Scribd Logo
Upload

Welcome to Scribd!

  • 615 views

    Keli XK3118 T1 Manual Tecnico

    Uploaded by

    fabian almeida
    This technical manual provides specifications and operating instructions for the Keli Electirc XK3118T1 indicator. The main parameters include an AD switch mode of 10 times per second, supporting 1-6 load cells rated at 350Ω, and an input range of -16mV to 18mV. Calibration instructions are provided in multiple steps for settings such as divisions, tare, full capacity, and zero calibration. Additional calibration parameters that can be set include zero tracking, manual zero, auto zero, and digital filter settings. Connection of load cells and indicators requires proper shielding and grounding.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Keli XK3118 T1 Manual Tecnico

    Uploaded by

    fabian almeida
    615 views3 pages
    This technical manual provides specifications and operating instructions for the Keli Electirc XK3118T1 indicator. The main parameters include an AD switch mode of 10 times per second, supporting 1-6 load cells rated at 350Ω, and an input range of -16mV to 18mV. Calibration instructions are provided in multiple steps for settings such as divisions, tare, full capacity, and zero calibration. Additional calibration parameters that can be set include zero tracking, manual zero, auto zero, and digital filter settings. Connection of load cells and indicators requires proper shielding and grounding.

    Original Title

    Keli XK3118 T1 Manual tecnico

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This technical manual provides specifications and operating instructions for the Keli Electirc XK3118T1 indicator. The main parameters include an AD switch mode of 10 times per second, supporting 1-6 load cells rated at 350Ω, and an input range of -16mV to 18mV. Calibration instructions are provided in multiple steps for settings such as divisions, tare, full capacity, and zero calibration. Additional calibration parameters that can be set include zero tracking, manual zero, auto zero, and digital filter settings. Connection of load cells and indicators requires proper shielding and grounding.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    615 views3 pages

    Keli XK3118 T1 Manual Tecnico

    Uploaded by

    fabian almeida
    This technical manual provides specifications and operating instructions for the Keli Electirc XK3118T1 indicator. The main parameters include an AD switch mode of 10 times per second, supporting 1-6 load cells rated at 350Ω, and an input range of -16mV to 18mV. Calibration instructions are provided in multiple steps for settings such as divisions, tare, full capacity, and zero calibration. Additional calibration parameters that can be set include zero tracking, manual zero, auto zero, and digital filter settings. Connection of load cells and indicators requires proper shielding and grounding.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Keli Electirc

    XK3118T1 Technical Manual

    ：
    1. Main Technical Parameter：

    ：
    AD Switch Mode： ∑—∆，10times per second

    Load Cell Excitation: DC +5V，can connect with 1-6pcs 350Ω strain gauge load cell.

    Signal Input Range: -16mV～18mV；

    Input Sensitivity: ≥1.5uV/e

    ：Adopts 6 wire type（Long wire auto compensation）


    Load Cell Connection：

    ： AC 110～240V，50～60Hz；inbuilt 6V/4AH maintenance-free


    Indicator Power Supply：

    lead-acid battery

    ： 0～40 。
    Working Temperature：

    II. ：
    Connection with Load Cell：

    Assignment

    ① -Excitation

    ② -Feed Back

    ⑥ +Excitation

    ⑦ +Feed Back

    ⑧ -Signal

    ⑨ +Signal

    ⑤ Shield Wire

    Short connect PIN 1 and 2, PIN 6 and 7 when connected a load cell with 4 wire cable;

    ！Connection between load cell and indicator must be reliable, shield wire must be
    ▲！

    connected to ground reliably. Connection or disconnection are not allowed when the
    indicator is on, which may damage the indicator or load cells.

    1
    Keli Electirc
    ▲ ！ Static protection must be properly adopted as the load cell and indicator are all

    static sensitive equipments. Welding or other strong electricity operation should be


    strictly forbidden. During thunderstorm season, proper lightening protection should be
    tanken care of to protect the load cells and indicators from damaging by lightening and
    to ensure the personal safety and the safely running of the weighing and related
    equipments.

    III. Calibration

    Turn on the indicator, after self check it will enter normal weiging display. Warm up for 15~30
    minutes and open the calibration cover in the back side of the indicator. The calibration status

    Steps Operation Display Note


    【 CAL 】 Means calibration status has enterred. Press ”↙” for next step
    1 “↑”to select division 【E 01】 Divisions Setting：1、2、5、10、20、50
    “↑”to select tadix point ：Indicator directly shows the Radix Point
    Radix Point Setting：
    2 “↙” to confirm 【dC 0】

    Full Capacity Setting Full Capacity Setting:


    Press ”→” the flash digit will move towards right
    3 【F030.00】
    Press ”↑” to increase the number of flash digit
    Press “ ” to confirm and enter next step such as 3000
    Press for confirm after Zero Calibration：Make indicator under noload status, press “ ” after
    4 date stable 【noLoAd】
    date stable to confirm Zero
    Input Loading Weight
    【AdLoAd 】 Linearity Calibration：Load weight, the closer to the full capacity the
    After display for better. Operation is same as full capacity setting.
    2 seconds, auto
    5 Press “↙” to confirm and automatically exit calibration status 5 seconds
    switch to load
    input after the stable indicator light on
    【003.000】 Such as：3000

    Back to Working Status 【 3.000】 After calibration, the current weight will be displayed
    will be enterred after pressing the calibration butto. Following are the details:

    IV. Setting for Other Calibraion Parameter

    After enter the calibration status and display 【CAL】, press “↑”and the indicator will display

    【Zero】 and then press “↙” to enter setting for other calibration parameter. Following are the

    details:
    Steps Operation Display Note
    Means other calibration parameter setting has enterred.
    【Zero】
    Press ”↙” for next step
    “↑”to switch
    1 【Zot *.*】 Zero Trace：0～4d
    “↙”to confirm
    “↑”to switch
    2 【nt **】 ：
    Manual Set Zero：
    “↙”to confirm

    2
    Keli Electirc
    0，2，4，10，20，100 % of full capacity

    ：
    Auto Set Zero：

    0，2，4，10，20，100 % of full capacity


    “↑”to switch
    3 【At **】
    “↙”to confirm Select【--】for turn off zero saving function, i.e. the last

    turn off zero that manually set will be the turn on zero
    when the indiator turn on next time and the auto zero
    will not be carried out again.

    Filter：

    “↑”to switch
    4 【FL ***】 【S t b】：Stable
    “↙”to confirm

    【SEn】
    ：Sensitive

    You might also like