1003003951

1
Operation and Maintenance Manual
PowerKit 4M06 Series Diesel Engine

4M06CR (2-valves)
4M06MP (2-valves)
Foreword

Foreword
Please be advised, do not operate or per- Safety
form any operation, maintenance, or repair The Safety section of this manual covers
on this PowerKit engine until you have read basic safety precautions and shows warn-
and understood the information in this ings and potentially hazardous situations.
Manual in its entirety. This Manual must be This Manual must be read in full before op-
read in full before operating your PowerKit in erating your PowerKit in order to operate
order to gain the maximum operational per- and maintain the engine safely.
formance of the engine and to safely operate
and maintain the engine. The operation and
Maintenance & Spare Parts
maintenance instructions are given as a
Maintenance should be carried out at the
guide for engines operating at the rating as
appropriate intervals as shown in the
sold.
Maintenance Table. The inspection and
maintenance intervals are given as a guide,
Documentation
for engines operating under normal condi-
Baudouin uses English as the primary tions. Consult with your Baudouin repre-
business language for all publications. Other sentative for operation under severe condi-
languages may be available, please consult tions.
with your local Baudouin representative.

We recommend that a copy of the Mainte-

The photos and illustrations in this manual nance Schedule be displayed near the en-
are for reference only. Some illustrations gine and that a service record be kept and
may have been modified to ensure clarity stored with the engine.
(for example guards and covers may be
removed), and some equipment shown in The use of Baudouin Genuine Spare Parts is
this manual may be different to your engine. imperative to the optimal operation, perfor-
For the latest information, please contact mance and longevity of your PowerKit en-
your local Baudouin representative. gine. The use of alternatives or counterfeit
parts can lead to voiding engine warranty，
The 'DT' technical documents ('documenta- damage, failures, and personal injury or
tion technique') quoted in this Manual are death.
available from the Baudouin Network for
reference.
Overhaul
This Manual does not include detailed in-
The information contained in this Manual is
structions for overhaul of your engine. Con-
correct at the time of publication. Baudouin
tact your local Baudouin representative who
reserves the right to modify these specifica-
can help you to proceed with an overhaul
tions without notice.
program for your engine. All major repairs
should be carried out by an authorized
Baudouin partner.
 Content

Foreword .............................................................................................................................. 2
1. Safety ............................................................................................................................... 1
1.1 Safety Information ........................................................................................................ 1
1.2 Symbols Used .............................................................................................................. 2
1.4 Environmental Safety ................................................................................................... 5
1.5 Fluid Safety .................................................................................................................. 6
1.6 Batteries ....................................................................................................................... 6
1.7 Welding......................................................................................................................... 7
1.8 Electrical Risks ............................................................................................................. 8
1.9 Lines, Tubes and Hoses ............................................................................................... 9
1.10 Coolant Safety ............................................................................................................ 9
1.11 Cleaning the Engine ................................................................................................. 10
1.12 General Precautions for Operation ........................................................................... 11
1.13 Recommendations for Engines Equipped with Common Rail System .................... 13
2. Product........................................................................................................................... 14
2.1 Rating Definitions ....................................................................................................... 14
2.2 Engine Model Definition ............................................................................................. 15
2.3 Engine Overview ........................................................................................................ 18
2.4 Cooling Circuits .......................................................................................................... 20
2.5 Lubrication System ..................................................................................................... 22
2.6 Fuel System ............................................................................................................... 23
2.7 Electronic Control Unit (ECU) .................................................................................... 25
2.8 Electronic Governor System for Mechanical Pump Engine ....................................... 31
3. Installation ...................................................................................................................... 33
3.1 Engine Lifting .............................................................................................................. 34
3.2 Engine Mounting ........................................................................................................ 36
3.3 Accessories ................................................................................................................ 38
3.4 Air Intake System ....................................................................................................... 39
3.5 Exhaust System ......................................................................................................... 39
3.6 Cooling System .......................................................................................................... 39
3.7 Lubrication System ..................................................................................................... 40
3.8 Fuel System ............................................................................................................... 40
3.9 Engine Control System............................................................................................... 41
3.10 Electrical Components ............................................................................................. 43
3.11 Installation and debugging of Electronic Governor System ..................................... 44
3.12 Genset Installation Recommendations .................................................................... 44
4. Operation ....................................................................................................................... 51
4.1 Preparations before Start ........................................................................................... 52
4.2 Starting Up ................................................................................................................. 53
4.3 Operation of the PowerKit Engine .............................................................................. 54
4.4 Precautions for running in cold environments ............................................................ 55
4.5 Stopping the PowerKit Engine ................................................................................... 56
4.6 Electronic control system ........................................................................................... 57
5. Maintenance .................................................................................................................. 58
Content

5.1 General Safety Conditions for Maintenance .............................................................. 58

5.2 Maintenance Table ..................................................................................................... 59
5.3 Maintenance Operation .............................................................................................. 61
5.4 Storage Protection Instruction .................................................................................... 82
6. Appendix ........................................................................................................................ 89
6.1 Coolant Recommendation .......................................................................................... 89
6.2 Lubricant Recommendation ....................................................................................... 90
6.3 Fuel Recommendation ............................................................................................... 92
6.4 Common Faults and Troubleshooting ........................................................................ 93
6.5 Recommended Torques for Bolts ............................................................................. 143
Index ................................................................................................................................ 145
 Safety

1. Safety
1.1 Safety Information

Failure to comply with the preventive measures and safety instructions included in this manual
and with warnings indicated on the engine may lead to injury or death. This Operation and
Maintenance Manual must be kept on or near the engine and must be easily accessible and
ready to be consulted at any time. Furthermore, this manual must stay with the engine at all
times.

Most accidents can be prevented by following basic safety precautions, recognizing hazardous
situations and acting accordingly, but these safety instructions alone are not sufficient to avoid
every hazard. Baudouin cannot anticipate or identify every possible hazard in your operating
environment. Persons operating or maintaining the engine must be able to recognize haz-
ardous situations, and they must have the necessary skills, training and tools to perform op-
eration and maintenance activities properly.

1
 Safety

1.2 Symbols Used

Please take note of the warnings and precautions indicated throughout this Manual in order to
avoid unsafe practices and conditions. In this Manual, the following symbols are used to high-
light specific information.

HAZARD WARNING
This warning symbol is recognized across
the world. In this Manual this symbol is used
to highlight the importance of the information
that follows. Make sure that you understand
the consequences of a dangerous situation
and the ways in which to avoid danger.
Failure to comply with warnings can result in
material damage, serious injury or even
death.

WARNING
This type of warning indicates a potentially
dangerous situation, which if not avoided,
may result in serious injury, death, or con-
siderable material damage.

CAUTION
This type of warning indicates a potentially
dangerous situation, which if not avoided,
may result in minor injury or material dam-
age. It can also warn against dangerous
practices.

The warnings in this guide cannot cover every situation imaginable. Please only use proce-
dures, methods, tools, and parts specially recommended by the engine manufacturer.

2
 Safety

Safety symbols
Symbol Definition

Wear hand protection

Wear ear protection

Wear eye protection

Wear head protection

Wear foot protection

Wear a protective mask

Wear overalls

Avoid naked flames

Do not smoke

Do not use a mobile phone

Keep an extinguisher close by

Danger: battery acid

Danger: live cables, electrical risks

Highly flammable products

Keep away from hanging loads

Risk of thermal burns

Risk of mechanical drive / rotating parts

Lifting is forbidden

Risk of steam burns

Water drain valve

3
Safety

Universal Warning
The location of the Universal Warning label is illustrated below.

 4M06 Series

Figure 1.2A-4M06 Illustration

Do not operate or perform maintenance on this engine

unless you have read and understand the instructions
and warnings in this Operation and Maintenance Manual.
Failure to follow the instructions or heed the warnings
could result in serious injury or death.

4
 Safety

1.3 Personal Safety

These Personal Safety precautions are designed to reduce the risk of contamination, serious
injury or death.
 Wear personal protective equipment (PPE) as required.
 Avoid prolonged and repeated contact with oil and diesel fuel.
 Do not put oily rags in pockets.
 Avoid contaminating clothing with oil.
 Wash overalls regularly. Throw away unwashable clothing and shoes impregnated with
oil.
 Emergency treatment must be immediately sought in the event of any injury.
 Always wear protective mechanic's gloves before working in order to avoid prolonged and
repeated contact with oil and diesel fuel.
 Wash with soap and hot water or, alternatively, use hand detergent and a nailbrush to
make sure that all oil is removed. Products containing lanolin can help replace the skin's
natural oils that may have been removed.
 DO NOT use petrol, kerosene, fuel, thinners or solvents to clean the skin.
 If skin problems occur, immediately consult a doctor.
 If possible, degrease components before handling them.
 When there are risks for the eyes, use safety glasses or a face shield. An eye-rinsing
solution must be kept close at hand.
 Do not spill oil or other fluids on the ground when repairing the engine. In the event of an
accidental spillage of hydrocarbon or other fluid, take all the necessary measures to
section off the area, clean up and protect people and the environment.
 The handling, storage and recycling of hydrocarbons, ethylene, glycol and oil must
comply with the safety and environmental standards applicable in the country where
these operations take place.
 Ensure that all guards and covers are secured in place on the engine.
 Make sure adequate, non-expired extinguishers are available and that personal are
adaquately trained in extinguisher operation.

1.4 Environmental Safety

 There are laws regarding environmental protection and the disposal of waste of
hydrocarbons. To ensure compliance with environmental protection laws, consult your
local authorities who will advise you. Obey all local regulations for the handling and
disposal of liquids.
 The products and spare parts supplied by Baudouin do not contain asbestos.

5
Safety

1.5 Fluid Safety

 All oil, fuel, and some coolant liquids

are flammable. If these liquids are
leaking onto hot surfaces they can
cause a fire which can cause injury
and/or damage.
 Do not check for leaks using any body
part. Use a cardboard section or other
appropriate tool to check for a leak.
 Store all fuels and lubricants in closed,
clearly labelled containers in a safe
place.
 When draining liquids from the engine,
ensure that the correct tools are used
and that liquids are collected in a suita-
ble container and disposed of following
all local regulations.
 Oily rags and other flammable materials
must not be stored in close proximity to
engine, genset, or system.
 Do not smoke near the fuel tank or
while in the filling area. Ensure there
are no open flames or sparks. Always
stop the engine before refuelling.
 Mobile phones (in particular their bat-
teries) may give off sparks that could
cause an explosion in certain high-risk
areas. Switch off all mobile phones
when filling the fuel tank or while in the
filling area.

1.6 Batteries

 Wear personal protective equipment

(PPE) as required.
 Do not smoke in areas where batteries
are charged or near fuel circuits.
 The batteries release flammable fumes
that can explode. Ensure there are no
open flames or sparks near the battery.
 If the batteries are in a closed area,
make sure there is sufficient ventilation.
6
 Safety

 The battery cables must be fitted with a

battery switch and fuse or circuit
breaker to isolate the circuit.
 Sulphuric acid contained in batteries is
toxic and corrosive; it can burn clothes
and skin or even cause blindness in
case of contact with the eyes.
 Disconnect the batteries before any
operation involving the electrical sys-
tem.
 Never disconnect any battery cable
while the engine is operating.
 Never check battery charge by short
circuiting it.
 Do not charge a frozen battery; heat it
up 16°C (61°F) beforehand.
 In the event of corrosive material con-
tact with a body part:
 Rinse the affected part with plenty
of water.
 Apply bicarbonate of soda or lime
to neutralise the acid.
 Rinse your eyes for 10 to 15
minutes.
 See a doctor immediately.
 In the event of ingestion see a doctor
immediately.
 Make sure the batteries are clean and
fitted with the recommended covers,
cables and connections.
 Electric wiring must be kept in good
condition, properly positioned and at-
tached.

1.7 Welding

 Do not weld or flame cut pipes, hoses

or tanks that contain flammable fluids.
Components containing flammable flu-
ids must be drained and cleaned ap-
propriately with a non-flammable sol-
vent before conducting any welding of
flame cutting.
 Disconnect the engine wiring harness
7
Safety

before welding (control cabinets, elec-

trical cabinets etc.).
 Comply with all legal provisions in force
before conducting welding work.
 Do not use open fires.
 Make sure that the work will not affect
the on-board electrical and electronic
equipment.
 Make sure that the automatic fire sup-
pression system is deactivated before
any welding or grinding work.
 Make sure that there is sufficient venti-
lation in the premises where welding is
to be carried out.

1.8 Electrical Risks

 Electrical checks must be carried out

regularly.
 Electric wiring must be kept in good
condition, properly positioned and
soundly attached.
 All wires should be of the recommend-
ed size.
 Wires and cables must be protected by
a fuse or calibrated circuit breaker.
 Do not short-circuit fuses and/or circuit
breakers.
 The electrical circuit of the engine must
be isolated from the engine and gener-
ator.
 Ensure that the engine is grounded
correctly to prevent uncontrolled elec-
trical circuit paths which can cause
damage.
 Insulation problems can cause short-
circuits or stray current. Stray current
can damage electrical and electronic
components, bushing or crankshaft
seating and may also cause ra-
dio-frequency disturbance.
 The engine earth must be properly con-
nected to the chassis, as well as all the
flexible hoses.
8
 Safety

 Flexible connections for cooling

 Flexible circuit connections fuel
 Electrical control systems and
electronic fuel injection
 Earth faults can cause corrosion in the
pipes and engine or genset unit compo-
nents.

1.9 Lines, Tubes and Hoses

 Ensure that all high pressure lines are

not bent, worn or damaged. High pres-
sure lines must be positioned, sup-
ported and firmly fastened. Do not at-
tach any other components to the high
pressure lines. Tighten all connections
to the recommended torque.
 Do not check for leaks using your hand.
Use a cardboard to check for a leak.
 Tighten all connections and filter hous-
ings to the recommended torque.
 Release the lubrication, fuel and pres-
sure cooling circuits before discon-
necting or removing hoses or associ-
ated parts.

1.10 Coolant Safety

 At operating temperature, the coolant is

hot and pressurized. When pressure is
released sharply, this hot liquid may be
transformed into fumes. Any contact
with this hot liquid or these fumes may
cause serious burns.
 The cooling system also contains alkali
which can cause injury. Do not allow
alkali to contact your skin, eyes or
mouth.
 Let the components of the coolant cir-
cuit cool down before draining the cir-
cuit.
 Only check the coolant level when the
engine has stopped.
9
Safety

 Slowly unscrew the coolant filler plug to

release pressure.

1.11 Cleaning the Engine

 Use personal protective equipment

when cleaning an engine.
 Regularly clean the engine surface to
remove any greasy deposits that may
be flammable.
 Do not wash an engine in operation or
which has just stopped.
 Use the safety equipment required by
your local codes and standards.
 Make sure high-pressure water cannot
damage the equipment being washed.
Do not get electrical equipment or seals
wet.
 Take necessary precautions when us-
ing a high-pressure cleaner. Comply
with the safety instructions indicated for
the cleaning equipment used as well as
local codes and standards.
 High pressure cleaning can blow out
high-speed debris from the engine
which can cause injury.

10
 Safety

1.12 General Precautions for Operation

1.12.1 Before any operation or maintenance on any Baudouin product

 Wear personal protective equipment (PPE) where required.

 For maintenance, place a “Do Not Use” or similar sign on the starter switches.
 Access to the equipment is only for authorized and qualified personnel.
 Ensure that all guards and covers are secured in place on the engine.
 Make sure that the repair premises and surrounding area are suitable for safe working.
 Inspect the engine for potential hazards. Ensure there are no personnel on, under or
around the engine.
 Ensure that the pipes and hoses are not worn or damaged. Pipes must be positioned,
supported and firmly fastened.
 Ensure that the electrical wiring is not worn or damaged. Wiring must be positioned,
supported and firmly fastened
 Remove all wiring that is obstructive to repair/maintenance or unattached.
 Use the proper tools for the operation being performed.
 Report all necessary repairs promptly.
 Remove any rings, chains and watches before starting work. Wear suitable and proper-
ly-fitting work clothes.
 Remove and isolate the control panel key.
 Do not perform any operation or maintenance operations which are not fully understood.
 Clear the engine of any flammable materials such as fuel, oil or debris.
 Do not smoke near the engine or where flammable materials are stored.
 Exhaust shields (if equipped) must be fitted correctly.
 Do not expose the engine or components to flames.
 Do not touch hot parts of an engine in operation or which has just been stopped.
 Ensure the starter battery insulation switch is in open position.
 Switch off the circuit breaker located in engine connection box (if equipped).
 Switch off engine room lock switch or emergency stop (if equipped).
 For maintenance, for engines fitted with a pneumatic starter system, isolate the tanks and
evacuate the pipe linking the tanks to the starter.
 For engines installed on automatic start genset select the lock position on the selection
mode of the control panel, to avoid the engine start.
 Use caution when cover plates or other components are removed. Gradually loosen and
remove bolts/nuts but do not remove the last two bolts which are located on opposite
ends of the plate. Before removing the last two bolts, pry open the plate and gradually
release the pressure.
 Do not remove any hydraulic components or parts until the pressure in the system has
been relieved. Contact Baudouin for procedures required to remove hydraulic compo-
nents.

11
Safety

1.12.2 Starting the Engine

 For initial start-up of a new engine, or the first start after a service, make provisions to be
able to stop the engine if a fault occurs. This can be done by shutting off the fuel or air
supply to the engine.
 Never use any engine starting agents (for example, ether) to facilitate start-up due to a
risk of explosion or injury.
 Never start an engine without checking that this operation can be carried out without
danger to people or equipment. If there is a warning tag attached to the control panel or
start switch do not start the engine or touch the controls.
 Start the engine from the control panel or operator‟s booth.
 Ensure that the jacket water heater and/or lube oil heater (if equipped) are working
properly by checking the temperature gauges during the heating operation.
 Never short across the starting motor terminals or the batteries as this could damage the
electrical system.
 Never bypass or disable the automatic shutoff circuit – these are provided to help prevent
injury and engine damage.
 Engine exhaust could be harmful to your health, therefore always start and operate the
engine in a well ventilated area. If in an enclosed area, ensure the engine exhaust is
vented properly to the outside.

1.12.3 Stopping the Engine

 Stop the engine from the control panel or operator‟s booth.

 Use the Emergency Stop Button (if equipped) only in the event of an emergency. Do not
use the Emergency Stop Button for normal engine stopping. Do not start the engine after
using the Emergency Stop Button until the problem that caused the emergency stop has
been corrected.
 Let the engine cool down before carrying out any maintenance operation.
 Do not perform any operations on the engine for at least 15 minutes after an emergency
shut down.

12
 Safety

1.13 Recommendations for Engines Equipped with Common Rail System

 Wear personal protective equipment (PPE) where required.

 High-pressure fuel spray can cause irreversible body damage. Wear required protection
when conducting operations on the entire circuit.
 Make sure that the lines are depressurized before any dismantling operations.
 Release the high pressure before handling the feed and injection circuit of a common rail
engine.
 When checking the injectors, make sure that the high-pressure jet does not touch the
skin.
 All investigations of leaking fuel, oil or other high pressure liquids must be conducted us-
ing a screen and never with bare hands.
 Use a spray fumes extracting device.
 If fuel comes into contact with the skin, it can cause injury. Consult a doctor immediately.
 Fuel, oil and coolant contain harmful chemicals. Avoid any contact with skin and hands.

13
Product

2. Product
2.1 Rating Definitions

Rating definitions Running conditions

 Annual running time is unlimited.

COP
 Continuous rated power is allowed.
Continuous power
 No overload ability.

 Annual running time is unlimited.

 The average load rate is no more than 70% during a
PRP
range of 24 hours.
Unlimited Prime Rated Power
 Maximum time range with overload 10% within 12h
is 1 hour.

 The annual running time shall not exceed 200h.

 The average load rate shall not exceed 70% in 24h
cycle.
 No overload.
 The acceleration requirement is in accordance with
Q/WCG136.13. Acceleration from starting to rated
power should be within 10s without engine warm
stage.
 For natural aspirate diesel engine, when the envi-
ESP ronment temperature is below 5 degrees Celsius, it
Emergency Standby Power is need to use preheat facilities to warm coolant
temperature higher than 30 degrees Celsius. When
environment temperature is higher than 5degrees
Celsius, no preheating facilities are required.
 For diesel engine with turbocharger, when the en-
vironment temperature is below 10 degrees Celsius,
it is need to use preheat facilities to warm engine
coolant temperature higher than 30 degree Celsius.
When environment temperature is higher than 10
degree Celsius, no preheating facilities are required.

14
 Product

2.2 Engine Model Definition

The product model of Baudouin Industrial engines.

4 M 06 G 1 N 0 / 5

Speed Code
Oblique Line
Emission Stage Code
Fuel Code
Power Code
Application Code
Displacement per Cylinder
Product Code for Baudouin
Cylinder Number

2.2.1 Product Series Code

Product series Code is comprised by Cylinder Number、Product Code for Baudouin (M) and
Displacement per Cylinder.

2.2.2 Application Code

Code Application
G Land Power Generation
GT Land Power Generation for Tele com
V Variable speed models (Pump, Air pressure…)

2.2.3 Power Code

 Common rules
Use number 2, 4, 6…..as the different power lever for the models, choose 2 as the lowest
power and increase the power with the order of the number, 1, 3, 5, 7…..as the alternate
power code and will be used according to market demands.
 For the single speed engines that without emission (can only be used for PRP or
ESP)
Power code for 50Hz correspond Standby Power (kVA) of generating set.
Power code for 60Hz correspond Standby Power (kW) of generating set.
Contents of emission phase code and fuel code will not be used.

15
Product

2.2.4 Speed Code

RPM 1500 1800 1500 & 1800 3000

Code 5 6 S 3
Engine speed is only used for gen-set application using, and is shown as table, the speed
code for other application will not be used.

2.2.5 Emission Stage Codes

Emission Stage Code Non-road

0 No emission certification
U.S. EPA 40 CFR 60 JJJJ
1 U.S. EPA Tier 1
India CPCB I
U.S. EPA Tier 2
2
India CPCB Ⅱ
U.S. EPA Tier 3
3 EU Stage ⅢA/B
China stage Ⅲ
U.S. EPA Tier 4
India CPCB Ⅳ
4
EU Stage Ⅳ
China stage Ⅳ
5 EU stageⅤ
6 EU stage Ⅵ

Note1: New product model should be compiled on the basis of the most stringent Emission legislation；
Note2: Current model name can still be used when applying for another emission certification with
existing product.

2.2.6 Fuel Code

The fuel code of diesel oil is indicated by “D”，natural gas is indicated by “N”, and LPG is
indicated by “L”.

16
 Product

2.2.7 Engine Plate

 4M06 Series Diesel engine

Figure 2.2.1A-4M06MP

4M06MP: 4M06 with Mechanical Injection Pump

4M06CR: 4M06 with Common Rail Injection Pump

17
Product

2.3 Engine Overview

2.3.1 Schematic Diagrams of 4M06CR

1-Radiator
2-Fuel Pump
3- Intake Manifold
4-Air Filter
5-Fuel Filter
6-Flywheel housing
7-Oil Sump
8-Oil Cooler
9-Oil Filter

Figure 2.3.1A-Left Side

10-Exhaust Manifold
11-Turbocharger
12-Cylinder Head
Cover
13-Alternator
14-Fan
15-Starter

Figure 2.3.1B-Right Side

18
 Product

2.3.2 Schematic Diagrams of 4M06MP

1-Fan
2- Fuel Pump
3- Valve Cover
4- Air Filter
5- Flywheel Cover
6- Fuel Filter
7- Oil Inlet
8- Oil Filter
9- Oil Sump

Figure 2.3.2A-Left Side

10- Turbocharger
11-Thermostat
12-Water Pump
13-Alternator
14- Starter

Figure 2.3.2B-Right Side

19
Product

2.4 Cooling Circuits

2.4.1 Cooling Circuits for 4M06 Series Diesel Engine Overall Layout

1- Radiator
2- Cooled Coolant Inlet
Pipe
3- Thermostat assembly
4- Cylinder head group
5- Oil Cooler Inlet Pipe
6- Engine Block Inlet Pipe
7-Oil Cooler
8-Engine Block
9-Radiator Outlet Pipe
10-Coolant Pump

Figure 2.4.1A-4M06MP Overall Layout of cooling circuits

1- Radiator
2- Cooled Coolant Inlet
Pipe
3- Thermostat assembly
4- Cylinder head group
5- Engine Block Inlet Pipe
6-Oil Cooler
7- Oil Cooler Inlet Pipe
8-Engine Block
9-Radiator Outlet Pipe
10-Coolant Pump

Figure 2.4.2B-4m06 CR Overall Layout of cooling circuits

20
 Product

4M06 series diesel engine is equipped with 2 cooling circuits.

a) High temperature cooling circuit to cool:
 Cylinder block and cylinder head
 Engine oil through oil cooler
The internal circuit is designed for self-degassing.
To provide effective engine protection against freezing, chemical and galvanic corrosion,
cavitation and depositing, it is IMPERATIVE to use the recommended coolant as defined
in the 6.1 Coolant Recommendation. The high temperature coolant pump is located at
the engine‟s front side (See item 6 of the above picture).
b) Low temperature cooling circuit:
The low temperature cooling circuit cools the charged air (Air-to air cooled version).

21
Product

2.5 Lubrication System

4M06 Series engines are equipped with a lubrication system including an oil cooler.
The gear driving oil pump is located at the low front of the engine.
Many engine parts are lubricated by pressurized oil through piping and crankcase hoses.

 Oil circuit

1-Oil Dipstick 11-Camshaft Bearings

2-Suction Strainer 12-Main Bearing
3-Oil Pump 13-Conrod
4-Safety Valve 14-Rocker Arm Set
5-Oil Filter 15-Auxiliary Oil Gallery
6-Filter Bypass Valve 16-Piston Spray Nozzle
7-Oil Cooler 17-Intermediate Gear
8-Cooler Bypass Valve 18-Fuel Injection Pump
9-Main Oil Gallery 19- Turbocharger
10-Pressure Limiting 20-Oil Pan
Valve
Figure2.5A-Overall Layout of oil circuits

 Oil filters
4M06 Engine range is equipped with a lubricating system including 3 full flow oil filters
"Full flow" filters fitted in series on the circuit.
These cartridges are equipped with a by-pass valve allowing the continuity of the engine
lubrication even in case of a sudden clogging.

The engine oil from the oil pan passes through the oil suction strainer and then is pumped into
the oil filters and oil cooler by the oil pump, and finally arrives at the positions needed to be
lubricated through the oil line system. Most of the oil will come to the main bearings and then to
the connecting rod bearings via the oil gallery of crankshaft. The lubrication of cylinder liner
surface and piston pin is achieved through the lubricating oil injected by the piston cooling
nozzle. The valve control system, turbocharger, fuel injection pump and intermediate gear
bearing are also provided with forced lubrication via the oil pipe and oil gallery. The piston
head is cooled through injecting lubricating oil to the inner chamber of piston by the piston
cooling nozzle; and the lubricating oil is cooled by the cooling coolant in oil cooler. The pres-
sure of lubricating oil in the circulation system is regulated by the pressure limiting valves in the
oil pump body and main oil gallery.

22
 Product

2.6 Fuel System

2.6.1 Fuel circuit diagram of 4M06CR

The fuel pump draws the fuel from the genset fuel tank through pre-filter/water-separator and
through full flow filter to the injection pump.
Injection pump delivers fuel under high pressure to the injectors.
Excess fuel not injected is returned to the fuel tank.
Injector holder leakages return to fuel tank.

 Overall Layout of Fuel System

1-Tank with Pre-filter

2-Injection Pump
3-Fuel Filter
4-Injector
5-High-pressure Fuel Pipe
6-Fuel Return Pipe
7-Common Rail
8- High-pressure Fuel Pipe

Figure2.6.1A-Overall Layout of Fuel System

Low Pressure Circuit High Pressure Circuit Fuel Return Circuit

23
Product

2.6.2 Fuel circuit diagrams of 4M06MP

The feed pump draws the fuel from the genset tank through pre-filter/water-separator and
through full flow filter to the injection pump.
Injection pump delivers fuel under high pressure to the injectors.
Excess fuel not sprayed is returned to the fuel tank.
Injector holder leakages return to fuel tank.
.
 Overall Layout of Fuel System

1-Tank with pre-filter

2- Injection pump
3- Low Pressure Fuel Line
4- Fuel filter
5- Injector
6- High Pressure Fuel Line
7- Fuel Return Line

Figure2.6.2B-Overall Layout of Fuel System

Low Pressure Circuit High Pressure Circuit Fuel Return Circuit

24
 Product

2.7 Electronic Control Unit (ECU)

2.7.1 ECU for 4M06

The WISE15 ECU has two wire harness slots, in which the gray stands for the engine side and
the black stands for the genset control panel, each with 76 pins.
The engine wire harness includes engine sensors, fuel injectors and electrically controlled fan
pins, which have been installed before delivery.
The genset wire harness includes the functional pins of the genset, and OEM fabricates the
wire harness according to the functional needs of the genset.
Terminal diagram
WISE15-P160 Powerkit Terminal Diagram

BAT - BAT +
X1-02 X1-01 Battery
Battery - BAT - BAT + 25A +
X1-04 X1-03
BAT - BAT +
X1-06 X1-05 T15
CAN0H Key switch
Controller Area Network 0 X1-42 I_S_T15 Key switch 5A
X1-59
Communication & diagnose CAN0L
X1-43 I_S_T50 Start switch
120Ω in ECU X1-58
X1-44
Controller Area Network 1 CAN1H X1-68 I_S_SPAPOS
X1-45 Speed Adjustment（+）Low power relay of ECU，Do
Flash & calibration CAN1L X1-46
120Ω in ECU X1-51 I_S_SPANEG Speed Adjustment（-） not share with other loads
5V_SAK I_S_GrCoS
X1-24 X1-64 Parallel Connect Switch
I_A_SAK
Speed Adjustment Knob X1-09 I_S_FrqSwt
Gen Set Plug

G_R_SAK X1-55 Dual Frequency Switch

X1-25
I_S_DiaReq
X1-60 Diagnosis Request Switch
5V_SGRK
X1-28
I_A_SGRK
Speed Governing Rate Knob X1-10 O_S_STRT Starter Relay
G_R_SGRK X1-22
X1-27
O_S_IMPH
Intake Manifold Preheating Relay
X1-37 (Grid heater)

O_S_PREH
X1-40 Preheat Lamp
O_F_ENGN
Engine Speed Output Signal (PWM) X1-19 Water in Fuel Lamp No need to
O_S_WFLP
X1-23 connect lamps if
controlled by CAN
O_S_DIA Diagnostic Lamp
X1-35
Water in Fuel Sensor I_A_WFS
S 2 X1-12
+
1 G_R_WFS
Q 3 X1-32 O_S_IRS
X1-48 Idle to Rated Switch

5V_FSS
n X2-51
I_F_FSS O_V_24V The Max Current is 3A
Fan speed sensor X2-43 X2-24 1 1
G_R_FSS X2-30 O_V_24V
X2-74 2 2 The Max Current is 4A
5V_BPTS
P X2-64
& I_A_BPS X2-68 The sum of x2-56 and x2-74 shall less than 6A
Intake press-temp sensor I_A_BTS X2-26
t G_R_BPTS X2-34
U
O_V_24V
Engine

t I_A_CTS X2-56
X2-27 Fan control Output
Coolant temperature sensor G_R_CTS X2-33 X2-40 O_T_FAN (Electromagnetic/Silicone fan)
U
P 5V_RAILPS
X2-52 O_S_FAN2 Fan Relay 2 (Electromagnetic fan)
Rail pressure sensor I_A_RAILPS X2-66 X2-76
G_R_RAILPS X2-55
U
5V_OPTS X2-03 O_V_24V
P X2-06 O_T_MEUN Metering Unit
Plug

X2-63
& I_A_OPS X2-67
Oil press-temp sensor I_A_OTS X2-25
t G_R_OPTS 6-cylider 4-cylinder
U X2-47 H
X2-12
n I_F_CRSPOS X2-13 L Injector 1 Injector 1
Crankshaft speed sensor X2-59 H
I_F_CRSENG X2-14
(Magneto electric) U X2-60 X2-15 L Injector 2
G_C_CRS X2-73 H
X2-16 Injector 3 Injector 4
X2-17 L

X2-18 H
L Injector 4
X2-19
n 5V_CAS X2-53 X2-20 H
L Injector 5 Injector 3
Camshaft speed sensor I_F_CAS X2-41 X2-21
X2-22 H
(Hall) G_R_CAS X2-35 L Injector 6 Injector 2
U X2-23

Figure2.7.1A-Terminal diagram for 4M06 ECU

To prevent any damage to ECU, it is forbidden to carry out hot plugging operation on ECU.
25
Product

Electrical connection to the ECU

 ECU power line
 Pin No.: X1-01, X1-03, X1-05 (positive), X1-02, X1-04, X1-06 (negative)
 Functional description: ECU main power (24V DC)
 Operating voltage range: 9-32V
A 25 Ampere fuse is to be included in the positive line to the ECU

Wire diameter: 10mm2

Wire length
(recommended): <6m
Wire diameter: 2.5mm2
Wire length
Battery switch
Fuse (25A) (recommended): <2m
+ -
Negative Positive Generator
terminal terminal
ECU
Battery
+ -
Starter

Wire diameter: 2.5mm2 Engine

Wire length
(recommended): <1m

Body

Figure 2.7.1B-ECU and battery connection diagram

 Ignition switch (T15)

 Pin No.: X1-59
 Functional description:
 The switch is ECU power switch. After the switch is on, ECU will be in the
working condition, and after the switch is off, the engine will be stopped.
 Any interference on the T15 switch from other electrical devices should be
avoided, otherwise the switch may be off, but the engine cannot be stopped.
When the T15 switch is opened in order to shut off the engine, the main battery shall
continue supplying power to the ECU for 120 seconds via the main battery switch in order
to ensure all engine data is written to memory.

T15 switch 1 T15 switch 1 load

30 switch 1
ECU

Fuse
Batt+

Fuse T15 X1-59

ECU T15 dedicated relay

T15 switch 2
30 switch 2
Normal voltage
terminal load Other loads
Normal
voltage

Figure 2.7.1C-Key Switch T15

26
 Product

 Starter switch (T50)

 Pin No.: X1-58
 Functional description: The engine starter is controlled by ECU, the switch will be
onto control the start relay output. Benefits of the ECU-controlled start are as fol-
lowing:
 With the help of the second
start protection, the starter will
not respond after the start
switch is pressed again when
the engine has been started
 For example, the engine is
started, but the key is seized
in the state in which T50 is on.
At this time, the starter relay
will not respond. Figure 2.7.1D-Starter
 Controls start time and pre-
vent battery damage. In case
of difficult start, start circuit will
be powered off when the en-
gine is not started after a cer-
tain time (12s by default).
 Prevent blind meshing. When
the starter fails to drive the
crankshaft to a certain speed
within a certain period of time,
ECU will think that the starter
and the flywheel are not en-
gaged, and the relay will be
disconnected. At present, the
calibrated value is 12 s and 52
r/min.
 Control preheating. If the en-
gine is started before the in-
take air heating is not com-
pleted, the intake air heating
will be terminated, otherwise
the battery cannot withstand.

27
Product

 Speed adjustment knob

 Pin No.: X1-24, X1-09, X1-25
 Functional description: It is used to adjust the engine speed, and cannot be used
together with the speed fine-tuning switch.

 Speed governing rate knob

 Pin No.: X1-28, X1-10, X1-27
 Functional description: It is used to set the engine steady speed.

 Speed adjustment (+)

 Pin No.: X1-68
 Functional description: It is used to increase the engine speed slightly or continu-
ously. Press it to increase the speed by a fixed amount (optional), press and hold it to
increase the speed by N fixed amounts continuously.

 Speed adjustment (-)

 Pin No.: X1-51
 Functional description: It is used to decrease the engine speed slightly or continu-
ously. Press it to decrease the speed by a fixed amount (optional), press and hold it
to decrease the speed by N fixed amounts continuously.

 Parallel connection switch

 Pin No.: X1-64
 Functional description: It is the conversion switch between stand-alone power gen-
eration state and two or more grid-connected power generation state.

 Dual frequency switch

 Pin No.: X1-55
 Functional description: It is a changeover switch between 50 Hz power generation
mode and 60 Hz power generation mode.

 Idle to rated switch

 Pin No.: X1-48
 Functional description: The engine switches from the idle running state to the power
generation state at the rated speed.

 Fault Diagnosis
 Diagnostic request switch Pin No.: X1-60
 Diagnostic lamp Pin No.: X1-35 Figure 2.7.1E-Fault Diagnosis
 Functional description: Once the diagnostic request switch is pressed, ECU will flash
and the read number of lights will be the flash code. The switch is required to be
self-resetting.
Note !
When the diagnosis switch is off, the diagnostic lamp will stay on. If the switch fails to

28
 Product

reset automatically, the diagnostic lamp may stay on due to the diagnostic switch off.
Each flash code consists of 3 bits, for example: 3-2-1, the flashing diagram is as follows:

Figure 2.7.1E-Flash Diagram

 Engine speed output

 Pin No.: X1-19
 Functional description: This pin outputs the Pulse Width Modulation (PWM) square
wave signal to provide the engine speed information for the ordinary instruments,
and the speed is 4 pulses per revolution by default. If the instrument used is a Con-
troller Area Network (CAN) instrument, it is not necessary to connect this pin.
Note: When matching the instrument, it is necessary to inform the engine manufacturer of
the receiving pulse number of the instrument. 1 pulse/revolution, 2 pulses /revolution and
4 pulses /revolution are recommended.

 Intake air heating function

 Grid heater relay Pin No.: X1-37,
X2-24
 Preheat lamp Pin No.: X1-40,
X2-74 Figure 2.7.1F-Intake Air Heating

 Functional description: ECU senses the ambient temperature based on the temper-
ature sensor on the engine and automatically controls the operation of the intake
grille via the intake air heating relay to facilitate cold start. When the intake air heat-
ing is working, the light will stay on. After the air intake heating is completed, the light
will flash 3 times and then go out.

 Water in fuel alarm function

 Water in fuel sensor Pin No.: X1-12,
X1-32, X2-24 Figure 2.7.1G-Water in Fuel Alarm

 Water in fuel lamp Pin No.: X1-23,

X2-74
 Functional description: It is used to detect the water accumulated in the water cup of
the fuel coarse filter. When the water level exceeds the MAX scale, the water level
sensor (switch signal) will input the signal to ECU, and ECU will light up the water in
fuel lamp to prompt the operator to drain the water as soon as possible and to
maintain the coarse filter.

29
Product

 CAN communication
 Pin No.: X1-42, X1-43
 Functional description: It is used for information exchange between engine ECU and
other CAN nodes on the genset control card.
Note !
The twisted-pair wire is required, 25 units/m, and 120Ω terminal resistor is inte-
grated inside ECU;
If the CAN wire is shielded, the shielded wire must be grounded at one end only and the
other end is left unconnected. Two-end grounding is forbidden. In order to prevent the in-
fluence on ECU as a result that the current interference from the ground voltage differ-
ence is coupled to CAN wire.

 CAN flashing
 Pin No.: X1-45, X1-46
 Functional description: It is used for data transmission between external equipment
and ECU and is mainly used for data flashing and reading of engine fault codes.

 2P connector
 Pin No.: X2-24, X2-74
 Functional description: It is used as 24V power supply for relays/lamps of PowerKit
plug, the sum voltage of X2-56 and X2-74 shall less than 6A.

 Diagnostic interface
 Diagnostic interface connector has a standard OBD II 16-pin interface: square
 Part number: AMP 179631-1/2 Terminal: 776001-1.

Figure 2.7.1H-Diagnostic interface

Diagnostic interface number ECU terminal number Description

1 X1-45 CAN H_1
4 GND Ground
6 X1-42 CAN H_0
7 None K line
9 X1-46 CAN L_1
14 X1-43 CAN L_0
16 BAT+ +24V

30
 Product

2.8 Electronic Governor System for Mechanical Pump Engine

2.8.1 The Principle of the Electronic Governor System

Its system type is all-electronic single pulse speed and close loop position structure, provided
with functions of non-corresponding or corresponding control, speed and rated speed during
running maximum fuel supply control, emergency stop and etc.

It is also capable of adding other control functions according to the customer‟s particular re-
quirements.

Figure2.8.1A-Principle of the Electronic Governor System

2.8.2 Speed Controller

 The basic electronic characteristics

 Supply voltage : DC 24V（Scope 18V～32V）or DC12V（Scope9V～16V）

 Speed fluctuation ratio: ≤ ±0.25%

 Steady state speed droop: 0~5% Adjustable

 Ambient temp. : -40°C ~ +85°C

 Relative humidity: <95%

2.8.3 The Electromagnetic Actuator

The Electromagnetic Actuator is the executive element of the electronic governor. C2002
speed Controller that is single-loop control mode can matching all kinds of electromagnetic
actuator, such as A800C-W, A900C-W, A1000C-W-d1, A2000C-W-d1, A08A-W, A1AWL,
A1AWT, A3A-W, A3B, CA2-W.

2.8.4 Speed Pick-up

The Speed Pick-up of the Electromagnetic Governor is Speed Pick-up of magnetoelectricity,

31
Product

inner structure of which are made of sensor, loop, alnico and plug. Its structure refers to Figure
2.8.4A. The gap between the magnetic speed sensor and the ring gear teeth should not be any
smaller than 0.02 in. (0.45 mm). Usually, backing out the speed sensor 3/4 turn after touching
the ring gear tooth will achieve a satisfactory air gap.

Figure2.8.4A-Speed Pick-up Structure

32
 Product

3. Installation
Safety instructions
Users should carefully read and fully understand the safety instructions before installing and
operating the engine.

The purpose of these installation instructions is to:

 provide insight and advice in installing your engine
 establish conditions for trouble-free operation; avoid installation-related malfunctions and
any resulting consequential damage

It is essential when installing and operating diesel engines also to comply with the necessary
guidelines of the local authority.

S. I. Moteurs Baudouin is only liable for quality defects when these installation instructions
have been fully observed.

Failure to comply with the installation and

operating instructions defined by S. I. Mo-
teurs Baudouin will void the warranty.

Note !
After the diesel engine is unpacked, the user shall first check the diesel engine and its
accessories as per the delivery packing list and check the engine appearance for
damage and loose connections before carrying out the following tasks.

Check the water plug and oil plug check for water temperature and oil temperature sensors
and ensure that all parts to be self-provided are completely fitted.

Do not start the diesel engine before it is probably installed. When the diesel engine is running
in an enclosed environment, keep it well ventilated to ensure that the exhaust gas is ventilated
to the open air.

Please refer to the Generator Set Installation and Commissioning Manual for details.

33
Installation

3.1 Engine Lifting

3.1.1 Lifting device

 Use lifting devices to lift and move heavy parts over 20kg (44 lb.). Check the condition of
lifting hooks and chains.
 Verify the expiration date of appropriate protective equipment (goggles, gloves, shoes,
masks, overalls, helmet etc.) before beginning work.
 Do not use faulty or unsuitable tools.

3.1.2 Lifting the engine

The resistance of a lifting ring is reduced as

the angle between the slings or chains and
the engine hoist points fall below 90°.
 Use a lifting device with crossbars as
illustrated opposite.
 Avoid any contact between the slings
and the engine parts.
 Use fastening links and properly cali- Figure 3.1.2A-Lifting the engine

brated slings or chains.

Risk of death or injury due to heavy sus-

pended loads

3.1.3 Lifting Points

Note !
Please refer to the Generator Set Manual
when lifting generators.

For lifting the engine, use two lifting eyes

fitted on it.

During the lifting operation, never work un-

der suspended component, imminent dan-
ger of injury or death. Place the load on the
load before leaving your workplace. Never
be placed in the crane swing radius.

34
 Installation

The lifting points of 4M06 series engine are illustrated as followings:

4M06CR

Figure 3.1.3A-4M06CR lifting

4M06MP

Figure 3.1.3B-4M06MP lifting

35
Installation

3.2 Engine Mounting

In order to ensure the durability of the engine installation, the installation of the engine must
meet the following criteria:
 The engines‟ own mounting bracket should be used, and four-point support should be
adopted. The number of engine supports must not be reduced.
 Flexible support between the engine and the chassis should be arranged to reduce en-
gine vibration.

The mounting points of 4M06 series engine are illustrated as followings:

4M06CR

Figure 3.2A-4M06CR mounting

36
 Installation

4M06MP

Figure 3.2B-4M06MP mounting

37
Installation

3.3 Accessories

In order to ensure satisfactory engine life

and performance, the installation of pipes
must meet the following criteria:
 The intercooler pipe and the engine are
connected by a V-clamp. When in-
stalling, ensure that the direction of the
pipe in the expansion joint is consistent
with the direction of the air flow. Add
O-ring seal during installation.

 Two cooling brackets need be installed

between the intermediate cooling pipe
and the tank through the V-type clamp. Figure 3.1

 The coolant connecting pipe relates to

the engine through bolts, and O-rings Figure 3.2

are installed between the connecting

flanges.

 The coolant connecting pipe relates to Figure 3.3

the clamp and the radiator through the

hose.
 The engine coolant outlet tube is con-
nected to the engine via a clamp.

38
 Installation

3.4 Air Intake System

The air intake system must avoid the followings entrance:

 Water
 Dust
 Exhaust gas.

3.5 Exhaust System

The exhaust system must meet at least the following requirements:

 Exhaust back pressure must not exceed the limits in the engine data sheet.
 Exhaust system components should not exert excessive stress on the exhaust manifold
or turbocharger due to their own weight, inertia, relative movement between components,
or dimensional changes due to thermal expansion.
 The exhaust pipe must not have sharp turns or right-angle bends. The bend radius of the
pipeline should be increased as much as possible and welding with sharp corners is not
allowed.
 When the exhaust pipe is close to the intake pipe, rubber parts, plastic parts, fuel tanks,
etc., an insulation board must be added in the middle and the distance should be in-
creased as much as possible.
 The inner diameter of the exhaust pipe should not be smaller than the inner diameter of
the engine exhaust port.
 The exhaust system must be able to completely prevent rain, snow or splashing water
from entering the engine block or turbocharger.
 The exhaust gas must be ventilated so that it does not negatively affect the function of the
air filter, the efficiency of the cooling system, the surroundings of the engine or the health
and safety of personnel.

3.6 Cooling System

In order to ensure satisfactory engine life and performance, the installation of the radiator must
meet the following criteria:
 When installing the radiator, install the elastic support.

Figure 3.6-Elastic Support

39
Installation

 If the PowerKit is installed in a soundproof box, seal rubber is installed around the radiator
to prevent the hot air in the engine compartment from flowing back into the air intake
channel.
 Radiator grounding measures must be taken to eliminate potential differences and pre-
vent electrical corrosion (aluminum radiators do not require this).
 The direct windward surface of the radiator should not be blocked, and the direct wind
area should be greater than or equal to 80% of the radiator's positive area.

3.7 Lubrication System

Users must follow the requirements in 6.2 Lubricant Recommendation.

3.8 Fuel System

The installation of the fuel system must comply with the following requirements:
 When the engine is stopped, the fuel system does not allow the fuel to flow into the en-
gine through the fuel inlet pipe or the injector return line due to gravity.
 The injection resistance of the fuel injection pump shall not exceed the specified value
with a clean fuel filter. The resistance is based on the half-full fuel tank.
 The return oil must not generate pressure fluctuations in the pipeline.
 The fuel tank must have a vent and fuel return connection to allow air and other gases to
properly separate from the fuel without pressure in the fuel tank. The vent must also pre-
vent the entry of dirt and water.
 The temperature of the fuel entering the engine must be lower than the specified value in
the engine data sheet.

3.8.1 Fuel Tank

 The lowest position of the fuel tank shall be no less than 1m(3.3ft) from the fuel pump of
the engine, and the location shall be far away from the heat source. The fuel tank shall
have proper space and ventilation.
 The device should be set up to periodically drain the condensed water in the fuel tank and
the filter, and signs should be placed to remind the user of such.
 The fuel tank has ventilation function to prevent the pressure inside the tank from being
too high and the vent hole should be dustproof and waterproof.
 The fuel tank must have 5% liquid thermal expansion space to prevent the fuel from
overflowing after it expands.

3.8.2 Fuel Line

 The fuel line shall comply with the requirements of the fuel line matching specification.
 The diesel piping should be able to withstand sufficient operating vacuum without damage
or collapse.

40
 Installation

 Both suction and return lines must be

installed at the bottom of the tank and
must be kept at a distance (≥300 mm)
Filler port
from each other, and the line must be Fuel
filter screen
open. inlet

 If the fuel line needs to be fixed, clamps filter

with rubber gaskets should be used on

the pipeline. No other components can Figure 3.8.2-Fuel Line

be fixed on the pipeline. DO NOT tie the

fuel line bundles with the wire har-
nesses.

3.9 Engine Control System

3.9.1 Startup Circuit

2
 Wire size of starting main cable: ≥50mm .
2
 Wire size of battery negative terminal ground wire: ≥50mm .
2
 Wire size of starting system control end cable: ≥1.5mm .
 The wiring terminals of starter shall be equipped with protective caps.
 Non-electronic controlled engine shall
be equipped with starting protection
preventing second start up.
 Before performing electrical connection,
remove the paint on connecting points.
 Working environment temperature:
-15°C~50°C.
 Discharge current at low temperature:
≥850CCA.
 Rated voltage 12V, maximum power
4.0kW.
 The maximum resistance of the main
circuit of the starter is ≤6mΩ, and the
maximum resistance of the control cir- Figure3.9.1A-4M06 Starter Wiring Diagram

cuit is ≤90mΩ.

3.9.2 Charging Circuit

 The alternator must be agile rotation and have not abnormal noise.
 The charging cable shall be a complete cable without intermediate connector.
 Terminals of B+/D+/W shall be provided with protective caps.
 Working environment temperature: -40°C~105°C.

41
Installation

 The maximum leakage current: 2mA.

 Rated alternator speed 6000rpm, maximum operating speed 11000rpm.

The schematic diagram of the charging motor wiring is as follows:

Figure3.9.2A-4M06 Charging Motor Wiring Diagram

Parameters table

Rated Voltage Rate Current

28V 80A

TEST Ambient Temp Voltage Speed Current

n=1800rpm I≥45A
Cold state
n=6000rpm I≥95A
25±5 ℃ 27V
n=1800rpm I≥34A
Hot state
n=6000rpm I≥80A

Generator zero current ≤1400rpm

42
 Installation

3.10 Electrical Components

3.10.1 Air Heating

 Air heating cable cross-section area ≥

2.
25mm
 Air heating cable resistance (sum of 30,
31 ends) ≤ 1 mΩ.
 Air heating control line cross-sectional
2
area ≥ 1.5 mm . Figure 3.10.2A-4M06 Air Heating Wiring Diagram
 The air heating cable and its control BAT
cable must relate to a protective cap.
No metal exposure is allowed. Air heater 250A fuse

 Working environment temperature: Relay

-15°C~50°C.
 Nominal voltage: DC24V.
The air heater wiring diagram is as fol-
2.19 2.15
ECU
lows:
Figure 3.10.2B-4M06 Air Heating Wiring Diagram

3.10.2 Sensors

 Sensor wiring terminal (male tab type) shall be provided with protection after connection.
 Sensor connector shall be inserted in place, well positioned and firmly fastened.
 For resistance type sensors, for example, temperature and pressure sensors, their cable
lengths connecting to the instrument shall be less than 10m.
 Sensor harness sheath shall be protected (preferably by expansion joint).
 All sensor harnesses of the generating set shall comply with specifications, without cop-
per conductor exposure or burrs.
 For analog sensors, resistance type temperature and pressure sensors, their harnesses
shall be shielded wire, with shielding layer reliably grounded and not exposed. Rotation
speed sensor wire should be twin twisted.
 Harness must be far from hot parts and components, for example, turbocharger and ex-
haust pipe.
 The power supply of sensor system must be under the control of the master key switch of
the generating set.
 Ensure the power supply of sensor is reliably cut off when the generating set is powered
off.
 The wire size of sensor harness (copper conductor) shall not be less than 1.5 mm²
2
(0.0023 in ).

43
Installation

3.11 Installation and debugging of Electronic Governor System

3.11.1 Speed controller

The speed Controller is installed on the control box or fixed other peripheral equipment in the
engine. It should be installed in the place of air drying and temperature suitable. If it be in-
stalled in the place of more water and humidity, the speed Controller should be mounted ver-
tically. Its outline and installing size refers to Figure3.11.1A.

Figure3.11.1A-Outline and Installing Size of the C2002 Speed Controller

Note!
An over s-peed shutdown device, independent of the governor system, should be provided to
prevent loss of engine control which may cause personal injury or equipment damage. Do not
rely exclusively on the governor system of electric actuator to prevent over s-peed. A second-
ary shut off device, such as a fuel solenoid, should be used.

 Connection diagram of the C2002 speed Controller

C2002 speed Controller‟s connection diagram for normal generator set refers to Figure3.11.1B

44
 Installation

Figure3.11.1B-Connection Diagram of the C2002 Speed Controller for Normal Generator Set

Wire harness
Terminal
Less than 6 meters More than 6 meters

1,2 shall connect with the actuator winding end 1 mm² 2.5 mm²

3,4 shall connect with a speed sensor ( the mini- 0.5 mm² 1 mm²
mum operation signal are both 2.5V AC)
5,6 shall connect with the battery with connect 15A 1 mm² 2.5 mm²
fuse (reference to the controller voltage value)

7, 9 shall connect with the Speed Potentiometer, if

not connected with the Speed Potentiometer,
please short circuit them. The signal points are millampere level cur-

7,12 shall connect with the idle switch rent, so it can be used 0.5 mm2 ~ 1 mm2
wire harness to connect. In a strong mag-
10,11 shall connect with the droop switch
netic field environment, you shall use the
13 is the access terminal (as input signals for shield lines to connect; shielding net shall
connect the grounded end of the controller
synchronizer, load distribution, ramp generator
effectively.
access points which for the combined machine or

extraordinary setting)

45
Installation

14 is the auxiliary power output for +10V DC, load

should be less than 20mA

 The Electromagnetic Actuator connects to Terminals 1 and 2 and battery connects to

Terminals 5 and 6. Terminals 1, 2, 5, and 6 should be #16 AWG (1 mm sq) or larger.
Long cables require an increased wire size to minimize voltage drops. The battery posi-
tive (+) input, Terminal 6, should be fused for 15 amps as illustrated.
 Magnetic speed sensor connects to Terminal 3 and 4 MUST BE TWISTED AND/OR
SHIELDED for their entire length. The speed sensor cable shield should only be con-
nected to Terminal 4. The shield should be insulated to insure no other part of the shield
comes in connect with engine ground, otherwise stray speed signals may be introduced
into the speed Controller to stop the engine.
 The remote potentiometer connects to Terminal 7 and 9. If it resistance is 5KΩ, speed
adjusting range is2400HZ.
 Speed droop connects to Terminal 10 and 11. When the Terminal 10 and 11 is off, speed
droop is 0; When the Terminal 10 and 11 is closed, speed droop range is 0-5%.
 Rated and idle speed switch connects to Terminal 7 and 12. The switch close for idle, the
switch off for rated speed.
 Terminal 13 receives input signal from load distribution device, automatic synchronizer
device and other governor system auxiliary device.
 Terminal 14 output +10 volt regulated supply.

Figure3.11.1C-Connection Diagram of the ESG2002 Series Electronic Governor System

3.11.2 Adjustments before Starting Engine

 It is available to adjust the “starting fuel” potentiometer to make engine start smooth and
control smoke.

46
 Installation

 Adjust the “starting fuel” potentiometer, rotate clockwise to increase (the smoke will be
large when the starting fuel is too much), and rotate anticlockwise to decrease (too
small to start successfully);
 The controller has been set when leaving the factory (similar to the marked dial, with
the arrow pointing at 3 o 'clock), and there is no need to adjust it on site.
Note!
The starting potentiometer is a single-turn potentiometer, which can only rotate by 300 de-
grees (each small compartment is 30 degrees, which is equivalent to turning the clock hour). It
is strictly prohibited to use inappropriate tools or exert too much force, which may cause
damage to the potentiometer.

 “Speed ramping” controls the acceleration time of a diesel engine from idle to rated
speed.
 Clockwise rotation is to extend the acceleration time;
 Counterclockwise rotation reduces the acceleration time;
Note!
The acceleration-time potentiometer is a single-turn potentiometer. The potentiometer can only
rotate by 300 degrees. Do not use improper tools or exert too much force, which may cause
damage to the potentiometer.

Check to insure the GAIN and STABILITY adjustments, normally this value is set mid position
by factory.

Leave factory conditions of Red State Switch is , namely RSW-1, RSW-3 = OFF, RSW-2
= ON.
Rated and idle speed of the speed Controller had been set by factory. Normally, this value is
near from the user‟s engine working rotate speed value. In practice, after some adjustments,
controller can achieve rated and idle speed, and the stability would be very well.

3.11.3 Adjustment of the Controller after Starting

 Crank the engine with D.C. power applied to the governor system. Start fuel quantity
varies with environmental temperature of engine start. Though adjusting start fuel quan-
tity potentiometer; exhaust smoke from the engine can be adjusted to the best state.
 The governor system should control the engine at low idle speed. If the engine is unsta-
ble after starting, turn the GAIN and STABILITY adjustments counterclockwise until the
engine is stable.
 The governed speed set point is increased by clockwise rotation of the SPEED adjust-
ment control. Remote speed adjustment can be obtained with an optional Speed Trim
Control.
 Once the engine is at the operating speed and at no load, the following governor per-
formance adjustments can be made.
(1) Rotate the GAIN adjustment clockwise until instability develops. Gradually move
the adjustment counterclockwise until stability returns. Move the adjustment one divi-
sion further counterclockwise to insure stable performance.
47
Installation

(2) Rotate the STABILITY adjustment clockwise until instability develops. Gradually
move the adjustment counterclockwise until stability returns. Move the adjustment one
division further counterclockwise to insure stable performance.
(3) Gain and stability adjustments may require minor changes after engine load is ap-
plied. Normally, adjustments made at no load achieve satisfactory performance. A strip
chart recorder can be used to further optimize the adjustments.
 After the governor speed setting has been adjusted, place the optional external selector
switch in the IDLE position. The idle speed set point is increased by clockwise rotation of
the IDLE adjustment control.
When the engine is at idle speed, the speed Controller applies droop to the governor
system to insure stable operation.
Note!
The starting potentiometer is a single-turn potentiometer, which can only rotate by 300 de-
grees. It is strictly prohibited to use inappropriate tools or exert too much force, which may
cause damage to the potentiometer.

 Through the above adjustments engine still unable to stability, it needs to be adjusted
Red State Switch now, Figure3.11.3A four cases (a: RSW-1、RSW-3 = ON、RSW-2 =
OFF; b: RSW-1、RSW-2 = OFF、RSW-3 = ON; c: RSW-1、RSW-2 = ON、RSW-3 = OFF;
d: RSW-1、RSW-3 = OFF、RSW-2 = ON). After every adjusting Red State Switch go on
the (1) and (2) adjusting procedure again. If it is still unable to stability, should inspect
engine and fuel pump for service condition. And then, contact with manufacturer.

Figure3.11.3A-Red State Switch

3.11.4 Speed Droop Operation

 Droop is typically used for the paralleling of engine driven generators.

 Place the optional external selector switch in the DROOP position, which is connected
Terminals 10 and 11. Droop is increased by clockwise rotation of the DROOP adjustment
control. When in droop operation, the engine speed will decrease as engine load in-
creases. The percentage of droop is based on current change from no load to full load of
the actuator.

 After the droop level has been adjusted, the rated engine speed setting may need to be
reset. Check the engine speed and adjust the speed setting accordingly.

3.11.5 Accessory Input and Output

 When the Auxiliary Terminal 13 accepts input signals from load sharing units, auto syn-
chronizers and other governor system accessories are directly connected to this terminal.
48
 Installation

It is recommended that this connection form accessories should be shielded as it is a

sensitive input terminal.

 When an accessory is connected to Terminal 13, the speed will decrease and the speed
adjustment must be reset.

 The +10Volt regulated supply, Terminal 14, can be utilized to provide power to our gov-
ernor system accessories. Up to 20mA of current can be drawn from this supply. Ground
reference is Terminal 7.

Note!

A short circuit on this terminal can damage the speed Controller.

3.11.6 Accessory Input and Output

 Connect idle switch at the 7/12 terminal, disconnect (dial OFF) and rise to the rated speed.
If the actual speed is inconsistent with the target speed, the “speed” potentiometer can be
adjusted:

 Increase of engine speed by rotating clockwise;

 Reduce engine speed by rotating counterclockwise;

Note!

The rated speed potentiometer is multi-turn potentiometer. Do not use improper tools or exert
too much force, which may cause damage to the potentiometer.

 For convenience of adjustment, the speed controller is connected with the speed trimmer
potentiometer, which is used to accurately adjust the rated speed. The engine speed in-
creases by rotating clockwise while decreases by rotating counterclockwise.

 The adjustment range of the speed trimmer potentiometer is 200r/min. It is recommended

that the difference between the actual engine speed and the target speed be adjusted
within ±50r/min .If the difference exceeds ±50r/min, the rated speed potentiometer needs
to be adjusted.

Note!

It is equipped with trimmer potentiometer when leaving the factory. If the customer does not
connect it, the 7/9 terminal shall be shorted circuit.

49
Installation

3.12 Genset Installation Recommendations

Users must choose the genset installation location very carefully in order to not disturb anyone
and not to cause noise pollution. If the location is not appropriate, enclosure have to be insu-
lated for noise reduction. Also, the correct type of exhaust silencer must be used if necessary.

 The genset room should be well ventilated. The foundation of the unit should be solid and
conform to local code. After compacting hard soil, the minimum precast concrete structure
foundation of 200mm thick should be built on this foundation.
 When installed, the shock absorber is evenly placed under the two channel steel of the
common chassis of the unit, leveling with the flat pad, and its levelness is measured with
the level gauge. Keep the unit level; In addition, the packaging base is not allowed to be
used as the basis for starting up operation.
 When the user is building the genset room, the steel I-beam for lifting should be embed-
ded in the roof above the unit for later maintenance.
 The inner diameter of the exhaust pipe should not be less than 140mm, the bending pipe
should not be more than 3, and the bending Angle should be greater than 90 degrees.
 There should be sufficient maintenance and inspection space around the unit. There
should be at least 1.5m space around the unit.
 The machine room should be equipped with fire extinguishers and other fire tools.

Figure 3.11-Genset installation

50
 Installation

4. Operation
The first engine commissioning process should be handled by S. I. Moteurs Baudouin ap-
proved personnel. The successful completion of this process, along with the checks and ad-
justments required by S. I. Moteurs Baudouin, will ensure that the engine runs efficiently,
reliably, and safely.

Failure to comply with the installation and

operating instructions as defined by S. I.
Moteurs Baudouin will void the warranty.

People will be required to wear Individual Protection Equipment (IPE) and use correct tools
following official standards.

Make sure that the engine is correctly protected regarding its environment conditions.

Take the necessary measures for the emergency shut-off of the fuel or air supply to prevent
from over-speed risks.
 Check the cleanliness of circuits.
 Check for free circulation of gases in exhaust ducts.
 Check the fuel supply.
 Check coolant level and fill if necessary.
 Check oil level and fill if necessary.
 Check air clogging indicator.
 Pre-lubricate before engine start-up after an engine has been stopped longer than 24h,
for a shorter period, pre-lubrication is unnecessary.

51
Operation

4.1 Preparations before Start

Oil
 Adding of engine oil
 Open the oil filler cap and add the
engine oil.
 Using the dipstick to check the oil
level.

Figure 4.1A-Adding of engine oil

Fuel
 Adding of fuel
 The diesel fuel used shall meet the
specification.
 The diesel fuel used must be clean.
It's better to place the diesel fuel
under stationary state for more
than 72 hours before adding. The
diesel fuel shall be added into the
fuel tan-k via the built-in filter
screen.
Figure 4.1B-The fuel level

Coolant
 Adding of coolant
 The coolant is mixed from treated
clean water and anticorrosive
agent or antifreeze. Ensure to
strictly abide by the specification of
the additive manufacturer during
mixing.
 Add coolant through the water filler
port of radiator or heat exchanger
Figure 4.1C-Adding the coolant
and bleed the air from the cooling
circulation system.

52
 Operation

4.2 Starting Up

The following starting/stopping procedure is a simple example (not binding) and it‟s based on a
simple starting control panel equipped with starting key. Please refer to the genset and/or
genset control panel use & maintenance manual for the starting operation mode.

 Before starting the engine, operate the

stop control lever on the fuel injection
pump to ensure flexible motions.
 Turn the key to position “1” to power on
the control panel. The “oil pressure
warning lamp" automatically will turn on
for 10s (Safety line test of ultra-low en-
gine oil pressure). It‟s recommended to
test the indicator lamps, bulbs, and but-
tons once (by pressing the touch button
10 on the control panel).
 Turn the key to position “START” to Figure 4.2-Switch

start the engine and then release the

key. The key will automatically return to
position “1”.

Note!

 At the start of diesel engine, the engine speed should not be more than 400r/min. If the
diesel engine fails to start within 12s, immediately release the button and wait for 1min
before retry.
 If the engine can‟t be started by three consecutive attempts, stop the attempt and find out
and solve the malfunction before retry.
 During the working of engine, the “oil pressure warning lamp” and the "battery power”
indicator lamps are all off.
 All indicator lamps are off during normal running of engine.
 In event of abnormality, the “horn” will issue warning sound.
 The auxiliary starter shall be used to start the diesel engine under cold temperature.
 By activate the electric heating flange via relay, the engine can be started success-
fully under low-temperature environment.

53
Operation

4.3 Operation of the PowerKit Engine

 After the start of diesel engine, idle the engine for 3min, and then increase the speed to
1000r/min to 1200r/min with some load. Only when the coolant temperature is above
60ºC and the oil temperature is above 51ºC, can the engine run with full load. The load
and speed should be increased gradually.
 In the first running in period of 60h, the diesel engine should work with load less than the
moderate load.
 Parameters and checking locations to be observed always during operation are as below:
Oil pressure of main oil passage : 200~500 kPa (rated working conditions).
 The oil temperature in main oil passage: ≤115 ºC.
 Coolant outlet temperature: (75~95) ºC.
 Exhaust temperature after turbine ≤650 ºC.
 Check the exhaust color, to estimate
the performance of the injector and the
load of the engine. In the case of seri-
ous black or white smoke, stop and
check the engine.
 Check the diesel engine for presence of
water, gas, and oil leakages. Figure 4.3-Smoke

Users should immediately stop the genset,

check and troubleshooting if there is ab-
normal phenomenon!

54
 Operation

4.4 Precautions for running in cold environments

 Fuel: Choose a grade of diesel fuel depending on the environmental temperature.

 Lubricating oil: Choose lubricating oil of different viscosities depending on the seasons.
 Coolant: Add antifreeze additive into the cooling system and choose the coolant of differ-
ent grades depending on the ambient temperature.
 Start: The auxiliary starter can be adopted if necessary in winter. After starting the engine,
only operate the engine with load when the oil pressure and water temperature are nor-
mal.
 Before the cold season begins, be sure to check the electrolyte liquid level, viscosity and
battery voltage. If the engine is not going to be operated for a long time and under very
low temperatures, the battery should be removed and stored in a warmer room.
 Shut-down of the engine: When shutting down the engine in a cold climate, unload the
engine first and then run the engine at idling speed for 1 to 2 minutes. And then stop the
engine after the water and oil temperatures decrease. The coolant with antifreeze addi-
tives should not be drained out after shutdown. Otherwise, open the drain valve or plug on
the engine body, oil cooler cover, and radiator and water inlet pipe to drain the coolant
completely to prevent the engine from being frost cracked.

55
Operation

4.5 Stopping the PowerKit Engine

Avoid shutting down the engine at full load. Before the shut-down, engine load and should be
reduced, and the engine should operate at low-load condition for 3 to 5 minutes. This allows
the piston, cylinder head, liner, bushing and turbocharger to cool down, avoiding cylinder and
bearing damage. This is particularly important for turbocharged engines because the bearing
and oil seal in the turbocharger can be affected by the high temperature of the exhaust gas.
When the engine is running, the heat will be transferred away by the cycling lubricating oil.
When the engine shuts down suddenly, the turbocharger temperature will increase greatly and
cause the bearing or the oil seal to fail.
 Turn the key switch to position “0” or
press the stop button to stop running of
engine, till the engine stops rotation or
the speed indicator on the instrument
panel points zero.
 For the engines that don't use anti-
freeze in the engine coolant, drain the
coolant after shut-down in cold weather
to prevent freezing damage to the en-
gine. The draining valve under the oil
cooler can be used to drain the water
inside the engine. The drain plug on the Figure 4.5-Switch

radiator should also be removed to

discharge the coolant in the radiator.

56
 Operation

4.6 Electronic control system

Reading the fault code via the diagnostic switch:

 Press the diagnostic switch (diagnostic lamp comes on), and then release to reset the
diagnostic switch (diagnostic lamp turns off).
 The diagnostic lamp flashes and reports the fault code.
st
 Repeat step 1 for several times, the subsequent fault codes will be shown one by one.
When the first fault code is repeated, it indicates that all the fault codes have been read.
 Check the "List of fault codes" to find the explanation corresponding to each fault code
and you can determine the current fault.
Please check the code sheet at 6.5 Common Faults and Troubleshooting.

Note !
Clearing the memory of historical errors manually:
 Press the fault request switch before ignition switch (T15) is on, then turn on the: Igni-
tionswitch (T15) and hold the diagnostic request switch for 4-30s before releasing.
 If you fail to delete a fault code, it remains a current fault.
You need to resolve the current fault before clearing the error memory in ECU.
If you fail to clear the fault code, please notify your local Baudouin representative as soon as
possible.

57
Maintenance

5. Maintenance
5.1 General Safety Conditions for Maintenance

SAFETY WARNING

Users should carefully read the safety instructions before installation and operation of the en-
gine.
Electrical insulation controls must NOT be done with a voltage higher than 50VDC

Safety conditions for preventive and corrective maintenance operations are intended to
check.
 Engine and generator alignment.
 The tightness of the entire engine unit on the frame.
 The tightness of the couplings and all elements transmitting power.
 The isolation and condition of electrical equipment.
 The condition and tightness of electrical connections.
 Control of oil, fuel and coolant levels.
 Operation of the alarm safety devices.
 Replacement of oil, fuel and air filters.

58
 Maintenance

5.2 Maintenance Table

Check = •
Mandatory maintenance, in operation working hours (H) or
Adjust = о
period (months - M), every, which occurs first
Clean = Δ
Replace = □ MD M0 M1 M2 M3 M4 R1 R2
First Every Every Every Every Every Every
Hour 8
50 500 1,000 2,000 4,000 8,000 12,000
OPERATION
First Every Every Every Every Every Every
Month
2 12 12 12 24 60 96
Walk around inspection • •
Coolant level and temperature • •
Fuel level in the tank • •
Check Oil level • •
Air cleaner service indicator • •
Cooling fan status • •
Fuel pre-filter / water separator fil- 1
• • □
ter(s) element(s)
Belt(s) • • □
Engine oil □ □
Oil filter(s) element(s) □ □
Defaults recorded in ECU (if
•
equipped)
2
Fuel filter element(s) □
Engine and generator mechanical
•
connection
Conditions and tightness of all
•
electrical connections
Air filter element - Clean when vis-
ual indicator turns red - max 3 Δ □
times.
The rocker arm and cross-bar
о о
clearance

Note 1/2: The indicated change interval running hours is the maximum period when using good quality
fuel, (EN 590 standard); this is reduced if the fuel is low quality fuel, if the fuel is contaminated, if the fuel
has presence of water.

59
 Maintenance

Check = •
Mandatory maintenance, in operation working hours (H) or
Adjust = о period (months - M), every, which occurs first
Clean = Δ
Replace = □ MD M0 M1 M2 M3 M4 R1 R2
First Every Every Every Every Every Every
Hour 8
50 500 1,000 2,000 4,000 8,000 12,000
OPERATION
First Every Every Every Every Every Every
Month
2 12 12 12 24 60 96
Battery, battery electrolyte level,
•
battery charger, battery cables

Aftercooler Δ

Radiator and cooling system Δ

Radiator pressurized cap •

Δ/
Breather filter element (if equipped)
□
Belt tensioner(s) •
State and tightness of starter •
Turbocharger - axial and radial
•
clearances
Turbocharger air intake side and air
•
pipes
Sensor •
Coolant □
Fuel flexible hoses/pipes □

Coolant flexible hoses □

3
Overhaul(In-Structure) •

4
Overhaul(Major) •

Note 3: Reference to Chapter 5.3.5.2 Overhaul (In-Structure).

Note 4: Reference to Chapter 5.3.5.3 Overhaul (Major).

60
 Maintenance

5.3 Maintenance Operation

Note!
Before performing any maintenance work, the engine must be turned off and have
cooled off, the battery main switch must be switched off and the ignition key removed,
put ‘Do not start the engine’ sign aside the gen-set.

5.3.1 MD/M0 Maintenance Operations

Note!
M0 operations are operated on the first 50 hours, not every 50 hours.
 Walk around inspection
A careful and thoroughly walk-around inspect can find problems in advance and avoid
costly losses and serious breakdowns.
 Check for any type of leak, inspect the exterior of the engine to make sure there is no
fuel, oil and coolant leakage, if leak is observed, clean the leaking area, find the rea-
son and repair it.
 Check if the vibration is in normal condition, and if the speed is stable. If the foundation
vibration is more serious than before, stop the engine and check if there are problem
on the engine parts or engine mounting system. If the problem cannot be solved,
consult your Baudouin dealer in time.
 During the normal running of engine, observe exhausts color, when the color is ab-
normal, check the cause and do troubleshooting.
 Check the air inlet pipe for wear, damage, loose clamp, which causes dirt to enter the
intake system.
 Check the exhaust system for leaks, if leak is observed, find the reason and repair it.
 Check the wiring and the wiring harnesses for loose connection or worn.
 Check the fuel lines for leaks, if leak is observed, find the reason and repair it. Do not
allow dirt to enter the fuel system. Dirt in the fuel system will seriously damage the fuel
injection equipment and could be expensive to repair.
 Check the coolant pump, the pump seal is lubricated by coolant in the cooling system,
it is normal for a small amount of leakage to occur when the engine cools and the parts
contract. Excessive coolant leakage may indicate the need to replace the water pump
seal.

 Check the coolant level

Note!
Risk of scalding!
The cooling system is under pressure and the coolant is hot. Never open the radiator
filler neck to check the coolant level while the engine is in operation or immediately
after it is stopped to avoid the skin burns.

61
Maintenance

 Inspect the coolant level gauge on

the radiator tank to check if the
coolant level is appropriate.

Figure 5.3.1.A

 Filling Coolant
Note!
Do not let coolant drip or leak out onto the ground or into the bodies of water while
filling. Otherwise, the environment will be damaged.
The engine's cooling system is to be filled with a mixture of coolant, glycol, and special
additives .Never add the normal plain water only. Specific requirement about coolant,
see the Part "Annexes”.
Coolant can only be filled at the filler.
The engine damage can be caused by excessive temperature difference. When filling
with cold coolant in an engine at operating temperature there is a risk of engine damage
caused by excessive temperature difference. For this reason, do not add cold coolant to
a warmed-up engine.

 Remove coolant filler cap.

 Slowly fill coolant until the coolant
higher than the min. mark.

Figure 5.3.1.B

62
 Maintenance

 Close cap.
 Run engine for apporx.15 minutes at
rated speed.
 Check the coolant level gauge. If it is
need to fill, shut off engine and care-
fully unscrew cap with safety valve to
the first stop to release pressure. Let
the engine cool down, and then fill the
coolant.
 Check coolant before the next com-
missioning (with engine cold). Add
coolant if necessary. Figure 5.3.1.C

 Repeat this procedure until coolant

no longer is added.

 Check the fuel

Note!
Do not allow dirt to enter the fuel system. Before disconnecting any part of the fuel
system, thoroughly clean around the connection. When a component has been dis-
connected, for example a fuel pipe, always fit protective covers and plugs to prevent
dirt ingress. Failure to follow these instructions will lead to dirt entering the fuel system.
Dirt in the fuel system will seriously damage the fuel injection equipment and could be
expensive to repair.

Never use tanks made of galvanized steel for fuel storage. The fuel oil reacts chemically
with the zinc coating to produce powdery fragments which clog the fuel filter and may
damage the fuel pump and injection nozzle.

When adding fuel, never allow fuel overflow as this may cause a fire. If any fuel is
spilled, wipe it up completely. Never bring flames near fuel because it is highly flam-
mable and dangerous.

Check the fuel level with fuel meter or fuel gauge, which is installed in the side of the fuel tank.
If the fuel is not enough, add the recommended fuel through fuel filler to fill the tank. Keeping
the tank filled with fuel reduces the condensation of moisture and helps to maintain the fuel at
a low temperature (important for engine performance).
Refill at the end of work each day in order to prevent fuel contamination caused by condensa-
tion. Condensation which occurs in a partially filled tank accelerates the reproduction of mi-
croorganisms, causing the fuel filter to be clogged and restricting fuel flow.

63
Maintenance

The engine is equipped with a fuel-water separator, completely discharge all accumulated
water. Water in fuel has a severe impact on engine performance and may damage the engine.

 Check the oil level

Note!
Check the oil level when the engine is horizontal at idle speed or engine stopped. If
check the oil level when engine stopped only after at least 20 minutes have passed
since the engine was switched off.

 Pull out oil dipstick.

 Wipe off oil dipstick with a lint-free
cloth.
 Reinsert oil dipstick all the way.

Figure 5.3.1.D

 Pull out oil dipstick again and check

oil level.
The oil level should be between both
of the marks on the dipstick and
should never drop below the lower
mark.

 Reinsert the oil dipstick all the way.

If the oil level is too low, refill with new Figure 5.3.1.E

oil.

64
 Maintenance

 Check the air cleaner service indicator (if equipped).

 If equipped with a dust indicator,

con-duct maintenance only when the
clog warning sign appears.

Figure 5.3.1.F

 A red signal appears as a warning

when the air cleaner element be-
comes clogged and causes an ab-
normally large pressure difference
between be-fore and after the air
cleaner. When a red signal appears,
clean the air cleaner element imme-
diately or replace it with a new ele-
ment.
Figure 5.3.1.G

 After the element is cleaned or re-

placed, press the reset button located
at the upper part of the indicator to
cancel the red signal.
 While serving the air cleaner, do not
enter dust into the air cleaner or
damage the element.

 Check the valve vacuator.

Figure 5.3.1.H

65
Maintenance

 Check the fan

Note!
Do not rotate the engine by pulling or
moving the fan. Otherwise, it will damage
the fan blades, cause fan failure and
cause personal injury or property loss.
The crankshaft should be rotated using
an accessory drive shaft or crankshaft
turning tool.

Figure 5.3.1.J

 Visually inspect the cooling fan daily.

Check for cracks, rivet looseness,
blade bend or looseness. Check the
fan and make sure it is firmly installed.
Tighten the screws if necessary.

Figure 5.3.1.K

 Replace the damaged fan on the

original equipment with a fan of the
same part number. Refer to the
tightening torque of bolts in the
maintenance manual.

 Check the belt tension

Note!
Slippage of loose belts can reduce the efficiency of the driven components. Vibration of
loose belts can cause unnecessary wear on the belts, pulleys, and the relevant bear-
ings.

66
 Maintenance

 Check the belt

 Make sure all belts are fully engaged
on all pulleys and riding in the correct
grooves.
Look for cracks on the ribs of the belt,
fraying at the edges of the belt, or any
other signs of unusual wear.

Figure 5.3.1.L

5.3.2 M0/M1 Maintenance Operations

Note!
M0 operations are operated on the first 50 hours, not every 50 hours.

 Check the engine and generator connection

 Check if the engine and generator
connection is tight; if not, retighten
it. Reference to the Appendix about
the torque.

Figure 5.3.2.B

 Replace engine oil

Note!
Be careful when draining hot engine oil. Hot engine oil can cause burns to un-protected
skin. Comply with applicable rules and regulations for the work place. Obey environ-
mental regulations for the disposal of used oil.
To perform this operation with warm engine, to get a better fluidity of the oil and get a
full discharge of oil and impurities contained it.

67
Maintenance

 Remove the oil drain nut and re-

move the lubricant oil cap to assist
the flow of the engine oil. Wait until
the oil sump has completely emp-
tied to make sure all the oil and
suspended contaminants are re-
moved from the engine.

Figure 5.3.2.C

 Fit oil drain plug and tighten firmly.

Figure 5.3.2.D

 Pour clean engine oil to the speci-

fied level. Refer to “Oil recom-
mendation”.
 Engine oil capacity(oil pan)

Figure 5.3.2.E

 Check the oil level after finished;

refer to “Engine oil check”. And re-
tighten the lubricant oil cap.

 Start engine and let it run at slow

idle for 1 minute. Check for oil
leaks at engine oil filter. Tighten
only enough to stop leaks.

Figure 5.3.2.F

68
 Maintenance

 Replace oil cartridges

Note!
Hot oil and components can cause personal injury. Wear gloves to prevent hot oil or
components from contacting your skin. Do not install the cartridges over tighten.

 Clean the area around the oil car-

tridges and place a proper con-
tainer under the oil cartridges,
Remove the used cartridges and
discard it in a safe place and in
accordance with your local regula-
tions.
 Make sure the gasket from the
used cartridges does not remain
stuck to the cartridges head. Wipe
the oil from the cartridges seat with Figure 5.3.2.G

a cloth.

 Apply a thin layer of oil to the

gasket on the new cartridges.
 Tighten the cartridges by hand until
the gasket contacts the sealing
surface, then tighten it an addi-
tional ¾~1 turn.
 Start the engine and run at idle.
Inspect the cartridges for any oil
leak, and inspect the oil pressure.
If there is leak, retighten the car-
tridges, clean the leak, and then Figure 5.3.2.H

inspect for the leak in idle again.

69
Maintenance

 Clean the air filter(s), replace if needed

Note!
Never start the engine without the air filter as this could cause injury and severe engine
damage.
A dirty and blocked air filter will reduce the amount of air entering the engine which can
cause black smoke and weak power.
Dirty air filter can also lead to early abrasion of cylinder liners and valves, which can
cause excessive oil consumption, black smoke and weak power.
After the air filters are cleaned for 5 times, the air filters should be renewed. Unless that,
the air filters should be renewed every one year or 4000 hours.

Clean the air filters

 Use clean air under 0.5MPa, blow
and sweep the dust on external
filter element from inside to the
outside, and it is forbidden to wash
the filter element with oil or water.

Figure 5.3.2.I

 After cleaning, place a light to

check for damage, pinholes and
worn sections. If any breakage is
found, replace the air filter with a
new one.

Figure 5.3.2.J

70
 Maintenance

Change the air filters

 Release clamps.
 Remove the cover.
 Remove the dirty filter.
 Install new air filter.
 Install the cover and tighten
clamps.

Figure 5.3.2.K

 Replace fuel cartridges

Note!
When handling fuel, make sure there are no flames or heat source in the area. Spilled
fuel can ignite and cause fire. Wipe any spilled fuel completely. Do not allow dirt to enter
the fuel system. Clean thoroughly the area around fuel system component that is dis-
connected. Fit a suitable cover to any disconnected component of the fuel system. Do
not loosen fuel pipes or fittings except what indicated in this manual.

 Clean the area around the fuel

cartridges and place a container
under the fuel cartridges. Remove
the used cartridge and discard it in
a safe place and in accordance
with your local regulations.
 Make sure the gasket from the
used cartridges does not remain
stuck to the cartridges head and
wipe the fuel from the cartridges
seat with a cloth. Figure 5.3.2.O

 Apply a thin layer of oil to the

gasket on the new cartridges. Fill
the new fuel cartridges with clean
fuel via the fuel entry side.
 Tighten the cartridges by hand until
the gasket contacts the cartridges
seat. Then tighten it an additional
¾~1 turn.
 Start the engine and run at idle.
Inspect the cartridges for any fuel
leak. If there is leak, retighten the Figure 5.3.2.P

cartridges, clean the leak, and then

inspect for the leak in idle again.

71
Maintenance

 Check defaults recorded in ECU(if equipped)

 Reading the fault code via thedi-

agnosticsmart. Contact Baudouin
dealer for the diagnostic smart
purchasing and using.

Figure 5.3.2.T

 Refer to "List of fault codes" to find

the text explanation corresponding
to each fault code and you can
determine the current fault.

Figure 5.3.2.U

 Clearing the memory of historical

errors after solving the problems.

Note!
If you encounter electronic con-
trol problems, please contact a
professional Baudouin repre-
sentative to consult;
Refer to the diagsmart operation
manual for the operation of the
diagnostic smart.

72
 Maintenance

5.3.3 M2 Maintenance Operations

M2 maintenance operations include ALL M1 MAINTENANCE OPERATIONS and the follow-

ings:

 Clean the intercooler, air and water side (if equipped)

 Check that the intercooler is not
clogged on the air side and that the
cooling fins are not damaged.
 Carefully scrape away any depos-
its from the cooling fins. Use a
paraffin-based engine cleaner if
necessary.
 Carefully straighten bent cooling
fins using a steel brush or the like.
Figure 5.3.3.A

 Clean the radiator and cooling system

 Clean radiator cooling fins with
compressed air. Cleaning should
be done always in opposite direc-
tion of air flow.

Figure 5.3.3.B

 Check the rocker arm and cross-bar

clearance
 Please contact local Weichai ser-
vice center for valve clearance
adjustment.

73
Maintenance

 Check the battery, battery electrolyte level, battery charger, battery cables
Note！
Clean the top surface of the battery after performing maintenance work. Dust on the
battery may cause short-circuit.
Before inspecting or servicing any electrical component, disconnect the ground cable
from the negative (-) battery to prevent short-circuits and fire.
Do not use flames near the battery. When handling the battery, be careful of sparks
generated by accidental shorting.
If electrolyte is spilled on the eyes, skin or clothes, wash immediately with plenty of
water. If electrolyte enters the eyes, flush immediately with lots of fresh water and see a
physician.

 Check the battery electrolyte level.

Electrolyte evaporates during use
and the fluid level gradually de-
creases. The fluid surface should be
between the LOWER LEVEL and
UPPER LEVEL lines. If the fluid level
is lower, remove the caps and add
electrolyte to the proper level.

Figure 5.3.3J

 Measure the specific gravity of the

electrolyte. If the specific gravity
measured is lower than the minimum
values the battery dealer gives,
charge the battery.

Figure 5.3.3.K

 Check battery cables and connectors for cracks or corrosion. Replace broken terminals,
joints, or cables.

74
 Maintenance

5.3.4 M3/M4 Repair Operations

 Change Belt
Note!
The fan belt idler is under tension. Do not allow your hands to get between the idler and
the belt or the fan hub. Personal injury can result.

For 4M06 belt

 Remove the grid of radiator, and then
loose the fan.

Figure 5.3.5.A

 Use a wrench to hold the belt ten-

sioner. Rotate the idler cap clockwise
to relieve the tension on the idler.

Figure 5.3.5.B

 Remove the fan belt.

Figure 5.3.5.C

75
Maintenance

 Use a wrench to hold the belt ten-

sioner. Rotate the idler cap clockwise
to relieve the tension on the
idler .Install the belt. Make sure it is
fully seated on the pulley grooves.
Belt tension is automatically set. Re-
install the fan and radiator.

 Check the turbocharger

 Disassemble the inlet pipe and ex-
haust pipe from the turbocharger.

Figure 5.3.5.D

 Inspect the turbocharger compressor

impeller blades for damage. Contact
a Baudouin authorized service center
if damage is found.
 Care must be taken to the air filters.
For if the impellor was polluted, the
balance adjusted precisely would be
deviated to cause a vibration that
may cause the stuck or abnormal
wear of the bearing.
Figure 5.3.5.E

 Use a dial indicator to measure the

axial motion (end-to-end), in case
that the clearance to axial direc-
tions exceeds the values below,
replace or repair the turbocharger.

Figure 5.3.5.F

76
 Maintenance
 Measure the radial clearance
(side-to-side) at the compressor
impeller nose using a dial indicator.
In case that the clearance to radial
directions exceeds the values
above, replace or repair the turbo-
charger.

Figure 5.3.5.G

 Replace the Coolant

Note!
For information regarding the disposal and the recycling of used coolant, consult your
Baudouin dealer.
Stop the engine and allow the engine to cool. Ensure that the engine will not start when
the cooling system is drained.
 Stop the engine, add the special
cleaning detergent for engine
cooling system to the old coolant.

Figure 5.3.5.H

 Start the engine, run engine for

15min at idle speed.

 Stop the engine, drain the old

coolant completely to the container
by opening the drain valves of
cooling system and radiator.

Figure 5.3.5.I

77
Maintenance

 Remove the thermostats, fill the

cooling system with clean water,
run engine until it has reached op-
erating temperature for approxi-
mately 20-30 minutes.

 Shut the engine OFF, allow it to

cool to 50°C, and drain the cooling
system. If the water drained is still
dirty, the system must be flushed
again until the water is clean.
 Assemble the thermostats.
 Make sure the radiator drain valves
are closed, fill new coolant. Figure 5.3.5.J

 Check the o-ring of the cooling

systemfiller cap. If the o-ring is
damaged, replace the old cooling
systemfiller cap with a new cooling
system filler cap.

Figure 5.3.5.K

78
 Maintenance

5.3.5 Overhaul Operations

5.3.5.1 Overhaul Information

An overhaul is replacing the major worn components of the engine. An overhaul is a mainte-
nance interval that is planned. The engine is rebuilt with certain rebuilt parts or new parts that
replace the worn parts.
An overhaul also includes the following maintenance:
 Inspection of all the parts those are visible during the disassembly
 Replacement of the seals and gaskets that are removed
 Cleaning of the internal passages of the engine and the engine block.

5.3.5.2 Overhaul (In-Structure)

 Scheduling an In-Structure Overhaul
Generally, scheduling an in-structure overhaul normally depends on the following two condi-
tions:
 200% initial oil consumption
 Fuel consumption rise ≥10%

Each individual condition may not indicate a need for an overhaul. However, evaluating the
three conditions together is the most accurate method of determining when an in-structure
overhaul is necessary.

Periodically measure each of the three conditions. The first measurement should occur during
the engine commissioning. This establishes a baseline for future measurements. Additional
measurements are scheduled at regular intervals in order to determine a schedule for the next
in-structure overhaul.

Note!
These indications do not require an engine to be shut down for service. These indica-
tions only mean that an engine should be scheduled for service in the near future. If the
engine operation is satisfactory, an immediate overhaul is not a requirement.

Note!
The generator or the driven equipment may also require service when the engine
overhaul is performed. Refer to the literature that is provided by the OEM of the driven
equipment.

 In-Structure overhaul
Some components that wear are replaced. The condition of components is inspected. Those
components are replaced, if necessary.
The recommendations of parts for in-structure overhaul is as followed:

79
Maintenance

Clean/ Inspect /Test

 Condition of the cylinder head seating  Oil cooler
in the plane of the cylinder head gasket
Inspect /Replace
 Alternator  Fuel injectors
 Starter  Flywheel ring gear(Apply grease)
 Coolant pump  Fuel injection pump
 Turbocharger
Replace
 Valves/Valve spring/Valve seat/Valve  Rocker arm and shaft
collet/Valve guide/Valve stem seal  The lubricating pipes (rocker arm, tur-
 Thermostatic valves bochargers …)
 Cylinder head gaskets and other nec-
essary gaskets or seal rings
 Cylinder head assemblies
The valves and the valve seats are worn over time. This causes the valves to recede into the
cylinder head. This condition is called valve recession.

In order to determine the wear condition between the valve seat and the valve, it is necessary
to further measure the valve recession. Valve recession is the vertical distance between the
valve bottom face and the bottom plane of the cylinder head.
 Perform sealing pressure test of cylinder heads.
 Measure the valve recession with a depth gauge.
 Check whether the upper and lower end face of valve guide has eccentric wear, dam-
age, etc. Measure inner diameter of valve guide with inner diameter gauge.
 If valve recession and valve guide wearing exceeds the limit, need to rebuild the cyl-
inder.
 Rebuild the cylinder head: replace new valves, valve seats, valve guides, valve stem
seals all together if any of them need to be replaced.
 Grind to ensure the seal ability between valve and valve seat.

5.3.5.3 Overhaul (Major)

Generally, the need for a major overhaul is determined by several factors. Some of those
factors are the same factors that determine the in-structure overhaul:
 300% initial oil consumption
 An increase of crankcase blow by

Other factors must also be considered for determining a major overhaul:

 Power output
 The service hours of the engine
 Reduced oil pressure
 The wear metal analysis of the lube oil
 An increase in the levels of noise and vibration
80
 Maintenance

An increase of wear metals in the lube oil indicates that the bearings and the surfaces that
wear may need to be serviced. An increase in the levels of noise and vibration indicates that
rotating parts require service.

A major overhaul includes all of the work that is done for top overhauls and structure overhauls.
A major overhaul includes additional parts and labor. Additional parts and labor are required in
order to completely rebuild the engine. In some cases, the engine is relocated for disassembly.

For the major overhaul, all of the bearings, seals, gaskets, and components that wear are
disassembled. The parts are cleaned and the parts are inspected. If necessary, the parts are
replaced. The crankshaft is measured for wear. The crankshaft may require regrinding. Alter-
natively, the crankshaft may be replaced.

The recommendations of parts for major overhaul is as followed:

Clean /Inspect /Test
 Oil suction strainer
Inspect/ Rebuild/ Replace
 Camshaft  Flywheel
 Crankshaft  Timing gears clearances
 Engine block
Inspect/ Replace
 Turbocharger  Oil pump
 Fuel injection pump  ECU
 Cylinder head assemblies  Gear
 Intake manifold  Gear shaft
 Wiring harnesses  Push rod
 Connecting-rod  Tappet
 Fans
Replace
 Piston /Piston rings/Cylinder lin-  Camshaft thrust plate
er/Connecting-rod bearings  All gaskets and seals
 Main bearings  Crankshaft thrust plate set
 Injectors  Piston nozzle
 Rocker arm  Crankshaft front and rear seals
 Rocker arm shaft  Damper and fixing screws
 Thermostatic valves  The bolts of turbocharger, main bear-
 Exhaust manifold ings, connecting-rod, exhaust manifold,
 Camshaft bearings timing gear, cylinder heads, flywheel,
 All gaskets or seal rings and flywheel cover

81
Maintenance

5.4 Storage Protection Instruction

5.4.1 Necessity of Anti-rust Protection

If your engine is out of operation and using for a period of time, then precautions should be
taken to protect your engine from damage and to ensure proper operation when you
re-operate the engine.

The recommendations indicated below are designed to prevent damage to the engine when it
is withdrawn from service for a prolonged period. Use these procedures after the engine is
withdrawn from service. Where necessary protect the engine against frost damage.

5.4.2 Storage Environment Requirement

If the engine is placed in storage area, the following precautions should be taken to protect it.
 Equipment must be kept clean.
 Store indoors, cover it with a VCI plastic bag.
 Keep the engine covered to avoid airborne dust and dirt.
 Cover the ventilation openings, conduit connections, etc., to prevent entry of rodents,
snakes, birds, insects, etc.

 Keep the equipment dry.

 Store in a dry indoor area.
 Temperature swings should be minimal to prevent condensation.
 If stored in an unheated or damp building, space heaters will be required to prevent in-
ternal condensation.
 Apply a rust inhibitor for unpainted flanges, shafts, drive discs, and fittings.
 Check insulation resistance of all windings before starting the engine. Dry out the wind-
ings if reading is low.

5.4.3 Preparation before Storage

 Clean the engine for dirt, rust, grease, and oil. Inspect the exterior. Paint the damaged
paint area with good quality paint.
 Remove the dirt from the air cleaner(s). Check all seals, gaskets, and the filter elements
for damage.
 If the engine is stored outside, cover it with a waterproof canvas or other suitable protec-
tive material and use a strong waterproof tape.

5.4.4 Instructions for Short-Term Storage

 Up to one week
 No special treatment is necessary.
 Just clean the area around the engine body.

82
 Maintenance

 Up to three months
Each week operate the engine until the normal temperature of operation is reached. If the
engine is not going to be operated, turn the crankshaft by hand, in the normal direction of ro-
tation (anti-clockwise as seen on the flywheel), a minimum of three revolutions.

5.4.5 Necessary Materials

 Calibration oil
Calibration Oil is a low viscosity mineral oil-based test fluid.
Calibration Oil is a calibration and storage oil for diesel fuel system. Rust preventative proper-
ties of this oil ensure proper functioning of the equipment in normal conditions even after one
year storage, without cleaning the equipment after calibration.

Safety protection is recommended while using the calibration oil, such as barrier cream or
rubber gloves.

 VCI oil
Volatile corrosion inhibitor (VCI) provides liquid and vapor protection to ferrous metal surfaces
against corrosion caused by moisture. In a closed compartment, protection is either by direct
contact with VCl oil or by contact with VCl vapors. Contact your local supplier for similar type of
oil.

VCI oil can be used in all tanks, engine, fuel tank, hydraulic tank, power steering tank, trans-
mission, differential, and other components. The inhibitor is an oil stabilizer and rust preven-
tive.

For correct use of VCl oil, the engine must be sealed when stored. VCI oil is so volatile that
any opening left unsealed will allow the vapors to escape, causing the engine to lose protec-
tion.

Note !
 VCI oil should not be used full strength on non-ferrous metals where the inhibitor
will have direct, prolonged contact.
 The inhibitor can be used in combination with any petrochemical. Apply by using
a spraying or fogging pattern. The VCI oil must be diluted according the instruc-
tion of suppliers.

VCI oil cleaning method

 Drain the VCI oil from the engine.
 Refill standard-compliant engine lubricating oils. For lubricating oil, please refer to the
manual “Fluids RECOMMENDATIONS”.
 Operate the engine for 5 minutes at low idle rated speed.
 Drain the oil completely and refill new lubricating oil.

83
Maintenance

 Sprayer
Load the VCI oil dilution into the sprayer, then can be used to prepare the engine for storage.
Change the nozzle adjustment to provide either a spray or a fog pattern.
VCI oil dilution: mixture of 50 percent VCI oil and 50 percent engine oil.

 Plastic bag
Use ultraviolet light resistant plastic bags. The bag must have a minimum thickness of 0.10
mm (0.004 inch) if the bag is filled with Volatile Corrosion Inhibitor (VCI) oil.

 Waxed paper
Wax paper is a surface-coated wax that has excellent water and oil resistance.
Wrap parts and sealing to prevent rust.

 Adhesive tape
Use a sealing tape with appropriate adhesive properties. DO NOT use duct tape because duct
tape gets loosen over time. Rolls of sealing tape that are 2 inches wide are recommended.

An appropriate quality sealing tape is available from the following suppliers: 3M Product In-
formation Center.

 Biocide
Diesel Fuel Biocide is used to prevent the growth of small organisms in the diesel fuel; use
diesel fuel biocide such as Biobor JF or equivalent.

5.4.6 Long Term Storage（More Than Three Months）

 Lubricating oil system

Drain and replace the crankcase oil and change the oil filters.
Add VCI oil to the crankcase at the rate of 3 to 4 percent by the volume of the crankcase. Or
use special engine rust-proof oil，such as Houghton Ensis Engine Oil 30、Shell Rimula R6lm,
or other equivalent effects product, please follow the supplier's instructions.

Note!
If the engine crankcase is full, drain enough engine oil so the mixture can be added.

 Coolant system
Drain the coolant and flush the cooling system, such as engine blocks, separate circuit af-
ter-coolers, and other related components. It is not necessary to have engine stored for less
than three months. However, for extended storage periods of three months or longer, it is
recommended that the cooling system to be drained, flushed, and refilled. Refill with appro-
priate coolant.

Recommend Total Glacelf Auto Supra concentrates、Basf Glysacorr P113 concentrates, or

other equivalent effects product, please follow the supplier's instructions.

84
 Maintenance

Note !
 If the stored engine is subjected to below freezing temperatures, completely drain
the freshwater system. Drain the system by removing the drain plugs from the
engine block, oil cooler, heat exchanger body, and radiator.
 The mixture must NOT contain less than 50% inhibited ethylene glycol or propyl-
ene glycol and may contain up to 70% by volume.

Fresh Water Systems

Drain the coolant from cooling system and thoroughly flush with the clean water. The system
then should be refilled with mixture of clean water and any of the coolant preservative con-
taining VCI. If the storage is less than three months, drain mixture of clean water and any of
the VCI coolant from cooling system after finished running of the engine.

For clean water, please refer to the manual” Fluids RECOMMENDATIONS Diesel”.

Raw Water Systems

Completely drain the raw water system by removing all the drain plugs from the raw water
pump, water shield manifolds, heat exchanger bonnets, and aftercooler. After the system has
been drained, inspect all zinc plugs (normally painted red) for corrosion damage.

Note!
To ensure complete drainage and evaporation during storage, DO NOT install the drain
plugs and zinc plugs. Place all removed plugs in a cloth bag and fasten the bag to the
engine for storage.

Caution!
When finished all above operations of lubricating oil system and coolant system, then
start the engine for 5 minutes at low idle rated speed.
Turn off the engine and wait about 30 minutes to get it cooled completely, then make
operations as follows.

 Fuel system
Calibration oil
Calibration oil is the preferred choice as a preservation fluid because the calibration oil con-
tains Rust and Oxidation inhibitors.
Recommend Castrol Calibration Oil 4113、SRS Schmierstoff Vertrieb GmbH Calibration Fluid、
Shell V-Oil1404, or other equivalent effects product, please follow the supplier's instructions.

Fuel filter
Remove the fuel from the secondary fuel filter housing or empty and reinstall the spin-on fuel
filter element to remove any dirt and water. Drain the fuel injection pump (sleeve metering
only).Clean the primary fuel filter. Fill with calibration oil. Install the primary fuel filter and op-
erate the priming pump. This will send clean oil to the secondary filter and engine.

85
Maintenance

Fuel tank
Open the fuel tank drain valve and allow any water or dirt to drain from the fuel tank. Apply a
VCI oil of 30 ml per 30 L (1 oz per 7.50 gal) of fuel tank capacity to prevent rust in the fuel tank.
Add 0.15 ml per L (.02 oz per 1 gal) of commercial biocide such as Biobor JF or an equivalent
to the fuel.

Fuel nozzle and spark plug

Remove the fuel nozzles or spark plugs and apply 30 ml (1 oz) of VCl oil mixture (50 percent
VCI oil and 50 percent engine oil) in each cylinder.
Use a bar or turning tool to rotate the engine slowly to put the oil on the cylinder walls. Install all
the fuel nozzles or spark plugs and tighten to the correct torque.

 Intake and exhaust system

Air filter
Remove the air filter elements. Seal the air filter inlets, with VCI plastic bag and adhesive tape.
Use the starter to drive the engine, but no fuel. Then use a sprayer to add VCI oil dilution into
the air inlet and turbocharger inlet, multiple times, total 60s.

Exhaust openings
Use a sprayer to apply VCI oil dilution into the exhaust openings. The minimum application
rate is 5.5 ml per L (3 oz per 1000 cu in) of engine displacement. Seal the exhaust pipe, in-
cluding any drain holes in the muffler.

Vents
All vents i.e. engine inlet pipe, exhaust pipe, air cleaner inlet, coolant inlet & outlet, crankcase
breather, the crankcase breather and all other openings etc. must be carefully sealed with VCI
plastic bag and adhesive tape.

Note !
VCl oil mixture can also be added to the inlet by removing the plug for checking tur-
bocharger boost pressure. The minimum application rate is 5.5 ml per L (3 oz per 1000
cu in) of engine displacement.

 Electrical system
Battery
If battery is provided for engine starting, it should be disconnected and stored in a cool, dry
place after ensuring electrolyte level (refill with distilled water if necessary). It is recommended
to recharge the battery once in a month.

Starter
Clean the electric starter and wiring harness, keep them dry, then cover the alternator in
moldable waxed paper, and seal with adhesive tape.
Alternator

86
 Maintenance
Cover the alternator in moldable waxed paper, and seal with adhesive tape.

Engine wiring harness

Clean the engine wiring harness, and keep it dry.

 The others
V-belt
Loosen all the belts (tension, fan, alternator, etc.)

Flywheel
Spray a thin amount of VCI oil mixture on the flywheel, ring gear teeth, and starter pinion. In-
stall the covers to keep in the VCI vapors.

Note !
Use a VCI plastic bag to cover the engine. Ensure the engine cover is secure, but loose
enough to allow air to circulate around the engine to prevent damage from condensa-
tion, and put some desiccants, then seal with the adhesive tape.
Attach a tag to the engine with a notation of the date that the unit was preserved.
Remove the waterproof cover every three months and check the engine for corrosion. If
the engine has signs of corrosion at the check period, repeat the protection procedure.

5.4.7 Removal from Storage

Refer to the appropriate section for detailed services listed below or have your authorized
servicing dealer or engine distributor perform services that you may not be familiar with.
 Remove all the outside protective covers. Unseal all the openings in engine and remove
the covering from electrical systems.
 Change the oil and oil filters. Then drain the oil and refilled with new lubricating oil. For
lubricants, please refer to the manual” Fluids RECOMMENDATIONS”.
 Drain the VCI coolant from the engine. Use clean water to flush any compartment that
contains VCI coolant to remove all residuals. Then drain the clean water and refill new
coolant. For coolant, please refer to the manual” Fluids RECOMMENDATIONS”.
 Replace the fuel filter elements and fill the fuel tank with diesel fuel.( Gas machine does
not need to do this operation)
 Check the battery level.
 Check the condition of the fan and alternator belts. Replace the belts, if necessary.
Tighten the belts as specified in the Operation & Maintenance Manual.
 Check the engine harness if the harness is not aging. Replace the harness, if necessary.
 Remove the batteries from storage. Install batteries (fully charged) and connect the
electric wires.
 Install fan/alternator poly-vee belt if removed earlier.
 Perform all appropriate pre-starting checks.
 Please assemble all the other parts back to engine.

87
Maintenance

5.4.8 Initial Running after Storage

The purpose of this operational check is to ensure that the correct pressures and temperatures
are maintained in the lubrication, cooling, and fuel systems. Also, these operation ensures that
any leaks are corrected.
To ensure a safe operation, use the following procedure:
 Before starting the engine, use hand oil pump or electric pre-supply pump to establish
the oil pressure of the engine.
 Crank engine for 20 seconds with starter (do not allow the engine to start). Wait 2
minutes and crank the engine for additional 20 seconds to assure bearing surfaces are
adequately lubricated.
 Start the engine and run at low idle and no load for several minutes. Warm up carefully
and check all gauges before placing engine under load.
 Operate the engine for 10 minutes at low idle rated speed.
 Operate the engine for 15 minutes at half rated load and 3/4 rated speed.
 Operate the engine for 30 minutes at full rated load and full rated speed.
 Check regularly for leaks such as oil, coolant, and fuel during the first few hours of op-
eration. Repair any leaks as soon as detected.
 Check all kinds of indicators to confirm that there is no abnormality, if there are any ab-
normal parameters, please handle it promptly.

88
 Appendix

6. Appendix
6.1 Coolant Recommendation

The coolant ensures the best efficiency of the cooling system and protection against corrosion
(chemical and galvanic). It improves also boiling temperature, resistance to rust and avoids
scale deposit formation.

 The coolant used in Baudouin engines should meet the ASTM D6210 standard, and the
coolant used in Baudouin engines should not contain 2-ethylhexanoate, which has
compatibility problems with silicone rubber.
 Do not use a commercial coolant that only meets the ASTM D3306 specification. This
type of coolant is made for light-duty engine applications.
 The coolant recommended in „Fluids Manual ‟ is preferred for Baudouin engines.

Important Note !
45% glycol content is the minimum required values to maintain the best boiling tem-
perature. Do not use ethylene glycol content that exceed 60%.

89
Appendix

6.2 Lubricant Recommendation

It is important to comply with the oil drain and filter change intervals to guarantee the proper
operation of your S. I. Moteurs Baudouin equipment.

Lubricant grade for the engine

Present lubricant certification process according to API and ACEA standards is adequate to
guarantee adequate quality and performances.
Therefore S. I. Moteurs Baudouin requires use of following lubricants:

API CI-4 or ACEA E7 15W40

 Quality Grade
Lubricating oils are differentiated according to their performance and quality class. Oils
with comparable specifications can be used.
Approved Oil
Baudouin Engine Off-road stage Ⅱ Off-road stage Ⅲ
API CI-4 CI-4
ACEA E7 E7
 Viscosity
As the viscosity of lubricating oil is de-
pendent on temperature, the choice of Viscosity selction based on ambient
SAE grade should be governed by the temperature
ambient temperature prevailing at the
engine operating site. Should the tem-
perature fall temporarily below the limits
of the SAE grade selected, cold
star-ting may be affected but the engine
will not be damaged. In order to keep
wear to a minimum, do not exceed ap-
plication limits for extended periods of
time. Synthetic lubricating oil features
an improved temperature and oxidation
stability.

90
 Appendix

Viscosity and temperature properties specification

High-temperature and
Low-temperature
Viscosity（100℃） high-shear viscosity
Project kinematic viscosity
6 -1
Pour point/℃ ≤
/mm²/s （150℃, 10 s ）
/mPa·s(℃）≤
/mPa·s ≥
Test method SH/T 0618
SH/T 0703
GB/T 265 SH/T 0751
GB/T 6538 GB/T 3535
ASTM D-445 CECL-36-T-84
ASTM D5293 ASTM D 97
/ISO 3104 ASTM D4741-87
ASTM D4582-95
Viscosity grade ASTM D4624-93

0W-20 6200(-35) 5.6～<9.3 2.6

0W-30 6200(-35) 9.3～<12.5 2.9 -40

0W-40 6200(-35) 12.5～<16.3 2.9

5W-20 6600(-30) 5.6～<9.3 2.6

5W-30 6600(-30) 9.3～<12.5 2.9

-35
5W-40 6600(-30) 12.5～<16.3 2.9

5W-50 6600(-30) 16.3～<21.9 3.7

10W-30 7000(-25) 9.3～<12.5 2.9

10W-40 7000(-25) 12.5～<16.3 2.9 -30

10W-50 7000(-25) 16.3～<21.9 3.7

15W-30 7000(-20) 9.3～<12.5 2.9

15W-40 7000(-20) 12.5～<16.3 3.7 -25

15W-50 7000(-20) 16.3～<21.9 3.7

20W-40 9500(-15) 12.5～<16.3 3.7

20W-50 9500(-15) 16.3～<21.9 3.7 -20

20W-60 9500(-15) 21.9～<26.1 3.7

91
Appendix

6.3 Fuel Recommendation

Improper fuel additive usage may cause damages to fuel injection equipment of diesel en-
gines.

 Quality Grade
Use commercially available diesel fuel with less than 0.35% Sulphur content. If the sulfur
content is higher than 0.5%, oil change intervals should be halved.
The following fuels can be used on Baudouin engine:
--- European standard EN 590.
--- ASTM D-975
--- BS 2869 Part 1 Class A 1 standard

 Winter-grade Fuel
When temperature is low and the fuel you currently use is not proper, there will be wax in the
fuel. Wax can clog the fuel system and reduce engine performance. If the ambient temperature
is less than 0℃，winter-grade fuel should be used.
When temperature is below -20℃, please choose proper diesel fuel that can be used in this
temperature range.
For more information about fuel selection, please consult your local fuel supplier.
The pour point of diesel fuel should be at least 6℃ lower than the minimum ambient temper-
ature. The proper pour point is essential for engine start-up and running performance.
If diesel fuel with proper pour point is unavailable, Baudouin recommends using fuel heater to
resolve the wax problem. Fuel heater is a low cost solution in most application.

92
 Appendix

6.4 Common Faults and Troubleshooting

6.4.1 Troubleshooting

 Engine Turns, But It Does Not Start

Table 6-1 Engine turns, but it does not start
Problem Cause Remedy
(1) No fuel supplied to fuel injection pump
Bleed air from fuel filter and
fuel feed pipes, and inspect
a) Air trapped in fuel supply
each part for damage and air
system
leaks. Disassemble and re-
pair, if necessary.
b) Empty daily fuel tank Add fuel.
Disassemble and clean, or
c) Fuel filter is blocked
replace filter element.
d) fuel feed pipe is blocked Clean inside of pipe.
e) Fuel is not supplied due to Disassemble and inspect, or
malfunction of fuel feed pump replace fuel feed pump or
or drive unit drive unit.
f) Electronic governor problem Refer to electronic governor
for mechanical pump diagnosis.
(2) Fuel supplied to fuel injection pumps
a) Loose fuel injection pipe and If loosened, tighten.
A: Engine emits hardly low injection pressure
any exhaust smoke Inspect control link. If there is
a fuel lever linkage problem,
b) Seized or damaged parts in
disassemble and repair. Re-
fuel injection pump
move cam chamber cover,
Malfunction of fuel lever
and operate by hand. If parts
Control rack does not move
are defective, disassemble
and repair, or replace.
c) Seized plunger Replace, if defective.
Inspect two-way delivery
d) Clogged two-way delivery
valve, and disassemble and
valve
clean.
e) Broken plunger spring Disassemble and repair, or
replace if defective.

93
Appendix

Problem Cause Remedy

Check relation of movement
a) Fuel lever does not open with fuel lever, and disas-
fully semble and repair if defec-
tive.

b) Seized tappet in fuel injec- Check for uneven movement,

tion pump and disassemble and repair,
or replace.
c) Worn tappet roller or cam-
shaft in fuel injection pump
Replace, if worn.
(reduced amount of injected
fuel)
d) Seized or worn plunger in
B: Engine emits small fuel injection pump, worn Check for uneven movement,
amount of exhaust broken plunger spring (re- and disassemble and repair,
smoke. (Check the cause duced amount of injected or replace.

of insufficient injected fuel. fuel)

e) Loose tightening screw of
Check all items in A-(1)
control rack of fuel injection Tighten screw.
and (2)- b, and also check
pump
items at right.)
f) Defective oil sealing perfor-
mance of two-way delivery Disassemble and repair, or
valve, or broken two-way de- replace.
livery valve spring
Use fuel with viscosity suita-
g) Fuel viscosity too high to ble for ambient temperature.
allow smooth flow If fuel quality is improper,
change fuel.
Check leak-off pipe for
h) Large amount of fuel leaks amount of fuel leaks, check
from fuel injection nozzles, with nozzle tester, and re-
and insufficient injected fuel place defective parts if nec-
essary
(1) Improper fuel injection timing
Inspect camshaft drive sec-
C：Engine emits large
tion, and adjust fuel injection
a）Malfunction of camshaft drive
amount of exhaust timing correctly.
smoke. (Check the cause b）Deviation of fuel ignition
of ignition failure despite timing due to worn fuel in-
sufficient amount of in- jection pump tappet roller or
Replace if worn.
camshaft cam
jected fuel.)

94
 Appendix

Problem Cause Remedy

(1) Improper fuel injection timing
Inspect camshaft drive sec-
tion, and adjust fuel injection
a）Malfunction of camshaft drive
timing correctly.
b）Deviation of fuel ignition
timing due to worn fuel in-
jection pump tappet roller or
Replace if worn.
camshaft cam

(2) Poor spray condition of fuel injection nozzles

a）Sticking of needle valve in Check with nozzle tester, and
fuel injection nozzle, or im- disassemble and repair, or
proper valve seat sealing replace.
Using nozzle tester, adjust
b）Low fuel injection nozzle adjustment screw so that fuel
valve opening pressure is injected at specified valve
C：Engine emits large
opening pressure.
amount of exhaust c）Damaged or broken nozzle Replace if damaged.
smoke. (Check the cause spring
of ignition failure despite Clean mounting surfaces of
d) Large amount of fuel leaks
nozzle and holder. Replace if
sufficient amount of in- from nozzle
necessary.
jected fuel.)
(3) Insufficient compression pressure (cylinder internal temper-
ature does not reach ignition temperature)
If starting air pressure is low,
increase pressure.
If engine oil viscosity is high,
a）Inadequate rotation speed heat oil or change oil to one
with appropriate viscosity
Repair if there are other ab-
normalities.
b）Inlet/exhaust valve not Disassemble and repair by
contacting valve seat lapping valve in valve seat, or
properly
replace if necessary.
Check for sticking of valve
and valve guide, incorrect
c）Valve remaining open tappet assembly, and valve
clearance, and correct ab-
normalities if necessary.

95
Appendix

Problem Cause Remedy

d）Leaking of compression
Disassemble and repair, or
pressure due to worn cylinder
replace if necessary.
liners or sticking of piston rings
Check for gas leaks, and
e）Leaking of compression
tighten cylinder cover
pressure from cylinder cov-
properly. Repair gas seal
er
surface or replace gas seal
ring, if necessary.
(4) Inappropriate fuel
Drain fuel and check. Change
a）Inappropriate fuel or water in
to higher- quality fuel, if nec-
fuel
essary

 Engine Does Not Turn

Table 6-2 Engine does not turn
Problem Cause Remedy
a）Malfunction of starting Inspect starting valve, and
valve repair or replace
A：Malfunction of starting air
b）Starting air pressure lower Check air tank pressure, and
system than specified increase pressure if low

a）Seizing of moving parts in Disassemble and inspect

engine pistons, connecting rods,
crankshaft, camshaft, bush-
ings of timing gear and oth-
ers, inlet and exhaust valves,
B：Malfunction of mechan-
etc., and repair.
ical engine parts
b）Deviation of timing due to
incorrect engine assembly Disassemble and repair.
Pistons are hitting valves
c）Viscosity of engine oil too Change oil to one with lower
high, or clotted oil viscosity.

96
 Appendix

 Engine Output is Low

Table 6-3 Engine output is low

Problem Cause Remedy

(1) Tendency of engine moving parts toward seizing
a）Tendency toward seizing Check abnormal heating of
due to insufficient clear- parts listed in B-a in Table
ances of engine parts 6-2, and repair defective
parts
A：Engine emits small
b）Inadequate lubrication Check oil level, oil pressure
amount of exhaust(Engine and oil viscosity, and add,
output and speed are inad- adjust or replace oil, and also
equate due to insufficient clean lubricating system if
there is oil clogging
injected fuel.)
(2) Insufficient amount of fuel supply
a）Clogged fuel system or Clean or replace. (Refer to A
loose pipe in Table 6-1.)
b）Malfunction of fuel supply Clean or replace. (Refer to B
or injection system in Table 6-1.)
(1) Engine knocking and excessive white smoke when engine
is cold
Injection timing too advanced Correct. (Refer to C-(1) in
Table 6-1.)
(2) Poor combustion due to low compression pressure

Check for valve, valve guide

a）Valve remaining open. sticking and valve clearanc-
es, and repair.
b）Inlet/exhaust valve not Disassemble and correct by
contacting valve seat proper- lapping valve in valve seat, or
B：Engine emits excessive ly replace if necessary.
white exhaust smoke Disassemble and repair, or
c）Broken inlet/exhaust valve
replace if necessary.
spring

d）Leaking of compression Disassemble and repair, or

pressure due to worn cyl- replace if necessary.
inders or sticking of piston
rings.
(3) Poor fuel condition (water Open drain cock and check
in fuel) fuel. Drain water or change
fuel.

97
Appendix

Problem Cause Remedy

(1) Fuel injection timing too Correct. (Refer to C-(1) in
retarded Table 6-1.)
(2) Uneven fuel injection among cylinders
(Poor combustion condition, unstable rotation with knocking)
a) One or more worn tappet Replace if worn
rollers or cams on cam-
shaft in fuel injection
pumps causing deviation of
fuel injection timing
b) One or more plunger Disassemble, repair or re-
springs seized, worn or place
broken
(3) Poor spray condition of Refer to C-(2) in Table 6-1
C: Engine emits excessive
some fuel injection noz-
black exhaust smoke
zles
(Exhaust temperature of
cylinders with poor fuel
spray condition may
become high.)
(4) Poor combustion due to insufficient inlet
a) Malfunction of turbo- Disassemble and repair, or
charger (damage of vanes, replace if necessary
seizing of bearing, etc.)
b) Malfunction of in- Refer to B-(2) in Table 6-3
let/exhaust valve
c) Air cleaner clogged with Disassemble and clean, or
dust replace if necessary

 Engine Knocks
Table 6-4 Engine knocks
Problem Cause Remedy
A：Engine knocks slightly Refer to C-(1) in Table 6-1
Fuel injection timing too re-
and emits black exhaust
tarded
smoke
B：Knocking is severe, and Fuel injection timing is too
exhaust smoke is white advanced Refer to C-(1) in Table 6-1
Uneven fuel injection among cylinders
a)Excessive fuel injection in a)Excessive fuel injection in
C：Knocking is severe in some cylinders some cylinders
certain cylinders b) Fuel injection timing too b) Fuel injection timing too
advanced in some cylinders advanced in some cylinders

98
 Appendix

Problem Cause Remedy

D：Ignition retardation oc- Improper spray of fuel by fuel injection nozzles
curs and results in simulta- Fuel is not sprayed in prop- Refer to C-(2) in Table 6-1
neous ignition to cause se- er condition in some cylin-
vere knocking. ders
E：Ignition retardation oc- Low engine compression
curs frequently and results Amount of intake air is low Refer to C-(3) in Table 6-1
in simultaneous ignition to in some cylinders
cause severe knocking
Engine oil rising above pistons
a）Oil level too high in Discharge oil to appropriate
F： Injection of fuel gener- crankcase level.
ates knocking, and engine b）Worn piston rings or Check crankcase breather
emits large amount of black sticking of piston rings, pipe for gas leak, and re-
or gray exhaust smoke. resulting in inadequate place if there are defective
When oil does not rise, en- scraping of oil parts.
gine does not knock se- c）Excessive clearance Check crankcase breather
verely and emits bluish between cylinder and pipe for gas leak, and re-
white exhaust smoke piston place if necessary.
d）Engine oil viscosity too Change to high-quality oil
low with higher viscosity.
a) Excessive connecting rod Disassemble and inspect,
bearing clearance, or bear- and repair or replace if
ing metal flaking necessary.
G：Abnormal noise pro-
Disassemble and inspect,
duced when injection is b) Loose connecting rod cap
and repair or replace if
stopped suddenly and en- tightening bolts
necessary.
gine is allowed to rotate by
Check crankcase breather
inertia c)Excessive clearance be-
pipe for gas leak, and re-
(engine mechanical failure) tween cylinder and piston
place if necessary.
d)Piston hitting foreign item
Disassemble and inspect.
fallen inside cylinder
H：Low compression tem-
perature and retarded igni- Operate engine until it
tion cause severe knocking, Engine too cold warms up before increasing
especially after engine engine speed
starts in cold weather

99
Appendix

 Engine Produces Large Amount of Smoke While in Operation

Table 6-5 Engine produces large amount of smoke while in operation
Problem Cause Remedy
(1) Severe knocking
Fuel injection timing too ad-
Refer to C-(1) in Table 6-1.
vanced
(2) Knocking produced only in cylinders with insufficient com-
pression
Low engine compression Refer to C-(3) in Table 6-1.
(3) Improper fuel
Open drain cock and check.
a Water contained in fuel Remove water or change
fuel.
A：Engine emits excessive
(4) Other
white exhaust smoke
a）Lange amount engin e oil Inspect and repair or replace
rising above pistons as described in F in Table
6-4.
Inspect temperature regula-
b）Engine too cold, resulting
tor, and adjust it properly to
in poor combustion
prevent overcooling.
Unburned oil is trapped in
c）Engine operating too long exhaust pipe. White smoke
with no load stops after engine is operated
under load.
(1) Minor knocking
a Injection timing too retarded Refer to C-(1) in Table 6-1.
(2) Other
Check if fuel injection pump
a）Excessive amount of in-
rack set screw or bolt is
jected fuel
loose, and repair.
Inspect, and repair or replace
as described in C-(2) in Table
b）Fuel injection not uniform 6-3
B：Engine emits excessive
black exhaust smoke.
Inspect, and repair or replace
c）Improper spray of fuel by as described in C-(2) in Table
fuel injection nozzles 6-3
Inspect, and repair or replace
d）Low engine compression as described in C-(2) in Table
6-3
e）Large amount engine oil Inspect and repair or replace
rising above pistons as described in F in Table
6-4.
100
 Appendix
 Engine Operates at High Speed and Does Not Stop
Table 6-6 Engine operates at high speed and does not stop
Problem Cause Remedy
Link between fuel increase/
Check if link returns without
decrease lever and governor
catching, and repair if nec-
failing to return smoothly to
essary.
original position
Fuel injection pump does not
Repair if rack does not move
set to no-injection condition
a）Loose control link lever in connection with governor
lever.
b）Sticking of rack disallowing Check rack for smoothness,
its return to original position and disassemble and repair.
 Malfunction of Lubricating System
Table 6-7 Malfunction of lubrication system
Problem Cause Remedy
Check oil level gage, and add
a) Engine oil level too low
oil if level is low
b) Engine oil viscosity too Change oil to one with ap-
high for smooth pumping of propriate viscosity
oil (Especially when tem-
perature is low)
Remove pipe from pump dis-
charge side, and check oil
c) Clogged oil pump suction
discharge. If no oil is dis-
A： Oil pressure does not side or strainer screen
charged, disassemble, clean
rise immediately after start
and repair, or replace
Repair or replace defective
d) Malfunction of regulator
parts, such as broken valve
valve
spring and seized valve
e) Clogged oil filter element Disassemble, clean, replace

Disconnect oil pressure gage

f) Defective oil pressure gage
pipe. If oil pours out, replace
oil pressure gage
B：Oil pressure drops a) Clogged oil filter element Disassemble, clean, replace

gradually during operation Oil temperature rises and

causes oil pressure to drop.
b) Engine oil viscosity too low
Change oil to one with higher
viscosity
Engine is overheated. Do not
c) Abnormally high oil tem-
operate engine until oil tem-
perature
perature is low
d) Tendency toward bearing Disassemble, repair
seizing
101
Appendix

Problem Cause Remedy

C：Oil pressure abruptly a) Damage bearing causing Disassemble and repair

drops during operation and increased oil leaks

b) Cracking in engine oil pas- Check for leaks, and repair or
remains there
sage, or oil leakage from replace defective parts
joint
D：Oil pressure fluctuates Engine oil level too low, Check oil level gage, and add

suddenly during operation causing air to mix into oil oil if level is low

 Diagnosis of electronic governor

Problem Cause Remedy
Push actuator handle check
engine will start or not. If it
can start, check it according
to the following methods. If it
a) Actuator or controller not
cannot start, check diesel
work well
engine or the fuel pump.
Check whether there is 10V
output for 5 and 14 terminal; if
not, replace the controller.
Check whether the controller
5 and 6 terminals have 24V
DC power input, and there is
a power indicator at the lower
right corner. If not, connect
directly to the battery. The 5
A： Engine not start terminal connect the negative
pole of the battery, and the 6
terminal connect the positive
pole of the battery.(The volt-
age of the battery shall not be
lower than 18V for 24v bat-
tery at the starting moment,
and the voltage of 12V shall
not be lower than 10V for 12v
b) Battery is low battery );
3, 4 terminal connect speed
sensor cable, start the en-
c) Speed sensor installation gine, when the motor running,
problem the ac voltage of 3, 4 terminal
is 4 v, if not, remove the
speed sensor,clean the front

102
 Appendix

part of the sensor, measuring

the resistance of sensor is
300-1000 Ώ, then install the
sensor again.

Detection controller, 1, 2 ter-

minal: remove 1, 2 terminal
connection, measuring re-
sistance (actuators) between
d) Speed sensor connection 1.5-5 Ώ (controller output
problem voltage is 9 v after start).If
not, please check whether
the actuator cable is con-
nected well or replace a con-
troller.
e) Actuator problem In the case that the diesel
engine does not start, turn on
the switch, remove the wire of
the 1,2 terminal and connect
to the 5,6 terminal for a short
time (1 to 5 to 2 to 6), and the
actuator handle will move
from zero fuel level to the
maximum fuel level. If it does,
replace the controller.If not,
the actuator needs to be re-
placed.
If the “idle”, “speed” and
“starting fuel” of the speed
controller are set too low, it
will also cause failure to start.
Adjust the starting fuel to 3 o
f) Setting problem
'clock and the idle and speed
potentiometer to the middle
position. If the starts suc-
cessfully, please reduce the
speed potentiometer appro-
priately to avoid overspeed
B：There is no “idle” a) Switch problem 7 and 12 terminal of the con-

or ”rated” speed troller are idle and rated

speed transfer switches.
When 7 and 12 terminal are
connected to each other, it is
idle speed and disconnected

103
Appendix

to rated speed, short circuit

can be used to test: after
starting at idle speed, dis-
connect 7 and 12 terminal to
see if there is rated speed or
idle speed. If there is rated
speed, the switch of rate/idle
damage, replace the part. If
there is still no rated speed,
replace controller. 7 terminal
for D, the voltage of 7 termi-
nal and 5 terminal is 0 V .If it
is greater than 0 v, ,this
means that the rated/idle
speed switch or connection
have problem, this caused no
rated-speed (pay attention to
6 terminal is very close to 7
terminal, if the two terminal
touch together, will cause no
idle speed), the voltage of 7
terminal to 12 terminal is 0V
when idle speed, 4 v when
rated speed.
If the “speed” potentiometer
is adjusted too low, it will also
cause no rated speed; When
the 7 and 9 terminal are not
connected to trimmer poten-
tiometer, they must be con-
nected or will lead to the
b) Setting problem speed unstability. 7 terminal
is D, the voltage of 7 terminal
and 5 terminal are 0V, when
the potentiometer resistance
is 0 Ώ , the voltage of 7 and 9
terminal >3V, when there is
resistance value, the voltage
of 7 and 9 terminal<3V.
For speed unstability (idle
speed unstability, rated
speed unstability and speed
unstability with load), adjust
the rated speed stability first-

104
 Appendix

ly, under the condition of sta-

bility at rated speed, adjust
the idle speed stability. Adjust
the “gain” and “stability” and
note the adjusting range ,
refer to the Electronic Gov-
ernor chapter. (in special
case to adjust the perfor-
mance with load firstly).
Detect and clean speed
sensor and reinstall it as re-
quired.
Check potentiometer：
C：Unstable speed a) Setting problem connect 7,9 terminal and
confirm the potentiometer is
damage or not.

b) Battery problem Check the battery voltage

should be 24-30V;
c) Controller or actuator Test without load, if the speed
problem is still not stable, please re-
place the controller or actua-
tor.
d)Engine problem If engine speed is stable
without load, but not stable
when with load, please adjust
“stability”and“gain”again.
If not work, please check en-
gine itself.

Special Attention: the 7 and 9

terminal of the controller must
be connected with the trim-
mer potentiometer or con-
nected with each other di-
rectly. If not, it will cause the
speed unstability, (the rated
speed will rise when connect
directly to each other, so
need to rotate “speed”
potentiometer counterclock-
wise 2 turns, in case of
overspeed ).Also note that
the battery voltage should not

105
Appendix

be too low.
First adjust the “gain”
potentiometer: use a screw-
driver to adjust the “gain”
potentiometer clockwise to
the unstable speed, then
counterclockwise until to the
stable speed, and then back
to adjust a small grid. Note :
the potentiometer can only
a)Governor problem rotate by 300 degrees. Do not
D：Unstable speed of gov- use too much force to dam-
ernor age the potentiometer, which
may also cause unstable
speed.
If speed is still unstable, set
the “gain”potentiometer to
10 o 'clock and then adjust
the “stability” potentiometer
as in last step.
If it is not stable, adjust Red
State Switch now, adjust
RSW-1 to up position, and
repeat last two steps.
Recheck and clean and rein-
stall speed sensor. Note that
b) Speed sensor or installa-
speed sensor can only be
tion problem.
connected to controller.

106
 Appendix

6.4.2 Diagnostic Fault Codes List for 4M06

Description Code SPN FMI P- code

12 P2519
Fault path of air condition power stage 3-1-3 985
2 P2519

3 P060B

4 P060B
Error status of ADC monitoring 1-1-1 520192
11 P060B

2 P060B

3 P0123

Fault path of Accelerator Pedal 1 2-2-1 91 4 P0122

2 P2135

3 P0223

Fault path of Accelerator Pedal 2 2-2-1 29 4 P0222

2 P2135

3 P2229

4 P2228
Error path of atmospheric pressure sensor 2-3-2 108
12 P0000

2 P2227

3 P0649

4 P0649
Error path for the Adjustable Speed Limit lamp 3-3-6 520194
5 P0649

2 P0649

Error path for AccPed and Brake Plausibility 2-2-5 91 7 P2299

AirCtl permanent positive governor deviation 4-5-3 520195 15 P0402

AirCtl permanent negative governor deviation 4-5-3 520196 17 P0401

Grid heaters always switched on 3-2-2 676 7 P0540

3 P1020
Fault path1 of air heater test switch on 3-2-3 729
4 P1021

3 P1022
Fault path2 of air heater test switch off 3-2-3 730
4 P1023

3 P0542
Error path of power stage air heater 1 actuator 3-2-1 729
4 P0541

107
Appendix

Description Code SPN FMI P- code

Fault path for short circuit to battery for BPA power
3-4-4 1192 3 P0048
stage
Fault path for short circuit to ground for BPA power
3-4-4 1192 4 P0047
stage

Fault path for no load and excess temperature for 12 P0045

3-4-4 1192
BPA power stage 2 P0046

3 P0238

4 P0237
Error path for boost pressure sensor 2-3-1 102
12 P0235

2 P0236

3 P0563
Battery voltage fault 1-2-4 168
4 P0562

12 P0571
Error path for brake signal 2-2-3 597
2 P0504

3 P022C

Error path of Intercooler Bypass Valve Power stage 2-2-4 520197 4 P022B

12 P022A

3 P2559

4 P2558
Error path for coolant level sensor 2-4-6 111
12 P2556

2 P2557

3 P0080

4 P0079
Fault path of CRERCD condition power stage 3-2-5 1072
255 P1633

255 P1634

3 P1635

4 P1636
Error path for the cold start lamp 3-3-5 1081
12 P1637
2 P1638
3 P0118

4 P0117
Error path of coolant temperature sensor 2-4-1 110
12 P0115

2 P0116

108
 Appendix

Description Code SPN FMI P- code

Coolant temperature sensor absolute test 2-4-5 520198 2 P0116

Coolant temperature sensor dynamic test 2-4-5 520198 2 P0116

Error path for Misfire cylinder 1 5-1-1 1323 3 P0301

Error path for Misfire cylinder 2 5-1-2 1324 3 P0302

Error path for Misfire cylinder 3 5-1-3 1325 3 P0303

Error path for Misfire cylinder 4 5-3-1 1326 3 P0304

Error path for Misfire cylinder 5 5-3-2 1327 3 P0305

Error path for Misfire cylinder 6 5-3-3 1328 3 P0306

Error path for misfire in multiple cylinders 5-1-4 1322 3 P0300

Physical plausibility DCS 2-2-8 520199 2 P0856

Fault path for compression test 5-2-1 520200 20 P161F

Diagnostic fault path signals errors of main clutch 12 P0704

2-2-2 598
signal 2 P0704

3 P0073

Error path of environment air temperature sensor 2-3-5 171 4 P0072

12 P0071

3 P1505
Error path of BET temperature sensor 2-3-5 520201
4 P1506

3 P1507
Error path of ClgZn temperature sensor 2-3-5 520202
4 P1508

3 P1509
Error path of Inside air temperature sensor 2-3-5 520203
4 P150A
Fault path for Engine Brake Pre-Selection switch
3-4-2 520204 2 P1635
status
3 P245D
Error path of power stage for EGR Bypass valve
3-5-1 520205 4 P245C
actuator
12 P245A

Fault path 1 for Engine Compartment Start Button 3-4-3 1041 8 P2530

3 P0473

Error path for Exhaust Gas Pipe Pressure Sensor 3-4-5 520206 4 P0472

2 P0470

109
Appendix

Description Code SPN FMI P- code

Fault path for short circuit to battery for EGR power
3-5-1 2791 3 P0490
stage
Fault path for short circuit to ground for EGR power
3-5-1 2791 4 P0489
stage

Fault path for no load and excess temperature for 5 P0404

3-5-1 2791
EGR power stage 2 P0403
If running with camshaft only is active the fault path is
1-1-4 190 12 P0008
set
12 P0340
Error path of camshaft failure 1-1-3 636
11 P0341

12 P0335
Error path of crankshaft failure 1-1-2 190
11 P0336

Error path of offset between camshaft and crank-shaft 5-4-1 190 7 P0016

Fault path of engine Protection 2-2-6 533 15 P0219

Error path for Short circuit to Batt of power stage for
3-1-1 1074 3 P0478
Exhaust Flap actuator
Error path Short circuit to Ground of power stage for
3-1-1 1074 4 P0477
Exhaust Flap actuator

Error path for Open circuit and excess temperature of 12 P0476

3-1-1 1074
Exhaust Flap actuator 2 P0476
Fault FMTC_trq2qBas_MAP contains non-strictly
1-2-5 520236 13 P1007
monotonous q curves
3 P0183
Fault Path for Fuel Temperature sensor 2-1-5 174
4 P0182

3 P0692

4 P0691
Error path of power stage fan actuator 3-1-2 1071
12 P0480

2 P0483

3 P0694
Error path of power stage fan 2 actuator 3-1-2 1071
4 P0693

3 P0526
Error path of fan speed sensor signal 3-1-2 1639
4 P0527

Fuel filter fouling switch 2-1-3 95 3 P1015

Fuel filter fouling switch 2-1-3 95 4 P1016

110
 Appendix

Description Code SPN FMI P- code

Fuel filter fouling switch 2-1-3 95 2 P1017

3 P1008
Fault path for fuel filter heating output 2-1-6 520207
4 P1009
Water in fuel sensor 2-1-4 97 3 P2267
Water in fuel sensor 2-1-4 97 4 P2266
Fuel filter fouling detection 2-1-2 95 7 P1018
Dfp for Water Detection Sensor 2-1-1 97 11 P2269
3 P0406

4 P0405
Dfp for Heater used in EGR Mass Flow rate 4-3-3 520208
12 P0409

2 P0409

3 P040D

Dfp for Recirculated Engine Exhaust Gas Temper- 4 P040C

4-3-2 520209
ature sensor 12 P040A

2 P040B

Dfp for message Dash Dspl 4-3-4 520210 3 U0158

Faults of CAN message EBC1 4-4-1 520211 12 P0000

Dfp for message ERC1DR 4-4-2 520212 3 U1100

Faults of CAN message ETC1 4-4-3 520213 12 U0103

Dfp for CAN message EngGsFlowRt 4-1-5 520214 12 U0113

Dfp timeout for message HRVD 4-1-6 520215 3 U1101

Df p for message RxAMCON 4-4-4 520216 3 U0156

Dfp for Time-out error of RxCCVS message 4-4-5 523218 12 U0104

Dfp for CAN message RxEngTemp2 4-5-1 523604 12 U1102

Faults of CAN message TCO1 4-4-6 523222 12 U0157
Dfp for message TF 4-5-2 520217 3 U1103
11 U1104
Dfp for messages TSC1-AE 4-2-1 523605
12 U1105

11 U1106
Dfp for message TSC1-AR 4-2-1 523606
12 U1107

11 U1108
Dfp for messages TSC1-DE 4-2-2 523607
12 U1109

111
Appendix

Description Code SPN FMI P- code

11 U110A
Dfp for message TSC1-DR 4-2-2 523608
12 U110B
3 U110C
Dfp for message TSC1-PE 4-2-3 520218
4 U110D

11 U110E
Dfp for messages TSC1-TE 4-2-4 898
12 U110F

11 U113A
Dfp for message TSC1-TR 4-2-4 520
12 U113B

3 U1110
Dfp for messages TSC1-VE 4-2-5 520219
12 U1111

3 U1112
Dfp for message TSC1-VR 4-2-5 520220
12 U1113
Dfp timeout for message Time Date 4-1-7 520237 3 U1114
Faults of CAN message WSI 4-3-5 520238 12 U1115
Faults in CAN send messages 4-3-1 523500 12 U0001
Physical plausibility TSC 2-2-7 520221 2 U0404
3 P1623

4 P1624
Power Stage fault status for Generic Lamp 1 3-3-4 624
12 P1625

2 P1626

3 P1627

4 P1628
Power Stage fault status for Generic Lamp 2 3-3-4 624
12 P1629

2 P162A

3 P162B

4 P162C
Power Stage fault status for Generic Lamp 3 3-3-4 624
12 P162D

2 P162E
Error state communication - SPI 2-6-3 523617 11 P060A
255 P0000

4 P062F
Error state of EEPROM 2-6-5 630
12 P062F

2 P062F

112
 Appendix

Description Code SPN FMI P- code

Error path for Recovery which is locked 520222 14 P0607
Error path for Recovery which is suppressed 2-6-1 520222 14 P0607

Error path for Recovery which is visible 520222 14 P0607

Error state supply voltage CJ940 upper limit 2-6-3 523612 3 P1607

Error state supply voltage CJ940 lower limit 2-6-3 523612 4 P1608

3 P150B
Error path of air humidity sensor 2-3-6 520224
4 P150C

3 P0098

Error path of air temperature sensor 2-3-3 105 4 P0097

12 P0099

16 P1300

Fault path of injection limitation 1-5-5 520225 15 P1301

11 P1302

3 P1203

4 P1204
Fault path bank1-specific errors -> stop engine 1-5-1 523350
11 P1205

11 P1206

11 P1207

11 P1208
Fault path bank1-specific warnings -> stop engine 1-5-1 523351
12 P1209

11 P120A

3 P120B

4 P120C
Fault path bank2-specific errors -> stop engine 1-5-2 523352
11 P120D

11 P120E

11 P120F

11 P1210
Fault path bank2-specific warnings -> stop engine 1-5-2 523353
12 P1211

11 P1212

113
Appendix

Description Code SPN FMI P- code

3 P062B

4 P062B
Fault path Chip-specific errors -> stop engine 1-5-3 523354
12 P062B

2 P062B

3 P062B

4 P062B
Fault path Chip-specific errors -> stop engine 1-5-3 523355
12 P062B

2 P062B

3 P0262
11 P0263
Fault path cylinder1-specific errors -> stop engine 1-4-1 651
8 P0261

11 P0263

11 P1213

11 P1214
Fault path cylinder1-specific warnings 1-4-1 651
12 P0201

11 P1215

3 P0265

11 P0266
Fault path cylinder2-specific errors -> stop engine 1-4-2 652
8 P0264

11 P0266

11 P1216

11 P1217
Fault path cylinder2-specific warnings 1-4-2 652
12 P0202

11 P1218

3 P0268
11 P0269
Fault path cylinder3-specific errors -> stop engine 1-4-3 653
8 P0267

11 P0269

11 P1219

11 P121A
Fault path cylinder3-specific warnings 1-4-3 653
12 P0203

11 P121B

114
 Appendix

Description Code SPN FMI P- code

3 P0271

11 P0272
Fault path cylinder4-specific errors -> stop engine 1-4-4 654
8 P0270

11 P0272

11 P121C

11 P121D
Fault path cylinder4-specific warnings 1-4-4 654
12 P0204

11 P121E

3 P0274

11 P0275
Fault path cylinder5-specific errors -> stop engine 1-4-5 655
8 P0273

11 P0275

11 P121F

11 P1220
Fault path cylinder5-specific warnings 1-4-5 655
12 P0205

11 P1221

3 P0277

11 P0278
Fault path cylinder6-specific errors -> stop engine 1-4-6 656
8 P0276
11 P0278
11 P1222

11 P1223
Fault path cylinder6-specific warnings 1-4-6 656
12 P0206

11 P1224
Fault path - The minimal number of injections was
1-5-4 520226 12 P1225
not reached -> stop engine
Fault path for cruise control actuating device evalu-
3-4-1 596 2 P0564
ation error
3 P0650
4 P0650
Power Stage fault status for MIL 3-3-3 1213
12 P0650
2 P0650
3 P0687
Error path for main relay 2 1-3-2 1485
4 P0686

115
Appendix

Description Code SPN FMI P- code

3 P154A

Error path of multiple state switch 3-2-7 520227 4 P154B

2 P154C

Error path for main relay 1 1-3-2 2634 3 P160E

Error path for main relay 1 1-3-2 2634 4 P160F

The fault path contains the supervision of the
communication between Watchdog of CY310 and
the controller. The path is used to handle the re- 2-6-4 523420 2 P060C
versible Shut-down of the system using the engine
coordinator
Bus off in CAN A 4-1-1 639 12 U0029

Bus off in CAN B 4-1-2 1231 12 U0038

Bus off in CAN C 4-1-3 1235 12 U0047

3 P250D

4 P250C
Error path for engine oil level sensor 2-4-7 98
12 P250A

2 P250B

3 P0523

4 P0522
Error path of oil pressure sensor 2-4-3 100
12 P0520

2 P0521

Error path for oil pressure too low error 2-4-3 100 17 P0524

3 P0198

4 P0197
Error path of oil temperature sensor 2-4-4 175
12 P0195

2 P100D
Error path of oil temperature sensor for above
2-4-4 175 17 P0196
norm-al error
Fault path of overrun monitoring 2-6-2 1108 16 P1613
Fault path for redundant engine speed calculation in
2-6-2 520228 15 P1614
overrun monitoring
Permanent governor deviation in PCR 4-5-4 520229 15 P2263

Permanent governor deviation in PCR 4-5-4 520230 17 P2263

116
 Appendix

Description Code SPN FMI P- code

3 P0629

4 P0628
Error path of power stage pre-supply pump 3-2-6 520231
12 P0627

2 P062A

Fault path for run up test 5-2-3 520232 255 P1615

12 P1616
Fault path for test of redundant shut off paths during
1-1-6 970 3 P1617
initialization
4 P1618
3 P0643
Sensor supply voltage 1 1-3-1 1079
4 P0642
3 P0653
Sensor supply voltage 2 1-3-1 1080
4 P0652
3 P0699
Sensor supply voltage 3 1-3-1 523601
4 P0698
Fault path for shut off test 5-3-4 520233 20 P1621
3 P1619

4 P161A
Power Stage fault status for System lamp 3-3-1 624
12 P161B

2 P161C
Error path for terminal 15 - contains plausibility error
1-2-3 158 12 P2533
[Sig] of T15
Fault path for Terminal 50 component driver -
1-2-2 1041 7 P2530
T50CD
0 P0501
11 P1510
Fault path 1 for vehicle speed sensing 3-2-4 84
12 P0500

2 P0501

3 P2158

4 P2160
Fault path 2 for vehicle speed sensing 3-2-4 1624
12 P2157

2 P2159

3 P1511

Fault path 3 for vehicle speed sensing 3-2-4 645 4 P1512

12 P1513

117
Appendix

Description Code SPN FMI P- code

Error path for dataset variant coding, Npl = Re- 11 P161D
quested variant could not be set, Sig = variant da- 5-2-4 520239
taset defect 2 P161E

3 P162F

4 P1630
Power Stage fault status for Warning Lamp 3-3-2 624
12 P1631

2 P1632

3 P0647

4 P0646
Fault path of air condition power stage 3-1-3 1351
12 P0645

2 P0645
HpTst 5-2-2 520223 20 P160C
5 P0251
Error path of metering unit PWM-power stage 1-3-5 523615
2 P0252

Error path of metering unit PWM-power stage 1-3-5 523615 3 P0254

Error path of metering unit PWM-power stage 1-3-5 523615 4 P0253

16 P025D
Error path of metering unit AD-channel 1-3-5 523615
18 P025C

0 P100E

Error path of rail pressure relief valve 1-3-4 523470 11 P100F

7 P1010

3 P0193
Error path of rail pressure 1-3-3 157
4 P0192

15 P0191
Error path RPS offset monitoring 1-3-3 157
17 P0191

Faults for checks in MeUn controlled mode 2-5-1 523613 16 P1011

Faults for checks in MeUn controlled mode 2-5-2 523613 15 P1012

Faults for checks in MeUn controlled mode 2-5-4 523613 17 P1013

Faults for checks in MeUn controlled mode 2-5-3 523613 4 P0087

Faults for checks in MeUn controlled mode 2-5-3 523613 3 P0088

Faults for checks in MeUn controlled mode 2-5-7 523613 18 P101A

Faults for checks in MeUn controlled mode 2-5-5 523613 2 P1014

118
 Appendix

Description Code SPN FMI P- code

Faults for checks in MeUn controlled mode 2-5-6 523613 7 P1018

Faults for checks in MeUn controlled mode 2-5-4 523613 5 P1019

3 P1636
12V sensor supply voltage 1-3-1 520235
4 P1637

Fault path for short circuit to battery or ground for 3 P0617

1-2-1 677
high power stage 4 P0616

3 P1638
Fault path for short circuit to battery or ground, no
load, or excess temperature for low side power 1-2-1 677 4 P1639
stage
5 P163A

119
Appendix

6.4.3 Diagnostic Fault Codes List for 4M06

Description Code SPN FMI

Message MS06 timeout error sent from Master ECU to Slave
5313 519848 6
ECU
Message MS07 timeout error sent from Master ECU to Slave
5313 519848 9
ECU
Message MS08 timeout error sent from Master ECU to Slave
5313 519848 11
ECU
Message MS11 timeout error sent from Master ECU to Slave
5313 519848 13
ECU
Message MS12 timeout error sent from Master ECU to Slave
5313 519848 16
ECU
Message MS06 timeout error sent from Master ECU to Slave
5313 519848 7
ECU(Slave ECU)
Message MS12 timeout error sent from Master ECU to Slave
5313 519848 17
ECU(Slave ECU)
Message MS06 byte error sent from Master ECU to Slave ECU 5313 519848 4
Message MS07 byte error sent from Master ECU to Slave ECU 5313 519848 8
Message MS08 byte error sent from Master ECU to Slave ECU 5313 519848 10
Message MS11 byte error sent from Master ECU to Slave ECU 5313 519848 12
Message MS12 byte error sent from Master ECU to Slave ECU 5313 519848 14
Message MS06 byte error sent from Master ECU to Slave
5313 519848 5
ECU(Slave ECU)
Message MS12 byte error sent from Master ECU to Slave
5313 519848 15
ECU(Slave ECU)
12V sensor supply voltage exceeds the upper limit 1335 519868 9
12V sensor supply voltage exceeds the upper limit(Slave ECU) 1335 519868 10
12V sensor supply voltage exceeds the lower limit 1335 519868 11
12V sensor supply voltage exceeds the lower limit(Slave ECU) 1335 519868 12
The 24-hour average load exceeds the threshold alarm 5342 519845 2
Message AMB timeout failure 5121 519803 2
Message AMB fault data length 5121 519802 14
Message timeout failure of AT1FC1 5121 519845 21
Message AT1FC1 fault data length 5121 519845 20
CAN receives frame EEC1B timeout error 5313 519679 2
CAN receives frame EEC2 timeout error 5313 519680 2
CAN receives frame EEC3 timeout error 5313 519681 2
CAN receives frame EFL timeout error 5313 519683 2
CAN receives frame EGRB timeout error 5313 5265 11
CAN receives frame EGRB data length error 5313 5265 2
CAN receives frame EngTemp timeout error 5313 519684 2

120
 Appendix

Description Code SPN FMI

CAN receives frame IC1 timeout error 5313 519689 2
CAN receives frame VD timeout error 5313 519696 2
Diagnostic fault check of detection of Bus off on CAN A 5312 519605 19
The DEC1 message rolling counter or checksum fails 5313 519617 8
DPMSAE fault 5121 3479 19
ECU temperature value exceeds the upper limit fault 1142 517114 5
ECU temperature value exceeds the upper limit fault(Slave ECU) 1142 519869 17
ECU temperature value exceeds the lower limit fault 1142 517114 6
ECU temperature value exceeds the lower limit fault(Slave ECU) 1142 519869 18
The key received by ECU cannot be verified by heartbeat 5121 519807 2
ECU receives the key receiving timeout 5121 519808 2
ECU temperature sensor untrusted failure 1142 517114 7
ECU temperature sensor untrusted failure(Slave ECU) 1142 519869 19
ECU temperature sensor correlation failure 1142 517114 0
ECU temperature sensor correlation failure 1142 517114 8
ECU temperature sensor correlation failure(Slave ECU) 1142 519869 14
ECU temperature sensor correlation failure(Slave ECU) 1142 519869 13
ECU temperature sensor chip memory failure 1142 517114 2
ECU temperature sensor chip memory failure(Slave ECU) 1142 519869 16
ECU temperature sensor component or wiring failure 1142 517114 1
ECU temperature sensor component or wiring failure(Slave
1142 519869 15
ECU)
ECU temperature physical value exceeds the upper limit 1142 1136 15
ECU temperature physical value exceeds the upper limit(Slave
1142 519869 11
ECU)
ECU temperature physical value exceeds the lower limit 1142 1136 17
ECU temperature physical value exceeds the lower limit(Slave
1142 519869 12
ECU)
CAN receives frame EEC5 timeout error 5313 519682 2
CAN receives frame EGF1 timeout error 5121 2659 2
EGF1 message data length failure 5121 2659 14
ETC1 message credibility check timer and check and untrusted
5313 519624 19
failures
ETC2 message credibility verifier and verifier and untrusted fail-
5313 519625 19
ures
The ETC7 message receives a fault that the drive shaft is not
5313 519692 19
allowed to start.
ETC7 message byte error 5121 519845 28
FD message timeout failure 5121 977 2
HRLFC message timeout failure 5121 519804 2
HRW message timeout failure 5121 519806 2

121
Appendix

Description Code SPN FMI

HRW message data length fault 5121 519805 14
LFC message timeout failure 5121 519809 2
MeUn setting value is abnormal in overrun state in MeUn mode 1331 517710 9
MeUn traffic is abnormal under low idle speed in MeUn mode 1331 517710 10
Zero flow negative rail pressure deviation abnormally in MeUn
1331 517710 4
mode
Abnormal leakage in MeUn mode 1331 517710 2
Abnormal positive rail pressure deviation in MeUn mode 1331 517710 1
Minimum rail pressure anomaly in MeUn mode 1331 517710 6
Abnormal maximum rail pressure value after PRV valve is
1333 517731 0
opened
PRV valve open 1233 517670 7
PRV valve opening times exceeded 1233 517670 15
PRV open time exceeded 1233 517670 1
Message RxDEC1 fault data length 5121 519847 18
T50 signal error 5131 519672 19
Message TCO1 fault data length 5121 519853 2
Message TRF1 timeout failure 5313 519645 2
Message TRF1 fault data length 5313 519645 14
Message TSC1ACCE passive timeout failure 5313 519635 10
Message TSC1ACCE timeout failure 5313 519718 2
Message TSC1ACCE fault data length 5313 519718 14
Message TSC1ACCE active timeout failure 5313 519635 2
Message TSC1ACCR passive timeout failure 5313 519691 10
Message TSC1ACCR timeout failure 5313 519719 2
Message TSC1ACCR fault data length 5313 519719 14
Message TSC1ACCR active timeout failure 5313 519691 2
Message TSC1AE passive timeout failure 5313 519636 10
Message TSC1AE timeout failure 5313 519646 2
Message TSC1AEfault data length 5313 519646 14
Message TSC1AE active timeout failure 5313 519636 2
Message TSC1AR passive timeout failure 5313 519637 10
Message TSC1AR timeout failure 5313 519694 2
Message TSC1AR fault data length 5313 519694 14
Message TSC1AR active timeout failure 5313 519637 2
Message TSC1DE passive timeout failure 5313 519638 10
Message TSC1DE timeout failure 5313 519647 2
Message TSC1DE fault data length 5313 519647 14
Message TSC1DE active timeout failure 5313 519638 2
Message TSC1DR passive timeout failure 5313 519639 10

122
 Appendix

Description Code SPN FMI

Message TSC1DR timeout failure 5313 519648 2
Message TSC1DR fault data length 5313 519648 14
Message TSC1DR active timeout failure 5313 519639 2
Message TSC1PE passive timeout failure 5313 519640 10
Message TSC1PE timeout failure 5313 519649 2
Message TSC1PE fault data length 5313 519649 14
Message TSC1PE active timeout failure 5313 519640 2
Message TSC1TE passive timeout failure 5313 519853 3
Message TSC1TE timeout failure 5313 519650 2
Message TSC1TE fault data length 5313 519650 14
Message TSC1TE active timeout failure 5313 519641 2
Message TSC1TR passive timeout failure 5313 519642 10
Message TSC1TR timeout failure 5121 519730 0
Message TSC1TR fault data length 5121 519747 0
Message TSC1TR active timeout failure 5313 519642 2
Message TSC1VE passive timeout failure 5313 519643 10
Message TSC1VE timeout failure 5313 519651 2
Message TSC1VE fault data length 5313 519651 14
Message TSC1VE active timeout failure 5313 519643 2
Message TSC1VR passive timeout failure 5313 519644 10
Message TSC1VR timeout failure 5313 519652 2
Message TSC1VR fault data length 5313 519652 14
Message TSC1VR active timeout failure 5313 519644 2
Message TxTC1 timeout failure 5121 519735 0
Message VDC1 timeout failure 5313 519653 2
Message VDC1 fault data length 5313 519653 14
Message VDHR timeout failure 5313 519654 2
Message VDHR fault data length 5313 519654 14
Message VEP1 timeout 5121 519853 4
Message VH timeout failure 5121 519736 0
Message AmbCon timeout failure 5313 519676 2
Message ComRx_ActvCode data length failure 5313 519606 14
Message ComRx_CCVS timeout failure 5313 519847 17
Message ComRx_CCVS creditability validation failure 5313 519678 19
Message ComRx_CCVS fault data length 5313 519847 16
Fault message ComRx_CM1 timeout 5313 519615 2
Message ComRx_CM1 fault data length 5313 519615 14
Fault message ComRx_ComEGSPMInit timeout 5313 519198 2
Fault message ComRx_DashDispl timeout 5313 519616 2
Message ComRx_DashDispl fault data length 5313 519616 14

123
Appendix

Description Code SPN FMI

Message ComRx_DEC1 timeout failure 5313 519629 2
Message ComRx_DEC1 timeout failure 5121 519847 19
Fault message ComRx_EBC1 timeout 5313 519621 2
Message ComRx_EBC1 fault data length 5313 519621 14
Fault message ComRx_EBC2 timeout 5313 519622 2
Message ComRx_EBC2 fault data length 5313 519622 14
Message ComRx_EGSPMData1 timeout failure 5313 519201 2
Message ComRx_EGSPMData1 fault data length 5313 519201 10
Fault message ComRx_EGSPMData2 timeout 5313 519197 2
Message ComRx_EGSPMData2 fault data length 5313 519197 10
Message ComRx_EGSPMInit fault data length 5313 519198 10
Fault message ComRx_EGSPMMode6Diag timeout 5313 519199 2
Message ComRx_EGSPMMode6Dia fault data length 5313 519199 10
Fault message ComRx_EGSPMSemiContDiag timeout 5313 519200 2
Message ComRx_EGSPMSemiContDiag fault data length 5313 519200 10
Fault message ComRx_ERC1 timeout 5313 519685 2
Fault message ComRx_ETC1 timeout 5313 519624 2
Message ComRx_ETC1 fault data length 5313 519624 14
Fault message ComRx_ETC2 timeout 5313 519625 2
Message ComRx_ETC2 fault data length 5313 519625 14
Fault message ComRx_ETC7 timeout 5313 519686 2
Fault message ComRx_FlEco timeout 5313 519687 2
Fault message ComRx_HRW timeout 5313 519626 2
Message ComRx_HRW fault data length 5313 519626 14
Message ComRx_TCO1 timeout failure 5313 519717 2
Message ComRx_TimeDate timeout failure 5313 519633 2
Message ComRx_TimeDate fault data length 5313 519633 14
Message ComRx_ActvCode timeout failure 5313 519606 2
Message ComTx_CCVS timeout failure 5313 519695 2
Message ComTx_EGSPM timeout failure 5313 519201 11
Message ComTx_MFD1 timeout failure 5313 519690 2
Message ComTx_ShutDwn timeout failure 5313 519634 2
Message WFI timeout failure 5313 519697 2
No idling failure reminders allowed. 1431 519800 0
No stop engine errors reminder allowed 1431 519801 0
Sensor 5V supply voltage 1 exceeds the upper limit 1335 519867 17
Sensor 5V supply voltage 1 exceeds the upper limit(Slave ECU) 1335 519867 18
Sensor 5V supply voltage 1 exceeds the lower limit 1335 519867 19
Sensor 5V supply voltage 1 exceeds the lower limit(Slave ECU) 1335 519867 20
Sensor 5V supply voltage 1 error 1335 519867 21

124
 Appendix

Description Code SPN FMI

Sensor 5V supply voltage 1 error(Slave ECU) 1335 519867 22
Sensor 5V supply voltage 2 exceeds the upper limit 1335 519867 23
Sensor 5V supply voltage 2 exceeds the upper limit(Slave ECU) 1335 519867 24
Sensor 5V supply voltage 2 exceeds the lower limit 1335 519867 25
Sensor 5V supply voltage 2 exceeds the lower limit(Slave ECU) 1335 519867 26
Sensor 5V supply voltage 2 failure 1335 519867 27
Sensor 5V supply voltage 2 failure(Slave ECU) 1335 519867 28
Sensor 5V supply voltage 3 exceeds the upper limit 1335 519867 29
Sensor 5V supply voltage 3 exceeds the upper limit(Slave ECU) 1335 519867 30
Sensor 5V supply voltage 3 exceeds the lower limit 1335 519867 31
Sensor 5V supply voltage 3 exceeds the lower limit(Slave ECU) 1335 519868 0
Sensor 5V supply voltage 3 error 1335 519868 1
Sensor 5V supply voltage 3 error(Slave ECU) 1335 519868 2
Sensor 5V supply voltage 4 exceeds the upper limit 1335 519868 3
Sensor 5V supply voltage 4 exceeds the upper limit(Slave ECU) 1335 519868 4
Sensor 5V supply voltage 4 exceeds the lower limit 1335 519868 5
Sensor 5V supply voltage 4 exceeds the lower limit(Slave ECU) 1335 519868 6
Sensor 5V supply voltage 4 error 1335 519868 7
Sensor 5V supply voltage 4 error(Slave ECU) 1335 519868 8
Sensor voltage and idle switch status are not trusted 5332 558 2
Sensor voltage and idle switch status are not trusted(Slave ECU) 5332 519868 19
Cylinder1 injector of Slave ECU short circuit(Slave ECU) 1222 1413 3
Cylinder1 injector of Slave ECU high side low side short cir-
1222 1413 4
cuit(Slave ECU)
Cylinder1 injector of Slave ECU open load(Slave ECU) 1222 1413 5
Cylinder2 injector of Slave ECU short circuit(Slave ECU) 1222 1414 3
Cylinder2 injector of Slave ECU high side low side short cir-
1222 1414 4
cuit(Slave ECU)
Cylinder2 injector of Slave ECU open load(Slave ECU) 1222 1414 5
Cylinder3 injector of Slave ECU short circuit(Slave ECU) 1222 1415 3
Cylinder3 injector of Slave ECU high side low side short cir-
1222 1415 4
cuit(Slave ECU)
Cylinder3 injector of Slave ECU open load(Slave ECU) 1222 1415 5
Cylinder4 injector of Slave ECU short circuit(Slave ECU) 1222 1416 3
Cylinder4 injector of Slave ECU high side low side short cir-
1222 1416 4
cuit(Slave ECU)

Cylinder4 injector of Slave ECU open load（Slave ECU） 1222 1416 5

Cylinder5 injector of Slave ECU short circuit(Slave ECU) 1222 1417 3

Cylinder5 injector of Slave ECU high side low side short cir-
1222 1417 4
cuit(Slave ECU)

125
Appendix

Description Code SPN FMI

Cylinder5 injector of Slave ECU open load(Slave ECU) 1222 1417 5
Cylinder6 injector of Slave ECU short circuit(Slave ECU) 1222 1418 3
Cylinder6 injector of Slave ECU high side low side short cir-
1222 1418 4
cuit(Slave ECU)

Cylinder6 injector of Slave ECU open load（Slave ECU） 1222 1418 5

Cylinder7 injector of Slave ECU short circuit(Slave ECU) 1222 1419 3

Cylinder7 injector of Slave ECU high side low side short cir-
1222 1419 4
cuit(Slave ECU)
Cylinder7 injector of Slave ECU open load(Slave ECU) 1222 1419 5
Cylinder8 injector of Slave ECU short circuit(Slave ECU) 1222 1420 3
Cylinder8 injector of Slave ECU high side low side short cir-
1222 1420 4
cuit(Slave ECU)

Cylinder8 injector of Slave ECU open load（Slave ECU） 1222 1420 5

Message MS10 timeout error sent from Slave ECU to Master

5341 519637 0
ECU
Message MS10 byte error sent from Slave ECU to Master ECU 5341 519636 0
Message MS05 timeout error sent from Slave ECU to Master
5314 519633 0
ECU
Message MS05 timeout error sent from Slave ECU to Master
5314 519848 3
ECU(Slave ECU)
Message MS05 byte error sent from Slave ECU to Master ECU 5314 519632 0
Message MS05 byte error sent from Slave ECU to Master
5314 519848 2
ECU(Slave ECU)
Message MS09 timeout error sent from Slave ECU to Master
5341 519635 0
ECU
Message MS09 byte error sent from Slave ECU to Master ECU 5341 519634 0
Message MS13 timeout error sent from Slave ECU to Master
5341 519848 19
ECU
Message MS13 byte error sent from Slave ECU to Master ECU 5341 519848 18
Message MS16 timeout error sent from Slave ECU to Master
5341 519848 29
ECU
Message MS16 byte error sent from Slave ECU to Master ECU 5341 519848 28
Message MS17 timeout error sent from Slave ECU to Master
5341 519848 31
ECU
Message MS17 byte error sent from Slave ECU to Master ECU 5341 519848 30
Message MS18 timeout error sent from Slave ECU to Master
5341 519849 1
ECU
Message MS18 byte error sent from Slave ECU to Master ECU 5341 519849 0

126
 Appendix

Description Code SPN FMI

Message MS19 timeout error sent from Slave ECU to Master
5341 519849 3
ECU
Message MS19 byte error sent from Slave ECU to Master ECU 5341 519849 2
Message MS20 timeout error sent from Slave ECU to Master
5341 519849 5
ECU
Message MS20 byte error sent from Slave ECU to Master ECU 5341 519849 4
Message MS21 timeout error sent from Slave ECU to Master
5341 519849 7
ECU
Message MS21 byte error sent from Slave ECU to Master ECU 5341 519849 6
Message MS22 timeout error sent from Slave ECU to Master
5341 519849 9
ECU
Message MS22 byte error sent from Slave ECU to Master ECU 5341 519849 8
Message MS23 timeout error sent from Slave ECU to Master
5341 519849 11
ECU
Message MS23 byte error sent from Slave ECU to Master ECU 5341 519849 10
Message MS24 timeout error sent from Slave ECU to Master
5341 519849 13
ECU
Message MS24 byte error sent from Slave ECU to Master ECU 5341 519849 12
Message MS25 timeout error sent from Slave ECU to Master
5341 519849 15
ECU
Message MS25 byte error sent from Slave ECU to Master ECU 5341 519849 14
Message MS26 timeout error sent from Slave ECU to Master
5341 519849 17
ECU
Message MS26 byte error sent from Slave ECU to Master ECU 5341 519849 16
Message MS27 timeout error sent from Slave ECU to Master
5341 519849 19
ECU
Message MS27 byte error sent from Slave ECU to Master ECU 5341 519849 18
Message MS28 timeout error sent from Slave ECU to Master
5341 519849 21
ECU
Message MS28 byte error sent from Slave ECU to Master ECU 5341 519849 20
Message MS29 timeout error sent from Slave ECU to Master
5341 519849 23
ECU
Message MS29 byte error sent from Slave ECU to Master ECU 5341 519849 22
Message MS30 timeout error sent from Slave ECU to Master
5341 519849 25
ECU
Message MS30 byte error sent from Slave ECU to Master ECU 5341 519849 24
Message MS31 timeout error sent from Slave ECU to Master
5341 519849 27
ECU
Message MS31 byte error sent from Slave ECU to Master ECU 5341 519849 26
Message MS32 timeout error sent from Slave ECU to Master
5341 519849 29
ECU

127
Appendix

Description Code SPN FMI

Message MS32 byte error sent from Slave ECU to Master ECU 5341 519849 28
Message MS33 timeout error sent from Slave ECU to Master
5341 519849 31
ECU
Message MS33 byte error sent from Slave ECU to Master ECU 5341 519849 30
Message MS34 timeout error sent from Slave ECU to Master
5341 519851 1
ECU
Message MS34 byte error sent from Slave ECU to Master ECU 5341 519850 0
Message MS35 timeout error sent from Slave ECU to Master
5341 519851 3
ECU
Message MS35 byte error sent from Slave ECU to Master ECU 5341 519851 2
Message MS36 timeout error sent from Slave ECU to Master
5341 519851 5
ECU
Message MS36 byte error sent from Slave ECU to Master ECU 5341 519851 4
Message MS37 timeout error sent from Slave ECU to Master
5341 519851 7
ECU
Message MS37 byte error sent from Slave ECU to Master ECU 5341 519851 6
Message MS38 timeout error sent from Slave ECU to Master
5341 519851 10
ECU
Message MS38 timeout error sent from Slave ECU to Master
5341 519851 11
ECU(Slave ECU)
Message MS38 byte error sent from Slave ECU to Master ECU 5341 519851 8
Message MS38 byte error sent from Slave ECU to Master
5341 519851 9
ECU(Slave ECU)
Message MS39 timeout error sent from Slave ECU to Master
5341 519851 14
ECU
Message MS39 timeout error sent from Slave ECU to Master
5341 519851 15
ECU(Slave ECU)
Message MS39 byte error sent from Slave ECU to Master ECU 5341 519851 12
Message MS39 byte error sent from Slave ECU to Master
5341 519851 13
ECU(Slave ECU)
Message MS40 timeout error sent from Slave ECU to Master
5341 519851 18
ECU
Message MS40 timeout error sent from Slave ECU to Master
5341 519851 19
ECU(Slave ECU)
Message MS40 byte error sent from Slave ECU to Master ECU 5341 519851 16
Message MS40 byte error sent from Slave ECU to Master
5341 519851 17
ECU(Slave ECU)
Message MS41 timeout error sent from Slave ECU to Master
5341 519851 22
ECU
Message MS41 timeout error sent from Slave ECU to Master
5341 519851 23
ECU(Slave ECU)

128
 Appendix

Description Code SPN FMI

Message MS41 byte error sent from Slave ECU to Master ECU 5341 519851 20
Message MS41 byte error sent from Slave ECU to Master
5341 519851 21
ECU(Slave ECU)
Message MS42 timeout error sent from Slave ECU to Master
5341 519851 26
ECU
Message MS42 timeout error sent from Slave ECU to Master
5341 519851 27
ECU(Slave ECU)
Message MS42 byte error sent from Slave ECU to Master ECU 5341 519851 24
Message MS42 byte error sent from Slave ECU to Master
5341 519851 25
ECU(Slave ECU)
Message MS43 timeout error sent from Slave ECU to Master
5341 519851 30
ECU
Message MS43 timeout error sent from Slave ECU to Master
5341 519851 31
ECU(Slave ECU)
Message MS43 byte error sent from Slave ECU to Master ECU 5341 519851 28
Message MS43 byte error sent from Slave ECU to Master
5341 519851 29
ECU(Slave ECU)
Message MS44 timeout error sent from Slave ECU to Master
5341 519852 2
ECU
Message MS44 timeout error sent from Slave ECU to Master
5341 519852 3
ECU(Slave ECU)
Message MS44 byte error sent from Slave ECU to Master ECU 5341 519852 0
Message MS44 byte error sent from Slave ECU to Master
5341 519852 1
ECU(Slave ECU)
Message MS45 timeout error sent from Slave ECU to Master
5341 519852 5
ECU
Message MS45 byte error sent from Slave ECU to Master ECU 5341 519852 4
Message MS46 timeout error sent from Slave ECU to Master
5341 519852 7
ECU
Message MS46 byte error sent from Slave ECU to Master ECU 5341 519852 6
Message MS47 timeout error sent from Slave ECU to Master
5341 519852 9
ECU
Message MS47 byte error sent from Slave ECU to Master ECU 5341 519852 8
Message MS48 timeout error sent from Slave ECU to Master
5341 519852 11
ECU
Message MS48 byte error sent from Slave ECU to Master ECU 5341 519852 10
Message MS49 timeout error sent from Slave ECU to Master
5341 519852 13
ECU
Message MS49 byte error sent from Slave ECU to Master ECU 5341 519852 12
Message MS50 timeout error sent from Slave ECU to Master
5341 519852 15
ECU

129
Appendix

Description Code SPN FMI

Message MS50 byte error sent from Slave ECU to Master ECU 5341 519852 14
Message MS51 timeout error sent from Slave ECU to Master
5341 519852 17
ECU
Message MS51 byte error sent from Slave ECU to Master ECU 5341 519852 16
Message MS52 timeout error sent from Slave ECU to Master
5341 519852 19
ECU
Message MS52 byte error sent from Slave ECU to Master ECU 5341 519852 18
Message MS53 timeout error sent from Slave ECU to Master
5341 519852 21
ECU
Message MS53 byte error sent from Slave ECU to Master ECU 5341 519852 20
Message MS54 timeout error sent from Slave ECU to Master
5341 519852 23
ECU
Message MS54 byte error sent from Slave ECU to Master ECU 5341 519852 22
Message MS55 timeout error sent from Slave ECU to Master
5341 519852 25
ECU
Message MS55 byte error sent from Slave ECU to Master ECU 5341 519852 24
Message MS56 timeout error sent from Slave ECU to Master
5341 519852 28
ECU
Message MS56 timeout error sent from Slave ECU to Master
5341 519852 29
ECU(Slave ECU)
Message MS56 byte error sent from Slave ECU to Master ECU 5341 519852 26
Message MS56 byte error sent from Slave ECU to Master
5341 519852 27
ECU(Slave ECU)
Message MS57 timeout error sent from Slave ECU to Master
5341 519852 31
ECU
Message MS57 byte error sent from Slave ECU to Master ECU 5341 519852 30
Message MS58 timeout error sent from Slave ECU to Master
5341 519853 1
ECU
Message MS58 byte error sent from Slave ECU to Master ECU 5341 519853 0
Error 0 in MSM01 message sent from Slave ECU to Master ECU 5341 519810 0
Error 1 in MSM02 message sent from Slave ECU to Master ECU 5341 519821 0
Error 10 in MSM03 message sent from Slave ECU to Master
5341 519811 0
ECU
Error 2 in MSM04 message sent from Slave ECU to Master ECU 5341 519832 0
Error 3 in MSM05 message sent from Slave ECU to Master ECU 5341 519835 0
Error 4 in MSM06 message sent from Slave ECU to Master ECU 5341 519836 0
Error 5 in MSM07 message sent from Slave ECU to Master ECU 5341 519837 0
Error 6 in MSM08 message sent from Slave ECU to Master ECU 5341 519838 0
Error 7 in MSM09 message sent from Slave ECU to Master ECU 5341 519839 0
Error 8 in MSM10 message sent from Slave ECU to Master ECU 5341 519840 0
Error 9 in MSM11 message sent from Slave ECU to Master ECU 5341 519841 0

130
 Appendix

Description Code SPN FMI

Slave ECU top dead center angle calculation failed 1341 519868 17
Slave ECU top dead center angle is abnormal 1341 519868 18
Battery Voltage exceeds upper limit 5411 168 3
Battery Voltage exceeds below limit 5411 168 4
Low Battery voltage indication 5411 167 1
High Battery Voltage indication 5411 167 0
Electric control oil pump drive pin short circuit to ground 1411 517800 4
Electric control oil pump drive pin short circuit to battery 1411 517800 3
Over temperature fault of Electronically controlled oil pump drive
1411 517800 6
pin
Electric control oil pump drive pin open circuit 1411 517800 5
Short circuit to ground error at Electronically controlled fuel pump 1234 6614 4
Short circuit to ground error at Electronically controlled fuel
1234 519865 22
pump(Slave ECU)
Short circuit to battery error at Electronically controlled fuel pump 1234 6614 3
Short circuit to battery error at Electronically controlled fuel
1234 519865 21
pump(Slave ECU)
Electronically controlled fuel pump over temperature 1234 6614 6
Electronically controlled fuel pump over temperature(Slave ECU) 1234 519865 20
Electronically controlled fuel pump open circuit 1234 6614 5
Electronically controlled fuel pump open circuit(Slave ECU) 1234 519865 19
Multi-function switch trigger timeout 5221 596 2
Generators produce low power 1211 1795 4
The generator generates high voltage 1211 1795 3
Power rate adjustment knob original voltage exceeds the upper
1334 519668 3
limit
Power generation speed adjustment knob original voltage ex-
1334 519668 4
ceeds the lower limit fault
Power rate adjustment knob original voltage exceeds the lower
1334 519720 4
limit
Engine over speed failure 1313 1769 11
Engine synchronization lost 1141 517910 1
Engine synchronization lost(Slave ECU) 1141 519855 7
Engine normal operation relay short circuit to ground 5433 519862 23
Engine normal operation relay short circuit to battery 5433 519862 22
Engine normal operation relay over temperature fault 5433 519862 21
Engine normal operation relay open circuit failure 5433 519862 20
Engine speed signal output shorted to ground 5343 1623 4
Engine speed signal output shorted to battery 5343 1623 3
Engine speed signal output over temperature 5343 1623 6
Engine speed signal output open circuit 5343 1623 5

131
Appendix

Description Code SPN FMI

Error sending message channel configuration 5121 519847 13
Repeated error activation limit level 1 failure 5333 519305 1
Short circuit to ground error at Fan PWM 5223 519719 4
Short circuit to battery error at Fan PWM 5223 519719 3
Fan PWM over temperature 5223 519719 6
Fan PWM open circuit 5223 519719 5
Short circuit to ground error at Fan relay 0 5223 4815 4
Short circuit to battery error at Fan relay 0 5223 4815 3
Fan relay 0 over temperature 5223 4815 6
Fan relay 0 open circuit 5223 4815 5
Short circuit to ground error at Fan relay 1 5223 519699 4
Short circuit to battery error at Fan relay 1 5223 519699 3
Fan relay 1 over temperature 5223 519699 6
Fan relay 1 open circuit 5223 519699 5
Fan speed exceeds the upper limit fault 5223 1639 3
Fan speed exceeds the lower limit fault 5223 1639 4
Fan speed sensor cycle signal out of range fault 5223 4815 8
Short circuit to gound error at Fault diagnosis lamp 5331 519669 4
Short circuit to battery error at Fault diagnosis lamp 5331 519669 3
Fault diagnosis lamp over temperature 5331 519669 6
Fault diagnosis lamp open circuit 5331 519669 5
Rail pressure sensor voltage exceeds the upper limit 1333 157 3
Rail pressure sensor voltage exceeds the lower limit 1333 3516 4
Low rail cut-off injection 1332 517785 14
Sea boat request to cancel the restriction 5424 519306 1
Post lubrication failure 1423 5521 12
ambient pressure sensor acquisition chain failure 5141 108 2
ambient pressure sensor acquisition chain failure(Slave ECU) 5141 519855 20
Ambient pressure sensor storage error 5141 108 11
Ambient pressure sensor storage error 5141 108 14
Ambient pressure sensor storage error(Slave ECU) 5141 519855 22
Ambient pressure sensor storage error(Slave ECU) 5141 519855 25
Ambient pressure sensor or line fault 5141 108 12
Ambient pressure sensor or line fault(Slave ECU) 5141 519855 21
Ambient pressure physical value exceeds the upper limit 5141 108 16
Ambient pressure physical value exceeds the upper limit(Slave
5141 519855 23
ECU)
Ambient pressure physical value exceeds the lower limit 5141 108 18
Ambient pressure physical value exceeds the lower limit(Slave
5141 519855 24
ECU)

132
 Appendix

Description Code SPN FMI

Short circuit to ground error at Oil filter maintenance lamp 5431 519863 4
Short circuit to battery error at Oil filter maintenance lamp 5431 519863 2
Oil filter maintenance lamp over temperature 5431 519863 0
Oil filter maintenance lamp open circuit 5431 519862 30
Oil temperature sensor voltage exceeds the upper limit 1134 175 3
Oil temperature sensor voltage exceeds the upper limit(Slave
1134 519863 27
ECU)
Oil temperature sensor voltage exceeds the lower limit 1134 175 4
Oil temperature sensor voltage exceeds the lower limit(Slave
1134 519863 28
ECU)
Oil temperature signal physical value exceeds the upper limit 1133 175 15
Oil temperature signal physical value exceeds the upper lim-
1133 519863 25
it(Slave ECU)
Oil temperature signal physical value exceeds the lower limit 1133 175 17
Oil temperature signal physical value exceeds the lower lim-
1133 519863 26
it(Slave ECU)
Oil pressure sensor voltage exceeds the upper limit 1133 100 3
Oil pressure sensor voltage exceeds the upper limit(Slave ECU) 1133 519863 23
Oil pressure sensor voltage exceeds the lower limit 1133 100 4
Oil pressure sensor voltage exceeds the lower limit(Slave ECU) 1133 519863 24
Oil pressure signal physical value exceeds the upper limit 1133 100 15
Oil pressure signal physical value exceeds the upper limit(Slave
1133 519863 21
ECU)
Oil pressure signal physical value exceeds the lower limit 1133 100 17
Oil pressure signal physical value exceeds the lower limit(Slave
1133 519863 22
ECU)
Diagnostic fault check to report the accelerator pedal position
1321 519666 11
error
Received drive idle signal circulation fault 5121 519842 1
Voltage too low times exceed limit when test air-inlet heating
5212 2898 18
function close
Over voltage times exceed limit when test air-inlet heating func-
5212 2898 16
tion close
Voltage too low times exceed limit when test air-inlet heating
5212 2898 17
function active
Over voltage times exceed limit when test air-inlet heating func-
5212 2898 15
tion active
Short circuit to ground error at Grid heater relay 5212 2898 4
Short circuit to ground error at Grid heater relay(Slave ECU) 5212 519859 30
Short circuit to battery error at Grid heater relay 5212 2898 3

133
Appendix

Description Code SPN FMI

Short circuit to battery error at Grid heater relay(Slave ECU) 5212 519859 29
Grid heater relay over temperature 5212 2898 6
Grid heater relay over temperature(Slave ECU) 5212 519859 28
open load for air intake relay 5212 2898 5

open load for air intake relay（Slave ECU） 5212 519859 27

Air inlet heating relay sticky 5212 2898 7

Intake manifold pressure sensor original voltage exceeds the
2132 102 0
upper limit fault
Intake manifold pressure sensor original voltage exceeds the
2132 519864 29
upper limit fault(Slave ECU)
Intake manifold pressure sensor original voltage exceeds the
2132 102 1
lower limit fault
Intake manifold pressure sensor original voltage exceeds the
2132 519864 30
lower limit fault(Slave ECU)
Intake manifold pressure physical value exceeds the upper limit
2132 102 16
fault
Intake manifold pressure physical value exceeds the upper limit
2132 519864 25
fault(Slave ECU)
Intake manifold pressure physical value exceeds the lower limit
2132 102 18
fault
Intake manifold pressure physical value exceeds the lower limit
2132 519864 26
fault(Slave ECU)
MS01Msg Credibility check Counter check 5313 519845 31
MS02Msg Credibility check Counter check 5313 519846 3
MS03Msg Credibility check Counter check 5313 519846 7
MS04Msg Credibility check Counter check 5313 519846 11
MS05Msg Credibility check Counter check 5313 519846 15
MS06Msg Credibility check Counter check 5313 519846 19
MS07Msg Credibility checksum error(Slave ECU) 5313 519846 22
MS08Msg Credibility check Counter check(Slave ECU) 5313 519846 24
MS09Msg Credibility check Counter check 5313 519846 26
MS10Msg Credibility check Counter check 5313 519846 28
MS11Msg Credibility check Counter check 5313 519846 30
MS12Msg Credibility check Counter check 5313 519847 1
MS13Msg Credibility check Counter check 5313 519847 4
MS14Msg Credibility check Counter check 5313 519847 7
MS15Msg Credibility check Counter check 5313 519847 11
TSC1ACCE Credibility check Counter check 5121 519722 0
ComTSC1ACCR Credibility check Counter check 5121 519724 0

134
 Appendix

Description Code SPN FMI

ComTSC1AECredibility check Counter check 5121 519726 0
DFC_ComTSC1AR Credibility check Counter check 5121 519728 0
ComTSC1DE Credibility check Counter check 5121 519740 0
ComTSC1DR Credibility check Counter check 5121 519742 0
ComTSC1PE Credibility check Counter check 5121 519744 0
ComTSC1TE Credibility check Counter check 5121 519746 0
ComTSC1TR Credibility check Counter check 5121 519749 0
ComTSC1VE Credibility check Counter check 5121 519732 0
Credibility check Counter check 5121 519734 0
MS01Msg Credibility check Counter check(Slave ECU) 5313 519846 0
MS02Msg Credibility check Counter check(Slave ECU) 5313 519846 4
MS03Msg Credibility check Counter check(Slave ECU) 5313 519846 8
MS04Msg Credibility check Counter check(Slave ECU) 5313 519846 12
MS05Msg Credibility check Counter check(Slave ECU) 5313 519846 16
MS06Msg Credibility check Counter check(Slave ECU) 5313 519846 20
MS12Msg Credibility check Counter check(Slave ECU) 5313 519847 2
MS14Msg Credibility check Counter check(Slave ECU) 5313 519847 8
MS15Msg Credibility check Counter check(Slave ECU) 5313 519847 12
MS01Msg Credibility checksum error 5313 519845 29
MS02Msg Credibility checksum error 5313 519846 1
MS03Msg Credibility checksum error 5313 519846 5
MS04Msg Credibility checksum error 5313 519846 9
MS05Msg Credibility checksum error 5313 519846 13
MS06Msg Credibility checksum error 5313 519846 17
MS07Msg Credibility checksum error 5313 519846 21
MS08Msg Credibility check Counter check 5313 519846 23
MS09Msg Credibility checksum error 5313 519846 25
MS10Msg Credibility checksum error 5313 519846 27
MS11Msg Credibility checksum error 5313 519846 29
MS12Msg Credibility checksum error 5313 519846 31
MS13Msg Credibility checksum error 5313 519847 3
MS14Msg Credibility checksum error 5313 519847 5
MS15Msg Credibility checksum error 5313 519847 9
ComTSC1ACCE Credibility checksum error 5121 519721 0
ComTSC1ACCR Credibility checksum error 5121 519723 0
ComTSC1AE Credibility checksum error 5121 519725 0
DFC_ComTSC1AR Credibility checksum error 5121 519727 0
ComTSC1DE Credibility checksum error 5121 519729 0
ComTSC1DR Credibility checksum error 5121 519741 0
ComTSC1PE Credibility checksum error 5121 519743 0
ComTSC1TE Credibility checksum error 5121 519745 0

135
Appendix

Description Code SPN FMI

ComTSC1TR Credibility checksum error 5121 519748 0
ComTSC1VE Credibility checksum error 5121 519731 0
ComTSC1VR Credibility checksum error 5121 519733 0
MS01Msg Credibility checksum error(Slave ECU) 5313 519845 30
MS02Msg Credibility checksum error(Slave ECU) 5313 519846 2
MS03Msg Credibility checksum error(Slave ECU) 5313 519846 6
MS04Msg Credibility checksum error(Slave ECU) 5313 519846 10
MS05Msg Credibility checksum error(Slave ECU) 5313 519846 14
MS06Msg Credibility checksum error(Slave ECU) 5313 519846 18
MS12Msg Credibility checksum error(Slave ECU) 5313 519847 0
MS14Msg Credibility checksum error(Slave ECU) 5313 519847 6
MS15Msg Credibility checksum error(Slave ECU) 5313 519847 10
The second air filter clogging failure 5413 2809 13
Air filter clogging failure 5413 107 13
Multi-state switching signal from CAN message is not available 5511 519865 23
T50 ignition switch error from ComRx_DEC1 message 5313 519632 19
Remote pedal overrun from ComRx_DEC1 message 5313 519629 19
Engine shutdown request from EBC1 message 5313 519623 19
Untrusted detection of current gear from ETC2 message 5313 519688 19
The actual state of the fan from the message is incorrect 5121 977 11
Short circuit to ground on cold start lamp 5224 626 4
Short circuit to battery on cold start lamp 5224 626 3
Cold start lamp over temperature 5224 626 6
Open load error for cold start lamp 5224 626 5
Continuous overload operation time alarm 5342 519845 1
Continuous running time average load exceeds threshold alarm 5342 519845 3
The common power operation time exceeds the threshold alarm
5342 519845 5
every year
The engine running time exceeds the threshold alarm every year 5342 519845 6
Each year the full load operation time exceeds the threshold
5342 519845 4
alarm
Torque limit activation after restart 1314 519659 3
Torque limit mode activation 5111 519698 11
Injector bank0 to ground short circuit fault 1222 517650 3
Injector bank0 to ground short circuit fault(Slave ECU) 1222 519860 10
Injector bank1 to ground short circuit fault 1222 517651 3
Injector bank1 to ground short circuit fault(Slave ECU) 1222 519860 11
Injector bank2 to ground short circuit fault 1222 517652 3
Injector bank2 to ground short circuit fault(Slave ECU) 1222 519860 12
Injector bank3 to ground short circuit fault 1222 517653 3
Injector bank3 to ground short circuit fault(Slave ECU) 1222 519860 13

136
 Appendix

Description Code SPN FMI

Frequency exceeds the upper limit 5243 517750 15
Frequency exceeds the lower limit 5243 517750 17
Average rail pressure exceeds upper and lower limits 1233 517670 0
Short circuit to ground error at Start relay low side 5245 7749 4
Short circuit to battery error at Start relay low side 5245 7749 3
Start relay low side over temperature 5245 7749 6
Start relay low side open circuit 5245 7749 5
The crankshaft has the wrong number of teeth, associated
1141 519754 0
Crankshaft signal loss
The crankshaft has the wrong number of teeth, associated
1141 519853 13
Crankshaft signal loss(Slave ECU)
Loss of crankshaft synchronization, associated Crankshaft signal
1141 519761 0
loss
Loss of crankshaft synchronization, associated Crankshaft signal
1141 519853 18
loss(Slave ECU)
The camshaft signal of crankshaft does not match, camshaft
1141 4201 1
signal error
The camshaft signal of crankshaft does not match, camshaft
1141 519845 7
signal error(Slave ECU)
Crankshaft without Gap, associated Crankshaft signal loss 1141 519751 0
Crankshaft without Gap, associated Crankshaft signal loss(Slave
1141 519853 8
ECU)
The Crankshaft signal is short-circuited to the ground and the
1141 519759 0
associated Crankshaft signal is lost
The Crankshaft signal is short-circuited to the ground and the
1141 519853 16
associated Crankshaft signal is lost(Slave ECU)
Crankshaft signal to virtual connection to battery, associated
1141 519753 0
Crankshaft signal loss
Crankshaft signal to virtual connection to battery, associated
1141 519853 12
Crankshaft signal loss(Slave ECU)
Crankshaft signal short circuit to power supply, associated
1141 519758 0
Crankshaft signal loss
Crankshaft signal short circuit to power supply, associated
1141 519853 15
Crankshaft signal loss(Slave ECU)
Crankshaft signal to virtual connection to power supply, associ-
1141 519752 0
ated Crankshaft signal loss
Crankshaft signal to virtual connection to power supply, associ-
1141 519853 11
ated Crankshaft signal loss(Slave ECU)
Sometimes there is no Crankshaft signal, associated Crankshaft
1141 519757 0
signal loss

137
Appendix

Description Code SPN FMI

Sometimes there is no Crankshaft signal, associated Crankshaft
1141 519853 14
signal loss(Slave ECU)
Crankshaft signal has glitch interference, associated Crankshaft
1141 519760 0
signal loss
Crankshaft signal has glitch interference, associated Crankshaft
1141 519853 17
signal loss(Slave ECU)
Short circuit to ground error at Fuel filter maintenance lamp 5432 519857 4
Short circuit to ground error at Fuel filter maintenance
5432 519857 5
lamp(Slave ECU)
Short circuit to battery error at Fuel filter maintenance lamp 5432 519857 2
Short circuit to battery error at Fuel filter maintenance
5432 519857 3
lamp(Slave ECU)
Fuel filter maintenance lamp over temperature 5432 519857 0
Fuel filter maintenance lamp over temperature(Slave ECU) 5432 519857 1
Fuel filter maintenance lamp open circuit 5432 519856 30
Fuel filter maintenance lamp open circuit(Slave ECU) 5432 519856 31
Fuel filter blockage failure 1412 95 7
Fuel filter blockage failure(Slave ECU) 1412 519857 8
Fuel leak failure 1412 519857 6
Fuel leak failure(Slave ECU) 1412 519857 7
Battery voltage of device driver library exceeds upper limit 5411 444 15
Battery voltage of device driver library exceeds lower limit 5411 444 17
The voltage value of water temperature exceeds the upper limit 1111 110 0
The voltage value of water temperature exceeds the upper lim-
1111 519844 23
it(Slave ECU)
The voltage value of water temperature is too low 1111 110 17
The voltage value of water temperature is too low(Slave ECU) 1111 519844 24
The original voltage of water temperature signal exceeds the
1111 110 3
upper limit
The original voltage of water temperature signal exceeds the
1111 519844 25
upper limit(Slave ECU)
The initial voltage value of water temperature signal is too low 1111 110 4
The initial voltage value of water temperature signal is too
1111 519844 26
low(Slave ECU)
Accelerator pedal signal timeout fault 5313 91 2
Accelerator pedal signal exceeds limit fault 5313 91 19
Pedal frequency signal exceeds upper limit pre-alarm 5243 517750 16
Pedal frequency signal exceeds lower limit pre-alarm 5243 517750 18
Error in camshaft disk type, error in associated camshaft signal 1113 4201 5
Error in camshaft disk type, error in associated camshaft sig-
1113 519845 9
nal(Slave ECU)

138
 Appendix

Description Code SPN FMI

The camshaft signal is short-circuited to the ground and the as-
1113 4201 4
sociated camshaft signal is lost
The camshaft signal is short-circuited to the ground and the as-
1113 519845 12
sociated camshaft signal is lost(Slave ECU)
Camshaft signal short circuit to power supply, associated cam-
1113 4201 3
shaft signal loss
Camshaft signal short circuit to power supply, associated cam-
1113 519845 11
shaft signal loss(Slave ECU)
The camshaft signal has burr interference. 1113 4201 7
The camshaft signal has burr interference.(Slave ECU) 1113 519845 13
The number of demand injections is limited by the injector's
1214 517600 1
electrical demand to reach the maximum number of injections.
Hardware switch request to cancel the limit 5424 519306 0
Short circuit to ground error at fuel metering unit low side 1223 1442 8
Short circuit to battery error at fuel metering unit low side 1223 1442 4
Short circuit to ground error at fuel metering unit high side 1223 1442 6
Short circuit to battery error at fuel metering unit high side 1223 1442 3
Fuel metering unit high side and low side short circuit fault 1223 1442 9
Fuel metering unit open circuit failure 1223 1442 5
Accelerator pedal 1 voltage exceeds the lower limit 5243 91 4
The accelerator pedal 1 signal is not synchronized with the pedal
5332 519666 2
2 signal
Accelerator pedal 2 voltage exceeds the lower limit 5243 29 4
water in fuel 1122 519662 11
The original voltage of water in fuel sensor exceeds the upper
1115 519662 3
limit fault
The original voltage of water in fuel sensor exceeds the lower
1115 519662 4
limit fault
Short circuit to ground error at Water in fuel lamp 1115 519661 4
Short circuit to battery error at Water in fuel lamp 1115 519661 3
Water in fuel lamp over temperature 1115 519661 6
Water in fuel lamp open circuit 1115 519661 5
Oil leakage during pre-lubrication 1423 4210 0
Checking the master-slave ECU identity credibility currently or
1432 519868 16
verification is not passed
Intake pressure sensor raw voltage after intermediate cooling
2141 8488 3
exceeds the upper limit
Intake pressure sensor raw voltage after intermediate cooling
2141 519868 30
exceeds the upper limit(Slave ECU)
Intake pressure sensor raw voltage after intermediate cooling
2141 8488 17
exceeds the lower limit

139
Appendix

Description Code SPN FMI

Intake pressure sensor raw voltage after intermediate cooling
2141 519868 31
exceeds the lower limit(Slave ECU)
The physical value of the intake pressure after intermediate
2141 8488 0
cooling, exceeds the upper limit
The physical value of the intake pressure after intermediate
2141 519868 28
cooling, exceeds the upper limit(Slave ECU)
The physical value of the intake pressure after intermediate
2141 8488 4
cooling, exceeds the lower limit
The physical value of the intake pressure after intermediate
2141 519868 29
cooling, exceeds the lower limit(Slave ECU)
Cylinder1 injector of Master ECU short circuit 1222 1413 3
Cylinder1 injector of Master ECU high side low side short circuit 1222 1421 4
Cylinder1 injector of Master ECU open load 1222 1413 5
Cylinder2 injector of Master ECU short circuit 1222 1422 3
Cylinder2 injector of Master ECU high side low side short circuit 1222 1422 4
Cylinder2 injector of Master ECU open load 1222 1414 5
Cylinder3 injector of Master ECU short circuit 1222 1423 3
Cylinder3 injector of Master ECU high side low side short circuit 1222 1423 4
Cylinder3 injector of Master ECU open load 1222 1415 5
Cylinder4 injector of Master ECU short circuit 1222 1424 3
Cylinder4 injector of Master ECU high side low side short circuit 1222 1424 4
Cylinder4 injector of Master ECU open load 1222 1416 5
Cylinder5 injector of Master ECU short circuit 1222 1425 3
Cylinder5 injector of Master ECU high side low side short circuit 1222 1425 4
Cylinder5 injector of Master ECU open load 1222 1417 5
Cylinder6 injector of Master ECU short circuit 1222 1426 3
Cylinder6 injector of Master ECU high side low side short circuit 1222 1426 4
Cylinder6 injector of Master ECU open load 1222 1418 5
Cylinder7 injector of Master ECU short circuit 1222 1427 3
Cylinder7 injector of Master ECU high side low side short circuit 1222 1427 4
Cylinder7 injector of Master ECU open load 1222 1419 5
Cylinder8 injector of Master ECU short circuit 1222 1428 3
Cylinder8 injector of Master ECU high side low side short circuit 1222 1428 4
Cylinder8 injector of Master ECU open load 1222 1420 5
Message MS01 timeout error sent from Master ECU to Slave
5313 519847 22
ECU
Message MS01 timeout error sent from Master ECU to Slave
5313 519847 23
ECU(Slave ECU)
Message MS01 byte error sent from Master ECU to Slave ECU 5313 519847 20
Message MS01 byte error sent from Master ECU to Slave
5313 519847 21
ECU(Slave ECU)

140
 Appendix

Description Code SPN FMI

Message MS02 timeout error sent from Master ECU to Slave
5313 519847 26
ECU
Message MS02 timeout error sent from Master ECU to Slave
5313 519847 27
ECU(Slave ECU)
Message MS02 byte error sent from Master ECU to Slave ECU 5313 519847 24
Message MS02 byte error sent from Master ECU to Slave
5313 519847 25
ECU(Slave ECU)
Message MS03 timeout error sent from Master ECU to Slave
5313 519847 30
ECU
Message MS03 timeout error sent from Master ECU to Slave
5313 519847 31
ECU(Slave ECU)
Message MS03 byte error sent from Master ECU to Slave ECU 5313 519847 28
Message MS03 byte error sent from Master ECU to Slave
5313 519847 29
ECU(Slave ECU)
Message MS04 timeout error sent from Master ECU to Slave
5313 519631 2
ECU
Message MS04 timeout error sent from Master ECU to Slave
5313 519848 1
ECU(Slave ECU)
Message MS04 byte error sent from Master ECU to Slave ECU 5313 519631 14
Message MS04 byte error sent from Master ECU to Slave
5313 519848 0
ECU(Slave ECU)
Message MS14 timeout error sent from Master ECU to Slave
5313 519848 22
ECU
Message MS14 timeout error sent from Master ECU to Slave
5313 519848 23
ECU(Slave ECU)
Message MS14 byte error sent from Master ECU to Slave ECU 5313 519848 20
Message MS14 byte error sent from Master ECU to Slave
5313 519848 21
ECU(Slave ECU)
Message MS15 timeout error sent from Master ECU to Slave
5313 519848 26
ECU
Message MS15 timeout error sent from Master ECU to Slave
5313 519848 27
ECU(Slave ECU)
Message MS15 byte error sent from Master ECU to Slave ECU 5313 519848 24
Message MS15 byte error sent from Master ECU to Slave
5313 519848 25
ECU(Slave ECU)
Master ECU top dead center angle calculation failed 1341 519861 28
Master ECU top dead center angle is abnormal 1341 519861 29
Master ECU and slave ECU fault mutual transmission signal 01
5313 518100 2
timeout
Master ECU and slave ECU fault mutual transmission signal 01
5313 518100 14
length error.

141
Appendix

Description Code SPN FMI

Master-slave ECU identity verification does not pass 1432 519858 16
Master-slave ECU signal error 5434 519858 15
Master and slave ECU signal status is the same fault 5434 519858 14
Master-slave oil temperature deviation is too large 1133 175 0
Master-slave oil pressure deviation is too large 1133 100 0
Master-slave intake manifold pressure deviation is too large 2132 102 11
Master-slave intake air temperature deviation is too large 2144 519868 27
Master and slave software version number verification is not
1432 519861 26
trusted
Coolant temperature divination between Master ECU and Slave
1111 110 18
ECU is too large
Master-slave synchronization status signal verification is not
5434 519861 27
trusted
Active valve high rail pressure shock to establish monitoring 1233 517670 8
Active valve pressure rise monitoring 1233 517670 14
Short circuit to ground error at actuator relay_0 5213 3598 4
Short circuit to ground error at actuator relay_0 5213 3599 4
Short circuit to ground error at actuator relay_0(Slave ECU) 5213 519843 21
Short circuit to ground error at actuator relay_0(Slave ECU) 5213 519843 22
Short circuit to battery error at actuator relay_0 5213 3598 3
Short circuit to battery error at actuator relay_0 5213 3599 3
Short circuit to battery error at actuator relay_0(Slave ECU) 5213 519843 12
Short circuit to battery error at actuator relay_0(Slave ECU) 5213 519843 13

142
 Appendix

6.5 Recommended Torques for Bolts

6.5.1 Recommended Torques for Hollow Bolts

Specification Head type Recommended tightening torque (N·m)

M8×1 Hexagon head 7±1

17±2
Hexagon head
M10×1 13±2 (Copper bolt and small combination washer)

Flange bolt 20±3

Hexagon head 22±3

M12×1.5
Flange bolt 28±3

Hexagon head 27±3

M14×1.5
Flange bolt 32±3

Hexagon head 30±3

M16×1.5
Flange bolt 36±3

M18×1.5 Hexagon head and flange bolts 60±5

143
Appendix

6.5.2 Recommended Torques for Standard Bolts

Friction coeffi-
0.125 (zinc plated) 0.14 (polished)
cient

Strength grade 6.9 8.8 10.9 12.9 6.9 8.8 10.9 12.9

Bolt size Recommended torque (N·m)

M4 2.3 2.7 3.8 4.6 2.4 2.9 4.1 4.9

M5 4.7 5.5 8.0 9.5 5.0 6.0 8.5 10

M6 8.0 9.5 13.0 16.0 8.5 10 14.0 17

M8 19 23 32 39 21 25 35 41

M10 39 46 64 77 41 49 69 83

M12 67 80 110 135 72 86 120 145

M14 105 125 180 215 115 135 190 230

M16 165 195 275 330 180 210 295 355

M18 225 270 390 455 245 290 405 485

M20 325 385 540 650 345 410 580 690

M22 435 510 720 870 465 550 780 930

M24 560 660 930 1100 600 710 1000 1200

M27 830 980 1400 1650 890 1050 1500 1800

M30 1100 1350 1850 2250 1200 1450 2000 2400

M8×1 21 25 35 42 23 27 38 45

M10×1.25 41 49 66 82 44 52 73 88

M12×1.25 74 88 125 150 80 95 135 155

M12×1.5 70 83 115 140 76 90 125 150

M14×1.5 115 140 195 235 125 150 210 250

M16×1.5 175 210 295 350 190 225 315 380

M18×1.5 255 305 425 510 275 325 460 550

M20×1.5 360 425 600 720 385 460 640 770

M22×1.5 480 570 800 960 520 610 860 1050

M24×1.5 610 720 1000 1200 650 780 1100 1300

M27×1.5 890 1050 1500 1800 970 1150 1600 1950

M30×1.5 1250 1450 2050 2500 1350 1600 2250 2700

144
 Index

Index
A
Air heating .......................................................................................................................... 43

B
Before any operation or maintenance on any Baudouin product ...................................... 11

C
Charging Circuit ................................................................................................................. 41
Cooling Circuits for 4M06 Series Diesel Engine Overall Layout ....................................... 20
D
Diagnostic Fault Codes List for 4M06CR ........................................................................ 107
Diagnostic Fault Codes List for 4M06CR ........................................................................ 120

E
Engine Plate....................................................................................................................... 17
Engine Start-up after a Long-term Storage ....................................................................... 82
ECU for 4M06 .................................................................................................................... 25
F
Fuel circuit diagram of 4M06CR ........................................................................................ 23
Fuel circuit diagrams of 4M06MP ...................................................................................... 24
Fuel circuit diagrams of 12M33MP .................................................................................... 24
Fuel circuit diagrams of 14M06CR ........................................................................................
Fuel line ............................................................................................................................. 40
Fuel pre-supply pump ............................................................................................................
Fuel Tank............................................................................................................................ 40

L
Lifting device ...................................................................................................................... 34
Lifting Points ...................................................................................................................... 34
Lifting the engine ............................................................................................................... 34

M
M1 Maintenance Operations ............................................................................................. 90
M2 Maintenance Operations ............................................................................................. 73
M3 Maintenance Operations ............................................................................................. 74

P
Parking solenoid valve ...........................................................................................................
Preparing the Engine for a Long-term Storage ................................................................. 82

145
Index

Schematic Diagrams of 4M06CR ...................................................................................... 18

Schematic Diagrams of 4M06MP ...................................................................................... 19
Sensors .............................................................................................................................. 43
Starting the Engine ............................................................................................................ 12
Startup Circuit .................................................................................................................... 41
Stopping the Engine .......................................................................................................... 12

T
Troubleshooting ................................................................................................................. 93

Index .................................................................................................................................. 93

146
Contact Us

Baudouin
Address: Moteurs Baudouin, Technoparc du Bregadan, 13260 Cassis, France
Website: Baudouin.com
Aftersales Service Center: [email protected]
©2018 Société International des Moteurs Baudouin
All Rights Reserved

147