4 Channel RF Remote Controller with Momentary Outputs

4 Channel RF remote built using PT2262 and PT2272 IC from Princeton technology. PT2262 used as Encoder (Transmitter) and PT2262 Decoder
(Receiver) ICs are heart of the project. The receiver provides 4 channel Momentary outputs. All outputs are TTL level can be interface with other
circuits or relay board. Transmitter works with 5V to 12V DC. Receiver works with 5V DC.

When any of SW1-SW4 (S1-S4) tact switch is pressed the, power is applied to encoder IC and RF transmitter module, the encoder then starts
scanning Jumper J1-J8 and transmitting the status of the 8 bits address and data serially. The decoder IC receives the data and compares two
times with J1-J8 address jumpers and provides outputs high and also VT LED goes On, if the data is Valid and address of Transmitter and Receiver
are same. It is important to have same jumper settings J1-J8 at transmitter and receiver to pair both. Multiple remote can be used to control
devices at same location by changing the address codes. All address is Tri-State and offers 6561 combinations.

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 Encoder – Transmitter (PT2262)
PT2262 is a remote control encoder paired with PT2272 utilizing CMOS technology. Its encode data and address pins into a serial coded
waveform suitable for RF modulation. Circuit uses 8 bits of tri-state address pins providing up to 6561 address codes, thereby, drastically
reducing any code collision and unauthorized code scanning possibilities.
PT2262 encodes the code address and data set into special waveform and outputs it to the DOUT when TE is pulled to low. The wave is fed to RF
modulator (ASK RF TX Module) for transmission. The transmitted radio frequency is received by RF demodulator (ASK RF RX Module) and
reshaped to special waveform. PT2272 is then used to decode the waveform and set the corresponding output pins. Thus completing a remote
control encoding and decoding function.
Decoder Receiver (PT2272)
PT2272 decodes the waveform received and fed in to the DIN pin. The waveform is decoded into code word that contains the address, data and
sync bits. The decoded address bits are compared with the address set at the address input pins. If both address match for 2 consecutive code
words, PT2272 drives the data output pins whose corresponding data bits is the decoded to be a 1 bit, and (2) the VT output -- to high state.
VT (Valid Transmission)
When PT2272 receive a transmission code word, it initially checks weather this is a valid transmission. For a transmission to be valid, (1) it must
be complete code word, and (2) the address bits must match the address setting at the address pins. After two consecutive valid transmission,
PT2272 (1) drives the data pins according to the data bits received, and (2) raises VT to high state.
NOTE : Jumper J1 to J8, To set High Jumper provided at Bottom layer of PCB, Jumpers and closure provide to set low, don’t use any of these for
floating.

Features
· Wide Range of Operation Voltage 5V to 12V Transmitter Application
Car Security System
· Supply 5V DC Receiver
Garage Door Controller
· Single Resistor Oscillator
Remote Control Fan
· 4 Momentary Outputs
Home Security
· 4 Outputs TTL Level Automation System
· Address setting 3 states HIGH, LOW, And FLOATING) Remote Toys
· Remote provides 6561 addressable combinations by setting up J1-J8 to High, Low, and Floating. Robots
· On Board Power and Valid Transmission LEDS Remote Control for Industrial Use
· ASK Modulation
· RF link work on 433.92 MHz Frequency
· CMOS Technology
· Low Power Consumption
· Very High Noise Immunity
· Up to 8 Tri-State Code Address Pins

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 BOM TRANSMITTER
ANTENNA SR. QNTY. REF DESC.
1 1 BT1 2 PIN HEADER CONNECTOR
TX-LED 2 1 C1 0.1uf
3 1 C2 47uF/25V
4 4 D1,D2,D3,D4 1N4148
5 1 D5 3MM LED
JUMPERS J1-J8 6 8 J1,J2,J3,J4,J5,J6,J7,J8 2 PIN JUMPER
7 1 M1 ASK RF TX MODULE 433.92Mhz
8 1 RPACK1 10K 5PIN 10K RESISTOR PACK
9 1 R1 1M2
10 1 R2 1K
11 4 R3,R4,R5,R6 2K7
12 2 R7,R8 4K7 SMD 0805
13 4 SW1,SW2,SW3,SW4 TACH SWITCH
GND 14 1 SCK 18PIN IC SOCKET DIP
5V TO 12V DC 15 1 U1 78L05- TO92 REGULATOR
16 1 U2 PT2262
S1-SWITCH 1 18 8 JMP JUMPER CLOSURE
19 1 AN1 ANTENNA

BOM RECEIVER
SR. QNTY. REF DESC.
S2-SWITCH 2 1 1 ANT1 ANTENNA
2 1 CN1 2 PIN HEADER CONNECTOR
3 1 CN2 5 PIN HEADER CONNECTOR
4 1 C1 0.1uF
5 1 C2 10uF/25V
6 1 D1 3MM LED
S3-SWITCH 3
7 1 D2 3MM LED
8 8 J1,J2,J3,J4,J5,J6,J7,J8 2 PIN JUMPER
9 1 M1 ASK RF MODULE 433.92MHZ
10 1 R1 220K
11 2 R2,R3 470E
S4-SWITCH 4 12 1 U1 PT2272
13 8 JMP CLR JUMPER CLOSURE
14 1 SC 18 PIN DIP IC SOCKET

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 TRANSMITTER RECEIVER
ANTENNA
BOTTOM

POWER LED

VALID TRANSMISSION

JUMPER 1
JUMPER 2
JUMPER 3
JUMPER 4
JUMPER 5
JUMPER 6
JUMPER 7 TOP

JUMPER 8

GND
5V DC

5V DC
D3 OUTPUT
D2 OUTPUT
D3 OUTPUT
D4 OUTPUT
GND

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com