Super Sequencer With Margining Control and Temperature Monitoring ADM1062

Super Sequencer with Margining Control and Temperature Monitoring ADM1062
FEATURES
Complete supervisory and sequencing solution for up to 10 supplies 10 supply fault detectors enable supervision of supplies to <0.5% accuracy at all voltages at 25C <1.0% accuracy across all voltages and temperatures 5 selectable input attenuators allow supervision of supplies to 14.4 V on VH 6 V on VP1 to VP4 (VPx) 5 dual-function inputs, VX1 to VX5 (VXx) High impedance input to supply fault detector with thresholds between 0.573 V and 1.375 V General-purpose logic input 10 programmable driver outputs, PDO1 to PDO10 (PDOx) Open-collector with external pull-up Push/pull output, driven to VDDCAP or VPx Open collector with weak pull-up to VDDCAP or VPx Internally charge-pumped high drive for use with external N-FET (PDO1 to PDO6 only) Sequencing engine (SE) implements state machine control of PDO outputs State changes conditional on input events Enables complex control of boards Power-up and power-down sequence control Fault event handling Interrupt generation on warnings Watchdog function can be integrated in SE Program software control of sequencing through SMBus Complete voltage margining solution for 6 voltage rails 6 voltage output, 8-bit DACs (0.300 V to 1.551 V) allow voltage adjustment via dc-to-dc converter trim/feedback node 12-bit ADC for readback of all supervised voltages Internal and external temperature sensors Reference input (REFIN) has 2 input options Driven directly from 2.048 V (0.25%) REFOUT pin More accurate external reference for improved ADC performance Device powered by the highest of VPx, VH for improved redundancy User EEPROM: 256 bytes Industry-standard 2-wire bus interface (SMBus) Guaranteed PDO low with VH, VPx = 1.2 V Available in 40-lead, 6 mm 6 mm LFCSP and 48-lead, 7 mm 7 mm TQFP packages For more information about the ADM1062 register map, refer to the AN-698 Application Note at www.analog.com.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
DP
FUNCTIONAL BLOCK DIAGRAM

DN REFIN REFOUT REFGND SDA SCL A1 A0
ADM1062
TEMP SENSOR INTERNAL DIODE VREF SMBus INTERFACE
MUX
12-BIT SAR ADC
EEPROM
CLOSED-LOOP MARGINING SYSTEM VX1 VX2 VX3 VX4 VX5 DUALFUNCTION INPUTS (LOGIC INPUTS OR SFDs) SEQUENCING ENGINE VP1 VP2 VP3 VP4 VH AGND VOUT DAC VOUT DAC VOUT DAC VOUT DAC VOUT DAC VOUT DAC VDD ARBITRATOR PROGRAMMABLE RESET GENERATORS (SFDs) CONFIGURABLE OUTPUT DRIVERS (LV CAPABLE OF DRIVING LOGIC SIGNALS) PDO7 PDO8 PDO9 PDO10 PDOGND VDDCAP
04433-001
CONFIGURABLE OUTPUT DRIVERS (HV CAPABLE OF DRIVING GATES OF N-FET)
PDO1 PDO2 PDO3 PDO4 PDO5 PDO6
DAC1 DAC2 DAC3 DAC4 DAC5 DAC6
VCCP GND
Figure 1.
APPLICATIONS
Central office systems Servers/routers Multivoltage system line cards DSP/FPGA supply sequencing In-circuit testing of margined supplies
GENERAL DESCRIPTION
The ADM1062 Super Sequencer is a configurable supervisory/ sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple-supply systems. In addition to these functions, the ADM1062 integrates a 12-bit ADC and six 8-bit voltage output DACs. These circuits can be used to implement a closed-loop margining system that enables supply adjustment by altering either the feedback node or the reference of a dc-to-dc converter using the DAC outputs.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 20052008 Analog Devices, Inc. All rights reserved.
ADM1062 TABLE OF CONTENTS

Features .............................................................................................. 1 Functional Block Diagram .............................................................. 1 Applications....................................................................................... 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Detailed Block Diagram .................................................................. 3 Specifications..................................................................................... 4 Absolute Maximum Ratings............................................................ 7 Thermal Resistance ...................................................................... 7 ESD Caution.................................................................................. 7 Pin Configurations and Function Descriptions ........................... 8 Typical Performance Characteristics ........................................... 10 Powering the ADM1062 ................................................................ 13 Inputs................................................................................................ 14 Supply Supervision..................................................................... 14 Programming the Supply Fault Detectors............................... 14 Input Comparator Hysteresis.................................................... 14 Input Glitch Filtering ................................................................. 15 Supply Supervision with VXx Inputs....................................... 15 VXx Pins as Digital Inputs ........................................................ 15 Outputs ............................................................................................ 16 Supply Sequencing Through Configurable Output Drivers. 16 Default Output Configuration.................................................. 16 Sequencing Engine ......................................................................... 17 Overview...................................................................................... 17 Warnings...................................................................................... 17 SMBus Jump (Unconditional Jump)........................................ 17 Sequencing Engine Application Example ............................... 18 Fault and Status Reporting........................................................ 19 Voltage Readback............................................................................ 20 Supply Supervision with the ADC ........................................... 20 Supply Margining ........................................................................... 21 Overview ..................................................................................... 21 Open-Loop Supply Margining ................................................. 21 Closed-Loop Supply Margining ............................................... 21 Writing to the DACs .................................................................. 22 Choosing the Size of the Attenuation Resistor....................... 22 DAC Limiting and Other Safety Features ............................... 22 Temperature Measurement System.............................................. 23 Remote Temperature Measurement ........................................ 23 Applications Diagram .................................................................... 25 Communicating with the ADM1062........................................... 26 Configuration Download at Power-Up................................... 26 Updating the Configuration ..................................................... 26 Updating the Sequencing Engine............................................. 27 Internal Registers........................................................................ 27 EEPROM ..................................................................................... 27 Serial Bus Interface..................................................................... 27 SMBus Protocols for RAM and EEPROM.............................. 30 Write Operations ........................................................................ 30 Read Operations......................................................................... 31 Outline Dimensions ....................................................................... 33 Ordering Guide .......................................................................... 34
REVISION HISTORY
5/08Rev. A to Rev. B Changes to Table 1............................................................................ 4 Changes to Powering the ADM1062 Section ............................. 13 Changes to Table 5.......................................................................... 14 Changes to Sequence Detector Section ....................................... 18 Changes to Temperature Measurement System Section ........... 23 Changes to Table 11........................................................................ 24 Changes to Configuration Download at Power-Up Section..... 26 Changes to Table 12........................................................................ 27 Changes to Figure 49 and Error Correction Section ................. 32 Changes to Ordering Guide .......................................................... 34 12/06Rev. 0 to Rev. A Updated Format..................................................................Universal Changes to Features.......................................................................... 1 Changes to Figure 2...........................................................................3 Changes to Table 1.............................................................................4 Changes to Table 2.............................................................................7 Changes to Absolute Maximum Ratings Section..........................9 Changes to Programming the Supply Fault Detectors Section... 14 Changes to Table 6.......................................................................... 14 Changes to Outputs Section.......................................................... 16 Changes to Fault Reporting Section ............................................ 20 Changes to Table 9.......................................................................... 21 Changes to Identifying the ADM1062 on the SMBus Section .................................................................... 28 Changes to Figure 39 and Figure 30............................................. 30 4/05Revision 0: Initial Version
Rev. B | Page 2 of 36
ADM1062
Supply margining can be performed with a minimum of external components. The margining loop can be used for in-circuit testing of a board during production (for example, to verify board functionality at 5% of nominal supplies), or it can be used dynamically to accurately control the output voltage of a dc-to-dc converter. The device also provides up to 10 programmable inputs for monitoring undervoltage faults, overvoltage faults, or out-ofwindow faults on up to 10 supplies. In addition, 10 programmable outputs can be used as logic enables. Six of these programmable outputs can also provide up to a 12 V output for driving the gate of an N-FET that can be placed in the path of a supply. Temperature measurement is possible with the ADM1062. The device contains one internal temperature sensor and a differential input for a remote thermal diode. Both are measured by the 12-bit ADC. The logical core of the device is a sequencing engine. This statemachine-based construction provides up to 63 different states. This design enables very flexible sequencing of the outputs, based on the condition of the inputs. The ADM1062 is controlled via configuration data that can be programmed into an EEPROM. The entire configuration can be programmed using an intuitive GUI-based software package provided by Analog Devices, Inc.
DETAILED BLOCK DIAGRAM

REFIN DP DN REFOUT REFGND SDA SCL A1 A0
TEMP SENSOR
INTERNAL DIODE
ADM1062
VREF
SMBus INTERFACE
12-BIT SAR ADC
DEVICE CONTROLLER
OSC EEPROM
GPI SIGNAL CONDITIONING VX1 VX2 VX3 VX4 GPI SIGNAL CONDITIONING VX5 SFD SELECTABLE ATTENUATOR SEQUENCING ENGINE SFD
CONFIGURABLE OUTPUT DRIVER (HV)
PDO1 PDO2 PDO3 PDO4 PDO5
CONFIGURABLE OUTPUT DRIVER (HV)
PDO6
VP1 VP2 VP3 VP4 VH
SFD
CONFIGURABLE OUTPUT DRIVER (LV)
PDO7 PDO8 PDO9
SELECTABLE ATTENUATOR
SFD
CONFIGURABLE OUTPUT DRIVER (LV)
PDO10 PDOGND
AGND VDDCAP VDD ARBITRATOR REG 5.25V CHARGE PUMP VOUT DAC VOUT DAC
GND
VCCP
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
Figure 2.
04433-002
ADM1062 SPECIFICATIONS
VH = 3.0 V to 14.4 V 1 , VPx = 3.0 V to 6.0 V1, TA = 40C to +85C, unless otherwise noted. Table 1.
Parameter POWER SUPPLY ARBITRATION VH, VPx VPx VH VDDCAP CVDDCAP POWER SUPPLY Supply Current, IVH, IVPx Additional Currents All PDO FET Drivers On Current Available from VDDCAP DAC Supply Currents ADC Supply Current EEPROM Erase Current SUPPLY FAULT DETECTORS VH Pin Input Impedance Input Attenuator Error Detection Ranges High Range Midrange VPx Pins Input Impedance Input Attenuator Error Detection Ranges Midrange Low Range Ultralow Range VXx Pins Input Impedance Detection Range Ultralow Range Absolute Accuracy Threshold Resolution Digital Glitch Filter ANALOG-TO-DIGITAL CONVERTER Signal Range 2.2 1 10 Min 3.0 6.0 14.4 5.4 Typ Max Unit V V V V F mA mA 2 mA mA mA mA Test Conditions/Comments Minimum supply required on one of the VH, VPx pins Maximum VDDCAP = 5.1 V, typical VDDCAP = 4.75 V Regulated LDO output Minimum recommended decoupling capacitance VDDCAP = 4.75 V, PDO1 to PDO10 off, DACs off, ADC off VDDCAP = 4.75 V, PDO1 to PDO6 loaded with 1 A each, PDO7 to PDO10 off Maximum additional load that can be drawn from all PDO pull-ups to VDDCAP Six DACs on with 100 A maximum load on each Running round-robin loop 1 ms duration only, VDDCAP = 3 V
2.7 10
4.75
4.2 1
52 0.05 6 2.5 52 0.05 2.5 1.25 0.573 1 0.573 1.375 1 8 0 100 0 VREFIN 6 3 1.375 14.4 6
k % V V k % V V V M V % Bits s s V
Midrange and high range
Low range and midrange
No input attenuation error
No input attenuation error VREF error + DAC nonlinearity + comparator offset error + input attenuation error Minimum programmable filter length Maximum programmable filter length The ADC can convert signals presented to the VH, VPx, and VXx pins; VPx and VH input signals are attenuated depending on the selected range; a signal at the pin corresponding to the selected range is from 0.573 V to 1.375 V at the ADC input
Input Reference Voltage on REFIN Pin, VREFIN Resolution INL Gain Error
2.048 12 2.5 0.05
V Bits LSB %
Endpoint corrected, VREFIN = 2.048 V VREFIN = 2.048 V
ADM1062
Parameter Conversion Time Offset Error Input Noise TEMPERATURE SENSOR 2 Local Sensor Accuracy Local Sensor Supply Voltage Coefficient Remote Sensor Accuracy Remote Sensor Supply Voltage Coefficient Remote Sensor Current Source Temperature for Code 0x800 Temperature for Code 0xC00 Temperature Resolution per Code BUFFERED VOLTAGE OUTPUT DACs Resolution Code 0x80 Output Voltage Range 1 Range 2 Range 3 Range 4 Output Voltage Range LSB Step Size INL DNL Gain Error Maximum Load Current (Source) Maximum Load Current (Sink) Maximum Load Capacitance Settling Time to 50 pF Load Load Regulation PSRR REFERENCE OUTPUT Reference Output Voltage Load Regulation Minimum Load Capacitance PSRR PROGRAMMABLE DRIVER OUTPUTS (PDOs) High Voltage (Charge Pump) Mode (PDO1 to PDO6) Output Impedance VOH IOUTAVG Standard (Digital Output) Mode (PDO1 to PDO10) VOH 0.592 0.796 0.996 1.246 Min Typ 0.44 84 0.25 3 1.7 3 3 200 12 0 128 0.125 8 Max Unit ms ms LSB LSB rms C C/V C C A A C C C Bits Six DACs are individually selectable for centering on one of four output voltage ranges 0.6 0.8 1 1.25 601.25 2.36 0.603 0.803 1.003 1.253 V V V V mV mV LSB LSB % A A pF s mV dB dB V mV mV F dB Test Conditions/Comments One conversion on one channel All 12 channels selected, 16 averaging enabled VREFIN = 2.048 V Direct input (no attenuator) VDDCAP = 4.75 V VDDCAP = 4.75 V High level Low level VDDCAP = 4.75 V VDDCAP = 4.75 V
Same range, independent of center point Endpoint corrected
0.75 0.4 1 100 100 50 2 2.5 60 40 2.043 2.048 0.25 +0.25 60 2.053
Per mA DC 100 mV step in 20 ns with 50 pF load No load Sourcing current, IDACxMAX = 100 A Sinking current, IDACxMAX = +100 A Capacitor required for decoupling, stability DC
11 10.5
500 12.5 12 20
14 13.5
k V V A
IOH = 0 A IOH = 1 A 2 V < VOH < 7 V
2.4 4.5 VPU 0.3 0
VOL
0.50
V V V V
VPU (pull-up to VDDCAP or VPx) = 2.7 V, IOH = 0.5 mA VPU to VPx = 6.0 V, IOH = 0 mA VPU 2.7 V, IOH = 0.5 mA IOL = 20 mA
ADM1062
Parameter IOL 3 ISINK3 RPULL-UP ISOURCE (VPx)3 Min Typ Max 20 60 29 2 Unit mA mA k mA Test Conditions/Comments Maximum sink current per PDOx pin Maximum total sink for all PDOx pins Internal pull-up Current load on any VPx pull-ups, that is, total source current available through any number of PDOx pull-up switches configured onto any one VPx pin VPDO = 14.4 V All on-chip time delays derived from this clock Maximum VIN = 5.5 V Maximum VIN = 5.5 V VIN = 5.5 V VIN = 0 V VDDCAP = 4.75 V TA = 25C if known logic state is required
16
20
Three-State Output Leakage Current Oscillator Frequency DIGITAL INPUTS (VXx, A0, A1) Input High Voltage, VIH Input Low Voltage, VIL Input High Current, IIH Input Low Current, IIL Input Capacitance Programmable Pull-Down Current, IPULL-DOWN SERIAL BUS DIGITAL INPUTS (SDA, SCL) Input High Voltage, VIH Input Low Voltage, VIL Output Low Voltage, VOL3 SERIAL BUS TIMING Clock Frequency, fSCLK Bus Free Time, tBUF Start Setup Time, tSU;STA Stop Setup Time, tSU;STO Start Hold Time, tHD;STA SCL Low Time, tLOW SCL High Time, tHIGH SCL, SDA Rise Time, tR SCL, SDA Fall Time, tF Data Setup Time, tSU;DAT Data Hold Time, tHD;DAT Input Low Current, IIL SEQUENCING ENGINE TIMING State Change Time
1 2
90 2.0
100
10 110
A kHz V V A A pF A V V V kHz s s s s s s s s ns ns A s
0.8 1 1 5 20 2.0 0.8 0.4 400 4.7 4.7 4 4 4.7 4 1000 300 250 5 1 10
IOUT = 3.0 mA
VIN = 0
At least one of the VH, VPx pins must be 3.0 V to maintain the device supply on VDDCAP. All temperature sensor measurements are taken with round-robin loop enabled and at least one other voltage input being measured. 3 Specification is not production tested but is supported by characterization data at initial product release.
ADM1062 ABSOLUTE MAXIMUM RATINGS

Table 2.
Parameter Voltage on VH Pin Voltage on VPx Pins Voltage on VXx Pins Voltage on A0, A1 Pins Voltage on REFIN, REFOUT Pins Voltage on VDDCAP, VCCP Pins Voltage on PDOx Pins Voltage on SDA, SCL Pins Voltage on GND, AGND, PDOGND, REFGND Pins Voltage on DN, DP Pins Input Current at Any Pin Package Input Current Maximum Junction Temperature (TJ max) Storage Temperature Range Lead Temperature, Soldering Vapor Phase, 60 sec ESD Rating, All Pins Rating 16 V 7V 0.3 V to +6.5 V 0.3 V to +7 V 5V 6.5 V 16 V 7V 0.3 V to +0.3 V 0.3 V to +5 V 5 mA 20 mA 150C 65C to +150C 215C 2000 V
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
THERMAL RESISTANCE
JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 3. Thermal Resistance
Package Type 40-Lead LFCSP 48-Lead TQFP JA 25 50 Unit C/W C/W
ESD CAUTION
ADM1062 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

PDOGND
PDOGND
38
VDDCAP
VDDCAP
VCCP
VCCP
39
GND
GND
SDA
SDA
SCL
SCL
DN
NC
DN
40
39
38
37
36
35
34
33
32
31 30 29 28
48
47
46
45
44
43
42
41
40
VX1 1 VX2 2 VX3 3 VX4 4 VX5 5 VP1 6 VP2 7 VP3 8 VP4 9 VH 10

11
PIN 1 INDICATOR
PDO1 PDO2 PDO3 PDO4 PDO5 PDO6 PDO7 PDO8 PDO9 PDO10
NC 1 VX1 2 VX2 3 VX3 4 VX4 5 VX5 6 VP1 7 VP2 8 VP3 9 VP4 10 VH 11 NC 12

04433-003
NC
37 36 NC 35 PDO1 34 PDO2 33 PDO3 32 PDO4 31 PDO5 30 PDO6 29 PDO7 28 PDO8 27 PDO9 26 PDO10 25 NC 24
DP
DP
A1
A0
A1
20
PIN 1 INDICATOR
ADM1062
TOP VIEW (Not to Scale)
27 26 25 24 23 22 21
ADM1062
TOP VIEW (Not to Scale)
12
13
14
15
16
17
18
19
20
REFGND
REFIN
REFOUT
AGND
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
13
14
15
16
17
18
19
A0
21
22
23
REFIN
REFOUT
NC
AGND
REFGND
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
NC
NC = NO CONNECT
Figure 3. LFCSP Pin Configuration
Figure 4. TQFP Pin Configuration
Table 4. Pin Function Descriptions

Pin No. LFCSP 1 TQFP 1, 12, 13, 24, 25, 36, 37, 48 1 to 5 2 to 6 6 to 9 7 to 10 Mnemonic NC Description No Connection.
VX1 to VX5 (VXx) VP1 to VP4 (VPx)
10
11
VH
11 12 13 14 15 to 20 21 to 30 31 32 33 34 35 36 37 38
14 15 16 17 18 to 23 26 to 35 38 39 40 41 42 43 44 45
AGND 2 REFGND2 REFIN REFOUT DAC1 to DAC6 PDO10 to PDO1 PDOGND2 VCCP A0 A1 SCL SDA DN DP
High Impedance Inputs to Supply Fault Detectors. Fault thresholds can be set from 0.573 V to 1.375 V. Alternatively, these pins can be used as general-purpose digital inputs. Low Voltage Inputs to Supply Fault Detectors. Three input ranges can be set by altering the input attenuation on a potential divider connected to these pins, the output of which connects to a supply fault detector. These pins allow thresholds from 2.5 V to 6.0 V, from1.25 V to 3.00 V, and from 0.573 V to 1.375 V. High Voltage Input to Supply Fault Detectors. Two input ranges can be set by altering the input attenuation on a potential divider connected to this pin, the output of which connects to a supply fault detector. This pin allows thresholds from 6.0 V to 14.4 V and from 2.5 V to 6.0 V. Ground Return for Input Attenuators. Ground Return for On-Chip Reference Circuits. Reference Input for ADC. Nominally, 2.048 V. This pin must be driven by a reference voltage. The on-board reference can be used by connecting the REFOUT pin to the REFIN pin. Reference Output, 2.048 V. Typically connected to REFIN. Note that the capacitor must be connected between this pin and REFGND. A 10 F capacitor is recommended for this purpose. Voltage Output DACs. These pins default to high impedance at power-up. Programmable Output Drivers. Ground Return for Output Drivers. Central Charge Pump Voltage of 5.25 V. A reservoir capacitor must be connected between this pin and GND. A 10 F capacitor is recommended for this purpose. Logic Input. This pin sets the seventh bit of the SMBus interface address. Logic Input. This pin sets the sixth bit of the SMBus interface address. SMBus Clock Pin. Bidirectional open drain requires external resistive pull-up. SMBus Data Pin. Bidirectional open drain requires external resistive pull-up. External Temperature Sensor Cathode Connection. External Temperature Sensor Anode Connection.
04433-004
ADM1062
Pin No. LFCSP 1 TQFP 39 46 Mnemonic VDDCAP Description Device Supply Voltage. Linearly regulated from the highest of the VPx, VH pins to a typical of 4.75 V. Note that the capacitor must be connected between this pin and GND. A 10 F capacitor is recommended for this purpose. Supply Ground.
40
1 2
47
GND2
Note that the LFCSP has an exposed pad on the bottom. This pad is a no connect (NC). If possible, this pad should be soldered to the board for improved mechanical stability. In a typical application, all ground pins are connected together.
ADM1062 TYPICAL PERFORMANCE CHARACTERISTICS

6
180 160
5
140
4
VVDDCAP (V)
IVP1 (A)
120 100 80 60 40
1
04433-050
04433-053
20 0
3 VVP1 (V)
3 VVP1 (V)
Figure 5. VVDDCAP vs. VVP1
Figure 8. IVP1 vs. VVP1 (VP1 Not as Supply)
5.0 4.5
4.0 3.5 3.0

IVH (mA)
04433-051
4
VVDDCAP (V)
2.5 2.0 1.5 1.0 0.5 0 0 2 4 6 8 VVH (V) 10 12 14 16

04433-054
8 VVH (V)
10
12
14
16
Figure 6. VVDDCAP vs. VVH
Figure 9. IVH vs. VVH (VH as Supply)
5.0 4.5 4.0 3.5

IVP1 (mA)
350 300 250 200 150 100 50 0
3.0 2.5 2.0 1.5 1.0 0.5 0 0 1 2 3 VVP1 (V) 4 5 6

04433-052
IVH (A)
3 VVH (V)
Figure 7. IVP1 vs. VVP1 (VP1 as Supply)
Figure 10. IVH vs. VVH (VH Not as Supply)
04433-055
ADM1062
14 12 CHARGE-PUMPED V PDO1 (V) 10
1.0 0.8 0.6 0.4
DNL (LSB)
8 6 4 2 0
0.2 0 0.2 0.4 0.6
04433-056
0.8 1.0 0 1000 2000 CODE 3000 4000
2.5
5.0
7.5 ILOAD (A)
10.0
12.5
15.0
Figure 11. Charge-Pumped VPDO1 (FET Drive Mode) vs. ILOAD
Figure 14. DNL for ADC
5.0 4.5 4.0 3.5

VPDO1 (V)
INL (LSB)
1.0 0.8 0.6 0.4 0.2 0 0.2 0.4 0.6 0.8 1.0 0 1000 2000 CODE 3000 4000
04433-063
3.0 VP1 = 5V 2.5 2.0 1.5 1.0 0.5 0 0 1 2 3 ILOAD (mA) 4 5 6

04433-057
VP1 = 3V
Figure 12. VPDO1 (Strong Pull-Up to VPx) vs. ILOAD
Figure 15. INL for ADC
4.5 4.0
12000 9894 10000
3.5 3.0 VPDO1 (V) 2.5 2.0 1.5 1.0

2000
04433-058 04433-064
VP1 = 5V HITS PER CODE
8000
VP1 = 3V
6000
4000
0.5 0
25 0 2047 2048 CODE
81 2049
10
20
30 ILOAD (A)
40
50
60
Figure 13. VPDO1 (Weak Pull-Up to VPx) vs. ILOAD
Figure 16. ADC Noise, Midcode Input, 10,000 Reads
04433-066
ADM1062
1.005 1.004 1.003 1.002
DAC OUTPUT
1.001 VP1 = 3.0V 1.000 0.999 0.998 0.997 0.996

04433-065
VP1 = 4.75V
DAC 20k BUFFER OUTPUT 47pF
PROBE POINT
04433-059
0.995 40
20
20
40
60
80
100
CH1 200mV
M1.00s
CH1
756mV
TEMPERATURE (C)
Figure 17. Transient Response of DAC Code Change into Typical Load
Figure 19. DAC Output vs. Temperature
2.058
2.053 VP1 = 3.0V 2.048 VP1 = 4.75V
DAC 100k BUFFER OUTPUT PROBE POINT
1V
REFOUT (V)
2.043
04433-061
04433-060
2.038 40
20
20
40
60
80
100
CH1 200mV
M1.00s
CH1
944mV
TEMPERATURE (C)
Figure 18. Transient Response of DAC to Turn-On from High-Z State
Figure 20. REFOUT vs. Temperature
ADM1062 POWERING THE ADM1062

The ADM1062 is powered from the highest voltage input on either the positive-only supply inputs (VPx) or the high voltage supply input (VH). This technique offers improved redundancy because the device is not dependent on any particular voltage rail to keep it operational. The same pins are used for supply fault detection (see the Supply Supervision section). A VDD arbitrator on the device chooses which supply to use. The arbitrator can be considered an ORing of five low dropout regulators (LDOs) together. A supply comparator chooses the highest input to provide the on-chip supply. There is minimal switching loss with this architecture (~0.2 V), resulting in the ability to power the ADM1062 from a supply as low as 3.0 V. Note that the supply on the VXx pins cannot be used to power the device. An external capacitor to GND is required to decouple the on-chip supply from noise. This capacitor should be connected to the VDDCAP pin, as shown in Figure 21. The capacitor has another use during brownouts (momentary loss of power). Under these conditions, when the input supply (VPx or VH) dips transiently below VDD, the synchronous rectifier switch immediately turns off so that it does not pull VDD down. The VDD capacitor can then act as a reservoir to keep the device active until the next highest supply takes over the powering of the device. A 10 F capacitor is recommended for this reservoir/decoupling function. The VH input pin can accommodate supplies up to 14.4 V, which allows the ADM1062 to be powered using a 12 V backplane supply. In cases where this 12 V supply is hot swapped, it is recommended that the ADM1062 not be connected directly to the supply. Suitable precautions, such as the use of a hot swap controller, should be taken to protect the device from transients that could cause damage during hot swap events. When two or more supplies are within 100 mV of each other, the supply that first takes control of VDD keeps control. For example, if VP1 is connected to a 3.3 V supply, VDD powers up to approximately 3.1 V through VP1. If VP2 is then connected to another 3.3 V supply, VP1 still powers the device, unless VP2 goes 100 mV higher than VP1.
VDDCAP VP1 IN EN VP2 IN EN VP3 IN EN VP4 IN EN VH IN EN SUPPLY COMPARATOR
04433-022
OUT 4.75V LDO OUT 4.75V LDO OUT 4.75V LDO OUT 4.75V LDO OUT 4.75V LDO INTERNAL DEVICE SUPPLY
Figure 21. VDD Arbitrator Operation
ADM1062 INPUTS
SUPPLY SUPERVISION
The ADM1062 has 10 programmable inputs. Five of these are dedicated supply fault detectors (SFDs). These dedicated inputs are called VH and VPx (VP1 to VP4) by default. The other five inputs are labeled VXx (VX1 to VX5) and have dual functionality. They can be used either as SFDs, with functionality similar to VH and VPx, or as CMOS-/TTL-compatible logic inputs to the device. Therefore, the ADM1062 can have up to 10 analog inputs, a minimum of five analog inputs and five digital inputs, or a combination thereof. If an input is used as an analog input, it cannot be used as a digital input. Therefore, a configuration requiring 10 analog inputs has no available digital inputs. Table 6 shows the details of each input. The threshold value required is given by VT = (VR N)/255 + VB where: VT is the desired threshold voltage (undervoltage or overvoltage). VR is the voltage range. N is the decimal value of the 8-bit code. VB is the bottom of the range. Reversing the equation, the code for a desired threshold is given by N = 255 (VT VB)/VR For example, if the user wants to set a 5 V overvoltage threshold on VP1, the code to be programmed in the PS1OVTH register (as discussed in the AN-698 Application Note at www.analog.com) is given by N = 255 (5 2.5)/3.5 Therefore, N = 182 (1011 0110 or 0xB6).
PROGRAMMING THE SUPPLY FAULT DETECTORS

The ADM1062 can have up to 10 SFDs on its 10 input channels. These highly programmable reset generators enable the supervision of up to 10 supply voltages. The supplies can be as low as 0.573 V and as high as 14.4 V. The inputs can be configured to detect an undervoltage fault (the input voltage drops below a preprogrammed value), an overvoltage fault (the input voltage rises above a preprogrammed value), or an out-of-window fault (the input voltage is outside a preprogrammed range). The thresholds can be programmed to an 8-bit resolution in registers provided in the ADM1062. This translates to a voltage resolution that is dependent on the range selected. The resolution is given by Step Size = Threshold Range/255 Therefore, if the high range is selected on VH, the step size can be calculated as follows: (14.4 V 6.0 V)/255 = 32.9 mV Table 5 lists the upper and lower limits of each available range, the bottom of each range (VB), and the range itself (VR). Table 5. Voltage Range Limits
Voltage Range (V) 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 6.0 to 14.4 VB (V) 0.573 1.25 2.5 6.0 VR (V) 0.802 1.75 3.5 8.4
INPUT COMPARATOR HYSTERESIS

The UV and OV comparators shown in Figure 22 are always monitoring VPx. To avoid chatter (multiple transitions when the input is very close to the set threshold level), these comparators have digitally programmable hysteresis. The hysteresis can be programmed up to the values shown in Table 6.
RANGE SELECT ULTRA LOW VPx VREF + OV COMPARATOR GLITCH FILTER FAULT OUTPUT
+ LOW MID FAULT TYPE UV SELECT COMPARATOR

04433-023
Figure 22. Supply Fault Detector Block
The hysteresis is added after a supply voltage goes out of tolerance. Therefore, the user can program the amount above the undervoltage threshold to which the input must rise before an undervoltage fault is deasserted. Similarly, the user can program the amount below the overvoltage threshold to which an input must fall before an overvoltage fault is deasserted.
Table 6. Input Functions, Thresholds, and Ranges

Input VH VPx Function High Voltage Analog Input Positive Analog Input Voltage Range (V) 2.5 to 6.0 6.0 to 14.4 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 0.573 to 1.375 0 to 5.0 Maximum Hysteresis 425 mV 1.02 V 97.5 mV 212 mV 425 mV 97.5 mV N/A Voltage Resolution (mV) 13.7 32.9 3.14 6.8 13.7 3.14 N/A Glitch Filter (s) 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100
VXx
High-Z Analog Input Digital Input
ADM1062
The hysteresis value is given by VHYST = VR NTHRESH/255 where: VHYST is the desired hysteresis voltage. NTHRESH is the decimal value of the 5-bit hysteresis code. Note that NTHRESH has a maximum value of 31. The maximum hysteresis for the ranges is listed in Table 6. An additional supply supervision function is available when the VXx pins are selected as digital inputs. In this case, the analog function is available as a second detector on each of the dedicated analog inputs, VPx and VH. The analog function of VX1 is mapped to VP1, VX2 is mapped to VP2, and so on; VX5 is mapped to VH. In this case, these SFDs can be viewed as secondary or warning SFDs. The secondary SFDs are fixed to the same input range as the primary SFDs. They are used to indicate warning levels rather than failure levels. This allows faults and warnings to be generated on a single supply using only one pin. For example, if VP1 is set to output a fault when a 3.3 V supply drops to 3.0 V, VX1 can be set to output a warning at 3.1 V. Warning outputs are available for readback from the status registers. They are also ORed together and fed into the SE, allowing warnings to generate interrupts on the PDOs. Therefore, in this example, if the supply drops to 3.1 V, a warning is generated and remedial action can be taken before the supply drops out of tolerance.
INPUT GLITCH FILTERING

The final stage of the SFDs is a glitch filter. This block provides time-domain filtering on the output of the SFD comparators, which allows the user to remove any spurious transitions, such as supply bounce at turn-on. The glitch filter function is in addition to the digitally programmable hysteresis of the SFD comparators. The glitch filter timeout is programmable up to 100 s. For example, when the glitch filter timeout is 100 s, any pulse appearing on the input of the glitch filter block that is less than 100 s in duration is prevented from appearing on the output of the glitch filter block. Any input pulse that is longer than 100 s appears on the output of the glitch filter block. The output is delayed with respect to the input by 100 s. The filtering process is shown in Figure 23.
INPUT PULSE SHORTER THAN GLITCH FILTER TIMEOUT PROGRAMMED TIMEOUT INPUT PULSE LONGER THAN GLITCH FILTER TIMEOUT PROGRAMMED TIMEOUT
VXx PINS AS DIGITAL INPUTS

As discussed in the Supply Supervision with VXX Inputs section, the VXx input pins on the ADM1062 have dual functionality. The second function is as a digital logic input to the device. Therefore, the ADM1062 can be configured for up to five digital inputs. These inputs are TTL-/CMOS-compatible. Standard logic signals can be applied to the pins: RESET from reset generators, PWRGD signals, fault flags, manual resets, and so on. These signals are available as inputs to the SE and, therefore, can be used to control the status of the PDOs. The inputs can be configured to detect either a change in level or an edge. When configured for level detection, the output of the digital block is a buffered version of the input. When configured for edge detection, a pulse of programmable width is output from the digital block once the logic transition is detected. The width is programmable from 0 s to 100 s.
INPUT
INPUT
t0
tGF
t0
tGF
OUTPUT
OUTPUT
04433-024
t0
tGF
t0
tGF
Figure 23. Input Glitch Filter Function
The digital blocks feature the same glitch filter function that is available on the SFDs. This function enables the user to ignore spurious transitions on the inputs. For example, the filter can be used to debounce a manual reset switch. When configured as digital inputs, each VXx pin has a weak (10 A) pull-down current source available for placing the input into a known condition, even if left floating. The current source, if selected, weakly pulls the input to GND.
VXx (DIGITAL INPUT) + DETECTOR
04433-027
SUPPLY SUPERVISION WITH VXx INPUTS

The VXx inputs have two functions. They can be used as either supply fault detectors or digital logic inputs. When selected as analog (SFD) inputs, the VXx pins have functionality that is very similar to the VH and VPx pins. The primary difference is that the VXx pins have only one input range: 0.573 V to 1.375 V. Therefore, these inputs can directly supervise only the very low supplies. However, the input impedance of the VXx pins is high, allowing an external resistor divide network to be connected to the pin. Thus, potentially any supply can be divided down into the input range of the VXx pin and supervised, enabling the ADM1062 to monitor other supplies, such as +24 V, +48 V, and 5 V.
GLITCH FILTER
TO SEQUENCING ENGINE
VREF = 1.4V
Figure 24. VXx Digital Input Function
ADM1062 OUTPUTS
SUPPLY SEQUENCING THROUGH CONFIGURABLE OUTPUT DRIVERS
Supply sequencing is achieved with the ADM1062 using the programmable driver outputs (PDOs) on the device as control signals for supplies. The output drivers can be used as logic enables or as FET drivers. The sequence in which the PDOs are asserted (and, therefore, the supplies are turned on) is controlled by the sequencing engine (SE). The SE determines what action is taken with the PDOs, based on the condition of the ADM1062 inputs. Therefore, the PDOs can be set up to assert when the SFDs are in tolerance, the correct input signals are received on the VXx digital pins, no warnings are received from any of the inputs of the device, and at other times. The PDOs can be used for a variety of functions. The primary function is to provide enable signals for LDOs or dc-to-dc converters that generate supplies locally on a board. The PDOs can also be used to provide a PWRGD signal, when all the SFDs are in tolerance, or a RESET output if one of the SFDs goes out of specification (this can be used as a status signal for a DSP, FPGA, or other microcontroller). The PDOs can be programmed to pull up to a number of different options. The outputs can be programmed as follows: Open-drain (allowing the user to connect an external pull-up resistor). Open-drain with weak pull-up to VDD. Open-drain with strong pull-up to VDD. Open-drain with weak pull-up to VPx. Open-drain with strong pull-up to VPx. Strong pull-down to GND. Internally charge-pumped high drive (12 V, PDO1 to PDO6 only). register (see the AN-698 Application Note at www.analog.com for details). The data sources are as follows: Output from the SE. Directly from the SMBus. A PDO can be configured so that the SMBus has direct control over it. This enables software control of the PDOs. Therefore, a microcontroller can be used to initiate a software power-up/power-down sequence. On-chip clock. A 100 kHz clock is generated on the device. This clock can be made available on any of the PDOs. It can be used, for example, to clock an external device such as an LED.
DEFAULT OUTPUT CONFIGURATION

All of the internal registers in an unprogrammed ADM1062 device from the factory are set to 0. Because of this, the PDOx pins are pulled to GND by a weak (20 k) on-chip pull-down resistor. As the input supply to the ADM1062 ramps up on VPx or VH, all the PDOx pins behave as follows: Input supply = 0 V to 1.2 V. The PDOs are high impedance. Input supply = 1.2 V to 2.7 V. The PDOs are pulled to GND by a weak (20 k) on-chip pull-down resistor. Supply > 2.7 V. Factory-programmed devices continue to pull all PDOs to GND by a weak (20 k) on-chip pull-down resistor. Programmed devices download current EEPROM configuration data, and the programmed setup is latched. The PDO then goes to the state demanded by the configuration. This provides a known condition for the PDOs during power-up. The internal pull-down can be overdriven with an external pull-up of suitable value tied from the PDOx pin to the required pull-up voltage. The 20 k resistor must be accounted for in calculating a suitable value. For example, if PDOx must be pulled up to 3.3 V, and 5 V is available as an external supply, the pull-up resistor value is given by 3.3 V = 5 V 20 k/(RUP + 20 k) Therefore, RUP = (100 k 66 k)/3.3 V = 10 k
VFET (PDO1 TO PDO6 ONLY) VP4 VDD
The last option (available only on PDO1 to PDO6) allows the user to directly drive a voltage high enough to fully enhance an external N-FET, which is used to isolate, for example, a cardside voltage from a backplane supply (a PDO can sustain greater than 10.5 V into a 1 A load). The pull-down switches can also be used to drive status LEDs directly. The data driving each of the PDOs can come from one of three sources. The source can be enabled in the PDOxCFG configuration
CFG4 CFG5 CFG6
SEL
VP1
20k
20k
SE DATA SMBus DATA CLK DATA PDO
20k 20k
10
10
10
Figure 25. Programmable Driver Output

04433-028
ADM1062 SEQUENCING ENGINE

OVERVIEW
The ADM1062 sequencing engine (SE) provides the user with powerful and flexible control of sequencing. The SE implements a state machine control of the PDO outputs, with state changes conditional on input events. SE programs can enable complex control of boards, including power-up and power-down sequence control, fault event handling, and interrupt generation on warnings. A watchdog function that verifies the continued operation of a processor clock can be integrated into the SE program. The SE can also be controlled via the SMBus, giving software or firmware control of the board sequencing. The SE state machine comprises 63 state cells. Each state has the following attributes: Monitors signals indicating the status of the 10 input pins, VP1 to VP4, VH, and VX1 to VX5. Can be entered from any other state. Three exit routes move the state machine onto the next state: sequence detection, fault monitoring, and timeout. Delay timers for the sequence and timeout blocks can be programmed independently and changed with each state change. The range of timeouts is from 0 ms to 400 ms. Output condition of the 10 PDO pins is defined and fixed within a state. Transition from one state to the next is made in less than 20 s, which is the time needed to download a state definition from EEPROM to the SE.
MONITOR FAULT STATE TIMEOUT
SEQUENCE
Figure 26. State Cell
The ADM1062 offers up to 63 state definitions. The signals monitored to indicate the status of the input pins are the outputs of the SFDs.
WARNINGS
The SE also monitors warnings. These warnings can be generated when the ADC readings violate their limit register value or when the secondary voltage monitors on VPx and VH are triggered. The warnings are ORed together and are available as a single warning input to each of the three blocks that enable exiting a state.
SMBus JUMP (UNCONDITIONAL JUMP)

The SE can be forced to advance to the next state unconditionally. This enables the user to force the SE to advance. Examples of the use of this feature include moving to a margining state or debugging a sequence. The SMBus jump or go-to command can be seen as another input to sequence and timeout blocks to provide an exit from each state.
Table 7. Sample Sequence State Entries

State IDLE1 IDLE2 EN3V3 DIS3V3 EN2V5 DIS2V5 FSEL1 FSEL2 PWRGD Sequence If VX1 is low, go to State IDLE2. If VP1 is okay, go to State EN3V3. If VP2 is okay, go to State EN2V5. If VX1 is high, go to State IDLE1. If VP3 is okay, go to State PWRGD. If VX1 is high, go to State IDLE1. If VP3 is not okay, go to State DIS2V5. If VP2 is not okay, go to State DIS3V3. If VX1 is high, go to State DIS2V5. Timeout Monitor
If VP2 is not okay after 10 ms, go to State DIS3V3. If VP3 is not okay after 20 ms, go to State DIS2V5.
If VP1 is not okay, go to State IDLE1.
If VP1 or VP2 is not okay, go to State FSEL2.
If VP1 or VP2 is not okay, go to State FSEL2. If VP1 is not okay, go to State IDLE1. If VP1, VP2, or VP3 is not okay, go to State FSEL1.
04433-029
ADM1062
SEQUENCING ENGINE APPLICATION EXAMPLE
The application in this section demonstrates operation of the SE. Figure 28 shows how the simple building block of a single SE state can be used to build a power-up sequence for a threesupply system. Table 8 lists the PDO outputs for each state in the same SE implementation. In this system, a good 5 V supply on the VP1 pin and the VX1 pin held low are the triggers required to start a power-up sequence. The sequence next turns on the 3.3 V supply, then the 2.5 V supply (assuming successful turn-on of the 3.3 V supply). When all three supplies are have turned on correctly, the PWRGD state is entered, where the SE remains until a fault occurs on one of the three supplies, or until it is instructed to go through a power-down sequence by VX1 going high. Faults are dealt with throughout the power-up sequence on a case-by-case basis. The following three sections (the Sequence Detector section, the Monitoring Fault Detector section, and the Timeout Detector section) describe the individual blocks and use the sample application shown in Figure 28 to demonstrate the actions of the state machine. If a timer delay is specified, the input to the sequence detector must remain in the defined state for the duration of the timer delay. If the input changes state during the delay, the timer is reset. The sequence detector can also help to identify monitoring faults. In the sample application shown in Figure 28, the FSEL1 and FSEL2 states first identify which of the VP1, VP2, or VP3 pins has faulted, and then they take appropriate action.
SEQUENCE STATES
IDLE1
VX1 = 0
IDLE2
MONITOR FAULT STATES
VP1 = 1
TIMEOUT STATES
Sequence Detector
The sequence detector block is used to detect when a step in a sequence has been completed. It looks for one of the SE inputs to change state and is most often used as the gate for successful progress through a power-up or power-down sequence. A timer block that is included in this detector can insert delays into a power-up or power-down sequence, if required. Timer delays can be set from 10 s to 400 ms. Figure 27 is a block diagram of the sequence detector.
VP1 SUPPLY FAULT DETECTION SEQUENCE DETECTOR
(VP1 + VP2) = 0 VP1 = 0
EN3V3
10ms
VP2 = 1
EN2V5
(VP1 + VP2) = 0 20ms
DIS3V3
VX1 = 1
VP3 = 1
PWRGD
VP2 = 0 (VP1 + VP2 + VP3) = 0
DIS2V5
VX1 = 1
FSEL1
VX1 = 1
VX5
LOGIC INPUT CHANGE OR FAULT DETECTION TIMER WARNINGS INVERT FORCE FLOW (UNCONDITIONAL JUMP) SELECT
04433-032
VP3 = 0
FSEL2
VP1 = 0 VP2 = 0
04433-030
Figure 28. Sample Application Flow Diagram
Figure 27. Sequence Detector Block Diagram
Table 8. PDO Outputs for Each State

PDO Outputs PDO1 = 3V3ON PDO2 = 2V5ON PDO3 = FAULT IDLE1 0 0 0 IDLE2 0 0 0 EN3V3 1 0 0 EN2V5 1 1 0 DIS3V3 0 1 1 DIS2V5 1 0 1 PWRGD 1 1 0 FSEL1 1 1 1 FSEL2 1 1 1
ADM1062
Monitoring Fault Detector
The monitoring fault detector block is used to detect a failure on an input. The logical function implementing this is a wide OR gate that can detect when an input deviates from its expected condition. The clearest demonstration of the use of this block is in the PWRGD state, where the monitor block indicates that a failure on one or more of the VP1, VP2, or VP3 inputs has occurred. No programmable delay is available in this block because the triggering of a fault condition is likely to be caused by a supply falling out of tolerance. In this situation, the device needs to react as quickly as possible. Some latency occurs when moving out of this state because it takes a finite amount of time (~20 s) for the state configuration to download from the EEPROM into the SE. Figure 29 is a block diagram of the monitoring fault detector.
MONITORING FAULT DETECTOR 1-BIT FAULT DETECTOR VP1 SUPPLY FAULT DETECTION MASK SENSE FAULT
Timeout Detector
The timeout detector allows the user to trap a failure to ensure proper progress through a power-up or power-down sequence. In the sample application shown in Figure 28, the timeout nextstate transition is from the EN3V3 and EN2V5 states. For the EN3V3 state, the signal 3V3ON is asserted on the PDO1 output pin upon entry to this state to turn on a 3.3 V supply. This supply rail is connected to the VP2 pin, and the sequence detector looks for the VP2 pin to go above its undervoltage threshold, which is set in the supply fault detector (SFD) attached to that pin. The power-up sequence progresses when this change is detected. If, however, the supply fails (perhaps due to a short circuit overloading this supply), the timeout block traps the problem. In this example, if the 3.3 V supply fails within 10 ms, the SE moves to the DIS3V3 state and turns off this supply by bringing PDO1 low. It also indicates that a fault has occurred by taking PDO3 high. Timeout delays of 100 s to 400 ms can be programmed.
FAULT AND STATUS REPORTING

The ADM1062 has a fault latch for recording faults. Two registers, FSTAT1 and FSTAT2, are set aside for this purpose. A single bit is assigned to each input of the device, and a fault on that input sets the relevant bit. The contents of the fault register can be read out over the SMBus to determine which input(s) faulted. The fault register can be enabled or disabled in each state. To latch data from one state, ensure that the fault latch is disabled in the following state. This ensures that only real faults are captured and not, for example, undervoltage conditions that may be present during a power-up or power-down sequence. The ADM1062 also has a number of status registers. These include more detailed information, such as whether an undervoltage or overvoltage fault is present on a particular input. The status registers also include information on ADC limit faults. Note that the data in the status registers is not latched in any way and, therefore, is subject to change at any time. See the AN-698 Application Note at www.analog.com for full details about the ADM1062 registers.
1-BIT FAULT DETECTOR VX5 LOGIC INPUT CHANGE OR FAULT DETECTION MASK SENSE 1-BIT FAULT DETECTOR WARNINGS FAULT FAULT
MASK
Figure 29. Monitoring Fault Detector Block Diagram
04433-033
ADM1062 VOLTAGE READBACK

The ADM1062 has an on-board, 12-bit, accurate ADC for voltage readback over the SMBus. The ADC has a 12-channel analog mux on the front end. The 12 channels consist of the 10 SFD inputs (VH, VPx, and VXx), plus two channels for temperature readback (see the Temperature Measurement System section). Any or all of these inputs can be selected to be read, in turn, by the ADC. The circuit controlling this operation is called the round-robin circuit. This circuit can be selected to run through its loop of conversions once or continuously. Averaging is also provided for each channel. In this case, the round-robin circuit runs through its loop of conversions 16 times before returning a result for each channel. At the end of this cycle, the results are written to the output registers. The ADC samples single-sided inputs with respect to the AGND pin. A 0 V input gives out Code 0, and an input equal to the voltage on REFIN gives out full code (4095 decimal). The inputs to the ADC come directly from the VXx pins and from the back of the input attenuators on the VPx and VH pins, as shown in Figure 30 and Figure 31.
NO ATTENUATION VXx 12-BIT ADC
04433-025
Table 9. ADC Input Voltage Ranges

SFD Input Range (V) 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 6.0 to 14.4
1
Attenuation Factor 1 2.181 4.363 10.472
ADC Input Voltage Range (V) 0 to 2.048 0 to 4.46 0 to 6.01 0 to 14.41
The upper limit is the absolute maximum allowed voltage on the VPx and VH pins.
The typical way to supply the reference to the ADC on the REFIN pin is to connect the REFOUT pin to the REFIN pin. REFOUT provides a 2.048 V reference. As such, the supervising range covers less than half the normal ADC range. It is possible, however, to provide the ADC with a more accurate external reference for improved readback accuracy. Supplies can also be connected to the input pins purely for ADC readback, even though these pins may go above the expected supervisory range limits (but not above the absolute maximum ratings on these pins). For example, a 1.5 V supply connected to the VX1 pin can be correctly read out as an ADC code of approximately 3/4 full scale, but it always sits above any supervisory limits that can be set on that pin. The maximum setting for the REFIN pin is 2.048 V.
DIGITIZED VOLTAGE READING
2.048V VREF
SUPPLY SUPERVISION WITH THE ADC

In addition to the readback capability, another level of supervision is provided by the on-chip, 12-bit ADC. The ADM1062 has limit registers with which the user can program a maximum or minimum allowable threshold. Exceeding the threshold generates a warning that can either be read back from the status registers or input into the SE to determine what sequencing action the ADM1062 should take. Only one register is provided for each input channel. Therefore, either an undervoltage threshold or overvoltage threshold (but not both) can be set for a given channel. The round-robin circuit can be enabled via an SMBus write, or it can be programmed to turn on in any state in the SE program. For example, it can be set to start after a power-up sequence is complete, and all supplies are known to be within expected tolerance limits. Note that a latency is built into this supervision, dictated by the conversion time of the ADC. With all 12 channels selected, the total time for the round-robin operation (averaging off) is approximately 6 ms (500 s per channel selected). Supervision using the ADC, therefore, does not provide the same real-time response as the SFDs.
Figure 30. ADC Reading on VXx Pins
VPx/VH
ATTENUATION NETWORK (DEPENDS ON RANGE SELECTED) DIGITIZED VOLTAGE READING 12-BIT ADC
04433-026
2.048V VREF
Figure 31. ADC Reading on VPx/VH Pins
The voltage at the input pin can be derived from the following equation: V=
ADC Code 4095
Attenuation Factor VREFIN
where VREFIN = 2.048 V when the internal reference is used (that is, the REFIN pin is connected to the REFOUT pin). The ADC input voltage ranges for the SFD input ranges are listed in Table 9.
ADM1062 SUPPLY MARGINING

OVERVIEW
It is often necessary for the system designer to adjust supplies, either to optimize their level or force them away from nominal values to characterize the system performance under these conditions. This is a function typically performed during an in-circuit test (ICT), such as when a manufacturer wants to guarantee that a product under test functions correctly at nominal supplies minus 10%.
CLOSED-LOOP SUPPLY MARGINING

A more accurate and comprehensive method of margining is to implement a closed-loop system (see Figure 33). The voltage on the rail to be margined can be read back to accurately margin the rail to the target voltage. The ADM1062 incorporates all the circuits required to do this, with the 12-bit successive approximation ADC used to read back the level of the supervised voltages, and the six voltage output DACs, implemented as described in the Open-Loop Supply Margining section, used to adjust supply levels. These circuits can be used along with other intelligence, such as a microcontroller, to implement a closed-loop margining system that allows any dc-to-dc converter or LDO supply to be set to any voltage, accurate to within 0.5% of the target. To implement closed-loop margining 1. 2. 3. 4. 5. Disable the six DACx outputs. Set the DAC output voltage equal to the voltage on the feedback node. Enable the DAC. Read the voltage at the dc-to-dc converter output that is connected to one of the VPx, VH, or VXx pins. If necessary, modify the DACx output code up or down to adjust the dc-to-dc converter output voltage. Otherwise, stop because the target voltage has been reached. Set the DAC output voltage to a value that alters the supply output by the required amount (for example, 5%). Repeat Step 4 through Step 6 until the measured supply reaches the target voltage.
OPEN-LOOP SUPPLY MARGINING

The simplest method of margining a supply is to implement an open-loop technique (see Figure 32). A popular way to do this is to switch extra resistors into the feedback node of a power module, such as a dc-to-dc converter or LDO. The extra resistor alters the voltage at the feedback or trim node and forces the output voltage to margin up or down by a certain amount. The ADM1062 can perform open-loop margining for up to six supplies. The six on-board voltage DACs (DAC1 to DAC6) can drive into the feedback pins of the power modules to be margined. The simplest circuit to implement this function is an attenuation resistor that connects the DACx pin to the feedback node of a dc-to-dc converter. When the DACx output voltage is set equal to the feedback voltage, no current flows into the attenuation resistor, and the dc-to-dc converter output voltage does not change. Taking DACx above the feedback voltage forces current into the feedback node, and the output of the dc-to-dc converter is forced to fall to compensate for this. The dc-to-dc converter output can be forced high by setting the DACx output voltage lower than the feedback node voltage. The series resistor can be split in two, and the node between them can be decoupled with a capacitor to ground. This can help to decouple any noise picked up from the board. Decoupling to a ground local to the dc-to-dc converter is recommended. The ADM1062 can be commanded to margin a supply up or down over the SMBus by updating the values on the relevant DAC output.
VIN
6. 7.
Step 1 to Step 3 ensure that when the DACx output buffer is turned on, it has little effect on the dc-to-dc converter output. The DAC output buffer is designed to power up without glitching by first powering up the buffer to follow the pin voltage. It does not drive out onto the pin at this time. Once the output buffer is properly enabled, the buffer input is switched over to the DAC, and the output stage of the buffer is turned on. Output glitching is negligible.
MICROCONTROLLER
VOUT OUTPUT DC-TO-DC CONVERTER FEEDBACK GND ATTENUATION RESISTOR DACx PCB TRACE NOISE DECOUPLING CAPACITOR
ADM1062
DEVICE CONTROLLER (SMBus) DAC
Figure 32. Open-Loop Margining System Using the ADM1062
04433-067
ADM1062
VIN MICROCONTROLLER
ADM1062
DC-TO-DC CONVERTER OUTPUT R1 FEEDBACK R2 GND ATTENUATION RESISTOR, R3 DACx PCB TRACE NOISE DECOUPLING CAPACITOR VH/VPx/VXx MUX ADC DEVICE CONTROLLER (SMBus)
DAC
Figure 33. Closed-Loop Margining System Using the ADM1062
WRITING TO THE DACS

Four DAC ranges are offered. They can be placed with midcode (Code 0x7F) at 0.6 V, 0.8 V, 1.0 V, and 1.25 V. These voltages are placed to correspond to the most common feedback voltages. Centering the DAC outputs in this way provides the best use of the DAC resolution. For most supplies, it is possible to place the DAC midcode at the point where the dc-to-dc converter output is not modified, thereby giving half of the DAC range to margin up and the other half to margin down. The DAC output voltage is set by the code written to the DACx register. The voltage is linear with the unsigned binary number in this register. Code 0x7F is placed at the midcode voltage, as described previously. The output voltage is given by the following equation: DAC Output = (DACx 0x7F)/255 0.6015 + VOFF where VOFF is one of the four offset voltages. There are 256 DAC settings available. The midcode value is located at DAC Code 0x7F, as close as possible to the middle of the 256 code range. The full output swing of the DACs is +302 mV (+128 codes) and 300 mV (127 codes) around the selected midcode voltage. The voltage range for each midcode voltage is shown in Table 10.
Table 10. Ranges for Midcode Voltages
Midcode Voltage (V) 0.6 0.8 1.0 1.25 Minimum Voltage Output (V) 0.300 0.500 0.700 0.950 Maximum Voltage Output (V) 0.902 1.102 1.302 1.552
the current flowing through R3. Therefore, a direct relationship exists between the extra voltage drop across R1 during margining and the voltage drop across R3. This relationship is given by the following equation: VOUT =
R1 (VFB VDACOUT) R3
where: VOUT is the change in VOUT. VFB is the voltage at the feedback node of the dc-to-dc converter. VDACOUT is the voltage output of the margining DAC. This equation demonstrates that if the user wants the output voltage to change by 300 mV, then R1 = R3. If the user wants the output voltage to change by 600 mV, then R1 = 2 R3, and so on. It is best to use the full DAC output range to margin a supply. Choosing the attenuation resistor in this way provides the most resolution from the DAC, meaning that with one DAC code change, the smallest effect on the dc-to-dc converter output voltage is induced. If the resistor is sized up to use a code such as 27 decimal to 227 decimal to move the dc-to-dc converter output by 5%, it takes 100 codes to move 5% (each code moves the output by 0.05%). This is beyond the readback accuracy of the ADC, but it should not prevent the user from building a circuit to use the most resolution.
DAC LIMITING AND OTHER SAFETY FEATURES

Limit registers (called DPLIMx and DNLIMx) on the device offer the user some protection from firmware bugs that can cause catastrophic board problems by forcing supplies beyond their allowable output ranges. Essentially, the DAC code written into the DACx register is clipped such that the code used to set the DAC voltage is given by
DAC Code = DACx, DACx DNLIMx and DACx DPLIMx = DNLIMx, DACx < DNLIMx = DPLIMx, DACx > DPLIMx
CHOOSING THE SIZE OF THE ATTENUATION RESISTOR

The size of the attenuation resistor, R3, determines how much the DAC voltage swing affects the output voltage of the dc-to-dc converter that is being margined (see Figure 33). Because the voltage at the feedback pin remains constant, the current flowing from the feedback node to GND through R2 is a constant. In addition, the feedback node itself is high impedance. This means that the current flowing through R1 is the same as
In addition, the DAC output buffer is three-stated if DNLIMx > DPLIMx. By programming the limit registers this way, the user can make it very difficult for the DAC output buffers to be turned on during normal system operation. The limit registers are among the registers downloaded from the EEPROM at startup.
04433-034
ADM1062 TEMPERATURE MEASUREMENT SYSTEM

The ADM1062 contains an on-chip, band gap temperature sensor whose output is digitized by the on-chip, 12-bit ADC. Theoretically, the temperature sensor and the ADC can measure temperatures from 128C to +128C with a resolution of 0.125C. Because this exceeds the operating temperature range of the device, local temperature measurements outside this range are not possible. Temperature measurements from 128C to +128C are possible using a remote sensor. The output code is in offset binary format, with 128C given by Code 0x400, 0C given by Code 0x800, and +128C given by Code 0xC00. As with the other analog inputs to the ADC, a limit register is provided for each of the temperature input channels. Therefore, a temperature limit can be set such that if it is exceeded, a warning is generated and available as an input to the sequencing engine. This enables users to control their sequence or monitor functions based on an overtemperature or undertemperature event. Figure 36 shows the input signal conditioning used to measure the output of a remote temperature sensor. This figure shows the external sensor as a substrate transistor provided for temperature monitoring on some microprocessors, but it could equally be a discrete transistor such as a 2N3904 or 2N3906. If a discrete transistor is used, the collector is not grounded and should be linked to the base. If a PNP transistor is used, the base is connected to the DN input, and the emitter is connected to the DP input. If an NPN transistor is used, the emitter is connected to the DN input, and the base is connected to the DP input. Figure 34 and Figure 35 show how to connect the ADM1062 to an NPN or PNP transistor for temperature measurement. To prevent ground noise from interfering with the measurement, the more negative terminal of the sensor is not referenced to ground but is biased above ground by an internal diode at the DN input.
ADM1062
2N3904 NPN DP
04433-070
REMOTE TEMPERATURE MEASUREMENT

The ADM1062 can measure the temperature of a remote diode sensor or diode-connected transistor connected to Pin DN and Pin DP (Pin 37 and Pin 38 on the LFCSP package and Pin 44 and Pin 45 on the TQFP package). The forward voltage of a diode or diode-connected transistor operated at a constant current exhibits a negative temperature coefficient of about 2 mV/C. Unfortunately, the absolute value of VBE varies from device to device, and individual calibration is required to null it, making the technique unsuitable for mass production. The technique used in the ADM1062 is to measure the change in VBE when the device is operated at two different currents. The change in VBE is given by VBE = kT/q ln(N) where: k is Boltzmanns constant. q is the charge on the carrier. T is the absolute temperature in Kelvin. N is the ratio of the two currents.
VDD CPU I NI IBIAS
DN
Figure 34. Measuring Temperature Using an NPN Transistor
ADM1062
DP
Figure 35. Measuring Temperature Using a PNP Transistor
THERM DA REMOTE SENSING TRANSISTOR THERM DC
DP DN BIAS DIODE
VOUT+ TO ADC VOUT

04433-069
LOW-PASS FILTER fC = 65kHz
Figure 36. Signal Conditioning for Remote Diode Temperature Sensors
04433-071
2N3906 PNP
DN
ADM1062
To measure VBE, the sensor is switched between operating currents of I and N I. The resulting waveform is passed through a 65 kHz low-pass filter to remove noise and through a chopperstabilized amplifier that amplifies and rectifies the waveform to produce a dc voltage proportional to VBE. This voltage is measured by the ADC to produce a temperature output in 12-bit offset binary. To further reduce the effects of noise, digital filtering is performed by averaging the results of 16 measurement cycles. A remote temperature measurement takes nominally 600 ms. The results of remote temperature measurements are stored in 12-bit, offset binary format, as shown in Table 11. This format provides temperature readings with a resolution of 0.125C. Table 11. Temperature Data Format
Temperature 128C 125C 100C 75C 50C 25C 10C 0C +10.25C +25.5C +50.75C +75C +100C +125C +128C Digital Output (Hex) 0x400 0x418 0x4E0 0x5A8 0x670 0x738 0x7B0 0x800 0x852 0x8CC 0x996 0xA58 0XB20 0xBE8 0xC00 Digital Output (Binary) 010000000000 010000011000 010011100000 010110101000 011001110000 011100111000 011110110000 100000000000 100001010010 100011001100 100110010110 101001011000 101100100000 101111101000 110000000000
ADM1062 APPLICATIONS DIAGRAM

12V IN 5V IN 3V IN IN 12V OUT 5V OUT 3V OUT
DC-TO-DC1
VH 5V OUT 3V OUT 3.3V OUT 2.5V OUT 1.8V OUT 1.2V OUT 0.9V OUT POWRON RESET VX5 VP1 VP2 VP3 VP4 VX1 VX2 VX3 VX4 EN OUT 3.3V OUT
ADM1062
PDO1 PDO2 IN PDO3 PDO4 PDO5 PDO6 PDO7 PDO8 PDO9 PDO10 PWRGD SIGNAL VALID SYSTEM RESET IN
DC-TO-DC2
EN OUT 2.5V OUT
DC-TO-DC3
EN OUT 3.3V OUT IN 1.8V OUT
REFOUT
DAC1* DP
DN REFIN VCCP VDDCAP GND 3.3V OUT 10F 10F 10F IN *ONLY ONE MARGINING CIRCUIT SHOWN FOR CLARITY. DAC1 TO DAC6 ALLOW MARGINING FOR UP TO SIX VOLTAGE RAILS. TEMPERATURE DIODE 3.3V OUT 2.5V OUT MICROPROCESSOR EN OUT TRIM
LDO
EN OUT 0.9V OUT
1.2V OUT
DC-TO-DC4
Figure 37. Applications Diagram
04433-068
ADM1062 COMMUNICATING WITH THE ADM1062

CONFIGURATION DOWNLOAD AT POWER-UP
The configuration of the ADM1062 (undervoltage/overvoltage thresholds, glitch filter timeouts, PDO configurations, and so on) is dictated by the contents of the RAM. The RAM comprises digital latches that are local to each of the functions on the device. The latches are double-buffered and have two identical latches, Latch A and Latch B. Therefore, when an update to a function occurs, the contents of Latch A are updated first, and then the contents of Latch B are updated with identical data. The advantages of this architecture are explained in detail in the Updating the Configuration section. The two latches are volatile memory and lose their contents at power-down. Therefore, the configuration in the RAM must be restored at power-up by downloading the contents of the EEPROM (nonvolatile memory) to the local latches. This download occurs in six steps, as follows: With no power applied to the device, the PDOs are all high impedance. When 1.2 V appears on any of the inputs connected to the VDD arbitrator (VH or VPx), the PDOs are all weakly pulled to GND with a 20 k resistor. When the supply rises above the undervoltage lockout of the device (UVLO is 2.5 V), the EEPROM starts to download to the RAM. The EEPROM downloads its contents to all Latch As. When the contents of the EEPROM are completely downloaded to the Latch As, the device controller signals all Latch As to download to all Latch Bs simultaneously, completing the configuration download. At 0.5 ms after the configuration download completes, the first state definition is downloaded from the EEPROM into the SE. Note that any attempt to communicate with the device prior to the completion of the download causes the ADM1062 to issue a no acknowledge (NACK). The ADM1062 provides several options that allow the user to update the configuration over the SMBus interface. The following three options are controlled in the UPDCFG register:
Option 1
Update the configuration in real time. The user writes to the RAM across the SMBus, and the configuration is updated immediately.
Option 2
Update the Latch As without updating the Latch Bs. With this method, the configuration of the ADM1062 remains unchanged and continues to operate in the original setup until the instruction is given to update the Latch Bs.
Option 3
Change the EEPROM register contents without changing the RAM contents, and then download the revised EEPROM contents to the RAM registers. With this method, the configuration of the ADM1062 remains unchanged and continues to operate in the original setup until the instruction is given to update the RAM. The instruction to download from the EEPROM in Option 3 is also a useful way to restore the original EEPROM contents if revisions to the configuration are unsatisfactory. For example, if the user needs to alter an overvoltage threshold, the RAM register can be updated, as described in Option 1. However, if the user is not satisfied with the change and wants to revert to the original programmed value, the device controller can issue a command to download the EEPROM contents to the RAM again, as described in Option 3, restoring the ADM1062 to its original configuration. The topology of the ADM1062 makes this type of operation possible. The local, volatile registers (RAM) are all doublebuffered latches. Setting Bit 0 of the UPDCFG register to 1 leaves the double-buffered latches open at all times. If Bit 0 is set to 0 when a RAM write occurs across the SMBus, only the first side of the double-buffered latch is written to. The user must then write a 1 to Bit 1 of the UPDCFG register. This generates a pulse to update all the second latches at once. EEPROM writes occur in a similar way. The final bit in this register can enable or disable EEPROM page erasure. If this bit is set high, the contents of an EEPROM page can all be set to 1. If this bit is set low, the contents of a page cannot be erased, even if the command code for page erasure is programmed across the SMBus. The bit map for the UPDCFG register is shown in the AN-698 Application Note at www.analog.com. A flow diagram for download at power-up and subsequent configuration updates is shown in Figure 38.
UPDATING THE CONFIGURATION

After power-up, with all the configuration settings loaded from the EEPROM into the RAM registers, the user may need to alter the configuration of functions on the ADM1062, such as changing the undervoltage or overvoltage limit of an SFD, changing the fault output of an SFD, or adjusting the rise time delay of one of the PDOs.
ADM1062
SMBus
POWER-UP (VCC > 2.5V)
EEPROM
Figure 38. Configuration Update Flow Diagram
UPDATING THE SEQUENCING ENGINE

Sequencing engine (SE) functions are not updated in the same way as regular configuration latches. The SE has its own dedicated 512-byte nonvolatile, electrically erasable, programmable, readonly memory (EEPROM) for storing state definitions. The EEPROM provides 63 individual states, each with a 64-bit word (one state is reserved). At power-up, the first state is loaded from the SE EEPROM into the engine itself. When the conditions of this state are met, the next state is loaded from the EEPROM into the engine, and so on. The loading of each new state takes approximately 10 s. To alter a state, the required changes must be made directly to the EEPROM. RAM for each state does not exist. The relevant alterations must be made to the 64-bit word, which is then uploaded directly to the EEPROM.
The major differences between the EEPROM and other registers are as follows: An EEPROM location must be blank before it can be written to. If it contains data, the data must first be erased. Writing to the EEPROM is slower than writing to the RAM. Writing to the EEPROM should be restricted because it has a limited write/cycle life of typically 10,000 write operations due to the usual EEPROM wear-out mechanisms.
The first EEPROM is split into 16 (0 to 15) pages of 32 bytes each. Page 0 to Page 6, starting at Address 0xF800, hold the configuration data for the applications on the ADM1062 (such as the SFDs and PDOs). These EEPROM addresses are the same as the RAM register addresses, prefixed by F8. Page 7 is reserved. Page 8 to Page 15 are for customer use. Data can be downloaded from the EEPROM to the RAM in one of the following ways: At power-up, when Page 0 to Page 6 are downloaded By setting Bit 0 of the UDOWNLD register (0xD8), which performs a user download of Page 0 to Page 6
INTERNAL REGISTERS
The ADM1062 contains a large number of data registers. The principal registers are the address pointer register and the configuration registers.
Address Pointer Register

The address pointer register contains the address that selects one of the other internal registers. When writing to the ADM1062, the first byte of data is always a register address that is written to the address pointer register.
SERIAL BUS INTERFACE

The ADM1062 is controlled via the serial system management bus (SMBus) and is connected to this bus as a slave device under the control of a master device. It takes approximately 1 ms after power-up for the ADM1062 to download from its EEPROM. Therefore, access to the ADM1062 is restricted until the download is complete.
Configuration Registers
The configuration registers provide control and configuration for various operating parameters of the ADM1062.
Identifying the ADM1062 on the SMBus

The ADM1062 has a 7-bit serial bus slave address (see Table 12). The device is powered up with a default serial bus address. The five MSBs of the address are set to 00101; the two LSBs are determined by the logical states of Pin A1 and Pin A0. This allows the connection of four ADM1062s to one SMBus. Table 12. Serial Bus Slave Address
A1 Pin Low Low High High
1
EEPROM
The ADM1062 has two 512-byte cells of nonvolatile EEPROM from Register Address 0xF800 to Register Address 0xFBFF. The EEPROM is used for permanent storage of data that is not lost when the ADM1062 is powered down. One EEPROM cell contains the configuration data of the device; the other contains the state definitions for the SE. Although referred to as read-only memory, the EEPROM can be written to, as well as read from, using the serial bus in exactly the same way as the other registers.
A0 Pin Low High Low High
Hex Address 0x28 0x2A 0x2C 0x2E
04433-035
E E P R O M L D
DEVICE CONTROLLER D A T A LATCH A
R A M L D
U P D
LATCH B
FUNCTION (OV THRESHOLD ON VP1)
7-Bit Address 0010100x1 0010101x1 0010110x1 0010111x1
x = Read/Write bit. The address is shown only as the first 7 MSBs.
ADM1062
The device also has several identification registers (read-only) that can be read across the SMBus. Table 13 lists these registers with their values and functions.
Table 13. Identification Register Values and Functions
Name MANID REVID MARK1 MARK2 Address 0xF4 0xF5 0xF6 0xF7 Value 0x41 0x02 0x00 0x00 Function Manufacturer ID for Analog Devices Silicon revision Software brand Software brand
All other devices on the bus remain idle while the selected device waits for data to be read from or written to it. If the R/W bit is a 0, the master writes to the slave device. If the R/W bit is a 1, the master reads from the slave device.
Step 2
Data is sent over the serial bus in sequences of nine clock pulses: eight bits of data followed by an acknowledge bit from the slave device. Data transitions on the data line must occur during the low period of the clock signal and remain stable during the high period because a low-to-high transition when the clock is high could be interpreted as a stop signal. If the operation is a write operation, the first data byte after the slave address is a command byte. This command byte tells the slave device what to expect next. It may be an instruction telling the slave device to expect a block write, or it may be a register address that tells the slave where subsequent data is to be written. Because data can flow in only one direction, as defined by the R/W bit, sending a command to a slave device during a read operation is not possible. Before a read operation, it may be necessary to perform a write operation to tell the slave what sort of read operation to expect and/or the address from which data is to be read.
General SMBus Timing

Figure 39, Figure 40, and Figure 41 are timing diagrams for general read and write operations using the SMBus. The SMBus specification defines specific conditions for different types of read and write operations, which are discussed in the Write Operations and Read Operations sections. The general SMBus protocol operates as follows:
Step 1
The master initiates data transfer by establishing a start condition, defined as a high-to-low transition on the serial data-line SDA, while the serial clock-line SCL remains high. This indicates that a data stream follows. All slave peripherals connected to the serial bus respond to the start condition and shift in the next eight bits, consisting of a 7-bit slave address (MSB first) plus an R/W bit. This bit determines the direction of the data transfer, that is, whether data is written to or read from the slave device (0 = write, 1 = read). The peripheral whose address corresponds to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the acknowledge bit, and by holding it low during the high period of this clock pulse.
1 SCL 0 START BY MASTER FRAME 1 SLAVE ADDRESS SCL (CONTINUED) SDA (CONTINUED) 1 9 0 1 0 1 A1 A0 R/W ACK. BY SLAVE D7 D6 9 1
Step 3
When all data bytes have been read or written, stop conditions are established. In write mode, the master pulls the data line high during the 10th clock pulse to assert a stop condition. In read mode, the master device releases the SDA line during the low period before the ninth clock pulse, but the slave device does not pull it low. This is known as a no acknowledge. The master then takes the data line low during the low period before the 10th clock pulse and then high during the 10th clock pulse to assert a stop condition.
SDA
D5
D4
D3
D2
D1
D0 ACK. BY SLAVE
FRAME 2 COMMAND CODE 1 9
D7
D6
D5
D4
D3
D2
D1
D0 ACK. BY SLAVE
D7
D6
D5
D4
D3
D2
D1
D0
04433-036
FRAME 3 DATA BYTE
FRAME N DATA BYTE
ACK. BY SLAVE
STOP BY MASTER
Figure 39. General SMBus Write Timing Diagram
ADM1062
1 SCL 0 START BY MASTER 1 FRAME 1 SLAVE ADDRESS 0 1 0 1 A1 A0 R/W ACK. BY SLAVE 9 1 FRAME 2 DATA BYTE D7 D6 D5 D4 D3 D2 D1 D0 ACK. BY MASTER 9 9 1 9
SDA
SCL (CONTINUED) SDA (CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0 ACK. BY MASTER
D7
D6
D5
D4
D3
D2
D1
D0 NO ACK.
04433-037
FRAME 3 DATA BYTE
FRAME N DATA BYTE
STOP BY MASTER
Figure 40. General SMBus Read Timing Diagram
tR
SCL
tF
t HD; STA
t LO W t HD; STA t HD; DAT t SU; DAT

04433-038
t HI G H
t SU; STA
t SU; STO
SDA
t BUF
P S S P
Figure 41. Serial Bus Timing Diagram
ADM1062
SMBus PROTOCOLS FOR RAM AND EEPROM
The ADM1062 contains volatile registers (RAM) and nonvolatile registers (EEPROM). User RAM occupies Address 0x00 to Address 0xDF; the EEPROM occupies Address 0xF800 to Address 0xFBFF. Data can be written to and read from both the RAM and the EEPROM as single data bytes. Data can be written only to unprogrammed EEPROM locations. To write new data to a programmed location, the location contents must first be erased. EEPROM erasure cannot be done at the byte level. The EEPROM is arranged as 32 pages of 32 bytes each, and an entire page must be erased. Page erasure is enabled by setting Bit 2 in the UPDCFG register (Address 0x90) to 1. If this bit is not set, page erasure cannot occur, even if the command byte (0xFE) is programmed across the SMBus.
To erase a page of EEPROM memory. EEPROM memory can be written to only if it is unprogrammed. Before writing to one or more EEPROM memory locations that are already programmed, the page(s) containing those locations must first be erased. EEPROM memory is erased by writing a command byte. The master sends a command code telling the slave device to erase the page. The ADM1062 command code for a page erasure is 0xFE (1111 1110). Note that for a page erasure to take place, the page address must be given in the previous write word transaction (see the Write Byte/Word section). In addition, Bit 2 in the UPDCFG register (Address 0x90) must be set to 1.
1 S 2 SLAVE ADDRESS W 3 A 4 COMMAND BYTE (0xFE) 5 A 6 P
04433-040 04433-041
WRITE OPERATIONS
The SMBus specification defines several protocols for different types of read and write operations. The following abbreviations are used in Figure 42 to Figure 50:

Figure 43. EEPROM Page Erasure
S = Start P = Stop R = Read W = Write A = Acknowledge A = No acknowledge
As soon as the ADM1062 receives the command byte, page erasure begins. The master device can send a stop command as soon as it sends the command byte. Page erasure takes approximately 20 ms. If the ADM1062 is accessed before erasure is complete, it responds with a no acknowledge (NACK).
Write Byte/Word
In a write byte/word operation, the master device sends a command byte and one or two data bytes to the slave device, as follows: The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). 3. The addressed slave device asserts an ACK on SDA. 4. The master sends a command code. 5. The slave asserts an ACK on SDA. 6. The master sends a data byte. 7. The slave asserts an ACK on SDA. 8. The master sends a data byte or asserts a stop condition. 9. The slave asserts an ACK on SDA. 10. The master asserts a stop condition on SDA to end the transaction. 1. 2. In the ADM1062, the write byte/word protocol is used for three purposes:
The ADM1062 uses the following SMBus write protocols.
Send Byte
In a send byte operation, the master device sends a single command byte to a slave device, as follows: 1. 2. 3. 4. 5. 6. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). The addressed slave device asserts an acknowledge (ACK) on SDA. The master sends a command code. The slave asserts an ACK on SDA. The master asserts a stop condition on SDA, and the transaction ends.
In the ADM1062, the send byte protocol is used for two purposes:
To write a register address to the RAM for a subsequent single byte read from the same address, or for a block read or a block write starting at that address, as shown in Figure 42.
1 S 2 SLAVE ADDRESS W 3 A 4 RAM ADDRESS (0x00 TO 0xDF) 5 A 6
04433-039
To write a single byte of data to the RAM. In this case, the command byte is RAM Address 0x00 to RAM Address 0xDF, and the only data byte is the actual data, as shown in Figure 44.
1 2 3 4 5 6 7 8
Figure 42. Setting a RAM Address for Subsequent Read
RAM SLAVE S ADDRESS W A ADDRESS A DATA A P (0x00 TO 0xDF)
Figure 44. Single Byte Write to the RAM
ADM1062
To set up a 2-byte EEPROM address for a subsequent read, write, block read, block write, or page erase. In this case, the command byte is the high byte of EEPROM Address 0xF8 to EEPROM Address 0xFB. The only data byte is the low byte of the EEPROM address, as shown in Figure 45.
1 2 3 4 5 6 7 8
04433-042
7. 8. 9. 10.
1 S
The slave asserts an ACK on SDA. The master sends N data bytes. The slave asserts an ACK on SDA after each data byte. The master asserts a stop condition on SDA to end the transaction.
2 3 4 5 6 7 8 9 10
04433-044
EEPROM EEPROM SLAVE ADDRESS ADDRESS S ADDRESS W A A A P HIGH BYTE LOW BYTE (0xF8 TO 0xFB) (0x00 TO 0xFF)
SLAVE W A COMMAND 0xFC A BYTE A DATA A DATA A DATA A P ADDRESS (BLOCK WRITE) COUNT 1 2 N
Figure 45. Setting an EEPROM Address
Figure 47. Block Write to the EEPROM or RAM
Because a page consists of 32 bytes, only the three MSBs of the address low byte are important for page erasure. The lower five bits of the EEPROM address low byte specify the addresses within a page and are ignored during an erase operation. To write a single byte of data to the EEPROM. In this case, the command byte is the high byte of EEPROM Address 0xF8 to EEPROM Address 0xFB. The first data byte is the low byte of the EEPROM address, and the second data byte is the actual data, as shown in Figure 46.
1 2 3 4 5 6 7 8 9 10
04433-043
Unlike some EEPROM devices that limit block writes to within a page boundary, there is no limitation on the start address when performing a block write to EEPROM, except when
There must be at least N locations from the start address to the highest EEPROM address (0xFBFF) to avoid writing to invalid addresses. An address crosses a page boundary. In this case, both pages must be erased before programming.
EEPROM EEPROM SLAVE ADDRESS ADDRESS P S ADDRESS W A A HIGH BYTE LOW BYTE A DATA A (0xF8 TO 0xFB) (0x00 TO 0xFF)
Note that the ADM1062 features a clock extend function for writes to EEPROM. Programming an EEPROM byte takes approximately 250 s, which limits the SMBus clock for repeated or block write operations. The ADM1062 pulls SCL low and extends the clock pulse when it cannot accept any more data.
Figure 46. Single Byte Write to the EEPROM
READ OPERATIONS
The ADM1062 uses the following SMBus read protocols.
Block Write
In a block write operation, the master device writes a block of data to a slave device. The start address for a block write must have been set previously. In the ADM1062, a send byte operation sets a RAM address, and a write byte/word operation sets an EEPROM address, as follows: 1. 2. 3. 4. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). The addressed slave device asserts an ACK on SDA. The master sends a command code that tells the slave device to expect a block write. The ADM1062 command code for a block write is 0xFC (1111 1100). The slave asserts an ACK on SDA. The master sends a data byte that tells the slave device how many data bytes are being sent. The SMBus specification allows a maximum of 32 data bytes in a block write.
Receive Byte
In a receive byte operation, the master device receives a single byte from a slave device, as follows: 1. 2. 3. 4. 5. 6. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the read bit (high). The addressed slave device asserts an ACK on SDA. The master receives a data byte. The master asserts a NACK on SDA. The master asserts a stop condition on SDA, and the transaction ends.
5. 6.
In the ADM1062, the receive byte protocol is used to read a single byte of data from a RAM or EEPROM location whose address has previously been set by a send byte or write byte/word operation, as shown in Figure 48.
1 S 2 SLAVE ADDRESS R 3 A 4 DATA 5 A 6 P
04433-045
Figure 48. Single Byte Read from the EEPROM or RAM
ADM1062
Block Read
In a block read operation, the master device reads a block of data from a slave device. The start address for a block read must have been set previously. In the ADM1062, this is done by a send byte operation to set a RAM address, or a write byte/word operation to set an EEPROM address. The block read operation itself consists of a send byte operation that sends a block read command to the slave, immediately followed by a repeated start and a read operation that reads out multiple data bytes, as follows: 1. 2. 3. 4. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). The addressed slave device asserts an ACK on SDA. The master sends a command code that tells the slave device to expect a block read. The ADM1062 command code for a block read is 0xFD (1111 1101). The slave asserts an ACK on SDA. The master asserts a repeat start condition on SDA. The master sends the 7-bit slave address followed by the read bit (high). The slave asserts an ACK on SDA. The ADM1062 sends a byte-count data byte that tells the master how many data bytes to expect. The ADM1062 always returns 32 data bytes (0x20), which is the maximum allowed by the SMBus Version 1.1 specification. The master asserts an ACK on SDA. The master receives 32 data bytes. The master asserts an ACK on SDA after each data byte. The master asserts a stop condition on SDA to end the transaction.
2 3 4 5 6 7 8 9 10 11 12
Error Correction
The ADM1062 provides the option of issuing a packet error correction (PEC) byte after a write to the RAM, a write to the EEPROM, a block write to the RAM/EEPROM, or a block read from the RAM/ EEPROM. This option enables the user to verify that the data received by or sent from the ADM1062 is correct. The PEC byte is an optional byte sent after the last data byte has been written to or read from the ADM1062. The protocol is the same as a block read for Step 1 to Step 12 and then proceeds as follows: 13. The ADM1062 issues a PEC byte to the master. The master checks the PEC byte and issues another block read if the PEC byte is incorrect. 14. A NACK is generated after the PEC byte to signal the end of the read. 15. The master asserts a stop condition on SDA to end the transaction. Note that the PEC byte is calculated using CRC-8. The frame check sequence (FCS) conforms to CRC-8 by the polynomial C(x) = x8 + x2 + x1 + 1 See the SMBus Version 1.1 specification for details. An example of a block read with the optional PEC byte is shown in Figure 50.
1 2 3 4 5 6 7 8 9 10 11 12 SLAVE SLAVE BYTE DATA COMMAND 0xFD A S ADDRESS W A (BLOCK READ) A S ADDRESS R A COUNT A 1
5. 6. 7. 8. 9.
10. 11. 12. 13.

1 S
13 14 15 A PEC A P
04433-047
DATA 32
SLAVE COMMAND 0xFD SLAVE BYTE DATA W A A S R A A A ADDRESS (BLOCK READ) ADDRESS COUNT 1
Figure 50. Block Read from the EEPROM or RAM with PEC
13 P
04433-046
DATA A 32
Figure 49. Block Read from the EEPROM or RAM
ADM1062 OUTLINE DIMENSIONS

6.00 BSC SQ 0.60 MAX 0.60 MAX
31 30 40 1
PIN 1 INDICATOR
PIN 1 INDICATOR
TOP VIEW
5.75 BCS SQ
0.50 BSC 0.50 0.40 0.30
EXPOSED PAD
(BOTTOM VIEW)
4.25 4.10 SQ 3.95

10 11
21 20
0.25 MIN 4.50 REF
12 MAX
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM
1.00 0.85 0.80
SEATING PLANE
0.30 0.23 0.18
0.20 REF
COPLANARITY 0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
Figure 51. 40-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 6 mm 6 mm Body, Very Thin Quad (CP-40-1) Dimensions shown in millimeters
0.75 0.60 0.45
1.20 MAX
48 1
9.00 BSC SQ
37 36 PIN 1
1.05 1.00 0.95
0 MIN
0.15 0.05
SEATING PLANE
0.20 0.09 7 3.5 0 0.08 MAX COPLANARITY
TOP VIEW
(PINS DOWN)
7.00 BSC SQ
12 13
25 24
VIEW A
ROTATED 90 CCW
COMPLIANT TO JEDEC STANDARDS MS-026ABC
VIEW A
0.50 0.27 BSC 0.22 LEAD PITCH 0.17
Figure 52. 48-Lead Thin Plastic Quad Flat Package [TQFP] (SU-48) Dimensions shown in millimeters
ADM1062
ORDERING GUIDE
Model ADM1062ACP ADM1062ACP-REEL7 ADM1062ACPZ 1 ADM1062ACPZ-REEL71 ADM1062ASU ADM1062ASU-REEL7 ADM1062ASUZ1 ADM1062ASUZ-REEL71 EVAL-ADM1062LFEBZ1 EVAL-ADM1062TQEBZ1
1
Temperature Range 40C to +85C 40C to +85C 40C to +85C 40C to +85C 40C to +85C 40C to +85C 40C to +85C 40C to +85C
Package Description 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 48-Lead TQFP 48-Lead TQFP 48-Lead TQFP 48-Lead TQFP Evaluation Kit (LFCSP Version) Evaluation Kit (TQFP Version)
Package Option CP-40-1 CP-40-1 CP-40-1 CP-40-1 SU-48 SU-48 SU-48 SU-48
Z = RoHS Compliant Part.
ADM1062 NOTES
ADM1062 NOTES
20052008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04433-0-5/08(B)

Super Sequencer With Margining Control and Temperature Monitoring ADM1062

Uploaded by

Copyright:

Available Formats

Super Sequencer With Margining Control and Temperature Monitoring ADM1062

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Super Sequencer With Margining Control and Temperature Monitoring ADM1062

Uploaded by

Copyright:

Available Formats

Super Sequencer with Margining Control and Temperature Monitoring ADM1062

FUNCTIONAL BLOCK DIAGRAM

12-BIT SAR ADC

CONFIGURABLE OUTPUT DRIVERS (HV CAPABLE OF DRIVING GATES OF N-FET)

PDO1 PDO2 PDO3 PDO4 PDO5 PDO6

DAC1 DAC2 DAC3 DAC4 DAC5 DAC6

ADM1062 TABLE OF CONTENTS

DETAILED BLOCK DIAGRAM

12-BIT SAR ADC

CONFIGURABLE OUTPUT DRIVER (HV)

PDO1 PDO2 PDO3 PDO4 PDO5

CONFIGURABLE OUTPUT DRIVER (HV)

VP1 VP2 VP3 VP4 VH

CONFIGURABLE OUTPUT DRIVER (LV)

PDO7 PDO8 PDO9

CONFIGURABLE OUTPUT DRIVER (LV)

Midrange and high range

Low range and midrange

No input attenuation error

2.048 12 2.5 0.05

Endpoint corrected, VREFIN = 2.048 V VREFIN = 2.048 V

Same range, independent of center point Endpoint corrected

IOH = 0 A IOH = 1 A 2 V < VOH < 7 V

2.4 4.5 VPU 0.3 0

ADM1062 ABSOLUTE MAXIMUM RATINGS

ADM1062 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

VX1 1 VX2 2 VX3 3 VX4 4 VX5 5 VP1 6 VP2 7 VP3 8 VP4 9 VH 10

NC 1 VX1 2 VX2 3 VX3 4 VX4 5 VX5 6 VP1 7 VP2 8 VP3 9 VP4 10 VH 11 NC 12

Figure 3. LFCSP Pin Configuration

Figure 4. TQFP Pin Configuration

Table 4. Pin Function Descriptions

VX1 to VX5 (VXx) VP1 to VP4 (VPx)

ADM1062 TYPICAL PERFORMANCE CHARACTERISTICS

Figure 5. VVDDCAP vs. VVP1

Figure 8. IVP1 vs. VVP1 (VP1 Not as Supply)

4.0 3.5 3.0

2.5 2.0 1.5 1.0 0.5 0 0 2 4 6 8 VVH (V) 10 12 14 16

Figure 6. VVDDCAP vs. VVH

Figure 9. IVH vs. VVH (VH as Supply)

5.0 4.5 4.0 3.5

350 300 250 200 150 100 50 0

3.0 2.5 2.0 1.5 1.0 0.5 0 0 1 2 3 VVP1 (V) 4 5 6

Figure 7. IVP1 vs. VVP1 (VP1 as Supply)

Figure 10. IVH vs. VVH (VH Not as Supply)

0.2 0 0.2 0.4 0.6

0.8 1.0 0 1000 2000 CODE 3000 4000

7.5 ILOAD (A)

Figure 11. Charge-Pumped VPDO1 (FET Drive Mode) vs. ILOAD

Figure 14. DNL for ADC

5.0 4.5 4.0 3.5

3.0 VP1 = 5V 2.5 2.0 1.5 1.0 0.5 0 0 1 2 3 ILOAD (mA) 4 5 6

Figure 12. VPDO1 (Strong Pull-Up to VPx) vs. ILOAD

Figure 15. INL for ADC

12000 9894 10000

3.5 3.0 VPDO1 (V) 2.5 2.0 1.5 1.0

VP1 = 5V HITS PER CODE

25 0 2047 2048 CODE

Figure 13. VPDO1 (Weak Pull-Up to VPx) vs. ILOAD

Figure 16. ADC Noise, Midcode Input, 10,000 Reads