Chapter 2

2 Programmable Logic
Controller (PLC)
2.1 BASICS OF PLC

2.1.1 Invention of PLC
Programmable Logic Controller (PLC) was originally designed and developed
in 1968 by General Motors (GM) for replacing hardwired relay logic circuit. In a
changing production line, any modification of hardwired relay logic circuit would
entail considerable cost and time overrun, as it involved a number of constraints for
both technicians and control engineers.
• Lack of flexibility as well as the large time needed for any change in wiring
of the hardwired circuit.
• A major issue of troubleshooting with soiled and worn-out contacts, loose
wires, and difficulty with connection diagrams.
To overcome the limitations of such hardwire-based relay logic (Figure 2.1), a group
of engineers at GM proposed a new design of ‘Standard Machine Controller’ which
was the primitive form of PLC. Based on this idea, four major companies (Allen-
Bradley, Digital Equipment Corporation, Century Detroit, and Bedford Associates)
attempted to build a prototype.
Bedford Associates first successfully designed PLC for commercial use of General
Motors in 1969. In 1974, Allen-Bradley introduced a new design to satisfy the cus-
tomers’ needs and named their device as ‘Programmable Logic Controller’ (PLC)
over the then-accepted term ‘Programmable Controller’. During this introductory
phase of PLC, Richard Morley, known as the father of PLC, contributed a lot toward
its development. He originally designed the ladder logic for PLC programming. Odo
Josef Struger of Allen-Bradley also contributed a lot for the development of PLC.
Some of the milestones toward the development of PLC are shown in Figure 2.2.
2.1.2 Sustainability of PLC

Since its introduction around 50 years ago, PLC still is playing a major role in pro-
cess automation. As per Chris Elston of Yamaha Robotics ‘Probably 95% of machine
builders still use PLCs as the controller of choice when they design a piece of
machinery. There really aren’t a lot of people who have switched over to something
like programmable automation controllers (PACs) or personal computer (PC)-based
control or anything of that nature’. Software-based PLCs didn’t get much acceptance
due to the failure issues with computers. The simplicity of PLCs lies with its ladder
15
16 Industrial Automation Technologies
FIGURE 2.1 A panel consisting of hardwired logic.
logic programming. In industrial environment, technicians are more conversant

with Ladder Diagram (LD) than high-end cryptic programming languages. An
industry survey shows that 80% of PLCs are used in small applications (1 to 128
input-output (I/O) points), 78% of PLC I/Os are digital, and 80% of PLC appli-
cation challenges are solved with a set of 20 ladder logic instructions. Another
important feature of a PLC is its robustness against process hazards like vibra-
tion, dust, temperature, etc. Cost advantage along with large installations and
training of manpower over a span of 30–40 years provides PLCs its sustainability
in the days to come.
2.1.3 Definition of PLC

A PLC is a special form of microprocessor-based dedicated computer control system
that continuously monitors the state of input devices and makes decisions based on a
custom program to control the output devices.
In its primitive form, a PLC could do with only logical inputs and logical outputs.
However, presently they can handle both digital and analog signals. Almost any pro-
duction line, machine function, or process can be greatly enhanced using this type of
control system. Its user-friendly features help an operator with minimal knowledge
FIGURE 2.2 Progress of PLC with time.

Programmable Logic Controllers 17
FIGURE 2.3 Schematic diagram of a PLC.
in computer to work with. Versatility, flexibility, cost efficacy, and ruggedness pro-
vide the PLC a special edge in process automation. The schematic diagram of a PLC
is shown in Figure 2.3.
2.1.4 Classifications of PLCs

PLCs are available with a wide range of specifications and performance. Hence, it is
difficult to classify them in a straightforward way. However, classification of PLCs
can be made based on their various parameters like structure, functionality, I/O han-
dling capacity, etc.
• Structural classification: As far as the structure of a PLC is concerned, it

can be classified into two categories:
1. Integral – Integral PLC is an integrated unit comprising Power Supply
Unit (PSU), Central Processing Unit (CPU), and I/O interfaces along
with other components. It is small in size with compact structure and
low price.
2. Modular – Modular PLC usually has a frame where power sup-
ply module, CPU module, I/O module, and other functional mod-
ules can be connected. It has a flexible configuration where users
can choose the add-on modules and hence its size can vary from
medium to large.
There is still another class of PLC which contains the combined
features of integral and modular PLCs and it is called stacked PLC.
• Functional classification: Depending on the function of the PLC, it can be
classified into low-, medium-, and high-grade categories.
1. Low grade: It is mainly used for logical operation, sequential opera-
tion, or a few analog operations of standalone control systems.
2. Medium grade: It supports all low-grade operations along with arith-
metic operation, comparison of data transfer, number conversion,
remote I/O, subroutines, interrupt control, etc. for controlling complex
control systems.
3. High grade: It supports all the low- and medium-grade functions along
with matrix operation, bit operation, etc. It also supports networking
communication for controlling large process plants.
• I/O point-based classification: Depending on the number of available I/O

points, a PLC can be classified into small, medium, and large categories.
1. Small I/O: In case of small PLCs, the number of I/O points is usu-
ally lesser than 256 with a single CPU (8 bit) and memory capacity 4K
words or less; e.g., Siemens S7-200.
2. Medium I/O: In case of medium PLCs, the number of I/O points usu-
ally remain in between 256 and 2048 with dual CPUs (16 bit) and mem-
ory capacity is within 8K words; e.g., Siemens S7-300.
3. Large I/O: Number of I/O points for large PLCs is larger than 2048,
multi CPUs (16 bit or 32 bit), and architecture with memory size 8K–16K
words; e.g., Siemens S7-400.
2.1.5 Role of PLC in Process Automation

In process automation, from robotic arm movements in the automotive industry to
safety aspects of chemical plants, PLCs play a major role. With time it is gaining more
popularity as additional features are being incorporated with PLC functioning. In any
automation-based control system, the basic consideration is to derive the desired out-
put in an effective and reliable way. PLCs provide a simple and cost-effective solution
to many automation tasks like logic/sequence control, Proportional-Integral-Derivative
(PID) control and computing, coordination and communication, operator control and
monitoring, safety of plant equipment and personnel, plant startup and shutdown, etc.
Most of the manufacturing applications involve controlling repetitive and discrete
operations; e.g., automatic assembly of components, molding and extrusion, printing
in textile operations, etc. Some typical industrial areas where PLCs are extensively
used are shown in Table 2.1.
2.1.6 Features of a PLC
A PLC has a number of features that would satisfy various requirements in process
automation:
1. Flexibility: If there is any change in process operations or any change in

plant machinery or equipment, necessary changes in PLC programming
can be done very easily without causing any delay in plant operation.
TABLE 2.1
Industrial Applications of PLC
2. Easy troubleshooting: PLC program can be easily tested and evaluated

offline and hence any correction or change can easily be incorporated
within a very short span of time.
3. Lesser cost: Advanced technology provides PLCs with more functionality
(Timer, Counter, Sequencer, etc.) at a lesser cost compared to other avail-
able controlling devices.
4. Large number of I/O contacts: PLCs are provided with a large number
of I/O contacts and hence additional I/Os can be easily accommodated
through small change in programming. According to the manufacturers’
guidelines, sizing of any PLC system should be done in such a way that it
must allow 20% expansion for future.
5. Easy programming: Ladder logic is a very simple and effective way for
PLC programming. Without having a background of computer knowledge,
technicians can easily draw ladder logic and implement any modification of
the existing programs, if required.
6. Strong reliability: Compared to electromechanical relay units, PLCs are
made of solid-state components and hence are more reliable. As a result,
maintenance cost is quite low and downtime is minimal.
7. Visual interface: Modern PLCs usually have PC-based user interface
where an operator can perform programming as well as troubleshooting
more conveniently due to visual presentation.
8. Higher speed of operation: Operational speed of PLCs is very fast, usu-
ally termed as ‘scan time’ which is in the order of milliseconds.
9. Faster installation and commissioning: Being a package item, PLCs are
available with all of its accessories – hardware as well as software compo-
nents. So, their installation and commissioning duration is relatively small
compared to other controlling equipment.
10. Good documentation and strong security: All the necessary documents
(hard and soft copies) are supplied with PLCs and hence technicians can
easily access them. Security features of PLCs are quite strong with hard-
ware and software locks and hence any unauthorized access can easily be
prevented.
11. Fail safe operation: In case of modular PLCs, important modules
like power supply, CPU, and I/O can be duplex in nature to avoid any
type of failure related to hardware modules and add redundancy to the
system.
12. Networking facility: As control systems are becoming more complex,
for their effective controlling, PLCs must communicate with each other.
Modern PLCs can be placed in a network for data exchange to accomplish
a control task in a more effective way.
13. Connectivity of peripheral devices: Peripheral devices like printer and
storage devices like third-party items can be connected to PLCs.
14. Rugged construction: PLCs are usually quite rugged to operate in the
harsh environment of plants, i.e., in the presence of humidity, dust, vibra-
tion, temperature, etc. It can operate over a temperature range of 0° C to
60° C, with relative humidity ranging from 0% to 95% noncondensing.
It has strong electrical noise immunity. Manufacturers’ report depicts

that for a typical industrial PLC, mean time between failures ranges from
20,000 to 50,000 hours, which is reasonably high.
Another advantageous feature of PLCs is that it allows piecemeal implementation of

the projects. So, with all such important features, PLCs have always remained a very
sought-after controlling device for process industries.
2.1.7 I/O Devices of PLC

In the primitive form of PLCs, it used to take logical inputs, mainly from various
switches, like level switch, pressure switch, temperature switch, push button, prox-
imity detector, etc. Similarly, it used to provide logical output for relay, solenoid
valve, starter, etc. But, presently it can take input in the form of bit pattern, pulse
train, and even analog signal and can provide similar form of outputs. Various input
and output devices connected to PLCs in process industries are shown in Table 2.2a
and Table 2.2b.
TABLE 2.2a
Input Devices Connected to the PLC
Type Purpose Figure

Switch (level, pressure, Status of process parameters
temperature, etc.) used for feedback
Limit switch Positional status
Proximity detector Positional status of the objects
Push button Command input
Thumbwheel switch To provide set value
Photoelectric switch Positional status of the objects
Thermostat Temperature status

TABLE 2.2b
Output Devices Connected to the PLC
Type Purpose Figure

Relay Isolated electrical contact
Solenoid valve Flow control
Starter Starting of a motor
Display lamp Status information display
2.1.8 PLC Programming Devices

Figure 2.4 shows various PLC programming devices.
PLC programming is an important part in a PLC-based process automation system.
To load a program in a PLC, usually three types of devices (Figure 2.4), known as pro-
gram loader, are used. At the lower end, a handheld programmer (palm-sized) is used
with keypads and display. A more user-friendly version contains a larger display unit with
FIGURE 2.4 Various PLC programming devices.

dedicated keys. But, at present, desktop or laptop PCs are more popular for PLC pro-
gramming. There are five different PLC programming languages: LD, functional block
diagram, Sequential Function Chart (SFC), Structured Text (ST), and Instruction List (IL).
There are two ways of entering programs in a PLC:
1. Direct program entry to the program memory (random access memory

[RAM]) plugged into the central controller. For this purpose, the program-
mer is connected to the processor or to the programmer interface modules.
2. Programming the erasable and programmable read-only memory (EPROM)
submodules in the programmer without connecting it to the PC (offline).
The memory submodules are then plugged into the central controller.
2.1.9 PLC Selection Criteria

Selection of a suitable PLC for a particular industrial application is very crucial.
It depends on several factors like:
• System requirements: It basically defines the task to be executed by the

intended PLC, so the goal to be achieved must be clearly defined. Hence,
the entire task is required to be segregated into a number of simple steps
which are easily comprehensible.
• Application requirements: Nature of input and output devices to be con-
nected to a PLC and a list of functions required for each of these devices.
Other than the logical operations (On/Off), if any other special type of func-
tion is required or not? What is the required number of inputs and outputs?
What is the required size of memory along with speed requirement of CPU?
• Electrical requirements: It signifies the electrical power requirements,
i.e., the voltage and current rating for individual input and output as well as
for the PLC itself.
• Speed of operation: We need to define the speed of operation of the
intended PLC depending on the nature of the plant dynamics. It is very sig-
nificant in case of ‘time critical’ operations as well as for safety functions.
• Communication: If the application requires sharing of data outside the
process, i.e., communication with the operator station.
• Environmental conditions: Harshness of the operating conditions where
the PLC is to be housed as it dictates the enclosure specifications along with
accessibility for maintenance and troubleshooting.
2.1.10 Major PLC Vendors and their Products

The global PLC market is highly fragmented with the presence of several established
vendors. The primary success factors in PLC market concerns:
• Availability of a wide range of products equipped with appropriate external

expansion units and software programs to address industry demand
• Functional reliability of the products over a long period of operation
• Competitive prices with advanced functionalities

• Satisfactory after-sales service and efficient technical support
• Strong distribution network
To stay competitive in the market, PLC vendors are providing integrated and com-
plete solutions across end user industries that are looking for solutions which will
reduce the engineering and other related expenses. PLC market consists of three
types of vendors:
• Tier 1 manufacturers in the automation industry are Siemens, Rockwell

Automation (Allen-Bradley), Schneider Electric, Mitsubishi Electric,
Omron, ABB, and GE. These companies provide a one-stop solution to end
users, and their distribution network includes direct sales through manufac-
turers and system integrators.
• Tier 2 manufacturers include Yokogawa, Bosch Rexroth, Toshiba
International, B&R Industrial Automation, Phillips Components, and
Festo. They provide products specifically for end user requirements, and
companies depend on a well-established network of distributors to sell their
products.
• Tier 3 manufacturers are small organizations that have limited geographi-
cal presence and deal in micro PLCs designed for special niche applica-
tions. Some such companies include Kim Controls, Horner Electric, SEE
Automation & Engineers, etc.
2.1.10.1 Top Five PLC Vendors

• Rockwell Automation: In the PLC market, Rockwell Automation is known
as Allen-Bradley and it offers PLCs for large (ControlLogix 5580, 5570),
small (CompactLogix 5370, 5380), and micro (MicroLogix 810, 820) con-
trol systems with wide range of products.
• Schneider Electric: Schneider Electric offers PLCs for industrial and com-
mercial machines. The models used in industrial applications are Modicon
M221, Modicon M238, etc. The commercial PLCs include Modicon M168,
Modicon M171, etc.
• Siemens: Siemens offers a wide range of products and solutions to vari-
ous industrial companies mainly belonging to process and manufactur-
ing industries. It provides four varieties of SIMATIC PLCs namely basic
(S7-1200), advanced (S7-1500), distributed (ET-200SP), and software con-
trollers (S7-15000).
• Mitsubishi Electric: Mitsubishi Electric offers PLCs in energy and electric
systems, industrial automation, information and communication systems,
electronic devices, and home appliances. Various models include MELSEC
iQ-R Series, MELSEC iQ-F Series, MELSEC-Q Series, MELSEC-L
Series, MELSEC-F Series, and MELSEC-QS/WS Series.
• OMRON: OMRON range of PLCs range from small-scale equipment con-

trols to production line controllers. The controller series include CJ1, CS1,
CP1, CJ2, and NSJ.
2.2 DESIGN AND OPERATION OF PLC

2.2.1 Architecture of PLC
Block diagram of a PLC is shown in Figure 2.5, while the architecture of the same
is shown in Figure 2.6.
Irrespective of the manufacturer as well as look, block diagram representation
of almost all the PLCs have a resemblance, as shown in Figure 2.5. They have sev-
eral common functional components independent of their size and features. Internal
architecture of a PLC is shown in Figure 2.6.
• Processor: Processor, i.e., CPU, is basically a microprocessor and it inter-

prets the input signals and provides the control actions, according to the
program stored in the memory. It also interfaces with display unit and
supports communication with other external devices (e.g., host computer)
through the communication module. The size of data bus and the clock
speed of the microprocessor indicate the fastness of operation of a PLC.
Usually, processors can manipulate data with bit size of 4, 8, 16, 32,
or 64, which indicates the size of data bus. From low end (small PLC) to
high end (large PLC), clock speed ranges from 1 MHz to 1 GHz. However,
as most of the industrial processes are reasonably slow, small to moder-
ate sized PLCs with moderate speed are used for such processes. Through
input scanning (run by input module), all the available inputs are stored
in data RAMs so that CPU can read the input status. Operating system of
FIGURE 2.5 Block diagram of a PLC.

FIGURE 2.6 Architecture of a PLC.
the PLC is stored in system read-only memory (ROM) which manages the
operation of the PLC. The arithmetic logic unit (ALU) section of the CPU
along with internal storage registers performs all the required arithmetic
and logical operations as per the program written in user RAM. Control
unit of CPU controls the timing of all the operations. After the execution of
the program in CPU, all the outputs are fed to the output module to change
the status of the output channels.
• Power supply and battery backup: PSU provides the necessary power
to the CPU as well as input and output modules. Most of the PLCs oper-
ate with ± 5 V DC and hence the power supply module converts the power
line voltage (120 V AC/240 V AC) to the required DC signal with various
circuitries as shown in Figure 2.7.
However, to prevent loss of programs from volatile RAMs when the
power supply goes off due to supply breakdowns, usually a power backup
in the form of uninterruptable power supply (UPS) is used in the PLC to
provide power. Usually rechargeable lithium-ion battery is used in such
cases, which can provide the required backup for several years. Recently
FIGURE 2.7 PLC power supply module.

large capacitors are also used to provide power backup but such backups are
limited to seventy-two hours.
• Program and data memory: Program memory stores the program used
by the microprocessor for generating the control actions depending on the
input. It is the library where the application program is stored. Process data
from the input modules and control data from the output modules are tem-
porarily stored in data memory as data tables. An image of these data tables
are used by the CPU. There are several memory elements in a PLC system
as shown in Figure 2.8.
• Read only memory (ROM) provides permanent storage for the operat-
ing system and fixed data used by the CPU.
• Random access memory (RAM) is provided for the user’s program and
data. Programs and data in RAM can be changed by the user. A portion
of the RAM is used to store the status of the input and output devices,
the values of the timers and counters, and other internal devices.
• There is a provision to incorporate an electrically erasable and pro-
grammable read-only memory (EEPROM) for user programming.
• Input and output modules: Input module is used to provide the interface
between the PLC and the input devices (sensors, switches, etc.). Every input
point has a unique address and the status or information available at the
inputs can be read by the CPU of the PLC. To protect the CPU, every input
is electronically isolated (by opto-isolator) and all the inputs on a single
module have similar circuitry for handling identical nature of inputs.
Output module is used to interface between the PLC and the output
devices (relay, triac, etc.). After the inputs are received by the CPU, it exe-
cutes the program and provides the status to the output points. Isolation is
provided between the CPU and the output devices. Choice of the output
module depends on the specifications (i.e., current and voltage rating) of
the output actuator. Similar to the input module, a single output module has
similar output circuitry for handling similar type of actuators.
FIGURE 2.8 Program and data sections of PLC RAM.

• Buses: In PLC architecture, a number of buses exist, which carry data and
control signals. The buses are the paths used for communication within
the PLC. The CPU buses are: data bus, address bus, and control bus. The
system bus is used for communication between the PLC and the external
I/O devices through I/O ports.
2.2.2 Central Control Unit of PLC

CPU structure of the PLC is shown in Figure 2.9.
ROM is interfaced with the control section consisting of control unit, ALU, and
internal registers. Control section of the PLC determines which part of it is to stay
functional, in which sequence, and for what duration.
The input scan block scans the inputs and places the individual input statuses in
RAM. After analysis and user program execution by control section, the logic scan
updates the output scan block to the appropriate state. Subsequently, the outputs are
scanned and updated depending on the output status signals of the CPU. Keyboard
is connected to the CPU for user programming and the status can be displayed in
display unit. For larger systems, communication can be made with other PLC CPUs
and PCs, if required.
2.2.3 Functional Modes of PLC

There are three functional modes of PLC: program mode, monitor mode, and run
mode.
FIGURE 2.9 CPU structure of the PLC.

• Program mode: In program mode, the operation of CPU is stopped. User

programming can be created or modified, memory can be cleared, pro-
grams can be checked, debugged, and I/O memory tables can be created
or modified.
• Run mode: It is used for normal system operation. The operating sta-
tus of the CPU can be monitored; however bits cannot be forced to set/
reset, present values and set values cannot be modified using program-
ming devices.
• Monitor mode: In this mode, the CPU remains functional; I/O is processed
in the same way as in run mode. The operating status of the CPU can be
monitored, bits can be forced to set/reset, the set values and present values
of timer and counter instructions can be modified, and the present values of
word data can be modified also. Monitor mode is used for necessary debug-
ging during trial operation.
Other than these three modes, there is another mode called remote mode. This mode
provides remote access of the PLC from a master PC. Remote mode is effective
when the PLC is in a location not easily accessible. The operating mode can be
changed using a programming device or by sending a command using Host Link
communications.
2.2.4 PLC Program Structure and Execution

Programming a PLC can be done in several ways, but in almost all cases program
structure consists of individual, separately defined sections which are executed in
sequence. These sections are called ‘blocks’ containing statements. The blocks are
functionally independent and are assigned with a particular (technical) function,
which has clearly defined and simple interfaces with other blocks yielding a clear
program structure. Various types of ‘blocks’ are available according to the function
of the program section.
In general, the major part of the program is contained in blocks that contain the
program logic in graphical format. For improved modularity, these blocks can be
called in a sequence or in nested configurations. Special function blocks are used to
realize both frequently used or complex functions, and these blocks can be ‘param-
eterized’. Similarly, individual steps of a control sequence can be programmed into
such a block and reused at various points in a program. With adequate expertise, the
user can produce own function blocks. Users can also define separate data blocks for
special purposes, such as monitoring, trending, etc., and perform read/write on such
areas. Such facilities of structured programming result in programs which are easier
to read, write, debug, and maintain.
There are different ways and means of executing a user program. Normally a
cyclic execution program is preferred and it is known as ‘PLC Scan Cycle’. The time
required by the PLC to complete one cycle is known as the ‘Scan Time’. After all
rungs have been scanned, the PLC starts all over again from the first rung. Of course
the scan time for a particular processor is a function of the processor speed, the
number of rungs, and the complexity of the user program.
FIGURE 2.10 PLC scan cycle.
• Scan time: How fast a PLC can perform a task is defined by the term ‘scan
time’. It is defined as the time required by a PLC (basically CPU) to acquire
the input status, to execute the application program, to provide updated
signals to the output devices, and lastly for self-diagnostics and commu-
nication. For PLCs used in process control applications, scan time usually
varies from 50 milliseconds to 0.1 second per 1K (1024) words. Thus, it is a
cyclic process consisting of four steps as shown in Figure 2.10.
During input scan, data in the input status table is read by the user
program when program is executed and the output status table is updated
accordingly. Data associated with output status table is transferred to output
terminals and in the last phase of the cycle, CPU performs self-diagnostics
as well as communication with host computer or any other devices con-
nected to the PLC.
The input status is updated during input scan and likewise, output
status is updated during output scan. After input scan, input image is
fed to the program execution section. During program execution, pro-
gram scanning takes place from left to right (rung scanning, usually fol-
lowed in Allen-Bradley PLC) or from top to bottom (column scanning,
followed by Modicon/Schneider PLC) across each rung. Figure 2.11a
(a) (b)
FIGURE 2.11 (a) PLC rung scanning. (b) PLC column scanning.
and Figure 2.11b show the manner in which PLC rung scanning and
column scanning are done.
• Interrupt-driven and clock-driven execution modes: A program run-
ning cyclically can be interrupted if put in an interrupt-driven mode of
program execution when fast reaction time is required. For an interrupt-
ing signal occurring at fixed intervals, a time synchronous execution is
implemented, i.e., with closed-loop control function. The cyclic execu-
tion, synchronized by a real-time clock, is the most common program
structure for a PLC.
2.2.5 Programming Devices for PLC

Various programming devices are available for use with PLCs to write, edit, and
monitor a program. It is also used to perform different diagnostic procedures.
Programming devices can be connected to a PLC either through online or offline
mode. Programming devices are connected to the CPU during programming in case
of online mode. In offline mode, a user can develop programs which can be down-
loaded when required. Programs can be developed in ladder logic or in any other
programming language.
Programming devices, usually known as program loaders, are classified into
three different forms: handheld, i.e., palm size units with dual function keypads and
smaller liquid crystal display (LCD) screen, full size programmer with full size key-
board and large LCD screen, and the third option is to develop programs in a stan-
dard PC. PC-based PLC programming is more convenient as software are provided
with PLCs with a number of menus, and programming can be done in offline and
tested before downloaded to the PLC.
2.2.6 Selection of I/O Modules for PLC – Sourcing

and Sinking
During the selection of I/O modules for a PLC, the concept of sourcing and sinking
should be very clear to a user. The concept of sourcing and sinking is related to
only DC circuits where the direction of current flow is defined. Figure 2.12(a)
and Figure 2.12(b), respectively, show the sourcing DC output module. Similarly,
Figure 2.12(c) and Figure 2.12(d), respectively, show the sinking DC input module. In
Figure 2.12(a) ‘Load 1’ is not connected to the PLC, whereas in Figure 2.12(b) ‘Load 1’
is connected, and hence current flows through it from PLC output module to the ground.
Similarly, in Figure 2.12(c), field contact is open and once it is closed (Figure 2.12(d))
current flows from external source through the field contact to the PLC input module.
If the PLC input or output module provides current for any input or output device, then
PLC is considered to be as sourcing device. Alternatively, if external supply is required
to provide current for PLC input or output modules then the PLC is considered to be a
sinking device. The most common form of the PLCs has sourcing output module and
sinking input module.
(a) (b)
(c) (d)
FIGURE 2.12 (a) Sourcing DC output module with ‘Load 1’ is not connected to the PLC,
(b) Sourcing DC output module with ‘Load 1’ is connected to the PLC. (c) Sinking DC input
module with field contact is open, and (d) Sinking DC input module with field contact is closed.
2.3 PLC PROGRAMMING TOOLS

2.3.1 Programming Languages
LD is the most popular form of PLC programming languages. Simplicity and easy
understanding are the key reasons for the wide acceptance of LD. Except LD other
PLC programming languages are – Mnemonic Instructions (MI), SFC, ST, Function
Block Diagram (FBD), IL, etc.
• Ladder Diagram: LD is also known as ladder logic which mimics the relay
logic used for batch processes. Due to its simple understanding (i.e., mini-
mum training is required) this programming language has become most
popular for the plant technicians.
• Mnemonic Instructions: MI is a set of machine-level instructions
(commands for microprocessor) are used for programming. These instruc-
tion sets can be directly derived from the ladder logic diagram.
• Sequential Function Charts: SFC is a flowchart-like programming tech-
nique with multiple paths but is more powerful than MI.
• Structured Text: ST programming language is nearly similar to high-level
PC programming language like PASCAL. It is very flexible and intuitive to
develop complex programs.
• Function Block Diagram: FBD programming technique is similar to

the block diagram representation where each block performs specific
function.
• Instruction List: In case of IL a list of instructions is provided by the
manufacturer for developing the PLC program. Each instruction is pro-
vided in a new line. An instruction consists of an operator followed by
one or more operands.
2.3.2 IEC 61131-3 Structuring Resources

At the early stage of PLC programming there was no standard. Manufacturers used
to develop their own programming techniques and hence users faced difficulties
if they intended to change their existing PLC programs. To overcome this limita-
tion, an international standard was adopted in December 1993 by International
Electrotechnical Commission (IEC). At present, this standard is defined as IEC
61131-3, which deals with basic software architecture and programming languages
of the control program for PLC. It defines two graphical and two textual program-
ming language standards:
• Ladder diagram – graphical

• Function block diagram – graphical
• Structured text – textual
• Instruction list – textual (deprecated in 3rd edition of the standard)
• Sequential function chart – graphical and textual. It has elements to orga-
nize programs for sequential and parallel control processing.
One of the primary benefits of the standard IEC 61131-3 is that it allows multiple
languages to be used within the same programmable controller. This allows the pro-
gram developer to select the language most well-suited for each particular task.
2.3.3 Ladder Diagram

To understand LD, let us consider a simple electrical circuit as shown in Figure 2.13a
depicts conventional electric circuit for motor On-Off control. If the switch is closed,
(a) (b)
FIGURE 2.13 (a) Conventional electric circuit for motor On-Off control. (b) Ladder
Diagram for motor On-Off control.
FIGURE 2.14 Physical wiring and ladder diagram for motor connection.
the motor gets the power. Figure 2.13b is the equivalent Ladder Diagram representa-
tion of Figure 2.13a.
In Figure 2.13b, vertical lines L1 and L2 are known as power rail. Here, L1 is con-
sidered to be a source and L2 is considered to be a sink. The horizontal line is known
as rung, which represents the control portion (switch is connected) of the circuit.
Hence, in LD representation emphasis is provided only on the control technique
rather than on the physical wiring.
Figure 2.14 is a more realistic presentation of PLC LD for a motor On-Off
operation. By energizing the input contact (IN001, normally open, i.e., NO con-
tact), relay (CR001, normally open) gets energized and closes the motor circuit
to turn it On.
Figure 2.15a is an extension of the previous motor On-Off operation with a start-
stop-hold arrangement. To start the motor, ‘Start’ button is pressed to energize the
motor starter coil and it also energizes the ‘Hold’ contact to keep the motor On even
after releasing the ‘Start’ button. To make the motor stop, we have to press the ‘Stop’
button to disconnect the supply of control power to the motor starter coil, which also
results in the release of the ‘Hold’ contact. If there is a failure of control power (mal-
functioning of source power of L1) then also the motor goes Off. Even after resuming
the control power, motor will not start unless the ‘Start’ button is pressed, and this
provides a safety feature to the motor operation.
In case of PLC LD of Figure 2.15b, by energizing the NO contact IN001, control
relay CR001 gets energized, which further energizes the NO contact CR001 to make
the motor On. Now, to stop the motor, NC contact IN002 needs to be energized to
disconnect the source power from control relay CR001 which further de-energizes
(a) (b)
FIGURE 2.15 (a) Conventional electric circuit for motor On-Off-Hold control. (b) Ladder
Diagram for motor On-Off-Hold control.
(a) (b)
FIGURE 2.16 (a) Conventional electric circuit for motor On-Off-Hold with forward and
reverse control. (b) Ladder Diagram for motor On-Off-Hold with forward and reverse
control.
CR001 contact. Here, in case of conventional electrical relay circuit (Figure 2.15a)
‘Hold’ contact is physically connected to the starter relay coil of the motor, i.e., it gets
energized or de-energized with the relay coil. But, in case of PLC LD, ‘Hold’ contact
(NO contact CR001) is internally realized by the PLC logic and it gets energized or
de-energized along with the relay coil CR001.
In Figure 2.16a, we have the facility to rotate the motor in forward (FR) and
reverse (RV) direction as per our requirement along with On-Off-Hold facility.
Before changing the direction of rotation we have to press the ‘Stop’ button. To start
the motor in forward direction, ‘FR’ button is pressed which energizes the ‘FR’ relay
coil and the hold contact ‘FR1’. It also de-energizes the hold contact ‘FR2’ to pre-
vent any chance of motor rotation in reverse direction. Similarly, starting of motor
in reverse direction can also be realized. Here, interlocking arrangement is provided
in between ‘FR2’ and ‘RV2’ so that both the output relays ‘FR’ and ‘RV’ can’t be
energized simultaneously.
Figure 2.16b depicts the similar PLC LD as with Figure 2.16a, but in a simpler
way. To start the motor in forward direction, NO contact IN002 needs to be ener-
gized, which results energizing of relay coil CR001. Consequently, energizing of
NO hold contact CR001 will make it close and NC hold contact will be open to
ensure forward motion of the motor and to prevent any chance of reverse motion (NC
contacts CR001 and CR002 are interlocked). To stop the motor, NC contact IN001
needs to be energized to cut the power supply to the relay coil. Similarly, to start the
motor in reverse direction, NO contact IN003 needs to be energized, i.e., to close,
which results in energizing relay coil CR002. Similar to the previous case, it causes
energizing of NO hold contact CR002 to make it close and NC hold contact CR002
will be open.
Here, in the preliminary discussion we have discussed with a single phase motor
but in actual industrial applications single phase motors are rarely used for direction
reversal. Moreover, before starting the motor in the reverse direction certain amount
of time delay is required to be provided to make the rotation stop for the connected
load, otherwise, it may cause mechanical stress which leads to the chances of actua-
tor failure.
2.3.4 Variables and Data Types

For industrial applications of PLC, it needs to handle various types of data. Any
form of data (bit, byte, word, double word, etc.) is referred by a variable name.
Variables are the nouns of any programming language and they are the entities
(data) which act or being acted upon. The type of a variable determines the nature
of data that the variable can have and the operations that can be performed on it.
PLC keeps all of its data in the register, which is basically a memory location that
provides temporary storage of data. Depending on the nature of the data, PLC
provides either single or group of registers. In PLC operation, data can be of vari-
ous types and as per standard architecture fundamental data types are described
by Figure 2.17.
Bits: Can have values 1 or 0. 1 typically represents ON while 0 represents

OFF. Bits are the building blocks for all other types of data.
Integers: Whole numbers (no decimal points) used to represent characters
(char), integers (int), long integers (long int), or words. Unsigned integers
are positive numbers, while signed are positive or negative.
Floating point numbers: Numbers with decimal points, which can be positive
or negative, and their larger variety is called double floats.
To represent positive or negative numbers, MSB is used. If MSB is 1 then it defines

negative number and if it is 0 then it signifies positive number.
2.3.5 Register
PLC registers are the memory locations that provide temporary storage of data.
Inside the PLC CPU there are two types of registers – internal registers and exter-
nal registers. Users usually do not have access to the internal registers, which
are 4, 8, 16, or 32 bits depending on the choice of the processor. Commonly
found internal registers are – accumulator register, data register, condition code
FIGURE 2.17 Various data types in PLC operation.

register, scratch pad register, instruction register, etc. All these registers help to
carry out the arithmetic and logical operations as per the programmed instruc-
tions. Registers are also used to store the time count value for Timer and Counter
functional blocks of a PLC.
External registers are the part of CPU’s RAM, usually of 16 bits and used to
hold variable information. Their size varies depending on the PLC structure and
programming capabilities. Commonly found external registers are – holding regis-
ters, input registers (single or group), and output registers (single or group). Holding
register holds the content of calculation related to arithmetic and logical operations.
As an example for an arithmetic operation, two holding registers contain the two
operands and another holding register contains the destination location of the result.
Input registers are readily accessible to the input modules to store the input status.
Usually, input group register can store 16 bits status of the input terminals. Similarly,
output registers are used to store the status of the output modules (usually 16 bits for
output group register) and the number of output registers is equal to the number of
input registers for a PLC.
2.3.6 Timer
Timer is an important function block for PLC. In various industrial applications
we need to run a process for a certain time interval such as oven temperature,
which must attain the desired value before we place the material into it, and this
is a typical application of On Delay Timer. On the contrary, Off Delay Timer can
keep the cooling fan ON for a predefined time interval after the oven has been
turned off. Before making the output ON or OFF, Timer counts the predefined
time interval in seconds or fraction of seconds using the internal CPU clock of
the PLC.
Depending on the manufacturer, Timers have different forms. Usually we con-
sider Timer output as a relay coil which when energized results in the closure or
opening of the contacts after some predefined time interval. Timers can be usually
classified as – On Delay Timer (non-retentive and retentive), Off Delay Timer, and
Pulse Timer.
2.3.6.1 On Delay Timer

Schematic diagram of an On Delay Timer is given in Figure 2.18.
Timer output becomes ON after the time delay provided as preset value. T-ON
accumulates time from the instant it is enabled until either the timer is disabled (i.e.,
IN is low) or the timer completes Preset Time (PT). Option is available to select PT
among different time bases – 1 ms, 10 ms, 100 ms, 1 s, etc.
LD is shown in Figure 2.19 with On Delay Timer.
Once the input (I:007) is enabled, enable bit (EN) becomes 1. After the PT delay
(PRESET 4 s) is elapsed, done bit (DN) becomes 1, which in turn makes the contact
T5:0 closed (NO to NC) and it results in energizing output O:009. While setting
timing, if input (I:007) becomes 0 (for any reason) after resuming the input (I:007
becomes 1) it can’t retain the time value elapsed and hence this type of timer is
known as non-retentive timer.
FIGURE 2.18 Schematic diagram of an On Delay Timer. (Courtesy: Automation Manual,

Rockwell Automation)
BOOL: Boolean I/O, i.e., On/Off
IN: Input
Q: Output
PT: Preset Time Input
ET: Elapsed Time Output
In case of retentive On Delay Timer, basic operational scheme is identical with

non-retentive On Delay Timer but here Timer can retain the value (i.e., doesn’t reset)
of elapsed time and starts accumulating once the input resumes (i.e., becomes high).
So, this type of Timer is useful to calculate the total running time of an instrument
for its scheduled maintenance.
2.3.6.2 Off Delay Timer

Schematic diagram of an Off Delay Timer is given in Figure 2.20.
Timer output becomes OFF after the time delay provided as preset value. T-OFF
accumulates time from the instant it is enabled until either the timer is disabled
(i.e., IN is low) or the timer completes PT. LD with Off Delay Timer is shown in
Figure 2.21.
(a) (b)
FIGURE 2.19 (a) Ladder Diagram and (b) timing diagram with On Delay Timer of an
industrial PLC. (Courtesy: Automation Manual, Rockwell Automation)
FIGURE 2.20 Schematic diagram of Off Delay Timer. (Courtesy: Automation Manual,
Rockwell Automation).
BOOL: Boolean I/O, i.e., On/Off
IN: Input
Q: Output
PT: Preset Time Input
ET: Elapsed Time Output
Once the input (I:009) is disabled, T-OFF starts timing. After elapsing of the PT
delay (PRESET 6 s), DN becomes 0, which in turn makes the contact T7:0 closed
(which is NC) and it results in energizing output O:011.
2.3.6.3 Pulse Timer

Pulse Timer is a special type of timer to keep output high (i.e., 1) for a fixed duration.
Operation of a Pulse Timer can be realized with a LD involving an On Delay Timer
(T-ON) as shown in Figure 2.22.
So, the ‘Output’ (CR:025) remains high for specified duration, i.e., during the
pulse On time.
(a) (b)
FIGURE 2.21 (a) Ladder Diagram and (b) timing diagram with Off Delay Timer of an
industrial PLC. (Courtesy: Automation Manual, Rockwell Automation).
(a) (b)
FIGURE 2.22 (a) Ladder Diagram and (b) timing diagram for Pulse Timer operation using
On Delay Timer.
2.3.7 Counter
Counter function is used in PLC for counting the number of events in terms of
transitions (pulses) from low to high or from high to low. In case of Up Counter,
every transition increases the count value whereas in case of Down Counter, it
decreases the count value, and once the specified count value is reached (preset
value for Up Counter and zero for Down Counter), output of the counter switches
to high/low. Typical industrial application of Counter involves counting of objects
in production line.
2.3.7.1 Up Counter
Up Counter (CTU) counts upward each time input to the counter switches from low
to high. As the count value reaches preset value, output of the Counter switches
to high and it remains high until it gets reset. Operation of Up Counter with LD is
shown in Figure 2.23.
(a) (b)
FIGURE 2.23 (a) Ladder Diagram and (b) timing diagram for Up Counter.
2.3.7.2 Down Counter

Down Counter (CTD) (Figure 2.24a) counts downward each time input to the
Counter switches from low to high. As the count value reaches zero from the preset
value, DN of the Counter switches to low and it remains low until it gets reset.
2.3.7.3 Up-Down Counter

Both up counting and down counting operations can be done by a single Counter
known as Up-Down Counter (CTUD) (Figure 2.24b) where input (switching from
low to high) at the Up Counter input causes increment of count; similarly input
(switching from low to high) at the Down Counter input causes decrement of the
count value. This type of operation is very useful for having net count value, e.g.,
in automatic car parking facility where always some car is leaving and some car is
entering. Hence, the resultant count value is required to be calculated and once it
reaches the limit then the display ‘Parking Full’ is made to be ON.
2.3.8 Arithmetic Function
Depending on the manufacturer, most of the PLCs contain a number of arithmetic
operations – ADD (addition), SUB (subtraction), MUL (multiplication), DIV (division),
SQR (square), SQRT (square root), NEG (negative), ABS (absolute), etc. Usually, the
arithmetic functions operate only when the block is enabled (i.e., low to high). If the
Enable input remains high, then nothing will happen. Repetitive clock is required for
continuous arithmetic operation, e.g., repetitive adding and similarly for others.
2.3.8.1 Addition (ADD)

If input (I:007) is enabled, numeric value of source B (register) is added to the
numeric value of source A (register) and the result is stored in the destination
(a) (b)
FIGURE 2.24 Symbolic representation of (a) Down Counter and (b) Up-Down Counter.
CD: Down Counter Input, LD: Load Value
PV: Preset Value, CV: Count Value, Q: Output
CU: Up Counter Input
QU: Up Counter Output, QD: Down Counter Output
FIGURE 2.25 Ladder Diagram representation of ADD operation.
register. If the addition process (Figure 2.25) results in a value which causes
either negative value or overflow of the destination register then output coil
(ADD:005) gets energized.
2.3.8.2 Subtraction (SUB)

Subtraction (SUB) operation (Figure 2.26) is almost similar to addition (ADD) oper-
ation. In counting applications of industrial production line, ADD and SUB func-
tions are quite popular.
If input (I:009) is enabled, numeric value of source B (register) is subtracted from
the numeric value of source A (register) and the result is stored in the destination
register (Figure 2.26). If the subtraction process results in a negative value, result-
ing value is stored in the destination register and the output coil (SUB:007) gets
energized.
If input (I:011) is enabled, numeric value of source B (multiplier) is multiplied
with the numeric value of source A (multiplicand) and the result is stored in the
destination register (Figure 2.27). Output coil (MUL:009) gets energized once the
multiplication is over.
Usually, squaring operation in a PLC is performed by providing the same input
in source A and source B and hence the corresponding square value appears in the
destination (two registers).
2.3.8.3 Division (DIV)

If input (I:013) is enabled, numeric value of source A (dividend) is divided
(Figure 2.28) by the numeric value of source B (divisor) and the division result is stored
in the first destination register. Remainder is stored in second destination register.
FIGURE 2.26 Ladder Diagram representation of SUB operation.

FIGURE 2.27 Ladder Diagram representation of MUL operation.
Modulo (MOD) is a special class of division process where the content of source A is
divided by the content of source B and the remainder is stored in the destination register.
2.3.8.4 Square Root (SQRT)

If input (I:015) is enabled, square root value of the numeric value of source is stored
in the destination register (Figure 2.29). Usually, destination register contains only
the nearest integer value.
In addition to the previously described functions, a number of other arithmetic
functions are available in midsized PLCs as provided in Table 2.3.
For more precise arithmetic operations, some PLCs have the double-precision
feature, which provides more accurate results required for some specific applica-
tions. Comparison functions are also considered to be an extension of the basic arith-
metic functions. In comparison function, two numbers are compared to check which
one is greater (smaller) or equal to the other. Usually, PLCs contain the comparison
functions shown in Table 2.4.
The above functions other than MEQ and LIM are described in Figure 2.30.
If input (I:017) is enabled, two numbers provided in source A and source B is
compared. If they are equal then the output coil (EQU:015) goes On.
Similar operation takes place for NEQ, LES, LEQ, GRT, and GEQ.
2.4 ADVANCED PLC FUNCTIONS

2.4.1 Data Handling Functions
Data handling functions of a PLC mainly involve movement of data from one place
to another. In its simplest form, content of a register can be moved from one to
other register by a function known as MOVE function. Alternatively, data from two
FIGURE 2.28 Ladder Diagram representation of DIV operation.

FIGURE 2.29 Ladder Diagram representation of SQRT operation.
TABLE 2.3
PLC Arithmetic Functions
Function Description
SIN Sine value of the angle in degree
COS Cosine value of the angle in degree
TAN Tangent value of the angle in degree
ASIN Arc Sine value of the angle in degree
ACOS Arc Cosine value of the angle in degree
ATAN Arc Tangent value of the angle in degree
DEG Convert angle value from Radian to degree
RAD Convert angle value from degree to radian
LN Compute Natural Logarithm of the given value
LOG Compute Logarithm to base 10 of the given value
XPY Compute X to the power of Y
CPT Compute a user defined formula
AVE Compute average value of a series on numbers
STD Compute standard deviation of a series on numbers
NEG Perform negation of the given number
ABS Provide absolute value of the given number
TABLE 2.4
PLC Comparison Functions
Function Description
EQU Test whether two numbers are equal
NEQ Test whether one number is not equal to a second number
LES Test whether one number is less than a second number
LEQ Test whether one number is less than or equal to a second number
GRT Test whether one number is greater than a second number
GEQ Test whether one number is greater than or equal to a second number
MEQ Test whether a portion two numbers are equal through masking
LIM Test a number whether it lies between an upper and lower limit
FIGURE 2.30 Ladder Diagram representation of EQU operation.
or more consecutive registers can be transferred to other two or more consecutive

registers, which is called BLOCK TRANSFER (BT). There is another type of data
movement where data moves sequentially from a specified portion of a large listing
of data to a single register (TABLE TO REGISTER (TR)). Conversely, data can
move sequentially from a single register into a specified portion of a table of regis-
ters (REGISTER TO TABLE). In all forms of data movement, content of the source
register/registers remains unchanged.
2.4.1.1 MOVE (MV)

Figure 2.31 shows a MOVE function.
By enabling the input (I:007), content of the input register IR0011 is moved to the
destination register OR0122, and on completion of the data movement, function coil
(MV0012) goes ON.
MOVE function can be used to move a preset value to a Timer or Counter, or
a Timer or Counter value to some Register for storage, or data from an Input to a
Register or from a Register to Output.
2.4.1.2 BLOCK TRANSFER (BT)

The BT function is shown in Figure 2.32.
By enabling the input (I:009), content of 10 consecutive Registers (the last Register
being IR0021) is moved to 10 consecutive destination Registers (where the last Register
is OR0123). On completion of data movement, function coil (BT0022) goes ON.
2.4.1.3 TABLE AND REGISTER MOVE

In case of TR Move function, data moves sequentially from a specified number of
Registers to a single Register and is shown in Figure 2.33.
FIGURE 2.31 MOVE function.

FIGURE 2.32 BLOCK TRANSFER function.
By energizing the Enable input (I:013) and while Reset input (I:012) is turned off,
as the Step input (I:011) is enabled, data moves from the specified Register (indicated
by the pointer) with consecutive 5 locations (where the last Register is OR0031) to
the destination Registers (HR0163). On completion of the data movement, function
coil (TR0023) goes ON. A Timer contact may be used as the step contact for the
function.
Conversely, in case of REGISTER TO TABLE move function, data moves
sequentially from a single Register to a specified number of consecutive Registers,
known as Table, and is shown in Figure 2.34.
By enabling the input (I:017) and while Reset input (I:016) is turned off, as the
Step input (I:015) is enabled, data moves from the source Register (HR0173) to 7
consecutive Register locations (indicated by the pointer) where the last Register is
OR0061. On completion of data movement function coil (RT0025) goes ON. As an
example, the changing value of a process parameter stored in Source Register is
sequentially transferred to a number of Destination Registers termed as Table.
2.4.2 Matrix Functions
In PLC programming when a large number of bit status need to be scanned and
thereafter some logic operation is required to be performed, Matrix function of
PLC is preferred over conventional LD. LD technique requires a lot of memory
FIGURE 2.33 TABLE TO REGISTER move function.

FIGURE 2.34 REGISTER TO TABLE move function.
space and the execution speed is low because of the need to handle a large num-
ber of I/Os. PLC Matrix operation deals with one or two matrices and it results
in another matrix.
As an example, if 100 relay coils need to be energized depending on the input
status of 200 switches (NO/NC) where the logic is so defined that each relay coil will
be energized if both the input contacts (connected to it) are closed. If conventional
ladder logic is used, a LD with 100 lines need to be drawn as shown in Figure 2.35a,
while the convenient Matrix function is shown in Figure 2.35b.
A single line LD defining the Matrix function is all that is needed to use matrix
operation in PLCs. The Matrix function will contain two matrices (Matrix 1 and
Matrix 2) each having 100 logical elements (i.e., 1/0), and an AND operation is per-
formed between the corresponding elements of the two matrices. Resulting output
status will be stored into another matrix and its content is used to energize the output
relay coils. In actual practice, input data or status (i.e., the content of Matrix 1 and
Matrix 2) is stored in two separate series of Registers. And the output is stored in
(a) (b)
FIGURE 2.35 (a) Conventional Ladder Diagram. (b) Matrix function.

(a) (b)
FIGURE 2.36 (a) NAND and (b) NOR realization by combining Matrix functions.
another series of Registers, called Output Registers. Logical OR and XOR opera-
tions can also be performed on the matrix elements.
PLC Matrix function can be utilized to perform COMPLEMENT as well as
COMPARE operations. In case of COMPLEMENT, logical status of the register
content (i.e., each matrix element) is replaced by their respective complement values.
In case of COMPARE function, logical status of the two corresponding bit positions
of two matrices are compared and if they are identical, then output is 1, otherwise
it will be 0.
By combining the PLC Matrix functions AND and COMPLEMENT, NAND
operation can be realized. Here, first AND operation is performed for two matri-
ces and the resultant matrix is subsequently COMPLEMENTed to realize NAND
operation. NOR operation can be realized by combining OR and COMPLEMENT
functions as shown in Figure 2.36.
2.4.3 Analog Signal Handling

Modern PLCs can deal with the analog signals with their analog input and out-
put modules. Before the analog signal, obtained from sensors, is fed to the input
module of the PLC, proper signal conditioning is required so that its variation
from minimum to maximum value matches with the input signal range of the
PLC analog input module. Analog module converts the analog signal into digital
format.
FIGURE 2.37 Analog signal handling by a PLC.
Here, it is assumed that the analog signal varies linearly throughout the entire
range. Similarly, for driving an analog actuator, PLC can provide analog output
from the analog output module. This module converts the digital output produced
by the PLC into analog signal. Depending on the nature of the input and output
signals (i.e., voltage or current), various analog I/O modules are available with the
PLC with different current and voltage ratings. An isolation circuit protects the
analog I/O modules of the PLC. How a PLC handles the analog signal is shown
in Figure 2.37.
In Figure 2.37, analog signal (output from the sensor) is fed to the PLC for divi-
sion operation by 2 and the resultant output analog voltage is fed to an actuator after
required signal conditioning. Thus, analog signal can be fed to the PLC for required
arithmetic or logical operation before being fed to the actuator.
Selection of an analog input module for a PLC depends on several factors,
among them being voltage level and current magnitude of the input signal, speed
of conversion required, etc. Similarly, the choice of the analog output module for
a PLC is dependent on several factors like required voltage level for the actua-
tor, value of the load resistance, current driving requirement, and the speed of
conversion.
If two analog signals from two different sensors are to be added, proper signal
conditioning of both signals is done to match them with the analog input modules
of the PLC. After addition, the result is fed to the display device through an analog
output module as shown in Figure 2.38a and Figure 2.38b.
2.4.4 PID Control with PLC

Modern PLCs with PID function are presently being used in continuous closed-loop
control applications. This PID control function is nothing but an extension of the
analog signal handling feature of the PLC. Desired value or set point and the feed-
back signal from the process are fed to the PLC through analog input module. PID
control action produced by the PLC is fed to the actuator through an analog output
module. PID function is provided in the PLC as an algorithm where user has to pro-
vide the tuning parameters as well as various other settings. The PID function block
residing in a PLC is shown in Figure 2.39.
PID function is enabled by making the Enable input high. Set or desired value
for the control loop is stored in Register. Similarly, process variable as well as
(a)
(b)
FIGURE 2.38 Addition of two analog inputs by PLC.

Adds values of Input Registers IR0011 and IR0012 and stores the result in the Output Register OR0012
control variable, i.e., the control action, is also stored in Registers. The number
of Registers involved with PID function depends on the model and manufac-
turer. Control block setup contains the setting for the individual parameter of
the PID controller – proportional gain, reset time, rate time, set point max-min,
output max-min, dead band, scaling parameters, etc. Most of the parameters
of PID block are provided in percentage scale. On enabling the PID function,
Enable coil becomes ON and after computation of PID algorithm, ‘Done’ coil
becomes ON.
The role of cycle time is very crucial in PID function. Usually it is chosen as an
integral multiple of the Scan Time of the PLC. The cycle time of the PID algorithm
FIGURE 2.39 PID function block.

represents the time between two calculations of the output value (control value). The
choice of the value of cycle time is dependent on the dynamic behavior of the pro-
cess to be controlled. For a process with a fast dynamic response, cycle time should
be small enough to achieve the desired closed-loop controlling performance. On
the contrary, for processes with slow dynamic response, there is no such stringent
restriction on the choice of the cycle time for a PID controller. The user must have
sufficient knowledge to choose proper choice of the cycle time for an effective PID
control. In addition, a number of alarm functions are also available within the PID
block, which the plant personnel use as per their needs.
2.4.5 Digital Bit Function

Wide variations in operation can be achieved with the bits of a register in a PLC.
Instead of controlling output devices from individual contacts, register bits in a
group can be used for controlling multiple number of outputs. As an example, output
status of 16 LEDs (i.e., On or Off) can be controlled by the 16 bits of a PLC holding
Register as shown in Figure 2.40.
The bit-pick (BP) contact control scheme is used to control relay coils based
on the bit status of the Register as shown in Figure 2.41. Here, the BP function is
used to pick the status of the first, second, and third bits of the holding register
HR0004 to control the status of the relay coils CR0001, CR0002, and CR0003,
respectively.
To change the bit status of the Register (e.g., HR0004), three PLC functions – bit
set (BS), bit clear (BC), and bit follow (BF) are used. The BS function is used to set
any bit of the holding Register as shown in Figure 2.42.
By making the set contact IN0021 close, third bit of the HR0004 is set
irrespective of the previous condition. If the set contact IN0021 is kept in
de-energized condition, then there will be no change in the bit status and it would
remain in the condition that it was initially. Figure 2.43 shows the BC function is
used to clear the fifth bit of Register HR0004. BC function is opposite in nature
to BS function.
On enabling the clear contact IN0022, fifth bit of HR0004 will be clear (reset)
irrespective of the previous status of this bit. If the contact IN0022 is kept disabled,
then the previous status of the fifth bit of HR0004 will be maintained.
BF function is a little different from BS and BC functions. Here, the bit status of
the holding register follows the status of the input contact as shown in Figure 2.44.
If the input contact IN0023 is enabled (close) then sixth bit of the Register
HR0004 will be set, but if the input contact IN0023 is disabled (open) then sixth bit
of the Register HR0004 will be reset. So, the bit status of the Register follows the
input contact status.
FIGURE 2.40 A 16-bit Register containing a bit pattern.

FIGURE 2.41 BP function to control relay coil status.
FIGURE 2.42 Bit set (BS) function used to set 3rd bit of 16-bit Register HR0004.
FIGURE 2.43 Bit clear (BC) function used to clear 5th bit of 16-bit Register HR0004.
FIGURE 2.44 Bit follow (BF) function used to set/clear 6th bit of 16-bit register HR0004.
2.4.6 Shift Register Function

A number of Shift Register functions are available in PLC – shift left (SL), shift right
(SR), rotate left (RL), rotate right (RR), multiple shift left (MSL), and multiple shift
right (MSR). These functions can be used to change the contents of a single Register
or multiple number of Registers at a time. The SR function for one Register is shown
in Figure 2.45.
Operation of SR of Register HR0005 can be explained from Figure 2.45. Here,
input IN0024 is energized each time for one bit shifting. IN0025 is made on/off for
feeding bit 0/1 and IN0026 is used as Enable input. Thus, to change the bit status of
the entire Register, 16 times shifting is needed by feeding bit 0/1. In some versions
of PLCs, length of the Register can be specified for shifting, where only the specified
length of the Register will be shifted and the rest of the Register bit status remains
intact.
If modifications of the status of the bits for more than 16-bit locations are required
for some specific application, more than one 16-bit Register is needed. For such
cases, only the required number of bits are used and the rest of the bits are kept
unused as shown in Figure 2.46.
Here, 24 bits are involved in the SR operation and hence Register HR0006
and 8 bits of Register HR0007 are used. The rest of the eight bits of HR0007 are
not used.
Similarly, SL for single and multiple number of Registers can be performed.
In case of SL operation, new data bit (0/1) is fed from the right and the entire bit
pattern is shifted left. In some advanced versions of PLCs, multiple number of
bit shifting (right or left) can be done at a time and these functions are known
as MSR or MSL. These operations are also known as N-bit right shift (N-SR)
or N-bit left shift (N-SL). Here, the number of bits (N) to be shifted needs to be
specified. An example for MSL operation for three bits (i.e., N = 3) is shown in
Figure 2.47.
FIGURE 2.45 Shift right (SR) function for one Register.

FIGURE 2.46 Shift right (SR) function for two Registers with 24 bits.
Another common function of the Register is the RR or RL option. In case of

rotate operation, entire or partial bit pattern of a Register is rotated either through
the right or through left direction of the said Register and no bit status is lost in
this operation. Figure 2.48 shows the RR operation for 8 bits at a time for an entire
Register.
Here, two Registers are involved in RR operation for 8 bits at a time, i.e., 8 bits
are moved simultaneously through the two Registers every time the input is ‘On’.
FIGURE 2.47 Multiple shift right (SR) operation for 3 bits at a time.
(a) (b)
FIGURE 2.48 Rotate right (RR) operation for 8 bits at a time with entire Register: (a) before
rotation and (b) after rotation.
This technique is very popular in designing moving displays where the same bit pat-
tern is repeated sequentially through the Registers.
Instead of using the entire bits of the Register, a part of the bit pattern can be
rotated, as shown in Figure 2.49. The unused bits of the Register are kept intact.
Similar operations can be done for RL with entire and partial use of Register.
2.4.7 Sequence Function

The sequencing function of a PLC is conceptually based on the operation of elec-
tromechanical drum switching mechanism. Electromechanical drum switches are
convenient for handling applications with fixed sequence and limited number of con-
tacts. But, to derive flexibility in sequence designing and to control large number
of contacts, PLC Sequence Function is more user-friendly and it is often termed
as drum controller. In sequence operation, multiple outputs can be controlled with
several bit patterns. Thus in every sequence step, the state of the output devices con-
nected to the output ports can be changed. Output can change from on to off state,
or vice versa, or remain in the same state. Well-known PLC manufacturers (like
Allen-Bradley) offer three Sequence Functions: Sequencer Output (SQO) function,
Sequencer Input (SQI) function, Sequencer Load (SQL) function, and Sequencer
Compare (SQC) function. The SQO function is shown in Figure 2.50.
(a) (b)
FIGURE 2.49 Rotate right (RR) operation for 8 bits at a time with partial use of Register
(a) before rotation (b) after rotation.
FIGURE 2.50 Sequencer Output (SQO) function.
SQO function data (on/off bit patterns) is stored in a file and the address of this
file location is stored in ‘File’ field. This bit pattern can be masked (if required)
by the hexadecimal code written in the ‘Mask’ field. ‘Destination’ file contains
the address of the output module where the SQO is to be moved. ‘Control’ reg-
ister is used for controlling and monitoring of the SQO function. The length of
the sequencer file is written in the ‘Length’ Register and ‘Position’ indicates
the current location of the word in the Sequencer File. This ‘Position’ value is
incremented internally after transferring the Register bit pattern from ‘File’. The
Enable (EN) coil is energized when the sequencer is On. The Done (DN) coil will
get energized when the sequencer has completed stepping through the number of
steps specified for the SQO function. Contacts with these coil addresses may be
used to turn On or Off PLC functions and/or PLC output devices. Reset (RES)
function associated with the ‘Control’ Register can be used to reset the SQO
function.
Here, manual push-button switch IN0017 is repeatedly pressed for generat-
ing logical high signal so that the SQO moves through the steps. But, instead
of using such push- button switch, the Timer block can be used to produce logi-
cal high input for SQO at a predefined regular interval. In order to have vari-
able time intervals between sequencer steps, a second sequencer is utilized. The
new sequencer file contains different integer values which will be loaded in the
accumulator of the Timer block to generate different time intervals instead of a
fixed value. Here, both sequencers must be synchronized to step through the pat-
terns simultaneously. Now, if more than 16 discrete outputs are to be controlled
simultaneously, two sequencers in parallel can be connected such that they step
through 32 defined patterns written in the file. This parallel operation of multiple
numbers of sequencers may be increased to control a large number of discrete
outputs. The SQL function is shown in Figure 2.51.
SQL (sometimes called SQI function also) is used to collect data from input mod-
ules. Figure 2.51 displays a ladder logic diagram that illustrates how to read the
input IN0019 and record the data in data file whose index address is provided in File
Register. Here, Timer block may be used in addition to read the input at a regular
interval.
FIGURE 2.51 Sequencer Load (SQL) function.
The SQC function, shown in Figure 2.52, is used to read an input IN0021, and
then it will compare the input data to the data stored in the Sequencer Data File. If
the collected data from the input module matches the data in data file (whose index
address is provided in the File Register), the bit found (FD) coil will get energized.
This logical change in FD may be used for any further action.
2.4.8 Function Chart to IEC 60848

SFC is a graphical programming language used in PLCs. It is one of the five lan-
guages defined by IEC 61131-3 standard utilized for PLC programming. The
SFC standard is based on GRAFCET (GRAFCET is a standard valid in Europe
(DIN EN 60848) which is used to describe a control function). This international
standard defines the behavior of the sequential part of a control system. This standard
specifies the symbols and rules for the graphical representation of this language, as
well as for its interpretation. This standard has been prepared for automated produc-
tion systems of industrial applications. The main components of SFC are:
• Steps with associated actions

• Transitions with associated logic conditions
• Directed links between steps and transitions
FIGURE 2.52 Sequencer Compare (SQC) function.

Steps in an SFC diagram can be active or inactive. Actions are only executed for
active steps. A step can be active for one of the two reasons:
• It is an initial step as specified by the programmer

• It is activated during a scan cycle
SFC is an inherently parallel language in that multiple control programs can be

executed at a time and hence quiet efficient for realization of industrial automation
processes through PLCs.
2.5 PLC COMMUNICATION

2.5.1 Necessity for PLC Communication
PLC communication lends an effective and efficient way for industries with large
number of I/O devices distributed over a large area to communicate with each other.
Moreover, PLC employed in one section of the plant needs to communicate with the
PLC employed for another section of the plant for smooth running of the production
process. In some cases, PLCs are connected to operator interfaces in the control
room for Graphical User Interface (GUI) facility.
By incorporating additional I/O modules, we can connect large number of I/O
devices through extension lines. Extension modules can have inputs and outputs of
different nature and they may be located considerably long distance away from the
PLC. For PLC to PLC communication, a number of PLCs may be linked together
with a master PLC which controls the data exchange from the connected PLCs.
This will help in sending process variable information and consequent data analy-
sis and trends to be made available at the management level for decision-making.
This is realized by connecting the PLCs to PCs at the operator interface level and
management information level. Data and control information flow horizontally and
vertically and are made possible with effective communication following established
protocols. Communication between the communicating devices is made possible
with the following:
• Physical connection between the communicating devices.

• Protocol, i.e., the common language which allows each device to under-
stand what the bits and bytes are in the communication messages.
Figure 2.53 shows how communication between Human-Machine Interface (HMI)

and I/O extension modules takes place.
In the early days, PLC communications were typically proprietary in nature with
each supplier having their own closed connections and protocols. This made com-
munication relatively simple for a single vendor’s products, but fails miserably when
communications between devices from different vendors are needed. Later, with the
advent of Open System Interconnection (OSI) model, proprietary connections were
dispensed with and a seamless connectivity between devices from different vendors
were made possible.
FIGURE 2.53 PLC communication with HMI and I/O extension modules.
2.5.2 Data Transmission Formats

There are different data transmission formats for transmission of data between PLCs,
PLC to HMI, and PLCs to I/O extension modules. Mostly it is serial communication
between the communicating devices. Data is encrypted before it is sent and at the
receiving end side, it is decrypted to get back the original data.
The most preferred serial standard for data communication is RS-232, the oth-
ers being RS-422 and RS-423. In communication with RS-232, devices may be
Data Terminal Equipment (DTE) and Data Communication Equipment (DCE).
Depending on the application, PLC can behave as either DTE or DCE. For example,
in case of communication between field instruments with PLC, the role of PLC may
be considered as DTE. Alternatively, if PLC communicates with PC (HMI), then the
role of PLC is identical to DCE.
Topologies used for connecting field devices with PLC may be peer-to-peer, star,
bus, etc. Choice of a particular topology depends on physical placement of devices,
cabling cost, data urgency, real-time operational constraint, data transfer rate, etc. In
case of peer-to-peer connection dedicated link is there for communication and hence
it is quite simple in terms of data flow management. But, in case of other topolo-
gies, protocols need to be defined for data flow management between PLC and field
devices. As a result a number of standard protocols like MODBUS RTU, EtherNet/
Internet Protocol (IP), Ethernet TCP/IP, MODBUS TCP/IP, etc. are supported
by PLCs.
2.5.3 Communication with Field Instruments

In plant automation network, field instruments (sensors and actuators) are connected
to the PLCs through I/O modules, along with signal conditioners, if required. When
data is to be transmitted in a fixed direction, i.e., for unidirectional data flow, simplex
mode of communication is employed. For bidirectional data flow, half duplex mode
of communication is preferred.
Cabling cost is a major issue for connecting a large number of dispersed I/O
devices with PLC. To reduce cost of cabling, PLC I/O modules are placed close to
the field instruments and the I/O module is connected to the PLC through exten-
sion cables. In case of peer-to-peer link, master-slave (poll-response) communication
technique is used to retrieve information from field instruments. Dedicated com-
munication link is available in case of peer-to-peer connection but it involves large
cabling cost. Star, ring, and bus topologies are also utilized by the PLC for commu-
nicating with field instruments. Standard protocols are always used for communica-
tion between the connected devices.
Communication between PLC and field instruments and others may be synchro-
nous or asynchronous. Synchronous communication is faster than asynchronous one
and is undertaken when huge data is to be transmitted on a regular basis at a very fast
rate. But in practice, in industrial communication, very fast data transfer rate is not
required and also data is intermittent in nature. Thus mostly, data is transferred via
asynchronous communication. Thus, in this case, synchronism between DTE and
DCE is not required and nodes can initiate communication as and when required.
Some popular asynchronous serial standards used in industries are RS-232, RS-422,
RS-485, Ethernet, MODBUS, DF-1, I2C, SPI, etc.
2.5.4 PLC Protocols

Industrial automation involves a number of protocols for communications with
PLCs. Choice of a protocol depends on the type of devices taking part in communi-
cation with PLC, i.e., between field instruments and PLC, PLC and host computer,
and PLC to PLC. Some of the protocols which are popular in industrial automation
are briefly discussed now:
• RS-232: In 1963, Electronic Industries Association (EIA) adopted a stan-

dard called ‘Recommended Standard-232’ (RS-232) to govern the inter-
face between the DTE and DCE employing serial communication. It is
the most versatile and widely accepted physical layer protocol. Electrical
interface of RS-232 is single ended and un-terminated. It uses single wire
for each signal which represents logic level of each signal with bipolar
voltage levels. Due to unbalanced transmission, noise problem is an issue
which limits the maximum length of the cable to 50 ft and maximum
data rate to 20 kbps. Asynchronous serial interface is used for peer-to-
peer connection where there is no ‘master’ or ‘slave’. RS-232 uses 25 or
9 pins connector with four categories of signals – common, data, control,
and timing. Voltage level between +5 V and +15 V defines logic ‘low’
and between −5 V and −15 V defines logic ‘high’ for the output signal.
Voltages between −5 V and +5 V is undefined to accommodate noise.
Voltage levels at the receiver input should be between +3 V and +15 V
to for logic ‘low’ (‘Mark’) and between −3 V and −15 V for logic ‘high’
(‘Space’), i.e., inverted logic is followed.
• RS-422: EIA adopted RS-422 standard in 1973, which is also known as
EIA-422 or EIA/TIA-422. It is a balanced or differential communication
interface to minimize the problem related to varying ground potential.
Due to differential transmission, noise signal is cancelled out as both the
conductors (running through the same environment) pick up identical noise.

It was designed to achieve larger distance and higher baud rate compared
to RS-232. RS-422 can communicate up to 4,000 ft and data transfer rate
can be up to 10 Mbps.
• RS-485: RS-485 is an upgraded version of RS-422 with same distance
and speed of communication but it allows up to 32 drivers and receivers.
RS-485 is defined as a multipoint bus where a line driver can operate in
three states – Logic 1, Logic 0, and high-impedance. If the differential volt-
age between line A and line B is −1.5 V to −6 V with respect to line B, it is
defined as 1 (‘Mark’), for +1.5 V to +6 V with respect to line B, it is defined
as 0 (‘Space’). In high impedance state, the device connected to the line
virtually draws no current and appears not to be present on the line. This is
known as a disabled state and can be initiated by a signal on a control pin
on the line driver circuit. Tristate operation allows a multi-drop network
connection.
• Ethernet: Ethernet was commercially introduced in 1980 by three organi-
zations (Digital Equipment Corporation, Intel, and Xerox) and later stan-
dardized in 1985 as IEEE 802.3. The Ethernet standards comprise several
wirings and signaling variants of the physical layer and till now it is vary-
ing to keep pace with technological advancements. The original 10 BASE
5 Ethernet uses thick coaxial cable as a shared medium. Later the coaxial
cables were replaced by twisted pair and fiber-optic links in conjunction
with hubs or switches. Data rates were periodically increased from the
original 10 Mbps to 10 Gbps. For accessing physical media, Carrier Sense
Multiple Access with Collision Detection (CSMA/CD) mechanism is most
widely used in Ethernet Local area Network (LAN). Ethernet CSMA/CD
standard has some hardware variations:
10 Base 2 (IEEE 802.3a, 1985): 10 Mbps, standard thin coaxial cable,
185 m
10 Base T (IEEE 802.3i, 1990): 10 Mbps, unshielded twisted pair
(UTP) cable, 100 m
100 Base F (IEEE 802.3j, 1993): 100 Mbps, optical fiber, 220 m
100 Base T (IEEE 802.3u, 1995): 100 Mbps, UTP cable, 100 m
1000 Base T (IEEE 802.3ab, 1999): 1,000 Mbps, Gigabit Ethernet,
UTP cable, 100 m
• MODBUS: MODBUS is an open protocol based on Application Layer, i.e.,
Layer-7 of OSI model. It is a messaging protocol that provides master-slave
communication between intelligent devices on different types of buses and
networks. It was developed by Modicon in 1979 as a structure of data repre-
sentation and is independent of the physical layer. Now, it is the most widely
used protocol for industrial manufacturing environment. MODBUS proto-
col defines the technique for access and control of one device by another
regardless of the type of physical network on which it is used. MODBUS
describes how information is received and queries are responded. Data link
layer and Physical layer of MODBUS use serial communication protocol
and RS-485 bus as Physical layer.
MODBUS devices communicate using a master-slave technique in

which only one device (i.e., master) can initiate transactions (through que-
ries). The other devices (i.e., slaves) respond by supplying the requested
data to the master, or by taking the action requested in the query. A slave is
any peripheral device (I/O transducer, valve, network drive, or other mea-
suring device) which processes information and sends its output to the mas-
ter using MODBUS. Masters can address individual slaves or can initiate
a broadcast message to all slaves. Slaves return a response to all queries
addressed to them individually but do not respond to broadcast queries.
MODBUS devices usually include a Register Map. MODBUS operation
(like monitoring, configure, and control module I/O) takes place depending
on the Register Map. An understanding of MODBUS operation requires a
thorough knowledge of the Register Map of the device.
• DF-1: It is an asynchronous byte-oriented protocol used to communicate
with most Allen-Bradley RS232 interface modules. DF-1 protocol consists
of data link layer and application layer of the OSI model. It works in half
duplex mode for master-slave communication and full duplex mode in case
of peer-to-peer communication. Half-duplex protocol is a multi-drop proto-
col for one master and one or more slaves. With half-duplex protocol, one
can have 2–255 nodes simultaneously connected on a single link, the link
operating with all nodes interfaced through half-duplex modems. One can
designate one node as master to control which node has access to the link.
All other nodes are slaves and must wait for permission from the master
before transmitting. Each slave node has a unique node number between 0
and 254. In case of slave-to-slave communication, the master looks at the
packet received from the slave. If the packet is not for the master, the mas-
ter reassembles the packet as a master packet and sends the packet to the
concerned slave device.
• I2C: I2C bus is a bidirectional two-wired serial bus which is used to trans-
port data between integrated circuits. Here, the name I2C stands for ‘Inter
Integrated Circuit’. It was first introduced by the Philips Semiconductors
in 1982. It is an inter system and short distance protocol, which means,
it is used within the circuit board to communicate the master and slave
devices. For PLC-based applications, it is usually used to communicate
between PLC and microcontroller. This bus supports 7-bit and 10-bit
address space device and its operation differs with low voltages. Two sig-
nal lines of I2C bus are SCL and SDL, which are used to communicate
with the devices. SCL stands for a ‘Serial Clock Line’ and this signal
is always driven by the ‘master device’. SDL stands for the ‘Serial Data
Line’ and this signal is driven by either the master or the I2C peripherals.
Both SCL and SDL lines are in open-drain state when there is no data
transfer between I2C peripherals. I2C protocol can be used to connect a
maximum of 128 devices and can operate with three modes such as fast
mode, high speed mode, and standard mode. Standard mode data speed
ranges up to 400 Kbps, the fast mode can transfer data up to 1 Mbps, and
the high speed mode can go up to 3.4 Mbps.
• SPI: Serial Peripheral Interface (SPI) protocol is developed by Motorola

and it provides a standard for transferring command and status data
between a master interface (SPI module) and slave devices on a network.
The SPI module is the network master that coordinates the flow of data
between the PLC host processor and slave devices on the network. The
SPI module can store configuration information corresponding to each
device, return configuration status to the host PLC processor, receive
command data destined for devices on the network, send data serially
to and receive status serially from the target device, repeat data trans-
fer for each device in polled order, and return status data from network
devices to the host PLC processor. Each device manufactured for use on
the SPI network must have an SPI-specified device-type identification
number (device ID). SPI protocol can support full-duplex communica-
tion feature. Configuration information that is transferred initially to the
SPI module identifies the devices with which it will communicate on the
network, establishes the order in which it will poll the devices, and sets
the network’s communication rate. Communication with devices on the
SPI network can be initiated by transferring data blocks between a PLC
processor and an SPI module.
2.5.5 PLC Networking and Interfacing

In an industrial automation network with five-layered architecture, individual PLC-
based controllers are considered to be placed in the second layer, i.e., the layer above
the field instruments layer. Networking of PLCs is a must such that integration of
two or more control operations can be done in a seamless manner. PLC networks
provide a variety of networking options to meet specific control and communications
requirements. Typical options include remote I/O, peer-to-peer, and host computer
communications, as well as LANs. These networks can provide reliable and cost
effective communications between as few as two and as many as several hundred
PLCs, computers, and other intelligent devices. PLCs can talk to each other using
standard protocols like RS-232, RS-485, MODBUS, etc. Figure 2.54 shows the net-
working of PLCs.
2.5.5.1 Remote I/O Systems

A remote I/O configuration is shown in the same figure (Figure 2.54) with
inputs and outputs at some distance away from the controller and CPU. This
type of networking can be described as a ‘master-and-slave’ configuration, and
it allows many distant digital and analog points to be controlled by a single
PLC. Typically, remote I/Os are connected to the CPU via twisted pair or fiber-
optic cables.
Remote I/O configurations can be extremely cost-effective control solutions
where only a few I/O points are needed in widely separated areas. However, it is not
always necessary to have a controller at each site. Remote I/O systems can be used
FIGURE 2.54 Networking of PLCs.
for acquiring data from remote plant locations. Information such as cycle times,
counts, duration, or events, etc. can then be sent back to the PLC for maintenance
and management reporting.
In a remote I/O configuration, the master controller polls the slave I/O for its cur-
rent I/O status. The remote I/O system responds, and the master PLC then signals the
remote I/O to change the state of outputs as dictated by the control program in the
master PLC. This entire cycle occurs hundreds of times per second.
2.5.5.2 Peer-to-Peer Networks

Peer-to-peer networks are undertaken to enhance reliability by decentralizing control
functions without sacrificing coordinated control. In this type of network, numerous
PLCs are connected to one another in a daisy-chain fashion, and a common memory
table is duplicated in the memory of each. In this way, when any PLC writes data in
this memory area, information is automatically transferred to all other PLCs present
in the network. Subsequently, they can use this information in their own operating
programs.
With peer-to-peer networks, each PLC in the network is responsible for its own
control site and only needs to be programmed under its jurisdiction. It significantly
reduces programming and debugging complexity; because all communications occur
transparently to the user, communication programming is reduced to simple read-
and-write statements. In a peer-to-peer system, there is no master PLC. However, it is
possible to designate one of the PLCs as a master for use as a type of group control-
ler. This PLC then can be used to accept input information from an operator input
terminal; e.g., sending all the necessary parameters to other PLCs and coordinating
the sequencing of various events.
2.5.5.3 Host Computer Links

PLCs can also be connected with computers or other intelligent devices. In fact, most
PLCs, from small to very large, can directly be connected to a computer or part of a
multi-drop host computer network via RS-232C or RS-422 ports. This combination
of computer and controller maximizes the capabilities of the PLC for control and
data acquisition, as well as the computer for data processing, documentation, and
operator interface.
In a PLC–computer network, all communications are initiated by the host
computer, which is connected to all the PLCs in a daisy-chain fashion. This com-
puter individually addresses each of its networked PLCs and asks for specific
information. The addressed PLC then sends its information to the computer for
storage and further analysis. This cycle occurs hundreds of times per second.
Host computers can also aid in programming PLCs: powerful programming and
documentation software is available for program development. Programs then can
be written on the computer in relay ladder logic and downloaded into the PLC. In
this way, one can create, modify, debug, and monitor PLC programs via a com-
puter terminal.
In addition to host computers, PLCs often must interface with other devices, such
as operator interface terminals for large security and building management systems.
Although many intelligent devices can communicate directly with PLCs via conven-
tional RS-232C ports and serial ASCII code, some do not have the software ability to
interface with individual PLC models. Instead, they typically send and receive data
in fixed formats. It is the PLC programmer’s responsibility to provide the necessary
software interface.
The easiest way to provide such an interface to fixed format intelligent devices is
to use an additional module on the PLC. This module is essentially a small computer
that plugs into the bus of the PLC. Equipped with RS-232C ports, this module can
easily handle ASCII communications with peripheral devices, data acquisition func-
tions, programming sequences, number crunching, report and display generation,
and other requirements.
2.5.5.4 Access, Protocol, and Modulation Functions of LANs

By using standard interfaces and protocols, LANs allow a mix of devices (PLCs,
PCs, host computers, operator interface terminals, etc.) from many different
vendors to communicate with others on the network. In case of LAN, when
multiple devices present on the network want to access the physical media at
the same time, collision occurs. To avoid collision two methodologies are fol-
lowed – CSMA/CD and Carrier Sense Multiple Access with Collision Avoidance
(CSMA/CA).
In case of sending data with a predefined time limit, token passing technique
is more convenient, where each node can transmit only if it is in possession
of a special electronic message called a token. The token is passed from node
to node, allowing each an opportunity to transmit without interference. Tokens
usually have a time limit to prevent a single node from tying up the token for a
long period. Other media access control mechanisms are also utilized by various
protocols designed as per OSI-ISO model. For encoding data before transmis-
sion, baseband modulation techniques are usually popular compared to broad-
band modulation techniques.
2.5.5.5 Network Transmission Interfaces

The vast majority of PLC communications is carried out via RS-232C and twisted
pair cables. Most PLCs have an RS-232 port and are capable of handling communica-
tions with host computers, printers, terminals, and other devices. Maximum permis-
sible transmission speed is 19.2 kbps. The distance and data transmission rates are
standards for various interfaces. Their actual performance is a function of the device
drivers and varies significantly between manufacturers. The only real limitation
on RS-232C is the 50-ft recommended distance between devices. While RS-232C
installations often can achieve cabling distances greater than this, the ‘unbalanced’
design of the interface results in a greater susceptibility to surrounding electrical
noise and reduced data integrity. This is particularly true where Electromagnetic
Interference (EMI) and radio-frequency interference exist.
Hence, for longer transmission distances, RS-422 is a better option. Unlike the
RS-232C interface, RS-422 is ‘balanced’. Each of its primary signals consists of
two wires that are always at opposite logic levels with respect to signal ground.
As a result, the interface can achieve longer transmission distance (4,000 ft) and
higher data transmission rates up to 90 kbps. In shorter runs (less than 50 ft), data
transfer can reach 10 Mbps. Fiber-optic communication is gaining greater accep-
tance and is being used in more and more installations. Fiber-optic cable is more
suitable in harsh environmental conditions and for electrical noise. Also, these
links can span extremely longer distances and transmit data at very high speeds.
For such cases, lesser number of repeaters is needed for data to travel from trans-
mitter to receiver.
2.6 SELECTION AND COMMISSIONING OF PLC

2.6.1 PLC Selection Criteria
Selection of a PLC for an industrial automation-based application depends on several
factors. In this context, the role of the project/design engineer is very crucial as he
has to take into considerations a number of factors related to the past, present, and
future of the various PLC models available from different vendors. Usually the selec-
tion criterion is dependent on the following parameters:
• System requirements: Particular needs of the project should be evaluated.

Once this is done, the entire task can be broken into a number of simple
explicable elements, each of which can be easily described.
• Application requirements: One needs to identify the area of application,
i.e., what input and output devices need to be connected. They may be
simple on/off type, pulsating, or continuous in nature. In addition, one
must also find out the required special functions other than conventional
binary logic.
• Electrical requirements: Current and voltage ratings of the I/O devices
need to be defined and connected along with the system power require-
ments. The number of I/O modules required and their nature, i.e., current
sourcing/sinking type must be known.
• Speed of operation: The speed of operation, i.e., scan time plays a piv-
otal part in choosing the right type of PLC for a particular application. It
depends on the dynamic behavior of the process or application and in such
cases one needs to consider the time requirement for the fastest possible
operation (i.e., input device sensing to output device actuation). CPU speed
as well as the size of the memory are the other important parameters in
deciding the PLC speed of operation.
• Communication: Communication is an important requirement especially
in case of networking PLCs. If a PLC needs to communicate with another
PLC, I/O modules, operator interface, or any other devices, then the choice
of the communication requirement needs to be specified. In case of time-
critical applications of PLC, the choice of appropriate communication pro-
tocol is an important factor.
• Operator interface and software: Normally, for large-sized applica-
tions involving considerable number of I/O devices, operator interface
is provided to enable the operator to keep a constant update on the
PLC operation. Traditional operator interface includes push buttons,
pilot lamps, LEDs, and numeric display, but modern interfaces are
graphical display devices (usually PC monitor), which can display
graphical as well as text messages about the process status. Choice of
programming language is an important factor in deciding the choice
of the PLC.
• Physical environment: Industrial PLCs are usually located in the field
and hence their ability to withstand harsh environment is crucial in
deciding the choice of PLC. Protection against liquid and solid materials
is known by the term ‘ingress protection’, i.e., IP. Thus, a design engi-
neer must decide the required IP value of the enclosure for the PLC to be
chosen. Physical housing of the PLC along with its enclosure is decided
keeping in mind the maintenance, troubleshooting, and program modi-
fication issues.
2.6.2 Vendor Selection
A large number of PLC vendors are available in the market with various prod-
ucts having different features. Thus, choice of appropriate vendor is not an easy
task as it has to meet the industrial automation requirements. It should support
future expandability requirements and must provide a cost-effective solution for
the entire operational period. The final choice of vendor or supplier also depends
on its product functionality, existing customer feedback, availability of quick
support, comprehensive training for the technicians and engineers, systematic
and exhaustive operating manuals, future model upgradation and expansion

facility, etc. Some of the well-known PLC vendors and their products are listed
below:
• Rockwell Automation (Allen-Bradley) is one of the major PLC vendors

and their products are designed for large, small, and micro control applica-
tions. ControlLogix model is suitable for large applications, CompactLogix
is suitable for midsized applications, and MicroLogix is preferred for small
and standalone applications.
• Siemens PLC is widely used in metallurgy, chemical industry, printing
production lines, etc. A large variety of PLC models are available from
Siemens. Out of which S7-200 is suited for mini applications, S7-300 and
400 are for micro applications, and S7-1200, which has modular structure,
is preferred in large-sized applications.
• Another well-known and high-end PLC manufacturer is ABB. They
offer their AC500 lineup that caters the need from small to large high-
end applications. One special feature of ABB PLC is that its CPU model
can be used with any model of AC500 series. AC500-eCo is a com-
pact model PLC suitable for flexible and economical configurations for
automation solutions in smaller applications. AC500-S is a safety PLC
designed for safety applications involved in factory, machinery, or pro-
cess automation area. AC500-XC is a model suited for extreme ambi-
ent conditions like high temperature, vibration, presence of hazardous
gases, high humidity, etc.
• Schneider Electric’s Modicon PLC is available in different models.
Modicon M340 is suitable for midsized process automation; Modicon M580
is Ethernet programmable automation and safety PLC for processes with
high availability as well as safety standalone solutions. Modicon Quantum
is a modular PLC for large process applications.
Other well-known PLC manufacturers are Honeywell, Mitsubishi, Omron,

Yokogawa, Danaher, Fuji, Toshiba, GE, etc. There are nearly more than
100 companies throughout the world offering different PLCs having different
features. Obvious advantages of selecting PLCs from major vendors are that
they have products required for better integration in designing the entire automa-
tion loop.
2.6.3 PLC Commissioning

In general, the term commissioning in the field of industrial automation is the pro-
cess of assuring that all systems and components of an industrial plant are designed,
installed, tested, operated, and maintained according to the operational require-
ments. Now, if the plant is to be controlled by a PLC, then the initial phase of pro-
gramming is usually done at the office of the vendor rather than at the plant. After a
generic verification and approval by the client, the PLC is installed in the panel for
dispatching to the plant.
Subsequently, as the panel reaches the plant or site, necessary installation,

wiring, grounding, and power supply connection are made by the plant tech-
nicians. All the field wirings for connecting I/O devices with I/O modules of
the PLC should be done properly with appropriate tagging. Here, the role of
engineer or commissioning engineer is very crucial as he has to ensure that all
the wirings are done properly as per the design specifications. Thereafter, PLC
programs need to be edited according to the plant condition. Reasons for such
change are plenty, for example, certain motor shall be eliminated and the group
sequence must run without it; a new system of interlocks is required based on the
site conditions, appropriate scaling of analog values, and proper tuning of PID
parameters, etc.
The above steps are performed at the site by the commissioning engineers. All
the programs are tested and their outputs are verified as per the design specifica-
tions. After successful trial runs for all the designed logic, clearance is provided
by the PLC team to kick start the plant. To ensure safety of the PLC and the
connected devices, every safety device needs to be checked. Functionality of
the emergency stop button is tested. Uninterruptable supply of power must be
ensured. Preventive maintenance steps are tested. At present, most PLCs contain
some software for offline checking of the installed programs. It provides a list
on a screen or as printout if any error is detected. Thus, the plant PLC is said to
be commissioned.
2.6.4 PLC Auxiliary Functions

Most of the PLC manufacturers offer a set of auxiliary functions. Out of these, the
most popular functions are Monitor, Force, and Print, which serve special purposes
like testing, debugging, documentation, etc.
• Monitor function: Monitor functions help in analyzing a part of the

PLC program. Its role is similar to the Edit mode where a section of
the entire program is highlighted to evaluate its performance. By using
Monitor function, the register status, relay coil, and contact status can
be read. Register content can be displayed in binary as well as in other
formats. So, using Monitor function, performance of a portion of the
PLC program can be evaluated and it is usually done in offline mode,
i.e., during simulation study. Figure 2.55 shows the monitor mode
for LD.
• Force function: It is a special type of function which enables overriding
the predefined program flow and can turn ON or OFF any contact or coil.
Thus, any NO contact can be made NC by using Force function and vice
versa. Similarly, relay coils can be energized or de-energized by such a
function. Normally, Force function is used for checking the functional-
ity of individual instruction (single rung in case of LD) of PLC program.
However, Force function is not applicable for all types of PLC functions.
It is always suggested that the Force function should be used only during
FIGURE 2.55 Monitor mode for Ladder Diagram.
offline mode, otherwise it may cause accident. The Force mode for LD is
shown in Figure 2.56.
• Print function: PLC print function is used for having hard copy printout
for a section or the entire program for debugging or for keeping record.
Printout for a section of the program or a continuous print can be taken
for the entire program. In case of ladder program, as each rung has a refer-
ence number, printout can be taken with cross reference number for easy
understanding.
2.6.5 Maintenance of PLC
Though PLCs are manufactured with the knowledge that they are going to be used
in harsh industrial environment, regular maintenance of PLCs is important for
smooth running of a plant; otherwise, downtime of the plant will cause a huge pro-
duction loss. Thus, preventive maintenance is a regular job for plant technicians
and engineers. A routine maintenance schedule increases the longevity of PLCs and
FIGURE 2.56 Force mode for Ladder Diagram.

minimizes the chance of system malfunctioning. Usually following steps are to be

taken for PLC maintenance:
• Backup PLC program: An up-to-date copy of the PLC program must be

maintained. In case the PLC becomes inoperative, and needs replacement,
the backup file can be downloaded immediately onto the replaced PLC.
• Checking of power sources: Operating voltage needs to be checked to ensure
whether they are in the operating range and free from spikes. If the LED indica-
tor blinks, battery needs to be replaced immediately to avoid any loss of data.
• Checking of operating environment: Operating temperature, humidity,
and other environmental factors need to be checked regularly so that the
satisfactory operating condition for PLC is ensured.
• Dust cleaning and ventilation checking: Regular cleaning is required to
remove the deposited dust on PLC components. The cooling vents must remain
clear and air filters should be clean for proper ventilation. Unobstructed air
supply ensures heat dissipation of the electrical components.
• Checking for connections and discoloration: All the connections related
to power and communication cables, wiring for I/O modules are required
to be checked. They must be tightened to avoid any loose contact. Due to
overheating, discoloration occurs and it may result in burnt odor. So, each
and every component needs to be checked for any such symptoms.
• Program checking and necessary updates: Proper functioning of the
programs need to be checked and if any modification is incorporated, then
it is very essential to ensure the desired functioning of the intended task.
• Removal of unnecessary items: All unnecessary items related to draw-
ings, manuals, wirings need to be removed from the PLC cabinet.
• Check inventory of replacement items: The inventory of the replaced
items and availability of spares in stock should be ensured so that downtime
due to component failure can be minimized.
• Calibration of analog modules: For proper function of analog modules,
they need to be calibrated at least in the interval of every six months.
Apart from the above, any equipment or machinery causing heat dissipation, vibra-
tion, emission of volatile components, and EMI should not be placed in the vicinity
of the PLC cabinet. In addition, tagging of the wires and components should not be
disturbed.
2.6.6 Operational Safety of PLC

Safety precautions are required to be observed for using the PLC safely and
correctly in order to prevent possible accidents and hazards during daily opera-
tions. The safety precautions can be divided into two parts: warning and cau-
tion. Warning indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury. Caution implies that incorrect handling may
cause hazardous conditions, resulting in moderate or minor personal injury, or
physical damage.
Normally, two standard symbols are used for signifying different types of hazards
as follows:
meant for paying attention due to danger in specific situations
meant for paying attention because of danger due to electrical shock
Following precautions should be followed for operational safety of a PLC:
• External safety features such as emergency stop, mechanical damage, pre-

venting interlock positioning upper and lower limit switches, and interlock-
ing forward/reverse operation need to be installed outside the PLC.
• To protect devices against over current, i.e., exceeding the rated current
value, fuses of proper rating should be used.
• External power supply to the I/O devices should be turned on after the PLC
module power is turned on.
• Communication cables should not be bunched together with the power
cables of PLC, sufficient separation distance (minimum 100 mm) should be
provided between them.
• Before initiating any maintenance work, power supply to the PLC modules
should be turned off.
• After making any replacement or change in wiring, each and every connec-
tion should be properly tightened to avoid any loose contact.
• Proper grounding should be ensured.
2.7 FUTURE OF PLC

2.7.1 PLC-Based Automation
The majority of industrial automation systems are designed based on PLCs to main-
tain the desired process operating conditions. From simple discrete level automation
systems to complicated continuous automation processes are designed using PLCs
along with sensors and actuators. Output of sensors, after proper signal condition-
ing, are connected to the input modules of the PLCs. On the other hand, outputs of
PLCs are fed to the actuators through output modules. The entire logical relations
are developed in the PLCs with the help of various programming tools such as LDs,
SFCs, FBDs, etc.
Example 2.1: Two-tank level control using PLC
A two-tank level control using PLC is shown in Figure 2.57.

Here, the task is to control the level of both the tanks – Tank 1 and Tank 2 by
controlling the solenoid activated valves. For sensing the liquid levels in Tank 1,
two level switches (LHS1 and LLS1) are connected. In Tank 2, one level switch
(LLS2) is connected for sensing lower liquid level.
I/O for the two-tank level control system:
Input Output
LHS1, I: 1/0 = Level High Switch of Tank 1 O: 2/0 = Inlet solenoid valve to Tank 1
LLS1, I: 1/1 = Level Low Switch of Tank 1 O: 2/1 = Connecting solenoid valve
LLS2, I: 1/2 = Level Low Switch of Tank 2 between Tank 1 and Tank 2
I: 1/3 = Set point for Tank 1 O: 2/2 = Outlet solenoid valve of Tank 2
I: 1/4 = Set point for Tank 2
I: 1/20 = Start
I: 1/21 = Stop
Bit: 10:1/0 = Emergency stop
FIGURE 2.57 Two-tank liquid level control with PLC.

FIGURE 2.58 Ladder Diagram for two-tank liquid level control with PLC.
LD of the two-tank level control system is shown in Figure 2.58.
PROGRAM DESCRIPTION
• Rung 0001 – Master start/stop rung to Start/Stop the entire process.
• Rung 0002 – Controls connecting valve output O: 2/1. It is opened when
LHS1 I: 1/0, set point for Tank 1 I: 1/3 and LLS2 I: 1/2 are energized. O:
2/1 is closed when LLS1 I: 1/1 is energized, or in other words when Tank
1 is empty.
• Rung 0003 – Controls inlet valve O: 2/0. It allows the inlet flow by open-
ing inlet valve whenever LLS1 I: 1/1 is energized.
• Rung 0004 – Controls outlet valve with address O: 2/2. It allows the liq-
uid to flow out when set point for Tank 2 I: 1/4 is energized.
Example 2.2: Two liquid mixing using PLC
The two liquid mixing using PLC is shown in Figure 2.59.

FIGURE 2.59 Liquid mixing process with PLC.
I/O of the liquid mixing system:
Input Output
LHS1, I: 1/0 = Level High Switch of Tank O: 2/0 = Inlet valve for liquid 1 to Tank
LLS1, I: 1/1 = Level Low Switch of Tank O: 2/1 = Inlet valve for liquid 2 to Tank
I: 1/20 = Start O: 2/2 = Outlet valve of Tank
I: 1/21 = Stop O: 2/3 = Stirrer motor of Tank
Bit: 10:1/0 = Emergency stop
The LD of the liquid mixing system is shown in Figure 2.60.
PROGRAM DESCRIPTION
• Rung 0001 – Master start/stop rung to Start/Stop the entire process. By
pressing Start I: 1/20, inlet liquid valve O: 2/0 opens and liquid 1 starts
flowing into the tank until the level reaches to LLS1, I: 1/1, i.e., low-level
float sensor.
• Rung 0002 – Once LLS1, I: 1/1, i.e., low-level float sensor is energized,
inlet liquid valve O: 2/1 opens and liquid 2 starts flowing into the tank
until the level reaches to LHS1, I: 1/0, i.e., high-level float sensor.
• Rung 0003 – As LHS1, I: 1/0, i.e., high-level float sensor is energized,
Stirrer starts operation, and the Timer T0 starts counting for 60 sec. After
60 sec, T0 will be ON and stirrer stops working.
• Rung 0004 – Once T0 becomes ON, valve O: 2/2 will open and the
liquid mixture drains out from Tank.
• Rung 0005 – As outlet valve O: 2/2 opens, Timer T1 starts counting for
120 sec. After 120 sec, T1 will be ON and outlet valve O: 2/2 closes to
stop draining of mixture liquid.
Stop I: 1/21 switch is used to stop the process and in an emergency situation, to
stop the process, Emergency stop switch bit: 10: 1/0 can be pressed.
FIGURE 2.60 Ladder Diagram for liquid mixing control with PLC.
2.7.2 PLC and Programmable Automation Controller

Both the PLCs and PACs are basically industrial computers designed and adapted
for manufacturing environments. These computers are the brains of any manu-
facturing operation, providing highly reliable control of industrial automation
processes. In practice, PLCs and PACs are very similar to each other as they both
perform almost similar functions and with time their differences are becoming
more and more blurred. PLCs are being widely used in process automation for
more than 40 years and hence are quite well-accepted. However, PACs are rela-
tively new and they are being selectively used in the automation process hardly
in the last 20 years. Till now no standard definition or classification is available
for PACs.
In practice, PLCs are better suited for incorporating automation in industrial
applications. PLCs have simple program execution scans but limited memory and
discrete I/O. Modern PLCs are capable of high-speed I/O devices, sequencing, and
PID control, in addition to digital and analog I/Os. Many PLCs have built-in net-
works enabling communication between multiple PLCs, distributed I/Os, and com-
munication between HMIs, and supervisory control and data acquisition systems.
However, PLCs are particularly suitable for simpler processes and smaller automa-
tion projects that do not require rapid scalability.
PACs have an open architecture and modular design which can be connected
to an array of devices. PACs can be connected to form networks where they can
communicate with each other. Due to seamless connectivity, centralized monitor-
ing and control across multiple networks and devices can be achieved. This is
possible because PACs utilize standard protocols and network technologies such
as Ethernet, OPC (Object Linking and Embedding, i.e., OLE for process con-
trol), and Structured Query Language (SQL). Due to their modular design, system
expansion with PACs is quite simple. Adding or removing components is easier
to implement. PACs are capable of monitoring and controlling thousands of I/O
points, in addition to offering tag-based programming. With tag-based program-
ming, a single tag name database is used for development, and these tags can be
assigned a variety of functions before being tied to a specific I/O. PACs provide
more flexibility in programming, larger memory capacity, and better scalability
to aid in future expansion. They are particularly useful for systems with a high
percentage of analog I/O. Often, they are implemented in systems with extensive
network interface requirements and systems with direct user interaction require-
ments. PACs are more suitable for large scale automation projects with complexi-
ties and they are appropriate for large scale automation systems composed of
several PC-based software applications.
So, in a broad sense, the following characteristics differentiate PACs from PLCs:
• Multi-domain functionality (can operate simultaneously with motion con-

trol, sequential control, logic, data management, and communication –
using a single platform)
• A single, multidiscipline development platform (programming is done in an
integrated development environment that uses a single, tag name database
which is used by all software applications – such as HMIs, Enterprise

Resource Planning (ERP) systems, and vision applications)
• Flexible software tools that maximize process flow across machines or pro-
cesses (PACs use the IEC 61131-3 programming languages – LD, FBD,
SFC, ST, and some include standard PC programming languages such as
C/C++)
• An open, modular architecture (highly modular architecture and
hence quite simple for mounting and replacing with strong future
expandability)
• Compatibility with enterprise networks (open architecture and modu-
lar design to facilitate communication and interoperability with other
devices, networks, and enterprise systems using almost all standard
protocols).
2.7.3 Unified Human-Machine Interface

HMI is a user interface or dashboard that connects a person to a machine, system,
or device. Technically the term HMI is applicable to any screen that allows a user
to interact with a device. But in practice, the term HMI is most commonly used
in the context of centralized monitoring of an industrial process. HMI allows an
operator to monitor, control, and collect data and can also be used to program the
system. Now, the concept of unified HMI is an extension over its functionality,
where the same interface (usually PC screen) can be used for commissioning,
operation, maintenance, sequential control, continuous control, programming,
networking, supply chain, business forecasting, etc. Moreover, the same HMI can
be used as an interface for more than one Distributed Control System from sepa-
rate vendors.
HMI is nothing but a GUI which facilitates information exchange and commu-
nication between the user and the concerned system. Hence, the software employed
for designing the GUI plays an important role in deciding its functionality. There are
two basic types of HMI software: supervisory level and machine level. The super-
visory level is designed for control room environment and used for system control
and data acquisition. It mainly involves a process control application which collects
data from sensors and sends the information to a central computer for processing.
Alternatively, machine-level HMI involves the presentation of operating status for
its various units related to a particular production facility. Usually, most of the HMI
software is designed for either supervisory level or machine level; however, in case of
unified HMI, applications that are suitable for both types of HMI are also available.
These software applications are more expensive but can eliminate redundancies and
reduce long-term costs.
The choice of HMI software requires an analysis of product specifications and
features. Important considerations include system architectures, standards and plat-
forms; ease of implementation, administration, and use; performance, scalability,
and integration; and total costs and pricing. Some HMI software provide data log-
ging, alarms, security, forecasting, operations planning, and control. Others support
data migration from legacy systems. Unified HMI supports a number of network
communications which include ControlNet and DeviceNet. ControlNet is a real-
time, control layer network that provides high-speed transportation of both time-
critical I/O data and messaging data. DeviceNet is designed to connect industrial
devices such as limit switches, photoelectric cells, valve manifolds, motor starters,
drives, and operator displays to PLCs and PCs. A number of HMI software run on
Microsoft Windows CE, a version of the Windows operating system that is designed
for handheld devices. Windows CE allows users to deploy the same HMI software
on distributed HMI servers, machine-level embedded HMI, diskless open HMI
machines, and portable or pocket-sized HMI devices.
At present, most of the HMI screens are touch-sensitive for easy functionality.
They are available in various sizes depending on actual application. Operators and
users are increasingly moving toward high-performance HMI which ensures fast and
effective interaction. It helps the viewer to observe and respond to problems more
efficiently, as well as make better-informed decisions. High-performance HMI is
simple, clean, and purposely cleared of any extraneous graphics or controls. Its color,
size, and placement are used with discretion to optimize user experience. In today’s
scenario of mobile communication, remote monitoring of plant or process informa-
tion has become a standard practice. Mobile-based remote monitoring allows greater
flexibility and accessibility for process engineers. With this feature, an offsite control
system engineer can confirm the temperature of a warehouse on a portable device,
eliminating the need for onsite supervision after working hours. Checking a process
on the factory floor while being miles away from the facility has become a standard
practice. Additionally, it is becoming more common to send data from local HMIs
to the cloud, where it can be accessed and analyzed remotely, while keeping control
capabilities local. Future HMI technology is moving toward Augmented Reality and
Virtual Reality to visualize the manufacturing functions for its clear understanding
and hence quick and correct decision-making can be accomplished by a process
engineer.
2.7.4 Plug and Play Solution

Plug and play, often abbreviated as PnP, is a modern terminology related to elec-
tronic hardware items which are connected with PC. For conventional hardware,
once it is connected to the computer, we need to install the related driver for its
functioning. But, in the case of PnP, it has the ability to find and configure the
hardware components without having to set DIP switches and jumpers. PnP com-
patible devices have BIOS which can be accessed by the operating system of the
PC for necessary interfacing. PnP BIOS identifies the attached peripheral devices
and regulates the proper internal settings by configuring the direct memory access,
interrupt requests, and I/O addresses and as a result the PnP device starts function-
ing in a seamless manner.
Thus, the PnP feature is gaining more and more popularity for easy installation
in lesser time. Modern PACs, which are basically industrial computers with PLC
functionality, are packed with the PnP feature. Due to its modular structure, the
PnP solution helps in easy and hassle-free installation of each module. There is no
need for switching the power off or restarting the system, i.e., it has hot-swapping
or hot-plugging feature. In case of multi-vendor configuration of PAC, PnP is a very
important feature for connecting individual modules, but this technology is still in
its development stage.
2.7.5 Wireless Link of PLC

At present, with the development of wireless communication technologies, PLC
vendors are also providing wireless link between PLC processor, i.e., CPU mod-
ule and various I/O modules. Usually, in case of small applications with limited
number of I/O devices, such types of wireless links are employed. In some instal-
lations, due to the awkward location of sensors and actuators, routing of cables
is a challenging and stupendous task. In such cases, wireless linked I/O modules
are gradually getting acceptance. For short distance communications, RF links
are utilized, otherwise GPRS/GSM link is used. Figure 2.61 shows wireless I/O
modules for a PLC.
In some cases, wireless connectivity is also used to connect operator station, i.e.,
HMI with the PLC. Moreover, in case of networking of PLCs, for PLC to PLC com-
munication wireless link is also employed.
FIGURE 2.61 Wireless I/O modules of PLC.

2.7.6 Enterprise Resource Planning with PLC

ERP is basically a software platform for smooth running of the entire process auto-
mation, i.e., from raw material procurement to final product shipment. The main goal
of ERP is to cut cost and to enhance the performance of any automation process to
maximize profit. ERP helps in the following ways:
• Reduced operational cost

• Increased company profit
• Appropriate use of process automation
• More accurate data with real-time information
• Better management of company assets, inventories, capacity, schedules,
forecasts, orders, etc.
Now, at the field level of an automation network, most of the industrial automation
processes are run by PLC. So, to increase productivity with lesser operation cost,
PLCs are integrated with the ERP platform. In the early days, there was no such con-
nectivity but at present with Industry 4.0, PLCs have become an integral component
of ERP software.
PLCs are quite efficient to handle batch processes but their major drawback
is that they can’t store data. They are fed by sensors/switches regarding the real-
time plant status and provide necessary corrective measures, but they do not keep
a record of the data. Moreover, PLCs can’t convert the data into comprehensive
reports relating to production or extract useful information from the data for the
management, which helps in future decision-making. Hence, by integrating ERP
with PLC, many departments like management, production, maintenance, sales,
and marketing, etc. are getting benefited. The plant maintenance module of the
ERP system stores information about the functioning of various equipment along
with the PLC. For any necessary upgradation and fixing of various operational
issues, it would offer the ability to create proactive and preventive maintenance
plans. The maintenance schedule for each machine, as defined in the ERP system,
would be synchronized with the PLC system’s knowledge of the actual machine
condition. Thus, it helps in keeping the technical personnel one step ahead of any
possibility of a costly equipment failure.
Providing real-time/current information, in addition to historical information, the
integration of an ERP with a PLC system would increase the transparency and vis-
ibility in information availability, allowing the management to take timely decisions.
The end users would also gain a significant advantage from the automated data gen-
eration, as it would lessen the amount of time-consuming manual work and reduce
the possibility of mistakes. Hence, by integrating ERP with PLC, an automation
process is benefited in the following ways:
• Meet and/or exceed quality standards

• Reduce equipment failures
• Cut maintenance costs
• Maintain regulatory compliance
• Increase operational efficiency

• Improve data transparency and visibility
• Create comprehensive reports
• Execute real-time monitoring and control
• Automate data generation and collection
• Store historical data
• Improve the decision-making process
• Reduce labor cost and human errors
Hence, in modern industrial automation processes, PLCs are becoming an integral

part of the ERP platform.
2.7.7 Industrial Internet of Things and PLC

Due to the enormous growth of internet technology, Internet of Things (IoT) is now
also being employed for industrial automation processes and this special class of IoT
is termed as Industrial Internet of Things (IIoT). Features of the conventional PLCs
are getting modified continuously due to the bridging of IIoT with PLC. The enor-
mous power of internet technology has provided various additional features in PLC
functioning as give below:
• Data collection and analysis: By use of IIoT, a large amount of data can be
collected from processes and equipment and placed in the ‘cloud server’ for
future study and trend analysis. The objective is to optimize and reorganize
the processes so that we can reduce the waste and to provide faster response
to customer demands.
• Faster business decision: Management has easy access to various types of
data related to the entire process (e.g., raw material procurement to market
demand) operation and hence business policy can be decided in a much
lesser time, which leads to competitive advantage.
• Enhanced networking: Conventional centralized PLCs will be replaced
by multiple smaller networked PLCs (micro and nano PLCs) that are placed
closer to the sensors they are monitoring and the mechanisms they are con-
trolling. Micro or nano PLCs designed to communicate as part of the IIoT
are emerging to fulfill this type of role, providing I/O channels a small
footprint with modular expansion options.
• Remote sensor data and PLC diagnostic data historian: By incorporat-
ing additional sensors to the PLCs, we can have the diagnostic data for the
PLC in any web or mobile browser from anywhere. This will help in early
maintenance to avoid any possible major failure of any equipment.
• Alerts: Email alerts can be set up for plant maintenance engineers when
diagnostics and sensor readings reach certain threshold values or any type
of abnormal behavior of the plant.
• Data visualization: Plant engineers have data visualization option from
any remote location containing graphs and charts for easy interpretation
and understanding.
• Remote debugging and upgradation: Engineers can debug PLC programs

from any location and also can install the new drivers without affecting the
plant normal activity.
• Sensor correlation: Data present in the cloud from various sensors can
be correlated through data analytics and it helps to predict any possible
future abnormality so that preventive measures can be taken to minimize
downtime.
• System optimization: Various optimization tools can be employed by the
plant engineers in relation to a specific property of a system like energy
usage, and they use sensor data to determine how it should be configured at
any given time so that its energy consumption becomes as low as possible.
With time, new features are being added to PLCs based on IIoT and it helps in attain-
ing new dimensions in PLC-based process automation technology.

Chapter 2

Uploaded by

Copyright:

Available Formats

Chapter 2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 2

Uploaded by

Copyright:

Available Formats

2 Programmable Logic

2.1 BASICS OF PLC

2.1.2 Sustainability of PLC

FIGURE 2.1 A panel consisting of hardwired logic.

logic programming. In industrial environment, technicians are more conversant

2.1.3 Definition of PLC

FIGURE 2.2 Progress of PLC with time.

FIGURE 2.3 Schematic diagram of a PLC.

2.1.4 Classifications of PLCs

• Structural classification: As far as the structure of a PLC is concerned, it

• I/O point-based classification: Depending on the number of available I/O

2.1.5 Role of PLC in Process Automation

1. Flexibility: If there is any change in process operations or any change in

2. Easy troubleshooting: PLC program can be easily tested and evaluated

It has strong electrical noise immunity. Manufacturers’ report depicts

Another advantageous feature of PLCs is that it allows piecemeal implementation of

2.1.7 I/O Devices of PLC

Type Purpose Figure

Limit switch Positional status

Proximity detector Positional status of the objects

Push button Command input

Thumbwheel switch To provide set value

Photoelectric switch Positional status of the objects

Thermostat Temperature status

Type Purpose Figure

Solenoid valve Flow control

Starter Starting of a motor

Display lamp Status information display

2.1.8 PLC Programming Devices

FIGURE 2.4 Various PLC programming devices.

1. Direct program entry to the program memory (random access memory

2.1.9 PLC Selection Criteria

• System requirements: It basically defines the task to be executed by the

2.1.10 Major PLC Vendors and their Products

• Availability of a wide range of products equipped with appropriate external

• Competitive prices with advanced functionalities

• Tier 1 manufacturers in the automation industry are Siemens, Rockwell

2.1.10.1 Top Five PLC Vendors

• OMRON: OMRON range of PLCs range from small-scale equipment con-

2.2 DESIGN AND OPERATION OF PLC

• Processor: Processor, i.e., CPU, is basically a microprocessor and it inter-

FIGURE 2.5 Block diagram of a PLC.

FIGURE 2.6 Architecture of a PLC.

FIGURE 2.7 PLC power supply module.

FIGURE 2.8 Program and data sections of PLC RAM.

2.2.2 Central Control Unit of PLC

2.2.3 Functional Modes of PLC

FIGURE 2.9 CPU structure of the PLC.

• Program mode: In program mode, the operation of CPU is stopped. User

2.2.4 PLC Program Structure and Execution

FIGURE 2.10 PLC scan cycle.

2.2.5 Programming Devices for PLC

2.2.6 Selection of I/O Modules for PLC – Sourcing

2.3 PLC PROGRAMMING TOOLS

• Function Block Diagram: FBD programming technique is similar to

2.3.2 IEC 61131-3 Structuring Resources

• Ladder diagram – graphical

2.3.3 Ladder Diagram

2.2.6 Selection of I/O Modules for PLC – Sourcing