Multi V Trouble Shooting Guide Book - 0912

2009.
12
Troubleshooting Guide
-1-
No part of this publication may be reproduced, stored in or introduced into a retrieval
system, or transmitted, in any form, or by any means (electronic, mechanical, photocopying,
or otherwise), without prior permission of the LG Electronics Inc. Air-Conditioning Division
-2-
Contents
Search with Error Code number .................................…............... 4
1. Basic Part ..............................................................……............... 5

1.1 Unit conversion (Energy / Pressure) .........................……......…... 6
1.2 NOMENCLATURE ………………………………………………………………….. 7
1.3 LGMV Guideline .......................................................……........... 13
1.4 Temperature vs. pressure of refrigerant.......................……......... 14
1.5 P-h Diagram …………...............................................……............. 15
1.6 Cycle Circuit & Sensor …………..................................……............ 16
1.7 Outdoor Wiring Diagram ...............................…...............……….. 30
2. Troubleshooting Guide for each Error Code (Refer page 4) …. 43
3. Electric Component Check ........................................................ 172

3.1 How to check main control box? ................................……........... 173
3.2 How to check inverter control box? ............................……........... 180
3.3 How to check Multi V Space control box? …………………………………. 187
3.4 How to check indoor unit PCB? ............………..............……........... 190
3.5 How to check other electric components ......................……......... 191
4. Solution Check ........................................................................... 199

Central control structure...................................................…............ 200
A- Installation guide…………………… ..................................……......... 201
B- Trouble shooting.......................................................……............ 218
C- Technical bulletin ..................................................…................. 258
5. Test functions (Plus II) ………………………………………………………….. 277

5.1 Sensor checking ……………………………………………………………………. 281
5.2 Auto charging ……………………………………………………………………….. 283
5.3 Auto refrigerant checking ………………………………………………………. 285
5.4 Pump down …………………………………………………………………………… 287
5.5 Pump out………………………………………………………………………………… 288
5.6 Vacuum mode ……………………………………………………………………….. 290
5.7 Static pressure compensation mode….………………………………………..290
5.8 Pipe searching ………………………………………………………………………..291
5.9 Manual setting example …………………………….……………………………..295
Appendix #1 : Resistance value table of temperature sensor ………296
-3-
Search with Error Code number
R: Reserved
Error Error Error Error Error Error Error
Page Page Page Page Page Page Page
code code code code code code code
01 45 41 102 81 121 102 161 105 201 168 241 170
02 45 42 104 82 122 102 162 102 202 168 242 170
03 45 43 104 83 R 123 105 163 102 203 168 243 170
04 47 44 105 84 124 105 164 105 204 169 244 170
05 49 45 105 85 125 148 165 105 205 168 245 170
06 50 46 105 86 132 126 148 166 148 206 168 246 170
07 50 47 105 87 133 127 148 167 148 207 168 247
08 R 48 105 88 128 104 168 148 208 169 248 R
09 51 49 107 89 129 104 169 95 209 168 249
10 52 50 108 90 130 105 170 98 210 168 250 171
11 53 51 109 91 131 R 171 83 211 168 251 171
12 52 112 92 132 105 172 107 212 169 252 171
13 53 113 93 133 102 173 155 213 168 253 171
R
14 54 114 94 134 102 174 155 214 168 254
15 55 95 135 105 175 155 215 168 255
16 R 56 96 136 105 176 155 216 169 256
R
17 57 97 137 148 177 155 217 168 257
18 58 98 138 148 178 218 168 258
R
19 59 116 99 139 148 179 219 168 259
20 60 117 100 134 140 79 180 156 220 169 260
21 65 61 R 101 134 141 104 181 157 221 168 261
22 73 62 118 102 134 142 135 182 158 222 168 262
23 77 63 103 134 143 95 183 223 168 263
R
24 79 64 104 135 144 98 184 224 169 264
25 83 65 119 105 137 145 95 185 225 168 265
26 84 66 R 106 139 146 98 186 226 168 266
27 R 67 120 107 145 147 83 187 227 168 267 R
R
28 85 68 108 R 148 107 188 228 169 268
R
29 86 69 109 147 149 83 189 229 168 269
30 70 122 110 147 150 107 190 230 168 270
R
31 71 123 111 147 151 151 191 231 168 271
32 88 72 R 112 R 152 88 192 232 169 272
33 88 73 124 113 148 153 88 193 159 233 273
34 95 74 126 114 148 154 79 194 159 234 274
35 98 75 127 115 148 155 114 195 235 275
36 76 128 116 149 156 135 196 236 R 276
37 77 129 117 149 157 104 197 R 237 277
R
38 78 130 118 105 158 104 198 238 278
39 79 131 119 R 159 105 199 239 279
40 100 80 R 120 105 160 R 200 160 240 170 280
-4-
Troubleshooting Electrical
Basic Part Guide for each Component Check Solution Check Test functions
Error Code
Basic Part
-5-
1
.
Error Code
-6-
1.1 UNIT CONVERSION
Error Code
1.2.2 Multi V Plus Outdoor Unit (R410A)
-7-
1.2.1 Multi V Indoor Unit (R410A)
1.2 NOMENCLATURE
Error Code
1.2.4 Multi V Plus II Outdoor Unit (R410A)
1.2.3 Multi V Plus II Outdoor Unit (R410A)
-8-
Error Code
1.2.6 Multi V Space II Outdoor Unit (R410A)
1.2.5 Multi V Space Outdoor Unit (R410A)
-9-
Error Code
1.2.8 Multi V Sync II Outdoor Unit (R410A)
1.2.7 Multi V Sync Outdoor Unit (R410A)
-10-
1.2.9 Multi V Mini Outdoor Unit (R410A)
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
1.2.10 Multi V Water II Outdoor Unit (R410A)
Electrical
Solution Check
B: Inverter and Heat Recovery

Test functions
-11-
Error Code
1.2.12 Multi V Plus Outdoor Unit (R22)
-12-
1.2.11 Multi V Indoor Unit (R22)
1.3 LGMV Guideline
Basic Part
Abnormal Abnormal
No Item Unit R22,407C 410A Cause & Check Point
condition condition
Overcharging(30Hz),Fan Lock
above 2200 above 3200
1 High Pressure kPa 1100~1800 2000 ~ 3000 Overchaning(25Hz:Plus II)
below 900 below 1800 Ref. Leakage or Ref. Shortage
Low Pressure above 600 above 1300 Overcharging
2 kPa 300~500 600 ~ 1000
(Cooling) below 250 below 400 Ref. Leakage or Ref. Shortage
above 1000 above 1000 Ref. Leakage or Ref. Shortage
3 Indoor LEV Pulse 200~600 200~600
below 200 below 200 Overcharging
4 Outdoor LEV Pulse 1944 - 1344 - Full Open
Indoor pipe Overcharging
5 ℃
Troubleshooting
above 0℃ below -1℃ above 0℃ below -1℃
[Outlet-inlet]
Guide for each

LEV fault
Error Code
Indoor pipe Ref. Leakage,
6 ℃ 8℃~15℃ above 17℃ 6℃~15℃ above 17℃
Inlet,Outlet Indoor Path. Clogging
Overcharging
High Pressure above 2300 above 3300
7 kPa 1600~2000 2500 ~ 3200 Fan Lock
(Heating)
above 800 above 1200 LEV fault
8 Low Pressure kPa 200~600 200 ~ 1200
9 Indoor LEV Pulse 800~1900 - 200~1350 - Pipe Inlet/outlet Subcooling control
300~1600 below 200 below 200 Overcharging

10 Outdoor LEV ℃ 200~800
(100~400) above 1800 above 1000 Ref. Leakage or Ref. Shortage
Component Check
Discharge pipe - Overcharging
11 ℃ above 15℃ below 15℃ above 17℃ below 17℃
Tb(condense) LEV fault
Electrical
above 110℃ above 110℃ Ref. Leakage or Ref. Shortage
12 Comp. Discharge T. ℃ 60~100 60~100
below 50℃ below 50℃ LEV fault
Suction above 0.5℃ below 0℃ below 0℃ Liquid compression, Overcharging
13 ℃ above 0.5℃
Superheat above 7℃ above 7℃ Ref. Leakage or Ref. Shortage
above 380V Below 320V Inv. PCB fault,
14 DC Link voltage(Plus II) V
Above 700V Voltage sensor fault
Solution Check
Test functions
- The pressure is relative value.

- The operation ratio of indoor unit is not less than 80% and the value of above table is measured at stable state with LGMV
- The value of above table is not absolute and can be changed according to operation status or installation environment
- The causes of above table are representative and another cause also can exist.
-13-
1.4 Temperature vs. pressure of ref.
Saturation temperature vs. saturation pressure table for
each refrigerant
Basic Part
Absolute pressure = Guage pressure + 101.325 kPa
kPa = kgf/cm2 X 101.97
R-22 R-407C
Relative Relative
Temp. Temp. Relative pressure(kPaG) Temp.(℃)
Pressure pressure
Saturated Saturated Saturated
℃ kPaG ℃ Saturated Gas kPaG
Liquid Liquid Gas
-30 62.56 -30 86.75 37.87 50 -35.26 -28.35
-25 100.11 -25 129.50 72.67 100 -28.52 -21.75
Troubleshooting
-20 143.99 -20 179.43 113.92 150 -22.99 -16.34
Guide for each

-15 194.87 -15 237.28 162.41 200 -18.25 -11.71
Error Code
-10 253.46 -10 303.86 218.96 250 -14.09 -7.64
-5 320.48 -5 378.98 284.43 350 -6.98 -0.69
0 396.66 0 466.50 359.72 400 -3.87 2.35
5 482.78 5 564.29 445.77 500 1.71 7.78
10 579.62 10 674.25 543.56 600 6.63 12.57
15 687.99 15 797.30 654.12 750 13.09 18.85
20 808.69 20 934.41 778.51 850 16.94 22.59
25 942.59 25 1086.55 917.87 1000 22.17 27.67
30 1090.55 30 1254.72 1073.36 1150 26.91 32.24
35 1253.46 35 1439.97 1246.28 1300 31.23 36.42
Component Check
40 1432.25 40 1643.37 1437.87 1550 31.23 36.42
45 1627.89 45 1866.04 1649.67 1750 42.42 47.18
Electrical
50 1841.36 50 2109.14 1883.24 2000 47.78 52.30
55 2073.75 55 2373.87 2140.33 2250 52.69 56.97
60 2326.16 60 2661.51 2422.98 2550 58.09 62.08
65 2599.83 65 2973.36 2733.60 2850 63.05 66.74
70 2896.07 70 3310.77 3075.22 3200 68.38 71.69
R-410A
Relative
Temp. Relative pressure(kPaG) Temp.(℃)
pressure
Saturated Saturated Saturated
℃ Saturated Gas kPaG
Liquid Liquid Gas
Solution Check
-30 169.62 168.91 170 -30.09 -30.02
-25 229.70 228.81 230 -25.08 -25.01
-20 299.57 298.46 300 -20.06 -19.99
-15 380.23 378.87 380 -15.09 -15.01
-10 472.75 471.09 470 -10.21 -10.12
-5 578.21 576.21 580 -4.98 -4.89
0 697.76 695.38 700 0.04 0.13
5 832.60 829.77 830 4.86 4.96
10 983.94 980.63 980 9.84 9.94
15 1153.09 1149.25 1150 14.88 14.98
20 1341.39 1336.98 1350 20.18 20.29
25 1550.25 1545.26 1550 24.96 25.08
Test functions
30 1781.19 1775.59 1800 30.36 30.47

35 2035.78 2029.59 2000 34.30 34.42
40 2315.76 2309.03 2300 39.71 39.82
45 2623.00 2615.82 2600 44.62 44.73
50 2959.61 2952.13 2950 49.84 49.95
55 3328.02 3320.49 3400 55.91 56.01
60 3731.18 3724.00 3700 59.61 59.70
65 4173.11 4166.98 4200 65.28 65.34
70 4746.09 4706.31 4700 70.17 70.17
-14-
Error Code
-15-
R410A
R22
1.5 P-h Diagram
Error Code
-16-
1.6.1.1 Main Outdoor Unit(5/6 HP)
1.6 Cycle Circuit & Sensor
1.6.1 Multi V Plus, Plus II
Error Code
1.6.1.2 Main Outdoor Unit (Plus II 8HP)
-17-
Error Code
1.6.1.3 Main Outdoor Unit (Plus 8~14HP, Plus II 10~16HP)
-18-
Error Code
1.6.1.4 Sub Outdoor Unit (Plus 8/10/12/14 HP)
-19-
Error Code
-20-
1.6.2 Multi V Sync, Sync II
1.6.2.1 Cooling Mode
Error Code
-21-
1.6.2.2 Heating Mode
Error Code
1.6.2.3 Cooling Oriented Simultaneous Operation
-22-
Error Code
1.6.2.4 Heating Oriented Simultaneous Operation
-23-
Error Code
-24-
1.6.3 Multi V Space (10HP)
Error Code
1.6.4 Multi V Space II (8, 10HP cooling only)
-25-
Error Code
-26-
1.6.5 Multi V MINI (4HP/5HP/6HP)
Cooling operation
Error Code
-27-
1.6.6 Multi V MINI (4HP/5HP/6HP)
Heating operation
Error Code
-28-
1.6.7 Multi V Water II H/P (10HP)
Error Code
-29-
1.6.8 Multi V Water II H/P (20HP)
Error Code
-30-
1.7. Outdoor Wiring Diagram
1.7.1.1 Multi V Plus Main Unit

1.7.1 Multi V Plus
Error Code
1.7.1.2 Multi V Plus II Sub 5,6HP(UY2)
-31-
Error Code
-32-
1.7.1.3 Multi V Plus II 8HP(UW1)
Error Code
1.7.1.4 Multi V Plus II 10,12,14,16HP(UW1)
-33-
Error Code
1.7.1.5 Multi V Plus II 10,12HP(UW1)
-34-
Error Code
-35-
1.7.1.6 Multi V Plus Sub Unit
Error Code
-36-
1.7.2.1 Multi V Space
Error Code
-37-
1.7.2.2 Multi V Space II
Error Code
-38-
1.7.3.1 Multi V Sync Main Unit
1.7.3 Multi V Sync
Error Code
-39-
1.7.3.2 Multi V Sync Sub Unit
Error Code
-40-
1.7.4 HR Unit
Error Code
-41-
1.7.5 Multi V MINI
Error Code
-42-
1.7.6 Multi V Water II
2
Basic Part
.
Troubleshooting
Troubleshooting
Guide for each
Error Code
Guide for each
Error Code*
Component Check
Electrical
Solution Check
Test functions
*Included model :
Multi V Plus, Sync, Sync II, Plus II (Tropical), Water
-43-
[Cautions when measuring voltage and current of inverter power circuit]
Measuring values may differ depending on measuring tools and measuring circuits since voltage,
current in the power supply or output side of the inverter has no since waveform.
Especially, output voltage changes when output voltage of the inverter has a pattern of pulse wave.
Basic Part
In addition, measuring values appear largely differently depending on measuring tools.
1) If using a movable tester when checking that output voltage of the inverter is constant (when
comparing relative voltage between lines), always use an analog tester. Especially exercise particular
caution if the output frequency of the inverter is low, when using a movable tester, where change of
measured voltage values is large between other lines, when virtually same values appear actually or
where there is danger to determine that failure of the inverter occurred.
2) You can use rectification voltmeter ( ) if using commercial frequency tester when measuring
output values of the inverter (when measuring absolute values). Accurate measuring values cannot
be obtained with a general movable tester (For analog and digital mode).
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-44-
Error code Error Contents Meaning Main Causes
01 Indoor unit air sensor error

1. Indoor unit PCB wrong connection
Indoor unit sensor is
02 Indoor unit pipe inlet sensor error 2. Indoor unit PCB failure
open/short
3. Sensor problem (main reason)
06 Indoor unit pipe outlet sensor error
Basic Part
Error diagnosis and countermeasure flow chart
Is sensor properly No
Connect properly to PCB
connected to PCB?
Yes
Troubleshooting
No
Guide for each

Is the resistance value
Change the sensor
Error Code
of sensor normal?*
Yes
Change the PCB
* In case the value is more than 100 ㏀ (open) or less than 100 Ω(short), Error occurs
Refer: Resistance value maybe change according to temperature of temp sensor,
Component Check
It shows according to criteria of current temperature(±5% margin) → Normal
Air temp sensor: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Electrical
Pipe temp sensor: 10℃ = 10㏀ : 25℃= 5㏀ : 50℃= 1.8㏀
CN-ROOM : Indoor air temp sensor
CN-PIPE2 : Pipe outlet temp sensor
CN-PIPE1 : Pipe inlet temp sensor
Solution Check
Measure the resistance of outlet pipe temp sensor.

Test functions
-45-
1. Remote controller fault

The remote controller did not 2. Indoor unit PCB fault
No transmission between cabled remote
03 receive the signal from indoor 3. Connector fault, Wrong
controller & indoor unit
unit during specific time connection
4. transmission cable problem
Basic Part
Does the error happens No

Replace cabled remote
again if the remote
controller
controller is replaced?*
Yes
Troubleshooting
Guide for each
Error Code
No
Does the error occurred
Check connection &
when the cable of remote
transmission cable **
controller is replaced?
Yes
Replace indoor unit PCB ***
* If there is no remote controller to replace : Use another unit’s remote controller doing well
Component Check
** Check cable : Contact failure of connected portion or extension of cable are main cause
Check any surrounded noise ( check the distance with main power cable)
Electrical
→ make safe distance from the devices generate electromagnetic wave
*** After replacing indoor unit PCB, do Auto Addressing & input unit’s address if connected to central controller.
(All the indoor units connected should be turned on before Auto Addressing
Solution Check
CN-REMO : Remote controller connection
※The PCB can differ from model to model.

Check from the right source.
Checking transmission cable connection status

Test functions
-46-
1. Drain pump/float switch fault

Float switch is open due to rising of
2. Improper drain pipe location,
04 Drain pump error condensate water level because of drain
clogging of drain pipe
pump fault or drain pipe clogging
3. Indoor unit PCB fault
Basic Part
Is the drain pan filled

No Is Float switch short No
half with condensate
On measuring its Replace float switch
water? (half level of
resistance?
float switch)*
Yes
Yes
Troubleshooting
Guide for each
Error Code
Replace Indoor PCB or
reconnect the connector
In indoor unit PCB

Is drain pump working? No No
Does the terminal voltage
(Sound/drain noise/ Replace indoor unit PCB
for drain pump has
contact etc.)
220V output?**
Yes Yes
Replace Drain Pump
Component Check
No
Drain pump blocked by Check the drain head height
foreign particles? and slope***
Electrical
Yes
Checking float
switch
Remove it & clean the pump (Low position  short ≒ 0 ohm )
Solution Check
*If the float goes up higher than a half of float switch

then the circuit is open & the unit is stopped
automatically.
(High position  Open )
float
Test functions
Condensate water
-47-
Basic Part
float
Troubleshooting
Guide for each
A:Point to check rotating ***Indoor PCB drain pump connector
Error Code
(Check input of 220V)
(Marked as CN-DPUMP)
Float switch connector
Component Check
Float switch Housing (CN-FLOAT)
Electrical
[***]Standard of drain pipe head height / slope
Solution Check
MAX 450
Test functions
-48-
1. Auto addressing is not done

2. transmission cable is not connected
No signal
Indoor & Outdoor 3. Short circuit of transmission cable
transmission
05 unit transmission 4. Indoor unit transmission circuit fault
between indoor
error 5. Outdoor unit transmission circuit fault
Basic Part
& outdoor units.
6. Not enough distance between power and transmission cable?
7. Is the fuse for main PCB power of outdoor unit burnt out?
Replace the PCB of indoor unit

No displayed error
No Is total number of indoor
Does all indoor show
units connected displayed Re-connect after check the
this error code CH05?
after auto addressing? transmission cable of indoor
Troubleshooting
unit displayed error**
Guide for each

Yes
Error Code
END
Replace outdoor PCB after
No Is not the power No checking
Is outdoor PCB LED
supplied at main terminal
flickering? Replace TRANS after checking
block of outdoor unit ?
Yes Replace main PCB fuse after

Yes checking
Check the insulation of inverter

No / constant compressor and then
Is main circuit breaker off?
Component Check
replace it
Yes Replace after capacity of
Electrical
main circuit breaker?
Bad connection of power supply cable
If nothing goes wrong,
Turn on main circuit breaker
Main power supply problem
Check if the
transmission
cable is properly No
Re connect transmission cable
connected
to indoor / outdoor
terminal block?*
Yes
Solution Check
Outdoor PCB fault
Replace after checking
Indoor PCB fault

Replace after checking
* If the DC voltage between transmission terminal A, B ** If the DC voltage between transmission terminal A, B
of outdoor unit is fluctuate within (-9V~+9V) then of indoor unit is fluctuate within (-9V~+9V) then
transmission from indoor unit is normal transmission from outdoor unit is normal
Test functions
-49-
Error Code Error Contents Meaning Main Causes
Indoor unit outlet pipe Indoor unit outlet pipe temperature

06 Refer to CH02
temperature sensor error sensor open or short
Basic Part
1. Indoor units are in different mode
The Indoor units started later are
All Indoor units are not running in 2. PCB fault
07 operated in different mode from
same mode 3. Wrong setting of wired remote
earlier one.
controller or remote controller fault*
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
*** Dissolution method CH07 with remote controller

Test functions
1) Error removal method : Turn off remote controller by pressing the On/Off button on the cabled remote controller.
The error code will be removed automatically after a few seconds.
With cableless remote controller: Turn off indoor unit, and turn on with the other operation
mode the error will disappeared
2) Immediately change the operation mode after the pressing the On/Off button .
The same operation mode as in the indoor unit started at first other than the defective unit mode (heating /cooling)
**** After replacing the indoor unit PCB, it should be done to do Auto addressing and input the address of central control
-50-
Problem in EEPROM inside 1.Error developed in transmission between the micro-

Indoor unit EEPROM processor and the EEPROM on the surface of the PCB.
09 Indoor PCB ASS’Y 내
error
EEPROM 2.ERROR due to the EEPROM damage
Basic Part
- Replace the indoor unit PCB, and then make sure to do Auto addressing and input the address of central control
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-51-
1. Motor connector connection fault

Indoor unit BLDC fan motor Indoor BLDC fan motor feedback
10 2. Indoor PCB fault
failure signal is absent (for 50 sec.)
3. Motor fault
Basic Part
Is connector No
Connect properly
connection proper?
Yes
Troubleshooting
Guide for each
Is fan motor No
Error Code
Replace indoor unit fan motor
normal?*
Yes
Replace indoor unit PCB **
Component Check
Electrical
* It is normal when check hall sensor of indoor fan motor as shown below
hundreds kΩ hundreds kΩ
hundreds kΩ hundreds kΩ
Solution Check
<Checking connection state of fan motor connector>

Test functions
** Replace the indoor unit PCB, and then make sure to do Auto addressing and input the address of central control
(Notice: The connection of motor connector to PCB should be done under no power supplying to PCB)
-52-
Indoor unit doesn’t get signal

Indoor unit 1. Indoor 485 transmission PCB fault
11 from ODU for 3 minutes
transmission error 2. After PCB replacing, auto addressing was not done
continuously
Basic Part
After ODU main PCB No No

After Auto addressing, Replace indoor unit 485
reset, error code
error code disappears? transmission PCB
disappears?
Yes Yes
Troubleshooting
Guide for each
Error Code
END
Component Check
Electrical
Solution Check
Test functions
-53-
- Compressor checking
Basic Part
Troubleshooting
Guide for each
Error Code
*table #1
Component Check
Electrical
Solution Check
*table #1
Test functions
Multi B Plus II / Sync II / Multi V MINI Multi V MINI

Multi V Plus/Sync
Water II (1Φ) (3Φ)
U-V : 1.16Ω ± 7% U-V : 1.083Ω± 10%

Inverter
1.2Ω ± 10% V-W : 1.19Ω ± 7% 0.188Ω ± 10% V-W : 1.123Ω ±10%
Compressor
U-W : 1.21Ω ± 7% U-W : 1.096Ω ±10%
U-V : 1.96Ω ± 10%

Const Speed
V-W : 1.91Ω ± 10% -
Compressor
U-W : 1.99Ω ± 10%
-54-
Error Code
Plus II, Sync II :
Plus :
-55-
- Fan checking
- EEV
Basic Part
Troubleshooting
Guide for each
Error Code
<EEV wiring (Outdoor unit)>
Component Check
Electrical
Outdoor unit main LEV Outdoor unit sub cooling LEV Indoor unit LEV
Solution Check
① - ③ : around 300Ω ① - ③ : 104 ± 6Ω ① - ③ : around 300Ω
② - ④ : around 300Ω ② - ④ : 104 ± 6Ω ② - ④ : around 300Ω
① - ⑤ or ③ - ⑤ : around 150Ω ① - ⑥ or ② - ⑥ or ① - ⑤ or ③ - ⑤ : around 150Ω

Test functions
④ - ⑥ : around 150Ω ③ - ⑥ or ④ - ⑥ : 52 ± 3Ω ④ - ⑥ : around 150Ω
-56-
Error Code
PCB connector
-57-
* : For this checking, you should make LED circuit by yourself
- EEV
*
Error Code
-58-
- Phase Bridge Diode
Error Code
-59-
- Inverter Compressor’s IPM
Error Code
<2 fan system(UW, UW1 chassis)>
-60-
- Fan IPM
Error Code
<1 fan UY chassis)>
-61-
- Fan IPM
Error Code
-62-
- Capacitors and resistor
Error Code
- Replacement procedure of the compressor(Plus II)
-63-
Error Code
- Replacement procedure of the compressor(Plus II)
-64-
Plus :21
1. Over current detection at the inverter
Plus II:
compressor (U,V.W)
211,212,213,214
2. IPM overheating.
3. Insulation damage of the compressor
S IPM fault of inverter Defective inverter compressor,
N1 Right / compressor motor damage
Basic Part
Inverter element (IPM) defect
P 21 Comp. compressor 4. Low input voltage at the outdoor
A 5. Inverter compressor terminal disconnected
C or loose.
E N2 Left
6. Inverter PCB / IPM PCB defect
21 Comp.
Error diagnosis and countermeasure flow chart(Plus II)
Troubleshooting
(U-V : 1.16Ω ± 7% / V-W : 1.19Ω ± 7% /U-W : 1.21Ω ± 7%)
Guide for each

Error Code
Component Check
Electrical
Solution Check
Test functions
-65-
Point Checking
INV Plus - Deviation between phases should be less than 2A.

Comp.
Running
Current
Basic Part
(COMP
start)
U phase V phase W phase

Plus II
Troubleshooting
Guide for each
Error Code
Coil resistance INV, const. speed comp. resistance :INV COMP → 1.2Ω±10%(Plus/Sync),
(No power) U-V: 1.16±7%Ω, V-W: 1.19±7%Ω, W-U: 1.21±7%Ω(plus II/SyncII/Space II) MINI model : see page 00
Constant speed COMP : (U-V)1.96Ω/(V-W)1.91Ω/(U-W)1.99Ω±10%)
Component Check
Electrical
U-W phases resistance V-W phase resistance U-V phase resistance
Insulation
resistance Insulation resistance : INV COMP → above 2㏁, const. comp : above ㏁
(No power)
Solution Check
Compressor
connector
Test functions
Comp. connector Comp. conector Cooling fan connector Cooling fan operation
(Plus II)
IPM bolt connecting
-66-
Part Check
(Function) points
INV 2. Power & 3. High pressure 4. DC-Link 6. transmission 5. Checking circuit
COMP start-relay switch & sensing & circuit to main for reverse phase
PCB drive circuit power-relay display circuit PCB of input power
Basic Part
drive circuit
(INV
COMP
part)
(plus)
7. On-board
writing
connector
Troubleshooting
1. MICOM
Guide for each

circuit
Error Code
8. CT sensing
circuit
9. PWM driving
signal output
circuit
Component Check
Phenomena Check point How to check? Counter-measure
Electrical
No power 2.Power -Input voltage should be 220V. - Check & replace fuse(3.15A),
at PCB (when power is supplied) T-N voltage (220V)
-Input resistance should be more than a few ㏀ - If resistance value is
(when power is not supplied) 0~100Ω ,
replace PCB
No transmission 6.Transmiss -Yellow LED should blink. - Check yellow LED blinks or
ion circuit not
to main - When is OFF, check
PCB transmission
Solution Check
with main PCB and replace
Malfunction of 9.PWM --Green LED should blink. - Replace PCB

inverter compressor signal -Check IC port coupler
cable of PWM drive
(when power is
not supplied)
Test functions
1-2 Diode : 1.0V 2-3 Diode : 1.4V
Inverter compressor Red LED -When red LED blinks. -Check error code displayed at
PCB Error Error displays about inverter compressor PCB main PCB
-67-
Part
Check point
(Function)
IPM Check voltage &

resistance of
Basic Part
each phases
(CH21 (When power
CH22) is not supplied)
(Plus)
P-U :DIODE(0.4V) P-V :DIODE(0.4V) P-W :DIODE(0.4V)

resistance(a few ㏁) resistance(a few ㏁) resistance(a few ㏁)
Troubleshooting
Guide for each
Error Code
N-U :DIODE(0.4V) N-V :DIODE(0.4V) N-W :DIODE(0.4V)
Component Check
Sub PCB
Electrical
Check the IPM terminal connecting condition
Solution Check
Heat sink
cooling fan
(Plus)
Test functions
Position of cooling fan Heat sink cooling fan

drive connector in main PCB
-68-
Part Check
(Function) How to check? Counter-measure
points
Capacitor Electric capacity. -Electricity capacity of capacitor must be - Replace capacitor

(To charge DC (when power is 2600~2800㎌ and the resistance of capacitors when value is more or
voltage for not supplied) should be more than a few ㏀ less than normal spec.
Basic Part
inverter
compressor)
(Plus)
* Check values at both

terminal of capacitor
Troubleshooting
Guide for each
DC charging - Charged voltage of between terminals of capacitor - Check input voltage
Error Code
voltage (= between IPM P-N terminal = DC link terminals) and
(When power is should be more than 450V replace capacitor
supplied) (At the moment of inverter compressor start)
Magnet Magnet switch -When check resistance of 1st coil of magnet switch, -In case resistance is
Switch 1st coil resistance should be 0.47 ㏀ ∞ or 0 Ω,
(When power is not supplied)  Replace Magnet
(Plus) switch
-When magnet switch is on, voltage should be 220V
Component Check
(When power is not supplied) -When voltage is not
220V, magnet switch
Electrical
is melt down
- Replace magnet
switch
Solution Check
** check point of 1st coil of magnet switch
Magnet switch - While pressing green button of magnet switch, -Replace magnet
connection Voltage of each connectors should be 0V or switch
check Resistance should be 0~1Ω
(In case power (Warning: power should not be supplied)
is not supplied)
Test functions
-69-
Part Check
(Function) points
INV 1. Power &

start-relay 5. Port from 6. Port from
COMP 2.220V
3. P port 4. N port Diode Reactor
drive circuit connector
PCB
Basic Part
(INV
COMP
part)
(Plus II)
U terminal
Troubleshooting
Guide for each
7. On-board
Error Code
V terminal writing connector
8. CT sensing circuit
9.Power relay
W terminal
10.Comm port
& LED
12. PWM LED 11. PWM driving signal output circuit
Component Check
Electrical
No power 2.Power -Input voltage should be 220V. -T-N voltage (220V)
at PCB (when power is supplied)
-Input resistance should be more than a few ㏀ - If resistance value is
(when power is not supplied) 0~100Ω ,
replace PCB
Solution Check
No transmission 10.Transmi -LEDs should blink. - Check LED blinks or not
(Fan, Main PCB) ssion circuit - When is OFF, check
to main, transmission
fan PCB with main, fan PCB
Test functions
Inverter compressor 12. PWM -When red LED is on. -Check error code displayed at
PCB Error LED PWM is normal main PCB
-70-
Part
Check point
(Function)
IPM Check voltage

& resistance of
Basic Part
each phases
(CH21, (When power
- - -
CH22) is not supplied) + + +
(Plus II) P-U :28kΩ±10% P-V :28kΩ±10% P-W : 28kΩ±10%
Reverse: P-U :Open P-V :Open P-W : Open
+ + +
Troubleshooting
Guide for each
Error Code
- - -
N-U :28kΩ±10% N-V :28kΩ±10% N-W : 28kΩ±10%

Reverse: N-U :Open N-V :Open N-W : Open
Check power
Heat sink supplay and
cooling fan operation
status
Component Check
(Plus II)
Electrical
Position of cooling fan Heat sink cooling fan
drive connector in main PCB
(220V output)
Solution Check
Test functions
-71-
Part Check
How to check? Counter-measure
(Function) points
Capacitor DC charging - Charged voltage of between terminals of capacitor - Check input voltage
(To charge DC voltage (= between IPM P-N terminal = DC link terminals) and replace capacitor
voltage for (When power is should be more than 450V
Basic Part
inverter supplied) (At the moment of inverter compressor start)
compressor)
(Plus II)
Troubleshooting
Guide for each

Error Code
Magnet Magnet switch When magnet switch is on, output voltage should be When output voltage is
Switch 380V (Running) not 380V, Replace PCB
(Plus II)
Component Check
Electrical
Solution Check
Test functions
-72-
Plus:22 1. Compressor damage

Plus II: 2. Current sensing sensor (CT) damage
221,222,223,224 3. Low input voltage
The current flowing at the CT 4. compressor terminal is disconnected or loose
Over current of
N1 Right sensing circuit is more than the 5. Abnormality at the outdoor / indoor unit fan
Basic Part
S inverter
22 Comp. allowable maximum value of the 6. Cover or clogging
P compressor
A current (Outdoor unit covering during cooling mode
C / Filter clogged at the indoor during heating
N2 Left
E mode )
22 Comp.
7. Defective inverter PCB/IPM PCB
Error diagnosis and countermeasure flow chart (Plus II)
Troubleshooting
Guide for each
Error Code
(U-V : 1.16Ω ± 7% / V-W : 1.19Ω ± 7% /U-W : 1.21Ω ± 7%)
Component Check
Electrical
Solution Check
Test functions
-73-
Part Check
(Function) points How to check? Counter-measure
T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within Standard±10% -Check supply power
(Terminal - Voltage of 1φ(R-N,S-N,T-N) should be within and connection
Block, Input 220V±10%. condition
Basic Part
power) - Voltage fluctuation should be within 10V
- While stand-by and in operation,
Voltage drop should be within 10V
Troubleshooting
Guide for each
Checking points of 3φ(R-S) Checking points of 1φ(R-N)
Error Code
Check Ω - Resistance of R-S,S-T,R-T,R-N,S-N should be -Check short or not of
(In case power more than a few ㏀ Control box (Noise filter,
is not supplied) PCB, cables)
- Resistance of T-N should be within 40~50Ω - Replace transformer
(Main transformer of outdoor)
FUSE Check - Voltage of fuse should be within 0~1V -In case of 220V,
(Protect over- disconnection of Fuse is disconnected.
loaded FUSE  Replace FUSE
current) (when power is
supplied)
Component Check
(plus)
Electrical
Checking points of R φ fuse
Check - Resistance of fuse should be within 0~1Ω -In case resistance is ∞,
disconnection of Fuse is disconnected.
FUSE  Replace FUSE
(when power is
not supplied)
Nose filter Check voltage -Voltage of each connector (R-R,S-S,T-T) should - In case of 220V
(Noise emit & (When power is be within 0~40V It is disconnected
protect) supplied)  Replace noise filter
Solution Check
(Plus) (Plus II)
Test functions
Checking points of Voltage
Check Ω -Resistance of each connectors (R-R,S-S,T-T) -In case resistance is

(In case power should be within 0~10Ω ∞, noise filter is
Is not supplied) disconnected.
 Replace noise filter
-74-
Part Check
(Function) points
INV PCB
(Plus) * Measure the CT current with clamp meter -Multi V SPACE : U(+), U(-), V(+), V(-)
The current difference among
* Multi V PLUS
- Multi / Sync
V PLUS / Sync : R phase phases is less than 0.5A ±10%
Basic Part
Troubleshooting
Guide for each
Error Code
U(+) U(-) V(+) V(-)
Component Check
Electrical
3φ DIODE
(Plus)
P-U :DIODE(0.4V) P-V :DIODE(0.4V) P-W :DIODE(0.4V) Solution Check

Test functions

-75-
Part Check
(Function) points
INV PCB
* Measure the CT current with clamp meter
(Plus II)
*Current < 25A
Basic Part
Troubleshooting
Guide for each
Error Code
3φ DIODE
Component Check
(Plus II)
Electrical
Solution Check
Test functions
-In case the measured value is different from the table, set multi tester to resistance mode
and measure. If the value is small (0 Ω) or high (hundreds M Ω), PCB needs to be
replaced.
- In case that bridge diode is damaged, check if inverter PCB assembly(IPM) is needed to be
replaced.
-76-
23(plus)
23(1~4,Plus II) 1. Looseness of DC link terminal
S N1 Right DC voltage charging for 2. Damage in starting relay
Problem in DC charging voltage
P 23 Comp. inverter compressor driving 3. Capacitor damage
after starting relay turned on
Basic Part
A defect 4. Defective sensing circuit of the
C N2 Left inverter PCB
E 23 Comp.
Troubleshooting
Guide for each
Error Code
* After indoor unit turned on and the compressor is not operated,
Component Check
just before magnetic switch is turned on
the voltage between the 2 terminal as below is more than 270V
Electrical
Plus / Sync Plus II
Solution Check
Part Check
(Function) points
Capacitor Electric -Electricity capacity of capacitor must be -Replace capacitor

(To charge DC capacity. 2600~2800㎌ and the resistance of capacitors when value is more or
voltage for (when power is should be more than a few ㏀ less than normal spec.
inverter not supplied)
compressor)
Test functions

DC charging - Charged voltage of between terminals of capacitor - Check input voltage

voltage (= between IPM P-N terminal = DC link terminals) and replace capacitor
(When power is should be more than 450V
supplied) (At the moment of inverter compressor start)
-77-
Part Check
(Function) points
T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within 380±10% -Check supply power and
(Terminal - Voltage of 1φ(R-N,S-N,T-N) should be within connection condition
Block, Input 220±10%.
power)
Basic Part
- Voltage fluctuation should be within 10V
Voltage drop should be within 10V.
Troubleshooting
Guide for each
Error Code
FUSE Check -Voltage of fuse should be within 0~1V -In case of 220V,
(plus) supplied)
Component Check
Electrical
Check -Resistance of fuse should be within 0~1Ω -In case resistance is ∞,

(when power is
not supplied)
Nose filter Check voltage -Voltage (R-R,S-S,T-T) < 0~10V - In case of 220V
(Noise emit & (When power is  If voltage is higer than 10~40V, check resistance It is disconnected
Solution Check
protect) Supplied) (Plus) (Plus II)  Replace noise filter
Test functions
Checking points of Voltage

-78-
24(Plus Main) 1. High pressure switch defect

24(1~4,Plus II) 2. Fan defect of indoor unit or outdoor unit
3. Check valve of compressor clogged
S N1 Right 4. Pipe distortion due to the pipe damage
P 24 Comp. 5. Refrigerant overcharge
Basic Part
A Excessive rise of Compressor off due to 6. LEV defect at the indoor or outdoor unit .
C N2 Left discharge pressure in the high pressure 7. Covering or clogging
E 24 Comp. outdoor compressor switch in outdoor unit (Outdoor covering during the cooling mode /
Indoor unit filter clogging during the heating mode)
(plus) 8. SVC valve clogging
109 (Sub1) 9. Outdoor PCB defect
140 (Sub2) 10. HR unit valve coil defect(Multi V Sync)
154 (Sub3) 11. HR unit PCB defect(Multi V Sync)
Troubleshooting
Guide for each
Error Code
Is high pressure switch
No
connector connected Connect securely
to PCB?*
Yes
Is high pressure switch No No

Is high pressure switch
connector short Replace high pressure switch
terminal short?***
during off time?**
Yes
Yes
Component Check
Replace connecting cable
Electrical
No
Is SVC valve open? Open SVC valve
Yes
Is this error appeared No Re-check momentary

again after reset? problem or not
Yes
Is high pressure Replace PCB Solution Check

No
more than 2500kPa CH24 : inverter compressor PCB
at manifold gauge? CH109~154 : sub unit PCB
Yes
Is high pressure of No
LGMV similar as Replace high pressure sensor
at manifold gauge?
Yes
Test functions
Is it No Check pipe is blocked or

Multi V Sync ? not and take measure
Yes
Next page
-79-
Is it Multi V Sync?
Yes
Basic Part
Is HR unit valve No
Connect HR unit valve connector
connector normal ?
Yes
Is HR unit configuration No Check HR unit manual pipe address

on auto pipe detection? - Refer to HR unit manual pipe detection
Troubleshooting
Guide for each
Yes
Error Code
Is the pipe detection No Set HR unit manual pipe detection
success during auto
- Refer to HR unit manual pipe detection
pipe detection?
Yes
Is HR unit valve LED turns on

No
Component Check
when connected indoor unit Replace HR unit PCB
start to operate?
Electrical
Yes
Is the resistance value of No

Replace HR unit valve coil
HR unit valve coil normal?****
Yes
Is the HR unit PCB valve No

measures ~220V in port? Replace HR unit PCB
[electric component part]
Solution Check
Yes
Check HR unit coil

assembly location
Yes
Check for bent or blocked

from connected pipes
Check blocked HR Unit
Test functions
-80-
* Plus : Connector location of high pressure switch at PCB(Refer electrical component part for Multi V Space)
Inverter compressor PCB SUB outdoor unit PCB
Basic Part
Troubleshooting
Guide for each
Error Code
Checking short or not at connector of high Checking short or not at connector of high
pressure switch pressure switch
Component Check
Electrical
**** Check resistance of HR unit valve coil : 1.85 kΩ(±10%)
- HR unit PCB-
Solution Check
Test functions
-81-
* Plus II: Connector location of high pressure switch at PCB(Refer electrical component part for Mult V Space)
Constant compressor pressure switch Inverter compressor pressire switch
Basic Part
Troubleshooting
Guide for each
Error Code
** Checking short or not at connector of high *** Checking short or not at connector of high
pressure switch pressure switch
Component Check
Electrical
Solution Check
Test functions
-82-
Plus:
25(Main)
147 (Sub1)
The power supply input voltage
149 (Sub2) Low / over voltage 1. Input voltage is abnormal(T-N)
tolerance is more or less than
171 (Sub3) of main PCB input 2. Outdoor unit main PCB defect
Basic Part
allowable standard
Plus I:,
251,252,253,
254
Is input voltage of main No Check input power from building

PCB (T-N) 190V~250V ?* is supplied correctly or not
Troubleshooting
Guide for each
Error Code
Yes
Replace main PCB
Component Check
Electrical
* Check voltage at outdoor T/Block(220V)
Solution Check
Test functions
* Check voltage at outdoor T/Block(220V), Plus II
-83-
Plus II:
261,262,
263,264 1. U,V상 connect orCOMP fault
At below min.Hz, 2. DC CT sensor fault
Basic Part
S N1 Right Compressor start failure
P 26 Comp. U,V current is lower than 1A 3. INV PCB fault
A 4. IPM component or connector fault
C N2 Left
E 26 Comp.
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
• Measure the CT current with clamp meter Solution Check
: U(+), U(-), V(+), V(-)
- The current difference among phases is less
than 0.5A ±10%
Test functions
U(+)U(-)V(+)V(-)
Multi V Space Multi V Plus II
-84-
Error Code
-85-
Basic Part
Troubleshooting
Guide for each
Error Code
(U-V : 1.16Ω ± 7% / V-W : 1.19Ω ± 7% /U-W : 1.21Ω ± 7%)
Component Check
Electrical
Solution Check
Test functions
-86-
Error Code
-87-
32 (Plus Inv) 1. Temperature sensor defect of inverter

Plus II : Over-increase discharge Compressor is off compressor discharge pipe
321,322, temperature of inverter because of over-increase 2. Refrigerant shortage / leak
323,324 compressor at main outdoor discharge temperature of 3. LEV defect
unit inverter compressor 4. Liquid injection valve defect
Basic Part
Right
SPACE 5. Check solenoid valve defect(Sync)
Comp.(N1)
33 (Plus Main)
Plus II :
331,332,
333,334 Compressor is off 1. Temperature sensor defect of constant
Over-increase discharge
because of over-increase (Space:Inv.) compressor discharge pipe?
temperature of constant
Left discharge temperature of 2. Refrigerant shortage/leak
SPACE (Space:Inv.) compressor at
Comp.(N2) constant (Space:Inv.) 3. LEV defect
main constant outdoor and
compressor at main and 4. Liquid injection valve defect
plus sub constant outdoor unit
sub outdoor unit 5. Check solenoid valve defect(Sync)
100,101(Sub1)
Troubleshooting
Guide for each
102,103(Sub2)
Error Code
152,153(Sub3)
Is the additional ref. No

amount correct? Adjust refrigerant amount
[Start up process]
Yes
Component Check
Is there pipe crack No
or trace of leakage?
Electrical
Yes
Is the resistance of discharge No Replace discharge

temperature sensor normal?* temperature sensor
Weld / reconnect the Yes

cracked portion and
recharge refrigerant
Is LEV in outdoor unit normal No
Solution Check
at heating operation? Replace outdoor unit LEV
[refer electric component part]
Yes
Does liquid injection No

Check liquid injection
corresponded
corresponded
operate normally?
Yes
Check another
No No components
Is it cooling mode of Is there pipe
and operation
Multi V Sync ? (strainer etc.) clogging?
Test functions
conditions
Yes / Take measures
Yes
Next page Repair pipe clogging
* Resistance value of discharge temperature sensor

10℃ = 362㏀, 25℃= 200㏀, 50℃= 82㏀, 100℃= 18.5㏀
-88-
Is it cooling mode of No
Multi V Sync ?
Yes
Basic Part
outdoor unit Check sol valve Replace HR unit valve coil
normal?**
Yes
Is the outdoor unit No

check sol valve measure ~220V? Replace outdoor unit PCB
Troubleshooting
Guide for each
Error Code
Yes
Check for bent or blocked pipe
* Error is generated if the resistance is more than 5MΩ (open) and less than 2 ㏀ (short)
Note: Standard values of resistance of sensors at different temperatures (±5% variation)
Component Check
10℃ = 362㏀ : 25℃= 200㏀ : 50℃= 82㏀ : 100℃= 18.5㏀
Electrical
Solution Check
Check the resistance
of constant compressor
discharge temperature
sensor
Test functions

inverter compressor
Check the resistance discharge temperature
of constant compressor sensor
sensor
-89-
Check
Check points
Loc.
Check outdoor
unit LEV
Basic Part
① - ③ : around 300Ω ② - ④ : around 300Ω ① - ⑤ : around 150Ω
Troubleshooting
Guide for each
Error Code
③ - ⑤ : around 300Ω ② - ⑥ : around 300Ω ④ - ⑥ : around 150Ω
Hot gas by pass

Valve
Component Check
Connector
Electrical
resistance
1.85 kΩ(±10%)
Solution Check
Liquid by pass
valve
Connector
resistance
1.85 kΩ(±10%)
Test functions
-90-
Check
Check points
Loc.
Hot gas by pass

Valve
Basic Part
Connector
resistance
1.85 kΩ(±10%)
Troubleshooting
Guide for each
Error Code
Liquid by pass
valve
Connector
resistance
1.85 kΩ(±10%)
Component Check
Electrical
Solution Check
Test functions
-91-
* Calculation of additional refrigerant amount
R410A Multi V Plus, Plus II & Space R410A Multi V Sync
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
for all Multi V system
Solution Check
Test functions
-92-
* R410A Correction Factor(CF)
Basic Part
Multi V
Plus,
Plus II
Troubleshooting
Guide for each
Error Code
Multi V
Space
Multi V
Component Check
Sync II,
Electrical
Sync
Heat Pump / Sync
Solution Check
HP 10 20 30 40 50 60
Multi V
Product Charge (kg) 7.3 8.8 16.1 17.6 24.9 26.4
Water II
CF (kg) 0 0 0 0 0 0
Cooling only / Heat Pump
HP 4 5 6
Multi V
MINI Product Charge (kg) 3.7 3.7 3.7
Test functions
CF (kg) -0.5 0 0
-93-
R22 Multi V Plus
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
* R22 Correction Factor(CF)
HP 5 6 8 10 12 14 16 18 20
Heat Product(kg) 4 4.5 10 10 10 10 20 20 20

Pump CF(kg) 0 0 -3 -2 -1 -1 -2 -2 -2
6(380V)
Product(kg) 4 4.5 10 10 10 20 20 20
Cool 10(220V)
Solution Check
Only 0(380V)
CF(kg) 0 0 -2 -1 -1 -2 -2 -2
-3(220V)
HP 22 24 26 28 30 32 34 36 38 40
30(50Hz)
Product(kg) 20 20 30 30 30 30 30 30 30
Heat 20(60Hz)
Pump 0(50Hz)
CF(kg) -2 -2 0 0 0 1 1 2 2
Test functions
-1(60Hz)
30(50Hz)
Product(kg) 20 20 30 30 30 30 30 30 30
Cool 20(60Hz)
Only 0(50Hz)
CF(kg) -2 -2 0 0 0 1 1 2 2
-1(60Hz)
-94-
-Plus, Sync Error happens because of 3 1. High pressure sensor defect

34 times successive 2. Indoor or outdoor unit fan defect
Over-increase of
(Main) compressor off due to over- 3. Deformation because of damage of refrigerant pipe
discharge pressure of
143 increase of high pressure 4. Over-charged refrigerant
compressor
Basic Part
(Sub1) by high pressure sensor 5. Indoor / outdoor unit LEV defect
145 7. When blocked
(Sub2) - Outdoor unit is blocked during cooling
169 Error happens because of 3 - Indoor unit filter is blocked during heating
Over-increase of water
(Sub3) times successive 8. SVC valve is clogged
temperature
Plus II: compressor off due to over- 9. PCB defect of outdoor unit
(Multi V Water)
341,342, increase of water 10. Indoor unit pipe temperature sensor defect
343,344 temperature 11. Insufficient water flow rate. (Multi V Water)
Troubleshooting
Guide for each
No
Error Code
Is service valve opened ? Open service valve
Yes
Are transmission No Check and repair transmission

cable / pipe connection
cable / pipe connection
normal?
Yes
Component Check
[Start up process]
Electrical
Yes
Is fan normal?
No Replace related parts
(Indoor fan during heating
(Refer to Error 105~108)
Outdoor fan during cooling)
Yes
Is filter blocked
(Heating:indoor, No Clean indoor filter (heating)
Solution Check
Cooling:outdoor /outdoor heat exchanger (cooling)?
heat exchanger)?
Yes
Is value of high pressure No

sensor same as Manifold Replace sensor of high pressure
value(Is it high actually)?
Yes
Check indoor unit LEV

Test functions
Is it Multi V Sync No Check indoor unit PCB

Or Multi V Water ? Check in/outdoor installation
condition
Yes
Next page
-95-
Is it Multi V Sync?
Yes
Basic Part
No is the resistance value No
Is it heating mode ? of outdoor unit Replace HR unit valve coil
check sol valve normal?*
Yes
Yes
is the outdoor unit No

Check sol valve Replace outdoor unit PCB
measure ~220V in port?
Yes
Troubleshooting
Guide for each
Error Code
Is HR unit valve No
Replace HR unit valve connector
connector normal ?
Yes

Yes
Component Check
Electrical
Is the pipe detection No Set HR unit manual pipe detection
success during auto
pipe detection?
Yes
Is HR unit valve LED turns on

No
start to operate?
Solution Check
Yes

HR unit valve coil normal?*
Yes

Yes
Test functions
Check HR unit coil

assembly location
Yes
Check for bent or blocked

[1] Check sol valve coil resistance value : 1.85 kΩ(±10%)
Check blocked HR Unit HR unit valve coil resistance value : 1.85 kΩ(±10%)
-96-
Error Code
Check water flow rate
-97-
No
Is water flowrate normal?
Is it Multi V Water?
END
Yes
Error No. Error Contents Meaning Main Causes
1. Low pressure sensor defect

2. Outdoor/indoor unit fan defect
-Plus, Sync 3. Refrigerant shortage/leakage
35 (Main) 4. Deformation because of damage of refrigerant pipe
Error happens because
144 (Sub1) 5. Indoor / outdoor unit LEV defect
Basic Part
of 3 times successive
146 (Sub2) Excessive drop of 6. Covering / clogging
compressor off due to
170 (Sub3) discharge pressure of (outdoor unit covering during the cooling mode/
excessive drop of low
compressor indoor unit filter clogging during heating mode)
pressure by the low
-Plus II: 7. SVC valve clogging
pressure sensor
351,352, 8. Outdoor unit PCB defect
353,354 9. Indoor unit pipe sensor defect
10. HR unit valve coil defect(Multi V Sync)
11. HR unit PCB defect(Multi V Sync)
Troubleshooting
Guide for each
No
Error Code
Is service valve
Open service valve
opened?
Yes
No
Are transmission cable/ check transmission/
piping normal? piping correction.
Yes
Component Check
[Start up process]
Electrical
Yes
Is there pipe crack No

or trace of leakage?
Yes
Is fan normal? No Check and replace related parts
(in heating outdoor fan,
Weld / reconnect the (error 105~108 reference)
in cooling indoor fan)
cracked portion and
recharge refrigerant Yes
Solution Check
No
Is strainer Ok?* Replace the strainer
Yes
Are the values of manifold

and low pressure sensor same? No
Replace the pressure sensor
( Is the low pressure value
actually low?)
Yes
Test functions
No Check indoor unit LEV

Is it Multi V Sync? Check indoor unit PCB
Check in/outdoor installation condition
Yes
Next page
-98-
Is it Multi V Sync?
Yes
Basic Part
No is the resistance value No
Is it heating mode? of outdoor unit Replace HR unit valve coil
check sol valve normal?**
Yes Yes
is the outdoor unit No

Check sol valve Replace outdoor unit PCB
measure ~220V in port?
Yes
Troubleshooting
Guide for each
Error Code
No
Is HR unit valve
Replace HR unit valve connector
connector normal ?
Yes

Component Check
Yes
Electrical
Is the pipe detection No
set HR unit manual pipe search address
success during auto
pipe detection?
Yes
Is HR unit valve LED turns on No

start to operate?
Solution Check
Yes
No
Is the resistance value of
HR unit valve coil normal?**
Yes

Yes
Test functions
Check HR unit coil * In case of frost and high temperature difference between inlet and
assembly location outlet of strainer, strainer blocking may happen
(Caution: frost on the outlet area (afterward after half of body)
Yes
Check for bent or blocked ** Check sol valve coil resistance value : 1.85 kΩ(±10%)
Check blocked HR Unit HR unit valve coil resistance value : 1.85 kΩ(±10%)
-99-
Error code Error contents Meaning Main causes
Plus:40
Plus II:
401,402,403,404 1. Fuse failure
Low current at CT While inverter compressor 2. Defective noise filter
SP N1 Right or operation R phase current 3. R phase connection problem
Basic Part
A 40 Comp. CT sensor defect drops below 1A or CT short 4. CT sensor failure (inverter PCB
C failure)
N2 Left
E
40 Comp.
Troubleshooting
Is the fuse normal? No
Guide for each

Replace the fuse
Error Code
Yes
Is noise filter normal? No

Replace noise filter
Yes
Component Check
After reset and restart the No
Electrical
system, is CT value actually
less than 1A?* Replace Inverter PCB
-Plus/Sync : R phase
-Space : U, V phase
Yes
Check connection state of

R phase cable and reconnect
Solution Check
* Measure the CT current with clamp meter -Multi V SPACE : U(+), U(-), V(+), V(-)
The current difference among
- Multi V PLUS / Sync : R phase phases is less than 0.5A ±10%
Test functions
U(+) U(-) V(+) V(-)
-100-
supplied)
(plus)
Basic Part

(when power is
not supplied)
Troubleshooting
Guide for each
Error Code
(Noise emit & (when power is be within 0~40V It is disconnected
protect) Supplied)  Replace noise filter
(Plus) (Plus II)
Component Check
Electrical
Solution Check
(When power should be within 0~10Ω ∞, noise filter is
Test functions
-101-
Plus:41 (Main inverter compressor)

Plus II:411,412,413,414
SPACE Right Comp.(N1)
Basic Part
Plus:
47 (Main constant compressor) 1. Connection of the compressor defect
Compressor
121 (Sub1 constant compressor 1) Sensor measurement discharge pipe temperature sensor
discharge pipe
122 (Sub1 constant compressor 2) valve is abnormal 2. Discharge pipe compressor sensor
temperature
133 (Sub2 constant compressor 1) (Open/Short) of the compressor (open/short) defect
sensor error
134 (Sub2 constant compressor 2) 3. Outdoor PCB defect
162 (Sub3 constant compressor 1)
163 (Sub3 constant compressor 2)
Plus II:
471,472,473,474
(Constant compress)
Troubleshooting
Guide for each
Error Code
Sensor connection to PCB No

Insert sensor connector to PCB properly
is normal?
Yes
Is the resistance of No
Replace sensor
Component Check
sensor normal?*
Electrical
Yes
Is sensor resistance No
value same as temperature Replace corresponding outdoor PCB
value of LGMV?
Yes
Replace corresponding sensor
Solution Check
* Error is generated if the resistance is more than 5MΩ (open) and less than 2 ㏀ (short)
Note: Standard values of resistance of sensors at different temperatures (±5% variation)

10℃ = 362㏀ : 25℃= 200㏀ : 50℃= 82㏀ : 100℃= 18.5㏀
Test functions
Check the resistance Check the resistance

inverter compressor of constant
discharge compressor
temperature sensor discharge
temperature sensor
-102-
Basic Part
Check the resistance inverter
compressor discharge
temperature sensor
of constant compressor
Troubleshooting
Guide for each

sensor
Error Code
Component Check
Electrical
Solution Check
Test functions
-103-
Plus:
42 (Main)
117 (Sub1)
Abnormal value of 1. Bad connection of low pressure connector
129 (Sub2) Sensor error of low
sensor 2. Low pressure connector defect (Open/Short)
158 (Sub3) pressure
Basic Part
(Open/Short) 3. Outdoor PCB defect
Plus II:
421,422,423,42
4
Plus:
43 (Main)
116 (Sub1)
Abnormal value of 1. Bad connection of high pressure connector
128 (Sub2) Sensor error of high
sensor 2. High pressure connector defect(Open/Short)
157 (Sub3) pressure
(Open/Short) 3. Outdoor PCB defect
Troubleshooting
Plus II:
Guide for each

431,432,433,43
Error Code
4
Is sensor connected No
Connect sensor to PCB correctly
to PCB correctly?
Yes
After replacement of No
Replace corresponding
Component Check
outdoor unit main PCB
pressure sensor
is the system normal?
Electrical
Yes
END
High pressure
sensor
Solution Check
Low pressure
sensor
Pressure sensor
connection
Plus model on main PCB
Test functions
Plus II model
-104-
Plus:
44 (Main)
1. Bad connection of air temperature
118 (Sub1)
connector
130 (Sub2) Sensor error of outdoor air Abnormal value of
2. Air temperature connector
159 (Sub3) temperature sensor (Open/Short)
Basic Part
defect(Open/Short)
Plus II:
3. Outdoor PCB defect
441,442,
443,444
Plus:
45 (Main H/E A)
48 (Main H/E B)
123 (Sub1 H/E A)
124 (Sub1 H/E B)
135 (Sub2 H/E A) Piping temperature sensor error
connector
136 (Sub2 H/E B) of heat exchanger in Abnormal value of sensor
Troubleshooting
164 (Sub3 H/E A) main & sub outdoor unit heat (Open/Short)
Guide for each

defect(Open/Short)
165 (Sub3 H/E B) exchanger (A,B)
Error Code
Plus II:
451,452,
453,453(H/E A)
481,482,
483,484(H/E B)
Plus:
46 (Main)
120 (Sub1)
connector
132 (Sub2) Compressor suction Abnormal value of
161 (Sub3) temperature sensor error sensor (Open/Short)
defect(Open/Short)
Component Check
Plus II:
461,462,
463,464
Electrical
Plus:47
(constant compressor
of main outdoor unit)
Plus II: Discharge piping temperature
471,472,473,474 Abnormal value of sensor
sensor error of constant(Space: Refer to CH41
(Open/Short)
Inv.) compressor (Main unit)
Left
SPACE
Comp.(N2)
Piping temperature sensor error Solution Check

Plus:48 of heat exchanger in main & Abnormal value of sensor
Refer to CH45
(Heat exchanger B) sub outdoor unit heat (Open/Short)
exchanger (B)
Connect sensor to PCB correctly
to PCB correctly??
Yes
Test functions
No
Is sensor value correct?* Replace sensor
Yes * If value is 100 ㏀ ↑(open) or 100 Ω ↓(short), error occurs
NB: Resistance value of temperature sensor change according to temperature

Replace corresponding It is normal if value shown as below (±5% error)
outdoor unit PCB Sensor of air temperature: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Sensor of piping temperature: 10℃ = 10㏀ : 25℃= 5㏀ : 50℃= 1.8㏀
-105-
Basic Part
Measure resistance of outdoor air temperature Measure resistance of outdoor suction pipe
sensor temperature sensor
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Measure resistance of outdoor HEX(A) Measure resistance of outdoor HEX(B)
temperature sensor temperature sensor
Solution Check
Test functions
Plus II model
-106-
(plus)
49 (Main) The measured value of the 1. Abnormal input voltage
Outdoor voltage
148(Sub1) sensor is not 2. Outdoor line fuse damage
sensing error
150(Sub2) normal(Open/Short) 3. Outdoor main PCB defect
172(Sub3)
Basic Part
is the power input normal? No

(3 phase =380V±10%, Check power supply
single phase =220V±10%)
Yes
Troubleshooting
Guide for each
Is the power input to No
Check the fuse and wiring
Error Code
the outdoor PCB
220V±10% ?
Yes
Change main PCB of outdoor
* Check Line Fuse of MAIN PCB(Plus) * Check Line Fuse of MAIN PCB(Plus II)
Component Check
Electrical
Part Check
(Function) points
Solution Check
T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within 380±10% -Check supply power and
(Terminal - Voltage of 1φ(R-N,S-N,T-N) should be within connection condition
Block, Input 220±10%.
power) - Voltage fluctuation should be within 10V
Test functions

-107-
(Plus II) ODU 3phase power 1. Input Voltage abnormal (R,S,T,N)

Omitting one or more of
501,502, omission 2. Check power Line connection condition
R,S,T input power
503,504 error 3. Main PCB damage
Basic Part
Check
No R~S/S~T/T~R phase voltage is 380V ± 10%
Is input voltage normal? R~N/S~N/T~N phase voltage is 220V ± 10%
Check connection condition and wiring if power is
abnormal
Yes
Troubleshooting
Guide for each
No
Is main PCB assembly normal? Replace Main PCB assembly
Error Code
Yes
Recheck power and

installation condition
Component Check
Electrical
Solution Check
Test functions
-108-
1. 130% more than outdoor unit rated capacity

Over-Capacity Sum of indoor unit capacity 2. Wrong connection of transmission cable/piping
Plus:51
(Sum of indoor unit capacity is exceed outdoor unit 3. Control error of sub outdoor unit DIP switch
Plus II:511
more than outdoor capacity) capacity specification 4. Power supply defect of Sub unit PCB
5. Outdoor unit PCB defect
Basic Part
Is capacity sum of
No Are quantity and capacity No Check transmission cables
indoor units less than
of indoor units installed between indoor and outdoor
130% of outdoor unit
same as the data of LGMV? units
capacity at LGMV?
Yes Yes
Troubleshooting
Guide for each
Adjust the capacity of indoor
Error Code
and outdoor unit
Is SUB DIP switch No

5(SUB1), 6(SUB2) Adjust corresponding DIP switch
ON?*
Yes
Is power of SUB PCB No Is main power really supplied? No Supply main

On? (Check LED blinking) (Terminal Block T-N) power again
Component Check
Yes Yes
Check and replace PCB,
Electrical
Line Fuse, Transformer
Is transmission
No
cables between outdoor units Re-connect
connected correctly?**
Yes
Is error code released
Solution Check
No
in order(Sub2 Sub1Main) Replace Main or Sub PCB
after power reset?
Yes
End
Test functions
-109-
* Dip switch setting of SUB unit(Plus)
SUB 1 SUB 2
Basic Part
Troubleshooting
Guide for each
ON
Error Code
ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Sub 1 : SW5 ON Sub 2 : SW6 ON
** In order to check transmission
Component Check
cables between outdoor units,
check in order as below
Electrical
: PCB connectors →
terminal block →
transmission cables
1 1
2 2
Solution Check
3
*** Press the red button for auto-addressing,

Test functions
-110-
* Dip switch setting of SUB unit (Plus II)
SUB1 SUB2
Basic Part
Troubleshooting
Guide for each
Error Code
** In order to check transmission
Component Check
cables between outdoor units,
check in order as below
: PCB connectors →
Electrical
terminal block →
transmission cables
1 1
2 2
Solution Check
3
*** Press the red button for auto-addressing,

Test functions
-111-
Plus:52
Plus II:521,522,
523,524
Main controller can’t 1. Power cable or transmission cable is not connected
S N1 Right Transmission error between receive signal from 2. Defect of outdoor Main fuse/Noise Filter
52 Comp. (Inverter PCB → Main PCB )
Basic Part
P inverter controller 3. Defect of outdoor Main / inverter PCB
A
C N2 Left
E 52 Comp.
Is transmission
LED (Yellow) of inverter No Is noise filter or fuse No
Replace noise filter or fuse
compressor normal?
PCB on?
Troubleshooting
Guide for each
Yes
Yes
Error Code
Replace inverter compressor PCB
No
Is transmission cable
Re-connect transmission cable
connected correctly?
Yes
No
Is MAIN PCB normal? Replace MAIN PCB
Component Check
Yes
Electrical
Replace inverter compressor PCB
* The method of checking MAIN PCB and inverter compressor PCB (If normal, transmission LED blinks)
( Refer electrical component part for Multi V Space)
- Transmission connector & LED in inverter compressor PCB - Transmission connector & LED in MAIN PCB
Solution Check
(Plus) (Plus)
Test functions
(Plus II) (Plus II)
-112-
Plus:53 1. Transmission cables are not connected

Plus II: Transmission error In case Main PCB can’t receive 2. Transmission cables are short or open
531,532, (Indoor unit → Main PCB) signal from indoor unit 3. No addressing after changing indoor unit PCB
533,534 4. Outdoor Main PCB or indoor PCB defect
Basic Part
Are quantity of indoor No Is indoor unit No

units installed same as quantity correct after
the data of LGMV? Auto Addressing?
Yes
Yes
Troubleshooting
Guide for each
Error Code
End
No
Is power supplied
Supply power
to indoor units?
Yes
Component Check
Replace indoor unit PCB or
transmission PCB
after check defected indoor
Electrical
In case of CH53, almost happened with CH05, the indoor units not operated actually are normal so check with same
method of CH05. and additionally check as shown as below and above flow chart
- Although the quantity of indoor units installed is same as LGMV data there may be a few indoor units with which
the number of transmission is not increased with LGMV
Solution Check
- Although the quantity of indoor units installed is not same as LGMV data, and if transmission of the indoor unit
displayed at LGMV is done well then the indoor unit suspected to have some problem (and is not appear at LGMV)
may have following problems
① wrong connection of transmission cable or power cable
② fault of power / PCB / transmission cable
③ duplication of indoor unit number
- If transmission is not doing well wholly then the Auto Addressing is not done
- The case that CH53 appear at indoor unit also Auto Addressing is not done so indoor unit address may be duplicated
*After replacement of indoor unit PCB, Auto Addressing should be done, if central controller is installed then
the central control address also should be input.
in case that only transmission PCB is replaced above process is not needed
Test functions
-113-
Plus:
54 (Main)
110 (Sub1) 1. Inverter PCB defect
Wrong connection of 3Φ Wrong connection of 3Φ power
141 (Sub2) 2. No power of R, S, T supplied
power supply cable (Reverse supply cable (Reverse direction /
155 (Sub3) 3. Wrong connection of R, S, T cables
Basic Part
direction / missing a phase) missing a phase)
Plus II: 4. Main fuse defect
541,542,
543,544
Is connection and phase

No
order of power cables to main / Connect correctly
sub outdoor unit correct?*
Troubleshooting
Guide for each
Yes
Error Code
Is connection and phase No Connect power cables in
order of power distribution
distribution panel correctly
panel correct?**
Yes
Is CH 54 occurred again No
after reset MAIN End
circuit breaker?
Yes
Component Check
Electrical
Is 3Φ Fuse normal? No
[refer electric Replace Fuse
component part]
Yes
Check the diode of inverter
fan PCB and in case of fault
replace inverter fan PCB
Is noise filter
normal? No
Replace NOISE FILTER
Solution Check
[refer electric
component part]
Yes
Replace inverter compressor

PCB(CH54), SUB PCB(CH110,141,155)
* Check power cable connection state, **Check power cable connection state, phase order, power
phase (R-S-T) order, power supply state supply state in distribution panel
in control box of product
Test functions
-114-
supplied)
(plus)
Basic Part

(when power is
not supplied)
Troubleshooting
Guide for each
Error Code
(Noise emit & (when power is be within 0~40V It is disconnected
protect) Supplied)  Replace noise filter
(Plus) (Plus II)
Component Check
Electrical
Solution Check
(When power should be within 0~10Ω ∞, noise filter is
Test functions
-115-
Installing old Sub

Slave ODU mixed ODU and
Plus II: 1Installing LGDC Slave Unit and Super sub
installation new slave ODU
591 Unit together
together
Basic Part
No
Installed 3 UNIT or more? Recheck power and installation condition
Yes
Troubleshooting
Guide for each
Error Code
Is LGDC Slave Unit No
Recheck power and installation condition
installed?
Yes
No
Is Super Sub Unit
installed ?
Yes
Component Check
Slave,Sub Unit mixed installation
Electrical
Solution Check
Test functions
-116-
EEPROM Access error

Plus II: Inverter PCB EEPROM and 1. EEPROM contact defect/wrong insertion
601,602, error Check SUM error 2. Different EEPROM Version
603,604 3. ODU inverter PCB assembly damage
Basic Part
No 1.Check EEPROM insert direction/connection condition

Is EEPROM insertion
2.Check EEPROM Check SUM
normal?
Replace if abnormality found
Yes
Troubleshooting
Guide for each
Error Code
Is inverter PCB assembly No
Replace inverter PCB assembly
normal?
Yes
Inverter EEPROM
Component Check
Electrical
Solution Check
Test functions
-117-
1. Defect of heat sink cooling fan

Plus: 2. Defect of inverter compressor PCB
Heat sink over heat Heat sink over heat
62 3. Loose connection of connector of cooling fan
4. Defect of temperature sensor of heat sink
Basic Part
Is resistance value
Does cooling fan No No
of cooling fan coil correct?
rotate while compressor Replace cooling fan
[refer electric
operation?
component part]
Yes Yes
Troubleshooting
Guide for each
Replace main PCB
Error Code
No
Is value of sensor
Replace sensor
resistance normal?*
Yes
Replace inverter fan PCB
Component Check
* Heat sink temperature sensor (±5% tolerance) : 10℃ = 20.0㏀ : 25℃= 10.0㏀ : 50℃= 3.5㏀ : 85℃= 1.0㏀
Electrical
- Position of cooling fan drive connector in main PCB - Heat sink cooling fan
Solution Check
- Check DC 12V output during inverter - Heat sink temperature

compressor operation sensor connection
Test functions
-118-
Heat sink temperature 1. Loose connection of temperature sensor connector

Plus: Abnormal value of sensor
sensor error of inverter 2. Temperature sensor defect (Open/Short)
65 (Open/Short)
control PCB 2. Fan Main PCB defect
Basic Part
Connect PCB to sensor
to PCB correctly?
Yes
Troubleshooting
Guide for each
Is value of sensor No
Error Code
Replace sensor
resistance normal?*
Yes
* If value is 100 ㏀ ↑(open) or 100 Ω ↓(short), error occurs

Component Check
It is normal if value shown as below (±5% error)
Heat sink sensor(±5% tolerance) : 10℃ = 20.0㏀ : 25℃= 10.0㏀ : 50℃= 3.5㏀ : 85℃= 1.0㏀
Electrical
- Temperature sensor location of Heat sink - Measure the resistance of heat sink temperature sensor
Solution Check
Test functions
-119-
1. Fan motor defect / assembly

condition
abnormal
Fan RPM is 10RPM or less
2. Wrong connection of fan motor
Plus II: for 5 sec. when ODU fan
Basic Part
connector
671,672,673,673 starts or 40 RPM or less
(Hall sensor, U,V,W output)
after fan starting.
3. Reversing rotation after RPM target
Outdoor unit FAN apply
LOCK error 4. Fan PCB assembly defect
S N1 Right
After FAN drive signal
P 67 Fan 1. Motor connection defect
If the HALL SENSOR signal
A 2. FAN PCB defect
does not come on for 4 sec.
C N2 Left 3. Motor defect
E 67 Fan
Troubleshooting
Guide for each
Error Code
Error diagnosis and countermeasure flow chart(Plus)
Is the motor connection No

Reconnect motor connector
status normal?
Yes
Component Check
No
Is the motor normal?* Replace FAN motor
Electrical
Yes
Replace FAN PCB
* Check Hall sensor of BLDC FAN motor Ha(4),Hb(3) - Gnd(2) : 24MOhm
Ha(4),Hb(3) - Vcc(1) : 11KOhm
16.8Ω±5% (75℃)
Solution Check
* Check resistance of LGDC FAN motor power wire
Test functions
-120-
Error Code
-121-
16.8Ω±5% (75℃)
resistance
Constant Speed Constant Speed Constant Speed Compressor CT

Plus II:
Compressor CT Sensor Compressor CT Sensor Sensor
701,702,703,704
Error Open/short defect
Basic Part
Is constant speed compressor No Check constant speed compressor

CT Sensor connection condition
CT Sensor wiring condition and locking
normal?
Troubleshooting
Guide for each
Error Code
Yes
Component Check
Electrical
Solution Check
Test functions
-122-
Inverter input current Micom input voltage isn't 1. Input voltage abnormal (T-N)
Plus II:
CT within 2.5V ±0.3V at initial 2. ODU inverter PCB damage
711,712,713,714
sensor error state of power supply (CT sensing part)
Basic Part
Check
No R~S/S~T/T~R phase voltage is 380V ±10%
Is input voltage normal? R~N/S~N/T~N phase voltage is 220V ±10%
abnormal
Yes
Troubleshooting
Guide for each
No
Is inverter PCB assembly normal? Replace inverter PCB assembly
Error Code
Yes
Component Check
Electrical
Solution Check
Test functions
-123-
1.Overload operation (Pipe clogging/

Covering/EEV defect/Ref.
overcharge)
2.Compressor damage(Insulation
AC input instant over Inverter PCB input 3 phase
Basic Part
damage/Motor damage)
Plus II: current power
3.Input voltage abnormal(R,S,T,N)
731,732,733,734 error (Matter of current is over 50A(peak) for
4.Power line assemble condition
software) 2ms
abnormal
5.Inverter PCB assembly
damage(input current sensing part)
Troubleshooting
Guide for each
Error Code
1.Check Pipe clogging/distortion
2.Check Covering (Indoor/Outdoor Unit)
Is installation No
3.Check EEV connector assemble condition/normal operation
condition normal?
4.Check refrigerant pressure
Reassemble or manage if abnormality found
Yes
Check
Is input voltage normal?
R~N/S~N/T~N phase voltage is 220V ± 10%
Check connection condition and wiring if power is abnormal
Yes
Component Check
Electrical
1.Check R,S,T,N connection condition
Is AC input Wire connection No
2.Check wire disconnection and wiring
condition normal?
Reassemble if abnormality found
Yes
1.Check inverter PCB assembly U,V,W connector connection

Is compressor condition
No
Wire connection 2.Check wire disconnection and wiring
condition normal? 3.Check compressor terminal connection condition(bad contact)
Yes
Solution Check
Is inverter PCB assembly No Check inverter PCB assembly IPM normality
normal? Replace inverter PCB assembly
Yes
Recheck power and

Test functions
-124-
Error Code
-125-
During operation(compressor 1. CT sensor defect

frequency 2. Capacity over of AVR
Plus II: 3 Phase Power
is over 50Hz), difference 3. Bridge R-N or S-N or T-N phase
741,742,743,744 Unbalance
between R & T phase is 5A for voltage unequally at indoor unit
Basic Part
10 seconds. etc.
Check abnormal wiring between Inverter PCB assembly &

Is inverter PCB assembly No
bridge diode (misconnection,disconnection)
power wiring normal?
Rewiring if abnormal wiring found
Yes
Check
Troubleshooting
Guide for each
Error Code
R~N/S~N/T~N phase voltage is 220V ± 10%
Check connection condition and wiring if power is abnormal
Yes
Does indoor unit power No Bridge R-N,S-N,T-N voltage equally

bridge R,S,T phase equally?
Yes
Component Check
Is inverter PCB No
Replace inverter PCB assembly
assembly normal?
Electrical
Yes
Recheck power and

installing condition
Solution Check
Test functions
-126-
Offset of micom which senses

Plus II: the 1.Input voltage is abnormal(not 15V)
Fan CT sensor error
751.752,753,754 fan motor phase current is not 2.Fan PCB assembly defect
2.5V
Basic Part
No Check 15V wire connection

Reassemble or manage if abnormality found
Yes
Is Fan PCB assembly normal? No
Troubleshooting
Replace Fan PCB assembly
Guide for each

Error Code
Yes
Recheck power and

Component Check
Electrical
Solution Check
Test functions
-127-
Plus II: Fan DC Link High Fan PCB DC link voltage 1.Input power abnormal
761,762,763,764 Voltage Error supplied over 780V\ 2.Fan PCB assembly defect
Basic Part
Check
R~S/S~T/T~R phase voltage is 380V ± 10%
Is input voltage normal? No R~N/S~N/T~N phase voltage is 220V ± 10%
Yes abnormal
Troubleshooting
Guide for each
Is Fan PCB assembly normal? No
Error Code
Yes
Recheck power and

Component Check
Electrical
Solution Check
Test functions
-128-
1.Overload operation
Plus II: Fan Over Current Output current is over 5A for
2.Fan Motor defect
771,772,773,774 Error 40ms
3.Fan PCB assembly defect
Basic Part
Is installation No No Check ODU fan motor assemble condition and locking

condition normal? Reassemble or replace if abnormality found
Yes
1.Check resistance between each motor output terminal
Troubleshooting
Guide for each
Are the resistance No No (16.8Ω±5% at 75°C)
Error Code
Between each phase and insulation
2. Check insulation resistance between ODU fan motor
resistance of motor output
terminal (U,V,W) and pipe (over 100MΩ )
terminal normal?
Replace fan motor if abnormality found
Yes
1.Check if color of motor output terminal(U,V,W) connector

Is motor wire connection No matched with PCB’s
condition normal? 2.Check wire disconnection and wiring
Reassemble or replace if abnormality found
Yes
Component Check
No 1. Check fan PCB assembly IPM normal
Is Fan PCB assembly normal?
Electrical
Yes
Recheck power and

Solution Check
Test functions
-129-
1.Fan motor hall sensor defect

2.ODU fan motor hall sensor
Plus II: Fan Motor Hall Sensor Fan Motor Hall Sensor disconnection
781,782,783,784 Error short/open 3.ODU Fan Motor Hall Sensor wrong
Basic Part
insertion
4.Fan PCB assembly defect
Is fan motor assemble No Check ODU fan motor assemble condition and locking
Yes
Troubleshooting
Guide for each
Error Code
No
Is wiring between fan motor Recheck f an motor hall sensor connection
and PCB normal? Reassemble if abnormality found
Yes
Check if connector color matched between fan motor

Is connector color between No hall sensor and PCB
Hall Sensor PCB matched?
Component Check
Yes
Electrical
No Replace Fan PCB assembly
Is fan PCB assembly normal?
Yes
Recheck power and

Solution Check
Test functions
-130-
1.Fan motor defect/ assemble

condition abnormal
Plus II: Fan Starting Failure 2.Fan motor connector
Fan Motor initial starting failure
791,792,793,794 Error misconnection(Hall sensor,
Basic Part
U,V,W ouput)
3.Fan PCB defect
Is fan motor assemble No Check ODU fan motor assemble condition and locking
Yes
Troubleshooting
Guide for each
Error Code
1. Check resistance between each motor output terminal
Are the resistance No No (16.8 Ω ±5% at 75°C)
Between each phase and insulation
2. Check insulation resistance between ODU fan motor terminal
resistance of motor output
(U,V,W) and pipe (over 100MΩ)
terminal normal?
Replace fan motor if abnormality found
Yes
1. Check if color of motor output terminal(U,V,W) connector

Is fan motor connection No matched with PCB’s
condition normal? 2. Check wire disconnection and wiring
Reassemble or replace if abnormality found
Component Check
Yes
Electrical
No Check fan PCB assembly IPM normal
Is fan PCB assembly normal?
Yes
Recheck power and

Solution Check
Test functions
-131-
Plus II: Main PCB EEPROM 1. No EEPROM

EEPROM Access Error
861,862,863,864 Error 2. EEPROM wrong insertion
Basic Part
Is EEPROM assemble No Reset after checking EEPROM assemble condition

condition normal?
Yes
No
Troubleshooting
Guide for each
Is EEPROM 24C16? Replace EEPROM with 24C16
Error Code
Yes
Recheck power and

Component Check
Electrical
Solution Check
Test functions
-132-
Error occurs when checking 1.EEPROM bad contact/wrong

Plus II: Fan PCB EEPROM the EEPROM checksum as insertion
871,872,873,874 Error initializing after power is 2.EEPROM Version is different
supplied 3.ODU fan PCB assembly damage
Basic Part
1.Check EEPROM insertion direction/connection condition

Is EEPROM insertion normal? No 2.Check EEPROM checksum
Replace EEPROM if abnormality found
Yes
Troubleshooting
Guide for each
No
Error Code
Is Fan PCB assembly normal? Replace fan PCB assembly
Yes
Recheck power and

Component Check
Electrical
Solution Check
Test functions
-133-
plus:
Over-increase of constant Compressor is off because of
100,101 (Sub1)
compressor discharge Over-increase of constant compressor discharge Refer to CH33
102,103 (Sub2)
temperature of Sub outdoor temperature of Sub outdoor unit
152,153 (Sub3)
Basic Part
* Discharge temperature sensor of constant compressor
in the sub unit
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-134-
Plus:
104 (Main)
111 (Sub1)
142 (Sub2) Transmission 1. Loose connection of power cables
Master displays ODU number
156 (Sub3) Error /transmission cables (Open/Short)
Basic Part
which is not communicated.
Plus II: Between 2. Each outdoor unit PCB defect
Slave displays own error number
011→041 Outdoors 3. Defect of PCB power
011→042
011→043
011→044
Does transmission LED Is PCB input power of
Troubleshooting
No No Check and replace
Guide for each

(Red) of corresponding transformer, PCB power fuse corresponding parts/
Error Code
Sub PCB blinks? [refer electric normal? [refer electric Input power
component part] component part]
Yes Yes
Replace related SUB PCB
Is transmission cables
No
Component Check
of outdoors connected
correctly? [refer electric Re-connect transmission cables
component part]
Electrical
Yes
Replace MAIN PCB
Sub unit PCB
LED 8 7 6 5 4 Solution Check

LED 3
LED 2
LED 1
40 sec later after power input,
LED1(blinking): Display normal micom condition

Test functions
LED2, 3(On): Back-up for left/right compressor

LED4 : reserved
LED5(blinking) : Communicate with main
LED6(On) : Reverse connection at sub unit
LED7(On) : Right compressor is in operation
LED8(On) : Left compressor is in operation
-135-
Error Code
-136-
-Plus
1. Loose connection of transmission cables
Plus:Transmission error Plus:Transmission error between 2. Transmission cables are open/sort
Plus:105
between outdoor unit Main PCB outdoor Main PCB and fan Main 3. Outdoor Main PCB PCB defect
Plus II:
and fan Main PCB PCB (Fan → outdoor main) 4. Fan Main PCB defect
Basic Part
11→051
11→52
Plus II:Transmission error Plus:Transmission error between -Plus II
11→53
between outdoor unit Inv PCB outdoor Inv PCB and fan PCB 1. Wrong connection between Inverter and
11→54
and fan PCB (Fan → inv) Fan PCB
2. Fan PCB power not supplied
3. ODU Inv/Fan PCB defect
Troubleshooting
Is transmission LED Is noise filter or fuse
Guide for each

No No
(yellow) of inverter fan normal ? [refer electric Replace noise filter or fuse
Error Code
PCB on?* component part]
Yes
Yes
Are transmission cables No

of Main PCB / Fan PCB Re-connect transmission cables
connected normally?
Component Check
Yes
Electrical
Is green LED of No
Replace Main PCB
Main PCB blinks?**
Yes
Solution Check
* Location of inverter transmission connector of **Location of PCB transmission connector of
Main PCB and LED Inverter FAN and LED
Test functions
-137-
Error Code
-138-
Plus:106
Plus II:
11→061 1. Overload operation (Pipe
12→062 clogging/Covering/EEV
Basic Part
13→063 IPM protection circuit defect/Ref. overcharge
14→064 Over current of Main outdoor activation 2. ODU fan motor assemble condition abnormal
fan motor (inverter fan IPM fault) (over current / (Coil disconnection/Short/Insulation damage)
S N1 Right overheating) 3. Fan PCB heatsink assemble condition
P 106 Fan abnormal
A 4. Fan PCB assembly defect
C N2 Left
E 106 Fan
Troubleshooting
Guide for each
Error Code
No
Is it Multi V Space ? Multi V Plus & Sync
Yes
Yes
Is inverter fan IPM PCB No

전원선과 신호선 이격 normal? [refer electric Replace inverter fan IPM PCB
component part]
Yes
Component Check
Is inverter fan PCB No
Normal? [refer electric Replace inverter fan PCB
component part]
Electrical
Yes
Is inverter fan motor No

Normal? [refer electric Replace inverter fan motor
component part]
Yes
Solution Check
Adjust connection after
check PWM signal cables
* check fan motor

- [Multi V Plus & Sync]Check Inv the resistance
on fan motor connectors - [Multi V Space] Check hall sensor of BLDC fan motor
- Resistance between cables : 18 ±3Ω Ha(4),Hb(3) - Gnd(2) : 24 MΩ

- Resistance between cables(LGDC fan) : 19 ±7% (75℃) Ha(4),Hb(3) - Vcc(1) : 11 kΩ
Test functions
Vcc
Gnd
1 Hb
2 Ha
3 4
-139-
Part Check
(Function) points
Inverter fan
IPM PCB
Basic Part
1. PWM signal connector
4. IPM
2. DC supply terminal
(DC310V)
Troubleshooting
Guide for each
Error Code
3. Outdoor unit fan connectors
Component Check
Electrical
1.PWM signal -Check 9pin connectors -Replace cables & check
2.Fan DC power - DC voltage should be charged of 310V soldering condition of
3.Outdoor - While Fan operating, in case voltage of PCB
fan connector - connectors(U-V,V-W,U-W) is 100~300V - Replace connectors &
- → Normal inverter
4. IPM -- Check Diode(P-N : 0.95V, PCB if not charging
- P-U,P-V,P-W: 0.55V
- N-U,N-V,N-W: 0.55V - Replace inverter IPM
PCB
Solution Check
Test functions
DIODE측정(P-U : 0.5V)
-140-
Part Check
(Function) points
No power
on PCB
10. Comm. circuit
Basic Part
2. Input circuit of 3φ &
1. MICOM LED DC rectifying circuit
9. On-boarding 3. In/Output connector

connector of reactor
8. Heat sink
Troubleshooting
Guide for each
temperature 4. DC-Link output voltage
Error Code
sensor connector
7. PWM
drive circuit
5. DC-Link electrolytic
capacitor
6. SMPS power
circuit
Component Check
Electrical
2.3φ power -Input voltage of 3φ 4 wires should be -Check supply voltage,
Input circuit 3φ 380V, 1φ 220V noise
- Check half wave rectifying circuit diode filter, fuse
(R-Reactor1: 0.6V, S-Reactor1: 0.6V: -Replace inverter fan
T-Reactor1: 0.6V) PCB
Solution Check
R, S, T, N Reactor 1
10. -Yellow LED should blink. -Check yellow LED blinks

Transmission or not
Test functions
circuit with -When is OFF / ON

main PCB continuously,
check transmission
with main PCB
Red LED -When red LED blinks, error code happens -Check error code at
about inverter fan PCB main PCB
-141-
Multi V Space BLDC FAN PCB
4.SW_SEL 6.CN_COMM
LED01M : PWM Enable 5.SW_DIR [MAIN PCB>FAN PCB] :5,6,8HP
Basic Part
[louver
LED02M : display error [FAN direction] [FAN>COMP PCB] : 10HP
selection]
7.CN_POWER2
3.Power supply [louver power supply]
LED01K
(FAN>INV
communication)
8.SW01M,02M,03M
Troubleshooting
[PCB JIG check]
Guide for each

9.CN_WIRTE
Error Code
[on boarding
light]
10.CN_M1S,M2S
[louver signal input]
2.CN_DC LINK 11.CN_SENSOR

[DC power supply [FAN signal input]
sensor)
12.CN_MOTOR1,2
1.CN_POWER
[louver signal output]
[PCB power
supply)
Component Check
13.CN_FAN
[FAN signal output)
Electrical
Situation Monitoring Location How to check? Counter-measure
Power does not turn 1.CN POWER -AC voltage measure 220V -Input voltage (220V)
on -Replace related parts
3. Power supply - ZNR01D( barrister ),FUSE burn out
(CH105) checkup
FAN motion disabled 2.CN_DC LIINK -DC 470V~520V displays - Check and replace
CAPACITOR
Solution Check
-DC 380V and above are normal
- Replace PCB
13.CN_FAN - U,V,W electric flow measurement - Check up and replace
(CH106) stabilize connection and motor
11.CN_SENSOR -Check connectors
(CH67)
communication does 6. CN-COMM -Flick LED01K -Check PCB power

not work (CH105) - check connector and PCB (power supply(220V)
supply ,communication) -Check and replace connector
and PCB
Louver does not 4.SW_SEL Check if connector is connected -connect connectors (if there
work -DC24V display check are no louver)
Test functions
7.CN_POWER2
-Connection status check -Check and Replace trance and
10.CN_M1S,M2S power supply
Connection status check
12.CN_MOTOR1,2 -Check and replace louver
motor and connection part
Check and replace louver

motor and connection part
-142-
Error diagnosis and countermeasure flow chart (Plus II)
No
Is fan motor assemble Check ODU fan motor assemble condition and locking
Basic Part
Yes
No 1.Check fan motor U,V,W connector connection condition

Is fan motor wire connection Reassemble wire if abnormality found
condition normal? 2.Check fan motor wire disconnection
Replace ODU fan motor if abnormality found
Yes
1.Check fan PCB connector condition
Troubleshooting
Is fan PCB assemble No Reassemble if abnormality found
Guide for each

condition normal? 2.Check assemble condition between fan PCB and Heatsink
Error Code
Reassemble heatsink if abnormality found
Yes
No
Is fan PCB assembly normal? Replace fan PCB assembly
Yes
Component Check
Electrical
Recheck power and
installation condition]
(FAN PCB)
Solution Check
(FAN PCB) (FAN PCB)

Test functions
-143-
Multi V Plus II LGDC FAN PCB
Basic Part
CN Micom N
Write
V 2. CN FAN Right
Troubleshooting
Guide for each
1. CN DC Link
Error Code
CN Heat Sink
6. CN Inverter
Communication
DC 15V Power Input 3. CN FAN Left

terminal
4. CN Hall Sensor
P
Component Check
(Right)
Electrical
5. CN Hall Sensor
(Left)
FAN motion disabled 1.CN_DC LIINK -DC 470V~520V displays - Check DC Voltage at FAN PCB
-DC 380V and above are normal terminal (more than 380V—
Normal)
2/3. CN_FAN - U,V,W electric flow measurement - Replace PCB
(CH106) stabilize - Check up and replace
Solution Check
-Check connectors connection and motor
4/5. CN_HALL
SENSOR(CH67)
Communication does 6. CN-COM (CH105) -Flick LED01K - Check DC power input

not work - Check 15V DC power input terminal
- Check Connector - Check and replace connector
and PCB
Fan IPM P-N & U,V,W

Test functions
-144-
Plus:107
Plus II:
11→071
12→072
13→073 DC voltage charging Low voltage of Main 1. Bad connection of voltage lead cable of main PCB DC link
Basic Part
14→074 failure of inverter fan outdoor fan motor 2. Fan main PCB capacitor defect
S N1 Right motor drive (below 380V) 3. Fan main PCB defect
P 107 Fan
A
C N2 Left
E 107 Fan
Troubleshooting
Guide for each
Error Code
Is DC LINK cable No
Adjust DC LINK cables
Normal?*
Yes
Component Check
Electrical
No 1. Check DC_Link Wire connection

Is wiring between fan motor
2. DC_Link
and PCB normal?
Replace wire if abnormality found
Yes
No Solution Check
Measure DC_Link voltage
Is DC_Link voltage normal?
Check inverter PCB if voltage is below 380V
Yes
No
Is Fan PCB assembly normal? Replace fan PCB assembly
Yes
Test functions
-145-
Error Code
- Inverter fan IPM PCB
Check DC Voltage 470~520
-146-
(Plus II)
(Plus)
- Inverter fan main PCB
Plus:
Excessive rise of high pressure in Compressor Off due to the high pressure switch
109 Refer to CH24
outdoor unit in outdoor unit
(Sub1)
Basic Part
Plus: Outdoor 3 phase power supply problem
Wrong connection of 3 phase power cable
110 (Reverse phase / No power in 1 or 2 Refer to CH54
(Reverse phase / Phase omission)
(Sub1) phase)
104 → transmission error between the outdoor

Plus: units (Main outdoor unit is not receiving signal
Transmission error between outdoor
111 from Sub units) Refer to CH104
units
(Sub1) 147, 149, 171 → Sub outdoor units are not
receiving signal from Main outdoor unit
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-147-
Plus:
113 (Main)
125 (Sub1)
Outdoor unit
137 (Sub2)
liquid pipe Abnormal sensor 1. Defective temperature sensor connection
166 (Sub3)
(condenser) resistance value 2. Temperature sensor defect(Open / Short)
Plus II:
Basic Part
temperature (Open/Short) 3. Outdoor unit main PCB defect
11→131
sensor error
12→132
13→133
14→134
Plus:
114 (Main sub-cool inlet)
115 (Main sub-cool outlet)
126 (Sub1 sub-cool inlet)
127 (Sub1 sub-cool outlet)
Troubleshooting
Guide for each
138 (Sub2 sub-cool inlet)
Error Code
139 (Sub2 sub-cool outlet)
167 Sub3 sub-cool inlet)
Outdoor unit sub- 1. Defective temperature sensor connecter
168 (Sub3 sub-cool outlet) Abnormal sensor
cooling inlet / outlet connection
resistance value
temperature sensor 2. Temperature sensor defect(Open / Short)
Plus II: (Open/Short)
error 3. Outdoor unit main PCB defect
11→141(sub-cool inlet)
12→142
13→143
14→144,
11→151(sub-cool outlet)
11→152
11→153
11→154
Component Check
Electrical
• Sub-cool circuit in the
outdoor unit
Is temperature sensor No
connector connections Check and correct connection
are normal?
Yes
Is the value of temperature No

Replace sensor (Plus)
sensor resistance normal?*
Yes Solution Check
Replace outdoor unit PCB
* Sensor resistance 100 ㏀ over (open) or 100 Ω below (short) will generate error (Plus II) (Plus II)
Note: Temperate sensor resistance vary with temperature, So compare temperature sensor resistance value
according to outdoor unit temperature by referring below table (±5% tolerance)
Air temperature sensor: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Pipe temperature sensor: 10℃ = 10㏀ : 25℃= 5㏀ : 50℃= 1.8㏀
Test functions
- Liquid pipe temp sensor - Sub-cool inlet temp sensor - Sub-cool outlet temp sensor
-148-
116 Sensor measured value of resistance is

High pressure sensor Refer CH43
(Plus Sub1) abnormal (Open / Short)
Basic Part
117 Sensor measured value of resistance is
Low pressure sensor Refer to CH42
(Plus Sub1) abnormal (Open/Short)
118 Outdoor unit air temperature Sensor measured value of resistance is

Refer to CH44
(Plus Sub1) sensor error abnormal (Open / Short)
120 Compressor suction pipe Sensor measured of resistance value is

Refer to CH46
(Plus Sub1) temperature sensor error abnormal (Open/Short)
Troubleshooting
Guide for each
121 (Plus Sub1
Error Code
constant compressor 1) Compressor discharge pipe Sensor measured value of resistance is
Refer to CH41
122 (Plus Sub1 temperature sensor error abnormal (Open/Short)
constant compressor 2)
123 (Plus Sub1 HEX A) Sub outdoor unit heat exchanger Sensor measured value of resistance is
Refer to CH45
124 (Plus Sub1 HEX B) (A,B) pipe sensor error. abnormal (Open/Short)
125 Outdoor liquid pipe (condenser) Sensor measured value of resistance is

Refer to CH113
(Plus Sub1) sensor error abnormal (Open/Short)
Component Check
126 (Plus Sub1
Sub-cool inlet) Outdoor unit sub-cool inlet / outlet Sensor measured value of resistance is
Electrical
Refer to CH114
127(Plus Sub1 sensor error abnormal (Open/Short)
Sub-cool outlet)
128 Sensor measured value is abnormal

High pressure sensor error Refer to CH43
(Plus Sub2) (Open/Short)
129 Sensor measured value is abnormal

Low pressure sensor error Refer to CH42
(Plus Sub2) (Open/Short)
Solution Check
130 Outdoor unit air temperature Sensor measured value is abnormal
Refer to CH44
(Plus Sub2) sensor error (Open/Short)
132 Compressor suction temperature Sensor measured value is abnormal

Refer to CH46
(Plus Sub2) sensor error (Open/Short)
133 (Plus Sub2 Const

compressor1) Compressor discharge pipe Sensor measured value is abnormal
Refer to CH41
134 (Plus Sub2 Const temperature sensor error (Open/Short)
compressor2)
Test functions
Sub Outdoor unit heat exchanger

135 (Plus Sub2 HEX A) Sensor measured value is abnormal
(A,B) pipe temperature sensor Refer to CH45
136 (Plus Sub2 HEX B) (Open/Short)
error
137 (Plus Sub2

Sub-cool Liquid Pipe)
Outdoor unit Sub-cool Liquid Pipe,
138 (Plus Sub2 Sensor measured value is abnormal
Inlet / outlet temperature sensor Refer to CH113/114
Sub-cool inlet) (Open/Short)
error
139 (Plus Sub2
Sub-cool outlet)
-149-
140 Excessive rise in outdoor high Compressor Off due to the high pressure
Refer to CH24
(Plus Sub2) pressure switch in outdoor unit
Outdoor 3 phase power supply
Basic Part
141 Wrong wiring at outdoor unit
problem (Reverse phase / phase Refer to CH54
(Plus Sub2) (phase reversal / phase omission )
omission)
Transmission error between outdoor units

104 (Main outdoor unit is not receiving sub
142 Transmission error between outdoor
outdoor unit s signals) Refer to CH104
(Plus Sub2) units
147, 149, 171 (Sub outdoor units are not
receiving main unit signals)
Troubleshooting
Guide for each
143 (Plus Sub1)
Excessive rise in high pressure Compressor Off due to high pressure sensor Refer to CH34
Error Code
145 (Plus Sub2)
144 (Plus Sub1)

Excessive drop in low pressure Compressor Off due to low pressure sensor Refer to CH35
146 (Plus Sub2)
1. Input Voltage in the installation region =

147 (Plus Sub1)
Low voltage/ High voltage 3phase 380V±10% Refer to CH25
149 (Plus Sub2)
2. Single Phase = 220 ±10%
Component Check
Electrical
148 (Plus Sub1)
Outdoor voltage sensing error Measured value is abnormal (Open/Short) Refer to CH49
150 (Plus Sub2)
Solution Check
Test functions
-150-
Plus:
151
Function error of 4way 1. Wrong operation of 4way valve because of sludge etc. inflow
Plus II: Function error of
(reversing valve) in 2. No pressure difference because of compressor fault
11→511 outdoor 4way
Main or Sub outdoor 3. Wrong installation of In/outdoor common pipe
11→512 (reversing valve)
units 4. 4way valve defect
Basic Part
11→513
11→514
Is 4-Way valve connecter No

connection are properly Reconnect it
connected?
Troubleshooting
Yes
Guide for each

Error Code
Is 4 Way valve coil No
Change 4 Way valve coil
resistance normal?*
Yes
Is 4 way valve coil connected No

Re-insert 4 way valve coil
to 4 way valve normally?**
Yes
Component Check
In case of more than
2 units, does main outdoor No
Refer to CH 51 & make measure
Electrical
unit recognize
예 as more
than 2 units? ***
Yes
After reset, can we

check supply voltage at PCB No
when starting heating
mode operation****
Yes
No Check and replace compressor,
Solution Check
Is compressor working
Magnet switch, corresponding PCB
normally?
Yes
After opposite
mode operation to present No If the same error is occurred in
mode, is the same error near future replace 4way valve
occurred again?
Yes
Replace 4 way valve*****

Test functions
-151-
(Plus)
* Measure the resistance of 4way valve

* Location of 4way valve connector on
Main / Sub PCB (marked as 4way)
Basic Part
Troubleshooting
Guide for each
Error Code
** Confirm the 4way valve coil is inserted to the end
Component Check
Electrical
*** When power is supplied in order as follow (Sub2Sub1Main)
3rd number indicates outdoor quantity at Main PCB 7-segment LED
- Outdoor unit 1set : Model code-capacity(or 10)-..
- Outdoor unit 2set : Model code(Main)-Model code(sub)-capacity(or 20)-..
- Outdoor unit 3set : Model code(Main)-Model code(sub1)- Model code(sub2)- capacity(or 30)- ..
Solution Check
**** Check the output voltage of terminal socket ***** Checking method for outdoor unit of 3unit system
during heating operation : 220V (±10%) ① Close all the SVC valves of high / low pressure common pipe
② Operate system
③ Check the difference of high and low pressure
with LGMV for each unit (Main, Sub1, Sub2)
④ If there is a unit in which the difference is not increased
then the 4way valve of that unit is defective
Test functions
-152-
Error Code
-153-
Main PCB
(Plus ΙΙ)
152,153 Excessive rise of the constant Constant speed compressor Off due to the
Refer to CH33
(Plus Sub3) compressor discharge temperature excessive rise in discharge temp
154 Excessive rise in outdoor high Compressor Off due to the high pressure
Basic Part
Refer to CH24
(Plus Sub3) pressure switch in outdoor unit
Outdoor 3 phase power supply

155 Wrong wiring at the outdoor 3 phase
wiring wrong Refer to CH54
(Plus Sub3) (Reverse phase / Phase omission)
(Reverse phase / Phase omission)
transmission error between outdoor units

104 (Main outdoor unit is not receiving sub
156 transmission error between
outdoor unit s signals) Refer to CH104
(Plus Sub3) outdoor units
147, 149, 171 (Sub outdoor units are not
Troubleshooting
Guide for each
receiving main unit signals)
Error Code
157 Abnormal resistance value of sensor
High pressure sensor error Refer to CH43
(Plus Sub3) measurement ( Open / Short )
158 Abnormal resistance value of sensor

Low pressure sensor error Refer to CH42
(Plus Sub3) measurement ( Open / Short )
159 Outdoor unit air temperature Abnormal resistance value of sensor

Refer to CH44
(Plus Sub3) sensor error measurement ( Open / Short )
Compressor suction Abnormal resistance value of sensor
Component Check
161(Plus Sub3) Refer to CH46
temperature error measurement ( Open / Short )
Electrical
162 (Plus Sub3 constant
compressor1) Compressor discharge pipe Abnormal resistance value of sensor
Refer to CH41
163 (Plus Sub3 constant temperature sensor error measurement ( Open / Short )
ompressor2)
164 (Plus Sub3 HEX A) Pipe sensor error of the main and Abnormal resistance value of sensor
Refer to CH45
165 (Plus Sub3 HEX B) sub units heat exchanger (A,B) measurement ( Open / Short )
Abnormal resistance value of sensor

Sensor error at the outdoor
166(Plus Sub3) measurement Refer CH113
liquid refrigerant pipe
Solution Check
( Open / Short )
167 (Plus Sub3 sub-

cooling inlet) Outdoor unit sub-cooling sensor Abnormal resistance value of sensor
Refer to CH114
168 (Plus Sub3 sub- error at inlet / outlet measurement ( Open / Short )
cooling outlet)
Compressor Off due to the high pressure

169(Plus Sub3) Excessive rise in high pressure Refer to CH34
sensor
Compressor Off due to the low pressure

170(Plus Sub3) Excessive low pressure drop Refer to CH35
sensor
Test functions
1.Input voltage in the installation region

Excessive Low voltage / High
171(Plus Sub3) = 3phase 380V±10% Refer to CH25
voltage
2. Single phase = 220V ±10%
Abnormal resistance value of sensor

172(Plus Sub3) Outdoor voltage sensing error Refer to CH49
measurement ( Open / Short )
-154-
Plus:
173
(MAIN constant)
174, 175 1. Constant compressor defect
Over-increase of
(sub1 constant 1,2) 2. Discharge temperature sensor defect
temperature
176, 177 Abnormal staring of 3. Outdoor temperature sensor defect
Basic Part
after constant
(sub2 constant 1,2) constant compressor 4. Outdoor main PCB defect
compressor
Plus II: 5. Magnet switch defect
starts
11→731 6. Wrong connection of constant compressor cables
11→732
11→733
11→734
Troubleshooting
Guide for each
Is resistance value
Error Code
(insulation & phase to phase)
of corresponding constant No
Replace constant compressor
compressor normal ?
[refer electric
component part]
Yes
No
Is cables’ connection
Adjust connection of cables
of compressor normal? *
Component Check
Yes
Electrical
Is discharge temperature
No
sensor of compressor Replace discharge
normal? [refer electric temperature sensor
component part]
Yes
Is magnet switch No
normal? [refer
예 electric Replace magnet switch
component part]
Solution Check
Yes
Is outdoor air temperature No Replace outdoor air

sensor normal? temperature sensor
Yes
* cables connection between constant compressor
and magnetic switch
Test functions
(Puls) (Puls II)
-155-
Multi V Water II Error happen because of 3 times

180 successive compressor off due
Anti-Freezing Error of 1. Insufficient water flow rate
Master (11801) to over-decrease of temperature
Plate Heat Exchanger 2. Temperature sensor defect
Slave1 (12802) by water pipe sensor and Heat
Slave2 (13803) exchanger sensor
Basic Part
No
Is water flow rate normal? Check Water flow rate and Power reset
Troubleshooting
Guide for each
Yes
Error Code
No
Is temperature sensor
Connect temperature sensor on PCB
Connection Condition normal? *
Yes
No
Replace temperature sensor
temperature sensor normal?
Component Check
Yes
Electrical

Sensor of air temperature: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Solution Check
Test functions
-156-
Multi V Water II
181 1. Bad connection of temperatureconnector
Water temperature Abnormal value of sensor
Master (11811) 2. Temperaure sensor defect
Sensor Error (Open / Short)
Slave1 (12812) 3. Outdoor PCB defect
Slave2 (13813)
Basic Part
No
Is temperature sensor
Connection Condition normal? Connect temperature sensor on PCB
Troubleshooting
Guide for each
Yes
Error Code
No
Replace temperature sensor
temperature sensor normal?
Yes
Component Check
Electrical
Sensor of air temperature: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Solution Check
Test functions
-157-
Multi V Water II
Transmission error
182 1. Power cable or transmission cable is not
between Main PCB can’t receive
Master (11821) connected
(Main PCB Sub signal from Sub PCB
Slave1 (12822) 2. Defect of Sub / Main PCB
PCB)
Slave2 (13823)
Basic Part
No
Is Sub Mciom LED blink? Push reset button
Troubleshooting
Guide for each
Yes
Error Code
No
Is Error disappear ? Instant Error
Yes
Replace outdoor unit Main PCB
Component Check
Electrical
Solution Check
Test functions
-158-
Plus II:
11→931 Heat sink
Fan PCB heatsink 1. Heatsink temperature sensor defect
11→932 temperature is
temperature high 2. Fan PCB assembly defect
11→933 over 95°C
11→934
Basic Part
Plus II: 1. Heatsink temperature sensor
Heatsink
11→941 Fan PCB heatsink defect(Open/Short)
Temperature
11→942 temperature sensor 2. Wrong connection of temperature sensor
Sensor
11→943 error connector
Abnormal
11→944 3. Fan PCB assembly defect
Troubleshooting
Guide for each
Error Code
Is temperature sensor No Check connection of heat sink
inserted to fan PCB? temperature connector
Yes
No
Is temperature sensor Check connection condition of
attached to heat sink? heat sink and temperature sensor
Component Check
Yes
Check heat sink temperature
Electrical
sensor wire disconnection
No
Is termperature ➔ Measure temperature sensor
sensor normal? resistance(10kΩ ±5% at 25°C)
➔ Replace the sensor if
abnormality found
Yes
No
Is fan PCB assembly
예 normal? Replace fan PCB assembly
Solution Check
Yes
Recheck power and installation

condition
Test functions
-159-
Error
Error Code Meaning Main Causes
Contents
1. HR unit’s power cable or transmission cable connection defect

After the Auto operation,
2. After Auto-Addressing, wrong address setting of the indoor
if the number of the indoor
Pipe detection unit (Defective indoor power / transmission error and PCB
200 units detected is different
error defect)
Basic Part
from the number
3. Wrong setting of the HR unit’s rotary switch or dip switch
communicating indoor unit
4. HR unit PCB defect
H1 01…H1 04
failed to search pipe 1. HR unit’s power cable or transmission cable connection defect
H2 01…H2 04
connected to HR unit valve 2. After Auto-Addressing, wrong address setting of the indoor
H3 01…H3 04 Pipe
of marked number unit
H4 01…H4 04 detection
(Ex : H1 02 no.2 valve (Defective indoor power / transmission error and PCB defect)
. error
pipe of no.1 HR unit failed 3. Wrong setting of the HR unit’s rotary switch or dip switch
.
to search) 4. HR unit PCB defect
.
Troubleshooting
Guide for each
Error Code
H.R. unit green No

LED (communication LED) blinks Check H.R. unit input power (220V±10%)
periodically ?
Yes
Yes
Check installation status of communication line
Component Check
Check H.R. unit Rotary switch and and connected pipe
Dip Switch setting outdoor unit ↔HR unit ↔outdoor unit
Electrical
Yes Yes
Check if all indoor unit is CH05 with

Operate auto pipe detection after the H.R. unit on (Refer to CH05)
pipe is sufficiently refrigerated
after resetting outdoor unit
and HR unit 30 minutes before
Yes
Solution Check
Is the Auto-pipe detection No
success? Adjust H.R. unit manual pipe detection
(is the Error disappeared?)
Yes
Finish
Test functions
[NB] If Indoor units/transmission cables of HR unit and cables of power 220V has been changed each other,
transmission parts and indoor will be burnt
-160-
▶ Auto addressing
Turn on “HR unit  Indoor unit 

Outdoor unit” in the order named ▶ Outdoor unit main PCB
Basic Part
<7 Segment>
Wait for 3 minute
Press SW02M of the ODU main PCB
Troubleshooting
for 5 seconds
Guide for each

Error Code
’88’ is displayed on the ODU main PCB and
the HRU PCB
After 2~7 minute, the number of IDU

connected is displayed at 7-seg of the
Component Check
ODU main PCB
<SW03M>
Electrical
(Dip switch)
The number of HRU connected is displayed

at 7-seg of the ODU main PCB
<SW02M> <SW01M>
Solution Check
Equal number of “IDU No
and displayed one”?
in terms of “wiring”
Check power and communication wiring
Yes between ODU, HRU, IDU
Retry auto addressing after solving problem

Completion of the IDU auto addressing
Test functions
-161-
▶ Auto pipe detection
Confirm the IDU auto addressing setting
Basic Part
Turn off “No.1 of SW02M of the HRU”
Check the proper setting of

No. 2 & 3 of SW02M of the HRU
(Model of HRU & number of IDU)
Reset the power of HRU PCB
Troubleshooting
Guide for each
Error Code
Confirm the No. 5 DIP S/W of SW01B
of the ODU PCB
- Outdoor temp is over 15℃ : ON
- Outdoor temp is below 15 ℃ : OFF
In case of changing 5 DIP S/W of SW01B

of the ODU, reset power of the ODU main
PCB.
Component Check
Electrical
Wait for 3 minute
Press SW01V of the ODU main PCB

for 5 second

at 7-seg of the ODU main PCB, and
then ’88’ is displayed
Solution Check
Outdoor unit is operating
for 5~30 minutes.
After ODU stopped, the number of IDU Display error on the ODU PCB / HRU PCB
detected is displayed at 7-seg of the ODU - ODU PCB : HR unit No.  Valve No.
main PCB for 1 minute (Example: H1 01)
- HRU PCB : ‘200’
Test functions
Equal number of IDU No

and displayed one?
in terms of “piping” Check the piping among ODU, IDU, HRU
Yes
Completion of the auto pipe detection Retry auto pipe detection
-162-
▶ Manual pipe detection
In case of auto pipe detection failure
Basic Part
Turn on “No.1 of SW02M of HR unit”
Troubleshooting
Enter central control address into each IDU
Guide for each

using its wired remote controller
Error Code
Manually set the address of each valve
corresponding with the central control
address of IDU connected to the valve
Component Check
Turn on No.5 of SW01B
of ODU PCB”
Electrical
Reset the power of ODU PCB
Wait for about 5 minutes
Solution Check
The number of IDU installed is displayed
No
Equal number of
“IDU and Displayed one”?
Yes
Test functions
Turn off No.5 of SW01B Check the central control address of IDU
of ODU PCB and HRU
Completion of the manual pipe detection Retry manual pipe detection
-163-
Error Code
-164-
▶ Switch setup of HR Unit
▶ HR Unit PCB
Green LED blinking :

Communication OK
Error Code
-165-
Error Code
-166-
▶ Manual addressing of valves on HR unit PCB
(with SW01M, SW03M, SW04M)
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
- Operation: None
- Display: None
Electrical
SW01M SW03M SW04M
No.1 of SW01M
- Operatoin : No.1 of SW01M on to address value #1
- Display : Existing value saved in EEPROM is
dsplayed in 7-SEG.
SW01M SW03M SW04M
- Opeation :Set the digit of 10 to the number in
Solution Check
Group High data of the wired remote control
connected to the corresponding indoor unit to the
SW03M
valve #1 by press SW03M S/W
SW01M SW04M
- Display : Digit increasing with the times of press
SW03M SW03M S/W is displayed in left 7-SEG SW03M
-Operation : Set the digit of 1 to the number in

Group Low data of the wired remote control
connected to the corresponding indoor unit to the
valve #1 by press SW04M SW04M
SW01M SW03M -Display : Digit increasing with the times of press
SW04M SW04M S/W is displayed in right 7-SEG SW04M
Test functions
No.1 of SW01M
-Operation : No. 1 of SW01M off to save the
address of valve #1
-Display : “11” displayed in 7-SEG disappears
SW01M SW03M SW04M
-167-
201(HR unit1) 205(HR unit2) HR unit liquid

1. Defective temperature sensor connection
209(HR unit3) 213(HR unit4) pipe Abnormal value of sensor
2. Temperature sensor defect(Open/Short)
217(HR unit5) 221(HR unit6) temperature measurement ( Open / Short )
3. Defective HR unit PCB
225(HR unit7) 229(HR unit8) sensor error
Basic Part
HR unit
202(HR unit1) 206(HR unit2)
Sub-cooling 1. Defective temperature sensor connection
210(HR unit3) 214(HR unit4) Abnormal value of sensor
inlet pipe 2. Temperature sensor defect(Open/Short)
218(HR unit5) 222(HR unit6) measurement ( Open / Short )
temperature 3. Defective HR unit PCB
sensor error
HR unit
Sub-cooling Abnormal value of sensor 1. Defective temperature sensor connection
discharge pipe measurement 2. Temperature sensor defect(Open/Short)
temperature ( Open / Short ) 3. Defective HR unit PCB
sensor error
Troubleshooting
Guide for each
Error Code
Is the sensor connected to no

Reconnect sensor to PCB
HR unit PCB properly?
yes
Component Check
Is the sensor resistance no
Electrical
Replace sensor
level normal?*
yes
Replace HR unit PCB
* Sensor resistance 100 ㏀ over (open) or 100 Ω below (short) will generate error
Note: Temperate sensor resistance vary with temperature, So compare temperature sensor resistance value Solution Check
according to outdoor unit temperature by referring below table (±5% tolerance)
Air temperature sensor: 10℃ = 20.7㏀ : 25℃= 10㏀ : 50℃= 3.4㏀
Pipe temperature sensor: 10℃ = 10㏀ : 25℃= 5㏀ : 50℃= 1.8㏀
Test functions
-168-
1. Defective connection in HR unit power supply and

204(HR unit1) 208(HR unit2) transmission transmission
transmission connection
212(HR unit3) 216(HR unit4) error between error between
2. Wrong setting of the HR unit Rotary switch and
220(HR unit5) 224(HR unit6) the HR unit and the HR unit and
Dip switch
228(HR unit7) 232(HR unit8) outdoor unit outdoor unit
3. Defective HR unit PCB
Basic Part
H.R. unit green No

LED (communication LED) blinks Check H.R. unit input power (220V±10%)
periodically ?
Yes
Yes
Troubleshooting
Guide for each
Error Code
Check installation status of communication line
Check H.R. unit Rotary switch and and connected pipe
Dip Switch setting outdoor unit ↔HR unit ↔outdoor unit
Yes Yes
Replace HR unit PCB
Component Check
Electrical
[NB] If Indoor units/transmission cables of HR unit and cables of power 220V has been changed each other,
transmission parts and indoor will be burnt
Solution Check
Test functions
-169-
1. Defective transmission connection

Central controller transmission failure
2. Defective CNU
240 connector error between central controller
3. Incorrect IP address of central controller or CNU
(CNU Connection failure) and CNU
4. Defective transmission network
Basic Part
Error diagnosis and countermeasure method
1) Check transmission cables are connected correctly or not

2) If central controller is connected to total network, check IP of CNU, central controller
3) Replace CNU
1. Defective CNU
Central controller data Central controller to CNU data
Troubleshooting
241 2. Center controller initialization
Guide for each

transmission error (Sending error) transmission failure
failure
Error Code
Central controller receive Error CNU to Central controller on time 1. Defective CNU
242
(Data receiving error ) data receiving error 2. Central controller initialization error
When data length from 1. Mismatching

Central controller receive buffer
243 CNU is longer than data length 2. Defective CNU
overflow (In excess data receive)
defined at protocol 3. transmission noise error
1. Defective CNU
Central controller receive time out transmission failure
Component Check
244 2. Initialization failure of central
(Receiving time : 3sec ↑) between central controller and CNU
controller
Electrical
Data sending failure from central 1. CNU defect
245 Central controller Send Timeout controller to CNU within designated 2. Initialization failure of central
time controller
Data receiving failure of central 1. CNU defect

246 Central controller Receive Timeout controller from CNU within 2. Initialization failure of central
designated time controller
Solution Check
Test functions
-170-
1. NOISE occurs
2. CNU defect
Central controller Received check sum is different from 3. Temporary error of Timing mismatch
250
Check sum Error calculated check sum data 4. A/C product defect
5. PI485 communication cable open or
Basic Part
connection defect
1. NOISE occurs
2. CNU defect
Central controller 3. Temporary error of Timing mismatch
251 Length of received data : 0
Receive Zero Error 4. A/C product defect
connection defect
1. NOISE occurs
Troubleshooting
2. CNU defect
Guide for each

Central controller Setting address and actual address 3. Temporary error of Timing mismatch
Error Code
252
Wrong Address Error are different each other 4. A/C product defect
connection defect
1. NOISE occurs
2. CNU defect
Central controller 3. Temporary error of Timing mismatch
253 No response from air conditioner
Disconnection Error 4. A/C product defect
connection defect
Component Check
Electrical
Error diagnosis and countermeasure method
1) Check system setting address of central controller and actual address is matched or not
2) Re-start service program(engine) of central controller
3) Replace CNU
Solution Check
Test functions
-171-
Error Code
Electric Component
Check
-172-
3
.
3.1 How to check main control box?
(a) Plus
Basic Part
2 6
4
3
5
Troubleshooting
Guide for each
Error Code
1
No. Part Check

(Function) points
Component Check
1 T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within 380±10% -Check supply power
(Terminal - Voltage of 1φ(R-N,S-N,T-N) should be within 220±10%. and connection
Electrical
Block, - Voltage fluctuation should be within 10V condition
Input - While stand-by and in operation,
power)
Check Ω - Resistance of R-S,S-T,R-T,R-N,S-N should be -Check short or not of Solution Check

(In case more than a few ㏀ Control box (Noise
power filter, PCB, cables)
is not - Resistance of T-N should be within 40~50Ω - Replace transformer
supplied) (Main transformer of outdoor)
2 FUSE Check - Voltage of fuse should be within 0~1V -In case of 220V,
(Protect disconnection Fuse is disconnected.
over- of FUSE  Replace FUSE
loaded (when power
current) is supplied)
Test functions
Check -Resistance of fuse should be within 0~1Ω -In case resistance is

disconnection ∞, Fuse is
of FUSE disconnected.
(when power  Replace FUSE
is not
supplied)
-173-
(a) Plus
No. Part Check

(Function) points
Basic Part
3 Nose filter Check voltage -Voltage of each connector (R-R,S-S,T-T) should - In case of 220V
(Noise emit & (When power be within 0~40V It is disconnected
protect) is  Replace noise filter
Supplied)
Troubleshooting
Guide for each
Error Code
Plus Plus II

4 Magnet Magnet switch -When check resistance of 1st coil of magnet switch, -In case resistance is
switch 1st coil resistance should be 0.47 ㏀ ∞ or 0 Ω,
Component Check
(When power is not supplied)  Replace Magnet
When magnet switch is on, voltage should be 220V switch
Electrical
(When power is not supplied)
-When voltage is not
220V, magnet switch
is melt down
- Replace magnet
switch
Solution Check
Magnet switch -While pressing green button of magnet switch, - Replace magnet
connection Voltage of each connectors should be 0V or switch
check Resistance should be 0~1Ω
(In case power (Warning: power should not be supplied)
is not supplied)
Test functions
-174-
(a) Plus
No. Part Check

(Function) points
Basic Part
5 EOCR Time, Current -Rotary switch setting should be correct
(Cut off over- Rotary (Current:30~40A, Time:5sec)
loaded switch Setting
current to
protect TIME
constant
compressor)
Current(A)
Connection -R cable and T cable should be connected each other
Troubleshooting
condition
Guide for each

Error Code
6 Outdoor MAIN PCB 2. AC 220V 19. DC12V
10. LEV drive circuit
Power connector Cooling fan
3. AC power
out circuit to
drive valves
8. JIG transmission
connector
18. 7- segment display
13. Central control signal &
on-board writing circuit
1. MICOM circuit
9. Pressure, temperature sensor
circuit
Component Check
15. FAN transmission circuit
17. Outdoor option setting switch
Electrical
14. compressor transmission circuit
16. Auto-Addressing
11. I/D↔O/D transmission

circuit
4. Power Trans In
connector
12. O/D↔O/D transmission
circuit
6. AC 220V power 5. AC voltage sensing circuit 7. Power Trans Out connector Solution Check
connector for (T-N input voltage check)
central control
Defect Check point How to check? Counter-measure

No power 2.Power terminal -Input voltage should be 220V. -Check fuse(3.15A), T-N voltage
at PCB (when power is supplied) -If resistance is 0~100Ω , replace
2.Power terminal -Input resistance should be more than PCB
a few ㏀(when power is not supplied)
7.Transformer -Output voltage should be 14V,9V -Check transformer and connection
No trans- 11.I/D↔O/D -DC voltage of connectors should be -Replace PCB, transformer and
mission 12.O/D↔O/D various (-7V~+7V) check connection points
Test functions
14.Inverter -Yellow LED should blink. -Check Main / Inverter compressor PCB
compressor and
15.Inverter fan -Green LED should blink connection points
-Check Main / Inverter fan PCB
In case 3. AC 220V -Voltage of PCB should be 220V at LGMV -Replace PCB and check connection points
PCB AC output to drive -Replace PCB and check connection points
power valves and -Output voltage should be showed as
output is below
0 others
Sensor(5V), Cooling fan(12V),LEV(12V)
-175-
(a) Plus
No. Part Check
(Function) points
Basic Part
7 Outdoor Coil resistance 1st side : 42Ω -Replace transformer
transformer (when power 2nd side :2.4Ω, 0.25Ω and check
(Supplies is not supplied) connection points
2.4 Ω 0.25 Ω
power to PCB
and
transmission)
Black : Input (220V)

Blue : Output (8.5V)
Red : Output (13V)
Troubleshooting
Guide for each
Error Code
42 Ω
In/Output 1st side : 220V (AC) -Replace transformer

voltage 2nd side : 14V, 9V(AC) and check
(when power is connection points
supplied)
Component Check
Electrical
Solution Check
Test functions
-176-
(b) Plus ΙΙ
Basic Part
2 4
Troubleshooting
Guide for each
Error Code
1 4
3
Component Check
Electrical
No. Part Check
(Function) points
1 T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within 380±10% -Check supply power
(Terminal - Voltage of 1φ(R-N,S-N,T-N) should be within 220±10%. and connection
Block, - Voltage fluctuation should be within 10V condition
Input - While stand-by and in operation,
power)
Solution Check
Check Ω - Resistance of R-S,S-T,R-T,R-N,S-N,T-N should be -Check short or not of

(In case more than a few ㏀ Control box (Noise
Test functions
power filter, PCB, cables)

is not - Replace transformer
supplied)
-177-
(b) Plus ΙΙ
No. Part Check
(Function) points
Basic Part
2 Nose filter Check voltage -Voltage of each connector (R-R,S-S,T-T) should - In case of 220V
(Noise emit & (When power be within 0~40V It is disconnected
protect) is  Replace noise filter
Supplied)
Troubleshooting
Guide for each
Error Code
3 Magnet Magnet switch -When check resistance of 1st coil of magnet switch, -In case resistance is
switch 1st coil resistance should be 0.47 ㏀ ∞ or 0 Ω,
Component Check
(Constant (When power is not supplied)  Replace Magnet
speed When magnet switch is on, voltage should be 220V switch
Electrical
compressor) (When power is not supplied)
-When voltage is not
220V, magnet switch
is melt down
- Replace magnet
switch
Solution Check
4 CT Current Current to -Check wiring

Sensor Constant
Compressor
Test functions
-178-
(b) Plus ΙΙ
No. Part Check

(Function) points
Basic Part
6 Outdoor MAIN PCB
Inverter
PCB Comm.
LED
Reset button
Inv. PCB Communication On-boarding Terminal

Terminal
Inv. Comp. High
Pr. Switch Main LEV LGMV Terminal
Sub-cooling Auto Address
LEV
Const. Comp.
High Pr. Switch Central controller
Troubleshooting
Guide for each
Error Code
Sub-cooling
sensor
Const. Comp. Liquid Valve

Inv discharge,
Inv. Comp. Liquid Valve
HEX1, HEX 2
AC Fan Power Supply
Sensors
Const. Comp.
Magnetic Switch
Hot Gas Sol. Valve
Outdoor air,
Constant Comp Heater Suction temp.,
Inv. Comp Heater
Constant comp.
discharge
Component Check
4-Way Valve
sensor
Electrical
220V Power
Input
Jig Power High Pressure

Terminal, 220V Constant Comp. Sensor
Current Sensor Low Pressure
Sensor
Communication
terminal
Defect Check point How to check? Counter-measure
Solution Check
No power 2.Power terminal -Input voltage should be 220V. -Check fuse(3.15A), T-N voltage
at PCB (when power is supplied) -If resistance is 0~100Ω , replace
2.Power terminal -Input resistance should be more than PCB
a few ㏀(when power is not supplied)
No trans- I/D↔O/D -DC voltage of connectors should be -Replace PCB and

mission O/D↔O/D various (-7V~+7V) check connection points
14.Inverter -Yellow LED should blink. -Check Main / Inverter compressor PCB
compressor and
connection points
Test functions
In case 3. AC 220V - Check Noise filter output -Replace Noise filter

PCB AC output to drive -Voltage of PCB should be 220V at -Replace PCB and check connection
power valves and LGMV points
output is Others -Output voltage should be
0
Sensor(5V), Cooling
fan(220V),LEV(12V)
-179-
3.2 How to check inverter control box?
(a) Plus
Basic Part
3
4 2
Troubleshooting
Guide for each
Error Code
1
7 5
8 6
Component Check
Electrical
No. Part Check
(Function) points
1 T/BLOCK Check voltage - Voltage of 3φ(R,S,T) should be within 380±10% - Check supply voltage
(Terminal (When power - Voltage of 1φ(R-N,S-N,T-N) should be within & connection points
block, Power is supplied) 220±10%. Check noise filter,
input) - Voltage fluctuation should be within 10V fuse
- While standby and in operation,
Solution Check
2 REACTOR Resistance of - Resistance of reactor should be within 1~3Ω - In case resistance is

(DC voltage connectors & (When power is not supplied) ∞, coil is
stabilization) connection - Voltage between terminals of reactor should be disconnected.
condition
within 0~1V (When power is supplied)  Replace reactor
Test functions
***Reactor for INV compressor Reactor for INV Fan
-180-
(a) Plus
Loc. Part Check
(Function) points
Basic Part
3 Capacitor Electric capacity. - Electricity capacity of capacitor must be - Replace capacitor
(To charge (when power is 2600~2800㎌ and the resistance of capacitors when value is more or
DC voltage not supplied) should be more than a few ㏀ less than normal spec.
for inverter
compressor)
Troubleshooting
Guide for each
DC charging - Charged voltage of between terminals of - Check input voltage and
Error Code
voltage capacitor replace capacitor
(When power is (= between IPM P-N terminal = DC link
supplied) terminals)
should be more than 450V
(At the moment of inverter compressor start)
4 INV compressor
PCB 2. Power & 3. High pressure 4. DC-Link 6. transmission 5. Checking circuit
start-relay switch & sensing & circuit to main for reverse phase
drive circuit power-relay display circuit PCB of input power
drive circuit
Component Check
Electrical
7. On-board
writing connector
1. MICOM
circuit
9. PWM driving
signal output
circuit 8. CT sensing circuit
Solution Check

No power 2.Power -Input voltage should be 220V. - Check & replace fuse(3.15A),
at PCB (when power is supplied) T-N voltage (220V)
-Input resistance should be more than a few ㏀ - If resistance value is 0~100Ω ,
(when power is not supplied) replace PCB
No 6.Transmission -Yellow LED should blink. - Check yellow LED blinks or not
transmission circuit to main - When is OFF, check transmission
Test functions
PCB with main PCB and replace

Malfunction of 9.PWM signal -Green LED should blink. - Replace PCB
inverter cable -Check IC port coupler
compressor of PWM drive
(when power is
not supplied) 1-2 Diode : 1.0V 2-3 Diode : 1.4V
Inverter Red LED -When red LED blinks. -Check error code displayed at
compressor Error displays about inverter compressor PCB main PCB
PCB Error
-181-
(a) Plus
Loc. Part Check

(Function) points
Basic Part
5 Inverter 1. MICOM circuit 10. Comm. circuit
fan PCB
9. On-boarding 2. Input circuit of 3φ &

lighting connector DC rectifying circuit
8. Heat sink
3. In/Output connector
temperature
of reactor
sensor connector
7. PWM
Troubleshooting
drive circuit 4. DC-Link output voltage
Guide for each

Error Code
6. SMPS power
circuit 5. DC-Link electrolytic
capacitor
No power 2.3φ power - Input voltage of 3φ 4 wires should be -Check supply voltage, noise
on PCB Input circuit 3φ 380V, 1φ 220V Reactor 1 filter, fuse
R, S, T, N
Component Check
- Check half wave rectifying circuit diode -Replace inverter fan PCB
(R-Reactor1: 0.6V, S-Reactor1: 0.6V:
T-Reactor1: 0.6V)
Electrical
R(+) - Reactor1(-) : 0.6V
No 10. Transmission -Yellow LED should blink. -Check yellow LED blinks or not
transmission circuit with main -When is OFF / ON continuously,
PCB
Solution Check
check transmission with main PCB
Inverter fan Red LED -When red LED blinks, error code happens -Check error code at main PCB
PCB error about inverter fan PCB
6 3φ Check voltage &

DIODE resistance of
each phases
(when power is
not supplied)

Test functions

-182-
(a) Plus
No. Part Check

(Function) points
Basic Part
7 Inverter 1. PWM signal connector
fan
IPM PCB
4. IPM
2. DC supply terminal
(DC310V)
Troubleshooting
Guide for each
Error Code
3. Outdoor unit fan connectors
Inverter fan 1.PWM signal - Check 9pin connectors - Replace cables & check
is not rotating 2.Fan DC power - DC voltage should be charged of 310V soldering condition of PCB
Component Check
3.Outdoor - While Fan operating, in case voltage of - Replace connectors & inverter
fan connector connectors(U-V,V-W,U-W) is 100~300V PCB if not charging
Electrical
→ Normal
4. IPM - Check Diode(P-N : 0.95V, - Replace inverter IPM PCB
P-U,P-V,P-W: 0.55V
N-U,N-V,N-W: 0.55V
Check DIODE(P-U : 0.5V)
Solution Check
8 IPM Check voltage
& resistance
of
each phases
(When power
is not
supplied)

Test functions

-183-
(b) Plus ΙΙ
Basic Part
4
3
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
REACTOR Resistance of - Resistance of reactor should be within - In case resistance is

(DC voltage connectors & 1~3Ω ∞, coil is disconnected.
stabilization) connection (When power is not supplied)  Replace reactor
condition - Voltage between terminals of reactor should
be within 0~1V (When power is supplied)
Solution Check
3φ DIODE Check voltage &

-In case the measured value is different from the
resistance of
table, set multi tester to resistance mode
each phases
and measure. If the value is small (0 Ω) or high
(when power is
(hundreds M Ω), PCB needs to be
not supplied) replaced.
- In case that bridge diode is damaged, check if
inverter PCB assembly (IPM) is needed to be
replaced.
Test functions
-184-
(b) Plus ΙΙ
Loc. Part Check

(Function) points
Basic Part
4 Inverter 2 220V Power input
fan PCB
700 DC
Link
Troubleshooting
DC 15V
Guide for each

Output N- Phase
Error Code
terminal Terminal
PFC
R- Phase
On-boarding
(To Diode)
terminal
R- Phase
Terminal
(From Noise
filter)
T- Phase
Terminal
(From Noise
filter)
Component Check
Inverter Error LED T- Phase Terminal (To Diode)
Inv. On-boarding terminal
Electrical
U,V,W Output terminal
11 Fan PCB Communication
11 Main PCB Communication
Main, Fan PCB Communication LED
No power 2.Power -Input voltage should be 220V. -T-N voltage (220V)

at PCB (when power is supplied)
-Input resistance should be more than a few -If resistance value is 0~10,
㏀ (when power is not supplied) replace PCB
Solution Check
No transmission 10.Transmissio -LEDs should blink. - Check LED blinks or not
(Main PCB) n circuit to - When is OFF, check
(Fan PCB) main, fan PCB transmission with main, fan
PCB
Inverter 12. PWM LED -When red LED blinks. -Check error code displayed
compressor PCB PWM is normal at main PCB
Error
Test functions
-185-
(b) Plus ΙΙ
Loc. Part Check

(Function) points
Basic Part
4 Inverter
fan PCB
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
DC link DC link Checking DC Link in inv. PCB
voltage check connection
and IPM between Inverter
check* and Fan PCB
* IPM check: [CN CD_LINK]

After
disconnecting
all connector
Solution Check
No 10. Transmission -Yellow LED should blink. -Check yellow LED blinks or not
transmission circuit with -When is OFF / ON continuously,
Inverter PCB check transmission with main
PCB
Test functions
Inverter fan Red LED -When red LED blinks, error code happens -Check error code at main PCB
PCB error about inverter fan PCB
-186-
3.3 How to check Multi V Space control box?
* MUTLI V SPACE 10HP C/BOX
Basic Part
10 11
10 11 12 6 12
9
5 8 7
7 8 5
Troubleshooting
Guide for each
4
Error Code
3 6 3
2
1 1
2
Component Check
Electrical
N2(COMP B,FAN B) N1(MAIN control + COMP A,FAN A)
NO Name Function NO Name Function
1 T/BLOCK 3 phase 4 line power input 1 T/BLOCK 3 phase 4 line power input
Excessive electric blockade

2 FUSE 2 FUSE Excessive electric blockade(30A)
(30A)
3 Noise filter Block and discharge noise 3 Noise filter Block and discharge noise
Solution Check
LOGIC control of the whole
- - - 4 MAIN PCB
product
5 FAN PCB BLDC FAN control 5 FAN PCB BLDC FAN control
6 COMP PCB BLDC COMP control 6 COMP PCB BLDC COMP control
Switching degauss ,(COMP Switching degauss ,(COMP

7 IPM 7 IPM
output) output)
3 phase power commutation 3 point phase commutation

8 DIODE 8 DIODE
degauss (+) degauss (+)
Test functions
9 TRANSE Supply MAIN PCB power
DC voltage stabilization and DC voltage stabilization and

10 REACTOR 10 REACTOR
power factor beveling power factor beveling
DC voltage recharge DC voltage recharge

11 CAPACITOR 11 CAPACITOR
(COMP,FAN) (COMP,FAN)
12 Magnet S/W BLDC COMP switch 12 Magnet S/W BLDC COMP switch
-187-
Multi V SPACE COMP PCB
2.CN09 3.CN05 4.CN01
Basic Part
[COMP>FAN[3point sensor] [power supply START RELAY]
Communication]
1.CN06
[MAIN>COMP
Communication]
12. LED01,02K
5.CN04
Troubleshooting
11. Function key [high pressure switch
Guide for each

& Power-Relay]
Error Code
6.Power supply
Component Check
9.CN02 8.CN IIPM 7.CN GATE1,2
[DC LINK sensor]
Electrical
10.CN14
[COMP output sensor]
Monitoring
Situation How to check? Counter-measure
Location
PCB power does not 4.CN01 -input voltage must be 220V (power on) -LINE FUSE(3.15A)
turn on (CH52) manage after checking input
-input resistance is over ㏀.(power off) voltage 220V
-replace PCB if the resistance is
Solution Check
0~100Ω
Communication does 1.CN06 -yellow LED(LED01,02K)must flick. -check communication and FAN
not work 2.CN09 PCB and MAIN PCB if the yellow
(CH52) LED is flick or OFF (check
connection and replace PCB)
COMP malfunction 10.CN14 -constant COMP output U(-),V(-),W -replace after checking PCB and
COMP if the difference is over 2A
9.CN02 -DC voltage within 470V~520V
-replace after checking CAPACITOR
8.CNIPM -check connection status and PCB
Test functions
7.CN_GATE
(CH21 Replace and check motor and
connection
CH22
CH23)
Deficiency error 3.CN05 -3 point power line (noise filter latter part) - Readjust and Replace after
(CH54) over 380V checking FUSE, input power ,
connection line
-188-
Multi V SPACE BLDC FAN PCB
4.SW_SEL 6.CN_COMM
[louver 5.SW_DIR [MAIN PCB>FAN PCB] :5,6,8HP
selection] [FAN direction] [FAN>COMP PCB] : 10HP
LED01M : PWM Enable
Basic Part
LED02M : display error
7.CN_POWER2
3.Power supply [louver power supply]
LED01K
(FAN>INV
communication)
8.SW01M,02M,03M
[PCB JIG check]
Troubleshooting
Guide for each
9.CN_WIRTE
Error Code
[on boarding light]
10.CN_M1S,M2S
2.CN_DC LINK [louver signal input]
[DC power
11.CN_SENSOR
supply sensor)
[FAN signal input]
1.CN_POWER
[PCB power 12.CN_MOTOR1,2
supply) [louver signal output]
13.CN_FAN
Component Check
[FAN signal output)
Electrical
Power does 1.CN POWER -AC voltage measure 220V -Input voltage (220V)
not turn on
3. Power supply (CH105) - ZNR01D( barrister ),FUSE burn out -Replace related parts
checkup
FAN motion 2.CN_DC LIINK -DC 470V~520V displays - Check and replace CAPACITOR
disabled -DC 380V and above are normal - Replace PCB
13.CN_FAN(CH106) - U,V,W electric flow measurement Check up and replace connection

11.CN_SENSOR(CH67) stabilize and motor
-Check connectors
Solution Check
communicat 6. CN-COMM -Flick LED01K -Check PCB power supply(220V)
ion does (CH105) - check connector and PCB (power -Check and replace connector and
not work supply ,communication) PCB
Louver does 4.SW_SEL -Check if connector is connected - connect connectors (if there are no
not work louver)
7.CN_POWER2 -DC24V display check -Check and Replace trance and

power supply
10.CN_M1S,M2S -Connection status check -Check and replace louver motor

and connection part
12.CN_MOTOR1,2 - Connection status check - Check and replace louver motor

and connection part
Test functions
*BLDC motor monitoring method

1 2
3 4 Ha(4),Hb(3) - Gnd(2) : 24MOhm
Ha(4),Hb(3) - Vcc(1) : 11KOhm
Vcc Gnd
Hb Ha
-189-
3.4 How to check indoor unit PCB?
3.CN_FLOAT
[Drain pump
13.CN_POWER 1.CN_MOTOR 2.CN_CC3 sensor]
[power supply_220V] [indoor motor] [DRY CONTACT
boarding]
Basic Part
4.CN_OPTION
[additional function]
5. Sensing part
[pipe]
6.CN_REMO
[remote control
power &
communication]
Troubleshooting
7.CN_HVB
Guide for each

12.CN_DRAIN [plasma]
Error Code
[Drain pump 11.CAPACITOR 9.CN_VANE1,2 8.CN_DISP
Output part_220v] [internal$ external]] [louver operation] [reception part PCB
10.CN_LEV connection port]
[indoor LEV operation]
* Outdoor unit communication PCB front side Outdoor unit communication PCB backside
* When there is
communication error(U01Y)
1 8
2 7
3 6
Component Check
14.CN_A5
[indoor PCB 4 5
connection] DIODE MODE measurement
Electrical
8-1,2,3,4 : 1.2V
5-1,2,3,4 : 0.7V
Communication
Connection (A,B)
Monitoring
Situation How to check? Counter-measure
Location
PCB, remote control 13.CN_POWER -input voltage must be 220V.(power on) -manage and check input voltage 220V
power does not come - Barrister (ZNR01N),FUSE,,PCB check -replace and check relate parts
on
Communication does 14.CN_A5 -check connection -readjust and check connection

not work
Solution Check
communication -Check connection PCB latter U01Y -Replace and check IC(DIODE)
PCB -- green LED flick (flick initially) -Replace after checking communication
PCB and indoor unit PCB power supply
Outdoor unit motor 1.CN_MOTOR -Error CH10(FAN LOCK) when it does not -replace and check motor and
does not work operate after remote control operation connection
11.CAPACITOR -DC 310V is recharged Replace CAPACITOR
Outdoor unit sensor 5. sensor -is LG MV sensor value normal? -replace and check connection and
error (CH01,02,06) sensor part
Outdoor unit front 8.CN_DISP -check indoor unit front panel LED -reception PCB and connection part
panel reception defect operation reception PCB and connection part
and remote control - Wireless remote control and forced
Test functions
does not work operation switch operation
Indoor unit leakage 12.CN_DRAIN -DRAIN display AC 220V -replace PCB

3.CN_FLOAT -CH04 display or DRAIN operation - Replace DRAIN pump and check
connection status
CH03 and remote 6.CN_REMO -When remote control operate and when -remote control, indoor unit PCB check
control does not work indoor unit operation -eliminate noise and check
--intermittent CH03 occurrence automatic communication line connection status
ON/OFF check remote control SETTING
-190-
3.5 How to check other electric components?
(a) Plus
Name Check
Check points
Basic Part
Loc.
Display Outdoor unit

Value of main PCB
main display Value Main PCB
PCB in (At the
outdoor moment that 4X Main model name
unit power is 50 Sub1(when connected)
supplied) 50 Sub2(when connected)
XX Total operation capacity in Hp

(Ex: 20 Hp  20)
Troubleshooting
Guide for each
25 Normal state
Error Code
Others : PCB checking mode
22 In case of R22 refrigerant
R410A: 41
Component Check
Electrical
Outdoor
sub unit
PCB display
Value Sub PCB
(When power
is supplied) LED 8 7 6 5 4
Solution Check
display
condition) LED 3
LED 2
LED 1
LED1(blinking): Display normal micom condition

LED2, 3(On): Back-up for left/right compressor
LED4 : reserved
LED5(blinking) : Communicate with main
Test functions
LED6(On) : Reverse connection at sub unit

LED7(On) : Right compressor is in operation
LED8(On) : Left compressor is in operation
-191-
(a) Plus
Name Check point
Outdoor unit ◈ Dip switch Setting ◈
Basic Part
PCB DIP
switch
8 7 6 5 4 3 2 1
ON
1. Main unit
DIP RE Function Method / description

s/w SET
Troubleshooting
Guide for each
Error Code
1 X Cooling operation control No. 1 ON push RED button 3 times for 3 sec.
 display 01, 0F by turns (#1 indoor unit OFF)
 Push BLACK button for 3 sec.
 display 01,0P by turns
 A few sec. later display 01, 0N by turns (#1 indoor unit ON)
 Push RED button for 1 sec.
 display 02, 0F by turns (#2 indoor unit OFF)
 (go on…)
1 O SAVE MODE No.1 ON  RESET

/ Target high pressure down, target low pressure up
Component Check
2 O CAPACITY UP No.2 ON  RESET
/ Target high pressure up, target low pressure down
Electrical
1,2 X Heating operation No.1, No.2 ON
control / Same process as cooling operation
3 O Inverter compressor BACKUP No.3 ON  RESET

operation / while inverter compressor failure, operate more than indoor unit
capacity (SINGLE:70K,SERIES:110K)
4 O Constant No.4 ON  RESET

compressor 1 BACKUP operation / while constant compressor failure, operate more than indoor unit
capacity (SINGLE:70K,SERIES:110K)
3,4 O MAIN UNIT BACKUP No.3, No.4 ON  RESET / when MAIN unit failure
5 O Cooling operation LOCK No.5 ON  RESET / locking cooling operation mode Solution Check
6 O Heating operation LOCK No.6 ON  RESET / locking heating operation mode
7 X Forced oil return operation No.7 ON  Push BLACK button for 2 sec.  display 01(Oil return)
2. Sub unit
DIP RE Function Method / description
s/w SET
3 O Constant compressor 1 BACKUP No.3 ON  RESET

operation / while constant compressor1(left) failure,
operate more than indoor unit capacity (SINGLE:70K,SERIES:110K)
Test functions
4 O Constant compressor 2 BACKUP No.4 ON  RESET

operation / while constant compressor2(right) failure,
operate more than indoor unit capacity (SINGLE:70K,SERIES:110K)
5 O SUB1(2UNIT) No.3 ON  RESET / SUB1 recognition (2UNIT)
6 O SUB2(3UNIT) No. 4 ON  RESET / SUB2 (3UNIT)
5,6 O SUB3(4UNIT) No.3, No.4 ON  RESET / SUB3 recognition (4UNIT)
-192-
(b) Plus ΙΙ
Name Check
Check points
Loc.
Basic Part
Display Outdoor unit
Value of main PCB
main display Value
PCB in (At the
outdoor moment that
unit power is
supplied)
Troubleshooting
Guide for each
Error Code
Component Check
Initial setup
There are 4 initial setup steps before running.
Electrical
All DIP switch setting must be completed before initial setup.
1) Step 1 : factory setting value display
Factory setting value is displayed in 7 segment on PCB for 24sec.
All dip switches must be set properly before step 1.
Solution Check
Test functions
Example) 30HP, R410A

63 ➔ 63 ➔ 63 ➔ 30 ➔ 2 ➔ 25
➔ 41
-193-
Error Code
-194-
(b) Plus ΙΙ
(b) Plus ΙΙ
Name Check point
Outdoor unit
◈ Dip switch Setting ◈
Basic Part
PCB DIP
switch
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON
8 7 6 8 7 6
OFF
1. Main unit
Troubleshooting
No. RESET Function Dip Switch
Guide for each

Error Code
1 Standard Setting All Off
2 0 Short Pipe length No.1 ON

Target high pressure down, target low pressure up
3 0 Long pipe length No.2 ON

Target high pressure Up, target low pressure down
4 0 Longest Pipe length No.1, No.2 , ON
5 X Refrigerant Auto Charging No.1, No.2, No.7 ON
Component Check
6 X Refrigerant checking No.1, No.2, No.7, No.14 ON
Electrical
7 0 Forced Cooling operation No.5 ON
8 0 Forced Heating operation No.6 ON
9 0 Dry Contact No.5, No.6 ON
10 0 Snow No.8 ON
11 X Forced defrosting No.9 ON
12 0 Snow + Forced defrosting No.8 , No.9 ON
Solution Check
13 0 Outdoor unit fan low static No.12 ON
pressure compensation
14 0 Outdoor unit fan low static No.13 ON

pressure compensation
15 0 Night low noise No.12, No.14 ON
16 X Pump down No.10 ON
17 X Forced Oil return No.7 ON
18 X Vacuum mode No.11, No.14 ON

Test functions
-195-
(b) Plus ΙΙ
Name Check point
Outdoor unit ◈ Dip switch Setting ◈
Basic Part
PCB DIP
switch
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON
8 7 6 8 7 6
OFF
2. Settings of slave outdoor unit
Troubleshooting
Guide for each
Error Code
1 0 Slave 1 No.5, No.7, ON
2 0 Slave 2 No.6, No.7, ON
3 0 Slave 3 No.5, No.6, No.7, ON
3. Settings of corresponding outdoor unit
Component Check
Electrical
1 0 Inverter comp. back-up No.3 ON
2 0 Unit back-up No.4 ON
3 X Pump out No.10, No.14, ON
Solution Check
Test functions
-196-
(b) Plus ΙΙ
Name Check location and method
Inverter compressor drive current (When compressor is starting)
Basic Part
- Driving current fluctuation of Inv. compressor should be less than 2A(Plus)
Troubleshooting
Guide for each
Check current of U phase Check current of V phase Check current of W phase
Error Code
- Driving current fluctuation of Inv. compressor should be less than 2A(Plus II)
Component Check
Electrical
Coil resistance of compressor (When power is not supplied)
Compressor
Check resistance of INV,constant compressor

INV, const. speed comp. resistance :INV COMP → 1.2Ω±10%(Plus),
U-V: 1.16±7%Ω, V-W: 1.19±7%Ω, W-U: 1.21±7%Ω(plus II)
:Constant speed COMP : (U-V)1.96Ω/(V-W)1.91Ω/(U-W)1.99Ω±10%)
Solution Check
Resistance between U-W Resistance between V-W Resistance between U-V
Insulation resistance of compressor (when power is not supplied)
Check insulation resistance of constant compressor

(inverter compressor : a few 2㏁↑,constant compressor : a few ㏁↑)
Test functions
-197-
(C) Plus, Plus ΙΙ
Name Check location and method
Check outdoor unit LEV
Basic Part
① - ③ : around 300Ω ② - ④ : around 300Ω ① - ⑤ : around 150Ω
Troubleshooting
Guide for each
Error Code
③ - ⑤ : around 300Ω ② - ⑥ : around 300Ω ④ - ⑥ : around 150Ω
Component Check
Measurement of outdoor unit LEV coil resistance
Electrical
LEV
Outdoor unit main LEV Outdoor unit sub cooling LEV Indoor unit LEV
Solution Check
① - ③ : around 300Ω ① - ③ : 104 ± 6Ω ① - ③ : around 300Ω
② - ④ : around 300Ω ② - ④ : 104 ± 6Ω ② - ④ : around 300Ω
① - ⑤ or ③ - ⑤ : around 150Ω ① - ⑥ or ② - ⑥ or ① - ⑤ or ③ - ⑤ : around 150Ω

Test functions
② - ④ or ④ - ⑥ : around 150Ω ③ - ⑥ or ④ - ⑥ : 52 ± 3Ω ② - ④ or ④ - ⑥ : around 150Ω
-198-
Basic Part Guide for each Solution Check Test functions
Error Code Component Check
Solution
Check
-199-
4
.
Central control Structure
Basic Part
3rd part
LonTalk/ BACnet
BMS
Ethernet
Gateway 2-1 2-2 (TCP/IP) 1
Troubleshooting
Guide for each
Error Code
CNU AC Smart SCC
Server ACP D.C
LonWorks BACnet
EIA-485
2-3 3
Telemetering apparatus
PI485 Interface PDI Dry contact
Component Check
UART
Electrical
LGAP
LG’s A/C
Outdoor unit
Indoor unit
Multi V Multi MPS Single CAC Ventilator

Remote
controller
Solution Check
Test functions
-200-
A. Installation guide
Basic Part
1. Multi-V + Simple Central Controller
2. CAC(Single,Multi) + Simple Central Controller
3. Multi-V + CAC + Simple Central Controller
Troubleshooting
Guide for each
Error Code
4. Eco-V + Simple Central Controller
5. Multi-V + ACP + Simple Central Controller
Component Check
6. Multi-V + CAC + ACP + Simple Central Controller
Electrical
7. Multi-V + Eco-V + CAC + ACP + Simple Central Controller
8. Multi-V + Eco-V + AC Manager + ACP
Solution Check
Test functions
-201-
■ Multi-V+ Simple central controller. 1ea [ 1 Line wiring ]
Basic Part
PI485
Rotary DIP Indoor unit
switch switch Controller DIP Outdoor – Indoor unit connection address
setting setting switch setting
setting (*)
[00] … [03]
ODU
Troubleshooting
[0] 1,2 ON [04] … [07]
Guide for each

Series 2
Error Code
&
IDU [09] … [0B]
Series 2
No need [0C] … [0F]

PI485
Component Check
Electrical
(*): incase of using external PI485. See page 257
▣ Process
① Indoor address Setting
※ must be not duplicated
② Install PI485, Wiring RS485 line(Bus Method)
③ PI485 Dipswitch Setting Solution Check
Power on
※ Check PI485 Red LED blinking. It must equal to number of connected I/U
If different, Check outdoor Auto_addressing
④ Setting Rotary switch on Simple central controller.
※ same to the 1st digit of connected indoor unit address
⑤ Setting Dip switch on Simple central controller
Test functions
Turn the power ON:

After 3 Minutes (Searching Time)
Simple central controller must recognize all indoors
(you can check by pushing total On + Total Off + 13)
※ If not recognize all indoors, repeat upper process
-202-
Basic Part
PI485
setting (*)
[00] … [03]
ODU
Troubleshooting
[0] 1,2 ON Master [04] … [07]
Guide for each

Series 2
Error Code
&
IDU
[10] … [13]
Series 2
[1] 2 ON Slave
No need [14] … [1F]
PI485
Component Check
Electrical
PI485
setting (*)
Solution Check
[00] … [03]
[0] 1,2 ON Master ODU [04] … [07]

Series 2
&
IDU [10] … [13]
Series 2
[1] 2 ON Slave
Test functions
[14] … [1F]
No need
PI485
[20] … [23]
[2] 2 ON Slave
[24] … [2F]
(*): incase of using external PI485. See page 257 -203-

Basic Part
PI485
setting (*)
[00] … [03]
ODU
Troubleshooting
[0] 1,2 ON Master [04] … [07]
Guide for each

Series 2
Error Code
&
IDU [10] … [13]
Series 2
[1] 2 ON Slave
[14] … [1F]
No need
PI485
[20] … [23]
Component Check
[2] 1,2 ON Master
[24] … [2F]
Electrical
Solution Check
Test functions
-204-
■ CAC (Multi/ Single) + Simple central controller. 1ea
Basic Part
PI485
setting
[00]
[01]
[02]
Troubleshooting
Guide for each
[0] 1,2 ON
Error Code
PMNFP14A0, [03]
[04]
[05]
[1,4,5 ON]
or
[06]
[2,4,5 ON]
Component Check
(*)
Max. 16 indoor unit
Electrical
(*) The DIP switch setting must follow to below table:
Solution Check
Test functions
-205-
■ Multi V + CAC (Multi/ Single) + Simple central controller. 2ea
Basic Part
Rotary DIP PI485 Indoor unit
Outdoor – Indoor unit
switch switch Controller DIP switch address
connection
setting setting setting setting
Multi V ODU [00] … [03]

Series 2
&
Troubleshooting
Master
Guide for each

[0] 1,2 ON
Multi V IDU
Error Code
Series 2
[04] … [07]
No need
[1] 2 ON Slave PI485
[10]
PMNFP14A0, [11]
[12]
Component Check
[1,4,5 ON]
Electrical
[13]
or
[14]
[15]
[2,4,5 ON]
(*)
[16]
Solution Check
(**) The DIP switch setting must follow to below table:

Test functions
-206-
■ Ventilator + Simple central controller. 1ea
Basic Part
PI485
setting (*)
[00]
Troubleshooting
[0] 1,3 ON PHNFP14A0
Guide for each

Error Code
[04]
[3,4 ON]
[09]
[0C]
Component Check
Electrical
▣ Process
① Dipswitch setting on Eco-V Main PCB, Power On
② Eco-V address Setting.
③ Install PI485, Wiring RS485 line (Bus Method)
④ PI485 Dipswitch Setting Solution Check
Power on
※ Check PI485 Yellow LED blinking.
⑤ Setting Rotary switch on Simple C.C.
⑥ Setting Dip switch on Simple C.C. and Power on.
⑦ wait for 3 Minute (Searching Time)
(you can check by pushing total On + Total off + 13)
Test functions
-207-
■ Ventilator + Simple central controller. 2ea [1 line wiring]
Basic Part
PI485
setting (*)
[00]
Troubleshooting
[0] 1,3 ON Master PHNFP14A0
Guide for each

Error Code
[0F]
[3,4 ON]
[10]
[1] 3 ON Slave
[1F]
Component Check
Electrical
▣ Process
① Dipswitch setting on Eco-V Main PCB, Power On
② Eco-V address Setting.
③ Install PI485, Wiring RS485 line (Bus Method)
④ PI485 Dipswitch Setting Solution Check
Power on
※ Check PI485 Yellow LED blinking.
⑤ Setting Rotary switch on Simple C.C.
⑥ Setting Dip switch on Simple C.C. and Power on.
⑦ wait for 3 Minute (Searching Time)
(you can check by pushing total On + Total off + 13)
Test functions
-208-
■ Ventilator + Simple central controller. 2ea [2 line wiring]
Basic Part
PI485
setting (*)
[00]
PHNFP14A0
Troubleshooting
[0] 1,3 ON Master
Guide for each

Error Code
[0F]
[3,4 ON]
[10]
[1] 1,3 ON Master
[1F]
Component Check
Electrical
Solution Check
Test functions
-209-
■ Air conditioner + Ventilator
+ Simple central controller [1 line wiring]
Basic Part
PI485
setting (*)
[00] … [03]
PMNFP14A0,
Troubleshooting
[0] 1,3 ON PMNFP14A1
Guide for each

[04] … [07]
Error Code
[1,4,5 ON]
PHNFP14A0 [08]
[0C]
[3,4 ON]
Component Check
Electrical
■ Air conditioner + Ventilator
+ Simple central controller [2 line wiring]
PI485
Solution Check
setting (*)
[00] … [03]
PMNFP14A0,
[0] 1,2 ON PMNFP14A1
[04] … [07]
[1,4,5 ON]
Test functions
PHNFP14A0 [00]
[0] 1,3 ON
[0F]
[3,4 ON]
-210-
■ Multi-V+ ACP + Simple central controller. [ 1 Line wiring ]
Basic Part
PI485
setting (*)
[00] … [03]
ODU
Troubleshooting
[04] … [07]
Guide for each

Series 2
Error Code
&
IDU
[10] … [13]
Series 2
[0] 2 ON Slave
No need [14] … [1F]
PI485
Component Check
[1] 2 ON Slave
Electrical
PI485
setting (*)
Solution Check
[00] … [03]
ODU
[0] 2 ON Slave [04] … [07]
Series 2
&
IDU
[10] … [13]
Series 2
No need [14] … [1F]

Test functions
PI485
[1] 2 ON Slave

■ Multi-V + CAC + ACP + Simple central controller. [ 1 Line wiring ]
Basic Part
PI485
setting (*)
ODU
Series 2 [00] … [03]
&
IDU
Troubleshooting
[04] … [07]
Guide for each

Series 2
Error Code
No need
PI485
PMNFP14A0,
[0] 2 ON Slave
[10]
[11]
[1,4,5 ON]
[12]
or
Component Check
[1] 2 ON Slave [13]
[2,4,5 ON]
Electrical
(*)
■ Multi-V+ CAC + ACP + Simple central controller. [ 2 Line wiring ]
PI485
setting (*)
[00] Solution Check
[01] … [0F]
PMNFP14A0,
[0] 2 ON Slave
[1,4,5 ON]
or [10] … [1E]
Test functions
[2,4,5 ON] [1D] … [1F]

(*)
[1] 2 ON Slave

■ Multi-V + CAC + Vent + ACP + Simple central controller.
[ 1 Line wiring ]
Basic Part
PI485
setting (*)
PMNFP14A0, [00] … [03]
Troubleshooting
[04] … [07]
Guide for each

[1,4,5 ON]
Error Code
or [08]
[09]
[2,4,5 ON] [0F]
[0] 2 ON Slave
(*)
[10]
PHNFP14A0
Component Check
[1] 3 ON Slave
[3,4 ON]
Electrical
PI485
setting (*)
Solution Check
PMNFP14A0,
[00]
[1,4,5 ON] [01] … [0F]

or
[0] 2 ON Slave
[2,4,5 ON]
(*)
Test functions
[10] … [1E]
PHNFP14A0
[1D] … [1F]
[1] 3 ON Slave
[3,4 ON]

-214-
■ Power Distribution Indicator
■ AC Manager system
Connect to LG Central controller (setting PDI in “SLAVE” mode)
Basic Part
Scene 1 Outdoor units are installed nearby each other
Port 1 485 line
Port 4 3Ø 380V
Troubleshooting
Guide for each
Error Code
…
PI485
…
Watt meter PDI

CN_OUTFAN
Component Check
Electrical
Solution Check
Test functions
-215-
Not connect to Central controller
Scene 2 Connected indoor unit per. Outdoor unit less than 16
Basic Part
(setting PDI as Unit)
3Ø 380V
Troubleshooting
…
Guide for each

Error Code
In-out door comm.
…
line
Watt meter PDI
Component Check
Electrical
Scene 3 Connected indoor unit per. Outdoor unit more than 16
(setting PDI as Master)
Use PMNFP14A1 PI485 Gateway
Solution Check
3Ø 380V …
PNF-P14A1M
Master 모드
In-out door comm.
…
Test functions
line
전력량계 전력표시기
-216-
B. Trouble shooting
Basic Part
Case A1: Several indoor unit error (242)
Case A2: all I/U of the same O/U error (242)
Case A3: all I/U of the same 485 line error (242)
Case A4: indoor unit can’t be controlled by S.C.C but ACP
Troubleshooting
Guide for each
Error Code
Case B1: impossible to access ACP Web
Case B2: ACP access is not stable
Case C1: Operation mode auto-change

Lock function auto-release
Case D1: some indoor acc. Pwr. is displayed = 0
Component Check
Case D2: all indoor acc. Pwr. in one group are displayed = 0
Electrical
Case D3: Value on ACP and PDI doesn’t match
Case D4: Value on ACP and Watt meter doesn’t match
Case E1: Ventilator communication error
Solution Check
Test functions
-217-
I. Phenomenon:
Indoor units display error (242), can not control by
simple central controller.
Basic Part
Troubleshooting
Guide for each
Error Code
II. Reason and Solving:
Component Check
Electrical
Indoor units
(242) error
address wrong setting Y

check and setting
(duplicate, not in-
address again
range)
N
Solution Check
indoor unit power Y check power (220V)
supply (not plug-in,
and re-plug in
fuse blow)
N
indoor unit main PCB Y

change main PCB
failure
Outdoor unit Auto- Y Outdoor unit Auto-

Test functions
addressing fault addressing
-218-
■ Address wrong setting
Basic Part
ACP can not control a address duplicated indoor unit (20)
r
rro
E
20 21 22 23
Troubleshooting
Guide for each
Error Code
10 11 12 20
r
rro
E
Component Check
Electrical
20 24
Address re-setting (+ central controllers power reset)

Solution Check
Test functions
-219-
■ Indoor main PCB power failure:
Basic Part
Check if the power cord is not plugged in or Fuse is blown out
r
rro
Troubleshooting
E
Guide for each

Error Code
20 21 22 23
10 11 12 24
Component Check
Electrical
power cord is not plugged
Solution Check
Fuse blown out

Test functions
-220-
■ Indoor main PCB failure:
Basic Part
A failure PCB doesn’t sound “Bip” when reset main power.
Check and replace with new one with proper P/No.
You need to set the indoor unit address and do Auto-addressing
on Outdoor unit again.
Troubleshooting
r
Guide for each

ro
Error Code
E r
20 21 22 23
10 11 12 24
Component Check
Electrical
220V
Solution Check
Buzzer
Test functions
-221-
■ Outdoor unit auto-addressing failure:
Basic Part
Check if the Auto-addressing function return correct number of
indoor units.
Incase of incorrect, check the connection line between O/U and
I/U, and indoor unit main PCB.
Troubleshooting
Guide for each
Do auto-addressing on this outdoor unit
Error Code
r
rro
E
20 21 22 23
Component Check
Electrical
10 11 12 24
Press the switch of the Display number of

outdoor unit (SW02V) connected indoor unit
for 5 seconds.
Solution Check
Test functions
Numbers of indoor unit connection set whose

addressing is completed are indicated for 30seconds
on 7-segment LED of the outdoor unit PCB.
(refer to data-book)
-222-
I. Phenomenon:
Basic Part
All I/U that connected to the same O/U display error
(242), can not control by central controller.
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Same Outdoor unit

Solution Check
In this case, the reasons mostly come from PI485
Indoor units
(242) error
Y PI485’s DIP switch

PI485 DIP switch
re-setting
wrong setting
N
Test functions
Y
PI485 failure Change PI485
N
PI485’s comm. cable Y
wiring failure re-wiring
(Bus_A, Bus_B)
-223-
■ PI485 DIP switch wrong setting (*)
Basic Part
The DIP switch wrong setting cause wrong communication
between controller and indoor units.
correct and reset PI485 (press Reset button)
Check this PI485’s DIP switch
Troubleshooting
Guide for each
r
Error Code
rro
E
20 21 22 23
10 11 12 24
Component Check
Electrical
Reset button
PMNFP14A0,
PMNFP14A1
Multi V, Plus [1,4,5 ON]

MPS inverter
PMNFP14A0(1)
Solution Check
PMNFP14A0,
[2,4,5 ON]
Multi MPS (*)
PMNFP14A0(1)
Test functions
LED2G(Yellow), LED3G(Orange)
Normal : LED blinks continuously

-224-
■ PI485 failure (*)
Basic Part
The LED doesn’t blink at all (with power supplied)
replace with new one with proper type.
(plz report to the QA team also)
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-225-
■ 485 wiring failure:
Basic Part
Check if the connection to PI485 open or in bad condition.
re-wiring
Check this connection
Troubleshooting
Guide for each
Error Code
r
rro
E
20 21 22 23
Component Check
Electrical
10 11 12 24
Solution Check
Connection is open
Test functions
In bad condition
-226-
I. Phenomenon:
Basic Part
Indoor units display error (242), can’t be
controlled by central controller.
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Indoor units Solution Check

(242) error
Wrong connection to Y
controller Re-wiring
(Bus_A, Bus_B)
N
Other Master device Y Set to Slave and re-set

Test functions
exist ? system.
485 line short-circuit Y

Change the line
or open?
-227-
■ Wrong connection to central controller
Basic Part
RX LED always
bright
u lt
Fa
Troubleshooting
Guide for each
Error Code
TX ↔ Bus_B
u lt
Component Check
RX ↔ Bus_A Fa
Electrical
Solution Check
Test functions
Rewiring
-228-
■ Other Master devices exist (Simple central controller)
Basic Part
when connect to central controller, Simple central controller must
be set as Slave.
Troubleshooting
Guide for each
Error Code
20 21 22 r 23
rro
l E
Master Al
10 11 12 2D
Component Check
Electrical
u lt
Fa
1st OFF- Slave
Solution Check
DIP switch: 1st ON- Master
+ reset power of all controllers Test functions
-229-
■ Other Master devices exist (Power Distribution Indicator)
Basic Part
when connect to central controller, Power Distribution Indicator
must be set as Slave.
Troubleshooting
Guide for each
r
Error Code
20 21 22 23
rro
l E
Al
10 11 12 2D
Master Slave
Component Check
Electrical
Solution Check
Test functions
-230-
Case A4: indoor unit can’t be controlled by S.C.C
but ACP
I. Phenomenon:
Basic Part
Indoor unit can’t be controlled by S.C.C but ACP

PI485 (of I/U 2D) doesn’t connect to the proper S.C.C
(Gr.2)
Re-wiring
Troubleshooting
Guide for each
Error Code
Indoor units can’t
be controlled by
S.C.C but ACP
Not physically Y
connected to proper Re-wiring
S.C.C
Component Check
Electrical
Office
20 21 22 23
10 11 12 2D
Restaurant Solution Check
Office
20 21 22 23
Test functions
10 11 12 2D
Restaurant
-231-
I. Phenomenon:
Basic Part
Can not access ACP web.
Troubleshooting
Guide for each
Error Code
Ping test
NG
Component Check
Electrical
Problem often comes from ACP IP setting or LAN

cable.
Impossible
to access
ACP web
ACP’s IP address
Y
Re-setting and reboot Solution Check
wrong setting ACP
ACP power supply Y

Plug-in or change
failure ?
N
Y
Test functions
LAN cable failure?

Change the line
(cross/ direct/ 80m)
MAC address not Y

Do registration
registered
-232-
ACP IP wrong setting
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
■ ACP IP re- setting
ACP IP address 192.168.2.200 192.168.1.200
PC IP address 192.168.1.212 192.168.1.212
[Before] [After]
Solution Check
Test functions
[ACP rebooting]
[refer to manual]
-233-
Wrong LAN cable type cause connection failure.
Basic Part
Troubleshooting
Guide for each
Hub
Error Code
Component Check
Electrical
The cross cable should be within 80m length.
Solution Check
Test functions
-234-
Not register ACP’s MAC address.
Basic Part
PC1 can’t access ACP
PC1
Register ACP’s MAC address to
G/W1
administrator.
Troubleshooting
165.186.1.28
Guide for each

Error Code
G/W 165.186.1.0
PC2
G/W2
ACP Hub
Component Check
165.186.2.29 165.186.2.30
Electrical
G/W 165.186.2.1 G/W 165.186.2.0
MAC: xxx xxx xxx
Solution Check
Test functions
-235-
I. Phenomenon:
Basic Part
ACP Web access is not stable (sometimes was
denied) or very slow.
Troubleshooting
Guide for each
Error Code
[Access is denied] [Access is slow]
Component Check
Electrical
[Ping test to ACP]
ACP Web Solution Check

access is
not stable
Y
ACP’s IP address Re-setting and reboot
duplicated? ACP
ACP is located near Y

Test functions
UPS or high voltage Move to other place

source ?
N
Y
Power supply failure? Change other one
-236-
Duplicated IP between ACP and other devices cause access
Basic Part
instable.
165.186.2.28
Troubleshooting
School LAN
Guide for each

Error Code
Hub
165.186.2.29
u lt
Fa
ACP
165.186.2.29 165.186.2.30
IP address duplicate
Component Check
Electrical
■ ACP IP address re- setting
Solution Check
[refer to manual]
Test functions
[ACP rebooting]
-237-
Duplicated IP check method:
Basic Part
1. ACP and PC is in same Router/Hub/Switching equipment
in DOS window
c:\> arp –a [Enter]
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Check to ACP’s MAC Address.
If this number is not the ACP’s MAC address
There is other device using same IP address (duplicate)
※ Note : ACP’s MAC address Check Method

by using ACP’s LCD & key, You can select information
then you can see the MAC address
(refer to the ACP manual)
Solution Check
2. ACP and PC is not in same Router/Hub/Switching equipment
Request Network Manager about routing table, ARP table and

MAC address
Test functions
-238-
Instable access can caused by noise from other equipment.
Basic Part
■ By high voltage source
High voltage transformer
0.5m
Troubleshooting
Guide for each
ACP
Error Code
Server room Machinery room
1.5m
Component Check
Electrical
More than 20m
■ By UPS
1m
u lt
Fa
Solution Check
[ACP] [UPS]
5m
Test functions
[ACP] [UPS]
-239-
I. Phenomenon:
Basic Part
Indoor unit operation mode is sometimes auto-
changed (Cooling/ Heating Fan, AI…)
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Operation
auto-change
Solution Check
Not reset system after Y
changing S.C.C DIP Reset system power
switch
N
S.C.C adapter failure Y

Change new one
or incorrect
Test functions
N
PI485’s CN_Dry Y
connector was Insert
inserted?
N
485 nodes is arranged Y
in Star topology Re-wiring
(serial)?
-240-
Not reset S.C.C power after setting DIP switch (to Slave) can cause
Basic Part
malfunction
Always reset power of controller (ACP and S.C.C) after changing

system configuration.
Cooling FAN
Troubleshooting
Guide for each
Error Code
20 21 22 23
Reset power. 10 11 12 2D
Cooling AI
Component Check
Reset
[ACP rebooting] Electrical

Solution Check
[S.C.C rebooting]
Test functions
-241-
One S.C.C unit need 9V, 300mA as standard power supply.
Basic Part
Lower or incorrect spec cause S.C.C malfunction.
We recommend using adapter (as table below) instead of DC

power from PI485.
Troubleshooting
Guide for each
Error Code
Cooling FAN
20 21 22 23
Adapter spec. checking 10 11 12 2D
Component Check
Cooling AI
Electrical
u lt
Fa
Solution Check
10V, 500mA adapter
S.C.C 1~4EA S.C.C 5~8EA

end
1.2A (9V) 2.5A (9V)
mm
6708AQ0001B - c o
R e
Test functions
-242-
Basic Part
CN_Dry connector must be plugged into PI485 in order to keep
Lock function working. (*)
Cooling FAN
Troubleshooting
Guide for each
20 21 22 23
Error Code
10 11 12 2D
Cooling AI
Is CN_Dry connector plugged-in?
Component Check
CN_Dry
Electrical
connector
plug-in
Solution Check
Note:
Incase of new model PI485 (8pin DIP switch), turn the 5th switch ON
Test functions

-243-
Basic Part
We recommend you arrange the wire as a connected serial of
point-to-point 485 nodes (PI485 Gateway) before connecting to
Controller’s 485 port.
Star topology
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Bus topology
Join
Solution Check
Test functions
end
mm
c o
Re
-244-
I. Phenomenon:
Basic Part
Some indoor accumulated pwr. is displayed = 0
(indoor unit under working normally)
Troubleshooting
Guide for each
Error Code
Component Check
AC (13) acc pwr 0 kwh
II. Reason and Solving: Electrical

Solution Check
Eliminate reason caused by 242 error on I/ U
(refer to the previous part for solving first)
I/U acc. Pwr.

=0
Test functions
Y
I/ U address wrong
Re-setting
setting?
-245-
Basic Part
Setting range of indoor unit address on PDI is wrong.
PDI re-setting (refer manual)
Troubleshooting
Guide for each
Error Code
20 21 22 23
10 11 12 13
Pwr. = 0 kwh
(Start) (End)
lt
Component Check
(10) (12)
u
Fa
Electrical
(Start) (End)
(10) (13)
Solution Check
Test functions
-246-
Case D2: all indoor acc. Pwr. in one group are
displayed = 0
I. Phenomenon:
Basic Part
All indoor accumulated pwr. in same group are
displayed = 0
(indoor unit under working normally)
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
[ER-02 no pulse]
Test functions
[Display only total acc. pwr]
-247-
displayed = 0
Basic Part
Eliminate reason caused by 242 error on I/ U
(refer to the previous part for solving first)
All I/U acc.
Troubleshooting
Pwr. = 0
Guide for each

Error Code
Y
Connection with watt
Re-wiring
meter wrong?
485 connection to Y
Re-wiring
ACP wrong?
Component Check
Electrical
Solution Check
Test functions
-248-
displayed = 0
Basic Part
Wrong connection with Watt meter cause malfunction.
20 21 22 23
Troubleshooting
Guide for each
Error Code
10 11 12 13
0 kwh 0 kwh 0 kwh 0 kwh
Watt meter
Component Check
Electrical
CN_WATTMETER Check the connection (+, - )
white white
black black
[watt meter] [PDI]
u lt
Fa Solution Check
white white
black black
[watt meter] [PDI]
Test functions
-249-
displayed = 0
Basic Part
Wrong connection with ACP cause malfunction.
20 21 22 23
Troubleshooting
Guide for each
Error Code
Check the connection 10 11 12 13
Bus_A, Bus_B
0 kwh 0 kwh 0 kwh 0 kwh
Component Check
CN_OUTFAN
Electrical
Bus_A A
Bus_B B
u lt
Fa
Bus_A A Solution Check
Bus_B B
Test functions
-250-
Case D3: Value on ACP and PDI doesn’t match
I. Phenomenon:
Basic Part
Data on ACP and PDI is not same

ACP with version lower than 3.30.3e has poor
function of data update from PDI
up-grade ACP to 3.30.3e version
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-251-
I. Phenomenon:
Basic Part
Total accumulated pwr. on ACP doesn’t
match to Watt meter.
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Solution Check
Test functions
-252-
Basic Part
Setting of Watt meter in PDI is wrong.
Troubleshooting
ult
Guide for each

Error Code
F a
1 w/ pulse
2 W/ P
Component Check
Electrical
2 w/ pulse
Solution Check
Test functions
-253-
I. Phenomenon:
Basic Part
ACP can’t control ventilator.
Display error
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
Vent. error
address wrong setting Y Solution Check

check and setting
(duplicate, not in-
address again
range)
N
PI485 DIP switch Y

Re-setting
wrong setting?
N
Test functions
Main PCB DIP switch Y

Re-setting
wrong setting?
485 wrong Y
Re-wiring
connection?
-254-
PI485 DIP switch wrong setting
Basic Part
485 cable wrong connection.
TX ↔ Bus_A LED02G, 03G

RX ↔ Bus_B
Troubleshooting
alternately blink
Guide for each

Error Code
Component Check
DIP switch
3,4 ON
Electrical
[Correct]
Solution Check
Test functions
-255-
Main PCB DIP switch wrong setting
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
1,4 ON
[Correct]
Be sure to reset PCB after setting
Solution Check
Test functions
-256-
Appendix:
I. Using external PI485 (PMNFP14A0/ PMNFP14A1) for Multi V System
Basic Part
Troubleshooting
Guide for each
Error Code
0: apply PMNFP14A0,
Component Check
X: not apply PMNFP14A1
PI485 setting method
Electrical
For Multi V system
[1,4,5 ON]
Example:
Only the combination Plus II Outdoor unit, Plus II indoor units and
Wide wired remote controller doesn’t require external PI485 in order to
use Lock function (All/ Mode/ Fan/ Temp. lock)
Solution Check
II. Jumper (CN_Dry) or 5th switch of 8pin DIP switch PI485 setting in order
to use Lock function Test functions
-257-
C. Technical bulletin
-258-
Technical bulletin
-259-
-260-
Technical bulletin
-261-
Technical bulletin
-262-
-263-
-264-
-265-
-266-
Technical bulletin
-267-
-268-
Technical bulletin
-269-
-270-
Technical bulletin
-271-
-272-
Technical bulletin
-273-
-274-
Technical bulletin
-275-
Technical bulletin
-276-
(Plus II, Sync II)
Test functions
-277-
5
.
-278-
-279-
(Sync II)
(Sync II)
-280-
-281-
5.1 Sensor checking
5. Test functions
-282-
-283-
5.2 Auto charging
-284-
-285-
5.3 Auto refrigerant checking
-286-
-287-
5.4 Pump down
-288-
5.5 Pump out
-289-
5.6 Vacuum mode
Basic Part
Troubleshooting
Guide for each
Error Code
Component Check
Electrical
5.7 Static pressure compensation mode
Solution Check
This function secures the air flow rate of ODU, in case static pressure has been
applied like using duct at fan discharge of ODU.
Test functions
-290-
5.8 Pipe Searching (Sync, Sync II)
Automatic Pipe Searching
Confirm the IDU auto addressing setting
Basic Part
Turn off “No.1 of SW02M of the HRU”
Check the proper setting of

No. 2 & 3 of SW02M of the HRU
(Model of HRU & number of IDU)
Troubleshooting
Guide for each
Error Code
Confirm the No. 5 DIP S/W of SW01B
of the ODU PCB
- Outdoor temp is over 15℃ : ON
- Outdoor temp is below 15 ℃ : OFF
In case of changing 5 DIP S/W of SW01B
Component Check
of the ODU, reset power of the ODU main
PCB.
Electrical
Wait for 3 minute
Press SW01V of the ODU main PCB

for 5 second

at 7-seg of the ODU main PCB, and
Solution Check
then ’88’ is displayed
Outdoor unit is operating

for 5~30 minutes.
After ODU stopped, the number of IDU Display error on the ODU PCB / HRU PCB
detected is displayed at 7-seg of the ODU - ODU PCB : HR unit No.  Valve No.
main PCB for 1 minute (Example: H1 01)
- HRU PCB : ‘200’
Test functions
Equal number of IDU No

and displayed one?
in terms of “piping” Check the piping among ODU, IDU, HRU
Yes
Completion of the auto pipe detection Retry auto pipe detection
-291-
-292-
Manual Pipe Searching
In case of auto pipe detection failure
Basic Part
Turn on “No.1 of SW02M of HR unit”
Troubleshooting
Guide for each
Error Code
Enter central control address into each IDU
using its wired remote controller
Manually set the address of each valve

corresponding with the central control
address of IDU connected to the valve
Component Check
Turn on No.5 of SW01B
Electrical
of ODU PCB”
Reset the power of ODU PCB
Wait for about 5 minutes
Solution Check
The number of IDU installed is displayed
No
Equal number of
“IDU and Displayed one”?
Test functions
Yes
Turn off No.5 of SW01B Check the central control address of IDU
of ODU PCB and HRU
Completion of the manual pipe detection Retry manual pipe detection
-293-
-294-
-295-
5.9 Manual setting example
Appendix #1 : Resistance Value of temperature sensor
Pipe Temperature Sensor
Basic Part
Indoor unit
- Pipe Inlet Pipe Temp.
- Pipe Outlet Pipe Temp.
Outdoor unit
- Suction Temp.
- Subcooling Circuit Inlet Temp.
- Subcooling Circuit Outlet Temp.
- Liquid Pipe Temp.
- Hex Temp.
Troubleshooting
Guide for each
Error Code
Air Temperature Sensor
- Indoor unit Air temp.

- Outdoor unit Air temp.
Comp. Discharge Temperature

Sensor
- Inverter Comp. discharge temp.

- Constant Comp. discharge temp.
Component Check
Electrical
* Refer: Resistance value maybe
change according to temperature
of temp sensor, It shows according
to criteria of current temperature
(±5% margin)
Solution Check
Test functions
-296-
Basic Part
Indoor unit
Outdoor unit
- Suction Temp.
- Liquid Pipe Temp.
- Hex Temp.
Troubleshooting
Guide for each
Error Code


Sensor

Component Check
Electrical
(±5% margin)
Solution Check
Test functions
-297-
Basic Part
Indoor unit
Outdoor unit
- Suction Temp.
- Liquid Pipe Temp.
- Hex Temp.
Troubleshooting
Guide for each
Error Code


Sensor

Component Check
Electrical
(±5% margin)
Solution Check
Test functions
-298-

Multi V Trouble Shooting Guide Book - 0912

Uploaded by

Copyright:

Available Formats

Multi V Trouble Shooting Guide Book - 0912

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Multi V Trouble Shooting Guide Book - 0912

Uploaded by

Copyright:

Available Formats

What are the main sections covered in the document?

What are the main sections covered in the document?

What troubleshooting steps are described?

What troubleshooting steps are described?

2009.

Search with Error Code number .................................…............... 4

1. Basic Part ..............................................................……............... 5

2. Troubleshooting Guide for each Error Code (Refer page 4) …. 43

3. Electric Component Check ........................................................ 172

4. Solution Check ........................................................................... 199

5. Test functions (Plus II) ………………………………………………………….. 277

Appendix #1 : Resistance value table of temperature sensor ………296

B: Inverter and Heat Recovery

Guide for each

9 Indoor LEV Pulse 800~1900 - 200~1350 - Pipe Inlet/outlet Subcooling control

300~1600 below 200 below 200 Overcharging

- The pressure is relative value.

Guide for each

30 1781.19 1775.59 1800 30.36 30.47

1.7.1.1 Multi V Plus Main Unit

01 Indoor unit air sensor error

Guide for each

Change the PCB

Refer: Resistance value maybe change according to temperature of temp sensor,

CN-ROOM : Indoor air temp sensor

CN-PIPE2 : Pipe outlet temp sensor

CN-PIPE1 : Pipe inlet temp sensor

Measure the resistance of outlet pipe temp sensor.

1. Remote controller fault

Does the error happens No

Replace indoor unit PCB ***

※The PCB can differ from model to model.

Checking transmission cable connection status

1. Drain pump/float switch fault

Is the drain pan filled

In indoor unit PCB

Replace Drain Pump

*If the float goes up higher than a half of float switch

(High position  Open )

Float switch connector

1. Auto addressing is not done

Error diagnosis and countermeasure flow chart

Replace the PCB of indoor unit

Guide for each

Yes Replace main PCB fuse after

Check the insulation of inverter

Yes Replace after capacity of

Indoor PCB fault

Indoor unit outlet pipe Indoor unit outlet pipe temperature

Error diagnosis and countermeasure flow chart

*** Dissolution method CH07 with remote controller

Problem in EEPROM inside 1.Error developed in transmission between the micro-

1. Motor connector connection fault

Replace indoor unit PCB **

<Checking connection state of fan motor connector>

Indoor unit doesn’t get signal

After ODU main PCB No No

Multi B Plus II / Sync II / Multi V MINI Multi V MINI

U-V : 1.16Ω ± 7% U-V : 1.083Ω± 10%