Asd 2C 10224114 10-000 00use

Service Manual
Screw Compressor
ASD SIGMA CONTROL 2

ASD_2C_10224114_10–000_00 USE
Original instructions
/KKW/SASD 2.01 en 01 ASD_2C_10224114_10-000_00
/KKW/SSC 2.00 01
20120315 085908
Contents
1 Regarding this Document

1.1 Using this document ......................................................................................................... 1
1.2 Further documents ........................................................................................................... 1
1.3 Copyright .......................................................................................................................... 1
1.4 Symbols and labels .......................................................................................................... 1
1.4.1 Warnings ............................................................................................................. 1
1.4.2 Potential damage warnings ................................................................................ 2
1.4.3 Other alerts and their symbols ............................................................................ 2
2 Technical Data
2.1 Nameplate ........................................................................................................................ 4
2.2 Options ............................................................................................................................. 4
2.3 Weight .............................................................................................................................. 5
2.4 Temperature ..................................................................................................................... 5
2.5 Ambient conditions ........................................................................................................... 5
2.6 Ventilation ........................................................................................................................ 6
2.7 Pressure ........................................................................................................................... 6
2.8 Delivery ............................................................................................................................ 7
2.9 Cooling Oil Recommendation .......................................................................................... 7
2.9.1 Basic Information ................................................................................................ 7
2.9.2 KAESER Lubricants ............................................................................................ 7
2.10 Cooling oil charge ............................................................................................................ 8
2.11 Motors and power ............................................................................................................ 9
2.11.1 Compressor motor .............................................................................................. 9
2.11.2 Fan motor ........................................................................................................... 9
2.12 Noise emission ................................................................................................................. 10
2.13 Power Supply ................................................................................................................... 10
2.14 Power Supply Specifications ............................................................................................ 10
2.15 Heat recovery ................................................................................................................... 12
2.15.1 Prepared for external heat recovery ................................................................... 12
2.15.2 Internal heat recovery ......................................................................................... 12
3 Safety and Responsibility
3.1 Basic instructions ............................................................................................................. 15
3.2 Specified use .................................................................................................................... 15
3.3 Improper use .................................................................................................................... 15
3.4 User's Responsibilities ..................................................................................................... 15
3.4.1 Observe statutory and universally accepted regulations .................................... 15
3.4.2 Qualified personnel ............................................................................................. 16
3.4.3 Adherence to inspection schedules and accident prevention regulations .......... 16
3.5 Dangers ............................................................................................................................ 16
3.5.1 Safely dealing with sources of danger ................................................................ 16
3.5.2 Safe machine operation ...................................................................................... 19
3.5.3 Organizational Measures .................................................................................... 21
3.5.4 Danger Areas ...................................................................................................... 21
3.6 Safety devices .................................................................................................................. 21
3.7 Safety Signs ..................................................................................................................... 21
3.8 Emergency situations ....................................................................................................... 23
3.8.1 Correct fire fighting ............................................................................................. 23
3.8.2 Treating injuries from handling cooling oil .......................................................... 24
3.9 Warranty ........................................................................................................................... 24
3.10 Environmental protection ................................................................................................. 24
3.11 Maintaining the silicone-free status ................................................................................. 25
4 Design and Function
4.1 Enclosure ......................................................................................................................... 27
Service Manual Screw Compressor

ASD_2C_10224114_10–000_00 USE ASD SIGMA CONTROL 2 i
Contents
4.2 Functional Description of the Machine ............................................................................. 27

4.2.1 Floating relay contacts ........................................................................................ 28
4.3 Freedom from silicon ........................................................................................................ 29
4.4 Options ............................................................................................................................. 29
4.4.1 Machine mountings ............................................................................................. 29
4.4.2 Water-cooling ...................................................................................................... 29
4.4.3 Cooling air filter mat ............................................................................................ 30
4.4.4 Heat recovery ..................................................................................................... 30
4.5 Operating modes and control modes ............................................................................... 31
4.5.1 Operating modes ................................................................................................ 31
4.5.2 Control modes .................................................................................................... 32
4.6 Safety devices .................................................................................................................. 33
4.7 Operating panel SIGMA CONTROL 2 ............................................................................ 34
5 Installation and Operating Conditions
5.1 Ensuring safety ................................................................................................................ 37
5.2 Installation conditions ....................................................................................................... 37
5.2.1 Determining location and clearances .................................................................. 37
5.2.2 Ensuring the machine room ventilation ............................................................... 38
5.2.3 Exhaust duct design ........................................................................................... 39
5.3 Using the Compressor to Supply A Compressed Air System. ......................................... 39
6 Installation
6.1 Ensuring safety ................................................................................................................ 40
6.2 Reporting Transport Damage ........................................................................................... 41
6.3 Connecting the machine with the compressed air network .............................................. 41
6.4 Connecting the power supply ........................................................................................... 41
6.5 Options ............................................................................................................................. 42
6.5.1 Anchoring the machine ....................................................................................... 42
6.5.2 Connecting the heat recovery system ................................................................ 42
7 Initial Start-up
7.1 Ensuring safety ................................................................................................................ 44
7.2 Instructions to be observed before commissioning or re-commissioning ......................... 45
7.3 Checking installation and operating conditions ................................................................ 45
7.4 Setting the overload protection relay ................................................................................ 46
7.5 Setting the motor overload protection relay ..................................................................... 46
7.6 Filling cooling oil into the airend ....................................................................................... 46
7.7 Activating and deactivating the MODULATING control .................................................... 47
7.8 Starting the machine for the first time .............................................................................. 48
7.9 Setting the set point pressure .......................................................................................... 48
7.10 Setting the display language ............................................................................................ 49
8 Operation
8.1 Switching on and off ......................................................................................................... 50
8.1.1 Switching on ....................................................................................................... 50
8.1.2 Switching off ....................................................................................................... 50
8.2 Switching off in an emergency and switching on again .................................................... 51
8.3 Switching on and off from a remote control center ........................................................... 51
8.4 Switching on and off with the clock .................................................................................. 52
8.5 Interpreting operation messages ...................................................................................... 53
8.6 Acknowledging alarm and warning messages ................................................................. 53
9 Fault Recognition and Rectification
9.1 Basic instructions ............................................................................................................. 56
9.2 Other Faults ..................................................................................................................... 56

ii ASD SIGMA CONTROL 2 ASD_2C_10224114_10–000_00 USE
Contents
10 Maintenance
10.1 Ensuring safety ................................................................................................................ 58
10.2 Following the maintenance plan ....................................................................................... 59
10.2.1 Logging maintenance work ................................................................................. 59
10.2.2 Resetting maintenance interval counters ............................................................ 59
10.2.3 Regular maintenance tasks ................................................................................ 59
10.2.4 Cooling oil changing interval ............................................................................... 60
10.2.5 Regular service tasks ......................................................................................... 61
10.3 Control cabinet: Clean or renew the filter mat .................................................................. 61
10.4 Cooler maintenance ......................................................................................................... 62
10.5 Cleaning or Renewing the Cooling Air Filter Mat ............................................................. 63
10.6 Maintaining the heat recovery system .............................................................................. 64
10.6.1 External heat recovery system ........................................................................... 65
10.6.2 Internal heat recovery ......................................................................................... 65
10.7 Changing the air filter ....................................................................................................... 65
10.8 Motor maintenance .......................................................................................................... 66
10.9 Checking the Coupling ..................................................................................................... 66
10.10 Testing the safety relief valve ........................................................................................... 67
10.11 Checking the overheating safety shutdown function ........................................................ 68
10.12 Checking the cooling oil level ........................................................................................... 68
10.13 Venting the machine (de-pressurizing) ............................................................................ 69
10.14 Replenishing the cooling oil ............................................................................................. 71
10.14.1 Venting the machine (de-pressurizing) ............................................................... 71
10.14.2 Topping up with cooling oil and trial run ............................................................. 72
10.15 Changing the cooling oil ................................................................................................... 73
10.16 Changing the oil filter ....................................................................................................... 77
10.17 Changing the oil separator cartridge ................................................................................ 79
10.18 Documenting maintenance and service work .................................................................. 82
11 Spares, Operating Materials, Service
11.1 Note the nameplate .......................................................................................................... 83
11.2 Ordering consumable parts and operating fluids/materials .............................................. 83
11.3 KAESER AIR SERVICE .................................................................................................. 83
11.4 Service Addresses ........................................................................................................... 84
11.5 Spare Parts for Service and Repair ................................................................................. 84
12 Decommissioning, Storage and Transport
12.1 Putting Out of Operation .................................................................................................. 87
12.2 Packing ............................................................................................................................ 87
12.3 Storage ............................................................................................................................. 87
12.4 Transport .......................................................................................................................... 88
12.4.1 Safety .................................................................................................................. 88
12.4.2 Transport with a forklift truck ............................................................................... 88
12.4.3 Transport with a crane ........................................................................................ 88
12.5 Disposal ........................................................................................................................... 89
13 Annex
13.1 Pipeline and instrument flow diagram (P+I diagram) ....................................................... 90
13.2 Pipe and Instrument Flow Diagram (P+I diagram): MODULATING control mode ........... 96
13.3 Dimensional drawing ........................................................................................................ 102
13.4 Electrical Diagram ............................................................................................................ 105

ASD_2C_10224114_10–000_00 USE ASD SIGMA CONTROL 2 iii
Contents

iv ASD SIGMA CONTROL 2 ASD_2C_10224114_10–000_00 USE
List of Illustrations
Fig. 1 Maximum relative humidity of inlet air ........................................................................................ 6

Fig. 2 Three-phase star (wye); 4 wire; grounded neutral ..................................................................... 10
Fig. 3 Three-phase star (wye); 3 wire; grounded neutral ..................................................................... 10
Fig. 4 Location of safety signs .............................................................................................................. 22
Fig. 5 Enclosure overview .................................................................................................................... 27
Fig. 6 Machine layout ........................................................................................................................... 28
Fig. 7 Machine mountings .................................................................................................................... 29
Fig. 8 Water-cooling (option K2) ........................................................................................................... 30
Fig. 9 Cooling air filter mat (option K3) ................................................................................................. 30
Fig. 10 Internal heat recovery (option W2/W3) ....................................................................................... 31
Fig. 11 Keys – overview ......................................................................................................................... 34
Fig. 12 Indicators .................................................................................................................................... 35
Fig. 13 RFID sensor field ........................................................................................................................ 36
Fig. 14 Recommended machine placement and dimensions [in] ........................................................... 38
Fig. 15 Compressed air piping ............................................................................................................... 41
Fig. 16 Connecting the heat recovery system ........................................................................................ 43
Fig. 17 Inlet valve filling port ................................................................................................................... 47
Fig. 18 Coupling ..................................................................................................................................... 47
Fig. 19 MODULATING control: Setting the shut-off valve ...................................................................... 48
Fig. 20 Switching on and off ................................................................................................................... 50
Fig. 21 Switching off in an emergency ................................................................................................... 51
Fig. 22 Switching on and off from a remote control center ..................................................................... 52
Fig. 23 Switching on and off with the clock ............................................................................................ 53
Fig. 24 Acknowledging messages .......................................................................................................... 54
Fig. 25 Switching cabinet ventilation ...................................................................................................... 62
Fig. 26 Clean cooler/radiator .................................................................................................................. 63
Fig. 27 Cooling air filter mat ................................................................................................................... 64
Fig. 28 Air filter maintenance .................................................................................................................. 66
Fig. 29 Checking the coupling ................................................................................................................ 67
Fig. 30 Checking the cooling oil level ..................................................................................................... 69
Fig. 31 Venting the machine ................................................................................................................... 70
Fig. 32 Replenishing the cooling oil ........................................................................................................ 71
Fig. 33 Changing the cooling oil, oil separator tank ............................................................................... 74
Fig. 34 Changing the cooling oil, oil cooler ............................................................................................. 75
Fig. 35 Changing the cooling oil, airend ................................................................................................. 76
Fig. 36 Changing the cooling oil, heat recovery system ......................................................................... 77
Fig. 37 Changing the oil filter .................................................................................................................. 78
Fig. 38 Changing the oil separator cartridge .......................................................................................... 80
Fig. 39 Transport with a forklift truck ...................................................................................................... 88
Fig. 40 Transport with a crane ................................................................................................................ 89

ASD_2C_10224114_10–000_00 USE ASD SIGMA CONTROL 2 v
List of Illustrations

vi ASD SIGMA CONTROL 2 ASD_2C_10224114_10–000_00 USE
List of Tables
Tab. 1 Danger levels and their definition (personal injury) .................................................................... 1

Tab. 2 Danger levels and their definition (damage to property) ............................................................ 2
Tab. 3 Nameplate .................................................................................................................................. 4
Tab. 4 Options ....................................................................................................................................... 4
Tab. 5 Machine weight .......................................................................................................................... 5
Tab. 6 Temperature ............................................................................................................................... 5
Tab. 7 Ambient conditions ..................................................................................................................... 5
Tab. 8 Overview Ventilation ................................................................................................................... 6
Tab. 9 Safety relief valve activating pressure ........................................................................................ 6
Tab. 10 Delivery ...................................................................................................................................... 7
Tab. 11 Cooling oil charge ...................................................................................................................... 8
Tab. 12 Cooling oil charge (Option W1) .................................................................................................. 8
Tab. 15 Compressor motor ...................................................................................................................... 9
Tab. 16 Compressor motor rated speed .................................................................................................. 9
Tab. 17 Fan motor ................................................................................................................................... 9
Tab. 18 Noise emission ........................................................................................................................... 10
Tab. 19 Supply 380V/3/60Hz ................................................................................................................... 11
Tab. 20 Supply 460V/3/60Hz ................................................................................................................... 11
Tab. 21 Supply 575V/3/60Hz ................................................................................................................... 11
Tab. 22 Heat capacity (Option W1) ......................................................................................................... 12
Tab. 23 Water quality specification .......................................................................................................... 12
Tab. 24 Heat exchanger specification (Option W2/W3) .......................................................................... 13
Tab. 25 Heat capacity (Option W2/W3) ................................................................................................... 13
Tab. 26 Flow rate / pressure loss (option W2) ......................................................................................... 13
Tab. 27 Flow rate / pressure loss (option W3) ......................................................................................... 14
Tab. 28 Danger Areas ............................................................................................................................. 21
Tab. 29 Safety Signs ............................................................................................................................... 22
Tab. 30 Energy-efficient control modes ................................................................................................... 32
Tab. 31 Operating modes under MODULATING control ......................................................................... 33
Tab. 32 Keys ........................................................................................................................................... 34
Tab. 33 Indicators .................................................................................................................................... 35
Tab. 34 RFID sensor field ........................................................................................................................ 36
Tab. 35 Re-commissioning after storage ................................................................................................. 45
Tab. 36 Installation and operating conditions checklist ........................................................................... 45
Tab. 37 MODULATING control: Setting the shut-off valve ...................................................................... 47
Tab. 38 Machine identification ................................................................................................................. 52
Tab. 39 Remote control identification ...................................................................................................... 52
Tab. 40 Machine identification ................................................................................................................. 53
Tab. 41 Other faults and actions ............................................................................................................. 56
Tab. 42 Regular maintenance tasks ........................................................................................................ 59
Tab. 43 Oil change intervals lubricants ................................................................................................... 60
Tab. 44 Regular service tasks ................................................................................................................. 61
Tab. 45 Logged maintenance tasks ........................................................................................................ 82
Tab. 46 Consumable parts ...................................................................................................................... 83

ASD_2C_10224114_10–000_00 USE ASD SIGMA CONTROL 2 vii
List of Tables

viii ASD SIGMA CONTROL 2 ASD_2C_10224114_10–000_00 USE
1.1 Using this document

1.1 Using this document
The operating manual is a component of the product. It describes the machine as it was at the time
of first delivery after manufacture.
➤ Keep the operating manual in a safe place throughout the life of the machine.
➤ Supply any successive owner or user with this operating manual.
➤ Please insert any amendment or revision of the operating manual sent to you.
➤ Enter details from the machine nameplate and individual items of equipment in the table in
chapter 2.
1.2 Further documents

Further documents included with this operating manual are:
■ Certificate of acceptance / operating instructions for the pressure vessel
■ Operating manual for SIGMA CONTROL 2
Missing documents can be requested from KAESER.

➤ Make sure all documents are complete and observe the instructions contained in them.
➤ Make sure you provide the data from the nameplate when ordering documents.
1.3 Copyright
This service manual is copyright protected. Queries regarding use or duplication of the documenta‐
tion should be referred to KAESER. Correct use of information will be fully supported.
1.4 Symbols and labels

➤ Please note the symbols and labels used in this document.
1.4.1 Warnings
Warning notices indicate dangers that may result in injury when disregarded.
Warning notices indicate three levels of danger identified by the corresponding signal word:
Signal term Meaning Consequences of disregard
DANGER Warns of an imminent danger Will result in death or severe injury
WARNING Warns of a potentially imminent danger May result in death or severe injury
CAUTION Warns of a potentially dangerous situation May result in a moderate physical injury
Tab. 1 Danger levels and their definition (personal injury)
Warning notices preceding a chapter apply to the entire chapter, including all sub-sections.
Example:

ASD_2C_10224114_10–000_00 USE ASD SIGMA CONTROL 2 1
The type and source of the imminent danger is shown here!

The possible consequences of ignoring a warning are shown here.
If you ignore the warning notice, the "DANGER" signal word indicates a lethal or severe in‐
jury will occur.
➤ The measures required to protect yourself from danger are shown here.
Warning notes referring to a sub-section or the subsequent action are integrated into the procedure
and numbered as an action.
Example:
1. The type and source of the imminent danger is shown here!
The possible consequences of ignoring a warning are shown here.
If you ignore the warning notice, the "WARNING" signal word indicates that a lethal or severe
injury may occur.
➤ The measures required to protect yourself from danger are shown here.
2. Always read and comply with warning instructions.
1.4.2 Potential damage warnings

Contrary to the warnings shown above, damage warnings do not indicate a potential personal in‐
jury.
Warning notices for damages are identified by their signal term.

Signal term Meaning Consequences of disregard
NOTE Warns of a potentially dangerous situation Damage to property is possible
Tab. 2 Danger levels and their definition (damage to property)
Example:
The type and source of the imminent danger is shown here!

Potential effects when ignoring the warning are indicated here.
➤ The protective measures against the damages are shown here.
➤ Carefully read and fully comply with warnings against damages.
1.4.3 Other alerts and their symbols

This symbol identifies particularly important information.

2 ASD SIGMA CONTROL 2 ASD_2C_10224114_10–000_00 USE
Material Here you will find details on special tools, operating materials or spare parts.
Precondition Here you will find conditional requirements necessary to carry out the task.
The conditions relevant to safety shown here will help you to avoid dangerous situations.
Option H1 ➤ This symbol denotes lists of actions comprising one stage of a task.
Operating instructions with several steps are numbered in the sequence of the operating steps.
Information relating to one option only are marked with an option code (e.g., H1 indicates that
this section applies only to machines with screw-in machine feet). Option codes used in this
service manual are explained in chapter 2.2.
Information referring to potential problems are identified by a question mark.
The cause is named in the help text ...
➤ ... as is a solution.
This symbol identifies important information or measures regarding the protection of the envi‐
ronment.
Further information Further subjects are introduced here.

2 Technical Data
2.1 Nameplate
2 Technical Data
2.1 Nameplate
The machine's nameplate provides the model designation and important technical information.
The nameplate is located on the outside of the machine:

■ above the cooler,
or
■ on the rear of the machine.
➤ Enter here the nameplate data as a reference:
Characteristic Value
Screw Compressor
Part no.
Year
Serial no.
psig
cfm
Voltage
Hz/RPM
Package FLA
Phase
HP
Wiring Diagram
FOR SERVICE, REFER TO EQUIPMENT NUMBER
Tab. 3 Nameplate
2.2 Options
The table contains a list of possible options.
➤ Enter options here as a reference.
Option Option code Exists?

Modulating control C1
Filter monitor option C2
SIGMA CONTROL 2 C3
Adjustable machine mountings H1
Cooling air filter mat K3
Transformer power supply for refrigerated dryer T2
Prepared for heat recovery W1
Heat recovery ΔT=45 F W2

2 Technical Data
2.3 Weight
Option Option code Exists?

Heat recovery ΔT=99 F W3
Tab. 4 Options
2.3 Weight
The weight given is the maximum. The actual weights of individual machines are dependent on
equipment fitted.
ASD 25 ASD 30 ASD 40S ASD 40

Weight [lb] 1320 1500 1520 1630
Tab. 5 Machine weight
2.4 Temperature
Minimum cut-in tempera‐ 40 40 40 40
ture [°F]
Typical airend discharge 150–200 150–200 150–200 150–200
temperature during oper‐
ation [°F]
Maximum airend dis‐ 230 230 230 230
charge temperature (au‐
tomatic safety shut-down)
[°F]
Tab. 6 Temperature
2.5 Ambient conditions

Maximum altitude AMSL* 3000 3000 3000 3000
[ft]
Permissible ambient tem‐ 40–115 40–115 40–115 40–115
perature [°F]
Cooling air temperature 40–115 40–115 40–115 40–115
[°F]
Inlet air temperature [°F] 40–115 40–115 40–115 40–115
* Higher altitudes are permissible only after consultation with the manufacturer.
Tab. 7 Ambient conditions

2 Technical Data
2.6 Ventilation
Fig. 1 Maximum relative humidity of inlet air

T Inlet air temperature [°F]
H Maximum relative humidity of inlet air [%]
2.6 Ventilation
The values given are minimum guide values.

Inlet aperture Z see fig‐ 5.4 6.5 7.5 8.6
ure 14 [ft2]
Forced ventilation with 4120 4709 5886 7063
exhaust fan:
Flow rate [cfm] at 0.4 in
wc
Tab. 8 Overview Ventilation
2.7 Pressure
Maximum working pressure: see nameplate
Maximum working pres‐ ASD 25 ASD 30 ASD 40S ASD 40

sure [psig]
125 155 155 155 155
175 230 230 230 230
217 232 232 232 232
Tab. 9 Safety relief valve activating pressure

2 Technical Data
2.8 Delivery
2.8 Delivery
Maximum working pres‐ ASD 25 ASD 30 ASD 40S ASD 40
sure [psig]
125 112 132 162 191
175 89 110 127 159
217 72 85 106 123
Tab. 10 Delivery
2.9 Cooling Oil Recommendation

A sticker showing the type of oil filled is located near the oil separator filler.
Information for ordering cooling oil can be found in chapter 11.
2.9.1 Basic Information

Lubrication of an air compressor is essential to reliable operation. Carbon and varnish can form in
compressor cooling oils. These deposits block the flow of lubricant and cause excessive wear and
failure of moving parts. Contamination of the lubricant can allow the formation of acids, causing ex‐
tensive internal corrosion. Water may be condensed decreasing the lubricity.
Lubricants in rotary compressors do much more than lubricate. During the compression process, it
acts as a sealant in the airend which is important for maximum efficiency. The lubricant also ab‐
sorbs much of the heat of compression to cool the airend and reduce the temperature of the com‐
pressed air. It’s not enough that a compressor cooling oil lubricates well, it must stand up to the
heat, pressure and contaminants that are present in every air compressor.
2.9.2 KAESER Lubricants

KAESER synthetic lubricants should be stored in a protected location to prevent contamination. Do
not re-use drums; flush and send to reconditioner.
Although the KAESER synthetic is not highly flammable, it will burn. While KAESER synthetic com‐
pressor cooling oil is less flammable than equal viscosity mineral oils, it cannot be classified as a
fire-resistant fluid. It has a flash point above 460 °F. Since the user has total control over the condi‐
tions of the compressor lubricant, he assumes total responsibility for its safe usage.
Material Safety Data Sheets are available for each lubricant from your authorized KAESER Service
representative.
Regardless of the lubricant selected, the KAESER SIGMA lubricants will separate readily from wa‐
ter. If condensate occurs it can easily be removed. Let the compressor sit so that any water can
drain back to the separator tank and separate to the bottom. See chapter 10.15 proper draining
procedure.
KAESER has several lubricants available that are specially formulated to match these demands.
They feature excellent lubricity, outstanding demulsibility (ability to separate from water), and long
life.
M-SERIES:
■ M-Series SIGMA compressor cooling oils are semi-synthetic lubricants.
■ M-Series SIGMA compressor cooling oils are the highest quality petroleum lubricants. M–460
is specially blended to provide reliable performance in KAESER screw compressors.

2 Technical Data
2.10 Cooling oil charge
S-SERIES:
■ S-Series SIGMA compressor cooling oils are synthetic lubricants.
■ S-Series SIGMA compressor cooling oils are formulated from the most advanced synthetic lu‐
bricants. These ”synthetic” lubricants begin as high quality petroleum feed stock. They are then
refined, processed and purified into fluids with very consistent molecular structure. These oils
are carefully blended to produce extremely consistant lubricants with superior properties.
SIGMA synthetic lubricants feature all the advantages of both PAO and diester fluids.
■ S-460 lubricant is recommended for compressors operating in ambient temperatures between
40 °F and 105 °F.
Specialty KAESER LUBRICANTS:

■ S-680 lubricant may be used when ambient temperatures are always between 70 °F and
105 °F.
■ FG-460 synthetic hydrocarbon based food grade lubricant is designed for use in rotary screw
compressors in the application where incidental food contact may occur with the discharge air.
This lubricant meets the requirements of the FDA Regulation 21 CFR §178.3570 and is
USDA H-1approved and NSF certified. FG-460 is approved for canning, food packing, meat
and poultry processing and other applications where incidental food contact may occur.
2.10 Cooling oil charge

The required cooling oil charge depends on the optional heat recovery system. For machines with
options W1, W2, or W3, the volume required additionally for the heat recovery must be added to
the charge.
Air-cooling

Fluid volume* [gal] 4.2 4.2 4.2 4.2
Topping up volume [qt] 2.1 2.1 2.1 2.1
(minimum–maximum)
* Plus the oil volume of the heat recovery system.
Tab. 11 Cooling oil charge
Option W1/W2/W3 Heat recovery
Option W1 The additional volume corresponds to the oil volume of the heat exchanger and the connecting
lines:
Additional charge vol‐
ume [qt]*
* Enter the volume required by your heat recovery system.
Tab. 12 Cooling oil charge (Option W1)

2 Technical Data
2.11 Motors and power
Option W2 ASD 25 ASD 30 ASD 40S ASD 40

Additional charge vol‐ 1.2 1.8 1.8 1.8
ume [qt]
Option W3 ASD 25 ASD 30 ASD 40S ASD 40

Additional charge vol‐ 1.2 1.8 1.8 1.8
ume [qt]
2.11 Motors and power

2.11.1 Compressor motor
Rated power [hp] 25 30 40 40
Degree of protection TEFC TEFC TEFC TEFC
Tab. 15 Compressor motor
Rated speed [rpm]:
Maximum working over‐ ASD 25 ASD 30 ASD 40S ASD 40

pressure [psig]
125 3550 3545 3550 3550
175 1780 3545 3550 3550
217 1780 1780 3550 3550
Tab. 16 Compressor motor rated speed
2.11.2 Fan motor

Rated power [hp] 0.75 0.75 0.75 0.75
Rated speed [rpm] 1080 1080 1080 1080
Degree of protection TEFC TEFC TEFC TEFC
Tab. 17 Fan motor

2 Technical Data
2.12 Noise emission
2.12 Noise emission

Noise emission [dB(A)] 66 67 67 69
Noise pressure level as per ISO 2151 and the basic standard ISO 9614-2, tolerance: ±3 dB(A) at
maximum machine working pressure
Tab. 18 Noise emission
2.13 Power Supply

Basic requirements
The machine is designed for an electrical supply according to National Electric Code (NEC) NEC–
670, particulary NFPA 79, edition 2007, section 4.3. In the absence of any user-specified alterna‐
tives, the limits given in these standards must be adhered to. Consult manufacturer for any other
specific power supply.
Three-phase
Do NOT operate package on any unsymmetrical power supply. Also do NOT operate package on
power supplies like, for example, a three-phase (open) delta or three-phase star with non-grounded
neutral.
The machine requires a symmetrical three-phase power supply transformer with a WYE configura‐
tion output as shown in Figure 2 and Figure 3. In a symmetrical three phase supply the phase an‐
gles and voltages are all the same.
Other power supplies are not suitable.
Fig. 2 Three-phase star (wye); 4 wire; grounded neutral
Fig. 3 Three-phase star (wye); 3 wire; grounded neutral
Further information Please contact authorized KAESER Service representative for options.
The electrical diagram 13.4 contains further specifications for electrical connection.
2.14 Power Supply Specifications

The following multi-strand copper core wires are given according to 2011 NEC 310.15, Ta‐
ble 310.16 for 40 °C ambient temperature.

2 Technical Data
2.14 Power Supply Specifications
If other local conditions prevail, like for example high temperature, the cross section should be
checked and adjusted according to 2011 NEC 110.14©, 220.3,310.15, Table 310.16, 430.6,
430.22, 430.24 and other local codes.
Dual element time delay fuses are selected according to 2011 NEC 240.6,430.52 and ta‐
bles 430.52, 430.248 and 430.250.
We strongly suggest using a separate copper conductor for the equipment GROUNDING. NEC
Table 250.122 will point out the ”minimum size”, however, we recommend a ground conductor the
same size as the power leads, if local codes allow.
Electrical connection data, in some cases, depends the maximum working pressure of the
machine.
Rated power supply 380V±10%/3/60Hz

Pre-fuse [A] 60 70 80 90
Supply 4x AWG4 4x AWG3 4x AWG3 4x AWG1
Consumption [A] 40* / 43 45 / 48** 54 64
* 125 psig
** 217 psig
Tab. 19 Supply 380V/3/60Hz
Rated power supply 460V±10%/3/60Hz

Pre-fuse [A] 50 60 60 70
Consumption [A] 33* / 36 37 / 40** 45 53
* 125 psig
** 217 psig
Rated power supply 575V ±10%, 3-ph, 60Hz

Pre-fuse [A] 40 45 50 60
Consumption [A] 26* / 29 30 / 32** 36 43
* 125 psig
** 217 psig

2 Technical Data
2.15 Heat recovery
2.15 Option W1/W2/W3

Heat recovery
2.15.1 Option W1
Prepared for external heat recovery
The quality of the heat transfer medium and its required flow rate depend on the type of heat
exchanger used.
Maximum permissible pressure loss in the cooling air circuit: 8.7 psi
Maximum heat capacity ASD 25 ASD 30 ASD 40S ASD 40

available*
[kW] 16.4 19.3 23.9 27.6
[MJ/h] 59 69 86 99
[kcal/h] 14101 16578 20567 23732
* With the combination valve set to open at 176°F.
Tab. 22 Heat capacity (Option W1)
2.15.2 Option W2/W3

Internal heat recovery
Water is generally the heat-receiving medium. The water must meet the specification given below
in order not to damage the heat exchanger.
➤ Consult an authorized KAESER service representative if you wish to use a different heat-
receiving medium.
Water quality specification
Characteristics/content Value
pH value 7.5–9
Hardness [ dH] 4.0–8.5
Chlorides (Cl) [mg/l] <150
Free chlorine gas (Cl2) [mg/l] <1
Sulphite (SO3) [mg/l] <1
Dissolved iron (Fe) [mg/l] <0.2
Hydrogen carbonate (HCO3) [mg/l] 70–300
Sulphate (SO4) [mg/l] <70
HCO3/SO4 >1
Electrical conductivity [µS/cm] 10–500
Ammonia (NH3) [mg/l] <2
Dissolved manganese (Mn) [mg/l] <0.1
Dissolved aluminum (Al) [mg/l] <0.2
Dissolved nitrate (NO3) [mg/l] <100

2 Technical Data
2.15 Heat recovery
Characteristics/content Value
Hydrogen sulfide (H2S) [mg/l] <0.05
Free aggressive carbon dioxide (CO2) [mg/l] <5
Glycol [%] <50
Solids (particle size) [mm] <0.1
Algae Not permitted
Tab. 23 Water quality specification
Heat exchanger specification

Material 1.4401 1.4401 1.4401 1.4401
Braze Copper (Cu) Copper (Cu) Copper (Cu) Copper (Cu)
Maximum working pres‐ 145 145 145 145
sure [psig]
(heat transfer medium)
Max. permissible dis‐ 212 212 212 212
charge temp. [°F]
Maximum flow volume 424 424 424 424
[cfm]
Unsuitable heat transfer Salt water
media Consult KAESER about water types.
Tab. 24 Heat exchanger specification (Option W2/W3)
Heat capacity
Maximum heat capacity ASD 25 ASD 30 ASD 40S ASD 40

available*
[kW] 16.4 19.3 23.9 27.6
[MJ/h] 59 69 86 99
[kcal/h] 14101 16578 20567 23732
* With the combination valve set to open at 176°F.
Tab. 25 Heat capacity (Option W2/W3)
Option W2 Heating up from 113°F to 158°F (ΔT=45°F)

Flow rate [gpm] 2.51 2.95 3.70 4.62
Pressure drop [psi] <2.2 <2.2 <2.9 <2.9
Tab. 26 Flow rate / pressure loss (option W2)

2 Technical Data
2.15 Heat recovery
Option W3 Heating up from 59°F to 158°F (ΔT=99 ° F)

Flow rate [gpm] 1.10 1.32 1.63 1.89
Pressure drop [psi] <1.5 <1.5 <1.5 <1.5
Tab. 27 Flow rate / pressure loss (option W3)

3.1 Basic instructions

The machine is manufactured to the latest engineering standards and acknowledged safety regula‐
tions. Nevertheless, dangers can arise through its operation:
■ danger to life and limb of the operator or third parties,
■ damages to the machine and other material assets.
Disregard of warning or safety instructions can cause serious injuries!
➤ Use this machine only if it is in a technically perfect condition and only for the purpose for
which it is intended; observe all safety measures and the instructions in the service manual.
➤ Immediately rectify (have rectified) any faults that could be detrimental to safety!
3.2 Specified use

The machine is intended solely for generating compressed air for industrial use. Any other use is
considered incorrect. The manufacturer is not liable for any damages that may result from incorrect
use. The user alone is liable for any risks incurred.
➤ Keep to the specifications listed in this service manual.
➤ Operate the machine only within its performance limits and under the permitted ambient condi‐
tions.
➤ Do not use compressed air for breathing purposes unless it is specifically treated.
➤ Do not use compressed for any application that will bring it into direct contact with food prod‐
ucts unless it is specifically treated.
3.3 Improper use

Improper usage can cause damage to property and/or (severe) injuries.
➤ Only use the machine as intended.
➤ Never direct compressed air at persons or animals.
➤ Use hot cooling air for heating purposes only if there is no risk to the health of humans or ani‐
mals. If necessary, hot cooling air should be treated by suitable means.
➤ Do not allow the machine to take in toxic, acidic, flammable of explosive gases or vapors.
➤ Do not operate the machine in areas in which specific requirements with regard to explosion
protection are in force.
3.4 User's Responsibilities

3.4.1 Observe statutory and universally accepted regulations
This is, for example, nationally applied European directives and/or valid national legislation, safety
and accident prevention regulations.
➤ Observe relevant statutory and accepted regulations during installation, operation and mainte‐
nance of the machine.

3.5 Dangers
3.4.2 Qualified personnel

These are people who, by virtue of their training, knowledge and experience as well as their knowl‐
edge of relevant regulations can assess the work to be done and recognize the possible dangers
involved.
Authorized operators possess the following qualifications:

■ are of legal age,
■ are conversant with and adhere to the safety instructions and sections of the service manual
relevant to operation,
■ have received adequate training and authorization to operate electrical and compressed air de‐
vices.
■ Additional qualifications for compressors with refrigeration dryers:
─ Adequate training and authorization on refrigeration devices.
Authorized installation and maintenance personnel have the following qualifications:

■ are of legal age,
■ have read, are conversant with and adhere to the safety instructions and sections of the ser‐
vice manual applicable to installation and maintenance,
■ are fully conversant with the safety concepts and regulations of electrical and compressed air
engineering,
■ are able to recognize the possible dangers of electrical and compressed air devices and take
appropriate measures to safeguard persons and property,
■ have received adequate training and authorization for the safe installation and maintenance on
this equipment.
■ Additional qualifications for compressors with refrigeration dryers:
─ fully conversant with the safety concepts and regulations concerning refrigeration devices,
─ must be able to recognize the possible dangers of refrigeration devices and take appropri‐
ate measures to safeguard persons and property.
➤ Ensure that operating, installation and maintenance personnel are qualified and authorized to
carry out their tasks.
3.4.3 Adherence to inspection schedules and accident prevention regulations

The machine may be subject to local inspection schedules.
3.5 Dangers
Basic instructions
The following describes the various forms of danger that can occur during machine operation.
Basic safety instructions are found in this service manual at the beginning of each chapter in the
section entitled 'Safety'.
Warning instructions are found before a potentially dangerous task.
3.5.1 Safely dealing with sources of danger

The following describes the various forms of danger that can occur during machine operation.

3.5 Dangers
Electricity
Touching voltage carrying components can result in electric shocks, burns or death.
➤ Allow only qualified and authorized electricians or trained personnel under the supervision of a
qualified and authorized electrician to carry out work on electrical equipment according to elec‐
trical engineering regulations.
➤ Before commissioning or re-commissioning the machine, the user must ensure adequate pro‐
tection against electric shock from direct or indirect contact.
➤ Before starting any work on electrical equipment:
Switch off and lock out the power supply isolator and verify the absence of any voltage.
➤ Switch off any external power sources.
These could be connections to floating relay contacts or the electrical machine heating, for ex‐
ample.
➤ Use fuses corresponding to machine power.
➤ Check regularly that all electrical connections are tight and in proper condition.
Forces of compression
Compressed air is contained energy. Uncontrolled release of this energy can cause serious injury
or death. The following information concerns work on components that could be under pressure.
➤ Close shut-off valves or otherwise isolate the machine from the distribution network to ensure
that no compressed air can flow back into the machine.
➤ Depressurize all pressurized components and enclosures.
➤ Do not carry out welding, heat treatment or mechanical modifications on pressurized compo‐
nents (e.g. pipes and vessels) as this influences the component's resistance to pressure.
The safety of the machine is then no longer ensured.
Compressed air quality
The composition of the compressed air must be suitable for the actual application in order to pre‐
clude health and life-threatening dangers.
➤ Use appropriate systems for air treatment before using the compressed air from this machine
as breathing air and/or for the processing of food products.
➤ Use food-grade cooling oil whenever compressed air is to come into contact with food prod‐
ucts.
Spring forces
Springs under tension or compression store energy. Uncontrolled release of this energy can cause
serious injury or death.
Minimum pressure / check valves, safety relief valves and inlet valves are powerfully spring-loaded.
➤ Do not open or dismantle any valves.
Rotating components
Touching the fan wheel, the coupling or the belt drive while the machine is switched on can result
in serious injury.
➤ Do not open the enclosure while the machine is activated.
➤ Switch off and lock out the power supply disconnecting device and verify the absence of any
voltage.

3.5 Dangers
➤ Wear close-fitting clothes and a hair net if necessary.

➤ Make sure all covers and safety guards are in place and secured before re-starting.
Temperature
High temperatures are generated during compression. Touching hot components may cause inju‐
ries.
➤ Avoid contact with hot components.
These include, for example, compressor airends or blocks, oil and compressed air lines, cool‐
ers, oil separator tanks, motors and machine heaters.
➤ Wear protective clothing.
➤ If welding is carried out on or near the machine, take adequate measures to prevent sparks or
heat from igniting oil vapors or parts of the machine.
Noise
The enclosure absorbs the machine noise to a tolerable level. This function will be effective only if
the enclosure is closed.
➤ Operate the machine only with intact sound insulation.
➤ Wear hearing protection if necessary.
The blowing-off of the safety relief valve can be particularly loud.
Operating fluids/materials
The used operating fluids and materials can cause adverse health effects. Suitable safety meas‐
ures must be taken in order to prevent injuries.
➤ Strictly forbid fire, open flame and smoking.
➤ Follow safety regulations when dealing with oils, lubricants and chemical substances.
➤ Avoid contact with skin and eyes.
➤ Do not inhale oil mist or vapor.
➤ Do not eat or drink while handling cooling and lubricating fluids.
➤ Keep suitable fire extinguishing agents ready for use.
➤ Use only KAESER approved operating materials.
Unsuitable spare parts
Unsuitable spare parts compromise the safety of the machine.

➤ Use only spare parts approved by the manufacturer for use in this machine.
➤ Use only genuine KAESER replacement parts on pressure bearing parts.
Conversion or modification of the machine
Modifications, additions to and conversions of the machine or the controller can result in unpredict‐
able dangers.
➤ Do not convert or modify the machine!
➤ Obtain written approval by the manufacturer prior to any technical modification or expansion of
the machine, the controller, or the control programs.

3.5 Dangers
Extending or modifying the compressor station
If dimensioned appropriately, safety relief valves reliably prevent an impermissible rise in pressure.
New dangers may arise if you modify or extend the compressed air station.
➤ When extending or modifying the compressed air system:
Check the blow-off capacity of safety relief valves on air receivers and compressed air lines
before installing a new machine.
➤ If the blow-off capacity is insufficient:
Install safety relief valves with larger blow-off capacity.
3.5.2 Safe machine operation

The following is information supporting you in the safe handling of the machine during individual
product life phases.
Personal protective equipment
When working on the machine you may be exposed to dangers that can result in accidents with
severe adverse health effects.
➤ Wear protective clothing as necessary.
Suitable protective clothing (examples):

■ Safety workwear
■ Protective gloves
■ Safety boots
■ Eye protection
■ Ear protection
Transporting
The weight and size of the machine require safety measures during its transport to prevent acci‐
dents.
➤ Use suitable lifting gear that conforms to local safety regulations.
➤ Allow transportation only by personnel trained in the safe movement of loads.
➤ Attach lifting gear only to suitable lifting points.
➤ Be aware of the center of gravity to avoid tipping.
➤ Make sure the danger zone is clear of personnel.
➤ Do not step onto machine components to climb up the machine.
Assembly
➤ Only use only electrical cables that are suitable and approved for the surroundings and electri‐
cal loads applied.
➤ Never dismantle compressed air pipes until they are fully vented.
➤ Only use pressure lines that are suitable and approved for the maximum working pressure and
the intended medium.
➤ Do not allow connection pipes to be placed under mechanical stress.
➤ Do not induce any forces into the machine via the connections, so that the compressive forces
must be balanced by bracing.

3.5 Dangers
Positioning
A suitable installation location for the machine prevents accidents and faults.
➤ Install the machine in a suitable compressor room.
➤ Ensure sufficient and suitable lighting such that the display can be read and work carried out
comfortably and safely.
➤ Ensure accessibility so that all work on the machine can be carried out without danger or hin‐
drance.
➤ If installed outdoors, the machine must be protected from frost, direct sunlight, dust, rain and
splashing water.
➤ Do not operate in areas in which specific requirements regarding explosion protection are in
force.
➤ Ensure adequate ventilation.
➤ Place the machine in such a manner that the working conditions in its environment are not im‐
paired.
➤ Comply with limit values for ambient temperature and humidity.
➤ The intake air must not contain any damaging contaminants,
Damaging contaminants are for instance: explosive or chemically instable gases and vapors,
acid or base forming substances such as ammonia, chlorine or hydrogen sulfide.
➤ Do not position the machine in warm cooling outlet air from other machines.
Commissioning, operation and maintenance
During commissioning, operation and maintenance you may be exposed to dangers resulting from,
e.g., electricity, pressure and temperature. Careless actions can cause accidents with severe ad‐
verse effects for your health.
➤ Allow maintenance work to be carried out only by authorized personnel.
➤ Wear close-fitting, flame-resistant clothing. Wear protective clothing as necessary.
➤ Switch off and lock out the power supply isolating device and verify the absence of voltage.
➤ Check that there is no voltage on floating relay contacts.
➤ Close shut-off valves or otherwise isolate the machine from the compressed air network to en‐
sure that no compressed air can flow back into the machine.
➤ De-pressurize all pressurized components and enclosures.
➤ Allow the machine to cool down.
➤ Do not open the cabinet while the machine is switched on.
➤ Use only spare parts approved by KAESER for use in this machine.
➤ Carry out regular inspections:
for visible damages,
of safety installations,
of the EMERGENCY STOP command device,
of any components requiring monitoring.
➤ Pay particular attention to cleanliness during all maintenance and repair work. Cover compo‐
nents and openings with clean cloths, paper or tape to keep them clean.
➤ Do not leave any loose components, tools or cleaning rags on or in the machine.
➤ Components removed from the machine can still be dangerous.
Do not attempt to open or destroy any components taken from the machine.

3.6 Safety devices
De-commissioning, storage and disposal
Improper handling of old operating fluids and components represent a danger for the environment.
➤ Drain off fluids and dispose of them according to environmental regulations.
These include, for example, compressor oil and cooling water.
➤ Have refrigerant disposed of by authorized bodies only.
➤ Dispose of the machine in accordance with local environmental regulations.
3.5.3 Organizational Measures

➤ Designate personnel and their responsibilities.
➤ Give clear instructions on reporting faults and damage to the machine.
➤ Give instructions on fire reporting and fire-fighting measures.
3.5.4 Danger Areas

The table gives information on the areas dangerous to personnel.
Only authorized personnel may enter these areas.
Activity Danger area Authorized personnel

Transport Within a 10 ft radius of the machine. Installation personnel for transport
preparation.
No personnel during transport.
Beneath the lifted machine. No personnel!
Installation Within the machine. Installation personnel
Within 3 ft radius of the machine and its sup‐
ply cables.
Operation Within a 3 ft radius of the machine. Operating personnel
Maintenance Within the machine. Maintenance personnel
Within a 3 ft radius of the machine.
Tab. 28 Danger Areas
3.6 Safety devices

Various safety devices ensure safe working with the machine.
➤ Do not change, bypass or disable safety devices.
➤ Regularly check safety devices for their correct function.
➤ Do not remove or obliterate labels and notices.
➤ Ensure that labels and notices are clearly legible.
Further information More information on safety devices is contained in chapter 4, section 4.6.
3.7 Safety Signs

The diagram shows the positions of safety signs on the machine. The table lists the various safety
signs used and their meanings.

3.7 Safety Signs
Fig. 4 Location of safety signs
Item Symbol Meaning

8 Danger of fatal injury from touching electrically live components!
➤ Switch off and lock out the supply disconnecting device and check that no volt‐
age is present.
9 Machine starts automatically!
Severe injury could result from rotating components, electrical voltage and air pres‐
sure.
➤ Isolate from the power supply and lock out before opening any machine enclo‐
sure or guard.
11 Injury and/or contamination can result from breathing compressed air!
Contamination of food can result from using untreated compressed air for food proc‐
essing!
➤ Never breathe untreated compressed air.
➤ Air from this compressor must meet OSHA 29CFR1910.134 and
FDA 21CFR178.3570 standards, if used for breathing or food processing. Use
proper compressed air treatment.
12 Rotating parts!
Severe injury, especially of the eyes, could result while the fan is rotating.
➤ Prevent all materials from falling into the fan guard.
➤ Never work over the running machine.
13 Hot surface can cause burns!
➤ Let the machine cool down.
➤ Wear long-sleeved garments (not synthetics such as polyester) and protective
gloves.
23 Serious injury or death can result from loosening or opening component that is un‐
der pressure and heavily spring loaded!
➤ Do not open or dismantle the valve.
➤ Call for authorized KAESER Service representative if a fault occurs.

3.8 Emergency situations
Item Symbol Meaning

24 Serious injury or death can result from loosening or opening component under pres‐
sure!
➤ Secure that machine keeps de-pressurized.
➤ Check that machine is de-pressurized.
25 Ear damage and burns can result from loud noise and/or oil mist when the safety
relief valve opens!
➤ Wear ear protection and protective clothing.
➤ Close all access doors and cover panels.
27 Risk of electric shock!
If the interrupter has tripped current-carrying components of the controller should be
examined and replaced if damaged to reduce the risk of fire or electric shock.
28 Risk of electric shock!
To maintain overcurrent short-circuit, and ground-fault protection, the manufactur‐
er's instructions for setting the interrupter must be followed to reduce the risk of fire
or electric shock.
Tab. 29 Safety Signs
3.8 Emergency situations

3.8.1 Correct fire fighting
Suitable measures
Calm and prudent action can safe lives in the event of a fire.
➤ Keep calm.
➤ Give the alarm.
➤ Shut off supply lines if possible.
Mains disconnecting device (all poles)
Cooling water (if present)
Heat recovery (if present)
➤ Warn and move endangered personnel to safety.
➤ Help incapacitated persons.
➤ Close the doors.
➤ When trained accordingly: Attempt to extinguish the fire.
Extinguishing substances
➤ Suitable extinguishing media:

Foam
Carbon dioxide
Sand or soil
➤ Unsuitable extinguishing media:
Strong jet of water

3.9 Warranty
3.8.2 Treating injuries from handling cooling oil

Eye contact:
Cooling oil can cause irritation.

➤ Rinse open eyes thoroughly for a few minutes under running water.
➤ Seek medical help if irritation persists.
Skin contact:
Cooling oil may irritate after prolonged contact.

➤ Wash thoroughly with skin cleaner, then with soap and water.
➤ Contaminated clothing should be dry-cleaned before reuse.
Inhalation:
Cooling oil mist may make breathing difficult.

➤ Clear air passages of oil mist.
➤ Seek medical help if difficulty with respiration continues.
Ingestion
➤ Wash out the mouth immediately.

➤ Do not induce vomiting.
➤ Seek medical aid.
3.9 Warranty
This service manual contains no independent warranty commitment. Our general terms and condi‐
tions of business apply with regard to warranty.
A condition of our warranty is that the machine is used for the purpose for which it is intended un‐
der the conditions specified.
Due to the multitude applications for which the machine is suitable the obligation lies with the user
to determine its suitability for his specific application.
In addition, we accept no warranty obligation for:

■ the use of unsuitable parts or operating materials,
■ unauthorized modifications,
■ incorrect maintenance,
■ incorrect repair.
Correct maintenance and repair includes the use of original spare parts and operating materials.
➤ Obtain confirmation from KAESER that your specific operating conditions are suitable.
3.10 Environmental protection

The operation of this machine may cause dangers for the environment.
➤ Do not allow cooling oil to escape to the environment or into the sewage system.

3.11 Maintaining the silicone-free status
➤ Store and dispose of operating materials and replaced parts in accordance with local environ‐
mental protection regulations.
➤ Observe national regulations.
This applies particularly to parts contaminated with compressor cooling oil.

The following describes measures ensuring that the compressed air from the machine is free of sili‐
cone.
This machine is silicone-free!

Incorrect treatment of the machine can lead to contamination of the compressed air.
➤ Follow the instructions in the service manual.
➤ Only authorized KAESER Service personnel should carry out service work.
installation and commissioning,
➤ Check the machine's identification marks:

■ Use only silicone-free components for installation and connection to the compressed air
network.
■ Wear silicone-free gloves during installation and commissioning work.
■ Make sure that all general materials and tools used for installation are free of silicone.
■ Any safety devices used are to be free of silicone.
■ Do not put the machine into operation until it is certain that it has been correctly installed.
Operation
➤ Never operate the machine in anything but an environment free of silicone.

➤ If the air/gas inlet to the machine is from a supply network, the user is responsible for ensuring
that it is not a source of silicone.
Maintenance
➤ Always use silicone-free working gloves to carry out maintenance, repair and cleaning work.
➤ Use only silicone-free detergents and cleaning agents when cleaning the machine.
➤ Make sure that all general materials and tools used for installation are free of silicone.
➤ Have all maintenance and repair work on components that come into direct contact with the
compressed air or the oil flow carried out by qualified personnel authorized by KAESER.
Spare parts
➤ Maintenance and spare parts that come into contact with the airflow or oil flow:
■ use only genuine KAESER silicone-free parts,
■ always specify "silicone-free" when ordering parts.

Packaging, storage
➤ Use natural wood, plywood or plastic sheeting that does not contain any silicone additives of
any kind.
➤ Store unpacked machines or components in an environment free of silicone.
➤ Use silicone-free plastic sheeting to protect against moisture.

4.1 Enclosure

4.1 Enclosure
Fig. 5 Enclosure overview

1 Control cabinet door
2 Latch
3 Panel (removable)
The enclosure, when closed, serves various functions:

■ Sound insulation
■ Protection against contact with components
■ Cooling air flow
The enclosure is not suitable for the following uses:

■ Walking on, standing or sitting on.
■ As resting place or storage of any kind of load.
Safe and reliable operation is only assured with the enclosure closed.
Access doors are hinged to swing open and removable panels can be lifted off.
Latches are released by a key supplied with the machine.
4.2 Functional Description of the Machine

Functional description using an air-cooled machine as an example.

4.2 Functional Description of the Machine
Fig. 6 Machine layout

1 Inlet valve 6 Control cabinet
2 Minimum pressure/check valve 7 Oil separator tank
3 Drive motor 8 Air filter
4 Oil filter 9 Oil/air cooler
5 Airend
Ambient air is cleaned as it is drawn in through the filter 8 .

The air is then compressed in the airend 5 .
The airend is driven by an electric motor 3 .
Cooling oil is injected into the airend. It lubricates moving parts and forms a seal between the ro‐
tors themselves and between them and the airend casing. This direct cooling in the compression
chamber ensures a very low airend discharge temperature.
Cooling oil recovered from the compressed air in the oil separator tank 7 gives up its heat in the oil
cooler 9 . The oil then flows through the oil filter 4 and back to the point of injection. Pressure with‐
in the machine keeps the oil circulating. A separate pump is not necessary. A thermostatic valve
maintains optimum cooling oil temperature.
Compressed air, freed of cooling oil in the oil separator tank 7 , flows through the minimum pres‐
sure/check valve 2 into the air cooler 9 . The minimum pressure/check valve ensures that there is
always a minimum internal air pressure sufficient to maintain cooling oil circulation in the machine.
The air cooler brings down the compressed air temperature of only 5 to 10 K above ambient. Most
of the moisture carried in the air is removed during this cooling process.
4.2.1 Floating relay contacts

Floating relay contacts are provided for the transfer of signals, messages.
Information on location, loading capacity and type of message or signal is found in the electrical
diagram.
If the floating relay contacts are connected to an external voltage source, voltage may be
present even when the machine is isolated from the power supply.

4.3 Freedom from silicon
4.3 Freedom from silicon

The machine is delivered in a completely silicone-free state.
This applies to all work involving:
■ installation,
■ initial start-up,
■ operation,
■ maintenance,
■ ordering spare parts,
■ packing and storage.
➤ The instructions given for maintaining the silicon-free status in chapter3.11 must be followed to
ensure that the compressed air/gas delivered is free of silicone.
4.4 Options
The options available for your machine are described below.
4.4.1 Option H1
Machine mountings
These mountings allow the machine to be anchored firmly to the floor.
Fig. 7 Machine mountings
4.4.2 Option K2
Water-cooling
Plate heat exchangers in stainless steel are used for water-cooled machines. An additional con‐
tainer supplements the cooling oil circuit.
This additional container is omitted on machines with heat recovery.

4.4 Options
Fig. 8 Water-cooling (option K2)

1 Oil cooler 3 Cooling water connection
2 Air cooler 4 Cooling water connection
4.4.3 Option K3
Cooling air filter mat
The mat filters the cooling air and keeps the cooler surface clean.
Fig. 9 Cooling air filter mat (option K3)

1 Cooling air filter mat
4.4.4 Option W1/W2/W3

Heat recovery
The cooling oil circuit includes 2 valves that regulate the oil temperature.
■ Combination valve: oil temperature regulator for the oil cooler.
■ Thermostatic valve: oil temperature regulator for the heat recovery system.
The cooling oil is kept at the ideal temperature for machine operation.
The thermostatic valve opens first so that heat is given up to the heat recovery system. If the heat
recovery system cannot carry away enough heat, the combination valve opens to allow hot oil
through the oil cooler circuit.
Operation:
combination valve opening temperature = thermostatic valve opening temperature
The available heat to be recovered depends on the operating conditions of the machine.

4.5 Operating modes and control modes
Option W1 Prepared for external heat recovery
Connections are provided for an external system to recover surplus heat.

The thermostatic valve does not function when the machine is delivered. The necessary working
element must be installed when installing the heat recovery system.
If necessary, the working element in the combination valve can be exchanged for one with higher
opening temperature. The opening temperature depends on operating and ambient conditions.
Working elements are marked with their opening temperature [°C].
If the cooling oil temperature is too low, condensate can form and damage the machine.
➤ Consult KAESER Service on components and layout to ensure a fully function cooling
and heat recovery system.
Option W2/W3 Internal heat recovery
A plate-type heat exchanger is installed for internal heat recovery.

The plate-type heat exchanger transfers heat from the cooling oil to a heat-receiving medium.
Both oil temperature regulators are equipped with working elements that ensure trouble-free func‐
tioning of the cooling and heat recovery systems.
Fig. 10 Internal heat recovery (option W2/W3)

1 Plate-type heat exchanger

4.5.1 Operating modes
The machine operates in the following modes:
■ LOAD:
The inlet valve is open. The airend delivers compressed air to the distribution network.
The drive motor runs under full load.
■ IDLE:
The inlet valve is closed. The minimum pressure/check valve shuts off the oil separator from
the distribution network. The venting valve is open.
A small volume of air circulates through the bleed hole in the inlet valve, through the airend
and back to the inlet valve via the venting valve.
The compressor motor runs without load and draws little current.

■ STANDSTILL:
The inlet valve is closed. The minimum pressure/check valve shuts off the oil separator from
the distribution network. The venting valve is open.
The compressor motor is stopped.
Option C1 ■ MODULATING CONTROL:
With the help of a control valve (the proportional controller) the degree of opening of the inlet
valve is steplessly varied in response to the air demand. The airend delivers compressed air to
the distribution network.
The load and power consumption of the drive motor rises and falls with the air demand.
The regulating valve is factory set. The setting should not be changed without consultation with
an authorized KAESER distributor.
4.5.2 Control modes

Using the selected control mode, the controller switches the machine between its various opera‐
tional states in order to compensate for air being drawn of by consumers and maintain system
pressure between the set minimum and maximum values. The control mode also rules the degree
of energy efficiency of the machine.
The machine-dependant venting phase between the LOAD and STANDSTILL operating modes en‐
sures load changes at minimum material stresses.
The controller SIGMA CONTROL 2 can operate in the following modes:

■ DUAL
■ QUADRO
■ VARIO
Option C1 ■ MODULATING control
Energy-efficient control modes for various applications:

Application Recommended
control mode
Compressed air station with one machine or several machines with com‐ VARIO
parable delivery
Machine for peak load in a compressed air station DUAL
Machine for intermediate load in a compressed air station VARIO
Machine for basic load in a compressed air station QUADRO
Tab. 30 Energy-efficient control modes
The SIGMA CONTROL 2 controller is factory set to QUADRO control mode unless specifically
ordered otherwise.
DUAL
In the DUAL control mode, the machine is switched back and forth between LOAD and IDLE to
maintain the machine working pressure between the preset minimum and maximum values. When
maximum pressure is reached, the machine switches to IDLE. When the preset idling time has
elapsed the machine is STOPPED.
The idling time is factory preset according to the maximum starting frequency of the compressor
motor. The shorter the idle period setting, the sooner (and more frequently) the motor is stopped.

4.6 Safety devices
QUADRO
In contrast to the DUAL regulating mode, the machine will switch from LOAD to STANDSTILL in
QUADRO mode after periods with low compressed air consumption.
After periods with a high compressed air consumption, the machine will switch from LOAD to
STANDSTILL after passing through IDLE.
In this control mode, the controller requires two specified times: The running time and the idle /
standstill time.
The shorter these times are set, the sooner (and more frequently) the motor is stopped.
VARIO
The VARIO mode is based on the DUAL control mode. The difference to DUAL is that the idle time
is automatically lengthened or shortened to compensate for higher or lower machine starting fre‐
quencies.
Option C1 MODULATING control
The MODULATING control completes the aforementioned control types. It continuously changes
the delivery volume within the machine's control range.
Compressed air demand Operating modes

rises MODULATING
LOAD
falls MODULATING
IDLE
STANDSTILL
Tab. 31 Operating modes under MODULATING control
4.6 Safety devices

The following safety devices are provided and may not be modified in any way.
■ EMERGENCY STOP control device:
Stops the machine immediately in an emergency situation. The motor remains stopped. The
pressure system is vented.
■ Pressure relief valve:
The pressure relief valve protects the system against excessive pressure. It is factory set.
■ Safety pressure switch (machine with refrigerated dryer):
The safety pressure switch protects the refrigerant circuit against excessive pressure. It cannot
be set.
■ Enclosures and guards for moving parts and electrical connections
Protect against accidental contact.

4.7 Operating panel SIGMA CONTROL 2

Keys
Fig. 11 Keys – overview
Item Name Function

1 «OFF» Switch off the machine.
2 «ON» Switch on the machine.
3 «Escape» Returns to the next higher menu option level.
Exits the edit mode without saving.
4 «Enter» Jumps to the selected menu option.
Exits the edit mode and saves.
5 «DOWN» Scrolls down the menu options.
Reduces a parameter value.
6 «Right» Jumps to the right.
7 «Left» Jumps to the left.
8 «UP» Scrolls up the menu options.
Increases a parameter value.
9 «Events and information» Operating mode:
Displays the event memory.
10 «Acknowledgement» Acknowledges alarms and warning messages.
If permissible: Resets the fault counter (RESET).
11 «LOAD/IDLE» Toggles the compressor between LOAD and IDLE operating
modes.
12 «Remote control» Switches remote control on and off.
13 «Shift clock» Switches clock control on and off.
Tab. 32 Keys

Indicators
Fig. 12 Indicators
Item Name Function

14 Indicator field or dis‐ Graphic display with 8 lines and 30 characters.
play
15 Fault Flashes red when an alarm occurs.
Lights continuously when acknowledged.
16 Communication Continuous red illumination if a communication connection (Ethernet,
USS, COM modules) has a fault.
17 Warning Flashes in yellow in the following events:
■ maintenance work due,
■ Warning message
Lights continuously when acknowledged.

18 Control voltage Lights green when the power supply is switched on.
19 LOAD Lights green when the compressor is running under LOAD.
20 IDLE Lights green when the compressor is running in IDLE.
Flashes when the «LOAD/IDLE» toggle key is pressed.
21 Remote control The LED lights when the machine is in remote control.
22 Shift clock The LED lights when the machine is in clock control.
23 Machine ON Lights green when the machine switched on.
Tab. 33 Indicators

RFID sensor field
RFID is the abbreviation for “Radio Frequency Indentification” and enables the identification of per‐
sons or objects.
Placing a suitable transponder in front of the RFID sensor field of the controller will automatically
activate the communication between transponder and SIGMA CONTROL 2 .
A suitable transponder is the EQUIPMENT CARD. Two of them have been provided with the ma‐
chine.
Typical application:
■ Users log on to the machine.
(no manual input of the password required.)
Fig. 13 RFID sensor field
Item Name Function

24 RFID RFID sensor field for the communication with a suitable RFID transponder.
Tab. 34 RFID sensor field
Further information More information about the use of RFID technology is provided in the SIGMA CONTROL 2 operat‐
ing manual.

5.1 Ensuring safety

5.1 Ensuring safety
The conditions in which the machine is installed and operated have a decisive effect on safety.
Warning instructions are located before a potentially dangerous task.
Disregard of warning instructions can cause serious injuries!
Complying with safety notes
Disregard of safety notes can cause unforeseeable dangers!

➤ Strictly forbid fire, open flame and smoking.
➤ If welding is carried out on or near the machine, take adequate measures to prevent sparks or
heat from igniting oil vapours or parts of the machine.
➤ Do not store inflammable material in the vicinity of the machine.
➤ The machine is not explosion-proof!
Do not operate in areas in which specific requirements with regard to explosion protection are
in force.
➤ Ensure sufficient and suitable lighting such that the display can be read and work carried out
comfortably and safely.
➤ Ensure that required ambient conditions are maintained.
Required ambient conditions may be:

■ Maintain ambient temperature and humidity
■ Ensure the appropriate composition of the air within the machine room:
─ clean with no damaging contaminants (e.g., dust, fibers, fine sand)
─ free of explosive or chemically unstable gases or vapors
─ free of acid/alkaline forming substances, particularly ammonia, chlorine or hydrogen sulfide.
5.2 Installation conditions

5.2.1 Determining location and clearances
The machine is intended for installation in an appropriate machine room. Information on distances
from walls and ventilation is given below.
The distances quoted are recommended distances and ensure unhindered access to all ma‐
chine parts.
➤ Please consult KAESER if you cannot comply with these recommendations.
Precondition The floor must be level, firm and capable of bearing the weight of the machine.

5.2 Installation conditions
Fig. 14 Recommended machine placement and dimensions [in]

A Exhaust fan
B Exhaust air duct
Z Inlet air opening
1. Ambient temperature too low.

Frozen condensate and highly viscous cooling oil can cause damage when starting the ma‐
chine.
➤ Make sure that the temperature of the machine is at least +37°F before starting.
➤ Heat the machine room adequately or install an auxiliary heater.
2. Ensure adequate lighting so that all work on the machine can be carried out without danger or
hindrance.
3. Ensure that the indicators can be read without glare and that the controller display cannot be
damaged by direct sunlight (UV radiation).
4. Ensure that all intake and exhaust apertures of the enclosure remain opened.
5. If installed outdoors, the equipment must be protected from frost, direct sunlight, dust and rain.
5.2.2 Ensuring the machine room ventilation

Adequate ventilation of the machine room has several tasks:
■ It prevents subatmospheric pressure in the machine room.
■ It evacuates the exhaust heat of the machine and thus ensures the required operating condi‐
tions.
➤ Consult with KAESER if you cannot ensure the conditions for an adequate ventilation of
the machine room.
1. Ensure that the volume of air flowing into the machine room is at least equivalent to that being
removed from it by the machine and exhaust fan.
2. Make sure that the machine and exhaust fan can only operate when the inlet aperture is ac‐
tually open.
3. Keep the inlet and exhaust apertures free of obstructions so that the cooling air can flow freely
through the room.
4. Ensure clean air in order to support the proper functioning of the machine.

5.3 Using the Compressor to Supply A Compressed Air System.
5.2.3 Exhaust duct design

At the cooling air inlet and exhaust, the machine can only overcome the air resistance resulting
from the duct design. Any additional air resistance will reduce airflow and deteriorate machine cool‐
ing.
➤ Consult with KAESER before deciding on:
■ Design of the exhaust air ducting
■ Transition between the machine and the exhaust air duct
■ Length of the ducting
■ Number of duct bends
■ Design of flaps or shutters
Further information Further information on the design of exhaust air ducts can be found in chapter 13.3.
5.3 Using the Compressor to Supply A Compressed Air System.

When the machine is connected to a compressed air system, the system operating pressure must
not exceed 232 psig.
Initial filling of a fully vented air network generally creates a very high rate of flow through air treat‐
ment devices. These conditions are detrimental to correct treatment. Air quality suffers.
To ensure maintenance of desired air quality when filling a vented compressed air system we rec‐
ommend the installation of an air main charging system.
➤ Please allow KAESER to advise on this subject.

6 Installation
6.1 Ensuring safety
6 Installation
6.1 Ensuring safety
Follow the instructions below for safe installation.

➤ Follow the instructions in chapter 3 'Safety and Responsibility'.
➤ Installation work may only be carried out by authorized personnel.
➤ Make sure that no one is working on the machine.
➤ Ensure that all service doors and panels are locked.
When working on live components
➤ Work on electrical equipment may only be carried out by authorized electricians.
When working on the compressed air system
or death. The following safety concerns relate to any work on components that could be under
pressure.
➤ Check all hose couplings in the compressed air system with a hand-held pressure gauge to en‐
sure that they all read 0 psig.
When working on the drive system
in serious injury.
Further information Details of authorized personnel are found in chapter 3.4.2.

Details of dangers and their avoidance are found in chapter 3.5.

6 Installation
6.2 Reporting Transport Damage
6.2 Reporting Transport Damage

1. Check the machine for visible and hidden transport damage.
2. Inform the carrier and the manufacturer in writing of any damage without delay.
6.3 Connecting the machine with the compressed air network

Condensate in the compressed air network can damage the piping:
➤ Install only corrosion-resistant pipes.
➤ Use fluoroelastomers as sealing material for seals.
➤ Note the electro-chemical voltage sequence.
➤ Consult with KAESER for suitable materials for the compressed air network.
Precondition The compressed air system is vented completely to atmospheric pressure.
Fig. 15 Compressed air piping

1 Axial compensator or flexible hose
2 Shut-off valve
➤ Do not induce any forces into the machine for which the compressive forces must be bal‐
anced by bracing.
1. Serious injury or death can result from loosening or opening components under
pressure.
➤ Depressurize all components and enclosures that are subjected to pressure.
2. A shut-off valve must be installed by the user in the connection line.
3. Connect the axial compensator or flexible hose.
Further information The dimensional drawing in chapter 13.3 provides the size and position of the connection ports.
6.4 Connecting the power supply

Precondition The power supply disconnecting device is switched off,
the device is locked off,
the absence of any voltage has been verified.
1. The power supply must only be connected by authorized installation personnel or an author‐
ized electrician.
2. Carry out safety measures as stipulated in relevant regulations and in national accident pre‐
vention regulations. In addition, observe the regulations of the local electricity supplier.

6 Installation
6.5 Options
3. Test the overcurrent protection cut-out to ensure that the time it takes to disconnect in re‐
sponse to a fault is within the permitted limit.
4. Select supply cable conductor diameters and fusing in accordance with local regulations.
5. The user must provide the machine with a lockable power supply disconnecting device.
This could be, for example, a load disconnect switch with fused input. If a circuit breaker is
used it must be suitable for the motor starting characteristics.
6. Check that the tappings on the control voltage transformer are connected according to the sup‐
ply voltage. If not, change the tappings to suit the power supply voltage.
7. Danger of fatal injury from electric shock!
➤ Switch off and lock out the power supply disconnecting device and verify the absence of
voltage.
8. Connect the machine to the power supply.
9. Ensure that the cabinet again complies with the requirements for degree of protection IP54.
Further information The electrical diagram in chapter 13.4 contains further details for the power supply connection.
6.5 Options
6.5.1 Option H1
Anchoring the machine
➤ Use appropriate fixing bolts to anchor the machine.
Further information Details of the fixing holes are contained in the dimensional drawing in chapter 13.3.
6.5.2 Option W1/W2/W3

Connecting the heat recovery system
➤ Take the electrochemical series into account and choose suitable materials for connec‐
tions.
➤ Keep the effect of pressure surges on the heat exchanger as low as possible.
➤ Install an expansion tank to act as a pulsation damper if pressure surges cannot be
avoided.
➤ Install appropriate regulating devices if the heat transfer medium is to be kept constant.
➤ Avoid very low inlet temperatures of the heat transfer medium as it can cause condensa‐
tion. If required, contact KAESER for suitable insulation measures.
Cooling oil in the heat-receiving medium!

Oil may contaminate the medium if a leak occurs.
➤ Do not use the heat-receiving medium as drinking water.
➤ Install the heat recovery system in accordance with the following specifications.
Further information The dimensional drawing in chapter 13.3 gives the flow direction, size and location of the connec‐
tion ports.

6 Installation
6.5 Options
6.5.2.1 Option W1
Connecting the external heat recovery system
An unsuitable heat exchanger or incorrect installation may adversely impact the cooling oil
circuit within the compressor. Damage to the machine will follow.
➤ Consult with KAESER on a suitable heat exchanger and have an authorized KAESER service
representative do the installation.
6.5.2.2 Option W2/W3

Connecting the internal heat recovery system
Connecting the internal heat recovery system
Fig. 16 Connecting the heat recovery system

A Outlet 12 Connection port with plug
B Inlet 17 Safety relief valve
10 Shut-off valve
1. The user is to provide the following fittings:

■ Dirt trap with max. 0.1 mm strainer mesh.
■ shut-off valves 10 and connection ports 12 for maintenance and venting,
■ safety relief valve 17 to prevent build-up of excessive pressure.
Blow-off pressure and capacity are governed by the user's installation design. The techni‐
cal specification of the heat exchanger must be taken into consideration.
2. Connect the supply lines and fittings.
3. Open the shut-off valve 10 at the inlet A .
4. Slowly open the shut-off valve 10 at the inlet B to gradually fill the heat exchanger with the
heat transfer medium.
5. Bleed the lines.

7 Initial Start-up
7.1 Ensuring safety
7 Initial Start-up
7.1 Ensuring safety
Here you will find instructions for a safe commissioning of the machine.

➤ Commissioning tasks may only be carried out by authorized personnel!
pressure.
in serious injury.


7 Initial Start-up
7.2 Instructions to be observed before commissioning or re-commissioning
7.2 Instructions to be observed before commissioning or re-commis‐

sioning
Incorrect or improper commissioning can cause injury to persons and damage to the machine.
➤ Commissioning may only be carried out by authorized installation and service personnel who
have been trained on this machine.
Special measures for re-commissioning after storage
Storage period Remedy

longer than:
3 months ➤ Manually fill the airend with cooling oil.
12 months ➤ Change the oil filter.
➤ Change the oil separator cartridge.
➤ Change the cooling oil.
➤ Have the motor bearings checked by an authorized KAESER service repre‐
sentative.
36 months ➤ Have the overall technical condition checked by an authorized KAESER ser‐
vice representative.
Tab. 35 Re-commissioning after storage
7.3 Checking installation and operating conditions

➤ Check and confirm all the items in the checklist before initially starting the machine.
To be checked See Confirmed?

chapter
➤ Are the operators fully familiar with safety regulations? –
➤ Have all the positioning conditions been fulfilled? 5
➤ Is a user's lockable power supply disconnecting device installed? 6.4
➤ Does the power supply conform to the specifications on the name‐ 2.1
plate?
➤ Are the power supply cable conductor cross-sections and fuse rat‐ 2.14
ings adequate?
➤ Drive motor overload protection relay set according to the power 7.4
supply voltage?
➤ Fan motor overload protection relay set according to the power sup‐ 7.5
ply voltage?
➤ Have all electrical connections been checked for tightness? –
➤ Check repeated after the first 50 operating hours?
➤ Is a shut-off valve fitted to compressed air outlet? 6.3
➤ Has the connection to the air system been made with a hose or axial 6.3
compensator?
➤ Sufficient cooling oil in the separator tank? 10.12
(oil level indicator outside the red zone)

7 Initial Start-up
7.4 Setting the overload protection relay
To be checked See Confirmed?

chapter
➤ Is there sufficient cooling oil in the airend? 7.6
➤ Is the machine firmly anchored to the floor? 6.5.1
(option H1)
➤ Are all access doors closed and latched and all removable panels in –
place and secured?
Tab. 36 Installation and operating conditions checklist
7.4 Setting the overload protection relay

Electrical diagram 13.4 gives the location of the overload protection relay.
With star-delta starting, the phase current is fed via the overload protection relay. This phase cur‐
rent is 0.58-times the rated motor current.
To prevent the overload protection relay from being triggered by voltage fluctuations, temperature
influences or component tolerances, the setting can be higher than the arithmetical phase current.
➤ Check the overload protection relay setting.
The overload protection relay shuts the machine down despite being correctly set?
➤ Contact an authorized KAESER service representative.
7.5 Setting the motor overload protection relay

Electrical diagram in chapter 13.4 gives the setting values for the motor overload protection switch.
In direct on-line starting, the current for the fan motor is fed via the motor overload protection relay.
To prevent the motor overload protection relay from being triggered by voltage fluctuations,
temperature influences or component tolerances, the setting can be higher than the rated
motor current.
➤ Check the motor overload protection relay setting.
The overload protection relay shuts the machine down despite being correctly set?
➤ Contact an authorized KAESER service representative.
7.6 Filling cooling oil into the airend

Before starting the compressor for the very first time and before re-starting after a shutdown period
of more than 3 months it is necessary to manually add a quantity of cooling oil into the airend. In
order to avoid that the cooling oil exceeds the permissible level, drain the required quantity from
the de-pressurized oil separator tank.
Chapter 10.15 provides detailed information on how to drain cooling oil from the oil separator tank.
Material 1.1 quart cooling oil from separator tank
Precondition The supply disconnecting device is switched off,

the absence of voltage has been verified.
The machine is fully vented, the pressure gauge on the oil separator tank reads 0 psigr.

7 Initial Start-up
7.7 Activating and deactivating the MODULATING control
Fig. 17 Inlet valve filling port

1 Screw plug
2 Inlet valve
1. Unscrew the filler plug from the inlet valve.

2. Pour the stipulated amount of cooling oil into the airend and replace the filler plug.
Fig. 18 Coupling
1 Airend 3 Safety screen
2 Coupling 4 Arrow showing direction of rotation
1. Remove the safety screen 3 .

2. Turn the airend 4 by turning the coupling 1 by hand in the direction indicated by the arrow 2 .
3. Replace the safety screen 3 .
7.7 Option C1
Activating and deactivating the MODULATING control
Use a shut-off valve to activate and deactivate the MODULATING control. If the MODULATING
control is deactivated, the machine always delivers the maximum possible compressed air quantity
in LOAD mode.
MODULATING control Shut-off valve

switch on open.
switch off close
Tab. 37 MODULATING control: Setting the shut-off valve


7 Initial Start-up
7.8 Starting the machine for the first time
Fig. 19 MODULATING control: Setting the shut-off valve

1 Control valve (proportional control)
2 Shut-off valve
➤ Open or close the control valve, depending on the required control mode.
The control valve is factory set. The setting should not be changed without consultation with
an authorized KAESER Service representative.
7.8 Starting the machine for the first time

Precondition No personnel are working on the machine.
All access doors are closed.
All removable panels are in place and secured.
1. Open the shut-off valve to the air network.

2. Switch on the power supply isolating device.
After the controller has carried out a self-test, the green Control voltage LED is lit continuously.
3. If required:
Change the display language as described in chapter 7.10.
4. Press the «ON »key.
The drive motor runs up and after a short time the machine switches to LOAD and delivers
compressed air.
➤ Watch for any faults occurring in the first hour of operation.
➤ After the first 50 operating hours, check all electrical connections and tighten where nec‐
essary.
Does the machine stop when the compressor motor rotates in the wrong direction?
➤ Switch off and lock out the power supply isolating device and verify the absence of volt‐
age.
➤ Changeover phase lines L1 and L2.
7.9 Setting the set point pressure

The system pressure pA is factory set to the highest possible value.

7 Initial Start-up
7.10 Setting the display language
Adjustment is necessary for individual operating conditions.

Do not set the set point pressure of the machine higher than the maximum working pressure
of the compressed air system.
The machine may not toggle more than twice per minute between LOAD and IDLE.
To reduce the cycling (toggling) frequency:
➤ Increase the difference between cut-in and cut-out pressure.
➤ Add a larger air receiver downstream to increase buffer capacity.
➤ Set the set point pressure as described in the SIGMA CONTROL 2 operating manual.
7.10 Setting the display language

The controller can display text messages in several languages.
You can set the language for texts on the display. This setting will be retained even when the ma‐
chine is switched off.
1. In operating mode, switch to the main menu with the «Return» key.
2. Press the «UP» or «DOWN» keys until the current language is shown as active line (inverse):
88 psig 176 °F
–––––––– Deutsch –––––––– Current language (active line)
▶1 xxxxxxxxxx Submenu
3. Use the «Return» key to switch to setting mode.

The language display flashes.
4. Move to the required language with «UP »or «DOWN».
5. Confirm the setting with the «Enter» key.
Result The display texts are now in the selected language.
Further information Detailed information can be found in the SIGMA CONTROL 2 operating manual.

8 Operation
8.1 Switching on and off
8 Operation
8.1 Switching on and off
Always switch the machine on with the «ON» key and off with the «OFF» key.
A power supply disconnecting device has been installed by the user.
Fig. 20 Switching on and off

1 Machine ON LED (green) 11 «LOAD/IDLE» toggle key
2 «ON» key 19 LOAD LED
3 «OFF» key 20 IDLE LED
8 Control voltage LED (green)
8.1.1 Switching on
Precondition No personnel are working on the machine.
All access doors and panels are closed and secure.
1. Switch on the power supply isolating device.

After the controller has carried out a self-test, the green Control voltage LED is lit continuously.
2. Press the «ON »key.
The green Machine ON LED is lit continuously.
If a power failure occurs, the machine is not prevented from re-starting automatically when
power is resumed.
It can re-start automatically as soon as power is restored.
Result The compressor motor starts as soon as system pressure is lower than the set point pressure (cut-
off pressure).
8.1.2 Switching off

1. Press the «LOAD/IDLE »key.
The machine switches to IDLE and the IDLE LED flashes.
2. After allowing the machine to IDLE for 20 seconds, Press the «OFF» key.
The Machine ON LED extinguishes.

8 Operation
8.2 Switching off in an emergency and switching on again
3. Press the «LOAD/IDLE »key.

The warning LED extinguishes.
The machine is ready for further operation. The machine can be re-started.
4. Switch off and lock out the power supply disconnecting device.
Result The Control voltage LED extinguishes. The machine is switched off and disconnected from the
power supply.
8.2 Switching off in an emergency and switching on again

The EMERGENCY STOP push-button is located below the control panel.
Fig. 21 Switching off in an emergency

9 EMERGENCY STOP control device:
Switching off
➤ Press the EMERGENCY STOP control device.
Result The EMERGENCY STOP button remains latched after actuation.

The compressor's pressure system is vented and the machine is prevented from automatically re-
starting.
Switching on
Precondition The fault has been rectified
1. Turn the EMERGENCY STOP device in the direction of the arrow to unlatch it.
2. Acknowledge any existing alarm messages.
Result The machine can now be started again.
8.3 Switching on and off from a remote control center

Precondition A link to the remote control center exists.

8 Operation
8.4 Switching on and off with the clock
Fig. 22 Switching on and off from a remote control center

1 «Remote control» key
2 Remote control LED
1. Attach an easily seen notice to the machine that warns of remote operation.
Remote control: danger of unexpected starting!

➤ Make sure the power supply disconnecting device is switched off before commencing any
work on the machine.
Tab. 38 Machine identification
2. Label the starting device in the remote control center as follows:
Remote control: danger of unexpected starting!

➤ Before starting, make sure that no one is working on the machine and that it can be safely
started.
Tab. 39 Remote control identification
3. Press the «remote control» key.

The remote control LED lights. The machine can be remotely controlled.
8.4 Switching on and off with the clock

Precondition The clock is programmed.

8 Operation
8.5 Interpreting operation messages
Fig. 23 Switching on and off with the clock

1 «Clock» key
2 Clock LED
1. Attach an easily seen notice warning of time-controlled operation:
Clock control: danger of unexpected starting!

➤ Make sure the power supply disconnecting device is switched off before commencing any
work on the machine.
Tab. 40 Machine identification
2. Press the «clock» key.

The clock LED lights. The machine is switched on and off by the clock.
8.5 Interpreting operation messages

The controller will automatically display operation messages informing you about the current opera‐
tional state of the machine.
Operating messages are identified with the letter O.
Further information Detailed information can be found in the SIGMA CONTROL 2 operating manual.
8.6 Acknowledging alarm and warning messages

Messages are displayed on the "new value" principle:
■ Message coming: LED flashes
■ Message acknowledged: LED illuminates
■ Message going: LED off
or
■ Message coming: LED flashes

8 Operation
■ Message going: LED flashes

■ Message acknowledged: LED off
Fig. 24 Acknowledging messages

10 LED Warning (yellow)
11 LED Alarm (red)
12 Key«Acknowledge»
Alarm message
An alarm shuts the machine down automatically. The red alarm LED flashes.
The system displays the appropriate message.
Precondition The fault has been rectified
➤ Acknowledge the message with the «acknowledge» key.

Alarm LED extinguishes.
The machine is again ready for operation.
If the machine was switched off with the EMERGENCY Stop button:
➤ Unlatch the EMERGENCY STOP button (turn in direction of the arrow) before acknowl‐
edging the alarm message.
Further information A list of possible alarm messages occurring during operation can be found in the service manual
SIGMA CONTROL 2.
Warning message
If maintenance work is to be carried out or if the warning is displayed before an alarm, the yel‐
low warning LED flashes.
The system displays the appropriate message.
Precondition The danger of an alarm is passed,

maintenance has been carried out.

8 Operation
➤ Acknowledge the message with the «Acknowledge» key.

The warning LED extinguishes.
Further information A list of possible alarm messages occurring during operation can be found in the service manual
SIGMA CONTROL 2.


There are 3 types of fault:
■ Warning:
─ Warning messages W
■ Fault (with indication):
─ Alarm messages A
─ System messages Y
─ Diagnostic messages D
■ Other faults (without indication): See chapter 9.2
The messages valid for your machine are dependent on how the individual machine is equipped.
1. Do not attempt fault rectification measures other than those given in this manual!
2. In all other cases:
Have the fault rectified by an authorized KAESER service representative.
Further information Detailed information for the various messages can be found in the service manual
SIGMA CONTROL 2.
9.2 Other Faults

Fault Possible cause Remedy
Machine runs but produces no Inlet valve not opening or only Call authorized KAESER Ser‐
compressed air. opening partially. vice representative.
Venting valve not closing. Call authorized KAESER Ser‐
Leaks in the pressure system. Check pipework and connec‐
tions for leaks and tighten any
loose fittings.
Air consumption is greater than Check the air system for leaks.
the capacity of the compressor. Shut down the consumer(s).
Hose coupling or maintenance Remove coupling or mainte‐

hose still plugged into the nance hose.
quick-release coupling on the
oil separator tank.
Cooling oil runs out of the air fil‐ Oil level in the oil separator Drain off oil until the correct lev‐
ter. tank too high. el is reached.
Inlet valve defective. Call authorized KAESER Ser‐

9.2 Other Faults
Fault Possible cause Remedy

Compressor switches between Air receiver too small. Increase size of air receiver.
LOAD and IDLE more than Airflow into the compressed air Increase air pipe diameters.
twice per minute. network restricted. Check filter elements.
The differential between cut-in Check switching differential.
and cut-out pressure too is
small.
Cooling oil leaking into the floor Hose coupling or maintenance Remove coupling or mainte‐
pan. hose still plugged into the nance hose.
quick-release coupling on the
oil separator tank.
Oil cooler leaking. Call authorized KAESER Ser‐
Leaking joints. Tighten joints.
Replace seals.
Cooling oil consumption too Unsuitable oil is being used. Use SIGMA FLUID cooling oil.
high. Oil separator cartridge split. Change the oil separator car‐
tridge.
Oil level in the oil separator Drain off oil until the correct lev‐
tank too high. el is reached.
Oil return line clogged. Check dirt trap in the return
line.
Tab. 41 Other faults and actions

10 Maintenance
10.1 Ensuring safety
10 Maintenance
10.1 Ensuring safety
Follow the instructions below for safe installation.

➤ Allow maintenance work to be performed by authorized personnel only.
pressure.
in serious injury.


10 Maintenance
10.2 Following the maintenance plan

10.2.1 Logging maintenance work
The maintenance intervals given are those recommended for KAESER original components
with average operating conditions.
➤ In adverse conditions, perform maintenance work at shorter intervals.
Adverse conditions are, e.g.:

■ high temperatures
■ much dust
■ high number of load changes
■ low load
➤ Adjust the maintenance intervals with regard to local installation and operating condi‐
tions.
➤ Document all maintenance and service work.
This enables the frequency of individual maintenance tasks and deviations from our recom‐
mendations to be determined.
Further information A prepared list is provided in chapter 10.18.
10.2.2 Resetting maintenance interval counters

According to the way a machine is equipped, sensors and/or maintenance interval counters moni‐
tor the operational state of important functional devices. Required maintenance work is shown on
SIGMA CONTROL 2 .
Precondition Maintenance performed and

maintenance message acknowledged.
➤ Reset the maintenance interval counter as described in the SIGMA CONTROL 2 operating
manual.
10.2.3 Regular maintenance tasks

The table below lists maintenance tasks required.
➤ Take note of the controller's service messages and carry out tasks punctually, taking ambient
and operating conditions into account.
Interval Maintenance task See chapter

Weekly Check the cooling oil level. 10.12
Control cabinet: 10.3
Check the filter mat
Up to 1,000 h Clean the radiator. 10.4
Check the cooling air filter mat 10.5
Up to 3,000 h Change the cooling air filter mat 10.5
Control cabinet: 10.3
Change the filter mat.
h = operating hours

10 Maintenance
Interval Maintenance task See chapter

Display: Change the air filter element. 10.7
SIGMA CONTROL 2 Check the coupling. 10.9
Display: Change the oil filter. 10.16
SIGMA CONTROL 2
At least annually
Display: Change the oil separator cartridge. 10.17
SIGMA CONTROL 2
At the latest every
3 years
Variable, see table 43 Change the cooling oil. 10.15
Annually Check the safety relief valve. 10.10
Check the overheating safety shutdown function. 10.11
Check the cooler for leaks. 10.4
Maintain the heat recovery system. 10.6
Check that all electrical connections are tight. –
h = operating hours
Tab. 42 Regular maintenance tasks
10.2.4 Cooling oil changing interval

Machine utilization and ambient conditions are important criteria for the number and length of the
change intervals.
An authorized KAESER service representative will support you in determining appropriate in‐
tervals and provide information on the possibilities of oil analysis.
➤ Please observe national regulations regarding the use of cooling oil in oil-injected screw com‐
pressors.
➤ Check operating conditions and adjust intervals as necessary.
KAESER LUBRICANTS
SIGMA Lubricant Description Maximum Recommended Change Interval
First oil change Subsequent oil change
M–460 ISO 46 Semi-Synthetic 2,000 Hours 3,000 Hours
Lubricant
S–460 ISO 46 Synthetic Lu‐ 6,000 Hours 8,000 Hours
bricant
S–680 ISO 68 Synthetic Lu‐ 6,000 Hours 8,000 Hours
bricant
FG–460 ISO 46 Food Grade 2,000 Hours 3,000 Hours
Synthetic Fluid
Tab. 43 Oil change intervals lubricants

10 Maintenance
10.3 Control cabinet: Clean or renew the filter mat
10.2.5 Regular service tasks

The table below lists necessary service tasks.
➤ Only an authorized KAESER service representative should carry out service work.
➤ Have service tasks carried out punctually taking ambient and operating conditions into ac‐
count.
Interval Service task

Display: Have the valves checked.
SIGMA CONTROL 2 Compressor drive motor
Have motor bearings checked.
Display: Fan motor:
SIGMA CONTROL 2 Have motor bearings checked.
At the latest every
3 years
Up to 36,000 h Have hose lines replaced.
At the latest every ■ Pressure pipes
6 years ■ Control air lines
■ Intake line at intake valve
h = operating hours
Tab. 44 Regular service tasks
10.3 Control cabinet: Clean or renew the filter mat

A filter mat is placed behind every ventilation grill. Filter mats protect the control cabinet from in‐
gress of dirt. If the filter mats are clogged, adequate cooling of the components is no longer ensur‐
ed. In such a case, clean or replace the filter mats.
Material Warm water and household detergent

Spare parts (as required)
Precondition The power supply isolating device is switched off,

The machine has cooled down.

10 Maintenance
10.4 Cooler maintenance
Fig. 25 Switching cabinet ventilation

1 Ventilation grill
2 Filter mat
1. Carefully remove the ventilation grill and take out the filter mat.
2. Beat the mat or use a vacuum cleaner to remove loose dirt. If necessary, wash with lukewarm
water and household detergent.
3. Change the filter mat if cleaning is not possible or if the change interval has expired.
4. Insert the filter mat in the frame and latch in the ventilation grill.
10.4 Option K1
Cooler maintenance
Regularly clean the cooler. This ensures reliable cooling of the machine and the compressed air.
The frequency is mainly dependent on local operating conditions.
A leaking cooler results in loss of cooling oil and compressed air.
Clogged coolers are indicative of unfavorable ambient conditions. Such ambient conditions
clog the cooling air ducts in the machine's interior and the engines resulting in increased
wear and tear.
➤ Have the authorized KAESER service representative clean the cooling air ducts.
Material Brush and vacuum cleaner

Face mask (as required)


10 Maintenance
10.5 Cleaning or Renewing the Cooling Air Filter Mat
Fig. 26 Clean cooler/radiator

1 Radiator
2 Brush
Clean cooler/radiator
Do not use sharp objects to clean the cooler. It could be damaged.

Avoid creating clouds of dust.
➤ Dry brush the oil and air coolers and use a vacuum cleaner to suck up the dirt.
The air and oil coolers can no longer be properly cleaned?
➤ Have severe clogging removed by an authorized KAESER service representative.
Check the cooler for leaks
➤ Visual inspection: Did cooling oil escape?

Is a cooler leaking?
➤ Have the defective cooler repaired immediately by an authorized KAESER service repre‐
sentative.
10.5 Option K3
Cleaning or Renewing the Cooling Air Filter Mat
The filter mat helps to keep the cooler clean. If the filter mat is clogged, adequate cooling of the
components is no longer ensured.
Material Warm water and household detergent

Spare parts (as required)
Precondition The machine is switched off.

10 Maintenance
10.6 Maintaining the heat recovery system
Fig. 27 Cooling air filter mat

1 Cooling air filter mat
2 Retaining frame
3 Fixing
Removal
1. Open the fixing 3

by turning 90° counter clockwise with a screwdriver.
2. Remove the frame 2 .
Cleaning
➤ Renew the mat if cleaning is not possible or has already been carried out 5 times.
➤ Beat the mat 1 or use a vacuum cleaner to remove loose dirt.

If necessary, wash the mat in lukewarm water (about 100 °F) and household detergent then
rinse thoroughly.
Refitting
➤ Replace the frame and close the fixings.

Use a screwdriver to turn the fixings 90° clockwise until they latch.
10.6 Option W1/W2/W3

Maintaining the heat recovery system
Deposits in the heat exchanger can significantly reduce its capacity to transfer heat.
Check the heat exchanger regularly for leaks and contamination. Frequency of checking is depend‐
ant on the characteristics of the heat transfer medium.
➤ Have the external heat recovery system checked annually by an authorized KAESER service
representative.

10 Maintenance
10.7 Changing the air filter
10.6.1 Option W1
External heat recovery system
➤ Have the external heat recovery system checked annually by an authorized KAESER service
representative.
10.6.2 Option W2/W3

Internal heat recovery
Pressure in the cooling oil circuit is generally higher than that in the heat recovery system. If a leak
occurs, oil will run into the heat-receiving medium. Increased cooling oil loss can indicate a leaking
heat exchanger.

a check has been made that no voltage is present.
1. Check the heat exchanger visually for leaks.

2. Have an authorized KAESER service representative check the heat exchanger for internal
leaks and clean if contaminated.
10.7 Changing the air filter

Check that all sealing surfaces match each other. The use of an unsuitable air filter element
can permit dirt to ingress into the pressure system and cause damage to the machine.
Do not clean the air filter element. A damaged air filter element can permit dirt to ingress the
pressure system and cause damage to the machine.
Material Spares


10 Maintenance
10.8 Motor maintenance
Fig. 28 Air filter maintenance

1 Clamping nut 4 Air filter cartridge
2 Clamping nut 5 Cover
3 Back plate
1. Undo the nuts 1 fixing the cover 5 to the side panel and take out the complete filter.
2. Unscrew the nut 2 and remove the back plate 3 .
3. Clean all parts and sealing surfaces.
4. Insert the element 4 in the cover 5 and lay on the back plate 3 .
5. Use the screw and nut 2 to hold the housing together.
6. Insert the air filter housing in the side panel and secure by the cover 5 with the nuts 1 .
7. Close all access doors and replace all enclosure panels.
8. Switch on the power supply isolating device and reset the maintenance interval counter.
10.8 Motor maintenance

The drive motor bearings are permanently greased. Re-greasing is not necessary.
Compressor motor
➤ Have the motor bearings checked by an authorized KAESER service representative.
Fan motor
➤ Have the motor bearings checked by an authorized KAESER service representative.
10.9 Checking the Coupling

A defective coupling is recognizable by:
■ noisy running,
■ surface cracks,
■ color change.

10 Maintenance
10.10 Testing the safety relief valve
Danger of injury from rotating coupling!

➤ Never switch the machine on without the safety screen in place over the coupling.
Fig. 29 Checking the coupling

1 Safety screen
2 Coupling
Check for uneven or noisy running
Precondition The machine is running
➤ Check the coupling for noisy or uneven running
Make a visual check for damage
Precondition The power supply disconnecting device is switched off.

The disconnecting device is locked in the off position.
A check has been made that no voltage is present.
1. Remove the securing screws and take off the safety screen.
2. Turn the coupling my hand and look for damage or color change.
3. Refit the safety screen.
4. Close all access doors and replace all enclosure panels.
Does the coupling have cracks or changes in color?
➤ Have a damaged coupling changed by an authorized KAESER service representative.
10.10 Testing the safety relief valve

In order to check the safety relief valve, the machine's working pressure is raised above the acti‐
vating pressure of the valve.

10 Maintenance
10.11 Checking the overheating safety shutdown function
Blow off protection and air system pressure monitoring are switched off during the test. In normal
operation, the blow-off protection will switch off the machine before the safety relief valve responds.
During the inspection, the blow-off protection will switch off the machine only when the activating
pressure of the safety relief valve has been exceeded by 14.7 psig.
➤ Follow the detailed description of this procedure in the SIGMA CONTROL 2 operating
manual
➤ Never operate the machine without a correctly functioning safety relief valve.
➤ Have a defective safety relief valve replaced immediately.
Excessive noise is caused when the safety relief valve blows off!
➤ Close all access doors, replace and secure all removable panels.
➤ Wear hearing protection.
Precondition The machine is switched off.
1. Close the user's shut-off valve between the machine and the air distribution network.
2. Read off the activating pressure on the valve.
(the activating pressure is usually to be found at the end of the part identification)
3. Log on to SIGMA CONTROL 2 with access level 2.
4. Observe the display of pressure on SIGMA CONTROL 2 and call up the test function.
5. Risk of burns due to released cooling oil and compressed air when blowing off
the safety relief valve!
➤ Close all access doors, replace and secure all removable panels.
➤ Wear eye protection.
6. End the test as soon as the safety relief valve blows off or working pressure exceeds the acti‐
vating pressure of the safety relief valve by nearly 14.7 psig.
7. If necessary, vent the machine and replace the defective safety relief valve.
8. Deactivate the test function
9. Open the user's shut-off valve between the machine and the air distribution network.
10.11 Checking the overheating safety shutdown function

The machine should shut down if the airend discharge temperature reaches a maximum of 230 °F.
➤ Check the safety shutdown function as described in the SIGMA CONTROL 2 operating man‐
ual.
The machine does not shut down?
➤ Have the safety shutdown function checked by an authorized KAESER distributor.
10.12 Checking the cooling oil level

In frequency-controlled compressors (SFC) the oil level indicator is only accurate when the
machine is running at or near maximum speed.
The lower the pressure at the compressed air outlet, the higher the speed.
SIGMA CONTROL 2 displays this value.

10 Maintenance
10.13 Venting the machine (de-pressurizing)
Precondition The machine has been running at least 5 minutes under LOAD.
Fig. 30 Checking the cooling oil level

1 Minimum oil level
2 Maximum oil level
3 Optimum oil level
1. Danger of burning - hot surfaces!

➤ Wear long-sleeved clothing and protective gloves.
2. Check the oil level with machine running under LOAD.
Result As soon as the minimum level is reached: Replenish the cooling oil.

Venting takes place in three stages:
■ Isolate the compressor from the air system.
■ Vent the oil separator tank.
■ Manually vent the air cooler.
The machine must be isolated from the compressed air network and completely vented be‐
fore undertaking any work on the pressure system.
Material The maintenance hose with hose coupling and shut-off valve needed for venting is stowed beneath
the oil separator tank.

Escaping oil mist is damaging to health.

➤ Do not direct the maintenance hose at persons while venting.
➤ Do not inhale the oil mist.

10 Maintenance
Fig. 31 Venting the machine

1 Hose coupling (air cooler venting) 7 Shut-off valve
2 Pressure gauge A Shut-off valve open
3 Hose coupling (oil separator tank venting) B Shut-off valve closed
6 Plug-in nozzle 8 Maintenance hose
Isolating the machine from the air system
➤ Close the user's shut-off valve between the machine and the air distribution network.
If no shut-off valve is provided by the user, the complete air network must be vented.
Venting the oil separator tank
The oil circulation vents automatically as soon as the machine is stopped.

➤ Check that the oil separator tank pressure gauge reads 0 psig.
The pressure gauge does not read 0 psig after automatic venting?
➤ Make sure that the shut-off valve is closed or that the complete air system is vented.
➤ With the shut-off valve closed, insert the male hose fitting 6 into the hose coupling 3 .
➤ Slowly open the shut-off valve 7 to release pressure.
➤ Disconnect the male hose fitting 6 and close the shut-off valve 7 .
➤ If manual venting does not bring the oil separator tank pressure gauge to zero: Contact
an authorized KAESER service representative.
Manually venting the air cooler
After shutting down the compressor and venting the oil separator tank, the machine is still un‐
der pressure from the air system or the section from the shut-off valve to the minimum pres‐
sure/check valve.
1. With the shut-off valve closed, insert the male hose fitting 6 into the hose coupling 1 .
2. Slowly open the shut-off valve 7 to release pressure.
3. Disconnect the male hose fitting 6 and close the shut-off valve 7 .

10 Maintenance
10.14 Replenishing the cooling oil

Material The maintenance hose with hose coupling and shut-off valve needed for venting is stowed beneath
the oil separator tank.

Fig. 32 Replenishing the cooling oil

1 Hose coupling (air cooler venting) 6 Plug-in nozzle
2 Pressure gauge 7 Shut-off valve
3 Hose coupling (oil separator tank venting) A Shut-off valve open
4 Oil filler port with plug B Shut-off valve closed
5 Cooling oil level indicator 8 Maintenance hose
1. Vent the machine as described in section 10.14.1.

2. Fill with cooling oil and test run as described in section 10.14.2.
10.14.1 Venting the machine (de-pressurizing)

Venting takes place in three stages:
■ Isolate the compressor from the air system.
■ Vent the oil separator tank.
■ Manually vent the air cooler.
Escaping oil mist is damaging to health.

➤ Do not direct the maintenance hose at persons while venting.
➤ Do not inhale the oil mist.

10 Maintenance
Isolating the machine from the air system
➤ Close the user's shut-off valve between the machine and the air distribution network.
If no shut-off valve is provided by the user, the complete air network must be vented.
Venting the oil separator tank
The oil circulation vents automatically as soon as the machine is stopped.

➤ Check that the oil separator tank pressure gauge reads 0 psig.
The pressure gauge does not read 0 psig after automatic venting?
➤ Make sure that the shut-off valve is closed or that the complete air system is vented.
➤ With the shut-off valve closed, insert the male hose fitting 6 into the hose coupling 3 .
➤ Slowly open the shut-off valve 7 to release pressure.
➤ Disconnect the male hose fitting 6 and close the shut-off valve 7 .
➤ If manual venting does not bring the oil separator tank pressure gauge to zero: Contact
an authorized KAESER service representative.
Manually venting the air cooler
After shutting down the compressor and venting the oil separator tank, the machine is still un‐
der pressure from the air system or the section from the shut-off valve to the minimum pres‐
sure/check valve.
2. Slowly open the shut-off valve 7 to release pressure.
3. Disconnect the male hose fitting 6 and close the shut-off valve 7 .
10.14.2 Topping up with cooling oil and trial run

Replenishing the cooling oil
A sticker on the oil separator tank specifies the type of oil used.
1. Compressed air!
Compressed air and devices under pressure can injure or cause death if the contained energy
is released suddenly.
2. The machine could be damaged by unsuitable oil!
➤ Never mix different types of oil.
➤ Never top up with a different type of oil to that already used in the machine.
3. Slowly unscrew the filler plug 4 .
4. Top up to bring the oil to the correct level.
5. Renew the filler plug's gasket if necessary and screw the plug into the filler port.
Starting the machine and carrying out a trial run
1. Close all access doors, replace and secure all removable panels.

10 Maintenance
10.15 Changing the cooling oil
3. After approx. 10 minutes of operation: Check the cooling oil level and top up if necessary.
4. Switch off the machine and check visually for leaks.

Drain the oil completely from the following components:
■ Oil separator tank
■ Oil cooler
■ Airend
■ Internal heat recovery system (Option W1/W2/W3)
➤ Always change the oil filter and oil separator cartridge when changing the oil.
➤ Contact an authorized KAESER service representative if condensate is detected in the
cooling oil. It is necessary to adjust the airend discharge temperature to suit operating
conditions.
Compressed air helps to expel the oil. This compressed air can be taken either from the compres‐
sor itself or from an external source.
An external source of compressed air is necessary in the following cases:

■ The machine is not operational.
■ The machine is to be restarted after a long period of standstill.
Material Cooling oil

Cooling oil receptacle
The maintenance hose with hose coupling and shut-off valve is stowed beneath the oil separator
tank.
There is risk of burns from hot components and oil!

➤ Wear long-sleeved clothing and gloves.

10 Maintenance
Fig. 33 Changing the cooling oil, oil separator tank

1 Hose coupling (air cooler venting) A Shut-off valve open
2 Pressure gauge B Shut-off valve closed
3 Hose coupling (oil separator tank venting) 8 Maintenance hose
4 Oil filler port with plug 9 Hose coupling (oil drain)
5 Cooling oil level indicator 10 Shut-off valve (venting line)
6 Plug-in nozzle 11 Shut-off valve (oil drain)
7 Shut-off valve
Oil changing with help from internal pressure Changing the oil using an external compressed
air source
Machine has been running at least 5 minutes The supply disconnecting device is switched off,
under LOAD. the device is locked off,
The machine is fully vented, the pressure gauge the absence of voltage has been verified.
on the oil separator tank reads 0 psig. The machine is fully vented, the pressure gauge
1. Close the shut-off valve 10 in the venting on the oil separator tank reads 0 psig.
line. An external source of compressed air is availa‐
2. Select IDLE running. ble.
3. Start the machine and watch the oil separa‐ 1. Close the shut-off valve 10 in the venting
tor tank pressure gauge 2 until it reads 43– line.
72 psig. 2. With the shut-off valve closed, insert the
4. Switch off and lock out the power supply male hose fitting 6 into the hose cou‐
disconnecting device and check that no volt‐ pling 3 .
age is present. 3. Connect the maintenance hose to the exter‐
5. Wait at least 2 minutes to allow the oil to nal air supply.
flow back to the separator tank. 4. Open the shut-off valve 7 until the pressure
gauge on the oil separator tank reads 3–
5 bar.
5. Close the shut-off valve 7 and remove the
male hose fitting from the coupling.
Draining the oil from the separator tank
1. Have an oil receptacle ready.

3. Place the other end of the maintenance hose in the oil receptacle and secure it in place.

10 Maintenance
4. Open the shut-off valve 11 .

5. Slowly open the shut off valve 7 in the maintenance hose to release oil and close immediately
when air escapes.
6. Close the shut-off valve 11 and unplug the male hose fitting.
Draining the oil from the cooler
Fig. 34 Changing the cooling oil, oil cooler

1 Oil cooler 6 Plug-in nozzle
2 Hose coupling (oil drainage) 7 Shut-off valve
3 Shut-off valve

4. Open the shut-off valve 3 .
5. Slowly open the shut-off valve 7 and allow cooling oil and air to escape completely until the
pressure gauge reads 0 psig.

10 Maintenance
Draining the oil from the airend
Fig. 35 Changing the cooling oil, airend

1 Compressed air outlet on airend 4 Safety screen
2 Hose coupling (oil drainage) 5 Coupling
3 Shut-off valve

4. Open shut-off valves 3 and 7 (Fig. 33)
5. Remove the coupling safety screen 4 and turn the coupling 5 by hand at least five revolutions
until all the oil has run out.
6. Fit the safety screen again.
Result The cooling oil is drained from the airend.

Turning the coupling lets a small quantity of cooling oil return to the oil separator container.
Thus, please repeat the step "Draining cooling oil from the oil separator container", in order to also
drain this cooling oil.
Option W1 Draining the oil from the external heat recovery system
If the machine is connected to an external heat recovery system, drain the oil from the heat ex‐
changer at a suitable point.

The machine is fully vented, the pressure gauge on the oil separator tank reads 0 psig.

2. Open the external heat recovery system and allow the oil to drain completely.
3. Close the external heat recovery system.
Option W2/W3 Draining cooling oil from the internal heat exchanger
A shut-off valve is provided for draining the oil from the heat exchanger.

10 Maintenance
10.16 Changing the oil filter
Fig. 36 Changing the cooling oil, heat recovery system

1 Hose coupling
2 Thermostatic valve
3 Shut-off valve

2. Insert the male hose fitting 6 (Fig. 33) in the hose coupling 2 .
4. Open the shut-off valves 3 and 7 (Fig. 33) and allow the oil to drain completely.
Filling with cooling oil
1. Open the filler plug 4 (Fig. 33) slowly.

2. Fill with cooling oil.
3. Check the filler plug and ring seal for damage and screw the plug back in again.
3. Switch on the power supply and reset the maintenance interval counter.
4. Start the machine and check the oil level again after about 10 minutes, topping up if necessary.
➤ Dispose of used oil in accordance with environmental protection regulations.


10 Maintenance
Material Spares
Cooling oil receptacle

The machine is fully vented,
the pressure gauge on the oil separator tank reads 0 psig.
There is risk of burns from hot components and oil!

➤ Wear long-sleeved clothing and gloves.
Fig. 37 Changing the oil filter

1 Oil filter
2 Direction to unscrew
Changing the oil filter
1. Compressed air!
2. Unscrew the oil filter anti-clockwise, catch oil spillage and dispose of in accordance with envi‐
ronmental protection regulations.
3. Lightly oil the new filter's gasket.
4. Turn the oil filter clockwise by hand to tighten.
➤ Dispose of parts and materials contaminated with oil in accordance with environmental
protection regulations.

10 Maintenance
10.17 Changing the oil separator cartridge
4. After approx. 10 minutes of operation: Check the cooling oil level and top up if necessary.

The oil separator element cannot be cleaned.
The life of the oil separator cartridge is influenced by:

■ contamination in the air drawn into the compressor,
■ and adherence to the changing intervals for:
─ Cooling oil
─ Oil filter
─ Air filter
Material Spares
Cleaning cloth

The machine is fully vented,
the pressure gauge on the oil separator tank reads 0 psig.

10 Maintenance
Fig. 38 Changing the oil separator cartridge

14 Cover 19 Self-locking nut
15 Dirt trap 20 Screw connection
16 Air pipe 21 Gasket
17 Fixing screw 23 Oil separator cartridge
Changing the oil separator cartridge
1. Compressed air!
2. Unscrew the fitting 20 and carefully put the parts to one side, then pull out the copper pipe at
item 15 .
3. Unscrew the nut 19 and turn the air pipe 16 to one side.
4. Remove the cover fixing screws 17 and carefully remove the cover 14 .
5. Take out the old oil separator cartridge 23 together with the gaskets 21 and dispose of ac‐
cording to environmental protection regulations.
6. Clean all sealing faces.
7. Insert the new oil separator cartridge with gaskets and screw down the cover.
8. Renew the O-ring and strainer in the dirt trap 15 .
9. Attach the air pipe to the cover 14 with a new, self-locking nut.
10. Replace and tighten all fittings.
➤ Dispose of parts and materials contaminated with oil in accordance with environmental
protection regulations.

10 Maintenance
4. After approx. 10 minutes of operation: Switch off the machine and check visually for leaks.

10 Maintenance
10.18 Documenting maintenance and service work
10.18 Documenting maintenance and service work

Machine number:
➤ Enter maintenance and service work carried out in the list.
Date Maintenance task carried out Operating hours Signature
Tab. 45 Logged maintenance tasks

11.1 Note the nameplate

11.1 Note the nameplate
The nameplate contains all information to identify your machine. This information is essential to us
in order to provide you with optimal service.
➤ Please give the information from the nameplate with every inquiry and order for spares.
11.2 Ordering consumable parts and operating fluids/materials

KAESER consumable parts and operating materials are original Kaeser products. They are specifi‐
cally selected for use in KAESER machines.
Unsuitable or poor quality consumable parts and operating fluids/materials may damage the ma‐
chine or impair its proper function.
Personal injury may result from machine damage.
There is risk of personal injury or damage to the machine resulting from the use of unsuita‐
ble spares or operating fluids/materials.
➤ Use only original KAESER parts and operating fluids/materials.
➤ Have an authorized KAESER Service Technician carry out regular maintenance.
Machine
Name Quantity Number

Air filter cartridge 1 1250
Filter mat (control cabinet) 3 1100
Filter mat (Option K3) 1 1050
Oil filter 1 1200
Oil separator cartridge 1 1450
Cooling oil 1 1600
Tab. 46 Consumable parts
11.3 KAESER AIR SERVICE

KAESER AIR SERVICE offers:
■ authorized KAESER service representatives with KAESER factory training,
■ increased operational reliability ensured by preventive maintenance,
■ energy savings achieved by avoidance of pressure losses,
■ optimum conditions for operation of the compressed air system,
■ the security of genuine KAESER spare parts,
■ increased legal certainty as all regulations are kept to.
➤ Why not sign a KAESER AIR SERVICE maintenance agreement!

11.4 Service Addresses
Result Your advantage:

lower costs and higher compressed air availability.
11.4 Service Addresses

Addresses of KAESER representatives are given at the end of this manual.
11.5 Spare Parts for Service and Repair

With the help of this parts list you can plan your material requirement according to operating condi‐
tions and order the spare parts you need.
➤ Make sure that any service or repair tasks not described in this manual are carried out by
an authorized KAESER Service Technician.



12.1 Putting Out of Operation

12.1 Putting Out of Operation
This is necessary under the following circumstances:
■ The machine is temporarily not needed.
■ The machine is to be moved to another location.
■ The machine is to be scrapped.
Temporarily putting out of operation
Precondition The machine can be started at regular intervals.
➤ Run the machine once a week for at least 30 minutes under LOAD to ensure sufficient protec‐
tion against corrosion.
Putting out of operation for a longer period
Precondition Before putting out of operation, the machine should be run under LOAD for at least 30 minutes.
Switch off the power supply disconnecting device,
the disconnect device is locked in the off position,
check that no voltage is present.
Machine fully vented (no pressure).
1. Allow the machine to cool down completely.

2. Disconnect all air and electrical connections.
12.2 Packing
A wooden crate is required for overland transport to protect the machine from mechanical damage.
Other measures must be taken for the transport of machines by sea or air. Please contact an au‐
thorized KAESER service representative for more information.
Material Desiccant
Plastic sheeting
Wooden crate
Precondition The machine is decommissioned.

The machine is dry and cooled down.
1. Place sufficient desiccant silica gel or desiccant clay) in the machine.

2. Wrap the machine fully in plastic sheeting.
3. Protect the machine in a wooden crate against mechanical damages.
12.3 Storage
Moisture can lead to corrosion, particularly on the surfaces of the airend and in the oil separator
tank.
Frozen moisture can damage components, valve diaphragms and gaskets.

12.4 Transport
The following measures also apply to machines not yet commissioned.

Please consult with KAESER if you have questions to the appropriate storage and commis‐
sioning.
1. Moisture and frost can damage the machine!

➤ Prevent ingress of moisture and formation of condensation.
➤ Maintain a storage temperature of >32 °F.
2. Store the machine in a dry, frost-proof room.
12.4 Transport
12.4.1 Safety
Weight and center of gravity determine the most suitable method of transportation. The center of
gravity is shown in the drawing in chapter 13.3.
➤ Please consult with KAESER if you intend to transport the machine in freezing tempera‐
tures.
Precondition Transport only using a forklift truck or lifting gear and only by personnel trained in the safe trans‐
portation of loads.
➤ Make sure the danger area is clear of personnel.
12.4.2 Transport with a forklift truck

Precondition The forks are fully under the machine.
Fig. 39 Transport with a forklift truck
➤ Drive the forks completely under the machine or pallet and lift carefully.
12.4.3 Transport with a crane

Suitable lifting gear ensures correct transportation.
The lifting slings must be fed under the machine.
The slings may not bear on the side of the machine enclosure.
Examples of unsuitable fixing points:

■ Pipe sockets
■ Flanges

12.5 Disposal
■ Attached components such as cyclone separators, condensate drains or filters

■ Rain protection covers
➤ Please consult with KAESER if you have questions to the appropriate lifting gear.
Precondition The lifting gear complies with local safety regulations.

No pressure should bear on the sides of the machine cabinet.
Fig. 40 Transport with a crane

1 Lifting gear
2 Slings
1. The machine can be damaged by incorrect attachment of the lifting gear!

➤ Do not attach the lifting gear to any of the machine components.
2. Use the lifting gear correctly and lift the machine carefully.
12.5 Disposal
When disposing of a machine, drain out all liquids and remove dirty filters.
Precondition The machine is decommissioned.
1. Completely drain the cooling oil from the machine.

2. Remove used filters and the oil separator cartridge.
3. Hand the machine over to an authorized disposal expert.
➤ Parts contaminated with cooling oil must be disposed of in accordance with local environ‐
ment protection regulations.
Compressors with refrigeration dryers
The sealed refrigerant circuit still contains both refrigerant and oil.
➤ Refrigerant and oil must be drained and disposed of by authorized personnel.

13 Annex
13.1 Pipeline and instrument flow diagram (P+I diagram)
13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex
13.2 Pipe and Instrument Flow Diagram (P+I diagram): MODULATING control mode
13.2 Option C1
Pipe and Instrument Flow Diagram (P+I diagram): MODULATING
control mode

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex
13.3 Dimensional drawing
13.3 Dimensional drawing

Die Zeichnung bleibt unser ausschließliches Eigentum. Sie wird nur zu dem vereinbarten Zweck anvertraut und darf zu keinem anderen Zweck verwendet werden. Drawings remain our exclusive property. They are entrusted only for the agreed purpose. Copies or any other reproduction, including storage, treatment and Entwicklungsbedingte Änderungen
Kopien oder sonstige Vervielfältigungen einschließlich Speicherung, Verarbeitung oder Verbreitung unter Verwendung elektronischer Systeme dürfen nur zu dem dissemination by use of electronic systems must not be made for any other than the agreed purpose. Neither originals nor reproductions may be given to or made vorbehalten. Zeichnung darf nur über CAD
vereinbarten Zweck angefertigt werden. Weder Original noch Vervielfältigungen dürfen Dritten ausgehändigt oder in sonstiger Weise zugänglich gemacht werden. available to third parties. geändert werden.
Option:
Air cooling
R 1 1/4
Air discharge
Machine mountings
21 1/2
3 1/8
Cooling air filter mat

outside threading
Air discharge
2 3/4
1 3/4
Prepared for heat recovery
Internal heat recovery ∆t=55K

Internal heat recovery ∆t=25K
View X
18 3/4
NPT 3/4
31 1/4
33 7/8
37 1/8
26 5/8
36 1/4
13 1/4 1 7/8
K1
H1
K3
W1
W2
W3
Code:
W1 W2 W3
2 3/8
ATTENTION! 25 1/8 6 1/2

5 3/4
CG : Centre of gravity
Inlet air
Inlet air
21 5/8 13 3/4
Cooling air outlet
CG
53 1/8
41 3/4
Allow 4" clearance in narrow passages

CG
position marginally dependent on design

55 5/8 K3
30 3/8
Air discharge
and doorways Crating has not been considered

11 1/8 11 5/8
Gez.
Gepr.
59 1/4 22 5/8 22 1/2 2 1/8
Maßstab
K3
Tag
Freigeg. 9.3.2012
9.3.2012
Name
Gans
8 1/8 12
Seubold
Cooling air inlet
Cooling air inlet
di a
.
3 7/8
Ersatz für
/8
ASD
Y
.
Electrical connections
Z
3 7 1/2
K1
15 3/8 8 5/8
dia 6 3/4
18 1/4
27 1/4 24 3/8 1/8
1 1/2
5 1/2
H1
X
3 5/8
3 7/8
10 3/4 1 3/8
4 3/8
Air discharge
8 5/8
1 3/8
2 1/8
2 3/4
9 1/2
10 1/2 9 1/2
ASD 57/8bar 50Hz

Y
T12029.00 use
Air
3x M25
All dimensions are in inches!

d i a.
discharge
00
Ä-Index
2 1/4
Dimensional drawing 13.3
Annex 13
Die Zeichnung bleibt unser ausschließliches Eigentum. Sie wird nur zu dem vereinbarten Zweck anvertraut und darf zu Entwicklungsbedingte Änderungen vorbehalten. Zeichnung darf nur über CAD geändert werden.
keinem anderen Zweck verwendet werden. Kopien oder sonstige Vervielfältigungen einschließlich Speicherung, Verarbeitung
oder Verbreitung unter Verwendung elektronischer Systeme dürfen nur zu dem vereinbarten Zweck angefertigt werden.
Weder Original noch Vervielfältigungen dürfen Dritten ausgehändigt oder in sonstiger Weise zugänglich gemacht werden.
AS 40
AS25/30/40S
.
Cooling air inlet
V. = AS 25 2170 cfm
V. = AS 30 2120 cfm
V. = AS 40S 2250 cfm
V = AS 40 2750 cfm
ptot.=
ptot.=
1/4 inch/wc
1/8 inch/wc
18 1/4
without filter
Total permissible pressure loss for installed ducting
.
27 1/4 24 3/8
Cooling
V = AS 40
3 5/8
air outlet
1/8 inch/wc
1/16 inch/wc
with filtermats
3120 cfm
V. = AS 25/30/40S 2600 cfm
Gez.
Gepr.
Maßstab
Tag
Freigeg. 28.06.2011
28.06.2011
22 1/2 2 1/8
Name
Dumdey
Schubart
Ersatz für
11 1/8 11 5/8
AS 31/36/47/40
Straight duct
Filter mat frame
loss for installed ducting

Total permissible pressure
T10172.01
use
All dimensions are in inches!
00
Ä-Index
Dimensional drawing 13.3
Annex 13
13 Annex
13.4 Electrical Diagram

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex

13 Annex


Asd 2C 10224114 10-000 00use

Uploaded by

Copyright:

Available Formats

Asd 2C 10224114 10-000 00use

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asd 2C 10224114 10-000 00use

Uploaded by

Copyright:

Available Formats

Service Manual

ASD SIGMA CONTROL 2

1 Regarding this Document

Service Manual Screw Compressor

4.2 Functional Description of the Machine ............................................................................. 27

Service Manual Screw Compressor

Service Manual Screw Compressor

Service Manual Screw Compressor

Fig. 1 Maximum relative humidity of inlet air ........................................................................................ 6

Service Manual Screw Compressor

Service Manual Screw Compressor

Tab. 1 Danger levels and their definition (personal injury) .................................................................... 1

Service Manual Screw Compressor

Service Manual Screw Compressor

1 Regarding this Document

1.2 Further documents

Missing documents can be requested from KAESER.

1.4 Symbols and labels

Tab. 1 Danger levels and their definition (personal injury)

Service Manual Screw Compressor

The type and source of the imminent danger is shown here!

1.4.2 Potential damage warnings

Warning notices for damages are identified by their signal term.

Tab. 2 Danger levels and their definition (damage to property)

The type and source of the imminent danger is shown here!

➤ Carefully read and fully comply with warnings against damages.

1.4.3 Other alerts and their symbols

Service Manual Screw Compressor

Further information Further subjects are introduced here.

Service Manual Screw Compressor

The nameplate is located on the outside of the machine:

➤ Enter here the nameplate data as a reference:

Option Option code Exists?

Service Manual Screw Compressor

Option Option code Exists?

ASD 25 ASD 30 ASD 40S ASD 40

Tab. 5 Machine weight

2.5 Ambient conditions

Tab. 7 Ambient conditions

Service Manual Screw Compressor

Fig. 1 Maximum relative humidity of inlet air

ASD 25 ASD 30 ASD 40S ASD 40

Tab. 8 Overview Ventilation

Maximum working pres‐ ASD 25 ASD 30 ASD 40S ASD 40

Tab. 9 Safety relief valve activating pressure

Service Manual Screw Compressor

2.9 Cooling Oil Recommendation

2.9.1 Basic Information

2.9.2 KAESER Lubricants

Service Manual Screw Compressor

Specialty KAESER LUBRICANTS:

2.10 Cooling oil charge

ASD 25 ASD 30 ASD 40S ASD 40

Tab. 11 Cooling oil charge

Option W1/W2/W3 Heat recovery

Tab. 12 Cooling oil charge (Option W1)

Service Manual Screw Compressor

Option W2 ASD 25 ASD 30 ASD 40S ASD 40

Tab. 13 Cooling oil charge (Option W2)