.3 Compression test of cement mortar cube
11.4 Slump test
11.5 Compression test of concrete
11.6 Gradation of sand & Aggregates
11.7 Fineness modulus of sand
11.8 Clay in sand
11.9 Concrete mix design

12. Steel reinforcement and Gabion wire: Laboratory Testing procedure and equipments
for
12.1 GI wire
12.1.1 Zinc coating test
12.1.2 Tensile strength test
12.1.3 Uniformity test
12.1.4 Adhesion test

12.2 Steel reinforcement Bars


12.2.1 Yield and ultimate tensile strength
12.2.2 Elongation

13. Laboratory and Field Test


13.1
13.2 Surface distress Index
13.3 Road Roughness Index
13.4 Sampling Techniques of construction materials for highway and bridge works
13.5 Quality Assurance Plan
13.6 Quality control for Road and Bridge works

---The End---

You might also like