Lenovo D1960W

18.
5” LCD Color Monitor Lenovo D1960W
Service
Service
Service
Horizontal Frequency
30-65 kHz
TABLE OF CONTENTS
Description Page Description Page
Table Of Contents.......……..............................…........1 6.Schematic…………………...................................…17

Revision List.…........................................……......2 6.1.Main Board.................................................17
Important Safety Notice.…….........................……......3 6.2.Power Board....……….…....................................21
1.Monitor Specification..............................………........4 6.3.Key Board....……….…....................................23
2.LCD Monitor Description…………………………….......5 7.PCB Layout..……………….......................................24
3.Operation Instruction……………...............……...........6 7.1.Main Board……………........................................25
3.1.General Instructions………..........................…...........6 7.2.Power Board….......................................26
3.2.Control Button…………….…..............……...............6 7.3.Key Board…………...…….....................................27
3.3.Adjusting the Picture...........................…............6 8.Maintainability…………….........................................28
4.Input/Output Specification............……………............9 8.1.Equipments and Tools Requirement...............29
4.1.Input Signal Connector............………….................9 8.2.Trouble Shooting…………..............................30-35
4.2.Factory Preset Display Modes.........................10 9.White-Balance Luminance adjustment………….....36
N
4.3.Panel Specification.....……...……………..................10 10.Monitor Exploded View……………………….........38
5.Block Diagram………...................…………................12 11.BOM List….....................................................39-51
5.1.Software Flow Chart…………………………...........13
5.2.Electrical Block Diagram…………………..….......15
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
1
18.5” LCD Color Monitor Lenovo D1960W
Revision List
Version Release Date Revision History TPV Model Name
A00 JUE.25. 2009 Initial release T8RCM6NQXNNR6NJ
Important Safety Notice

Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
2
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:

DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
3
1. Monitor Specifications
4
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board and a key board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Monitor Block Diagram
Flat Panel and

CCFL Drive.
CCFL backlight
RS232 Connector
Power board
Main Board For white balance
(Include: adapter, inverter)
adjustment in factory
mode
Key board
AC-IN Video signal, DDC

90V-264V
HOST Computer
5
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The control buttons are located on the right side of the
monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
- The power cord should be connected.
- Connect the video cable from the monitor to the video card.
- Press the power button to turn on the monitor, the power indicator will light up.
3.2 Control Buttons
6
3.3 Adjusting the Picture
7
8
4. Input/Output Specification
4.1 Input Signal Connector
1 5
6 10
11 15
Pin No. Description Pin No. Description
1. Red Input 9. +5VDC
2. Green Input 10. GND
3. Blue Input 11. GND
4. GND 12. SDA
5. Connection detect 13. H Sync
6. Red GND 14. V Sync
7. Green GND 15. SCL
8. Blue GND
Pin No Description Pin No Description
1 TMDS data2- 13 TMDS data3+

2 TMDS data2+ 14 +5V
3 TMDS data2/4 shield 15 To check signal cable connected or not.
4 TMDS data4- 16 Hot Plug Detect
5 TMDS data4+ 17 TMDS data0-
6 DDC Clock 18 TMDS data0+
7 DDC data 19 TMDS data0/5 shield
8 Analog Vertical Sync 20 TMDS data5-
9 TMDS data1- 21 TMDS data5+
10 TMDS data1+ 22 TMDS clock shield
11 TMDS data1/3 shield 23 TMDS clock+
12 TMDS data3- 24 TMDS clock-
9
4.2. Factory Preset Display Modes
Addressability Refresh rate
640x480 60Hz 66Hz 72Hz 75Hz
700x570 50Hz
640x400 70Hz
720x400 70Hz
800x600 60Hz 72Hz 75Hz
1024x768 60Hz 70Hz 75Hz
1360x768 60Hz
1366x768 60Hz
4.3 Panel Specification

This specification applies to the 18.5 inch-wide color a-Si TFT-LCD module CLAA185WA02 .The display supports
the WXGA-1366(H)x768(V)screeen format and 16.7M colors(RGB 6-bits+Hi-FRC data).All input signals are
1-channel LVDS interface and this module doesn’t contain an inverter board for backlight.
4.3.1 Features
- Super Wide viewing angle.
- Super High contrast ratio
- Super fast response time
- High color saturation
- WXGA+ (1366 x 768 pixels) resolution
- 16.7M colors
- LVDS (Low Voltage Differential Signaling) interface
- RoHS Compliance
10
4.3.2 Display Characteristics
4.3.3 Optical Characteristics (The optical characteristics are measured under stable conditions 25°C):
11
4.3.4 Electrical Characteristics
1. TFT LCD Module
2. Backlight Units
12
5. Block Diagram
5.1 Software Flow Chat
Y
2 3
5 N
N
7 8
10 N
11
N 12 13 N
Y Y
N
14 15 16
17
N
18 19
13
1) MCU initialize.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to blue color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappear.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
14
5.2 Electrical Block Diagram
5.2.1 Main Board
Crystal14.31818MHz LCD PANEL

(X401) (CN301)
EPR_SDA
FLASH ROM
EPR_SCL Scalar IC TSUM5PFHL-LF MSTAR
SST25LF020A
(Include ADC, OSD, MCU)
(U402)
(U401)
H sync
V sync
RGB
Key Board DVI EEPROM

D-Sub
Control Connector M24C04-WMN6TP
Connector
(CN001) (CN102) (U403)
(CN101)
DB15_SDA DVI_SDA
DB15_SCL DVI_SCL
EEPROM EEPROM
M24C02-WMN6TP M24C02-WMN6TP
(U101) (U102)
15
5.2.2 Inverter/Power Board
5V Rectifier
and Filter
Bridge Transformer
Rectifier and T901
EMI filter Filter 12V Rectifier
and Filter
Start Circuit: R904，R932，R933 CN902
5V
Over Feedback
PWM Control IC
Voltage Circuit 12V
IC LD7552BPS
Protect
ON/OFF
MOSFET
Output Transformer
Q802、Q803
Lamp Circuit
Feedback PWM Control ON/OFF Control

Circuit Over IC TL494IDR
Voltage
Q805/Q808
Protect
DIM Control
16
6. Schematic
6.1 Main Board
715G2883 1 6
FB102
MVCC_1 VGA_B+ 1 2 R105 100R 1/16W 5% C102

BEAD 0.047uF DSUB_B+ 2
1
H_Sy nc R102 0R05 1/10W 5% R103 1K 1/16W 5% R108 C105
DSUB_H 2
V_Sy nc R104 1K 1/16W 5% 5pF/50V
DSUB_V 2
D109 75R 1/16W 5%
R106 R107 C103 C104 BAT54C VGA_B- R109 100R 1/16WC106

5%
DSUB_B- 2
0.047uF
2K2 1/16W 5% 2K2 1/16W 5% 22pF 22pF
3
DSUB_5V U104 ESD_VCC FB108 R110 470R 1/16W 5% C107
DSUB_SOG 2
DSUB_SCL 1 6 H_Sy nc FB103 1000pF
2 I/O1 I/O4 5
CN101 DSUB_SDA 3 GNDVDD 4 V_Sy nc VGA_G+ 1 2 R111 100R 1/16W 5% C108
FB107 I/O2 I/O3 300 OHM BEAD 0.047uF DSUB_G+ 2
16
R101 10 AZC199-04S C112 R112 C109
DDC1_SCL DSUB_SCL 15 5 VGA_PLUG NC
FOR EMI 5pF/50V
2 DDC1_SCL
9 DSUB_5V 300 OHM 75R 1/16W 5%
100R 1/16W 5% 14 4 U1 03
8 VGA_B- C124 VGA_G- R114 100R 1/16W 5% C110
0.1uF 16V DSUB_G- 2
13 3 VGA_B+ ZD104 0.047uF
R113 7 VGA_G- RLZ5.6B ZD105
DDC1_SDA DSUB_SDA 12 2 VGA_G+ RLZ5.6B
2 DDC1_SDA U103
6 VGA_R- ESD_VCC
100R 1/16W 5% 11 1 VGA_R+ VGA_G+ 1 6 FB101
2 I/O1 I/O4 5
DB15 VGA_R+ 3 GNDVDD 4 VGA_B+ VGA_R+ 1 2 R115 100R 1/16W 5%C111
I/O2 I/O3 DSUB_R+ 2
17
BEAD 0.047uF
AZC199-04S C101 R116

NC C113
75R 1/16W 5% 5pF/50V
Prevent NC contact Discharge U1 01
VGA_R- R117 100R 1/16W 5%
C114
=> Connect NC Pin of CN101 Change VCC of U103 ~ U107 0.047uF
CMVCC
DSUB_R-
DSUB_5V
2
to GND from MVCC to ESD_VCC to
1
CN102
8
DVI_5V prevent without VCC issue. DVI_5V
D104
VSY NC 15 DVI_HPD BAT54C
SYNC GND 6 R118 100R 1/16W 5% DDC2_SCL
DDC SCL DDC2_SCL 2
7 R119 100R 1/16W 5% DDC2_SDA
DDC SDA DDC2_SDA 2
14 R120 10K 1/16W 5% R140
+5V 16
3
HPD NC R123 C116
11 C115 R121 NC NC
1/3shield 3 R122 HDCP_CTRL R124 R125
2/4shield 19 0.1uF/16V NC 2 4K7 1/16W 5% 4K7 1/16W 5% U101
0/5shield 22 Q101 NC 8 1
clk shield NC 7 VCC A0 2
18 R126 10R 1/16W 5% RX0P DDC1_SCL 6 WP A1 3
DAT0+ RX0P 2 SCL A2
17 R127 10R 1/16W 5% RX0N DDC1_SDA 5 4
DAT0- RX0N 2 SDA VSS
10 R128 10R 1/16W 5% RX1P DDC_WP
DAT1+ RX1P 2 2
9 R129 10R 1/16W 5% RX1N
DAT1- RX1N 2
2 R130 10R 1/16W 5% RX2P NC / M24C02-WMN6TP
DAT2+ RX2P 2
1 R131 10R 1/16W 5% RX2N
DAT2- RX2N 2 CMVCC FB104 FB105 DVI_5V
13
DAT3+ 12
DAT3- 5
DAT4+ 4
DAT4-
1
21 300 OHM 300 OHM
DAT5+ 20 C121 D108 C122
DAT5- 23 R132 10R 1/16W 5% RXCP 1000pF BAT54C
clk+ RXCP 2 1000pF
24 R134 10R 1/16W 5% RXCN VCC3.3
GND
GND
clk- RXCN 2
JACK
26
25
U107 ESD_VCC U105 ESD_VCC U106 ESD_VCC
3
AZC199-04S AZC199-04S AZC199-04S R133
1 6 1 6 1 6 10K 1/16W 5% C117
2 I/O1 I/O4 5 2 I/O1 I/O4 5 2 I/O1 I/O4 5 R136
3 GNDVDD 4 3 GNDVDD 4 3 GNDVDD 4 R137 R138 NC
I/O2 I/O3 I/O2 I/O3 I/O2 I/O3 DVI_HPD R135 10K 1/16W 5% NC U102
C120 C118 C119 4K7 1/16W 5% 4K7 1/16W 5% 8 1
7 VCC A0 2
NC NC NC VGA_PLUG R139 6K8 1/16W 5% DET_CABLE 2 DDC2_SCL 6 WP A1 3
DDC2_SDA 5 SCL A2 4
SDA VSS
U10 7 U1 0 5 U1 0 6 2 DDC_WP
GND POWER DGND NC / M24C02-WMN6TP
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Lenov o L197 Wide Size B
ESD_VCC2 FB109 ESD_VCC1
G2883-1C-3-X-11-080825 TPV MODEL T9RAM6D8LWGNHC Rev 1C
Key Component 2.0.INPUT PCB NAME
300 OHM < >
Date Tuesday , August 26, 2008 Sheet 2 of 6
17
CN301
PA[0..9] PB[0..9]
2 PA[0..9] 2 PB[0..9]
PB0 LVB3P LVB0M RXO0- 30
PA0 LVA3P PB1 LVB3M LVB0P RXO0+ 29
PA1 LVA3M PB2 LVBCKP LVB1M RXO1- 28
PA2 LVACKP PB3 LVBCKM LVB1P RXO1+ 27
PA3 LVACKM PB4 LVB2P LVB2M RXO2- 26
PA4 LVA2P PB5 LVB2M LVB2P RXO2+ 25
PA5 LVA2M PB6 LVB1P 24
PA6 LVA1P PB7 LVB1M LVBCKM RXOC- 23
PA7 LVA1M PB8 LVB0P LVBCKP RXOC+ 22
PA8 LVA0P PB9 LVB0M LVB3M RXO3- 21
PA9 LVA0M LVB3P RXO3+ 20
LVA0M RXE0- 19
LVA0P RXE0+ 18
17
LVA1M RXE1- 16
LVA1P RXE1+ 15
14
LVA2M RXE2- 13
CMVCC LVA2P RXE2+ 12
LVACKM RXEC- 11
LVACKP RXEC+ 10
U301 LVA3M RXE3- 9
1 8 LVA3P RXE3+ 8
R303 C302 2 S D 7 7
3 S D 6 6
10K 1/16W 5% 0.1uF/16V 4 S D 5 5
R304 G D 4
R302 NC\AO4411 PANEL_VCC 3
Q301 2
4K7 1/16W 5% 47K 1/16W 5% AO3401 1
C303
NC
R301 C301 CONN
Q302 C304
2 PPWR_ON# 2N3906S-RTK/PS PANEL_VCC 330 OHM 1/4W 0.1uF/16V
NC
R305
0 OHM +-5% 1/8W
+ C305
3D
100uF25V
Change the type

1 2
G S of resistor R301
AO3401L from 0805 to
1206.
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Lenov o L197 wide Size A
G2883-1c-3-X-11-080825 TPV MODEL T9RAM6D8LWGNHC Rev 1C

Key Component 3.0.OUTPUT PCB NAME
< >
18
CMVCC
VCC1.8
C710
0.1uF 16V
FB702
300 OHM
CN701 VCC3.3
C705 + C704
1 SM340A
2 D701 MVCC 0.1uF/16V 100uF25V
3 CMVCC Q702
4 CMVCC KN2907AS R705
5 BKLT-VBRI R709
6 BKLT-EN R710 NC NC 10K 1/16W 5%
7 PANEL_ID#
PANEL_ID# 2
8 Volume# Q703 R706
Volume# 2
9 Mute KN2907AS BKLT-VBRI
Mute 2 adj_BACKLIGHT 2
VCC3.3
300 OHM/NC R708 1K 1/16W 5%
FB704 NC
CONN C713 C701
lock type NC C712
0.1uF/16V NC
FOR EMI
R701
0R05 1/4W
DGND 1,2,3
VCTRL
DVI_5V DSUB_5V
1
D702
VCC3.3 VCC3.3 D702 External EDID NC

BAT54C
MVCC_1 Internal EDID BAT54C

R702
3
10K 1/16W 5% R703

FB701
BKLT-EN 10K 1/16W 5% FB703 C711
300 OHM
C702 0.1uF 16V NC
MVCC VCC3.3
NC R704
U701
on_BACKLIGHT 2
3 2
Q701 4K7 1/16W 5% VIN VOUT
VSS
2N3904S-RTK/PS
C707 R701 R708 U701
+ C706 C708 AP1117E33LA C709 +
1
100uF25V 0.1uF/16V 0.1uF/16V 100uF25V TSUM5PFHL 0R05 1/4W NC 223
TSUMU58EHL NC 3.3 OHM 2W 223
TSUMO58CWHL NC 3.3 OHM 2W 252

Both 223 and 252
foot-print
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Lenov o L197 wide Size B

Key Component 4.0.POWER PCB NAME
< >
19
VCC1.8 VDDC
VDDP FB403 VCC3.3 FB401 AVDD VCC3.3 FB402 VPLL
VCC3.3
4 VCC1.8
0 OHM +-5% 1/8W C412 300OHM 300OHM
1 VCC3.3
C409 C408
+ C403 C404 C406
C402 Del C209 C410 C411 0.1uF/16V C407 0.1uF/16V
10uF/50V 0.1uF/16V C405 10uF/50V 0.1uF/16V
0.1uF/16V VDVI VMPLL VPLL AVDD VDDP VDDC 0.1uF/16V 0.1uF/16V
0.1uF/16V 0.1uF/16V 0.1uF/16V
VCC3.3 FB404 VMPLL
14
98
16
24
32
49
56
75
51
66
82
34
8
VCC3.3 VDVI
81 VCC3.3
AVDD_MPLL
AVDD_PLL
VDDP
VDDP
VDDP
VDDP
AVDD_ADC
VDDC
VDDC
VDDC
VDDC
AVDD_DVI
AVDD_DVI
VCTRL VCTRL
300OHM R403
54 PA0 0 OHM +-5% 1/8W
23 LVA3P 55 PA1
1 DSUB_R+ RIN0P LVA3M
22 58 PA2 C414 C415
1 DSUB_R- RIN0M LVACKP
20 59 PA3 R402 0.1uF/16V 0.1uF/16V
1 DSUB_G+ GIN0P LVACKM
19 60 PA4 C413
1 DSUB_G- GIN0M LVA2P
21 61 PA5 NC 0.1uF/16V
1 DSUB_SOG SOGIN0 LVA2M
18 62 PA6
1 DSUB_B+ BIN0P LVA1P
17 63 PA7 R404 NC
1 DSUB_B- BIN0M LVA1M
27 64 PA8 Q405
1 DSUB_H HSY NC0 LVA0P
28 65 PA9 NC
1 DSUB_V VSY NC0 LVA0M
30
1 DDC1_SDA
31 DDCA_SDA/RS232_TX For detect LF_B
1 DDC1_SCL DDCA_SCL/rs232_RX
function,
3 R405 NC
1 RX2P R+ depend on
4
1 RX2N R-
6 PA[0..9] DVI_5V
1 RX1P
7 G+ PA[0..9] 3 FW DDC_WP 1
1 RX1N G- R447
9 R406
1 RX0P B+
10 67 PB0 PB[0..9] Q401
1 RX0N
12 B- LVB3P 68 PB1
PB[0..9] 3
NC
For RSTN detect
1
1
RXCP
RXCN
13 CK+
CK-
LVB3M
LVBCKP
69 PB2 NC function
100 70 PB3 NC R407 C416
1 DDC2_SDA DDCD_SDA LVBCKM
1 71 PB4 R446
1 DDC2_SCL DDCD_SCL LVB2P 72 PB5 NC NC
LVB2M 73 PB6 NC CMVCC MVCC
LVB1P 74 PB7
15 LVB1M 77 PB8
AVDD
R401 390 OHM 1/16W REXT LVB0P 78 PB9
LVB0M R448
0.1uF/16V 26
TSUMU58EHL-LF-1 36 20K OHM 1/16W
C417 REFP NC 45
VCC3.3 NC 46
25 NC
REFM 41 EE_WP Q406
GPIO_P23 42 AO3401
C401 GPIO_P22 R449
35 R445 100R 1/16W 5%/NC 30K OHM 1/16W 5%
U402 GPIO_P15/PWM0 PANEL_ID# 4
0.22uF16V 47 R409 100R 1/16W 5% WP
R412 1 8 37 PWM2/GPIO_P24 R410
CE# VDD SDO LVDS
10K 1/16W 5% 2 7 38 85
SO HOLD# SCZ GPIO_P12 on_BACKLIGHT 4
WP 3 6 39 86 6K8 1/16W 5%
WP# SCK SCK PWM1/GPIO_P25 adj_BACKLIGHT 4
4 5 40
VSS SI SDI 87
SST25LF020A-33-4C-SAE 48 RSTN 88 R415 100R 1/16W 5% KEY 1
3 PPWR_ON# GPIO_P27/PWM1 GPIO_P00/SAR1 89 R416 100R 1/16W 5% KEY 2
C419 GPIO_P01/SAR2 90 R417 100R 1/16W 5%
GPIO_P02/SAR3 DET_CABLE 1
84 C418 R413
+
MVCC RST 91 R419 120R 1/16W 5% LED_GRN/BLUE 3.9K 1/16W 5%

10uF/50V GPIO_P06 92 R420 120R 1/16W 5% LED_ORANGE 0.1uF/16V
R421 GPIO_P07 93 R422 NC
R423 PWM0/GPIO_P26 94
GPIO_P13 HDCP_CTRL 1
100K 1/16W 5% 0R05 1/16W 96 95 R424 100R 1/16W 5%/NC R426 CMVCC
Mute 4
2
C420 47pF XIN GPIO_P14 99 R425 100R 1/16W 5% POWER_KEY #

GPIO_P16/PWM2 VCC3.3
X401
14.31818MHz 10K 1/16W 5%
97
C421 47pF XOUT R427
1
R428 100R 1/16W 5%

NC/10K 1/16W 5%
C422 0.1uF/16V80
BY PASS FB406
R430
U402 44 R429 100R 1/16W 5% MSCL
NC
GPIO_P10/I2C_MCL 4 Volume#
43 R431 100R 1/16W 5% MSDA
GPIO_P11/I2C_MDA NC
For user data, WB, EDID, 52
SST HDCP are saved in Flash. 53 MODE[0] Q404
FOR EMI
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
MODE[1] NC
For WB, EDID, HDCP are

11
29
33
50
57
76
79
83
PMC
2
5
saved in Flash.
X'TAL
Normal Function : CL = Cs + ((Cg*Cd)/(Cg+Cd))
U402 P.S : Assume Cs = 4 pF Internal EDID External EDID
010A Befor AOC ID2007 OSD X401 CL of SPEC Cs and Cd (C420, C421) R406 NC 22K 1/16W 5%
020A For ID2008 (93G 22-53B-H) 18 pF 27 pF R407 NC 10K 1/16W 5%
(93G 22-53-J) 32 pF 56 pF C416 NC 0.1uF/16V
Q401 NC 2N3904S-RTK/PS
VCC3.3
R123 NC 10K 1/16W 5%
C423
R440 R441 R442 VCC3.3
R136 NC 10K 1/16W 5%
U403 0.22uF16V
10K 1/16W 5% 10K 1/16W 5% 10K 1/16W 5% 8 1
EE_WP 7 VCC NC 2
Max condition for LED:
WC E1
MSCL 6
SCL E2
3 1. Vcc = 3.3 V
MSDA 5 4 R444 R443
SDA VSS CN402 3.9K OHM 1% 1/16W 3.9K OHM 1% 1/16W 2. Current = 12 mA
M24C04-WMN6TP
FW need to be
1
2
KEY 2
KEY 1
modified.
3 POWER_KEY #
U403 R440 R441 R442 C423 4 LED_GRN/BLUE
5 LED_ORANGE
6
CN402 FB405 and C436
SST 7 LF_B
For user data, WB, EDID NC NC NC NC NC C431 C432 C433 C434 R411 C435 R408
C436
For Normal WAFER 2.0MM 6P NC
are saved in Flash. FB405 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 10K 1/16W 5% 0.1uF/16V 10K 1/16W 5%
CONN NC NC
For Philips WAFER 2.0MM 7P According to EMI
PMC 10K 10K 10K lock type
For WB, EDID are saved M24C04 1/16W 1/16W 1/16W 0.22uF/16V
in Flash. 5% 5% 5% TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Lenov o L197 wide Size C

K ey Component 5.0.SCALER PCB NAME
< >
20
6.2 Power Board
715G2852 3 4
R918
100 OHM 1/4W L904
R919 +12V
2
1 1.0uH
100 OHM 1/4W C912 ZD902
! R920
0.001uF
C922 R946
RLZ13B C930
+
+
100 OHM 1/4W + + 470UF/25V 150 OHM 2W 0.1uF
2 3 C917 C918
1
!T901
2
680uF/25V 680uF/25V
1 3 R943
BD901 Q903 470R 1/8W
-
D906
KBP208G 4 9 FCH10U10 PMBS3904
10
+ C907 R904 R905 R908
4
100uF450V 300K OHM 1/4W NC C906 D907 31DQ06FC3 L905 C932 R939
1500pF2KV 100KOHM +-5% 2WS 5 7 1K 1/8W
2
C904 ! C938
8 1.0uH
ZD923
0.001uF
NC R932 D900 11 R921 100 OHM 1/4W RLZ5.6B

0.22uF/275V 300K OHM 1/4W R906 FR107 6 12 F902
NC 2 C921 +
! ! 470uF/16V R948
+5V1
1
C902 C901 R922 100 OHM 1/4W
C910 + C939 56 OHM +-5% 2WS NC
1000pF 1000pF 0.001uF 820uF25V R947
2
1 470R 1/8W F904
R923 100 OHM 1/4W
C911 ZD906 D901 R909 POWER X'FMR 0R05 1/4W
0.1uF RLZ22B FR103 5.1 OHM 1/4W
+ C903
22uF/50V Q904 R952
D905 31DQ06FC3 PMBS3904 1K 1/8W
1
R933
300K OHM 1/4W R907
2
NC F903
L901 D903 R961 100 OHM 1/4W L903
30mH ! IC901
LL4148
! 1.0uH
+5V
4 5 NC
3 RT NC 6 Q901 R962 100 OHM 1/4W C929 + C940
2 VCC CS 7 R910 2SK2645-54MR 0.001uF 1000uF25V + F905
1
COMP VCC R924
2
1 8 10R 1/4W C915 0 OHM 1/4W
2
GND OUT R938 R935 100 OHM 1/4W 150R 1/8W 470uF/16V
1
ZD905 ZD922 ZD921
! LD7552BPS
RLZ18B
10K 1/8W
RLZ5.1B RLZ13B
C908 FB901
R915 BEAD
1
100K OHM 1% 1/8W R940
1
0.22uF/275V R912 33K 1/10W
R927
2
220 OHM 1/4W 3.6K OHM 1% 1/10W
1
R914 R925 D916
R902 C909 0.47 OHM +-5% 2WS ! IC902 1K 1/8W LL4148 D915
470pF/25V PC123X2Y FZOF LL4148
! 680K OHM 1/4W !
2
R900 R901
! 680K OHM 1/4W

680K OHM 1/4W
C924
C928 0.1uF R926 R942
0.01uF 1K 1/10W 1% 1K 1/10W 1%
IC903
C900 AZ431AZ-AE1
GND1 3300pF 250V
GND
VAR901
Varistor
! 1
2
C925 R930
2.43K OHM 1% 1/10W
NC
CN902
N.C
1
VOL
NR901 HS2 2
! NTCR HEAT SINK(D906_Q90G6263-3) MUTE
3
4
+5V
t ! ! 1
2 DIM
5
6
ON/OFF
7
C931 8
F901 0.1uF 9
FUSE 3.15A 250V HS5 10
SHIELD(H85G0002-1)
HS3
HEAT SINK(Q901_Q90G6263-3) 1 CONN
2
1
2
3
2 1 T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL AOC Q 15.6W Size Custom
G2852-1-X-X-2-080122 TPV MODEL PWPC7521MAD1 Rev 1

CN901 Key Component 2.POWER PCB NAME 715G2852-1
SOCKET ! Date Monday , September 08, 2008 Sheet 2 of 4
ODM MODEL
87G 501 32 S
21
1
2
C839 T801 CONN
R821
1500PF/50V POWER X'FMR R817
6 7 10K 1/10W 1% 1K 1/8W
CN801
R855 D805
15R 1/4W LL4148 C819
C801 2
F801 0.0022uF
3 30pF/3KV
+12V 4 3
1
0 OHM 1/4W C802
R804 Q801 470UF/25V + C824 R856 1 8 R801 D801
100R 1/8W PMBS3904 D810 0.1uF 15R 1/4W C803 1K5 1/10W 1% BAV99
NC Q802 30pF/3KV
AM9945N-T1-PF
1 8
Q808 S D
PDTA144WK 2 7 C838
Q805 G D 1500PF/50V
PDTC144WK R839 3 6 1
22R 1/8W S D 2
ON/OFF CONN
Q804 4 5 R822
2
PMBS3906 G D R828
C807 C825 1 10K 1/10W 1% 1K 1/8W
CN802
0.1uF/25V 0.1uF/25V
2
3
C823 3
D807
Q811 LL4148 0.0022uF 1
DIM
PMBS3904 R814
D811 1K5 1/10W 1% D802
NC BAV99
Q812 R850
2
PMBS3906 22R 1/8W
1
3
R827
1K 1/10W 1%
Q806 R853
PMBS3904 68K 1/10W
C835
NC
D817
LL4148
R841
68K OHM 1% 1/10W
C842
R851 0.01uF R829
6K8 1/10W R802 22R 1/8W
10K 1/10W 1%
R825
22R 1/8W
R837
47K 1/8W
R830 C822 R832 R807

NC 1uF/25V 10K 1/10W 1% TL494IDR 10K 1/10W 1%
IC801
1 16
D812 2 1IN+ 2IN+ 15
3 1IN- 2IN- 14
4 FEEDBACK REF 13 R818 D806
5 DTC OUTPUT CTRL 12 1K 1/10W 1% LL4148
6 CT VCC 11
LL4148 7 RT C2 10
R823 8 GND E2 9
0R05 1/10W 5% C1 E1
Q809
RK7002
C821 C846
0.1uF/25V R861 NC
R810 R865 NC R864 R854
51K OHM 1% 1/8W NC NC
NC C834 R835
R803 0.1uF/25V 1M 1/10W 5%
Q807 R826 R808 680K 1/10W
R820 N.C 1K 1/8W R824 10K 1/10W 1%
10K 1/10W 1% R863 R831 C820
10K 1/10W 1% 1K 1/8W 220pF50V 1K 1/10W 1%
C817 C845 R862

NC 2.2uF/16V 1M 1/10W 5% D814
LL4148
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL AOC Q 15.6W Size Custom
G2852-1-X-X-2-080122 TPV MODEL PWPC7521MAD1 Rev 1

Key Component 3.INVERTER PCB NAME 715G2852-1
ODM MODEL
Date Monday , January 21, 2008 Sheet 3 of 4
22
6.3 Key Board
715G3362-B
LED_RED#
3
LED001
LED
CN001
2
1 LBADC1 R002
2 LBADC2 2K OHM 1% 1/10W
3 DC_POWERON
4 LED_GRN#
5 LED_RED#
6
2
R004
C001 C002 ZD007 C003 C004 ZD008 C005 1K OHM 1% 1/10W
R005
0.001uF 0.001uF UDZSNP5.6B 0.001uF 0.001uF 0.001uF
UDZSNP5.6B 2K 1/10W 1%
Wire Harness
AUTO
SOURCE
SW002
SW006 SW005 SW004 SW003 SW SW001
1
+
-
SW SW SW SW SW
1 2 1 2 1 2 1 2 1 2 1 2
SGND ZD006 ZD002 ZD005 ZD003 ZD004 ZD001
2
C011
C007
C009
C010
C008
C006
3 4 3 4 3 4 3 4 3 4 3 4
NC/0.1uF
NC/0.1uF
NC/0.1uF
NC/0.1uF
NC/0.1uF
NC/0.1uF
UDZSNP5.6B UDZSNP5.6B UDZSNP5.6B UDZSNP5.6B UDZSNP5.6B UDZSNP5.6B
5 5 5 5 5 5
1
SGND
AUTO(2K) 1.11V
SGND SGND SGND SGND SGND SGND SGND SGND SGND SGND SGND
LBADC1
VOL- (GND) 0 V
VOL+(2K) 1.11V
LBADC2
GND
MENU(1K) 0.67V
SOURCE(GND) 0.65V
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Lenov o D185W Size B
G3362-1-X-X-1-081118 TPV MODEL SMTKEPC8JC8 Rev 1

Key Component Key board PCB NAME 715G3362-1
< >
Date Tuesday , Nov ember 18, 2008 Sheet 2 of 2
23
7. PCB Layout
7.1 Main Board
715G2883 1 6
24
25
7.2 Power Board
715G2852 2
26
27
7.3 Key Board
715G3355 1
28
8. Maintainability
8.1 Equipments And Tools Requirement
1. Voltmeter.
2. Oscilloscope.
3. Pattern Generator.
4. DDC Tool with Compatible Computer.
5. Alignment Tool.
6. LCD Color Analyzer.
7. Service Manual.
8. User Manual.
29
8.2 Trouble Shooting
8.2.1 Main Board
No power
Press power key and look if the

picture is normal
NG
Please reinsert and make sure the

5V input is normal
NG Reinsert or check the

OK
power section
Measure U703 Pin2=3.3V and Q702 PIN3(C)=1.8V
NG Check CN401 or replace U701,Q702

OK
Check X401 oscillate waveforms

are normal
NG
OK Replace X401
Check U401
30
(2) No picture
No picture
The button if under NG NG

X401 oscillate Replace X401
control waveform is normal
OK
OK
Check reset circuit of NG Check Correspondent
component
U401 is normal
Measure U701 PIN2=3.3V
and Q702 PIN3(C)=1.8V OK
Replace U402
OK
X401 oscillate NG
waveform is normal
Replace U701, Q702
NG
OK
Replace X401
Check HS/VS from

CN101 is normal
NG Check Correspondent
OK
component
Replace U401
31
(3) White screen
White screen
NG
Measure Q301 base X401 oscillate
waveform is normal
is low level?
OK NG Replace4201
OK
Check Q301,Q302 is Check reset circuit of

broken or CN301 solder? U202 is normal
NG Check Correspondent
Check Correspondent NG
component.
component.
OK
OK
Replace U401
Replace PANEL
32
8.2.2 Power/Inverter Board
No power
Check CN902 pin4, 5 = 5V
NG
Check AC line volt 110V or 220V
OK NG
Check AC input
Check the voltage of C907(+)
NG
Check bridge rectified circuit and F901 circut
OK
Check start voltage for the pin8 of IC901
NG
OK Check R904, R932, R933, and Change IC901
Check the auxiliary voltage is bigger than

10V and smaller than 20V
NG 1) Check IC901
OK
2) Check R909/D901/C903 and OVP circuit
Check IC901 pin8 PWM wave
NG
OK Check IC901,Q901
Check Q903/D906/IC902/ZD921/ZD922
33
W / LED, No Backlight
Check CN902 pin4, 5 = 5V
NG
OK Check the adapter and F904
Check ON/OFF signal and the pin 12 of IC801 is 12V
NG
Check main board or change ON/OFF signal
OK
Check the pin5 of IC801 have saw tooth wave
NG
OK Change IC801
Check the PWM wave from the pin9,10 of IC801
OK
Check IC801
Check Q802, Q803 PIN5, 6, 7, 8 have the NG Check Q801, Q804, Q811, Q812,
output of square wave at short time.
Q802, Q803
OK
NG
Check the output of T801, T802 Change T801
OK
Check connecter & lamp
34
8.2.3 Keypad Board
OSD is unstable or not working
N
Is Key Pad Board connecting normally? Connect Key Pad Board
N
Is Button Switch normally? Replace Button Switch
N
Is Key Pad Board normally? Replace Key Pad Board
Check Main Board
35
9. White- Balance, Luminance Adjustment
Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment.
Before started adjust white balance , please set the Chroma-7120 MEM Channel 3 to Reddish (6500K)
color, MEM Channel 4 to Default (7200K) color, MEM Channel 9 to Bluish (9300K) color , and MEM
2
Channel 10 to sRGB color ( our Reddish color parameter is x = 313 ±20, y = 329 ±20, Y=180±20cd/m ;
2
Default color parameter is x = 302 ±20, y = 318 ±20, Y=180±10cd/m ; Bluish color parameter is
2
x = 283 ±20, y = 297 ±20, Y=180±20cd/m ; sRGB color parameter is x = 313 ±20, y = 329 ±20,
2
Y=180±20cd/m )
How to setting MEM channel you can reference to chroma 7120 user guide or simple use “ SC” key and
“ NEXT” Key to modify xyY value and use “ID” key to modify the TEXT description Following is the procedure
to do white-balance adjust .
2. Setting the color temp. you want

A. MEM.CHANNEL 3 (Reddish color):
2
Reddish color temp. parameter is x = 313 ±20, y = 329 ±20, Y=180±20 cd/m
B. MEM.CHANNEL 4 (Default color):
2
Default color temp. parameter is x = 302 ±20, y = 318 ±20, Y=180±20cd/m
C. MEM.CHANNEL 9 (Bluish color):
2
Bluish color temp. parameter is x = 283 ±20, y = 297 ±20, Y=180±20cd/m
D. MEM.CHANNEL 10 (sRGB color):
2
sRGB color temp. parameter is x = 313 ±20, y = 329 ±20, Y= 180±20cd/m
3. Into Factory mode of Lenovo D185W:
Press the MENU button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the
left top of the panel.
4. Bias adjustment:
Set the Contrast to 50; Adjust the Brightness to 80.
5. Gain adjustment:
Move cursor to “-F-” and press MENU key
A. Adjust Reddish (6500K) color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM.channel to Channel 3 (with up or down arrow on chroma 7120)
2
3. The LCD-indicator on chroma 7120 will show x = 313 ±20, y = 329 ±20, Y=180±20 cd/m
4. Adjust the RED of color3 on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN of color3 on factory window until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE of color3 on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =100±2
B. Adjust Default (7200K) color-temperature
2. Switch the MEM.channel to Channel 4(with up or down arrow on chroma 7120)
2
3. The LCD-indicator on chroma 7120 will show x = 302 ±20, y = 318 ±20, Y=180±20cd/m
36
C. Adjust Bluish (9300K) color-temperature
1. Switch the Chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120)
2
3. The LCD-indicator on chroma 7120 will show x = 283 ±20, y = 297 ±20, Y=180±20cd/m
5. Adjust the GREEN of color1 on factory window until chroma 7120 indicator reached the value G=100
D. Adjust sRGB color-temperature
2. Switch the MEM.channel to Channel 10 (with up or down arrow on chroma 7120)
2
3. The LCD-indicator on chroma 7120 will show x = 313 ±20, y = 329 ±20, Y= 180 ±20cd/m
E. Turn the Power-button off to quit from factory mode.
37
18.5" LCD Color Monitor Lenovo D1960W
10. Monitor Exploded View
38
18.5"LCD Color Monitor Lenovo D1960W
11. BOM List
T8RCM6NQXNNR6NJ
Location Part number Description REMARK
007G 1 S 2 WOOD PALLET
040G 45762420A LABEL 25x6mm
040G 58162435A P/N LABEL FOR MANUAL PE BAG
040G 581654 3A CARTON LABEL
045G 77500 BARCODE RIBBON 2nd Source
045G 77501 BARCODE RIBBON 2nd Source
052G 1185 MIDDLE TAPE
052G 1186 SMALL TAPE
052G 1211527 Conductive Tape 75mm *45mm *0.08mm
070GHDCP500HDC HDCP CODE
078G 32210E K SPK 8 OHM 1.5W 43X18mm 250 100mm KUAIDA
E08904 089G 17356C554 AUDIO CABLE
E08904 089G 17356G554 AUDIO CABLE 2nd Source
E08904 089G 17356X554 AUDIO CABLE 2nd Source
E08902 089G 725CAA DB D-SUB CABLE
E08902 089G 725GAA DB D-SUB CABLE 2nd Source
E08902 089G 725HAA DB D-SUB CABLE 2nd Source
E08903 089G1745GAA AC DVI CABLE
E08903 089G1745HAA AC DVI CABLE 2nd Source
E08901 089G424A15N IS POWER CORD
E09502 095G8014 6D720 Wire Harness 6P(A1253)-6P(PH) 180mm
E09502 095G8014 6X720 Wire Harness 6P(A1253)-6P(PH) 180mm 2nd Source
E09501 095G8018 3XH39 LVDS CABLE 2nd Source
0M1G 130 5120 SCREW
0M1G1030 6120 SCREW M3X6
705GJ934010 支架组件
040G 45762420A LABEL 25x6mm

040G 581654 3A CARTON LABEL
XN01A AM1G1740 12 47 CR3 SCREW
Q34G0518AED 1L 909 STAND
Q37G0115012 hinge
E750 750GLC185WA211N000 PANEL CLAA185WA02 000 TW CPT 2nd Source
E750 750GLC185WA223N000 PANEL CLAA185WA02 011 FZ CPT 2nd Source
756GJ9CB LN001 MAIN BOARD-CBPCRM6PZB1J 2nd Source
U402 056G1133 81 SST25LF020A-33-4C-SAE
SMTCR-U402 100GLMC8000B11 MCU ASSY-56G1133 81
XN01A AM1G1740 12 47 CR3 SCREW
CN402 033G3802 6 WAFER
CN701 033G3802 9 WAFER 9P RIGHT ANELE PITCH
CN302 033G8027 14 H WAFER 14P 2.0MM DIP
040G 45762412B CBPC LABEL
39
049G 51 1A ERADICATOR
052G 2191 A PAPER TAPE
055G 2 ALCOHOL
055G 23524 WELDING FLUX WITHOUT PB
R708 061G152M229 64 2.2 OHM 2W 5% MOF
C419 067G 3151007KV ELCAP 10UF M 50V 105℃ KINGNICHI
C305 067G 3151014KV EC 105℃ CAP 100uF M 25V
CN101 088G 35315F XH D-SUB 15PIN VERTICAL CONN WITH SCREW

CN101 088G 35315F XH D-SUB 15PIN VERTICAL CONN WITH SCREW 2nd Source
CN102 088G 35424F D DVI 24PIN CONN F ATTACHED SCREW
CN102 088G 35424F J DVI 24PIN CONN F ATTACHED SCREW 2nd Source
CN102 088G 35424F N DVI 24PIN CONN F 附螺丝 2nd Source
X401 093G 22 53 J 14.31818MHZ/32PF/49US 2nd Source

X401 093G 22 53 YC Crystal 14.31818MHz/32PF 49U/S YC
C402 067G 3151007KB EC 10uF M 50V 5*11
C704 067G 3151014KB EC 100uF M 25V 6.3*11
C707 067G 3151014KB EC 100uF M 25V 6.3*11
C706 067G 3151014KB EC 100uF M 25V 6.3*11
052G6026 3 MESH PRINTTING PAPER
055G 23520 IPA
055G 100610 TIN CREAM W/O PB
U401 056G 562558 1 IC TSUM5PFHL-LF MSTAR
U701 056G 585 4A IC AP1117E33L-13
U107 056G 662 13 IC AZC099-04S SOT23-6L
U106 056G 662 13 IC AZC099-04S SOT23-6L
U105 056G 662 13 IC AZC099-04S SOT23-6L
U104 056G 662 13 IC AZC099-04S SOT23-6L
U103 056G 662 13 IC AZC099-04S SOT23-6L
U403 056G1133 32 IC M24C04-WMN6TP SO8
U402 056G1133 81 SST25LF020A-33-4C-SAE
Q404 057G 417 12 T KEC 2N3904S-RTK/PS
Q701 057G 417 12 T KEC 2N3904S-RTK/PS
Q302 057G 417 13 T KEC 2N3906S-RTK/PS 2nd Source
Q703 057G 417 16 T MMBT2907
Q702 057G 417 16 T MMBT2907
Q302 057G 417517 Tra LMBT3906LT1G -200mA/-40V SOT-23 LRC
Q404 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC 2nd Source
Q701 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC 2nd Source
Q406 057G 763 1 A03401 SOT23 BY AOS(A1)
U301 057G 763 3 AO4411 SO-8
40
R423 061G0402000 RST CHIP MAX 0R05 1/16W
R134 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R132 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R131 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R130 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R129 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R128 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R127 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R126 061G0402100 RST CHIPR 10 OHM +-5% 1/16W
R114 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R115 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R113 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R111 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R109 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R105 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R101 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R424 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R431 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R429 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R428 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R425 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R422 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R417 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R416 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R117 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R118 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R119 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R415 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R409 061G0402101 RST CHIPR 100 OHM +-5% 1/16W
R706 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W
41
R419 061G0402121 RST CHIP 120R 1/16W 5%
R420 061G0402121 RST CHIP 120R 1/16W 5%
R106 061G0402222 RST CHIPR 2.2 KOHM +-5% 1/16W
R401 061G0402390 0F RST CHIP 390R 1/16W 1%
R444 061G0402390 1F RST CHIPR 3.9KOHM +-1% 1/16W
R443 061G0402390 1F RST CHIPR 3.9KOHM +-1% 1/16W
R110 061G0402471 RST CHIPR 470 OHM +-5% 1/16W
R139 061G0402682 RST CHIP 6K8 1/16W 5%
R410 061G0402682 RST CHIP 6K8 1/16W 5%
R116 061G0402750 RST CHIPR 75 OHM +-5% 1/16W
R112 061G0402750 RST CHIPR 75 OHM +-5% 1/16W
R108 061G0402750 RST CHIPR 75 OHM +-5% 1/16W
R102 061G0603000 RST CHIP MAX 0R05 1/10W
FB403 061G0805000 F RST CHIPR 0 OHM +-5% 1/8W FENGHUA
R305 061G0805000 F RST CHIPR 0 OHM +-5% 1/8W FENGHUA
R403 061G0805000 F RST CHIPR 0 OHM +-5% 1/8W FENGHUA
R301 061G1206331 RST CHIPR 330 OHM +-5% 1/4W
C107 065G0402102 32 1000PF +-10% 50V X7R
C121 065G0402102 32 1000PF +-10% 50V X7R
C122 065G0402102 32 1000PF +-10% 50V X7R
C124 065G0402104 12 CAP CHIP 0402 0.1UF 16V X7R
C710 065G0402104 12 CAP CHIP 0402 0.1UF 16V X7R
C711 065G0402104 12 CAP CHIP 0402 0.1UF 16V X7R
C414 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C415 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C417 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C418 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C422 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C431 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C432 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C433 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
42
C434 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C435 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C701 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C705 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C708 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C709 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C115 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C301 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C302 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C403 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C404 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C405 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C406 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C407 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C408 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C409 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C410 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C411 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C412 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C413 065G0402104 15 MLCC 0402 0.1UF K 16V X5R
C104 065G0402220 31 CHIP 22PF 50V NPO
C103 065G0402220 31 CHIP 22PF 50V NPO
C423 065G0402224 17 CAP CER 0.22UF -20%-80%
C401 065G0402224 17 CAP CER 0.22UF -20%-80%
C421 065G0402470 31 MLCC 0402 CAP 47PF J 50V NPO
C420 065G0402470 31 MLCC 0402 CAP 47PF J 50V NPO
C114 065G0402473 12 CHIP 0.047uF 16V X7R
C111 065G0402473 12 CHIP 0.047uF 16V X7R
C110 065G0402473 12 CHIP 0.047uF 16V X7R
C108 065G0402473 12 CHIP 0.047uF 16V X7R
C106 065G0402473 12 CHIP 0.047uF 16V X7R
C102 065G0402473 12 CHIP 0.047uF 16V X7R
C113 065G0402509 31 CHIP 5pF 50V NPO
C109 065G0402509 31 CHIP 5pF 50V NPO
C105 065G0402509 31 CHIP 5pF 50V NPO
FB702 071G 56G301 EA BEAD 300 欧
FB401 071G 56V301 B CHIP BEAD FCM2012VF-301T07 bullwill 2nd Source

FB404 071G 56V301 M CHIP BEAD 2012 300 OHM
FB104 071G 59G301 CHIP BEAD 300OHM
43
FB101 071G 59K190 B 19 OHM BEAD
FB102 071G 59K190 B 19 OHM BEAD
FB103 071G 59K190 B 19 OHM BEAD
D109 093G 60505 DIO SIG SM BAT54C(PHSE)R
ZD105 093G 39GA01 T RLZ5.6B
ZD104 093G 39GA01 T RLZ5.6B
D701 093G3004 3 SM340A
715G2883 1 6 MAIN PCB FR-4 D/S 80X72MM
Q05G6054 1 SHEET
Q55G 100622 TIN STICK(SAC0507)
Q55G 100625 TIN STICK_LOW ARGENTUM
J07G 1 S 99 WOODER PALLET
J11G 800 5 支撑钉
J40G 19T60814A ID LABEL D1960

J40G 586625 5A CARTON LABEL L174 LI
J44G6000624 9A EMPTY CARTON FOR SKD
J44G6002 S110 PAPER PLATE FOR SKD
J44G6002 S150 PAPER PLATE
J44G6002624 1A EMPTY CARTON FOR SKD
J44G6002SKD 6A CLAPBOARD FOR SKD
J45G 76 28IB3 C pe bag for manual/card
J45G 77 6 PE PACKING
J45G 88196 B PE FILM
J70G190160811B CD MANUAL D1960
KEPC8QN7J KEPC BOARD
CN1 033G8032 6F S HR CONNECTOR
R005 061G0603100 1F RST CHIPR 1 KOHM +-1% 1/10W
C003 065G0603104 32 CHIP 0.1UF 50V X7R
C004 065G0603104 32 CHIP 0.1UF 50V X7R
SW001 077G 607 1 CJ TACT SWITCH
44
SW001 077G 607 1 FD TACT SWITCH 2nd Source
LED001 081G 14 12 GP LED
715G3355 1 KEY PCB FR-4 D/S 102.1X13MM
PWPC8521CL1CKDJ g2852-3-4-X-1-090603(L)
CN602 033G3802 4 DH L WAFER 2nd Source
CN602 033G3802 4 DH JF WAFER
CN802 033G8021 2E F WAFER 2nd Source
CN801 033G8021 2E F WAFER 2nd Source
CN801 033G8021 2E U INVERT CONNECTOR 2nd Source
CN802 033G8021 2E U INVERT CONNECTOR 2nd Source
CN801 033G8021 2E XY CONNECTOR
CN802 033G8021 2E XY CONNECTOR
040G 45762412B CBPC LABEL
IC902 056G 139 3A IC PC123Y22FZ0F
IC601 056G 616 34 IC APA2069JITUL 2.6W*2 PDIP-16
NR901 061G 58080 N RST NTCR 8OHM SHAGON
NR901 061G 58080 WT 8 OHM NCT 2nd Source
C908 063G 10722410V 0.22UF 275VAC ARCO 2nd Source
C904 063G107K104 6 0.1UF +-10%
C904 063G107K104 U 0.1UF/275V 2nd Source
C908 063G107K224 US MPX. 0.22UF 250V +_10%
C908 063G107K2246S1 X2 CAP 0.22UF K 275VAC 2nd Source
C801 065G 3J2206ET 22PF 5% SL 3KV TDK
C803 065G 3J2206ET 22PF 5% SL 3KV TDK
C901 065G305M1022BP Y2 1000PF M 250VAC Y5P
C902 065G305M1022BP Y2 1000PF M 250VAC Y5P
C900 065G306M2222BP 2200PF +-20% 250VAC
C907 067G 40Z10115K CAP 105 100UF M 450V 2nd Source
C907 067G 40Z10115X 100µF 450V
C922 067G215D4714KV E.C 105 CAP 470UF M 25V ED SERIES 2nd Source
C802 067G215D4714KV E.C 105 CAP 470UF M 25V ED SERIES 2nd Source
C918 067G215D6814KV CAP 105 680uF M 25V 2nd Source
C917 067G215D6814KV CAP 105 680uF M 25V 2nd Source
C939 067G215D8214KV EC 105 CAP 820UF M 25V
C940 067G215P1024XV CAP 105 1000UF M 25V
C921 067G215P4713XV CAP 105C 470UF M 16V
C915 067G215P4713XV CAP 105C 470UF M 16V
C922 067G215P4714XV CAP 105 470UF M 25V
C802 067G215P4714XV CAP 105 470UF M 25V
C918 067G215P6814XV CAP 105C 680UF M 25V
45
C917 067G215P6814XV CAP 105C 680UF M 25V
C940 067G215S1024KV EC 105 CAP 1000UF M 25V 2nd Source
L901 073G 174 65 H1 LINE FILTER 26mH MIN
L905 073G 253 91 V1 CHOKE COIL 1.1uH
L904 073G 253 91 V1 CHOKE COIL 1.1uH
L903 073G 253 91 V1 CHOKE COIL 1.1uH
L905 073G 253191 L CHOKE COIL 1.1uH CC-007802 2nd Source
T801 080GL17T 40 DN X'FMR TK.2001U.101 2nd Source
T901 080GL19T 26 T X'FMR 610uH SRW24LQL-T15H016 2nd Source
CN901 087G 501 32 S AC SOCKET 2nd Source
CN901 087G 501 32 DL AC SOCKET DIP 3PIN+2PIN GROUND
CN601 088G 30214K DC PHONE JACK 5PIN +开口向下弹片
BD901 093G 50460 28 BRIDGE DIODE KBP208G LITEON

D905 093G3006 1 1 31DQ06FC3 NIHON INTER
D907 093G3006 1 1 31DQ06FC3 NIHON INTER
CN902 095G 82510D531 10P(SCN)-9P(PH) 120MM 2nd Source
CN902 095G 82510W531 HARNESS 10P-9P 120MM
705GQ857020 Q901 ASS'Y
051G 200 1 OIL FOR DISAPPEAR
Q901 057G 667 30 2SK2645 2nd Source
Q901 057G 667906 MOSFET 9A/650V FMA09N65GX TO-220F
Q901 057G 724 11 STP9NK65ZFP 2nd Source
0M1G 930 8120 SCREW
HS3 Q90G6263 6 HEAT SINK
705GQ893028 D906 ASS'Y
051G 200 1 OIL FOR DISAPPEAR
D906 093G 60250 FCH10U10 2nd Source
D906 093G 60267 SP10100
0M1G 930 8120 SCREW
HS2 Q90G6263 6 HEAT SINK
IC801 056G 379 22 IC TL494IDR SOIC-16
IC901 056G 379107 IC LD7575A PS SOP-8
Q801 057G 417 4 PMBS3904/PHILIPS-SMT(04)
46
Q802 057G 600 55 P5506 HVG SO-8 2nd Source
Q809 057G 759 2 RK7002FD5T116 SOT-23 BY ROHM 2nd Source
Q808 057G 760 4A DTA144WN3/S SOT-23
Q808 057G 760 4B PDTA144WK SOT346 2nd Source
Q805 057G 760 5A DTC 144WN3/S SOT-23
Q805 057G 760 5B PDTC144WK SOT346 2nd Source
Q802 057G 763 14 AM9945N 2nd Source
Q809 057G 763511 MOSFET SRK7002LT1G SOT-23 LRC
Q802 057G 763525 APM9948K
Q802 057G 763525 APM9948K 2nd Source
R823 061G0603000 RST CHIP MAX 0R05 1/10W
R820 061G0603100 2F RST CHIPR 10K OHM +-1% 1/10W
R862 061G0603105 RST CHIPR 1M OHM +-5% 1/10W
R814 061G0603150 1F RST CHIPR 1.5 KOHM +-1% 1/10W
R930 061G0603243 1F RST CHIPR 2.43K OHM +-1% 1/10W
R861 061G0603270 3F RST CHIPR 270KOHM +-1% 1/10W
R927 061G0603360 1F RST CHIPR 3.6K OHM +-1% 1/10W
47
R853 061G0603683 RST CHIPR 68K OHM +-5% 1/10W
JR902 061G0805000 RST CHIP MAX 0R05 1/8W
R915 061G0805100 3F RST CHIPR 100KOHM +-1% 1/8W
R804 061G0805101 1ST CHIPR 100 OHM +-5% 1/8W
R608 061G0805109 RST CHIPR 1 OHM +-5% 1/8W
R924 061G0805151 RST CHIPR 150 OHM +-5% 1/8W
R825 061G0805220 RST CHIPR 22 OHM +-5% 1/8W
R829 061G0805220 RST CHIPR 22 OHM +-5% 1/8W
R839 061G0805220 RST CHIPR 22 OHM +-5% 1/8W
R850 061G0805220 RST CHIPR 22 OHM +-5% 1/8W
R943 061G0805471 RST CHIPR 470 OHM +-5% 1/8W
R947 061G0805471 RST CHIPR 470 OHM +-5% 1/8W
F904 061G1206000 RST CHIP MAX 0R05 1/4W
JR801 061G1206000 RST CHIP MAX 0R05 1/4W
F801 061G1206000 4 RST CHIP MAX 0R05 1/4W
F905 061G1206000 4 RST CHIP MAX 0R05 1/4W
R910 061G1206100 RST CHIPR 10 OHM +-5% 1/4W
R962 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R961 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R935 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R923 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R922 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R921 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R920 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R919 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R918 061G1206101 RST CHIPR 100 OHM +-5% 1/4W
R855 061G1206150 RST CHIPR 15 OHM +-5% 1/4W
R856 061G1206150 RST CHIPR 15 OHM +-5% 1/4W
R912 061G1206221 RST CHIPR 220 OHM +-5% 1/4W
R909 061G1206519 RST CHIPR 5.1 OHM +-5% 1/4W
48
C610 065G0603101 31 CER1 0603 NP0 50V 100P PM5 R
C611 065G0603101 31 CER1 0603 NP0 50V 100P PM5 R
C932 065G0603102 32 1000PF +-10% 50V X7R
C834 065G0603103 22 CHIP 10NF 25V X7R 0603
C842 065G0603103 32 CAP CHIP 0603 0.01UF K 50V X7R
C612 065G0603104 12 CER2 0603 X7R 16V 100N P
C613 065G0603104 12 CER2 0603 X7R 16V 100N P
C819 065G0603222 22 CHIP 2200PF 25V X7R
C823 065G0603222 22 CHIP 2200PF 25V X7R
C601 065G0603474 12 MLCC 0603 0.47UF K 16V X7R
C602 065G0603474 12 MLCC 0603 0.47UF K 16V X7R
C603 065G0603474 12 MLCC 0603 0.47UF K 16V X7R
C606 065G0603474 12 MLCC 0603 0.47UF K 16V X7R
C928 065G0805103 32 CAP CHIP 0805 10NF K 50V X7R
C931 065G0805104 32 CAP CHIP 0805 0.1uF K 50V X7R
C822 065G080510522K T CAP CHIP 0805 1UF K 25V X7R
C838 065G0805152 31 1.5nF/50V
C839 065G0805152 31 1.5nF/50V
C820 065G080522131G CAP CHIP 0805 220PF G 50V NPO
C845 065G080522512K T CAP CHIP 0805 2.2UF K 16V X7R
C909 065G0805471 21 CAP CHIP 0805 470PF J 25V NPO
C929 065G1206102 72 CAP CHIP 1206 1000PF K 500V X7R
D802 093G 6433S DIODE BAV99 SEMTECH
D801 093G 6433S DIODE BAV99 SEMTECH
ZD923 093G 39S 24 T RLZ 5.6B LLDS
ZD922 093G 39S 25 T RLZ5.1B LLDS
ZD902 093G 39S 40 T RLZ 13B LLDS
ZD921 093G 39S 40 T RLZ 13B LLDS
ZD905 093G 39S 44 T RLZ18B LLDS
D805 093G 64S522SEM LL4148
D806 093G 64S522SEM LL4148
49
D807 093G 64S522SEM LL4148
D812 093G 64S522SEM LL4148
D814 093G 64S522SEM LL4148
D817 093G 64S522SEM LL4148
D903 093G 64S522SEM LL4148
D915 093G 64S522SEM LL4148
D916 093G 64S522SEM LL4148
CN901 006G 31500 EYELET
IC903 056G 158 10 T IC AS431AZTR-E1 TO-92
IC903 056G 158 12 KIA431A-AT/P TO-92 2nd Source
R908 061G152M10452T RST MOFR 100KOHM +-5% 2WS
R946 061G152M15152T RST MOFR 150 OHM +-5% 2WS
R914 061G152M47852T RST MOFR 0.47 OHM +-5% 2WS
R948 061G152M56052T RST MOFR 56 OHM +-5% 2WS
C906 065G 2K152 2T6213 CAP CER 1500PF K 2KV 2nd Source
C906 065G 2K152 2T6921 CAP CER 1500pF K 2KV Y5P
C903 067G 2152207NT KY50VB22M-TP5 5*11 2nd Source
C903 067G215P2207PT CAP 105 22UF M 50V
C604 067G215Y1014KT EC CAP.105
C903 067G215Y2207KT CAP 105 22UF M 50V KINGNICHI 2nd Source
FB602 071G 55 9 T FERRITE BEAD
F901 084G 56 3 B FUSE 3.15A 250V
F901 084G 56 3W FUSE 2nd Source
D900 093G 6026T52T RECTIFIER DIODE FR107
D900 093G 6026W52T FR107 2nd Source
D901 093G 6038P52T PS102R 2nd Source
D901 093G 6038T52T FR103
J801 095G 90 23 JUMPER WIRE
50
715G2852 3 4 POWER-PCB FR-1 193*122*1.6MM 94V-0 SS
T801 S80GL17T40V 变压器 ASS'Y
T901 S80GL19T26V1 Transformer ASS'Y

Q12G6600 6 FOOT 2nd Source
Q15G0346Y01CKD MAIN FRAME
Q33G0279AED 1L POWER KEY 2nd Source
Q33G0280 1 1D LENS 2nd Source
Q33G0281 AS 1L BUTTON 2nd Source
Q33G0282 AS 1L DECORATE LEFT 2nd Source
Q33G0282 AS 2L DECORATE RIGHT 2nd Source
Q34G0520AEDC3L909C 18.5"BEZEL
Q34G0521ABJC2L 909 18.5"REAR COVER
Q34G0522ABJ 1L 909 REAR POWER COVER
Q34G0534AED 1L909C 18.5"BASE
Q34G0535 1 2P9090 DECORATE 2nd Source
Q40G000162410A S/N LABEL
Q41G780060847B STW L174W
Q44G6000 4E CKD Carton
Q45G 88609122 EPE BAG FOR MONITOR
E09501 S95G80183H39 LVDS ASS'Y
E09501 095G8018 3DH39 WIRE HARNESS 30P-14P 140mm 2nd Source
51

Lenovo D1960W

Uploaded by

Copyright:

Available Formats

Lenovo D1960W

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lenovo D1960W

Uploaded by

Copyright:

Available Formats

18.

5” LCD Color Monitor Lenovo D1960W

Table Of Contents.......……..............................…........1 6.Schematic…………………...................................…17

Version Release Date Revision History TPV Model Name

A00 JUE.25. 2009 Initial release T8RCM6NQXNNR6NJ

Important Safety Notice

FOR PRODUCTS CONTAINING LASER:

Monitor Block Diagram

Flat Panel and

AC-IN Video signal, DDC

3.2 Control Buttons

Pin No. Description Pin No. Description

1. Red Input 9. +5VDC

2. Green Input 10. GND

3. Blue Input 11. GND

4. GND 12. SDA

5. Connection detect 13. H Sync

6. Red GND 14. V Sync

7. Green GND 15. SCL

Pin No Description Pin No Description

1 TMDS data2- 13 TMDS data3+

640x480 60Hz 66Hz 72Hz 75Hz

800x600 60Hz 72Hz 75Hz

1024x768 60Hz 70Hz 75Hz

4.3 Panel Specification

Crystal14.31818MHz LCD PANEL

Key Board DVI EEPROM

Start Circuit: R904，R932，R933 CN902

Feedback PWM Control ON/OFF Control

MVCC_1 VGA_B+ 1 2 R105 100R 1/16W 5% C102

R106 R107 C103 C104 BAT54C VGA_B- R109 100R 1/16WC106

AZC199-04S C101 R116

to GND from MVCC to ESD_VCC to

U107 ESD_VCC U105 ESD_VCC U106 ESD_VCC

0 OHM +-5% 1/8W

Change the type

G2883-1c-3-X-11-080825 TPV MODEL T9RAM6D8LWGNHC Rev 1C

VCC3.3 VCC3.3 D702 External EDID NC

MVCC_1 Internal EDID BAT54C

10K 1/16W 5% R703

TSUMU58EHL NC 3.3 OHM 2W 223

TSUMO58CWHL NC 3.3 OHM 2W 252

G2883-1C-3-X-11-080825 TPV MODEL T9RAM6D8LWGNHC Rev 1C

VCC3.3 FB404 VMPLL

MVCC RST 91 R419 120R 1/16W 5% LED_GRN/BLUE 3.9K 1/16W 5%

C420 47pF XIN GPIO_P14 99 R425 100R 1/16W 5% POWER_KEY #

R428 100R 1/16W 5%

For WB, EDID, HDCP are

G2883-1C-3-X-11-080825 TPV MODEL T9RAM6D8LWGNHC Rev 1C

NC R932 D900 11 R921 100 OHM 1/4W RLZ5.6B

COMP VCC R924

! 680K OHM 1/4W

G2852-1-X-X-2-080122 TPV MODEL PWPC7521MAD1 Rev 1

R830 C822 R832 R807

C817 C845 R862

G2852-1-X-X-2-080122 TPV MODEL PWPC7521MAD1 Rev 1

SGND ZD006 ZD002 ZD005 ZD003 ZD004 ZD001

G3362-1-X-X-1-081118 TPV MODEL SMTKEPC8JC8 Rev 1

Press power key and look if the

Please reinsert and make sure the