Scribd Logo
Upload

Welcome to Scribd!

  • 32 views

    Screw Conveyor Applications VFD Settings: S.No Parameters Specification Set Value

    Uploaded by

    Praveen Choudhary
    The document provides VFD settings for screw conveyor applications. It lists 31 parameter settings for configuring the VFD, including settings for torque boost, maximum frequency, motor speeds, acceleration/deceleration times, overload protection levels, stall prevention operation, and motor configuration. The settings are tailored for operating two motors of 15kw capacity each with 4 poles at 415V rated voltage for screw conveyors.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Screw Conveyor Applications VFD Settings: S.No Parameters Specification Set Value

    Uploaded by

    Praveen Choudhary
    32 views1 page
    The document provides VFD settings for screw conveyor applications. It lists 31 parameter settings for configuring the VFD, including settings for torque boost, maximum frequency, motor speeds, acceleration/deceleration times, overload protection levels, stall prevention operation, and motor configuration. The settings are tailored for operating two motors of 15kw capacity each with 4 poles at 415V rated voltage for screw conveyors.

    Original Title

    Untitled

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides VFD settings for screw conveyor applications. It lists 31 parameter settings for configuring the VFD, including settings for torque boost, maximum frequency, motor speeds, acceleration/deceleration times, overload protection levels, stall prevention operation, and motor configuration. The settings are tailored for operating two motors of 15kw capacity each with 4 poles at 415V rated voltage for screw conveyors.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    32 views1 page

    Screw Conveyor Applications VFD Settings: S.No Parameters Specification Set Value

    Uploaded by

    Praveen Choudhary
    The document provides VFD settings for screw conveyor applications. It lists 31 parameter settings for configuring the VFD, including settings for torque boost, maximum frequency, motor speeds, acceleration/deceleration times, overload protection levels, stall prevention operation, and motor configuration. The settings are tailored for operating two motors of 15kw capacity each with 4 poles at 415V rated voltage for screw conveyors.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    SCREW CONVEYOR APPLICATIONS VFD SETTINGS

    S.NO PARAMETERS SPECIFICATION SET VALUE


    1 P0 Torque Boost 2.5 HZ
    2 P1 Maximum frequency 50hz
    3 p4 motor 1 low speed 35hz
    4 P5 motor 2 low speed 30hz
    5 P7 Acceleration time 1sec
    6 P8 deacceleration time 1.0sec
    7 P9 Electronic thermal O/L relay first motor 28 Amps
    8 P13 Starting frequency 0hz
    9 P14 Load pattern Selection 1
    10 P18 High speed maximum frequency 50hz
    11 P19 base frequency voltage 9999
    12 P22 Stall prevention operation selection 200%
    13 P24 motor 2 high speed 50hz
    14 P25 motor 1 high speed 50hz
    15 P29 Acceleration&deacceleration pattern selection 2
    16 P44 second acceleration time 1sec
    17 P45 second deacceleration time 1.6sec
    18 P46 second torque boost 2%
    19 P47 second V/F (base frequency) 50hz
    20 P48 second stall prevention operation level 150%
    21 P51 Second Electronic thermal O/L relay
    22 P79 operation mode selection 3
    23 P80 motor capacity 15 kw
    24 P81 NO.of motor poles 4
    25 P83 rated motor voltage 415
    26 P89 speed control gain(advanced magnetic flux vector) 200
    27 P183 MRS terminal function 3
    28 P190 RUN terminal function selection 0
    29 P292 automatic acceleratin /deacceleration 0
    30 P450 second applied motor 0
    31 P571 Holding time at astart 9999

    Note: P51 To be set depends on FLY ASH MOTOR Amps rating

    You might also like