Vincke Gear Pumps Cat

VINCKE HYDRAULICS
GEAR PUMPS
your Hydraulic Brand
Index
3
6
8
9
12
14
22
25
28
30
31
32
33
35
37
39
41
42
47
2
INTRODUCTION
Gear pumps from Vincke have a floating bushing feature with au-
tomatic axial clearance compensation. The bushings are made with
special abrasion resistant material providing improved service life.
Precisely machined gears ensure our units provide excellent low noi-
se characteristics. Our cold extrusion motor bodies can endure pres-
sures above 30Mpa. High strength cast iron front & rear covers also
enhance our reliability. Our units are widely used in the industrial,
mobile, marine and aerospace industries.
CHARACTERISTICS
Vincke gear pumps are produced in 5 different versions (G0, G1, 2P, 2.5P,
3P), and in each group different displacements are obtained by changing
the gears width.
• Pressure: VINCKE offers one pressure rating, please refer to charts.
• Efficiencies: volumetric up to 98%, mechanical up to 93%.
• Mountings: flanges, shaft ends and ports.
• Seals: Viton seals available.
• Integrate: all pumps can be ordered with relief valve and check valve.
Peak up to 30Mpa max. 3 sec.

Intermittent up to 28Mpa max. 25 sec.
Rated up to 25 Mpa
HYDRAULIC FLUIDS
Use specific mineral oil based hydraulic fluids having good • Place safety relief valve set at correct pressure and with good
antioxidant, anti-foaming(rapid de-aeration), anti-wear, anti- dynamic characteristic.
-corrosion and lubricating properties, Fluids should also com- • Recommended fluid speed in the inlet line—1.6 ̴ 5ft/s (0.5 ̴ 1.5m/s).
ply with DIN 51525 and VDMA 24317 standards and gel throu-
• Recommended fluid speed in the delivery line—6.5 ̴ 20ft/s (2 ̴
gh11th stage of FZG test.
6m/s).
For the standard models, the temperature of the fluid should
• Recommended fluid speed in the return line—5 ̴ 10ft/s (1.5 ̴ 3m/s).
range between 1ºC and 80ºC.
• Reservoir should have a capacity about twice as much as the
Fluid kinematic viscosity ranges are the following:
volume of delivered by the pump in one minute.
• The return and inlet pipe must be separated as far as possible
Allowed Range 6 ... 500 cSt and under the minimum level of the oil.
Recommended Range 1 ... 100 cSt • Install pump in a well cleaned environment, and make sure, prior
starting the system that all pipes and reservoir are perfectly
Value allowed at startup ... 2000 cSt
clean it is recommended to filter the new oil at 8-10um, before
filling the reservoir.
• Fill the pump with fluid before installing and check the direction
of rotation.
• Avoid shard restrictions and small radius bends.
• For the first run of the pump, it is advisable to disconnection the
pump discharge in order to purge the air from the system.
3
FILTER RECOMMENDATION
• By far largest number of premature failures of gear pumps is due

to contamination; filtering with clogging indicating and alarms are
recommended.
• The initial contamination of the fluid must not exceed class 10 NAS
1638,pass experience has shown that even brand new fluid often ex-
ceed this value in this case it is recommended below: 60µm inlet ,
and in the return side:
Standard P<2000PSI(14MPa) 2000PSI(14MPa)<P<3050PSI(21MPa) P>3050PSI(21MPa)

NAS1638 10 9 8
ISO4406 19/16 18/15 17/14
FILTER 25µm 20µm 10µm
PRESSURE DEFINITION INLET PRESSURE
P3= peak max. pressure Under standard working con-

p(bar)
P2= intermittent max. pressure
ditions, intake pipe pressure is
P1= continuous max. pressure
lower than atmospheric pressu-
P3
re. The operating inlet pressure
P2 should range between 0.7 and 3
P1 bars (absolute).
Max. 20 sec. Max. 2 sec.
ROTATION DIRECTION INLET AND DELIVERY LINES
Definition of rotation direction: When standing before the pump with dri- Intake lines 0,5 ... 1,6 m/s
ving shaft up with its projecting end towards the observer, the pump is
rotating clockwise in case of right-hand rotation “C”. The contrary will Delivery line 2 ... 6 m/s
happen with left-hand pumps “A”, keeping the same point of view. Return line 1,6 ... 3 m/s
4
DESIGN CALCULATIONS FOR PUMP
Q= flow rote (l/m)

M = torque
P = power
N = speed r/min
A = inside area of pipe (cm2)
v = Q / 6 • A (m/s)
V= displacement [cm3/rotation]
Fluid velocity
n = rota/ion speed [rotations per minute]
Calculate the velocity (v) of a fluid in a pipe as bellow:
ηvol = pump volumetric efficiency, take 0.95 as an indicative
value for rotation speeds ranging between 1.000 and 2000 v = Q / 6 • A (m/s)
rpm. Delivered flow rafe
ΔP = pressure differential (bar) Calculate flow rate (Q) as bellow:
ηhm = hydromechanical efficiency, take 0.80 as indicative Q = V • n • ηvol • 10-3 (L/min)
value under cold conditions and 0.85 under working condi- Absorbed torque
tions.
Calculate necessary torque (M) of a pump subject to pressu-
ηtot = total pump efficiency (ηhm • ηvol) re differential between inlet and delivery as bellow:
M = (V • Δp) / (62,8 • ηhm) (Nm)
Absorbed power
Calculate hydraulic power (P) transferred to fluid from a
pump subject to a pressure differential between inlet outlet
and delivery as bellow:
P = (q • Δp) / (612 • ηtot) (kW)
Values for ηvol and ηhm, and consequently ηtot depend
on pressure differential between inlet outlet and delivery,
rotation speed, fluid features (temperature and viscosity) and
filtering degree.
5
VNK0 GEAR PUMP G0
VNK0 GEAR PUMP

GROUP 0
End cover: G1 / 4 thread depth

12. To mount the pump, n.2 M5
screws, with a torque wrench
setting fixed at 5.4±0.5 Nm.
HOW TO ORDER
Single pump Group Size Shaft Flange Inlet port Outlet port Rotation
VNKB 0,5 0.19 01 B 38 OR C Clockswise

0.25 Counter
A
0.38 clockwise
0.5
0.75
1.00
1.25
1.5
1.75
2
6
VNK0 GEAR PUMP G0
Max. Min. Dimensions

Displacement Max. Pressure
Type Speed Speed M N
cm3/rev P1 P2 P3 r/min r/min mm mm
VNK-0-0.19-01-02-B-38-OR- 0.19 200 230 250 7000 1000 60 58.2
VNK-0-0.25-01-02-B-38-OR- 0.25 200 230 250 7000 1000 60,5 59
VNK-0-0.38-01-02-B-38-OR- 0.38 200 230 250 7000 1000 61,5 60.3
VNK-0-0.50-01-02-B-38-OR- 0.5 200 230 250 7000 1000 62,5 61
VNK-0-0.65-01-02-B-38-OR- 0.65 200 230 250 7000 1000 63,5 54,5
VNK-0-0.75-01-02-B-38-OR- 0.75 200 230 250 7000 1000 64,5 63.5
VNK-0-0.88-01-02-B-38-OR- 0.88 200 230 250 7000 1000 65,5 56,5
VNK-0-1-01-01-02-B-38-OR- 1,00 200 230 250 6000 850 66,5 66
VNK-0-1.25-01-02-B-38-OR- 1.25 200 230 250 500 700 68,5 68.5
VNK-0-1.5-01-02-B-38-OR- 1.5 200 230 250 400 600 70,5 70
VNK-0-1.75-01-02-B-38-OR- 1.75 180 210 230 4000 600 72,5 73
VNK-0-2-01-02-B-38-OR- 2 160 190 210 3000 500 74,5 75.5
7
VNK1 GEAR PUMP G1
VNK1 GEAR PUMP

GROUP 1
HOW TO ORDER
Single pump Group Size Shaft * Flange * Inlet port * Outlet port * Rotation
VNKB 1 0.8 * see specifications of shafts, C Clockswise

1.1 flanges and ports in pages 12, 13. Counter
A
1.3 clockwise
1.6
1.8
2.1
2.7
3.2
3.7
4.2
5
5.8
7
8
9.8
8
VNK1 GEAR PUMP G1
VNK1-*-02-B-38-OR
End cover: G3/8 thread depth

12. To mount the pump, n.2 M8
srews, with a torque wrench set-
ting fixed at 27±3 Nrn.

Type Speed Speed M L
cm /rev
3
P1 P2 P3 r/min r/min mm mm
VNK-1-0.8-02-B-38-OR- 0.8 250 270 290 6000 1000 73.5 61,5
VNK-1-1.1-02-B-38-OR- 1.1 250 270 290 6000 1000 74 62
VNK-1-1.3-02-B-38-OR- 1.3 250 270 290 6000 1000 75 63
VNK-1-1.6-02-B-38-OR- 1.6 250 270 290 6000 1000 76 64
VNK-1-1.8-02-B-38-OR- 1.8 250 270 290 6000 1000 77 65
VNK-1-2.1-02-B-38-OR- 2.1 250 270 290 6000 1000 78 66
VNK-1-2.7-02-B-38-OR- 2.7 250 270 290 6000 800 80 68
VNK-1-3.2-02-B-38-OR- 3.2 250 270 290 5000 800 82 70
VNK-1-3.7-02-B-38-OR- 3.7 250 270 290 4500 800 84 72
VNK-1-4.2-02-B-38-OR- 4.2 250 270 290 4000 800 86 74
VNK-1-4.8-02-B-38-OR- 4.8 230 250 270 3500 600 88 76
VNK-1-5.8-02-B-38-OR- 5.8 230 250 270 3000 600 92 80
VNK-1-5.8-02-B-38-OR- 7 210 230 250 2500 600 96 84
VNK-1-8.0-02-B-38-OR- 8 180 200 230 2100 600 100 88
VNK-1-9.8-02-B-38-OR- 9.8 150 170 190 2100 600 104 92
9
VNK1 GEAR PUMP G1
VNK1-*-02-B-38-38
M6 threads depth 12. To mount

the pump, n.2 M8 screws, with a
torque wrench setting fixed at 27
±3 Nm.

Type Speed Speed M N L
cm /rev
3
P1 P2 P3 r/min r/min mm mm mm
VNK-1-0.8-02-B-38-38- 0.8 250 270 290 6000 1000 73.5 61,5 32.8
VNK-1-1.1-02-B-38-38- 1.1 250 270 290 6000 1000 74 62 33
VNK-1-1.3-02-B-38-38- 1.3 250 270 290 6000 1000 75 63 33.5
VNK-1-1.6-02-B-38-38- 1.6 250 270 290 6000 1000 76 64 34
VNK-1-1.8-02-B-38-38- 1.8 250 270 290 6000 1000 77 65 34.5
VNK-1-2.1-02-B-38-38- 2.1 250 270 290 6000 1000 78 66 35
VNK-1-2.7-02-B-38-38- 2.7 250 270 290 6000 800 80 68 36
VNK-1-3.2-02-B-38-38- 3.2 250 270 290 5000 800 82 70 37
VNK-1-3.7-02-B-38-38- 3.7 250 270 290 4500 800 84 72 38
VNK-1-4.2-02-B-38-38- 4.2 250 270 290 4000 800 86 74 39
VNK-1-4.8-02-B-38-38- 4.8 230 250 270 3500 600 88 76 40
VNK-1-5.8-02-B-38-38- 5.8 230 250 270 3000 600 92 80 42
VNK-1-5.8-02-B-38-38- 7 210 230 250 2500 600 96 84 44
VNK-1-8.0-02-B-38-38- 8 180 200 230 2100 600 100 88 46
VNK-1-9.8-02-B-38-38- 9.8 150 170 190 2100 600 104 92 48
10
VNK1 GEAR PUMP G1
VNK1-*1-1
M6 thread depth 12. To mount

the pump, n.4 MB screws, with
a torque wrench setting fixed at
27 ±3 Nm.
Shaft M7 nut, with a torque
wrench setting fixed at 8 Nm.

cm /rev
3
P1 P2 P3 r/min r/min mm mm
VNK-1-0.8-1-1-*-*-* 0.8 250 270 290 6000 1000 73.5 32.8
VNK-1-1.1-1-1-*-*-* 1.1 250 270 290 6000 1000 74 33
VNK-1-1.3-1-1-*-*-* 1.3 250 270 290 6000 1000 75 33.5
VNK-1-1.6-1-1-*-*-* 1.6 250 270 290 6000 1000 76 34
VNK-1-1.8-1-1-*-*-* 1.8 250 270 290 6000 1000 77 34.5
VNK-1-2.1-1-1-*-*-* 2.1 250 270 290 6000 1000 78 35
VNK-1-2.7-1-1-*-*-* 2.7 250 270 290 6000 800 80 36
VNK-1-3.2-1-1-*-*-* 3.2 250 270 290 5000 800 82 37
VNK-1-3.7-1-1-*-*-* 3.7 250 270 290 4500 800 84 38
VNK-1-4.2-1-1-*-*-* 4.2 250 270 290 4000 800 86 39
VNK-1-4.8-1-1-*-*-* 4.8 230 250 270 3500 600 88 40
VNK-1-5.8-1-1-*-*-* 5.8 230 250 270 3000 600 92 42
VNK-1-7-1-*-*-* 7 210 230 250 2500 600 96 44
VNK-1-8-1-1-*-*-* 8 180 200 230 2100 600 100 46
VNK-1-9.8-1-1-*-*-* 9.8 150 170 190 2100 600 104 48
11
VNK1 GEAR PUMP G1
FRONT COVERS SHAFTS
B 02
Max. Torque 20 Nm
1
1
Max. Torque 20 Nm
12
VNK1 GEAR PUMP G1
PORTS
INLET OUTLET
A a
G3/8 G3/8
3838
INLET OUTLET
A B C a b c
30 12 M6 30 12 M6
3030
INLET OUTLET
A B C a b c
30 12 M6 30 12 M6
3030R
INLET OUTLET
A a
G3/8 Ø9
380R
13
VNK2 GEAR PUMP G2
VNK2 GEAR PUMP

GROUP 2
HOW TO ORDER
VNKB 2 4 * see specifications of shafts, C Clockswise

6 flanges and ports in pages 22,
Counter
23, 24 A
8 clockwise
10
12
14
16
18
20
23
25
30
14
VNK2 GEAR PUMP G2
VNK2-*-3-3-*
M6 thread depth 13, M8 thread

depth 17. To mount the pump,
n.4 M10 screws, with a torque
wrench setting fixed at 70 ...W75
Nm. Shaft M 12x1.25 nut, with a
torque wrench setting fixed at
50 Nm.
* see specifications
of ports in page 24.

VNK-2-4-3-3-*-*-* 4 270 285 300 4000 600 92,7 44,4
VNK-2-6-3-3-*-*-* 6 270 285 300 4000 600 96 46
VNK-2-8-3-3-*-*-* 8 270 285 300 3500 500 99,3 47,7
VNK-2-10-3-3-*-*-* 10 270 285 300 3000 500 102,6 49,3
VNK-2-12-3-3-*-*-* 12 270 285 300 3000 500 105,9 51
VNK-2-14-3-3-*-*-* 14 250 265 280 4000 500 109,3 52,7
VNK-2-16-3-3-*-*-* 16 250 265 280 4000 500 112,7 54,4
VNK-2-18-3-3-*-*-* 18 250 265 280 3600 400 116 56
VNK-2-20-3-3-*-*-* 20 220 235 250 3200 400 119,3 57,7
VNK-2-23-3-3-*-*-* 23 220 235 250 3000 400 122,6 59,3
VNK-2-25 -3-3-*-*-* 25 200 215 230 3000 400 127,6 61,8
VNK-2-28 -3-3-*-*-* 28 180 190 200 2500 400 132,6 64,3
VNK-2-30-3-3-*-*-* 30 160 170 180 2500 400 135,9 66
15
VNK2 GEAR PUMP G2
VNK2-*-*-2-*-*-*
Screws tightening torque at 70

... 75 Nm

VNK-2-4-*-2-*-*-* 4 270 285 300 4000 600 92,7 44,4
VNK-2-6-*-2-*-*-* 6 270 285 300 4000 600 96 46
VNK-2-8-*-2-*-*-* 8 270 285 300 3500 500 99,3 47,7
VNK-2-10-*-2-*-*-* 10 270 285 300 3000 500 102,6 49,3
VNK-2-12-*-2-*-*-* 12 270 285 300 3000 500 105,9 51
VNK-2-14-*-2-*-*-* 14 250 265 280 4000 500 109,3 52,7
VNK-2-16-*-2-*-*-* 16 250 265 280 4000 500 112,7 54,4
VNK-2-18-*-2-*-*-* 18 250 265 280 3600 400 116 56
VNK-2-20-*-2-*-*-* 20 220 235 250 3200 400 119,3 57,7
VNK-2-23-*-2-*-*-* 23 220 235 250 3000 400 122,6 59,3
VNK-2-25 -*-2-*-*-* 25 200 215 230 3000 400 127,6 61,8
VNK-2-28 -*-2-*-*-* 28 180 190 200 2500 400 132,6 64,3
VNK-2-30-*-2-*-*-* 30 160 170 180 2500 400 135,9 66
16
VNK2 GEAR PUMP G2
VNKB2-*-*-6-*-*-*

the pump, n.4 M10 screws, with
70 ... 75 Nm.
Shaft M 12x 1.5 nut, with a
50 Nm.
*
* *

VNK-2-4-*-6-*-*-* 4 270 285 300 4000 600 92,7 44,4
VNK-2-6-*-6-*-*-* 6 270 285 300 4000 600 96 46
VNK-2-8-*-6-*-*-* 8 270 285 300 3500 500 99,3 47,7
VNK-2-10-*-6-*-*-* 10 270 285 300 3000 500 102,6 49,3
VNK-2-12-*-6-*-*-* 12 270 285 300 3000 500 105,9 51
VNK-2-14-*-6-*-*-* 14 250 265 280 4000 500 109,3 52,7
VNK-2-16-*-6-*-*-* 16 250 265 280 4000 500 112,7 54,4
VNK-2-18-*-6-*-*-* 18 250 265 280 3600 400 116 56
VNK-2-20-*-6-*-*-* 20 220 235 250 3200 400 119,3 57,7
VNK-2-23-*-6-*-*-* 23 220 235 250 3000 400 122,6 59,3
VNK-2-25 -*-6-*-*-* 25 200 215 230 3000 400 127,6 61,8
VNK-2-28 -*-6-*-*-* 28 180 190 200 2500 400 132,6 64,3
VNK-2-30-*-6-*-*-* 30 160 170 180 2500 400 135,9 66
17
VNK2 GEAR PUMP G2
VNKB2-*-*-4-*-*-*

45 ... 50 Nm.
50 Nm.
*
* *

VNK-2-4-*-4-*-*-* 4 270 285 300 4000 600 90,2 37,4
VNK-2-6-*-4-*-*-* 6 270 285 300 4000 600 93,5 38,6
VNK-2-8-*-4-*-*-* 8 270 285 300 3500 500 96,8 40,7
VNK-2-10-*-4-*-*-* 10 270 285 300 3000 500 100,1 41,2
VNK-2-12-*-4-*-*-* 12 270 285 300 3000 500 103,4 45
VNK-2-14-*-4-*-*-* 14 250 265 280 4000 500 106,8 45
VNK-2-16-*-4-*-*-* 16 250 265 280 4000 500 110,2 45
VNK-2-18-*-4-*-*-* 18 250 265 280 3600 400 113,5 45
VNK-2-20-*-4-*-*-* 20 220 235 250 3200 400 116,8 45
VNK-2-23-*-4-*-*-* 23 220 235 250 3000 400 120,1 52,6
VNK-2-25 -*-4-*-*-* 25 200 215 230 3000 400 125,1 59,3
VNK-2-28 -*-4-*-*-* 28 180 190 200 2500 400 130,1 51,8
VNK-2-30-*-4-*-*-* 30 160 170 180 2500 400 133,4 63,5
18
VNK2 GEAR PUMP G2
VNKB2-*-*-9-*-*-*

45 ...50 Nm.
50 Nm.
*
* *

VNK-2-4-*-9-*-*-C 4 4 270 285 300 4000 90,2 37,4
VNK-2-6-*-9-*-*-C 6 6 270 285 300 4000 93,5 38,6
VNK-2-8-*-9-*-*-C 8 8 270 285 300 3500 96,8 40,7
VNK-2-10-*-9-*-*-C 10 10 270 285 300 3000 100,1 41,2
VNK-2-12-*-9-*-*-C 12 12 270 285 300 3000 103,4 45
VNK-2-14-*-9-*-*-C 14 14 250 265 280 4000 106,8 45
VNK-2-16-*-9-*-*-C 16 16 250 265 280 4000 110,2 45
VNK-2-18-*-9-*-*-C 18 18 250 265 280 3600 113,5 45
VNK-2-20-*-9-*-*-C 20 20 220 235 250 3200 116,8 45
VNK-2-23-*-9-*-*-C 23 23 220 235 250 3000 120,1 52,6
VNK-2-25-*-9-*-*-C 25 25 200 215 230 3000 125,1 59,3
VNK-2-28-*-9-*-*-C 28 28 180 190 200 2500 130,1 51,8
VNK-2-30-*-9-*-*-C 30 30 160 170 180 2500 133,4 63,5
19
VNK2 GEAR PUMP G2
VNKB2-*-*-10-*-*-*

45 ...50 Nm.
70 Nm.
* *
* *

VNK-2-4-*-10-*-*-C 4 4 270 285 300 4000 90,2 37,4
VNK-2-6-*-10-*-*-C 6 6 270 285 300 4000 93,5 38,6
VNK-2-8-*-10-*-*-C 8 8 270 285 300 3500 96,8 40,7
VNK-2-10-*-10-*-*-C 10 10 270 285 300 3000 100,1 41,2
VNK-2-12-*-10-*-*-C 12 12 270 285 300 3000 103,4 45
VNK-2-14-*-10-*-*-C 14 14 250 265 280 4000 106,8 45
VNK-2-16-*-10-*-*-C 16 16 250 265 280 4000 110,2 45
VNK-2-18-*-10-*-*-C 18 18 250 265 280 3600 113,5 45
VNK-2-20-*-10-*-*-C 20 20 220 235 250 3200 116,8 45
VNK-2-23-*-10-*-*-C 23 23 220 235 250 3000 120,1 52,6
VNK-2-25-*-10-*-*-C 25 25 200 215 230 3000 125,1 59,3
VNK-2-28-*-10-*-*-C 28 28 180 190 200 2500 130,1 51,8
VNK-2-30-*-10-*-*-C 30 30 160 170 180 2500 133,4 63,5
20
VNK2 GEAR PUMP G2
VNKB2-*-*-8-*-*-*
8 thread depth 16. To mount the

pump, n.4 M10 screws, with a
70 ... 75 Nm.
* *

VNK-2-4-*-8-*-*-* 4 270 285 300 4000 600 92,7 44,4
VNK-2-6-*-8-*-*-* 6 270 285 300 4000 600 96 46
VNK-2-8-*-8-*-*-* 8 270 285 300 3500 500 99,3 47,7
VNK-2-10-*-8-*-*-* 10 270 285 300 3000 500 102,6 49,3
VNK-2-12-*-8-*-*-* 12 270 285 300 3000 500 105,9 51
VNK-2-14-*-8-*-*-* 14 250 265 280 4000 500 109,3 52,7
VNK-2-16-*-8-*-*-* 16 250 265 280 4000 500 112,7 54,4
VNK-2-18-*-8-*-*-* 18 250 265 280 3600 400 116 56
VNK-2-20-*-8-*-*-* 20 220 235 250 3200 400 119,3 57,7
VNK-2-23-*-8-*-*-* 23 220 235 250 3000 400 122,6 59,3
VNK-2-25 -*-8-*-*-* 25 200 215 230 3000 400 127,6 61,8
VNK-2-28 -*-8-*-*-* 28 180 190 200 2500 400 132,6 64,3
VNK-2-30-*-8-*-*-* 30 160 170 180 2500 400 135,9 66
21
VNK2 GEAR PUMP G2
FRONT COVERS SHAFTS
3 3
Max. Torque 200 Nm
8
10
Max. Torque 140 Nm
12
Max. Torque 150 Nm
22
VNK2 GEAR PUMP G2
FRONT COVERS SHAFTS
9 8
Max. Torque 180 Nm
10
9
Max. Torque 100 Nm
11
Max. Torque 185 Nm
23
VNK2 GEAR PUMP G2
PORTS
INLET OUTLET
PORTS CODE
A B C a b c
3030 30 13 M6 30 13 M6
4030 40 20 M8 30 13 M6
4040 40 21 M8 40 19 M8
INLET OUTLET
PORTS CODE
A a
1238 G1/2 G3/8
3412 G3/4 G1/2
1034 G1 G3/4
INLET OUTLET
PORTS CODE
A B C a b c
4035 40 20 M6 35 15 M6
24
VNK3 GEAR PUMP G3
VNK3 GEAR PUMP

GROUP 3
HOW TO ORDER
VNKB 3 25 * see specifications of shafts, C Clockswise

28 flanges and ports in pages 28,
Counter
29. A
30 clockwise
32
36
38
40
44
50
52
55
63
71
80
90
100
25
VNK3 GEAR PUMP G3
VNK3-*-2-5-*
M10 thread depth 18, To mount

47±3 Nm.
80 Nm.

Type Speed Speed M L B
cm /rev
3
VNKB3-25-2-5-*-*-* 25 260 290 300 3000 500 123 59,3 118
VNKB3-28-2-5-*-*-* 28 260 290 300 3000 500 126 60,8 118
VNKB3-30-2-5-*-*-* 30 250 280 300 3000 500 129 62 118
VNKB3-32-2-5-*-*-* 32 250 280 300 3000 500 131 63,3 118
VNKB3-36-2-5-*-*-* 36 250 280 300 2750 400 135 65,3 118
VNKB3-38-2-5-*-*-* 38 250 280 300 2750 400 137 66,3 118
VNKB3-40-2-5-*-*-* 40 250 280 300 2750 400 139 67,3 118
VNKB3-44-2-5-*-*-* 44 250 280 300 2750 400 144 69,5 118
VNKB3-50-2-5-*-*-* 50 220 240 260 3000 500 156 77 146
VNKB3-52-2-5-*-*-* 52 220 240 260 3000 500 158 78 146
VNKB3-55-2-5-*-*-* 55 220 240 260 2750 400 160 79 146
VNKB3-63-2-5-*-*-* 63 200 230 250 2750 400 168 83 146
VNKB3-71-2-5-*-*-* 71 180 200 220 2500 400 175 86 146
VNKB3-80-2-5-*-*-* 80 180 200 220 2500 400 189 96 146
VNKB3-90-2-5-*-*-* 90 180 200 220 2500 400 195 99 146
VNKB3-100-2-5-*-*-* 100 160 180 200 2500 400 201 102 146
26
VNK3 GEAR PUMP G3
VNK3-*-*-7-*
To mount the pump, n.8 M10

screws, with a torque wrench
setting fixed at 47±3 Nm.

Type Speed Speed M L B
cm /rev
3
VNKB3-25-*-7-*-*-* 25 260 290 300 3000 500 123 59,3 118
VNKB3-28-*-7-*-*-* 28 260 290 300 3000 500 126 60,8 118
VNKB3-30-*-7-*-*-* 30 250 280 300 3000 500 129 62 118
VNKB3-32-*-7-*-*-* 32 250 280 300 3000 500 131 63,3 118
VNKB3-36-*-7-*-*-* 36 250 280 300 2750 400 135 65,3 118
VNKB3-38-*-7-*-*-* 38 250 280 300 2750 400 137 66,3 118
VNKB3-40-*-7-*-*-* 40 250 280 300 2750 400 139 67,3 118
VNKB3-44-*-7-*-*-* 44 250 280 300 2750 400 144 69,5 118
VNKB3-50-*-7-*-*-* 50 220 240 260 3000 500 156 77 146
VNKB3-52-*-7-*-*-* 52 220 240 260 3000 500 158 78 146
VNKB3-55-*-7-*-*-* 55 220 240 260 2750 400 160 79 146
VNKB3-63-*-7-*-*-* 63 200 230 250 2750 400 168 83 146
VNKB3-71-*-7-*-*-* 71 180 200 220 2500 400 175 86 146
VNKB3-80-*-7-*-*-* 80 180 200 220 2500 400 189 96 146
VNKB3-90-*-7-*-*-* 90 180 200 220 2500 400 195 99 146
VNKB3-100-*-7-*-*-* 100 160 180 200 2500 400 201 102 146
27
VNK3 GEAR PUMP G3
FRONT COVERS SHAFTS
5 2
Max. Torque 300 Nm
7
14
Max. Torque 400 Nm
15
Max. Torque 500 Nm
28
VNK3 GEAR PUMP G3
PORTS
INLET OUTLET
PORTS CODE
A a
10 34 G1 G3/4
114 10 G1 1/4 G1
112 114 G1 1/2 G1 1/4
INLET OUTLET
PORTS CODE
A B C a b c
51 40 51 25 M10 40 18 M8
62 51 62 33 M10 51 27 M10
62 62 62 33 M10 62 33 M10
INLET OUTLET
PORTS CODE
A B C D a b c d
52 47 52.4 26.2 3/8-16UNC 27 47.6 22.2 3/8-16UNC 19
58 52 58.7 30.2 7/16-14UNC 33 52.4 26.2 3/8-16UNC 27
29
VNK MULTIPLE GEAR PUMP
MULTIPLE PUMPS
The VNKBM pumps can be easily transformed in multiple units. All drive shafts
are pre-arranged and have a splined end according DIN 5480. The first unit must
always be the same size or bigger than following units. The features and perfor-
mances are the same of the corresponding single units: only in the case of simul-
taneous operating you have to verify that the inlet torque is lower than the max.
transmissible by the drive shaft. Finally to assembly the multiple pump you need
to order bolts of the right lenght.
Standard Version
S H
J W
S- two inlet and two outlet

(separated type)
H- two inlet and two outlet
(common type)
J- one inlet and two outlet
W- one inlet and three outlet
R
R- two inlet and three outlet
30
VNKBMD - DRIVER PUMP
HOW TO ORDER
Multiple Standard
Group Size Shaft * Flange * Inlet port * Outlet port * Rotation
pump Version
VNKBMD 3 25 * see specifications of shafts, C Clockswise S

2 4 30 flanges and ports in pages 42, H
Counter
43, 44, 45, 46. A
1 1.1 6 33 clockwise J
1.3 8 39 W
1.6 10 46 R
1.8 12 50
2.1 14 55
2.7 16 63
3.2 18 70
3.7 20 80
4.2 23 90
5 25
5.8 30
7
8
31
VNKBMD GROUP 1
VNK1/1-S

Type Speed Speed B
cm3/rev P1 P2 P3 r/min r/min mm
VNKBMD-1-1.1-1-1-*-*-* 1.1 250 270 290 6000 1000 18,5
VNKBMD-1-1.3-1-1-*-*-* 1.3 250 270 290 6000 1000 19
VNKBMD-1-1.6-1-1-*-*-* 1.6 250 270 290 6000 1000 19,5
VNKBMD-1-1.8-1-1-*-*-* 1.8 250 270 290 6000 1000 20
VNKBMD-1-2.1-1-1-*-*-* 2.1 250 270 290 6000 1000 21
VNKBMD-1-2.7-1-1-*-*-* 2.7 250 270 290 6000 1000 22
VNKBMD-1-3.2-1-1-*-*-* 3.2 250 270 290 6000 800 23
VNKBMD-1-3.7-1-1-*-*-* 3.7 250 270 290 5000 800 24
VNKBMD-1-4.2-1-1-*-*-* 4.2 250 270 290 4500 800 25
VNKBMD-1-4.8-1-1-*-*-* 4.8 230 250 270 4000 800 26
VNKBMD-1-5.8-1-1-*-*-* 5.8 230 250 270 3500 600 28
VNKBMD-1-7-1-*-*-* 7 210 230 250 3000 600 30
VNKBMD-1-8-1-1-*-*-* 8 180 200 230 2500 600 32
32
VNKBMD GROUP 2
VNK2/2/2-S
VNK2/1-S
33

Type Speed Speed A
cm /rev
3
P1 P2 P3 r/min r/min mm
VNKBMD2-4-*-*-*-*-* 4 270 285 300 4000 600 25,3
VNKBMD2-6-*-*-*-*-* 6 270 285 300 4000 600 27
VNKBMD2-8-*-*-*-*-* 8 270 285 300 3500 500 28,6
VNKBMD2-10-*-*-*-*-* 10 270 285 300 3000 500 30,3
VNKBMD2-12-*-*-*-*-* 12 270 285 300 3000 500 32
VNKBMD2-14-*-*-*-*-* 14 250 265 280 4000 500 33,6
VNKBMD2-16-*-*-*-*-* 16 250 265 280 4000 500 35,3
VNKBMD2-18-*-*-*-*-* 18 250 265 280 3600 400 37
VNKBMD2-20-*-*-*-*-* 20 220 235 250 3200 400 38,6
VNKBMD2-2*-*-3-*-*-* 23 220 235 250 3000 400 40,3
VNKBMD2-25 -*-*-*-*-* 25 200 215 230 3000 400 42,8
VNKBMD2-28 -*-*-*-*-* 28 180 190 200 2500 400 45,3
VNKBMD2-30-*-*-*-*-* 30 160 170 180 2500 400 47
34
VNKBMD GROUP 3
VNK3/3-S
VNK3/2-S
VNK3/1-S
35

Type Speed Speed A
cm /rev
3
VNKBMD3-25-*-*-*-*-* 25 260 290 300 3000 500 43
VNKBMD3-30-*-*-*-*-* 30 250 280 300 3000 500 46
VNKBMD3-33-*-*-*-*-* 33 250 280 300 3000 500 46
VNKBMD3-39-*-*-*-*-* 39 250 280 300 2750 400 49,5
VNKBMD3-46-*-*-*-*-* 46 250 280 300 2750 400 52,5
VNKBMD3-50-*-*-*-*-* 50 220 240 260 3000 500 54,5
VNKBMD3-55-*-*-*-*-* 55 220 240 260 2750 400 56,5
VNKBMD3-63-*-*-*-*-* 63 200 230 250 2750 400 60,7
VNKBMD3-71-*-*-*-*-* 71 180 200 220 2500 400 64
VNKBMD3-80-*-*-*-*-* 80 180 200 220 2500 400 71
VNKBMD3-90-*-*-*-*-* 90 180 200 220 2500 400 80
36
VNKBMI - INTERMEDIATE PUMP
HOW TO ORDER
Multiple Standard
Group Size Inlet port * Outlet port * Rotation
pump Version
VNKBMI 3 25 C Clockswise S
2 4 30 Counter H
A
1.3 8 39 W
1.6 10 46 R
1.8 12 50
2.1 14 55 * see specifications of ports in
pages 42, 43, 44, 45, 46.
2.7 16 63
3.2 18 70
3.7 20 80
4.2 23 90
5 25
5.8 30
7
8
37

Type Speed Speed B
cm /rev
3
VNKBMI-1-1.1-1-1-*-*-* 1.1 250 270 290 6000 1000 18,5
VNKBMI-1-1.3-1-1-*-*-* 1.3 250 270 290 6000 1000 19
VNKBMI-1-1.6-1-1-*-*-* 1.6 250 270 290 6000 1000 19,5
VNKBMI-1-1.8-1-1-*-*-* 1.8 250 270 290 6000 1000 20
VNKBMI-1-2.1-1-1-*-*-* 2.1 250 270 290 6000 1000 21
VNKBMI-1-2.7-1-1-*-*-* 2.7 250 270 290 6000 1000 22
VNKBMI-1-3.2-1-1-*-*-* 3.2 250 270 290 6000 800 23
VNKBMI-1-3.7-1-1-*-*-* 3.7 250 270 290 5000 800 24
VNKBMI-1-4.2-1-1-*-*-* 4.2 250 270 290 4500 800 25
VNKBMI-1-4.8-1-1-*-*-* 4.8 230 250 270 4000 800 26
VNKBMI-1-5.8-1-1-*-*-* 5.8 230 250 270 3500 600 28
VNKBMI-1-7-1-*-*-* 7 210 230 250 3000 600 30
VNKBMI-1-8-1-1-*-*-* 8 180 200 230 2500 600 32

Type Speed Speed A
VNKBMI2-4-*-*-*-*-* 4 270 285 300 4000 600 25,3
VNKBMI2-6-*-*-*-*-* 6 270 285 300 4000 600 27
VNKBMI2-8-*-*-*-*-* 8 270 285 300 3500 500 28,6
VNKBMI2-10-*-*-*-*-* 10 270 285 300 3000 500 30,3
VNKBMI2-12-*-*-*-*-* 12 270 285 300 3000 500 32
VNKBMI2-14-*-*-*-*-* 14 250 265 280 4000 500 33,6
VNKBMI2-16-*-*-*-*-* 16 250 265 280 4000 500 35,3
VNKBMI2-18-*-*-*-*-* 18 250 265 280 3600 400 37
VNKBMI2-20-*-*-*-*-* 20 220 235 250 3200 400 38,6
VNKBMI2-2*-*-3-*-*-* 23 220 235 250 3000 400 40,3
VNKBMI2-25 -*-*-*-*-* 25 200 215 230 3000 400 42,8
VNKBMI2-28 -*-*-*-*-* 28 180 190 200 2500 400 45,3
VNKBMI2-30-*-*-*-*-* 30 160 170 180 2500 400 47

Type Speed Speed A
VNKBMI3-25-*-*-*-*-* 25 260 290 300 3000 500 43
VNKBMI3-30-*-*-*-*-* 30 250 280 300 3000 500 46
VNKBMI3-33-*-*-*-*-* 33 250 280 300 3000 500 46
VNKBMI3-39-*-*-*-*-* 39 250 280 300 2750 400 49,5
VNKBMI3-46-*-*-*-*-* 46 250 280 300 2750 400 52,5
VNKBMI3-50-*-*-*-*-* 50 220 240 260 3000 500 54,5
VNKBMI3-55-*-*-*-*-* 55 220 240 260 2750 400 56,5
VNKBMI3-63-*-*-*-*-* 63 200 230 250 2750 400 60,7
VNKBMI3-71-*-*-*-*-* 71 180 200 220 2500 400 64
VNKBMI3-80-*-*-*-*-* 80 180 200 220 2500 400 71
VNKBMI3-90-*-*-*-*-* 90 180 200 220 2500 400 80
38
VNKBMF - FINAL PUMP
HOW TO ORDER
Multiple Standard
Group Size Inlet port * Outlet port * Rotation
pump Version
VNKBMF 3 25 C Clockswise S
2 4 30 Counter H
A
1.3 8 39 W
1.6 10 46 R
1.8 12 50
2.1 14 55 * see specifications of ports in
pages 45, 46.
2.7 16 63
3.2 18 70
3.7 20 80
4.2 23 90
5 25
5.8 30
7
8
39

Type Speed Speed B
cm /rev
3
VNKBMF-1-1.1-1-1-*-*-* 1.1 250 270 290 6000 1000 18,5
VNKBMF-1-1.3-1-1-*-*-* 1.3 250 270 290 6000 1000 19
VNKBMF-1-1.6-1-1-*-*-* 1.6 250 270 290 6000 1000 19,5
VNKBMF-1-1.8-1-1-*-*-* 1.8 250 270 290 6000 1000 20
VNKBMF-1-2.1-1-1-*-*-* 2.1 250 270 290 6000 1000 21
VNKBMF-1-2.7-1-1-*-*-* 2.7 250 270 290 6000 1000 22
VNKBMF-1-3.2-1-1-*-*-* 3.2 250 270 290 6000 800 23
VNKBMF-1-3.7-1-1-*-*-* 3.7 250 270 290 5000 800 24
VNKBMF-1-4.2-1-1-*-*-* 4.2 250 270 290 4500 800 25
VNKBMF-1-4.8-1-1-*-*-* 4.8 230 250 270 4000 800 26
VNKBMF-1-5.8-1-1-*-*-* 5.8 230 250 270 3500 600 28
VNKBMF-1-7-1-*-*-* 7 210 230 250 3000 600 30
VNKBMF-1-8-1-1-*-*-* 8 180 200 230 2500 600 32

Type Speed Speed A
VNKBMF2-4-*-*-*-*-* 4 270 285 300 4000 600 25,3
VNKBMF2-6-*-*-*-*-* 6 270 285 300 4000 600 27
VNKBMF2-8-*-*-*-*-* 8 270 285 300 3500 500 28,6
VNKBMF2-10-*-*-*-*-* 10 270 285 300 3000 500 30,3
VNKBMF2-12-*-*-*-*-* 12 270 285 300 3000 500 32
VNKBMF2-14-*-*-*-*-* 14 250 265 280 4000 500 33,6
VNKBMF2-16-*-*-*-*-* 16 250 265 280 4000 500 35,3
VNKBMF2-18-*-*-*-*-* 18 250 265 280 3600 400 37
VNKBMF2-20-*-*-*-*-* 20 220 235 250 3200 400 38,6
VNKBMF2-2*-*-3-*-*-* 23 220 235 250 3000 400 40,3
VNKBMF2-25 -*-*-*-*-* 25 200 215 230 3000 400 42,8
VNKBMF2-28 -*-*-*-*-* 28 180 190 200 2500 400 45,3
VNKBMF2-30-*-*-*-*-* 30 160 170 180 2500 400 47

Type Speed Speed A
VNKBMF3-25-*-*-*-*-* 25 260 290 300 3000 500 43
VNKBMF3-30-*-*-*-*-* 30 250 280 300 3000 500 45
VNKBMF3-33-*-*-*-*-* 33 250 280 300 3000 500 46
VNKBMF3-39-*-*-*-*-* 39 250 280 300 2750 400 49,5
VNKBMF3-46-*-*-*-*-* 46 250 280 300 2750 400 52,5
VNKBMF3-50-*-*-*-*-* 50 220 240 260 3000 500 54,5
VNKBMF3-55-*-*-*-*-* 55 220 240 260 2750 400 56,5
VNKBMF3-63-*-*-*-*-* 63 200 230 250 2750 400 60,7
VNKBMF3-71-*-*-*-*-* 71 180 200 220 2500 400 64
VNKBMF3-80-*-*-*-*-* 80 180 200 220 2500 400 71
VNKBMF3-90-*-*-*-*-* 90 180 200 220 2500 400 80
40
KIT UNION
VNKBMK11 MULTIPLE PUMP KIT 1+1
41
FRONT COVERS SHAFTS
1 1
Max. Torque 20 Nm
3
7
8
12
Max. Torque 150 Nm
42
FRONT COVERS SHAFTS
4 9
Max. Torque 135 Nm
9
8
Max. Torque 180 Nm
10
11
Max. Torque 185 Nm
43
FRONT COVERS SHAFTS
5 2
Max. Torque 300 Nm
7
14
Max. Torque 400 Nm
15
Max. Torque 500 Nm
44
PORTS
INLET OUTLET
A a
G3/8 G3/8
3838
INLET OUTLET
A B C a b c
30 12 M6 30 12 M6
3030
INLET OUTLET
A B C a b c
30 12 M6 30 12 M6
3030R
45
PORTS
INLET OUTLET
PORTS CODE
A B C a b c
3030 30 13 M6 30 13 M6
4030 40 20 M8 30 13 M6
4040 40 21 M8 40 19 M8
INLET OUTLET
PORTS CODE
A a
1238 G1/2 G3/8
3412 G3/4 G1/2
1034 G1 G3/4
INLET OUTLET
PORTS CODE
A a
10 34 G1 G3/4
114 10 G1 1/4 G1
112 114 G1 1/2 G1 1/4
INLET OUTLET
PORTS CODE
A B C a b c
4035 40 20 M6 35 15 M6
INLET OUTLET
PORTS CODE
A B C a b c
51 40 51 25 M10 40 18 M8
62 51 62 33 M10 51 27 M10
62 62 62 33 M10 62 33 M10
46
ASSEMBLED PUMP
Multiple Standard
Group Size Shaft * Flange * Inlet port * Outlet port * Rotation
pump Version
VNKBM 3 25 * see specifications of shafts, C Clockswise S

2 4 30 flanges and ports in pages 42, H
Counter
43, 44, 45, 46. A
1.3 8 39 W
1.6 10 46 R
1.8 12 50 EXAMPLE
2.1 14 55
Multiple pump with driver pump G3 50cc cover flange
2.7 16 63
cylindrical shaft Ø22, FLANGED PORTS, intermedia-
3.2 18 70
te pump G2 16cc flanged port and final pump G1 4cc
3.7 20 80
4.2 23 90
with thread ports, clock wise rotation two inlet and two
5 25 outlet.
5.8 30
VNKBM-3-2-1-50-16-4-14-7-51-40-40-30-38-38-C-S
7
8
47
www.vinckehydraulics.com [email protected]

Vincke Gear Pumps Cat

Uploaded by

Copyright:

Available Formats

Vincke Gear Pumps Cat

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vincke Gear Pumps Cat

Uploaded by

Copyright:

Available Formats

VINCKE HYDRAULICS

Peak up to 30Mpa max. 3 sec.

• By far largest number of premature failures of gear pumps is due

Standard P<2000PSI(14MPa) 2000PSI(14MPa)<P<3050PSI(21MPa) P>3050PSI(21MPa)

PRESSURE DEFINITION INLET PRESSURE

P3= peak max. pressure Under standard working con-

Max. 20 sec. Max. 2 sec.

ROTATION DIRECTION INLET AND DELIVERY LINES

DESIGN CALCULATIONS FOR PUMP

Q= flow rote (l/m)

your Hydraulic Brand

VNK0 GEAR PUMP

End cover: G1 / 4 thread depth

VNKB 0,5 0.19 01 B 38 OR C Clockswise

your Hydraulic Brand

Max. Min. Dimensions

your Hydraulic Brand

VNK1 GEAR PUMP

VNKB 1 0.8 * see specifications of shafts, C Clockswise

your Hydraulic Brand

End cover: G3/8 thread depth

Max. Min. Dimensions

your Hydraulic Brand

M6 threads depth 12. To mount

Max. Min. Dimensions

your Hydraulic Brand

M6 thread depth 12. To mount

Max. Min. Dimensions

your Hydraulic Brand

FRONT COVERS SHAFTS

your Hydraulic Brand

your Hydraulic Brand

VNK2 GEAR PUMP

VNKB 2 4 * see specifications of shafts, C Clockswise

your Hydraulic Brand

M6 thread depth 13, M8 thread

Max. Min. Dimensions

your Hydraulic Brand

Screws tightening torque at 70

Max. Min. Dimensions

your Hydraulic Brand

M6 thread depth 13. To mount

Max. Min. Dimensions

your Hydraulic Brand

M6 thread depth 13. To mount

Max. Min. Dimensions

your Hydraulic Brand

M6 thread depth 13. To mount

Max. Min. Dimensions

your Hydraulic Brand

M6 thread depth 13. To mount

Max. Min. Dimensions

your Hydraulic Brand

8 thread depth 16. To mount the

Max. Min. Dimensions

your Hydraulic Brand

FRONT COVERS SHAFTS

Max. Torque 200 Nm

Max. Torque 140 Nm