HCD V41D

2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SERVICE MANUAL AEP Model
UK Model
Ver. 1.2 2019.03
E Model
Australian Model
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Model Name Using Similar Mechanism MHC-V44D/V50D

DVD Mechanism Type CDM90-DVBU204
CMS-S76RFS7G1 or
Optical Pick-up Block Name
CMS-S76RFS7GP
SPECIFICATIONS
Speaker section HDMI section BLUETOOTH section NFC section General
Speaker system: Connector: Communication system: Operating frequency: Power requirements:
3-way Type A (19 pin) BLUETOOTH Standard version 4.2 13.56 MHz AC 120 V – 240 V, 50/60 Hz
Speaker unit: Output: Power consumption:
Tweeter L/R: 40 mm, cone type Disc player section BLUETOOTH Standard Power Supported audio formats 130 W
Midrange L/R: 80 mm, cone type System: Class 2 Supported bit rate and sampling Power consumption (at the Power
Woofer: 250 mm, cone type Compact disc and digital audio Maximum communication range: frequencies: Saving mode):
Rated impedance: and video system Line of sight approx. 10 m* MP3: 0.5 W (When “BT STBY” is set to
Tweeter L/R: 4 ohms Laser Diode Properties Frequency band: 32/44.1/48 kHz, “OFF” and [CONTROL FOR HDMI] is
Midrange L/R: 4 ohms Emission Duration: Continuous 2.4 GHz band 32 kbps – 320 kbps (VBR) set to [OFF].)
Woofer: 6 ohms Laser Output*: Less than 44.6 μW (2.4000 GHz - 2.4835 GHz) AAC: 2 W* (When “BT STBY” is set to
* This output is the value Maximum output power: 44.1 kHz, 48 kbps – 320 kbps “ON” and [CONTROL FOR HDMI] is
Inputs measurement at a distance of < 9.5 dBm (CBR/VBR) set to [ON].)
AUDIO/PARTY CHAIN IN (TV) L/R: 200 mm from the objective lens WMA:
Modulation method: Dimensions (W/H/D) (Approx.):
Voltage 2 V, impedance surface on the Optical Pick-up 44.1 kHz, 48 kbps – 192 kbps (CBR/
FHSS (Freq Hopping Spread 328 mm × 796 mm × 308 mm
47 kilohms Block with 7 mm aperture.
Spectrum) VBR) Mass (Approx.):
TV (ARC): Frequency response:
Compatible BLUETOOTH profiles**: WAV: 13.5 kg
20 Hz – 20 kHz
Supported audio signal: A2DP (Advanced Audio 44.1/48 kHz (16 bit)
2-channel Linear PCM Video color system format: * The power consumption of the system
Distribution Profile)
MIC1: Latin American model: Supported video formats will be less than 0.5 W when there is no
AVRCP (Audio Video Remote HDMI connection and “BT STBY” is set
Sensitivity 1 mV, impedance NTSC Xvid:
Control Profile) to “OFF.”
10 kilohms Other models: Video codec: Xvid video
SPP (Serial Port Profile)
MIC2/GUITAR: NTSC and PAL Bit rate: 4.854 Mbps (MAX)
Supported codecs:
Sensitivity 1 mV, impedance
USB section SBC (Subband Codec) Resolution/Frame rate: Unpacking
10 kilohms (When the Guitar AAC (Advanced Audio Coding) 720 × 480, 30 fps
Supported USB device: t This unit (MHC-V41D) (1)
mode is turned off.) LDAC 720 × 576, 25 fps (except for Latin
Mass Storage Class t Remote control (1)
Sensitivity 200 mV, impedance HFP (Hands-free Profile) American model)
Maximum current: t R03 (size AAA) batteries (2)
1 Megaohm (When the Guitar HSP (Headset Profile) Audio codec: MP3
1A t FM lead antenna (1)
mode is turned on.) MPEG4:
(USB) port: * The actual range will vary depending t AC power cord (mains lead) (1)
File format: MP4 File Format
Outputs Type A on factors such as obstacles between t AC plug adaptor* (1) (supplied only
Video codec: MPEG4 Simple
devices, magnetic fields around a for certain areas)
AUDIO/PARTY CHAIN OUT L/R: Profile (AVC is not compatible.)
FM tuner section microwave oven, static electricity,
Voltage 2 V, impedance 1 kilohm FM stereo, FM superheterodyne tuner reception sensitivity, antenna’s Bit rate: 4 Mbps * This plug adaptor is not for the use in
VIDEO OUT: performance, operating system, Resolution/Frame rate: Chile, Paraguay and Uruguay. Use this
Antenna:
Max. output level 1 Vp-p, software application, etc. 720 × 480, 30 fps plug adaptor in the countries where it
FM lead antenna is necessary.
unbalanced, Sync. negative load ** BLUETOOTH standard profiles 720 × 576, 25 fps (except for Latin
Tuning range:
impedance 75 ohms indicate the purpose of BLUETOOTH American model)
87.5 MHz – 108.0 MHz (50 kHz communication between devices. Design and specifications are subject
HDMI OUT: Audio codec: AAC-LC (HE-AAC is
step) (Except Brazilian model) to change without notice.
Supported audio signal: not compatible.)
76.0 MHz – 108.0 MHz (100 kHz
2-channel Linear PCM (up to DRM: Not compatible
step) (Brazilian model)
48 kHz), Dolby Digital
HOME AUDIO SYSTEM

9-896-491-03
2019C33-1
© 2019.03 Sony Video & Sound Products Inc.
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
License and Trademark Notice t Android and Google Play are

trademarks of Google LLC. Self-diagnosis function
t is a trademark of DVD Format/
Logo Licensing Corporation. t Apple, the Apple logo, iPhone, and
iPod touch are trademarks of Apple When letters/numbers appear
t “DVD+RW,” “DVD-RW,” “DVD+R,”
Inc., registered in the U.S. and other on the TV screen or the display
“DVD-R,” “DVD VIDEO,” and the “CD”
countries. App Store is a service When the self-diagnosis function
logos are trademarks.
mark of Apple Inc.
t WALKMAN® and WALKMAN® logo is activated to prevent the system
t Siri is a trademark of Apple Inc.
are registered trademarks of Sony from malfunctioning, a service
Corporation. t “Made for iPod,” and “Made for number appears. The service
iPhone” mean that an electronic
t MPEG Layer-3 audio coding number consists of an alphabet
accessory has been designed
technology and patents licensed and numerals (e.g. C 13 50). See the
to connect specifically to iPod
from Fraunhofer IIS and Thomson. following table for the cause and
or iPhone, respectively, and has
t Windows Media is either a been certified by the developer corrective action.
registered trademark or trademark to meet Apple performance
of Microsoft Corporation in First 3 Cause and corrective
standards. Apple is not responsible
the United States and/or other characters of action
for the operation of this device the service
countries. or its compliance with safety and number
t This product is protected by regulatory standards. Please note
certain intellectual property rights that the use of this accessory with
C 13 This disc is dirty.
of Microsoft Corporation. Use or iPod or iPhone may affect wireless t Clean the disc with a
distribution of such technology performance. soft cloth.
outside of this product is prohibited t THIS PRODUCT IS LICENSED UNDER C 31 The disc is not inserted
without a license from Microsoft or THE MPEG-4 VISUAL PATENT correctly.
an authorized Microsoft subsidiary. PORTFOLIO LICENSE FOR THE t Turn off the system,
t This system incorporates Dolby* PERSONAL AND NON-COMMERCIAL then turn it back on
Digital. USE OF A CONSUMER FOR again. Then re-insert the
* Manufactured under license from disc correctly.
Dolby Laboratories. Dolby, Dolby (i) ENCODING VIDEO IN
Audio, and the double-D symbol are COMPLIANCE WITH THE MPEG-4 E XX To prevent a
trademarks of Dolby Laboratories. VISUAL STANDARD (“MPEG-4 (XX is a malfunction, the system
t This system incorporates High- VIDEO”) number) has performed the
Definition Multimedia Interface self-diagnosis function.
AND/OR
(HDMI™) technology. The terms t Contact your nearest
HDMI and HDMI High-Definition (ii) DECODING MPEG-4 VIDEO THAT Sony dealer or local
Multimedia Interface, and the HDMI WAS ENCODED BY A CONSUMER authorized Sony service
Logo are trademarks or registered ENGAGED IN A PERSONAL AND facility and give the
trademarks of HDMI Licensing NON-COMMERCIAL ACTIVITY 5-character service
Administrator, Inc. in the United AND/OR WAS OBTAINED FROM number.
States and other countries. A VIDEO PROVIDER LICENSED TO Example: E 61 10
t “BRAVIA” is a trademark of Sony PROVIDE MPEG-4 VIDEO.
Corporation. NO LICENSE IS GRANTED OR SHALL
t LDAC™ and LDAC logo are BE IMPLIED FOR ANY OTHER
trademarks of Sony Corporation. USE. ADDITIONAL INFORMATION
t The BLUETOOTH® word mark and INCLUDING THAT RELATING TO
logos are registered trademarks PROMOTIONAL, INTERNAL AND
owned by Bluetooth SIG, Inc. and COMMERCIAL USES AND LICENSING
any use of such marks by Sony MAY BE OBTAINED FROM MPEG LA,
Corporation is under license. Other L.L.C.
trademarks and trade names are HTTP://WWW.MPEGLA.COM
those of their respective owners. t All other trademarks are trademarks
t The N-Mark is a trademark or of their respective owners.
registered trademark of NFC Forum, t In this manual, ™ and ® marks are
Inc. in the United States and in other not specified.
countries.
CAUTION
The use of optical instruments with
this product will increase eye hazard.
For customers in Europe
NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
For customers in the United • Notice that the minus side of a tantalum capacitor may be dam-
Arab Emirates aged by heat.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
CAUTION THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
Use of controls or adjustments or performance of procedures REPLACE THESE COMPONENTS WITH SONY PARTS
other than those specified herein may result in hazardous radia- WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
tion exposure. MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 4 6. DIAGRAMS

6-1. Block Diagram - SERVO/USB/VIDEO Section - .......... 43
2. DISASSEMBLY 6-2. Block Diagram - AUDIO Section -................................. 44
2-1. Disassembly Flow ........................................................... 9 6-3. Block Diagram - AMP/PANEL Section - ....................... 45
2-2. Side Panel ....................................................................... 10 6-4. Block Diagram - POWER SUPPLY Section - ................ 46
2-3. Top Panel Block-1........................................................... 11 6-5. Printed Wiring Board
2-4. Top Panel Block-2........................................................... 12 - MOTHER Board (Side A) (Former MB type) - ........... 48
2-5. Loading Panel Block ....................................................... 13 6-6. Printed Wiring Board
2-6. Loading Panel ................................................................. 14 - MOTHER Board (Side B) (Former MB type) - ........... 49
2-7. CDM Block ..................................................................... 15 6-7. Printed Wiring Board
2-8. FFC Holder ..................................................................... 16 - MOTHER Board (Side A) (New MB type) - ............... 50
2-9. Optical Pick-up Block (CMS-S76RFS7G) ..................... 17 6-8. Printed Wiring Board
2-10. Rear Panel Block ............................................................ 18 - MOTHER Board (Side B) (New MB type) - ............... 51
2-11. PARTY LED Board......................................................... 18 6-9. Schematic Diagram - MIC Board - ................................. 52
2-12. DC Fan, Rear Panel ........................................................ 19 6-10. Printed Wiring Board - MIC Board - .............................. 53
2-13. Chassis Block .................................................................. 20 6-11. Printed Wiring Board - IR Board -.................................. 53
2-14. SMPS Board ................................................................... 21 6-12. Schematic Diagram - IR Board - .................................... 53
2-15. MOTHER Board ............................................................. 22 6-13. Printed Wiring Board - GESTURE Board -.................... 54
2-16. MIC Board ...................................................................... 23 6-14. Schematic Diagram - GESTURE Board - ...................... 55
2-17. PANEL Board ................................................................. 24 6-15. Printed Wiring Board - PANEL Board - ......................... 56
2-18. Electret Cap Microphone ................................................ 25 6-16. Schematic Diagram - PANEL Board - ............................ 57
2-19. NFC Board ...................................................................... 25 6-17. Printed Wiring Board - SMPS Board - ........................... 58
2-20. GESTURE Board ............................................................ 26 6-18. Schematic Diagram - SMPS Board - .............................. 59
2-21. Front Panel Block-1 ........................................................ 27
2-22. Front Panel Block-2 ........................................................ 28 7. EXPLODED VIEWS
2-23. SW LED Board, IR Board .............................................. 29 7-1. Side Panel Section .......................................................... 61
2-24. Loudspeaker (Tweeter) ................................................... 30 7-2. Top Panel Section ........................................................... 62
2-25. Loudspeaker (Midrange)................................................. 31 7-3. Loading Panel Section .................................................... 63
2-26. Loudspeaker (Subwoofer)............................................... 32 7-4. Rear Panel Section .......................................................... 64
2-27. Chassis Block Service Position....................................... 33 7-5. Chassis Section ............................................................... 65
2-28. Top Panel Block Service Position ................................... 33 7-6. Front Panel Section ......................................................... 66
7-7. Speaker Cabinet Section ................................................. 67
3. TEST MODE ............................................................ 34 7-8. CDM Block Section ........................................................ 68
7-9. DVD Mechanism Deck Section
4. ELECTRICAL CHECKS ...................................... 37 (CDM90-DVBU204) ...................................................... 69
5. TROUBLESHOOTING .......................................... 38 8. ELECTRICAL PARTS LIST .............................. 70
Accessories are given in the last of the electrical parts list.
Note: The MOTHER board has been changed in the midway of

production.
Refer to “CHANGE OF MOTHER BOARD” on page 8
for “Former MB type” and “New MB type”.
3
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2 SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
IMPORTANT NOTE OF PERFORMING THE OPERA-

NOTES ON HANDLING THE OPTICAL PICK-UP
TION CHECK
BLOCK OR BASE UNIT
When performing the operation check of this unit, be sure to per-
The laser diode in the optical pick-up block may suffer electro- form the operation check after checking that it is in the following
static break-down because of the potential difference generated by state.
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also • Heat sink is installed to MOTHER board
use the procedure in the printed matter which is included in the • Fan motor is connected to MOTHER board
repair parts. Note: If turn the power on in the state that heat sink is not installed, there is
a possibility of damage.
The flexible board is easily damaged and should be handled with Also, be sure to perform the operation check in the connect the fan
care. motor to the MOTHER board, and the fan motor is rotating state.
If it is necessary to perform the operation check with the heat sink
NOTES ON LASER DIODE EMISSION CHECK removed or the fan motor removed, set the volume to 10 or less and
The laser beam on this model is concentrated so as to be focused perform the operation check within 1 minute.
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission, fan motor
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with heat sink
the lead free mark due to their particular size)
: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher MOTHER board
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
If “PROTECTX” (X is a number) APPEARS ON THE
applied to the solder joint for a slightly longer time.
DISPLAY, THEN “CHECK MANUAL” FLASHES ON
Soldering irons using a temperature regulator should be set to
THE DISPLAY.
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if Immediately unplug the AC
power cord (mains lead), and
the heated tip is applied for too long, so be careful! check if anything is blocking the
• Strong viscosity ventilation openings of the unit.
Unleaded solder is more viscous (sticky, less prone to flow)
After you have checked and
than ordinary solder so use caution not to let solder bridges found no problems, reconnect
occur such as on IC pins, etc. the AC power cord (mains lead),
• Usable with ordinary solder and turn on the system.
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. Protect Type Description:
Protect
Contents
No.
Defect of thermistor IC or charging circuit used by
2
SPM (Sound Pressure Management) system.
Power supply over current.
or
DC appears in SP terminal by defect of AMP IC.
3
or
Unusual heat up of AMP IC by improper assembly of
heat sink.
6 Defect of DC FAN and DC FAN driver circuit.
4
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
CAPACITOR ELECTRICAL DISCHARGE PROCESSING MODEL IDENTIFICATION

When removing the MOTHER board and SMPS board after check- Distinguish by destination code on the rear side of the main unit.
ing the operation of this unit, be sure to perform the discharge pro-
cessing of C2076 on the MOTHER board and C6302 on the SMPS AEP, UK
board before removing the boards.
When it is removed the boards without performing the discharge
processing and it is shorted the both end of C2076 on the MOTH- Serial label
ER board, it might be damaged the DAMP IC.
Destination code
Perform the discharge processing with referring the figure below.
Note: Be sure to discharge using a resistor of 800  or higher.
E93, BR, AR, TH, IND
– Top view –
MOTHER board SMPS board
Perform the discharge

processing with
connecting the resistor Destination code
to the hole of C6301 RU, AUS, E4, SP, LA
that is not mounted
the part. Serial label
– Rear view –
Destination code
C2076 C6302
Perform the discharge processing 800 :/2 W

with connecting the resistor between
PVDD (any one 6 to 9 pin) and PGND Destination code Destination
(any one 1 to 5 pin) of CN2007. AR2 AR model
AU1 AUS model
800 :/2 W BR1 BR model
CEK UK model
CEL AEP model
E4 E4 model
E12 IND model
E93 E93 model
LA9 LA model
RU1 RU model
SP6 SP model
TH1 TH model
Note: For detail about the destination, refer to “DESTINATION ABBRE-
VIATIONS” below.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AEP : European area (Except for Ireland, UK), East European
area, CIS area (Moldova) and Middle East area (Jordan)
models
AR : Argentina model
AUS : Australian and New Zealand models
BR : Brazilian model
E4 : Middle East area (Except for Iraq, Jordan, Kuwait, Saudi
Arabia, UAE) and African area (Except for Kenya, Nige-
ria, Tanzania) models
E93 : Middle East area (Iraq, Kuwait, Saudi Arabia, UAE) and
African area (Kenya, Nigeria, Tanzania) models
IND : Indian model
LA : Latin American area (Except for Argentina, Brazil) model
RU : CIS area (Except for Moldova) model
SP : South East Asian area (Except for India, Thailand) model
TH : Thai model
UK : UK and Ireland models
5
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
IMPORTANT 4. Press the [ +]/[– ] buttons to select target destination, and

press the [ ] button on the remote commander.
DESTINATION SETTING METHOD 5. The message “RESET” is displayed on the vacuum fluorescent
The destination information isn’t written in the MOTHER board for display, then start the initialization (power off (demonstration
the service. mode) → power on → power off (demonstration mode)) auto-
Therefore, when the MOTHER board is replaced, be sure to per- matically.
Note 5: Don’t disconnect the power supply cord during the initializa-
form the destination setting (Important work).
tion.
Note 1: The initial setting destination of the MOTHER board for the
service is “LA”. The message “D LATIN” is displayed on the Screen display
vacuum fluorescent display.
Note 2: When distinguishing the destination of the product, refer to the
“MODEL IDENTIFICATION” on page 5. 6. When the initialization is completed, the destination change is
Note 3: If destination setting isn’t performed, it is possibility to occur the completed.
defect to each operation of this unit. 7. When checking the setting destination, refer to the “PANEL TEST
MODE” on page 35.
Procedure:
1. Press two buttons of the [SOUND FIELD] and [TUNING +
>] simultaneously for 3 seconds during the demonstration NFC OPERATION CHECKING METHOD
mode. When the MOTHER board is replaced, it is necessary to check that
2. It enters the destination setting mode, the message “D LATIN” pairing is normally performed.
is displayed on the vacuum fluorescent display. Perform the operation check according to the following procedure.
Note 4: If the message “DEST LOCK” is displayed on the vacuum
fluorescent display, press the [ ] button on the remote com-
Note: Be sure to delete paring information after checking the pairing.
mander to release from this mode. Because the destination is
locked, and it cannot change the destination.
1. Necessary Equipment
Initial screen display • NFC-compatible smartphone
Note 1: Smartphone with a built-in NFC function (OS: Android 2.3.3
or later, excluding Android 3.x).
Note 2: If the NFC-compatible smartphone has an OS version that
3. Press the [ +]/[– ] buttons, destination is displayed on the
is older than Android 4.1.x, download and install the “NFC
vacuum fluorescent display in following order. Easy Connect” application.
Screen display
2. Connection Method
Procedure:
[ +] [– ] [ +] [– ]
1. Turn on the NFC function of the smartphone.
If the NFC-compatible smartphone has an OS version that is
[ +] [– ] [ +] [– ] older than Android 4.1.x, start the “NFC Easy Connect” ap-
plication.
[ +] [– ] [ +] [– ] 2. Press the [1] button to turn the power on.
3. Touch the smartphone to the N-Mark on this unit.
[ +] [– ] [ +] [– ]
[ +] [– ] [ +] [– ]
Setting destination by display:

Screen Destination
Model area
display code 4. When the NFC connection is completed, connected smart-
D ASIA SP6, TH1 South East Asia (Except for India) phone name is displayed on the vacuum fluorescent display.
5. Start the playback of an audio source on the smartphone.
D INDIA E12 India
Note 3: For details, refer to the operating instructions of smartphone.
Middle East (Except for Jordan),
D ME AFC E4, E93
Africa 3. Connection Releasing Method
D OCEANI AU1 Australia, New Zealand Touch the smartphone to the N-Mark on this unit again.
D JAPAN Not used ─
4. Deletion of Pairing Information
D BRAZIL BR1 Brazil
Perform the “COLD RESET” on page 34.
D N AME Not used ─
D LATIN AR2, LA9 Latin America (Except for Brazil)
D RUSSIA RU1 CIS (Except for Moldova)
Europe (Including Ireland, UK),
D EUROPE CEL, CEK
East Europe, Moldova, Jordan
– Continued to the upper right –
6
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
CHECKING THE OPERATION AFTER REPAIR SPREADING OF COMPOUND

After repair completion, connect the “iPhone/iPod”, “Walkman”, When the IC2002 on the MOTHER board is replaced, spread the
“smartphone” etc. corresponding to this unit, and check the opera- compound to the touching portion between the IC2002 and the
tion of playback, recording, charge, etc. heat sink.
NOTE OF REPLACING THE ELECTRICAL PARTS ON – MOTHER Board (Side A) –

EACH BOARD FOR REPAIRING
Among mounted electrical parts on each board, only parts that are IC2002
described in the electrical parts list can be replaced for repairing.
The parts that are not described in the electrical parts list cannot be
replaced with single for repairing. compound
NOTE OF REPLACING THE MOTHER BOARD FOR

REPAIRING
Among mounted parts on the MOTHER board, only parts that are
described in the electrical parts list can be replaced for repairing.
When the parts that are not described in the electrical parts list are
defective, replace the complete mounted board.
In this service manual, the block diagram and printed wiring board
of the MOTHER board are described for reference.
TEST DISCS
Also, when the MOTHER board is replaced, be sure to refer to
Use following TEST DISC when this unit confirms the operation
“DESTINATION SETTING METHOD” and “NFC OPERATION
and checks it.
CHECKING METHOD” on page 6.
• For CD
NOTE OF REPLACING THE PARTY LED, SW LED
Part No. Description
NFC AND MS-476 BOARDS FOR REPAIRING
3-702-101-01 DISC (YEDS-18), TEST
When the PARTY LED, SW LED, NFC and MS-476 boards are
4-225-203-01 DISC (PATD-012), TEST
defective, replace the complete mounted board or the whole parts
J-2501-307-A DISC (HLX-A1), TEST
including the applicable board.
The mounted parts cannot be replaced with single for repairing.
• For DVD SL (Single Layer)
In this service manual, the schematic diagram and printed wiring
board of the PARTY LED, SW LED, NFC and MS-476 boards are
J-6090-069-A DISC (HLX-503), TEST (NTSC)
not described.
Also, when the NFC board is replaced, be sure to refer to “NFC
OPERATION CHECKING METHOD” on page 6.
J-6090-077-A DISC (HLX-506), TEST (PAL)
NOTE OF REPLACING THE SMPS BOARD FOR RE-
• For DVD DL (Double Layer)
PAIRING
When the SMPS board is defective, replace the complete mounted
board.
The mounted parts cannot be replaced with single for repairing.
However, in this service manual, the block diagram, schematic dia-
J-6090-078-A DISC (HLX-507), TEST (PAL)
gram and printed wiring board of the SMPS board are described
for reference.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of sample disc in the
shop is equipped.
It can release the lock function in the following procedure.
Releasing Procedure:
1. Press the [1] button to turn the power on.
2. Press the [FUNCTION] button to select the “DVD/CD” func-
tion.
3. Press two buttons of the [MEGA BASS] and [VOCAL FAD-
ER] simultaneously for 3 seconds.
4. The message “UNLOCKED” is displayed on the vacuum fluo-
rescent display and the disc tray is unlocked.
Note: When “LOCKED” is displayed on the vacuum fluorescent display,
the disc tray lock is not released by turning the power on/off with
the [1] button.
7
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note 1: Refer to “2. DISASSEMBLY” on page 9 or later, after the top panel block is removed, do this work.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
– Left view –
hole
front side
2 Pull out the tray in the

direction of the arrow.
1 Insert the clip etc. in the hole,
– Top view – and push the lever in the direction
of the arrow.
thin wire (clip etc. )
DVD mechanism deck
8 cm or more
front side
hole
tray
CHANGE OF MOTHER BOARD

The MOTHER board has been changed in the midway of production.
When identifying the MOTHER board before changing (Former MB type) and the MOTHER board after changing (New MB type), check
the engraving of MOTHER board or check the serial number on the rear side of this unit.
Note: When replacing the MOTHER board with a new MOTHER board, there is no problem using either the Former MB type or the New MB type.
• Identify by checking the engraving of MOTHER board • Identify by checking the serial number
– MOTHER Board – MOTHER Board Serial number

(Side A) – (Side B) – Destination Former MB type New MB type
AEP 1012850 or smaller 1012851 or larger
UK 1002366 or smaller 1002367 or larger
E4 1001570 or smaller 1001571 or larger
E93 1003000 or smaller 1003001 or larger
AUS 1002659 or smaller 1002660 or larger
RU 1000806 or smaller 1000807 or larger
Former MB type: BR 1005200 or smaller 1005201 or larger
1-983-576-11 SP 1005646 or smaller 1005647 or larger
MB 1BOX L PWB
AR 1005710 or smaller 1005711 or larger
New MB type: TH 1002189 or smaller 1002190 or larger
1-983-189-21 IND 1012150 or smaller 1012151 or larger
MB 1BOX M/L/SL PWB LA 1066113 or smaller 1066114 or larger
Serial number location
– Rear view –
8
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
JIG
When disassembling the unit, use the following
jig for speaker removal.
2-2. SIDE PANEL
(Page 10) Part No. Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
2-3. TOP PANEL BLOCK-1

(Page 11)

(Page 12)
2-16. MIC BOARD
(Page 23)
2-17. PANEL BOARD 2-18. ELECTRET CAP MICROPHONE

(Page 24) (Page 25)
2-19. NFC BOARD 2-20. GESTURE BOARD

(Page 25) (Page 26)
2-5. LOADING PANEL BLOCK 2-7. CDM BLOCK 2-8. FFC HOLDER
(Page 13) (Page 15) (Page 16)
2-6. LOADING PANEL 2-10. REAR PANEL BLOCK 2-9. OPTICAL PICK-UP BLOCK
(Page 14) (Page 18) (CMS-S76RFS7G)
(Page 17)
2-11. PARTY LED BOARD 2-13. CHASSIS BLOCK 2-14. SMPS BOARD
(Page 18) (Page 20) (Page 21)
2-12. DC FAN, 2-21. FRONT PANEL BLOCK-1 2-15. MOTHER BOARD

REAR PANEL (Page 27) (Page 22)
(Page 19)
2-22. FRONT PANEL BLOCK-2 2-24. LOUDSPEAKER (TWEETER)

(Page 28) (Page 30)
2-23. SW LED BOARD, 2-25. LOUDSPEAKER (MIDRANGE)

IR BOARD (Page 31)
(Page 29)
2-26. LOUDSPEAKER
(SUBWOOFER)
2-27. CHASSIS BLOCK SERVICE POSITION
(Page 32)
(Page 33)
2-28. TOP PANEL BLOCK SERVICE POSITION

(Page 33)
9
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Note: Follow the disassembly procedure in the numerical order given.
2-2. SIDE PANEL
1 two screws
(BVTP3 u 8) 3 claw
1 two screws 3 claw

(BVTP3 u 8) 1 screw top side
(BVTP3 u 8)
3 claw
rear side
4 side panel (L)
3 claw 3 claw
left side
3 claw
1 two screws
(BVTP3 u 8)
front side 4 side panel (R)
right side
1 three screws
(BVTP3 u 8)
10
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
• Continued on 2-4 (page 12).
Note 2: Since flexible flat cable (7P) connected to CN120 and flexible flat cable
(7P) connected to CN601 have the same number of cores, be careful not
to mistake the connectors to be connected absolutely. If it connect flexible
flat cable (7P) to the wrong connector, this unit is damaged.
Be sure to check the color of flexible flat cable (7P), before connecting
the flexible flat cable (7P) to the connector. top side
White flexible flat cable (7P): Connect to CN120 on the MOTHER board
Silver flexible flat cable (7P): Connect to CN601 on the MOTHER board
front side
White flexible flat cable (7P)
(from GESTURE board)
Silver flexible flat cable (7P)
(from MIC board)
MOTHER board
CN601 CN120
1 Cut the insulock tie.

Note 1: During reassembly, use new
insulock ties to fasten the
wires back in place as they rear side
were before disassembly.
$(3588.$86(63 4 MIC board wire
2 screw $(3588.$86(63
(BVTP3 u 8) 3 PANEL board wire
0 flexible flat cable (7P) [white] (CN120)

(from GESTURE board) (See Note 2)
9 flexible flat cable (7P) [silver] (CN601)
(from MIC board) (See Note 2)
:LUHVHWWLQJ
2. NG
front side
right side
5 microphone wire connector

(CN3001)
8 PANEL board cable
6 flexible flat cable (6P) (CN105) connector (CN451)
(from NFC board)
$(3588.
microphone microphone 7 flexible flat cable (19P) (CN103) $86(63 rear side
wire wire (from PANEL board)
WireVHWWLQJ
$(3588.$86(63
front side –5LJKWYLHZ– rear side MIC board wire
PANEL board PANEL board wire
cable
The opposite side

is terminal side. MOTHER
board
CN601
(See Note 2)
CN451
The opposite side
is terminal side.
CN103 terminal side
CN3001 CN105
CN120 The opposite side –5LJKWYLHZ– insulock tie
(See Note 2) is terminal side.
11
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
top side
rear side
1 screw
(BVTP3 u 8) 2 three screws
(BVTP3 u 8)
(AEP, RU, UK,

AUS, E4, SP)
1 screw
front side
(BVTP3 u 8)
3 Lift up rear side of the top

panel block in the direction
of the arrow.
4 two claws
top panel block
7 top panel block
(AEP, RU, UK,

AUS, E4, SP)
(AEP, RU,
5 Remove the top panel block UK, AUS,
in the direction of the arrow. E4, SP)
6 PANEL board cable

connector (CN7600)
12
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-5. LOADING PANEL BLOCK
DVD mechanism deck top side
hole
front side
– Left view –
top side
rear side DVD mechanism deck
4 Remove the loading

panel block in the
tray
hole 3 claw
1 Insert the clip etc. in the hole, and

push the lever in the direction of 3 claw
the arrow.
front side
left side lever
clip etc. 5 loading panel block
(8 cm or more) (See Fig. A)
2 Pull out the tray in the
Note about installing the loading panel block

< Fig. A >
OK NG
The gaps at both ends are equal. The gaps at both ends are not equal.
(installed horizontally) (installed at an angle)
tray tray
narrow
wide
loading panel block – Top view – loading panel block – Top view –
13
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-6. LOADING PANEL
0 loading panel
9 hemilon cushion front side

(See Fig. C)
3 Draw the spring (LP)
7 loading cushion out of the two holes.
5 claw
(See Fig. D)
5 claw
8 base loading
1 hemilon
(See Fig. E) 9 hemilon cushion
(See Fig. C)
2 hemilon cushion
(See Fig. B)
4 spring (LP) 6 Remove the base loading
block in the direction of
rear side 1 hemilon the arrow.
(See Fig. E)
1RWHDERXWLQVWDOOLQJWKHVSULQJ/3
OK NG
The spring loading has good balance. The spring loading has poor balance.
rear side rear side
(the center of the spring is centered) (the center of the spring is shifted to
the left or right)
–%RWWRPYLHZ– spring (LP) –%RWWRPYLHZ–

spring (LP)
front side front side
3DVWLQJSRVLWLRQRIWKHKHPLORQFXVKLRQ 3DVWLQJSRVLWLRQRIWKHORDGLQJFXVKLRQ
)LJ%! )LJ'! top side
rear side loading panel block guide line –)URQWYLHZ–
hemilon cushion
loading cushion
base loading
bottom side
–%RWWRPYLHZ– guide line
front side
3DVWLQJSRVLWLRQRIWKHKHPLORQ
)LJ&! rear side )LJ(!
loading panel guide line
–%RWWRPYLHZ–
hemilon cushion guide line Bend.

Bend.
hemilon hemilon hemilon

guide line –,QQHUYLHZ– front side
cushion front side loading panel block
14
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-7. CDM BLOCK
top side 9 CDM block

7 two screws Note 1: When installing the CDM block,
(BVTP3 u 8) boss align the two bosses and two holes.
5 Remove the DC fan cable
from the groove.
'&IDQFDEOHVHWWLQJ boss 4 Remove the DC fan cable

from the coating clip.
Note 2: The DC fan cable must not touch
the heat sink.
–&'0EORFNERWWRPYLHZ–
groove
DC fan cable
2 flexible flat cable (5P)
1 OP cable
(CN303) (from MS-476 board)
connector
(See Fig. F)
(CN402)
(See Fig. F) 3 flexible flat cable (24P) (CN302)
(from optical pick-up block)
front side
(See Fig. F)
hole
8 Remove the CDM block
in the direction of the arrow.
hole
heat sink 6 two screws

MOTHER board
(BVTP3 u 8)
coating clip
right side
rear side
:LUHVHWWLQJ
)LJ)! –5LJKWYLHZ– heat sink
front side rear side
flexible flat cable (24P)

(from optical pick-up block)
flexible flat cable (5P)

(from MS-476 board) terminal side
CN303
OP cable CN302
CN402 terminal side MOTHER board
15
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-8. FFC HOLDER
top side
1 two screws 1 two screws

(BVTP3 u 8) (BVTP3 u 8)
4 DVD mechanism deck block
3DVWLQJSRVLWLRQRIILODPHQWWDSHVXEPDWHULDO
)LJ*!
flexible flat cable
(24P) filament tape
2 (sub material)
rear side
Turn over.
DVD mechanism
deck block
front side
3 CDM bracket block
8 FFC holder (See Fig. H)

Note: When installing the FFC holder,
check that installed firmly
two bosses and claw. 5 filament tape –BRWWRPYLHZ–
(sub material)
(See Fig.G)
flexible flat cable filament tape
hole (5P) (sub material)
6 Remove the FFC holder

7 Draw the flexible flat cable in the direction of the arrow.
out of the hole.
1RWHDERXWLQVWDOOLQJWKH))&KROGHU
5 filament tape boss )LJ+!
(sub material)
(See Fig.G) boss OK NG
rear side
top side
front side claw
DVD mechanism deck block There is no gap. There is a gap.
16
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-9. OPTICAL PICK-UP BLOCK (CMS-S76RFS7G)
2 chuck holder block top side
5 insulator screw
0 insulator
5 insulator screw
qa optical pick-up block 7 connector
(CMS-S76RFS7G)
0 insulator
5 insulator screw
0 insulator
9 MOTHER board connection
5 insulator screw cable connector
Wire setting
0 insulator < Fig. J > rear side
8 flexible flat cable

(24P)
6 Remove the optical pick-up block
in the direction of the arrow. rear side
1 claw
4 three claws
(See Fig. J)
1 claw
1 claw
1 claw
– Bottom view –
front side
1 claw
1 claw
The opposite side rear side
< Fig. K > is terminal side.
front side
3 Draw out the tray.

Note: When you can not draw out the tray,
please refer to “HOW TO OPEN THE
TRAY WHEN POWER SWITCH
TURN OFF” on page 8.
– Top view – MOTHER board

connection cable front side
17
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-10. REAR PANEL BLOCK
front side
3 DC fan cable connector

(CN2001)
6
rear side
5 three screws
(BVTP3 u 8)
right side
4 tapping screw
7 rear panel block (3.5 u 14)
Note: When installing the rear panel block, 5 four screws
be careful not to pinch the DC fan cable. (BVTP3 u 8)
4 tapping screw
(3.5 u 14)
5 screw 2 service connector cap
4 tapping screw (BVTP3 u 8)
(3.5 u 14)
1 screw
(BVTP3 u 8)
2-11. PARTY LED BOARD

2 party lens block
4 PARTY LED board block
,QVWDOODWLRQSRVLWLRQRIWKHSDUW\OLJKWFXVKLRQ
Note 1: When installing the
PARTY LED board top side
boss PARTY LED board LED
block, align the two
bosses and two holes. 1 claw
1 claw
rear side
party light cushion
boss
7 party light cushion
hole 5 screw
(BVTP2.6 u 8)
5 screw
(BVTP2.6 u 8) 8 PARTY LED board
Note 2: When installing the
hole PARTY LED board,
align the three bosses
hole
and three holes.
hole
3 two screws front side
(BVTP2.6 u 8) hole
rear panel block

boss
boss
boss
Turn over. 6 party LED bracket
18
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-12. DC FAN, REAR PANEL
3DVWLQJSRVLWLRQRIWKHKHPLORQ
hemilon Fold. Fold.

top side hemilon top side
–2XWHUYLHZ– –2XWHUYLHZ–
guide line rear panel guide line rear panel
hemilon hemilon
top side
rear panel
–,QQHUYLHZ–
1 two screws
(BVTP3 u 8) 4 hemilon
4 hemilon
1 screw
(BVTP3 u 8)
,QVWDOODWLRQSRVLWLRQRIWKHIDQFXVKLRQ
3 fan cushion
guide line fan cushion
3 fan cushion
1 screw
(BVTP3 u 8)
5 rear panel
3 two fan
cushions
2 DC fan
Note: When installing the DC fan,
be careful not to pinch the
DC fan cable.
19
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-13. CHASSIS BLOCK
front side
left side
1 IR board cable connector

(CN127)
2 SW LED board cable connector rear side

(CN104)
3 speaker cable connector

5 claw 5 claw (CN2021)
4 three tapping screws

(3.5 u 14)
4 tapping screw
(3.5 u 14)
– Right view – – Left view –
4 tapping screw
(3.5 u 14) 7 chassis block
20
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-14. SMPS BOARD
Note 1: Make sure perform discharge processing before removing the

SMPS board. For the discharge processing method, refer to
“CAPACITOR ELECTRICAL DISCHARGE PROCESS-
ING” on page 5.
2 SMPS board cable 3 MOTHER board cable

connector (CN001) connector (CN6500)
(See Note 1) (See Note 1)
1 Remove the two cables

from the coating clip.
(See Fig. L)
front side
Installation direction for

chassis block
the coating clip.
rear side
4 screw
(BVTP3 u 8)
:LUHVHWWLQJ
< Fig. L > 4 five screws
5 coating clip (BVTP3 u 8)
CN001 –7RSYLHZ– front side
hole
CN6500 6 SMPS board

Note 2: When installing the SMPS
board, align the two ribs
and two holes.
MOTHER SMPS board
board hole
SMPS board cable
MOTHER board cable rib
rib
coating clip
21
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-15. MOTHER BOARD
Note 1: Make sure perform discharge processing before removing the Note 2: When the MOTHER board is replaced, refer to “DESTI-
MOTHER board. For the discharge processing method, refer NATION SETTING METHOD” and “NFC OPERATION
to “CAPACITOR ELECTRICAL DISCHARGE PROCESS- CHECKING METHOD” on page 6.
ING” on page 5.
3 MOTHER board cable :LUHVHWWLQJ

2 SMPS board cable connector (CN6500) < Fig. M >
connector (CN001) (See Note 1)
CN001 – Top view – front side
(See Note 1)
1 Remove the two cables

6 six screws from the coating clip.
(BVTP3 u 8) (See Fig. M)
CN6500
front side MOTHER SMPS board

board
SMPS board cable
chassis block MOTHER board cable
rear side
5 screw
4 filament tape
(P3 u 8)
(sub material)
(See Fig. N)
4 filament tape
(sub material) coating clip
(See Fig. N)
qa MOTHER board (See Note 2)
Note 3: When installing the MOTHER board,
:LUHVHWWLQJ align the two ribs and two holes.
< Fig. N > hole
MOTHER board 0 MOTHER board cable
connector (CN2007)
SMPS board
hole
7
MOTHER board
–5HDUYLHZ– cable
hole
MOTHER board
– Bottom view –
cable
8 Draw the connector
and jack out of the
hole in chassis.
rib
front side
9 Draw the MOTHER
filament tape filament tape rib
board cable out of
(sub material) (sub material) the hole in chassis.
(See Fig. N)
hole
22
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
2-16. MIC BOARD
2 three screws Note 2: When connecting, be sure to connect to CN601 on the

(BVTP2.6 u 8) MOTHER board.
If this flexible flat cable (7P) is connected to a connector
4 MIC board block other than CN601, this unit is damaged.
Note 1: When installing the MIC
board block, align the two
bosses and two holes. 7 MIC board
[silver] (CN7701)
hole
3 Draw the jack hole 3 Draw the jack
out of the hole.
out of the hole.
1 Remove the wire from

the coating clip.
front side
5 filament tape
(sub material)
)OH[LEOHIODWFDEOHVHWWLQJ
The opposite side filament tape
rear side CN7701 is terminal side. (sub material)
top panel block
two bosses
two holes
top side
MIC board
$(3588. flexible flat cable
$86(63 (7P) [silver]
:LUHVHWWLQJ
$(3588.$86(63 (%5$57+,1'/$
PANEL board PANEL board
cable PANEL board
–%RWWRPYLHZ– wire –%RWWRPYLHZ– MIC board
cable
MIC
board coating
clip
front side front side
coating clip PANEL board PANEL board
23
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
2-17. PANEL BOARD
3 flexible flat cable (7P) [white]

(CN7500) Note 2: When connecting, be sure to connect to CN120 on the
MOTHER board.
2 filament tape If this flexible flat cable (7P) is connected to a connector
terminal side (sub material) other than CN120, this unit is damaged.
(See Fig. O)
)OH[LEOHIODWFDEOHVHWWLQJ
front side
flexible flat cable flexible flat cable
(7P) [white] (19P)
1 Remove the flexible
flat cable from the
coating clip. PANEL
board
rear side
front side
coating clip –%RWWRPYLHZ–
top side top panel block
7 PANEL board block

Note 1: When installing the PANEL board block,
align the two bosses and two holes. 9 flexible flat cable (19P)
(CN7007)
4 eight screws
(BVTP2.6 u 8) 4 eight screws
(BVTP2.6 u 8)
0 hemilon
4 screw
(BVTP2.6 u 8)
Turn over. hole
hole
5 coating
hole clip
6
5 coating clip
4 screw
(BVTP2.6 u 8) qa PANEL board
8 Draw the flexible flat
cable out of the hole.
boss )OH[LEOHIODWFDEOHVHWWLQJ Pass the flexible flat cable

flexible flat cable (19P) into the hole.
–7RSYLHZ–
boss rear side
3DVWLQJSRVLWLRQRIWKHILODPHQWWDSHVXEPDWHULDO
)LJ2!
–%RWWRPYLHZ– PANEL board
hole
flexible flat cable
(7P) [white] PANEL board
CN7007 Bend.
terminal side
GESTURE board
front side filament tape

(sub material)
24
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-18. ELECTRET CAP MICROPHONE
1 screw
(BVTP2.6 u 8) 0LFURSKRQHZLUHVHWWLQJ
electret cap
microphone microphone wire
2 MIC COVER board
Note: When installing the MIC COVER front side
board, align the boss and hole.
hole
4 electret cap
microphone
MIC COVER
3
board
front side
–%RWWRPYLHZ–
boss
rear side
top side
top panel block
2-19. NFC BOARD
Note: When the NFC board is replaced, refer to “NFC OPERATION

CHECKING METHOD” on page 6.
1 screw 3DVWLQJSRVLWLRQRIWKHILODPHQWWDSHVXEPDWHULDO

(BVTP2.6 u 8) filament tape
NFC board (sub material)
2 guitar button assy 3 filament tape

(sub material)
flexible flat cable
(6P)
0 mm (+ 2, - 0 mm)
rear side
–,QQHUYLHZ–
NFC tape
7 NFC board (See Note)
top panel block
(CN001)
front side
6 NFC tape
terminal side
4 Peel the NFC board block

off of the top panel block.
rear side
top side
25
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-20. GESTURE BOARD
2 start button
6 DJ button
hole Note 1: When installing the DJ button,
align the four bosses and four
holes.
hole
hole
hole
hole
3 screw
5
(BVTP2.6 u 8)
hole hole 8 GESTURE board
Note 2: When installing the GESTURE
1 hole board, align the six bosses and
4 fiesta button assy six holes.
hole
hole
boss
7 boss
boss
boss
front side
boss rear side
top side boss
top panel block
26
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-21. FRONT PANEL BLOCK-1

• Continued on 2-22 (page 28).
,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUFDEOHWHUPLQDO
Note 1: When connecting the speaker cable terminal to
the tweeter (L-ch), take care for the direction of
the terminal and connect it.
OK
OK
NG NG
tweeter
(L-ch)
top side
1 terminal
(wide side) top side
1 terminal
[yellow] (narrow side)
1 terminal [black]
(narrow side)
[black]
tweeter
1 terminal (L-ch)
(wide side)
[yellow]
–,QQHUYLHZ–
[yellow] [black]
front side
,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUFDEOHWHUPLQDO
Note 2: When connecting the speaker cable terminal to
the tweeter (R-ch), take care for the direction of
the terminal and connect it.
OK
OK
NG NG
rear side
tweeter tweeter
(R-ch) (R-ch)
top side
–,QQHUYLHZ–
[yellow] [black]
27
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-22. FRONT PANEL BLOCK-2
3
6
front panel block

4
2 While moving the jig
in the direction of the
arrow, remove nine top side
bosses.
soft cloth, etc.
front side
qf
Turn over.
qs
bottom side
speaker total nine bosses 0

qd
cabinet
1 Insert the jig into the space and slowly qa

remove the front panel block. top side
Note 1: When using a jig, please work
carefully so as not to damage 9 While moving the jig
the front panel block and in the direction of the
speaker cabinet. arrow, remove nine
bosses.
front side
qh front panel block
Note 2: When installing the front panel block,
peel off the used bond and apply a new
bond, then install the front panel assy.
bottom side
total nine bosses
8 Insert the jig into the space and slowly
remove the front panel block.
Note 1: When using a jig, please work
carefully so as not to damage
the front panel block and
speaker cabinet.
total eighteen bosses

qg Remove the front panel block
28
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-23. SW LED BOARD, IR BOARD
0 IR board
Note 2: When installing the IR board,
6:/('ERDUGFDEOHVHWWLQJ align the two bosses and two
holes.
3DVWLQJSRVLWLRQRIWKHKHPLORQ qa IR window
)LJ3! Note 3: When installing the IR window,
top side align the two bosses and two
SW LED board hole holes.
cable hole total thirteen
9 two screws grooves
hemilon (BVTP2.6 u 8)
hole
boss
hole boss
top side front panel block
top side 1 hemilon

(See Fig. P) front side
2 Draw the SW LED

board cable out of
the groove.
total thirteen
grooves
SW LED
board
cable
boss
rear side
boss
hole
4
bottom hole
side 3 two screws
–)URQWSDQHOEORFNLQQHUYLHZ– (BVTP2.6 u 8)
8 SW LED
board
6 screw
(BVTP2.6 u 8)
5 SW LED board 7 SPK LED bracket
cable connector Note 1: When installing the SPK LED
(CN7651) bracket, align the two bosses
and two holes.
29
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-24. LOUDSPEAKER (TWEETER)
top side
front side
3 loudspeaker
2
(tweeter: R-ch)
(See Fig. Q)
1 two screws rear side

(BVTP3.5 u 10) 3 loudspeaker
(tweeter: L-ch)
(See Fig. Q)
2
1 two screws
(BVTP3.5 u 10)
,QVWDOODWLRQGLUHFWLRQIRUWKHWZHHWHU
)LJ4!
Note: When installing the tweeter, make the position
of terminals as shown in the figure below.
top side
terminals position terminals position
front panel block
tweeter (R-ch) tweeter (L-ch)

–)URQWSDQHOEORFNLQQHUYLHZ–
30
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-25. LOUDSPEAKER (MIDRANGE)

Note 1: The left and right loudspeakers can be removed using the same procedure.
This explanation uses illustrations from the left side.
loudspeaker
(midrange: R-ch)
top side
rear side
3 terminal
2 Remove the midrange (narrow side)
(L-ch) in the direction [black]
of the arrow.
terminal
1 four tapping screws

(3.5 u 14) 3 terminal
(wide side)
[red]
4 loudspeaker
(midrange: L-ch)
,QVWDOODWLRQGLUHFWLRQIRUWKHPLGUDQJH front side

Note 2: When installing the midrange, make the position
of terminals as shown in the figure below.
top side
midrange midrange
(L-ch) (R-ch)
speaker cabinet block
terminals terminals
position position ,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUFDEOHWHUPLQDO
Note 3: When connecting the speaker cable terminal to the midrange (L-ch),
take care for the direction of the terminal and connect it.
midrange (L-ch)
OK NG OK NG
top side
– Front view – terminal

(narrow side)
[black] terminal
(wide side)
[red]
31
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2-26. LOUDSPEAKER (SUBWOOFER)
bottom side
rear side
speaker cabinet block

2 Remove the subwoofer
1 tapping screw
(BVTP4 u 20)
1 tapping screw
(BVTP4 u 20)
4 loudspeaker top side

(subwoofer)
3 terminal
1 four screws
(narrow side)
(BVTP4 u 20)
[black]
3 terminal soft cloth, etc.
(wide side)
[gray]
1 tapping screw
1 tapping screw (BVTP4 u 20)
(BVTP4 u 20)
,QVWDOODWLRQGLUHFWLRQIRUWKHVXEZRRIHU Installation direction for the speaker cable terminal

Note 1: When installing the subwoofer, make the position Note 2: When connecting the speaker cable terminal to the subwoofer,
of terminals as shown in the figure below. take care for the direction of the terminal and connect it.
subwoofer
OK NG
top side
terminals position OK NG
terminal
(wide side)
[gray]
terminal
(narrow side)
subwoofer
[black] top side
– Front view –
32
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
2-27. CHASSIS BLOCK SERVICE POSITION
top panel block
IR board
(AEP, RU, UK,
AUS, E4, SP) insulating sheet
CDM block
stand
stand
DC fan
MOTHER board
SMPS board
2-28. TOP PANEL BLOCK SERVICE POSITION
MIC board
insulating sheet
rear side
GESTURE board
PARTY LED board
PANEL board
front side
stand
33
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 3
TEST MODE
USER RESET VERSION DISPLAY
It can reset all preset data back to initial conditions excluding DVD It can check the software version.
setup menu settings.
Procedure (For the main unit operation):
Procedure: 1. Press the [1] button to turn the power on.
1. Set to the demonstration mode or press the [1] button to turn 2. Press two buttons of the [MEGA BASS] and [– TUNING .]
the power on. simultaneously for 3 seconds.
2. Press two buttons of the [MEGA BASS] and [GUITAR] simul- 3. The SC micom/BT micom software version, DVD micom
taneously for 3 seconds. software version are displayed on the vacuum fluorescent dis-
3. The message “RESET” is displayed on the vacuum fluorescent play, then becomes the demonstration mode.
display, then becomes the demonstration mode.
SC micom/BT micom software version
Screen display
SC BT
demonstration mode DVD micom software version
DISC THEFT PREVENTION

It can be unable to take sample disc out of disc tray in the shop. demonstration mode
(Displayed values in the above figure are example)
Procedure:
1. Press the [1] button to turn the power on. Procedure (For the remote commander operation):
2. Press the [FUNCTION] button to turn the “DVD/CD” func- 1. Press the [1] button to turn the power on.
tion. 2. Press the [OPTIONS] button to display the options menu.
3. Press the [Z] button to open the disc tray and set the disc. 3. Press the [v]/[V] buttons to select the “SYSTEM”, and press
4. Press the [Z] button to close the disc tray. the [ ] button.
5. Press two buttons of the [MEGA BASS] and [VOCAL FAD- 4. Press the [v]/[V] buttons to select the “VERSION”, and press
ER] simultaneously for 3 seconds. the [ ] button.
6. The message “LOCKED” is displayed on the vacuum fluores- 5. The SC micom/BT micom software version are displayed on
cent display and the disc tray is locked. the vacuum fluorescent display.
(Even if pressing the [Z] button, the message “LOCKED” is
displayed on the vacuum fluorescent display and the disc tray Screen display
is locked)
Screen display SC BT
6. Press the [V] button.

Releasing method:
7. The DVD micom software version is displayed on the vacuum
1. Press two buttons of the [MEGA BASS] and [VOCAL FAD-
fluorescent display.
ER] simultaneously for 3 seconds.
2. The message “UNLOCKED” is displayed on the vacuum fluo- Screen display
rescent display and the disc tray is unlocked.
Releasing method (For the remote commander operation):

Press the [OPTIONS] button, and return to the normal mode.
COLD RESET
It can reset all preset data back to initial conditions included DVD
firmware initialization. Execute this mode when returning the this
unit to the customer.
Procedure:
1. Set to the demonstration mode or press the [1] button to turn
the power on.
2. Press two buttons of the [x] and [MIC/GUITAR LEVEL +]
simultaneously for 3 seconds.
3. The message “COLD RST” is displayed on the vacuum fluo-
rescent display, then becomes the demonstration mode.
Screen display
demonstration mode
34
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
PANEL TEST MODE 6. Each time [ +] button is pressed, the display changes destina-
It can check the vacuum fluorescent display, LEDs, model name, tion → serial number → SC version → MTK version → BT
destination, buttons and gesture control sensor. version → BTE version → PF version → SUB version this
order, and returns to the model name display.
Procedure:
1. Set to the demonstration mode or press the [1] button to turn
the power on. Model name MTK version
2. Press two buttons of the [x] and [MIC/GUITAR LEVEL –]
simultaneously for 3 seconds.
3. It enters the panel test mode, and all segments on the vacuum Destination BT version
fluorescent display and all LEDs light up.
Screen display Serial number BTE version

NTSC VIDEO WIRED P.CHAIN
FLDR SHUF ST L R SCORE
DD 1 BASS DJ
NX HDMI SLEEP 2 # %
4. Each time the [ ] button on the remote commander is pressed, SC version PF version
the screen display is changed in order as follows.
NTSC VIDEO
FLDR SHUF
WIRED P.CHAIN
ST L R SCORE
All segments and all SUB version
DD 1 BASS DJ
NX HDMI SLEEP 2 # % LEDs turn on
NTSC VIDEO
FLDR SHUF 1st half of segments, (Displayed values in the above figure are example)
DD 1
NX HDMI
[MEGA BASS] indicator
and Subwoofer light
(red) turn on Destination Display
WIRED P.CHAIN 2nd half of segments, AEP, UK models (CEL, CEK) EUROPE
ST L R SCORE
BASS DJ
SLEEP 2 # % [GUITAR]/[GESTURE ON/ RU model (RU1) RUSSIA
OFF] indicators and Party/
AUS model (AU1) OCEANIA
Subwoofer lights (green)
turn on E4, E93 models (E4, E93) ME AFC
NTSC VIDEO
FLDR SHUF
WIRED P.CHAIN
ST L R SCORE
All segments, BR model (BR1) BRAZIL
DD 1 BASS DJ
NX HDMI SLEEP 2 # % [BLUETOOTH] indicator SP, TH models (SP6, TH1) SE ASIA
and Party/Subwoofer
lights (blue) turn on AR, LA models (AR2, LA9) LATIN
All segments and all IND model (E12) INDIA

LEDs turn off
7. When pressing the [x] button while the each version is dis-
5. When pressing the [ +] button, the model name is displayed played, month and day of the software creation is displayed on
on the vacuum fluorescent display. the vacuum fluorescent display. When pressing the [x] button
again, the display returns to the each version display.
Screen display
Screen display
8. When pressing the [– ] button, “K 0” is displayed on the

vacuum fluorescent display.
Screen display
9. Each time a button is touched, “K 0” value increases. Buttons

once pressed are not counted.
When pressing the all buttons, “K30” and “OK” are alternately
displayed on the vacuum fluorescent display.
Screen display
– Continued on next page –
35
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
10. When the operation of swiping on the gesture control sensor, SHOP FRONT DEMO
shown in the following figure, will appear display correspond- The demo mode can be performed.
ing to the operation. (This mode is used by shop front)
Note: Do not touch or contact to the gesture control sensor when you per-
form the swiping motion. Procedure:
2. Press the [FUNCTION] button to select the “DVD/CD” or
“USB” function, and set the media according to the function.
3. Press two buttons of the [x] and [MIC ECHO] simultaneously
for 5 seconds.
4. The message “AutoPLAY” is displayed on the vacuum fluo-
Screen display (Right to left) Screen display (Left to right) rescent display.
Screen display
5. Press the [– TUNING .] or [TUNING + >] button to

select either “AutoPLAY” or “AutoSTOP” in the demo mode,
then press the [N] button to decision.
Screen display (Bottom to top) Screen display (Bottom to top) Screen display
or
(Displayed characters in the above figure are example)
Releasing method:
Press two buttons of the [x] and [MIC/GUITAR LEVEL –] simul- 6. The message “10 MIN” is displayed on the vacuum fluorescent
taneously for 3 seconds, and return to the normal mode. display.
Screen display
7. Press the [– TUNING .] or [TUNING + >] button to

auto play or auto stop timer value (01 MIN to 20 MIN) setting,
then press the [N] button to decision.
8. This unit is rebooted. It enters the demo mode, “* DEMO *”
and current function state are alternately displayed on the vac-
uum fluorescent display.
(When the “AutoPLAY” has been selected in step 5, playback
starts automatically)
Screen display
current function state display
9. When the “AutoPLAY” has been selected in step 5, even if

stopping the playback, playback starts automatically after the
setting time.
When the “AutoSTOP” has been selected in step 5, even if
starting the playback, playback stops automatically after the
setting time.
(Even if pressing the [Z] button, the disc tray is locked and
cannot be opened)
Releasing method:
Press two buttons of the [x] and [MIC ECHO] simultaneously for
5 seconds.
Note: The demo mode does not release by unplug the power supply cord.
36
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 4
ELECTRICAL CHECKS
TUNER SECTION 0 dB = 1 V DVD/CD SECTION
FM AUTO STOP CHECK Note:

1. DVD/CD block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
signal
generator ed.
unit 3. Use an oscilloscope with more than 10 M impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following check.
Procedure:
1. Press the [1] button to turn the power on. RF SIGNAL CHECK
2. Input the following signal from signal generator to FM antenna
input directly. oscilloscope
(DC range)
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz MOTHER board

Deviation : 75 kHz
CN302 pin 17 (RF) +
Modulation : 1 kHz CN302 pin 1 (GND) –
ANT input : 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the unit. Procedure:
You cannot use video cable for checking. 1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302
Use signal generator whose output impedance is 75 ohm. pin 1 (GND) on the MOTHER board.
3. Press the [FUNCTION] button to select the “TUNER FM” 3. Press the [FUNCTION] button to select the “DVD/CD” func-
function and scan the input FM signal with automatic scan- tion.
ning. 4. Press the [Z] button to open the disc tray and set the disc
4. Confirm that input frequency of A, B and C detected and auto- (YEDS-18).
matic scanning stops. 5. Press the [Z] button to close the disc tray.
6. Press the [N] button to playback.
When the station signal is received in good condition, automatic 7. Confirm that oscilloscope waveform is as shown in the figure
scanning stops. below. (eye pattern)
A good eye pattern means that the diamond shape () in the
center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level: 1.0 ± 0.25 Vp-p
Connection Location:
– MOTHER Board (Side A) –
IC2001
CN302 pin 1 (GND)
IC109 pin 17 (RF)
37
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 5
TROUBLESHOOTING
1. Optical Pick-up Block (CMS-S76RFS7G1/S76RFS7GP) (OP1) Diagnosis Flow
Remove the top panel, turn the

power on, close the disc tray and
set in the state that optical pick-up
block can see.
The optical pick-up block moves to No No

The voltage of the following is 3.3 V. The voltage of the following is 3.3 V.
the inner circumference.
MOTHER board: JL049 MOTHER board: JL071 (IC009: pin 14)
(Visual check)
Yes
Yes
Check the circuit of area surrounding
IC401 pin 17 (VOLD+), pin 18 (VOLDí)
The SL+/SLí signal is outputted to the No on the MOTHER board.
CN402 pin 4 (SL+), pin 3 (SLí) on the
MOTHER board.
IC301 pin 13 (FMO) on the MOTHER
Yes board.
Replace the optical pick-up block because

sled motor has the problem.

IC401 pin 11 (VOSL+), pin 12 (VOSLí)
The SP+/SPí signal is outputted to the No
The spindle motor rotates. No on the MOTHER board.
CN402 pin 2 (SP+), pin 1 (SPí) on the
(Visual check) Check the circuit of area surrounding
MOTHER board.
IC301 pin 12 (DMO) on the MOTHER
Yes Yes board.

spindle motor has the problem.

IC401 pin 14 (VOFC+), pin 13 (VOFCí)
The optical pick-up block does the The FCS+/FCSí signal is outputted to the No
No on the MOTHER board.
focus search. CN302 pin 23 (FCS+), pin 24 (FCSí) on
(Visual check) the MOTHER board.
IC301 pin 17 (FOO) on the MOTHER
Yes Yes board.

optical pick-up block has the problem.
– Continued on page 39 –
38
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
– From page 38 –

No It is outputted 2 V to the CN302 pin 6 No Q402 on the MOTHER board.
The laser diode emits the light.
(FE_LD_CD (780)) on the MOTHER Check the circuit of area surrounding
(Visual check)
board. IC301 pin 9 (LDO1) on the MOTHER
Yes board.
Yes
Set the test disc (YEDS-18) on the

Replace the optical pick-up block.
disc tray and playback it.
Yes
The following standard value of RF

signal is outputted to the CN302 No
Perform the lens cleaning.
pin 17 (RF) on the MOTHER board.
RF level = 1.0 ± 0.25 Vp-p
Yes
Yes
The following standard value of RF signal

is outputted to the CN302 pin 17 (RF) on No
Replace the optical pick-up block.
the MOTHER board.
RF level = 1.0 ± 0.25 Vp-p
Yes
There is no problem when

No
performing the playback test of long Replace the optical pick-up block.
time (60 minutes).
The sound skip does not happen.
Yes
End
39
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
2. MOTHER Board Mount Amplifier Diagnosis Flow
2-1. “PROTECT3” is displayed on the vacuum fluorescent display after turning the power on
“PROTECT3” is displayed on the vacuum

fluorescent display after turning the
power on.
Yes
“PROTECT3” is not displayed on the

No IC2002 pin 27, 28 (OUT_D), 32 (OUT_C), No
vacuum fluorescent display, when MOTHER board has been damaged.
35 (OUT_B) and 39, 40 (OUT_A) on the
removing the speaker (SP1 to SP5) Replace the MOTHER board.
MOTHER board is short to GND.
and turning the power on.
Yes
Yes
Check and replace the speaker Replace the IC2002 on the MOTHER
(SP1 to SP5). board.
2-2. The sound is not outputted
The sound is not outputted.
Yes
The audio signal is inputted to IC2001 pin 24 No MOTHER board has been damaged.
(SDIN1) and 25 (SDIN2) on the MOTHER board. Replace the MOTHER board.
Yes
The PWM signal is outputted from IC2001 No

pin 39 (PWM_P_1), 41 (PWM_P_2), Replace the IC2001 on the MOTHER board.
48 (PWM_M_ 4), 49 (PWM_P_ 4).
Yes
The audio signal is outputted from IC2002

pin 32 (for L-ch speaker), pin 27, 28 (for R-ch No
Replace the IC2002 on the MOTHER board.
speaker) and pin 35, 39, 40 (for subwoofer) on
the MOTHER board.
Yes
MOTHER board has been damaged.

Replace the MOTHER board.
40
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
3. MOTHER Board Mount Diagnosis Flow (Except Amplifier)
Connect the power supply cord.
The voltage of the following is outputted. No Check the connection of connector

(CN001). When there is not problem to
Standby Demo mode Power on the connection, check the SMPS board.
CN001:
pin 1, (AUDIO_+13V/+16V) 17.4 V ± 5 % 17.4 V ± 5 % 17.4 V ± 5 %
pin 3, 4 (M/D_+13V/+16V)
Yes
The voltage of the following is outputted between the each terminal of IC. No When there is problem, replace the
problematic IC.
IC Voltage Pin name Pin number Test point
SW1 3 JL069
5V
PGND1 4
IC001
SW2 14 JL070
5.2 V
PGND2 13
SW1 3 JL072
1.2 V
PGND1 4
IC009
SW2 14 JL071
3.3 V
PGND2 13
VOUT 2 JL073
IC008 12 V
GND 3
VOUT 2 JL047
IC004 9V
GND 3
VOUT 2 JL048
IC006 5V
GND 3
OUT 1 JL137
IC002 12 V
GND 3
VOUT 4 JL1003
IC1000 5V
GND 2
VOUT 3 CL395
IC305 3.3 V
GND 2
Yes
End
41
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
4 SMPS Board Mount Diagnosis Flow
Connect the power supply cord.
The voltage of the following is outputted. No Check whether the state of the power
supply cord and AC outlet are normal.
Standby Demo mode Power on If there are no problems, check the
NO6501: pin 9 (MAIN ON) Low (0 V) Hi (3.3 V) Hi (3.3 V) surrounding circuit for MAIN ON signal
output on the MOTHER board.
Yes
The voltage of the following is outputted. No Check the following 2 points. No

)XVHV))KDYHEHHQQRW
Standby Demo mode Power on opened.
NO6501: $&SRZHUVXSSO\YROWDJHKDVEHHQ
pin 1 (A-supply), 17.4 V ± 5 % 17.4 V ± 5 % 17.4 V ± 5 % applied to the varistor (VR6000).
pin 4, 5 (M-supply) Yes
CN6500: pin 6 to 9 (V1) 58.5 V ± 5 % 58.5 V ± 5 % 58.5 V ± 5 %
5HSODFHWKHIXVHV))DQG
Yes varistor (VR6000), and check the voltage
again.
End
Replace the SMPS board.
42
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM - SERVO/USB/VIDEO Section -
OP1
OPTICAL PICK-UP BLOCK RF AMP, SERVO/AUDIO/VIDEO PROCESSOR
(CMS-S76RFS7G1/S76RFS7GP) IC301 ASDATA0, MTK-BCK, MTK-LRCK,
MTK-MCK, ARC_SPDIF
ASDATA0
RF 119 RFIP ASDATA0 115
MTK-BCK
>001B
ARC_SPDIF
ABCK 110
VOA/A 125 RFC MTK-LRCK (Page 44)
ALRCK 114
VOB/B 124 RFB MTK-MCK
ACLK 109
VOC/C 123 RFA
VOD/D 126 RFD
128 FE_DVD_IOP-RFF
127 FE_CD_IOP-RFE
TX0P 88 7 DATA0+
VC 5 V20
TX0N 87 9 DATA0–
PD 8 MDI1
TX1P 91 4 DATA1+
AUTOMATIC POWER TX1N 90 6 DATA1–
FE_LD_CD (780) CONTROL (FOR CD) DVDD_3.3V
Q402 TX2P 94 1 DATA2+
TX2N 93 3 DATA2– CN1000
9 LDO1 (TV)
TXCP 85 10 CLOCK+
ARC
AUTOMATIC POWER TXCN 84 12 CLOCK– HDIM OUT
FE_LD_DVD (650) CONTROL (FOR DVD)
Q401 BUFFER
14 ARC
IC1001
10 LDO2
HDMI_SDA 29 16 SDA (5V)
MSW 18 MSW HDMI_SCL 28 15 SCL (5V)
CD_VR (780) 14 CD_VR HPLG 81 19 HOT PLUG DET

DVD_VR (650) 15 DVD_VR
13 CEC
NC 120 RFIN/OPOUT/GPI36
J601 (1/3)
CVBS 98 VIDEO
OUT
USB SWITCH
IC453
3 CN7801
USB_DP 19 5 HSD1+ D+ 1 D+ REC/PLAY
2 5V 1A
USB_DM 20 4 HSD1– D– 2 D–
4 XTALO
X301
SERIAL FLASH 7 HSD2+
27MHz
3 XTALI IC302
6 HSD2D–
SF_DO 25 2 DO (IO1)
S
SF_DI 26 5 DI (IO0)
10
FOCUS/TRACKING COIL DRIVE, SF_CK 27 6 CLK
SPINDLE/SLED/LOADING MOTOR DRIVE SF_CS_ 24 1 CS
IC401 SIGNAL PATH
: AUDIO
SP+ 11 VOSL+
VINSL+ 4 12 DMO SD-RAM : DISC PLAY
SP– 12 VOSL–
IC305
SL+ 17 VOLD+ : VIDEO
VINLD 23 13 FMO RD0 – RD15 DQ0 – DQ15
SL– 18 VOLD–
: USB
TRK+ 16 VOTK– RA0 – RA11 A0 – A11
VINTK 26 16 TRO
TRK– 15 VOTK+
BA0 72 20 BA0
FCS+ 14 VOFC+ BA1 73 21 BA1
VINFC 1 17 FOO
FCS– 13 VOFC– RCLK 60 38 CLK
RWE# 68 16 WE
MUTE 28 108 PAPLLCAP/GPIO35
CAS# 69 17 CAS
BIAS 27 6 V14 RAS# 70 18 RAS
GPIO13
DQM0 49 15 LDQM
PRST_
IFSDO
IFSCK
IFCS_
IFSDI
DQM1 59 39 UDQM
35 38 37 34 36 32
22 20 17 19 104 14
MTK-BUSY
MTK-RESET
MTK-SDO
MTK-SDI
MTK-CLK
MTK-XIFCS
CEC-IN 10 CEC DATA SWITCH

MS-476 BOARD CEC-OUT 15 Q1000 – 1002, 1005
LOAD+ 10 VOTR+ FWD 6 8 CD-MOTOR+ DP0 151

LOAD– 9 VOTR– REV 7 3 CD-MOTOR– DM0 150
USB-HOST-SEL 106
TRAY-IN 12 CDM-LOAD-SW
TRAY-OUT 13 CDM-UNLOAD-SW
AUDIO DSP, SYSTEM CONTROLLER

IC109 (1/4)
MHC-V41D
43 43
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
6-2. BLOCK DIAGRAM - AUDIO Section -

A/D CONVERTER
ASDATA0, MTK-BCK, MTK-ALRCK, IC606
MTK-MCK, ARC_SPDIF
MTK-MCK
>001B 6 SCK
DIGITAL AUDIO INTERFACE RECEIVER
(Page 43)
IC904
ALRCK_I1 9 7 LRCK
ASDATA0 AUDIO DSP, SYSTEM CONTROLLER
28 RXIN7 ABCK_I1 8 8 BCK VINR 14 R-CH
MTK-BCK IC109 (2/4) DOUT1, DOUT2, ARAGON-BCK3,
30 ABCK_IO ADIN_1 10 9 DOUT
FM TUNER TUNER/BLUETOOTH SELECTOR MTK-LRCK VINL 13 ARAGON-LRCK3, ARAGON-MCK
29 ALRCK_IO ARAGON-BCK3
CN9000
IC902 IC905 ARC_SPDIF
32 RXIN3
>002B
DOUT2
FM 2 DOUT 17 28 SSI3-DI SSI2-DO (FR) 40 (Page 45)
RF 1 FRF1 IISD 14 11 3A
ANTENNA 3Y 9 14 ADIN_2 BCK 19 24 SSI3_BCKO
10 3B DOUT1
LRCK 18 26 SSI3_LRCKO SSI1_DO (TW) 54
17 X2 BCLK 12 5 2A
X900 2Y 7 12 ABCK_I2 ARAGON-LRCK3
6 2B SDA 24
12MHz
16 X1 LRCK 13 2 1A SCL 25
1Y 4 13 ALRCK_I2
3 1B INT0 1 42 DIR-INT0
DA 11 40 XTO INT1 2 41 DIR-INT1
SELECT X602
CK 8 RST 34 38 DIR-RESET
1 24.576MHz
IIC/RDSI 6 39 XTI
4 MPIO_A1
108 BT-TUNER-SEL
126 DIR-CP-TUNER-SDA
CP3000
125 DIR-CP-TUNER-SCL
BLUETOOTH MODULE
45 ST-RDS
MIC1 10 MIC_BIAS DT0 4

SCLK0 3
RFS0 2
BUS BUFFER
HCI_TXD 19 65 BT-RxD
IC102 (1/2)
RESET
>003B
MFI HCI_RXD 18 133 BT-TxD
(Page 46)
IC3000 MFB 26 164 MFB
EAN 32 165 EAN
SDA 2 16 CP_SDA P2_0 41 124 P20
SCL 6 15 CP_SCL P2_7 42 131 P27
RST 7 29 CP_RST RST_N 13 113 BT-RESET
RESET SIGNAL
GENERATOR BT_3.3V
IC3001 A/D CONVERTER
IC605
J7700
MIC 1 14 VINR
DOUT 9 33 SSI0_DI (MIC)
13 VINL
MIC AMP BCK 8 29 SSI0_BCKO
IC7700 LRCK 7 30 SSI0_LRCKO
J7701 SCKI 6 43 AUDIO-CLK-OUT
MIC 2 ARAGON-MCK
GUITAR
D/A CONVERTER
GAIN IC604
MUTING CONTROL LOW-PASS
Q7708 Q7707 FILTER 7 VOUTL
IC603 DATA 2 32 SSI0_DO (PARTY CHAIN)
R-CH 8 VOUTR XTAL 71
X105
13.333MHz
BCK 1 EXTAL 70
LRCK 3
ANALOG AUDIO SELECTOR SCK 16 AUDIO-X2 92
IC602 X103
12.288MHz
AUDIO-X1 91
1 Y0
LINE AMP J601 (3/3)
Y 3 L SERIAL FLASH USB-X2 140
J601 (2/3) IC601 AUDIO/PARTY CHAIN X104
L 5 Y1 IC105
AUDIO/PARTY CHAIN OUT 48MHz
R-CH R USB-X1 139
IN (TV) A
R R-CH DI (IO0) 5 170 Q-Flash-SIO0
10
MUTING DO (IO1) 2 172 Q-Flash-SIO1
Q602 IO2 3 166 Q-Flash-SIO2
AUDIO LINK Q612
IO3 7 167 Q-Flash-SIO3 SIGNAL PATH
DETECT MUTING AUDIO LINK CLK 6 168 Q-Flash-CLK
Q605, 607 CONTROL SET CS 1 169 Q-Flash-CS
: AUDIO
Q606 Q603
: TUNER
: DISC PLAY
120 52 114 47 48 175
: AUDIO/PARTY CHAIN IN
MODE-SEL
LINK-DET
LINK-SET
MIC_DET2
MIC-DET1
/LIME-MUTE
: BLUETOOTH
: MIC
MHC-V41D
44 44
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
6-3. BLOCK DIAGRAM - AMP/PANEL Section -

STREAM PROCESSOR DIGITAL POWER AMP AUDIO DSP, SYSTEM CONTROLLER
DOUT1, DOUT2, ARAGON-BCK3, IC2001 IC2002 IC109 (3/4)
ARAGON-LRCK3, ARAGON-MCK REMOTE CONTROL
DOUT1 SP1
>002B 24 SDIN1 PWM_P_2 41 14 INPUT_C OUT_C 32
(MIDRANGE)
SIRCS 135 RECEIVER
DOUT2 IC7450
(Page 44) 25 SDIN2 (L-CH)
ARAGON-BCK3 SP2
23 SCLK (TWEETER) ND7000
ARAGON-LRCK3 (L-CH) VACUUM FLUORESCENT
22 LRCLK DISPLAY
ARAGON-MCK
11 MCLK
PWM_P_1 39 15 INPUT_D OUT_D 27 SP3
(MIDRANGE) FL-SOUT 4 DIN
(R-CH) FL-CLK 2 CLK
OUT_D 28
SP4 FL_LATCH 176 STB
(TWEETER)
(R-CH)
S7000
PWM_P_4 49 5 INPUT_A OUT_A 39 SP5
POWER-KEY 6 1
(SUBWOOFER)
OUT_A 40
S7001 – 7003, 7005, 7007, 7009
PWM_M_4 48 6 INPUT_B OUT_B 35 S7011, 7013, 7015, 7017, 7019,
AD-KEY0 84
S7022, 7024, 7026, 7028
(TOP PANEL KEYS)
RESET
FAULT
4 16 S7004, 7006, 7008, 7010, 7012,
S7014, 7015, 7018, 7020, 7021,
AD-KEY1 85
S7023, 7025, 7027, 7029
VALID 37 (TOP PANEL KEYS)
FAN MOTOR
RESET
MUTE
DRIVE
SDA
SCL
Q2000 NFC BOARD

D2001
20 21 19 16
FAN MOTOR TOUCH-NFC_SDA 130 DATA
FAN MOTOR D2000, 2002
CONTROL M1 TOUCH-NFC_SCL 129 SCL
Q2005 DRIVE M (FAN) NFC-INT 110 IRQ
Q2006
NFC-RF-DET 137 RF-DET
FAN LOCK
PROTECT
Q2002 LED DRIVER
IC7000
D7000
RGB-SOUT 117 2 SIN OUT14 19
MEGA BASS
RGB-SCLK 134 3 SCK
RGB-PWM-CLK 136 21 PWMCLK
RGB-TRANS-PNL-LED/SPK-LED 115 4 TRANS
TOP PANEL GESTURE GESTURE CONTROLLER
CONTROL SENSOR IC7500 D7001
OUT13 18
GUITAR
15 TXD EIO4/SI0 9
EAST
21 RX0 EIO5/S11 10
ELECTRODE
EIO0 1 111 3D-DETECT
D7002
MCLR 13 103 3D-RESET
SOUTH OUT12 17 GESTURE
23 RX2
ELECTRODE ON/OFF
WEST
24 RX3
ELECTRODE D7003
OUT11 16 PAIRING
TH571 NORTH BLUETOOTH
25 RX4
ELECTRODE
PARTY LED BOARD

128 127 57 53 49 80 78 OUT4 9
OUT5 10 GREEN_HILED
SIGNAL PATH
3D (GESTURE)-PWM-SDA
3D (GESTURE)-PWM-SCL
/AMP-RESET
/SD-FAST
AMP-PROTECT
SPM-AMBIENT-TEMP
DAMP-MUTE
OUT6 11 BLUE_HILED
: AUDIO OUT7 12
SW LED BOARD
OUT10 15 SW-LED-GREEN
OUT9 14 SW-LED-BLUE
SW-LED-RED
MHC-V41D
45 45
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
6-4. BLOCK DIAGRAM - POWER SUPPLY Section -

AUDIO DSP, SYSTEM CONTROLLER
IC109 (4/4) +3.3V REGULATOR
TUNER+3.3V
IC903
ST-CE 44
B+ SWITCH
DVDD5V
Q006, 007
+3.3V REGULATOR
SERVO+3.3V
IC305
+5V REGULATOR
AVDD+5V
IC006
+5V REGULATOR
HDMI+5V
IC1000
MTK-POWER-CTRL 59
+12V REGULATOR
SW_12V
IC2000
+9V REGULATOR +12V REGULATOR B+ SWITCH

A+9V
IC004 IC008 Q004, 461
+12 REGULATOR
FAN+12V
IC2003
+12V REGULATOR B+ SWITCH
SW+12V
IC002 Q011, 012
PCONT-PSAVE-PROTECT 60
B+ SWITCH B+ SWITCH
FL+5.2V
Q7001, 7002 IC003
M+5.2V_PNL DC/DC CONVERTER

B+ SWITCH IC001
M+5.2V
IC010
B+ SWITCH
FE_5.2V 14 SW2 VIN2 16
Q457 (1/2), 459
3 SW1 VIN1 1
PG1
PG2
EN1
EN2
USB+5V
5 12 6 11
VBUS SWITCH
VBUS
IC452
VBUS-OE 112
USB-OC 35
PROTECTOR 82
E+1.2V
DC/DC CONVERTER
B+ SWITCH IC009
DVDD3.3V
Q005, 457 (2/2)
B+ SWITCH
AVDD3.3V 3 SW1 VIN1 1
Q302, 303
14 SW2 VIN2 16
PG1
PG2
B+ SWITCH
E+3.3V
IC007 6 11
+1.2 REGULATOR
SERVO+1.2V
IC303
POWER CONTROL
B+ SWITCH IC6300
SERIAL FLASH B+
Q304, 305
D6516 D6511 D6306
LATCH SWITCH ISOLATOR LATCH SWITCH
LATCH-ON 27 1 LATCH
Q6506, 6507 PH6302 Q6305
B+ SWITCH
+3.3V
Q110, 111 SHUNT
ISOLATOR
REGULATOR 3 FB
PH6301
B+ SWITCH IC6500
BT3.3V T6300
Q103, 104
POWER
BT-ON 16 TRANSFORMER
B+ SWITCH D6312
D+3.3V RECT REGULATOR
Q008, 009 POWER AMP B+ 6
D6604 Q6304
VCC
PCONT-BTSTBY 122
POWER POWER
B+ SWITCH B+ SWITCH
SPM-C-MON 79 CONTROL CONTROL
Q574 – 576 Q571, 572 F6500
Q6501 Q6504 RECT POWER
C-CONT 55 D6501 RECT SWITCH 5 DRV
PCONT-DAMP 118 D6000 Q6300 – 6303
RESET SIGNAL 1 HV
RES 76 GENERATOR
IC103
TH6000 F6000
BUS BUFFER AC DETECT ISOLATOR AC DETECT RECT LINE FILTER LINE FILTER CN6001
AC-CUT 63
IC102 (2/2) Q6500 PH6300 Q6307 D6001 LF6000 LF6001 - AC IN
(Page 44)
RESET
>003B
MHC-V41D
46 46
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.) • Circuit Boards Location GESTURE board
For Printed Wiring Boards. For Schematic Diagrams. PANEL board PARTY LED board
Note: Note:
• X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
• Y : Parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics
MIC board
• : Pattern from the side which enables seeing. and tantalums.
(The other layers’ patterns are not indicated.) • All resistors are in Ω and 1/4 W or less unless otherwise
specified. SMPS board
Caution: • 2 : Nonflammable resistor.
Pattern face side: Parts on the pattern face side seen • C : Panel designation.
(SIDE B) from the pattern face are indicated. NFC board
Note: The components identified by mark 0 or dotted
Parts face side: Parts on the parts face side seen from
line with mark 0 are critical for safety.
(SIDE A) the parts face are indicated. MS-476 board
Replace only with part number specified.
• MOTHER board is multi-layer printed board. However, • A : B+ Line.
the patterns of intermediate layers have not been includ- • Voltages are dc with respect to ground under no-signal
ed in diagrams. MOTHER board
(detuned) conditions.
• Indication of transistor. no mark : TUNER (FM)
* : Impossible to measure IR board
C • Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
Q These are omitted.
tolerances.
B E • Signal path.
d : USB
N : MIC
Q
Note 1: Among mounted electrical parts on each board, only
parts that are described in the electrical parts list can
B C E be replaced for repairing.
These are omitted. The parts that are not described in the electrical parts
list cannot be replaced with single for repairing.
Note 1: Among mounted electrical parts on each board, only
parts that are described in the electrical parts list can Note 2: Among mounted parts on the MOTHER board, only
be replaced for repairing. parts that are described in the electrical parts list can
The parts that are not described in the electrical parts be replaced for repairing.
list cannot be replaced with single for repairing. When the parts that are not described in the electrical
parts list are defective, replace the complete mounted
SW-LED board
Note 2: Among mounted parts on the MOTHER board, only board.
parts that are described in the electrical parts list can In this service manual, the block diagram and printed
be replaced for repairing. wiring board of the MOTHER board are described
When the parts that are not described in the electrical for reference.
parts list are defective, replace the complete mounted Also, when the MOTHER board is replaced, be sure
board. to refer to “DESTINATION SETTING METHOD”
In this service manual, the block diagram and printed and “NFC OPERATION CHECKING METHOD”
wiring board of the MOTHER board are described on page 6.
for reference.
Also, when the MOTHER board is replaced, be sure Note 3: When the PARTY LED, SW LED, NFC and MS-476
to refer to “DESTINATION SETTING METHOD” boards are defective, replace the complete mounted
and “NFC OPERATION CHECKING METHOD” board or the whole parts including the applicable
on page 6. board.
The mounted parts cannot be replaced with single for
Note 3: When the PARTY LED, SW LED, NFC and MS-476 repairing.
boards are defective, replace the complete mounted In this service manual, the schematic diagram and
board or the whole parts including the applicable printed wiring board of the PARTY LED, SW LED,
board. NFC and MS-476 boards are not described.
The mounted parts cannot be replaced with single for Also, when the NFC board is replaced, be sure to re-
repairing. fer to “NFC OPERATION CHECKING METHOD”
In this service manual, the schematic diagram and on page 6.
printed wiring board of the PARTY LED, SW LED,
NFC and MS-476 boards are not described. Note 4: When the SMPS board is defective, replace the com-
Also, when the NFC board is replaced, be sure to re- plete mounted board.
fer to “NFC OPERATION CHECKING METHOD” The mounted parts cannot be replaced with single for
on page 6. repairing.
However, in this service manual, the block diagram,
Note 4: When the SMPS board is defective, replace the com- schematic diagram and printed wiring board of the
plete mounted board. SMPS board are described for reference.
The mounted parts cannot be replaced with single for
repairing.
However, in this service manual, the block diagram,
schematic diagram and printed wiring board of the
SMPS board are described for reference.
Note 5: The MOTHER board has been changed in the mid-

way of production.
Refer to “CHANGE OF MOTHER BOARD” on
page 8 for details.
MHC-V41D
47 47
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-5. PRINTED WIRING BOARD - MOTHER Board (Side A) (Former MB type) - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12
M1
(FAN)
M
A >06P SMPS BOARD

NO6501
(Page 58)
MOTHER BOARD (SIDE A)
D2002
Q2000 C2018 R2040 3
C2017 C2079 C2084
Q2006
A CN2001
E
D2000
R2015
E R2039
R2036
1
C2004
IC2000 C2063
R2085 R2037 2 1 2
K R2035
R2087 A C2115 C2022 C2068
CN001 1 6 R2014 R2013 C2012
JL057 1 10 E
C2014
R2020
6
R2051
R2019
C2013
3 4 R2084 C2024
C2054
C2051
C048 Q2002
C2025
C2098
Q2005
B
C2058
R2025
A C2038
L006 R2078
K/A C2067
D2001
C2023 R2026 C2009 R2042
C010 C092 R086 K C2006 C2007 C2097
L009 C037 R2046
C011 C091 C2003 1 56 R2152 1 44
C2016 R2049
C039 C2020 C2042
R001
E R2024 R2076 C2008 C2032
C2026
IC2002
R023 Q575 R2142
L008 C053 R025 R024 C055 R2023 R2003 C2045
C2021
R2006 R2143
C093 C024
C026 16 9 C030
R483
R491
R2007 C2108
R2008 R2004 IC2001 C2028 C2027
C052
JL2042
IC001 C577
JL2041 R2118 C2046
Q574
L003 C574 Q576 G D R2136 R2093
1 8 R2137
E S C2010 R2116
C017 E R2009 C2043 R2053 C2060
C013
Q571 C573 R485 R2096
C R2031 22 23
R013
R087 R487 R2011 28 29
R012
L002 C015 C054 R572 K A
C105
D102 C104
R099 R2034 R2088 C2036 C2039 C2100
C004 D572 K A
Q572
C016 R2150 R2010
C2099
C096 K A
R014 C003 R571 E
C2055
C2052
C006 3 2 C103 C2015
L004 R051
IC103 4 R2101 C2071
C014
C019 16 D571 E R128 Q107 R117 R2151

9 C050 L001 C005 1 R2052
C107 R115 R2044
C040 R2077
R113 R577 C2069 C2095 C2090
C150 C110 R116 C2135
R088
IC009
C049
R127
C109
C028 C106
C2150
R114 C127
1 8 C038
C162
R159
R158
R026 C2059
R032 C041
C149 C126
R511
R172
C047
R160 X105
R521
C116
R173
R168
C029
C057 FB101 1
C084 (See Note 2) RB109 RB108
D L007 C161
C128
C129
C130 X103 R190
R186
R151 R169
R247
R519
R164
R323 JL331
L1001
C337
R365
R367
1 R188 R181
C085 E R061 C366 1 R434 R349 (TV)
Q009 2 2 L1002
R299 R150 R424 R351 JL332 R368
Q008
C083 E R196 E R378 X301 CN1000 ARC

88 45 R450
R193 C341
Q401
89 44 R322 R989 C322 R1010 HDMI OUT
R062 C132 R301 C421 R334 128 R1014
C072 R201 R988 97
C068
R108
R109 E R200
R205 D103
CN302
C302
C420
IC305
2 1 R987
C958 C323
R332 1 96
CL328
R1015
R1011 19
CN113 C303 R421
R1000
E Q104 R198 R517 K A JL363 R422 CL329 R1019
FFC3 C167 R295 C356 C1006
Q103 (NC) R520 3 4
R371
C353
R211 E C073 R1020
RB107
R213 R1012
>03P Q006 C307
GESTURE
JL053 R077
R509 R218
24
23
C071 R470 IC301
BOARD
15
R223 IC109 R219 R221 R040
C468
R472
C308
R331
RB303
E CN7500 R225
16 R227 C141 C139 R048 1 8
(Page 54) R228 R224 10 8 R335 R327 RB305
Q007
R039 R340
R233
R236 R166
C142
C143
R226
R229 5 1 E
1
2
7
6
R329 IC302 R342
R238
>02P R241 CN303 35 4 5 32
33 64
65 RB302
IR
1
R547
R548
R232
R171
4 2
IC453 C324
R356
R354
R355 RB307
BOARD R549 R344 RB308 RB301
2 R550 R535 C467
CN7451 R345 R380
R121 R242
(Page 53) FB601
R716 R130 132 1 R251
RB309
R369
R379 RB304 R692 C629 R756
FB602 R132 133 176 R257 RB306 C656
6 R192 Q607 C659
CN127
R700
R531
FB603 R998 R189 5 1 1 6

7 R285 R291 R261 C658
C626
R275
R288
R289
MIC BOARD R208 R270 3 4

CN7701 >01P CN601
1 3 R510 R271
54 28
R280
C297 CN451 C917

R267
C151
R278
C152
(Page 53) 2 6 C298 R752

F
R624
CN120
R264
R292
R290
FFC6 E
Q606
1 7 X104
R540 E
E R653
FB321
NFC
C627
JL296 JL295 1
R625
Q110
BOARD R781
IC306 6
CL3046 CL3047
Q111
Q602
R782 FL301
R3018
9 8
FL601
R3030
R3016
3 1
FFC5 C628
R753
4 3
IC905
CL3043
CL3042
CL3041
CL3054
CL3050
CL3049
CL3048
CL3056
CL3052
CL3051
CL3040
CL3045
CL3055
6 2 C654 R779 Q603

CN105 R923
CL3057
5 1 16 1 4 6
FB320
R650
R167 R784 1 27 R641
43 27
C362
R101
CL3030 FB104
26 R3019 FB102 C664
R619
R618
R820 R126
CL3029 C608
C602
C766 R644
C604
C067 C632 6
CL3024 R630 R617 C610 R605 R604 R602 R915 R124
C601
CL3022 R631
C630
R607
G CP3000 C3004 16 9 R642
C603
R620 R614
C620
19 1 R632 R609 R613 R610 C607 CN108
BLUETOOTH MODULE R3035 CL3023 R626 4 1
CN103 1 R608
CL3028
18 2
3 1
IC604 C613
4 1 8
(NC)
R616
CL3027 R750
R615
C614
R030 C943
Q457
IC601
C605
C618
CL3026 R628
R622
IC603 IC602
C938
18 4 6 D401 1 8 C624
CL3020 FB103 FB105 A K C606 4 3
R162 C616 5 8 IC9031 C941
R141
R165 A K C615
CL3036
CL3037
CL3038
CL3039
CL3012
CL3013
CL3035
CL3016
CL3031
CL3032
CL3019
CL3014
CL3015
CL3033
1 17 R163 C619 5 8 9 16 2 1
D402 R415 R649 R916
R652
R648
CL3011
CN402 R635 R646 R634 R627

R446
C621
C3006 4 C411 R638 FB610
R3021 R3022
C418
R600
R3020 R656
CL3034
C3005 C767
C612
R751
IC3000
R655
C635
C633
R640
R3027 R002 4 1 R647 C631
R3028 R447 C625
R654
C634
R3025 5 4 JL055 R448
VR3001 R3029
C419
C3001 8 CN104 C076

1 1
CL3062 R449 R404 R401 C403
R027 R408
R3033 R410 R409 R402 C402
H 2 1
JL056
CN3001 11
C3503
1-983-576- (11)
FFC4 FFC1 FFC2
>04P SW LED OP1 MS-476 >05P
BOARD OPTICAL PICK-UP BLOCK BOARD
PANEL BOARD PANEL BOARD
(CMS-S76RFS7G1/S76RFS7GP)
CN7007 CN7800
MIC1
(Page 56) (Page 56)
Note 3: The MOTHER board has been changed in the midway of production.
The MOTHER board before changing (Former MB type) is described on this page.
Note 1: When the IC2002 on the MOTHER board is replaced, Note 2: The CN113 on the MOTHER board has Refer to page 50 for the MOTHER board after changing (New MB type).
refer to “SPREADING OF COMPOUND” on page 7. been deleted in the midway of production. Also, refer to “CHANGE OF MOTHER BOARD” on page 8 for details.
MHC-V41D
48 48
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-6. PRINTED WIRING BOARD - MOTHER Board (Side B) (Former MB type) - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
A >07P SMPS BOARD

CN6500
(Page 58)
MOTHER BOARD (SIDE B)
CN2007
1 3 9 JL2006 C2128
C2116 CL2010 CL2038
R2147
2 CL2004
CL2039
JL2030 JL2033
CL2042
JL2021
CL2040
IC2003 3 CL2011 JL068
CL2049 JL2018 JL2003 CL2024 1 JL2031
CL2041
CL2046
CL2047
CL2045
CL2044
SP5 6 C062 R031
(SUBWOOFER) JL045
B L2002 JL2011 R2146
C2127 JL001 R053
JL004
R046
R045
R068
SP4 CL2048 R019
CL2043 CL2026
(TWEETER) C2076
(R-CH) JL2012
R050 4 3 IC010 E
R064
R020
Q461
R049 R035
R2022
1 C060
Q011
R069
R2021
C2019
R2068
R2069
6 R066 E
SP3 R060
CN2021 C061 R007 E JL005
R033
Q012
(MIDRANGE) R047 JL059
CL2050 CL2023
(R-CH) R065 C078
JL2008 R2067 R029
JL2020 JL2036 JL2037
JL2034 C051
SP2 CL2025
(TWEETER) JL008 JL046
CL2052 R2066 JL2040 JL2039
(L-CH) R006 JL012 E 1
CL2021
JL2015 JL071
CL2022 Q004
C SP1
JL2016
CL2020 JL269 JL150
R008 3 IC008
(MIDRANGE)
(L-CH)
1 CL2051
JL2038 CL2035
IC0074 3 R044
2
JL2009 R2070 CL2036 JL069 C031
R018 6 1
R098
L2003 C080
C2131 JL044 R009
JL2029 8 7 C032 R004
C2132 JL073 C079
R129 R131 R017
C2151
R120
IC102 R123
1
R015
JL2005
R528
C102 14
RB105
1
JL148 JL176
JL175
R005 JL047 3 IC004
R529 R143 R249 JL174 2
JL072
JL2026 JL2035 CL415 E R139 JL289 JL173
L601 IC1000 C424 R170 R107 R137TH571 R144 1
R1017
JL110 C638 Q402 R429 R176

R102 R104
C1003
R522
R191
D CL309 CL310
R318
R310
R145 JL049
R184
JL111
JL905
C636 3 1 Q303 JL330 R316 R255 R533 R140
R524
C118
R149
JL172
JL196 3 IC006
R358
JL361 JL171
R222
R435 C367 R177
E R360 JL313 CL414 C2000
C1005
C350 JL303 JL302 C123 2

R1024 C1004
C112 C114 R175 JL198

CL307 JL304 JL306 JL197
IC1001 C111
R103
4 1 CL315 R637 C280
R412
4 5 R319 CL316 C950 R959 R957 C423 R300 C115 C281 JL011
JL631 R370 JL309 R513 JL199 JL200 JL048
C328
R1025 R328 C331 C316 C960 JL312 C503 C131
JL1003 CL395 JL308 R512 C117 JL195
C282
C120
C122
C306 36 25 CL413 R431 C504 JL201
CL311 CL313
C1013
R1026
5 8 R432 JL310 C133 C134

C1009 C330 R326 R389
C1011 C352 C338 JL301 JL216
C1010 Q302 37 24 JL215
JL307 JL315 JL316 RB101
C343
X602
R321
C340
C339
E C347 JL314 C135 JL113

R1022
R1023
C334 C951 JL305 JL318 JL202 JL114

C319 C949 JL311 JL319 R273
R1027 CL380
IC904 JL317 JL169
R953
R359 C375 R330 C952 R215 C136
R518
C299
C963 JL203 JL217
R174
RF
C351 C325 JL321
JL320 JL324 R220
R955
R309 R339 JL356 48 13 JL235
VIDEO R451 C465 C137 R152 JL204
C346 C326 C954 R453 R498
OUT JL357 R664 JL322 JL325 C138 JL205
E C348
JL359 R657 R658C981 1 12 4 3
JL326 C140 R532 JL109
JL206
IC452 6 R274
C462
R984
R985
R986
C344 C342 C985 JL328 JL327 R514 R237 C502 R298
C144
R981
R982
JL619 R348 1 R792
R195
R284
R546
R230 R534
C463
L C466 C311 R515 R256 JL613
C147
JL358 R665 R148 C501 R722 R723 R720
CL308 C336 R660 C671
RB310 C663 E C146 JL116 JL227
JL620 FB455 JL115 R545
OUT R352 R983
C662 JL463 Q1002 JL294 C148 C168 R544 8 7 JL615 JL614
JL355 JL362 JL360 JL117
R
C321
C372 JL462
C153 C283 R134 R719
R106 IC609 C678
C369
C315 JL209 R119 C160 R543 JL910

E JL119 JL118 C675 C669
Q304
L301 C674
FB109
JL461 C157 JL120 C986
J601 R302 1 6 R1007 C155 C158 C159 R283 R135 14 1 JL616
JL635 R950 JL212 R711
C181 3 4 R293 JL121 JL134 C673
R478 JL525 R709 JL908
R303
IC303 R276
C670
AUDIO/PARTY CHAIN Q1000 C154 C156 C672
R952 Q305 JL122 R122 JL909
C373
R686 JL460 E JL528 JL529 C667 R917
R708
C666
E R1001 C1001 R254 JL155 JL135
R651 R381 C358 C357 R951 RB104 JL601
C665
F L 6 4 JL604 JL323 JL329 K

D1001
A
RB106
JL527 JL154
JL132
JL131 JL617
JL125
Q605 R1005
IN (TV) 1 3 R778 R783 R1006
Q1005
C660
R689 C164 JL526 JL152

JL605 E 8 5 JL530
R
R382
R685 C364 C360
C365 Q1001
JL524
IC106 JL151 JL153
C363 R690 R687
JL618 C359 E
R691 R688 JL144 1 4 JL194
R1004
C653
8 7 R1003
JL101 C655 C1000 JL521 JL297
JL102
C180
C695 R785 IC606 R1002
FB106
JL138
JL147 JL287 JL107
JL106
X900 R677 C987 E R037 R3009
R1008 14 1 JL143 R187 JL231 JL523
C649
Q005
R911 FB108
G
C644 C646 JL140 R185 CL3003
CN900 C657 R913 R663 C648 R674
C645 R411 JL024
C647 R661 C642 CL412 FB107 JL142 JL145
1
R937
FM C934 R662 C641 C711 R034 JL139 JL124 JL105

L605
IC902 R857 JL230 R240 JL522
C609
ANTENNA JL901 R671 C640 C407 C413 R313 CL411 R003 R3015
C065
L900
2 20 16 R669 R314 JL136

C933 C650 C409 R183 R3004
1 15 R945 R418 C408 JL146 JL137 JL123
C931
R914 C643
R3039 R3003
C652 CL408 CL410 C008 JL232 R3014
JL900 K/A C930 R946 CL409 C405 JL023 JL021
C622
R912 R794 CL3002

5 11 R947 C726 JL022 R3005
D900 L901C932 JL108
6 10 R943
C617
28 22
30
21 15
C406
JL149
4 1
JL002
JL141JL520
IC3001 R3044
A K L902 JL401 1 4
R639 E C3019
Q612
C936 JL130 2 3 R3040 R3041

R940 R939 JL402 IC002 C087
IC401
C012
R944 JL603 C3018 CL3059 R3043
JL405 5 8 R3042
JL2200 R3032
CL3058 CL3001 CL3000
JL2222 JL2203 JL406 JL070 CL3007
H JL2221 JL2206 JL2207
1 7 8 14 C064 C3000 R3045
R3048 CL3005
CL3006
29 R096
R3049
C097 CL3004
JL2223 C404 R091 R094 R3046
JL2224 CL401 CL403 CL405 Q459
JL050 C066 1 6 CL3063 CL3064
C095
R095
E CL3008
CL402 3 4 CL3009
11
R028 R097 R3047
IC003
R406
R407
CL404 1-983-576- (11)
Note: The MOTHER board has been changed in the midway of production.
The MOTHER board before changing (Former MB type) is described on this page.
Refer to page 51 for the MOTHER board after changing (New MB type).
Also, refer to “CHANGE OF MOTHER BOARD” on page 8 for details.
MHC-V41D
49 49
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-7. PRINTED WIRING BOARD - MOTHER Board (Side A) (New MB type) - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12
M1
(FAN)
M
A >16P SMPS BOARD

NO6501
(Page 58)
MOTHER BOARD (SIDE A)
D2002
Q2000 C2018 R2040 3
C2017 C2079 C2084
Q2006
A CN2001
E
D2000
R2015
E R2039
R2036
1
C2004
IC2000 C2063
R2085 R2037 2 1 2
K R2035
R2087 A C2115 C2022 C2068
CN001 1 6 R2014 R2013 C2012
JL057 1 10 E
C2014
R2020
6
R2051
R2019
C2013
3 4 R2084 C2024
C2054
C2051
C048 Q2002
C2025
C2098
Q2005
B
C2058
R2025
A C2038
L006 R2153
K/A C2067
D2001
C2023 R2026 C2009 R2042
C010 C092 R086 K C2006 C2007 C2097
L009 C037 R2046
C011 C091 C2003 1 56 R2152 1 44
C2016 R2049
C039 C2020 C2042
R001
E R2024 R2076 C2008 C2032
C2026
IC2002
R023 Q575 R2142
L008 C053 R025 R024 C055 R2023 R2003 C2045
C2021
R2006 R2143
C093 C024
C026 16 9 C030
R483
R491
R2007 C2108
R2008 R2004 IC2001 C2028 C2027
C052
IC001 C577
R2118 C2046
Q574
L003 C574 Q576 G D JL2041 R2093
1 8 JL2042
E S C2010
C017 E R2009 C2043 R2053 C2060
C013
Q571 C573 R485 R2096
C R2031 22 23
R013
R087 R487 R2011 28 29
R012
L002 C015 C054 R572 K A
C105
D102 C104
R099 R2034 C2036 C2039 C2100
C004 D572 K A
Q572
C016 R2010
C2099
C096 K A
R014 C003 R571 E
C2055
C2052
C006 3 2 C103 C2015
L004 R051
IC103 4 C2071
C014
C019 16 D571 E R128 Q107 R117

9 C050 L001 C005 1 R2052
C107 R115 R2044
C040
R113 R577 C2069 C2095 C2090
C150 C110 R116 C2135
R088
IC009
C049
R127
C109
C028 C106
C2150
R114 C127
1 8 C038
C162
R159
R158
R026 C2059
R032 C041
C149 C126
R511
R172
C047
R160 X105
R521
C116
R173
R168
C029
C057 FB101 1
C084 RB109 RB108
D L007 C161
C128
C129
C130 X103 R190
R186
R151 R169
R247
R519
R164
R323 JL331
L1001
C337
R365
R367
R188 R181
C085 E R061 C366 1 R434 R349 (TV)
Q009 2 L1002
R299 R150 R424 R351 JL332 R368
Q008
C083 E R196 E R378 X301 CN1000 ARC

88 45 R450
R193 C341
Q401
89 44 R322 R989 C322 R1010 HDMI OUT
R062 C132 R301 C421 R334 128 R1014
C072 R201 R988 97
C068
R108
R109 E R200
R205 D103
CN302
C302
C420
IC305
2 1 R987
C958 C323
R332 1 96
CL328
R1015
R1011 19
C303 R421
R1000
E Q104 R198 R517 K A JL363 R422 CL329 R1019
FFC3 C167 R295 C356 C1006
Q103 R520 3 4
R371
C353
R211 E C073 R1020
RB107
R213 R1012
>13P Q006 C307
GESTURE
JL053 R077
R509 R218
24
23
C071 R470 IC301
BOARD R223 IC109 R219 R221 R040
C468
R472
C308
R331
RB303
E CN7500 R225
R227 C141 C139 FB013 1 8
(Page 54) R228 R224 10 8 R335 R327 RB305
Q007
R039 R340
R233
R236 R166
C142
C143
R226
R229 5 1 E
1
2
7
6
R329 IC302 R342
R238
>12P R241 CN303 35 4 5 32
33 64
65 RB302
IR
1
R547
R548
R232
R171
4 2
IC453 C324
R356
R354
R355 RB307
BOARD R549 R344 RB308 RB301
2 R550 R535 C467
CN7451 R345 R380
R121 R242
(Page 53) FB601
R716 R130 132 1 R251
RB309
R369
R379 RB304 R692 C629 R756
FB602 R132 133 176 R257 RB306 C656
6 R192 Q607 C659
CN127
R700
R531
FB603 R998 R189 5 1 1 6

7 R285 R291 R261 C658
C626
R275
R288
R289
MIC BOARD R208 R270 3 4

CN7701 >11P CN601
1 3 R510 R271
54 28
R280
C297 CN451 C917

R267
C151
R278
C152
(Page 53) 2 6
C298 R752
F
R624
CN120
R264
R292
R290
FFC6 E
Q606
1 7 X104
R540 E
E R653
FB321
NFC
C627
JL296 JL295 1
R625
Q110
BOARD R781
IC306 6
CL3046 CL3047
Q111
Q602
R782 FL301
R3018
9 8
FL601
R3030
R3016
3 1
FFC5 C628
R753
4 3
IC905
CL3043
CL3042
CL3041
CL3054
CL3050
CL3049
CL3048
CL3056
CL3052
CL3051
CL3040
CL3045
CL3055
6 2 C654 R779 Q603

CN105 R923
CL3057
5 1 16 1 4 6
FB320
R650
R167 R784 1 27 R641
43 27
C362
R101
CL3030 FB104
26 R3019 FB102 C664
R619
R618
R820 R126
CL3029 C608
C602
C766 R644
C604
C067 C632 6
CL3024 R630 R617 C610 R605 R604 R602 R915 R124
C601
CL3022 R631
C630
R607
G CP3000 C3004 16 9 R642
C603
R620 R614
C620
CL3023 19 1 R632 R609 R613 R610 C607 CN108
BLUETOOTH MODULE R626 4 1
CN103 1 R608
CL3028
18 2
3 1
IC604 C613
4 1 8
(NC)
R616
CL3027 R750
R615
C614
R030 C943
Q457
IC601
C605
C618
CL3026 R628
R622
IC603 IC602
C938
18 4 6 D401 1 8 C624
CL3020 FB103 FB105 A K C606 4 3
R162 C616 5 8 IC9031 C941
R141
R165 A K C615
CL3036
CL3037
CL3038
CL3039
CL3012
CL3013
CL3035
CL3016
CL3031
CL3032
CL3019
CL3014
CL3015
CL3033
1 17 R163 C619 5 8 9 16 2 1
D402 R415 R649 R916
R652
R648
CL3011
CN402 R635 R646 R634 R627

R446
C621
C3006 4 C411 R638 FB610
R3029 R3021 R3022
C418
R600
R656
CL3034
C3005 C767
C612
R751
IC3000
R655
C635
C633
R640
R3020 4 1 R647
R447 C625 C631
R3028
R654
C634
5 4 JL055 R448
VR3001
C419
C3001 8 CN104 C076

1 1
CL3062 R449 R404 R401 C403
R027 R408
R410 R409 R402 C402
H 2 1
JL056
CN3001 21
C3503
1-983-189- (21)
FFC4 FFC1 FFC2
>14P SW LED OP1 MS-476 >15P
BOARD OPTICAL PICK-UP BLOCK BOARD
PANEL BOARD PANEL BOARD
(CMS-S76RFS7G1/S76RFS7GP)
CN7007 CN7800
MIC1
(Page 56) (Page 56)
Note 2: The MOTHER board has been changed in the midway of production.
The MOTHER board after changing (New MB type) is described on this page.
Note 1: When the IC2002 on the MOTHER board is replaced, Refer to page 48 for the MOTHER board before changing (Former MB type).
refer to “SPREADING OF COMPOUND” on page 7. Also, refer to “CHANGE OF MOTHER BOARD” on page 8 for details.
MHC-V41D
50 50
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-8. PRINTED WIRING BOARD - MOTHER Board (Side B) (New MB type) - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
A >17P SMPS BOARD

CN6500
(Page 58)
MOTHER BOARD (SIDE B)
CN2007
1 3 9 JL2006 C2128
C2116 CL2010 CL2038
R2147
2 CL2004
CL2039
JL2030 JL2033
CL2042
JL2021
CL2040
IC2003 3 CL2011 JL068
CL2049 JL2018 JL2003 CL2024 1 JL2031
CL2041
CL2046
CL2047
CL2045
CL2044
SP5 6 C062 R031
(SUBWOOFER) JL045
B L2002 JL2011 R2146
C2127 JL001 R053
JL004
R046
R045
CL2048
R068
SP4 R019
CL2043 CL2026
(TWEETER) C2076
(R-CH) JL2012
R050 4 3 IC010 E
R064
R020
Q461
R049 R035
1 C060
Q011
6 R066 R069
E
SP3 R2022 R060
C2019 C061 JL005
CN2021 E R033
Q012
(MIDRANGE) JL059
(R-CH) R2021 CL2023 R065
JL2008 C078
JL2036 JL2037 R029
JL2020
CL2050 JL2034 C051
SP2 CL2025
(TWEETER) JL008 JL046
CL2052 JL2040 JL2039
(L-CH) JL012 E 1
CL2021
JL2015 JL071
CL2022 Q004
C SP1 CL2051
JL2016
CL2020 JL269 JL150
3 IC008
(MIDRANGE)
(L-CH)
1
JL2038 CL2035
IC0074 3
2
JL2009 CL2036 JL069 C031
R018 6 1
L2003 C080
C2131 JL044
JL2029 8 7 C032 C079
C2132 R131 JL073
R129
C2151
R120
IC102 R123
1
R015
JL2005
R528
C102 14
RB105
1
JL148 JL176
JL175
JL047 3 IC004
R529 R143 R249 JL174 2
JL072
JL2026 JL2035 CL415 E R139 JL289 JL173
L601 IC1000 C424 R170 R107 R137TH571 R144 1
R1017
JL110 C638 Q402 R429 R176

R102 R104
C1003
R522
R191
D CL309 CL310
R318
R310
R145 JL049
R184
JL111
JL905
C636 3 1 Q303 JL330 R316 R255 R533 R140
R524
C118
R149
JL172
JL196 3 IC006
R358
JL361 JL171
R222
R435 C367 R177
E R360 JL313 CL414 C2000
C1005
C350 JL303 JL302 C123 2

R1024 C1004
C112 C114 R175 JL198

CL307 JL304 JL306 JL197
IC1001 C111
R103
4 1 CL315 R637 C280
R412
4 5 R319 CL316 C950 R959 R957 C423 R300 C115 C281 JL011
JL631 R370 JL309 R513 JL199 JL200 JL048
C328
R1025 R328 C331 C316 C960 JL312 C503 C131
JL1003 CL395 JL308 R512 C117 JL195
C282
C120
C122
C306 36 25 CL413 R431 C504 JL201
CL311 CL313
C1013
R1026
5 8 R432 JL310 C133 C134

C1009 C330 R326 R389
C1011 C352 C338 JL301 JL216
C1010 Q302 37 24 JL215
JL307 JL315 JL316 RB101
C343
X602
R321
C340
C339
E C347 JL314 C135 JL113

R1022
R1023
C334 C951 JL305 JL318 JL202 JL114

C319 C949 JL311 JL319 R273
R1027 CL380
IC904 JL317 JL169
R953
R359 C375 R330 C952 R215 C136
R518
C299
C963 JL203 JL217
R174
RF
C351 C325 JL321
JL320 JL324 R220
R955
R309 R339 JL356 48 13 JL235
VIDEO R451 C465 C137 R152 JL204
C346 C326 C954 R453 R498
OUT JL357 R664 JL322 JL325 C138 JL205
E C348
JL359 R657 R658C981 1 12 4 3
JL326 C140 R532 JL109
JL206
IC452 6 R274
C462
R984
R985
R986
C344 C342 C985 JL328 JL327 R514 R237 C502 R298
C144
R981
R982
JL619 R348 1 R792
R195
R284
R546
R230 R534
C463
L C466 C311 R515 R256 JL613
C147
JL358 R665 R148 C501 R722 R723 R720
CL308 C336 R660 C671
RB310 C663 E C146 JL116 JL227
JL620 FB455 JL115 R545
OUT R352 R983
C662 JL463 Q1002 JL294 C148 C168 R544 8 7 JL615 JL614
JL355 JL362 JL360 JL117
R
C321
C372 JL462
C153 C283 R134 R719
FB110 IC609 C678
C369
C315 JL209 R119 C160 R543 JL910

E JL119 JL118 C675 C669
Q304
L301 C674
FB109
JL461 C157 JL120 C986
J601 R302 1 6 R1007 C155 C158 C159 R283 R135 14 1 JL616
JL635 R950 JL212 R711
C181 3 4 R293 JL121 JL134 C673
R478 JL525 R709 JL908
R303
IC303 R276
C670
AUDIO/PARTY CHAIN Q1000 C154 C156 C672
R952 Q305 JL122 R122 JL909
C373
R686 JL460 E JL528 JL529 C667 R917
R708
C666
E R1001 C1001 R254 JL155 JL135
R651 R381 C358 C357 R951 RB104 JL601
C665
F L 6 4 JL604 JL323 JL329 K

D1001
A
RB106
JL527 JL154
JL132
JL131 JL617
JL125
Q605 R1005
IN (TV) 1 3 R778 R783 R1006
Q1005
C660
R689 C164 JL526 JL152

JL605 E 8 5 JL530
R
R382
R685 C364 C360
C365 Q1001
JL524
IC106 JL151 JL153
C363 R690 R687
JL618 C359 E
R691 R688 JL144 1 4 JL194
R1004
C653
8 7 R1003
JL101 C655 C1000 JL521 JL297
JL102
C180
C695 R785 IC606 R1002
FB106
JL138
JL147 JL287 JL107
JL106
X900 R677 C987 E R037 R3009
R1008 14 1 JL143 R187 JL231 JL523
C649
Q005
R911 FB108
G
C644 C646 JL140 R185 CL3003
CN900 C657 R913 R663 C648 R674
C645 R411 JL024
C647 R661 C642 CL412 FB107 JL142 JL145
1
R937
FM C934 R662 C641 C711 R034 JL139 JL124 JL105

L605
IC902 R857 JL230 R240 JL522
C609
ANTENNA JL901 R671 C640 C407 C413 R313 CL411 R3015
C065
L900
2 20 16 R669 R314 JL136

C933 C650 C409 R183 R3004
1 15 R945 R418 C408 JL146 JL137 JL123
C931
R914 C643
R3039 R3003
C652 CL408 CL410 C008 JL232 R3014
JL900 K/A C930 R946 CL409 C405 JL023 JL021
C622
R912 R794 CL3002

5 11 R947 C726 JL022 R3005
D900 L901C932 JL108
6 10 R943
C617
28 22
30
21 15
C406
JL149
4 1
JL002
JL141JL520
IC3001 R3044
A K L902 JL401 1 4
R639 E C3019
Q612
C936 JL130 2 3 R3040 R3041

R940 R939 JL402 IC002 C087
IC401
C012
R944 JL603 C3018 CL3059 R3043
JL405 5 8 R3042
JL2200 R3032
CL3058 CL3001 CL3000
JL2222 JL2203 JL406 JL070 CL3007
H JL2221 JL2206 JL2207
1 7 8 14 C064 C3000 R3045
R3048 CL3005
CL3006
29
R3049
C097 CL3004
JL2223 C404 R091 R3046
JL2224 CL401 CL403 CL405 Q459
JL050 C066 1 6 CL3063 CL3064
E C095 R094 CL3008
CL402 3 4 CL3009
R097 21
R028 R3047
IC003
R406
R407
CL404 1-983-189- (21)
The MOTHER board after changing (New MB type) is described on this page.
Refer to page 49 for the MOTHER board before changing (Former MB type).
Also, refer to “CHANGE OF MOTHER BOARD” on page 8 for details.
MHC-V41D
51 51
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-9. SCHEMATIC DIAGRAM - MIC Board -
1 2 3 4 5 6 7 8 9 10 11 12
MIC BOARD
A C7710
100p
R7722
CL7709 1.2k
CL7708 CL7737
R7716 C7713
22k 22p
C7709 C7724
10 10
50V 50V
CL7713 CL7721
CL7714
CL7719
R7707 C7718
B 10k 1 J7700
CL7724 MIC 1
C7715 C7716 R7725 C7719 C7720 R7729 R7734
0.1 220 10k 220 0.1 100k 10k
16V 16V
CL7711
4.4
4.4
4.4
C7727
0.001
1
2
3
4
VEE
C IC7700 D7704 CL7718
MIC AMP BAV99-215
IC7700
BA4558F-E2
W7700
CL7717
CN7701 (CHASSIS)
VCC
7P R7701
CL7700 0
D7705 CL7738
8
7
6
5
A+9V 1
CL7701 BAV99-215
D FFC6 SIGNAL1 MIC 2
8.8
4.4
4.4
4.4
CL7702 R7704
MIC GND 3 0
MOTHER CL7703
BOARD SIGNAL2 MIC/GUITAR 4 R7726 C7721 R7730
(1/5) CL7704 R7705 10k 0.1 2.2M
MIC DET2 5 0
CL7705
MIC DET1 6 R7703
CL7706 0 CL7722
MODE SEL 7 C7723
CL7720
R7717 C7714 10
C7702 22p 50V J7701
22k CL7715
0.1 MIC 2
CL7712 CL7725 GUITAR
R7733
E C7701
0.1
C7704
100p
C7706
100p
10k C7728
0.001
CL7726
CL7710
R7708
FB7700 FB7701 10k C7711 R7728
100p 1.2k CL7727
CL7707
C7708
10
50V
R7718 C7722
18k 1
F CL7729 CL7728
0 0
CL7716
3.3 3.3
Q7707 Q7708
C7712 DTC014EUBTL DTC014EUBTL R7732
0.1 2.2M
GAIN CONTROL MUTING
MHC-V41D
52 52
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-10. PRINTED WIRING BOARD - MIC Board - • See page 47 for Circuit Boards Location. 6-11. PRINTED WIRING BOARD - IR Board - • See page 47 for Circuit Boards Location.
• : Uses unleaded solder. • : Uses unleaded solder.
1 2 3 1 2
MIC BOARD (See Note) IR BOARD
(Former MB type)
>01P
R7704
CL7705 C7701
A CL7719
FB7701
R7701
R7707
1 CL7701 FFC6
MOTHER
BOARD A
2 CN601
C7706
CL7700 (Page 48) R7450
JW7705 C7702 CL7454
CL7703
CL7720
FB7700
JW7704 CL7704
6
>11P
(See Note)
IC7450 R7451
7 C7704 MOTHER
(Former MB type) 1
CL7702 BOARD
R7705
R7708
JW7706 CL7706 CN7701 CN601
>02P
CL7723 (Page 50) MOTHER 3
R7703 (New MB type) BOARD C7451 CL7455
CL7452
(See Note) CN127 CL7450 CL7453
C7716 C7708
(Page 48)
C7709 R7725 R7726 3
B C7720
CL7707
C7721 B >12P
CN7451
CL7711 CL7730 1
CL7732 MOTHER 11
BOARD CL7451
R7716 C7719 1-982-787- (11)
CL7733 CN127
C7710 C7715
CL7708 CL7734 (Page 50)
CL7736 1 8 C7711
(New MB type)
CL7709 R7717
CL7731 (See Note)
CL7735 4 5
JW7702 IC7700 Note: The MOTHER board has been changed in the midway of production.
R7722 C7713 CL7712 C7714 Refer to “CHANGE OF MOTHER BOARD” on page 8 for “Former
CL7737 MB type” and “New MB type”.
R7730 R7718
CL7713
C C7712
CL7729
CL7727 C7722
C7718
R7729
C7724 C7723
R7728 CL7728
E
JW7703
E
CL7710 R7733 CL7726 CL7716
Q7708 Q7707
CL7715 R7732 R7734 CL7714 CL7738
JR7701
CL7724
CL7725 CL7722
6-12. SCHEMATIC DIAGRAM - IR Board -
CL7717 CL7721
W7700 1 2 3 4 5
D
(CHASSIS)
C7727 C7728
D7704 CL7718 D7705 IR BOARD
A
K/A
A/K K
A
K A
IC7450
CN7451 REMOTE CONTROL RECEIVER
11 3P IC7450
(11) PNA4823M03S0
1-982-786- R7451
DGND 1
MOTHER CL7450 0 CL7454 2.9 1
BOARD SIRCS 2 VO
(2/5) CL7451 CL7453 2
E E+3.3V 3
CL7455 3.3 3
GND
C7451
B
VCC
0.22
CL7452
J7701 J7700
R7450
MIC 2 MIC 1 22
GUITAR
Refer to “CHANGE OF MOTHER BOARD” on page 8 for “Former
MB type” and “New MB type”.
MHC-V41D
53 53
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-13. PRINTED WIRING BOARD - GESTURE Board - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10
GESTURE BOARD (SIDE A) GESTURE BOARD (SIDE B)

A (See Note)
(Former MB type)
>03P
MOTHER
BOARD
NORTH FFC3
CN120
ELECTRODE
(Page 48)
>13P CL7515
MOTHER
BOARD
CN120
B (Page 50)
(GESTURE CONTROL SENSOR) (New MB type)
(See Note)
K A K A JL7503
JL7504
R7501
D7501 D7503
JL7501 A/K
D7506 A K K A/K D7507
D7505 A A K C7500
A K/A
D7502
2 6 R7500
K CN7500 JL7505
C JL7502
R7507
1 7
JL7500R7502
CL7510
R7519
R7514
R7503 R7506
R7504
K
D7500
WEST EAST R7508 C7505
CL7511
C7504 A
K/A
ELECTRODE ELECTRODE R7509
R7505 14 1 D7504
K A
CL7500
CL7502
CL7504
CL7506
CL7508
C7509
CL7507
R7516
IC7500
C7518
CL7501 15 28
CL7512
CL7505
R7510 CL7509
CL7514 C7508
CL7503 C7511
TRANSMITTER C7506
C7515
C7516
C7503
R7511
R7512
R7515
R7517
D CL7517 CL7513
SOUTH
ELECTRODE
CL7516
11 11
1-982-788- (11) 1-982-788- (11)
MHC-V41D
54 54
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
6-14. SCHEMATIC DIAGRAM - GESTURE Board - • See page 60 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9
GESTURE BOARD
A R7502 R7516
C7509
100p
C7504
100p
R7514
10k
R7519
10k
0 100
D7503
BAV99-215
R7503 R7508
0 100
D7502
BAV99-215 R7504 R7506
100 100
R7505 R7509 C7518

D7501 100p
BAV99-215 100 100
CL7502
CL7507
CL7508
CL7511
D7500
BAV99-215
CL7500
CL7504
CL7506
CL7510
3.3
3.3
3.3
3.3
0
0
14
13
12
10
11
8
7
6
5
4
3
2
1
C
NC_14
MCLR
EIO7/S13
EIO6/S12
EIO5/S11
EIO4/SI0
EIO3
NC_7
NC_6
NC_5
IS2
EIO2
EIO1
EIO0
IC7500
GESTURE CONTROLLER
IC7500
MGC3030
VCAPD
VCAPS
VCAPA
VINDS
VSS1
VSS2
VSS3
VDD
TXD
RX0
RX1
RX2
RX3
RX4
CN7500
7P
D JL7500
15
16
17
18
19
20
21
22
23
24
25
26
27
28
RB520SM-30T2R
RB520SM-30T2R
RB520SM-30T2R
RB520SM-30T2R
3D-INT 1
JL7501
1.4
3.3
3.3
1.4
1.4
1.4
1.4
3
1.8
D7504
D7505
D7506
D7507
FFC3 3D-RESET 2
DGND 3
MOTHER JL7502 C7505
BOARD R7501
3D-DATA 4 0 100p
(3/5) JL7503
C7516
DGND 5 4.7
JL7504
CL7501
CL7503
CL7505
CL7509
CL7512
R7500 C7500 C7503 C7506 C7508 C7511 R7507
3D-CLK 6 0 0.22
JL7505 0.1 2.2 0.1 2.2 10k
D+3.3V 7
E C7515
4.7
R7510 R7511 R7512 R7515 R7517

4.7 10k 10k 10k 10k
CL7514 CL7517 CL7516 CL7513 CL7515

F
TRANSMITTER EAST ELECTRODE SOUTH ELECTRODE WEST ELECTRODE NORTH ELECTRODE
(GESTURE CONTROL SENSOR)
MHC-V41D
55 55
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-15. PRINTED WIRING BOARD - PANEL Board - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8
(AEP, RU, UK, AUS, E4, SP) CN7801
PARTY LED
BOARD REC/PLAY
PANEL BOARD (CHASSIS)
5V 1A
(See Note)
(Former MB type)
A CL7804
D7803
K/A
CL7807 >05P
1 3 4
A K CL7805 MOTHER
CN7002
C7804
W7800 BOARD
CL7801
(See Note) 6
(Former MB type) (New MB type) CL7128 CL7129 CL7170 CL7168 CL7137 CN7801 CN451
R7099
R7095 (Page 48)
R7064
R7065
R7066
R7067
R7069
CL7127 CL7139
>04P >14P JW7806
E Q7002 K
R7093
CL7806 1 4 3
MOTHER MOTHER ND7000 Q7001 D7005 >15P
CL7800
K/A K/A
BOARD BOARD VACUUM FLUORESCENT DISPLAY CL7117 E CL7130 CL7140 C7806 D7801 MOTHER
R7097 CL7135 A
R7068
JW7001 1
CL7112
CL7114
CL7169 CL7126
CL7119
CN103 CN103 D7802 A KA K K BOARD
C7027 C7042
(Page 48) (Page 50) CL7121 CL7124 CL7132 CL7134 CL7138 JR7800 CL7802 CN7800 CN451
C7800
A
CL7097 CL7079
(Page 50)
JW7807
CL7118
D7800
C7041
FFC4 CL7803
CL7123 C7801 (New MB type)
C7031
B
CL7113
JW7829
JW7828
45 44 R7061 16 CL7116 4 2 1 (See Note)
JW7809
CL7153 CL7147 CL7131
JW7805
CL7125
CL7115
JW7804 C7036 CL7120 C7028
JW7810
CL7122
CL7143
JW7803
JW7811
CL7136
JW7825
CL7149
R7058
JW7815 C7040
C7032
CL7155 CL7145 C7038 C7039
C7034
R7060
C7033
R7059
JW7816
JW7808
CL7144 CL7160 CL7133
JW7817
S7016 S7014 19 1 S7013
CN7007
JW7813
MIC ECHO VOICE CHANGER 18 2 C7002 SOUND FIELD
CL7156
CL7158 CL7152 CL7150 CL7148 CL7030
R7072
R7073
R7074
R7075
R7021
C7004
R7020
C7005
R7018
C7006
R7023 CL7033 R7017
JW7838
JW7837
CL7022 CL7146
CL7047 CL7161 CL7141 S7011
CL7052
CL7048
CL7044
CL7142 C7043 PARTY LIGHT
CL7059 CL7039
JW7836
CL7038 CL7159 C7044
CL7067 CL7042 R7013
C
CL7163
CL7036
CL7034
R7028 R7019
R7016 JW7800 JW7824 12 1 CL7027
CL7069
CL7162
JW7814 CL7029
S7012 R7036 S7015
D7001 VOCAL FADER CL7068 C7003 FIESTA
D7001, S7018 CL7157 R7082 13 24 CL7032 D7000
GUITAR
CL7064
IC7000 D7000, S7007
CL7041
CL7031 R7033
C7011 MEGA BASS
JW7833 C7008
S7018 S7007
CL7060
CL7057
CL7053
CL7049
CL7045
CL7043
CL7040
CL7037
CL7035
CL7055
CL7025
CL7065
R7014 R7024
C7012
R7032
C7009
R7030
C7013
R7027
C7010
R7026
C7014
R7025
C7007
R7022
R7015
R7012
CL7151
CL7061
CL7058
CL7054
CL7050
CL7046
CL7164
R7031 CL7028
CL7051
R7009
R7010
S7020 S7010 JW7818
D + MIC/GUITAR LEVEL –
S7017 S7009
W.PARTY CHAIN PARTY CHAIN
CL7066 R7011
R7035 CL7026
S7021 S7008
+ –
R7029 D7003, S7005 D7003
CL7062 PAIRING
E BLUETOOTH
S7019
FUNCTION S7005
CL7070 R7008
R7037 CL7024
R7034
S7023 S7006 D7002, S7022

JW7834
+ VOLUME – GESTURE
CL7154 ON/OFF CL7023
JW7802
R7006
JW7822
CL7072
R7007
D7002
F R7039 CL7021
CL7071 S7022
S7003
S7004
KARAOKE R7038
R7040
CL7075 CL7073
S7000
S7024
PLAYBACK
G
S7025 S7028 S7026
SAMPLER DJ
JW7812 R7042
CL7077
S7027 S7029
H +
TUNING
–
> .
CL7074 S7001 S7002
R7041
R7043 R7004 R7005
CL7076 CL7078 CL7019 CL7020 11
1-982-785- (11)
I
MHC-V41D
56 56
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-16. SCHEMATIC DIAGRAM - PANEL Board - • See page 60 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PANEL BOARD
A NFC
CL7806 CL7802 1 VBUS
CN7801
CN7800 CL7800 D–
BOARD 6P
CL7801 D+ REC/PLAY
VBUS 1 5V 1A
CL7803 4 GND
FFC5
NC 2
D– 3 D7803
DZ2J068M0L
D7801 D7802 BAV99-215
D+ 4
D7800
BAV99-215 BAV99-215
USB_GND 5
CL7805 C7800 C7801 C7806 C7804
SHIELD 6 0.1 100 0.01 0.1
B 10V
CL7804 CL7807
CL7079 JW7001 CL7097 (AEP, RU, UK, AUS, E4, SP)

W7800
R7097 C7027 C7028
10k 0.1 1
(CHASSIS)
C7031 R7058 C7032 C7033 C7034 C7036 C7038
R7064 100
R7065 100
R7066 100
R7067 100
R7068 100
R7069 330
R7093 330
R7060 0.1 56k 0.1 100p 100p 100p 2.2
C7041 0.1
C7042 1
100 50V
UDZVTE-172.0B
CL7141 R7059
D7005
MOTHER
BOARD 100
(4/5) CL7142
R7061
CN7007 R7075 R7074 R7073 R7072 C7044 C7043 100
19P 56 56 56 56 0.01 0.01
CL7143 C7004 C7005 C7006 Q7001
M+5.2V 1 47p 47p 47p NSS40200LT1G
CL7144 5.1 5.1
LED_GND 2
CL7145
C7002 C7003 R7099
D
FL_CLK 3
CL7029
CL7034
CL7036
CL7039
CL7163
CL7059
CL7162
CL7067
CL7146 10 0.22 10k
SW+12V 4 16V
4.4
R7021 100
R7020 100
R7018 100
CL7147
FL_SOUT 5
CL7148 CL7170
FL_LATCH 6 R7095
CL7042
CL7044
CL7048
CL7052
CL7149 680
POWER_KEY 7
CL7150 Q7001, 7002
FFC4 AD_KEY0 8 B+ SWITCH
3.2
1.1
1.1
1.4
1.4
CL7151
0
0
DGND 9 CL7168
CL7152
10
12
11
1
2
3
4
5
6
7
8
9
SW_LED_BLUE 10
CL7153
GND
SIN
SCK
TRANS
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
0
E
SW_LED_RED 11
IC7000
C7039 2.2 50V
C7040 2.2 50V

CL7154 6.1
AD_KEY1 12
CL7155
DGND 13 LED DRIVER Q7002 CL7169
CL7156 DTC014EUBTL
CL7123
CL7130
CL7137
CL7139
CL7118
CL7117
CL7116
CL7115
SW LED IC7000
SW_LED_GREEN 14
CL7113
BOARD CL7157 TC62D723FNG
D+3.3V 15
CL7158
PWMCLK
RGB_SD 16
CL7159
OUT15
OUT14
OUT13
OUT12
OUT10
OUT11
CL7120
CL7121
CL7122
CL7124
CL7125
CL7126
CL7131
CL7132
CL7133
CL7134
CL7135
CL7136
CL7138
CL7140
SOUT
CL7119
REXT
OUT9
OUT8
VDD
RGB_SCLK 17
CL7112
CL7114
CL7160
RGB_TRANS_PNL_LED 18
CL7161
24
23
22
21
20
19
18
17
16
15
14
13
F
RGB_PWM 19 3.3
1.6
2.1
2.3
1.2
1.2
1.1
2.3
1.3
C2P
C1P
F+
F+
STB
CLK
DIN
OSC
VDD
VH
VIN
C2N
C1N
LGND
PGND
F–
F–
CL7037
CL7043
ND7000
VACUUM FLUORESCENT DISPLAY
CL7032
CL7035
CL7040
CL7045
CL7049
CL7053
CL7057
CL7060
CL7064
CL7068
C7011 0.01
C7008 0.01
R7022
100 C7012 0.01
G C7009 0.01
C7013 0.01
R7015
820 C7010 0.01
C7014 0.01
CL7164
R7025 47
R7026 47
R7027 47
R7030 47
R7032 47
R7033 47
R7036 47
R7012 C7007
H 82 47p
CN7002
CL7046
CL7050
CL7054
CL7058
CL7061
CL7065
CL7069
4P
CL7127
R7082 1 M+5.2V
0
2 NC PARTY
CL7128 LED
3 GREEN HILED BOARD
CL7129
4 BLUE HILED
I
D7000 D7001 D7002 D7003
HL-364V620MZ-JS HL-3TES22OD-BF-SN HL-3TMH234WW-3.7-HK-BF-SN-J HL-364B460MZ-JS
MEGA BASS GUITAR GESTURE PAIRING

ON/OFF BLUETOOTH
CL7019 CL7020 CL7021 CL7023 CL7025 CL7027 CL7030 CL7033 CL7041 CL7051 CL7062 CL7071 CL7073 CL7075 CL7077
J R7004 R7005 R7007 R7009 R7010 R7013 R7017 R7019 R7024 R7029 R7034 R7038 R7040 R7042
680 1k 1.5k 1.5k 2.2k 3.3k 4.7k 6.8k 10k 15k 22k 33k 68k 150k
S7001 S7002 S7003 S7005 S7007 S7009 S7011 S7013 S7015 S7017 S7019 S7022 S7024 S7026 S7028
PAIRING MEGA BASS PARTY CHAIN PARTY LIGHT SOUND FIELD FIESTA W.PARTY CHAIN FUNCTION GESTURE PLAYBACK DJ SAMPLER
BLUETOOTH ON/OFF
K CL7022 CL7024 CL7026 CL7028 CL7031 CL7038 CL7047 CL7055 CL7066 CL7070 CL7072 CL7074 CL7076 CL7078
R7006 R7008 R7011 R7014 R7016 R7023 R7028 R7031 R7035 R7037 R7039 R7041 R7043
680 1k 1.5k 1.5k 2.2k 3.3k 4.7k 6.8k 10k 15k 22k 33k 68k
L
S7000 S7004 S7006 S7008 S7010 S7012 S7014 S7016 S7018 S7020 S7021 S7023 S7025 S7027 S7029
KARAOKE – VOLUME MIC/CUITAR LEVEL VOCAL FADER VOICE CHANGER MIC ECHO GUITAR MIC/CUITAR LEVEL VOLUME + TUNING + – TUNING
– +
MHC-V41D
57 57
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-17. PRINTED WIRING BOARD - SMPS Board - • See page 47 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
SMPS BOARD
A JL6300 R6338 JL6306 Q6507 JL6527

C6305 A C6309 JL6500 R6503 R6512 R6544 E R6541
F6000 R6313 (AEP, RU, UK, AUS, E4, SP)
R6320 1 3 R6500
G C6522 R6540
Q6307
D6341 C6315 D PH6300 C6502 E
K D6303 C6521
JW6001
Q6500
JW6015
A K R6327 S 2 4 R6542
R6341 D6300 D6516 Q6506 ET6501
C6340 JL6529 R6543 E JL6525
K A R6551 K A
JL6307 K R6518 R6517
JL6000 C6312 R6546
JW6000
R6501 D6515 R6516 (CHASSIS)
IC6300 IC6500
D6511
D6306 4 2 A A K
R6328 R6545
C6307 JW6004
JW6016
K A PH6302 2 1
D6510
4 1
C6007 C6300 3 1 A JL6522 JL6523 C6511
JW6025 C6313
R6339
D6500 K R6537 3 4
R6321 A K
R6336 A JL6521 R6515
B JL6001 5 8
A
C6317
JR6004
JL6308
K
JL6530 K A
D6509
R6507 R6509
C6509 C6510
VR6000 D6308 4 2 R6508 JL6524
D6505
Q6305
JW6003 R6502 A
2 E PH6301
CN6001 K R6514
LN6002 D6311 3 1 D6503
JL6305 Q6304
- AC IN PATTERN D6340 R6520
A K
A K R6334 K
JW6005
SPARK-GAP A K JL6528
JW6024
R6310 R6340 R6307 C6504
D6313 R6330 C6319
TH6300 D A
R6333 JW6012 JL6303 R6504 R6505 R6525
JL6538 D6502
K D6312 A JL6535
K
R6315
R6335 JL6536 JW6019
1 JL6309 JL6304 R6312 JL6534
C LF6001
LINE FILTER
R6316 JL6526
JS6505 JW6017
Q6302
JL6002
Q6301 9 10
C6311 E JL6508 JR6005
G
FB6301 T6300 JW6029
JW6027
POWER TRANSFORMER
D
E
C6310
C6501 (AEP, RU, UK, AUS, E4, SP)
Q6303
C6524
JS6300
R6306 S
JW6006
R6554
JW6026
D6501
JW6008
JW6023
JW6022
JL6301 C6303 7
C6000 R6304
C6006 C6503
D R6309
Q6300
G JL6509
R6302
A6931 F6500 JL6507
LN6001 JL6302
FB6300 D
C6003 PATTERN SPARK-GAP
A6933
5
JW6020
S
JL6517 JL6504 JL6512
R6301 R6319
11
JS6504
R6305 (See Note)
C6320
JW6030
JW6007
LF6000 (Former MB type)
JW6013
LINE FILTER
D6504 >06P
JL6542 MOTHER
C6507
C6529
R6300 R6318 D6307
E
BOARD
CN001
(Page 48)
JS6503
C6523
LN6000 C6314
PATTERN SPARK-GAP JL6516
>16P
MOTHER
4 3
JL6506 BOARD
JW6002 D6001 C6500 CN001
3
R6326 1 18 JL6503 C6515 (Page 50)
JS6000
(New MB type)
TH6000 2 1 (See Note)
1
JL6541
R6322 C6505 NO6501
F JW6009 JL6514
JW6021
R6550
JS6501
JS6302
JL6510
Q6504 E (AEP, RU, UK, AUS, E4, SP)
C6321 R6538 JL6520 JW6011
JL6515
R6555
R6549
JL6518
JL6511
A6932
C6302
3 JL6533
C6506
1 JL6531
JL6519
2 Q6501
G 4 D6000 E
R6539
JW6018
ET6000 R6535 ET6500
R6548
JW6010 R6533
JW6028
JL6532 R6536 (AEP, RU, UK, AUS, E4, SP)
R6521 R6523
9 3 1
JW6014 JL6513 CN6500
11, 12
1-982-604- (11, 12)
H
(CHASSIS) (CHASSIS)
>07P >17P
MOTHER MOTHER
BOARD BOARD
CN2007 CN2007
(Page 49) (Page 51)
(Former MB type) (New MB type)
(See Note)
MHC-V41D
58 58
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
6-18. SCHEMATIC DIAGRAM - SMPS Board - • See page 60 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
SMPS BOARD CN6500

A JL6513
8P
9 V1
JL6514
R6548 8 V1
2.7k JL6515
3W 7 V1
JL6516
6 V1
R6549 JL6517
2.7k 5 V1_GND
3W JL6518
4 V1_GND
JL6519
R6550 3 V1_GND
R6322 R6326 C6314 2.7k
B D6000
47k
3W
47k
3W
0.0047
800V
JL6542 3W
JL6520
2 NC
3 D15JAB80 1 V1_GND
+ D6504
1 2 C6500 C6529 C6507 C6505 C6506
FCF10A40 470p 0.1 0.1 470 470 R6555
~ ~ ET6500
2kV 250V 250V 80V 80V 0
– D6001
E
2 LB10S D6307
T6300 R6533
4 R6318 R6319 SARS10
R6536 1000p R6554
~ 3.3k 3.3k POWER TRANSFORMER 630V ET6501 (CHASSIS) MOTHER
4 3 47k 0
– + 1 18 BOARD
E
~ (5/5)
C6302 C6321 R6535
TH6000 1 390 0.001 47k (CHASSIS)
C 450V JS6302 250V JS6501
2 17
C6501
470p
NO6501 (AEP, RU, UK, AUS, E4, SP)
11P
2kV
LN6000 3 16 JS6503 JL6503
PATTERN 1 A-Supply
SPARK-GAP
C6515 2 NC
4 15 0.1 JL6504
3 AGND
C6311 JS6504
ET6000 LF6000 47p 4 M-Supply
R6315 1kV JL6506
LINE FILTER 4.7
5 14
C6523
23.2 5 M-Supply
E
Q6300 - 6303 F6500 0.1 JL6507

C6310 6.3A JL6531
POWER SWITCH 0.9 47p 6 M/DGND
(CHASSIS) 250V JL6508
D JS6000
145.2
Q6302
1kV 13
0.3 JL6509
7 M/DGND
Q6301 1 2SCR543RTL R6335 JL6533 R6539 8 AC-DET
TK10A80W 0.47 7 12 0.7 1k JL6510
FB6301
JL6309
0.9 9 MAIN ON
Q6504 JL6511
C6003 C6006
0.1 R6312 PZTA42G 10 Network ON
JL6304
JL6302
0.0022 D6501 JL6512
250V 310V 100 JS6300
8 11
FCH08A15 0 POWER
S JL6532 R6523 11 Latch ON
0.7 CONTROL 1k
C6000
0.0022 LN6001 145.2 Q6300 R6309 Q6303 R6333 D6312 C6319 9 10 Q6501
250V PATTERN TK10A80W 100 1 2SAR543RTL 3.3k RF101LP4S 47 C6524 C6503 PZTA42G R6521 R6538
SPARK-GAP 100V 1 1200 POWER
0.9 0.9 10k 10k
35V CONTROL
E FB6300
DZ2J27000L
C6303 R6306 C6320 R6305 R6330 PH6301
LF6001 220p 4.7k 220p
S
4.7k 30.5 4.7k EL816S1(B)(TA)(DTE-S)
D6313
LINE FILTER 2kV 2kV R6316 23.9 ISOLATOR
2.2
1.5 3 1 57.8 R6502 D6502 R6525 R6537 D6515 R6542 R6540
Q6304 1.8k DA2J10100L 0 2.2k DZ2J24000L 47k 1k
JL6303 23.2 2SC2655L-Y 56.8
4 2
REGULATOR
VR6000
DZ2J220M0L
R6514 R6520 D6509 R6545
D6503 68k 33k 100k
D6311
DA2J10100L DZ2J220M0L
JL6530
C6007
DZ2J220M0L
R6321 C6307 C6313 D6308 C6317
F 0.33 100k 0.47 100 DZ2J24000L 470p R6515 C6510 R6546 R6543
D6510
310V D6500
35V 68k 0.001 100 8.2k
23.2
110
DZ2J120M0L
0.9
JL6521
JL6000 R6334
5
1k D6505 R6516 C6511 D6516

47k 0.001 DA2J10100L
DRV
VCC
HV
DZ2J120M0L
F6000
IC6300
10A
250V
Q6506
JL6528
JL6525
R6508 2SCR523UBTL
JL6001 JL6002 POWER CONTROL 270
0 LATCH SWITCH
CN6001
IC6300
- AC IN LN6002 NCP1240AD100R2G
0.6
PATTERN R6507 R6517
G 2
SPARK-GAP 270 JL6524 1k
0.6
Q6507
2SCR523UBTL
LATCH SWITCH
LATCH
R6336 R6551
GND
JL6527
23.2 R6509 0
JL6523
100k 10k C6509 R6504
CS
FB
1 120k
Q6305 23.7 0.047 15k
2PB709ART
4
3
2
LATCH SWITCH JL6522

R6339 R6338
JL6526
0
1.5
1.1
-1.6 1k 10k
C6522 R6544 C6521 R6541 R6512

0.001 22k 0.001 10k 100
D6340 R6340
H DA2J10100L 39k
JS6505
0 0
JL6305
D6341
DA2J10100L
32.3
JL6500 0.6

JL6536
3 4 Q6500
R6341 R6500 C6502 R6503 2SCR523UBTL
R6310 R6313 12k
IC6500 100k 0.01 220k
Vref
R6300 AC DETECT
0 1.5k
2M D6306
R6328
DA2J10100L
4.7k SHUNT REGULATOR
IC6500
I R6301 MM1431CURE
A
DZ2J300M0L
2M TH6300 R6505
15k
D6303
2 1
R6302 R6304 R6307 C6305 C6340 C6309 C6312
2M 0.05 330k 470p 0.001 0.0047 0.01 PH6302
5W EL816S1(B)(TA)(DTE-S) R6518 C6504
D6511 8.2k 2.2
ISOLATOR DZ2J220M0L 100V
JL6308 23.9 3 1 -0.1
0 4 2
0
R6501
R6320 100k
JL6300
470k Q6307
3.1 RHK005N03T146
JL6301
J AC DETECT PH6300
EL816S1(B)(TA)(DTE-S)
ISOLATOR
S JL6306
C6300 R6327 C6315 1 1 3 15.6
D6300
DZ2J100M0L 0.22 220k 0.01
JL6307 0 15.6
2 4 JL6529
MHC-V41D
59 59
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
• IC Block Diagrams – SMPS Board –

IC6300 NCP1240AD100R2G
– GESTURE Board – VCC MIN
VDD
IC7500 MGC3030 VCC ON VHV DC
SAMPLE
VCC OVP
OVP CMP 8 HV
CMP BROWN OUT +
28 VCAPD + 50 us OVP VCC OVP 10 us +
AC OFF
27 VSS3 FILTER FILTER
VCC OVP
26 VCAPA
V OVP
A/D SIGNAL UVLO
LOW POWER POWER MANAGEMENT 25 RX4 OTP CMP CMP
CONVERTER CONDITIONING LATCH 1
WAKE-UP UNIT (PMU) UVLO + DUAL HV
350 us OTP
EIO0/TS 1 + SG & X2 & VCC START-UP
FILTER
V CLAMP
A/D SIGNAL CURRENT
VCC OFF
CONTROL
EIO1 2 FLASH 24 RX3
V OTP
CONVERTER CONDITIONING TSD SOURCE
EIO2 3 MEMORY
INTERNAL BUS
IS2 4
A/D SIGNAL LATCH ON CMP VCC INT
NC 5 GESTURE PORT 23 RX2 S Q + 6 VCC
CONVERTER CONDITIONING
SS END
NC 6 AND INTERFACE BROWN OUT
VCC VCC REGULATOR
NC 7 SELECTION VDD REG
VCC ON
RESET R +
IC START B
A/D SIGNAL
EIO3 8 22 RX1
CONVERTER CONDITIONING STOP
SIGNAL OFF MODE VDD
VCC (REG)
CMP1 CMP
PROCESSING
A/D SIGNAL + IC START +
UNIT (SPU) 21 RX0 S Q
CONVERTER CONDITIONING
VCC MIN

COMMUNICATION RESET +
V ON
EIO4/SI0 9 20 VSS2 R
CONTROL (I2C) VOLTAGE REFERENCE
EIO5/SI1 10 19 VINDS OFF MODE
VCC RESET
(VREF) OSC 65kHz POWER ON
EIO6/SI2 11 18 VCAPS CMP2 RESET CMP
EIO7/SI3 12 17 VDD VFB (REG) GO TO OFF MODE JITTERING FM INPUT SQUARE OUTPUT
16 VSS1 + TIMER 500 ms
TON MAX OUTPUT
V OFF
MCLR 13 RESET BLOCK INTERNAL
TX SIGNAL GENERATION 15 TXD FREQ FOLBACK PFM INPUT SAW OUTPUT
NC 14 CLOCK
FB BUFFER CS REF RAMP OTA

FB 2 +
+
OFFSET
V RAMP
MAX TON
SKIP CMP
SAMPLE
VHV DC
+ SKIP B
VCC

V SKIP
+
V to I CLAMP
– PANEL Board –
PWM CMP
PWM
VFB (OPC)
VDD
IC7000 TC62D723FNG +
IC STOP B
S Q 5 DRV
R
SOFT START CMP
24 VDD
BROWN OUT B
CS 3 LEB 250ns +
POR
LATCH B
23 REXT
FAULT B
GND 1 ENABLE
CIRCUIT SOFT START
TIMER SS END
ITRAN CMP
+ ITRAN
SOUT S Q TRANSIENT TIMER UP/DOWN
F/F
VCS (TRAN)
SELECTION 22 SOUT
SIN 2
CIRCUIT R
16-bit SHIFT REGISTER
SCK 3
ILIMIT CMP MAX TON
Q FAULT
+ ILIMIT S FAULT TIMER RESET

LATCH MANAGEMENT
COMMAND 16-bit ×2 IC STOP
DATA TRANSFER
TRANS 4 CONTROL STATE SETTING R LATCH
V ILIM
CONTROL CIRCUIT AUTO RECOVERY
CIRCUIT REGISTER CS STOP CMP
TIMER
GND 4 LEB 120ns +
4 EVENTS TIMER

VCS STOP
BROWN OUT
TSD
TSD
PWM DATA
REGISTER
COMPARATOR PWM
21 PWMCLK
COUNTER
OUTPUT ON/OFF POD

SETTING DATA CIRCUIT
REGISTER
OUTPUT
DELAY
CIRCUIT
CONSTANT TSD
8-bit DAC
CURRENT CIRCUIT
OUTPUT
CIRCUIT
REFERENCE
VOLTAGE
ERROR
DETECTION
RESULT DATA
REGISTER
OUT0 5 OUTPUT 20 OUT15

OUT1 6 OPEN/SHORT 19 OUT14
OUT2 7 DETECTION 18 OUT13
CIRCUIT
OUT3 8 17 OUT12
OUT4 9 16 OUT11
OUT5 10 15 OUT10
OUT6 11 14 OUT9
OUT7 12 13 OUT8
MHC-V41D
60 60
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
SECTION 7 Ver. 1.1
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • The mechanical parts with no reference
The components identified by mark 0
they may have some difference from the number in the exploded views are not sup-
or dotted line with mark 0 are critical for
original one. plied.
safety.
• Items marked “*” are not stocked since • Color Indication of Appearance Parts Ex-
Replace only with part number specified.
they are seldom required for routine ser- ample:
vice. Some delay should be anticipated KNOB, BALANCE (WHITE) . . . (RED)
when ordering these items.   The components identified by mark 9 con-
Parts Color Cabinet’s Color tain confidential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
7-1. SIDE PANEL SECTION
#2 top panel section
(AEP, RU, UK, AUS, E4, SP)

#1 #1
C
#1 F
#2 E not supplied
G
#1 B A (Included Ref. No. 60
#1 : page 62)
#1
#1
2 #1 D
F
loading panel section E G #1
D
B C A
#2
not supplied
#1 #1
#1 #1
#1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-726-160-01 PANEL, SIDE (R) (for Right side) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
2 4-726-159-01 PANEL, SIDE (L) (for Left side) #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
61
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
7-2. TOP PANEL SECTION

56
55
51
54 51
51
FFC6
not supplied 57 (See Note 2)
MIC1
51 58
not supplied
(MIC COVER board) FFC5
59
51
53
not supplied
(GESTURE board)
(AEP, RU, UK, AUS, E4, SP) 52 51
FFC4
51
51
51
51
51
not supplied 60
51
not supplied
51 51
51 51
51 51 51 Note 2: Since Ref. No. FFC3 and Ref. No. FFC6 have the
51 not supplied same number of cores, be careful not to mistake the
51 connectors to be connected absolutely. If it connect
51 them to the wrong connector, this unit is damaged.
Be sure to check the color of flexible flat cable,
FFC3 before connecting the Ref. No. FFC3 or Ref. No.
Note 1: When the complete NFC board (Ref. No. 58) is (See Note 2) FFC6 to the connector.
replaced, refer to “NFC OPERATION CHECK- Refer to “2-3. TOP PANEL BLOCK-1” on page 11
ING METHOD” on page 6. for connection location.
51 4-951-620-51 SCREW (2.6), +BVTP (L = 8.0 mm) 60 A-2192-235-A PANEL BOARD, COMPLETE
52 4-726-149-01 BUTTON, DJ (E93, BR, AR, TH, IND, LA)
(PLAYBACK, DJ, SAMPLER, KARAOKE)
53 4-726-148-01 BUTTON, START (N, x, ., >) 60 A-2218-978-A PANEL BOARD, COMPLETE
54 X-2595-700-1 BUTTON, FIESTA ASSY(PARTY LIGHT, (AEP, RU, UK, AUS, E4, SP)
SOUND FIELD, MEGA BASS, FIESTA, FFC3 1-972-242-11 FLEXIBLE FLAT CABLE (7P) (L = 260 mm) (White)
PARTY CHAIN, W.PARTY CHAIN, BLUE TOOTH, (See Note 2)
FUNCTION, , GESTURE ON/OFF, 1) FFC4 1-972-241-11 FLEXIBLE FLAT CABLE (19P) (L = 270 mm)
55 4-725-453-03 PANEL, TOP FFC5 1-972-246-11 FLEXIBLE FLAT CABLE (6P) (L = 210 mm)
FFC6 1-972-244-11 FLEXIBLE FLAT CABLE (7P) (L = 240 mm) (Silver)
56 4-723-058-01 WINDOW, DISPLAY (See Note 2)
57 A-2192-236-A MIC BOARD, COMPLETE
58 A-2194-756-A NFC BOARD, COMPLETE (See Note 1) MIC1 1-852-158-11 MICROPHONE, ELECTRET CAP
59 X-2595-701-1 BUTTON, GUITAR ASSY (VOICE CHANGER,
MIC ECHO, VOCAL FADER, GUITER,
MIC/GUITER LEVEL - +, - +, - VOLUME +, Z)
62
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
7-3. LOADING PANEL SECTION
#2
H
#2
CDM block section
#1
#1
H
rear panel section
103
not supplied
not supplied not supplied
not supplied
102
101
not supplied
not supplied
101 4-726-162-01 PANEL, LOADING #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
102 4-536-754-01 SPRING (LP) #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
103 4-588-651-01 LOADING, BASE
63
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
7-4. REAR PANEL SECTION
152
not supplied
153
152
not supplied
152 not supplied not supplied
not supplied 152 #1

not not supplied
M1 #1 not supplied
supplied
#1
#1 not supplied
not
supplied #1
#1
#1
not supplied
#1 #1
chassis section
#1 154
#1
151 #1
151
151
#1 #1 #1 #1 #1 #1 #1
151 #1 #1 #1 151 #1 #1 151

– Rear view –
151 4-874-614-12 SCREW (1) (3.5X14), TAPPING 0 M1 1-855-006-41 FAN, DC
152 4-951-620-51 SCREW (2.6), +BVTP (L = 8.0 mm)
153 A-2192-239-A PARTY LED BOARD, COMPLETE #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
154 4-726-156-01 PANEL, REAR
64
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.1
7-5. CHASSIS SECTION
#2
#2 K
#2 #2
#2 #2
#2 #2 J #2
L
#2 203 M
#2
not supplied
202 N
204
201
#2 not supplied 201
201 201
not supplied
not supplied
#2
front panel section K N #2 201
not supplied
Note 1: Make sure perform discharge processing before

removing the complete SMPS board (Ref.
No. 202) or complete MOTHER board (Ref.
No. 203). For the discharge processing meth-
od, refer to “CAPACITOR ELECTRICAL
DISCHARGE PROCESSING” on page 5.
Note 2: When the complete MOTHER board (Ref.

No. 203) is replaced, refer to “DESTINA-
TION SETTING METHOD” and “NFC OP-
ERATION CHECKING METHOD” on page
6.
201 4-874-614-02 SCREW (1) (3.5X14), TAPPING 9 203 A-2222-153-A MOTHER BOARD, COMPLETE (SV) (BR)
202 A-2203-074-A SMPS BOARD, COMPLETE (See Note 1, 2)
(E93, BR, AR, TH, IND, LA) (See Note 1)
202 A-2218-781-A SMPS BOARD, COMPLETE 204 3-252-833-01 SCREW (M3), (+) P (L = 8.0 mm)
(AEP, RU, UK, AUS, E4, SP) (See Note 1) #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
9 203 A-2201-879-A MOTHER BOARD, COMPLETE (SV)
(Except BR) (See Note 1, 2)
65
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
7-6. FRONT PANEL SECTION
not supplied
255 (IR board) O
SP2 P
255 253
253
not
supplied
256
251 255 O P
255
SP4
not supplied
not supplied
253
253
speaker cabinet section

254
253
252
251 X-2595-366-1 PANEL, FRONT ASSY 256 4-726-139-01 WINDOW, IR
252 4-592-164-21 FOOT, RUBBER SP2 1-859-277-12 LOUDSPEAKER (34 mm) (Tweeter: L-ch)
253 4-951-620-51 SCREW (2.6), +BVTP (L = 8.0 mm) SP4 1-859-277-12 LOUDSPEAKER (34 mm) (Tweeter: R-ch)
254 A-2192-240-A SW LED BOARD, COMPLETE
255 4-986-971-12 +BV TAPPING SCREW TYPE-2 3.5 (L = 10.0 mm)
66
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
7-7. SPEAKER CABINET SECTION
not supplied
302
SP1
302
302
302 302
SP3
302
302
302
301
301
SP5
301
303
301
303 303
301
301
303
301 301
301 4-238-407-12 SCREW (1) (4X20), +BV TAPPING SP3 1-859-278-11 LOUDSPEAKER (69 mm) (Midrange: R-ch)
302 4-874-614-02 SCREW (1) (3.5X14), TAPPING
303 4-592-164-01 FOOT, RUBBER SP5 1-859-276-11 LOUDSPEAKER (260 mm) (Subwoofer)
SP1 1-859-278-11 LOUDSPEAKER (69 mm) (Midrange: L-ch)
67
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
7-8. CDM BLOCK SECTION
#2
#2
#2
DVD mechanism deck section

(CDM90-DVBU204)
#2
353
352
353
354
354
352 354 not supplied

354 353
not supplied
352
353
355 352
355
351
not supplied
#2
not supplied
351
351 4-533-939-01 SPRING, INSULATOR (F) (for Front side) 355 4-533-940-01 SPRING, INSULATOR (R) (for Rear side)
352 4-533-382-01 INSULATOR
353 4-533-702-01 STEP SCREW #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
354 2-345-115-01 SCREW (S), FLOAT (L = 7.0 mm)
68
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
7-9. DVD MECHANISM DECK SECTION (CDM90-DVBU204)
CDM1
402
OP1
401
403 402
402
401
401
402 not supplied
401
MS-476
board
FFC2
FFC1
401 2-634-618-21 INSULATOR FFC2 1-972-243-11 FLEXIBLE FLAT CABLE (5P) (L = 230 mm)
402 3-087-599-01 INSULATOR SCREW 0 OP1 A-2046-956-A OPTICAL PICK-UP BLOCK (CMS-S76RFS7G) (SV)
403 4-418-987-01 SHEET (S76) (Including Sled motor, Spindle motor, Sheet)
CDM1 A-1937-669-D CDM90 ASSY (Including MS-476 board)
FFC1 1-972-245-11 FLEXIBLE FLAT CABLE (24P) (L = 200 mm)
69
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2 SECTION 8
GESTURE IR MIC
ELECTRICAL PARTS LIST
MOTHER MS-476 NFC
Note:
• Due to standardization, replacements in • CAPACITORS When indicating parts by reference num-
the parts list may be different from the uF: μF ber, please include the board name.
parts specified in the diagrams or the com- • COILS
ponents used on the set. uH: μH The components identified by mark 0
• -XX and -X mean standardized parts, so • SEMICONDUCTORS or dotted line with mark 0 are critical for
they may have some difference from the In each case, u: μ, for example: safety.
original one. uA. . : μA. . , uPA. . , μPA. . , Replace only with part number specified.
• Items marked “*” are not stocked since uPB. . : μPB. . , uPC. . , μPC. . ,
they are seldom required for routine ser- uPD. . : μPD. . The components identified by mark 9 con-
vice. Some delay should be anticipated Among mounted electrical parts on each tain confidential information.
when ordering these items. board, only parts that are described in the Strictly follow the instructions whenever the
• RESISTORS electrical parts list can be replaced for re- components are repaired and/or replaced.
All resistors are in ohms. pairing.
METAL: Metal-film resistor. The parts that are not described in the
METAL OXIDE: Metal oxide-film resistor. electrical parts list cannot be replaced with
F: nonflammable single for repairing.
GESTURE BOARD < JACK >
**************
J7700 1-822-967-12 JACK (MIC 1)
< CONNECTOR > J7701 1-822-967-12 JACK (MIC 2 GUITAR)
CN7500 1-785-466-41 CONNECTOR, FFC/FPC 7P < JUMPER RESISTOR >
< DIODE > JR7701 1-216-296-11 SHORT CHIP 0
D7500 6-500-400-01 DIODE BAV99-215 < TRANSISTOR >

D7501 6-500-400-01 DIODE BAV99-215
D7502 6-500-400-01 DIODE BAV99-215 Q7707 6-552-936-01 TRANSISTOR DTC014EUBTL
D7503 6-500-400-01 DIODE BAV99-215 Q7708 6-552-936-01 TRANSISTOR DTC014EUBTL
* D7504 6-503-578-01 DIODE RB520SM-30T2R *************************************************************
* D7505 6-503-578-01 DIODE RB520SM-30T2R 9 A-2201-879-A MOTHER BOARD, COMPLETE (SV) (Except BR)
* D7506 6-503-578-01 DIODE RB520SM-30T2R (See Note 1, 4)
* D7507 6-503-578-01 DIODE RB520SM-30T2R 9 A-2222-153-A MOTHER BOARD, COMPLETE (SV) (BR)
(See Note 1, 4)
< IC > ***********************
IC7500 6-722-772-01 IC MGC3030 < IC >

*************************************************************
IC001 6-721-079-01 IC TPS542941PWPR
IR BOARD IC002 6-722-439-01 IC BDJ2FC0WEFJ-E2
******** IC004 6-721-872-01 IC 78D09AG-TN3-R
IC006 6-721-766-01 IC 78D05AG-TN3-R
< IC > IC008 6-722-001-01 IC 78D12AG-TN3-R
IC7450 6-600-768-01 IC PNA4823M03S0 ( ) IC009 6-721-079-01 IC TPS542941PWPR

************************************************************* IC305 6-719-198-01 IC MM3411A33URE
IC1000 6-718-999-01 IC MM1839A50NRE
A-2192-236-A MIC BOARD, COMPLETE IC2001 6-723-247-01 IC TAS5534DGGR-S
******************* IC2002 6-723-793-01 IC TAS5634 (See Note 2)
*************************************************************
< CONNECTOR >
MS-476 BOARD
CN7701 1-779-275-11 CONNECTOR, FFC (LIF (NON-ZIF)) 7P ************
< DIODE > When the MS-476 board is defective, replace the CDM90 ASSY (Ref. No. CDM1).
*************************************************************
D7704 6-500-400-01 DIODE BAV99-215
D7705 6-500-400-01 DIODE BAV99-215 A-2194-756-A NFC BOARD, COMPLETE (See Note 3)
********************
< FERRITE BEAD >
When the NFC board is defective, replace the complete mounted board.
FB7700 1-414-813-11 FERRITE, EMI (SMD) (2012) *************************************************************
FB7701 1-414-813-11 FERRITE, EMI (SMD) (2012)
< IC > Note 2: When the IC2002 on the MOTHER board is replaced,
refer to “SPREADING OF COMPOUND” on page 7.
IC7700 8-759-425-23 IC BA4558F-E2
Note 3: When the NFC board is replaced, be sure to refer to “NFC
OPERATION CHECKING METHOD” on page 6.
Note 1: When the MOTHER board is replaced, be sure to refer
to “DESTINATION SETTING METHOD” and “NFC Note 4: The MOTHER board has been changed in the midway of production.
OPERATION CHECKING METHOD” on page 6. Refer to “CHANGE OF MOTHER BOARD” on page 8 for details.
70
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
PANEL PARTY LED SMPS SW LED
A-2192-235-A PANEL BOARD, COMPLETE S7025 1-762-875-21 SWITCH, KEYBOARD (Z)
(E93, BR, AR, TH, IND, LA) S7026 1-762-875-21 SWITCH, KEYBOARD (DJ)
A-2218-978-A PANEL BOARD, COMPLETE S7027 1-762-875-21 SWITCH, KEYBOARD (TUNING + >)
(AEP, RU, UK, AUS, E4, SP) S7028 1-762-875-21 SWITCH, KEYBOARD (SAMPLER)
********************* S7029 1-762-875-21 SWITCH, KEYBOARD (– TUNING .)
*************************************************************
< CONNECTOR >
A-2192-239-A PARTY LED BOARD, COMPLETE
CN7801 1-819-866-11 USB CONNECTOR (A) ( REC/PLAY 5V 1A) *************************
< DIODE > When the PARTY LED board is defective, replace the complete mounted board.
*************************************************************
D7000 6-504-215-11 LED HL-364V620MZ-JS (MEGA BASS)
D7001 6-504-458-01 LED HL-3TES22OD-BF-SN (GUITAR) A-2203-074-A SMPS BOARD, COMPLETE
D7002 6-504-214-21 LED HL-3TMH234WW-3.7-HK-BF-SN-J (E93, BR, AR, TH, IND, LA)
(GESTURE ON/OFF) A-2218-781-A SMPS BOARD, COMPLETE
D7003 6-504-213-11 LED HL-364B460MZ-JS (AEP, RU, UK, AUS, E4, SP)
( PAIRING BLUETOOTH) *********************
D7005 6-503-605-01 DIODE UDZVTE-172.0B
When the SMPS board is defective, replace the complete mounted board.
D7800 6-502-970-01 DIODE DZ2J068M0L *************************************************************
D7801 6-500-400-01 DIODE BAV99-215
D7802 6-500-400-01 DIODE BAV99-215 A-2192-240-A SW LED BOARD, COMPLETE
D7803 6-500-400-01 DIODE BAV99-215 ***********************
< IC > When the SW LED board is defective, replace the complete mounted board.
*************************************************************
IC7000 6-719-142-01 IC TC62D723FNG
MISCELLANEOUS
< JUMPER RESISTOR > **************
JR7800 1-216-296-11 SHORT CHIP 0 CDM1 A-1937-669-D CDM90 ASSY (Including MS-476 board)
< FLUORESCENT INDICATOR TUBE > FFC2 1-972-243-11 FLEXIBLE FLAT CABLE (5P) (L = 230 mm)
FFC3 1-972-242-11 FLEXIBLE FLAT CABLE (7P) (L = 260 mm) (White)
ND7000 1-483-549-11 VACUUM FLUORESCENT DISPLAY (See Note)
< TRANSISTOR >
Q7002 6-552-936-01 TRANSISTOR DTC014EUBTL FFC6 1-972-244-11 FLEXIBLE FLAT CABLE (7P) (L = 240 mm) (Silver)
(See Note)
< SWITCH > 0 M1 1-855-006-41 FAN, DC
MIC1 1-852-158-11 MICROPHONE, ELECTRET CAP
S7000 1-762-875-21 SWITCH, KEYBOARD (1) 0 OP1 A-2046-956-A OPTICAL PICK-UP BLOCK (CMS-S76RFS7G) (SV)
S7001 1-762-875-21 SWITCH, KEYBOARD (x) (Including Sled motor, Spindle motor, Sheet)
S7002 1-762-875-21 SWITCH, KEYBOARD (N)
S7003 1-762-875-21 SWITCH, KEYBOARD ( ) SP1 1-859-278-11 LOUDSPEAKER (69 mm) (Midrange: L-ch)
S7004 1-762-875-21 SWITCH, KEYBOARD (KARAOKE) SP2 1-859-277-12 LOUDSPEAKER (34 mm) (Tweeter: L-ch)
SP3 1-859-278-11 LOUDSPEAKER (69 mm) (Midrange: R-ch)
S7005 1-762-875-21 SWITCH, KEYBOARD ( PAIRING BLUETOOTH) SP4 1-859-277-12 LOUDSPEAKER (34 mm) (Tweeter: R-ch)
S7006 1-762-875-21 SWITCH, KEYBOARD (– VOLUME) SP5 1-859-276-11 LOUDSPEAKER (260 mm) (Subwoofer)
S7007 1-762-875-21 SWITCH, KEYBOARD (MEGA BASS) *************************************************************
S7008 1-762-875-21 SWITCH, KEYBOARD (– )
S7009 1-762-875-21 SWITCH, KEYBOARD (PARTY CHAIN) ACCESSORIES
************
S7010 1-762-875-21 SWITCH, KEYBOARD (MIC/GUITAR LEVEL –)
S7011 1-762-875-21 SWITCH, KEYBOARD (PARTY LIGHT) 4-729-484-13 MANUAL, INSTRUCTION (Operating Instructions)
S7012 1-762-875-21 SWITCH, KEYBOARD (VOCAL FADER) (ENGLISH) (UK, AUS, E4, E93, SP, IND, LA)
S7013 1-762-875-21 SWITCH, KEYBOARD (SOUND FIELD) 4-729-484-23 MANUAL, INSTRUCTION (Operating Instructions)
S7014 1-762-875-21 SWITCH, KEYBOARD (VOICE CHANGER) (SPANISH) (AR, LA)
4-729-484-32 MANUAL, INSTRUCTION (Operating Instructions)
S7015 1-762-875-21 SWITCH, KEYBOARD (FIESTA) (FRENCH) (AEP, E4, E93)
S7016 1-762-875-21 SWITCH, KEYBOARD (MIC ECHO) 4-729-484-42 MANUAL, INSTRUCTION (Operating Instructions)
S7017 1-762-875-21 SWITCH, KEYBOARD (W.PARTY CHAIN) (GERMAN) (AEP)
S7018 1-762-875-21 SWITCH, KEYBOARD (GUITAR) 4-729-484-52 MANUAL, INSTRUCTION (Operating Instructions)
S7019 1-762-875-21 SWITCH, KEYBOARD (FUNCTION) (DUTCH) (AEP)
S7020 1-762-875-21 SWITCH, KEYBOARD (MIC/GUITAR LEVEL +) Note: Since Ref. No. FFC3 and Ref. No. FFC6 have the same number
S7021 1-762-875-21 SWITCH, KEYBOARD ( +) of cores, be careful not to mistake the connectors to be connected
S7022 1-762-875-21 SWITCH, KEYBOARD (GESTURE ON/OFF) absolutely. If it connect them to the wrong connector, this unit is
S7023 1-762-875-21 SWITCH, KEYBOARD (VOLUME +) damaged.
S7024 1-762-875-21 SWITCH, KEYBOARD (PLAYBACK) Be sure to check the color of flexible flat cable, before connecting
the Ref. No. FFC3 or Ref. No. FFC6 to the connector.
Refer to “2-3. TOP PANEL BLOCK-1” on page 11 for connection
location.
71
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
Ver. 1.2
Ref. No. Part No. Description Remark

(ITALIAN) (AEP)
(POLISH) (AEP)
(RUSSIAN) (RU)
(UKRAINIAN) (RU)
(PORTUGUESE) (E4)

(ARABIC) (E4, E93)
(TRADITIONAL CHINESE) (SP)
(MALAYSIAN) (SP)
(THAI) (TH)
(SPANISH) (AEP)

(PORTUGUESE) (BR)
501 1-493-448-11 REMOTE COMMANDER (RMT-AM420U)

(Remote control)
502 1-754-852-11 ANTENNA (FM) (FM lead antenna)
0 503 1-785-504-21 ADAPTOR, CONVERSION (AC plug adaptor)
(E4, SP, LA)
0 504 1-846-426-52 CORD SET, POWER-SUPPLY
(AC power cord (mains lead)) (AR)
0 504 1-846-427-52 CORD SET, POWER-SUPPLY
(AC power cord (mains lead)) (BR)
0 504 1-912-312-51 POWER SUPPLY CORD SET

(AC power cord (mains lead)) (E4, LA)
(AC power cord (mains lead)) (E93)
(AC power cord (mains lead)) (TH)
(AC power cord (mains lead)) (IND)
0 504 1-912-499-21 POWER-SUPPLY CORD WITH FILTER
(AC power cord (mains lead)) (AEP, RU, SP)

(AC power cord (mains lead)) (AUS)
(AC power cord (mains lead)) (UK)
501 502
Remote control (1) FM lead antenna (1)
(E4, SP, LA)

503
AC plug adaptor (1)
504
AC power cord (mains lead) (1)
72
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
MEMO
73
SYS SET
2023/02/25 06:36:40 (GMT+09:00)
MHC-V41D
REVISION HISTORY
Ver. Date Description of Revision

1.0 2018.02 New
1.1 2018.04 Addition of RU, E4, E93, BR, SP, AR, TH and IND models
Change of SMPS board (Suffix-12)
Change of Part No. for TOP PANEL (Ref. No. 55) (SMR-17049)
1.2 2019.03 Change of “Protect Type Description”

Addition of Note for Connection of Flexible Flat Cable (7P)
Change of MOTHER board
Deletion of Part for Ref. No. CN113 on the MOTHER board (Former MB type)
Change of Description for Ref. No. Q7707 and Q7708 on the MIC board
Change of Description for Ref. No. Q7002 on the PANEL board
Change of Description for Ref. No. Q6500, Q6506 and Q6507 on the SMPS board
Change of Part No. for RUBBER FOOT (Ref. No. 252), CDM90 ASSY (Ref. No. CDM1) and
LOUDSPEAKER (34 mm) (Ref. No. SP2 and SP4)
Addition of Part No. for IR WINDOW (Ref. No. 256)
Change of Part No. for POWER SUPPLY CORD SET (E93) (SMR-18040)
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.
e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.
SYS SET

HCD V41D

Uploaded by

Copyright:

Available Formats

HCD V41D

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HCD V41D

Uploaded by

Copyright:

Available Formats

2023/02/25 06:36:40 (GMT+09:00)

Model Name Using Similar Mechanism MHC-V44D/V50D

HOME AUDIO SYSTEM

License and Trademark Notice t Android and Google Play are

For customers in Europe

NOTES ON CHIP COMPONENT REPLACEMENT

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

1. SERVICING NOTES ............................................. 4 6. DIAGRAMS

5. TROUBLESHOOTING .......................................... 38 8. ELECTRICAL PARTS LIST .............................. 70

Accessories are given in the last of the electrical parts list.

Note: The MOTHER board has been changed in the midway of

IMPORTANT NOTE OF PERFORMING THE OPERA-

: LEAD FREE MARK

CAPACITOR ELECTRICAL DISCHARGE PROCESSING MODEL IDENTIFICATION

Perform the discharge

Perform the discharge processing 800 :/2 W

IMPORTANT 4. Press the [ +]/[– ] buttons to select target destination, and

Setting destination by display:

– Continued to the upper right –

CHECKING THE OPERATION AFTER REPAIR SPREADING OF COMPOUND

NOTE OF REPLACING THE ELECTRICAL PARTS ON – MOTHER Board (Side A) –

NOTE OF REPLACING THE MOTHER BOARD FOR

2 Pull out the tray in the

CHANGE OF MOTHER BOARD

– MOTHER Board – MOTHER Board Serial number

Serial number location

2-1. DISASSEMBLY FLOW

2-3. TOP PANEL BLOCK-1

2-4. TOP PANEL BLOCK-2

2-17. PANEL BOARD 2-18. ELECTRET CAP MICROPHONE

2-19. NFC BOARD 2-20. GESTURE BOARD

2-12. DC FAN, 2-21. FRONT PANEL BLOCK-1 2-15. MOTHER BOARD

2-22. FRONT PANEL BLOCK-2 2-24. LOUDSPEAKER (TWEETER)

2-23. SW LED BOARD, 2-25. LOUDSPEAKER (MIDRANGE)

2-28. TOP PANEL BLOCK SERVICE POSITION

Note: Follow the disassembly procedure in the numerical order given.

2-2. SIDE PANEL

1 two screws 3 claw

4 side panel (L)

front side 4 side panel (R)

1 Cut the insulock tie.

0 flexible flat cable (7P) [white] (CN120)

5 microphone wire connector

The opposite side

2-4. TOP PANEL BLOCK-2

(AEP, RU, UK,

3 Lift up rear side of the top

top panel block

7 top panel block

(AEP, RU, UK,

6 PANEL board cable

2-5. LOADING PANEL BLOCK

DVD mechanism deck top side

rear side DVD mechanism deck

4 Remove the loading

1 Insert the clip etc. in the hole, and

Note about installing the loading panel block

2-6. LOADING PANEL

Note about installing the loading panel block

'&IDQFDEOHVHWWLQJ boss 4 Remove the DC fan cable

3 MOTHER board cable :LUHVHWWLQJ

boss )OH[LEOHIODWFDEOHVHWWLQJ Pass the flexible flat cable

1 screw 3DVWLQJSRVLWLRQRIWKHILODPHQWWDSHVXEPDWHULDO