Tda8950 1902105

TDA8950
2 × 150 W class-D power amplifier

Rev. 02 — 11 June 2009 Product data sheet
1. General description
The TDA8950 is a high-efficiency Class D audio power amplifier. The typical output power
is 2 × 150 W with a speaker load impedance of 4 Ω.
The TDA8950 is available in both HSOP24 and DBS23P power packages. The amplifier
operates over a wide supply voltage range from ±12.5 V to ±40 V and features low
quiescent current consumption.
2. Features
n Pin compatible with TDA8920B for both HSOP24 and DBS23P packages
n Symmetrical operating supply voltage range from ±12.5 V to ±40 V
n Stereo full differential inputs, can be used as stereo Single-Ended (SE) or mono
Bridge-Tied Load (BTL) amplifier
n High output power in typical applications:
u SE 2 × 150 W, RL = 4 Ω (VP = ±37 V)
u SE 2 × 170 W, RL = 4 Ω (VP = ±39 V)
u SE 2 × 100 W, RL = 6 Ω (VP = ±37 V)
u BTL 1 × 300 W, RL = 8 Ω (VP = ±37 V)
n Low noise
n Smooth pop noise-free start-up and switch off
n Zero dead time switching
n Fixed frequency
n Internal or external clock
n High efficiency
n Low quiescent current
n Advanced protection strategy: voltage protection and output current limiting
n Thermal FoldBack (TFB)
n Fixed gain of 30 dB in SE and 36 dB in BTL applications
n Fully short-circuit proof across load
n BD modulation in BTL configuration
3. Applications
n DVD
n Mini and micro receiver
n Home Theater In A Box (HTIAB) system
n High-power speaker system
NXP Semiconductors TDA8950
4. Quick reference data

Table 1. Quick reference data
Symbol Parameter Conditions Min Typ Max Unit
General, VP[1] = ±30 V
VP supply voltage Operating mode [2] ±12.5 ±35 ±40 V
VP(ovp) overvoltage protection supply voltage Standby, Mute modes; VDD − VSS 85 - 90 V
Iq(tot) total quiescent current Operating mode; no load; no filter; no - 50 75 mA
RC-snubber network connected
Stereo SE configuration
Po output power Tj = 85 °C; LLC = 22 µH; CLC = 680 nF [3]
(see Figure 10)

THD + N = 10 %; RL = 4 Ω; VP = ±39 V 170 W
THD + N = 0.5 %; RL = 4 Ω; VP = ±37 V - 100 - W
THD + N = 10 %; RL = 4 Ω; VP = ±37 V - 150 - W
THD + N = 10 %; RL = 6 Ω; VP = ±37 V - 100 - W
Mono BTL configuration
Po output power Tj = 85 °C; LLC = 22 µH; CLC = 680 nF [3] - 300 - W
(see Figure 10); RL = 8 Ω;
THD + N = 10 %; VP = ±37 V
[1] VP is the supply voltage on pins VDDP1, VDDP2 and VDDA.

[2] The circuit is DC adjusted at VP = ±12.5 V to ±32.5 V.
[3] Output power is measured indirectly; based on RDSon measurement; see Section 13.3.
5. Ordering information
Table 2. Ordering information
Type number Package
Name Description Version
TDA8950J DBS23P plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1
TDA8950TH HSOP24 plastic, heatsink small outline package; 24 leads; low stand-off height SOT566-3
TDA8950_2 © NXP B.V. 2009. All rights reserved.
Product data sheet Rev. 02 — 11 June 2009 2 of 39

6. Block diagram
VDDA n.c. STABI PROT VDDP2 VDDP1
3 (20) 10 (4) 18 (12) 13 (7) 23 (16) 14 (8)

15 (9)
BOOT1
9 (3)
IN1M DRIVER
INPUT PWM
SWITCH1 HIGH
8 (2) STAGE MODULATOR CONTROL 16 (10)
IN1P AND OUT1
HANDSHAKE
DRIVER
mute
11 (5) LOW
n.c.
STABI
VSSP1
7 (1)
OSC
TEMPERATURE SENSOR TDA8950TH
6 (23) OSCILLATOR MANAGER (TDA8950J) VDDP2
CURRENT PROTECTION
MODE MODE
VOLTAGE PROTECTION
22 (15)
BOOT2
2 (19)
SGND
mute DRIVER
CONTROL HIGH
5 (22) SWITCH2 21 (14)
AND OUT2
IN2P
INPUT PWM HANDSHAKE
DRIVER
4 (21) STAGE MODULATOR
IN2M LOW
1 (18) 12 (6) 24 (17) 19 (-) 17 (11) 20 (13) 001aah653
VSSA n.c. VSSD n.c. VSSP1 VSSP2
Pin numbers in brackets refer to type number TDA8950J.

Fig 1. Block diagram

7. Pinning information
7.1 Pinning
OSC 1
IN1P 2
IN1M 3
n.c. 4
n.c. 5
n.c. 6
PROT 7
VDDP1 8
BOOT1 9
OUT1 10
VSSP1 11
VSSD 24 1 VSSA STABI 12 TDA8950J
VDDP2 23 2 SGND VSSP2 13
BOOT2 22 3 VDDA OUT2 14
OUT2 21 4 IN2M BOOT2 15
VSSP2 20 5 IN2P VDDP2 16
n.c. 19 6 MODE VSSD 17
TDA8950TH
STABI 18 7 OSC VSSA 18
VSSP1 17 8 IN1P SGND 19
OUT1 16 9 IN1M VDDA 20
BOOT1 15 10 n.c. IN2M 21
VDDP1 14 11 n.c. IN2P 22
PROT 13 12 n.c. MODE 23
001aah654 001aah655
Fig 2. Pin configuration TDA8950TH Fig 3. Pin configuration TDA8950J

7.2 Pin description

Table 3. Pin description
Symbol Pin Description
TDA8950TH TDA8950J
VSSA 1 18 negative analog supply voltage
SGND 2 19 signal ground
VDDA 3 20 positive analog supply voltage
IN2M 4 21 channel 2 negative audio input
IN2P 5 22 channel 2 positive audio input
MODE 6 23 mode selection input: Standby, Mute or Operating
mode
OSC 7 1 oscillator frequency adjustment or tracking input
IN1P 8 2 channel 1 positive audio input
IN1M 9 3 channel 1 negative audio input
n.c. 10 4 not connected
PROT 13 7 decoupling capacitor for protection (OCP)
VDDP1 14 8 channel 1 positive power supply voltage
BOOT1 15 9 channel 1 bootstrap capacitor
OUT1 16 10 channel 1 PWM output
VSSP1 17 11 channel 1 negative power supply voltage
STABI 18 12 decoupling of internal stabilizer for logic supply
n.c. 19 - not connected
VSSP2 20 13 channel 2 negative power supply voltage
OUT2 21 14 channel 2 PWM output
BOOT2 22 15 channel 2 bootstrap capacitor
VDDP2 23 16 channel 2 positive power supply voltage
VSSD 24 17 negative digital supply voltage
8. Functional description
8.1 General
The TDA8950 is a two-channel audio power amplifier that uses Class D technology.
For each channel, the audio input signal is converted into a digital PWM signal using an
analog input stage and a PWM modulator; see Figure 1. To drive the output power
transistors, the digital PWM signal is fed to a control and handshake block and to high-
and low-side driver circuits. This level-shifts the low-power digital PWM signal from a logic
level to a high-power PWM signal switching between the main supply lines.
A 2nd-order low-pass filter converts the PWM signal to an analog audio signal that can be
used to drive a loudspeaker.

The TDA8950 single-chip Class D amplifier contains high-power switches, drivers, timing
and handshaking between the power switches, along with some control logic. To ensure
maximum system robustness, an advanced protection strategy has been implemented to
provide overvoltage, overtemperature and overcurrent protection.
Each of the two audio channels contains a PWM modulator, an analog feedback loop and
a differential input stage. The TDA8950 also contains circuits common to both channels
such as the oscillator, all reference sources, the mode interface and a digital timing
manager.
The two independent amplifier channels feature high output power, high efficiency, low
distortion and low quiescent currents, and can be connected in the following
configurations:
• Stereo Single-Ended (SE)
• Mono Bridge-Tied Load (BTL)
The amplifier system can be switched to one of three operating modes using pin MODE:
• Standby mode: featuring very low quiescent current

• Mute mode: the amplifier is operational but the audio signal at the output is
suppressed by disabling the voltage-to-current (VI converter) input stages
• Operating mode: the amplifier is fully operational, de-muted and can deliver an output
signal
A slowly rising voltage should be applied (e.g. via an RC network) to pin MODE to ensure
pop noise-free start-up. The bias-current setting of the (VI converter) input stages is
related to the voltage on the MODE pin.
In Mute mode, the bias-current setting of the VI converters is zero (VI converters are
disabled). In Operating mode, the bias current is at a maximum. The time constant
required to apply the DC output offset voltage gradually between Mute and Operating
mode levels can be generated using an RC network connected to pin MODE. An example
of a switching circuit for driving pin MODE is illustrated in Figure 4. If the capacitor was
omitted, the very short switching time constant could result in audible pop noises being
generated at start-up (depending on the DC output offset voltage and loudspeaker used).
+5 V
5.6 kΩ
470 Ω
mode control
5.6 kΩ
10 µF
mute/ S1 standby/ S2
operating operating
SGND
010aaa552
Fig 4. Example of mode selection circuit

To ensure the coupling capacitors at the inputs (CIN in Figure 10) are fully charged before
the outputs start switching, a delay is inserted during the transition from Mute to Operating
mode. An overview of the start-up timing is provided in Figure 5. For proper switch-off, the
MODE pin should be forced LOW at leaxt 100 ms before the supply lines (VDDA and VSSA)
drop below 12.5 V.
audio output
(1)
modulated PWM
VMODE
50 %
duty cycle
operating
> 4.2 V
mute
2.2 V < VMODE < 3 V
standby
0 V (SGND)
100 ms > 350 ms time
50 ms
audio output
(1)
modulated PWM
VMODE
50 %
duty cycle
operating
> 4.2 V
mute
2.2 V < VMODE < 3 V
standby
0 V (SGND)
100 ms > 350 ms time
50 ms 001aah657
(1) First 1⁄4 pulse down.

Upper diagram: When switching from Standby to Mute, there is a delay of approximately 100 ms
before the output starts switching. The audio signal will become available once VMODE reaches the
Operating mode level (see Table 8), but not earlier than 150 ms after switching to Mute. To start-up
pop noise-free, it is recommended that the time constant applied to pin MODE be at least 350 ms
for the transition between Mute and Operating modes.
Lower diagram: When switching directly from Standby to Operating mode, there is a delay of
100 ms before the outputs start switching. The audio signal becomes available after a second
delay of 50 ms. To start-up pop noise-free, it is recommended that the time-constant applied to pin
MODE be at least 500 ms for the transition between Standby and Operating modes.
Fig 5. Timing on mode selection input pin MODE

8.2 Pulse-width modulation frequency

The amplifier output signal is a PWM signal with a typical carrier frequency of between
250 kHz and 450 kHz. A 2nd-order LC demodulation filter on the output is used to convert
the PWM signal into an analog audio signal. The carrier frequency is determined by an
external resistor, ROSC, connected between pins OSC and VSSA. The optimal carrier
frequency setting is between 250 kHz and 450 kHz.
The carrier frequency is set to 345 kHz by connecting an external 30 kΩ resistor between
pins OSC and VSSA. See Table 9 for more details.
If two or more Class D amplifiers are used in the same audio application, it is
recommended that an external clock circuit be used with all devices (see Section 13.4).
This will ensure that they operate at the same switching frequency, thus avoiding beat
tones (if the switching frequencies are different, audible interference known as ‘beat tones’
can be generated)
8.3 Protection
The following protection circuits are incorporated into the TDA8950:
• Thermal protection:
– Thermal FoldBack (TFB)
– OverTemperature Protection (OTP)
• OverCurrent Protection (OCP)
• Window Protection (WP)
• Supply voltage protection:
– UnderVoltage Protection (UVP)
– OverVoltage Protection (OVP)
– UnBalance Protection (UBP)
How the device reacts to a fault conditions depends on which protection circuit has been
activated.
8.3.1 Thermal protection

The TDA8950 employes an advanced thermal protection strategy. A TFB function
gradually reduces the output power within a defined temperature range. If the temperature
continues to rise, OTP is activated to shut down the device completely.
8.3.1.1 Thermal FoldBack (TFB)

If the junction temperature (Tj) exceeds the thermal foldback activation threshold, the gain
is gradually reduced. This reduces the output signal amplitude and the power dissipation,
eventually stabilizing the temperature.
TFB is specified at the thermal foldback activation temperature Tact(th_fold) where the
closed-loop voltage gain is reduced by 6 dB. The TFB range is:
Tact(th_fold) − 5 °C < Tact(th_fold) < Tact(th_prot)
The value of Tact(th_fold) for the TDA8950 is approximately 153 °C; see Table 8 for more
details.

8.3.1.2 OverTemperature Protection (OTP)

If TFB fails to stabilize the temperature and the junction temperature continues to rise, the
amplifier will shut down as soon as the temperature reaches the thermal protection
activation threshold, Tact(th_prot). The amplifier will resume switching approximately 100 ms
after the temperature drops below Tact(th_prot).
The thermal behavior is illustrated in Figure 6.
Gain
(dB)
30 dB
24 dB
0 dB
(Tact(th_fold) − 5°C) Tact(th_prot) Tj (°C)
Tact(th_fold)
1 2 3
001aah656
(1) Duty cycle of PWM output modulated according to the audio input signal.
(2) Duty cycle of PWM output reduced due to TFB.
(3) Amplifier is switched off due to OTP.
Fig 6. Behavior of TFB and OTP
8.3.2 OverCurrent Protection (OCP)

In order to guarantee the robustness of the TDA8950, the maximum output current that
can be delivered at the output stages is limited. OCP is built in for each output power
switch.
OCP is activated when the current in one of the power transistors exceeds the OCP
threshold (IORM = 9.2 A) due, for example, to a short-circuit to a supply line or across the
load.
The TDA8950 amplifier distinguishes between low-ohmic short-circuit conditions and

other overcurrent conditions such as a dynamic impedance drop at the loudspeaker. The
impedance threshold (Zth) depends on the supply voltage.
How the amplifier reacts to a short circuit depends on the short-circuit impedance:
• Short-circuit impedance > Zth: the amplifier limits the maximum output current to IORM
but the amplifier does not shut down the PWM outputs. Effectively, this results in a
clipped output signal across the load (behavior very similar to voltage clipping).
• Short-circuit impedance < Zth: the amplifier limits the maximum output current to IORM
and at the same time discharges the capacitor on pin PROT. When CPROT is fully
discharged, the amplifier shuts down completely and an internal timer is started.
The value of the protection capacitor (CPROT) connected to pin PROT can be between
10 pF and 220 pF (typically 47 pF). While OCP is activated, an internal current source is
enabled that will discharge CPROT.

When OCP is activated, the power transistors are turned off. They are turned on again
during the next switching cycle. If the output current is still greater than the OCP threshold,
they will be immediately switched off again. This switching will continue until CPROT is fully
discharged. The amplifier will then be switched off completely and a restart sequence
initiated.
After a fixed period of 100 ms, the amplifier will attempt to switch on again, but will fail if
the output current still exceeds the OCP threshold. The amplifier will continue trying to
switch on every 100 ms. The average power dissipation will be low in this situation
because the duty cycle is low.
Switching the amplifier on and off in this way will generate unwanted ‘audio holes’. This
can be avoided by increasing the value of CPROT (up to 220 pF) to delay amplifier
switch-off. CPROT will also prevent the amplifier switching off due to transient
frequency-dependent impedance drops at the speakers.
The amplifier will switch on, and remain in Operating mode, once the overcurrent
condition has been removed. OCP ensures the TDA8950 amplifier is fully protected
against short-circuit conditions while avoiding audio holes.
Table 4. Current limiting behavior during low output impedance conditions at different
values of CPROT
Type VP[1] (V) VI (mV, p-p) f (Hz) CPROT PWM output stops
(pF) Short Short Short
(Zth = 0 Ω) (Zth = 0.5 Ω) (Zth = 1 Ω)
TDA8950 29.5 500 20 10 yes yes OVP[2]
1000 10 yes yes no
20 15 yes yes OVP[2]
1000 15 yes no no
1000 220 no no no

[2] OVP can be triggered by supply pumping; see Section 13.6.
8.3.3 Window Protection (WP)

Window Protection (WP) checks the conditions at the output terminals of the power stage
and is activated:
• During the start-up sequence, when the TDA8950 is switching from Standby to Mute.
Start-up will be interrupted If a short-circuit is detected between one of the output
terminals and pin VDDP1/VDDP2 or VSSP1/VSSP2. The TDA8950 will wait until the
short-circuit to the supply lines has been removed before resuming start-up. The short
circuit will not generate large currents because the short-circuit check is carried out
before the power stages are enabled.
• When the amplifier is shut down completely because the OCP circuit has detected a
short circuit to one of the supply lines.
WP will be activated when the amplifier attempts to restart after 100 ms (see
Section 8.3.2). The amplifier will not start-up again until the short circuit to the supply
lines has been removed.

8.3.4 Supply voltage protection

If the supply voltage drops below the minimum supply voltage threshold, VP(uvp), the UVP
circuit will be activated and the system will shut down. Once the supply voltage rises
above VP(uvp) again, the system will restart after a delay of 100 ms.
If the supply voltage exceeds the maximum supply voltage threshold, VP(ovp), the OVP
circuit will be activated and the power stages will be shut down. When the supply voltage
drops below VP(ovp) again, the system will restart after a delay of 100 ms.
An additional UnBalance Protection (UBP) circuit compares the positive analog supply
voltage (on pin VDDA) with the negative analog supply voltage (on pin VSSA) and is
triggered if the voltage difference exceeds a factor of two (VDDA > 2 × |VSSA| OR |VSSA| >
2 × VDDA). When the supply voltage difference drops below the unbalance threshold,
VP(ubp), the system restarts after 100 ms.
An overview of all protection circuits and their respective effects on the output signal is
provided in Table 5.
Table 5. Overview of TDA8950 protection circuits

Protection name Complete Restart directly Restart after Pin PROT
shutdown 100 ms detection
TFB[1] N N N N
OTP Y N Y N
OCP Y[2] N[2] Y[2] Y
WP N[3] Y N N
UVP Y N Y N
OVP Y N Y N
UBP Y N Y N
[1] Amplifier gain depends on the junction temperature and heatsink size.
[2] The amplifier shuts down completely only if the short-circuit impedance is below the impedance threshold
(Zth; see Section 8.3.2). In all other cases, current limiting results in a clipped output signal.
[3] Fault condition detected during any Standby-to-Mute transition or during a restart after OCP has been
activated (short-circuit to one of the supply lines).
8.4 Differential audio inputs

The audio inputs are fully differential ensuring a high common mode rejection ratio and
maximum flexibility in the application.
• Stereo operation: to avoid acoustical phase differences, the inputs should be in

antiphase and the speakers should be connected in antiphase. This configuration:
– minimizes power supply peak current
– minimizes supply pumping effects, especially at low audio frequencies
• Mono BTL operation: the inputs must be connected in anti-parallel. The output of one
channel is inverted and the speaker load is connected between the two outputs of the
TDA8950. In practice (because of the OCP threshold) the output power can be
boosted to twice the output power that can be achieved with the single-ended
configuration.
The input configuration for a mono BTL application is illustrated in Figure 7.

OUT1
IN1P
IN1M
Vin SGND
IN2P
IN2M OUT2
power stage
mbl466
Fig 7. Input configuration for mono BTL application
9. Limiting values
Table 6. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol Parameter Conditions Min Max Unit
VP[1] supply voltage Standby, Mute modes; VDD − VSS - 90 V
IORM repetitive peak output current maximum output current limiting 9.2 - A
Tstg storage temperature −55 +150 °C

Tamb ambient temperature −40 +85 °C
Tj junction temperature - 150 °C
VMODE voltage on pin MODE referenced to SGND 0 6 V
VOSC voltage on pin OSC 0 SGND + 6 V
VI input voltage referenced to SGND; pin IN1P; IN1M; −5 +5 V
IN2P and IN2M
VPROT voltage on pin PROT referenced to voltage on pin VSSD 0 12 V
VESD electrostatic discharge voltage Human Body Model (HBM) −2000 +2000 V
Charged Device Model (CDM) −500 +500 V
Iq(tot) total quiescent current Operating mode; no load; no filter; no - 75 mA
RC-snubber network connected
VPWM(p-p) peak-to-peak PWM voltage on pins OUT1 and OUT2 - 120 V
10. Thermal characteristics

Table 7. Thermal characteristics
Symbol Parameter Conditions Typ Unit
Rth(j-a) thermal resistance from junction to ambient in free air 40 K/W
Rth(j-c) thermal resistance from junction to case 1.1 K/W

11. Static characteristics

Table 8. Static characteristics
VP = ±35 V; fosc = 345 kHz; Tamb = 25 °C; unless otherwise specified.
Supply
VP[1] supply voltage Operating mode [2] ±12.5 ±30 ±40 V
VP(ovp) overvoltage protection supply voltage Standby, Mute modes; 85 - 90 V
VDD − VSS
VP(uvp) undervoltage protection supply voltage VDD − VSS 20 - 25 V
VP(ubp) unbalance protection supply voltage [3] - 33 - %
Iq(tot) total quiescent current Operating mode; no load; no - 50 75 mA
filter; no RC-snubber network
connected
Istb standby current measured at 30 V - 480 650 µA
Mode select input; pin MODE
VMODE voltage on pin MODE referenced to SGND [4] 0 - 6 V
Standby mode [4][5] 0 - 0.8 V
Mute mode [4][5] 2.2 - 3.0 V
Operating mode [4][5] 4.2 - 6 V
II input current VI = 5.5 V - 110 150 µA
Audio inputs; pins IN1M, IN1P, IN2P and IN2M
VI input voltage DC input [4] - 0 - V
Amplifier outputs; pins OUT1 and OUT2
VO(offset) output offset voltage SE; Mute mode - - ±25 mV
SE; Operating mode [6] - - ±150 mV
BTL; Mute mode - - ±30 mV
BTL; Operating mode [6] - - ±210 mV
Stabilizer output; pin STABI
VO(STABI) output voltage on pin STABI Mute and Operating modes; 9.3 9.8 10.3 V
with respect to VSSD
Temperature protection
Tact(th_prot) thermal protection activation - 154 - °C
temperature
Tact(th_fold) thermal foldback activation closed loop SE voltage gain [7] - 153 - °C
temperature reduced with 6 dB

[2] The circuit is DC adjusted at VP = ±12.5 V to ±42.5 V.
[3] Unbalance protection activated when VDDA > 2 × |VSSA| OR |VSSA| > 2 × VDDA.
[4] With respect to SGND (0 V).
[5] The transition between Standby and Mute modes has hysteresis, while the slope of the transition between Mute and Operating modes is
determined by the time-constant of the RC network on pin MODE; see Figure 8.
[6] DC output offset voltage is gradually applied to the output during the transition between Mute and Operating modes. The slope caused
by any DC output offset is determined by the time-constant of the RC network on pin MODE.
[7] At a junction temperature of approximately Tact(th_fold) − 5 °C, gain reduction commences and at a junction temperature of approximately
Tact(th_prot), the amplifier switches off.

slope is directly related to the time-constant

of the RC network on the MODE pin
VO (V)
VO(offset)(on)
Standby Mute On
VO(offset)(mute)
0 0.8 2.2 3.0 4.2 5.5

VMODE (V)
coa021
Fig 8. Behavior of mode selection pin MODE
12. Dynamic characteristics
12.1 Switching characteristics

Table 9. Dynamic characteristics
VP[1] = ±35 V; Tamb = 25 °C; unless otherwise specified.
Internal oscillator
fosc(typ) typical oscillator frequency ROSC = 30.0 kΩ 290 345 365 kHz
fosc oscillator frequency 250 - 450 kHz
External oscillator input or frequency tracking; pin OSC
VOSC voltage on pin OSC HIGH-level SGND + 4.5 SGND + 5 SGND + 6 V
Vtrip trip voltage - SGND + 2.5 - V
ftrack tracking frequency [2] 500 - 900 kHz
Zi input impedance 1 - - MΩ
Ci input capacitance - - 15 pF
tr(i) input rise time from SGND + 0 V [3] - - 100 ns
SGND + 5 V

[2] When using an external oscillator, the frequency ftrack (500 kHz minimum, 900 kHz maximum) will result in a PWM frequency fosc
(250 kHz minimum, 450 kHz maximum) due to the internal clock divider; see Section 8.2.
[3] When tr(i) > 100 ns, the output noise floor will increase.

12.2 Stereo SE configuration characteristics

VP[1] = ±35 V; RL = 4 Ω; fi = 1 kHz; fosc = 345 kHz; RsL[2] < 0.1 Ω; Tamb = 25 °C; unless otherwise specified.
Po output power Tj = 85 °C; LLC = 22 µH; CLC = 680 nF (see [3]
Figure 10)
THD + N = 10 %; RL = 4 Ω; VP = ±39 V 170 W
THD + N = 0.5 %; RL = 4 Ω; VP = ±37 V - 100 - W
THD + N = 10 %; RL = 4 Ω; VP = ±37 V - 150 - W
THD + N = 10 %; RL = 6 Ω; VP = ±37 V - 100 - W
THD total harmonic distortion Po = 1 W; fi = 1 kHz [4] - 0.05 - %
Po = 1 W; fi = 6 kHz [4] - 0.05 - %
Gv(cl) closed-loop voltage gain 29 30 31 dB
SVRR supply voltage ripple rejection between pins VDDPn and SGND
Operating mode; fi = 100 Hz [5] - 90 - dB
Operating mode; fi = 1 kHz [5] - 70 - dB
Mute mode; fi = 100 Hz [5] - 75 - dB
Standby mode; fi = 100 Hz [5] - 120 - dB
between pins VSSPn and SGND
Mute mode; fi = 100 Hz [5] - 80 - dB
Zi input impedance between one of the input pins and SGND 45 63 - kΩ
Vn(o) output noise voltage Operating mode; Rs = 0 Ω [6] - 160 - µV
Mute mode [7] - 85 - µV
αcs channel separation [8] - 70 - dB
|∆Gv| voltage gain difference - - 1 dB
αmute mute attenuation fi = 1 kHz; Vi = 2 V (RMS) [9] - 75 - dB
CMRR common mode rejection ratio Vi(CM) = 1 V (RMS) - 75 - dB
ηpo output power efficiency SE, RL = 4 Ω - 88 - %
SE, RL = 6 Ω - 90 - %
BTL, RL = 8 Ω - 88 - %
RDSon(hs) high-side drain-source on-state [10] - 200 - mΩ
resistance
RDSon(ls) low-side drain-source on-state [10] - 190 - mΩ
resistance

[2] RsL is the series resistance of the low-pass LC filter inductor used in the application.
[4] THD measured between 22 Hz and 20 kHz, using AES17 20 kHz brick wall filter; max. limit is guaranteed but may not be 100 % tested.
[5] Vripple = Vripple(max) = 2 V (p-p); measured independently between VDDPn and SGND and between VSSPn and SGND.
[6] 22 Hz to 20 kHz, using AES17 20 kHz brick wall filter.
[7] 22 Hz to 20 kHz, using AES17 20 kHz brick wall filter.

[8] Po = 1 W; fi = 1 kHz.
[9] Vi = Vi(max) = 1 V (RMS); fi = 1 kHz.
[10] Leads and bond wires included.
12.3 Mono BTL application characteristics

VP[1] = ±35 V; RL = 8 Ω; fi = 1 kHz; fosc = 345 kHz; RsL[2] < 0.1 Ω ; Tamb = 25 °C; unless otherwise specified.
Po output power Tj = 85 °C; LLC = 22 µH; CLC = 680 nF (see [3]
Figure 10)
THD + N = 10 %; RL = 8 Ω; VP = ±39 V - 340 - W
THD + N = 0.5 %; RL = 8 Ω; VP = ±37 V - 200 - W
THD + N = 10 %; RL = 8 Ω; VP = ±37 V - 300 - W
THD total harmonic distortion Po = 1 W; fi = 1 kHz [4] - 0.05 - %
Po = 1 W; fi = 6 kHz [4] - 0.05 - %
Gv(cl) closed-loop voltage gain - 36 - dB
SVRR supply voltage ripple rejection between pin VDDPn and SGND
Mute mode; fi = 100 Hz [5] - 95 - dB
between pin VSSPn and SGND
Mute mode; fi = 100 Hz [5] - 90 - dB
Zi input impedance measured between one of the input pins and 45 63 - kΩ
SGND
Vn(o) output noise voltage Operating mode; Rs = 0 Ω [6] - 190 - µV
Mute mode [7] - 45 - µV
αmute mute attenuation fi = 1 kHz; Vi = 2 V (RMS) [8] - 75 - dB
CMRR common mode rejection ratio Vi(CM) = 1 V (RMS) - 75 - dB

[2] RsL is the series resistance of the low-pass LC filter inductor used in the application.
[4] THD measured between 22 Hz and 20 kHz, using AES17 20 kHz brick wall filter; max. limit is guaranteed but may not be 100 % tested.
[5] Vripple = Vripple(max) = 2 V (p-p).
[6] 22 Hz to 20 kHz, using an AES17 20 kHz brick wall filter; low noise due to BD modulation.
[7] 22 Hz to 20 kHz, using an AES17 20 kHz brick wall filter.
[8] Vi = Vi(max) = 1 V (RMS); fi = 1 kHz.

13. Application information
13.1 Mono BTL application

When using the power amplifier in a mono BTL application, the inputs of the two channels
must be connected in parallel and the phase of one of the inputs must be inverted; see
Figure 7. In principle, the loudspeaker can be connected between the outputs of the two
single-ended demodulation filters.
13.2 Pin MODE

To ensure a pop noise-free start-up, an RC time-constant must be applied to pin MODE.
The bias-current setting of the VI converter input is directly related to the voltage on pin
MODE. In turn the bias-current setting of the VI converters is directly related to the DC
output offset voltage. A slow dV/dt on pin MODE results in a slow dV/dt for the DC output
offset voltage, ensuring a pop noise-free transition between Mute and Operating modes. A
time-constant of 500 ms is sufficient to guarantee pop noise-free start-up; see Figure 4,
Figure 5 and Figure 8 for more information.
13.3 Estimating the output power
13.3.1 Single-Ended (SE)

Maximum output power:
RL 2
----------------------------------------------------- × V P × ( 1 – t w ( min ) × 0.5 f osc )
R L + R DSon ( hs ) + R sL
P o ( 0.5% ) = ----------------------------------------------------------------------------------------------------------------------------------------- (1)
2R L
Maximum output current is internally limited to 9.2 A:
V P × ( 1 – t w ( min ) × 0.5 f osc )

I o ( peak ) = --------------------------------------------------------------------- (2)
R L + R DSon ( hs ) + R sL
Where:
• Po(0.5 %): output power at the onset of clipping

• RL: load impedance
• RDSon(hs): high-side RDSon of power stage output DMOS (temperature dependent)
• RsL: series impedance of the filter coil
• VP: single-sided supply voltage or 0.5 × (VDD + |VSS|)
• tw(min): minimum pulse width (typical 150 ns, temperature dependent)
• fosc: oscillator frequency
Remark: Note that Io(peak) should be less than 9.2 A (Section 8.3.2). Io(peak) is the sum of
the current through the load and the ripple current. The value of the ripple current is
dependent on the coil inductance and the voltage drop across the coil.

13.3.2 Bridge-Tied Load (BTL)

Maximum output power:
RL 2
------------------------------------------------------------------- × 2V P × ( 1 – t w ( min ) × 0.5 f osc )
R L + R DSon ( hs ) + R DSon ( ls )
P o ( 0.5% ) = ----------------------------------------------------------------------------------------------------------------------------------------------------------- (3)
2R L
Maximum output current internally limited to 9.2 A:
2V P × ( 1 – t w ( min ) × 0.5 f osc )

I o ( peak ) = ------------------------------------------------------------------------------------------- (4)
R L + ( R DSon ( hs ) + R DSon ( ls ) ) + 2R sL
Where:
• Po(0.5 %): output power at the onset of clipping

• RL: load impedance
• RDSon(hs): high-side RDSon of power stage output DMOS (temperature dependent)
• RDSon(ls): low-side RDSson of power stage output DMOS (temperature dependent)
• RsL: series impedance of the filter coil
• VP: single-sided supply voltage or 0.5 × (VDD + |VSS|)
• tw(min): minimum pulse width (typical 150 ns, temperature dependent)
• fosc: oscillator frequency
Remark: Note that Io(peak) should be less than 9.2 A; see Section 8.3.2. Io(peak) is the sum
of the current through the load and the ripple current. The value of the ripple current is
dependent on the coil inductance and the voltage drop across the coil.
13.4 External clock

To ensure duty cycle-independent operation, the external clock frequency is divided by
two internally. The external clock frequency is therefore twice the internal clock frequency
(typically 2 × 350 kHz = 700 kHz).
If several Class D amplifiers are used in a single application, it is recommended that all
the devices run at the same switching frequency. This can be achieved by connecting the
OSC pins together and feeding them from an external oscillator. When using an external
oscillator, it is necessary to force pin OSC to a DC level above SGND. This disables the
internal oscillator and causes the PWM to switch at half the external clock frequency.
The internal oscillator requires an external resistor ROSC, connected between pin OSC
and pin VSSA. ROSC must be removed when using an external oscillator.
The noise generated by the internal oscillator is supply voltage dependent. An external
low-noise oscillator is recommended for low-noise applications running at high supply
voltages.

13.5 Heatsink requirements

An external heatsink must be connected to the TDA8950.
Equation 5 defines the relationship between maximum power dissipation before activation
of TFB and total thermal resistance from junction to ambient.
T j – T amb
Rth ( j – a ) = -----------------------
- (5)
P
Power dissipation (P) is determined by the efficiency of the TDA8950. Efficiency

measured as a function of output power is given in Figure 20. Power dissipation can be
derived as a function of output power as shown in Figure 19.
mbl469
30
P
(W)
(1)
20
(2)
10
(3)
(4)
(5)
0
0 20 40 60 80 100
Tamb (°C)
(1) Rth(j-a) = 5 K/W.

(2) Rth(j-a) = 10 K/W.
(3) Rth(j-a) = 15 K/W.
(4) Rth(j-a) = 20 K/W.
(5) Rth(j-a) = 35 K/W.
Fig 9. Derating curves for power dissipation as a function of maximum ambient
temperature

In the following example, a heatsink calculation is made for an 8 Ω BTL application with a
±30 V supply:
The audio signal has a crest factor of 10 (the ratio between peak power and average
power (20 dB)); this means that the average output power is 1⁄10 of the peak power.
Thus, the peak RMS output power level is the 0.5 % THD level, i.e. 170 W.
The average power is then 1⁄10 × 170 W = 17 W.
The dissipated power at an output power of 17 W is approximately 7 W.
When the maximum expected ambient temperature is 50 °C, the total Rth(j-a) becomes
( 148 – 50 )
------------------------- = 14 K/W
7
Rth(j-a) = Rth(j-c) + Rth(c-h) + Rth(h-a)
Rth(j-c) (thermal resistance from junction to case) = 1.1 K/W

Rth(c-h) (thermal resistance from case to heatsink) = 0.5 K/W to 1 K/W (dependent on
mounting)
So the thermal resistance between heatsink and ambient temperature is:
Rth(h-a) (thermal resistance from heatsink to ambient) = 14 − (1.1 + 1) = 11.9 K/W
The derating curves for power dissipation (for several Rth(j-a) values) are illustrated in
Figure 9. A maximum junction temperature Tj = 150 °C is taken into account. The
maximum allowable power dissipation for a given heatsink size can be derived, or the
required heatsink size can be determined, at a required power dissipation level; see
Figure 9.
13.6 Pumping effects

In a typical stereo single-ended configuration, the TDA8950 is supplied by a symmetrical
supply voltage (e.g. VDD = 30 V and VSS = −30 V). When the amplifier is used in an SE
configuration, a ‘pumping effect’ can occur. During one switching interval, energy is taken
from one supply (e.g. VDD), while a part of that energy is returned to the other supply line
(e.g. VSS) and vice versa. When the voltage supply source cannot sink energy, the voltage
across the output capacitors of that voltage supply source increases and the supply
voltage is pumped to higher levels. The voltage increase caused by the pumping effect
depends on:
• Speaker impedance
• Supply voltage
• Audio signal frequency
• Value of supply line decoupling capacitors
• Source and sink currents of other channels
Pumping effects should be minimized to prevent the malfunctioning of the audio amplifier
and/or the voltage supply source. Amplifier malfunction due to the pumping effect can
trigger UVP, OVP or UBP.

The most effective way to avoid pumping effects is to connect the TDA8950 in a mono
full-bridge configuration. In the case of stereo single-ended applications, it is advised to
connect the inputs in anti-phase (see Section 8.4). The power supply can also be
adapted; for example, by increasing the values of the supply line decoupling capacitors.
13.7 Application schematic

Notes on the application schematic:
• Connect a solid ground plane around the switching amplifier to avoid emissions
• Place 100 nF capacitors as close as possible to the TDA8950 power supply pins
• Connect the heatsink to the ground plane or to VSSPn using a 100 nF capacitor
• Use a thermally conductive, electrically non-conductive, Sil-Pad between the
TDA8950 heat spreader and the external heatsink
• The heat spreader of the TDA8950 is internally connected to VSSD
• Use differential inputs for the most effective system level audio performance with
unbalanced signal sources. In case of hum due to floating inputs, connect the
shielding or source ground to the amplifier ground.

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet
TDA8950_2
NXP Semiconductors
+5 V
RVDDA
VDDA 5.6 kΩ
10 Ω 470 Ω
mode control
VDDP VDDP
CVDDP SINGLE-ENDED
+5 V OUTPUT FILTER VALUES
470 µF
CVP LOAD LLC CLC
GND 22 µF
470 kΩ 5.6 kΩ 10 µF 470 kΩ
CVSSP 3 Ω to 6 Ω 15 µH 680 nF
470 µF
4 Ω to 8 Ω 22 µH 470 nF
VSSP VSSP
10 kΩ 10 kΩ
RVSSA mute/ T1 standby/ T2
VSSA operating HFE > 80 operating HFE > 80
10 Ω
SGND
VSSA mode VDDP VSSP

control
CVDDP CVP CVSSP
ROSC VDDP
30 kΩ CSN
100 nF 100 nF 100 nF
RSN 220 pF
VDDP1
Rev. 02 — 11 June 2009
VSSP1
MODE
n.c. n.c. n.c.
OSC
10 Ω CSN
220 pF
CIN 4 5 6 1 23 8 11
+ IN1P
2 VSSP
LLC
470 nF OUT1
IN1 10
CIN
− IN1M CBO RZO
+
3 BOOT1 22 Ω
470 nF 9 CLC
15 nF CZO −
SGND 100 nF
19 TDA8950J
CBO
CIN
BOOT2
15
− IN2P
22 15 nF
470 nF LLC

IN2 OUT2
14
CIN
+ IN2M
21 VDDP RZO
470 nF 22 Ω −
CSN CLC
20 18 12 7 17 16 13 RSN 220 pF CZO +
VDDA
VSSA
STABI
PROT
VSSD
VDDP2
VSSP2
100 nF
10 Ω CSN
220 pF
CVDDA CVSSA CVDDP CVP CVSSP
TDA8950
VSSP
© NXP B.V. 2009. All rights reserved.
CPROT(1)
CSTAB
220 nF 220 nF 100 nF 100 nF 100 nF
470 nF
VDDA VSSA VSSP VSSA VDDP VSSP 010aaaxxx

22 of 39
(1) The value of CPROT can be in the range 10 pF to 220 pF (see Section 8.3.2)
Fig 10. Typical application diagram
13.8 Curves measured in reference design
010aaa553
10
THD
(%)
(1)
10−1
(2)
10−2 (3)
10−3
10−2 10−1 1 10 102 103
Po (W)
VP = ±35 V, fosc = 345 kHz, 2 × 4 Ω SE configuration.

(1) fi = 6 kHz.
(2) fi = 1 kHz.
(3) fi = 100 Hz.
Fig 11. THD + N as a function of output power, SE configuration with 2 × 4 Ω load
010aaa554
10
THD
(%)
(1)
10−1
(2)
10−2 (3)
10−3
10−2 10−1 1 10 102 103
Po (W)

(1) fi = 6 kHz.
(2) fi = 1 kHz.
(3) fi = 100 Hz.
Fig 12. THD + N as a function of output power, SE configuration with 2 × 6 Ω load

001aai423
10
THD
(%)
(1)
10−1
(2)
10−2 (3)
10−3
10−2 10−1 1 10 102 103
PO (W)
VP = ±35 V, fosc = 345 kHz, 1 × 8 Ω BTL configuration.

(1) fi = 6 kHz.
(2) fi = 1 kHz.
(3) fi = 100 Hz.
Fig 13. THD + N as a function of output power, BTL configuration with 1 × 8 Ω load
001aai424
10
THD
(%)
10−1
(1)
10−2 (2)
10−3
10 102 103 104 105
fi (Hz)
VP = ±35 V, fosc = 345 kH, 2 × 4 Ω SE configuration.

(1) Po = 1 W.
(2) Po = 10 W.
Fig 14. THD + N as a function of frequency, SE configuration with 2 × 4 Ω load

001aai701
10
THD
(%)
10−1
(1)
10−2 (2)
10−3
10 102 103 104 105
fi (Hz)

(1) Po = 1 W.
(2) Po = 10 W.
Fig 15. THD + N as a function of frequency, SE configuration with 2 × 6 Ω load
001aai702
10
THD
(%)
10−1
(1)
10−2
(2)
10−3
10 102 103 104 105
fi (Hz)
VP = ±35 V, fosc = 345 kHz, 1 × 8 Ω BTL configuration.

(1) Po = 1 W.
(2) Po = 10 W.
Fig 16. THD + N as a function of frequency, BTL configuration with 1 × 8 Ω load

001aai703
0
αcs
(dB)
−20
−40
−60
−80
−100
10 102 103 104 105
fi (Hz)

1 W and 10 W respectively.
Fig 17. Channel separation as a function of frequency, SE configuration with 2 × 4 Ω load
001aai704
0
αcs
(dB)
−20
−40
−60
−80
−100
10 102 103 104 105
fi (Hz)

1 W and 10 W respectively.
Fig 18. Channel separation as a function of frequency, SE configuration with 2 × 6 Ω load

001aai705
40
P
(W)
35
30
25
(1)
20
(2)
15
(3)
10
0
0 20 40 60 80 100 120
Po (W)
VP = ±35 V, fi = 1 kHz; fosc = 345 kHz.

(1) 2 × 4 Ω SE configuration.
Fig 19. Power dissipation as a function of output power per channel, SE configuration
001aai706
100
(1) (2)
η
(%) (3)
80
60
40
20
0
0 20 40 60 80 100 120
Po (W)
VP = ±35 V, fi = 1 kHz, fosc = 345 kHz.

Fig 20. Efficiency as a function of output power per channel, SE configuration

001aai707
200
Po
(W)
180
160
140
120
(1)
100
(2)
80
(3)
60
(4)
40
20
0
12.5 15 17.5 20 22.5 25 27.5 30 32.5 35 37.5 40
Vp (V)
Infinite heat sink used.

fi = 1 kHz, fosc = 345 kHz.
(1) THD + N = 10 %, 4 Ω.
(2) THD + N = 0.5 %, 4 Ω; THD + N = 10 %, 6 Ω.
(3) THD + N = 10 %, 8 Ω; THD + N = 0.5 %, 6 Ω
(4) THD + N = 0.5 %, 8 Ω.
Fig 21. Output power as a function of supply voltage, SE configuration
001aai708
350
Po
(W)
300
250
(1)
200
(2)
150
(3)
100 (4)
50
0
12.5 15 17.5 20 22.5 25 27.5 30 32.5 35 37.5 40
Vp (V)
Infinite heat sink used.

fi = 1 kHz, fosc = 345 kHz.
(1) THD + N = 10 %, 8 Ω.
(2) THD + N = 0.5 %, 8 Ω.
(3) THD + N = 10 %, 16 Ω.
(4) THD + N = 0.5 %, 16 Ω.
Fig 22. Output power as a function of supply voltage, BTL configuration

001aai709
45
Gv(cl)
(dB)
40
(1)
35
(2)
30
(3)
(4)
25
20
10 102 103 104 105
fi (Hz)
VP = ±35 V, fosc = 345 kHz, Vi = 100 mV, Ci = 330 pF, LLC = 15 µH, CLC = 680 nF.
(1) 1 × 8 Ω BTL configuration.
Fig 23. Closed-loop voltage gain as a function of frequency
001aai710
−20
SVRR
(dB)
−40
−60
(1)
−80
(2)
−100
−120 (3)
−140
10 102 103 104 105
fripple (Hz)
Ripple on VDD, short on input pins.

VP = ±35 V, fosc = 345 kHz, RL = 4 Ω, Vripple = 2 V (p-p).
(1) Mute mode.
(2) Operating mode.
(3) Standby mode.
Fig 24. SVRR as a function of ripple frequency, ripple on VDD

001aai711
−20
SVRR
(dB)
−40
−60
−80
(2)
(1)
−100
−120 (3)
−140
10 102 103 104 106
fripple (Hz)
Ripple on VSS, short on input pins.

VP = ±35 V, fosc = 345 kHz, RL = 4 Ω, Vripple = 2 V (p-p).
(1) Mute mode.
(2) Operating mode.
(3) Standby mode.
Fig 25. SVRR as a function of ripple frequency, ripple on VSS
001aai712
10
Vo
(V)
1
10−1
10−2
10−3
10−4
(1) (2)
10−5
10−6
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
VMODE (V)
VP = ±35 V, fosc = 345 kHz.

(1) Mode voltage down.
(2) Mode voltage up.
Fig 26. Output voltage as a function of mode voltage

001aai713
−50
αmute
(dB)
−60
−70
(1)
(2)
(3)
−80
−90
10 102 103 104 105
fi (Hz)
VP = ±35 V, fosc = 325 kHz, Vi = 2 V (RMS).

(1) 8 Ω.
(2) 6 Ω.
(3) 4 Ω.
Fig 27. Mute attenuation as a function of frequency

14. Package outline
DBS23P: plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1
non-concave
x Dh
Eh
view B: mounting base side
A2
d A5
β A4
B E2
j
E
E1
L2
L1 L3
L Q c v M
1 23
e1 m e2
Z w M
bp
e
0 5 10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT A 2 A4 A5 bp c D (1) d D h E (1) e e1 e2 Eh E1 E2 j L L1 L2 L3 m Q v w x β Z (1)
4.6 1.15 1.65 0.75 0.55 30.4 28.0 12.2 6 10.15 6.2 1.85 3.6 14 10.7 2.4 2.1 1.43
mm 12 2.54 1.27 5.08 4.3 0.6 0.25 0.03 45°
4.3 0.85 1.35 0.60 0.35 29.9 27.5 11.8 9.85 5.8 1.65 2.8 13 9.9 1.6 1.8 0.78
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC JEITA PROJECTION
98-02-20
SOT411-1
02-04-24
Fig 28. Package outline SOT411-1 (DBS23P)


HSOP24: plastic, heatsink small outline package; 24 leads; low stand-off height SOT566-3
E A
D
x X
y E2
HE v M A
D1
D2
1 12
pin 1 index
A2 A
E1 (A3)
A4
θ
Lp
detail X
24 13
Z w M
e bp
0 5 10 mm
scale
DIMENSIONS (mm are the original dimensions)

A
UNIT A2 A3 A4(1) bp c D(2) D1 D2 E(2) E1 E2 e HE Lp Q v w x y Z θ
max.
3.5 +0.08 0.53 0.32 16.0 13.0 1.1 11.1 6.2 2.9 14.5 1.1 1.7 2.7 8°
mm 3.5 0.35 1 0.25 0.25 0.03 0.07
3.2 −0.04 0.40 0.23 15.8 12.6 0.9 10.9 5.8 2.5 13.9 0.8 1.5 2.2 0°
Notes
1. Limits per individual lead.
2. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC JEITA PROJECTION
03-02-18
SOT566-3
03-07-23
Fig 29. Package outline SOT566-3 (HSOP24)


15. Soldering of SMD packages

This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
15.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
15.2 Wave and reflow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
15.3 Wave soldering

Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities

15.4 Reflow soldering

Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 30) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 12 and 13
Table 12. SnPb eutectic process (from J-STD-020C)

Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350 ≥ 350
< 2.5 235 220
≥ 2.5 220 220
Table 13. Lead-free process (from J-STD-020C)

Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350 350 to 2000 > 2000
< 1.6 260 260 260
1.6 to 2.5 260 250 245
> 2.5 250 245 245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 30.

maximum peak temperature

temperature = MSL limit, damage level
minimum peak temperature

= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level

Fig 30. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365

“Surface mount reflow soldering description”.
16. Soldering of through-hole mount packages
16.1 Introduction to soldering through-hole mount packages

This text gives a very brief insight into wave, dip and manual soldering.
Wave soldering is the preferred method for mounting of through-hole mount IC packages
on a printed-circuit board.
16.2 Soldering by dipping or by solder wave

Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing. Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250 °C or 265 °C, depending on solder material applied, SnPb
or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
16.3 Manual soldering

Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300 °C and 400 °C, contact may be up to 5 seconds.

16.4 Package related soldering information

Table 14. Suitability of through-hole mount IC packages for dipping and wave soldering
Package Soldering method
Dipping Wave
CPGA, HCPGA - suitable
DBS, DIP, HDIP, RDBS, SDIP, SIL suitable suitable[1]
PMFP[2] - not suitable
[1] For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit
board.
[2] For PMFP packages hot bar soldering or manual soldering is suitable.
17. Revision history

Table 15. Revision history
Document ID Release date Data sheet status Change notice Supersedes
TDA8950_2 20090611 Product data sheet TDA8950_1
Modifications • Parameter values revised throughout.
• Revised Figure 4, Figure 10, Figure 11 and Figure 12.
TDA8950_1 20080909 Preliminary data sheet - -

18. Legal information
18.1 Data sheet status

Document status[1][2] Product status[3] Definition
Objective [short] data sheet Development This document contains data from the objective specification for product development.
Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.
Product [short] data sheet Production This document contains the product specification.
[1] Please consult the most recently issued document before initiating or completing a design.
[2] The term ‘short data sheet’ is explained in section “Definitions”.
[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
18.2 Definitions damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in Applications — Applications that are described herein for any of these
modifications or additions. NXP Semiconductors does not give any products are for illustrative purposes only. NXP Semiconductors makes no
representations or warranties as to the accuracy or completeness of representation or warranty that such applications will be suitable for the
information included herein and shall have no liability for the consequences of specified use without further testing or modification.
use of such information. Limiting values — Stress above one or more limiting values (as defined in
Short data sheet — A short data sheet is an extract from a full data sheet the Absolute Maximum Ratings System of IEC 60134) may cause permanent
with the same product type number(s) and title. A short data sheet is intended damage to the device. Limiting values are stress ratings only and operation of
for quick reference only and should not be relied upon to contain detailed and the device at these or any other conditions above those given in the
full information. For detailed and full information see the relevant full data Characteristics sections of this document is not implied. Exposure to limiting
sheet, which is available on request via the local NXP Semiconductors sales values for extended periods may affect device reliability.
office. In case of any inconsistency or conflict with the short data sheet, the Terms and conditions of sale — NXP Semiconductors products are sold
full data sheet shall prevail. subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
18.3 Disclaimers explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
General — Information in this document is believed to be accurate and terms and conditions, the latter will prevail.
reliable. However, NXP Semiconductors does not give any representations or
No offer to sell or license — Nothing in this document may be interpreted
warranties, expressed or implied, as to the accuracy or completeness of such
or construed as an offer to sell products that is open for acceptance or the
information and shall have no liability for the consequences of use of such
grant, conveyance or implication of any license under any copyrights, patents
information.
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
Export control — This document as well as the item(s) described herein
changes to information published in this document, including without
may be subject to export control regulations. Export might require a prior
limitation specifications and product descriptions, at any time and without
authorization from national authorities.
notice. This document supersedes and replaces all information supplied prior
to the publication hereof. Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
Suitability for use — NXP Semiconductors products are not designed,
document, and as such is not complete, exhaustive or legally binding.
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
18.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
19. Contact information

For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]

20. Contents
1 General description . . . . . . . . . . . . . . . . . . . . . . 1 16.1 Introduction to soldering through-hole mount
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16.2 Soldering by dipping or by solder wave . . . . . 36
16.3 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 36
4 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
16.4 Package related soldering information . . . . . . 37
5 Ordering information . . . . . . . . . . . . . . . . . . . . . 2
17 Revision history . . . . . . . . . . . . . . . . . . . . . . . 37
6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
18 Legal information . . . . . . . . . . . . . . . . . . . . . . 38
7 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 18.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 38
7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 18.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 18.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8 Functional description . . . . . . . . . . . . . . . . . . . 5 18.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 19 Contact information . . . . . . . . . . . . . . . . . . . . 38
8.2 Pulse-width modulation frequency . . . . . . . . . . 8 20 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.3 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
8.3.1 Thermal protection . . . . . . . . . . . . . . . . . . . . . . 8
8.3.1.1 Thermal FoldBack (TFB) . . . . . . . . . . . . . . . . . 8
8.3.1.2 OverTemperature Protection (OTP) . . . . . . . . . 9
8.3.2 OverCurrent Protection (OCP) . . . . . . . . . . . . . 9
8.3.3 Window Protection (WP). . . . . . . . . . . . . . . . . 10
8.3.4 Supply voltage protection . . . . . . . . . . . . . . . . 11
8.4 Differential audio inputs . . . . . . . . . . . . . . . . . 11
9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 12
10 Thermal characteristics. . . . . . . . . . . . . . . . . . 12
11 Static characteristics. . . . . . . . . . . . . . . . . . . . 13
12 Dynamic characteristics . . . . . . . . . . . . . . . . . 14
12.1 Switching characteristics . . . . . . . . . . . . . . . . 14
12.2 Stereo SE configuration characteristics . . . . . 15
12.3 Mono BTL application characteristics . . . . . . . 16
13 Application information. . . . . . . . . . . . . . . . . . 17
13.1 Mono BTL application . . . . . . . . . . . . . . . . . . . 17
13.2 Pin MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
13.3 Estimating the output power . . . . . . . . . . . . . . 17
13.3.1 Single-Ended (SE) . . . . . . . . . . . . . . . . . . . . . 17
13.3.2 Bridge-Tied Load (BTL) . . . . . . . . . . . . . . . . . 18
13.4 External clock . . . . . . . . . . . . . . . . . . . . . . . . . 18
13.5 Heatsink requirements . . . . . . . . . . . . . . . . . . 19
13.6 Pumping effects . . . . . . . . . . . . . . . . . . . . . . . 20
13.7 Application schematic . . . . . . . . . . . . . . . . . . . 21
13.8 Curves measured in reference design . . . . . . 23
14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 32
15 Soldering of SMD packages . . . . . . . . . . . . . . 34
15.1 Introduction to soldering . . . . . . . . . . . . . . . . . 34
15.2 Wave and reflow soldering . . . . . . . . . . . . . . . 34
15.3 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 34
15.4 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 35
16 Soldering of through-hole mount packages . 36
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009. All rights reserved.

For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 11 June 2009
Document identifier: TDA8950_2
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
NXP:
TDA8950J/N1,112 TDA8950TH/N1,118

Tda8950 1902105

Uploaded by

Copyright:

Available Formats

Tda8950 1902105

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tda8950 1902105

Uploaded by

Copyright:

Available Formats

TDA8950

2 × 150 W class-D power amplifier

4. Quick reference data

(see Figure 10)

[1] VP is the supply voltage on pins VDDP1, VDDP2 and VDDA.

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 2 of 39

VDDA n.c. STABI PROT VDDP2 VDDP1

3 (20) 10 (4) 18 (12) 13 (7) 23 (16) 14 (8)

1 (18) 12 (6) 24 (17) 19 (-) 17 (11) 20 (13) 001aah653

VSSA n.c. VSSD n.c. VSSP1 VSSP2

Pin numbers in brackets refer to type number TDA8950J.

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 3 of 39

Fig 2. Pin configuration TDA8950TH Fig 3. Pin configuration TDA8950J

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 4 of 39

7.2 Pin description

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 5 of 39

• Standby mode: featuring very low quiescent current

Fig 4. Example of mode selection circuit

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 6 of 39

(1) First 1⁄4 pulse down.

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 7 of 39

8.2 Pulse-width modulation frequency

8.3.1 Thermal protection

8.3.1.1 Thermal FoldBack (TFB)

Tact(th_fold) − 5 °C < Tact(th_fold) < Tact(th_prot)

Product data sheet Rev. 02 — 11 June 2009 8 of 39

8.3.1.2 OverTemperature Protection (OTP)

The thermal behavior is illustrated in Figure 6.

8.3.2 OverCurrent Protection (OCP)

The TDA8950 amplifier distinguishes between low-ohmic short-circuit conditions and

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 9 of 39

[1] VP is the supply voltage on pins VDDP1, VDDP2 and VDDA.

8.3.3 Window Protection (WP)

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 10 of 39

8.3.4 Supply voltage protection

Table 5. Overview of TDA8950 protection circuits

8.4 Differential audio inputs

• Stereo operation: to avoid acoustical phase differences, the inputs should be in

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 11 of 39

Fig 7. Input configuration for mono BTL application

Tstg storage temperature −55 +150 °C

[1] VP is the supply voltage on pins VDDP1, VDDP2 and VDDA.

10. Thermal characteristics

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 12 of 39

11. Static characteristics

[1] VP is the supply voltage on pins VDDP1, VDDP2 and VDDA.

TDA8950_2 © NXP B.V. 2009. All rights reserved.

Product data sheet Rev. 02 — 11 June 2009 13 of 39

slope is directly related to the time-constant