Different Types of Chassis

Ladder Chassis

AC Cobra's chassis.

This is the earliest kind of chassis. From the earliest cars until the early 60s, nearly all cars in the world
used it as standard. Even in today, most SUVs still employ it. Its construction, indicated by its name,
looks like a ladder - two longitudinal rails interconnected by several lateral and cross braces. The longitude
members are the main stress member. They deal with the load and also the longitudinal forces caused by
acceleration and braking. The lateral and cross members provide resistance to lateral forces and further
increase torsional rigidity.

Advantage: Well, it has no much advantage in these days ... it is easy and cheap for hand
build, that's all.

Disadvantage: Since it is a 2 dimensional structure, torsional rigidity is very much lower than
other chassis, especially when dealing with vertical load or bumps.

Who use it ? Most SUVs, classic cars, Lincoln Town Car, Ford Crown Victoria etc.

Tubular Space Frame

TVR Tuscan Lamborghini Countach

As ladder chassis is not strong enough, motor racing engineers developed a 3 dimensional design -
Tubular space frame. One of the earliest examples was the post-war Maserati Tipo 61 "Birdcage" racing
car. Tubular space frame chassis employs dozens of circular-section tubes (some may use square-section
tubes for easier connection to the body panels, though circular section provides the maximum strength),
position in different directions to provide mechanical strength against forces from anywhere. These tubes
are welded together and forms a very complex structure, as you can see in the above pictures.

For higher strength required by high performance sports cars, tubular space frame chassis usually
incorporate a strong structure under both doors (see the picture of Lamborghini Countach), hence result in
unusually high door sill and difficult access to the cabin.

In the early 50s, Mercedes-Benz created a racing car 300SLR using tubular space frame. This also brought
the world the first tubular space frame road car, 300SL Gullwing. Since the sill dramatically reduced the
accessibility of carbin, Mercedes had to extend the doors to the roof so that created the "Gullwings".

Since the mid 60s, many high-end sports cars also adopted tubular space frame to enhance the rigidity /
weight ratio. However, many of them actually used space frames for the front and rear structure and made
the cabin out of monocoque to cut cost.

Advantage: Very strong in any direction. (compare with ladder chassis and monocoque
chassis of the same weight)

Disadvantage: Very complex, costly and time consuming to be built. Impossible for robotised
production. Besides, it engages a lot of space, raise the door sill and result in
difficult access to the cabin.

Who use it ? All Ferrari before the 360M, Lamborghini Diablo, Jaguar XJ220, Caterham, TVR
etc.

Monocoque
Today, 99% cars produced in this planet are made of steel
monocoque chassis, thanks to its low production cost and
suitability to robotised production.

Monocoque is a one-piece structure which defines the

overall shape of the car. While ladder, tubular space frame
and backbone chassis provides only the stress members
and need to build the body around them, monocoque chassis is already incoporated with the body in a
single piece, as you can see in the above picture showing a Volvo V70.

In fact, the "one-piece" chassis is actually made by welding several pieces together. The floorpan, which is
the largest piece, and other pieces are press-made by big stamping machines. They are spot welded
together by robot arms (some even use laser welding) in a stream production line. The whole process just
takes minutes. After that, some accessories like doors, bonnet, boot lid, side panels and roof are added.

Monocoque chassis also benefit crash protection. Because it uses a lot of metal, crumple zone can be
built into the structure.

Another advantage is space efficiency. The whole structure is actually an outer shell, unlike other kinds of
chassis, therefore there is no large transmission tunnel, high door sills, large roll over bar etc. Obviously,
this is very attractive to mass production cars.

There are many disadvantages as well. It's very heavy, thanks to the amount of metal used. As the shell is
shaped to benefit space efficiency rather than strength, and the pressed sheet metal is not as strong as
metal tubes or extruded metal, the rigidity-to-weight ratio is also the lowest among all kinds of chassis bar
the ancient ladder chassis. Moreover, as the whole monocoque is made of steel, unlike some other
chassis which combine steel chassis and a body made of aluminium or glass-fiber, monocoque is
hopelessly heavier than others.

Although monocoque is suitable for mass production by robots, it is nearly impossible for small-scale
production. The setup cost for the tooling is too expensive - big stamping machines and expensive
mouldings. I believe Porsche is the only sports car specialist has the production volume to afford that.

Advantage: Cheap for mass production. Inherently good crash protection. Space efficient.

Disadvantage: Heavy. Impossible for small-volume production.

Who use it ? Nearly all mass production cars, all current Porsche.

ULSAB Monocoque
Enter the 90s, as tougher safety regulations ask for
more rigid chassis, traditional steel monocoque
becomes heavier than ever. As a result, car makers
turned to alternative materials to replace steel, most
notable is aluminium. Although there is still no mass
production car other than Audi A8 and A2 to
completely eliminate steel in chassis construction,
more and more cars use aluminium in body panels
like bonnet and boot lid, suspension arms and
mounting sub-frames. Unquestionably, this is not
what the steel industry willing to see.

Therefore, American's steel manufacturers hired Porsche Engineering Services to develop a new kind of
steel monocoque technology calls Ultra Light Steel Auto Body (ULSAB). As shown in the picture, basically
it has the same structure as a conventional monocoque. What it differs from its donor is in minor details -
the use of "Hydroform" parts, sandwich steel and laser beam welding.

Hydroform is a new technique for shaping metal to desired shape, alternative to pressing. Conventional
pressing use a heavy-weight machine to press a sheet metal into a die, this inevitably creates
inhomogenous thickness - the edges and corners are always thinner than surfaces. To maintain a
minimum thickness there for the benefit of stiffness, car designers have to choose thicker sheet metal than
originally needed. Hydroform technique is very different. Instead of using sheet metal, it forms thin steel
tubes. The steel tube is placed in a die which defines the desired shape, then fluid of very high pressure
will be pumped into the tube and then expands the latter to the inner surface of the die. Since the pressure
of fluid is uniformal, thickness of the steel made is also uniformal. As a result, designers can use the
minimum thickness steel to reduce weight.

Sandwich steel is made from a thermoplastic (polypropylene) core in between two very thin steel skins.
This combination is up to 50 percent lighter compared with a piece of homogenous steel without a penalty
in performance. Because it shows excellent rigidity, it is applied in areas that call for high bending
stiffness. However, it cannot be used in everywhere because it needs adhesive bonding or riveting instead
of welding.

Compare with conventional monocoque, Porsche Engineering claimed it is 36% lighter yet over 50% stiffer.
Although ULSAB was just annouced in early 1998, the new Opel Astra and BMW 3-Series have already
used it in some parts. I believe it will eventually replace conventional monocoque.

Advantage: Stronger and lighter then conventional monocoque without increasing production
cost.
 Disadvantage: Still not strong or light enough for the best sports cars.

Who use it ? Opel Astra, BMW 3-series

Backbone Chassis

Kia's version Lotus Elan Mk

II

Colin Chapman, the founder of Lotus, invented backbone chassis in his original Elan roadster. After failed
in his experiment of glass-fibre monocoque, Chapman discovered a strong yet cheap chassis which had
been existing for millions of years - backbone.

Backbone chassis is very simple: a strong tubular backbone (usually in rectangular section) connects the
front and rear axle and provides nearly all the mechnical strength. Inside which there is space for the drive
shaft in case of front-engine, rear-wheel drive layout like the Elan. The whole drivetrain, engine and
suspensions are connected to both ends of the backbone. The body is built on the backbone, usually
made of glass-fibre.

It's strong enough for smaller sports cars but not up to the job for high-end ones. In fact, the original De
Tomaso Mangusta employed chassis supplied by Lotus and experienced chassis flex.

TVR's chassis is adapted from this design - instead of a rigid backbone, it uses a lattice backbone made of
tubular space frames. That's lighter and stronger (mainly because the transmission tunnel is wider and
higher).

Advantage: Stong enough for smaller sports cars. Easy to be made by hand thus cheap for
low-volume production. Simple structure benefit cost. The most space-saving
other than monocoque chassis.

Disadvantage: Not strong enough for high-end sports cars. The backbone does not provide
protection against side impact or off-set crash. Therefore it need other
compensation means in the body. Cost ineffective for mass production.

Who use it ? Lotus Esprit, Elan Mk II, TVR, Marcos.

Continue ...

Copyright© 1998-2000 by Mark Wan

AutoZine Technical School
Return to AutoZine home page