Scribd Logo
Upload

Welcome to Scribd!

  • 30 views

    Sirena PA200

    Uploaded by

    Eduardo Huenufil
    This document provides installation instructions for an outdoor siren with the following key steps: 1. Mark and drill holes to mount the siren housing on a wall. 2. Open the siren housing and connect wires to terminals, then plug the terminals into a PCB board. 3. Connect a backup battery, ensuring correct polarity to avoid damaging the driver circuit. 4. Close and secure the siren housing.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Sirena PA200

    Uploaded by

    Eduardo Huenufil
    30 views4 pages
    This document provides installation instructions for an outdoor siren with the following key steps: 1. Mark and drill holes to mount the siren housing on a wall. 2. Open the siren housing and connect wires to terminals, then plug the terminals into a PCB board. 3. Connect a backup battery, ensuring correct polarity to avoid damaging the driver circuit. 4. Close and secure the siren housing.

    Original Title

    Sirena PA200 (2)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides installation instructions for an outdoor siren with the following key steps: 1. Mark and drill holes to mount the siren housing on a wall. 2. Open the siren housing and connect wires to terminals, then plug the terminals into a PCB board. 3. Connect a backup battery, ensuring correct polarity to avoid damaging the driver circuit. 4. Close and secure the siren housing.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    30 views4 pages

    Sirena PA200

    Uploaded by

    Eduardo Huenufil
    This document provides installation instructions for an outdoor siren with the following key steps: 1. Mark and drill holes to mount the siren housing on a wall. 2. Open the siren housing and connect wires to terminals, then plug the terminals into a PCB board. 3. Connect a backup battery, ensuring correct polarity to avoid damaging the driver circuit. 4. Close and secure the siren housing.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    lnstallation ínstructions

    1. Choose the mounting location for the siren{he wall must be even and free of hole and
    excessive protrusions.
    2. Mark and drill 5 holes with help of attach drill pattern plate (4 holes for the housing base and
    for the hanging hole).

    3. Open the siren housing (1 screw on the front),and remove the metal cover (2 screws)

    Cut o.ff the power befóre wu make the connection!

    4. UnPlug the removable terminal, mount the siren housing on the wall. Connect the wires to ihe
    terminals.

    5. Plug the terminals to your PCB board.

    6. Power on the system and check its function properly

    7. Connect the back-up battery

    ' keep attent¡on to the polorit\ of the battery; a reterse poluif can cause
    of the drtuer circuit.

    8. Mount the metal cover with 2 screws

    9. Close the housing with 1 screw.

    Terminal Block Connection


    2013.1. 11

    --
    ut door- Strobe EÉ Lll
    I

    - ,orao nr, EÉ I

    -- ñO *mñ/aLffi

    ram tD-
    -
    r-
    -
    O
    -
    sPr
    -
    Irr
    Lr-----11
    I
    li.::;;;H
    Terminal 1-Marked "FL-"trigger for the flashlight only, it is connected to the negative output of the
    alarm system, Active while the input is low.

    Terminal 2- Marked "Go-" trigger for the siren and the flashlight, active while the input is negative.

    Terminal 3-Marked "GO+" trigger for the siren and flashlight, active while the input is positive.

    Terminal 4-Marked the "GND" connect to the ground of the control unit.

    Terminal S-Marked"+14V" connect to a positive voltage output of the 13.6-14.2VDC source (usually
    from the alarm control unit).
    Terminal 6&7-Marked 'TMP" if a tamper function is required. Connect these terminals to a 24-hour
    normally closed alarm zone in the control unit, if the front cover of the siren is opened or siren box is
    taken from the wall, an immediate alarm signal will be sent to the control unit.
    Siren Specifications

    '120db
    SPL

    Fundamental Frequency 1850H2

    Siren Tone Yelp

    Frequency Range 1300-2400H2

    Flashlight Lamp 12VDC/SW

    Power supply Voltage 13.8-14.ZVDC

    3harge Current Limit 250mA

    3urrent Consumption(Speaker and strobe) Standby:8mA

    \larm [email protected]

    Maximum Power 50W(peak)

    Trigger Level lrigger Low=Max.1VDC

    Trigger High=Min.9VDC

    Siren Alarm Period :ontinous

    3 minutes

    nput lmpedance(Alarm/Flash/Trigger) 1K ohm

    Iamper Switch N.C 28VDC Maximum current 0.1A-open wher


    cover is removed

    Backup Battery Rechargeable Lead Acid Battery 12VDC up tc


    4Ah

    Low Battery Level 3VDC+/-0.3VDC

    lMaterial lxternal Box: ABS (3mm Thickness)

    nternal cover: zinc plated metal

    Dimensions of Unit [=275mm.W=1 90mm.H=95mm

    Weight(without battery) 1.85K9

    Operating Temperature Range -30 to +60'C

    Sase Protection Level Water splash resistant

    )lastic ABS with UV Proiection

    lonformal coated circuit board


    REFERENCE WIRING

    TAMFER +14V GND GO+ GO. FL.

    C
    o
    o
    C
    Outdoor Back-up Batteru Siren

    Manual lnstallation

    The outdoor siren is a new generation of professional high power acoustic siren with battery back-up
    and flashlight, which includes all pedormance and reliability for security alarm system.

    Features:
    OOutdoor battery back-up siren with lamp light or strobe light.
    ODouble housing:External-3mm plastic ABS with UV perention, internal 0.8mm metal case.
    lContinuous frequency modulated sound.
    aTamper protection in 3 ways -screw or cover opening or taking off housing from the wall.
    aPositive and negative alarm trigger input.
    I Negative trigger input to active the light only.

    OSiren period can set as follow trigger or 3 min cutoff.


    iSeleci from the lamp or xenon.
    <)Alarm when main power failure"

    <) Protecting against totally battery discharge.


    l}Plug terminal for easy installation.
    I Environmental immunity.

    Functional Description Alarm Triqger


    Applying alarm panel positive or negative output to the "GO+" or "GO-" inputs terminals respectively
    to tr¡gger the alarm. The sound and flashlight triggered together.
    Alarm siren duration dependes on the jumper select. Continuous or 3 minutes cutoff. 3-minutes
    cutoof timer is recommended to avoid vilation of any local regulations.
    Flash Triqqer:

    Applying alarm negative trigger to "FL-" terminal to trigger the flashlight. Flashlight duration is not
    limited and the t¡me of flashlight is up to control panel.

    Tamper:

    N/O and N/C tamper switch is equiped. The default is N/C. While the housing is closed with the
    screw, the tamper terminals are shorted (0 ohm). User can change N/C to N/O if necessary.

    Power Failure:

    When power failure, the siren and flashlight are triggered until power supply is restored or battery
    voltate is less than 8VDC.

    Batterv Protection:
    The siren is supplied with protection against totally battery discharge by cutting off the siren, when
    voltage level falls down to less then 8VDC.

    You might also like