Catalogo Rancho Estabilizador
Catalogo Rancho Estabilizador
Catalogo Rancho Estabilizador
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
CHEVROLET
CHEVROLET TRUCK — Avalanche 4 W.D.
2002-05 4WD Avalanche 1500 Sport Utility Pickup w/Rancho RS6547 System SINGLE — RS5402 RS5545
2002-05 4WD Avalanche 2500 Sport Utility Pickup SINGLE — RS5407 RS5548
2000-05 4WD Avalanche 2500 Sport Utility Pickup w/ O.E. Steering Stabilizer (Bolts to O.E. SINGLE — RS5411 —
Mounts)
Q2 Qty. Req. 2
58 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 59
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
CHEVROLET
CHEVROLET TRUCK — Pickup (3⁄4 Ton) 4 W.D. (Silverado, K & V Models) — Continued
1988-00 4WD K-2500 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97266 RS5401 RS5528
1988-00 4WD K-2500 (3⁄4 Ton) w/o O.E. Steering Stabilizer Mounts SINGLE RS97265 RS5401 RS5526
1988-98 4WD K-2500 (3⁄4 Ton) - 6 Lug w/Rancho RS6443 System SINGLE RS97343 RS5401 RS5543
1988-98 4WD K-2500 (3⁄4 Ton) - 8 Lug w/Rancho RS6469 System SINGLE — RS5401 —
1987 4WD V-20 (3⁄4 Ton) DUAL RS98501 RS5402Q2 RS5561
1987 4WD V-20 (3⁄4 Ton) - high performance stabilizer SINGLE RS97500 RS5408 RS5509
1987 4WD V-20 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97325 RS5404 —
1973-86 4WD K-20 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97325 RS5404 —
1967-86 4WD K-20 (3⁄4 Ton) DUAL RS98501 RS5402Q2 RS5561
1967-86 4WD K-20 (3⁄4 Ton) - high performance stabilizer SINGLE RS97500 RS5408 RS5509
1960-72 4WD K-20 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
1958-59 4WD Series III - 3600 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
Q2 Qty. Req. 2
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 59
Rancho Steering.qxd 4/12/05 2:35 PM Page 60
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
CHEVROLET
CHEVROLET TRUCK — Suburban 4 W.D. — Continued
1967-91 4WD Suburban - high performance stabilizer SINGLE RS97500 RS5408 RS5509
DANA
DANA AXLES — 4WD Front Steering Axles
— Dana #30 2 5⁄169 O.D. SINGLE RS97345 RS5402 RS5508
— Dana #44 2 3⁄49 ,75 mm O.D. SINGLE RS97355 RS5403 RS5509
— Dana #60 up to 3 1⁄29 O.D., Napco up to 3 3⁄89 O.D. SINGLE — RS5403 RS5512
DODGE
DODGE TRUCK — Pickup (1⁄2 Ton) 4 W.D. (Ram 1500 & W Models)
2000-05 4WD Ram 1500 (1⁄2 Ton) w/ O.E. Steering Stabilizer w/ OEM number 52106909AB, AC SINGLE — RS5412 —
& AD
1994-99 4WD Ram 1500 (1⁄2 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5404 —
1960-93 4WD W100, W150 (1⁄2 Ton) SINGLE RS97355 RS5403 RS5509
DUAL RS9850184 RS5402Q2 RS556184
DODGE TRUCK — Pickup (1⁄2 Ton) 2 W.D. (Ram 1500 & D Models)
2000-01 2WD Ram 1500 (1⁄2 Ton) SINGLE — RS5401 RS5570
1972-93 2WD D100, D150 (1⁄2 Ton) w/coil spring front suspension SINGLE RS97385 RS5402 RS5514
1954-71 2WD D100 (1⁄2 Ton) w/I-Beam axle SINGLE RS97345 RS5402 RS5508
DODGE TRUCK — Pickup (3⁄4 Ton) 4 W.D. (Ram 2500 & W Models)
2000-05 4WD Ram 2500 (3⁄4 Ton) w/ O.E. Steering Stabilizer w/ OEM number 52106909AB, AC SINGLE — RS5412 —
& AD
1994-99 4WD Ram 2500 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5404 —
1994-98 4WD Ram 2500 (3⁄4 Ton) - supplemental steering stabilizer w/ 8800 GVW SINGLE — RS5403 RS5541149
1960-93 4WD W200, W250 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
1960-93 4WD W200, W250 (3⁄4 Ton) DUAL RS9850184 RS5402Q2 RS556184
DODGE TRUCK — Pickup (3⁄4 Ton) 2 W.D. (Ram 2500 & D Models)
1972-93 2WD D200, D250 (3⁄4 Ton) w/coil spring front suspension SINGLE RS97385 RS5402 RS5514
Q2 Qty. Req. 2
60 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 61
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
DODGE
DODGE TRUCK — Pickup (3⁄4 Ton) 2 W.D. (Ram 2500 & D Models) — Continued
1954-71 2WD D200 (3⁄4 Ton) w/I-Beam axle SINGLE RS97345 RS5402 RS5508
DODGE TRUCK — Van (3⁄4 Ton) Ram & B Models - Inc. Wagon
1979-90 B200, B250 (3⁄4 Ton) SINGLE — RS5403 RS5518
1970-78 B200 (3⁄4 Ton) SINGLE — RS5403 RS5517
FORD
FORD TRUCK — Bronco (Full Size Models) 4 W.D.
1992-96 4WD Bronco SINGLE RS97489123 RS5402 RS5566123
1992-96 4WD Bronco DUAL RS98508123 RS5402Q2 RS5565123
1990-92 4WD Bronco — Exc. Quad Susp. SINGLE — RS5402 RS5537
1980-92 4WD Bronco w/ Quad Susp. SINGLE RS97489123 RS5402 RS5566123
1980-92 4WD Bronco w/ Quad Susp. DUAL RS98508 RS5402Q2 RS5565
1980-91 4WD Bronco - max. 39 raised height DUAL RS98506 RS5402Q2 RS5563
1980-89 4WD Bronco SINGLE RS97481 RS5402 RS5535
1978-79 4WD Bronco - high performance stabilizer SINGLE RS97500 RS5408 RS5509
1978-79 4WD Bronco w/o sway bar DUAL RS985018 RS5402Q2 RS55618
Q2 Qty. Req. 2
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 61
Rancho Steering.qxd 4/12/05 2:35 PM Page 62
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
FORD
FORD TRUCK — Bronco (Full Size Models) 4 W.D. — Continued
1970-79 4WD Bronco w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97335 RS5403 —
1966-69 4WD Bronco w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97325 RS5404 —
Q2 Qty. Req. 2
62 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 63
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
FORD
FORD TRUCK — Pickup (3⁄4 Ton) 4 W.D. (F Series) — Continued
1977-79 4WD F-250 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE RS97445 RS5405 —
1959-77 4WD F-250 (3⁄4 Ton) - w/o power steering SINGLE RS97355 RS5403 RS5509
Q2 Qty. Req. 2
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 63
Rancho Steering.qxd 4/12/05 2:35 PM Page 64
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
GMC
GMC TRUCK — Jimmy 4 W.D. Compact - Inc. S Models
1995-00 4WD Jimmy w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5401 —
1995-97 4WD Jimmy w/o O.E. Steering Stabilizer Mounts SINGLE RS97265 RS5401 RS5526
1982-94 4WD Jimmy (S Models) Mid Size w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5401 —
1982-94 4WD Jimmy (S Models) Mid Size w/o O.E. Steering Stabilizer Mounts SINGLE RS97265 RS5401 RS5526
Q2 Qty. Req. 2
64 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 65
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
GMC
GMC TRUCK — Pickup (3⁄4 Ton) 4 W.D. (Sierra, K & V Models) — Continued
1967-72 4WD 1500 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
1960-66 4WD 1500 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
1958-59 4WD 150 (3⁄4 Ton) SINGLE RS97355 RS5403 RS5509
Q2 Qty. Req. 2
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 65
Rancho Steering.qxd 4/12/05 2:35 PM Page 66
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
GMC
GMC TRUCK — Yukon XL 4 W.D.
2000-05 4WD Yukon XL 1500 (1⁄2 Ton) w/Rancho RS6546 or RS6547 System — Exc. Z55 SINGLE — RS5402 RS5545
Autoride Suspension
2000-05 4WD Yukon XL 2500 (3⁄4 Ton) (Up To 8600 GVW) SINGLE — RS5407 RS5548
2000-05 4WD Yukon XL 2500 (3⁄4 Ton) w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5411 —
HUMMER
HUMMER — H2
2003-05 4WD H2 SINGLE — RS5407 RS5548
INTERNATIONAL HARVESTER
INTERNATIONAL HARVESTER — Pickup (Full Size) 4 W.D.
1960-75 4WD IHC Pickup w/31⁄29 front axle and 11⁄29 tie rod SINGLE — RS5403 RS5512
1960-75 4WD IHC Pickup (1⁄2, 3⁄4 Ton) - all others SINGLE RS97355 RS5403 RS5509
ISUZU
ISUZU TRUCK — Amigo 2 W.D.
1989-97 2WD Amigo SINGLE RS97270 RS5401 RS5503
66 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 67
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
ISUZU
ISUZU TRUCK — Rodeo 2 W.D.
1989-97 2WD Rodeo SINGLE RS97270 RS5401 RS5503
JEEP
JEEP — Cherokee
1984-98 XJ Cherokee Mid Size All w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5401 —
LAND ROVER
LAND ROVER — Defender 90
1984-89 909, 1109 W.B. & Defender SINGLE — RS5405 RS5550
1959-81 889, 909, 1109 W.B. SINGLE RS97435 RS5402 RS5520
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 67
Rancho Steering.qxd 4/12/05 2:35 PM Page 68
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
LAND ROVER
LAND ROVER — Range Rover
1984-92 Range Rover 909 All SINGLE — RS5405 RS5550
MAZDA
MAZDA TRUCK — Navajo 4 W.D.
1990-94 4WD Navajo SINGLE RS9748366 RS5402 RS553766
MITSUBISHI
MITSUBISHI TRUCK — Montero 4 W.D.
1986-95 4WD Montero SINGLE — RS5402 RS5508
NISSAN
NISSAN TRUCK — Frontier 4 W.D.
2000-02 4WD Frontier SINGLE — RS5402 RS5592
68 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Steering.qxd 4/12/05 2:35 PM Page 69
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
NISSAN
NISSAN TRUCK — Terrano 4 W.D.
July 86-95 4WD Terrano w/o O.E. Steering Stabilizer Mounts SINGLE RS97268 RS5402 RS5533
OLDSMOBILE
OLDSMOBILE — Bravada 4 W.D.
1991-97 4WD Bravada w/ O.E. Steering Stabilizer (Bolts to O.E. Mounts) SINGLE — RS5401 —
1991-97 4WD Bravada w/o O.E. Steering Stabilizer Mounts SINGLE RS97265 RS5401 RS5526
PLYMOUTH
PLYMOUTH TRUCK — Arrow (Light Duty) Pickup 2 W.D.
1982 2WD Arrow Mini SINGLE RS97260 RS5402 RS5502
SUZUKI
SUZUKI — Samurai 4 W.D.
1985-90 4WD Samurai SINGLE RS97345 RS5402 RS5508
1978-88 4WD LJ10, SJ10 SINGLE — RS5402 RS5508
1982-87 4WD LJ413 SINGLE — RS5402 RS5508
TOYOTA
TOYOTA TRUCK — 4 Runner
1990-93 2WD 4 Runner SINGLE RS97273 RS5402 RS5573
1986-93 4WD 4 Runner SINGLE RS97273 RS5402 RS5573
1984-85 4WD 4 Runner SINGLE RS97484 RS5403 RS5525
Q2 Qty. Req. 2
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 69
Rancho Steering.qxd 4/12/05 2:35 PM Page 70
Steering Stabilizers
COMPLETE RS5000
YEAR MODEL TYPE KIT SHOCK BRACKET
TOYOTA
TOYOTA TRUCK — 4 Runner — Continued
1979-85 4 Runner All DUAL RS9850560 RS5402Q2 RS556260
Q2 Qty. Req. 2
70 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Footnotes.qxd 4/12/05 2:32 PM Page 105
4. Check the Shock Application section for the correct shocks used on 20. Additional washers may be required to increase space between shocks
vehicles which come equipped with OE Quad Suspension or Add on on lower mount.
Dual Shock Option.
21. On 1976-81 CJ5, CJ7, Scrambler 2 1⁄29 Suspension System RS5119 &
5. On CJ’s with 4 speed transmissions, rear driveline will need to be RS99119 may be too short and you must use RS5113 & RS99113 with
lengthened, transfer case cross member will need to be lowered from Bump Stop Kit No. RS8203.
frame 1⁄29 and driveline vibration will occur. Use Lowering Bracket Kit to
lower transfer case 1⁄29. Part No. RS6633 fits 1941-1975. Part No. RS6639 22. Part No. RS8125 axle shim kit may be required on rear axle for shock-to-
fits 1976-1986. axle clearance.
6. If these vehicles have a Detroit-type driveline, the driveline must be 23. I.D. of shock bushing is smaller than mounting pin & requires lubrication
replaced by a Spicer-type driveline. & extra effort for installation.
25. Steering arm may contact shock body on RS5113, RS5119, RS99113
& RS99119 on FJ43 & FJ45. Install shock boot towards ground for
7. On some models a low speed vibration may occur in the front driveline. additional clearance.
8. If tie rod assembly is Diagram 1 - inverted “Y” it must be changed to 26. This Spring is required with the Primary Suspension System, to get the
Diagram 2 later model, 1978-79, inverted “T” style, (see below). CAUTION: proper lift.
SOME VEHICLES WILL BE UNABLE TO CHANGE TO THE INVERTED “T”,
THEREFORE A DUAL STABILIZER OR A SUSPENSION SYSTEM 27. Bumpstop must be lowered 29 or damage to shock will occur.
CANNOT BE INSTALLED. VEHICLES EQUIPPED WITH A POWER
STEERING CYLINDER CANNOT BE CONVERTED TO THE INVERTED “T”. 28. Must have factory hole in tie rod for stabilizer.
29. We recommend installing new ball joints when installing Part No.
RS6500.
30. Kit RS60612 will work on 1983-86 Nissan but raises rear 29-39.
9. Rancho highly recommends the use of the constant velocity (Spicer
style) front driveshaft, as used in the Jeep factory trailer towing 31. 1967-72 Chevrolet/GMC Trucks may be equipped with a non-adjustable
option.The Jeep original equipment, light duty, double offset joint, front drag link. In these cases the drag link will need to be replaced with a late
driveshaft should not be used if any of the following conditions occur. If model Chevrolet/GMC adjustable link, available through your Chevrolet
you have Select-Track Option. If you drive 55-65 mph for long periods of or GMC dealer.
time.You tow a trailer.You use your vehicle to pull other vehicles out
from being stuck. If you use the light duty driveshaft you will experience 32. On Blazer/Jimmy with worn or sagging rear springs, vehicle will sit low
driveshaft boot wear and will need to re-pack the offset joint periodically in rear.Rear Add-A-Leaf part No. RS60812 will correct this.
and replace the boot periodically.
34. RS996 Rockcrawler Bushing Rebuild Kit is Available (Rebuilds one Link -
10. 1987-90 4WD Blazer or Jimmy and short bed pickups with a 49 4 Kits required for completed vehicle.)
suspension system will require a transfer case lowering kit part number
RS6640. Some vehicles equipped with 2 1⁄29 suspension system may 35. Height will vary due to inconsistent factory height.
experience a driveline vibration. Part number RS6640 can be used to
possibly correct the vibration, but a driveline vibration may still be 36. On M38, vehicle spring anchor mounts will need to be drilled out and you
present.The exhaust cross pipe will need to be modified to clear front must buy Jeep spring anchor bolt Part No. RS384228 (4 per vehicle) to
drive shaft. install springs. Available from your Jeep dealer.
11. RS8701 is required to restore the turning radius, on right turns. 37. Remove 1⁄29 O.D. x 7⁄169 I.D. sleeves, if used, from the old spring shackle
ends and insert sleeves into the Rancho bushings.
12. If the rear of your vehicle is equipped with a height-sensitive brake
proportioning valve, contact your local dealer for correct adjustment 38. On all Dodges, the use of our Kicker Shock Kit No. RS1804 is required to
procedure of the proportioning valve. CAUTION: VEHICLES WITH NO greatly reduce rear end windup.
ADJUSTMENT PROCEDURE, RANCHO DOES NOT RECOMMEND
INSTALLATION OF THE ADD-LEAF OR LEV-A LOAD. 39. Vehicles equipped with GM’s Auto Trak system WILL REQUIRE the
replacement of the front drive shaft or else severe drive line vibration
13. Block Kit No. RS70054 is required with RS86209 Rear Spring for a 49 lift. and noise will occur. Rancho recommends “Powertrain Industries” part
number 3194-9800 or equivalent. Available from: Powertrain Industries,
14. Full Size Lev-A-Load Kits will not fit vehicles with factory overload Inc. 7532 Anthony Ave. Garden Grove, CA 92841.Toll Free: 1-800-798-
mounted above leaf spring. 4585. Email: [email protected].
15. Vehicles with a 13 1⁄49 rear driveshaft will require a transfer case lowering 40. May need longer rear U-bolt Kit RS737. 89-91 standard cab, short bed
kit RS6644. Toyota requires U-bolt Kit RS745.
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 105
Rancho Footnotes.qxd 4/12/05 2:32 PM Page 106
51. Not recommended for XJ Cherokee or Comanche with 3 leaf springs. 114. For use on stock vehicle, use adaptor kit RS6614.
59. You must use soft-valved RS5000 shock absorbers 118. For installation of 339 tires use Bump Stop Spacer Kit RS744.
listed.Corresponding RS9000X’s must be set on 1 or 2.
119. For installation of 339 tires use Bump Stop Spacer Kit RS8229.
60. Not recommended on vehicles without power steering.
120. Camber adjustment may not be possible on some raised vehicles.
61. Rear block kit, Part No. RS73044 may be required. If RS73044 is used, RS6406 coil springs will only work on raised vehicles.
Shock RS5118 will be required.
122. Requires O.E. replacement bushings.
64. RS1902 adjustable torque rod S-link kit is required.
123. Most 92-96 fullsize 4WD Bronco and F-150 trucks are equipped with the
66. This kit does not fit vehicles which are equipped with factory high rider lower mount of the factory quad shock option, which is needed to
package (IRH) or vehicles with an aftermarket pitman arm with more mount our RS97489, RS98508, RS5565 & RS5566 steering stabilizer
than 1 1⁄49 off-set. systems.
70. RS5600 series shocks are 1 3⁄169 bore. 124. If vehicle has 2 1⁄29 wide leaf springs, use Bracket Kit RS50616.
77. RS1802 Kicker Shock fits 1984-1986 Toyota only after the removal of the 125. ’87 and newer may only restore stock height.
welded-on bump stop striker plate located on the frame and installation
of Rancho Bump Stop included in RS1802 Kit. 126. 460 gas with Super Cab or accessories like a winch, etc. Call for
application.
79. Our torsion bars are heavy duty to resist sag when adjusted to
maximum height.Vehicle may not be raised, and rear Add-A-Leaf may 128. Sway Bar Mount Spacer Kit No. RS8228 required with automatic
not be needed. transmission.
80. Most CJ2A, CJ3A, CJ3B, MB, M38, M38A1 have a sideways U-type 131. Height may be taller for non-race prepared vehicles.
shackle which must be upgraded to plate-type shackle.Our shackle kit
also includes the urethane bushings for your frame. Since stock 114. Some earlier model vehicles requie newer alignment eccentrics.
bushings are usually worn, our shackle kit Part No. RS6636 is highly
132. These leaf springs do not come with bushings. Bushings are in front
recommended (one kit per axle).
Kit RS6444.
81. Front kit Part No. RS726 includes two tie rod ends Part No. RS7600.
133. Transfer case Lowering Kit No. RS6641 may be required on some
83. Jeeps use stock location with no drilling. vehicles.
84. This kit will not fit vehicles which have a vacuum servo mounted on 134. Wranglers with 9Off-Road Suspension9 option (code AWE) will be 19
drivers side of the front axle. less. Also, vehicles with a hard top &/or a V-8 may not achieve full
raised height.
88. Kit includes front and rear U-bolts.
135. Exhaust modification may be necessary.
89. Hole drilling or bracket modifications may be required on some
vehicles. 139. DO NOT use with composite spring.
91. Kit includes both front and rear U-bolt kits.U-bolts are 9⁄169, you will have 140. Use RS6676 Heavy Duty Upper & Lower Link System for improved
to drill your spring plates. cornering and overall handling characteristics on stock height vehicles.
92. Factory rear springs must have a flat measurement eye to eye of 142. Front upper and lower link kit, replacement for stock links.
529.Some heavy duty rear springs measure 569 flat and cannot be
145. Optional Skid Plate Kit Part No. RS1625 is recommended for on/off road
replaced.
use, it will only fit with Rancho Suspension System.
95. Rancho rear block kit RS82054 may be required for this application.
146. Optional Upper Link Kit for added performance and handling.
96. This is a unique 2 leaf Add-A-Leaf system that raises the vehicle
148. Do not use with after market (stamped steel housing) ball joints. Use
approximately 19- 29, depending upon options.
only with OE style (forged housing construction) upper ball joints.
100. Except dual rear wheels
149. This unit installs in an auxilliary position and may be used in
101. Rancho U-bolt Kit RS722 may be required if dual Add-A-Leaf’s are conjunction with the O.E.M. position stabilizer.
installed on 1980 and newer vehicles.
150. This component is optional, and is recommended for optimum
102. This system is only sold as a complete kit!Individual components will performance.
not be sold separately.For warranty of individual components, send
106 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS.
Rancho Footnotes.qxd 4/12/05 2:32 PM Page 107
154. Exhaust modification is required, check local laws regarding exhaust 202. Optional Skid Plate can be purchased separately.
modification prior to installation.
203. RS6740 or RS6741 Bracket Kit includes four RS5298 shocks.
155. Part number RS40054S may be substituted for RS86206 applications.
This spring will give a firmer ride and will have limited suspension 205. Ford Superduties are equipped from the factory with either a “tall” (3.79)
travel. rear block or a “short” (1.99) rear block. Rancho offers three different
choices to accomodate this option.
156. These springs are not designed for hauling. 1. RS44154: Soft ride rear leaf spring is designed to add up to 1" of
rear height.
161. 95 and later Grand Cherokees (ZJ) front driveshaft 2. R80053: Rear block kit adds 2 1⁄29 to rear height on vehicles equipped
replacement.Driveshafts that measure over 24 1⁄29, No change required. with the O.E. “short” block and 19 to vehicles equipped with
Driveshafts that measure from 209 up to 24 1⁄29, May require a change. O.E. “tall” bloack.
Test drive vehicle, change to Spicer type if a vibration is present. 3. RS60642: Rear add-a-leaf kit is designed to add up to 2" of rear
Driveshafts that measure under 209, Must change to a Spicer type. height.
CAUTION: VEHICLES WITH A DRIVESHAFT UNDER 209 MAY STILL
EXPERIENCE A VIBRATION EVEN AFTER CHANGING TO A SPICER- 206. Installation of this suspension system on 99 and later vehicle equipped
TYPE DRIVESHAFT. with full-time 4WD (A4WD) may provide a slightly more noticeable level
of driveline vibration.To offset any driveline vibration, replacement
front driveshaft (part number 3191-1001) is available from: Powertrain
Industries, Inc. 7532 Anthony Ave. Garden Grove, CA 92841.Toll Free: 1-
800-798-4585. Email: [email protected].
162. May substitute Add-A-Leaf RS60611 with 3 leaf rear spring (94-early 96 207. Springs are not included with this system and must be ordered
only). separately.
163. Spring Seat Shock included in front kit. 208. This system does not allow the reuse of O.E. factory 159 wheels.
167. See Shock Absorber Section for Shock Application. 209. New upper ball joints are not included with this suspension kit but are
required to complete the installation, refernce instruction sheet for
173. 1996 & 1997 Model years REQUIRE 88025-REV. C or later installation complete listing.
instructions.
210. Some vehicles may experience a rear driveshalf vibration. A
177. Remove and replace #2 leaf. replacement rear double-cardan driveshaft for Rubicons only (part
number 3394-0100) is available from: Powertrain Industries, Inc. 7532
182. Has grease fittings. Anthony Ave. Garden Grove, CA 92841.Toll Free: 1-800-798-4585. Email:
[email protected].
184. 4 leaf only.
211. RS40054S may be used as a HD replacement.
185. Except 4000 lb front axle.
212. Adjustable height coil-over unit.
186. Will NOT Fit Vehicles with Rack and Pinion Steering.
213. Does not work on vehicles equipped with OE radiator skin plate.
187. Will NOT FIT vehicles with OE Pitman Arm YC35-3590-AA.This part
number is on the Pitman Arm. 214. Does NOT fit vehicles equipped with the Off-Road Suspension package.
189. Will FIT vehicles with OE Pitman Arm YC35-3590-AA.This part number A3. New Part Number Available Third Quarter
is on the Pitman Arm.
PS. Rancho RS9000X Pro-Series shock absorber.
190. Aft Subframe Braces RS6643 are available for additional support for off-
road use. Q2. Qty. Req. 2
192. Front Driveshaft vibartion may occur in 4 W.D. only. A replacement Q4. Qty. Req. 4
driveshaft (part no. 3194-1000) is available from: Powertrain Industries,
Inc. 7532 Anthony Ave. Garden Grove, CA 92841.Toll Free: 1-800-798- • New Part Number, Check availability before placing order.
4585. Email: [email protected].
a Installation of this system does not allow the re-use of OE (factory)
197. Ford F150’s which have a (“L” - shape bolt pattern for the transmission wheels.
cross member must use the RS6489 Primary Suspension System;
trangular bolt pattern use RS6488 Primary Suspension System.
199. This system cannot be used with any wheel with backspacing that
exceeds 4.59 and/or the wheel diameter is less than 169.
FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 107