13/12/2010

AutoCAD Commands

Complete AutoCAD Commands

Command ABOUT Description Displays a dialogue box with AutoCAD version & serial numbers Controls the size of the Object Snap "OSNAP") target box -- should set to 7 Draws an arc. The default method of drawing arcs is selecting three points (socalled "3 point arc"), which are the two endpoints of the arc and some other point along its locus. Other methods of drawing an arc can be specified by three letters, such as SEA, which means "Start Point, End Point, and Included Angle." Options can be transparent

APERTURE

can be transparent

ARC or A

A Included angle C Center point of arc D Direction angle of a line tangent to the arc E Endpoint of arc L Length of chord passing thru both endpoints of the arc R Radius S Start point of arc <RET> uses the end of the last line or arc as the start point for the arc

AREA

Computes the area of any shape by selecting points at the corners of the shape, or by selecting a circle or polyline after typing or picking the "E" option

A sets "Add" mode S sets "Subtract" mode E computes area of selected circle or polyline

ARRAY

Makes multiple copies of selected objects in a rectangular (parallel with the snap rotation) or circular pattern

R rectangular array type P "polar" array type in circular pattern, you must indicate number of items and angle to fill, and whether the objects get rotated with the angle C "circular" array type in a circular pattern, you must indicate angle between items, angle to fill, and whether objects get rotated with the angle

ATTDEF

Creates an attribute definition entity for textual information to be associated with a block definition

I Controls attribute visibility C Controls Constant/variable mode V Controls verify mode P Controls preset mode

academics.triton.edu//commands.html

1/36

13/12/2010

AutoCAD Commands

ATTDISP

Controls the visibility of attribute entities on a global basis

can be transparent ON Makes all attributes visible OFF Makes all attributes invisible N Visibility of attributes set individually

ATTEDIT ATTEXT

Permits editing of attributes Extracts attribute data from drawings C CDF comma delimited format extract D DXF format extract S SDF format extract E Extracts attributes from selected entities

AUDIT

Invokes drawing integrity audit

Y Fixes errors encountered N Reports, but does not fix errors encountered

BASE

Specifies origin of current drawing for subsequent insertion into another drawing -- is normally set to point 0,0,0 Fills an automatically defined boundary with a hatch pattern through the use of dialogue boxes. Also allows previewing and replacing adjustments without starting over each time. Controls display of marker blips for point selection

can be transparent

BHATCH

BLIPMODE

can be transparent ON Enables temporary marker blips OFF Disables temporary marker blips

BLOCK

Forms a single compound entity from a group of entities within the current drawing

? Lists names of already-defined blocks in the current drawing

BPOLY

Creates a closed polyline of a boundary by picking an open area within a area enclosed by lines, arcs or circles. Erases part of a line, arc or circle, or splits it into two lines or arcs Creates a chamfer (a angled line F allows respecification of first point

BREAK

CHAMFER

D Sets chamfer distances

2/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

connection) at the intersection of two lines

P Chamfers an entire polyline

CHANGE

A multifunctioning command which can be used to alter the following: 1. location of individual endpoints of lines 2. radius of a circle 3. properties: layer, elevation, thickness, color and linetype of lines, polylines, arcs and circles 4. style, font, size, location, rotation, and wording of text entities

P Changes properties of objects C Color E Elevation LA Layer LT Linetype T Thickness

CHPROP

Modifies properties of selected objects: layer, thickness, color and linetype -- but not elevation

C Color LA Layer LT Linetype T Thickness

CIRCLE or C

Draws a circle of any size. The default method is to pick a center point and pick a point on the radius or type the radius dimension, but other methods can be selected.

2P Specifies circle by picking 2 points on the diameter 3P Specifies circle by picking 3 points through which the circle will pass D Allows entering the diameter dimension instead of radius dimension TTR Specifies circle by picking two lines, arcs or circles for the circle to be tangent to, and entering the dimension of the radius <RET> Enters radius of circle (the default)

COLOR or COLOUR

Sets the current color for subsequently drawn objects (objects drawn after the command is invoked). The default current color is a so-called "logical" color called "BYLAYER" which means that the color of the object drawn will be the color which the current layer has been set to.

can be transparent <number> sets current color to color number entered <name> sets current color to color name entered BYBLOCK sets floating entity color

academics.triton.edu//commands.html

3/36

13/12/2010

AutoCAD Commands

BYLAYER sets current color to whatever color is assigned to the current layer COMPILE Compiles shape and font files More than likely, you will never use this command, unless you are creating your own letter design or are creating "shapes" to be used as commonly used symbols in the drawing. These are not typically used in architectural drawings Displays options to allow you to reconfigure the video display, digitizer, plotter, and operating parameters. You should not have to use this command, since the configuration of your system has already been done and you will have no need to change it. COPY or CP DBLIST Lists database information for every entity in the drawing Displays a dialogue box that allows creation of an attribute definition for textual information to be associated with a block definition I Controls attribute visibility C Controls Constant/variable mode V Controls verify mode P Controls preset mode Draws a copy of selected objects using two methods -- "base point" method, or "displacement" method. M Allows multiple copies to be made of an object

CONFIG

DDATTDEF

DDATTE DDATTEXT

Allows attribute editing via a dialogue box Displays a dialogue box that extracts data from a drawing. C CDF comma delimited format extract D DXF format extract S SDF format extract E Extracts attributes from selected entities

DDCHPROP

Displays a dialogue box that modifies the color, layer, linetype, and thickness of selected objects

C Color LA Layer LT Linetype

academics.triton.edu//commands.html

4/36

13/12/2010

AutoCAD Commands

T Thickness

DDEDIT

Allows text and attribute definition editing

Undo Undoes edit to return to the previous value

DDEMODES

Sets current entity properties (layer, linetype, elevation, thickness, and text style) via a dialogue box Allows you to enable grips and set their colors and size via a dialogue box Controls dimensioning variables through a series of dialogue boxes Allows you to insert a previously made block or file into the current drawing, select X- and Y- scale factors, rotation angle, pre-explode the block, and select the insertion point, through a dialogue box Sets layer properties and allows you to set the current layer, create a new layer, freeze and thaw layers, freeze and thaw layers in the current viewport, assign or reassign colors and linetypes to layers, through a dialogue box Allows you to set running OSNAPS and set the size of the target box aperture through a dialogue box. Allows you to set drawing aids variables through a dialogue box Allows you to rename layers, text styles, linetypes, blocks, views, User Coordinate Systems, viewport configurations, and dimension styles Allows you to set entity selection modes, size of the pickbox, and entity sort method through a dialogue box Allows you to save the current User Coordinate System and give it a name for future retrieval, or to select a UCS that is already saved Allows you to set the unit type (Architectural or Decimal), angle display format (degrees-minutes-seconds, or decimal degrees), and precision of the units, This command is used with SCRIPT files.

can be transparent

DDGRIPS

can be transparent

DDIM

can be transparent

DDINSERT

DDLMODES

can be transparent

DDOSNAP

can be transparent

DDRMODES

can be transparent

DDRENAME

DDSELECT

can be transparent

DDUCS

DDUNITS

can be transparent

DELAY

can be transparent
5/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

It will delay the execution of the next command for the time in milliseconds specified after the DELAY command. DIM Takes you out of the drawing editor and into the semi-automatic dimensioning program built into AutoCAD. Will display a Dim: prompt on the command prompt line. To get back to the drawing editor and the Command: prompt, type the <Esc> key. Same as above, but only allows one dimensioning command to be used, and then takes you automatically back to the drawing editor and the Command: prompt. Dimensioning sub-command:

DIM1

DIM ALIGNED

Draws a linear dimension with the dimension line parallel to the selected dimension origin points. This lets you align a dimension with an angled line that is not either exactly horizontal or vertical.
Dimensioning sub-command:

DIM ANGULAR

Draws an arc and calculates the angle between two non-parallel lines, and draws the text and arrowheads. Arrowheads are the standard AutoCAD filled triangles, regardless of your defined Arrow Block.
Dimensioning sub-command:

DIM BASELINE

Continues a linear dimension from the baseline (the so-called "first extension line") of the previous or selected dimension. This is not frequently used in architectural dimensions. The spacing between each dimension line is controlled by the AutoCAD variable DIMDLI ("Dimension Line Increment"), which you should set at 0 normally, but if you use the baseline command, you should reset to 1/8".
6/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

DIM CENTER

Dimensioning sub-command:

Draws a pair of crossed lines at the center of a circle or arc on the current layer
Dimensioning sub-command:

DIM CONTINUE

Continues a linear dimension from the second extension line of the previous or selected dimension. It is used to create a so-called "string" of dimensions. This is used quite a bit in architectural drawings.
Dimensioning sub-command:

DIM DIAMETER

Draws a dimension through the center of a circle or arc, calculating the diameter, with one of the arrow heads located at the point on the circle or arc which is picked.
Dimensioning sub-command:

DIM EXIT

Exits the dimensioning program and returns from the Dim: prompt to the normal Command: prompt
Dimensioning sub-command:

DIM HOMETEXT

Restores the text of an associative dimension to its default (home) location if you have moved it.
Dimensioning sub-command:

DIM HORIZONTAL

Draws a horizontal linear dimension line

Dimensioning sub-command:

DIM LEADER

Draws an a line or series of lines with an arrow head (commonly called a "leader") to point to an object to notate it. This command will also prompt you for the note at the end of
7/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

the leader line, but it will allow only one line of text. The most useful method of using this command is to simply draw leaders between the object to be notated and text that you create with the DTEXT command.
DIM NEWTEXT Dimensioning sub-command:

Permits changing text of an associative dimension without exploding it. However, once the text has been changed, the dimension will no longer be associative.
Dimensioning sub-command:

DIM OBLIQUE

Adjusts the obliquing angle of a linear associative dimensions extension lines. Useful in dimensioning isometric drawings.
Dimensioning sub-command:

DIM ORDINATE

Draws the X and Y coordinates within a box with a leader line attached to the point, for a selected point. Automatically calculates the coordinates.
Dimensioning sub-command:

DIM OVERRIDE

Overrides the dimension variable settings on a selected dimension.

Dimensioning sub-command:

DIM RADIUS

Draws the radius dimension of an arc or circle from the center to the point on its locus where the arc or circle was selected.
Dimensioning sub-command:

DIM REDRAW

Redraws the viewport, just like the regular REDRAW command.

Dimensioning sub-command:
8/36

DIM

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

RESTORE

Makes a dimension style current

Dimensioning sub-command:

DIM ROTATE

Draws a linear dimension with the distance measured origin points, but with the actual dimension line set at a different angle.
Dimensioning sub-command:

DIM SAVE

Saves the currently set dimension variables under a dimension style name for future retrieval through the RESTORE command.
Dimensioning sub-command:

DIM STATUS

Lists all dimension variables with their current status.

Dimensioning sub-command:

DIM STYLE

Switches to a new Text Style for all future dimensions.

Dimensioning sub-command:

DIM TEDIT

Allows moving text in associative dimensions without having to explode the dimensions.
Dimensioning sub-command:

DIM TROTATE

Allows rotation of the text of several associative dimensions at once.

Dimensioning sub-command:

DIM UNDO

Undoes any changes made by the most recent dimensioning command.

Dimensioning sub-command:

DIM UPDATE

Changes selected associative dimensions to use the current dimension variables, the
9/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

current text style, and the current units setting.

DIM VARIABLES Dimensioning sub-command:

Lists the settings of dimension variables associated with a particular dimension style.
Dimensioning sub-command:

DIM VERTICAL

Draws a vertical linear dimension line

Finds distance between two points Places points along a line, polyline, arc, or circle, dividing it into the specified number of equal parts can be transparent B Uses a specified Block to divide the object instead of a point

DIST DIVIDE

DONUT or DOUGHNUT DRAGMODE

Draws filled rings with specified inside and outside diameters

Allows control of dynamic dragging feature for copy and move commands

can be transparent ON Makes dragging of object visible OFF Disables visual dragging A Auto mode -- enables dragging when possible

DTEXT

Draws text "Dynamically" so that as you enter text letters or numbers, they are visible on the screen

J Prompts for Justification options S Allows you to select text styles that are already created A Aligns text between two points, with style-specified width factor, AutoCAD adjusts height to keep letter proportion as designated in the style. C Centers text horizontally F Fits text between two points, with a specified height, AutoCAD adjusts width of letters to fit M Centers text horizontally and vertically R Right-justifies text

academics.triton.edu//commands.html

10/36

13/12/2010

AutoCAD Commands

BL Bottom-left justification BC Bottom-center justification BR Bottom-right justification ML Middle-left justification MC Middle-center justification MR Middle-right justification TL Top-left justification TC Top-center justification TR Top right justification

DVIEW

Allows perspective viewing of drawing

CA Sets CAmera angle relative to the Target T Sub-option, toggles between angle in the X-Y plane, and angle from the X-Y plane CL Sets Front and Back CLipping planes D Sets Camera to Target distance and turns on Perspective viewing H Removes hidden lines on the selection set OFF Turns Perspective viewing off PA PAns drawing across the screen PO Allows specification of Camera and Target points TA Rotates the TArget point about the Camera T Sub-option, toggles between angle in the X-Y plane, and angle from the X-Y plane TW Twists the view around the line of sight U Undoes a DVIEW subcommand

academics.triton.edu//commands.html

11/36

13/12/2010

AutoCAD Commands

X Exits the DVIEW command Z Sets lens length

DXBIN

Inserts specially coded binary files into the drawing Loads a drawing interchange file (DXF file) to be able to read a drawing file created by another CAD program Writes a drawing interchange file (DXF file) to be able to use an AutoCAD drawing in another CAD program B Writes binary DXF file E Outputs selected entities only (0-16) Floating point precision

DXFIN

DXFOUT

EDGESURF

Constructs a 3d Polygon mesh approximating a Coons surface patch interpolated between 4 adjoining edges Sets Elevation (distance above the ground plane) and Thickness (extruded distance from the bottom of an object to the top) for subsequently drawn entities Draws ellipses C Allows specification of Center point of ellipse rather than first axis endpoint R Allows specification of eccentricity rotation rather than length of second axis I Draws Isometric circle in current isoplane

ELEV

ELLIPSE

END

Saves the drawing and exits AutoCAD back to DOS or WINDOWS Erases selected entities from the drawing

ERASE or E EXPLODE

Separates a block, dimension or hatch pattern into its constituent entities or makes a polyline into a series of straight lines. In the case of a block that is exploded, if it was originally drawn on the 0 layer, it returns to that layer, regardless of the layer it was inserted on, and it loses its referential connection to the original block. In the case of a dimension
12/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

or hatch pattern that has been exploded, their parts go back to the 0 layer, and are assigned the logical color (BYBLOCK) regardless of the layer they were drawn on. In the case of an exploded polyline, it loses any width it may have had. EXTEND Lengthens a line, arc, or polyline to meet a specified "boundary edge" U Undoes effect of last Extend command

FILES

Allows DOS disk and file utility tasks to be done through a dialogue box Controls whether solids, traces, wide polylines, and donuts will be filled with ink. Note that fill is only visible when viewing these entities in plan (perpendicular to line of sight)

can be transparent

FILL

can be transparent ON entities visually filled with solid ink OFF entities not visually filled but are shown in outline only

FILLET

Constructs an arc of specified radius between two lines, arcs, circles, or will create arcs of the specified radius at the vertices of a polyline. Radius of the arc to be constructed may be set to 0, which will make a sharp corner

P Fillets an entire Polyline at the vertices R Allows setting of the fillet radius. Default value is 0. Radius remains set until changed again

FILMROLL

Generates a file for rendering by AutoShade, a separate program A "toggle." Flips the display on singlescreen systems (most of them) from textscreen to graphics-screen, and viceversa. Displays a rectangular grid of white dots on the screen at a specified X- and Yspacing can be transparent

GRAPHSCR

GRID

can be transparent ON Turns grid display on OFF Turns grid display off S Locks grid spacing to SNAP resolution A Sets grid aspect (different Xand Y- spacings <number> Sets grid spacing for both X- and Ycoordinates <number X> Sets grid spacing to multiple "X" of snap spacing

academics.triton.edu//commands.html

13/36

13/12/2010

AutoCAD Commands

HANDLES

Assigns a unique, permanent number to each entity of the drawing

ON Enables Handles DESTROY Discards all entity Handles

HATCH

Allows drawing of cross-hatching and pattern filling

<pattern-name> uses hatch pattern name from library file to fill designated area with a pseudo-block hatch entity -can be reduced to individual lines and points by EXPLODEing it. <*pattern-name> uses hatch pattern name from library file to fill designated area with individual lines and points, not a block U "User-defined" hatch pattern drawn of parallel lines with a specified distance between, at a specified angle, and either single-hatching or double (cross)-hatching ? Lists names of available hatch patterns <pattern-name> or U can be followed by a comma and the following sub-commands: I Ignores any boundaries inside the outermost boundary N Normal style of selecting boundaries with alternating hatched and unhatched nested areas O Hatches outermost boundary area only

HELP or ? HIDE

Displays a list of all valid commands and data entry options, or obtains help for a specific command or prompt

can be transparent if invoked while another command is in process, it will assume that you want help on that command

Regenerates a 3d visual image of the drawing with hidden lines removed Displays the X,Y, and Z coordinates of a point selected can be transparent
14/36

ID

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

IGESIN IGESOUT INSERT

Loads an IGES interchange file Writes an IGES interchange file Inserts a previously created block or drawing file into the current drawing <filename> Inserts a filename from the default directory into the current drawing, assuming that there is no block by that name in the current drawing <blockname>= <filename> Creates a block in the current drawing with the same name as the file <*name> Inserts a block in its constituent entities rather than as a block -also called a "Star Block" or Pre-exploded block C Reply to X scale prompt -allows scale to be specified by two points (Corner specification of scale) XYZ Reply to X scale prompt -allows specification of X, Y, and Z scales ~ Displays a file dialogue box ? Lists names of defined blocks within the current drawing

ISOPLANE

Selects the plane of an isometric grid to be the current plane for an orthogonal drawing

can be transparent L Left plane R Right plane T Top plane <RET> Toggle to next plane in series, Left, Right, and Top

LAYER or LA

Creates named drawing layers, assigns color and linetype properties to those layers, allows layers to be frozen and thawed, locked and unlocked, and allows current layer to be set

can be transparent C Assigns color to named layer F Freezes named layers (comma separates a list of
15/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

layers to be frozen, * can be used as a wildcard) -- current layer cannot be frozen L Assigns linetype to named layer LO Locks named layer M Makes a layer -- creates a new layer and makes it the current layer N Creates new layers with named names (comma separates a list of layers to be created, * can be used as a wildcard) ON Turns named layers on if they were turned off (comma separates a list of layers to be turned on, * can be used as a wildcard) OFF Turns named layers off if they were turned on (comma separates a list of layers to be turned off, * can be used as a wildcard) LAYER or LA (Continued) T Thaws named layers which are frozen (comma separates a list of layers to be frozen, * can be used as a wildcard) U Unlocks named layer ? Gives information about named layers, * can be used as a wildcard S Sets named layer as the current layer

LIMITS

Changes the imaginary boundaries of the drawing, and controls whether drawing can be made outside of the boundaries. If Limit-checking is ON, drawing cannot be done outside of limits.

can be transparent <2 points> Sets lowerleft and upper -right drawing limits ON Enables limit-checking OFF Disables limit-checking

LINE or

Draws straight lines

<RET> In reply to From Point: prompt, line begins at end of previous line or arc
16/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

C In reply to To point: prompt, closes the polygon back to first "From Point" U In reply to To point: prompt, undoes last line segment

LINETYPE

A linetype is a series of lines and spaces -- dots and dashes -Sets the current linetype to be used for all subsequent entities to be drawn, allows creation of new linetype definitions, and allows loading of previously created linetypes from DOS files

can be transparent ? Lists a linetype library , or named linetypes which are loaded C Creates a linetype definition L Loads a previously creatred linetype definition S Set current linetype -- note that the current linetype should always be set to the logical linetype "BYLAYER"

LIST

Lists all information about selected object, such as what type of entity it is (Line, Arc, Circle, Block, etc.), what layer it is on, what color it is, the location of its endpoints, what its Z-axis (elevation), what its thickness is, etc. Loads a file of user-defined shapes to be used with the Shape command ? Lists the names of loaded Shape files

LOAD

LTSCALE

Sets scale factor to be applied to all linetypes within the drawing Places points (or, optionally, Blocks) at intervals along a selected line, polyline, arc or circle. The interval distance is given by the user. If points are used as the marker to be placed along the entity, they are not visible unless the Point type is set to type 3 with the PDMODE command. Loads a Menu file into the menu areas (Screen, pull-down, tablet, and button) Inserts multiple copies of a Block in a rectangular pattern (word stands for "Multiple Insert." The entire array created then becomes a Block.

can be transparent

MEASURE

B specifies that a defined Block is to be used as a marker instead of a point.

MENU

MINSERT

fname Loads fname and forms a rectangular array of the resulting Block fname=f Creates Block fname from file f and forms a rectangular array

academics.triton.edu//commands.html

17/36

13/12/2010

AutoCAD Commands

? Lists names of defined Blocks within the drawing C (as a reply to X scale prompt) specifies scale via two selected points ("Corner" specification of scale) XYZ (as a reply to X scale prompt) readies Minsert for X, Y, and Z scales) - displays a file dialogue box

MIRROR

Reflects designated entities about a userspecified axis Moves designated entities to another location

MOVE or M MSLIDE

Makes a slide from the current display. Slide shows the drawing only, and not the UCSICON, the Toolbar, the Aerial View or menus. Switches to Model Space Causes the next command to repeat until cancelled Creates and controls Viewports ON Turns selected Viewports on and causes the Model to be regenerated in the selected Viewports. OFF Turns selected Viewports off and causes Model to be not displayed in the selected Viewports. Hideplot Causes hidden lines to be removed in selected Viewports during Paper Space plotting. Fit Creates a single Viewport to fit the current Paper Space view 2 Creates 2 Viewports in specified area or fit to the current Paper Space

MSPACE MULTIPLE

MVIEW

academics.triton.edu//commands.html

18/36

13/12/2010

AutoCAD Commands

view. 3 Creates 3 Viewports in specified area or fit to the current Paper Space view. 4 Creates 4 Viewports in specified area or fit to the current Paper Space view. Restore Translates viewport configurations saved with the VPORTS command into individual Viewport entities in Paper Space. <first Point> Creates a new Viewport within the area specified by 2 points. Sub-options to the "2" Option: Horizontal Creates a horizontal division between the 2 new Viewports Vertical Creates a vertical division between the 2 new Viewports. Sub-options to the "3" Option: Above Specifies placement of larger Viewport above the other 2 Below Specifies placement of larger Viewport below the other 2 Horizontal Splits area into thirds horizontally Left Specifies placement of larger Viewport to the left of the other 2 Right Specifies placement of the larger Viewport to the right of the other 2 Vertical Splits area into thirds vertically

academics.triton.edu//commands.html

19/36

13/12/2010

AutoCAD Commands

NEW

Creates a new drawing. When selected from a menu or typed in at the Command: prompt, this command brings up a dialogue box which allows setting a name for the new drawing by typing the name in the box, selection of a "prototype" drawing or typing a name of the new drawing and then an = sign and then the name of a drawing to be used as a prototype. Creates a new line, polyline arc or circle parallel to the entity and at a specified distance from it. <number> specifies offset distance T "Through" allows specification of a point through which the offset line, polyline, arc or circle is to pass

OFFSET

OOPS

restores erased entities, or entities made into a Block Opens an existing drawing Constrains drawing so that only lines aligned with the grid can be drawn -usually means only horizontal or vertical lines, however, if the crosshairs are rotated through the "Snap" "Rotate" command sequence, the lines drawn are constrained to being parallel with the crosshair rotation. Constraint can be overridden by snapping to a point or by entering exact coordinates for endpoints. Enables points to be precisely located on reference points of existing objects. This is the so-called "Running Mode" of OSNAP, which sets selection method to run continuously until set to NON (none) or until overridden by selecting another "Interrupt Mode" OSNAP method from the cursor menu. Combinations of OSNAP methods can be used by selecting a series of options separated by commas. For instance, if you want ot always pick either endpoints or intersection points when locating endpoints of lines, you would issue the command as follows: OSNAP <RET> END,INT <RET> can be transparent

OPEN ORTHO

OSNAP

can be transparent CEN CENter of arc or circle END closest ENDpoint of arc or line INS INSertion point of Text or Block INT INTersection of line, arc, or circle MID MIDpoint of line, arc, rectangle side, or polygon side NEA NEArest point selected by aperture on line, polyline, arc, or circle NOD NODe (another

academics.triton.edu//commands.html

20/36

13/12/2010

AutoCAD Commands

name for a Point) NON NONe -- used when a "Running OSNAP" is on to temporarily turn off OSNAP selection PER PERpendicular point to line, arc or circle -- when used with an arc or circle it will draw a line to the surface of the arc or circle heading toward the center point QUA QUAdrant point of arc or circle (top, bottom, right or left side) QUI QUIck mode -- this is a modifier to one of the other OSNAP options -- it will find the first point that meets the requirements, not necessarily the closest point to the aperture. TAN TANgent point to arc or circle

PAN

Moves the display window without changing the magnification factor Allows editing of polylines which are already drawn

can be transparent

PEDIT

C Closes an open polyline D Decurves, or returns a Spline curve to its control frame or series of connected straight lines E Edit vertices F Fits curve to a polyline -makes a series of straight lines into a curve which will pass through the vertices J Joins a line or arc or another polyline to an open polyline L Toggles linetype generation to be either a continuous pattern of dashes passing through the vertices, or a pattern which starts and ends at each vertex O Opens a closed polyline

academics.triton.edu//commands.html

21/36

13/12/2010

AutoCAD Commands

S Uses the polyline vertices as a frame for a Spline Curve -type of Spline Curve is set by the Variable "Splinetype." U Undoes one editing operation W Sets a uniform width for the Polyline

PEDIT (Continued)

Vertex Editing Options: B Sets first vertex for Break G "Go" -- performs a Break or Straighten operation I Inserts a new vertex after current one M Moves current vertex N Makes the Next vertex current P Makes the Previous vertex current R Regenerates the Polyline S Sets first vertex for Straighten T Sets tangent direction for current vertex W Sets new width for the following segment X Exits vertex editing, or cancels Break and Straighten

PEDIT Mesh

Allows editing of Meshes which are already drawn

D De-smooth -- restores original mesh E Edits mesh vertices M Opens (or closes) the mesh in the M direction N Opens (or closes) the mesh in the N direction S Fits a smooth surface as defined by the Variable SURFTYPE U Undoes one editing operation

academics.triton.edu//commands.html

22/36

13/12/2010

AutoCAD Commands

X Exits Pedit command Vertex Editing Options: D Makes previous vertex Down in M direction current L Makes previous vertex to Left in N direction current M Moves the marked vertex N Makes the Next vertex current P Makes the Previous vertex current R Makes next vertex to Right in N direction current RE Redisplays the polygon mesh U Makes the next vertex Up in M direction current X Exits vertex editing

PFACE

Creates a 3D mesh of arbitrary complexity and surface characteristics Puts the display in "Plan" view, with Vpoint set to 0,0,1, relative to either the current UCS, a specified UCS, or the World Coordinate System C Establishes the Plan view of the Current UCS U Establishes the Plan view of a specified UCS W Establishes the Plan view of the World Coordinate System

PLAN

PLINE

Draws a 2D polyline, which are connected line or arc segments with user-determined width and taper

H sets the half-width of the polyline segments U Undoes previous segment W sets the width of polyline segments <RET> Exits the Pline command The following options are available only as long as you are drawing in Line mode: A Switches to the Arc mode to allow integration of arcs into the polyline C Closes the polyline with

academics.triton.edu//commands.html

23/36

13/12/2010

AutoCAD Commands

straight segment L Segment length (continues previous segment) The following options are available only as long as you are in the Arc mode: A Included angle CE Center Point CL Closes with arc segment D Starting direction L Chord length, or switches to line mode R Radius S Second point of 3-point arc

PLOT

Plots a drawing to a plotting device, a printer, or to a "Plot File." Draws single points. Appearance of the points is set by the Variable PDMODE Draws regular polygons with a specified number of sides. Polygons are Polyline entities. E Specifies size and rotation of polygon by picking endpoints of one edge C Circumscribes polygon around a circle I Inscribes polygon within a circle

POINT

POLYGON

PSDRAG

Controls the appearance of an imported Postscript image that is being "dragged" (that is, positioned and scaled) into place by the PSIN command

0 Only the images bounding box is displayed as you drag it into place 1 The complete rendered PostScript image is displayed as you drag it into place

PSFILL

Fills 2D Polyline outlines with PostScript fill patterns defined in the ACAD.PSF file

. Entering a period results in no fill pattern ? Lists the fill patterns defined in ACAD.PSF file

PSIN

Imports Encapsulated PostScript (EPS) files

24/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

PSOUT

Exports the current view of your drawing to an Encapsulated PostScript (EPS) file Switches to Paper Space -- this will work only if the Variable TILEMODE is set to 0. Removes unused Blocks, Text Styles, Layers, Linetypes, and Dimension Styles from current drawing A Purges All unused named objects B Purges unused Blocks D Purges unused Dimstyles LA Purges unused LAyers LT Purges unused Linetypes SH Purges unused Shape files ST Purges unused Text Styles

PSPACE

PURGE

QSAVE

Saves the current drawing "Quickly" without requesting a filename (as long as file has already been given a name) Controls display of text -- command stands for "QuickTEXT" ON Lines of text displayed as rectangles OFF Lines of text displayed as text

QTEXT

QUIT

Exits AutoCAD -- if the current drawing has not been Saveds in its current state, a dialogue box will appear asking if you want to Save the drawing, Discard the changes, or Cancel the Exit command Attempts to recover damaged or corrupted drawings Restores a built-in command which may have been deleted by the command UNDEFINE Reverses a previous command if it was U or UNDO Refreshed or cleans up the current Viewport Redraws all viewports Regenerates the current Viewport by recalculating the vector locations of all endpoints Regenerates all Viewports
25/36

RECOVER

REDEFINE

REDO

REDRAW

can be transparent

REDRAWALL REGEN

can be transparent

REGENALL

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

REGENAUTO

Controls automatic regeneration performed by other commands

can be transparent ON Allows automatic regens OFF Prevents automatic regens

REINIT

Allows the I/O ports, the digitizer, the display, the plotter, and the ACAD.PGP file to be reinitialized. This command allows selection of what you want to reinitialize through a dialogue box. It is most useful when you make changes "on the fly" to the ACAD.PGP file and want to immediately make use of those changes without having to exit AutoCAD and get back into it. Changes the names associated with Text Styles, Layers, Linetypes, Blocks, Views, User Coordinate Systems, Viewport Configurations, and Dimension Styles. B Renames Blocks D Renames Dimension Styles LA Renames Layers LT Renames Linetypes S Renames Text Styles U Renames UCS VI Renames Views VP Renames Viewports

RENAME

RESUME REVSURF

Resumes an interrupted command script Creates a 3D polygon mesh approximating a surface of revolution, by rotating a curve around a selected axis Rotates existing objects parallel to the current UCS Restarts a command script from the beginning Requests a filename and saves the drawing Same as SAVE, but also renames the current drawing and keeps the new name current Alters the size of existing objects

can be transparent

ROTATE

RSCRIPT

SAVE

SAVEAS

SCALE

R Resizes with respect to a reference size

SCRIPT

Runs a command script. A script is a an

can be transparent
26/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

ASCII file which contains various commands that when executed operates just as if you typed in those commands, one by one, by hand SELECT Groups objects into selection sets for use in subsequent commands Allows you to display or change the setting of system variables. This command is no longer necessary to change the value of system variables. You now can type in the name of the variable to change it. Short for "SHell." Allows access to internal operating system (DOS) commands. Once SH is invoked, followed by two <RET>s, the DOS Prompt will be displayed, so you can enter any DOS command. To get back to AutoCAD, simply type EXIT at the DOS prompt. Shades 3D model in current Model Space Viewport Draws predefined Shapes ? Lists available Shape names can be transparent ? Lists specified (or all) system variables and their settings

SETVAR

SH

SHADE

SHAPE

SHELL

Allows access to internal operating system (DOS) commands. Once SH is invoked, followed by two <RET>s, the DOS Prompt will be displayed, so you can enter any DOS command. To get back to AutoCAD, simply type EXIT at the DOS prompt. Permits freehand sketching simulation C Connect: restarts SKETCH at endpoint E Erases (backs up over) temporary lines P Raises/lowers sketching pen Q Discards temporary lines, remains in SKETCH R Records temporary lines, remains in SKETCH X Records temporary lines, exits SKETCH . Draws line to current point

SKETCH

SNAP

Specified a round-off interval for point entry so that entities can be placed at precise locations

can be transparent <number> sets snap alignment resolution

27/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

ON aligns designated points OFF does not align designatged points A sets aspect ratio (differing X and Y spacing) R Rotates the snap grid and crosshairs, and turns on SNAP after, if not already turned on S Selects either Standard (rectangular) or Isometric Snap grid

SOLID

Draws filled polygons. Fill can be turned ON or OFF with the FILL command Displays drawing statistics and modes on the Text Screen Allows moving a portion of a drawing while retaining their connections to other parts of the drawing. You cannot stretch Blocks, Hatch patterns, or Text entities, however. Creates named Text styles, with userselected combinations of font, height, mirroring, obliging, and horizontal scaling. can be transparent ? Lists specified (or all) currently defined text styles can be transparent

STATUS

STRETCH

STYLE

TABLET

Aligns the digitizing tablet with coordinates of a paper drawing to accurately copy it with AutoCAD

ON Turns Tablet Mode ON (but it has to be CALibrated first) OFF Turns Tablet Mode OFF CAL Calibrates Tablet for use -sets the distance to be used to copy the drawing to an accurate scale CFG Configures tablet menus and pointing area

TABSURF

Creates a polygon mesh approximating a general tabulated surface defined by a path and a direction vector Draws text characters of any size with selected styles J Prompts for justification options S Lists or selects text style

TEXT

academics.triton.edu//commands.html

28/36

13/12/2010

AutoCAD Commands

A Aligns text between two points, with style-specified width factor, AutoCAD computes approximate height proportional to length of text line C Centers text horizontally about a defined point F Fits text between two points, with specified height, AutoCAD computes approximate width factor to fill the distance between the two points M Centers text horizontally and vertically about a defined point R Right-justifies text BL Bottom Left justification BC Bottom Center justification BR Bottom Right justification ML Middle Left justification MC Middle Center justification MR Middle Right justification TL Top Left justification TC Top Center justification TR Top Right justification

TEXTSCR

A "toggle." Flips the display on singlescreen systems (most of them) from textscreen to graphics-screen, and viceversa. Displays drawing creation and update times, and permits control of an elapsed timer.

can be transparent

TIME

can be transparent D Displays current times ON Starts user elapsed timer OFF Stops user elapsed timer R Resets user elapsed timer

TRACE

Draws solid filled lines of specified width. Has mostly been superseded by the PLINE command. Displays information on the drawing's
29/36

TREESTAT

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

current spatial index, such as the number and depth of nodes in the drawing database. TRIM Erases a portion of selected entities that cross a specified "cutting edge" Reverses the effect of the previous command Defines or modifies the current User Coordinate System D ("Delete") Deletes one or more saved coordinate systems E ("Entity") Sets a UCS with the same extrusion direction as that of the selected entity O ("Origin") Shifts the origin of the current coordinate system P ("Previous") Restores the Previous UCS R ("Restore") Restores a previously saved UCS S ("Save") Saves the current UCS V ("View") Establishes a new UCS whose Z-axis is parallel to the current viewing direction W ("World") Sets the current UCS to the World Coordinate System X Rotates the current UCS around the X-axis Y Rotates the current UCS around the Y-axis Z Rotates the current UCS around the Z-axis ZA Defines a UCS using an origin point and a point on the positive portion of the Z-axis 3 Defines a UCS using an origin point, a point on the positive portion of the X-axis, and a point on the positive Yportion of the XY plane ? Lists specified saved coordinate systems U Undoes last trim operation

UCS

academics.triton.edu//commands.html

A Changes settings of all active 30/36

13/12/2010

AutoCAD Commands

UCSICON

Controls visibility and placement of the User Coordinate System Icon, which graphically indicates the origin and orientation of the current UCS. The options normally affect only the current viewport.

A Changes settings of all active viewports N ("NoOrigin") Displays the UCSICON at the lower-left corner of the viewport (i.e., not at the Origin) OR ("ORigin") Displays the UCSICON at the origin of the current UCS, if possible (if the origin point is not within the current viewport, the location of the UCSICON defaults to the lower-left corner of the viewport) OFF Turns the UCSICON off ON Turns the UCSICON on

UNDEFINE

Deletes the definition of a built-in AutoCAD command Reverses the effect of multiple commands, and provides control over the "Undo" facility <number> Undoes the <number> of most recent commands in reverse order A ("Auto") Controls treatment of menu items as UNDO "Groups" B ("Back") Undoes back to previous UNDO "Mark" C ("Control") Enables/disables the UNDO feature E ("End") Terminates an UNDO Group (a sequence to be treated as one command) G ("Group") Begins an UNDO Group (a sequence to be treated as one command) M ("Mark") Places "marker" in UNDO file (for use with "Back") Control Sub-Options All Enables the full UNDO feature None Disables U and UNDO entirely, and discards any previous UNDO information saved earlier in the editing session One Limits U and UNDO

UNDO

academics.triton.edu//commands.html

31/36

13/12/2010

AutoCAD Commands

to a single operation UNITS Selects coordinate and angle display formats and precision Saves the current graphic display and space as a named view, or restores a saved view and space to the display can be transparent

VIEW

can be transparent D Deletes a named view R Restores named view to screen S Saves current display as named view W Saves specified Window as named view ? Lists specified named views

VIEWPORTS or VPORTS

Used in Model Space only, and has been superseded by Paper Space Vports, created with the MVIEW command. Divides the AutoCAD graphics display into multiple viewports, each of which can contain a different view of the current drawing (maximum of 4 "tiled" viewports per viewport)

D Deletes a saved viewport configuration J Joins (merges) two viewports R Restores a saved viewport configuration S Saves the current viewport configuration SI ("SIngle") Displays a SIngle viewport filling the entire graphics area 2 Divides the current viewport into 2 viewports 3 Divides the current viewport into 3 viewports 4 Divides the current viewport into 4 viewports ? Lists the current and saved viewport configurations

VIEWRES

Allows you to control the precision and speed of circle and arc drawing on the monitor by specifying the number of sides in a circle. Acts like an AutoCAD variable. Recommend that it be set to 2000. Sets viewport visibility for new and existing layers ? Lists layers frozen in a selected viewport F ("Freeze") Freezes specified layers in selected viewports

VPLAYER

academics.triton.edu//commands.html

32/36

13/12/2010

AutoCAD Commands

T ("Thaw") Thaws specified layers in selected viewports R ("Reset") Resets specified layers to their default visibility N ("Newfrz") Creates new layers that are frozen in all viewports V ("Vpvisdflt") Sets the default viewport visibility for existing layers VPOINT Selects the viewpoint for a 3D visualization R Selects viewpoint via two rotation angles <RET> Selects viewpoint via a graphic compass and axis tripod which appears on the screen <x,y,z> Specifies x, y, and z relative coordinates of viewpoint

VSLIDE

Displays a previously created slide file

<filename> views slide with name of "filename.SLD" *filename preloads slide which the next command VSLIDE will view

WBLOCK

Writes selected entities or previously created Block to a drawing file

<filename> writes specified entities to "filename.DWG" = filename.DWG to be created is same as the entities included in a previously defined Block by the same name * writes entire drawing to the filename.DWG and purges all unreferenced blocks, layers, linetypes, text and dimensioning styles <RET> writes selected objects

XBIND

Makes portions of an Xref a permanent

B ("Block") Makes a block in

33/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

part of your drawing

B ("Block") Makes a block in the Xref a permanent part of your drawing D ("Dimstyle") Makes a dimstyle in the Xref a permanent part of your drawing L ("Layer") Makes a layer in the Xref a permanent part of your drawing LT ("LType") Makes a Ltype in the Xref a permanent part of your drawing S ("Style") Makes a text style in the Xref a permanent part of your drawing

XREF

Allows you to work with other AutoCAD drawings without adding them permanently to your drawing and without altering their contents

A ("Attach") "Attaches" a new Xref to the drawing or updates an Xref that is already attached B ("Bind") Makes an Xref a permanent part of your drawing D ("Detach") Removes an Xref from your drawing P ("Path") Allows you to view and edit the filename path (directory and sub-directory) that AutoCAD searches when loading a particular Xref R ("Reload") Updates one or more Xrefs at any time ? Lists Xrefs in your drawing and the drawing associated with each one

ZOOM

Enlarges or reduces the display magnification of the drawing, without changing the actual size of the entities

can be transparent <number> multiplier from original magnification <number X> multiplier from current magnification <number XP>multiplier of magnification relative to paper space -- used for plotting to get right plot scale in each viewport A ("All") fills limits of drawing to

academics.triton.edu//commands.html

34/36

13/12/2010

AutoCAD Commands

screen C ("Center") makes picked point the center of the screen D ("Dynamic") makes an adjustible rectangular lens appear on the screen which is capable of being made smaller or larger and moved to different positions over the drawing and once set by the user, the drawing will quickly zoom to the location and magnification set for the lens. This subcommand is no longer useful because all computers have very fast zooms naturally now. E ("Extents") makes the farthest edges of the actual visible drawing fill up the graphics screen L ("Lower-Left") makes the point picked become shoved to the lower-left corner of the graphics screen P ("Previous") zooms back to whatever the last zoom, previous to the current zoom was -- AutoCAD stores about 10 of these, so you can walk backward in zoom magnification 10 times V ("Virtual Screen") makes the largest area available to the graphics card fill the graphics screen -- this varies with the quantity of graphics RAM that your graphics card has W ("Window") asks you to pick the lower left corner and the upper right corner of a zoom window and then fits that window to the graphics screen

3DFACE

Draws flat planes in 3D space with either 3 corners or 4 corners (3 sided or 4 sided flat planes). These are used to hide objects behind them in space to create the illusion of a solid object. 3DFACEs can also be shaded using the SHADE command, in which case the entire plane takes on the color assigned to its edges. Normally (without using the HIDE or SHADE commands, 3DFACEs are transparent, which means that objects

I ("Invisible") this is used by typing in the letter "I" just before picking a corner point for the 3DFACE, and it will make the edge of the 3DFACE drawn from that point to the next one "Invisible" (that is, it will not be shown as a line on the drawing). This is important when joining several 3DFACEs together to cover a complex,
35/36

academics.triton.edu//commands.html

13/12/2010

AutoCAD Commands

behind them in space are visible through them, and they appear as "wireframes."

multi-faceted surface, where you do not want the "seams" of the 3DFACEs to show in the final drawing. The visibility of edges of 3DFACEs can further be turned on or off by the AutoCAD variable "SPLFRAME." When SPLFRAME is set to 1 ("on"), both edges which have been made "Invisible" as well as normal, visible edges are shown on the drawing. When SPLFRAME is set to 0 ("off"), Invisible edges are not shown. The purpose of sometimes wanting to see invisible edges is that you may want to move, stretch, or copy the 3DFACE and if its edges are invisible, you cannot select them fopr modification. You can only select a 3DFACE by picking on a visible edge.

3DMESH

Draws a 3D polygon mesh by specifying its size, in terms of the number of faces in each direction (called M and N directions), and the location in 3D space of each vertex (the corner of a face) in the mesh. Creates a 3D polyline C Closes the polyline back to the first point U Undoes (deletes) the last segment entered <RET> Exits 3DPOLY command

3DPOLY

academics.triton.edu//commands.html

36/36