Weight - Balance - Spreadsheet - Guide BMAA

This is a brief step-by-step screen shot guide to using
the new BMAA weight and balance spreadsheet

(AW/028 Issue 9).
If you have any questions

please contact the BMAA Technical Office
01869 336006
The Spreadsheet should be downloaded from the BMAA
website
www.bmaa.org
Click BMAA Technical Office > BMAA Technical Document

> BMAA Forms
There are two versions:
.xls works on older versions of MS Excel (2003 and earlier)
.xlsx works on later MS Excel, Apple and Android devices
Click or tap on the desired version, then save and open

If you get a warning message, ensure you enable editing
Part 1: Actual Empty Weight & Inventory
Complete the aircraft &

owner details. This
should automatically copy
across to other pages in
the spreadsheet
Click on the text in order

to select whether the
aircraft type; weight-shift
or 3-axis. Enter the Data
Sheet reference and units
Inventory, Wheel Weights & Empty CG
Enter all inventory items

in the box provided, these
are items that are in
addition to the basic
airframe. If unsure just
add the item to the list.
Some examples are
shown.
Also enter the wheel

weights and datums (if
applicable)
Subsequent changes can be accomodated after the wheel

weights have been entered, this allows for tracking and
updating of the weight report between reweighs.
Finally sign and

date the form
Part 2: Balance
This section is
used to check the
balance of an
aircraft. It is
accessed using
the Balance tabs
at the foot of the
Spreadsheet
Seat types: Fixed, Adjustable & Weight Dependent
You have to physically click

(or tap) on the text in order
to get the drop down menu
to select the seat type for
the pilot.
Once selected the Min, Max

& Datum fields will become
active
Passenger: Repeat the last step in order to activate the
passenger cell, again you have the option to choose fixed,
adjustable of weight dependent positions.
If applicable to the type activate the Maximum Occupant Load cell by

clicking on it. Note this is used when the maximum cockpit weight is less
than the maximum combined seat & baggage limits. For example the
C42 can have 120kg in either seat, but the overall cockpit limit is only
172kg (not 240kg!). The aircraft data sheet should provide the data.
If the type is not limited, like the Skyranger, then there is no need to
activate this function in the Spreadsheet, you can leave it greyed out.
Fuel:
Input the fuel capacity,

additional tanks can be
accounted for by
clicking and activitating
the cells - this can be
used for slipper and
header tanks.
Miscellaneous Items: This is mainly be used for baggage

capacity, again you need to activate the function before
being able to use it
Weight & CG limitations:
Enter the Max All Up

Weight or MTOW and
the corresponding fore
and aft CG limits
Weight Dependent CG Limitations:
A limited number of types, such as the C42, have variable

CG limits depending upon the MAUW/MTOW. The
spreadsheet can accomodate such scenarios.
As previous first you need to activate the function by

clicking or tapping on the section. Then additional CG
limits become available. Enter the values with reference
to the aircraft data sheet.
Be sure to match the correct CG limits to the

corresponding MAUW limit. For example in the case of
the C42:
MAUW Aft CG Limit Forward CG Limit

472.5kg 560mm 366mm
≤450kg 560mm 350mm
Finally click on the Balance 2 of 2 tab to see the results

The spreadsheet will
Part 3: Result
indicate (Y or N) whether
the aircraft remains within
limitations in all legal
loading condition.
The spreadsheet provides a

breakdown of the most
forward and most aft loading
scenarios.
In this case the result is

inside by 13.32%
In this case the results are

outside by some margin.
Naturally this would warrant

investigation to determine
the cause.
Variable CG Limits:
With variable CG limitations,

the spreadsheet will return
results for both MAUW
figures specified, this case
472.5kg (heavy condition)
and 450kg (light condition)
**Don’t forget to sign and date the report**

Part 4: Fuel Trade-off Placard
If the aircraft can be loaded over the MAUW, then a Fuel
Trade-off Placard must be produced.
Type the A/C reg into the top

of the table. Then fill out the
other red cells with the
appropriate figures.
Finally decide on the weight

divisions required (resolution)
and the table will be
produced.
Change the size of the table

by altering the Cockpit Load
Increment number. Lower
value increases divisions,
higher number gives fewer.
Generally 5 works well, for

an aircraft with large tanks
(like CT range) it would be
best to use a figure of 10.
PLACARDING & LOGBOOK:

Do not forget to make a logbook entry with the wheel weights
and empty CG location. All placards must be updated. Finally
the report (all pages) must be submitted to the
BMAA Tech Office for checking and final approval.

Weight - Balance - Spreadsheet - Guide BMAA

Uploaded by

Copyright:

Available Formats

Weight - Balance - Spreadsheet - Guide BMAA

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Weight - Balance - Spreadsheet - Guide BMAA

Uploaded by

Copyright:

Available Formats

This is a brief step-by-step screen shot guide to using

the new BMAA weight and balance spreadsheet

If you have any questions

Click BMAA Technical Office > BMAA Technical Document

Click or tap on the desired version, then save and open

Part 1: Actual Empty Weight & Inventory

Complete the aircraft &

Click on the text in order

Enter all inventory items

Also enter the wheel

Subsequent changes can be accomodated after the wheel

Finally sign and

Seat types: Fixed, Adjustable & Weight Dependent

You have to physically click

Once selected the Min, Max

If applicable to the type activate the Maximum Occupant Load cell by

Input the fuel capacity,

Miscellaneous Items: This is mainly be used for baggage

Enter the Max All Up

Weight Dependent CG Limitations:

A limited number of types, such as the C42, have variable

As previous first you need to activate the function by

Be sure to match the correct CG limits to the

MAUW Aft CG Limit Forward CG Limit

Finally click on the Balance 2 of 2 tab to see the results

The spreadsheet provides a

In this case the result is

In this case the results are

Naturally this would warrant

With variable CG limitations,

**Don’t forget to sign and date the report**

Type the A/C reg into the top

Finally decide on the weight

Change the size of the table

Generally 5 works well, for

PLACARDING & LOGBOOK:

You might also like

Don’t forget to sign and date the report