2012 KX250F Owners Manual

Downloaded from www.Manualslib.
com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
GENERAL INFORMATION j
Quick Reference Guide
This Quick Reference Guide will assist you in MAINTENANCE AND ADJUSTMENT j
finding the information you’re looking for.
TROUBLESHOOTING GUIDE j
TUNING j
STORAGE j
A Table of Contents is included after the

Foreword.

IMPORTANT INFORMATION
• This vehicle is designed for the operator only, no passengers.

• This vehicle is a competition model only and was not manufactured for use on public streets, roads or
highways.
• The use of this vehicle should be limited to participation in sanctioned competition events upon a closed
course.
• This vehicle should not be used for general off-road recreational riding.
• Read owner’s manual.

Whenever you see the symbols shown below, IMPORTANT NOTICE
heed their instructions! Always follow safe operat-
THIS VEHICLE IS A COMPETITION MODEL
ing and maintenance practices.
ONLY AND WAS NOT MANUFACTURED
DANGER FOR, NOR SHOULD IT BE USED ON, PUB-
LIC STREETS, ROADS, OR HIGHWAYS. THE
DANGER indicates a hazardous situation USE OF THIS VEHICLE SHOULD BE LIMITED
which, if not avoided, will result in death or TO PARTICIPATION IN SANCTIONED COMPE-
serious injury. TITION EVENTS UPON A CLOSED COURSE.
THIS VEHICLE SHOULD NOT BE USED FOR
GENERAL OFF-ROAD RECREATIONAL RIDING.
WARNING READ OWNER’S MANUAL.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury. WARNING
THIS VEHICLE SHOULD NOT BE USED FOR
GENERAL OFF-ROAD RECREATIONAL RID-
NOTICE ING.
NOTICE is used to address practices not re-
lated to personal injury. DISCLAIMER OF WARRANTY
This motorcycle is sold AS IS, with all faults,
NOTE obvious or concealed and there are NO WAR-
This note symbol indicates points of particular in- RANTIES, expressed or implied. Including war-
terest for more efficient and convenient operation. ranties of MERCHANTABILITY or FITNESS FOR
PURPOSE.
The purchaser accepts all responsibilities con-
cerning quality, performance, cost of service
and/or necessary repairs.

Motorcycle Noise Emission Control
Information
This motorcycle is designed for closed course
competition use only. It does not conform to
U.S. EPA motorcycle noise standards.
NOTICE
Off-road motorcycling is a wonderful sport, and
we hope you will enjoy it to the fullest. How-
ever, if improperly conducted, this sport has
the potential to cause environmental problems
as well as conflicts with other people. Respon-
sible use of your off-road motorcycle will en-
sure that these problems and conflicts do not
occur. TO PROTECT THE FUTURE OF YOUR
SPORT, MAKE SURE YOU USE YOUR MOTOR-
CYCLE LEGALLY, SHOW CONCERN FOR THE
ENVIRONMENT, AND RESPECT THE RIGHTS
OF OTHER PEOPLE.

FOREWORD
Congratulations on your choosing this Kawasaki motorcycle. Your new motorcycle is the product of
Kawasaki’s advanced engineering, exhaustive testing, and continuous striving for a superior lightweight,
high-performance machine with superb handling and stability for racing and sporting use.
Your new KX is a highly tuned competition machine for participation in racing events. As with any mechan-
ical device, proper care and maintenance are important for trouble-free operation and top performance. This
manual is written to enable you to keep your KX properly tuned and adjusted.
Due to improvements in design and performance made during production, in some cases there may be minor
discrepancies between the actual vehicle and the illustrations and text in this manual.
KAWASAKI HEAVY INDUSTRIES, LTD.

Motorcycle & Engine Company
© 2011 Kawasaki Heavy Industries, Ltd. Apr. 2011. (1)

TABLE OF CONTENTS
SPECIFICATIONS............................................ 7 Drive Chain.................................................... 82
GENERAL INFORMATION.............................. 10 Handlebar...................................................... 89
Location of Parts ........................................... 10 Brakes ........................................................... 90
Side Stand..................................................... 13 Steering ......................................................... 94
Fuel ............................................................... 14 Front Suspension .......................................... 97
Fuel Requirement:...................................... 14 Rear Suspension (UNI-TRAK®)..................... 139
Kick Pedal ..................................................... 16 Wheels .......................................................... 145
Starting the Engine ........................................ 17 Hoses Inspection........................................... 147
Shifting Gears................................................ 18 Tightening Torques of Nuts and Bolts............ 148
Stopping the Motorcycle................................ 19 Cleaning Your Motorcycle.............................. 153
Stopping the Engine ...................................... 20 Lubrication..................................................... 155
Break-In......................................................... 20 DFI Self-Diagnosis ....................................... 158
Daily Pre-Ride Checks .................................. 22 TROUBLESHOOTING GUIDE......................... 164
After-Race Checks ........................................ 24 TUNING............................................................ 171
MAINTENANCE AND ADJUSTMENT............. 25 Suspension.................................................... 171
Periodic Maintenance Chart .......................... 25 Gearing.......................................................... 177
Engine Oil...................................................... 30 Special Care According to Track Conditions . 178
Cooling System ............................................. 35 OPTIONAL PARTS .......................................... 179
Spark Plug..................................................... 39 PRE-RACE CHECKS AND AFTER-RACE
Air Cleaner .................................................... 46 MAINTENANCE ............................................ 180
Throttle Cable ................................................ 52 STORAGE........................................................ 182
Throttle Body Assy ........................................ 53 Before Storage .............................................. 182
Clutch ............................................................ 66 After Storage ................................................. 183
Valve Clearance ............................................ 73 ENVIRONMENTAL PROTECTION.................. 184
Exhaust System ............................................ 78 WIRING DIAGRAM .......................................... 185

SPECIFICATIONS 7
SPECIFICATIONS
DIMENSIONS
Overall Length 2 170 mm (85.4 in.)
Overall Width 820 mm (32.3 in.)
Overall Height 1 270 mm (50.0 in.)
Wheelbase 1 475 mm (58.1 in.)
Road Clearance 330 mm (13.0 in.)
Curb Mass 106.1 kg (234 lb)
Fuel Tank Capacity 7.2 L (1.9 US gal)
ENGINE
Type 4-stroke, DOHC, single-cylinder, liquid-cooled
Bore × Stroke 77.0 × 53.6 mm (3.0 × 2.1 in.)
Displacement 249 cm³ (15.2 cu in.)
Compression Ratio 13.5:1
Fuel System FI (Fuel Injection)
Starting System Primary kick
Ignition System Digital DC-CDI
Ignition Timing 4° BTDC @2 000 r/min (rpm)
Lubrication System Forced lubrication (semi-dry sump)
Spark Plug NGK CPR8EB-9
Spark Plug Terminal Solid-post

8 SPECIFICATIONS
TRANSMISSION
Transmission Type 5-speed, return shift
Clutch Type Wet, multi disc
Driving System Chain drive
Gear Ratio:
1st 2.142 (30/14)
2nd 1.750 (28/16)
3rd 1.444 (26/18)
4th 1.235 (21/17)
5th 1.045 (23/22)
Primary Reduction Ratio 3.350 (67/20)
Final Reduction Ratio 3.846 (50/13)
Overall Drive Ratio 13.470 @Top gear
Engine Oil:
Type API SG, SH, SJ, SL or SM with JASO MA, MA1 or MA2
Viscosity SAE 10W-40
Capacity 1.0 L (1.1 US qt)
FRAME
Type Tubular, semi-double cradle
Steering Angle 42° to either side
Caster 28.2°
Trail 120.2 mm (4.7 in.)

SPECIFICATIONS 9
Tire Size/Type:
Front 80/100-21 51M/BRIDGESTONE M403
Rear 100/90-19 57M/BRIDGESTONE M404
Rim Size:
Front 21 × 1.60
Rear 19 × 1.85
Suspension:
Front Telescopic fork (upside-down)
Rear New Uni-trak® swingarm
Front Suspension Travel 315 mm (12.4 in.)
Rear Wheel Travel 310 mm (12.2 in.)
Front Fork Oil:
Type SHOWA SS19
Capacity (Left Front Fork):
Cylinder Unit 260 mL (8.79 US oz.)
Outer Tube 374 mL (12.6 US oz.)
Capacity (Right Front Fork) 205 mL (6.93 US oz.)
BRAKES
Type:
Front Single disc
Rear Single disc
Specifications are subject to change without notice.

10 GENERAL INFORMATION
j
GENERAL INFORMATION
Location of Parts
1. Clutch Lever 3. Fuel Tank Cap 5. Front Brake Lever

2. Engine Stop Button 4. Front Brake Fluid Reservoir 6. Throttle Grip

GENERAL INFORMATION 11
j
1. Front Fork 6. Upstream Injector 11. Shift Pedal

2. Radiator 7. Seat 12. Rear Shock Absorber
3. Fuel Tank 8. Air Cleaner Element 13. Swingarm
4. Throttle Body Assy 9. Brake Disc 14. Drive Chain
5. Downstream Injector 10. Brake Caliper 15. Chain Guide

j
1. Muffler 5. Uni-Trak® Tie-Rod and Rocker Arm

2. Rear Brake Fluid Reservoir 6. Oil Level Gauge
3. Rear Shock Absorber Gas Reservoir 7. Rear Brake Pedal
4. Kick Pedal 8. Exhaust Pipe

j
NOTE
Side Stand Support the motorcycle with a suitable stand to
perform maintenance or adjustment procedures.
To install the side stand, insert its flat end into the
rear axle as shown in the figure.
A. Side Stand
B. Rear Axle
WARNING
Riding with the side stand can cause a crash
resulting in injury. Do not start the engine or
attempt to ride the motorcycle when the side
stand is installed.

j
WARNING
Fuel Gasoline is extremely flammable and can be
explosive under certain conditions. Always
This Kawasaki KX has a 4-stroke engine that re-
stop the engine and do not smoke. Make
quires a gasoline.
sure the area is well-ventilated and free from
The capacity of the fuel tank is 7.2 L (1.9 US gal).
any source of flame or sparks; this includes
To open the fuel tank cap, pull out the breather hose
any appliance with a pilot light. Never fill
from the hole in the steering stem, and turn the tank
the tank so the fuel level rises into the filler
cap counterclockwise.
neck. If the tank is overfilled, heat may cause
the fuel to expand and overflow through the
vents in the tank cap. After refueling, make
sure the fuel tank cap is closed securely. If
gasoline is spilled on the fuel tank, wipe it off
immediately.
Fuel Requirement:
Fuel Type
Use clean, fresh unleaded gasoline with a mini-
mum Antiknock Index of 90. The Antiknock Index is
posted on service station pumps in the U.S.A. The
octane rating of a gasoline is a measure of its re-
sistance to detonation or “knocking”. The Antiknock
A. Fuel Tank Cap Index is an average of the Research Octane Num-
B. Breather Hose ber (RON) and the Motor Octane Number (MON) as
shown in the table below.
Minimum
Octane Rating Method
Rating
(RON + MON)
Antiknock Index 90
2

j
NOTICE products such as corn), also known as “gasohol” is
approved for use.
If engine “knocking” or “pinging” occurs,
use a different brand of gasoline of a higher NOTICE
octane rating.
If this condition is allowed to continue it can Avoid using blends of unleaded gasoline and
lead to severe engine damage. methanol (wood alcohol) whenever possible,
Gasoline quality is important. Fuels of low and never use “gasohol” containing more
quality or not meeting standard industry than 5% methanol. Fuel system damage and
specifications may result in unsatisfactory performance problems may result.
performance. Operating problems that result
from the use of poor quality or nonrecom- Gasoline/Ether Blends - The most common ether
mended fuel may not be covered under your is methyl tertiary butyl ether (MTBE). You may use
warranty. gasoline containing up to 15% MTBE.
NOTE
Fuels Containing Oxygenates Other oxygenates approved for use in unleaded
Gasoline frequently contains oxygenates (alco- gasoline include TAME (up to 16.7%) and ETBE
hols and ethers) especially in areas of the U.S. and (up to 17.2%). Fuel containing these oxygenates
Canada which are required to sell such reformu- can also be used in your Kawasaki.
lated fuels as part of a strategy to reduce exhaust
emissions.
The types and volume of fuel oxygenates ap-
proved for use in unleaded gasoline by the U.S.
Environmental Protection Agency include a broad
range of alcohols and ethers, but only two compo-
nents have seen any significant level of commercial
use.
Gasoline/Alcohol Blends - Gasoline containing up
to 10% ethanol (alcohol produced from agricultural

j
NOTICE
Never use gasoline with an octane rat-
Kick Pedal
ing lower than the minimum specified by
This motorcycle is equipped with a primary kick
Kawasaki.
starting system. When the clutch lever is pulled, the
Never use “gasohol” with more than 10%
motorcycle can be started with the transmission in
ethanol, or more than 5% methanol. Gaso-
any gear.
line containing methanol must also be
blended with cosolvents and corrosion
inhibitors.
Certain ingredients of gasoline may cause
paint fading or damage. Be extra careful
not to spill gasoline or gasoline oxygenate
blends during refueling.
When not operating your Kawasaki for 30
to 60 days, mix a fuel stabilizer (such as
STA-BIL) with the gasoline in the fuel tank.
Fuel stabilizer additives inhibit oxidation of
the fuel which minimizes gummy deposits.
Never store this product with “gasohol” in
the fuel system. Before storage it is recom-
mended that you drain all fuel from the fuel
system. See the Storage section in this man- A. Kick Pedal
ual.

j
When engine is cold -
Starting the Engine •Pull out the idle adjusting screw/choke knob.
• Shift the transmission into neutral.

WARNING
Riding with the side stand can cause a crash
resulting in injury. Do not start the engine or
attempt to ride the motorcycle when the side
stand is installed.
NOTICE
This motorcycle is designed for competition
use only. Therefore, the radiator does not
incorporate a coolant reserve tank or cool-
ing fan. Prolonged idling of the engine with A. Idle Adjusting Screw/Choke Knob
no airflow through the radiator can cause
coolant loss and engine overheating result- • Find the kick pedal position around the top so that
the resistance to depress the kick pedal is fully felt
ing in possible engine damage. Any riding
conditions that increase engine temperature by pushing down the kick pedal slowly.
will further reduce idling time before coolant • Kick the engine over, leaving the throttle closed.
loss occurs. These conditions include high NOTE
ambient temperature, sandy or muddy ter-
rain, or other conditions causing high engine When the clutch lever is pulled, the motorcycle can
be started with the transmission in any gear.
loads at low speeds. Furthermore, warming
the engine up excessively before operation,
or leaving idling with the hot engine temper-
• Even after the engine has started, do not push
back immediately the idle adjusting screw/choke
ature after operation results in the engine knob until the engine is thoroughly warmed up.
overheating, too.
When engine is already warm or restarts -
•Kick the engine over, leaving the throttle closed
without using the idle adjusting screw/choke knob.

j
NOTE
If the engine fails starting, open the throttle fully Shifting Gears
and depress the kick pedal slowly about 4 a 5
times to clear too rich fuel mixtures in the engine. This motorcycle is equipped with a 5-speed “return
Then, kick the engine over, leaving the throttle shift” transmission. The neutral is located halfway
closed. between 1st and 2nd gear. “Return shift” means
that when shifting up or down, each gear must be
engaged before the next higher or lower gear may
be selected.
• To engage first gear from the neutral position, pull
in the clutch lever and push down on the shift
pedal, gently release the clutch lever, then release
the shift pedal.
• To shift up to the next gear, pull in the clutch lever,
lift the shift pedal with your toes, gently release the
clutch lever, and then release the shift pedal.
• To shift down to the next gear, pull in the clutch
lever, push the shift pedal down as far as it will go,
gently release the clutch lever, then release the
shift pedal.
NOTICE
When changing gears, press firmly on the
shift pedal to ensure proper shifting. Care-
less, incomplete shifting can cause the
transmission to jump out of gear and lead to
engine damage.

j
Stopping the Motorcycle
For maximum deceleration, close the throttle and
apply both front and rear brakes. Pull in the clutch
lever as the motorcycle comes to a stop. Indepen-
dent use of the front or rear brake may be advanta-
geous in certain circumstances. Shift down progres-
sively to ensure good engine response at all speeds.
A. Shift Pedal

j
Stopping the Engine Break-In
• Close
Shift the transmission into the neutral position. A brief break-in procedure must be carried out to
• stop button.
the throttle completely and push the engine obtain the proper operating clearances in the engine
and transmission, which are necessary for perfor-
mance and reliability.
NOTICE
For the first hour or 20 km (12 mile) of op-
eration, run the engine at low and moderate
engine speeds. See details below.
Break in the engine as follows.

1. Start the engine and let it idle until it is thor-
oughly warmed up.
2. Ride the motorcycle for about 20 minutes within
1/2 throttle opening.
3. Stop and let the engine cool completely. Be
sure to check the tightness of nuts and bolts,
A. Engine Stop Button oil leakage, and any irregularities.
4. Start the engine and ride the motorcycle for
about 40 minutes within 3/4 throttle opening.
5. Stop and let the engine cool completely. Be
sure to fully check the tightness of nuts and
bolts, oil leakage, and any irregularities, espe-
cially, each cable elongation, brake play, chain
slack and spoke tightness.
6. Change the engine oil, oil filter and front
fork/rear shock absorber oil to the new one.
7. After the break-in procedure has been properly
carried out, the motorcycle is ready for regular

j
operation. Using the proper riding skills and NOTICE
techniques and avoiding recklessly high engine
When any following parts have been re-
speeds will keep the engine trouble-free.
placed, the same break-in procedure as the
new motorcycle must be carried out for one
hour or 20 km (12 mile):
Cylinder, Piston, Piston pin, Piston ring,
Valve, Valve lifter, Camshaft, Crankshaft,
Mission gear, etc.

j
Daily Pre-Ride Checks
Check the following items each day before you ride. The time required is minimal, and habitual performance
of these checks will help ensure a safe, reliable ride.
If any irregularities are found during these checks, refer to the appropriate section and take the action required
to return the motorcycle to a safe operating condition.
WARNING
Failure to perform these checks before operation may result in serious damage or an accident. Al-
ways perform daily safety checks before operation.
DANGER
Exhaust gas contains carbon monoxide, a colorless, odorless poisonous gas. Inhaling carbon
monoxide can cause serious brain injury or death. DO NOT run the engine in enclosed areas. Op-
erate only in a well-ventilated area.
Engine
Engine Oil .................................... No leakage
Level correct
Coolant ........................................ No leakage
Level correct (engine cold)
Radiator Cap ............................... Properly installed
Spark Plug ................................... Correctly torqued
Cylinder Head Cover ................... Correctly torqued
Clutch .......................................... Functions properly
Air Cleaner .................................. Clean
Apply oil to air cleaner element
Properly installed
Muffler ......................................... No damage

j
Properly installed
Engine Sprocket .......................... No wear or damage
Frame
Tires ............................................ Overall condition good
No wear or damage
Pressure correct
Air valve cap installed
Spokes ........................................ No looseness
Drive Chain ................................. Overall condition good
Chain slack correct
Oil if necessary
Front and Rear Brakes ................ Function properly
Lever and pedal play correct
No fluid leakage
Throttle ........................................ Functions properly
Throttle grip returns smoothly
Steering ....................................... Smooth but not loose from lock to lock
No binding due to control cables
Front Fork .................................... Functions properly
No oil leakage
Rear Shock Absorber .................. Functions properly
No oil leakage
Fuel Tank ..................................... Mounted securely
No fuel leakage
Rear Sprocket ............................. No wear or damage
Engine Stop Button ..................... Functions properly
Nuts, Bolts, Fasteners ................. Properly tightened

j
Carry out the general lubrication and make neces-
After-Race Checks sary adjustments.
After racing, first clean the motorcycle, then in-

spect the entire motorcycle with special attention to
the air cleaner, brakes, etc.

MAINTENANCE AND ADJUSTMENT 25
MAINTENANCE AND ADJUSTMENT

j
Periodic Maintenance Chart
The maintenance and adjustments outlined in this chapter are easily carried out and must be done in accor-
dance with the Periodic Maintenance Chart to keep the motorcycle in good running condition.
1. Periodic Inspection (Engine Related Item)
FREQUENCY After each Every 3 Every 6 Every 12
As See
race (or races (or races (or races (or
required Page
OPERATION 2.5 hours) 7.5 hours) 15 hours) 30 hours)
Throttle cable - inspect and adjust • 52
Valve clearance - inspect † • 73
Clutch plates - inspect † • 69
Spark plug - clean and inspect † • 39
Clutch - inspect • 66
Air cleaner element - clean † • 48
Throttle body assy - inspect and adjust • 53
K Cylinder head, cylinder - inspect • –
K Crankshaft - inspect • –
Muffler - clean and inspect † • 78
Kick pedal and shift pedal - clean • –
Engine sprocket - inspect † • 88

26 MAINTENANCE AND ADJUSTMENT

As See
required Page
j OPERATION 2.5 hours) 7.5 hours) 15 hours) 30 hours)
Coolant level - inspect • 35
Breather hose - inspect • –
Water hoses and connections - inspect
† • 35

2. Periodic Inspection (Chassis Related Item)

As See
race (or races (or races (or races (or j
required Page
OPERATION 2.5 hours) 7.5 hours) 15 hours) 30 hours)
Brake - adjust † • 90
Brake pad wear - inspect † • 93
Brake fluid level - inspect † • 91
Spoke tightness and rim runout -
inspect † • 145
Drive chain - inspect and adjust • 82

Drive chain - lubricate • 88
Drive chain wear - inspect † • 85
Front fork - clean and inspect • 97
Nuts, bolts, fasteners - inspect † • 148
K Fuel system - clean • –
Fuel hose, connections - inspect † • 147
Brake hoses, connections - inspect † • 147
Steering play - inspect † • 94
K Steering stem bearing - lubricate • –
Rear sprocket - inspect † • 88
General lubrication - perform • 155
K Wheel bearing - inspect † • –


As See
required Page
j OPERATION 2.5 hours) 7.5 hours) 15 hours) 30 hours)
Swingarm and UNI-TRAK linkage
K
pivots - inspect † • –
Swingarm and UNI-TRAK linkage

K
pivots - lubricate • –
Frame - inspect • –
Wheels/tires - inspect • 145
Rear shock absorber - inspect • 139
Cable - inspect • –

3. Periodic Replacement (Engine and Chassis Related Item)

See
race (or 2.5 races (or 7.5 races (or 15 races (or j
Page
OPERATION hours) hours) hours) 30 hours)
Engine oil - change • 31
Oil filter - replace • 31
K Piston and piston ring - replace • –
K Piston pin - replace • –
Silencer wool - replace • 78
Spark plug - replace • 40
K Brake fluid - change Every 2 years –
Brake master cylinder cup and dust cover –
K Every 2 years
- replace
Brake caliper fluid seal and dust seal - –
K Every 2 years
replace
K Brake hoses - replace Every 4 years –
Front fork oil - change • 102
K Fuel hose - replace Every 5 years –
K Rear shock absorber oil - change • –
†: Replace, add, adjust, clean or torque if necessary.

K: Should be serviced by referring to the Service Manual or an authorized Kawasaki dealer.

NOTICE
Engine Oil Racing the engine before the oil reaches ev-
j In order for the engine, transmission and clutch
ery part can cause engine seizure.
to function properly, maintain the engine oil at the
proper level, and change the oil and oil filter period- Oil Level Inspection
ically.
Not only do dirt and metal particles collect in the
• Ifsitthea few
oil has just been changed, let the motorcycle
minutes allowing the oil to settle.
oil, but the oil itself loses its lubricative quality if used
too long.
• idle speed.
Start the engine and run it for several minutes at
Do not run the engine at high en-
gine speed.
WARNING • Stop the engine and wait several minutes for the
Motorcycle operation with insufficient, de- oil to settle.
teriorated, or contaminated engine oil will • Check the engine oil level with the motorcycle ver-
tical through the oil level gauge on the lower right
cause accelerated wear and may result in en-
gine or transmission seizure, accident, and side of the engine. The oil level should come up
injury. Check the oil level before each ride between the high and low level lines next to the
and change the oil according to the periodic gauge.
maintenance chart in the Owner’s Manual. NOTE
Because of the semi-dry sump lubrication system, If the oil level is too high, remove the excess oil
the engine oil level indicated on the oil level gauge using a syringe or other suitable device.
will fluctuate depending on the motorcycle’s position If the oil level is too low, add the correct amount
and engine speed when the engine’s shut off. To of oil through the oil filler opening. Use oil of the
ensure a proper reading of the engine oil level, follow same type and brand as those of the one that is
the Oil Level Inspection procedures closely. already in the engine.

NOTE • Warm up the engine thoroughly so that the oil will

pick up any sediment and drain easily.
If no oil appears in the oil level gauge, tip the mo-
torcycle slightly to the right until oil is visible then • Stop the engine, and place a container beneath it.
j
return to an upright position. If no oil appears • Remove the
Remove the oil filler plug.
even when tipped at an extreme angle, remove the • perpendicularoiltodrain bolt and position the vehicle
the ground to allow all the oil to
drain bolt to empty any oil that may be in the trans-
mission and crankcase, reinstall the drain bolt and drain.
refill with the specified amount of oil.
A. Drain Bolt
A. Oil Level Gauge WARNING

B. High Level Line
C. Low Level Line Motor oil is a toxic substance. Dispose of
D. Oil Filler Plug used oil properly. Contact your local author-
ities for approved disposal methods or pos-
Oil and/or Oil Filter Change sible recycling.
The engine oil and/or oil filter should be changed
periodically to ensure long engine life.

• When the oil filter is replaced, remove the oil filter • Replace the oil filter element with a new one.
cover bolts and take off the cover with O-ring and • Install the oil filter
Apply grease to the grommet.
j spring. • ward the engine. element with the grommet to-
NOTICE
Inside-out installation stop oil flow, causing
engine seizure.
A. Oil Filter Cover

B. Bolts
A. Oil Filter Element

B. Grommet

• Install the spring to the oil filter cover. Tightening Torque

• a new O-ring
Install the oil filter cover with the grease applied to
and tighten its bolts to the specified
Engine Oil Drain Bolt:
20 N·m (2.0 kgf·m, 15 ft·lb) j
torque.
NOTE
Replace the gasket and O-ring with a new one.
• Fill the engine up to the high level line with good
quality engine oil specified in the table.
Recommended Engine Oil
Castrol “Power 1 R4 Racing” 5W-40 or
“Kawasaki Performance 4-Stroke Full Synthetic
Oil*” 10W-40 or
“Kawasaki Performance 4-Stroke
Semi-Synthetic Oil*” 10W-40 or
“Kawasaki Performance 4-Stroke Motorcycle
Oil*” 10W-40
A. Spring
B. O-ring *Kawasaki Performance Oils and Lubricants have
C. Oil Filter Cover been specifically engineered for your vehicle. Con-
sistent use of these products meets or exceeds war-
Tightening Torque ranty and service requirements and can help to ex-
tend the life of your Kawasaki.
Oil Filter Cover Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb) Engine Oil Capacity
Capacity:
• After the oil has completely drained out, install the
drain bolt with its new gasket. Proper torque for it
0.75 L (0.79 US qt) (When filter is not removed)
0.80 L (0.85 US qt) (When filter is removed)
is shown in the table. 1.00 L (1.06 US qt) (When engine is completely
dry)

NOTE The oil viscosity may need to be changed to ac-
If unavailable, use equivalent engine oil in accor- commodate atmospheric conditions in your riding
dance with the following table. area.
j
Type:
API SG, SH, SJ, SL or SM with JASO MA, MA1
or MA2
Viscosity:
SAE 10W-30, 10W-40, 10W-50
NOTE
Do not add any chemical additive to the oil. Oils
fulfilling the above requirements are fully formu-
lated and provide adequate lubrication for both the
engine and the clutch.
• Tighten the oil filler plug.

Tightening Torque
Oil Filler Plug:
5.0 N·m (0.51 kgf·m, 44 in·lb)
• Start the engine.

• Check the oil level and oil leakage.

WARNING
Cooling System The cooling system can get extremely hot
during normal operation and cause serious j
Water Hoses burns. Do not touch the radiator when it is
Check the water hoses for cracks or deterioration, hot, nor open the radiator cap. Hot coolant
and the connections for looseness in accordance inside will cause severe burns.
with the Periodic Maintenance Chart.
Radiator NOTE
Check the radiator fins for obstruction by insects or The coolant originally filled into the cooling sys-
mud. Clean off any obstructions with a low-pressure tem contains 50% of a permanent, ethylene-glycol
stream of water. -based antifreeze, has a freezing point of –35°C
(–31°F) and a green appearance.
NOTICE
Using high-pressure water, as from a car Coolant Level Inspection
wash facility, could damage the radiator fins • Remove the bolts and right radiator shroud.
and impair the radiator’s effectiveness.
Do not obstruct or deflect airflow by in-
stalling unauthorized accessories in front of
the radiator.
Interference with the cooling airflow can lead
to overheating and consequent engine dam-
age.
Coolant
Coolant absorbs excessive heat from the engine
and transfers it to the air through the radiator. If
the coolant level becomes low, the engine overheats
and may suffer severe damage. Check the coolant
level each day before riding the motorcycle, and re-
plenish coolant if the level is low. A. Bolts
B. Right Radiator Shroud

• Situate the motorcycle perpendicular to the

ground until the radiator cap is level to the ground,
so that the radiator cap is located uppermost
j in order to exhaust the air accumulated in the
radiator.
• Remove the radiator cap in two steps.
• First, turn the cap counterclockwise to the first stop
and wait there for a few seconds.
• Then, push and turn the cap further in the same
direction and remove it.
A. Coolant Level
B. Filler Neck
• Ifradiator
the coolant level is low, add coolant through the
filler opening to the bottom of the filler
neck.
Water and Antifreeze Mixing Ratio
1:1 (water:antifreeze)
Recommended Antifreeze
A. Radiator Cap Permanent type of antifreeze (ethylene glycol
• Check the coolant level in the radiator. The
coolant should come up to the bottom of the
plus corrosion and rust inhibitor chemicals for
aluminum engines and radiators)
radiator filler neck.
NOTE Coolant Total Amount
Check the coolant level when the engine is cold 1.2 L (1.3 US qt)
(room or ambient temperature).

• Install the radiator cap and right radiator shroud.

• Tighten the bolts.
Tightening Torque j
Radiator Shroud Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
Coolant Change
The coolant should be changed to ensure long en-
gine life, if necessary.
• Wait for the engine to cool completely.
• Situate the motorcycle perpendicular to the
ground until the radiator cap is level to the ground.
• Remove the radiator cap in two steps.
• Drain the coolant from the engine and radiator in
the following way.
A. Coolant Drain Bolt
B. Water Pump Cover
• Place a container under the coolant drain bolt on
the water pump cover and remove the drain bolt. NOTICE
Immediately wash away any coolant that
spills on the frame, engine, or wheel.
WARNING
Coolant on tires will make them slippery
and can cause loss of traction resulting in
an accident and injury. Thoroughly clean
any coolant that might have splashed on the
tires.
• Visually inspect the old coolant.

• Ifparts
whitish cotton-like wafts are observed, aluminum
in the cooling system are corroded and the
NOTICE
Use coolant containing corrosion inhibitors
system must be flushed.
j made specifically for aluminum engines and
• If the coolant is brown, iron or steel parts are rust-
ing and the system must be flushed.
radiators in accordance with the instruction
of the manufacture. Soft or distilled water
• Check the cooling system for damage, loose con-
nections, and leaks.
must be used with the antifreeze in the cool-
ing system. If hard water is used in the sys-
• Install the coolant drain bolt with its new gasket
at the water pump cover and apply the specified
tem, it causes scale accumulation in the wa-
ter passages, and considerably reduces the
torque.
efficiency of the cooling system.
NOTE
Always replace a gasket with a new one. NOTE
Tightening Torque Pour in the coolant slowly so that it can expel the
air from the engine and radiator.
Coolant Drain Bolt:
7.0 N·m (0.71 kgf·m, 62 in·lb) • Install the radiator cap.
• Start thetheengine
Check cooling system for leaks.
• Fill the radiator up to the bottom of the radiator filler
neck with coolant.
• stop it. and warm up thoroughly, then
• Lean the motorcycle slightly until the radiator filler

neck is level to the ground so that the filler neck
• Check the coolant level after the engine has
cooled down. The coolant should come up to the
is located uppermost in order to exhaust the air bottom of the radiator filler neck.
accumulated in the radiator. • If the coolant level is low, add coolant up to the
bottom of the radiator filler neck.
• Install the radiator cap.
• Check the cooling system for leaks.

If the plug is oily or has carbon built up on it, clean

Spark Plug it (preferably with a sandblaster) and then clean
off any abrasive particles. The plug may also be
The spark plug should be taken out periodically for cleaned using a high-flash point solvent and a wire
j
inspection and regapping. Measure the gap with a brush or other suitable tool. If the spark plug elec-
wire-type thickness gauge. If incorrect, adjust the trodes are corroded, or damaged, or if the insulator
gap to the specified value by bending the outer elec- is cracked, replace the plug. The standard spark
trode. plug is shown in the table below.
Spark Plug Gap Standard Spark Plug
CPR8EB-9 NGK CPR8EB-9
0.8 a 0.9 mm (0.031 a 0.035 in.)
CPR9EB-9
To find out whether the plug’s heat range is correct,
remove the plug and examine the ceramic insulator
around the center electrode. If the ceramic is light
brown, the spark plug correctly matches the engine
temperature.
If the ceramic is burned white, the plug should be
replaced with a colder plug.
Optional Spark Plug
Colder NGK CPR9EB-9
NOTE
If the engine performance drops, try replacing the
spark plug to regain performance.
A. Gap
B. Outer Electrode

Spark Plug Removal and Installation • Remove the fuel tank mounting bolt and band.
• Remove the seat (see Air Cleaner section).
j • Remove the bolts and take off the radiator shroud
on both sides.
A. Fuel Tank Mounting Bolt

B. Band
A. Bolts
B. Radiator Shroud

• Be sure to place a piece of cloth around the fuel • Turn the driver to disconnect the joint lock.
hose joint. • Pull the fuel hose joint out of the outlet pipe.
• Insert a thin blade screwdriver into the slit on the
joint lock.
j
A. Turn
B. Joint Lock
A. Cloth C. Fuel Hose Joint
B. Thin Blade Screwdriver
C. Joint Lock

• Disconnect the fuel pump lead connector. • Clean the cylinder head cover around the spark
• Remove the fuel tank. plug cap hole before removing the spark plug.
j • Pull the spark plug cap off the plug before remov-
ing the spark plug.
A. Fuel Pump Lead Connector
WARNING A. Spark Plug Cap
Gasoline is extremely flammable and can be • Apply a suitable wrench to the spark plug.
explosive under certain conditions. • When reinstalling
Loosen and remove the spark plug.
Always stop the engine and do not smoke.
Make sure the area is well-ventilated and free
• ification. the spark plug, torque it to spec-
from any source of flame or sparks; this in- Tightening Torque

cludes any appliance with a pilot light.
Spark Plug:
13 N·m (1.3 kgf·m, 115 in·lb)

• Install the spark plug cap as shown in the figure. not fixed completely, reattach them with an adhe-
• installation
Pull up the plug cap lightly to make sure of the
of the spark plug cap.
sive. If the dampers are damaged, replace them
with new ones.
j
A. Spark Plug Cap A. Dampers

B. Front
• Make sure that the dampers are in place on the

frame and are not damaged. If the dampers are

• Insert the fuel hose joint straight onto the fuel out-
let pipe until the hose joint clicks.
• Push and pull the fuel hose joint back and forth
more than two times, and make sure it is locked
j • Push the joint lock until the hose joint clicks. and does not come off.
A. Fuel Hose Joint A. Fuel Hose Joint

B. Joint Lock B. Push and Pull
NOTICE WARNING
When installing the fuel hose joint, do not Leaking fuel can cause a fire or explosion
apply strong force to the outlet pipe on the resulting in serious burns. Make sure the
fuel pump. The pipe made from resin could hose joint is installed correctly on the deliv-
be damaged. ery pipe by sliding the joint.
NOTE
If it comes off, reinstall the fuel hose joint.
• Before installing the fuel tank, check that both
throttle cables run over the black connector.

NOTE • After installing the fuel tank, make sure that both
throttle cables (outer) move slightly by pulling
To prevent the bottom of the fuel tank from pushing them back and forth in the upper space of the
the throttle cables, run the throttle cables over the j
black connector correctly. right side of the fuel tank. Check that both throttle
cables run under the frame (right side) as shown
in the figure.
A. Throttle Cables
B. Black Connector A. Throttle Cables
• Hook the band to the fuel tank. B. Fuel Tank
C. Bottom of the Frame (Right Side)
• Tighten the fuel tank mounting bolt.
• Install the removed parts.
NOTE
Insert the fuel tank breather hose outlet end into
the steering stem hole.

NOTE
Air Cleaner In dusty areas, the element should be cleaned
j more frequently than recommended interval.
A clogged air cleaner restricts the air intake, in- After riding through rain or on muddy roads, the
creases fuel consumption, reduces engine power, element should be cleaned immediately.
and can cause spark plug fouling. Inspect the air
intake system, which includes the air filter and air Element Removal and Inspection
duct to the throttle body assy, and the duct clamps
and throttle body assy, before each race or practice • Remove the bolts on the right and left sides.
session.
WARNING
If dirt or dust is allowed to pass through into
the throttle body assembly, the throttle may
become stuck, possibly causing accident.
Be sure to keep the dust from entering dur-
ing cleaning.
NOTICE
A clogged air cleaner will affect fuel mixture
to the engine and reduce engine power and
cause spark plug fouling. A. Bolts

• Open the both side covers slightly outward and

slide the seat rearward.
• Remove
element.
the wing bolt, and take out the air cleaner
A. Side Covers A. Air Cleaner Element

B. Seat B. Wing Bolt
• Check inside of the intake tract and throttle body

assy for dirt. If dirty, clean the intake tract and
throttle body assy thoroughly.
• Stuff a clean, lint-free towel into the throttle body
assy to keep dirt from entering the throttle body
assy.
• Wipe out the inside of the air cleaner housing with
a clean, damp towel.
• Take the element off its frame.
NOTICE
Do not twist or wring the element, as it gets
easily torn or damaged.

• Inspect the element. If it is dirty, clean it. Also

check if the element is in good condition (no tears,
hardening or shrinkage). If damaged, replace the
j element or it will allow dirt into the throttle body
assy.
WARNING
A clogged air cleaner may allow dirt and dust
to enter the throttle body assembly and the
throttle may stick resulting in a hazardous
operating condition. Clean the air cleaner ac-
cording to the periodic maintenance chart;
more often if the motorcycle is used in ex-
tremely dusty conditions.
A. Air Cleaner Element
B. Element Frame
NOTICE
Element Cleaning and Installation
A clogged air cleaner may allow dirt and dust
to enter the engine, causing it to wear exces- • Clean the element in a bath of a high-flash point
solvent or hot soapy water. Rinse the element with
sively or to become damaged. clear water to remove all traces of the cleaning
solution.
• Squeeze the element dry in a clean towel.
NOTICE
Do not twist, wring or blow the element dry
to avoid damaging it.

WARNING
Gasoline and low-flash point solvents can
be flammable and/or explosive and cause j
severe burns. Clean the element in a
well-ventilated area, and take care that there
is no spark or flame anywhere near the work-
ing areas. Do not use gasoline or low-flash
point solvents to clean the element.
• After cleaning, let the filter dry completely. Satu-

rate the element with a high-quality foam air fil-
ter oil and make sure that the oil is evenly ap-
plied throughout the element. Squeeze out the ex-
cess oil, but do not wring the element as this could
cause tearing. In this case, too much oil is better
than too little. Finally pat the inside of the element
with a paper towel to remove any excess oil.
• Before installation, check the element for damage
such as tears, hardening, or shrinkage. If dam-
aged, replace the element.
• Apply grease to all mating surfaces and to the
screw hole in the air cleaner housing and intake
tract.
• Remove the towel from the throttle body assy.
• Install the element onto its frame, and coat the
element lip and lip seat with a thick layer of all
-purpose grease to assure a complete seal.

• Install the air cleaner element so that its tab faces

upward and its projections align with the holes in
the housing.
j
A. Apply grease.
A. Tab
B. Projections
C. Holes
• Tighten the wing bolt.

• Insert the hooks of the seat under the flange collar

and brackets.
• Install the tabs of the side covers into the inside of
the seat, and tighten the bolts.
j
A. Hooks A. Tabs
B. Seat B. Seat
C. Flange Collar
D. Brackets • Pull up the rear end of the seat to make sure it is
securely installed.

Throttle Cable
• Ifupper
the play is incorrect, loosen the locknut on the
end of the throttle cable and turn the ad-
juster to obtain the specified play. Then, tighten
j the locknut toward the adjuster.
Throttle Cable Adjustment
Inspect the throttle grip for smooth operation in
all steering positions. Check and adjust the throttle
cable in accordance with the Periodic Maintenance
Chart.
• Check that the throttle grip has 2 a 3 mm (0.08 a
0.12 in.) of play and turns smoothly.
A. Adjusters
B. Locknuts
• With the engine idling, turn the handlebar both

ways and check if handlebar movement changes
the idle speed. If so, the throttle cable may be
improperly adjusted or incorrectly routed, or dam-
A. Throttle Grip aged. Be sure to correct any of these conditions
B. 2 a 3 mm (0.08 a 0.12 in.) before riding.

WARNING
Operation with improperly adjusted, incor-
Throttle Body Assy
rectly routed, or damaged cables could re- j
sult in an unsafe riding condition. Be sure Idle Speed Adjustment
the control cables are adjusted and routed • Thoroughly warm up the engine.
correctly, and are free from damage. • the idle speedadjusting
Turn the idle screw/choke knob to adjust
2 000 a 2 100 r/min (rpm) by using
the engine revolution tester (The tester should be
followed by the method described by the manufac-
ture.).
A. Idle Adjusting Screw/Choke Knob

B. Tester
• Open and close the throttle a few times to make

sure the idle speed does not change, and readjust
if necessary.
• With the engine idling, turn the handlebar both
ways and check if handlebar movement changes

the idle speed. If so, the throttle cable may be im- Cleaning the Throttle Body Assy
properly adjusted, incorrectly routed, or damaged. • Remove the seat (see Air Cleaner section).
j Be sure to correct any of these conditions before • Remove the fuel
Remove the tank (see Spark Plug section).
riding. • both sides. bolt and take off the side cover on
WARNING
Operation with damaged cables could result
in an unsafe riding condition. Replace dam-
aged control cables before operation.
NOTICE
This motorcycle’s radiator does not incorpo-
rate cooling fan. Prolonged idling of the en-
gine with no airflow through the radiator can
cause coolant loss and engine overheating
resulting in possible engine damage. Any
riding conditions that increase engine tem-
perature will further reduce idling time be-
fore coolant loss occurs. These conditions A. Bolt
include high ambient temperature, sandy or B. Side Cover
muddy terrain, or other conditions causing
high engine loads at low speeds. Further-
more, warming the engine up excessively be-
fore operation, or leaving idling with the hot
engine temperature after operation results in
the engine overheating, too.

• Loosen the muffler clamp bolt. • Loosen the air cleaner duct clamp screw.
• the mufflerthebody
Remove muffler mounting bolts, and pull out
rearward.
j
A. Air Cleaner Duct Clamp Screw
A. Muffler Clamp Bolt

B. Muffler Mounting Bolts
C. Muffler Body

• Disconnect the intake air temperature sensor con-

nector and upstream injector connector.
• Be sure to place a piece of cloth around the fuel
hose joint.
j • Open the both tabs of the joint lock outward and
slide the joint lock downward.
• Pull
pipe.
the fuel hose joint out of the upstream injector
A. Intake Air Temperature Sensor Connector

B. Upstream Injector Connector
A. Tabs
B. Fuel Hose Joint
C. Cloth

• Remove the rear frame mounting bolts on the left

and right sides.
• Be sure to place a piece of cloth around the fuel
hose joint.
• Pull the rear frame rearward with the air cleaner
housing.
• Insert a thin blade screwdriver into the slit on the
joint lock.
j
A. Rear Frame Mounting Bolts A. Cloth

B. Air Cleaner Housing B. Thin Blade Screwdriver
C. Joint Lock

• Turn the driver to disconnect the joint lock. • Disconnect the throttle sensor connector.
• Pull the fuel hose joint out of the delivery pipe.
j
A. Throttle Sensor Connector

A. Turn
B. Joint Lock
C. Fuel Hose Joint

• Disconnect
tor.
the intake air pressure sensor connec- • Free the main harness from the clamps.
• Disconnect the downstream injector connector. j
A. Main Harness
B. Clamps
A. Intake Air Pressure Sensor Connector
B. Downstream Injector Connector

• Loosen the throttle body assy holder clamp screw. • Remove the bolts and clamps, and take off the
• Pull the throttle body assy from the holder. throttle pulley cover.
j
A. Throttle Body Assy Holder Clamp Screw A. Throttle Pulley Cover Bolts
B. Throttle Pulley Cover

• Loosen the throttle cable bolts, and free the tips of

throttle cable lower end.
• Clean the throttle body assy (see Cleaning Your
Motorcycle section).
NOTICE j
If dirt gets through into the engine, exces-
sive engine wear and possibly engine dam-
age will occur.
• Lubricate the lower ends of the throttle cables and

reinstall them in reverse order of removal.
Tightening Torque
Throttle Cable Bolts:
3.5 N·m (0.36 kgf·m, 31 in·lb)
Throttle Pulley Cover Bolts:
3.4 N·m (0.35 kgf·m, 30 in·lb)
A. Tips of Throttle Cable Lower End
B. Throttle Pulley WARNING
C. Accelerator Cable
D. Decelerator Cable Operation with improperly adjusted, incor-
E. Throttle Cable Bolts rectly routed, or damaged cables could re-
sult in an unsafe riding condition. Be sure
• After removing the throttle body assy, cover the
throttle body assy holder and air cleaner duct with the control cables are adjusted and routed
a clean cloth to protect them from dirt. correctly, and are free from damage.

• Install the throttle body assy to the throttle body

assy holder. Align the projection with the groove.
• Hold the main harness to the clamps.
j • Check the throttle body assy is installed securely.
A. Main Harness
B. Clamps
A. Groove
B. Projection

• Insert
pipe.
the fuel hose joint straight onto the delivery • Push and pull the fuel hose joint back and forth
• Check the yellow paint of the hose in the throttle
body assy side.
and does not come off.
j
• Push the joint lock until the hose joint clicks.
A. Fuel Hose Joint

B. Push and Pull
A. Fuel Hose Joint
B. Yellow Paint WARNING
C. Joint Lock
Leaking fuel can cause a fire or explosion
resulting in serious burns. Make sure the
NOTICE hose joint is installed correctly on the deliv-
When installing the fuel hose joint, do not ery pipe by sliding the joint.
apply strong force to the delivery pipe on the
throttle body assy. The pipe made from resin NOTE
could be damaged.
If it comes off, reinstall the fuel hose joint.

• Connect the intake air pressure sensor connector,

upstream injector connector, downstream injector
• Tighten the rear frame mounting bolts to the spec-
ified torque.
connector and throttle sensor connector.
j Tightening Torque
• Install the rear frame with the air cleaner housing
to the throttle body assy. Rear Frame Mounting Bolts:
34 N·m (3.5 kgf·m, 25 ft·lb)
• Check the duct is installed securely.
• Check the clamp position as shown in the figure.
• Insert the fuel hose joint straight onto the upstream
injector pipe.
• Check the yellow paint of the hose in the upstream
injector pipe side.
• Push the joint lock until the hose joint clicks.
A. Clamp
• Tighten the clamp screws securely.

Tightening Torque
Throttle Body Assy Holder Clamp Screw: A. Fuel Hose Joint
2.0 N·m (0.20 kgf·m, 18 in·lb) B. Yellow Paint
Air Cleaner Duct Clamp Screw: C. Joint Lock
2.0 N·m (0.20 kgf·m, 18 in·lb)

NOTICE WARNING
When installing the fuel hose joint, do not Leaking fuel can cause a fire or explosion re-
apply strong force to the upstream injector sulting in serious burns. Make sure the hose j
pipe. The pipe made from resin could be joint is installed correctly on the upstream in-
damaged. jector pipe by sliding the joint.
• Push and pull the fuel hose joint back and forth
NOTE
and does not come off. If it comes off, reinstall the fuel hose joint.
• Connect the intake air temperature sensor con-
nector and the upsteam injector connector.
• Check the duct is installed securely.
• Open and close the throttle a few times to make
sure the grip operates correctly.
• Check
justment.
the throttle cable play and idle speed ad-
A. Fuel Hose Joint

B. Push and Pull

If the clutch lever free play cannot be adjusted at
Clutch the clutch lever, make the adjustment further down
the cable as follows.
j
Clutch Lever Adjustment • Remove the number plate (see Steering section).
Proper clutch lever free play is 8 a 13 mm (0.3 a • Turn the adjuster in all the way.
0.5 in.). Lever play increases with cable stretch and • Slide the dust cover back.
friction plate wear, requiring periodic adjustment. • Loosen the locknut in the middle of the clutch ca-
ble, and turn the adjusting nut so that the clutch
When the clutch lever free play is out of specifica-
lever free play is 8 a 13 mm (0.3 a 0.5 in.).
tion, first try adjusting it at the clutch lever as follows.
• Turn the adjuster to obtain the proper amount of
clutch lever free play.
A. Dust Cover
B. Locknut
C. Adjusting Nut
A. Clutch Lever
B. Adjuster
C. 8 a 13 mm (0.3 a 0.5 in.)
• Tighten the locknut.

WARNING
Too much cable play can prevent clutch dis-
engagement and cause an accident resulting j
in serious injury or death. When adjusting
the clutch or replacing the cable, be sure the
upper end of the clutch outer cable is fully
seated in its fitting, or it could slip into place
later, creating enough cable play to prevent
clutch disengagement.
NOTE
After the adjustment is made, start the engine and
check that the clutch does not slip and that it re-
leases properly. A. Brake Pedal Bolt
B. Brake Pedal
C. Return Spring
Friction and Steel Plates Removal
• Drain the engine oil (see Engine Oil section).
• pedal return
Remove the brake pedal bolt and the rear brake
spring.

• Remove the clutch cover bolts. • Remove the clutch cover and gasket.
• plate andthe
Remove clutch spring bolts, clutch pressure
springs.
j
A. Bolts
B. Clutch Cover
A. Clutch Spring Bolts
B. Clutch Pressure Plate

• Remove the friction and steel plates. Steel Plate Thickness Measurement
Standard 1.5 a 1.7 mm (0.059 a 0.067 in.)
Service Limit 1.4 mm (0.055 in.) j
A. Friction Plate
B. Steel Plate
Friction and Steel Plates Wear/Damage A. Thickness

Inspection B. Friction Plate
• Visually inspect the friction and steel plates to see
if they show any signs of seizure, or uneven wear. Friction and Steel Plate Warp Inspection
• Iffriction
any plates show signs of damage, replace all
plates and steel plates as a set. • Place each friction plate and steel plate on a sur-
face plate, and measure the amount of friction
• plates withthevernier
Measure thickness of the friction and steel
calipers.
plate and steel plate warp with a thickness gauge
(i.e., the gap between the surface plate and each
• them with new ones. the service limit, replace
If they have worn past friction plate or steel plate).
Friction Plate Thickness Measurement

• If any plate is warped over the service limit, re-
place it with a new one.
Standard 2.72 a 2.88 mm (0.107 a 0.113 in.)
Service Limit 2.5 mm (0.10 in.)

Friction and Steel Plate Warp Friction and Steel Plate Installation
0.15 mm • Install all parts in the reverse order of removal.
j Friction Plate
Standard
(0.0059 in.) or less • ing between
Install the friction plates and steel plates, alternat-
the two; be sure to start and finish
Service Limit 0.3 mm (0.012 in.) with a friction plate.
0.15 mm
Standard
Steel Plate (0.0059 in.) or less
Service Limit 0.3 mm (0.012 in.)
A. Friction and Steel Plates
NOTICE
A. Surface Plate
If dry steel plates and friction plates are in-
B. Friction or Steel Plate stalled, apply engine oil to the surfaces of
C. Thickness Gauge each plate to avoid clutch plate seizure.

• Apply molybdenum disulfide grease to the steel

ball and the contact area of the push rod holder.
• Check the release shaft lever position by measur-
ing the position distance between the lever and the
• Install the steel ball and the push rod holder. cable bracket while pushing the release shaft lever
lightly forward.
j
A. Apply molybdenum disulfide grease.

B. Push Rod Holder A. Release Shaft Lever
C. Steel Ball B. Push forward.
C. Position Distance
• Install the clutch pressure plate and springs. D. Cable Bracket
• torque. the clutch spring bolts to the specified
Tighten
• Iflectthethelever position is not within the standard, se-
correct thickness of adjusting washer ac-
Tightening Torque
cording to the following table.
Clutch Spring Bolts:
9.0 N·m (0.92 kgf·m, 80 in·lb) • Remove the push rod holder as necessary and
reinstall the clutch.

Release Shaft Lever Position and Adjusting
Washer Selection
j Position Judg- Washers Quan-
Distance ment Thickness tity
49.2 a 56.5 mm 1.5 mm
Standard 1
(1.94 a 2.22 in.) (0.06 in.)
More than 56.5 1.0 mm
Too big 1
mm (2.22 in.) (0.04 in.)
Less than 49.2 1.0 mm
Too small 2
mm (1.94 in.) (0.04 in.)
• Place a new clutch cover gasket in position with a

thin layer of grease and tighten the bolts.
A. Adjusting Washer
B. Push Rod Holder Tightening Torque
C. Needle Bearing Clutch Cover Bolts:
D. Circlip 9.8 N·m (1.0 kgf·m, 87 in·lb)
Adjusting Washer
Thickness Part Number
• When installing the brake pedal, apply the grease
to the contact area of the brake pedal pivot.
1.5 mm (0.06 in.) 92200-1548 • Install the removed parts.
1.0 mm (0.04 in.) 92200-0045 • Check the engine oil level.

Valve Clearance Inspection

Valve Clearance • Remove
tion).
the spark plug cap (see Spark Plug sec-
j
Valve and valve seat wear decreases valve clear-
ance, upsetting valve timing.
• Remove the cylinder head cover bolts and cylinder
head cover.
NOTICE
If valve clearance is left unadjusted, wear will
eventually cause the valves to remain partly
open, which lowers performances, burns the
valves and valve seats, and may cause seri-
ous engine damage.
Valve clearance for each valve should be checked

and adjusted in accordance with the Periodic Main-
tenance Chart.
NOTE
If the engine is hot, wait until the engine cools.
Valve clearance must be checked when the en- A. Cylinder Head Cover Bolts and Washers
gine is cold (room temperature). B. Cylinder Head Cover

• Remove the head cover gasket and spark plug

hole gasket.
• Remove the two caps from the magneto cover.
j
A. Timing Inspection Cap

A. Head Cover Gasket B. Flywheel Nut Cap
B. Spark Plug Hole Gasket

• Bring the piston to the Top Dead Center (TDC) of

its compression stroke to inspect the valve clear-
• Atsprockets
this point, the timing marks on the camshaft
must be almost aligned with the cylinder
ance (the position at the end of the compression head upper surface as shown in the figure.
stroke) by aligning the top mark with the groove
j
on the magneto cover while turning the crankshaft
counterclockwise.
A. Timing Mark
B. Camshaft Sprockets
C. Cylinder Head Upper Surface
A. Top Mark
B. Groove on Magneto Cover
C. Crankshaft
D. Crankshaft Rotation Direction

• Using the thickness gauge, measuring the clear-

ance between each cam lobe and valve lifter, for
• Ifrange,
the valve clearance is not within the specified
adjust by an authorized Kawasaki dealer or
all four valves. a competent mechanic following the instructions in
j the Service Manual.
NOTE
Record the measured valves clearance. • Using a high-flash point solvent, clean off any oil
or dirt that may be on the silicone sealant coating
area. Dry them with a clean cloth.
• Apply silicone sealant to the cylinder head as
shown in the figure.
A. Thickness Gauge
Standard Valve Clearance

Exhaust 0.17 a 0.22 mm (0.0067 a 0.0087 in.) A. Silicone Sealant
Intake 0.10 a 0.15 mm (0.0039 a 0.0059 in.)

• Replace the head cover gasket with a new one. • Make sure that the upper chain guide is bottomed
• Replace the
Install the head cover gasket on the cylinder head. to the cylinder head cover.
• one, and installspark
it.
plug hole gasket with a new
j
A. Upper Chain Guide

B. Cylinder Head Cover
A. Head Cover Gasket
B. Spark Plug Hole Gasket NOTICE
Unless the upper chain guide is bottomed,
the camshaft chain could push the cylinder
head cover upward, leading to an oil leak.
• Install the cylinder head cover.

• the cylinder
Install the washer with the metal side upwards to
head cover, and tighten the bolts to
the specified torque.

Tightening Torque
Cylinder Head Cover Bolts: Exhaust System
j 9.8 N·m (1.0 kgf·m, 87 in·lb)
The exhaust system, in particular the muffler body,
• Install the two caps to the magneto cover. is designed to reduce exhaust noise and conduct the
exhaust gases away from the rider while minimizing
Tightening Torque power loss. If carbon has built up inside the muffler
Timing Inspection Cap: body, exhaust efficiency is reduced, causing engine
3.9 N·m (0.40 kgf·m, 35 in·lb) performance to drop.
Flywheel Nut Cap: If the muffler body is badly damaged, dented,
4.9 N·m (0.50 kgf·m, 43 in·lb) cracked or rusted, replace it. Replace the silencer
wool if the exhaust noise becomes too loud or en-
• Install the removed parts. gine performance drops.
Silencer Wool Replacement
• Remove the bolts and right side cover.
A. Bolts
B. Right Side Cover

• Remove the muffler cover bolts. • Remove the muffler cover with the plastic mallet.
• Remove the muffler mounting bolt.
j
A. Plastic Mallet
A. Muffler Cover Bolts B. Muffler Cover
B. Muffler Mounting Bolt

• Replace the silencer wool with a new one. • Check that the exhaust port of the muffler body
• fler cover andsilicone
Remove the sealant attaching on the muf-
muffler body.
cover align with the muffler pipe.
j
• Arrange the shape of the silencer wool and install
the muffler cover to the muffler body.
A. Muffler Pipe End

B. Baffle
A. Silencer Wool
B. Muffler Body
C. Muffler Cover

• Apply a non-permanent locking agent to the muf- • Secondly, tighten the muffler mounting bolt (rear).
fler cover bolts. • Thirdly, tighten the muffler clamp bolt.
• Tighten the muffler cover bolts and apply the sili-
cone sealant to the joint part of the muffler cover
j
and muffler body.
A. Muffler Clamp Bolt

B. Muffler Mounting Bolt
C. Muffler Body
A. Muffler Cover
B. Muffler Body Tightening Torque
C. Muffler Cover Bolts Muffler Mounting Bolts:
D. Silicone Sealant 21 N·m (2.1 kgf·m, 15 ft·lb)
Muffler Clamp Bolt:
NOTE 11 N·m (1.1 kgf·m, 97 in·lb)
If the threaded holes of the muffler cover and muf-
fler body do not align, remove the muffler clamp
bolt and muffler mounting bolts.
• Firstly, tighten the muffler mounting bolt (front).

• Insert the tabs of the side cover into the slots of

the air cleaner housing, and tighten the bolts. Drive Chain
j For safety and to prevent excessive wear, the drive
chain must be checked, adjusted, and lubricated be-
fore riding. If the chain becomes badly worn or mal-
adjusted - either too loose or too tight - it could jump
off the sprockets or break.
WARNING
A chain that breaks or jumps off the sprock-
ets could snag on the engine sprocket or lock
the rear wheel, severely damaging the motor-
cycle and causing it to go out of control. In-
spect the chain for damage and proper ad-
justment before each ride.
A. Tabs
B. Slots
Chain Slack Inspection
• Raise the rear wheel off the ground, then rotate
the rear wheel to find the place where the chain is
tightest (because it wears unevenly).
• Push up the drive chain in the middle of the upper
chain run to measure the chain slack. The dis-
tance between the center-line of the chain and the
swingarm (at the end of the chain slipper) should
be within the standard value.
Drive Chain Slack
Standard 52 a 58 mm (2.0 a 2.3 in.)

• Adjust
cation.
the drive chain if its slack is out of specifi- For the rear wheel to be properly aligned, the
notch of the left chain adjuster should align with
the same swingarm mark that the notch of the
right chain adjuster aligns with.
j
Drive Chain Slack
52 a 58 mm (2.0 a 2.3 in.)
A. Chain Slack
• Inwheel
addition to checking the slack, rotate the rear
to inspect the drive chain for damaged
rollers, loose pins and links and the sprockets
for unevenly or excessively worn and damaged
teeth. A. Rear Axle Nut
• If there are any such defects, replace the drive
chain and/or the sprockets.
B. Adjusting Bolt
C. Locknut
D. Marks
Chain Slack Adjustment E. Notch
• Remove the cotter pin from the rear axle nut. F. Cotter Pin
• locknuts. rear axle nut and both chain adjuster
Loosen the
NOTE
• Turn both chain adjusting bolts evenly until the
drive chain slack (measured between the chain
Wheel alignment can also be checked using the
straightedge or string method.
and the swingarm) is within the standard value.

WARNING
Misalignment of the wheel will result in ab-
j normal wear, and may result in an unsafe
riding condition. Align the rear wheel using
the marks on the swingarm or measuring the
distance between the center of the axle and
swingarm pivot.
• Tighten both chain adjuster locknuts.

• Tighten the axle nut to the specified torque.
Tightening Torque
Rear Axle Nut:
108 N·m (11.0 kgf·m, 80 ft·lb)
A. Cotter Pin
• Rotate the wheel, measure the chain slack again
at the tightest position, and readjust it if necessary. NOTE
• Install a new cotter pin through the axle nut and
axle, and bend its ends.
When inserting the cotter pin, if the slots in the nut
do not align with the cotter pin hole in the axle,
tighten the nut clockwise up to the next alignment.
It should be within 30°.
Loosen once and tighten again when the slot goes
past the nearest hole.

overly tight chain, which can cause it to break.

To prevent this, adjust the chain slack (measured
between the chain and the swingarm) to 62 a 68
mm (2.4 a 2.7 in.).
j
Chain Wear Inspection

When the chain has reached its wear limit (i.e.,
when it has stretched by 1.7% of its original length),
it is no longer safe for use and should be replaced.
Since it is impractical to measure the entire length of
the chain, determine the degree of wear by measur-
ing a 20-link section of the chain.
• Tighten the chain either by using the chain ad-
justers or by hanging a 10 kg (22 lb) weight on the
A. Turning Clockwise chain.
• Measure the 20-link length on a straight part of the
chain from the center of the 1st pin to the center
WARNING of the 21st pin. If the length exceeds the service
A loose axle nut can lead to an accident re- limit, the chain should be replaced. Since over-
sulting in serious injury or death. Tighten worn sprockets will cause a new chain to wear
the axle nut to the proper torque and install faster, inspect both the engine and rear sprockets
a new cotter pin. whenever the chain is replaced, and replace them
if necessary.
• Check the rear brake effectiveness.
NOTE
When riding in wet and muddy conditions, mud
sticks to the chain and sprockets, resulting in an

To minimize any chance of the master link coming

apart, the master link clip must be installed with
the closed end of the “U” pointing in the direction
j of chain rotation.
A. Weight
B. Tape Measure
Drive Chain 20-Link Length

317.5 a 318.2 mm (12.50 a 12.53
Standard A. Master Link Clip
in.)
B. Direction of Chain Rotation
Service Limit 323 mm (12.7 in.)
NOTE
The drive system was designed for use with a
DAIDO DID 520DMA4 114-links chain. For maxi-
mum stretch resistance and safety, a genuine part
must be used for replacement.

Chain Guide Wear Inspection Chain Slipper Wear Inspection

• Visually inspect the drive chain guide and replace
it if excessively worn or damaged.
• Visually inspect the upper and lower of the chain
slipper on the swingarm and replace them if worn
or damaged.
j
A. Chain Guide
A. Upper and Lower of the Chain Slipper
B. Swingarm

Sprocket Wear Inspection Chain Lubrication
•Visually inspect the sprocket teeth and replace the
sprocket if its teeth are worn or damaged.
Lubrication of the drive chain is necessary after rid-
ing in the rain or mud, or any time the chain appears
j Sprocket Teeth Wear dry. A heavy oil such as SAE90 is preferred to a
lighter oil because it will stay on the chain longer and
provide better lubrication.
• Apply oil to the side of the rollers so that it will
penetrate to the rollers and bushings.
• Wipe off any excess oil.
A. Good Teeth
B. Worn Teeth
C. Damaged Teeth
NOTE
Sprocket wear is exaggerated in the illustration.

Handlebar
To suit various riding positions, the handlebar
j
can be adjusted by turning the handlebar holders
around.
• Remove the handlebar pad.
• Check the handlebar for bent or crack.
• Remove the handlebar clamp bolts, the clamps
and the handlebar.
A. Handlebar Holders
B. Handlebar Holder Nuts
• Put the handlebar on the handlebar holders.

• Check the
Mount handlebar clamps.
• the left and the
that gauge on the handlebar is out of
right handlebar clamps equally.
• Tighten the front and rear bolts of the handlebar
clamps equally. If the handlebar clamps are cor-
rectly installed, there will be even gap on the front
and rear side of the clamp after the bolts torqued.
A. Handlebar Clamps
B. Clamp Bolts Tightening Torque
C. Handlebar Handlebar Clamp Bolts:
25 N·m (2.5 kgf·m, 18 ft·lb)
• Remove the handlebar holder nuts, and turn the
handlebar holders 180°.
• Replace the handlebar holder nuts with new ones. NOTE
• Tighten the new handlebar holder nuts securely. Tighten the two clamp bolts alternately two times
to ensure even tightening torque.

Brakes
j Disc and disc pad wear is automatically compen-
sated for and has no effect on the brake lever or
pedal action. There are no parts on the brakes that
require adjustment except brake lever position.
Brake Lever Position
The brake lever position can be adjusted to suit
the rider’s preference.
• To adjust the brake lever position, slide the front
brake lever dust cover back, and loosen the lock-
nut, and turn the adjuster to either side with a
wrench.
A. Handlebar Clamps
B. Clamp Bolts • After adjustment, tighten the locknut securely.
C. Gap
D. Supporting Bar
• Do not disassemble the supporting bar on the han-

dlebar.
• Check the front brake for the proper brake effect,
or no brake drag.
A. Brake Lever
B. Adjuster
C. Locknut

• Test the braking power and check that there is no

brake drag.
NOTICE
Do not spill brake fluid onto any painted sur-
WARNING face. j
Do not use fluid from a container that has
Air in the brake lines diminish braking perfor- been left open or that has been unsealed for
mance and can cause an accident resulting a long time.
in injury or death. If the brake lever or pedal Check for fluid leakage around the brake sys-
feels mushy when it is applied, there might tem fittings.
be air in the brake lines or the brake may be Check for brake hose damage.
defective. Have the brake checked immedi-
ately by an authorized Kawasaki dealer.
Brake Fluid Level Inspection (Front and Rear
Brake Reservoirs)
Disc Brake Fluid With the front or rear brake reservoir positioned
Inspect the brake fluid level in the front and rear horizontally, the brake fluid must always be above
brake reservoirs and change the brake fluid in ac- the lower level line.
cordance with the Periodic Maintenance Chart. The
brake fluid should also be changed when contami-
nated with dirt or water.
Use only heavy-duty brake fluid as follows.
Front/Rear Brake Fluid : DOT3 or DOT4
NOTE
The motorcycle is shipped with brake fluid DOT4
in the brake system.
A. Front Brake Reservoir

B. Lower Level Line

A. Rear Brake Reservoir A. Front Brake Reservoir

B. Lower Level Line B. Upper Level Line
• Ifis the brake fluid in the front or rear brake reservoir

below the lower level line, check for fluid leaks
in the brake line and fill the reservoir to the upper
level line (The step inside the front and rear brake
reservoirs indicate the upper level.).
A. Rear Brake Reservoir

B. Upper Level Line

WARNING Brake Pad Wear Inspection

Inspect the brake pads for wear in accordance with
Mixing brands and types of brake fluid can
the Periodic Maintenance Chart. If the thickness of
reduce the brake system’s effectiveness
any pad in any (front or rear) brake caliper is less
j
and cause an accident resulting in injury
than 1 mm (0.04 in.), have both pads in the caliper
or death. Do not mix two brands of brake
replaced as a set. Pad replacement should be done
fluid. Change the brake fluid in the brake line
by an authorized Kawasaki dealer.
completely if the brake fluid must be refilled
Usable Brake Pad Range
but the type and brand of the brake fluid that
is already in the reservoir are unidentified.
A. Lining Thickness
B. 1 mm (0.04 in.)

the figure. If play is felt, the steering is too loose
Steering and needs to be adjusted.
j The steering should always be kept adjusted so
that the handlebar will turn freely but not have ex-
cessive play.
Steering Inspection
• To check the steering adjustment, raise the front
wheel off the ground using a jack (special tool:
57001-1238) and attachment (special tool: 57001
-1252 or 1608).
• Push the handlebar lightly to either side. If the
handlebar continues moving under its own mo-
mentum, the steering is not too tight.
• Squatting in front of the motorcycle, grasp the
lower ends of the front fork at the axle, and push
and rock the front fork back and forth as shown in A. Push and Rock

Steering Adjustment • Remove the handlebar (see Handlebar section).

• Raise the front wheel off the ground using a jack
(special tool: 57001-1238) and attachment (spe-
• per).
Loosen the left and right front fork clamp bolts (up-
j
cial tool: 57001-1252 or 1608). • Remove the steering stem head nut, and raise the
• Unlock the clamp of the number plate. steering stem head.
• Remove the bolt.
• Clear the holes and remove the number plate.
A. Steering Stem Head

B. Steering Stem Head Nut
A. Clamp C. Front Fork Clamp Bolts (Upper)
B. Bolt
C. Holes
D. Number Plate

• Turn the steering stem locknut with a stem nut

wrench (special tool: 57001-1100) to obtain the
Tightening Torque
Steering Stem Head Nut:
proper adjustment. 98 N·m (10.0 kgf·m, 72 ft·lb)
j
Front Fork Clamp Bolts (Upper):
23 N·m (2.3 kgf·m, 17 ft·lb)
NOTE
Tighten the two clamp bolts alternately two times
• Install the handlebar (see Handlebar section), and

check the steering again and readjust it if neces-
sary.
• Check the front brake for the proper brake effect,
or no brake drag.
A. Steering Stem Locknut
B. Stem Nut Wrench (Special Tool: 57001-1100)
• Install
tion.
the steering stem head to the original posi-
• Apply a non-permanent locking agent to the front

fork clamp bolts (upper).
• Apply the specified torques to the steering stem
head nut and front fork clamp bolts (upper).

NOTICE
Front Suspension If the inner tube is badly bent or creased,
replace it. Excessive bending, followed by j
Front Fork Inspection subsequent straitening, can weaken the in-
• Holding the brake lever, pump the front fork back
and forth manually to check for smooth operation.
ner tube.
• Visually inspect the front fork for oil leakage, scor-

ing or scratches on the outer surface of the inner
Front Fork Adjustment
Any of the following front fork adjustments should
tube. be made to tune the front suspension to the rider’s
• If necessary, repair or replace by an authorized
Kawasaki dealer.
weight and the condition of the track.
Basically, there are seven adjustments you can
make to the front fork.
• Air Pressure
Air pressure acts as a progressive spring over the
entire fork travel range. Since the air pressure in the
fork legs increases with normal use, the fork action
on your KX will get stiffer as the race progresses.
Therefore, it is not recommended to increase the air
pressure for additional springing. The KX forks are
designed to function without added air.
• Rebound Damping Adjustment (Left Fork only)
This adjustment affects how quickly the fork re-
bounds. Depending on the model, the fork rebound
damping adjuster has at least 20 positions. The fully
seated position (adjuster turned fully clockwise) is
A. Inner Tubes the hardest setting. Turning the adjuster 10 clicks
counterclockwise from the fully seated position is the
standard setting, turning it counterclockwise 20 or
more clicks (depending on the model) is the softest
setting.
• Compression Damping Adjustment (Left Fork
only)

This adjustment affects how quickly the fork com- due to weight biasing. Increasing the amount of fork
presses. Depending on the model, the fork com- tube protrusion has opposite effects. Be sure that
pression damping adjuster has at least 22 positions. the front tire does not touch the fender when the fork
j The fully seated position (adjuster turned fully clock- is fully compressed. Make this adjustment in 10 mm
wise) is the hardest setting. Turning the adjuster 7 (0.39 in.) steps.
clicks counterclockwise from the fully seated posi-
tion is the standard setting, turning it counterclock- NOTICE
wise 22 or more clicks (depending on the model) is The right and left fork tubes must be adjusted
the softest setting. evenly.
• Spring Preload Adjustment (Right Fork only)
This adjustment affects the driving position. De-
pending on the model, the fork spring preload ad- Air Pressure Adjustment
juster has at least 60 positions. The fully seated po- The standard air pressure in the front fork legs is
sition (adjuster turned fully counterclockwise) is the atmospheric (0 kPa, 0 kgf/cm², 0 psi). Air pressure
softest setting. Turning the adjuster 22 clicks clock- in the fork legs increase with normal use, so the fork
wise from the fully seated position is the standard action stiffens during operation. Release air pres-
setting, turning it clockwise 60 or more clicks (de- sure from the fork legs prior to each race through the
pending on the model) is the hardest setting. pressure relief screw located in each front fork top
• Fork Oil Amount Adjustment
The fork oil amount affects only the final 100 mm
plug. Make sure the front forks are fully extended
with the front wheel off the ground when releasing
(4 in.) of fork travel. A higher oil amount will make the pressure.
the fork rebound more quickly. A lower oil amount
will make the fork rebound more slowly.
• Raise the front wheel off the ground using a jack
• Fork Springs
Optional springs, softer and stiffer than standard, •
cial tool: 57001-1252 or 1608).
Remove the screw on each front fork top plug to
are available. let the air pressure equalize. Then, tighten the
• Fork Clamp Position
Steering is greatly affected by the fork clamp posi-
screws.
Tightening Torque
tion (how much the outer fork tubes protrude above
Pressure Relief Screws:
the steering stem head). The less the fork tube pro-
1.3 N·m (0.13 kgf·m, 12 in·lb)
trudes, the lighter the front end becomes and the
greater the tendency for understeering and washout

A. Screw A. Screw
B. Front Fork Top Plug B. Front Fork Top Plug
C. Front Fork (Left Side) C. Front Fork (Right Side)
Rebound Damping Adjustment (Left Fork only)

• Clean the bottom of the left fork tube.
• on the leftthe
To adjust rebound damping, turn the adjuster
front fork cylinder valve with a flat-head
screwdriver. Adjust the rebound damping to suit
your preference under certain conditions.
NOTICE
Do not force the rebound damping adjuster
beyond the fully seated position, or the ad-
justing mechanism may be damaged.

Rebound Damping Adjuster Settings
A. Rebound Damping Adjuster

B. Left Front Fork Cylinder Valve
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range
20 clicks or more.
Standard Rebound Damping Adjuster Setting
10 clicks*
*: Counterclockwise from the fully seated position

Compression Damping Adjustment (Left Fork
only)
• To adjust the compression damping, turn the ad-
juster on the left front fork base valve assembly

with a flat-head screwdriver. Adjust the compres- Compression Damping Adjuster Settings
sion damping to suit your preference under certain
conditions.
j
NOTICE
Do not force the compression damping ad-
juster beyond the fully seated position, or the
adjusting mechanism may be damaged.

Clockwise)
D. Standard Setting
22 clicks or more.
Standard Compression Damping Adjuster
A. Compression Damping Adjuster
B. Left Front Fork Base Valve Assembly
Setting
8 clicks*

Spring Preload Adjustment (Right Fork only)
• To adjust the spring preload, turn the adjuster on
the right front fork top plug with a wrench. Adjust

the spring preload to suit your preference under Spring Preload Adjuster Settings
certain conditions.
j NOTICE
Do not force the spring preload adjuster be-
yond the fully seated position, or the adjust-
ing mechanism may be damaged.

Counterclockwise)
B. Harder (Clockwise)
C. Softer (Counterclockwise)
D. Standard Setting
*: Number of turns clockwise usable range 60
clicks or more.
A. Spring Preload Adjuster
B. Right Front Fork Top Plug
Standard Spring Preload Adjuster Setting
16 clicks*
*: Clockwise from the fully seated position

Front Fork Oil Change
• Thoroughly clean the forks before disassembly.

NOTICE
Be careful not to scratch the inner tube and
not to damage the dust seal. j
Avoid scratching or damaging the inner tube
or the dust seal. Use a mild detergent and
sponge out dirt with plenty of water.
NOTE
Set the rebound and compression damping and
spring preload setting to the softest settings before
disassembly to prevent the needle of adjusters
from damping. Record the setting before turning
the adjuster.
A. Front Fork Clamp Bolts (Upper)
• Remove the number plate (see Steering section). B. Top Plug Wrench (Special Tool: 57001-1645)
• Loosen the front
Loosen the fork clamp bolts (upper).
• Support the motorcycle using a jack (special tool:
• wrench (special tool:
front fork top plug with the top plug
57001-1645). 57001-1238) and attachment (special tool: 57001
-1252 or 1608).
NOTE
Do not take off the base valve assembly (left fork
• Unscrew the front axle nut, and then loosen the
left front axle clamp bolts.
only). • Remove the brake caliper from the fork leg to be
removed, and rest the caliper on some kind of
stand so that it does not dangle.
• Insert the wood wedge between the disc brake
pads. This prevents them from being moved out of
their proper position, if the brake lever is squeezed
accidentally.
• Remove the brake hose clamps and fork protector.

NOTICE
Do not lay the wheel on the ground with the
j disc facing down. This can damage or warp
the disc. Place blocks under the wheel so the
disc does not touch the ground.
A. Front Axle Nut

B. Left Front Axle Clamp Bolts (Loosen)
C. Bolts
D. Front Brake Caliper
E. Front Fork Protector
F. Brake Hose Clamps
• Loosen the right front axle clamp bolts.

• the front suitable
Place a stand under the engine to raise
wheel off the ground.
A. Right Front Axle Clamp Bolts (Loosen)
B. Front Axle
C. Collar
• Remove the front axle, and pull out the front wheel.
Take off the collar from each side of the front hub.

• Loosen the front fork clamp bolts (lower). Standard

317 a 321 mm (12.48 a 12.64 in.)
• twisting it.the front fork tubes by pulling down while
Remove Length
j
A. Front Fork Clamp Bolts (Lower) A. Length

B. Pull down by twisting. B. Axle Holder
C. Front Fork Tube C. Front Fork Outer Tube
• Measure each length between the axle holder and

outer tube and record it before disassembling the
fork.

Left Front Fork • Place a drain pan under the front fork and drain
• Using the top plug wrench (special tool: 57001
-1645), remove the left front fork cylinder unit from
fork oil.
j the outer tube and slowly slide down the outer
NOTE
tube. Pump the outer tube several times to discharge
the fork oil.
A. Top Plug Wrench (Special Tool: 57001-1645)

B. Left Front Fork Cylinder Unit A. Fork Oil
C. Left Front Fork Outer Tube

• Temporarily install the left front fork cylinder unit to

the outer tube using the top plug wrench (special
• Loosen the adjuster assembly completely.
tool: 57001-1645).
NOTE
When removing the adjuster assembly, do not j
force to loosen it at once using an impact wrench.
A. Left Front Fork Cylinder Unit

B. Left Front Fork Outer Tube
C. Top Plug Wrench (Special Tool: 57001-1645)
A. Axle Holder Part
• Hold the axle holder with a vise. B. Left Front Fork Adjuster Assembly
WARNING • Hold the locknut with a wrench and remove the left
front fork adjuster assembly.
Clamping the axle holder too tight can dam-
age it which will affect riding stability. NOTE
Do not clamp the axle holder too tight. Do not remove the locknut from the piston rod.
The piston rod may slide into the inner tube.
NOTE
Protect the axle holder with a soft jaw or heavy
cloth when using a vise.

• Remove the push rod.

j
A. Locknut
B. Wrench
C. Left Front Fork Adjuster Assembly A. Push Rod
NOTICE
Removing the locknut and pushing the pis-
ton rod thread into the left front fork cylinder
unit will damage the oil seal. Do not remove
the locknut from the piston rod.

• Remove the fork leg from the vise. • Remove the left front fork cylinder unit from the
• plug wrenchleft(special
Loosen the front fork cylinder unit with the top
tool: 57001-1645).
outer tube.
j

A. Left Front Fork Cylinder Unit B. Piston Rod

• Holding the top plug wrench (special tool: 57001

-1645) with a vise, loosen the left front fork base
valve assembly on the fork cylinder unit with a
j hexagon box wrench.
A. Left Front Fork Base Valve Assembly

B. Left Front Fork Cylinder Unit
NOTE
A. Top Plug Wrench (Special Tool: 57001-1645) Slowly compress the piston rod until it stops so
B. Left Front Fork Base Valve Assembly that the left front fork base valve assembly can be
C. Left Front Fork Cylinder Unit removed easily.
D. Hexagon Box Wrench
• Remove the left front fork base valve assembly NOTICE

from the fork cylinder unit. Disassembling the left front fork base valve
assembly can lead to trouble. Do not disas-
NOTICE semble the left front fork base valve assem-
Be careful not to damage the bushing of the bly.
left front fork base valve assembly.

• Drain the fork oil from the left front fork cylinder
unit by pumping the piston rod several times.
• Clean the threads of the left front fork cylinder unit
and left front fork base valve assembly.
• Hold the front fork at the inverted position for more
than 20 minutes to allow the fork oil to fully drain.
j
A. Threads

• With the piston rod fully stretched, pour 260 mL

(8.79 US oz.) of fork oil.
• Pump
air.
the piston rod slowly several times to expel
A. Fork Oil A. Pump

B. Left Front Fork Cylinder Unit B. Piston Rod
Recommended Fork Oil • With the piston rod fully stretched, check the oil
level in the left front fork cylinder unit.
SHOWA SS19 or equivalent
Oil Level
115 a 123 mm (4.53 a 4.84 in.)
NOTE
Measure the oil level using a gauge as shown in
the figure.

A. 115 a 123 mm (4.53 a 4.84 in.) A. O-rings

B. Oil Level B. Bushings
• Replace the O-rings on the left front fork base

valve assembly with new ones.
• With the piston rod held immovable fully stretched,
gently install the left front fork base valve assem-
• Apply specified fork oil to the O-rings and bushings
on the left front fork base valve assembly.
bly to the left front fork cylinder unit.
NOTE
NOTICE If there is difficulty in assembling the base valve,
it may be because the oil level is too high. Check
Do not damage the bushings when assem- the oil level in the left front fork cylinder unit.
bling the left front fork base valve.
• Hold the top plug wrench (special tool: 57001
-1645) with a vise.
• Holding the left front fork cylinder unit with the top
plug wrench (special tool: 57001-1645), torque
the left front fork base valve assembly.

• Discharge the extra oil off the left front fork cylinder
unit by pumping the piston rod to full stroke.
j NOTICE
Be careful not to bend or damage the pis-
ton rod when the piston rod is stroked. Ser-
vice carefully because oil flies out from the
oil hole of the left front fork cylinder unit.

B. Left Front Fork Base Valve Assembly
C. Left Front Fork Cylinder Unit
Tightening Torque
Left Front Fork Base Valve Assembly:
30 N·m (3.1 kgf·m, 22 ft·lb)
NOTE
Check if the locknut is completely screwed onto A. Piston Rod
the piston rod. B. Heavy Cloth
C. Pump the piston.
• Protect the piston rod end with a heavy cloth to
prevent piston rod thread damage. NOTE
• Hold the left front fork cylinder unit at the upright
position and slowly pump the piston rod several Set the compression damping force setting to the
softest. Check the piston rod sliding surface for
times about 100 mm (3.94 in.).
damage. Apply fork oil to the piston rod sliding
surface.

• Drain the extra oil from the left front fork cylinder
unit oil hole.
• Protect the piston rod end with a heavy cloth to
prevent damage.
• Blow out the extra oil from the oil hole of the left
front fork cylinder unit with the compressed air
• Pump the piston rod to full stroke by pushing down
the left front fork cylinder unit.
j
blow to the oil hole. • Check the piston rod for smooth operation.
• Wipe
unit.
the oil off completely from the fork cylinder • Ifpiston
the piston rod operation is not smooth, check the
rod for bend or damage.
• Ifpressure
you cannot use compressed air, remove the
relief screw of the left front fork base
• piston rodfork
Hold the cylinder unit on level ground while
is full stroked by your hand.
valve assembly. Up side down the fork damper
for 10 minutes and drain the oil from the left front
• Release the piston rod then check the piston rod
extend to maximum.
fork cylinder unit. Reinstall and tighten the pres-
sure relief screw.
• Ifbleed
the piston rod does not extend to maximum,
the left front fork cylinder unit again.
Tightening Torque
NOTICE
Pressure Relief Screw:
1.3 N·m (0.13 kgf·m, 12 in·lb) Be careful not to bend or damage the piston
rod when the piston rod is stroked.
A. Oil Hole

• Wipe the oil off completely from the left front fork
cylinder unit.
• Iffront
oil leaks from the cylinder unit, replace the left
fork cylinder unit assembly.
j • aCompress the piston rod to 200 a 250 mm (7.87
9.84 in.) and hold the left front fork cylinder unit
• and release
Hold the left front fork cylinder unit on level ground
the piston rod then check the piston
upright position for 10 minutes. rod extend to maximum.
• (0.39
Tighten the locknut fully and measure 10 a 12 mm
a 0.47 in.) as shown in the figure.

B. Piston Rod
C. 200 a 250 mm (7.87 a 9.84 in.) A. Locknut
B. 10 a 12 mm (0.39 a 0.47 in.)
• There should be no oil leak from the left front fork
cylinder unit.

• Completely wipe off the fork oil from the left front
fork cylinder unit.
• Temporarily tighten the left front fork cylinder unit
using the top plug wrench (special tool: 57001
• Insert above-mentioned parts into the fork. -1645).
j
A. Left Front Fork Cylinder Unit A. Left Front Fork Cylinder Unit
• Hold the axle holder with a vise.

NOTE
Protect the axle holder with a soft jaw or heavy
cloth when using a vise.
WARNING
Clamping the axle holder too tight can dam-
age it which will affect riding stability.
Do not clamp the axle holder too tight.

• Replace the O-ring on the left front fork adjuster

assembly with a new one and apply specified fork
• Slowly turn the left front fork adjuster assembly
clockwise until resistance is felt and check the
oil to the O-ring. clearance between the locknut and left front fork
j
• Insert the push rod into the piston rod. adjuster assembly for more than 1 mm (0.04 in.).
• Install the left front fork adjuster assembly to the
push rod.
A. Left Front Fork Adjuster Assembly

B. Locknut
A. Push Rod C. More Than 1 mm (0.04 in.)
B. Left Front Fork Adjuster Assembly
• Turn the locknut counterclockwise until it contacts
with the left front fork adjuster assembly.
• With the locknut held immovable using a wrench,
tighten the left front fork adjuster assembly locknut
to the specified torque.
Tightening Torque
Left Front Fork Adjuster Assembly Locknut:
22 N·m (2.2 kgf·m, 16 ft·lb)

A. Locknut A. Axle Holder Part

B. Wrench B. Left Front Fork Adjuster Assembly
C. Left Front Fork Adjuster Assembly
• Compare the length at assembly and at disassem-
• Apply a non-permanent locking agent and tighten bly. There should be same length.
the left front fork adjuster assembly to the speci-
fied torque.
• Ifsembly,
the length at assembly is longer than at disas-
check the left front fork adjuster assembly
Tightening Torque and locknut installation.
Left Front Fork Adjuster Assembly: Standard
317 a 321 mm (12.48 a 12.64 in.)
69 N·m (7.0 kgf·m, 51 ft·lb) Length

-1645), remove the left front fork cylinder unit from
the outer tube and slowly slide down the outer
tube.

A. Top Plug Wrench (Special Tool: 57001-1645) A. Left Front Fork Outer Tube
B. Left Front Fork Cylinder Unit B. Fork Oil
C. Left Front Fork Outer Tube
Recommended Fork Oil
• Pour the specified amount of fork oil into the left
front fork outer tube. SHOWA SS19 or equivalent
Standard Left Fork Oil Capacity

Left Fork Oil
374 mL (12.6 US oz.)
Capacity
342 a 381 mL (11.6 a 12.9 US
Adjustable Range
oz.)
• Raise the left front fork outer tube and temporarily

install the left front fork cylinder unit to the outer
tube using the top plug wrench (special tool:
57001-1645).

Right Front Fork

• Check the position of the right front fork spring
preload adjuster so that it can be installed in the
original position.
j

A. Right Front Fork Spring Preload Adjuster


-1645), remove the top plug from the right front
• Install the clamps (special tool: 57001-1693) as
shown in the figure, and tighten the bolts.
j fork outer tube and slowly slide down the outer
tube.
• Screw the holders of the fork spring compressor
(special tool: 57001-1587).
A. Top Plug Wrench (Special Tool: 57001-1645) A. Clamps (Special Tool: 57001-1693)
B. Top Plug B. Bolts
C. Right Front Fork Outer Tube C. Holders

• Set the right front fork tube on the base (special

tool: 57001-1753) as shown in the figure.
• Insert the compression shaft and screw the exten-
sion rod (special tool: 57001-1753).
• Set the other side compression shaft same
process.
j
A. Base (Special Tool: 57001-1753)
A. Compression Shaft
B. Extension Rod (Special Tool: 57001-1753)

• Screw the extension rods (special tool: 57001 • Install the nuts.
-1753) into the base (special tool: 57001-1753). • out. in the nuts until the piston rod nut comes
Screw
j
A. Extension Rod (Special Tool: 57001-1753)

B. Base (Special Tool: 57001-1753) A. Nuts

• Holding the piston rod nut with a spanner, loosen

the right front fork spring preload adjuster.
• Remove
base.
the fork spring compressor, clamp and
• Remove the spring collar. j
A. Piston Rod Nut

B. Spanner A. Spring Collar
C. Right Front Fork Spring Preload Adjuster

• Unscrew the piston rod nut. • Place a drain pan under the right front fork and
• Remove the spring guide and fork spring. drain fork oil.
j NOTE
Pump the right front fork outer tube and piston rod
several times to discharge the fork oil.
A. Piston Rod Nut

B. Spring Guide
C. Fork Spring
A. Fork Oil
B. Piston Rod
C. Right Front Fork Outer Tube

• Hold the right front fork at the inverted position for

more than 30 minutes to allow the fork oil to fully
• Install
upward.
the fork spring with the smaller end facing
drain.
j
A. Fork Spring
B. Smaller End

• Using the fork piston rod puller (special tool: • Install the spring guide.
57001-1298), pull up the piston rod. • down. the piston rod nut with the unthread side
Install
j
A. Fork Piston Rod Puller, M10 × 1.0 (Special Tool:

57001-1298) A. Piston Rod Nut
B. Piston Rod B. Piston Rod

• Screw the piston rod nut onto the piston rod as

shown in the figure.
• Install the spring collar.
j
A. Spring Collar
A. Piston Rod Nut
B. Piston Rod
C. 13 mm (0.51 in.) or more

• Install the clamps (special tool: 57001-1693) as

shown in the figure, and tighten the bolts.
• Set the right front fork tube on the base (special
tool: 57001-1753) as shown in the figure.
j • Screw the holders of the fork spring compressor
(special tool: 57001-1587).
A. Base (Special Tool: 57001-1753)
A. Clamps (Special Tool: 57001-1693)

B. Bolts
C. Holders

• Insert the compression shaft and screw the exten-

sion rod (special tool: 57001-1753).
• Screw the extension rod (special tool: 57001
-1753) into the base (special tool: 57001-1753).
• Set the other side compression shaft same
process.
j
A. Extension Rod (Special Tool: 57001-1753)

B. Base (Special Tool: 57001-1753)
A. Compression Shaft
B. Extension Rod (Special Tool: 57001-1753)

• Install the nuts.

• out. in the nuts until the piston rod nut comes
Screw
j
A. Top Plug
B. Piston Rod Nut
C. Clearance (0.5 mm (0.02 in.) or more)
A. Nuts • Turn the piston rod nut counterclockwise until it
contacts the top plug.
• Turn the top plug clockwise.
• Holding the right front fork spring preload adjuster
• Check the clearance (0.5 mm (0.02 in.) or more)
between the lower end of the top plug and upper
with a wrench, tighten the piston rod nut to the
specified torque.
end of the piston rod nut.
Tightening Torque
NOTE
Right Front Fork Piston Rod Nut:
If the clearance is less than 0.5 mm (0.02 in.), the 20 N·m (2.0 kgf·m, 15 ft·lb)
piston rod nut may be installed upside down.

• Push the top plug into the spring collar to make

sure that it is securely installed.
j
A. Piston Rod Nut

B. Top Plug
C. Spanner
D. Right Front Fork Spring Preload Adjuster A. Top Plug
B. Spring Collar

• Remove
base.
the fork spring compressor, clamp and Standard Right Fork Oil Capacity
Right Fork Spring 9.5 N/mm (0.97 kgf/mm)
j • Pour the specified amount of fork oil into the right
front fork outer tube. Right Fork Oil
205 mL (6.93 US oz.)
Capacity
• Replace the O-ring on the top plug with a new one
and apply specified fork oil to the O-ring. 130 a 492 mL (4.4 a 16.6 US
Adjustable Range
oz.)
• When changing the fork spring, the oil capacity is

as shown in the table.
Standard Oil 205 mL (6.93 US
SOFT Capacity oz.)
(K = 9.1
N/mm) Adjustable 130 a 500 mL (4.4 a
Range 16.9 US oz.)
Standard Oil 205 mL (6.93 US
HARD Capacity oz.)
(K = 9.9
N/mm) Adjustable 130 a 482 mL (4.4 a
Range 16.3 US oz.)
A. Right Front Fork Outer Tube

B. Fork Oil
• Raise the right front fork outer tube and temporar-
ily install the top plug to the outer tube using the
C. O-ring top plug wrench (special tool: 57001-1645).
Recommended Fork Oil
SHOWA SS19 or equivalent

A. Top Plug A. Left Front Fork Cylinder Unit

B. Right Front Fork Outer Tube B. Top Plug Wrench (Special Tool: 57001-1645)
C. Top Plug Wrench (Special Tool: 57001-1645) C. Torque Wrench
• Install the front fork tubes to the motorcycle. Tightening Torque

• specifiedthetorque.
Tighten front fork clamp bolts (lower) to the
Left Front Fork Cylinder Unit:
34 N·m (3.5 kgf·m, 25 ft·lb)
Tightening Torque Right Front Fork Top Plug:
Front Fork Clamp Bolts (Lower): 34 N·m (3.5 kgf·m, 25 ft·lb)
23 N·m (2.3 kgf·m, 17 ft·lb)
NOTE
• Tighten the left front fork cylinder unit and right
front fork top plug using the top plug wrench (spe- The torque of left front fork cylinder unit and right
cial tool: 57001-1645) to the specified torque. front fork top plug are specified to 34 N·m (3.5
kgf·m, 25 ft·lb) however, when you use the top
plug wrench (special tool: 57001-1645), reduce
the torque to 90% of the specified value (31 N·m
(3.1 kgf·m, 23 ft·lb)) due to the distance between
the center of the square hole, where the torque

wrench is fitted, and that of the octagonal hole of
the wrench.
• Install the front brake caliper to the fork leg, and
tighten the front caliper mounting bolts to the spec-
j This torque value (31 N·m (3.1 kgf·m, 23 ft·lb)) is ified torque.
applicable when you use a torque wrench whose Tightening Torque
length gives leverage of approximately 310 mm
(12.2 in.) between the grip point to the center of Front Caliper Mounting Bolts:
the coupling square. 25 N·m (2.5 kgf·m, 18 ft·lb)
• Apply a non-permanent locking agent to the front

fork clamp bolts (upper).
• Take
pads.
out wood wedge between the disc brake
• Tighten the front fork clamp bolts (upper) to the

specified torque.
• Apply high-temperature grease to the oil seals of
the wheel.
Tightening Torque • Install
hub.
the collars on the left and right side of the
Front Fork Clamp Bolts (Upper):
23 N·m (2.3 kgf·m, 17 ft·lb) • Put the front wheel assembly between the fork
legs, and insert the front brake disc into the front
brake pads.
• Insert the front axle from the right side of the mo-
torcycle.
• Tighten the right front axle clamp bolts temporary.
• Tighten the front axle nut to the specified torque.
Tightening Torque
Front Axle Nut:
78 N·m (8.0 kgf·m, 58 ft·lb)
• Tighten the left front axle clamp bolts to the spec-

ified torque.
Tightening Torque
Left Front Axle Clamp Bolts:
20 N·m (2.0 kgf·m, 15 ft·lb)
B. Distance

NOTE NOTE
Tighten the two clamp bolts alternately two times Do not apply the front brake during this process
to ensure even tightening torque. to stop the motorcycle from rolling forward. Put a j
block in front of the wheel to stop it from moving.
A. Collars
B. Front Axle A. Pump the forks up and down.
C. Right Front Axle Clamp Bolts B. Block
D. Front Axle Nut
E. Left Front Axle Clamp Bolts
F. Oil Seals
• Tighten the right front axle clamp bolts to the spec-
ified torque.
• Remove
cycle.
the jack and stand supporting the motor- Tightening Torque
Right Front Axle Clamp Bolts:
• Before tightening the clamp bolts on the right fork
leg, loosen the right front axle clamp bolts, and
20 N·m (2.0 kgf·m, 15 ft·lb)
pump the forks up and down 4 or 5 times to allow

NOTE
the right fork leg to find a neutral position on the
front axle. Tighten the two clamp bolts alternately two times

WARNING
After servicing, it takes several applications
j of the brake lever before the brake pads con-
tact the disc, which could result in increased
stopping distance and cause an accident re-
sulting in injury or death. Do not attempt to
ride the motorcycle until a firm brake lever is
obtained by pumping the lever until the pads
are against the disc.
• Set the left fork damping adjuster and right fork

spring preload to the position recorded before re-
moving the front forks.
• Install the removed parts. A. Standard Fork Clamp Position
Optional Fork Springs
Various fork springs are available to achieve suit- Standard Fork Clamp Position
able front fork action in accordance with the rider’s 7 mm (0.28 in.)*
weight and track condition.
Harder springs stiffen the fork action and acceler- *: between the top end of the outer tube and upper
ate the rebound damping. surface of the steering stem head
Softer springs soften the fork action and slow down
the rebound damping. NOTE
Fork Clamp Position
Tighten the two clamp bolts alternately two times
Steering is greatly affected by the fork clamp posi-
tion (how much the outer fork tubes protrude above
the steering stem head). Install the fork tubes to the
standard fork position.
NOTICE
The right and left fork tubes must be adjusted
evenly.

Rebound Damping Adjustment

Rear Suspension (UNI-TRAK®) To adjust the rear shock absorber rebound damp-
ing, turn the rebound damping adjuster at the bottom
This motorcycle’s rear suspension system is called of the rear shock absorber with a flat-head screw-
j
“UNI-TRAK®” and consists of a rear shock absorber driver.
unit, a swingarm, two lever rods and a lever.
The operating characteristics of the UNI-TRAK®
suspension are similar to those of the front fork.
However, a linkage system is used to achieve pro-
gressive springing characteristics.
Rear Shock Absorber Inspection
• Pump the seat down and up by 4 or 5 times, and
inspect the smooth stroke.
• Iftheit oildoes not smoothly or noise is found, inspect
leak and rear shock absorber mounting.
• Visually
leakage.
inspect the rear shock absorber for oil
• IfKawasaki
necessary, repair or replace by an authorized
dealer.
A. Rebound Damping Adjuster
Rear Shock Absorber Adjustment
The spring preload of the shock absorber can be If the damping feels too soft or too stiff, adjust it in
adjusted or the spring can be replaced with an op- accordance with the following table.
tional one to suit various riding conditions. In addi-
tion, the damping force can be adjusted easily, mak-
ing it unnecessary to change the oil viscosity.

Rebound Damping Adjuster Settings NOTICE
Do not force the rebound damping force ad-
j juster beyond the fully seated position, or the
adjusting mechanism may be damaged.
NOTE
Adjustment of the rebound damping adjuster for
the rear suspension will slightly affect the com-
pression damping force. Always make any damp-
ing adjustments in small steps and test their ef-
fects before using them in competition.
Compression Damping Adjustment (Gas

Reservoir)
A. Seated Position (Adjuster Turned Fully There are two adjustments you can make to the
Clockwise) rear shock absorber gas reservoir.
B. Softer (Counterclockwise) To adjust the high speed compression damping,
C. Harder (Clockwise) turn the high speed compression damping adjuster.
D. Standard Setting To adjust the low speed compression damping,
*: Number of turns counterclockwise usable range turn the low speed compression damping adjuster
22 clicks or more. with a flat-head screwdriver.
If the damping feels too soft or too stiff, adjust it in
Standard Rebound Damping Adjuster Setting accordance with the following table.
11 clicks*

High Speed Compression Damping Adjuster

Settings
j
A. Compression Damping Adjuster for High Speed

B. Compression Damping Adjuster for Low Speed
If the damping feels too soft or too stiff, adjust it in A. Seated Position (Adjuster Turned Fully
accordance with the following table. Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range 4
turns or more.
Standard High Speed Compression Damping
Adjuster Setting
1 1/2 turns out*

Low Speed Compression Damping Adjuster NOTICE
Settings
Do not force the compression damping force
j adjuster beyond the fully seated position, or
the adjusting mechanism may be damaged.
NOTE
Adjustment of the compression damping adjuster
for the rear suspension will slightly affect the re-
bound damping force. Always make any damping
adjustments in small steps and test their effects
before using them in competition.
Spring Preload Adjustment

• Remove the rear frame with air cleaner housing
(see Throttle Body Assy section).
Clockwise) NOTICE
B. Softer (Counterclockwise) If the clamp is not removed from the air
cleaner housing, the rear shock absorber
D. Standard Setting
spring may be damaged.
19 clicks or more. • Raise the rear wheel off the ground using a jack
Standard Low Speed Compression Damping
Adjuster Setting cial tool: 57001-1252 or 1608).
11 clicks* • Using the hook wrenches (special tools: 57001
-1101, 1539), loosen the locknut on the rear shock
absorber.

• Using the hook wrench (special tool: 57001-1101),

turn the spring preload adjusting nut as required.
Turning the adjusting nut down increases the
spring preload.
j
A. Spring Preload Adjusting Nut

B. Locknut
C. Hook Wrenches (Special Tools: 57001-1101,
1539)
A. Hook Wrench (Special Tool: 57001-1101)

B. Spring Preload Adjusting Nut
• The standard adjusting nut position from the cen-

ter of the upper rear shock absorber pivot point is
129.5 mm (5.10 in.).
• The adjustable range is as shown in the table be-
low.

Rear Shock Absorber Spring Adjustable Range • Tighten the locknut securely.
K = 49 N/mm 125.8 a 135.8 mm Tightening Torque
j (K = 5.0 kgf/mm) (4.95 a 5.35 in.) Rear Shock Absorber Spring Locknut:
K = 51 N/mm 125.8 a 133.8 mm 45 N·m (4.6 kgf·m, 33 ft·lb)
(K = 5.2 kgf/mm) (4.95 a 5.27 in.)
K = 53 N/mm* 125.8 a 139.5 mm • After making the adjustment, move the spring up
and down to make sure that it is properly seated.
(K = 5.4 kgf/mm) (4.95 a 5.49 in.)
• Install the rear frame with air cleaner housing (see
Throttle Body Assy section).
K = 55 N/mm 125.8 a 139.6 mm
(K = 5.6 kgf/mm) (4.95 a 5.50 in.) • Install the removed parts.
Optional Rear Shock Absorber Springs
*: Standard Various rear shock absorber springs are available
to achieve suitable rear shock absorber action in ac-
cordance with the rider’s weight and track condition.
A harder spring stiffens the shock absorber action
and accelerates the rebound damping.
A softer spring softens the shock absorber action
and slows down the rebound damping.
WARNING
Improper removal or installation of the rear
shock absorber spring may cause the spring
and/or related parts to be ejected at high ve-
locity. Always wear eye and face protection
when working on the rear shock absorber.
Removal and installation of the rear shock
A. Adjusting Nut Position
absorber spring should be performed by an
B. Center of Upper Rear Shock Absorber Pivot
C. Spring End authorized Kawasaki dealer.

rim to warp, the nipples and spokes to fatigue more

Wheels quickly, and the spokes to break.
j
Tire Air Pressure
Tire air pressure affects traction, handling, and tire
life. Adjust the tire air pressure to suit track condi-
tions and rider preference, but keep it close within
the recommended range.
• To check the tire air pressure, remove the air valve
cap, and make sure to tighten the cap securely
after checking the tire pressure.
• Reduce the tire air pressure to increase the tire
tread surface on the ground when riding on a wet,
muddy, sandy or slippery track.
• Increase the tire air pressure to prevent damage
or punctures (though the tires will skid more easily)
when riding on a pebbly or hard track. A. Spoke Wrench
Tire Air Pressure Adjustable Range
Bead Protector
80 a 100 kPa (0.8 a 1.0 kgf/cm², 12 a 14 psi) There is a bead protector nut on the both wheels.
The bead protector nut prevents the tire and tube
NOTE from slipping on the rim and damaging the valve
Tire air pressure should be checked when the tires stem. Valve stem damage may cause the tube to
are cold, before you ride the motorcycle. leak, necessitating tube replacement. In order to
keep the tire and tube in position on the rim, inspect
Spokes and Rims the bead protector nut before riding and tighten it if
The spokes on both wheels must all be securely necessary. Tighten the valve stem nut finger tight
and evenly tightened and not be allowed to loosen. only.
Unevenly tightened or loose spokes will cause the

NOTE
The welding spot of the rim may show exces-
j sive runout. Disregard this when measuring rim
runout.
Rim Runout
A. Bead Protector Nut
Rim Runout
Set up a dial gauge on the side of the rim and
rotate the wheel to measure its axial runout. The
difference between the highest and lowest readings
is the amount of runout. A. Rim
• Set up the dial gauge on the inner circumference
of the rim and rotate the wheel to measure its ra-
B. Axial Runout
C. Radial Runout
dial runout. The difference between the highest
and lowest readings is the amount of runout. Rim Runout Maximum Limit
• A certain amount of rim warpage (runout) can be
corrected by recentering the rim, that is, by loos-
Axial
*TIR 2.0 mm (0.08 in.)
Radial
ening some spokes and tightening other to change
the position of certain portions of the rim. If the rim
is badly bent, however, it should be replaced. *: Total Indicator Reading

Hoses Inspection
Check the brake and fuel hoses for cracks or de-
j
terioration, and the connections for looseness in ac-
cordance with the Periodic Maintenance Chart.
• Inspect the brake hose and fittings for deteriora-
tion, cracks and signs of leakage by bending or
twisting the hoses.
• If damaged, replace the hoses.
A. Axial Rim Runout Measurement
A. Leak
B. Cracks
C. Bulges
• Check that the hose are securely connected and

bolts are tightened correctly.
A. Radial Rim Runout Measurement

Tightening Torques of Nuts and Bolts

j
Location of nuts and bolts
Before the first ride of each day of operation, check the tightness of the nuts and bolts shown below. Check
also that all cotter pins are in place and in good condition.
1. Front Fork Clamp Bolts 8. Spoke Nipples 13. Cylinder Bolt

2. Handlebar Clamp Bolts 9. Front Axle Clamp Bolts 14. Engine Oil Drain Bolt
3. Spark Plug 10. Front Brake Disc Mounting 15. Camshaft Chain Tensioner
4. Cylinder Head Cover Bolts Bolts Mounting Bolts
5. Cylinder Head Bolts 11. Front Axle Nut 16. Shift Pedal Bolt
6. Rear Frame Mounting Bolts 12. Front Caliper Mounting 17. Swingarm Pivot Shaft Nut
7. Rear Shock Absorber Nuts Bolts 18. Rear Sprocket Nuts

1. Muffler Mounting Bolts 6. Rear Master Cylinder 11. Brake Pedal Bolt
2. Muffler Clamp Bolt Mounting Bolts 12. Kick Pedal Bolt
3. Upper Engine 7. Rear Brake Disc Mounting 13. Clutch Cover Bolts
Mounting/Bracket Bolts Bolts 14. Coolant Drain Bolt
4. Steering Stem Head Nut 8. Rear Axle Nut 15. Lower Engine Mounting Nut
5. Front Master Cylinder 9. Rocker Arm Pivot Nut 16. Middle Engine
Clamp Bolts 10. Tie-Rod Mounting Nuts Mounting/Bracket Nuts

Torque table
Tighten all nuts and bolts to the proper torque using an accurate torque wrench. An insufficiently tightened
nut or bolt may become damaged or fall out, possibly resulting in damage to the motorcycle and injury to the
j rider. An overtightened nut or bolt may become damaged, broken, or fall out.
Fastener N·m kgf·m ft·lb Remarks
Engine
Coolant Drain Bolt 7.0 0.71 62 in·lb
Camshaft Chain Tensioner Cap Bolt 20 2.0 15
Camshaft Chain Tensioner Mounting Bolts 9.8 1.0 87 in·lb
Cylinder Bolt 12 1.2 106 in·lb S
Cylinder Head Bolts (M10) 49 5.0 36 MO, S
Cylinder Head Bolts (M6) 12 1.2 106 in·lb S
Cylinder Head Cover Bolts 9.8 1.0 87 in·lb
Clutch Cover Bolts 9.8 1.0 87 in·lb
Clutch Spring Bolts 9.0 0.92 80 in·lb
Engine Oil Drain Bolt 20 2.0 15
Oil Filler Plug 5.0 0.51 44 in·lb
Oil Filter Cover Bolts 9.8 1.0 87 in·lb
Kick Pedal Bolt 25 2.5 18 L
Shift Pedal Bolt 9.8 1.0 87 in·lb
Flywheel Nut Cap 4.9 0.50 43 in·lb
Spark Plug 13 1.3 115 in·lb
Timing Inspection Cap 3.9 0.40 35 in·lb


Chassis
Air Cleaner Duct Clamp Screw 2.0 0.20 18 in·lb
j
Throttle Body Assy Holder Clamp Screw 2.0 0.20 18 in·lb
Muffler Clamp Bolt 11 1.1 97 in·lb S
Muffler Mounting Bolts 21 2.1 15 S
Engine Mounting Nut (Lower) 49 5.0 36 R, S
Engine Bracket Nuts (Middle) 29 3.0 21 R, S
Engine Mounting Nut (Middle) 49 5.0 36 R, S
Engine Bracket Bolts (Upper) 29 3.0 21 S
Engine Mounting Bolts (Upper) 49 5.0 36 S
Front Axle Clamp Bolts 20 2.0 15 AL
Front Axle Nut 78 8.0 58
Rear Axle Nut 108 11.0 80
Spoke Nipples 2.2 0.22 19 in·lb
Rear Sprocket Nuts 34 3.5 25 R
Brake Pedal Bolt 25 2.5 18 G, L
Front Brake Disc Mounting Bolts 9.8 1.0 87 in·lb L
Front Caliper Mounting Bolts 25 2.5 18
Front Master Cylinder Clamp Bolts 8.8 0.90 78 in·lb S
Rear Brake Disc Mounting Bolts 23 2.3 17 L
Rear Master Cylinder Mounting Bolts 9.8 1.0 87 in·lb
Front Fork Clamp Bolts (Lower) 23 2.3 17 AL


Front Fork Clamp Bolts (Upper) 23 2.3 17 AL, L
j Rear Shock Absorber Nut (Lower) 34 3.5 25 R
Rear Shock Absorber Nut (Upper) 39 4.0 29 R
Rocker Arm Pivot Nut 59 6.0 44 G, R
Swingarm Pivot Shaft Nut 98 10.0 72 R
Tie-Rod Mounting Nuts 59 6.0 44 G, R
Handlebar Clamp Bolts 25 2.5 18 AL
Steering Stem Head Nut 98 10.0 72
Rear Frame Mounting Bolts 34 3.5 25
AL: Tighten the two clamp bolts alternately two times to ensure even tightening torque.
G: Apply grease.
L: Apply a non-permanent locking agent.
MO: Apply molybdenum disulfide oil solution (mixture of the engine oil and molybdenum disulfide grease in
a weight ratio 10:1).
R: Replacement Parts
S: Follow the specified tightening sequence.

Cleaning Your Motorcycle

• Avoid applying degreaser to seals, brake pads,
and tires.
• Avoid all harsh chemicals, solvents, detergents,
and household cleaning products such as ammo-
j
General Precautions nia-based window cleaners.
Frequent and proper care of your Kawasaki mo-
torcycle will enhance its appearance, optimize over- • Gasoline, brake fluid, and coolant will damage the
finish of painted and plastic surfaces: wash them
all performance, and extend its useful life. Covering
off immediately.
your motorcycle with a high quality, breathable mo-
torcycle cover will help protect its finish from harmful • Avoid wire brushes, steel wool, and all other abra-
sive pads or brushes.
UV rays, pollutants, and reduce the amount of dust
reaching its surfaces. • Use care when washing the plastic parts as they
can easily be scratched.
WARNING • Avoid using pressure washers; water can pene-
trate seals and electrical components and damage
Build-up of debris or flammable material in your motorcycle.
and around the vehicle chassis, engine, and
exhaust can cause mechanical problems and
• Avoid spraying water in delicate areas such as
in air intakes, throttle body assy, brake compo-
increase the risk of fire. nents, electrical components, muffler outlets, and
When operating the vehicle in conditions fuel tank openings.
that allow debris or flammable material to
collect in and around the vehicle, inspect the Washing Your Motorcycle
engine, electrical component and exhaust • Rinse your bike with cold water from a garden
hose to remove any loose dirt.
areas frequently. If debris or flammable
materials have collected, park the vehicle • Mix a mild neutral detergent (designed for motor-
cycles or automobiles) and water in a bucket. Use
outside and stop the engine. Allow the
engine to cool, then remove any collected a soft cloth or sponge to wash your motorcycle. If
debris. Do not park or store the vehicle in needed, use a mild degreaser to remove any oil or
an enclosed space prior to inspecting for grease which build up.
build-up of debris or flammable materials. • After washing, rinse your motorcycle thoroughly
with clean water to remove any residue (residue
from the detergent can damage parts of your mo-
• Be sure the engine and exhaust are cool before
washing. torcycle).

• Use a soft cloth to dry your motorcycle. As you dry,

inspect your motorcycle for chips and scratches.
NOTICE
Plastic parts may deteriorate and break if
Do not let the water air dry as this can damage
j the painted surfaces.
they come in contact with chemical sub-
stances or household cleaning products
• Start the engine and let it idle for several minutes.
The heat from the engine will help dry moist areas.
such as gasoline, brake fluid, window clean-
ers, thread-locking agents, or other harsh
• Carefully ride your motorcycle at a slow speed and
apply the brakes several times. This helps the
chemicals. If a plastic part comes in contact
with any harsh chemical substance, wash it
brakes dry and restores its normal operating per-
off immediately with water and a mild neu-
formance.
tral detergent, and then inspect for damage.
• Lubricate the drive chain to prevent rusting.
Avoid using abrasive pads or brushes to
NOTE clean plastic parts, as they will damage the
After riding in an area where the roads are salted part’s finish.
or near the ocean, immediately wash your motor-
cycle with cold water. Do not use warm water as it Chrome and Aluminum
accelerates the chemical reaction of the salt. Af- Chrome and uncoated aluminum parts can be
ter drying, apply a corrosion protection spray on all treated with a chrome/aluminum polish. Coated
metal and chrome surfaces to prevent corrosion. aluminum should be washed with a mild neutral de-
tergent and finished with a spray polish. Aluminum
Painted Surfaces wheels, both painted and unpainted can be cleaned
After washing your motorcycle, coat painted sur- with special non-acid based wheel spray cleaners.
faces, both metal and plastic, with a commercially
available motorcycle/automotive wax. Wax should Leather, Vinyl, and Rubber
be applied once every three months or as conditions If your motorcycle has leather accessories, special
require. Avoid surfaces with “satin” or “flat” finishes. care must be taken. Use a leather cleaner/treatment
Always use non-abrasive products and apply them to clean and care for leather accessories. Washing
according to the instructions on the container. leather parts with detergent and water will damage
them, shortening their life.
Plastic Parts Vinyl parts should be washed with the rest of the
After washing use a soft cloth to gently dry plastic motorcycle, then treated with a vinyl treatment.
parts. When dry, treat the non-painted plastic parts
with an approved plastic cleaner/polisher product.

The sidewalls of tires and other rubber compo-

nents should be treated with a rubber protectant to Lubrication
help prolong their useful life.
Lubricate the areas shown in the illustrations of
j
WARNING this section with either motor oil or regular grease,
Rubber protectants can be slippery and, if after each race and whenever the vehicle has been
used on the tread area, cause loss of traction operated under wet or rainy conditions, especially
resulting in accident causing injury or death. after using a high-pressure spray washer. Before
Do not apply rubber protectant to any tread lubricating a part, clean off any rust with rust remover
area. and wipe off any grease, oil, dirt, or grime.
General Lubrication
Apply motor oil to the following pivots:
• Clutch Lever
• Front Brake Lever

• Rear Brake Pedal • Shift Pedal

• Kick Pedal Cylinder Joint Pin
Rear Master
j • Footpeg
•
Apply an aerosol cable lubricant with a pressure

lubricator on all cables:
• Clutch Cable
• Throttle Cable

Cable Lubrication Apply grease to the following points:

• Clutch Inner Cable Upper End
• Throttle Inner Cable Upper End
j
A. Upper End
Drive Chain Lubrication

Lubricate the drive chain after riding through rain
or on wet track, or any time that the chain appears
dry. A heavy oil such as SAE90 is preferred to a
lighter oil because it will stay on the chain longer and
provide better lubrication.
• Apply oil to the sides of the rollers so that it will
penetrate to the rollers and bushings.
• Wipe off any excess oil.

DFI Self-Diagnosis
j This motorcycle equips the DFI trouble self
-diagnosis system. Trouble diagnosis can be con-
ducted with the optional parts sold separately as the
following procedures.
Self-diagnosis Outline
The self-diagnosis has two modes and can
be switched to another mode by grounding the
self-diagnosis terminal.
User Mode -
The ECU connected FI indicator light goes on
when DFI system and ignition system and ignition
system parts are faulty. In case of serious troubles,
the ECU stops the injection/ignition operation.
Dealer Mode -
The FI indicator light emits service code(s) to show
the problem(s) which the DFI system, and ignition
system has at the moment of diagnosis.
Self-diagnosis Procedures
•Remove the number plate (see Steering section).
•Disconnect the connector.
•Connect the FI indicator light assy (optional part:
23016-0049) (or and the sub harness (optional
part: 26011-0315)) (see WIRING DIAGRAM
chapter).

• Connect the power supply harness (optional part:

26011-0246) to the capacitor lead connector of the
main harness.
j
• Connect the power supply harness (optional part:
26011-0246) to the 12 V battery as shown in the
figure.
A. Connector
• Disconnect the capacitor lead connector.
A. Power Supply Harness (Optional Part:

26011-0246)
B. Capacitor Lead Connector
C. 12 V Battery
NOTE
Use a fully charged battery when conducting self
-diagnosis. Otherwise, the light blinks very slowly
or doesn’t blink.
Keep the self-diagnosis terminal grounded during
self-diagnosis.
A. Capacitor Lead Connector

• Keep the FI indicator light assy (optional part:

23016-0049) Y lead ground.
j • Count the blinks of the light to read the service
code. Keep the lead ground until you finish read-
ing the service code.
• To enter the self-diagnosis dealer mode, ground
the self-diagnosis terminal for more than 2 sec-
onds, and then keep it grounded continuously.
A. Y Lead
B. 2 Seconds
C. Keep it grounded continuously

How to Read Service Codes
• Service codes are shown by a series of long and short blinks of the FI indicator light as shown below. j
• Read 10th digit and unit digit as the FI indicator light blinks.
• When there are a number of problems, all the service codes can be stored and the display will begin
starting from the lowest number service codes in the numerical order. Then after completing all codes, the
display is repeated until the self-diagnosis terminal is open.
• If there is no problem, no code and unlight.
• For example, if two problems occurred in the order of 21, 12, the service codes are displayed from
the lowest number in the order listed.
(12 21) (12 21) ··· (repeated)
• doesn’t
If the problem is with the following parts, the ECU cannot memorize these problems, the FI indicator light
go on, and no service codes can be displayed.
ECU Power Source Wiring and Ground Wiring (see Service Manual)

NOTE
Even if the battery or the ECU are disconnected, or the problem is solved, all service codes remain in the
j ECU.
Service Code Table

Service
FI Indicator Light Problems
Code
11 Throttle sensor malfunction, wiring open or short
Intake air pressure sensor malfunction, wiring open or

12
short
Intake air temperature sensor malfunction, wiring open
13
or short
Water temperature sensor malfunction, wiring open or
14
short
21 Crankshaft sensor malfunction, wiring open or short
25 Gear position switch malfunction, wiring open or short
31 Vehicle-down sensor malfunction, wiring open or short
41 Downstream injector malfunction, wiring open or short

Service
FI Indicator Light Problems
Code
j
42 Upstream injector malfunction, wiring open or short
46 Fuel pump malfunction, wiring open or short
51 Ignition coil malfunction, wiring open or short
NOTE
The ECU may be involved in these problems. If all the parts and circuits checked out good, be sure to check
the ECU for ground and power supply. If the ground and power supply are checked good, replace the ECU
(see Service Manual).
When no service code is displayed, the electrical parts of the DFI system has no fault, and the mechanical
parts of the DFI system and the engine are suspect.
A bracket to fix the FI indicator light on the handlebar is sold separately as an optional part.
Bracket (Optional Part): Part No. – 11055-1673

164 TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
NOTE Spark missing or weak:
This troubleshooting guide is not exhaustive and •Spark plug dirty, broken, or gap improperly ad-
justed
j does not give every possible cause for each prob-
lem listed. It is meant simply as a quick guide to •Spark plug cap or high-tension wiring defective
assist you in troubleshooting for some of the more •Spark plug cap not contacting properly
common difficulties. •Spark plug type incorrect
•Crankshaft sensor defective
Starting failure or difficulties - •ECU defective
•Ignition coil defective
Engine does not turn over:
• Valve •Engine stop button wiring defective
seized
• Cylinder or seized •Flywheel magneto damaged
Valve lifter
• Crankshaft seized
piston seized
•Wiring shorted or interrupted
• Connecting rod small end seized Fuel/air mixture incorrect:

• Connecting rod big end seized • Air cleaner element clogged, poorly sealed, or not
• Camshaft seized installed
• Transmission gear or bearing seized
• Kick shaft return spring broken Compression low:
• Kick ratchet gear not engaging •Spark plug loose
• Improper installation of vehicle-down sensor •Cylinder head insufficiently tightened
• •Cylinder bolt loose
•Cylinder or piston worn
Fuel does not flow:
• No •No valve clearance
fuel in tank
• Fuel tank •Crankshaft oil seal leak
Fuel cap air vent obstructed
• Break down of a fuel pump •Valve spring broken or weak
line clogged
• Break down of a upstream injector and/or down- •Valve not seating properly (valve bent, worn, or
carbon accumulation on the seating surface)
• stream injector •Piston ring worn, weak, broken, or sticking
•Piston ring side clearance excessive
•Cylinder head gasket damaged

TROUBLESHOOTING GUIDE 165
• Cylinder head warped • Valve not seating properly (valve bent, worn, or
• Decompression damaged
Cylinder gasket carbon accumulation on the seating surface)
• trouble • Piston ring worn, weak, broken, or sticking
Poor low-speed performance - • Cylinder head
Piston ring side clearance excessive
• Cylinder head gasket damaged
Spark weak: • Cylinder gasketwarped j
• Spark plug dirty, broken, or gap improperly ad- • Decompression damaged
justed • trouble
• Spark plug cap or high-tension wiring defective
• Spark plug cap
Spark plug shorted or not contacting properly Other:
• Crankshaft sensorincorrect
type •ECU defective
• ECU defective defective •Brake dragging
• Ignition coil defective •Clutch slipping
• Flywheel magneto defective •Engine overheating
• Wiring connector not in good contact •Engine oil level too high
• •Engine oil viscosity too high
Fuel/air mixture incorrect:

•Drive chain trouble
Poor or no high-speed performance -
• Air cleaner element clogged, poorly sealed, or not
installed Firing incorrect:
• Fuel tank cap air vent obstructed • Spark plug dirty, broken, or gap improperly ad-
• Air cleaner
Throttle body assy holder loose justed
• Fuel pump defective
duct loose • Spark plug cap or high-tension wiring defective
• • Spark plug cap shorted or not contacting properly
• Spark plug type incorrect
Compression low: • ECU defective
•Spark plug loose • Ignition coil defective
•Cylinder head insufficiently tightened • Crankshaft sensor defective
•Cylinder bolt loose • Flywheel magneto defective
•Cylinder or piston worn • Wiring connector not in good contact
•No valve clearance
•Valve spring broken or weak

Fuel/air mixture incorrect: • Engine oil level too high
• Air cleaner element clogged, poorly sealed, or not • Crankshaftviscosity
Engine oil too high
installed • Drive chain trouble or damaged
bearing worn
• Fuel contaminated with water or foreign matter •
• Fuel tank cap air vent obstructed
j • Throttle body assy holder loose Knocking:
• Air cleaner duct loose •Carbon built up in combustion chamber
• Fuel line clogged •Fuel quality poor or type incorrect
• Fuel pump defective •Spark plug type incorrect
Compression low:
•ECU defective
Engine overheating -
• Spark plug loose
• Cylinder head
Cylinder insufficiently tightened Firing incorrect:
• Cylinder or piston worn
bolt loose • Spark plug dirty, broken, or gap improperly ad-
• No valve clearance justed
• Valve spring broken or weak • Spark plug type incorrect
• Valve not seating properly (valve bent, worn, or • ECU defective
• carbon accumulation on the seating surface) Fuel/air mixture incorrect:
• Piston ring worn, weak, broken, or sticking • Throttle body assy holder loose
• Cylinder head
Piston ring side clearance excessive • Air cleaner element clogged, poorly sealed, or not
• Cylinder head gasket damaged installed
• Cylinder gasket damaged
warped • Air cleaner duct poorly sealed
• Decompression trouble
• Compression high:
Improper acceleration:
•Carbon built up in combustion chamber
• Throttle valve does not fully open Engine overloaded:

• Air cleaner element clogged •Brake dragging
• Fuel contaminated with water or foreign matter •Clutch slipping
• Brake dragging •Engine oil level too high
• Clutch slipping •Engine oil viscosity too high
• Engine overheating •Drive chain trouble

• Clutch hub nut loose

Lubrication inadequate: • Clutch hub spline
Clutch plate warped or rough
• Engine oil level too low • damaged
• Engine oil quality poor or type incorrect
Gear shifting faulty -
Coolant inadequate: Transmission does not go into gear; shift pedal
j
•Coolant level too low does not return:
•Coolant deteriorated • Clutch not disengaging
• Shift fork bent or seized
Cooling system component defective: • Gear stuck on the shaft
•Radiator clogged • Shift lever broken
•Radiator cap defective • Pawl guide plate broken
•Water pump not rotating • Shift return spring broken or weak
Clutch operation faulty - • Shift return spring pin loose
• Shift pawl broken
Clutch slipping: • Shift pawl spring weak
• No clutch lever play • Shift drum broken
• Clutch cable improperly adjusted • Gear positioning lever operation defective
• Clutch cable defective
• Clutch plate worn or warped Transmission jumps out of gear:
• Clutch spring broken or weak • Shift fork worn
• Clutch release mechanism defective • Gear groove worn
• Clutch hub or housing unevenly worn • Gear dogs and/or dog grooves worn
• Shift drum groove worn
Clutch not disengaging properly: • Gear positioning lever spring broken or weak
• Clutch lever play excessive • Shift fork guide pin worn
• Clutch spring tension uneven • Drive shaft, output shaft, and/or gear splines worn
• Engine oil deteriorated
• Engine oil viscosity too high Transmission skips gears:
• Engine oil level too high • Gear positioning lever spring broken or weak
• Clutch housing frozen on drive shaft • Pawl guide plate worn
• Clutch release mechanism defective

Engine noise abnormal - • Camshaft chain, sprocket, chain guide worn
Knocking: • Flywheel magnetospring
Decompression broken
•Carbon built up in combustion chamber • loose
•Fuel quality poor or type incorrect Abnormal drive train noise -

•Spark plug type incorrect
Clutch noise:
j •Engine overheating
• Clutch housing/friction plate clearance excessive
•ECU defective
• Metal chip
Clutch housing gear excessive
Piston slap: • jammed in clutch housing gear teeth
• Piston clearance excessive

Transmission noise:
• Cylinder or piston worn
• Crankcase bearing worn or damaged
• Connecting rod bent
• Transmission gear worn or chipped
• Piston pin or piston pin holes worn
• Engine oil level or viscosity
Metal chip jammed in gear teeth
Valve noise: • Kick ratchet gear not properlytoo low
• Valve clearance incorrect • kick gear disengaging from
• Valve spring broken or weak

• Kick shaft idle gear worn or chipped
• Camshaft bearing or cam face worn
• Valve lifter worn
Drive chain noise:
Other noise: • Drive chain slack improperly adjusted
•Connecting rod small end clearance excessive • Drive chain worn
•Connecting rod big end clearance excessive • Rear and/or engine sprocket(s) worn
•Piston ring worn, broken or stuck • Drive chain inefficiently lubricated
•Piston seized or damaged • Rear wheel misaligned
•Cylinder head gasket leaking Frame noise abnormal -

•Exhaust pipe leaking at cylinder head
Front fork noise:
•Crankshaft runout excessive
• Oil level or viscosity too low
•Engine mounts loose
• Spring broken or weak
•Crankshaft bearing worn
• Front fork air pressure high
•Primary gear worn or chipped
•Camshaft chain tensioner defective

Rear shock absorber noise: • Steering stem bearing damaged

•Shock absorber damaged • Steering stem bearing
Steering stem inadequately lubricated
• Tire air pressure too low
bent
Disc brake noise: •
• Pad installed incorrectly
• Pad surface glazed Handlebar shakes or vibrates excessively:
j
• Brake disc warped •Tire worn
• Brake caliper defective •Swingarm sleeve or needle bearing damaged
• Brake cylinder damaged •Rim warped or out of balance
•Front and/or rear axle runout excessive
Other noise: •Wheel bearing worn
• Bracket, nut, bolt, etc. improperly mounted or •Handlebar clamp loose
tightened •Steering stem head nut loose
Exhaust smoke - •Spoke loose
Excessively white: Handlebar pulls to one side:

•Piston oil ring worn •Frame bent
•Cylinder worn •Rear wheel misaligned
•Valve oil seal damaged •Swingarm bent or twisted
•Valve guide worn •Swingarm pivot shaft runout excessive
•Engine oil level too high •Steering maladjusted
•Steering stem bent
Black smoke: •Front fork bent
• Air cleaner element clogged
Shock absorption unsatisfactory (suspension
Brownish: too hard):
• Air cleaner duct loose • Front fork oil excessive
• Air cleaner poorly sealed or missing • Front fork oil viscosity too high
Poor handling and/or stability - • Front fork bent
• Front fork air pressure too high
Handlebar hard to turn: • Tire air pressure too high
•Cable, hose, wiring incorrectly routed • Rear shock absorber improperly adjusted
•Steering stem nut too tight

Shock absorption unsatisfactory (suspension Poor braking performance -
too soft):
• Front fork oil level insufficient and/or front fork • Air in the brake line
leaking oil • Brake pad or disc worn
• Front fork oil viscosity too low • Brake fluid

Brake leaking
• Front fork and/or rear shock absorber spring weak • Brake pads contaminated
disc warped
j
• Rear shock absorber leaking oil or gas • Brake fluid deteriorated
• Rear shock absorber improperly adjusted • Primary and/or secondary master cylinder cup(s)
• Tire air pressure too low • damaged
• Master cylinder scratched
• Brake maladjusted (lever or pedal play excessive)

TUNING 171
TUNING
Suspension
• The front and rear suspension should always be
balanced; when the one is changed, the other one
might need to be changed similarly.
Introduction • When evaluating suspension performance, the
rider must make every effort to ride consistently
No area of machine adjustment is more critical
and to recognize the effects of his input. Such
than proper suspension tuning. An improperly tuned
things as changes in rider position and increasing j
suspension will keep even the best rider from attain-
fatigue may lead to incorrect judgments about
ing the full benefit of his machine’s ability. Match the
necessary adjustments.
suspension to the rider and the course conditions.
• When the proper settings have been determined
for a particular track, they should be written down
WHILE TUNING THE SUSPENSION, KEEP THE
for reference when returning to the same track.
FOLLOWING IMPORTANT POINTS IN MIND:
•If the machine is new, “break-in” the suspension • Lubricate the bearings in the swingarm and UNI
-TRAK® linkage after break-in and after every 3
with at least one hour of riding before making any
races to prevent friction from affecting suspension
setting evaluations or changes.
performance.
•The three major factors which must be considered
in suspension tuning are RIDER WEIGHT, RIDER Front Fork
ABILITY, and TRACK CONDITIONS. Additional
Front Fork Oil Capacity -
influences include the RIDER’S STYLE and PO-
The fork oil capacity in the fork tube is adjustable.
SITIONING on the machine.
A change in the fork oil level will not affect the spring
•Before changing the suspension settings, test
changing your riding posture or position to check
force much at the top of fork travel, but it will have a
great effect at the bottom of it.
whether it is the cause of the problem or not.
•It is a wise practice to adjust the suspension to • When the oil capacity is raised, the air spring be-
comes more progressive, and the front fork action
suit the rider’s strong points. If you are fast in
feels “harder” in the later stage of fork travel, near
the corners, adjust the suspension to allow fast
the bottom.
cornering.
•Make setting changes in small increments. A little • When the oil capacity is lowered, the air spring be-
comes less progressive, and the front fork action
bit goes a long way, and a setting is easily over
adjusted.

172 TUNING
does not feel as “hard” in the later stage of fork Troubleshooting Improper Settings
travel. Listed below are some symptoms of improper sus-
Fork Oil Capacity Effect on Fork Stroke pension settings and the most likely means of cor-
recting them. The proper settings can be achieved
by applying the information given in this chapter in a
scientific, methodical manner. This does not mean,
however, that you must be a scientist or trained tech-
nician to succeed. Simply take time to think about
the changes you believe are necessary, check them
j against the symptoms and cures described here,
make the changes in small increments, and take
note of the changes and their effects.
Front Fork Improper Adjustment Symptoms -
Too Hard
Spring too stiff:
• Rebound or compression damping improperly ad-
justed.
A. Weight • Spring too hard
B. Fork Stroke
C. Increase Capacity
• Fork oil capacity too high
D. Standard Oil Capacity Suspension stiffens at the end of the fork stroke:
E. Decrease Capacity • Fork oil capacity too high
Changing the fork oil capacity works effectively at • air pressure high
Fork
the end of fork travel. If fork bottoming is experi- Spring OK, but suspension too hard:
enced, raise the fork oil capacity. This will change • Fork oil deteriorated
the secondary spring rate. • Springairpreload
Fork pressure high
Front Fork Oil Capacity Adjustment - • too hard
• Adjust the front fork oil capacity (see Front Sus-

pension section).
Too Soft
The front fork dives excessively during braking
and deceleration:
• Fork oil capacity too low

TUNING 173
• Springs too soft Hence, if the actual rider weighs considerably more
• Rebound and/or compression damping improperly
Fork oil deteriorated or less, or if his riding experience and ability are
• adjusted. much above or below the intermediate level, it is
likely that a few basic suspension adjustments will
• Spring preload too soft be necessary.
Rear shock absorber improper adjustment Basic Readjustment of the Suspension
symptoms - Suspension Tuning According to Ground
Too Hard Surface
Suspension too stiff: j
Smooth Terrain Softer spring
• Compression damping too high
• Spring too hard Rough Terrain Harder spring
Spring OK but suspension too hard:
• Unbalance between the spring and the rebound
damping (rebound damping too hard)
Suspension
Experience
Tuning According to Riding
• Spring preload too hard Beginner

Softer spring with
greater rebound
Too Soft damping
Bottoming occurs on landing after a high jump
Experienced Rider Harder spring
(otherwise OK):
• Spring preload too soft or compression damping
too soft Suspension Tuning According to Rider Weight
• Spring too soft Heavy Rider Harder spring
• Shock absorber oil deteriorated
Light Rider Softer spring
Determining the Proper Settings
Standard Settings
From the factory, the machine is set up for a
medium-weight rider with intermediate riding ability.

174 TUNING
Suspension Tuning According the Type of Front and Rear Suspension Compatibility
Course Inspection
Lower the front end slightly Use this procedure to determine if the suspension
(Increase the amount of fork is balanced reasonably well.
tube protrusion above the • Hold the motorcycle upright (remove the side
stand.).
Many Corners steering stem head by 5 mm
(0.20 in.).). This accelerates • While standing next to the machine, lightly pull the
brake lever, place one foot on the footpeg closest
steering and enhances
turning ability. to you, and push down hard. If the motorcycle
j stays level as the suspension is compressed, the
Raise the front end slightly spring rates are well balanced.
(Decrease the amount of
fork tube protrusion above • Sit astride the motorcycle, take a riding posture
and check that the machine is in a horizontal po-
Fast Course the steering stem head by 5 sition. If one end drops noticeably more than the
mm (0.20 in.).). This slows other, the front and rear are not compatible and
down steering and enhances must be readjusted to achieve a better balance.
stability at high speed.
Deep Dips or Raise the front end slightly to
Sandy Ground gain stability.
Begin the actual on-track testing and evaluation

after making these preliminary adjustments.
Bear in mind the following points when readjusting
the suspension.
• Always make changes in small steps.
• The rider must be consistent in evaluating suspen-
sion performance.
• A change in the front suspension might require
one in the rear suspension, and vise versa.

TUNING 175
Although this is one of the most effective adjust- • Decrease the fork oil capacity.
ment procedures, suspension settings may vary de-
pending on the conditions at the track and the rider’s
• preload.
Use a softer spring, or decrease the spring
preferences.
NOTE
Front and Rear Suspension Troubleshooting Lighter or less experienced riders may need a
Front End Surges Downhill or During softer spring, or decrease the spring preload.
Acceleration Out of Corner -
The front suspension is too soft. Front End Does Not Respond to Small Bumps in
j
• Increase the compression damping or rebound
damping.
Sweeping Turns -
The front suspension is too hard.
• Increase the fork oil capacity. • Decrease the compression damping or rebound
• Use an optional harder spring, or increase the
spring preload. •
damping.
Decrease the fork oil capacity.
Front End “Knifes” or Oversteers in Turns • Use a softer spring, or decrease the spring
preload.
(Tends to Turn Inward) -
The front suspension is too soft. Rear End “Kicks” When Braking on Bumps -
• Increase the compression damping or rebound
damping.
The rear shock absorber rebound damping may be
too low.
• Increase the fork oil capacity. • Increase the rebound damping.
NOTE Rear Tire Does Not “Hook Up” Out of Corners
(Lack of Traction Coming Out of Turns) -
Heavier or expert riders may need a harder spring, The rear shock absorber may be too stiff.
or increase the spring preload.
• Decrease the rear shock absorber spring preload.
Front End Pushes or “Washes Out” in Turns • Decrease the high speed/low speed compression
damping.
(Front Wheel Tends to Push Outward Rather
than “Bite” in a Turn) - • Use a softer spring (lightweight rider only).
The front suspension is too stiff. Fork Bottoms Off After a High-speed Jump (may
• Decrease the compression damping or rebound
damping.
be due to improper riding posture) -
The rebound damping is too soft or the spring is
• Release some air from the fork tubes. too hard.

176 TUNING
• Increase the rebound damping. Rear End Bottoms After 3 or 4 Successive

• Decrease the
Decrease rear shock absorber spring preload. Jumps -
• the compression damping. • Decrease the rebound damping.
Front and Rear Ends Bottom Off After a NOTE
High-speed Jump (harsh bottoming occurs The rear shock absorber behavior on this machine
once or twice per lap) - may mislead some riders.
The front suspension is too soft. The rear shock absorber bottoms (due to full
• Increase the fork oil capacity. stroke) when the spring and damping are over-
j • Increase the front fork spring preload or use a come by the total weight of the machine and rider.
harder spring. A bottoming sensation (even though the machine
is actually not bottoming) may be caused by ma-
The rear suspension is too soft. chine weight and the inability of the rider to over-
• Increase the rear shock absorber spring preload
or use a harder spring.
come an overly stiff spring or excessive damping.
Observe the rear end jumps and try lowering the
• Increase the rear shock absorber high speed com-
pression damping or use a harder spring.
spring preload and damping if it does not approach
bottoming.
NOTE
Check the front and rear suspension compatibility
after making any adjustment.
Rear End Feels Soft at Small Jump -

• Increase the spring preload up to maximum.
• Increase the rear shock absorber low speed com-
pression damping.
Rear End Feels Soft at Large Jump -
•Increase the spring preload up to maximum.
•Increase the rear shock absorber high speed com-
pression damping.

TUNING 177
Gearing
• Since it is difficult to set the machine so it is best
suited for all portions of the circuit, determine
which circuit portions will have the greatest ef-
fect on lap time, and tune the machine to these
Selection of the Secondary Reduction Ratio portions. Confirm your settings by recording lap
(Rear Sprocket) times after each change. In this way the machine
Rear Sprocket Selection According to Course will deliver best performance for the entire circuit.
Conditions
Fast Course Small sprocket
j
Many Curves or Hills
Large sprocket
Sandy or Soft Ground
• Ifondary
the course has long straight portions, the sec-
reduction ratio should be reduced so that
the machine speed can be increased.
• Ifis then the course has many corners or uphills or
wet, the secondary reduction ratio should be
increased so that gear shifting and acceleration
are smooth.
• Since the speed must be changed depending on
the ground condition on the day of the race, be
sure to run through the circuit prior to a race and
tune the machine accordingly.
• If there is a long straight portion of the course on
which the machine can be run at maximum speed,
the machine should be set so that the maximum
speed is developed toward the end of the straight
course, but care should be taken not to over-rev
the engine.

178 TUNING
Special Care According to Track

• The engine works hardest in muddy conditions
and the radiator can become clogged with mud.
Conditions Take care not to overheat the engine in these con-
ditions. The engine also works very hard when
• Infinedry,powdery
dusty conditions (such a volcanic ash or riding in deep sand.
dust), special care must be given to
keeping the air cleaner element clean.
• In muddy or sandy conditions, increase chain
slack as the chain and sprockets will be packed
• When riding on wet, heavy clay, mud adheres to with mud or sand, which reduces chain slack.
j
the tires and other parts of the vehicle. The mud
can add significantly to the weight of the vehicle
• Check chain and sprocket wear frequently when
riding in mud or sand, since wear is increased in
and therefore reduce performance. Take care to these conditions.
remove built-up mud from the tires and chassis
after each ride, before drying occurs.

OPTIONAL PARTS 179
OPTIONAL PARTS
Engine Sprocket Suspension Spring (N/mm)
12T K = 9.1
13T (Standard) Front K = 9.5 (Standard)
Rear Sprocket K = 9.9
48T K = 49
49T K = 51
Rear
Aluminum 50T (Standard) K = 53 (Standard)
51T K = 55
52T Disc Plate
48T Front No holes (for wet conditions)
49T Rear No holes (for wet conditions)
Steel 50T Aluminum Nipple Wheel (Without Tire)
51T Front 21 × 1.60
52T Rear 19 × 1.85
Handlebar Holder and Clamp Spoke Nipple
Clamp (Upper) Size 28.6 Front and Rear Steel
28.6
Holder (Lower) Size KX FI Calibration Kit
22.2 The KX FI Calibration Kit can change the ECU data
setting, and save and analyze the engine operation
data in a personal computer (PC).
KX FI Calibration Kit: Part No. – 99999-0334
For details, refer to the KX FI Calibration Kit man-
ual.

180 PRE-RACE CHECKS AND AFTER-RACE MAINTENANCE
PRE-RACE CHECKS AND AFTER-RACE MAINTENANCE

Pre-Race Checks - Maintenance After the First Race -
• Front axle nut, or axle clamp bolt torque •Clean the air cleaner element.
• Front fork clamp bolt torque •Adjust the drive chain slack.
• Handlebar clamp bolt torque •Torque the rear sprocket nuts.
• Throttle grip screw tightness •Torque the spokes.
• Throttle grip operation •Check the front and rear tire air pressure.
• Front and rear brake hose installation •Torque the front and rear axle nuts.
• Front and rear brake fluid level •Torque the swingarm pivot shaft nut.
• Front and rear brake disc and caliper installation •Torque the muffler and exhaust pipe bolts and
• Front and rear brake function nuts.
• Fuel tank installation •Tighten the front and rear fender bolts.
• All control cable routings •Tighten the fuel tank and seat bolts.
• Engine mounting bolt torque •Check the front and rear brake function.
• Engine sprocket installation •Check the steering play.
• Shift pedal bolt torque •Fill the fuel tank with fuel.
• Engine oil level •Check the coolant level.
• UNI-TRAK® lever rod nut torque
Maintenance After Riding on a Dusty Course -
• UNI-TRAK® lever nut torque
If dirt or dust gets into the engine, cylinder, piston
• Rear shock absorber nut torque
and crankshaft bearings will be damaged. After rid-
• Swingarm pivot shaft nut torque
ing, inspect the crankshaft big end. If the crankshaft
• Rear axle nut torque
big end is worn past the service limit, replace the
• Rear sprocket nut torque
crankshaft with a new one.
• Rear brake pedal operation
• Seat installation Maintenance After Riding in the Rain or on a
• Front and rear wheel spoke torque Muddy Course -
• Front and rear tire air pressure •Apply grease to swingarm and rear suspension
• Front fork air pressure pivots.
• Drive chain slack •Inspect the drive chain and rear sprocket for wear.
• Coolant level •Clean the air cleaner element.
• Oil applied to air cleaner element •Check the cylinder and crankshaft big end.

PRE-RACE CHECKS AND AFTER-RACE MAINTENANCE 181
• Grease the throttle grip and control cables. • Rear shock absorber springs (for suspension ad-
justment)
Suggested Spare Parts -
• Front and rear wheels • Rear
clips
and engine sprockets with bolts/nuts and cir-
• Brake lever,and
Shift pedal brake pedal
• Electrical parts
• Throttle and clutch lever,
clutch and holders
• Spark plugs
• Handlebar cables
• Clutch assembly and friction plates
• Front and rear fenders, side covers, and number • Front and rear tires (various compounds and tread
Gaskets
• plate • patterns for different conditions)
• Radiator, radiator shroud, and water hoses
• Front fork assembly
• Air cleaner element
Throttle grip assembly
• Piston and piston rings
• Muffler, and related parts • snap rings, wire,
Tire wraps, bolts, nuts, screws, O-rings, washers,
• Chain case adhesive tape, vinyl tape (or duct
• Front fork springs (for suspension adjustment) tape), and #400 to #600 emery cloth
•

182 STORAGE
STORAGE
WARNING
Before Storage Gasoline is extremely flammable and can be
explosive under certain conditions, creating
When the motorcycle is to be stored for any length the potential for serious burns. Always stop
of time, it should be prepared for storage as follows. the engine and never smoke while handling
• Clean the entire vehicle thoroughly. fuel. Make sure the area is well-ventilated
• Run the engine for about five minutes to warm the
oil, then stop it and drain the engine oil.
and free from any source of flame or sparks;
this includes any appliance with a pilot light.
Make sure the engine is cold before working.
j WARNING Wipe any fuel off the engine before starting
Motor oil is a toxic substance. Dispose of it. Gasoline is a toxic substance. Dispose of
used oil properly. Contact your local author- gasoline properly. Contact your local author-
ities for approved disposal methods or pos- ities for approved disposal methods.
sible recycling.
• Remove the spark plug and spray fogging oil di-
• Install the oil drain bolt and fill in fresh engine oil. rectly into the cylinder. Kick the engine over slowly
• Empty the fuel tank (Fuel will deteriorate if left for
a long time.).
a few times to coat the cylinder wall. Install the
spark plug.
• Lubricate the drive chain and all the cables.
• Spray oil on all unpainted metal surfaces to pre-
vent rusting. Avoid getting oil on rubber parts and
on the brakes.
• Lift the motorcycle on a box or stand so that both
wheels are raised off the ground (If this cannot be
done, put boards under the front and rear wheels
to keep dampness away from the tire rubber.).
• Tie a plastic bag over the muffler to prevent mois-
ture from entering.
• Cover the motorcycle to keep dust and dirt away
from it.

STORAGE 183
• Fill the fuel tank with fuel.

After Storage • Checksallsection.
Check the points listed in the Daily Pre-Ride
• Remove the plastic bag from the muffler. • Perform a lubrication procedure in the Lubrication
• Make sure the spark plug is tight. section.
NOTE
Fit the plug cap securely onto the spark plug, and
pull the cap lightly to make sure that it is properly
installed.

184 ENVIRONMENTAL PROTECTION
ENVIRONMENTAL PROTECTION
Kawasaki subscribes to the guidelines of Tread Lightly! a program dedicated to protecting the great outdoors
through education and fostering responsible enjoyment of public lands. When using your Kawasaki motorcycle,
please follow these Tread Lightly! guidelines:
Tread Lightly!
Travel responsibly on designated roads and trails or in permitted areas.
Respect the rights of others including private property owners and all recreational trail users, campers and
others to allow them to enjoy their recreational activities undisturbed.
Educate yourself by obtaining travel maps and regulations from public agencies, planning for your trip, taking
recreation skills classes, and knowing how to use and operate your equipment safely.
A void sensitive areas such as meadows, lakeshores, wetlands and streams, unless on designated routes.
This protects wildlife habitat and sensitive soils from damage.
D o your part by leaving the area better than you found it, properly disposing of waste, minimizing the use of
fire, avoiding the spread of invasive species, restoring degraded areas, and joining a local enthusiast organi-
zation.
Properly discard used tires, engine oil, other vehicle components, or the entire vehicle that you might dispose
of in the future. Consult your authorized Kawasaki dealer or local environmental waste agency for their proper
disposal procedure.

WIRING DIAGRAM 185
WIRING DIAGRAM


2012 KX250F Owners Manual

Uploaded by

Copyright:

Available Formats

2012 KX250F Owners Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2012 KX250F Owners Manual

Uploaded by

Copyright:

Available Formats

Downloaded from www.Manualslib.

com manuals search engine

A Table of Contents is included after the

Downloaded from www.Manualslib.com manuals search engine

• This vehicle is designed for the operator only, no passengers.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

KAWASAKI HEAVY INDUSTRIES, LTD.

© 2011 Kawasaki Heavy Industries, Ltd. Apr. 2011. (1)

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Specifications are subject to change without notice.

Downloaded from www.Manualslib.com manuals search engine

1. Clutch Lever 3. Fuel Tank Cap 5. Front Brake Lever

Downloaded from www.Manualslib.com manuals search engine

1. Front Fork 6. Upstream Injector 11. Shift Pedal

Downloaded from www.Manualslib.com manuals search engine

1. Muffler 5. Uni-Trak® Tie-Rod and Rocker Arm

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

• Shift the transmission into neutral.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Break in the engine as follows.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

After racing, first clean the motorcycle, then in-

Downloaded from www.Manualslib.com manuals search engine

MAINTENANCE AND ADJUSTMENT

Downloaded from www.Manualslib.com manuals search engine

FREQUENCY After each Every 3 Every 6 Every 12

Downloaded from www.Manualslib.com manuals search engine

2. Periodic Inspection (Chassis Related Item)

Drive chain - inspect and adjust • 82

Downloaded from www.Manualslib.com manuals search engine

FREQUENCY After each Every 3 Every 6 Every 12

Swingarm and UNI-TRAK linkage

Downloaded from www.Manualslib.com manuals search engine

3. Periodic Replacement (Engine and Chassis Related Item)

†: Replace, add, adjust, clean or torque if necessary.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

NOTE • Warm up the engine thoroughly so that the oil will

A. Oil Level Gauge WARNING

Downloaded from www.Manualslib.com manuals search engine

A. Oil Filter Cover

A. Oil Filter Element

Downloaded from www.Manualslib.com manuals search engine

• Install the spring to the oil filter cover. Tightening Torque

Downloaded from www.Manualslib.com manuals search engine

• Tighten the oil filler plug.