Bias - TS

Bias-T Design Considerations for the LWA
Brian Hicks and Bill Erickson May 21, 2008

The strawman design document [1] for the LWA suggests that the Front End Electronics (FEE) could be powered through the use of a circuit known as a bias-T. We will discuss how a bias-T operates and present a low cost design optimized for performance within the LWA frequency range of 20 to 80 MHz. We highly recommend the use of bias-T based on discrete components incorporated directly into the LWA FEE and ARX subsystems.
I. Introduction
A bias-T is a three port network designed to provide power to remote devices, such as amplifiers, over the same coaxial cable that RF signals are conveyed. The basic topology, and means of operation, of a bias-T network suitable for LWA applications is given in Figure 1.
Capacitor Passes RF and Blocks DC and Low Frequency (60 Hz) AC RF ONLY C1 Shunt Capacitor Routes any remaining RF leakage to Ground, Increasing Isolation between RF Ports and DC Supply Port. C2 DC Power Supply L1 RF + Power Inductor Blocks RF and Passes DC and Low Frequency (60 Hz) AC
Figure 1 Basic Inductive Bias-T
Commercially available bias-Ts are available in both connectorized and surface mount versions. These units are typically expensive ($40 to $100) and, although designed to be wideband, often suffer in performance at frequencies below 50 MHz. By concentrating on an LWA specific bias-T we can achieve a significant cost savings. We will focus on presenting a bias-T circuit that is optimized for operation below 100 MHz and has the ability to supply a single polarization of an LWA FEE (230 mA). We will also deliver a circuit with a compact printed circuit board (PCB) footprint.
II. LWA Bias-T Design Considerations

Consisting of one inductor and one capacitor the bias-T circuit is simple, but particular consideration must be given to component selection. Although not a part of the generic bias-T circuit, the shunt capacitor (C2) on the DC port should not be considered optional (Figure 1). Addition of this capacitance substantially increases isolation between the RF ports and the DC supply connection by routing any remaining RF leakage on the supply side of the inductor to ground (Figures 11, 12, and 13). It is especially important that the inductor be rated for the necessary current and should optimally have a minimum self resonant frequency (SRF) that is above the highest LWA frequencies. Throughout the entire LWA band, the inductor must present high impedance, and both capacitors must present low impedance; resonances must be avoided. Based on research and experience, we have selected the following components for consideration and testing:
Capacitors (C1, C2): Inductor (L1): 0.1 F Ceramic Capacitor (SMT 1208), Panasonic, ECJ-3VB1E104K 4.7 H Wirewound Inductor (SMT 1008), Delevan, 1008-472J
III. LWA Bias-T Prototyping

We have produced a PCB layout to enable us to reliably evaluate the performance of our bias-T with a variety of components (Figure 2). The SMA connectors featured here are only included as a convenience for testing. The basic orthogonal arrangement of L1 and C1 can be readily incorporated into the FEE and ARX regardless of the connectors these subsystems utilize.
Figure 2 Bias-T Evaluation Board
The circuit was evaluated both as a single unit and in the intended configuration with two bias-Ts connected together and transferring power. In the configurations with two biasTs, we supplied 15 VDC at ~240 mA to a power-resistor load (~3.6 Watts dissipated) throughout the test (Figure 3). It was our intention to evaluate the performance of the inductors in the circuit while operating under load conditions representative of a G250R balun (FEE).
Figure 3 Characterization of the Bias-T Operating under Load
In the single unit configurations we placed an SMA short on the DC port of the bias-T. It was our intention here to capture the performance of the single bias-T when connected to a DC power supply with very low output impedance. An Agilent N3383A vector network analyzer was used to characterize insertion loss (S21), return loss (S11 and S22), and isolation (S21 between RF and DC ports). A complete set of data is included in the measurements section of this report.
IV. Observations and Recommendations

The performance of the bias-T presented here is comparable to designs that we have already fielded and found to be entirely successful in operation. Within the LWA band, the performance of this circuit compares favorably to costly commercial units. The insertion loss of two of these cascaded bias-Ts was found to be less than 0.2 dB, and the aggregate return loss was found to be least -20 dB. RF coupling from one dipole to another through the DC power network is a serious concern and potential source of indirect mutual coupling. It is important that significant attenuation be presented between the RF ports and the DC supply node of the bias-T. Direct mutual coupling between elements at a spacing of 4m has been demonstrated to be approximately -20 dB, declining ~5 dB for each 2m increase in spacing [2]. After 20 meters the mutual coupling between elements is approximately -60 dB and only gradually diminishes with additional spacing [2]. Consequently, we recommend that feed system coupling be kept well below -80 dB. The most expedient means of accomplishing this goal is the introduction of a capacitive shunt on the DC side of the bias-T. This can be seen on the schematic (Figure 14) as capacitor C2. It is typically a part of good engineering practice to incorporate bypass capacitors (such as C2) at DC supply nodes; we provide measurements here to emphasize the consequences of omitting this component. The isolation between the RF port and DC port of the bias-T without the capacitive shunt is seen to be inadequate in Figure 11. A definite improvement in isolation is seen when a 0.1 F shunt is added at
the DC supply node (Figure 12). With the shunt, at least 60 dB of attenuation between the RF ports and the DC supply port is achieved. An RF signal must run the gauntlet of two of networks consisting of L1 and C2 to traverse the DC feed ports of two bias-Ts and get from one dipole signal chain to another. Greater than 100 dB of attenuation is observed in this configuration (Figure 13). The prototype circuit fits within an 8.3 x 10 mm square on the circuit board; PCB space constraints should not be problematic. We recommend the use of a high-capacity DC power supply to supply power to the FEEs via a bias-T arrangement such as discussed here. This method of power distribution will spare the cost of installing and maintaining a separate power distribution network and eliminate unnecessary complexity in station installations. Because DC power is sourced via the center conductor of shielded coaxial cable, the resulting power network is effectively shielded at no additional cost. Candidate connectors for LWA RF cabling will likely incorporate conductive backshells which will act to further inhibit the introduction of RFI via the power distribution network. By incorporating a bias-T into the ARX, the option of allowing power to the antenna stands to be under control of the LWA Monitor and Control System (MCS) becomes inexpensive and straightforward to implement. This feature could prove valuable for diagnostics, maintenance, and station commissioning.
V. Summary Table Operating Frequency Isolation Insertion Loss VSWR Maximum DC Voltage Maximum DC Current Size Parts Cost 15 to 115 MHz 60 dB Minimum 0.2 dB Maximum 1.2:1 Maximum 25 VDC 334 mA PCB Footprint Approximately 8.3 x 10 mm $0.92
VI. Measurements: -30 dBm Power Level for RF Stimulus

1. Measurements of a Single Bias-T
Figure 4 Insertion Loss (S21) through a Single Bias-T with DC Port Shorted
Figure 5 Return Loss (S11 and S22) into a Single Bias-T with DC Port Shorted
Figure 6 Return Loss (S11 and S22) into a Single Bias-T with DC Port Shorted (Smith)
2. Measurements of a Two Bias-Ts in Cascade Delivering 240 mA to a Load
Figure 7 Insertion Loss through Two Bias-T Supplying 240 mA to a Resistive Load
Figure 8 Return Loss (S11 and S22) into Two Cascaded Bias-Ts Delivering 240 mA
Figure 9 Return Loss (S11 and S22) into Two Cascaded Bias-Ts Delivering 240 mA (Smith)
Figure 10 SWR (S11 and S22) into Two Cascaded Bias-Ts Delivering 240 mA
Figure 11 Single Bias-T Isolation between RF and DC Port without Capacitive Shunt. RF+DC Port 50 Terminated
Figure 12 Single Bias-T - Isolation between RF and DC Port with Capacitive Shunt (0.1 F). RF+DC Port 50 Terminated
Figure 13 Two Bias-Ts - Isolation between RF and RF Port with Capacitive Shunts (0.1 F). RF ports 50 Terminated. Note: A power level of 0 dBm was used for this measurement.
VII. Bill of Materials

Designation C1, C2 L1 Value 0.1 F 4.7 H Tolerance Type 10% +/- 5% Capacitor, Ceramic Inductor, Unshielded (1206), X7R Manufacturer Cost Part No. Panasonic $0.056 ECJ-3VB1E104K (Quantities > 4000) $0.81 Delevan 1008-472J (Quantities > 2000)
Total cost for each bias-T: $0.92 Total cost each antenna stand (4 bias-Ts, two per polarization): $3.69 The results presented here are based on the use of Delevan part 1008-472J for L1. Alternatively, part WW1008-472R could also be used. The former part is less expensive, and more readily available. Specifications for both parts are provided in the datasheet section at the end of this report.
VIII. References
[1] A Strawman Design for the Long Wavelength Array Stations, P.S. Ray (et. Al), April 11, 2006, http://www.ece.vt.edu/swe/lwa/memo/lwa0035.pdf, LWA Memo #35. [2] Report on Mutual Coupling and Impedance Measurements on Large Blade Dipoles, B. Erickson, H. Schmitt, E. Polisensky, August 28, 2006, http://www.ece.vt.edu/swe/lwa/memo/lwa0053.pdf, LWA Memo #53.
10
IX. Schematics and Layouts
Figure 14 Bias-T Schematic
11
IX. Schematics and Layouts (Continued)
Figure 15 Bias-T Evaluation PCB Note: Active portion of circuit fits within an 8 x 10 mm rectangle.
12
X. Datasheets (L1 and C1)
13
14
15
16

Bias - TS

Uploaded by

Copyright:

Available Formats

Bias - TS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bias - TS

Uploaded by

Copyright:

Available Formats

Bias-T Design Considerations for the LWA

Brian Hicks and Bill Erickson May 21, 2008

Figure 1 Basic Inductive Bias-T

II. LWA Bias-T Design Considerations

III. LWA Bias-T Prototyping

Figure 2 Bias-T Evaluation Board

Figure 3 Characterization of the Bias-T Operating under Load

IV. Observations and Recommendations

VI. Measurements: -30 dBm Power Level for RF Stimulus

2. Measurements of a Two Bias-Ts in Cascade Delivering 240 mA to a Load

VII. Bill of Materials

IX. Schematics and Layouts

Figure 14 Bias-T Schematic

IX. Schematics and Layouts (Continued)

X. Datasheets (L1 and C1)

You might also like