TM 55-1520-210-23-3

Download as pdf or txt
Download as pdf or txt
You are on page 1of 762

TM 55-1520-210-23-3

TECHNICAL MANUAL

AVIATION UNIT AND INTERMEDIATE


MAINTENANCE INSTRUCTIONS
ARMY MODEL UH-1H/V/EH-1H/X

This manual supersedes TM 55-1520-210-23-3, 20 February 1979, including all changes.

HEADQUARTERS, DEPARTMENT OF THE ARMY


30 SEPTEMBER 1987
TM 55-1520--210--23--3
C9

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 9 WASHINGTON, D.C., 21 April 2003

Aviation Unit and Intermediate


Maintenance Instructions
ARMY MODEL UH--1H/V/EH--1H/X HELICOPTERS

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

TM 55-1520-210--23--3, 30 September 1987, is changed as follows:


1. Remove and insert pages as indicated below. New or changed text material is indicated by a vertical bar in the
margin. An illustration change is indicated by a miniature pointing hand.

Remove pages Insert pages


a and b a and b
---------- A through C/(D blank)
A--1 and A--2 A--1 and A--2
C--7 and C--8 C--7 and C--8
D--1 and D--2 D--1 and D--2
D--9 and D--10 D--9 and D--10
D--62.1 and D--62.2 D--62.1 and D--62.2
D--65 through D--68 D--65 through D--68
D--89 and D--90 D--89 and D--90
D--195 and D--196 D--195 and D--196
D--247 and D--248 D--247 and D--248
D--283 and D--284 D--283 and D--284
D--397 and D--398 D--397 and D--398
E--3 and E--4 E--3 and E--4
F--39 and F--40 F--39 and F--40
2. Retain this sheet in front of manual for reference purposes.
TM 55-1520-210-23-3
C9

By Order of the Secretary of the Army:

Official:

ERIC K. SHINSEKI
General, United States Army
Chief of Staff

JOEL B. HUDSON
Administrative Assistant to the
Secretary of the Army
0307103

DISTRIBUTION:
To be distributed in accordance with Initial Distribution Number (IDN) 311408, requirements for
TM 55-1520-210-23-3.
TM 55-1520-210-23-3
C8

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 8 WASHINGTON, D.C., 14 June 1996

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-IHNIEH-IHIX HELICOPTERS

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. Remove and insert pages as indicated below. New or changed text material is indicated by a vertical bar in the
margin. An illustration change is indicated by a miniature pointing hand.

Remove pages Insert pages

i and ii i and ii
A-1 through A-3/(A-4 blank) A-1 through A-3/(A-4 blank)
B-9 and B-10 B-9 and B-10
B-55 through B-58 B-55 through B-58
C-1 through C-10 C-1 through C-10
D-3 and D-4 D-3 and D-4
D-53 and D-54 D-53 and D-54
D-68.1 and D-68.2 D-68.1 and D-68.2
D-69 and D-70 D-69 and D-70
D-73 and D-74 D-73 and D-74
D-79 and D-80 D-79 and D-80
D-85 and D-86 D-85/(D-86 blank)
D-90.3/(D-90.4 blank) D-90.3/(D-90.4 blank)
D-115 and D-116 D-115 and D-116
D-199 and D-200 D-199 and D-200
D-389 and D-390 D-389 and D-390
___________ D-445/(D-446 blank)
F-1 and F-2 F-1 and F-2
___________ F-76.1/(F-76.2 blank)
F-77 and F-78 F-77 and F-78
Index 5 and Index 6 Index 5 and Index 6
Index 9 and Index 10 Index 9 and Index 10
TM 55-1520-210-23-3
C7

CHANGE HEADQUARTER
DEPARTMENT OF THE ARMY
NO. 7 WASHINGTON, D.C., 31 July 1995

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X


HELlCOPTERS

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. Remove and insert pages as indicated below. New or changed text material is indicated by a vertical bar
in the margin. An illustration change is indicated by a miniature pointing hand.

Remove pages Insert pages

Index 5 and Index 6 Index 5 and Index 6

2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

DENNIS J. REIMER
General, United States Army
Chief of Staff

Acting Administrative Assistant to the


Secretary of the Army
00485

DISTRIBUTION:
To be distributed in accordance with DA Form 12-31-E, block no. 1408, requirements for
TM 55-1520-210-23-3.
URGENT TM 55–1520-210-23-3
C 6

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 6 WASHINGTON, D.C., 31 May 1994

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. Remove and insert pages as indicated below. New or changed text material is
indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

E-3 and E-4 E-3 and E-4


E-5 and E-6 E-5 and E-6
F-82.1/(F-82.2 blank) F-82.1/(F-82.2 blank)

2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
06213

DISTRIBUTION :
To be distributed in accordance with DA Form 12-31-E, block no. 1408, require-
ments for TM 55-1520-210-23-3.
TM 55-1520-210-23-3
C 5

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 5 WASHINGTON, D.C., 15 OCTOBER 1993

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. To correct change 4 remove and insert page, disregard inserting page


D-396.1/D-396.2. This page does not exist.

2. Remove and insert pages as indicated below. New or changed text material is
indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

i and ii i and ii
A-1 through A-3/ A-1 through A–3/
(A-4 blank) (A-4 blank)
B-19 and B-20 B-19 and B-20
B-63 and B-64 B-63 and B-64
B-79 through B-82 B–79 through B–82
C-1 and C-2 C-1 and C-2
D-1 through D–4 D–1 through D-4
D-5 and D-6 D-5 and D-6
D-9 through D-14 D-9 through D-14
D-62.1 and D-62.2 D-62.1 and D-62.2
D-67 and D-68 D-67 and D-68
D-68.1 and D-68.2 D-68.1 and D-6812
D-69 and D-70 D-69 and D–70
D-90.3/(D-90.4 blank) D-90.3/(D-90.4 blank)
D-127 and D-128 D-127 and D-128
D-183 and D-184 D-183 and D-184
D-373 and D-374 D-373 and D-374
D-405 and D-406 D-405 and D-406
D-433 and D-434 D-433 and D-434
D-441 through D-443/ D-441 through D-444
(D-444 blank)
F-93/(F-94 blank) F-93/(F–94 blank)
Index 5 and Index 6 Index 5 and Index 6

3. Retain this sheet in manual for reference purposes.


TM 55-1520-210-23-3
C 5

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
05619

DISTRIBUTION:
To be distributed in accordance with DA Form 12–31-E, block no. 1408, require-
ments for TM 55-1520–210-23–3.
TM 55-1520-210-23-3
C 4

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 4 WASHINGTON, D.C., 30 SEPTEMBER 1991

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X Helicopters

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. Remove and insert pages as indicated below. New or changed text material
is indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

A-1 through A-3/A-4 A-1 through A-3/A-4


B-3 and B-4 B-3 and B-4
B-17 through B-20 B-17 through B-20
B-23 and B-24 B-23 and B-24
B-27 and B-28 B-27 and B-28
B-29 and B-30 B-29 and B-30
B-55 and B-56 B-55 and B-56
B-69 and B-70 B-69 and B-70
B-70.1 through B-70.8 - - -
B-77 and B-78 B-77 and B-78
C-1 through C-6 C-1 through C-10
D-1 through D-4 D-1 through D-4
D-5 and D-6 D-5 and D-6
- - — D-6.1/D-6.2
D-9 through D-14 D-9 through D-14
D-67 and D-68 D-67 and D-68
D-68.1 and D-68.2 D-68.1 and D-68.2
D-69 and D-70 D-69 and D-70
D-73 through D-90 D-73 through D-90
D-90.1 and D-90.2 D-90.1 through D-90.3/D-90.4
D-175 and D-176 D-175 and D-176
D-183 and D-184 D-183 and D-184
D-213 and D-214 D-213 and D-214
D-247 and D-248 D-247 and D-248
D-339 and D-340 D-339 and D-340
D-373 and D-374 D-373 and D-374
D-379 and D-380 D-379 and D-380
D-389 and D-390 D-389 and D-390
- - - D-396.1/D-396.2
D-397 and D-398 D-397 and D-398
D-429/D-430 D-429 through D-441/D-442
E-3 and E-4 E-3 and E-4
E-7 through E-10 E-7 through E-10
E-11 and E-12 E-11 and E-12
F-23 and F-24 F-23 and F-24
TM 55-1520-210-23-3
C 4
Remove pages Insert pages

F-51 and F-52 F-51 and F-52


F-75/F-76 F-75/F-76
- - - F-82.1/F-82.2
F-99/F-100 F-99/F-100
F-113 and F-114 F-113 and F-114
Index 1 through Index 13 Index 1 through Index 14
2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

GORDON R. SULLIVAN
General, United States Army
Official: Chief of Staff

PATRICIA P. HICKERSON
Colonel, United States Army
The Adjutant General

DISTRIBUTION:
To be distributed in accordance with DA Form 12-31-E, block no., 1408, AVUM
and AVIM maintenance requirements for TM 55-1520-210-23-3.
TM 55-1520-210-23-3

URGENT C3

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 3 WASHINGTON, D.C., 30 March 1990

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X Helicopters

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1.Remove and insert pages as indicated below. New or changed text material
is indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

D-1 and D-2 D-1 and D-2


—--— D-429/D-430
E-1 through E-4 E-1 through E-4

2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

CARL E. VUONO
General, United States Army
Official: Chief of Staff

WILLIAM J. MEEHAN II
Brigadier General, United States Army
The Adjutant General

DISTRIBUTION:
To be distributed in accordance with DA Form 12-31, AVUM and AVIM Maintenance
requirements for UH-1H/V Helicopter, Utility, EH-1H Helicopter, Electronic
Countermeasure and EH-1X Helicopter, Electronic Countermeasure & Intercept.

URGENT
URGENT TM 55-1520-210-23-3
C 2

CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 2 WASHINGTON, D.C., 24 August 1989

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X HELICOPTERS

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:

1. Remove and insert pages as indicated below. New or changed text material
is indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

B-3 and B-4 B-3 and B-4


B-17 and B-18 B-17 and B-18
B-22.1/B-22.2 ----
B-23 and B-24 B-23 and B-24
B-27 and B-28 B-27 and B-28
---- B-28.1/B-28.2

2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

CARL E. VUONO
General, United States Army
Official: Chief of Staff

WILLIAM J. MEEHAN II
Brigadier General, United States Army
The Adjutant General

DISTRIBUTION :
To be distributed in accordance with DA Form 12-31, AVUM and AVIM Maintenance
requirements for UH-1H/V Helicopter, Utility, EH-1H Helicopter, Electronic
Countermeasure and EH-1X Helicopter, Electronic Countermeasure & Intercept.

URGENT
URGENT
TM 55-1520-210-23-3
C 1

HEADQUARTERS
CHANGE DEPARTMENT OF THE ARMY
WASHINGTON, D.C., 8 November 1988
NO. 1
Aviation Unit and Intermediate
Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X HELICOPTERS

TM 55-1520-210-23-3, 30 September 1987, is changed as follows:


1. Remove and insert pages as indicated below. New or changed text material
is indicated by a vertical bar in the margin. An illustration change is indicated
by a miniature pointing hand.

Remove pages Insert pages

B-3 and B-4 B-3 and B-4


- - - B-22.1/B-22.2
B-23 and B-24
B-23 and B-24
D-1 through D-4 D-1 through D-4
D-171 and D-172 D-171 and D-172
D-427 and D-428
D-427

2. Retain this sheet in front of manual for reference purposes.

By Order of the Secretary of the Army:

CARL E. VUONO,
General, United States Army
Chief of Staff
Official:

WILLIAM J. MEEHAN II
Brigadier General, United States Army
The Adjutant General

DISTRIBUTION :
To be distribution in accordance with DA Form 12-31, AVUM and AVIM requirements
for UH-1H/V Helicopter, Utility, EH-1H, Helicopter, Electronic Countermeasure and
EH-1X Helicopter, Electronic Countermeasure & Intercept.

URGENT
TM 55-1520-210-23-3

TECHNICAL MANUAL HEADQUARTERS


DEPARTMENT OF THE ARMY
No. 55-1520-210-23-3 WASHINGTON9 D.C., 3O September 1987.

Aviation Unit and Intermediate


Maintenance Instructions

ARMY MODEL UH-1H/V/EH-1H/X HELICOPTERS

NOTE :

This manual is printed in three volumes as follows:

TM 55-1520-210-23-1, consisting of Table of Contents, preface, Chapters 1


through 6.

TM 55-1520-210-23-2, consisting of Table of Contents, Chapters 7 through 17.

TM 55-1520-210-23-3, consisting of Table of Contents, Appendix A through F,


and Index.

The Appendices and Index are applicable to all volumes.


WARNING PAGE TM 55-1520-210-23-3

Personnel performing operations, procedures,


and practices which are included or implied in this
technical manual shall observe the following warnings.
Disregard of these warnings and precautionary
information can cause serious injury, or death.

Warnings, cautions, and notes are used to emphasize


important and critical instructions and are used for
the following conditions:

An operating procedure, practice, etc., which,


if not correctly followed, could result in personal
injury or loss of life.

An operating procedure, practice, etc., which, if not


strictly observed, could result in damage to or destruction
of equipment.

NOTE

An operating procedure, condition, etc., which


it is essential to highlight.

NOISE

Sound pressure levels in this helicopter during some operating conditions exceed the Surgeon General hearing
conservation criteria, as defined in TB MED 251. Hearing protection devices, such as aviator helmet or ear plugs
are required to be worn by all personnel in and around the helicopter during its operation.

ELECTROLYTE

Corrosive Battery Electrolyte (Potassium Hydroxide). Wear rubber gloves, apron, and face shield when handling
leaking batteries. If potassium hydroxide is spilled on clothing, or other material wash immediately with clean
water. If spilled on personnel, immediately start flushing the affected area with clean water. Continue washing
until medical assistance arrives.

TOXIC POISONS

Turbine fuels and lubricating oils contain additives which are poisonous and readily absorbed through the skin.
Do not allow them to remain on skin longer than necessary.

STARTING HELICOPTER

Starting and operation of the helicopter will be performed only by authorized personnel in accordance with AR95-
1.

a
TM 55-1520-210-23-3 WARNING PAGE

GROUNDING HELICOPTER
The helicopter should be electrically grounded when parked. Turn off all power switches before making electrical
connections or disconnections. Serious burns and electrical shock can result from contact with exposed electrical
wires or connectors.
Before removing any engine ignition system component, ground the leads to dissipate any stored voltage in ignition
unit.

FIRE EXTINGUISHER
Exposure to high concentrations of fire extinguishing agent or decomposition products should be avoided. The
liquid should not be allowed to come into contact with the skin, as it may cause frost bite or low temperature burns.

ARMAMENT
Loaded weapons, or weapons being loaded or unloaded, shall be pointed in a direction which offers the least
exposure to personnel or property in the event of accidental firing. Personnel shall remain clear of hazardous area
of all loaded weapons.
ANY ROTATION OF THE GUN ARMAMENT SUBSYSTEM BARRELS WILL CAUSE THE GUN TO FIRE. Upon
landing, immediately alert personnel to probable presence of live rounds in the gun. Summon armament repairman
to clear weapon.

FUELING AND DEFUELING


When refueling helicopter, the refueling vehicle or forward air refueling unit must be parked a minimum of 20 feet
from the helicopter. Before starting the fueling operation, always insert fueling nozzle grounding chain of fuel truck
ground wire into GROUND HERE receptacle located on the right side of the helicopter aft of the cabin area. Refer
to TM 10-1101.
When defueling, turn off all electrical switches and disconnect external power from the helicopter. The helicopter
must be electrically grounded prior to defueling.

RADIOACTIVE MATERIALS
Self-luminous dials and ignition units may contain radioactive materials. If such an instrument or unit is broken or
becomes unsealed, avoid personal contact. Use forceps or gloves made of rubber or polyethylene to pick up
contaminated material. Place materials and gloves in a plastic bag. Seal bag and dispose of it as radioactive waste
in accordance with AR755-15 and TM 3-261 (Refer to 55-1500-314-25). Repair procedures shall conform to re-
quirements in AR700-52.

CLEANING SOLVENTS
Cleaning solvents may be flamable and toxic. Use only in well ventilated areas. Avoid inhalation of vapor and skin
contact. Do not use solvents near open flame or in areas where very high temperatures prevail. Solvents with a
flash point greater than 100°F (38°C) should be used unless otherwise specified.

ROTOR BLADES
Personnel will stay clear of rotor blades during operation. Refer to Chapter 1 for rotor blade dimensions and clear-
ances.

b Change 9
TM 55-1520-210-23-3

LIST OF EFFECTIVE PAGES


Insert latest changed pages; dispose of superseded pages in accordance with regulations.

NOTE: On a changed page, the portion of the text affected by the latest change is indicated by a vertical line, or other
change symbol, in the outer margin of the page. Changes to illustrations are indicated by miniature pointing hands.
Changes to wiring diagrams are indicated by shaded areas.

Dates of issue for original and changed pages are:


Original . . . . . 0 ....... 30 September 1987 Change . . . . . 5 ....... 15 October 1993
Change . . . . . 1 ....... 8 November 1988 Change . . . . . 6 ....... 31 May 1994
Change . . . . . 2 ....... 24 August 1989 Change . . . . . 7 ....... 31 July 1995
Change . . . . . 3 ....... 30 March 1990 Change . . . . . 8 ....... 14 June 1996
Change . . . . . 4 ....... 30 September1991 Change . . . . . 9 ....... 21 April 2003

Page *Change Page *Change


No. No. No. No.
Cover . . . . . . . . . . . . . . . . . 0 B-56 -- B-57 . . . . . . . . . . . . 8
a ..................... 0 B-58 -- B-62 . . . . . . . . . . . . 0
b ..................... 9 B-63 . . . . . . . . . . . . . . . . . . 5
A -- B . . . . . . . . . . . . . . . . . . 9 B-64 -- B-69 . . . . . . . . . . . . 0
i ...................... 8 B-70 . . . . . . . . . . . . . . . . . . 4
ii -- iii . . . . . . . . . . . . . . . . . . 0 B-71 -- B-76 . . . . . . . . . . . . 0
iv blank . . . . . . . . . . . . . . . . 0 B-77 . . . . . . . . . . . . . . . . . . 4
A-1 . . . . . . . . . . . . . . . . . . . 8 B-78 -- B-79 . . . . . . . . . . . . 0
A-2 . . . . . . . . . . . . . . . . . . . 9 B-80 -- B-82 . . . . . . . . . . . . 5
A-3 . . . . . . . . . . . . . . . . . . . 8 B-83 -- B-85 . . . . . . . . . . . . 0
A-4 blank . . . . . . . . . . . . . . 0 C-1 . . . . . . . . . . . . . . . . . . . 4
B-1 -- B-2 . . . . . . . . . . . . . . 0 C-2 -- C-7 . . . . . . . . . . . . . . 8
B-3 . . . . . . . . . . . . . . . . . . . 4 C-8 . . . . . . . . . . . . . . . . . . . 9
B-4 . . . . . . . . . . . . . . . . . . . 1 C-9 -- C-10 . . . . . . . . . . . . . 8
B-5 -- B-9 . . . . . . . . . . . . . . 0 D-1 . . . . . . . . . . . . . . . . . . . 0
B-10 . . . . . . . . . . . . . . . . . . 8 D-2 . . . . . . . . . . . . . . . . . . . 9
B-10.1 . . . . . . . . . . . . . . . . . 0 D-3 . . . . . . . . . . . . . . . . . . . 8
B-10.2 blank . . . . . . . . . . . 0 D-4 . . . . . . . . . . . . . . . . . . . 5
B-11 -- B-16 . . . . . . . . . . . . 0 D-4.1 . . . . . . . . . . . . . . . . . . 0
B-17 . . . . . . . . . . . . . . . . . . 4 D-4.2 blank . . . . . . . . . . . . 0
B-18 . . . . . . . . . . . . . . . . . . 0 D-5 . . . . . . . . . . . . . . . . . . . 4
B-19 . . . . . . . . . . . . . . . . . . 5 D-6 . . . . . . . . . . . . . . . . . . . 5
B-20 -- B-22 . . . . . . . . . . . . 0 D-6.1 . . . . . . . . . . . . . . . . . . 4
B-23 . . . . . . . . . . . . . . . . . . 2 D-6.2 blank . . . . . . . . . . . . 4
B-24 . . . . . . . . . . . . . . . . . . 4 D-7 -- D-8 . . . . . . . . . . . . . . 0
B-25 -- B-27 . . . . . . . . . . . . 0 D-9 . . . . . . . . . . . . . . . . . . . 9
B-28 . . . . . . . . . . . . . . . . . . 4 D-10 -- D-11 . . . . . . . . . . . . 0
B-28.1 . . . . . . . . . . . . . . . . . 2 D-12 -- D-14 . . . . . . . . . . . . 5
B-28.2 blank . . . . . . . . . . . 2 D-15 -- D-52 . . . . . . . . . . . . 0
B-29 . . . . . . . . . . . . . . . . . . 0 D-53 . . . . . . . . . . . . . . . . . . 8
B-30 . . . . . . . . . . . . . . . . . . 4 D-54 -- D-62 . . . . . . . . . . . . 0
B-31 -- B-50 . . . . . . . . . . . . 0 D-62.1 . . . . . . . . . . . . . . . . 9
B-50.1 . . . . . . . . . . . . . . . . . 0 D-62.2 . . . . . . . . . . . . . . . . 5
B-50.2 blank . . . . . . . . . . . 0 D--62.3 . . . . . . . . . . . . . . . . 0
B-51 -- B--55 . . . . . . . . . . . 0 D-62.4 blank . . . . . . . . . . . 0
*Zero in this column indicates an original page.

Change 9 A
TM 55-1520-210-23-3

LIST OF EFFECTIVE PAGES (CON’T)


Page *Change Page *Change
No. No. No. No.
D-63 D-65 . . . . . . . . . . . . . 0 D-398 -- D--405 . . . . . . . . . 0
D-66 . . . . . . . . . . . . . . . . . . 9 D-406 . . . . . . . . . . . . . . . . . 5
D-67 . . . . . . . . . . . . . . . . . . 5 D-407 -- D--427 . . . . . . . . . 0
D-68 . . . . . . . . . . . . . . . . . . 9 D-428 . . . . . . . . . . . . . . . . . 1
D-68.1 -- D-68.2 . . . . . . . . 8 D-429 . . . . . . . . . . . . . . . . . 3
D-69 . . . . . . . . . . . . . . . . . . 5 D-430 -- D-432 . . . . . . . . . 4
D-70 . . . . . . . . . . . . . . . . . . 8 D-433 . . . . . . . . . . . . . . . . . 5
D-71 -- D-73 . . . . . . . . . . . . 0 D-434 -- D-440 . . . . . . . . . 4
D-74 . . . . . . . . . . . . . . . . . . 8 D-441 . . . . . . . . . . . . . . . . . 5
D-75 -- D-78 . . . . . . . . . . . . 4 D-442 . . . . . . . . . . . . . . . . . 4
D-79 D-80 . . . . . . . . . . . . . 8 D-443 -- D--444 . . . . . . . . . 5
D-81 -- D-84 . . . . . . . . . . . . 4 D-445 . . . . . . . . . . . . . . . . . 8
D-85 . . . . . . . . . . . . . . . . . . 8 D-446 blank . . . . . . . . . . . . 8
D-86 blank . . . . . . . . . . . . . 8 E-1 -- E-2 . . . . . . . . . . . . . . 3
D-87 -- D-89 . . . . . . . . . . . . 4 E-2.1 . . . . . . . . . . . . . . . . . . 0
D-90 . . . . . . . . . . . . . . . . . . 9 E-2.2 blank . . . . . . . . . . . . 0
D-90.1 -- D-90.2 . . . . . . . . 4 E-3 . . . . . . . . . . . . . . . . . . . 9
D-90.3 . . . . . . . . . . . . . . . . 8 E-4 . . . . . . . . . . . . . . . . . . . 6
D-90.4 blank . . . . . . . . . . . 4 E-4.1 . . . . . . . . . . . . . . . . . . 0
D-91 -- D-115 . . . . . . . . . . . 0 E-4.2 . . . . . . . . . . . . . . . . . . 0
D-116 . . . . . . . . . . . . . . . . . 8 E-5 . . . . . . . . . . . . . . . . . . . 0
D-117 -- D-127 . . . . . . . . . 0 E-6 . . . . . . . . . . . . . . . . . . . 6
D-128 . . . . . . . . . . . . . . . . . 5 E-7 . . . . . . . . . . . . . . . . . . . 4
D-129 -- D-170 . . . . . . . . . 0 E-8 . . . . . . . . . . . . . . . . . . . 0
D-171 . . . . . . . . . . . . . . . . . 1 E-9 . . . . . . . . . . . . . . . . . . . 4
D-172 -- D-174 . . . . . . . . . 0 E-10 . . . . . . . . . . . . . . . . . . 0
D-175 . . . . . . . . . . . . . . . . . 4 E-10.1 . . . . . . . . . . . . . . . . . 0
D-176 -- D-182 . . . . . . . . . 0 E-10.2 . . . . . . . . . . . . . . . . . 0
D-183 -- D-184 . . . . . . . . . 5 E-11 -- E-12 . . . . . . . . . . . . 4
D-185 -- D-195 . . . . . . . . . 0 F-1 . . . . . . . . . . . . . . . . . . . 0
D-196 . . . . . . . . . . . . . . . . . 9 F-2 . . . . . . . . . . . . . . . . . . . 8
D-197 -- D-199 . . . . . . . . . 0 F-3 -- F-20 . . . . . . . . . . . . . 0
D-200 . . . . . . . . . . . . . . . . . 8 F-20.1 . . . . . . . . . . . . . . . . . 0
D-201 -- D-212 . . . . . . . . . 0 F-20.2 blank . . . . . . . . . . . 0
D-213 . . . . . . . . . . . . . . . . . 4 F-21 -- F-24 . . . . . . . . . . . . 0
D-214 -- D-247 . . . . . . . . . 0 F--24.1 . . . . . . . . . . . . . . . . 0
D-248 . . . . . . . . . . . . . . . . . 9 F-24.2 blank . . . . . . . . . . . 0
D-249 -- D-261 . . . . . . . . . 0 F-25 -- F-29 . . . . . . . . . . . . 0
D--261.1 . . . . . . . . . . . . . . . 0 F-30 blank . . . . . . . . . . . . . 0
D-262 -- D-283 . . . . . . . . . 0 F-31 . . . . . . . . . . . . . . . . . . 0
D-284 . . . . . . . . . . . . . . . . . 9 F-32 blank . . . . . . . . . . . . . 0
D-285 -- D-378 . . . . . . . . . 0 F-33 . . . . . . . . . . . . . . . . . . 0
D-379 . . . . . . . . . . . . . . . . . 4 F-34 blank . . . . . . . . . . . . . 0
D-380 -- D-389 . . . . . . . . . 0 F-35 . . . . . . . . . . . . . . . . . . 0
D-390 . . . . . . . . . . . . . . . . . 8 F-36 blank . . . . . . . . . . . . . 0
D-391 -- D-396 . . . . . . . . . 0 F-37 . . . . . . . . . . . . . . . . . . 0
D--397 . . . . . . . . . . . . . . . . . 9 F-38 blank . . . . . . . . . . . . . 0

*Zero in this column indicates an original page.


B Change 9
TM 55-1520-210-23-3

LIST OF EFFECTIVE PAGES (CON’T)


Page *Change Page *Change
No. No. No. No.
F-39 . . . . . . . . . . . . . . . . . . 9 F--97 -- F--98 . . . . . . . . . . . 0
F-40 . . . . . . . . . . . . . . . . . . 0 F--99 . . . . . . . . . . . . . . . . . . 4
F-41 . . . . . . . . . . . . . . . . . . 0 F--100 blank . . . . . . . . . . . . 0
F-42 blank . . . . . . . . . . . . . 0 F--101 . . . . . . . . . . . . . . . . . 0
F-43 -- F-50 . . . . . . . . . . . . 0 F--102 blank . . . . . . . . . . . . 0
F-51 . . . . . . . . . . . . . . . . . . 4 F--103 -- F--104 . . . . . . . . . 0
F-52 -- 5-53 . . . . . . . . . . . . 0 F--105 . . . . . . . . . . . . . . . . . 0
F-55 . . . . . . . . . . . . . . . . . . 0 F--106 blank . . . . . . . . . . . . 0
F-56 blank . . . . . . . . . . . . . 0 F--107 . . . . . . . . . . . . . . . . . 0
F--57 . . . . . . . . . . . . . . . . . . 0 F--108 blank . . . . . . . . . . . . 0
F--58 blank . . . . . . . . . . . . . 0 F--109 . . . . . . . . . . . . . . . . . 0
F--59 . . . . . . . . . . . . . . . . . . 0 F--110 blank . . . . . . . . . . . . 0
F--60 blank . . . . . . . . . . . . . 0 F--111 . . . . . . . . . . . . . . . . . 0
F--61 . . . . . . . . . . . . . . . . . . 0 F--112 blank . . . . . . . . . . . . 0
F--62 blank . . . . . . . . . . . . . 0 F--113 . . . . . . . . . . . . . . . . . 0
F--63 . . . . . . . . . . . . . . . . . . 0 F--114 . . . . . . . . . . . . . . . . . 4
F--64 blank . . . . . . . . . . . . . 0 F--115 . . . . . . . . . . . . . . . . . 0
F--65 . . . . . . . . . . . . . . . . . . 0 F--116 blank . . . . . . . . . . . . 0
F--66 blank . . . . . . . . . . . . . 0 F--117 . . . . . . . . . . . . . . . . . 0
F--67 -- F--74 . . . . . . . . . . . 0 F--118 blank . . . . . . . . . . . . 0
F--75 . . . . . . . . . . . . . . . . . . 4 F--119 . . . . . . . . . . . . . . . . . 0
F--76 blank . . . . . . . . . . . . . 0 F--120 blank . . . . . . . . . . . . 0
F--76.1 . . . . . . . . . . . . . . . . 8 F--121 . . . . . . . . . . . . . . . . . 0
F--76.2 blank . . . . . . . . . . . 8 F--122 blank . . . . . . . . . . . . 0
F--77 -- F--78 . . . . . . . . . . . 0 F--123 . . . . . . . . . . . . . . . . . 0
F--79 . . . . . . . . . . . . . . . . . . 0 F--124 blank . . . . . . . . . . . . 0
F--80 blank . . . . . . . . . . . . . 0 F--125 . . . . . . . . . . . . . . . . . 0
F--81 . . . . . . . . . . . . . . . . . . 0 F--126 blank . . . . . . . . . . . . 0
F--82 blank . . . . . . . . . . . . . 0 F--127 . . . . . . . . . . . . . . . . . 0
F--82.1 . . . . . . . . . . . . . . . . 6 F--128 blank . . . . . . . . . . . . 0
F--82.2 blank . . . . . . . . . . . 4 F--129 . . . . . . . . . . . . . . . . . 0
F--83 blank . . . . . . . . . . . . . 0 F--130 blank . . . . . . . . . . . . 0
F--84 blank . . . . . . . . . . . . . 0 F--131 . . . . . . . . . . . . . . . . . 0
F--85 . . . . . . . . . . . . . . . . . . 0 F--132 blank . . . . . . . . . . . . 0
F--86 blank . . . . . . . . . . . . . 0 Index 1 -- Index 4 . . . . . . . 4
F--87 -- F--88 . . . . . . . . . . . 0 Index 5 . . . . . . . . . . . . . . . . 8
F--89 . . . . . . . . . . . . . . . . . . 0 Index 6 . . . . . . . . . . . . . . . . 5
F--90 blank . . . . . . . . . . . . . 0 Index 7 -- Index 8 . . . . . . . 4
F--91 . . . . . . . . . . . . . . . . . . 0 Index 8 . . . . . . . . . . . . . . . . 4
F--92 blank . . . . . . . . . . . . . 0 Index 9 . . . . . . . . . . . . . . . . 8
F--93 . . . . . . . . . . . . . . . . . . 0 Index 10 . . . . . . . . . . . . . . . 4
F--94 blank . . . . . . . . . . . . . 0 Index 11 -- Index 12 . . . . . 0
F--95 . . . . . . . . . . . . . . . . . . 0 Index 13 -- Index 14 . . . . . 4
F--96 blank . . . . . . . . . . . . . 0

*Zero in this column indicates an original page.

Change 9 C/(D blank)


TM 55-1520-210-23-3

TECHNICAL MANUAL HEADQUARTERS


DEPARTMENT OF THE ARMY
TM 55-1520-210-23-3 WASHINGTON, D.C., 30 September 1987

AVIATION AND INTERMEDIATE


MAINTENANCE INSTRUCTIONS
ARMY MODEL UH-1HNIEH-1HIX HELICOPTER

REPORTING OF ERRORS

You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let
us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 20282
located in the back of this manual directly to: Commander, U.S. Army Aviation and Troop Command, ATTN: AMSATIMP,
4300 Goodfellow Blvd., St. Louis, MO 631201798. A reply will be furnished to you. You may also submit your
recommended changes by Email directly to <mpmtP/[email protected]>. A reply will be furnished to you.
DISTRIBUTION STATEMENT A: Approved for public release; distribution Is unlimited.

TABLE OF CONTENTS

Page
CHAPTER 1 INTRODUCTION
Section I Servicing................................................................................................................................ 1-1
II Lubrication............................................................................................................................. 140
III Handling, Jacking, Mooring, Hoisting, and Sling Loading ..................................................... 1-54
IV Inspection Requirements ...................................................................................................... 146
V Overhaul and Retirement Schedule ...................................................................................... 1-110
VI Flight Safety Critical Aircraft Parts......................................................................................... 1-115

CHAPTER 2 AIRFRAME
Section I Fuselage................................................................................................................................ 2-1
II Tailboom................................................................................................................................ 2-193

CHAPTER 3 ALIGHTING GEAR


Section I Landing Gear......................................................................................................................... 3-1
II Skids/Struts ........................................................................................................................... 3-30
III Floats..................................................................................................................................... 3-30
IV Skis........................................................................................................................................ 3-30
V Brakes ................................................................................................................................... 3-30

CHAPTER 4 POWER PLANT


Section I Power Plant ........................................................................................................................... 4-1
II Cooling System ..................................................................................................................... 4-13
II Air Induction System ............................................................................................................. 4-13
IV Exhaust System .................................................................................................................... 4-42.7
V Oil System ............................................................................................................................. 4-44
VI Ignition System...................................................................................................................... 4-41
VII Power Controls...................................................................................................................... 4-61
VIII Quick Change Assembly (AVIM)........................................................................................... 4-86

Change 8 i
TM 55-1520-210-23-3

TABLE OF CONTENTS (Cont)

Page

CHAPTER 5. ROTORS
Section I. Main Rotor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
II. Main Rotor Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
III. Main Rotor Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38.1
IV. Main Rotor Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54.45
V. Tall Rotor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-105
VI. Tall Rotor Hub and Blade Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-107
VII. Tall Rotor Hub and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-119
VIII. Tall Rotor Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-132
IX. Tracking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-138

CHAPTER 6. DRIVE TRAIN SYSTEM


Section I. Main Driveshaft . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
II. Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29
III, Main Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . 6-29
IV. Tall Rotor Driveshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-116.2
V. intermediate Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-138
VI. Tall Rotor Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-147
VII. Oil Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-167

CHAPTER 7. HYDRAULIC AND PNEUMATIC SYSTEMS


Section I. Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 7-1
Il. Pneumatic System (Not Applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-51

CHAPTER 8. INSTRUMENT SYSTEMS


Section I. Instrument Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
II. Engine instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
III. Flight Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
IV. Navigation Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33
V. Miscellaneous Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-37
VI. Instrument Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-51

CHAPTER 9. ELECTRICAL SYSTEMS


Section I. Direct Current Power Distribution System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
II. Alternating Current Power Distribution System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-41
III. Starting System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-52
IV. Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-54
V. Lighting Provisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-56
VI. Miscellaneous Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-94

CHAPTER 10. FUEL SYSTEM


Section I. Fuel Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
II. Fuel Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

CHAPTER 11. FLIGHT CONTROLS


Section I. Controls Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
II. Flight Control Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

ii
TM 55-1520-210-23-3

TABLE OF CONTENTS (Cont)

CHAPTER 12 UTILITY SYSTEMS


Section I Fire Detector System . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
II Windshield Wiper System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
III Rear View Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-20

CHAPTER 13 ENVIRONMENTAL CONTROL SYSTEM


Section I Heating System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-1
II Air Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .13-15
III Winterization Equipment.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-18

CHAPTER 14 HOIST AND WINCHES


Section I Personnel Rescue Hoist. . . . . . . . . . . . . . . . . . . . . . . . . . . .14-1
II Cargo Suspension Assembly. . . . . . . . . . . . . . . . . . . . . . . . . 14-76

CHAPTER 15 AUXILLIARY POWER PLANTS


(Not Applicable) . . . . . . . . . . . . . . .. . . . . . . . . . . . . .15-1

CHAPTER 16 MISSION EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..16-1

CHAPTER 17 EMERGENCY EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1

APPENDIX A REFERENCE. . . . . . . . . . . . . . . . . . . . . . . . . . A-1

APPENDIX B MAINTENANCE ALLOCATION CHART


Section I Three Levels of Maintenance Concept. . . . . . . . . . . . . . . .B-1
II Maintenance Allocation Chart . . . . . . . . . . . . . . . . . . B-6
III Tools and Test Equipment. . . . . . . . . . . . . . . .B-76

APPENDIX C AIRCRAFT INVENTORY MASTER GUIDE . . . . . . . . . . . . . . . C-1

APPENDIX D ILLUSTRATED FIELD MANUFACTURE ITEMS LIST . . . . . . D-1

APPENDIX E STORAGE OF AIRCRAFT


Section I General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
II Flyable Storage. . . . .. . . . . . . . . . . . . . . . . .E-2
III Short Term Storage. . . . . . . . . . . . . . . . . . . . . . . .E-3
IV Intermediate Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10

APPENDIX F WIRING DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . .F-1

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index 1

iii/(iv blank)
TM 55-1520-210-23-3

APPENDIX A
REFERENCES

AR 95-1 Army Aviation General Provisions and Flight Regulations


AR 95-3 Weight and Balance Army Aircraft

AR 310-50 Authorized Abbreviations and Brevity Codes


DA Form 2028 Recommended Changes to Publications and Blank Forms
DA Form 2408-13 Aircraft Inspection and Maintenance Record

DA Form 2410 Component Removal and Repair/Overhaul Record


DA PAM 501 Hearing Conservation
DA PAM 738-750 Functional Users Manual for the Army Maintenance Management Systems

DA PAM 738-751 Functional Users Manual for the Army Maintenance Management Systems-Aviation (TAMMS-A)
FM 3-5 NBC Decontamination

FM 10-68 Aircraft Refueling

FM 10-69 Petroleum Supply Point Equipment and Operation

MIL-STD-12C Abbreviations for Use on Drawings, Specifications, Standards and in


Technical Documents

TB 1 -1500-341-01 Aircraft Components Requiring Maintenance Management and Historical Data Reports

TB 1-1615-351-23 Rotor Blade Erosion Protection

TB 43-0002-3 Maintenance Expenditure Limitations for Army Aircraft


TB 43-0106 Aeronautical Equipment Army Oil Analysis Program (AOAP)

TB 43-180 Calibration Requirements for the Maintenance of Army Materiel

TB 55-1500-314-24 Handling, Storage, and Disposal of Army Aircraft Components Containing


Radioactive Materials

TB 55-1500-334-25 Conversion to Fire Resistant Hydraulic Fluid

TB 55-1500-337-24 Phased Maintenance System for Army Aircraft


TB 55-9150-200-24 Engine and Transmission Oils, Fuels, and Additives for Army Aircraft

TB 750-25 Maintenance of Supplies and Equipment Army Metrology and Calibration System
TM 1-1500-204-23-1 General Aircraft Maintenance Manual
thru 10
TM 1-1500-328-23 Aeronautical Equipment Maintenance Management Policies and Procedures
TM 1-1500-344-23 Aircraft Weapons Systems Cleaning and Corrosion Control

TM 1-1520-250-23 General Tie-Down and Mooring

Change 8 A-1
TM 55-1520-210-23-3

TM 1-1520-256-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aviation Unit Maintenance (AVUM) and Aviation Intermedi-


ate Maintenance (AVIM) manual Nondestructive Inspection
Procedures for UH-1 Helicopter Series.
TM 9-1005-224-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Organizational, DS, and GS Maintenance Manual for Ma-
chine Gun, 7.62MM Machine Gun
TM 9-1345-201-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mine Dispersing Subsystem. Aircraft M56
TM 9-1345-201-30&P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Support Maintenance Manual (Including Repair Parts
and Special Tools List): Mine Dispensing Subsystem, Air-
craft: M56 (NSN 1345-00-313-1398)
TM 11-1520-210-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Organizational Maintenance Manual: Electronic Equipment
Configurations, Army Model UH-1D/H Helicopter (NSN
1520-00-859-0670) UH-1H (1520-00-087-7673) and UH-1V
(1520-01-043-4949) Helicopters
TM 11-1520-210-E&C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equipment Serviceability Criteria for Electronic Equipment
Configuration in Army Models UH-1B/C/D Helicopters
TM 11-1520-210-34P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Support and General Maintenance Repair Parts and
Special Tools List (Including Depot Maintenance Repair
Parts and Special Tools): Electronic Equipment Configura-
tion. Army Models UH-1D and UH-1H Helicopters
TM 11-5821-333-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit and Intermediate Maintenance Manual for Sincgars Air-
borne Combat Network Radio
TM 11-5821-333-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aviation Intermediate Maintenance Manual for Sincgars Air-
borne Combat Network Radio
TM 11-5841-272-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Organizational Maintenance Manual. Altimeter Set, Elec-
tronic, AN/AP-N-171A(V)1
TM 11-5895-776-13-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator, Organizational, Direct Support and General Sup-
port Manual, Counter measures System, Radio AN/ARQ-33
TM 11-6125-220-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operational Maintenance Manual: Motor-Generators
PU-543/A, PU-543A/A, PU-543B/A, and PU-543C/A
(MS-21983)
TM 11-6140-203-14-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operators Organizational, Direct Support, General Support
and Depot Maintenance Manual Including Repair Parts and
Special Tools Lists: Aircraft Nickel-Cadmium Batteries
TM 55-1500-335-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nondestructive Inspection Method
TM 55-1500-342-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Army Aviation Maintenance Engineering Manual: Weight
and Balance
TM 55-1500-345-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Painting and Marking of Army Aircraft
TM 55-1520-210-PM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UH-I H/V Aircraft Phased Maintenance Checklist
TM 55-1520-210-PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UH-1H/V Aircraft Preventive Maintenance Daily Inspection
Checklist
TM 55-1520-210-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator’s Manual: Army Model UH-1H/V Helicopter
TM 55-1520-210-23P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aviation Unit and Intermediate Maintenance Repair Parts
and Special Tools List (Including Depot Maintenance Repair
Parts and Special Tools)
TM 55-1520-242-MTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aircraft Maintenance Test Flight Manual for UH-1 and EH-1
Helicopters
TM 55-1520-242-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation for Shipment of UH-1 Helicopters
TM 55-1680-320-23&P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Performance Rescue Hoist
TM 55-2620-200-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection. Maintenance Instructions. Storage. and Disposi-
tion of Aircraft Tires and Inner Tubes
TM 55-2840-229-23P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aviation Unit and Intermediate Maintenance Repair Parts
and Special Tools List

A-2 Change 9
TM 55-1520-210-23-3

TM 55-4920-201-14 Operator’s Organizational. DS and GS Maintenance Manual Including Repair Parts and
Special Tool List Balancing and Adapter Kits (Marvel)
TM 55-4920-244-14 Operator’s Organizational. Direct Support and General Support Maintenance Manual
TM 750-244-1-5 Procedures for Destruction of Aircraft and Associated Equipment to Prevent Enemy Use

Change 8 A-3/(A-4 blank)


TM 55-1520-210-23-3

APPENDIX B

MAINTENANCE ALLOCATION CHART


SECTION I. THREE LEVELS OF MAINTENANCE CONCEPT

INTRODUCTION

B-1. MAINTENANCE ALLOCATION conserve personnel and equipment resources and


CHART. air mobility requirements.)

a. This Maintenance Allocation Chart (MAC)


assigns maintenance functions in accordance with (a) Company Size Aviation Units: Perform
those tasks which consist primarily of preventive
the Three Levels of Maintenance concept for army
maintenance and maintenance repair and
aircraft. These maintenance levels, Aviation Unit
Maintenance (AVUM); Aviation Intermediate replacement functions associated with sustaining a
Maintenance (AVIM) and Depot Maintenance are high level of aircraft operational readiness. Perform
depicted on the MAC as: maintenance inspections and servicing to include
preflight, daily, intermediate, periodic and special
inspections as authorized by the MAC or higher
AVUM which corresponds to the O Code in the headquarters. Identify the cause of
RPSTL. equipment/system malfunctions using applicable
AVIM which corresponds to an F Code in the technical manual troubleshooting instructions,
RPSTL. built-in-test equipment (BITE), installed aircraft
DEPOT which corresponds to a D Code in the instruments, or easy to use/interpret
RPSTL diagnostic/fault isolation devices (TMDE). Replace
worn or damaged modules/components which do
not require complex adjustments or system
alignment and which can be removed/installed
b. The maintenance to be performed below with available skills, tools and equipment. Perform
depot and in the field as described as follows: operational and continuity checks and make minor
repairs to the electrical system. Inspect, service and
(1) Aviation Unit Maintenance (AVUM) make operational, capacity and pressure checks to
activities will be staffed and equipped to perform hydraulic systems. Perform servicing, functional
high frequency “On-Aircraft” maintenance tasks adjustments, and minor repair/replacement to the
required to retain or return aircraft to a serviceable flight control, propulsion, power train and fuel
condition. The maintenance capability of the systems. Accomplish air frame repair which does
AVUM will be governed by the Maintenance not require extensive disassembly, jigging, or
Allocation Chart (MAC) and limited by the amount alignment. The manufacture of air frame parts will
and complexity of ground support equipment be limited to those items which can be fabricated
(GSE), facilities required, and number of spaces with tools and equipment found in current air
and critical skills available. The range and quantity mobile tool and shop sets. Evacuate unserviceable
of authorized spare modules/components will be modules/components and end items beyond the
consistent with the mobility requirements dictated repair capability of AVUM to the supporting AVIM.
by the air mobility concept. (Assignments of
maintenance tasks to divisional company size (b) Less than Company Size Aviation Units:
aviation units will consider the overall maintenance Aviation elements organic to brigade, group,
capability of the division, the requirement to battalion headquarters and detachment size units

B-1
TM 55-1520-210-23-3

are normally small and have less than ten aircraft collection and classification services for
assigned. Maintenance tasks performed by these serviceable/unserviceable material. Operates a
units will be those which can be accomplished by cannibalization activity in accordance with AR
the aircraft crew chief or assigned aircraft 750-50. (The aircraft maintenance company within
repairman and will normally be limited to the maintenance battalion of a division will
preventive maintenance, inspections, servicing, perform AVIM functions consistent with air
spot painting, stop drilling, application of nonstress mobility requirements and conservation of
patches, minor adjustments, module/component personnel and equipment resources. Additional
fault diagnosis and replacement of selected intermediate maintenance support will be provided
modules/components. Repair functions will by the supporting nondivisional AVIM unit.)
normally be accomplished by the supporting AVIM
unit. B-2. USE OF THE MAINTENANCE
ALLOCATION CHART.
(2) Aviation Intermediate Maintenance
(AVIM) provides mobile, responsive “One Stop” a. The Maintenance Allocation chart assigns
maintenance support. (Maintenance functions maintenance functions to the lowest level of
which are not conducive to sustaining air mobility maintenance based on past experience and the
will be assigned to depot maintenance). Performs following consideration:
all maintenance functions authorized to be done at
AVUM. Repair of equipment for return to user will (1) Skills available.
emphasize support or operational readiness
requirements. Authorized maintenance includes (2) Time required.
replacement and repair of modules/components
and end items which can be accomplished (3) Tools and test equipment required and/or
efficiently with available skills, tools, and available.
equipment. Established the Direct Exchange (DX)
program for AVUM units by repairing selected b. Only the lowest level of maintenance
items for return to stock when such repairs cannot authorized to perform a maintenance function is
be accomplished at the AVUM level. Inspects, indicated.
troubleshoots, tests, diagnoses, repairs, adjusts,
calibrates, and aligns aircraft system c. A maintenance function assigned to a
modules/components. AVIM units will have the maintenance level will automatically be authorized
capability to determine the serviceability of to be performed at any higher maintenance level.
specified modules/components removed prior to
the expiration of the Time Between Overhaul (TBO) d. A maintenance function that cannot be
or finite life. Module/component disassembly and performed at the assigned level of maintenance for
repair will support the DX program and will any reason may be evacuated to the next higher
normally be limited to tasks requiring cleaning and maintenance organization. Higher maintenance
the replacement of seals, fittings and items of levels will perform the maintenance functions of
common hardware. Air frame repair and lower maintenance levels when required or directed
fabrication of parts will be limited to those by the appropriate commander.
maintenance tasks which can be performed with
available tools and test equipment. Unserviceable e. The assignment of a maintenance function
reparable modules/components and end items will not be construed as authority to carry the
which are beyond the capability of AVIM to repair associated repair parts in stock. Authority to
will be evacuated to Depot Maintenance. This level requisition, stock, or otherwise secure necessary
will perform aircraft weight and balance repair parts will be as specified in the repair parts
inspections and other special inspections which appendix.
exceed AVUM capability. Provides quick response
maintenance support, including aircraft recovery f. Normally there will be no divation from the
and air evacuation, on-the-job training, and assigned level of maintenance. In cases of
technical assistance through the use of mobile operational necessity, maintenance functions
maintenance contact teams. Maintains authorized assigned to a higher maintenance level may, at the
operational readiness float aircraft. Provides request of the lower maintenance level, be

B-2
TM 55-1520-210-23-3

specifically authorized by the maintenance officer of d. Adjust. To maintain, within prescribed limits,
the level of maintenance to which the function is by bringing into proper or exact position, or by
assigned. The special tools, equipment, etc. required setting the operating characteristics to specified
by the lower level of maintenance to perform this parameters.
function will be furnished by the maintenance level to
which the function is assigned. This transfer of a e. Align. To adjust specified variable elements
maintenance function to a lower maintenance level of an item to bring about optimum or desired
does not relieve the higher maintenance level of the performance.
responsibility of the function, The higher level of
maintenance has the authority to determine: f. Calibrate. To determine and cause corrections
to be made or to be adjusted on instruments or test
(1) If the lower level is capable of performing the measuring and diagnostic equipments used in
work. precision measurement. Consists of comparisons of
two instruments, one of which is a certified standard
(2) If the lower level will require assistance or of known accuracy, to detect and adjust any
technical supervision and on-site inspection. discrepancy in the accuracy of the instrument being
compared.
(3) If the authorization will be
granted to perform maintenance. g. Install. The act of emplacing, seating, or fixing
into position an item, part, or module (component
g. Organizational through depot maintenance of
or assembly) in a manner to allow the proper
the U.S. Army Electronics Command equipment will
functioning of an equipment or system.
be performed by designated U.S. Army Electronics
Command personnel. h. Replace. The act of substituting a serviceable
h. Changes to the Maintenance Allocation Chart like type part, subassembly, or module (component
will be based on continuing evaluation and analysis or assembly) for an unserviceable counterpart.
by responsible technical personnel and on reports
received from field activities. i. Repair. The application of maintenance
services or other maintenance action to restore
B-3. DEFINITIONS. serviceability to an item by correcting specific
damage, fault, malfunction, or failure in a part,
Maintenance functions. Maintenance functions will subassembly, module (component or assembly),
be limited to and defined as follows: end item, or system.

a. Inspect. To determine the serviceability of an j. Overhaul. That maintenance effort


item by comparing its physical, mechanical and/or (service/action) necessary to restore an item to a
electrical characteristics with established standards completely serviceable/operational condition as
through examination. prescribed by maintenance standards (i.e. DMWR)
in appropriate technical publications. Overhaul is
b. Test. To verify serviceability and detect normally the highest degree of maintenance
incipient failure by measuring the mechanical or performed by the Army. Overhaul does not
electrical characteristics of an item and comparing normally return an item to like new condition.
those characteristics with prescribed standards.
k. Rebuild. Consists of those services/actions
c. Service. Operations required periodically to necessary for the restoration of unserviceable
keep an item in proper operating condition, i.e. to equipment to a like new condition in accordance
clean (decontaminate), to preserve, to drain, to with original manufacturing standards. Rebuild is
paint, or to replenish fuel, lubricants, hydraulic the highest degree of materiel maintenance applied
fluids, or compressed air supplies. to Army equipment. The rebuild operation includes
the act of returning to zero those age measurements
(hoursmiles, etc.) considered in classifying Army
equipments/components.

Change 4 B-3
TM 55-1520-210-23-3

B-4. STANDARD GROUPS. groupings as individual chapters with sections in


The standard groupings shown below are used, as each chapter relative to the individual complete
applicable, throughout this MAC Maintenance systems, subsystems, modules, components,
manuals and RPSTLs reflect these standard assemblies, or specific parts noted.
AIRFRAME ITEMS

GROUP GROUP
NUMBER DESCRIPTION NUMBER DESCRIPTION

00 Aircraft System 06 Drive Train Systems


01 Aircraft General Transmissions, gearboxes, clutches,
Servicing, handling, inspection shafting, oil systems, bearings,
lubrication hangers, oil tanks, and freewheeling
requirements,
overhaul and units.
requirements,
retirement requirements, cleaning, Hydraulic and Pneumatic Systems
07
mooring, towing, jacking, hoisting,
preservation requirements, weight Pumps, filters, reservoirs, cylinders,
and balance requirements, spot valves, servos, motors, starters and
painting, complete painting, and
accumulators.
subassembly painting requirements.
Airframe 08 Instrument Systems
02
Fuselage, empennage, pylons, wings, Flight instruments, navigation
mounts (engine and transmission), instruments, engine instruments,
armor, seats, ramps, decks, and miscellaneous instruments (i. e.,
tiedowns. clocks), sending units, panels, and
flow meters.
03 Alighting Gear
09 Electrical Systems
Landing gear, skids, floats, skis, struts,
wheel brakes, and mechanical Motors, actuators, regulators,
mechanisms. generators, starters, batteries,
lighting, caution and warning lights,
04 Power Plant Installation inverters, fault isolation systems, rotor
brakes, and avionics provisions.
Removal, installation, cooling
systems, air induction, exhaust, oil 10 Fuel Systems
systems, components, ignition
systems, power control, harnesses, Tanks, cells, filters, pumps, valves,
carburetors, fuel controls, pumps auxiliary fuel systems, and refueling
(engine driven), filters/particle systems.
separators, and Quick Change
Assemblies (QCA). (See Power Plant
Items, figure 2, for more detailed 11 Flight Controls System
functions.)

05 Propellers/Rotors Systems Control sticks, pedals, cables, pulleys,


Propellors, governors, rotors (main and push-pull rods, torque tubes,
tail), hubs, blades, dampeners, stabilizer quadrants, force gradients, control
bars, swashplates, hub moment springs, surfaces, bellcranks, and trim
and support assemblies. actuators (mechanical).

B-4 Change 1
TM 55-1520-210-23-3

GROUP GROUP
NUMBER DESCRIPTION NUMBER DESCRIPTION

12 Utility System. 16 Mission Equipment

Fire detecting/extinguishing systems, Spraying equipment, stores, racks,


oxygen systems, windshield wiper armament, reconnaissance, photo-
systems, mirrors, and de-ice/anti-ice graphy,pods, and litters.
systems.
17 Emergency Equipment
13 Environmental Control Systems (ECS)
Ejection seats, canopies, jettison
Heaters, air conditioners, defrosters, system, portable fire extinguishers,
control mixing valves, and ducts. axes, and first aid kits.

14 Hoists and Winches Installed Avionics Components

Cargo/rescue hoists, winches, hooks, 18 Communications and Navigational


slings, loading systems, and Black Boxes.
emergency release systems.
15 Auxiliary Power Plants (APP)

Fuel, exhaust, and ducting.

B-5. SYMBOLS. B-7. TOOLS AND TEST EQUIPMENT/


(SECTION III).
The letters “AVUM, AVIM AND DEPOT” as placed
on the Maintenance Allocation Chart indicate the Special tools, test, and support equipment required to
level of Maintenance responsible for performing the do maintenance functions are listed with a reference
particular maintenance function based upon number to permit cross-referencing to column 5 in
assigned skills, tools and test equipment and time the MAC. In addition, the maintenance category
required to accomplish maintenance. authorized to use the device is listed along with the
item National Stock Number and if applicable, the
number to aid in identifying the tool/device.
B-6. WORK TIMES.
B-8. REMARKS (SECTION IV).
The symbol -o— identifies the level of Maintenance
authorized to perform a maintenance function and Column 6 of the MAC contains alphabetic reference
indicates that work time figures are being developed codes which are explained in Section IV of this
and will be entered at a later date. When developed, appendix.
this time will appear: for example, as 0.1 and also
indicates the level of authorized maintenance.

B-5
TM 55-1520-210-23-3

SECTION II. MAINTENANCE ALLOCATION CHART


MAINTENANCE ALLOCATION CHART
NOMENCLATURE OF END ITEMS
HELICOPTER UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

NOTE

The extent of maintenance to be performed by AVUM as indicated in this MAC is governed by the size of the
Unit and the TOOlS authorized (Refer to paragraph B-1 b(1) a. and b.). Specific notes are given to further
Identify or describe the extent or limit of maintenance to be performed.
0100 Aircraft General

0101 Clean — ● —

0102 Moor — ● —

0103 Tow — ● — 100

0104, Jack — ● — 100,102

0105 Hoist — ● —

0106 Preservation — ● — 100,102

0107 Weight & Balance 102,118


121

0108 Spot Paint — ● — 100

0109 Complete Painting

0110 Sub-Assembly 118


Painting
0110 Servicing 100,102

0200 Airframe Inspect

Repair 100,102 A
103

117,120, 118

Overhaul

B-6
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg:3l0.10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL, TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0201 Tail Boom Assy Inspect

Replace 100, 102 B

Repair 100, 102 A


103
102, 117
Overhaul

0202 Fuselage Inspect

Repair 100, 102 A


103
102, 117

0202 Sheet Metal for Inspect


01 Structural Members
and Honeycomb Replace 100, 102 A
Panels not requiring 103
Jigs and Fixtures
Repair 100, 102 A
103
102, 117
0202 Sheet Metal for Inspect
02 Structural Members
and Honeycomb Panels Replace
that require Jigs &
Fixtures Repair

0202 Honeycomb Panels Inspect


03 Replace 100, 102
Repair 100, 102 A
103
102, 117

B-7
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Cabin Nose Assembly


04

0202 Lower Windows Inspect


04
01 Replace 100,102

Repair 100, 102 D

0202 Windshield Inspect


04
02 Replace 100, 102

Repair 100, 102 D

0202 Ejection Handles Inspect


04
03 Replace 100, 102

Repair 100, 102

Doors, Crew Inspect


05
Adjust 100, 102

Replace 100, 102

Repair 100, 102


103
SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete
1 Apr 77

B-8
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCL4TURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Window Assembly Inspect — ● —


05
01 Replace — ● _ 100 102

Repair - + - 100 102 D

0202 Striker Assembly Inspect — ● —


05
02 Replace - ● _ 100 102

Repair — ● __ 100 102


103

0202 Handle Assembly Inspect — ● —


05
03 Replace — ● _ 100 102

Repair — ● — 100 102


103

0202 Cabin Roof Assembly


06

0202 Windows Inspect — ● _


06
01 Replace - ● 100, 102

Repair — ● — 100, 102 D

0202 Air Vent Pans Inspect — ●


06
02 Replace — ● — 100, 102

Repair — ● — 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-9
TM 55-1520-210-23-3

B-10 Change 8
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS

HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H\UH-1V\EH-1H


(1) (2) (3) (4) (5) 1

(6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Armor Inspect


08
03 Replace 100, 102
01
Repair 100, 102,
103
Carriage Assy Inspect 100 ,102
0202
08 Replace 100,102,
03 103
02 Repair 102, 117
120

0202 Seat Installation, Inspect


09 Passenger
Repair 100, 102

0202 Seat Inspect


09
01 Replace 100,102

Repair 100,102 AG

0202 Seat Belts Inspect


09
02 Replace 100 ,102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-10.1/(B-10.2 blank)
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS

HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H


(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 SEAT, CREW Inspect - ● — EH-1H


10 Only
Service - ● — 100, 102

Adjust - ● — 100, 102

Replace — ● — 100, 102

Repair — ● - 100, 102 A

- ● — 102,117
120
0202 Blanket Assembly, Inspect — ● —
11 Soundproofing
Replace — ● — 100,102

Repair — ● _ 100,102
— ● — 102,117

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-11
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCIATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/\UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Window Inspect


12
01 Replace 100,102

Repair 100,102 D

0202 Latch Inspect


12
02 Repair 100,102

0202 Door Assembly, Inspect


13 Equipment
Replace 100,102

Repair 100, 102


103

0202 Inspection Doors Inspect


14
Replace 100,102

Repair 100, 102


103

0202 Deck Assembly, Inspect


15 Left and Right
Engine Align

Replace 100,102

Repair 100, 102 A


103

102, 117

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-12
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Deck Assembly, Inspect


16 Center Engine
Align — ● — 100,T89 E
T90,102

Replace — ● — 100,102 E
103,T89 T90

Repair 100,102 A
103

— ● — 102,117

0202 Mount Assembly Inspect


17
Align 100,102

Replace 102,100

Repair 102,100 A
1 0 3
102,117 AH
120
0202 Cowl Assemblies Inspect
18
Replace 102,100

Repair 102,103
100
— ● _ 102,117
0202 Baffle Assembly Inspect
19
Replace 103,100
102

Repair 103,100
102
— ● — 102,117

B-13
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY , TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0202 Firewall Assembly Inspect


20
Replace 103,100
102

Repair 103,100
102
102,117
0202 Heatshield Assy Inspect
21
Replace 103,100
102

Repair 103,100
102

102,117
0202 Mount Installation,
22 Engine

0202 Support Arms Inspect


22 (Brace Rods,
01 Tripod, and Replace 102,T10
(Bi-Pod) 100

Repair 102,100 F

102,120 AH

0202 Pillow Block Inspect


22 Assy
02 Replace 102,T10
100

Repair 102,100

0202 Map and Data Case Inspect


23
Replace 102,100
Repair 100,102 AG

B-14
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0300 Alighting Gear Assembly

0301 Cross Tubes Inspect 100,102

Replace 102,100

Repair 103,100 A
102

0302 Skid Tubes Inspect

Replace 102,100

Repair 100,102 A
103

0303 Skid Shoes Inspect

Replace 102,100

Repair 100,102 A
103
102,117 AH
120

0304 Skid Saddles Inspect

Replace 100,102

0305 Truck (Ground Han- Inspect


dling Wheels)
Replace 100,102

Repair 100,102
103

B-15
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
1
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0305 Pump Assembly Inspect


01
Test
Replace 102,100
Repair 111,102

0305 Cylinder Assembly Inspect


02
Replace 102,100

Repair 111,102

0305 Wheel Assembly Inspect


03
Replace 102,100

Repair 100,102

0306 Skid Installation, Inspect


Tail
Replace 102,100

Repair 102,100
103

0307 Ski Isolation Inspect


Damper

Install 100,102

Replace 100,102

Repair 100,102

B-16
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER UTILITY TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(3) (5) (6)
(1) (2)
MAINTENANCE CATEGORY TOOLS
GROUP AND
MAINTENANCE
FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARK
NUMBER COMPONENT/ASSEMBLY

0400 Power Plant Installation

0401 Engine (Complete Assy) Inspect — ● —

Test ● 100,102 H
108
— ● — 102,119

Service — ● —

Replace — ● — 10,53
100,102
108

Repair 100,102 G
108
102,112
119
Overhaul

DELETED

0402 Particle Separator Inspect

Replace 102,100

100,103 A
Repair
102
102,117 AH
120

0403 Tail Pipe Inspect

Replace 102,100,

Repair 100,102 A

102,120 AH

Change 4 B-17
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
MAINTENANCE TOOLS
NUMBER COMPONENT/ASSEMBLY FUNCTION AND
AVUM AVIM DEPOT EQUIPMENT REMARKS
0404 Heat Suppressor Inspect
Replace 102,100
Repair 100,103
102
0405 Actuator, Linear Inspect 102,117

Adjust 102,100
Replace 100,102
Repair 102,100
Repair
0406
Controls, Power Inspect
Lever
Adjust 102,100
Replace 102,100
Repair 102,100
0407 Droop Compensator Inspect
Adjust 102,100
Replace 102,100
Repair 102,100

0408 Oil Tank, Engine Inspect


Test 102,100
Service 102,100
Replace 102,100
Repair 102,100
102,120

B-18
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1 H

(1) (2) (3) (4) (5) (6)


GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0409 Hoses, Fittings, Inspect


and Tubing
Replace 102,100

0410 Oil Cooler, Engine Inspect


Test
Replace 102,100
Repair 102,100 M

0411 Blower, Turbine Inspect


Replace 102,100
Repair 119,102 AH
112,118
120

0412 Chip Detector, Inspect


Engine
Test 102,100
Replace 102,100

0413 Filter Assembly, Inspect


Inlet
Replace 102,100
Repair 102,100

0414 Valves, Breakaway Inspect


Replace 100,102

0415 External Filter Inspect 100,102,


1 07
Replace
Repair

0416 Oil Separator Inspect 100,102,


(Lubriclone) 107
Replace
Repair

Change 5 B-19
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H

(1) (2) (3) (4) (5) (6)


GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0500 Rotor Systems

0501 Pylon Assembly, Inspect


External Components
Replace 102,100

Repair 100,102 A
103

0502 Stabilizer Bar Assy Inspect

Adjust 102,113 K
T99A

Replace 102,100

Repair 102,100 D
102,116

0503 Hub and Blade Assy, Inspect


Main Rotor
Adjust 101,102 L

Align T34,T39
T40,T41
T49,T62
101,102

Replace T11,T12
T13,T22
T34,T41
T49,T53
102,101

B-20
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0503 Hub Assembly Inspect


01
Service

Adjust T34,T41,
T49,T59,
T62,102,
116

Align 102,109 K
101

Replace 102,109
101

Repair 100,102 M

T34,T41,
T49,T72
109,102

Overhaul

0503 Drag Brace Assy Inspect


01
01 Replace 102,109,
101

Repair 102,109,
101

0503 Grip Assembly Inspect


01
02 Replace

Repair 109,100 M
102
102,113 D

B-21
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg: 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0503 Shield Assembly Inspect


01
03 Replace 113,114
102

Repair 113,114
102

Inspect
0503 Oil Reservoirs &
01 Sight Glasses
04 Replace 102,109
100

0503 Strap Assembly, Inspect


01 Tension
05 Replace 113,114
102

0503 Pitch Horn Assy Inspect


01
06 Replace 102,109
100

Repair 102,109
100

0503 Trunnion Assembly Inspect M


01
07
Replace

Repair 109, 100 M


102
102, 114,
113

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-22
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Req 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(4) (5)
(1) (2) (3) MAINTENANCE CATEGORY TOOLS
GROUP MAINT AND (6)
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQPT REMARKS

0503 Bolt Assy, Blade Inspect - • -


01 Retention
08 Replace - • - 102,109
100

Repair - • - 102,109
100

0503 PiIIOW Block Assy Inspect - • -


01
09
Service - • - 100,102

Replace - • - 113,114
102

Repair - • - - • - 109, M
100,102

0503 Yoke Assembly Inspect - • -


01
10
Replace - • -

Repair - • - 109,100,102 M

- • - 102,113,114 M
Plate Assy Inspect - • - - • -
0503
Replace - • - 102, 109
01(11)
0503 Blade Assy, Main Inspect - • -
02 Rotor
Replace - • - T34,T45
T49,T85
109, 101
102

Repair - • - T34,T45
T49,T85
109, 101
102

Overhaul - •-

Change 2 B-23
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURES OF END ITEMS
HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-lH/UH-1V/EH-lH
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0504 Scissors and Sleeve Inspect - • -


Assembly
Replace - • - 109, 101
101, T99A
Overhaul - • -

Repair - • - 109,102
100
- • - T36,T37
T38,T50
T58,102
109,113
114

0504 Link Assy. Scissors Inspect - • -


01
Replace - • - 109,100
102

Repair - • - 109,100
102

0504 Scissors Assembly Inspect - • -


02
Replace - • - 109,100
102

Repair - • - 109,100
102
T99A
0504
Hub Assembly Inspect - • -
03
Replace - • - 102,113
114
Repair - • - 109,100 D
102
- • - 102
113,114

B-24 Change 4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY . TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0504
Sleeve, Collective Inspect - • -
04
Replace - • -

Repair - • - 100 , 109 D


102
Repair - • -
0505 Swashplate and Inspect - • -
support Assy
Replace - • - 100, 102
109

Repair - • - 100, 102 M


109

Overhaul - • -

0506 Damper Assembly, Inspect - • -


Stabilizer

Service - • - 100, 102


109

Adjust - • - 100, 102


109

Replace - • - 100, 102


109

Repair - • - 100, 102 M


109

0507 Rotor Installation, Inspect - • -


Tail
Replace - • - 100, 102
109

Repair - • - 100, 102


109

B-25
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP , MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0507 Link Assembly Inspect - • -


01
Replace - • - 100, 102,
109

Repair - • - 100, 102,


109

0507 Crosshead Inspect - • -


02
Replace - • - 100, 102,
109

Repair - • - 100, 102,


109

0507 Hub and Blade Inspect - • -


03 Assembly
Adjust - • - 100, 102, L
109
Align - • - T1, T73, T75, K
T78, T85, 102
100, 109
Replace - • - 102, 109, M
100

Repair - • - 109, 100 M

- • - 102, 113,
114

0507 Blade Assembly inspect - • -


03
(01) Replace - • - 100, 102

Repair - • - 100, 102 D


- • - 102, 113
114

B-26
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(2) (3) (4) (5) (6)
(1)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS
NUMBER COMPONENT/ASSEMBLY

0507 Hub Assembly Inspect


03 100, 102,
02 Service
109
Adjust T44, 100,
102, 109
Replace 102, 109,
100

Repair 102, 109, M


100
T43, T44,
102, 113,
114

0600 Drive Train

0601 Transmission and Inspect


Mast Assembly
Replace T19, T21,
T53, 102,
101, 109

Repair 100, 102, M


109,

102, 113

0601 Mast Assembly Inspect


01
Replace T53, 101
102, 109,

Repair 100, 102, M


109
102,113
Overhaul

B-27
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5} (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0601 Spring Inspect - • - - • - M


01
Replace - • - 102,109

0601 Upper Bearing Inspect -•-


01 Assembly
(01) Replace - • -

0601 Support ASSY Inspect - • - - • - M


01
03 Replace - • - 102,109

B-28 Change 4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0601 Transmission Assy. Inspect - • -


02
Test - • - 100, 102

Service - • - 100, 102

Replace - • - T19, T21


T53, 102,
101, 109

Repair - • - T19, T21


T53, 100
102, 109
- • - 102, 113
Overhaul

0601 Pressure Relief Inspect - • -


02 Valve
01 Replace - • - 100,102
109

Repair - • - 102, 113

0601 Lines, Fittings, Inspect - • -


02 Manifolds, and
02 Screens Replace - • - 100, 102
109

Repair - • - 100, 102


109

0601 Oil Jets Inspect - • -


02
03 Replace - • - 100, 102
109

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
Change 2 B-28.1/(B-28.2 blank)
*U.S. Government Printing Office: 1989-654-047/1004
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0601 Filter Assembly Inspect - • -


02 (Primary)
04 Replace - • - 100, 102
109

Repair - • - 100, 102


109

0601 Input Drive Inspect - • -


02 Quill
05 Replace - • - T31 , T57
102, 101
109

Repair - • - T31 , T57


102, 113

Overhaul - • -

0601 Offset Quill Inspect - • -


02
Replace - • - 101, 102
06
109

Repair - • - T26, 102


113

Overhaul - • -

0601 Hydraulic Pump Inspect - • -


02 and Tachometer
07 Drive Quill Replace - • - T31, 101
102, 109

Repair - • - T31, 102


113

Overhaul - • -

B-29
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0601 Tail Rotor Inspect - • -


02 Quill
08 Replace - • - T31 , T60,
102, 101,
109

Repair - • - T31, T60,


102, 113

Overhaul. - • -

0601 Sight Gages Inspect - • -


02
09 Replace - • - 100, 102,
109

0601 Chip Detector Inspect - • -


02
10 Test - • - 100,102
109
Replace - • - 100, 102.
109

0601 Oil Pump Inspect - • -


02 Assembly
11 Test - • - 102, 113

Replace - • - 102, 101,


109

Repair - • - 102, 113

Overhaul - • -

0601 Debris Monitor Inspect - • - 100, 102,


02 107
12 Test - • -

Replace - • -

B-30 Change 4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0602 Main Drive Shaft Inspect - • -


(Engine to Trans-
mission Bell) Service - • - T29, T48,
100, 102,
109

Align - • - T47, T51 ,


T53, 100,
102, 109

Replace - • - T29, T48,


100, 102,
109

Repair - • - T29, T48,


100, 102,
109

Overhaul - • -

0603 Main Drive Shaft Inspect - • -


(Engine to Trans-
mission Kaflex) Align - • - T47, T51 ,
T53, 100,
102, 109

Replace - • - 100, 102,


109

Repair - • - 100, 102,


109

Overhaul - • -

0604 Oil Cooler Inspect - • -

Replace - • - 100, 102,


109

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-31
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY , TOOLS
MAINTENANCE 1
AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0605 External Oil Inspect - • -


Filter
Replace - • - 100, 102,
109

0606 Manifold Assembly Inspect - • -

Replace - • - 100, 102,


109

Repair - • - 100, 102,


109

0607 Tail Rotor Drive Inspect - • -


Shaft
Align - • - 102,113

Replace - • - 100, 102


109

Repair - • - 100, 102


109
- • -
0607 Tail Rotor Drive Inspect - • -
01 Shaft Hanger Assy.
Service - • -

Replace - • - 100, 102


109

Repair - • - 100, 102,


109,

Repair - • - 102, 113, AN


118

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-32
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0607 Tail Rotor 42° Inspect - • -


02 and 90° Gearbox

Service - • -

Replace - • - T33,T54
100,102
109

Repair - • - T2,T30 M
T34,T54
T55,T60
100,102
109
- • - 102,113
Overhaul - • -

0607 Tail Rotor 42° Inspect - • - T-72.1


02 and 90° Gearbox
Replace - • - 101,102 AK
(01) Quills
109
Repair l — 102,113 J

Overhaul - • -

0700 Hydraulic and Pneumatic Inspect - • -


Systems
Test - • - T88,100
104
- • - 111
0701 Cylinder Assy, Inspect - • -
Main Servo
Adjust - • - 100, 02
104

Replace - • - 104, 00
102

Repair - • - 104,100
102
Repair - • - 102.111 AN

B-33
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS
0701 Connecting Link, Inspect - • -
01 Clevis Fittings,
Plugs Replace - • - 104,100
102

0701 Servocylinder Assy Inspect - • -


02
Adjust - • - 100,102

Replace - • - 104,102
100

Repair - • - 104,100 I
102
- • - 102,111 J,AN

Overhaul - • -

0702 Hoses, Tubing and Inspect - • -


Fittings
Replace - • - 104,100
102

0703 Switch, Pressure Inspect - • -

Replace - • - 104,100
102

0704 Valve, Directional Inspect - • -

Replace - • - 104,100
102

0705 Filter Assembly Inspect - • -

Replace - • - 104,100
102

Repair - • - 104,100
102

B-34
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H\UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0706 Valve, Check Inspect - • -

Replace - • - 104, 100,


102

0707 Valve, Safety Inspect - • -


Relief
Replace - • - 104, 100,
102

0708 Valve, Irreversible Inspect - • -

Replace - • - 104, 100,


102

Repair - • - 104, 100, D


102

Overhaul - • -

0709 Tank, Hydraulic Inspect - • -


Fluid
Service - • - 100, 102,
104
Replace - • - 104, 100,
102

Repair - • - 104, 100, AG


102

0710 Pump, Axial Piston Inspect - • -

Replace - • - 104, 100,


102

Repair - • - 104, 100, D


102

Overhaul - • -

B-35
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY-TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0711 Coupling Halfs Inspect

Replace 104,100
102

0712 Servo Cylinder, Inspect


T/R
Replace 104,100
102

Repair 104,100 D
102

102,111 J,AN

0800 Instrument Systems

0801 Instrument Panel Inspect

Replace 100,102

Repair 100,102

102,110
8

0601 Glareshield Inspect


01
Replace 100,102

Repair 100,102

B-36
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY — T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0802 Miscellaneous
Instruments

0802 Clock Inspect - • -


01
Adjust - • - 100, 102,
106
Replace - Ž - 100, 102,
106

Overhaul - Ž -

0802 Free Air Temperature Inspect - Ž -


02 Gage
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

0802 Volt, Load and Inspect - Ž -


03 Amp Meter
Adjust - Ž - 100, 102,
106
Replace - Ž - 100, 102,
106

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-37
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0802 Fuel Quantity


04 Indicating System

0802 Fuel Quantity Inspect - Ž -


04 Indicator and
01 Amplifier Test - Ž - 101,102 AL
106

Adjust - Ž - 102,110

Replace - Ž - 100,102
106

Overhaul - Ž - 100,102
106

0802 Fuel Quantity Inspect - Ž -


04 Transmitter
02 Replace - Ž - 100,102
106

Repair - Ž - 100,102,
106

Overhaul
- Ž -

0802 Tank Sensors, Inspect - Ž - 102,110


04 Probes & Units
03 Test - Ž - 110,102

Replace - Ž - 110,102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-38
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILlTY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0803 Flight Instrument

0803 Vertical Velocity Inspect - Ž -


01 Indicator
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

overhaul - Ž -

0803 Stand-By Compass Inspect - Ž -


02
Adjust - Ž - 100, 102,
106
Replace - Ž - 100, 02,
106

0803 Airspeed Indicator Inspect - Ž -


03
Test - Ž - 100, 02,
106

Replace - Ž - 100, 102,


106

Repair - Ž - I 00, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-39
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0803 Altimeter Inspect - Ž -


04 Indicator
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Overhaul - Ž -

0803 Attitude Indicator Inspect - Ž -


05
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Overhaul - Ž -

0803 Turn & Slip Inspect - Ž -


06 Indicator
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 JuI 76, IS obsolete


1 Apr 77

B-40
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0803 Pitot System Inspect - Ž -


07
Test - Ž - 100, 102,
106

Calibrate - Ž - 102, 110,


118

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

0804 Engine Instruments

0804 Dual Tachometer Inspect - Ž -


01
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Overhaul - Ž -

0804 Exhaust Gas Inspect - Ž -


02 Temperature
Indicator Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, IS obsolete


1 Apr 77
B-41
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (3) (4) (5) (6)
(2) MAINTENANCE CATEGORY TOOLS
GROUP
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0804 Thermocouple Inspect - Ž -


02 Lead Spool
01 Resistor Test - Ž - 100, 102,
106

Adjust - Ž - 100, 102,


106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

0804 Oil Temperature Inspect - Ž -


03 Indicator
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

0804 Oil Pressure Inspect - Ž -


04 Indicator and
Transmitter Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-42
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER (COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0804 Fuel Pressure Inspect - Ž -


05 Indicator and
Transmitter Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

0804 Torquemeter and Inspect - Ž -


06 Transmitter
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

0804 Tachometer Inspect - Ž -


07 Generators
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-43
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY , TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0804 Gas Producer Inspect - Ž -


08 Tachometer
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

0804 Temperature Bulbs Inspect - Ž -


09
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

0805 Transmission
Instruments

0805 Oil Temperature Inspect - Ž -


01 Indicator
Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-44
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0805 Oil Pressure Inspect - Ž -


02 Indicator and
Transmitter Test - Ž - 100, 102,
106

Replace - Ž - 100, 102,


106

Repair - Ž - 100, 102,


106

Overhaul - Ž -

0900 Electrical System

0901 Wiring Inspect - Ž -

Test - Ž - 100, 102,


107

Replace - Ž - 100, 102,


107

Repair - Ž - 100, 102,


107

0902 Relays, Rheostats, Inspect - Ž -


Switches, Circuit
Breakers, Plugs, Test - Ž - 100, 102,
Leads, Connectors, 107
Conduits, Receptacles,
Shunts & Shock Mounts Replace - Ž - 100, 102,
107

Repair - Ž - 100, 102,


107

B-45
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0903 Battery Inspect - Ž -

Test - Ž - 100, 102, O


107

Service 102, 110 O


- Ž -

Replace - Ž - 100, 102,


107

Repair - Ž - 100, 102, O


107

0904 Regulator Inspect - Ž -

Adjust - Ž - 100, 102, AG


107

Replace - Ž - 100, 102,


107

Overhaul - Ž -

0904.1 Deleted

0905 Main Generator Inspect - Ž -

Test - Ž - 102, 110 P


T99.2

Replace - Ž - 100, 102,


107

Repair - Ž - 102, 110 P

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-46
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0906 Deleted

0907 Starter Generator Inspect - Ž -

Test - Ž - 102,110 P
T99.2
Replace - Ž - 100,102
107

Repair - Ž - 102,110 P
T99.2

B-47
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER. UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0909 Inverters Inspect - Ž -

Adjust - Ž - 100,102
107

Replace - Ž - 100,102
107

Repair - Ž - 102,110 R

0910 A.C. Transformer Inspect - Ž -

Replace - Ž - 100,102
107

Repair - Ž - 100,102
107

0911 Lights

0911 Navigational, Inspect - Ž -


01 Instrument,
Interior Cabin, Test - Ž - 100,102
and Anti-collision 107
Replace - Ž - 100,102
107

Repair - Ž - 100,102
107

0911 Flasher Unit Inspect - Ž -


02
Test - Ž - 100,102,
107
Replace - Ž - 100,102
107

Repair - Ž - 100,102
107

B-48
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

0911 Search Light Inspect - Ž -


03 Assembly

Test - Ž - 100, 102,


107
Replace - Ž - 100, 102,
107
Repair - Ž - 100, 102,
107
Overhaul - Ž -

0911 Landing Light Inspect - Ž -


04 Assembly

Test - Ž -

Replace - Ž - 100,102,107

Repair - Ž - 102,110

0912 Control Panels Inspect - Ž -

Replace - Ž - 100, 102,


107
Repair - Ž -
100, 102,
107
0913 Caution Panels Inspect - Ž -

Replace - Ž - 100, 102,


107
Repair - Ž - 100, 102, AI
107
- Ž - 102, 110
0914 RPM Warning Control Inspect - Ž -
Box Test - Ž -
Adjust - Ž -

Replace - Ž - 100, 102,


107
Repair - Ž - 100, 102, A l
107
Overhaul - Ž -

B-49
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS
0915 Chip Detector Inspect - Ž -
System
Replace - Ž - 100, 102,
107

Repair - Ž - 100, 102,


107
0916 Elector-Mechanical Inspect - Ž - EH-1H
Linear Actuator Only
Replace - Ž - 109, 102,
107

Repair - Ž - 00, 102,


107

Overhaul - Ž -

0917 Alternator, 30 KVA Inspect - Ž - EH-1H


Only

Test - Ž - 102, 110 P

Replace - Ž - 100, 102,


107

Overhaul - Ž -

1000 Fuel Systems Test - Ž - Q

1001 Pump, Submerged Inspect - Ž -


Fuel Booster
Test - Ž -

Replace - Ž - 102, 100

Repair - Ž - 102, 100

Overhaul - Ž -

B-50
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1002 Hoses and Tubing Inspect - Ž -

Replace - Ž - 102, 100

1003 Adapters and Inspect - Ž -


Fittings
Replace - Ž - 102, 100

1004 Valve, Safety Relief Inspect - Ž -

Replace - Ž - 102, 100

B-50.1/(B-50.2 Blank)
218-261 0 - 88 -3
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1005 Cock, Drain Inspect - Ž -

Replace - Ž - 102, 100

1006 Valve, Check Inspect - Ž -

Replace - Ž - 102, 100

1007 Filter Assembly Inspect - Ž -

Replace - Ž - 102, 100

Repair - Ž - 102, 100

1008 Valve, Gate Inspect - Ž -

Test - Ž - 102, 100

Replace - Ž - 102, 100

Overhaul - Ž -

1009 Valve, Manifold Inspect - Ž -

Replace - Ž - 102, 100

Overhaul - Ž -

1010 Transmitter, Inspect - Ž -


Pressure
Replace - Ž - 102, 100

1011 Crossover Assemblies Inspect - Ž -

Replace - Ž - 102, 100

Repair - Ž - 102, 100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-51
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1012 Cap and Adapter Inspect - Ž -


Assy
Replace - Ž - 102, 100

Repair - Ž - 102, 100

1013 Transmitter, Fuel Inspect - Ž -


Probe
Replace - Ž - 102, 100

1014 Switch Assembly, Inspect - Ž -


Float
Test - Ž - 100,102

Replace - Ž - 102, 100

1015 Tanks, Main Fuel, Inspect - Ž -


Both Crashworthy
and Non-Crashworthy

Replace - Ž - 102,101 AK

Repair - Ž - 102 AG

1015 Deleted

1016 Cross Fitting Assy Inspect - Ž -

Replace - Ž - 102, 100

1017 Pump Assy, Ejector Inspect - Ž -

Replace - Ž - 102, 100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-52
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
( 1 ) (3) (4) (5) (6)
(2) MAINTENANCE CATEGORY TOOLS
Group
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1018 Valve, Flapper Inspect - Ž -

Replace - Ž - 102, 100

1019 Plates, Flapper Inspect - Ž -


Valve
Replace - Ž - 102, 100

1020 Sump Assembly Inspect - Ž -

Replace - Ž - 102, 100

Repair - Ž - 102, 100

1021 Tank Assembly, Inspect - Ž -


Auxiliary t Internal,
Both Crashworthy Service - Ž -
and Non-Crashworthy
Install - Ž - 102, 100

Replace - Ž - 102, 100

Repair - Ž - 102, 100

Overhaul - Ž -

1021 Pump, Booster Inspect - Ž -


01
Replace - Ž - 102, 100

Repair - Ž - 102,

1022 Tank Assembly, Inspect - Ž -


Auxiliary, External
Service - Ž - 102, 100

Replace - Ž - 102, 100

B-53
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

Refuel, Receptacle, Inspect - Ž - 100, 102


1023
Closed Circuit Repair - Ž - 102
Repair - Ž - 100, 102
Repair - Ž -

1100 Flight Controls


System

1101 Main Rotor Control Inspect - Ž -


Tubes, Links and
Rod Ends Adjust - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1102 Flight Control Inspect - Ž -


Bearings
Replace - Ž - 102,112

1103 Cyclic Control


System

1103 Stick Inspect - Ž -


01
Adjust - Ž - T32, 101,
102
AK
Replace - Ž - T32, 101,
102

Repair - Ž - T32, 101,


102

B-54
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1103 Tube and Lever Inspect - Ž -


02 Assembly
Align - Ž - 100, 102,

Replace - Ž - 100, 102,

Repair - Ž - T87, 100,


102,

1103 Magnetic Brake Inspect - Ž -


03
Adjust - Ž - 100, 102,

Replace - Ž - 100, 102,


Repair - Ž -

- Ž - AN
Overhaul
1103 Force Gradient Inspect - Ž -
04
Adjust - Ž - 100, 102,

Replace - Ž - 100, 102,

Repair - Ž - 102, 112,


118

1103 Mixing Lever Inspect - Ž -


05 Assembly
Replace - Ž - 100, 102,

Repair - Ž - 100, 102,

1103 Tubes, Links and Inspect - Ž -


06 Clevises
Replace - Ž - 100, 102,

Repair - Ž - 102, 112,


118

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-55
TM 55-1520-210-23-3

B-56 Change 8
TM 55-1520-210-23-3

Change 8 B-57
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILlTY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1105 Bellcranks, Levers Inspect - Ž -


02 and Supports
Replace - Ž - 100,102

Repair - Ž - 102,112
118,120

1106 Tail Rotor Control


System

1106 Control Cables Inspect - Ž -


01
Replace - Ž - 100,102

Repair - Ž - 101,102

1106 Adjustor Assembly Inspect - Ž -


02
Replace - Ž - 101,102

Repair - Ž - 102,112
118

1106 Control Pulleys Inspect - Ž -


03
Replace - Ž - 100,102

1106 Control Quadrant Inspect - Ž -


04
Replace - Ž - 100,102

Repair - Ž - 100,102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-58
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1106 Rod and Quill Inspect - Ž -


05
Replace - Ž - 100,102

Repair - Ž - T43, 102


112,118
120

1106 Force Gradient Inspect - Ž -


07
Adjust - Ž - 100,102

Replace - Ž - 100,102

Repair 102,112
118

1106 Control Tubes Inspect - Ž -


08
Replace - Ž - 100,102

Repair - Ž - - Ž - 100,102

1106 Bellcranks, Levers, Inspect - Ž -


09 and Supports
Replace - Ž - 100,102

Repair - Ž - 112,118
120

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-59
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1106 Control Chain Inspect - Ž -


09 (Roller Type)
Adjust - Ž - 100,102

Replace - Ž - 100,102

Repair - Ž - 100,102

1200 Utility Systems

1201 Mirror Assembly Inspect - Ž -

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1202 Windshield Wiper


Assembly

1202 Blade and Arm Inspect - Ž -


01
Replace - Ž - 102,100

1202 Motor and Converter Inspect - Ž -


02 Assembly
Adjust - Ž - 100,102

1202 Motor Assembly Inspect - Ž -


02
01 Replace - Ž - 102,100

Repair - Ž - 102,100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-60
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(2) (3) (4) (5) (6)
(1)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1202 Converter Assy Inspect - Ž -


02
02 Replace - Ž - 102,100

Repair - Ž - 102,100

1202 Headguard Inspect - Ž -


02
03 Replace - Ž - 102,100

1203 Detection System, Inspect - Ž -


Fire
Test - Ž - 100,102

1203 Wiring Inspect - Ž -


01
Replace - Ž - 102,100

1203 Fire Detector Inspect - Ž -


02 Control Box
Replace - Ž - 102,100

1300 Environmental Control


Systems

1301 Distribution System, Test - Ž - 100,102 Q


Bleed Air

1301 Hoses, Tubing, Inspect - Ž -


01 Ducts
Replace - Ž - 100,102

1301 Registers and Inspect - Ž -


02 Nozzles
Replace - Ž - 100,102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-61
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1301 Valve Assy, Heating Inspect - Ž -


03 Selector
Replace - Ž - 102, 100

Repair - Ž - 102, 100

1301 Thermostatic Switch Inspect - Ž -


04
Replace - Ž - 102, 100

1301 Valve Assy, Mixing Inspect - Ž -


05
Replace - Ž - 102, 100

Overhaul - Ž -

1301 Valve, Air Inspect - Ž -


06 Distribution
Replace - Ž - 102, 100

Overhaul - Ž -

1302 Auxiliary Exhaust Install - Ž - 102, 100


Heater System (Muff)

1302 Heat Exchanger Inspect - Ž -


01
Test - Ž -

Replace - Ž - 102, 100

Repair - Ž - 102, 100

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-62
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)

NOMENCLATURE OF END ITEMS


HELlCOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H

(1) (2) (3) (4) (5) (6)


GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1302 Hoses, Tubing, Inspect - Ž -


02 Ducts
Replace - Ž - 102, 100,

1302 Blower Unit Inspect - Ž -


03
Replace - Ž - 102, 100

Repair - Ž - 102, 100 M


- Ž - 102, 112

1302 Valve, Mixing Inspect - Ž -


04
Replace - Ž - 102, 100

Repair - Ž - 102, 100 M


- Ž - 102, 112

1302 Plenum Assembly Inspect - Ž -


05
Replace - Ž - 102, 100

Repair - Ž - 102, 100 M


- Ž - 102, 112

1302 Switch, Overheat Inspect - Ž -


06
- Ž - 102, 100
Replace

SAV-HQ Form 19 Edition of 1 Jul 76, IS obsolete


1 Apr. 77

Change 5 B-63
TM 55-1520-210-23.3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)

NOMENCLATURE OF END ITEMS


HELlCOPTER UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH -1H

(1) (2) (3) (4) (5) (6)


GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1400 Hoist and Winches

1401 Rescue Hoist Inspect - Ž -


Assembly
Test - Ž -

Service - Ž - 100, 102,


107

Install - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 100, 102,


107
- Ž - 102, 110
Overhaul - Ž -

1401 Post and Locknut Inspect - Ž -


01
Replace - Ž - 100, 102,

Repair - Ž - 100, 102,

1401 Hoist Cable Inspect - Ž -


02
Replace - Ž - T5, 100,
102

1401 Guillotine and Inspect - Ž -


03 support
Replace - Ž - 100, 102

Repair - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, IS obsolete


1 Apr 77

B-64
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L TRANSPORT UH-1H/UH-lV/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARK:

1401 Guide Tube Inspect - Ž -


04

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1401 Boom Inspect - Ž -


05

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1401 Trigger Assembly Inspect - Ž -


06

Replace - Ž - 100, 102,


107

Repair - Ž - 100, 102,


107

1401 Side Plates Inspect - Ž -


07 and Roller

Replace - Ž - 100, 102

Repair - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-65
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1401 Limit Switches Inspect - Ž -


08
Adjust - Ž - 100, 102,
107

Replace - Ž - 100, 102,


107

Repair - Ž - 100, 102,


107

1401 Overload Sensing Inspect - Ž -


09 Relay

Replace - Ž - 100, 102,


,107

Repair - Ž - 100, 102,


107

1401 Hook and Bumper Inspect - Ž -


10 Assembly

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1401 Adapters Inspect - Ž -


11

Replace - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-66
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1401 Power Cables Inspect - Ž -


12

Replace - Ž - 100, 102,


107

Repair - Ž - 100, 102,


107

1401 Control Box Inspect - Ž -


13
Test - Ž - 102, 110,
118

Replace - Ž - 102, 110,


118

Repair - Ž - 102, 110,


118

Overhaul - Ž -

1401 Control Pendant Inspect - Ž -


14
Test - Ž - 102, 110

Replace - Ž - 102, 110,


118,120

Repair - Ž - 102, 118,


120

Overhaul - Ž -
SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete
1 Apr 77
B-67
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1401 Hoist Drive Unit Inspect - Ž -


15
Test - Ž -

Replace - Ž - 100, 102,


107

Repair - Ž - 102, 110,


112, 118

Overhaul - Ž -

1401 Hoist Cable Inspect - Ž -


16 Storage Drum
Test - Ž -

Replace - Ž - 100, 102,


110
Repair - Ž - 102, 110,
112, 120,
119

1401 Rubber Pressure Inspect - Ž -


17 Roller

Replace - Ž - 100, 102

Repair - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-68
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1401 Actuator and Inspect - Ž -


18 Lever

Replace - Ž - 100,102

Repair - Ž - 100,102

Overhaul - Ž -

1401 Lower Post Inspect - Ž -


19 Support

Replace - Ž - 100,102

Repair - Ž - 100,102

1402 Cargo Suspension


System

1402 Cargo Suspension Inspect - Ž -


01 Assembly
Test - Ž -

Service - Ž - 100,102

Adjust - Ž - 100, 102

Install - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, IS obsolete


1 Apr 77

B-69
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1402 Release Cables Inspect - Ž -


02
Install - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1402 Pedal Assembly Inspect - Ž -


03
Install - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 100, 102

1402 Cargo Hook Inspect - Ž -


04
Service - Ž - 100, 102

Adjust - Ž - 100, 102

Install - Ž - 100, 102

Replace - Ž - 100, 102

Repair - Ž - 102, 112,


118, 120

1600 Mission Equipment


1601 Smoke Generator Inspect - Ž -
Subsystem
Servlce - Ž -

Install - Ž -
102,100
Replace - Ž - 102,100

PAGES B-70.1 THROUGH B-70.8 HAVE BEEN DELETED.

B-70 Change 4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTIILITY-TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE TOOLS
FUNCTION AND REMARKS
NUMBER
AVUM AVIM DEPOT EQUIPMENT

1403 Rescue Hoist Assembly, Inspect


High Performance
Test 107

Service 100, 102


Install 101,102

Replace 101,102
Repair 100, 102,
107

1403 Winch Assembly Repair


01 118
Overhaul
Inspect 107, 102
T3
Test 00, 102

Service
Replace
101, 102
Repair 107
101,102
107,110
Overhaul

1403 Limit Switch Drive Inspect


Assembly
01 Adjust 101,102

Replace 101,102

Repair 101,102
107,T3

Test 110

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete.


1 Apr 77
B-70.1
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMECLATURE OF END ITEMS
HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE
NUMBER FUNCTION TOOLS REMARKS
AND
AVUM AVIM DEPOT EQUIPMENT

1403 Switches and Connector Inspect - Ž -


01
01 Replace - Ž - 101,102

1403 Motor Assembly Inspect - Ž -


01 - Ž - - Ž - 110
Test
02 Repair - Ž - 107, T3 AO
Replace - Ž - 101,102
107
Overhaul - Ž -

1403 Brake Assembly Inspect - Ž -


01
03 Test 101, 102
107

Replace - Ž - 101, 102


107
Overhaul - Ž -

1403 Chain Inspect - Ž -


01
04 Adjust - Ž - 101,102
101,102
Replace - Ž -

1403 Cable Hook Assembly Inspect - Ž -


01
05 Service - Ž - 100, 102

Replace - Ž - 101,102

Repair - Ž - 101,102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete.


1 Apr 77
B-70.2
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10
NOMENCLATURE OF END ITEMS
HELlCOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE
TOOLS REMARKS
NUMBER FUNCTION AND
AVUM AVIM DEPOT EQUIPMENT

1403 Boom Assembly Inspect


02
Test 101, 102
107, T3,
Service 110
100, 102
Adjust 101, 102
107
Align 101, 102
107

Repair 101, 102


107
Replace

Test
1403 Up Limit Actuator Inspect
02
101, 102
01
107
101, 102
107
Replace 101, 102
107
Repair 101, 102
107
1403 Cable Assembly Inspect
02
02 Replace 101, 102
107

1403 Full-Up Limit Switches Inspect


02
03 Adjust 101 102
107
Adjust 101, 102
107
Replace 101, 102
107
Repair 101, 102
107
Test 107,110
T3

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete.


1 Apr 77
B-70.3
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS

HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H


(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE
FUNCTION TOOLS REMARKS
NUMBER AND
AVUM AVIM DEPOT EQUIPMENT

1403 Post Structure/Boom Inspect - Ž -


03 Position Actuator Assy
Test - Ž - 107,101,
T3
Service - Ž - 100, 102,
Adjust - Ž - 101,102
107
Replace - Ž - 101,102
107,
Repair - Ž - 101,102
107
- Ž - 102,110
Overhaul - Ž - - Ž -
1403 Motor Inspect - Ž -
03
Test - Ž - 110,102
01
- Ž -
Replace 102.110

Repair - Ž - 102,110

Overhaul - Ž -

1403 Stanchion Inspect - Ž -


03
02 Service - Ž - 100,102

Replace - Ž - 100, 102,

Repair - Ž - - Ž - 102, 110


118, 101

1403 Mechanical Stop Assembly Inspect - Ž -


03
03 Adjust - Ž - 102

Replace - Ž - 102

Overhaul - Ž -

SAV-HQ Form 19 Edition of 1 Jul 76, obsolete.

B-70.4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS

HELICOPTER, UTILITY- TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H


(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE
NUMBER FUNCTION TOOLS REMARKS
AND
AVUM AVIM DEPOT EQUIPMENT

1403 Rotary Actuator Assy Inspect - Ž -


03
04 Test - Ž - 110
Replace - Ž - 102,110
Repair - Ž - 102, 110

1403 Reaction Arm Assembly Inspect - Ž -


03
05 Service - Ž - 100,102

Overhaul, - Ž - - Ž - 102
Replace - Ž - 101,102

Repair - Ž - 101,102

1403 Limit Switches Inspect - Ž -


03
06 Adjust - Ž - 107,101

Replace - Ž - 101,102
107
Repair - Ž - 101,102
107

1403 Inertia Dump Assembly Inspect - Ž -


03
07 Adjust - Ž - 102,110

Replace - Ž - 102,110

Repair - Ž - 102,110

1403 Stanchion, Upper Inspect - Ž -


03
08 Service - Ž - 100,102

Replace - Ž - 101,102

Repair - Ž - 102
SAV-HQ Form 19 Edition of 1 Jul 76, obsolete.
1 Apr 77
B-70.5
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY MAINTENANCE
FUNCTION TOOLS REMARKS
NUMBER AND
AVUM AVIM DEPOT EQUIPMENT

1403 Control Panel Inspect - Ž -


04
Test - Ž -
110

Replace - Ž - 101,102,
107
Repair - Ž - 101,102,
107
- Ž - 102,110
Overhaul - Ž -
1403 Cables Inspect - Ž -
04
01 Replace - Ž - 107,101,
102
Repair - Ž - 107,101,
102
1403 Lamps Inspect - Ž -
04
02 Replace - Ž - 101,102

1403 Control Pendant Inspect - Ž -


05
Test - Ž - 107

Replace - Ž - 101,102,
107
Repair - Ž - 101,102,
107
Overhaul - Ž -

1403 Indicator Lamp Inspect - Ž -


05
01 Replace - Ž - 100, 102

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete.


1 Apr 77
B-70.6
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


( A V S C O M Reg 310-10)

NOMENCLATURE OF END ITEMS


HELICOPTER, UTILITY - TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE MAINTENANCE CATEGORY
COMPONENT/ASSEMBLY TOOLS REMARKS
NUMBER FUNCTION ANO
AVUM AVIM DEPOT EQUIPMENT

1600 Mission Equipment

1601 Smoke Generator Inspect - Ž -


Subsystem
Service - Ž -

Install - Ž - 102,100

Replace - Ž - 102,100

Edition of 1 Jul 76, iS obsolete.

6-70.7/(6-70.8 blank)
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1602 Curtain Assy, Inspect - Ž -


Blackout
Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1603 Paratroop Static Inspect - Ž -


Line
Install - Ž - 102,100

Replace - Ž - 102,100

1604 Support Assy, Inspect - Ž -


External Stores
Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1605 Heat Suppression Inspect - Ž -


(IR)
Install - Ž -

Replace - Ž - 102,100

Repair - Ž - 102,100

1606 Litter Racks Inspect - Ž - UH-1V


only

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77

B-71
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS
1606 Strap Assy, Inspect - Ž - UH-1V
01 Support only

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1606 Support Inspect - Ž - UH-1V


02 only

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1606 Belts Inspect - Ž - UH-1V


03 only

Install - Ž - 102,100

Replace - Ž - 102,100

1607 Pylon Assembly, Inspect - Ž -


External Stores
Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1608 Armament Subsystem, Inspect - Ž -


M60C
Install - Ž - 102,100

Replace - Ž - 102, 100

Repair - Ž - S

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-72
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
UMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1609 Rack, External Inspect - Ž -


Stores
Install - Ž - 102,100

Replace - Ž - 102,100

Overhaul - Ž -

1610 Armament Subsystem, Inspect - Ž -


M56
Adjust - Ž -

Align - Ž -

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1610 Manual Jettison, Inspect - Ž -


01 External
Adjust - Ž -

Align - Ž -

Replace - Ž - 102,100

1610 Tube Assy, Inspect - Ž -


02 Strut

Replace - Ž - 102,100

Repair - Ž - 102,100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-73
218-261 0 - 88 -4
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – TACTICAL TRANSPORT UH-1H/UH-1V/EH-1H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT/ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1610 Damper Assembly Inspect - Ž -


02
01 Adjust - Ž -

Replace - Ž - 102,100

1610 Dispenser, Control Inspect - Ž -


03 Panel

Replace - Ž - 102,100

Repair - Ž - T

1611 Armament Subsystem, Inspect - Ž -


M23

Replace - Ž - 102,100

Repair - Ž - U

1611 Mount Assembly Inspect - Ž -


01

Replace - Ž - 102,100

Repair - Ž - 102,100

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-74
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

Inspect - Ž - UH-1V
1612 Blood Bottle Hooks
only
Replace - Ž - 102,T100

1613 Armament Subsystem Inspect - Ž - EH-1HX


M130 only
Install - Ž - 102,T100

Replace - Ž - 100,102

Repair - Ž - 100,102

1700 Emergency Equipment

1701 First Aid Kit Inspect - Ž -

Replace - Ž - 102,100

Repair - Ž - W

1702 Fire Extinguisher Inspect - Ž -

Replace - Ž - 102,100

Repair - Ž - X

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-75
TM 55-1520-210-23-3

MAINTENANCE ALLOCATION CHART


(AVSCOM Reg 310-10)
NOMENCLATURE OF END ITEMS
HELICOPTER, UTILITY – T A C T I C A L T R A N S P O R T U H - 1 H / U H - 1 V / E H - 1 H
(1) (2) (3) (4) (5) (6)
GROUP MAINTENANCE CATEGORY TOOLS
MAINTENANCE AND
NUMBER COMPONENT ASSEMBLY FUNCTION AVUM AVIM DEPOT EQUIPMENT REMARKS

1702 Bracket Inspect - Ž -


01
Replace - Ž - 102,100

1703 Jettison System, Inspect - Ž -


Internal, External
Stores Adjust - Ž -

Install - Ž - 102,100

Replace - Ž - 102,100

Repair - Ž - 102,100

1800 Installed Avionics R


Components

SAV-HQ Form 19 Edition of 1 Jul 76, is obsolete


1 Apr 77
B-76
TM 55-1520-210-23-3

SECTION III. TOOL AND TEST EQUIPMENT REQUIREMENTS

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NO.
REFERENCE CODE

T1 o Adapter, Balancing 4920-00-168-9797 AA4920-8503

T2 0 Attachment Set, Spanner SKO AN8515

T3 0 Multi meter Toe AN/URM-105C


T3.1 0 Tester Exhaust Gas TMDE BH112JA-53
T4 0 Blind Bolt or Nut 5120-00-733-7119 BH120-1032M3
T5 0 Wrench, Spline BL-6529

T7 0 Meter, Frequency JTB Model


33FS

T8 Deleted

T9 Deleted

T10 Deleted
T10.1 F Tester, PRESSURE 6685-00-693-5009 MP1
T11 o Wrench, Power SKO PD1201

T12 0 Socket, Mast Nut 5 1 2 0 - 0 0 - 6 1 9 - 9 7 7 9 PD2659

T13 Adapter, Reaction 5 1 2 0 - 0 0 - 6 1 9 - 9 7 7 9 PD2660

T14 0 Replaced by T11

T15 F Plate, Anchor 4920-00-713-1366 SWE124330


replaced by
F Socket, Splined 5120-00-619-9774 PD2657

T16 F Socket, Splined 5120-00-619-9773 PD2658

T17 o Adapter Arm, Engine SKO SWE13852-1210

T19 0 Transmission Adapter 4290-00-676-2307 SWE123852-40

T20 F Adapter SWE13852-500

T21 o Stand, Maintenance SWE13855


T21.1 0 Mobil Engine Test Unit TMDE TE12062
T22 0 Sling, Aircraft, 1730-00-099-8099 T100220
Maintenance

Change 4 B-77
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NUMBER
REFERENCE CODE

T23 F Fixture TI00615-13LW

T24 F Installing tool, 5120-00-150-7346 T555-7


seal

T25 F Fixture, Holding 4920-01-037-7105 T205-076-099-2

T26 F Thumbscrew Set 5305-00-765-4469 T100929

T27 F Same as T16

F Same as T16

T28 F Adapter 5130-00-676-1681 T101304


replaced by
F Socket, Splined 5120-00-619-9774 PD2657
T28.1 Wrench, Transmission 4920 -00-737- T101305
6435
T29 o Wrench, 4920-00-797-3672 T101306
Transmission
T30 0 Wrench, Tail 4920-00-718-6533 T101307
Rotor

T31 0 Jack Screw Set 4920-00-710-7946 T101308

T32 0 Rigging Fixture 1730-00-678-5412 T101330

T33 0 Jack Screw Set 4920-00-765-4410 T101338

T34 0 Build-up Bench 4920-00-678-5431 T101356

T35 0 Fixture, Holding 4920-00-474-0569 T101365

T36 F Support, Scissors 4920-00-786-1756 T101369

T37 F Ram, Adapter, 4920-00-713-5555 T101382


Scissors

T38 F Socket, Wrench, 5120-01-033-5410 PD1469


Face 5120-00-033-5090 PD1470
5120-00-033-2112 PD1471

T39 o Support, Rotor Adj. 4920-00-718-6677 T101400

T40 0 Scope Assy, Blade 4920-00-718-6674 T101401

B-78
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NO.
REFERENCE CODE

T41 o Link, Grip Positioning 4920-00-718-6673 T101402

T42 o Plate, Yoke Bearing 4920-00-718-6666 T101406

T43 o Seal & Bearing Tool 4920-00-793-2134 T101407

T44 F Tool, Build-up 4920-00-251-2509 T101412


replaced by
o Tool, Grip Spacing 4920-00-251-2509 T101457

T45 0 Socket, Wrench 5120-00-044-1426 T101414

T46 0 Hoist Assembly 4920-00-996-0860 T101416


replaced by
0 Hoisting Unit, Engine 1730-00-073-9258 T101452

T47 0 Tool Set, Align 5120-00-894-6540 T101419

T48 0 Fixture, Holding 4920-00-876-0103 T101420

T49 0 Plate 4920-00-898-0015 T101421

T50 0 Bar, Bearing Removal 4920-00-876-0102 T101424

T51 0 Jack Set 4920-00-805-5123 T101440

T52 0 Socket, Wrench, Face 5120-00-967-7699 T101449

T53 0 Same as T46

T54 0 Jaw, Puller 5120-00-996-3942 T101455

T55 0 Wrench 5120-00-018-0220 T101456

T56 0 Tool, Grip Spacing 4920-00-251-2509 T101457

T56.1 0 Bending Gage, M/R 5210-00-919-2374 T101485


Blade Trim Tab

T56.2 0 Stop, Flap 5210-00-924-7756 T101468

T56.3 0 Support,M/R 4920-00-907-7649 T101467

T56.5 F Grip Spacing Tool 5220-00-907-7024 T101474

B-79
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NUMBER
REFERENCE CODE

T56.6 F Bearing Removal Tool 5120-00-907-4889 T101475

T56.7 F Installing Tool 5120-00-925-5085 T101487

T57 O Wrench, Input Quill 5120-00-932-3670 T101488

T57.1 F Bearing Puller 5120-00-999-5306 T101491

T58 Same As T38

Same As T38

T58.1 Same As T38

T59 0 Gage, Grip Spacing 5120-00-182-3779 T101559

T59.1 F Installing Tool 5120-00-407-7330 T101586

T60 o Wrench, Spanner 5120-00-421-7401 T101600

T61 Deleted

T61.1 0 Lock, M/R 5120-00-451-2956 T101864

T62 0 Positioning Tool 5120-00-477-0874 T101865

T62.1 F Fixture, Torque 4920-00-491-3559 T41000310-1

T63 F Adapter, Torque Wrench 5120-00-480-7728 T41000870-1

T64 O Wrench, Windshield 5120-00-076-4380 XW20509

T65 Cable, Extension To Be Fabricated 1560-UH1-772-1

T66 Cable, Jumper To Be Fabricated 1560-UH1-772-2

T67 Wrench, Spanner 204-076-202-100B

T68 Bridge, Automatic, To Be Fabricated 387011


(Simmonds) Capacitance

T69 Field Calibration 387991-003

T70 O Maintenance Stand SKO 4920-EG-008

T71 Same As T70

T72 F Wrench, Adapter 67SP1275-011

T72.1 F Installing Tool 5120-00-114-1176 68SAVAED0221

B-80 Change 5
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NUMBER
REFERENCE CODE

T73 O Kit Balancing TMDE 7A050

T74 O Wrench, Spanner 7FA18005-50

T75 O Use T75.1, T75.2, T75.3, 7HEL053


T75.4

T75.1 O Fixture, Support 4920-00-708-3113 2532

T75.2 O Bushing 4920-00-868-8441 2533

T75.3 O Bushing 4920-00-708-3115 2529

T75.4 O Arbor 4920-00-708-3084 2516

T76 O Use T76.1 and T76.2 7HEL054

T76.1 0 Sleeve, Rotor Hub 4920-00-708-3089 2467

T76.2 0 Fixture, Rotor Hub 4920-00-708-3063 2337

T77 F Tool Kit Blade Bal 4920-00-856-8214 7HEL061

T78 O Adapter, Bal 4920-00-937-9418 7HEL065


replaced by
T78 0 Adapter, Bal 4920-00-168-9797 AA4920-8503

T78.1 0 Clevis Assy, Lifting 204-011-178-1

T78.2 0 Adapter, Bal 4920-00-924-5708 7HEL066

T79 0 Spacer 2201

T80 0 Wheel, Hand 2215

T81 0 Arbor, Balancing 2259

T82 Fixture, Rotor Blade SKO 2337

T83 F Sleeve, Rotor Hub 4920-00-708-3089 2467

T84 C/O 7HEL061 and 2486


7HEL066

T85 O Plate, Blade SKO 2586

T86 0 Adapter C/O 7HEL061 4920-00-536-8218 2588

Change 5 B-81
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NUMBER
REFERENCE CODE

T86.1 O Torque Fixture 205-076-099-2

T87 O Reamer 27872-2&11

T88 O Hydraulic Test Stand TMDE D-5A

T89 Fixture, Centering 4920-00-176-4258 205-200-005


1AAT-1

T90 Fixture Locating 4920-00-159-8680 71SAVAE-D


and Drilling 0009

T91 Thermometer Tester NA-2


Electric Field Type

T92 Socket SWE126377

T93 Anchor Plate SWE124387

T94 Torque Multiplier SWE103

T95 Ratchet Adapter SWE67

T96 O Work Handle SKO SWE63

T97 Torque Wrench SWE54

T98 O Propeller Protractor 5520-00-212-8747 36D2844

T99.1 F Tool Kit, Bearing Staking 5180-00-091-8678 T101873

T99.2 F Test Stand Acft. Gen. 4920-00-697-9969 7199


O
100 Tool Set, AVUM, 4920-00-159-8727
Set No. 1

101 0 Tool Set, AVUM, 4920-00-567-0476


Set No. 2

102 O Tool Kit, Aircraft 5180-00-323-4676


Mechanics, General

103 O Tool Kit, Airframe 5180-00-323-4876


Repairman

104 O Tool Kit, Hydraulic 5180-00-323-4891


Repairman

B-82 Change 5
TM 55-1520-210-23-3

TOOL OR TEST MAINTENANCE NOMENCLATURE NATIONAL TOOL NO.


EQUIPMENT CATEGORY STOCK NUMBER
REFERENCE CODE

106 0 Tool Kit, Instrument 5180-00-323-


Repairmans 4913

107 0 Tool Kit, Electrical 5180-00-323-


Repairmans 4915
108 0 Tool Kit, Eng Repair- 5180-00-323-4944
mans

109 0 Tool Kit, Power Train 5180-00-003-5267

110 F Shop Set, AVIM, Electri- 4920-00-165-1453


cal-lnstrument

111 F Shop Set, AVIM, Hydraulic 4920-00-165-1454

112 F Shop Set, AVIM, Machine 4920-00-405-9279


Shop

113 F Shop Set, AVIM, Power 4920-00-001-4132


Train

114 F Shop Set, AVIM, Propeller 4920-00-224-3681


Suppl

115 F Shop Set, AVIM, Recip 4920-00-464-0222


Eng, Suppl

116 F Shop Set, AVIM, Rotor 4920-00-405-9270


Shop

117 F Shop Set, AVIM, Sheet 4920-00-166-5505


Metal

118 F Shop Set, AVIM, Tool 4920-00-472-4183


Crib

119 F Shop Set, AVIM, Turbine 4920-00-224-3684


Engine

120 F Shop Set, AVIM, Welding 4920-00-163-5093

121 F Scales Set, Aircraft 6670-00-148-9395


Weighing

B-83
TM 55-1520-210-23-3

SECTION IV

REMARKS

REFERENCE CODE REMARK

A. Limited to Airframe Repairman Tool Kit and Portable Hand Tools.

B. Not including build-up.

C. Limited to Epoxy Minor Repair

D. Limited to Nicks and Scratches

E Provided Replacement Fixtures/Tools are utilized and personnel have been trained in
proper usage of these fixtures

F. Not requiring Jigs and Fixtures.

G. Refer to TM 55-2840-229-23.

H. Mets Stand

I. Limited to Dust Boot or Shield.

J. Limited to Replacement of Packings.

K. Balance

L. Track

M. Limited to Replacement of External Components and External Surface Repair only.

N. Timing

O. Refer to TM 11-6140-203-14-2.

P. Based on Distribution of Generator Test Stand.

Q. Troubleshooting System

R. Refer to TM 11-1520-210-20, contains Maintenance Instructions for Avionics.

S. Refer to TM 9-1005-243-12.

T. Refer to TM 9-1345-201-10-1.

U. Refer to TM 9-1005-262-14

V. Refer to TM 9-1005-262-15

W By Station Medical Supply Office.

B-84
TM 55-1520-210-23-3

REFERENCE CODE REMARK

X. Should be recharged by authorized personnel.

Y. Excluding the Replacement of Sleeves. UH-18/M

Z. Limited to Replacement of Rod End Bearing.

AA. Refer to TM 9-1340-223-34.

AB. Refer to TM 9-1010-207-12 and TM 9-1010-207-34.

AC. Refer to TM 9-1005-243-12.

AD. Refer to TM 9-1400-461-20 and TM 9-1400-461-35.

AE. Refer to TM 9-1090-201-12.

AF. Refer to TM 3-6665-267-12 and TM 3-6665-267-35.

AG. Refer to TM 55-1500-204-25/1.

AH. Welding.

AI. Bulb Replacement only.

AJ. Not used.

AK. Restricted to AVUM units with 10 or more aircraft. Use extreme care in removal and/
or repair.

AL. If electronic test is required, accomplish with AVIM support.

AN. Restricted to Non-Divisional Repair.

B-85
TM 55-1520-210-23-3

APPENDIX C

AIRCRAFT INVENTORY MASTER GUIDE

C-1. INTRODUCTION (2) Loose equipment delivered with the aircraft


and items subject to pilferage or readily converted to
C-2. Scope. Figures C-1 and C-2 list those items of personal use.
installed or loose equipment required by and authorized for
using organizations to accomplish their primary or alternate (3) Modification kits which am issued or
mission. This list will serve to standardize present inventory distributed to using organizations for installation and which
procedures, using the inventory master guide to determine are not immediately placed m work will be recorded on the
the inventoriable items of installed and loose equipment. affected aircraft’s DA Form 2408-17 (Aircraft Inventory
Insofar as possible, items of equipment are listed m the Record) and identified as loose equipment until
sequence of their physical location within the aircraft area. modification is completed.

NOTE (4) Equipment required for operation in special


environment.
Reference Figure C-2 for items added b. [terns to be excluded
or replaced as a result of MWO 55-
1520-210-50-13 through MWO 55- (1) Nonaccountable items code as expendable in
1520-210-50-23. the applicable stock lists.

C-3. Changes to Inventory. Aircraft inventory is (2) Personal issue or furnished on unit
subject to change as a result of authorized changes allowance or other authority.
(MWO’s), addition or deletions of property for special
missions requirements; therefore, the selection of items of (3) Items or components considered as basic or
inventory from the inventory master guide may or may not integral parts of the aircraft or basic aircraft such as
provide a complete inventory list. When it is known that the engines, propellers, wheels and standard instruments.
master guide does not provide a complete inventory list it
will be necessary to research authorized changes (MWO’s) (4) Equipment publications, check lists, and
and local command directives in order to compile an aircraft forms.
accurate and exact inventory list
C-8. Periods of Inventory. Inventoriable items will
C-4. Inventory Forms and Records. Refer to DA be checked against the Aircraft Inventory Record (DA Form
PAM 738-751 for applicable forms and records. 2408-17) at the following periods:

C-5. REQUIREMENTS. a. Upon receipt of the aircraft.

C-6. Security. It is desired that inventory records be b. Prior to transfer of the aircraft to another
unclassified, Therefore when equipment bearing a security organization.
classification or the installation of unclassified equipment
is of a confidential or secret nature accomplishment of the c. Upon placing aircraft in storage and upon
classification will be m accordance with security removing from storage. Aircraft need not be inventoried
regulations. while m storage.

C-7. Inventoriable Items. Selection of inventoriable


items is without regard to the agency, governmental or
contractual, furnishing the items.

a. Items to be listed am:

(1) Items essential to the execution of the


designated mission of the aircraft such as electronic,
photographic, armament, special mission instruments, and
safety and comfort equipment,

Change 4 C-1
TM 55-1520-210-23-3

Figure C-1. Inventory Items List Component Diagram (Sheet 1 of 5).

C-2 Change 8
TM 55-1520-210-23-3

Figure C-1. Inventory List Component Diagram (Sheet 2 of 5).

Change 8 C-3
TM 55-1520-210-23-3

Figure C-1. Inventory Items List Component Diagram (Sheet 3 of 5).

C-4 Change 8
TM 55-1520-210-23-3

Figure C-1. Inventory Items List Component Diagram (Sheet 4 of 5).1

Change 8 C-5
TM 55-1520-210-23-3

Figure C-1. Inventory Items List Component Diagram (Sheet 5 of 5).

C-6 Change 8
TM 55-1520-210-23-3

Figure C-2. UH-1H Inventory Items List Component Diagram (Sheet 1 of 4).
(With MWO 55-1520-1520-210-50-13 through MWO 55-1520-1520-210-50-23 Installed)

Change 8 C-7
TM 55-1520-210-23-3

UH-1H Aircraft Series


NOMENCLATURE and Number of Items Remarks
Normally Installed

SECTION A - NOSE COMPARTMENT (CONT’D)

COMSEC Processor and Mount KY-75 1 Use by-pass cable when


KY-75 not installed
Audio Amplifier ASK-9-03707-1 1
Recvr/Trans RT-1477/ARC-201 1 Replaces ARC-131
Mount MT-6373/ARC-201 1
GS Antenna AS-3188/ARN 1
Recvr VOR/ILS R-2023/ARN-123 1 Replaces ARN-82,
R-1963, and R-1041
Adapter Plate 1560-UH1-808 1 Mounts ARN-123
Power Supply, 5V, 156-UH1-872 1 Use with ARC-201 Elec-
troluminescent Panel
Panel Lighting Inverter, 115 VAC 1 Used for ARC-201 panel
(CSK-9-03049-1) lighting
Dimmer Network Assembly, 90197092-501 1
Power Supply, 115V 2 Inverter
Battery Box CY-()/ARC-201 1
Secure Voice Equipment TSEC/KY-58 1

SECTION B - PILOTS COMPARTMENT

Control C-10533/APX-100 1 Replaces APX-72 Control


Control Panel C-10604(V)6 1
Recvr/Trans RT-1167/ARC-164 1 Replaces AN/ARC-51
KY-75 Control TSEC/KY-75 1
HF Volume Control Assembly 1
Control Display C-11245 1
Control Panel AN/ARC-199 1
Control C-11466/ARC-201 1
Recvr/Trans RT-1476/ARC-201 1

Figure C-2. UH-1H Inventory Items List Component Diagram (Sheet 2 of 4)


(With MWO 55-1520-210-50-13 through MWO 55-1520-210-50-33 Installed)

C-8 Change 9
TM 55-1520-210-23-3

Figure C-2. UH-IH Inventory Items List Component Diagram (Sheet 3 of 4).
(With MWO 55-1520-1520-210-50-13 through MWO 55-1520-1520-210-50-23 Installed)

Change 8 C-9
TM 55-1520-210-23-3

Figure C-2. UH-1H Inventory Items List Component Diagram (Sheet 4 of 4).
(With MWO 55-1520-1520-210-50-13 through MWO 55-520-1520-210-50-23 Installed)

C-10 Change 8
TM 55-1520-210-23-3

APPENDIX D

ILLUSTRATED FIELD MANUFACTURE ITEM LIST

This appendix includes complete instructions, includ-


ing bills of material, for field manufacture (fabrication) of
all items listed in TM 55- 1520-210-23P, Aviation Unit
and Intermediate Repair Parts and Special Tools List
bearing MO or MF source code. The part number index
lists all items in part number order with a cross reference
to the figure in which the item appears. All materials
necessary for manufacture of all items are listed by
National Stock Number in the bill of material for the item.

D-1
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.


AA8621-2D12 D-351 MS 20253-2-600 D-46
AA9500-2317-0 D-413 MS 20253-2-2450 D-46
AN257-2-650 D-15 MS 20253-2-7950 D-46
AN6544 D-6 MS 20253-2-1035 D-46
AN6545 D-7 MS 20253P2-275 D-46
AN6546 D-9 MS 20253P2-387 D-46
AN6910 D-10 MS 20253P2-538 D-22
AN6915 D-14 MS 20253P2-2372 D-46
AN743-7 D-4 MS 25083-2BB5 D-303
AN743-12 D-4 MS 25083-2BB6 D-303
AN743-13 D-4 MS 27212-1-3 D-37
AN8031-8-183 D-5 MS 27212-1-9 D-37
AN9116-2 D-16 MS 27212-1-10 D-37
BL6150 D-29 MS 27212-1-12 D-37
BL8359 D-30 MS 27212-1-14 D-37
BL8379 D-229 MS 27212-1-15 D-37
BL8453 D-228 MS 27253-2 D-343
BL8456 D-227 MS 28741 D-41
BL8458 D-35 MS 8000 D-41
BL8515 D-230 MS 8001 D-41
BS-1 D-398 MS 87028 Thru D-41
BYRF572 D-52 MS 87032 D-41
B56C21 D-56 NAS 1455-00-3C D-19
B79C65 D-55 NAS 1455-00-5 D-19
CSC-536-3 D-18 NAS 1455-A-00-4 D-19
DK-1 D-401 NAS 1455-1A2-5 D-19
ES-B-220309 D-391 NAS 1455B00-5 D-19
ES-B-220311 D-390 NAS 42DD4-16 D-11
ES-B-220316 D-396 NAS 42DD6-8 D-2
ES-B-220354 D-388 NAS 43-3-8 D-2
ES-B-220355 D-387 NAS 43-3-24 D-2
ES-B-221427 D-386 NAS 43-3-42 D-2
ES-B-221566 D-385 NAS 43-3-48 D-2
ES-B-221712 D-384 NAS 43-4-12 D-2
ES-B-221720 D-375 NAS 43-4-14 D-2
ES-C-213928 D-383 NAS 43-4-44 D-2
ES-C-221355 D-372 NAS 43-4-108 D-2
ES-C-221440 D-382 NAS 43-5-36 D-2
ES-C-221569 D-381 NAS 43-5-48 D-2
ES-C-221697 D-374 NAS 43-6-12 D-2
ES-C-221709 D-380 NAS 43-6-30 D-2
ES-C-221739 D-379 NAS 43DD1-7 D-2
ES-D-221175 D-397 NAS 43DD1-16 D-2
ES-D-221672 D-389 NAS 43DD3-9 D-2
ES-F-221565 D-377 NAS 43DD3-10 D-2
ES-F-221752 D-378 NAS 43DD3-12 D-2
E1112-32-14 D-225 NAS 43DD3-19 D-2
GRHB-1 D-395 NAS 43DD3-21 D-2
GRHB-2 D-396 NAS 43DD3-22 D-2
HM-1 D-394 NAS 43DD3-23 D-2
IPS-1 D-42 NAS 43DD3-28 D-2
IPS-2 D-42 NAS 43DD3-30 D-2
MS 18029-1S11 D-242 NAS 43DD3-31 D-2
MS 18029-1S10 D-242 NAS 43DD3-36 D-2
MS 18029-1S14 D-242 NAS 43DD3-38 D-2
MS 18029-1S15 D-242 NAS 43DD3-44 D-2
MS 20253-2-225 D-46 NAS 43DD3-45 D-2
MS 20253-2-275 D-46 NAS 43DD3-48 D-2

D-2 Change 9
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.


NAS43DD3-50 D-2 YI159-2-3 D-226
NAS43DD3-53 D-2 100-057-1 D-142
NAS43DD3-54 D-2 100-057-5 D-143
NAS43DD365 D-2 100337 D-224
NAS43DD367 D-2 106324 D-410
NAS43DD3-70 D-2 110-0331 D-71
NAS43DD3-74 D-2 110-119-1 D-134
NAS43DD3-76 D-2 11021-1 D-219
NAS43DD3-80 D-2 120-069-1 D-233
NAS43DD3-88 D-2 120-067B020 D-234
NAS43DD3-92 D-2 120-067B17 D-234
NAS43DD3-96 D-2 130-005-5-2 D-232
NAS43DD3-98 D-2 130-005-6-58 D-232
NAS43DD3-112 D-2 130-005-7-4 D-232
NAS43DD4-10 D-2 130405-7-10 D-232
NAS43DD4-16 D-2 130-005-7-50 D-232
NAS43DD4-23 D-2 130-005-7C4 D-232
NAS43DD4-28 D-2 130-005-84 D-232
NAS43DD4-38 D-2 130-005-96 D-232
NAS43DD4-60 D-2 1560-UH1 D-395
NAS43DD461 D-2 1560-UH1-711-1 D-363
NAS43DD4-71 D-2 1560-UHI-760 D-350
NAS43DD5-36 D-2 1560-UHI1-761 D-359
NAS43DD10-14 D-2 1560-UH1-762-1 D-360
NAS43HT1I-7 D-2 1560-UH1-762-2 D-19
NAS43HT3-12 D-2 1560-UH1-764 D-361
NAS43HT3-82 D-2 1560-UH1-765 D-362
NAS43HT4-7 D-2 1560-UH1-772-1 D-353
NAS43HT4-28 D-2 1560-UH1-772-2 D-353
NAS521-16-12 D-2 1560-UHI-781 D-355
NYLC3 D-57 1560-UH1-791 D-356
RB8515-18-3 D-2 1560-UH1-981 D-402
SKRV2-1994 D415 1560-UH1-983-3 D-354
SP1152-2 D-640 1560-UH1-990-1 D-357
SP1699-1 D-641 1560-UH1-1023 D-368
SP1705-1 D-62 1560-UH1-1044 D-367
SP1706-1 D-63 1730-EG179 D407
SP1707-1 D64 178036-3 D-176
SP1707-2 D44 178038-3 D-176
SP1709-2 D65 178040-3 D-176
SP1710-1 D66 178042-3 D-176
SP1715-1 D-67 178044-3 D-176
SP3184-4 D-68 178050-3 D-176
SP3184-5 D68 178050-5 D-176
SP3184-6 D68 178050-7 D-176
SP401-1 D-54 178052-3 D-176
SP401-2 D-54 178052-5 D-176
SP469-1 D-58 178052-7 D-176
SP469-2 D-58 178065-1 D-220
SP516 D-59 1951-131-09 D-395
STP-41 D411 20-032-1 D-21
S8168-44A0170 D-2 20432-2 D-21
UH-1-IS0054-1 D-135 20432-3 D-21
UH-1-LU001-1 D42 20-036-8-24 D-69
UH-1-L0001-2 D42 204-001-222-1 D-11
W20396 D-20 204-001-790-1 D-81
Y1152-1-6 D-225 204401-849-1 D-81
Y1152-1-11 D-225

Change 8 D-3
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.

204-001-849-2 D-81 204-040-153-13 D-3


204-010-780-1 D-8 204-040-153-15 D-3
204-010-793-3 D-8 204-040-153-25 D-3
204-010-794-1 D-91 204-040-155-11 D-3
204-011-059-1 D-235 204-040-155-13 D-3
204-011-149-1 D-72 204-040-155-15 D-3
204-011-458-1 D-73 204-040-156-5 D-3
204-011-458-3 D-73 204-040-215-19 D-4
204-011-458-5 D-73 204-040-215-27 D-42
204-011-458-7 D-73 204-040-299-1 D-17
204-011-461-1 D-128 204-040-306-9 D-3
204-011-708-1 D-8 204-040-314-5 D-3
204-011-708-3 D-8 204-040-353-11 D-3
204-012-022-3 D-236 204-040-353-13 D-3
204-012-110-1 D-74 204-040-353-15 D-3
204-030-007-139 D-24 204-040-353-17 D-3
204-030-010-1 D-12 204-040-355-11 D-3
204-030-287-89 D-352 204-040-355-13 D-3
204-030-289-91 D-352 204-040-355-15 D-3
204-030-337-3 D-13 204-040-356-5 D-3
204-030-458-4 D-237 204-040-419-7 D-3
204-030-665-11 D-241 204-040-425-5 D-3
204-030-800-443 D-75 204-040-513-11 D-3
204-030-813-5 D-76 204-040-513-13 D-3
204-030-813-2 D-15 204-040-671-1 D-26
204-030-813-23 D-15 204-040-722-1 D-42
204-030-813-25 D-15 204-040-723-1 D-82
204-030-813-27 D-15 204-040-732-1 D-82
204-030-829-15 D-238 204-040-749-1 D-25
204-030-829-27 D-238 204-040-848-1 D-239
204-030-832-7 D-370 204-050-228-1 D-398
204-030-840-1 D-15 204-060-020-207 D-25
204-030-840-3 D-15 204-060-031-15 D-84
204-030-840-5 D-15 204-060-045-1 D-1
204-030-853-73 D-27 204-060-056-1 D-85
204-030-853-83 D-27 204-060-082-1 D-42
204-030-853-93 D-358 204-060-098-1 D-42
204-030-853-85 D-27 204-060-224-9 D-240
204-030-853-97 D-341 204-060-816-33 D-304
204-030-853-98 D-341 204-060-868-5 D-345
204-030-853-99 D-341 204-070-048-7 D-245
204-030-853-100 D-341 204-070-048-13 D-246
204-030-853-111 D-27 204-070-110-3 D-42
204-030-853-113 D-27 204-070-110-7 D-42
204-030-853-115 D-27 204-070-110-65 D-42
204-030-853-117 D-27 204-070-110-67 D-42
204-030-853-133 D-40 204-070-110-71 D-42
205-030-872-21 D-404 204-070-110-153 D-42
205-030-872-23 D-405 204-070-110-155 D-42
204-031-003-13 D-77 204-070-143-3 D-23
204-031-003-14 D-77 204-070-134-11 D-42
204-031-003-23 D-78 204-070-175-1 D-86
204-031-136-17 D-152 204-070-185-1 D-87
2104-031-139-3 D-79 204-070-230-1 D-88
204-031-251-1 D-80 204-070-255-1 D-89
204-031-347-25 D-352 204-070-255-2 D-89
204-031-766-1 D-403 204-070-255-13 D-90

D-4 Change 5
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.


204-070-255-14 D-90 204-070-848-3 D-250
204-070-274-1 D-92 204-070-855-7 D-33
204-070-275-1 D-93 204-070-904-1 D-34
204-070-343-1 D-26 204-071-523-1 D-2
204-070-476-1 D-31 204-071-539-3 D-98
204-070-528-1 D-94 204-071-542-3 D-2
204-070-583-1 D-95 204-071-577-1 D-99
204-070-585-1 D-96 204-072-054-1 D-100
204-070-749-1 D-97 204-072-083-1 D-101
204-070-794-1 D-26 204-072-258-1 D-251
204-070-798-1 D-26 204-072-258-3 D-252
204-070-806-3 D-247 204-072-259-1 D-253
204-070-812-1 D-248 204-072-265-1 D-42
204-070-812-3 D-26 204-072-267-1 D-42
204-070-818-1 D-26 204-072-268-1 D-42
204-070-818-3 D-26 204-072-355-1 D-42
204-070-845-1 D-249 204-072-364-1 D-42
204-075-143-5 D-36

D-4.1/(D-4.2 blank)
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.

204-075-143-7 D-36 205-030-137-4 D-262


204-075-152-3 D-260 205-030-148-3 D-263
204-075-160-1 D-102 205-030-163-25 D-307
204-075-163-1 D-38 205-030-163-125 D-308
204-075-173-35 D-28 205-030-163-129 D-309
204-075-177-13 D-305 205-030-164-215 D-264
204-075-181-9 D-2 205-030-163-231 D-310
204-075-207-3 D-32 205-030-163-329 D-311
204-075-230-3 D-258 205-030-213-4 D-312
204-075-230-5 D-259 205-030-239-3 D-265
204-075-243-1 D-39 205-030-239-5 D-266
204-075-264-1 D-254 205-030-245-13 D-15
204-075-264-3 D-255 205-030-245-15 D-15
204-075-264-5 D-256 205-030-245-43 D-15
204-075-264-9 D-257 205-030-245-45 D-15
204-075-520-1 D-103 205-030-245-61 D-157
204-076-032-3 D-104 205-030-245-67 D-157
205-001-104-1 D-105 205-030-247-25 D-129
205-030-007-77 D-106 205-030-257-15 D-267
205-030-007-97 D-107 205-030-302-5 D-130
205-030-007-98 D-107 205-030-302-6 D-130
205-030-007-99 D-108 205-030-309-13 D-131
205-030-007-107 D-109 205-030-385-17 D-313
205-030-007-109 D-110 205-030-385-18 D-313
205-030-007-111 D-111 205-030-385-21 D-314
205-030-007-113 D-112 205-030-407-121 D-315
205-030-007-131 D-113 205-030-407-317 D-316
205-030-007-132 D-113 205-030-431-1 D-132
205-030-007-133 D-114 205-030-432-1 D-132
205-030-007-134 D-114 205-030-484-15 D-15
205-030-007-155 D-115 205-030-484-17 D-15
205-030-007-157 D-116 205-030-539-7 D-317
205-030-007-159 D-117 205-030-539-11 D-15
205-030-007-179 D-118 205-030-543-15 D-135
205-030-007-180 D-119 205-030-543-17 D-136
205-030-007-231 D-118 205-030-611-15 D-318
205-030-007-233 D-120 205-030-614-13 D-137
205-030-007-245 D-121 205-030-615-93 D-319
205-030-007-246 D-121 205-030-615-94 D-319
205-030-007-271 D-122 205-030-671-7 D-138
205-030-007-272 D-122 205-030-671-9 D-138
205-030-007-337 D-123 205-030-711-27 D-321
205-030-007-341 D-124 205-030-711-28 D-321
205-030-007-347 D-306 205-030-729-49 D-322
205-030-007-351 D-125 205-030-737-3 D-139
205-030-009-51 D-365 205-030-737-5 D-140
205-030-028-5 D-126 295-030-814-17 D-141
205-030-028-6 D-126 205-030-819-21 D-323
205-030-028-25 D-126 205-030-828-1 D-142
205-030-028-27 D-126 205-030-828-5 D-143
205-030-029-5 D-133 205-030-846-33S D-324
205-030-029-25 D-261 205-030-849-7 D-144
205-030-031-7 D-127

Change 4 D-5
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.

205-030-850-21 D-325 205-040-203-1 D-4


205-030-872-21 D-404 205-060-020-7 D-162
205-030-872-23 D-405 205-060-110-1 D-275
205-030-919-33 D-412 205-060-204-1 D-163
205-030-919-37 D-223 205-060-205-19 D-276
205-030-919-38 D-223 205-060-205-20 D-276
205-030-137-1 D-145 205-060-254-9 D-399
205-030-250-3 D-198 205-060-424-1 D-42
205-031-250-13 D-146 205-060-440-1 D-42
205-031-423-31 D-268 205-060-509-3 D-165
205-031-423-32 D-268 205-060-536-1 D-166
205-031-423-33 D-268 295-060-540-19 D-167
205-031-423-34 D-268 205-060-580-1 D-42
205-031-481-15 D-269 205-060-581-1 D-42
205-031-481-23 D-270 205-060-582-1 D-42
205-031-481-29 D-270 205-060-583-1 D-42
205-031-481-33 D-406 205-060-584-1 D-42
205-031-668-43 D-147 205-060-585-1 D-42
205-031-668-51 D-15 205-060-586-1 D-42
205-031-668-53 D-148 205-060-587-1 D-42
205-031-668-65 D-271 205-060-589-1 D-42
205-031-669-101 D-369 205-060-590-1 D-42
205-031-669-105 D-352 205-060-591-1 D-42
205-031-669-137 D-320 205-060-592-1 D-42
205-031-669-151 D-49 205-060-593-1 D-42
205-031-669-152 D-49 205-060-594-1 D-42
205-031-801-53 D-149 205-060-648-1 D-42
205-031-837-19 D-150 205-060-649-1 D-42
205-031-837-20 D-150 205-060-690-1 D-42
205-031-837-21 D-150 205-060-691-1 D-42
205-031-862-17S D-272 205-060-692-1 D-42
205-031-862-19S D-273 205-060-693-1 D-42
205-031-862-21S D-272 205-060-694-1 D-42
205-031-862-47S D-274 205-060-695-1 D-42
205-031-898-1 D-151 205-060-696-1 D-42
205-040-125-11 D-3 205-060-697-1 D-42
205-040-125-15 D-3 205-060-770-1 D-168
205-040-130-1 D-132 205-060-802-11 D-169
205-040-131-1 D-153 205-060-802-13 D-169
205-040-142-1 D-42 205-060-805-13 D-352
205-040-143-1 D-42 205-060-805-35 D-397
205-040-144-1 D-42 205-060-805-37 D-397
205-040-145-1 D-42 205-060-805-41 D-400
205-040-146-1 D-42 205-060-810-15 D-170
205-040-147-1 D-42 205-060-810-16 D-170
205-040-148-1 D-42 205-060-816-33 D-346
205-040-150-1 D-42 205-060-826-79 D-326
205-040-151-1 D-42 205-060-826-81 D-171
205-040-152-1 D-154 205-060-826-83 D-172
205-040-154-3 D-155 205-060-826-85 D-172
205-040-156-3 D-156 205-060-838-1 D-173
205-040-159-1 D-42 205-060-860-3 D-174
205-040-164-1 D-26 205-060-860-4 D-174
205-040-169-1 D-158 205-060-862-1 D-175
205-040-170-1 D-159 205-060-868-5 D-345
205-040-202-1 D-160
205-040-202-3 D-161

D-6 Change 5
TM 55-1520-210-23-3
PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.
205-060-907-7 D-327
205-060-907-17 D-328
205-060-907-35 D-50
205-060-907-37 D-51
205-060-908-79 D-177
205-060-908-85 D-177
205-060-909-7 D-347
205-060-909-23 D-348
205-060-907-7 D-327
205-060-907-17 D-328
205-060-919-3 D-178
205-061-213-1 D-42
205-061-214-1 D-42
205-061-232-1 D-329
205-061-234-1 D-330
205-061-412-1 D-331
205-061-520-13 D-172
205-061-064-101 D-4

Change 4 D-6.1/(D–6.2 Blank)


TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.

205-061-521-1 D-332 205-070-366-1 D-42


205-061-600-1 D-42 205-070-404-1 D-186
205-061-601-1 D-42 205-070-404-3 D-187
205-061-604-1 D-42 205-070-416-5 D-188
205-061-606-1 D-42 205-070-416-7 D-188
205-061-607-1 D-42 205-070-416-13 D-188
205-061-608-1 D-42 205-070-430-1 D-189
205-061-609-1 D-42 205-070-430-3 D-189
205-061-610-1 D-42 205-070-436-1 D-42
205-061-611-1 D-42 205-070-439-1 D-42
205-061-612-1 D-42 205-070-440-1 D-42
205-061-614-1 D-42 205-070-441-1 D-42
205-061-615-1 D-42 205-070-448-1 D-42
205-061-616-1 D-42 205-070-450-3 D-190
205-061-617-1 D-42 205-070-452-1 D-191
205-061-618-1 D-42 205-070-452-3 D-191
205-061-619-1 D-42 205-070-475-1 D-42
205-061-624-1 D-42 205-070-476-1 D-42
205-061-643-1 D-179 205-070-483-1 D-192
205-061-643-3 D-333 205-070-484-1 D-42
205-061-645-1 D-42 205-070-485-1 D-42
205-061-647-1 D-42 205-070-486-1 D-42
205-061-649-1 D-42 205-070-487-1 D-42
205-061-650-1 D-42 205-070-488-1 D-42
205-061-651-1 D-42 205-070-490-1 D-42
205-061-652-1 D-42 205-070-491-1 D-42
205-061-653-1 D-42 205-070-493-1 D-193
205-061-654-1 D-42 205-070-493-3 D-193
205-061-655-1 D-42 205-070-494-1 D-194
205-061-659-1 D-42 205-070-609-1 D-195
205-061-661-1 D-42 205-070-656-1 D-196
205-061-662-1 D-42 205-070-769-1 D-197
205-061-663-1 D-42 205-070-772-1 D-279
205-061-664-1 D-42 205-070-795-1 D-280
205-061-665-1 D-180 205-070-801-1 D-26
205-061-666-1 D-181 205-070-810-1 D-26
205-061-668-1 D-42 205-070-829-1 D-26
205-061-669-1 D-42 205-070-840-1 D-26
205-061-670-1 D-42 205-070-850-1 D-26
205-061-671-1 D-42 205-070-853-1 D-26
205-061-672-1 D-182 205-070-853-3 D-26
205-061-674-1 D-42 205-070-859-1 D-26
205-061-675-1 D-42 205-070-862-1 D-281
205-061-677-1 D-183 205-070-882-1 D-282
205-061-684-1 D-184 205-070-942-1 D-199
205-062-614-1 D-42 205-072-038-1 D-335
205-062-662-1 D-42 205-072-039-1 D-283
205-062-663-1 D-42 205-072-208-1 D-412
205-062-680-1 D-42 205-072-221-3 D-278
205-062-681-1 D-42 205-072-222-1 D-99
205-062-696-1 D-277 205-071-118-101 D-366
205-070-054-1 D-334 205-071-118-103 D-366
205-070-226-1 D-26 .205-071-118-105 D-366
205-070-365-1 D-42 205-071-118-107 D-366
1 D-7
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.

205-072-224-1 D-284 305-076-202-1 D-42


205-072-225-1 D-285 305-076-203-1 D-42
205-072-226-1 D-286 305-076-204-1 D-42
205-072-227-1 D-287 305-076-205-1 D-42
205-072-227-3 D-288 305-076-206-1 D-42
205-072-264-1 D-164 305-076-207-1 D-42
205-072-269-3 D-200 205-076-208-1 D-42
205-072-274-3 D-201 205-076-209-1 D-42
205-072-278-1 D-42 205-076-210-1 D-42
205-072-304-1 D-42 205-076-212-1 D-42
205-072-305-1 D-42 205-076-213-1 D-42
205-072-317-1 D-289 205-076-214-1 D-42
205-072-403-1 D-202 205-076-215-1 D-42
205-072-410-1 D-42 205-076-216-1 D-42
205-072-424-1 D-42 205-076-217-1 D-42
205-075-126-1 D-203 205-076-221-1 D-42
205-075-126-9 D-204 205-076-223-1 D-42
205-075-126-13 D-205 205-076-227-1 D-42
205-075-133-1 D-206 205-076-230-1 D-216
205-075-134-1 D-42 205-076-231-1 D-42
205-075-134-1 D-207 205-076-232-1 D-42
205-075-135-15 D-208 205-076-233-1 D-42
205-05-135-19 D-292 205-076-234-1 D-217
205-075-137-3 D-336 205-076-235-1 D-42
205-075-142-3 D-209 205-076-236-1 D-42
205-075-142-5 D-293 205-076-237-1 D-42
205-075-142-9 D-294 205-076-238-1 D-42
205-075-142-11 D-185 205-076-240-1 D-42
205-075-144-3 D-210 205-076-241-1 D-42
205-075-151-1 D-295 205-076-242-1 D-42
205-075-210-3 D-296 205-076-244-1 D-42
205-075-210-5 D-297 205-076-245-1 D-42
205-075-229-1 D-211 205-076-246-1 D-42
205-075-237-5 D-298 205-076-247-1 D-42
205-076-025-11 D-218 205-076-248-1 D-42
205-076-025-15 D-218 205-076-249-1 D-42
205-076-033-1 D-42 205-076-250-1 D-42
205-076-101-1 D-212 205-076-251-1 D-42
205-076-101-3 D-213 205-076-252-1 D-42
205-076-102-1 D-214 205-076-253-1 D-42
205-076-118-1 D-215 205-076-254-1 D-42
205-076-131-1 D-42 205-076-255-1 D-42
205-076-136-1 D-42 205-076-257-1 D-42
205-076-138-1 D-42 205-076-258-1 D-42
205-076-140-1 D-42 205-076-259-1 D-42
205-076-141-1 D-42 205-706-025-11 D-218
205-076-156-1 D-42 205-706-025-15 D-218
205-076-157-1 D-42 205-706-025-17 D-337
205-076-158-1 D-42 205-706-025-19 D-338
205-076-159-1 D-42 205-706-029-11 D-290
205-076-160-1 D-42 205-706-029-15 D-291
205-076-161-1 D-42 205-961-102-17 D-299
205-076-200-1 D-42 205-961-102-25 D-300
205-076-201-1 D-42 205-961-102-33 D-301

D-8
TM 55-1520-210-23-3

PART NUMBER FIGURE NO. PART NUMBER FIGURE NO.


205-961-155-3 D-302 85T4-3-2 D-2
206-010-324-1 D-344 85T4-3-6 D-2
209-040-158-1 D-342 85T4-3-56 D-2
270-580292-12 D-349 85T4-4-4 D-2
28D00 D-43 85T4-4-8 D-2
397-1 D-340 85T4-4-24 D-2
49C16 D-44 85T4-4-34 D-2
50H1 D-45 85T4-4-38 D-2
5065695 D-376 85T4-4-50 D-2
5065696 D-393 85T4-5-2 D-2
5065698 D-392 85T4-5-15 D-2
528307 D-221 85T4-6-2 D-2
5310-UH1-036-1 D-364 85T4-6-4 D-2
5340-UH-1-6821 D-409 85T4-6-16 D-2
5340-UH-1-6823 D-409 85T4-7-2 D-2
59H21 D-47 85T4-7-4 D-2
67SPL12757-0114 D-339 85T4-8-1 D-2
70-017 D-53 85T4-8-2 D-2
70-001B8F18Z3 D-48 85T4-8-6 D-2
70-001B8F59Z3 D-48 85T4-9-3 D-2
70-001B10F66Z2 D-48 85T4-10-1 D-2
70-001B12F13Z3 D-48 85T4-10-2 D-2
70-001B12F22Z2 D-48 85T4-10-12 D-2
70-001B12F27Z2 D-48 85T4-11-3 D-2
70-001B12F52Z3 D-48 85T4-11-4 D-2
70-001B20F12Z3 D-48 85T4-12-1 D-2
70-004A10F23Z2 D-48 85T4-12-2 D-2
70-004A10F24Z2 D-48 85T4-14-1 D-2
70-004A10F25Z3 D-48 85T4-16-6 D-2
70-004A12F27Z2 D-48 85T4-375-2 D-2
70-00960006116 D-41.1 85T4-375-3 D-2
70-010J000A180 D-41 85T4-375-8 D-2
70-010J000G214 D-41 85T4-375-12 D-2
70-010K000H154 D-41 85T4-375-46 D-2
70-010K304Z134 D-41 85T4-375-52 D-2
70-010J000T164 D-41.2 85T4-500-2 D-2
70-010J000T174 D-41.2 85T4-500-4 D-2
70-010J000V38 D-41.2 85T4-500-6 D-2
745016 D-371 85T4-625-2 D-2
85T4-0-2 D-2 85T4-875-56 D-2
85T4-1-2 D-2 85T4-1000-8 D-2
85T4-1-27 D-2 85T4-1250-48 D-2
85T4-2-106 D-2 8531 804 D-364.1
85T4-2-2 D-2 8531 834 D-364.1
85T4-2-4 D-2 90-045-5 D-243
85T4-2-10 D-2 90-047-1 D-244
85T4-2-27 D-2 9524491 D-222
85T4-2-60 D-2 99C29 D-70
85T4-2-108 D-2 99C30 D-42
85T4-2-116 D-2
85T4-3-1 D-2

Change 9 D-9
TM 55-1520-210-23-3

Figure D-1. Part Number 204-060-045-1, FITTING, Reducer Engine Oil Inlet
Fabricate From NSN 4730-00-684-7446

D-10
TM 55-1520-210-23-3

FABRICATE FROM
PART NUMBER NOMENCLATURE NSN ID OD LG
NAS42DD4-16 SPACER, RIVET 5340-00-631-3905 0.127 0.260 0.250
NAS42DD6-8 SPACER, SLEEVE 5340-00-631-3904 0.190 0.385 0.125
NAS43-3-8 SPACER, SCREW AND BOLT 5340-00-826-6257 0.194 0.322 0.125
NAS43-3-24 SPACER, SCREW AND BOLT 5340-00-826-6257 0.194 0.322 0.375
NAS43-3-42 SPACER, SCREW AND BOLT 5340-00-826-6257 0.194 0.322 0.656
NAS43-3-48 SPACER, SCREW AND BOLT 5340-00-826-6257 0.194 0.322 0.750
NAS43-4-12 SPACER, SCREW AND BOLT 5340-00-632-1254 0.256 0.365 0.187
NAS43-4-14 SPACER, SCREW AND BOLT 5340-00-632-1254 0.256 0.365 0.218
NAS43-4-44 SPACER, SCREW AND BOLT 9535-00-167-2151 0.256 0.365 0.687
NAD43-4-108 SPACER, SCREW AND BOLT 5340-00-632-1254 0.256 0.365 1.687
NAS43-5-36 SPACER, SCREW AND BOLT 5340-00-632-1252 0.320 0.448 0.582
NAS43-5-48 SPACER, SCREW AND BOLT 5340-00-632-1252 0.320 0.448 0.750
NAS43-6-12 SPACER, SCREW AND BOLT 5340-00-540-3668 0.377 0.515 0.187
NAS43-6-30 SPACER, SCREW AND BOLT 5340-00-540-3668 0.377 0.515 0.468
NAS43DD1-16 SPACER, SLEEVE 5340-00-841-8565 0.143 0.260 0.250
NAS43DD1-7 SPACER, SLEEVE 5340-00-632-3562 0.143 0.260 0.114
NAS43DD3-9 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.140
NAS43DD3-10 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.186
NAS43DD3-12 SPACER. SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.187
NAS43DD3-19 SPACER, SLEEVE 5340-00-727-1891 0.194 0.322 0.206
NAS43DD3-21 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.328
NAS43DD3-22 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.343
NAS43DD3-23 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.359
NAS43DD3-28 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.437
NAS43DD3-30 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.468
NAS43DD3-31 SPACER, SCREW AND BOLT 5340-00-727-1891 0.194 0.322 0.484

Figure D-2. (Sheet 1 of 4)

D-11
TM 55-1520-210-23-3

FABRICATE FROM
PART NUMBER NOMENCLATURE NSN ID(I) OD (1) LG
NAS43DD3-36 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.562
NAS43DD3-38 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.593
NAS43DD3-44 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.687
NAS43DD3-45 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.703
NAS43DD3-48 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.750
NAD43DD3-50 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.781
NAS43DD3-53 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.828
NAS43DD3-54 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 0.843
NAS43DD3-64 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.000
NAS43DD3-65 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.015
NAS43DD3-67 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.046
NAS43DD3-70 SPACER, SCREW AND BOLT 5340-00-727-1981 *0.194 *0.322 1.093
NAS43DD3-74 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.156
NAS43DD3-76 SPACER, SCREW AND B0LT 5340-00-727-1891 *0.194 *0.322 1.187
NAS43DD3-80 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.250
NAS43DD3-88 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.375
NAS43DD3-92 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.437
NAS43DD3-96 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.500
NAS43DD3-98 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.531
NAS43DD3-112 SPACER, SCREW AND BOLT 5340-00-727-1891 *0.194 *0.322 1.750
NAS43DD4-10 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.156
NAS43DD4-16 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.250
NAS43DD4-23 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.359
NAS43DD4-28 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.437
NAS43DD4-38 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.594
NAS43DD4-60 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.937
NAS43DD4-61 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 0.953
NAS43DD4-71 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.385 1.109
NAS43DD5-36 SPACER, SCREW AND BOLT 5340-00-632-1255 *0.320 *0.448 0.567
NAS43DD10-14 SPACER, SCREW AND BOLT 5340-00-841-8565 *0.627 *0.765 0.218
NAS43HT1-7 SPACER, SCREW AND BOLT 5340-00-952-2955 *0.143 *0.260 0.109
NAS43HT3-12 SPACER, SCREW AND BOLT 5340-00-826-6257 *O.194 *0.322 0.187
NAS43HT3-82 SPACER, SCREW AND BOLT 5340-00-826-6257 *0.194 *0.322 1.281
NAS43HT4-7 SPACER, SCREW AND BOLT 5340-00-541-9565 *0.256 *0.385 0.109
NAS43HT4-28 SPACER, SCREW AND BOLT 5340-00-632-1254 *0.256 *0.365 0.437
NAS521-16-12 COUPLING, HOSE 4720-00-843-1731 2.000 2.126 3.000
85T4-O-2 TUBE, INSULATING 5970-00-623-8526 0.325 0.371 1.000
85T4-1-2 TUBE, INSULATING 5970-00-879-0525 0.294 0.334 1.000
85T4-1-27 TUBE, INSULATING 5970-00-870-0525 0.289 0.335 13.500
85T4-1-52 TUBE, INSULATING 5970-00-870-0525 0.294 0.334 26.00
85T4-1-106 TUBE, INSULATING 5970-00-870-0525 0.294 0.334 53.00
85T4-2-2 TUBE, INSULATING 5970-00-235-2725 0.258 0.304 1.000
85T4-2-4 TUBE, INSULATING 5970-00-235-2725 0.263 0.303 2.000

(1) Note: All dimensions nominal except as noted by*


Figure D-2. (Sheet 2 of 4)

D-12 Change 5
TM 55-1520-210-23-3

FABRICATE FROM
PART NUMBER NOMENCLATURE NSN ID OD LG
85T4-2-10 TUBE, INSULATING 5970-00-235-2725 0.263 0.303 5.000
85T4-2-27 TUBE, INSULATING 5970-00-235-2725 0.258 0.304 13.500
85T4-2-60 TUBE, INSULATING 5970-00-235-2725 0.258 0.304 30.00
85T4-2-108 TUBE, INSULATING 5970-00-235-2725 0.263 0.304 54.00
85T4-2-116 TUBE, INSULATING 5970-00-235-2725 0.263 0.304 58.00
85T4-3-1 TUBE, INSULATING 5970-00-263-1327 0.229 0.275 500
85T4-3-2 TUBE, INSULATING 5970-00-263-1327 0.229 0.275 1.000
85T4-3-6 TUBE, INSULATING 5970-00-263-1327 0.234 0.275 3.00
85T4-3-12 TUBE, INSULATING 5970-00-263-1327 0.229 0.275 6.00
85T4-3-56 TUBE, INSULATING 5970-00-263-1327 0.229 0.275 28.00
TUBE, INSULATING
85T4-4-4 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 2.00
85T4-4-24 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 12.00
85T4-34 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 17.00
85T4-48 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 24.00
85T4-50 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 25.00
85T4-5-2 TUBE, INSULATING 5970-00-263-1325 0.186 0.226 1.000
85T4-5-15 TUBE, INSULATING 5970-00-263-1325 0.186 0.226 7.500
85T4-6-2 TUBE, INSULATING 5970-00-235-2719 0.166 0.206 1.000
85T4-6-4 TUBE, INSULATING 5970-00-235-2719 0.162 0.208 2.000
85T4-6-16 TUBE, INSULATING 5970-00-235-2719 0.166 0.206 8.000
85T4-7-2 TUBE, INSULATING 5970-00-557-6245 0.148 0.188 1.000
85T4-7-4 TUBE, INSULATING 5970-00-557-6245 0.144 0.186 2.000
85T4-8-1 TUBE, INSULATING 5970-00-284-8468 0.133 0.173 0.500
85T4-8-2 TUBE, INSULATING 5970-00-284-8468 0.133 0.173 1.000
85T4-8-6 TUBE, INSULATING 5970-00-284-8468 0.133 0.173 3.000
85T4-9-3 TUBE, INSULATING 5970-00-843-2281 0.114 0.160 1.500
85T4-10-1 TUBE, INSULATING 5970-00-826-9827 0.106 0.138 0.500
85T4-1O-14 TUBE, INSULATING 5970-00-826-9827 0.106 0.140 7.000
85T4-4-8 TUBE, INSULATING 5970-00-284-9698 0.208 0.248 4.00
85T4-10-2 TUBE, INSULATING 5970-00-826-9827 0.102 0.138 1.000
85T4-10-12 TUBE, INSULATING 5970-00-826-9827 0.106 0.140 6.000
85T4-11-3 TUBE, INSULATING 5970-00-284-8627 0.095 0.138 1.500
85T4-11-4 TUBE, INSULATING 5970-00-284-8627 0.095 0.138 2.000
85T4-12-1 TUBE, INSULATING 5970-00-557-6244 0.085 0.119 500
85T4-12-2 TUBE, INSULATING 5970-00-557-6244 0.085 0.138 1.000
85T4-14-1 TUBE, INSULATING 5970-00-235-2721 0.066 0.088 0.500
85T4-16-6 TUBE, INSULATING 5970-00-809-9163 0.053 0.085 3.000
85T4-375-2 TUBE, INSULATING 5970-00-235-2728 0.375 0.431 1.000
85T4-375-3 TUBE, INSULATING 5970-00-235-2728 0.375 0.431 1.500
85T4-375-8 TUBE, INSULATING 5970-00-235-2728 0.375 0.431 4.000
85T4-375-12 TUBE, INSULATING 5970-00-235-2728 0.375 0.431 6.000
85T4-375-46 TUBE, INSULATING 5970-00-235-2728 0.375 0.431 23.000
85T4-375-52 TUBE, INSULATING 5970-00-235-2728 0.375 0.419 26.00
85T4-500-2 TUBE, INSULATING 5970-00-557-6254 0.500 0.248 1.000
Figure D-2. (Sheet3 OF 4)

Change 5 D-13
TM 55-1520-210-23-3

FABRICATE FROM
PART NUMBER NOMENCLATURE NSN ID OD LG
85T4-500-4 TUBE INSULATING 5970-00-557-6254 0.500 0.556 2.000
85T4-500-6 TUBE, INSULATING 5970-00-557-6254 0.500 0.556 3.000
85T4-625-2 TUBE, INSULATING 5970-00-615-9853 0.625 0.695 1.000
85T4-875-56 TUBE, INSULATING 5970-00-828-1090 0.875 0.955 28.00
85T4-1000-8 TUBE,INSULATING 5970-00-882-5007 1.000 1.060 4.000
85T4-1250-48 TUBE,INSULATING 5970-00-284-8480 1.250 1.340 24.00
204-071-523-1 TUBE,GUARD 4710-00-277-3627 0.652 0.750 9.000
204-071-542-3 TUBE,GUARD 4710-00-279-0917 0.180 0.250 8.500
204-075-181-9 SPACER 9330-00-260-3806 0.250 1.000 0.250

Figure D-2. (Sheet 4 of 4)

D-14 Change 5
TM 55-1520-210-23-3

FABRICATE FABRICATE
PART NUMBER NOTES PART NUMBER NOTES
FROM NSN FROM NSN
204-040-153-13 1560-00-898-1615 A,B 204-040-353-17 1560-00-894-6539 A,B
204-040-153-15 1560-00-894-6539 A,B 204-040-355-11 1560-00-491-0880 A,B
204-040-153-25 1560-00-898-1614 A,B 204-040-355-13 1560-00-491-0880 A,B
204-040-155-11 1560-00-491-0880 A,B 204-040-355-15 1560-00-893-4551 A,B
204-040-155-13 1560-00-491-0880 A,B 204-040-356-5 1560-00-893-4598 A,B
204-040-155-15 1560-00-893-4551 A,B 204-040-419-7 1560-00-898-1576 A,B
204-040-156-5 1560-00-898-1615 A,B 204-040-425-5 1560-00-898-1576 A,B
204-040-306-9 1560-00-893-4551 A,B 204-040-513-11 1560-00-491-0880 A,B
204-040-314-5 1560-00-894-6539 A,B 204-040-513-13 1560-00-491-0880 A,B
204-040-353-11 1560-00-893-4552 A,B 205-040-125-11 I 1560-00-894-6539 A,B
204-040-353-13 1560-00-893-4598 A,B 205-040-125-15 1560-00-894-6539 A,B
204-040-353-15 1560-00-894-6539 A,B

NOTES
A. COUNTERSINK 100° BEFORE PLATING
B. SIDES OF PLATES TO BE PARALLEL WITHIN
0.0002 T.I.R. AFTER PLATING

Figure D-3 Shims

D-15
TM 55-1520-210-23-3
NSN 9535-00-232-0378
D-16
TM 55-1520-210-23-3
AN8031-8-183
D-17
TM 55-1520-210-23-3

NOTES:
1. MATL. PER SPEC. QQA318
2. FINISH IRIDITE PER SPEC.
MIL-C-5541

Figure D-6. Part Number A6544, CLIP, Wire Light


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-250/5,0.063 Inch Thick

D-18
TM 55-1520-210-23-3

Figure D-7. Part Number A6545, BRACKET, LH


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5 0.063 Inch Thick

D-19
TM 55-1520-210-23-3

BREAK SHARP) EDGES .025 x 45° or .025 R


DIAMETERS TO BE CONCENTRIC
TO .010 T.I.R.

PART NUMBER NAME FABRICATE FROM ID OD THK


204-010-780-1 WASHER 5310-00-167-0766 0.397 0.390 1.125 ± .01 0.063 ± .01
204-010-793-3 WASHER 5310-00-167-0766 0.256 0.263 0.700 ± .01 0.063 ± .01
204-011-708-1 WASHER 5310-00-167-0766 0.457 1.125 ± .01 0.063 ± .01
204-011-708-3 WASHER 5310-00-167-0768 0.452 1.625 ± .01 0.063 ± .01

WASHER, FLAT

Figure D-8.

D-20
TM 55-1520-210-23-3

Figure D-9 Part Number A6546, BRACKET


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-21
TM 55-1520-210-23-3

Figure D-10. Part Number A6910, WIRE ASSEMBLY, Lamp


Fabricate from: NSN 5940-00-557-1627
NSN 6145-00-998-7609

D-22
TM 55-1520-210-23-3

Figure D-11. Part Number 204-001-222-1 NUT, Collective Stick Lock


Fabricate from: NSN 5310-00-566-8864 (MS 172243)
Material: Steel AMS 6381 or AMS 6382

D-23
TM 55-1520-210-23-3

Figure D-12. Part Number 204-030-010-1 STOP, Windshield Wiper


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY, Sheet, Federal Specification QQ-A-250/5,
0.063 Inch Thick

D-24
TM 55-1520-210-23-3

Figure D-13. Part Number 204-030-337-3 DOOR, Cyclic


Fabricate from: NSN 9535-00-086-9729
Material: 7075 AL ALY, T6, Federal Specification QQ-A-250/13,
0.025 Inch Thick

D-25
TM 55-1520-210-23-3
NSN 935-00-232-0378
D-26
TM 55-1520-210-23-3
D-27
TM 55-1520-210-23-3
D-28

AN257-2-650

204-030-831-21
204-030-813-23
204-030-813-25
204-030-813-27
204-030-840-1
204-030-840-3
204-030-840-5
205-030-245-13
205-030-245-53
205-030-245-43
205-030-245-45
205-030-484-15
205-030-484-17
205-030-539-11

205-031-668-51
TM 55-1520-210-23-3

NOTES:
1. MATL: 5052-H32 AL PER SPEC QQ-A-318
2. FINISH: IRIDITE PER SPEC. MIL-C-5541
3. THREADS PER SPEC MIL-S-7742

Figure D-16. Part Number A9116-2 PLATE


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheetr Federal Specification, QQ-A-250/5, 0.063 Inch Thick

D-29
TM 55-1520-210-23-3

Figure D-17. Part Number 204-040-299-1 BRACKET, Oil Drain Line


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-30
TM 55-1520-210-23-3

NOTE:
1. COAT WITH PRESERVATIVE OIL AND WRAP IN
MOISTURE-PROOF PAPER (OR EQ.)

Figure D-18. Part Number CSC536-3, PIN, Cam


Fabricate from: NSN 9510-00-234-7620

D-31
TM 55-1520-210-23-3

FABRICATE
PART NUMBER FROM NSN A B C D E LG

NAS 1455-00-3C 4010-00-262-1551 0.440 0.274 0.100 0.220 0.120 3 IN.


NAS 1455-00-5 4010-00-228-9948 0.440 0.274 0.100 0.220 0.120 5 IN.
NAS 1455-1A2-5 4010-00-554-8661 0.576 0.350 0.109 0.178 0.295 5 IN.
NAS 1455-B00-5 4010-00-554-8661 0.440 0.274 0.100 0.220 0.120 5 IN.
NAS 1455-A-00-4 4010-00-262-1551 0.440 0.274 0.100 0.220 0.120 4 IN.
1560-UH1-762-2 4010-00-554-8661 0.440 0.274 0.100 0.220 0.120 6 IN.
1560-UH1-762-2 * 5315-00-194-2455 0.440 0.274 0.100 0.220 0.120 6 IN.

CHAIN, WELDLESS

* Use with P/N 1560-UH1-762-2 only

Figure D-19.

D-32
TM 55-1520-210-23-3

Figure D-20. Part Number W20396, BRACKET


Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5, 0.050 Inch Thick

D-33
TM 55-1520-210-23-3

Figure D-21. Part Numbers 20-032-1 BRACKET SUPPORT


20-032-2
20-032-3
Fabricate from: NSN 9535-00-232-0378
Material 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5, 0.063 Inch Thick

D-34
TM 55-1520-210-23-3

Figure D-22. Part Number: MS20253P2-538 PIN, HINGE


Fabricate from: NSN 5340-00-043-3723
Material: Rod, Straight, Headless Cres. Cadmium Plated. 0.089 Inch Diameter

Figure D-23. Part Number 204-070-143-3 PLATE, Correction Card Holder


Fabricate from: NSN 9535-00-167-2277
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5, 0.020 Inch Thick

D-36
TM 55-1520-210-23-3

Figure D-24. Part Number 204-030-007-139 DOOR ASSEMBLY


Fabricate from: NSN 9535-00-167-2279
NSN 5340-00-209-7519
NSN 5325-00-838-8804
NSN 5325-00-141-4002
Material: 2024 AL ALY, Federal Specification, QQ-A-25, 0.020 Inch Thick

D-36
TM 55-1520-210-23-3
Figure D-25.
204-060-020-207
204-040-749-1
D-37
TM 55-1520-210-23-3
Figure D-26. (Sheet 1 of 3)
D-38
TM 55-1520-210-23-3

Figure D-26. (Sheet 2 of 3)


D-39
TM 55-1520-210-23-3

204-040-671-1

204-070-343-1
204-070-794-1
204-070-798-1
204-070-812-3
204-070-818-1
204-070-818-3
205-040-164-1
205-070-226-1
205-070-801-1
205-070-810-1
205-070-829-1
205-070-840-1
205-070-850-1

205-070-853-1
205-070-853-3
205-070-859-1

Figure D-26. (Sheet 3 of 3)

D-40
TM 55-1520-210-23-3

204-030-853-73

204-030-853-83

204-030-853-85

204-030-853-111

204-030-853-113

204-030-853-115

204-030-853-117

Figure D-27 D-41


TM 55-1520-210-23-3

204-075-173-35

D-42
TM 55-1520-210-23-3
Figure D-29.

BL6750
D-43
TM 55-1520-210-23-3

NOTES:
1. REMOVE ALL BURRS & SHARP EDGES
2. SURFACE ROUGHNESS AS ROLLED OR DRAWN
PUNCHED, CUT OR MACHINED SURFACES TO
HAVE 125
3. FINISH: ANODIZED PER MIL-A-8625
TYPE II, DYE BLACK

Figure D-30. Part Number BL8359 COVER, TENSION ROLL


Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick
TM 55-1520-210-23-3
204-070-476-1
D-45
TM 55-1520-210-23-3

Figure D-32. Part Number: 204-075-207-3 SWITCH GUARD


Fabricate from: NSN 5830-00-681-4897
Material: Switch Guard - Make From P/N 8497K2, Switch Guard, Cutler Hammer
Milwaukee, Wise. Code Ident No. 15605

Figure D-33. part Number 204-070-855-7 PLATE - Cable Guide


Fabricate from: NSN 9535-00-232-0405
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.090 Inch Thick

D-46
TM 55-1520-210-23-3

Figure D-34. Part Number 204-070-904-1 SPACER, Block-head Guard


Fabricate from: NSN 9330-00-260-3806
Material: Plastic Sheet Phenolic, Federal Specification MIL-P-15035 TYPE FBG 0.1875 Inch Thick

D-47
TM 55-1520-210-23-3

NOTES:
1. REMOVE ALL BURRS & SHARP EDGES
2. GRIND OR CUT HEAD OF BOLT TO DIM SHOWN

Figure D-35. Part Number BL8458 BOLT, MACHINE


Fabricate from: NSN 5306-00-180-2777
Material: Bolt, Machine, Cres. Passivated Finish, Make from AN4CN3A Bolt

Figure D-36. Part Number 204-075-143-5 & 7 BRACKET, Plug Mounting


Fabricate from: NSN 9535-00-232-0378
Material: 2024 ALALY Sheet, Federal Specification, QQ-A-250/5, 0.063 inch Thick

D-48
TM 55-1520-210-23-3

PART NUMBER FABRICATE FROM NSN NOTES:


MS27212-1-3 5940-00-950-1610 1. LAST DASH NUMBER INDICATES
MS27212-1-9 5940-00-950-1610 NUMBER OF STUDS.
MS27212-1-10 5940-00-950-1610 2. ALLOWANCE MUST BE MADE
MS27212-1-12 5940-00-950-1610 FOR THE LOSS OF ONE STUD
MS27212-1-14 5940-00-950-1610 FOR EACH CUT.
MS27212-1-15 5940-00-950-1610

TERMINAL BLOCK

Figure D-37.

D-49
TM 55-1520-210-23-3

Figure D-38. Part Number 204-075-163-1 PANEL, A.C. Circuit Breakers Pedestal
Fabricate from: NSN 9535-00-554-1412
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362, 0.050 Inch Thick

D-50
TM 55-1520-210-23-3

Figure D-39. Part Number 204-075-243-1 PLATE RECEPTACLE, Control Panel


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5,
0.032 Inch Thick

D-51
TM 55-1520-210-23-3
204-030-853-1333
D-52
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS8000 Series (Sheet 1 of 9)

Change 8 D-53
TM 55-1520-210-23-3

CONFIGURATION AND MATERIAL


COMBINATION ALUMINUM AND (MIL-H-27267) HOSE CUT OFF FACTOR
CORROSION RESISTANT STEEL (275°) FITTING ENDS
(MIL-F-27272) (HCOF) INCHES VS HOSE DASH SIZE NO.

1 2 1 2 -¾C -4C -5C -6C -8C -10C -12C -16C -20C -24C

MS27053 MS27053 1.86 2.10 2.26 2.60 2.88 3.32

MS27053 MS27059 2.72

MS27053 MS27055 2.63 3.18 3.44 3.86 4.41

MS27053 MS27060 2.24

2.46 3.05 3.35 3.78 4.34


MS27053 MS27057

MS27059 MS27059 3.58

3.16 4.10 4.28 4.84 5.50

3.10

2.99 3.97 4.19 4.76 5.43

MS27060 MS27060 2.62

MS27057 MS27057 2.82 3.84 4.10 4.68 5.34

EXAMPLE OF HOSE CUTOFF FACTOR


FOR A -8, ½ TUBE OD. 18½ ASSEMBLY LENGTH, STYLE K THE BULK HOSE
LENGTH - 18.50 MINUS THE HCOF, -18.50-3.58-14.92
BULK HOSE LENGTH NEEDED IS 14.92 INCHES.
FITTINGS TO MATE WITH PARTS DESIGNED TO MS33656

Figure D-41. Hose Assembly MS8000 Series (Sheet 2 of 9)

D-54
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS8000 Series (Sheet 3 of 9)

D-55
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS8001 Series (Sheet 4 of 9)

D-56
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS8001 Series (Sheet 5 of 9)

D-57
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS8001 Series (Sheet 6 of 9)

D-58
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS87028 thru MS87032 Series (Sheet 7 of 9)

D-59
TM 55-1520-210-23-3

Figure D-41. Hose Assembly MS87028 thru MS87032 Series (Sheet 8 of 9)

D-60
TM 55-1520-210-23-3

MS2871-3
MS28741-4
MS28741-3
MS28741-6
MS28741-8
MS28741-10
MS28741-12
MS28741-16
MS28741-20
MS28741-24
MS28741-32
NOTES:

(a) HOSE ASSEMBLIES TO BE SPECIFIED IN THE FOLLOWING LENGTH INCREMENTS ONLY


12 INCHES LONG AND UNDER - NOT LESS THAN 1/8
12 TO 18 INCHES LONG - NOT LESS THAN 1/4
OVER 18 INCHES LONG - NOT LESS THAN 1/2

(b) ASSEMBLY NUMBER MS28741-3 INACTIVE FOR DESIGN FOR HYDRAULIC USE.
MS224587 END FITTINGS ARE DIMENSIONALLY AND FUNCTIONALLY INTERCHANGEABLE
WITH MS28740. END FITTINGS SHALL CONFORM TO MIL-A-5070
ASSEMBLIES SHALL BE PROOF PRESSURE TESTED IN ACCORDANCE WITH SPECIFICATION MIL-M-8795.

SEE MIL-M-8796 FOR USE, OPERATING PRESSURE AND AGE CONTROL OF HOSE ASSEMBLY
MS ASSEMBLY NUMBERS FOR USE OF AIRCRAFT CONTRACTORS AND HOSE ASSEMBLIES ONLY
PROVISIONING PARTS BREAKDOWN MUST LIST COMPONENT PARTS SPARE AND MAINTENANCE PARTS
ARE NOT TO BE ORDERED BY SERVICES UNDER THE ASSEMBLY NUMBER SERVICES TO ORDER END
FITTINGS BY THEIR INDIVIDUAL PART NUMBER AND HOSE CONFORMING TO MIL-M-8794.

© EACH HOSE ASSEMBLY SHALL BE IDENTIFIED WITH A DURABLE PERMANENTLY ATTACHED TAG PLAINLY
MARKED WITH THE MILITARY STANDARD (MS) HOSE ASSEMBLY NUMBER, DATE OF ASSEMBLY, CURE DATE
OF THE HOSE, AND THE MANUFACTURER’S NAME AND PART NUMBER. THE NAME, TRADEMARK OR SYMBOL
OF THE HOSE ASSEMBLER SHALL BE IMPRESSION STAMPED OR VIBRATOR ETCHED ON A BLANK SURFACE
OF BOTH END ADAPTERS.
EXAMPLE OF PART NUMBER: MS28741-8-0184 - HOSE ASSEMBLY FOR 1/2 OD TUBING - LENGTH - 18-1/2 INCHES
FRACTIONS IN EIGHTS OF AN INCH
INCHES
SIZE
LENGTH L SHALL ALWAYS BE SPECIFIED BY FOUR DIGITS, THE LAST DIGIT SHALL ALWAYS INDICATE FRACTIONS
BY ElGHTS OF AN INCH
DIMENSIONS IN INCHES UNLESS OTHERWISE SPECIFIED, TOLERANCE LENGTH L 1/8 (L UNDER 18)
1/4 (L FROM 18 TO 36)
1/2 (L OVER 36 TO 50)
1 PERCENT (L OVER 50)

Figure D-41. Hose Assembly MS28741 Series (Sheet 9 of 9)

D-61
TM 55-1520-210-23-3

P/N 70-009 HOSE ASSEMBLIES SHALL BE FABRICATED SO THAT THE FIRE SLEEVE
WILL COVER THE SOCKET FOR THE FITTING. ON AL ALY SOCKETS, THE FIRE
SLEEVE COVERING THE FULL LENGTH OF THE SOCKET SHALL BE PROTECTED
WITH SILICONE RUBBER AND SHALL BE BONDED, USING END DIP COMPOUND, TO
THE SOCKET AT THE END TO PREVENT MOISTURE ENTRAPMENT.

Figure D-41.1. Hose Assembly, Fire Resistant (70-009 Series)

D-62
TM 55-1520-210-23-3

STYLES AND MATERIALS OF END


FITTINGS (FLARED)
Combina-
tions
Code Material Fitting Style Material Fitting Style
A Alum. I Alum. I
B Alum. II Alum. II
C Alum. III Alum. III
D Steel I Steel I
E Steel II Steel II
F Steel III Steel III
G Alum. I Alum. III
H Alum. I Alum. II
T Alum. I Alum. II
V Alum. I Alum. III
W Alum. II Alum. III
X Steel I Steel II
Y Steel I Steel III
Z Alum. II Alum. III

PROVISIONS MADE TO CALLOUT HOSE WITH CHAFE GUARD


Figure D-41.2. Hose Assembly, Non-Fire Resistant (Sheet 1 of 2)

Change 9 D-62.1
TM 55-1520-210-23-3

EXAMPLE OF CALLOUT:

70-010J240C484 = HOSE ASSEMBLY-NON FIRE RESISTANT, .5 INCH O.D., 240°


ROTATION, 90° ALUMINUM FITTINGS BOTH ENDS, 48.5 INCHES LONG,
WITHOUT CHAFE GUARD.

70-010W000C480 = HOSE ASSEMBLY-NON FIRE RESISTANT, .5 INCH O.D., 0°


ROTATION, 90° ALUMINUM FlTTINGS BOTH ENDS, 48.0 INCHES LONG, WITH
CHAFE GUARD.

NOTES: I. SIMILAR TO MS87028 THRU MS87032 EXCEPT HOSE


ASSEMBLY SHALL CONFORM TO BELL PROCUREMENT
SPECIFICATION 299-947-045, CLASS “A”.

2. ON HOSE SIZES 3, 4, AND 5; ALUMINUM FORGED BODY


IS INACTIVE FOR FUTURE INSTALLATION AND DESIGN.

3. FOR NEW DESIGN, FRACTIONAL LENGTH HOSES SHALL


BE SPECIFIED IN THE FOLLOWING INCREMENTS ONLY:
(a) UNDER 18 INCHES LONG = 1/4 INCH INCREMENTS
ONLY. (2, 4, OR 6 ONLY)

(b) OVER 18 INCHES LONG = 1/2 INCH ONLY (4 ONLY)

4. HOSE ASSEMBLY SHALL BE CERTIFIED TO THE FOLLOWING BY TSO


TAG ATTACHED:

FAA TSO-C53a TYPE A

5. IDENTIFY WITH BELL STANDARD PART NUMBER.

MAXIMUM LENGTH OF HOSE ASSEMBLY IS 99.5 INCHES LONG

CHAFE GUARD TO BE TRANSLUCENT VINYL PLASTIC PER MIL-I-7444


TYPE I, AND SHALL COME WITHIN .19 OF FlTTING EACH END.

Figure D-41.2. Hose Assenbly, Non-Fire Resistant (Sheet 2 of 2)

D-62.2 Change 5
TM 55-1520-210-23-3

D-1. TUBE BENDING DATA. The information contained in this section discloses, as applicable,
quantities of material and fittings, bend radii, angles, dimension, and all other data required for
fabrication of tube assemblies.

a. Table D-3 gives the material, NSN’s, and quantities of the stock required to fabricate each tube
assembly. The stock dimension column will indicate a length of 2 to 3 inches longer than is
actually required for the finished tube. The last column includes the applicable system for each
tube assembly, such as Fuel, Lubrication, etc.

b. Figure D-42 illustrates the type of dial marking, end references (“X” and “Y”), and dimensional
references (“A” and “B”), to coincide with the data on Table D-4,The Type of Ends (I thru VI) are
defined, and the “Notes” are provided for additional information.

c. Table D-4 includes all the dimensions (inches), angles (degrees), and other information required
to fabricate the tube assemblies. The use of Table D-4 is described in the following example. The
columns are numbered for reference only.

EXAMPLE

205-061-619-1

Column 1. PART NUMBER – Tube Part Number in alpha numerical order.

Column 2. BEND NO. – Bend Number 1, 2, etc., numbering from “Y” end of tube. The last block in
Column 2 will be blank.

Column 3. DIMENSION “A” FROM “Y” END – Refer to Figure D-42. Dimension “A” is the
distance from “Y” End before bending, to the beginning point of each bend to be
performed. (See Example.) “A” dimension for No. 1 bend is 1-1/16 inch. “A” dimension
for No. 2 bend is 91/8 inch,

DIMENSION “B” – Dimension “B” is the exact tube length before tube is bent, including
allowances for flaring or beading ends. (See Example. ) “B” Dimension is 1 1 3/8 inches.

Column 4. BEND RADIUS – Specifies the radius of each bend. (See Example.) Bend Radius for Nos. 1
and 2 bends is 9/16 inch.

TYPE END “Y” – Refers to type of end(I thru VI). See Figure D-42, “Type of Ends”, for
definition. (See Example.) Type of End “Y” is III, indicating a Double Flare.

D-62.3/(D-62.4 blank)
TM 55-1520-210-23-3

TYPE OF ENDS
NOTES: I SINGLE FLARE - MS33584
7. BEND RADI SHALL CONFORM II BEAD - MS33660 TYPE “ A”
1. SELECT MATERIAL AND END UNLESS NOTED.
FITTINGS FROM TABLE D-3. TO MS33611.
III DOUBLE FLARE - MS33583
8. NUTS AND SLEEVES INSTALLED IV PLAIN SQUARE
2. REFER TO TUBE BENDING V ANGLE - 45° SCARF UNLESS
DATA, TABLE D-4, FOR ALL PER MS33566.
NOTED.
DIMENSIONS, ANGLES, AND VI OTHER - AS DESIGNATED
DIAL SETTINGS. 9. PRESSURE TEST TO PSI CALLED
OUT IN TUBE BENDING DATA,
3. MARK DIMENSION “A” FOR TABLE D-4, IF APPLICABLE.
EACH BEND, AND DIMENSION
“B” PRIOR TO BENDING. 10. IDENTIFY TUBE ASSEMBLY BY
MARKING PART NUMBER WITH
4. MAKE FIRST BEND WITH DIAL RUBBER INK STAMP OR FELT
SET AT 0 DEG AND ROTATE PEN.
DIAL TO “RIGHT” (CLOCKWISE)
AND MAKE REMAINING BENDS
AT SPECIFIED DIAL SETTINGS.

5. CUT “X” END AFTER BENDING.


IF SCARF IS REQUIRED SET
DIAL AND CUT TO SPECIFIED
ANGLE.

6. TRIM AND BURR ENDS “X” AND


“Y” AS NECESSARY.

Figure D-42.

D-63
TM 55-1520-210-23-3

Column 5. DIAL SETTING — The dial setting is the degree of tube rotation from plane of first bend.
The dial setting (degree of tube rotation) will depend on the type of dial marking used. The
dial settings referenced in Table D-4 correspond to the type of dial marking illustrated
in Figure D-42.

TYPE OF END ‘X” — Refers to type End (I thru VI). See Figure D-42 “Type of Ends”, for
definition. (See Example.) Type of End “X” is V, indicating “Angle 45 degrees scarf.”

Column 6. BEND ANGLE — Specifies the degree of bend through which the tube is bent, as shown
in Figure D-42. (See Example.) The bend angle (degree of bend) for 1st bend is 45 degrees,
2nd bend is 68 degrees.

NOTE

This is the actual number of degrees required in the bend. When


pressure is released from the tube bender, a small amount of
“spring back” varying in proportion to hardness and elongation
characteristics of the tubing will necessitate a certain amount of
over-run to accomplish the exact bend angle.

PRESSURE TEST — The pressure test, if applicable, is indicated in psi (pounds per square
inch). (See Example. ) Pressure test is indicated as N/A, meaning “Not Applicable”.

Column 7. END FITTINGS AND NOTES — The Part Number of End Fitting, if required, and their
identity to the correct End (“X” and “Y”) are referenced. Additional notes will be included
in this column, as required. (See Example.) The End Fittings for “Y” End are AN818-4D
and MS20819-4D. For “X” End, no fittings are required. A scarf is cut on End “X”, with
dial setting at 320 degrees.

D-64
TM 55-1520-210-23-3

ITEM
NUMBER PART NUMBER NSN NOMENCLATURE

1. MIL-H-27267-10 4720-00-857-1730 Hose


2. MIL-H-27267-12 4720-00-857-1734 Hose
3. MIL-H-27267-16Z 4720-00-857-1729 Hose
4. MIL-H-27267-4 4720-00-857-1732 Hose
5. MIL-H-27267-5 4720-00-857-1736 Hose
6. MIL-H-27267-6 4720-00-857-1731 Hose
7. MIL-H-27267-8 4720-00-815-6354 Hose
8. MIL-H-8794-4 4720-00-639-9907 Hose
9. 601-10 4720-00-541-8328 Hose
10. M83797/1-KR 4720-00-555-3499 Hose
11. MS87027-16R 4720-00-540-6434 Hose
12. MS87027-4 4720-00-541-9281 Hose
13. MS87027-6 4720-00-611-2548 Hose
14. MS87027-8 4720-00-580-6618 Hose
15. MS24587-4 4730-00-842-2200 Fitting Assembly
16. MS27053-10 4730-00-125-2640 Fitting Assembly
17. MS27053-10C 4730-00-889-2477 Fitting Assembly
18. MS27053-12 4730-00-935-9382 Fitting Assembly
19. MS27053-12C 4730-00-889-2478 Fitting Assembly
20. MS27053-16 4730-00-889-2473 Fitting Assembly
21. MS27053-4C 4730-00-889-2474 Fitting Assembly
22. MS27053-6C 4730-00-982-9736 Fitting Assembly
23. MS27053-8C 4730-00-889-2476 Fitting Assembly
24. MS27055-10C 4730-00-884-1232 Fitting Assembly
25. MS27055-12 4730-00-935-9383 Fitting Assembly
26. MS27055-12C 4730-00-884-1234 Fitting Assembly
27. MS27055-16 4730-00-884-1231 Fitting Assembly
28. MS27057-10C 4730-00-132-3162 Fitting Assembly
29. MS27057-12 4730-00-130-4269 Fitting Assembly
30. MS27057-12C 4730-00-132-3163 Fitting Assembly
31. MS27057-16 4730-00-135-8851 Fitting Assembly
32. MS27059-4C 4730-00-889-2465 Fitting Assembly
33. MS27059-6C 4730-00-889-2468 Fitting Assembly
34. MS27060-4C 4730-00-013-6970 Fitting Assembly
35. MS27060-6C 4730-00-013-6969 Fitting Assembly
36. MS27060-8C 4730-00-228-1106 Fitting Assembly
37. MS27381-12 4730-00-054-7661 Fitting Assembly
38. MS27381-4C 4730-00-054-7650 Fitting Assembly
39. MS27381-5C 4730-00-877-9876 Fitting Assembly
40. MS273831-6C 4730-00-053-0379 Fitting Assembly
41. MS27381-8 4730-00-053-0389 Fitting Assembly
42. MS27381-8C 4730-00-929-5705 Fitting Assembly
43. MS27382-12 4730-00-053-0411 Fitting Assembly
44. MS27384-4C 4730-00-057-0665 Fitting Assembly
45. MS27384-5C 4730-00-007-2197 Fitting Assembly
46. MS27384-6C 4730-00-128-9819 Fitting Assembly
47. MS27384-8 4730-00-054-7635 Fitting Assembly
48. MS27385-4C 4730-00-057-0664 Fitting Assembly
49. MS27385-6C 4730-00-053-0380 Fitting Assembly

Table D-1. (Sheet 1 of 2)

D-65
TM 55-1520-210-23-3

ITEM
NUMBER PART NUMBER NSN NOMENCLATURE

50. MS27385-8C 4730-00-119-9854 Fitting Assembly


51. MS87018-10 4730-00-541-9105 Fitting Assembly
52. MS87018-12 4730-00-541-1957 Fitting Assembly
53. MS87018-16 4730-00-585-6212 Fitting Assembly
54. MS87018-4 4730-00-618-7378 Fitting Assembly
55. MS87018-6 4730-00-613-1859 Fitting Assembly
56. MS87018-8 4730-00-632-2002 Fitting Assembly
57. MS87019-12 4730-00-618-7382 Fitting Assembly
58. MS87019-4 4730-00-709-3887 Fitting Assembly
59. MS87019-8 4730-00-684-6394 Fitting Assembly
60. MS87020-10 4730-00-919-6785 Fitting Assembly
61. MS87020-12 4730-00-238-5338 Fitting Assembly
62. MS87020-4 4730-00-618-8862 Fitting Assembly
63. MS87020-6 4730-00-720-1166 Fitting Assembly
64. MS87020-8 4730-00-795-0945 Fitting Assembly
65. MS87021-16 4730-00-936-2364 Fitting Assembly
66. MS87022-16 4730-00-087-1016 Fitting Assembly
67. MS87023-16 4730-00-403-0886 Fitting Assembly
68. 624-7 5640-00-684-4153 Fire Sleeving
69. AE102-8 5640-00-568-4687 Fire Sleeving
70. 900902-4 4730-00-675-2450 Clamp
71. AE10187-001 8040-00-144-9774 Dow Corning 3140 RTU
72. QQ-V-423 9505-00-804-3814 Safety Wire .042 Dia.
73. MS87021-12 4730-00-936-2365 Fitting Assembly
74. MS87023-12 4730-00-087-1008 Fitting Assembly
75. MS87019-10 473-00-813-6923 Fitting Assembly

Table D-1. (Sheet 2 of 2)

D-66 Change 9
TM 55-1520-210-23-3

Hose Assembly Items Required for MS800 I E2 I OA 4, 3 8


Part Number Fabrication (Refer
to Table D-I for MS800 I E440A 4. 3 8
Items Listed) MWJOIFl50B 5, 3 9 . 4 5
MS800 I F200A 5, 39
MS8OOOE072A 4. 21
MWJOIF2IOA 5. 3 9
MS8OOOE I SOB 4. 2 I, 32
MS800 I G I308 6, 40. 46
MS8OOOE I60A 4, 21
MS800 I G I46A 6, 4 0
MS8OOOE I608 4, 2 I, 32
MSBX i G4ijOA 6, 40
MS8OOOE I65A 4. 21
MS800 I G44OA 6, 4 0
MS8OOOE I808 4. 21, 32
MS800 I H094C 69. 70. 7 I
M--F’
“W”.e”L..
’ , OA 4. 2!
MS800 I H I36H 7, 4 I, 4 7
MS8OOOE2 I OC 4. 21. 34
MS87028E I23A 12.54
MS8OOOE250C 4,21. 34
MS87028E2 I6A 4, 54
MS8fXXX38OA 4, 21
MS87028E220C 12, 54, 62
MS8OOOE320E I70 32, 4 MS87028G082COO 13, 55. 63
MS8OOOE324C 4.21, 34 MS87028G2 I OA 13,55
MS8OOOE340C 4,2l. 34 I
MS87028H090A 14.56
MS8OOOG070C 6, 22, 35 MS87028H IO6AOOO 14.56
MS8OOOG090C 6, 22, 35 MS87028H I I OC 14, 56, 64
MS80OOG I IOB 6. 22, 33 MS87028H ISOA 14,56
MS8OOOG I30A 6, 22 MS87028H I75A l4,56
MS8OOOG I308 6. 22, 35 MS87028H280C 14, 56, 6 4
MS8000G I8OC 6, 22. 35 MS87028H283COOO 14, 56, 6 4
MS8OOOG520F 6. 35 MS87028H700C 14, 56, 6 4
MS8OOOH2 I OA 7, 23 MS87028) I36A 9.51
MseOOOJ ! 9OF I, 28 MS87028J I66F 9, 60

MS8000J220C I . 17. 2 8 MS87028J I85FOOO 9, 60

I, 28 MS87028J336C 9, 5 I; 60
MS8OOOJ26OF
MS87028K I I6C IO. 73, 74
MWJOOK I308 2, 19, 26
MS87028K I46A IO, 52
MS8OOOK I3OC 2 , 19. 3 0
MS87028K I7 I B IO, 52, 57
MS8OOOK I 50E I80 2, 26, 30
1 MS87028K2 I4A IO, 52 I
MWIOOK I6OF ! 80 2. 30
! MS87028Y”“‘”
I LILA IO, 52 I
MS8000K700C 2 , 19, 30
MS87028K322E I40 IO. 57, 61
MS8OOOM2 I OG 3, 20
1 MS87028K360C IO, 52. 61
MS800 I E I40B 4, 38, 4 4
MS800 I E I50B 4, 38, 4 4
MS800 I E200A 4, 38

Table D-2.

Change 5 D-67
TM 55-1520-210-23-3

Hose Assembly Items Required for


Part Number Fabrication (Refer to
Table D-1 for Items
Listed)

70-009L000G116 69, 70, 71


70-010J000A180 14, 56
70-010J000A180 14, 56
70-010J000G214 14, 56, 64
70-010J000T164 14, 56, 59
70-010J000T174 14, 56, 59
70-010J000V384 14, 56, 64
70-010K000H154 9, 51, 75
70-010K304Z134 9, 60, 75
MS87028E124C 12, 54, 62

D-68 Change 9
TM 55-1520-210-23-3
l7JBEASSY FABRICATE STOCKDM. ENDF
PART NO. FROM NSN O.D. W.T. L
NUTNSN 1 Q=
I

204-040-215-27 4710-00-278-8726 3l8 .035 13 4730-00-142-2167 2 4730-00-595-3102 2 Lub.

204-040-722-1 4710-00-278-3291 ll4 .035 16 4730-00-222-1912 2 4730-00-278-0678 2 Lub.


I
204-04@-723-L 4710-00-278-3291 114 .035 16 473040-222-1912 2 4730-00-278-0678 2 Lub.
204a60-082- 1 4710-00-278-3291 lf4 .020 13 4730-w222-1912 2 4730-00-278-0678 1 2 1 M. 1
204-060-098-l 4710-00-278-3291 l/4 .035 7 4730.00-222-1912 2 4730-00-278-0678 1 2 1 Lub. 1
I

204-070-110-153 4710-00-278-6398 II4 .03s 6 4730-00-287-0289 2 4730-00.302-8641


I
2
Air
204-070-110-155 4710-00-278-6398 l/4 .035 7 4730-W-287-0289 2 4730-00-302-8641 1 2 ”
lnsr
204-070-110-3 47lo-oo-2784398 ll4 .035 18 4730-00-287-0289 2 4730-00-302-8641

204-070-110-65 4710-00-278-6398 I/4 .035 38 473600-287-0289 2 4730-00-302-8641

204-070-110-67 4710-00-278-6398 l/4 ,035 38 4730-00-287-0289 2 4730-00-302-8641

204-070-110-7 4710-00-278-6398 If4 .03S 24 4730-00-287-0289 2 4730-00-302-8641

204-070-110-71 471040-278-6398 l/4 .oss 12 4730-O&287-0289 2 4730-00-302-8641

204-070-134-11 4710-00-278-6398 114 .035 30 4730-00-287-0289 2 4730-00-302-8641

4710-00-278-6398 4730-00-302-8641

4710-00-278-6398 4730-00-302-8641
4730-00-302-8641 2
I
4710-00-278-6398 4730-00-302-8641
4730-00-302-8641 2

204-072-355-l 4710-00-278-6398
4710-00-278-6398 If4 ,035 14 4730-O&278-0289 2 4730-00-302-8641
4730-00-302-8641

204-072-364-I 4710-00-278-6398
4710-00-278-6398 114 .035 20 4730-00-278-0289 2 4730-00-302-8641
4730-00-302-8641 2

205-040-142-1 4710-00-278-8742 518 .035 16.5 4730-00-287-0290 2 4730-W-277-5358


4730-W-277-5358

205-040-143-1 4710-00-278-8742 98 .035 22.0 4730-00-287-0290 2 4730-00-277-5358


I I I I
2os-O40-144-l 4710-00-278-8742 5B .035 58.0 1 4730-00-287-0290 2 4730-00-277-5358

4710-00-278-8742

4710-00-278-8742 4730-00-277-5358 1 2 1 I
4710-00-278-8742 4730-00-277-5358
4710-00-278-8742 ,4730-00-277-5358 -+--I

Table D-3. (Sheet 1 of 6)

Change 8 D-68.1
TM 55-1520-210-233

D-68.2 Change 8
TM 55-1520-210-23-3

Table D-3. (Sheet 2 of 6)

Change 5 D-69
TM 55-1520-210-23-3

Table D-3. (Sheet 3 of 6)


D-70 Change 8
TM 55-1520-210-23-3

Table D-3. (Sheet 4 of 6)


D-71
TM 55-1520-210-23-3

TUBE ASSY FABRICATE STOCK DIM. END FITTING


PART NO. FROM NSN O.D. W.T. L NUT NSN QTY SLEEVE NSN QTY SYSTEM

205-076-136-1 4710-00-278-6398 ¼ 035 30 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.


205-076-138-1 4710-00-279-0950 ½ .035 16 4730-00-555-0595 2 4730-00-580-2120 2 Hyd.
205-076-140-1 4710-00-278-8726 3/8 .035 33 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-141-1 4710-00-278-3282 3/8 .035 26 4730-00-810-449 2 4730-00-554-7398 2 Hyd.

205-076-156-1 4710-00-278-6398 ¼ .035 33 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

205-076-137-1 4710-00-278-8726 3/8 .035 17 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.


205-076-158-1 4710-00-278-8726 3/8 .035 24 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.
205-076-159-1 4710-00-279-0950 1/2 .035 28 4730-00-555-0595 2 4730-00-580-2120 2 Hyd.

205-076-160-1 4710-00-278-6398 1/4 .035 29 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

205-076-161-1 4710-00-278-6398 1/4 .035 13 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

205-076-200-1 4710-00-278-6398 1/4 .035 9.0 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

205-076-201-1 4710-00-278-8726 3/8 .035 15 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.


205-076-202-1 4710-00-278-8726 3/8 .035 15 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.
205-076-203-1 4710-00-278-8726 3/8 .035 12 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-204-1 4710-00-278-8726 3/8 .035 24 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-205-1 4710-00-278-6398 1/4 .035 15.0 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

205-076-206-1 4710-00-278-6398 1/4 .035 19 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.


205-076-207-1 4710-00-278-3291 ¼ .035 16 4730-00-554-8015 2 4730-00-289-8619 2 Hyd.

205-076-208-1 4710-00-278-6398 ¼ .035 40.0 4730-00555-8203 2 4730-00-289-8619 2 Hyd.

205-076-209-1 4710-00-278-6398 ¼ .035 35 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.


205-076-210-1 4710-00-278-3291 ¼ .035 14 4730-00-554-8015 2 4730-00-289-8619 2 Hyd.
205-076-212-1 4710-00-278-3282 3/8 .035 26 4730-00-810-4499 2 4730-00-554-7398 2 Hyd.
205-076-213-1 4710-00-278-8726 3/8 .035 34 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.
205-076-214-1 4710-00-278-8726 3/8 .035 18 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-215-1 4710-00-278-8726 ¼ .035 30.0 4730-00554-7397 2 4730-00-554-7398 2 Hyd.

205-076-216-1 4710-00-278-8726 3/8 .035 20 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-217-1 4710-00-278-8726 3/8 .035 24 4730-00-554-7397 2 4730-00-554-7398 2 Hyd.

205-076-221-1 4710-00-278-6398 ¼ .035 52.0 4730-00-565-8203 2 4730-00-289-8619 2 Hyd.

205-076 -223-1 4710-00-278-6398 ¼ .035 12 4730-00-555-8203 2 4730-00-289-8619 2 Hyd.

Table D-3. (Sheet 5 of 6)

D-72
TM 55-1520-210-23-3

Table D-3. (Sheet 6 of 6)

D-73
TM 55-1520-210-23-3

Table D-4. (Sheet 1 of 20)

D-74 Change 8
TM 55-1520-210-23-3

Table d-4. (Sheet 2 of 20)


Change 4 D-75
TM 55-1520-210-23-3

Table D-4. (Sheet 3 of 20)

D-76 C h a n g e 4
TM 55-1520-210-23-3

BEND DIMENSION “A” BEND DIAL


PART NO. FROM “Y” END RADIUS SETTING BEND ANGLE END FITTING
NUMBER DIMENSION TYPE END TYPE END PRESSURE AND
"B" “Y” -X- TEST NOTES

205-060-590-1 1 1½ 1 0 83 Y - AN818-6D
2 9 5/8 1 165 85 MS20819-6D
3 14 5/16 1 50 85 X - Scarf Dial
4 17 ¼ 1 230 90 Setting 235
5 21 ¼ 1 230 25
6 24 5/8 1 50 22
7 31¼ 1 155 15
8 40 ½ 1 50 37
9 42 ¾ 1 235 45
47 3/8 III N/A
V
205-060-591-1 1 1 1 0 80 Y - AN818-6
6 5 16 I I N/A MS20819-6
X - AN818-6
MS20819-6

205-060-592-1 1 15/16 1 0 70 Y - AN818-6


2 12 7/16 1 75 50 MS20819-6
14¼ I I N/A X - AN818-6
MS20819-6

205-060-593-1 1 11¼ I o 15 Y - AN818-6


2 13¼ 1 180 15 MS20819-6
3 15¼ 1 270 76 X - AN818-6
30 9/16 1 I N/A MS20819-6

205-060-594-1 1 2¾ 1¾ o 82 Y - AN818-12
2 16. 3/8 1¾ 210 78 MS20819-12
3 22 ½ 1¾ 280 67 X - AN818-12
4 31¾ 1¾ 357 52 MS20819-12
36¼ I 1 100 psi

205-060648-1 8 7/16 1½ 0 28 Y - AN818-10D


2 11 7/16 1½ 180 28 MS20819-10D
3 20 1/16 1½ 270 8 X - AN818-10D
4 28 1/16 1½ 180 8 MS20819-1OD
5 30 5/16 1½ o 8
33 1/16 I I 35 psi

205-060649-1 1 8 1/8 1½ O 28 Y - AN818- 10D


2 11 1/8 1½ 180 28 MS20819-10D
3 19 5/8 1½ 290 12 x - AN818-10D
4 28 1/8 1½ 200 8 MS20819-10D
5 30 5/16 1½ 20 8
33 7/16 I I 35 psi

205-060-690-1 1 2 11/16 1 0 25 Y - AN818-6D


2 4 3/16 1 180 62 MS20819-6D
3 7 7/16 1 0 32 X - Scarf Dial
4 26 11/16 1 30 46 Setting 210
5 29 7/16 1 210 46
43 13/16 III v N/A

205-060-691-1 1 2 1¾ o 61 Y - AN818-12D
2 6 1¾ 180 60 MS20819-12D
3 13 5/8 1¾ 270 12 X- AN818-12D
4 16 3/16 1¾ 90 12 MS20819-12D
18 3/8 I I N/A

Table D-4. (Sheet 4 of 20)

Change 4 D-77
TM 55-1520-210-23-3

BEND DIMENSION -A- BEND DIAL


PART NO FROM "Y" END RADIUS SETTING BEND ANGLE END FITTING
NUMBER PRESSURE AND
“B" “X" TEST NOTES

205-070-436-1 1 2 5/16 9/16 0 49 Y- AN818-4D


2 4 7/16 9/16 180 49 MS20819-1D
3 15 7/16 9/16 180 90 X - AN818-4D
4 18 9/16 330 90 MS20819-4D
5 19 3/8 9/16 60 25
21 ¾ III III N/A

205-070-439-1 1 3½ 9/16 0 45 Y - AN818-4D


2 7 3/16 9/16 180- 43 MS20819-4D
11 1/14 III III 35 psi X - AN818-4D
MS20819-4D

205-070-440-1 1 2 9/16 9/16 0 9 Y- AN818-4D


2 17 11/16 9/16 180 8 MS20819-4D
30 15/16 III III N/A X - AN818-4D
MS20819-4D

205-070-441-1 1 1 1/16 9/16 0 90 Y - AN818-4D


2 3 9/16 0 40 MS20819-4D
3 5 5/16 9/16 180 40 x - AN818-4D
4 8 9/16 90 45 MS20819-4D
9 7/8 III III 35 psi
205-070-448-1 1 2 3/8 9/16 0 180 Y - AN818-4D
2 5 1/8 9/16 180 90 MS20819-4D
7½ III III 35 psi X - AN818-4D
MS20819-4D

205-070-475-1 1 3½ 9/16 0 20 Y - AN818-4D


2 7 5/8 9/16 105 83 MS20819-4D
3 9 1/8 9/16 260 62 X - AN818-4D
4 11 5/16 9/16 240 88 MS20819-4D
5 13 7/8 9/16 55 86
6 17 9/16 328 14
7 20 1/8 9/16 148 15
8 26 13/16 9/16 53 13
9 28 3/8 9/16 233 13
33 5/8 III III 35 psi

205-070-476-1 1 1 1/8 9/16 0 20 Y - AN818-4D


2 2 9/16 916 180 25 MS20819-4D
9 3/8 III III 35 psi X - AN818-4D
MS20819-4D

205-070-484-1 1 1 1/8 9/16 0 52 Y - AN818-4D


2 2¾ 9/16 180 78 MS20819-4D
3 14¼ 9/16 315 24 X - AN818-4D
15 7/8 III III 150 psi MS20819-4D

205-070-435-1 1 2 3/8 916 0 180 Y - AN818-4D


2 4 15/16 9/16 180 90 MS20819-4D
7 7/16 III III N/A X - AN818-4D
MS20819-4D

205-070-486-1 1 1¾ 9/16 0 50 Y - AN818-4D


2 4½ 9/16 180 50 MS20819-4D
3 16 3/16 9/16 160 38 X - AN818-4D

Table D-4. (Sheet 5 of 20)

D-78 Change 4
TM 55-1520-210-23-3

Table D-4. (Sheet 6 of 20)

Change 8 D-79
TM 55-1520-210-23-3

Table D-4. (Sheet 7 of 20)

D-80 Change 8
TM 55-1520-210-23-3

Table D-4. (Sheet 8 of 20)


Change 4 D - 8 1
TM 55-1520-210-23-3

BEND DIMENSION "A" BEND DIAL


PART NO. FROM “Y" END RADIUS SETTING BEND ANGLE END FITTING
NUMBER AND
“H“ “Y” “X" TEST NOTES
3 14 13/16 1 178 91 X- AN818-6D
4 23¼ 1 90 92 MS20819-6D
26 III III N/A

205-061-659-1 1 3 5/8 1¼ 0 26 Y- AN818-8D


2 6 9/16 1¼ 180 26 MS20819-8D
11 13/16 1 I 60 psi X - AN818-8D
MS20819-8D
205-061-661-1 1 5½ 1 0 33 Y - AN818-6D
2 7¾ 1 180 33 MS20819-6D
3 15¼ 1 197 89 X - AN818-6D
22¼ III III 60 psi MS20819-6D
205-061-662-1 1 4¾ 1 0 90 Y - AN818-6D
10¾ III III 60 psi MS20819-6D
X - AN818-6D
MS20819-6D

205-061-663-1 1 1 1¼ 0 90 Y - AN818-8D
2 11 1/16 1¼ 0 37 MS20819-8D
3 14¾ 1¼ 180 37 X - AN818-8D
4 22¾ 1¼ 230 62 MS20819-8D
5 25 1/8 1¼ 50 67
27¼ 1 I 35 psi

205-061-664-1 N/A (STRAIGHT TUBE) Y - AN818-8D


13½ 1 1 60 psi MS20819-8D
X - AN818-8D
½ MS20819-8D
205-061-668-1 1 2¾ 1¼ 0 90 Y - AN818-8D
2 8¼ 1¼ 265 10 MS20819-8D
10 3/8 1 I 80 psi X - AN818-8D
MS20819-8D

205-061-669-1 1 1 7/16 1¼ O 83 Y - AN818-8D


2 7 11/16 1¼ 164 79 MS20819-8D
3 11¾ 1¼ 254 15 X - AN818-8D
13 15/16 1 I 100 psi MS20819-8D

205-061-670-1 1 1¾ 1¼ 0 36 Y - AN818-8D
2 3½ 1¼ 175 38 MS20819-8D
3 9½ 1¼ 265 19 X - AN818-8D
4 13 11/16 1¼ 175 26 MS20819-8D
5 16¼ 1 ¼ 352 26
6 24 9/16 1¼ 10 30
7 27 1¼ 155 26
8 3 17/16 1¼ 340 12
9 32¾ 1¼ 160 14
33 15/16 1 1 100 psi

205-061-671-1 1 2 1¼ 0 135 Y - AN818-8D


2 8 11/16 1¼ 185 88 MS20819-8D
3 13½ 1¼ 275 35 X - AN818-8D
4 13 3/8 1¼ 25 48 MS20819-8D
29 15/16 1 1 100 psi

Table D-4. (Sheet 9 of 20)

D-82 Change 4
TM 55-1520-210-23-3

Table D-4. (Sheet 10 of 20)

Change 4 D-83
TM 55-1520-210-23-3

Table D-4. (Sheet 11 of 20)

D-84 Change 4
TM 55-1520-210-23-3

Table D-4. (Sheet 12 of 20)


[ALL DATA ON SHEET 13 OF 20 (PAGE D-86) HAS BEEN DELETED]

Change 8 D-85/(D-86 blank)


TM 55-1520-210-23-3

Table D-4. (Sheet 14 of 20)

Change 4 D-87
TM 55-1520-210-23-3

Table D-4. (Sheet 15 of 20)

D-88 Change 4
TM 55-1520-210-23-3

Table D-4. (Sheet 16 of 20)

Change 4 D-89
TM 55-1520-210-23-3

DIMENSION “A” BEND DIAL


BEND NO. BEND ANGLE END FITTING
FROM “Y” END RADIUS SETTING
PART NUMBER AND
DIMENSION TYPE END TYPE END PRESSURE NOTES
“B” “Y” “X” TEST

205-076-231-1 1 17 1/2 1 1/2 0 33 Y - MS21921D8


2 11 1/2 1 1/2 90 90 MS21922-8
3 6 1 1/2 145 90
X - MS21921D8
4 3 1 1/2 45 33
MS21922-8
21 1/2 IV IV 3000
205-076-232-1 1 133/4 15/16 0 128 Y - MS21921D6
2 8 1/2 15/16 280 72 MS21922-6
3 5 5/8 15/16 38 47
X - MS21921D6
4 31/4 15/16 270 89
MS21922-6
IV IV 3000
205-076-233-1 1 2 3/16 9/16 0 43 Y - MS21921-4D
2 5 11/16 9/16 180 43 MS21922-4
3 9 5/8 9/16 183 37
X - Scarf Dial
4 15 1/8 9/16 3 36
Setting 151
5 243/4 9/16 241 12
6 271/4 9/16 61 13
7 36 13/16 9/16 61 61
8 38 1/2 9/16 241 63
40 5/8 IV V N/A
205-076-235-1 1 293/4 1.0 0 26 Y - MS21919-6D
2 28 3/8 1.0 179 24 MS21922-6
3 20 7/8 1.0 225 59
X - MS21919-6D
4 19 1.0 321 37
MS21922-6
5 17 3/8 1.0 76 59
6 11 5/8 1.0 151 31
7 9 7/16 1.0 332 35
8 3 15/16 1.0 359°30” 23°30”
9 2 3/16 1.0 177°30” 22
31.44 I 3000 psi
205-076-236-1 1 1 15/16 0 15 Y - MS21921-6D
2 41/4 15/16 270 90 MS21922-6
3 71/4 15/16 355 25 X - MS21921-6D
9 1/8 IV IV 1500 psi MS21922-6
205-076-237-1 1 3 1/16 1 0 37 Y - MS21921-6D
MS21922-6
2 7 1/2 1 12 54
X - MS21921-6D
9 5/8 IV IV 1500 psi MS21922-6
205-076-238-1 1 5 3/16 1 0 90 Y - MS21921-6D
2 10 7/8 1 7 90 MS21922-6
3 173/4 1 240 8 X - MS21921-6D
19 7/8 IV IV 1500 psi MS21922-6
205-076-240-1 1 1 1/8 1 0 5 Y - MS21921-6D
2 9 3/8 1 270 88 MS21922-6
3 13 7/16 1 358 52
X - MS21921-6D
4 17 1 178 52
MS21922-6
5 19 1/2 1 146 90
6 221/4 1 236 35
7 25 11/16 1 322 86
8 331/4 1 218 30
9 34 7/8 1 38 30
37 1/8 IV IV 1500 psi

Table D-4. (Sheet 17 of 20)

D-90 Change 9
TM 55-1520-210-23-3

Table D-4. (Sheet 18 of 20)

Change 4 D-90.1
TM 55-1520-210-23-3

Table D-4. (Sheet 19 of 20)

D-90.2 Change 4
TM 55-1520-210-23-3

Table D4.(Sheet 19 of 20)

Change 8 D-90.3/(D-90.4 blank)


TM 55-1520-210-23-3
Figure D-43. Part Number 28D00 PLATE, RETAINER
Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick
D-91
TM 55-1520-210-23-3

Figure D-44. Part Number 49C16 LINK, VALVE ASSEMBLY


Fabricate from: NSN 9515-00-234-7953
Material: Metal Sheet - Steel, Corrosion Resistant Cold Roll,
Federal Sepcification MIL-S-5059A, 0.063 Inch Thick

D-92
TM 55-1520-210-23-3

Figure D-45. Part Number 50H1 Lightening Hole Pattern

D-93
TM 55-1520-210-23-3

Figure D-46

D-94
TM 55-1520-210-23-3

DIMENSIONS IN INCHES: UNLESS OTHERWISE SPECIFIED


TOLERANCES: THREE
PLACE DECIMALS ±.005

Figure D-47. Part Number 59H21 HOLE PATTERNS

D-95
Figure D-48
TM 55-1520-210-23-3

SEAL, PART NUMBERS 205-031-669-151


205-031-669-152
FABRICATE FROM NSN 9390-00-456-2095

Figure D-49.

SEAL, PART NUMBER 205-060-907-35


FABRICATE FROM NSN 9390-00-851-9178

Figure D-50.

GASKET, PART NUMBER 205-060-907-37


FABRICATE FROM NSN 5330-00-938-1719

Figure D-51.

D-97
TM 55-1520-210-23-3

Figure D-52. Part Number BYRF572 SCREW, MACHINE


Fabricate from: NSN 5305-00-579-4554

D-98
TM 55-1520-210-23-3

NOTE:
MAY BE USED AS AN ALTERNATE FOR BELL STANDARD
50H1 LIGHTENING HOLES DASH NUMBER FOR DASH
NUMBER WITHIN MATERIAL LIMITS SHOWN. (MATERIAL
SHOULD BE IN “0” INITIAL CONDITION. )

Figure D-53. Part Number 70-017 HOLE PATTERNS

218-261 0 - 88 -8 D-99
TM 55-1520-210-23-3

Figure D-54. Part Number SP 401-1 PIN, Shoulder


SP 401-2
Fabricate from: NSN 9530-00-167-1817
Material: Wire Non-Electric Nickel Annealed Cold,
Federal Specification MIL-N-6710, Cond A, 0.250 Inch Dia.

D-100
TM 55-1520-210-23-3

B79C65

MATERIAL: 5/16 O.D. x .058 WALL NOTE:


THICKNESS TYPE 1. REMOVE ALL BURRS
6061 AL. ALY. TUBING
PER WW-T-789

Figure D-55. Part Number B79C65 SPACER


Fabricate from: NSN 5340-00-727-1891
Material: Spacer, Sleeve Aluminum Alloy. 0.194 inch ID. 0.322 inch O.D. 20 inch long.

D-101
TM 55-1520-210-23-3

Figure D-56. Part Number B56C21 COVER ASSEMBLY


Fabricate from: NSN 9535-00-167-2280
NSN 5305-00-253-5604
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, 0.040 Inch Thick.

D-102
TM 55-1520-210-23-3

NOTES:
1. MUST BE FREE OF BURRS
2. ALODIZE MIL-C-5541 (1)

Figure D-57. Part Number NYLC3, COVER PLATE, Access


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-103
TM 55-1520-210-23-3

SP 469-1 SP 469-2

Figure D-58. Part Number SP 469-1 POST, Micro Switch


Fabricate from: -NSN 9530-00-167-1817
Material: Wire, Nonelectric Nickle Annealed, Federal Specification M16-N-6710,
Cond A, 0.250 Inch Dia.

D-104
TM 55-1520-210-23-3

Figure D-59. Part Number SP 516 BUSHING, Solenoid


Fabricate from: NSN 9530-00-167-1818
Material: Metal Rod-Nickel, Cold Finish Annealed, Federal Specification
MlL-N-6710, 0.375 Inch Dia.

D-105
TM 55-1520-210-23-3

NOTES:
1. BREAK ALL SHARP EDGES .005 TO 0.10
2. CAD. PLATE QQ-P-416 TYPE 1 CLASS A

Figure D-60. Part Number SP 1152-2 SUPPORT, Spring


Fabricate from: NSN 9510-00-294-9660
Material:

D-106
TM 55-1520-210-23-3

Figure D-61. Part Number SP 1699-1 PIN, Solenoid Shaft


Fabricate from: NSN 9510-00-294-9666
Material: Metal Bar - Steel Cold. Federal Specification MlL-S-6758, 4130 Comp, 0.375 Inch Dia.

D-107
TM 55-1520-210-23-3

Figure D-62. Part Number SP 1705-1 PIN, Solenoid


Fabricate from: NSN 9510-00-224-1675
Material:

Figure D-63. Part Number SP 1706-1 SPACER


Fabricate from: NSN 9530-00-167-2026
Material:

D- 108
TM 55-1520-210-23-3

SP-1707-1 SP1707-2

Figure D-64. Part Numbers SP 1707-1 AND -2, PIN, Solenoid Linkage
Fabricate from: NSN 9510-00-294-9666
Material: Metal Bar - Steel, Cold Finish. Federal Specification MlL-S-6758,
Comp 4130, 0.375 Inch Dia.

D-109
TM 55-1520-210-23-3

NOTES:
1. DIM’S ARE BEFORE PLATE
2. HEAT TREAT TO ROCKWELL C-25-29
3. CAD. PLATE QQ-P-416 CC. 2 TYPE II

Figure D-65. Part Number SP 1709-2 PIN, Shaft & Arm


Fabricate from: NSN 9510-00-294-9666
Material: Metal-Bar Steel Cold Finished, Federal Specification MIL-S-6758,
Comp 4130, 0.375 Inch Dia.

D-110
TM 55-1520-210-23-3

NOTES:
1. BREAK ALL SHARP EDGES 0.005 TO 0.010
2. HEAT TREAT MATERIAL TO ROCKWELL C-25 TO 29
3. CAD. PLATE QQ-P-416 CLASS 2 TYPE II

SP 1710-1 LINK SOLENOID


Figure D-66. Part Number
Fabricate from: NSN 9515-00-184-8811
Material: Metal Strip Steel, Hot Rolled. Federal Specification MlL-S-18729
Comp 4130, 0.125 Inch Thick

D-111
TM 55-1520-210-23-3

Figure D-67. Part Number SP 1715-1 PIN, Stop


Fabricate from: NSN 9510-00-618-8926
Material:

D-112
TM 55-1520-210-23-3
Figure D-68. P a r t N u m b e r SP 3184-4 DOWEL PIN
SP 3184-5
SP 3184-6
Fabricate from: NSN 9510-00-596-2016 D-113
Material:
TM 55-1520-210-23-3

Figure D-69. Part Number 20-036-8-24, BRAID, Wire


Fabricate from: NSN 6145-00-628-7753
Material:

D-114
TM 55-1520-210-23-3
Figure D-70. Part Number 99C29, TUBE, Valve to Valve
F a b r i c a t e f r o m : NSN 4710-00-278-6398
NSN 4730-00-287-0289
NSN 4730-00-302-8641
D-115
Tube Aluminum Allow, Federal Specification WW-T-700/4, 1/4 Inch Diameter OD, 0.035 Inch Wall Thickness
TM 55-1520-210-23-3

Figure D-71. Part Number AN919-1D (CAGE 88044) REDUCER TUBE


Fabricate from: NSN 4730-00187-3575
Finish: Hex Surface 25
Anodize per MIL-A-8625 Or
Chem Film Per MIL-C-55541
(Light Blue Dye).
Material:

D-116 Change 8
TM 55-1520-210-23-3

Figure D-72. Part Number 204-011-149-1 CLAMP, Strap Retention Nut Main Rotor
Fabricate from: NSN 9515-00-204-0220
Material: Steel Sheet, Federal Specification MlL-S-18729, Condn, 0.125 Inch Thick

D-117
TM-55-1520-210-23-3

Figure D-73. Part Number 024-011-458-1 SWASHPLATE


204-011-458-3
204-011-458-5
204-011-458-7
Fabricate from: NSN 9535-00-232-0418
Material: 2024 AL ALY Sheet, Federal Specification
QQ-A-250/5, T3, 0.125 Inch Thick

D-118
TM 55-1520-210-23-3

Figure D-74. Part Number 204-012-110-1 BOLT


Fabricate from: NSN 5306-00-182-2010
Material: 4130 STL/MIL-S-6758 HT-125-145KSI
Cad Plate CB1

D-119
TM 55-1520-210-23-3

Figure D-75. Part Number 204-030-800-443 Cover Tail Boom Assembly


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Federal Specification QQ-A-250/5, 0.0250 Inch Thick

D-120
TM 55-1520-210-23-3

Figure D-76. Part Number 204-030-437-3 SPRING


Fabricate from: NSN 9515-00-684-6944
NSN 5325-00-141-4002
NSN 5325-00-721-5503
Material: Metal Strip Steel Hot Rolled, Federal Specification MIL-S-7947,
0.020 Inch Thick

D-121
TM 55-1520-210-23-3

Figure D-77. Part Number 204-031-003-13,-14 Rubber Seal


Fabricate from: NSN 9320-00-759-9758
Material: LG. Rubber, 105.0 Inch Length

D-122
TM 55-1520-210-23-3

204-031-003-23 5340-00-949-8281

Figure D-78.
D-123
TM 55-1520-210-23-3

Figure D-79. Part Number 204-031-139-3 BRACKET ASSY


Fabricate from: NSN 9535-00-085-9729, 4 EA 5310-00-778-9480
Material: 2024 AL ALY Federal Specification QQ-A-250/5,
0.032 Inch Thick

D-124
TM 55-1520-210-23-3

Figure D-80. Part Number 204-031-251-1 COVER PLATE, Antenna Cutout


Fabricate from: NSN 9535-00-086-9789
Material: 2024 AL ALY Federal Specification QQ-A-250/5,
0.032 Inch Thick

D-125
TM 55-1520-210-23-3
D-126 Figure D-81.
TM 55-1520-210-23-3

Figure D-82. Part Number 204-040-732-I Strap, Support


Fabricate from: NSN 9515-00-683-9294 on
P/N204-040-732-I Clip
Material: Metal Strip Steel, Federal Specification MIL-S-7947, 0.020 Inch Thick

D-127
TM 55-1520-210-23-3

Figure D-83. DELETED

D-128 Change 5
TM 55-1520-210-23-3

Figure D-84. Part Number 204-060-031-15 RESTRICTOR, Fitting


Fabricate from: NSN 9510-00-243-7626 and 4730-00-231-3026
Material:

D-129
TM 55-1520-210-23-3

Figure D-85. Part Number 204-060-056-1 NUT, Pressure Switch Support


Fabricate from: NSN 5310-00-208-5769
Material: Steel, Cadmium Plated

D-130
TM 55-1520-210-23-3

Figure D-86. Part Number 204-070-175-1 MOUNT, Valve Control, Heating


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

218-261 0 - 88 -9 D-131
TM 55-1520-210-23-3

Figure D-87. Part Number 204-070-185-1 CONNECTOR, Valve Selector, Bleed Air
Fabricate from: NSN 1660-00-736-1007
Material: Adapter, Aluminum Alloy Casting

D-132
TM 55-1520-210-23-3

Figure D-88. Part Number 204-070-230-1 BRACKET, Valve, Heating and Bleed Air
Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-133
TM 55-1520-210-23-3

204-070-255-3 NAS697A3 MS20426AD3

Figure D-89. Part Number 204-070 -255-1 & 2 BRACKET, Map & Data Case

D-134
TM 55-1520-210-23-3

Figure D-90. Plate, Structural, Aircraft, PN ES-B-220316


Fabricate from: NSN 9535-00-232-0565
Material: .032 x 3 x 3 AL ALY, 2024-T3, QQ-A-250/5

D-135
TM 55-1520-210-23-3

Figure D-91. Access Panel, Assy PN ES-D-221175


Fabricate from: NSN 9535-232-1882
Material: AL ALY, sheet, .063 THK., 6061-T6, QQ-A-250/11

D-136
TM 55-1520-210-23-3

Figure D-92. Part Number 204-070-274-1 LINK, Control to Bellcrank, Defrost


Fabricate from: NSN 9535-00-232-0418
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5, 0.125 Inch Thick

D-137
TM 55-1520-210-23-3

Figure D-93. Part Number 204-070-275-1, BELLCRANK, Heating and Defrost Control
Fabricate from: NSN 9535-00-232-0418
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A 250/5, 0.125 Inch Thick

D-138
TM 55-1520-210-23-3

Figure D-94. Part Number 204-070-528-1 COVER ASSEMBLY, Cargo Hook Mirror

D-139
TM 55-1520-210-23-3

Figure D-95. Part Number 204-070-583-1 BRACKET, Upper Switch


Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362,
0.050 Inch Thick

D-140
TM 55-1520-210-23-3

Figure D-96. Part Number 204-070.585-1 BRACKET, Lower Switch Bleed Air & Heating
Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY, Sheet Federal Specification, QQ-A-362.
0.050 Inch Thick

D-141
TM 55-1520-210-23-3

Figure D-97. Part Number 204-070-749-1 BRACKET INSTRUMENT


Fabricate from: NSN 9535-00-232-0501
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.050 Inch Thick

D-142
TM 55-1520-210-23-3

Figure D-98. Part Number 204-071-539-3 STOP, Emergency Jettison


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-143
TM 55-1520-210-23-3

PART NUMBER FABRICATE FROM NSN DIM A OD NOTES


204-071-577-1 4710-00-278-8727 8.50 5/16 2,3,4
205-072-222-1 4710-00-279-0910 15.25 5/8 2,3,4

NOTES:
1. DOUBLE FLARE ENDS OF TUBE PER TM 55-405-7 MANUAL.
2. SINGLE FLARE ENDS OF TUBE PER TM 55-405-7 MANUAL.
3. APPLY A CHEMICAL FILM NSN 8030-00-829-0376 PER TM 55-405-3 MANUAL.
4. APPLY ONE COAT ZINC CHROMATE PRIMER NSN 8010-00-899-8825 IMMEDIATELY FOLLOWING
APPLICATION OF CHEMICAL FILM ALLOWING TIME FOR DRYING BETWEEN COATS.

Figure D-99.

D-144
TM 55-1520-210-23-3

Figure D-100. Part Number 204-072-054-1, BRACKET, Compass


Fabricate from: NSN 9535-00-232-0418
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.125 Inch Thick

D-145
TM 55-1520-210-23-3

Figure D-101. Part Number 204-072-083-1 BOLT, Cargo Mirror


Fabricate from: NSN 5306-00-182-2009
Material:

Figure D-102. Part Number 204-075-160-1 PAD, Battery Sump Jar


Fabricate from: NSN 8305-00-191-1101
Material: Felt Sheet, Grey Non-woven, Federal Specification C-F-2026
Type 1, 0.50 Inch Thick, 1.0 Inch Wide

D-146
TM 55-1520-210-23-3

Figure D-103. Part Number 204-075-520-1, PLATE, Assy Mounting


Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-147
TM 55-1520-210-23-3

Figure D-104. Part Number 204-076-032-3 BRACKET


Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362,
0.050 Inch Thick

D-148
TM 55-1520-210-23-3

Figure D-105. Part Number 205-001-104-1, SHIM, Bellcrank


Support Collective Controls
Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-149
TM 55-1520-210-23-3

Figure D-106. Part Number 205-030-007-77 D O O R


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY, Sheet, Federal Specification QQ-A-250/5 0.032 Inch Thick

D-150
TM 55-1520-210-23-3

Figure D-107. Part Number 205-030-007-97, DOOR, Left Hand (Shown)


205-030-007-98, DOOR, Right Hand, (Opp)
Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-151
TM 55-1520-210-23-3

Figure D-108. Part Number 205-030-007-99, DOOR


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-152
TM 55-1520-210-23-3

Figure D-109 Part Number 205-030-007-107, DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-153
TM 55-1520-210-23-3
Figure D-110. P a r t Number 205-030-007-109,DOOR
Fabricate from: NSN 9535-00-167-2279
M a t e r i a l : 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick
D-154
TM 55-1520-210-23-3

Figure D-111. Part Number 205-030-007-111 DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification
QQ-A-250/5, 0.032 Inch Thick

D-155
TM 55-1520-210-23-3

Figure D-112. Part Number 205-030-007-113, DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D- 156
TM 55-1520-210-23-3

Figure D-113. Part Number 205-030-007-131, DOOR, Left Hand (Shown)


DOOR, Right Hand (Opp)
Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-157
TM 55-1520-210-23-3

Figure D-114. Part Number 205-030-007-133 DOOR, Left Hand (Shown)


205-030-007-134 DOOR, Right Hand (Opp)
Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-158
TM 55-1520-210-23-3

Figure D-115. Part Number 205-030-007-155 COVER


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-159
TM 55-1520-210-23-3

Figure D-116. Part Number 205-030-007-157, COVER


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-160
TM 55-1520-210-23-3

Figure D-117. Part Number 205-030-007-159, DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-161
TM 55-1520-210-23-3

Figure D-118. Part Number 205-030-007-179, DOOR, Left Hand Shown


205-030-007-180, DOOR, Right Hand Opp.
Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQA-250/5, 0.025 Inch Thick

D-162
TM 55-1520-210-23-3

Figure D-119. Part Number 205-030-007-231 DOOR


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
0.025 Inch Thick

D-163
218-261 0 - 88 -10
TM 55-1520-210-23-3

Figure D-120. Part Number 205-030-007-233, D O O R


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification, QQ-A-250/5, 0.025 Inch Thick

D-164
TM 55-1520-210-23-3

Figure D-121. Part Number 205-030-007-245, DOOR, Left Hand (Shown)


205-030-007-246, DOOR, Right Hand (OPP)
Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-165
TM 55-1520-210-23-3

Figure D-122. Part Number 205-030-007-271, DOOR, Left Hand (Shn)


205-030-007-272, DOOR, Right Hand (Opp)
Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-166
TM 55-1520-210-23-3

Plate, Cover-Rearward PN 1951-1-3109


Figure D-123.
Fagricate from: N S N 9 5 3 5 - 0 0 - 0 8 4 - 4 4 4 8
Material: .063 THK AL ALY, SH6061-T6, QQ-A-250/11

D-167
TM 55-1520-210-23-3

Figure D-124. Part Number 205-030-007-341 DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-168
TM 55-1520-210-23-3

Figure D-125. Part Number 205-030-007-351 DOOR


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-169
TM 55-1520-210-23-3

Figure D-126. Part Numbers 205-030-028-5 DOOR ASSEMBLY


205-030-028-6
206-030-028-25
205-030-028-27
Fabricate from: NSN 9535-00-167-2279
NSN 9330-00-576-3984
NSN 5340-00-661-8140
Material: 2024 AL ALY Sheet, Federal
Specification QQ-A-250/5,
0.025 Inch Thick
Hinge Butt,
Aluminum Alloy
Make From MS200001P3-
D-170
7200 Material
TM 55-1520-210-23-3

Figure D-127. Part Number 205-030 -031-7 DOOR ASSEMBLY


Fabricate from: NSN 9535-00-167-2279
NSN 9330-00-260-3806
NSN 5340-00-664-8140
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick
Plastic Sheet Phenolic, Federal Specification MlL-D-1503S, 0.250 Inch Thick
205030-2002

Figure D-127.1. Part Number: 204-011-213-101, Hub Spring Main Rotor Shim

Fabricate From:
Material: Cres shim, MIL-S-22499 Comp 3
TY1 , CL2
Thickness 0.0900
Width 2.000 204011-2053
Length 5.0 204-011-213-101

Change 1 D-171
TM 55-1520-210-23-3

Figure D-128. Part Number 204-011-461-1 BOLT, SWASHPLATE


Fabricate from: NSN 5306-00-639-2277
Material: Bolt Shear Steel, Make from NAS 464-5-20

Figure D-129. Part Number 205-030-247-25 COVER PLATE


Fabricate from: NSN 9533-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
0.025 Inch Thick

D-172
TM 55-1520-210-23-3

Figure D-130. Part Number 205-030-302-5 & -6, SUPPORT, Stop Cargo Door
Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-25/5, 0.040 Inch Thick

D-173
TM 55-1520-210-23-3

Figure D-131. Part Number 205-030-309-13, COVER


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-174
TM 55-1520-210-23-3

Figure D-132. Part Number Tube NSN Nut NSN Sleeve NSN
205-030-431-1 4710-00-279-0955 4730-00-142-2167 4730-00-278-6070
205-030-432-1 4710-00-279-0955 4730-00-142-2167 4730-00-276-6070
205-040-130-1 4710-00-279-0955 4730-00-142-2167 4730-00-276-6070

Change 4 D-175
TM 55-1520-210-23-3
D-176 Figure D-133.
TM 55-1520-210-23-3

Figure D-134 Part Number: 110-119-1


Fabricate from: NSN 9390-00-622-4420
Material: Extrusion—Rubber

Figure D-135
Part Number: UH-1 S0054-1
Fabricate from: NSN 9510-00-056-1916
Material: Metal bar steel, QQ-S-763, class 310
Hot Rolled Annealed, 0.5 inch diameter

Grind O.D to provide an interference fit of 0.0001 to 0.0003 to fill


existing reamed out hole with maximum diameter of 0.3594 plus 0.000
minus 0.001.

D-177
TM 55-1520-210-23

Figure D-136. Part Number 205-030-543-17 SPACER


Fabricate from: NSN 5340-00-809-9379
Material: Spacer, Sleeve, Aluminum Alloy, Make from
NAS 43DD3-51 Spacer

Figure D-137. Part Number 205-030-614-13 CHANNEL


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
TEMP T3, 0.032 Inch Thick

D-178
TM 55-1520-210-23-3

Figure D-138. Part Number 205-030-671-7 BRACKET


205-030-671-9
Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
TEMP O H.T. T42, 0.040 Inch Thick

D-179
TM 55-1520-210-23-3

Figure D-139. Part Number 205-030-737-3 BRACKET


Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
Temp 0 T42, 0.040 Inch Thick

D-180
TM 55-1520-210-23-3

Figure D-140. Part Number 205-030-737-5 SPACER


Fabricate from: NSN 9330-00-290-3462
Material: Phenolic cotton fabric MlL-P-15035,
Type FBM 0.1875 x 0.70 x 1.8

D-181
TM 55-1520-210-23-3
D-182 Figure D-141.
TM 55-1520-210-23-3

Figure D- 142. Part Number 100-057-I BACK-UP PLATE ASSY


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
T3, 0.032 Inch Thick
Stud-Snap Fastener, Metal (AN227-8B, Color Black)

Change 5 D- 183
TM 55-1520-210-23-3

Figure D- 143. Part Number 100-057-5 BACK-UP PLATE ASSY


Fabricate from: NSN 9535-00-167-2279
NSN 5325-00-174-2923
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
T3, 0.032 Inch Thick
Stud-Snap Fastener, Metal (AN227-8B, Color Black)

D- 184 Change 5
TM 55-1520-210-23-3

Figure D-144. Part Number 205-030-849-7 HINGE, Half


Fabricate from: NSN 5340-00-993-1461
Material: Leaf Butt Hinge, Aluminum, 0.040 Inch Thick,
Make from MS20257HP2-2400 Material

D-185
TM 55-1520-210-23-3

Figure D-145. Part Number 205-031-137-1 COVER, Access Aircraft Components


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
0.032 Inch Thick

D-186
TM 55-1520-210-23-3

Figure D-146. Part Number 205-031-250-13 BASE PLATE


Fabricate from: NSN 1560-00-903-0798
Material: Fabricate From E9161-BP
A Product of Laboratory
For Electronics, Inc.,
D-187 Boston, Mass
Code Ident No. 82598
TM 55-1520-210-23-3

Figure D-147. Part Number 205-031-668-43 DOOR ASSEMBLY


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
Temp T3, 0.025 Inch Thick

D-188
TM 55-1520-210-23-3

Figure D-148. Part Number 205-031-668-53, COVER PLATE


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.025 Inch Thick

D-189
TM 55-1520-210-23-3

Figure D-149. Part Number 205-031-801-53 COVER, Tailboom


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5,
Temp T3, 0.025 Inch Thick

D-190
TM 55-1520-210-23-3

Figure D-150. Part Number 205-031-837-19, -20, -21 CLIP


Fabricate from: NSN 9535-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362,
Temp T3, 0.050 Inch Thick

D-191
TM 55-1520-210-23-3

Figure D-151. Part Number 205-031-898-1 SCREW


Fabricate from: NSN 5305-00-995-6311
Material:

Figure D-152. Part Number 204-031-136-17 COVER


Fabricate from: NSN 9535-00-167-2279
Material: AL ALY Sheet, Federal Specification QQ-A-250/5,
Temp T3, 0.032 Inch Thick

D-192
TM 55-1520-210-23-3

205-040-131-1, BRACKET, Support, Oil Line, Transmission


Figure D-153. Part Number
NSN 9535-00-232-0378
Fabricate from:
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-193
TM 55-1520-210-23-3

Figure D-154. Part Number 206-040- 162-1 BRACKET ASSEMBLY, Transmission Oil
Fabricate from: NSN 9636-00-086-9729
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-360/5,
0.032 Inch Thick
D-194
TM 55-1520-210-23-3

Figure D-155. Part Number 205-040-154-3, BRACKET, Flex Hose Support


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.0631 Inch Thick
D-195
218-261 0 - 88 -11
TM 55-1520-210-23-3

Figure D-156. Part Number 205-040-156-3 CLAMP, Hose


Fabricate from: NSN 5340-00-256-7342
Material:

D-196 Change 9
TM 55-1520-210-23-3

Figure D-157
D-197
TM 55-1520-210-23-3

Figure D-158

D-198
TM 55-1520-210-23-3

Figure D-159

D-199
TM 55-1520-210-23-3

Figure D-160. Part Number 205-040-202-1, BRACKET, Transmission Oil Filter


Fabricate from: NSN 9535-0-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

Change 8 D-200
TM 55-1520-210-23-3
Figure D-161. D-201
TM 55-1520-210-23-3
D-202 Figure D-162.
TM 55-1520-210-23-3

Figure D-163. Part Number 205-060-204-1, CHANNEL RETAINER


Fabricate from: NSN 9535-00-232-0543 Zinc Chromate Finish
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.016 Inch Thick

D-203
TM 55-1520-210-23-3
D-204 Figure D-164.
TM 55-1520-210-23-3

Figure D-165. Part Number 205-060-509-3 BRACKET, Oil Cooler Fan


Fabricate from: NSN 9535-00-232-0569 Zinc Chromate Finish
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.050 Inch Thick

D-205
TM 55-1520-210-23-3

Figure D-166. Part Number 205-060-536-1 BRACKET, Transmission Oil Cooler


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362-T3
0.025 Inch Thick

D-206
TM 55-1520-210-23-3

Figure D-167. Part Number 205-060-540-19, PAD, Oil Tank Support Assembly
Fabricate from: NSN 9390-00-263-0061
Material: Nonmetallic Channel Synthetic Rubber, Fuel and Oil Resistant, 1-1/4 In. Wide,
2.81 In. High, 60 Inch Long

Figure D-168. Part Number 205-060-770-1 SHIM, Jackshaft Support


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362-T3,
0.032 Inch Thick

D-207
TM 55-1520-210-23-3

Figure D-169. Part Number 205-060-802-11 HINGE


Fabricate from: NSN 5340-00-687-7586
Part Number 205-060-802-13 FITTING
Fabricate from: NSN 5340-00-947-9874

D-208
TM 55-1520-210-23-3

Figure D-170. Part Number 205-060-810-15


205-060-810-16 DOOR ASSEMBLY
Fabricate from: NSN 5340-00-701-9897
NSN 5340-00-993-1461
NSN 9535-00-232-0378
Material: Leaf, Butt, Hinge, Aluminum - Make from MS20257HP2-7200 Material
2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.064 Inch Thick

D-209
TM 55-1520-210-23-3

Figure D-171. Part Number 205-060-826-81, SEAL


Fabricate from: NSN 5330-00-754-7443
Material: Extrusion, Rubber, Federal Specification MlL-R-5847, Class I

D-210
TM 55-1520-210-23-3

I I I I
PART NUMBER I ITEM NAME I FABRICATE FROM NSN I A I B I L

205-060-826-83 GASKET 9320-00-241-9754 0.500 0.062 46.00

205-060-826-85 GASKET 5330-00-938-1719 0.700 0.046 47.00

205-061-520-13 PAD 5330-00-530-1858 1.250 0.120 AR

Figure D-172. Part Number 205-060-826-83 GASKET


205-060-826-85

D-211
TM 55-1520-210-23-3
D-212 Figure D-173.
TM 55-1520-210-23-3

Figure D-174. Part Number: 205-060-860-3 SUPPORT ASSEMBLY, Shown


SUPPORT, Shown, NSN 9535-00-086-9729
BRACKET, Shown, NSN 9535-00-640-2311
HINGE HALF, NSN 5340-00-838-2787
HINGE PIN, NSN 5340-00-543-3723

Part Number: 205-060-860-4 SUPPORT ASSEMBLY, Opposite


SUPPORT, Opposite, NSN 9535-00-086-9729
BRACKET, Opposite, NSN 9535-00-640-2311
HINGE HALF, NSN 5340-00-838-2787
HINGE PIN. NSN 5340-00-543-3723

Change 4 D-213
TM 55-1520-210-23-3
F i g u r e D - 1 7 5 .
D-214
TM 55-1520-210-23-3

Figure D-176. I PART NUMBER LENGTH

178036-3 AR
178038-3 AR
178040-3 AR
178042-3 AR
178044-3 AR
178050-3 AR
178050-5 AR
178050-7 AR
178052-3 AR
178052-5 AR
178052-7 AR

i ITEM NAME CHANNEL

Fabricate from: NSN 9320-00-107-4517


Material: Channel, Etrusion

D-215
TM 55-1520-210-23-3

Figure D-177. Part Numbers 205-060-908-79 & -85 FIRE WALL ASSY’S
Fabricate from: NSN 1560-00-758-0299
P/N 205-060-908-73

D-216
TM 55-1520-210-23-3

Figure D-178. Part Number: 205-060-919-3 BRACKET, Fuel System Valve


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362,
0.025 Inch Thick

D-217
TM 55-1520-210-23-3

Figure D-179. Part Number 205-061-643-1, PLATE, Baffle, Fuel Cell


Fabricate from: NSN 9535-00-167-2247
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/4, 0.250 Inch Thick

Figure D-180. Part Number 205-061 -665-1 BOLT, Eye BREAK SHARP EDGES IN MACHINES AREA
Fabricate from: NSN 5306-00-260-7578 0.10R OR CHAMFER
Material: Cadmium Plated Finish Class II Type I ALTERED FROM GOVERNMENT STANDARD
PART NUMBER AN43B-5A.

D-218
TM 55-1520-210-23-3

Figure D-181. Part Number 205-061-666-1 HOOK


Fabricate from: NSN 4030-00-852-6408
Material:

Figure D-182. Part Number 205-061-672-1 REDUCER, Fuel Pump Air Inlet
Fabricate from: NSN 4730-00-803-7981
Material:

D-219
TM 55-1520-210-23-3

Figure D-183. Part Number 205-061-677-1 WASHER, Bleed Air


Fabricate from: NSN 5310-00-187-2404
Material:

Figure D-184. Part Number 205-061-684-1, NUT


Fabricate from: NSN 5310-00-282-7835
Material:

D-220
TM 55-1520-210-23-3

Figure D-185. Part Number 205-075-142-11 TUBE, BATTERY VENT


Fabricate from: NSN 4720-00-246-4355
Material:

D-221
TM 55-1520-210-23-3

Figure D-186. Part Number 205-070-404-1, SPACER, Spot Heating Connector


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick
D-222
TM 55-1520-210-23-3

Figure D-187. Part Number 205-070-404-3, SPACER


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-223
TM 55-1520-210-23-3

Figure D-188. Part Number 205-070-416-5, 205-070-416-7 and 205-070-416-13


ORIFICE PLATE, Air Distribution Outlet
Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-224
TM 55-1520-210-23-3

Figure D-189. Part Number 205-070-430-1 and 205-070-430-3, ORIFICE,


Air Distribution Defrost Nozzle
Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-225
TM 55-1520-210-23-3

Figure D-190. Part Number 205-070-450-3 HOSE, Air Duct


Fabricate from: NSN 4720-00-736-0985
Material: Hose Air Duct, Fiberglass Cloth 2.5 Inch ID

D-226
TM 55-1520-210-23-3

Figure D-191. Part Numbers 205-070-452-1, HOSE AIR DUCT


205-070-452-3
Fabricate from: NSN 4720-00-736-0985
Material: Hose Air Duct, Fiberglass Cloth 2.5 Inch ID

D-227
TM 55-1520-210-23-3
D-228 Figure D-192.
TM 55-1520-210-23-3
Figure D-193.
D-229
TM 55-1520-210-23-3

Figure D-194. Part Number 205-070-494-1, GASKET


Fabricate from: NSN 5330-00-182-1288
Material: Cork and Rubber Sheet, Synthetic,
1/16 Inch Thick, Federal Specification
MIL-G-6183

D-230
TM 55-1520-210-23-3

Figure D-195. Part Number 205-070-609-1, SUPPORT ASSEMBLY, Blackout Curtain


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-231
TM 55-1520-210-23-3

Figure D-196. Part Number 205-070-656-1 STRAP ASSEMBLY


Fabricate from: NSN 5325-00-276-4953
NSN 5325-00-276-4946
NSN 5325-00-174-2923
NSN 5325-00-276-4969
NSN 1680-00-225-5084
NSN 8305-00-260-6910

D-232
TM 55-1520-210-23-3
D-233
TM 55-1520-210-23-3

Figure D-198. Part Number 205-031 -250-3 SUPPORT BRACKET ASSEMBLY


(Sheet 1 of 6)

D-234
TM 55-1520-210-23-3
Figure D-198. Sheet 2 of 6) D-235
TM 55-1520-210-23-3
Figure D-198.
D-236
TM55-1520-210-23-3

Figure d-198. Sheet 5 of 6)

D-237
TM 55-1520-210-23-3
D-238 Figure D-198. Sheet 5 of 6)
TM55-1520-210-23-3

Figure D. 198. (Sheet 6 of 6) D-239


TM55-1520-210-23-3

Figure D-199.

D-240
TM 55-1520-210-23-3

Figure D-200. Part Number 206-072-269-3 CLIP, Spring Tension


Fabricate from: NSN 9606-00-221-2682
Material: Wire, Steel Carbon, Spring, Federal Specification
MIL-W-6101-2, 0.67 Inch Dia

D-241
TM 55-1520-210-23-3

F i g u r e D - 2 0 1 .

D-242
TM 5 5 - 1 5 2 0 - 2 1 0 - 2 3 - 3

F i g u r e D - 2 0 2 .

D-243
TM 55-1520-210-23-3

F I G U R E D - 2 0 3 .

D-244
D-245
TM 55-1520-210-23-3
Figure B-204
TM 55-1520-210-23-3

F i g u r e D - 2 0 5 .

D-246
TM 55-1520-210-23-3
Figure D-206.
D-247
TM 55-1520-210-23-3

Figure D-207. Part Number: 205-075-134-1 TUBE, Battery Vent


Fabricate from: NSN 4710-00-278-8726
Material: 5052 AL ALY Tube, Federal Specification WW-T-700/4
Type 1, 3/8 Inch Dia, 0.049 Inch Wall Thickness

Figure D-208.

D-248 Change 9
TM 55-1520-210-23-3

Figure D-209. Part Number 205-075 -142-3 TUBE


Fabricate from: NSN 4720-00-231-2483
Material: Tubing, Rubber, Natural, Federal Specification
ZZ-T-831, Grade A, 3/8 Inch ID, 1/8 Inch Wall Thickness

D-249
TM 55-1520-210-23-3

Figure D-210. Part Number 205-075-144-3, BRACKET


Fabricate from: NSN 9535-00-167-2279
Material 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

D-250
TM 55-1520-210-23-3

Figure D-211. Part Number 205-075-229-1, MOUNTING PLATE


Fabricate from: NSN 9535-00-554-1412
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362, 0.050 Inch Thick

D-251
TM 55-1520-210-23-3

0.280
DIA 3 HOLES:
0.287
EQUALLY SPACED WITH 1
NAS1068A3 NUT PLATE 3 REQ:D
MS20426
MS20426A3 RIVIT 6 REQ’D
F3”7’‘- rFLUSH NEAR SIDE

3.80 RE F

0.84
REF
w

m
, 0.60 REF
0.191 DIA 2 HOLES
A \
0.12R TYP

0.196 NAS1068A3 NUT


PLATE 2 REQ’D
MS20426AD3R,VET,4 REQ*:D’0:4.( 8
0.191 D
0.196
0.16~+&l .75+

T2”’7r + 0.38 +0.84 TYP

I —
0.65 I I

T
0.65 RE F
+
1 1.20
1.20 NI 9 BRACKET
G&SETT

J
rO.25R
.L13 m
l= /

5.87 .- 11 r
IT

“ — 2
n, E Q S P ,11.’11

r--f
‘~1
0.25 TYP

(
I
().,

Figure D-212 part Numbers 205-076-101-1 BRACKET ASSEMBLY


205-076- 101-3
Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-252
TM 55-1520-210-23-3

Figure D-213. Part Numbers 205-076-101-1 BRACKET ASSEMBLY


205-076-101-3
Fabricate from: NSN 9539-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-253
TM 55-1520-210-23-3

Figure D-214. Part Number 205-076-102-1 BRACKET


Fabricate from: NSN 9635-00-640-2311
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-362,
0.050 Inch Thick

D-254
TM 55-1520-210-23-3

Figure D-215. Part Number 205-076-118-1 BRACKET, Angle


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-255
TM 55-1520-210-23-3

Figure D-216. Part Number 205-076-230-1 BRACKET, ANGLE


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-256
TM 55-1520-210-23-3

Figure D-217. Part Number 205-076-234-1 BRACKET, HYDRAULIC FILTER


Fabricate from: NSN 9535-00-167-2280
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.040 Inch Thick

D-257
TM 55-1520-210-23-3

Figure D-21 8. Part Number 205-706-025-11 WASHER


Fabricate from: NSN 5310-00-167-0766
Part Number 205-706-025-16 CHANNEL
Fabricate from: NSN 9535-00-232-0543
Material: Washer, Flat Steel, Cadmium Plated Make From AN970-4 Washer
2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.016 Inch Thick

Figure D-219. Part Number 11021-1 SLEEVE, Solenoid Shaft


Fabricate from: NSN 9510-00-229-4818
Material: Steel Bar, Carbon, Cold, Federal Specification QQ-S-634, Comp C1045, 0.375 Inch Dia

D-258
TM 55-1520-210-23-3

Figure D-220. Part Number 178065-1 RUNNER, Metal


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.032 Inch Thick

Figure D-221. Part Number 528307, NUT, Self-Locking


Fabricate from: NSN 5310-00-807-1475
Material:

D-259
TM 55-1520-210-23-3

Figure D-222. P a r t N u m b e r 9524491 CLIP, VALVE


Fabricate from: NSN 9535-00-554-1417
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, 0.063 Inch Thick

D-260
TM 55-1520-210-23-3

Figure D-223. Part Numbers 205-030-919-37 SHN CLIP


205-030-919-38 OPP
Fabricate from: NSN 9540-00-145-5715
Material: 2024 AL ALY Structural Angle Aluminum, Make From AND 10134-2001

D-261
TM 55-1520-210-23-3

PART NUMBER 205-060-202 LINK

FABRICATE FROM : NSN 9535-00-167-280

MATERIAL: 2024 AL ALY SHEET,


FEDERAL SPEC QQ-A-250/5 .040 INCH THICK

FIGURE D-224

D-261.1
TM 55-1520-210-23-3

Figure D-226. Part Number: Y-1159-2-3, Tape, Glass Clothr Pressure Sensitive
Fabricate from: NSN 5970-00-284-8565
Material:

D-262
TM 55-1520-210-23-3

Figure D-227. Part Number: BL8456 FMC08484 Shroud, Motor, Right Side
Fabricate from: NSN 9515-00-580-0405
Material:

D-263
TM 55-1520-210-23-3

Figure D-228. Part Number BL8453 FMC08484 Clamp, Cable


Fabricate from: NSN 9535-00-580-5516
Material: Metal Strip-Steel Corrosion, Federal Specification
MlL-S-5059, Comp 201, 0.032 Inch Thick

D-264
TM 55-1520-210-23-3

Figure D-229. Part Number BL8379 FMC08484 Bracket, Trunnion Actuator


Fabricate from: NSN 9515-00-580-5516
Material: Metal Strip-Steel Corrosion, Federal Specification
MlL-S-5059 Comp 302, 0.032 Inch Thick

D-265
TM 55-1520-210-23-3

Figure D-230. Part Number BL8515 FMC08484 Retainer, Rectifier Bracket


Fabricate from: NSN 9535-00-232-0405
Material:

D-266
TM 55-1520-210-23-3

Figure D-232.

D-267
TM 55-1520-210-23-3

Figure D-233. Part Number 120-069-1 STRIP – ANTICHAFING


Fabricate from: NSN 9330-00-143-8604
Material: Plastic Sheet 0.063 Inch Thick, 0.75 Inch Wide,
1.5 Inch Long

Figure D-234. Part Number 120-067B020 SLEEVE – Protective Coil


Fabricate from: NSN 4720-00-011-2000
Material: Nylon

D-268
TM 55-1520-210-23-3

Figure D-235; Part Number 204-011-059-1 BRACKET


Fabricate from: NSN 9536-00-086-9930
Material: 2024 AL ALY SHEET, Federal Specification QQ-A-250/4,
T3 040 Inch Thick, 2.5 Inch Wide, 4.3 Inch Long

D-269
TM 55-1520-210-23-3

Figure D-236. Part Number 204-012-022-3 RETAINER – Weight


Fabricate from: NSN 9535-00-232-0479
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/4, T3,
0.125 Inch Thick, 2.2 Inch Wide, 2.4 Inch Long

Figure D-237. Part Number 204-030-458-4 RETAINER, Window Channel Crew Door
Fabricate from: NSN 9535-00-085-4157
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250/5, T-0,
0.32 Inch Thick, 1.5 Inch Wide, 27.0 Inch Long

D-270
TM 55-1520-210-23-3

Figure D-238.
Part Number 204-030-829-16 HINGE HALF
204-030-829-27 HINGE HALF
Fabricate from: NSN 5340-00-949-8274
Material: Leaf, Butt Hinge AL ALY Anodized, 0.056 Inch Thick, 0.495 Inch Wide
Half Hinge, 1.50 Inch Total Width Make From MS20001P4-2400-Length 24.00

D-271
TM 55-1520-210-23-3

Figure D-239. Part Number 204-040-848-1 BRACKET


Fabricate from: NSN 9636-00-554-1417
Material: 2024 AL ALY SHEET, Federal Specification QQ-A-250/5 T-3,
0.063 Inch Thick, 2.6 Inches Wide, 5.0 Inches Long

D-272
TM 55-1520-210-23-3

Figure D-240. Part Number 204-060-224-9 PLATE


Fabricate from: NSN 9535-00-084-4484
Material: 2024 AL ALY SHEET, Federal Specification QQ-A-250/5, T-3,
0.020 Inch Thick, 2.1 Inches Wide, 2.1 Inches Long
TM 55-1520-210-23-3

Figure D-241. Part Number 204-030-665-11 CHANNEL


Fabricate from: NSN 9635-00-167-2174
Material: 2024 AL ALY SHEET, Federal Specification QQ-A-250/5, T-3,
0.016 Inch Thick, 4.3 Inches Wide, 31.0 Inches Long

D-274
TM 55-1520-210-23-3

Figure D-242. Part Number MS18029-1S1


MS18029-1S10
MS18029-1S14
MS18029-1S15
Terminal Board Cover
Fabricate from: NSN 5940-00-082-4642, MS18029-11S20 COVER,
NSN 5940-00-907-5939, MS18029-21NUT ASSY.

Figure D-243. Part Number 90-045-5 GUARD-SWITCH Engraved Lettering


Fabricate from: NSN 5930-00-615-6731, MS25224-1 GUARD SWITCH

D-275
TM 55-1520-210-23-3

Figure D-244. Part Number: 90-047-1 GUARD-SWITCH, Special


Fabricate from: NSN 5930-00-990-5766,
MS 25221-1 GUARD

D-278
TM 55-1520-210-23-3

Figure D-245. Part Number: 204-070-048-7 CLAMP Assembly


Fabricate from: NSN 5340-00-514-3017
NSN 5340-00-721-8182

D-277
TM 55-1520-210-23-3

NOTES:

1. PART NO. 204-070-048-15 CLAMP — MAY BE


MADE FROM ALTERED MS21919DG32
NSN 5340-00-265-6797

2. PART NO. 204-070-048-17 BRACKET MAY BE


MADE FROM ALTERED AN743-13 BRACKET
NSN 5340-00-721-8182

3. RIVET THE ALTERED AN743-13 BRACKET


TO CLAMP WITH MS20426AD4 RIVETS

Figure D-246. Part Number 204-070-048-13 CLAMP ASSEMBLY


Fabricate from: NSN 5340-00-265-6797
NSN 5340-00-721-8182

D-278
TM 55-1520-210-23-3

Figure D-247. Part Number 204-070-806 -3 STENCIL


Fabricate from: 9310-00-265-6769
Material: Stencil, Board Federal Specification U-U-625 TYPE 2, GRADE 1

D-279
TM 55-1520-210-23-3

Figure D-248. Part Number 204-070-812-1 STENCIL


Fabricate from: NSN 9310-00-265-6797
Material: Stencil Board Federal Standard UU-S-625 TYPE 2, Grade 1

Figure D-249. Part Number 204-070 -845-1 STENCIL


Fabricate from: NSN 9310-00-265-6797
Material: Stencil, Board, Federal Specifications UU-S-625, Type 2, Grade 1

D-280
TM 55-1520-210-23-3

Figure D-250. Part Number 204-070-848-3 RETAINER


Fabricate from: NSN 9535-00-232-0565
Material: 2024 AL ALY SHEET Federal Specification QQ-A-250/5, 0.032 Inch Thick,
1.0 Inch Wide, 3.5 Inches Long

D-281
TM 55-1520-210-23-3

Figure D-251. Part Number 204-072-258-1 GASKET


Fabricate from: NSN 5330-00-938-1719
Material: Asbestos

D-282
TM 55-1520-210-23-3

Figure D-252. Part Number 204-072 -258-3 GASKET


Fabricate from: NSN 5330-00-938-1719
Material: See notes

D-283
TM 55-1520-210-23-3

NOTES:
1. PURCHASE FROM JOHNS-MANVILLE PRODUCTS NEW
YORK, N.Y. CODE IDENT # 92798
2. SPECIAL ASBESTOS MATERIAL NO NSN AVAILABLE

THICKNESS SIZE STYLE

3/64 INCH 7.0 x 7.0 INCH 89

Figure D-253. Part Number 204-072-259-1 GASKET


Fabricate from: nonasbestos sheet

D-284 Change 9
TM 55-1520-210-23-3

Figure D-254. Part Number 204-076-264-1 BUS BAR


Fabricate from: NSN 6150-00-225-0267
Material: Copper Sheet, Federal Specifications QQ-C-576, ANNEALED
0.063 Inch Thick, 2.0 Inches Wide, 5.8 Inches Long

D-285
TM 55-1520-210-23-3

Figure D-255. Part Number 204-076-264-3 BUS BAR


Fabricate from: NSN 6150-00-226-0267
Material: Copper Sheet, Federal Specifications QQ-C-576, ANNEALED
0.063 Inch Thick, 2.0 Inches Wide, 6.0 Inches Long

D-286
TM 55-1520-210-23-3

Figure D-256. Part Number: 204-075-264-5 BUS BAR


Fabricate from: NSN 6150-00-225-0267
Material: Copper Sheet, Federal Specification QQ-C-576, Annealed,
0.063 Inch Thick, 2.0 Inches Wide, 4.3 Inches Long

D-287
TM 55-1520-210-23-3

Figure D-257. Part Number 204-075-264-9 BUS BAR


Fabricate from: NSN 6150-00-225-0267
Material: Copper Sheet, Federal Specification QQ-C-567, Annealed,
0.063 Inch Thick, 2.0 Inches Wide, 2.6 Inches Long

D-288
TM 55-1520-210-23-3

Figure D-258. Part Number 204-075-230-3 BUS BAR


Fabricate from: NSN 6150-00-225-0267
Material: Copper Sheet, Federal Specification QQ-C-576, Annealed,
0.063 Inch Thick, 2.7 Inch Wide, 5.0 Inch Long

D-289
TM 55-1520-210-23-3

Figure D-259. Part Number 204-075 -230-5 BUS BAR


Fabricate from: NSN 6150-00-225-0267
Material: Copper Sheet, Federal Specification QQ-C-576, Annealed,
0.063 Inch Thick, 2.7 Inches Wide, 4.1 Inches Long

D-290
TM 55-1520-210-23-3

Figure D-260. Part Number 204-075-152-3 SHUNT Assembly


Fabricate from: NSN 6625-00-166-1005, MS91587-4 SHUNT
Material: MS91587-4 SHUNT, By Installing Above
Bolts in Place of Furnished Bolts

D-291
TM 55-1520-210-23-3

Figure D-261. Plate, Doubler, Rear PN 5065697


Fabricate from: NSN 9535-00-232-1882
Material: AL Alloy, 6061-T6, .062 THK, QQ-Q-250/11

D-292
TM 55-1520-210-23-3

Figure D-262. Part Number 206-030-137-4 GUSSET


Fabricate from: NSN 9635-00-232-0489
Material: 2024 AL ALY Federal Specification QQ-A-362,
Temp 0 T42, to 0.032 Inch Thick, 5.5 Inches Wale,
6.0 Inches Long

D-293
TM 55-1520-210-23-3

NOTES:
1. 205-030-148-5 COVER MAKE FROM .2024 AL ALY FEDERAL SPECIFICATION
QQ-A-250/5 T3 0.040 INCH THICK, 5.0 INCHES LONG, 5.0 INCHES WIDE
2. 205-030-148-7 SPACER MAKE FROM 2024 AL ALY FEDERAL SPECIFICATION
QQ-A-250/5 T3 0.125 INCH THICK, 1.0 INCH WIDE, 1.72 INCHES LONG
3. 205-030-148-9 PLATE MAKE FROM 2024 AL ALY FEDERAL SPECIFICATION
QQ-A-250/5 T3 0.040 INCH THICK, 1.0 INCH WIDE, 2.1 INCH LONG

Figure D-263. Part Number 205-030-148-3 COVER Assy of


Fabricate from, NSN 9535-00-167-2280
NSN 9535-00-232-0418
Material: 2024 AL ALY Federal Specification QQ-A-250/5 T3 0.040 Inch Thick
2024 AL ALY Federal Specification QQ-A-250/5 T3 0.125 Inch Thick

D-294
TM 55-1520-210-23-3

Figure D-264. Part Number 205-030-164-215 RADIAL BLOCK


Fabricate from: NSN 9535-00-086-4516
Material: 7075 AL ALY Federal Specification QQ-A-250/3 T6 0.190
Inch Thick, 0.8 Inch Wide, 0.8 Inch Long

D-295
TM 55-1520-210-23-3

Figure D-265. Part Number 205-030-239-3 BEAM


Fabricate from: NSN 9635-00-232-0646
Material: 2024 AL ALY Federal Specification QQ-A-362, T3,-
0.020 Inch Thick, 3.6 Inch Wide, 12.8 Inch Long

D-296
TM 55-1520-210-23-3

Figure D-266. Part Number 206-030-239-5 BEAM


fabricate from: NSN 9535-00-232-0546
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, T-3
0.020 Inch Thick, 3.6 Inch Wide, 11.06 Inch Long

D-297
TM 555-1520-210-23-3

Figure D-267. Part Number 205-030-257-15 DOUBLER


Fabricate from: NSN 9535-00-086-9860
Material: 7075 AL ALY Sheet Federal Specification QQ-A-250/13 T-6
0.032 Inch Thick, 5.8 Inch Wide, 23.3 Inch Long

D-298
TM 55-1520-210-23-3

1. 206-031-423-31 & -32 CLlP


MAKE FROM AND 10134-1406 STRUCTURAL
ANGLE ALUMINUM EXTRUSION 1.1 INCHES LONG
2. 205-031-423-33 & -34 CLIP
MAKE FROM AND 10134-1406 STRUCTURAL
ANGLE ALUMINUM EXTRUSION 1.5 INCHES LONG

3. DRILL HOLES TO MATCH TO INSTALL

Figure D-268. Part Number 206-031-423-31 CLIP


206-031-423-32 CLIP
206-031-423-33 CLIP
206-031-423-34 CLIP
Fabricate from: NSN 9640-00-596-3006
Material: 7076 Structural Angle Alum ALY
Extruded 90 Deg. Federal Specification
QQ-A-200-11 T6, 1.250 Inch H of 1 Leg.
1.60 Inch H of Other Leg, 0.094 Inch Thick

D-299
TM 55-1520-210-23-3

NOTES:
1. 205-031-481-17 PLATE MAKE FROM
METAL STRIP STEEL 0.125 1.NCH THICK
2. RIVET NUTPLATE TO 205-031-481-17
PLATE

Figure D-269. 206-031-481-15 PLATE, Assy of


NSN 9515-00-204-0220
Metal Strip, Steel Annealed
Federal Specification MlL-S-18729 Comp 4130, Cond N
0.125 Inch Thick, 1.2 Inch Wide, 2.3 Inch Long

D-300
TM 55-1520-210-23-3

Figure D-270. Part Number 205-031-481-23 BUMPER


205-031-481-29 BUMPER
Fabricate from: NSN 9320-00-202-1846
Material; Rubber Sheet Synthetic
Federal Specification MIL-R-8855, Class 3,
Grade 60, 0.0625 Inch Thick, 0.75 Inch Wide

D-301
TM 55-1520-210-23-3

Figure D-271

D - 3 0 2
TM 55-1520-210-23-3

Figure D-272. Part Number 205-031-862-17S HINGE HALF


205-03-862-21S
Fabricate from: NSN 5340-00-993-1461
Material: Leaf Butt Hinge AL ALY Anodized,
0.040 Inch Thick, 0.531 Inch Wide, 72.00 Inches Long

D-303
TM 55-1520-210-23-3

NOTES:
1, 205-031-862-19 HlNGE HALF
MAKE FROM MS20257YP2-385Q
BUTT HllUGE MATERIAIL
2. CUT HINGE MATERIAL T(3 PROPER
LENGTH 38.60 INCH LONG

Figure D-273. Part Number 205-031-862-19 HINGE HALF


Fabricate from: NSN 5340-00-993-1461
Material: Hinge, Butt, Alum Aly Anodized
0.040 Inch Thick, 0.531 Inch Wide

D-304
TM 55-1520-210-23-3

Figure D-274. Part Number 205-031-862-47S STRIP


Fabricate from: No national stock number
Material: Plastic sheet, 0.063 Inch Thick,
1.25 Inch Wide, 2.0 Inches Long

D-305
TM 55-1520-210-23-3

Figure D-275. Part Number 205-060-110-1 FILLER, Laminated


Fabricate From: NSN 9535-00-702-7786
Material : Shim Stock, Laminated Aluminum Federal
Specification AMS 4013, 0.125 Inch Thick, 1.5 Inch Wide,
11.2 Inch Long

D - 3 0 6
TM 55-1520-210-23-3
D-307
TM 55-1520-210-23-3

Figure D-277. Part Number 205-062-696-1 PLATE


Fabricate from: NSN 9635-00-232-0478
Material: 2024 AL ALY Federal Specification QQ-A-250/5 T3,
0.125 Inch Thick, 1.7 Inch Wide. 1.7 Inch Long

D-308
TM 55-1520-210-23-3

Figure D-278. Part Number 206-072-221-3 LANYARD


Fabricate from: NSN 4010-00-075-7941
Material:

D-309
TM 55-1520-210-23-3

Figure D-279. Part Number 205-070-772-1 STRAP, Assembly


Fabricate from: NSN 8305-00-267-3009
Material: Nylon Webbing Type XVIl, MIL-W-4088

D-310
TM 55-1520-210-23-3

Figure D-280. Part Number 205-070-795-1 COVER


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY, Federal Specification QQ-A-362 T3,
0.063 Inch Thick, 3.5 Inch Wide, 11.70 Inch Long

D-311
TM 55-1520-210-23-3
Figure D-281.
D-312
TM 55-1520-210-23-3

Figure D-282. Part Number 205-070-882-1 STENCIL


Fabricate from: NSN 9310-00-265-6797
Material: Stencil Board, Federal Specification UU-S-625,
Type 2 Grade 1

D-313
TM 55-1520-210-23-3

Figure D-283. Part Number 205-072-039-1 DOOR, Assy Of


Fabricate from: NSN 9330-00-291-4800,
NSN 5340-00-993-1461
Material: Plastic sheet Acrylic Transparent, Federal Specification
MIL-P-5425 FINA, 0.187 Inch Thick, 4.2 Inch Wide, 14.4 Inch Long
Leaf, Butt Hinge A1 A AL ALY 0.0531 Inch Wide Make From
MS20257HP2-130 (Length 13.0)

D-314
TM 55-1520-210-23-3

Figure D-284. Part Number 206-072-224-1 GUIDE TUBE


Fabricate from: NSN 9535-00-232-1882, 5310-00-728-7716
Material: 6061 AL ALY Federal Specification QQ-A-205/11 TO,
0.063 Inch Thick, 1.3 Inch Wide, 7.5 Inch Long

D-315
TM 55-1520-210-23-3

Figure D-285. Part Number 205-072-225-1 GUIDE-TUBE


Fabricate from: NSN 9635-00-232-1882, 5310-00-772-3720
Material: 6061 AL ALY, Federal Specification QQ-A-205/11, TO
0.063 Inch Thick, 1.3 Inch Wide, 6.7 Inch Long

D-316
TM 55-1520-210-23-3

Figure D-286. Part Number 205-072-226-1 CLAMP-GUIDE


Fabricate from: NSN 9535-00-232-1882
Material: 6061 AL ALY Federal Specification QQ-A-250/11 TO,
0.063 Inch Thick 1.0 Inch Wide, 3.0 Inch Long

D-317
TM 55-1520-210-23-3

Figure D-287. Part Number 206-072-227-1 SUPPORT BRACKET ASSEMBLY OF


Fabricate from: NSN 9635-00-167-2267, 5310-00-728-7716
Material: 2024 AL ALY, Federal Specification QQ-A-250/6 TO,
0.040 Inch Thick, 2.0 Inch Wide, 7.0 Inch Long

D-318
TM 55-1520-210-23-3

Figure D-288. Part Number 205-072-227-3 SUPPORT BRACKET, Assembly of


Fabricate from: NSN 9635-00-167-2267, 5310-00-728-7716
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, TO,
0.032 Inch Thick, 3.0 Inch Wide, 3.0 Inch Long

D-319
TM 55-1520-210-23-3

Figure D-289. Part Number: 205-072-317-1 BRACKET


Fabricate from: NSN 9535-00-232-0378
Material: 2024 AL ALY Federal Specification QQ-A-250/5 T3,
0.063 Inch Thick, 1.5 Inch Wide, 2.38 Inch Long

D-320
TM 55-1520-210-23-3

Figure D-290. Part Number 206-706-029-11 SEAL


Fabricate from: NSN 9390-00-134-0184
Material: Rubber Synthetic Extruded Federal Specification
MIL-R-6855 Class II Grade 60, Color BLACK

D-321
TM 55-1520-210-23-3

Figure D-291. Part Number: 205-706-029-15 LINK


Fabricated from: NSN 9535-00-084-4551
Material: 2024 AL ALY Federal Specification QQ-A-250/5 T-3
0.040 Inch Thick, 1.0 Inch Wide, 5.0 Inch Long

D-322
TM 55-1520-210-23-3

Figure D-292. Part Number 205-075-135-19 TUBE


Fabricate from: NSN 4720-00-540-3644
Material: Rubber Black Synthetic
Federal Specification MIL-R-6855

Figure D-293. Part Number 205-075-142-5 TUBE


Fabricate from: NSN 4720-00-540-3644
Material: Tubing Rubber Synthetic Black Federal Specification
MIL-R-6855 Class 2 Grade 40, 1/8 Inch Wall Thick,
3/8 Inch ID

D-323
TM 55-1520-210-23-3

Figure D-294. Part Number: 205-75-142-9 TUBE


Fabricate from: NSN 4720-00-540-3644
Material: Tubing Rubber Synthetic Black
Federal Specification MlL-R-6855 Class 2
Grade 40, 1/8 Inch Wall Thick, 3/8 Inch I.D.

D-324
TM 55-1520-210-23-3

Figure D-295 Part Number 205-075-151-1 BRACKET


Fabricate from: NSN 9535-00-232-0583
Material: 2024 AL ALY Sheet, Federal Specification QQ-A-250 T3,
0.040 Inch Thick, 2.2 Inch Wide, 3.0 Inch Long

D-325
TM 55-1520-210-23-3

Figure D-296. Part Number 205-075-210-3 PLATE


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Federal Specification QQ-A-250/5,
0.032 Inch Thick, 2.5 Inch Wide, 2.5 Inch Long

Figure D-297. Part Number 205-075-210-5 PLATE


Fabricate from: NSN 9535-00-167-2279
Material: 2024 AL ALY Federal Specification QQ-A-250/5,
0.032 Inch Thick, 1.0 Inch Wide, 1.0 Inch Long

D-236
TM 55-1520-210-23-3

Figure D-298. Part Number: 205-075-237-5 PLATE RECEPTACLE


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, 0.032 Inch
Thick, 2.7 Inch Wide, 4.0 Inch Long

D-327
TM 55-1520-210-23-3

NOTES
1 RIVET 205-961-102-23 RETAINER TO 205-961-102-17 COVER

Figure D-299. Part Number 205-961-102-17 COVER


Fabricate from: NSN 9535-00-086-9729, NSN 9515-00-683-9294
Material: 2024 AL ALY, Federal Specification QQ-A-250/5 T3,
0.032 Inch Thick, 3.3 Inch Wide, 6.6 Inch Long. Metal Sheet
Steal Corrosion, Federal Specification, MIL-S-5059 Comp 302,
Craw 18-18, 0.060 Inch Thick, 3.6 Inch Wide, 4.6 Inch Long

D-328
TM 55-1520-210-23-3

Figure D-300. Part Number 205-961-102-25 COVER


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY, Federal Specification QQ-A-250/5 T3
0.032 Inch Thick, 3.3 Inch Wide, 6.6 Inch Long

D-329
TM 55-1520-210-23-3

Figure D-301. Part Number 205-961-102-33 COVER


Fabricate from:
Material: Metal Sheet Steel Corrosion, Federal Specification
MIL-S-5059 COMP 302, Annealed, CRES 18-8, 0.060
Inch Thick, 6.7 Inch Wide, 9.8 Inch Long, 3.16 Inch Wide,
4.6 Inch Long

D-330
TM 55-1520-210-23-3

Figure D-302. Part Number 205-961-155-3 WINDOW


Fabricate from: :NSN
Material: Polycarbonate Resin Material Federal
Specification L-P-393 and Bell Helicopter
SPEC 299-947-044, 0.064 Inch Thick,
4.0 Inch Wide, 4.0 Inch Long

D-331
TM 55-1520-210-23-3

Figure D-303. Part Number MS25083-2BB5 JUMPER ASSY


MS25083-2BB6 JUMPER ASSY
Fabricate from: NSN 5940-00-143-4794
NSN 6145-00-819-0058
Material: Terminal Lug Copper (MS25036-112)
Wire, Electrical Copper Tinned, Federal
Specification QQ-W-343-TYPE RB Class 1, AWG 12

D-332
TM 55-1520-210-23-3

Figure D-304. Part Number 204-060-816-33 GASKET


Fabricate from: NSN 5330-00-938-1719
Material:

D-333
TM 55-1520-210-23-3
D-334
TM 55-1520-210-23-3

Figure D-306. Part Number: 205-030-007-347 DOOR


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY, Federal Specification QQ-A-250/5 T13,
0.032 Inch Thick, 5.5 Inch Wide, 6.8 Inch Long

D-335
TM 55-1520-210-23-3

Figure D-307. Part Number: 205-030-163-25 ATTACHMENT


Fabricate from: NSN 9535-00-086-9860
Material: 7075 AL ALY, Federal Specification QQ-A-250/l 3 TO,
0.032 Inch Thick, 2.5 Inch Wide, 13.2 Inch Long

D-336
TM 55-1520-210-23-3

Figure D-308. Part Number: 205-030-163-125 ATTACHMENT


Fabricate from: NSN 9535-00-086-9860
Material: 2024 AL ALY, Federal Specification QQ-A-250/5 T3,
0.040 Inch Thick, 3.2 Inch Wide, 8.3 Inch Long

D-337
TM 55-1520-210-23-3

Figure D-309. Part Number: 205-030-163-129 ATTACHMENT


Fabricate from: NSN 9535-00-084-4551
Material: 2024 AL ALY Federal Specification QQ-A-250/5 T3,
0.040 Inch Thick, 2.2 Inch Wide, 4.2 Inch Long

D-338
TM 55-1520-210-23-3

Figure D-310. Part Number: 205-030-163-231 RADIUS BLOCK


Fabricate from: 9535-00-084-4516
Material: 2024 AL ALY, Federal Specification QQ-A-250/5 T3,
0.188 Inch Thick, 1.5 Inch Wide, 1.5 Inch Long

D-339
TM 55-1520-210-23-3

Figure D-311. Part Number 205-030-163-329 STIFFENER


Fabricate from: NSN 9535-00-086-9456
Material: 7075 AL ALY, Federal Specification QQ-A-250/13 TEMPO To T6
0.050 Inch Thick, 2.5 Inch Wide, 11.2 Inch Long

D-340
TM 55-1520-210-23-3
Figure D-312
D-341
TM 55-1520-210-23-3

Figure D-313. Part Number 205-030-385-18 GUIDE


Fabricate from: NSN 8305-01-031-0130
Material: Weather Strip; Cloth Fabric 0.063 Inch Thick,
1.25 Inch Wide, 92.5 Inch Long

D-342
TM 55-1520-210-23-3

Figure D-314. Part Number 205-030-385-21 DOUBLER


Fabricate from: NSN 9515-00-234-7953
Material: Metal Steel Corrosion Resistant 18-8 Rolled,
Annealed Federal Specification MIL-S-5059 Comp 301,
0.063 Inch Thick, 1.8 Inch Wide, 2.0 Inch Long

D-343
TM 55-1520-210-23-3

Figure D-315. Part Number: 205-030-407-121 ANGLE


Fabricate from: 9635-00-167-2278
Material: 2024 AL ALY Federal Specification QQ-A-250/5,T3,
0.025 Inch Thick, 1.2 Inch Wide, 11.0 Inch Long

D-344
TM 55-1520-210-23-3

Figure D-316. Part Number 205-030-407-317 SEAL


Fabricate from: NSN 5340-00-949-8281
Material: Extruded Silicone Rubber, Bell Specification 299-947-095,
Color Black or Grey

D-345
TM 55-1520-210-23-3

Figure D-317. Part Number 205-030-539-7 DOOR


Fabricate from: NSN 9535-00-167-2278
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, T3,
0.025 Inch Thick, 4.0 Inch Wide, 4.5 Inch Long

D - 3 4 6
TM 55-1520-210-23-3

Figure D-318. Part Number 205-030-611-15 TUBE


Fabricate from: NSN 4720-00-235-5455
Material: Hose, Rubber Synthetic, Federal Specification MIL-R-6855,
Class V 1/4 ID, 1/16 Wall Thk. 15.0 Inch Long

D-347
TM 55-1520-210-23-3

NOTES:

1. PART NO. 205-030-615-93 AND -94


MAKE FROM BELL STD 110-015-1
MATERIAL BOTH ITEMS 98.00 INCH LONG.
2. PURCHASE FROM BELL HELICOPTER OR
BURKE RUBBER CO. 2250 SOUTH TENTH,
SAN JOSE, CALIFORNIA

Figure D-319. Part Number 205-030-615-93-SEAL


205-030-615-94-SEAL
Fabricate from: 9390-00-877-6254
Material: Extrusion-Rubber, Door Seal Bell Specification
299-947-095 Color Black or Grey

D-348
TM 55-1520-210-23-3

Figure D-320. Part Number 206-031-669-137 DOUBLER


Fabricate f rem: NSN 9536-00-664-1417
Material: 2024 AL ALY Federal Specification QQ-A-250/5, T3,
0.063 Inch Thick, 2.0 Inch Wide, 3.4 Inch Long

D-349
TM 55-1520-210-23-3

Figure D-321. Part Number: 205-030-711-27 CAP STRIP


205-030-711-28 CAP STRIP
Fabricate from: NSN 9536-00-232-7636
Material: 7075 AL ALY Federal Specification QQ-A-250/l3, T6,
0.020 Inch Thick, 3.2 Inch Wide, 16.8 Inch Long.

D-350
TM 55-1620-210-23-3

Figure D-322 Put Number 206-030-729-49 SUPPORT COVER


Fabricate from: NSN 9535-00
Material 2024 AL ALY, Federal Specification QQ-A-250/5. T3.
0.026 inch Thick 1.7 inch Wide, 20.4 Inch Long

NOTES:
1. PART NO. 206-030-819-21 MAKE FROM
ANTI-CHAFFING TAPE #366. 0.80 INCH
WIDE, 40.0 INCH LONG PURCHASE FROM
MINNESOTA MINING AND MFG COMP
ST PAUL MINN. CODE IDENT 76381
2. ALTERNATE MATERIAL FOR ANTl-
CHAFFING TAPE #649-3% MILLS
PURCHASE FROM MINNESOTA MINING
AND MFG. COMP, ST PAUL, MINN.
CODE IDENT 76381

Figure D-323. Part Number 205-030-819-21 STRIP-CHAFFING


Fabricate from:
Material TAPE, ANTI-CHAFFING #366, 0.80 Inch Wide,
40.0 Inch Long

D-351
TM 55-1520-210-23-3

PART NO.

Figure D-324. Part Number: 295-030-846-33S HINGE


Fabricate from: NSN 5340-00-949-8274
Material: HINGE, BUTT AL ALY Anodized 0.056 Inch Thick,
0.495 Inch Wide, 72.00 Inch Long

NOTES:

1. PART NO. 205-030-850-21 HINGE


HALF MAKE FROM MS20257HP2-7200
STOCK
2. CUT HINGE MATERIAL TO THE
REQUIRED LENGTH 24.00 INCH LONG

Figure D-325. Part Number: 205-030-850-21 Hinge Half


Fabricate from: NSN 5340-00-993-1461
Material: Leaf, Butt Hinge - Aluminum Alloy Anodized,
0.040 Inch Thick, 0.531 Inch Wide, 72.00 Inch Long

D-352
TM 55-1520-210-23-3

NOTES:
1. PART NO. 205-060-826-79 GRIP
MAKE FROM SCOTCH-TRED COLOR
GREY PURCHASE FROM MINNESOTA
MINING AND MFG. CO. ST. PAUL,
MINN. (CODE IDENT NO 76381)
2. ATTACH GRIP MATERIAL TO COWL
ASSY. HAND HOLD.

Figure D-326. Part Number 205-060-826-79 GRIP


Fabricate from: NSN 7220-00-206-0390
Material: Cloth Material, Adhesive Backing One Side,
Abrasive Material Other Side, Scotch Tred Color Grey

D-353
218-261 0 - 88 -16
TM 55-1520-210-23-3

NOTES

1. 206-060-909-7 SEAL MARK FROM


3/8 DIA BULB, TADPOLE SEAL, FIREWALL
1.2 INCH WIDE, 87.0 INCH LONG
2. PURCHASE SEAL FROM JOHNS-MANSVILLE
COMP, NEW YORK N.Y. CODE IDENT 92788

Figure D-327. Part Number 206-060-909-7 SEAL


Fabricate from: NSN 9390-00-861-9178
Material: SEAL, Bulb 3/8 Inch Dia, Firewall Seal

D-354
TM 55-1520-210-23-3

Figure D-328. Part Number 205-060-909-17 GASKET


Fabricate from: NSN 5330-00-938-1719
Material: GASKET, Asbestos Material 0.047 Inch Thick, 1.9 Inch Wide,
87.0 Inch Long

D-356
TM 55-1520-210-23-3

Figure D-329. Part Number: 205-061-232-1 SEAL


Fabricate from: NSN 9320-00-466-1884
Material: Closed Cell Medium Sponge Federal Specification AMS-3195,
0.187 Inch Thick, 3.2 Inch Wide, 13.0 Inch Long

D-356
TM 55-1520-210-23-3

Figure D-330. Part Number: 205-061 -234-1 SEAL FORWARD


Fabricate from: NSN 9320-00-456-1804
Material: Closed Cell Medium Sponge, Federal Specification AMS-3195,
0.187 Inch Thick, 3.0 Inch Wide, 13.5 Inch Long

D-357
TM 55-1520-210-23-3
Figure D-331. Part Number 205-061-412-1 Bracket
Fabricate From: NSN 9535-00-554-1417
Material: 2024 AL ALY, Federal Specification QQ-A 250 5 T3,
0.063 Inch Thick. 2.2 Inch Wide, 4.0 Inch Long
D-358
TM 55-1520-210-23-3

Figure D-332. Part Number 205-061-521-1 RADIUS BLOCK


Fabricate from: NSN 9636-00-232-0418
Material: 2024 AL ALY Federal Specification QQ-A-200/3, T4, or T3510 or
T3511, 0.125 Inch Thick, 0.875 Inch Wide

D-359
TM 55-1520-210-23-3

Figure D-333. Part Number: 205-061-643-3 PLATE


Fabricate from: NSN 9535-00-232-0398
Material: 2024 AL ALY, Federal Specification
QQ-A-250/5 T3, 0.080 Inch Thick,
3.1 Inch Wide, 4.9 Inch Long

0-360
TM 55-1520-210-23-3

Figure D-334. (Sheet 1 of 3) Part Number: 205-070-054-1 COVER ASSY


Fabricate from: NSN 9535-00-232-0378
NSN 9515-00-184-8822
Material: 2024 AL ALY, Federal Specification QQA-250/5,
T3, 0.063 Inch Thick. Steel Corrosion Resistant
18-8, Federal Specification MIL-S-5059 Comp 301,
1/2 Hard, 0.025 Inch Thick

D-361
TM 55-1520-210-23-3

Figure D-334. (Sheet 2 of 3)

D-362
TM 55-1520-210-23-3

Figure D-334. (Sheet 3 of 3)

Figure D-335. (Sheet 1 of 7) Part Number: 205-072-038-1 INSTRUMENT PANEL ASSY

Fabricate from: See Part Number Sheets


Material: See Part Number Sheets

D-363
TM 55-1520-210-23-3

Figure D-335. (Sheet 2 of 7) Part Number: 205-072-038-3 SIDE


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY Federal Specification QQ-A-250/4 T3
0.032 Inch Thick, 9.7 Inch Wide, 14.3 Inch Long

D-364
TM 55-1520-210-23-3

Figure D-335. (Sheet 3 of 7) Part Number 206-072-038-5 END


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY Federal Specification QQ-A-250/4 T3,
0.032 Inch Thick, 6.1 Inch Wide, 8.2 Inch Long

D-365
TM 55-1520-210-23-3

Figure D-335. (Sheet 4 of 7) Part Number: 205-072-038-7 END


Fabricate from: NSN 9535-00-086-9729
Material: 2024 AL ALY, Federal Specification QQ-A-250/4 13,
0.032 Inch Thick, 6.1 Inch Wide, 10.0 Inch Long

D-366
TM 55-1520-210-23-3

Figure D-335. (Sheet 5 of 7) Part Number: 205-072-038-9 PANEL


Fabricate from: NSN 9535-00-086-9930
Material: 2024 AL ALY Federal Specification QQ-A-250/4 T3,
0.040 Inch Thick, 7.0 Inch Wide, 16.0 Inch Long

D-367
TM 55-1520-210-23-3

Figure D-335. (Sheet 6 of 7) Part Number 206-072 -038-9 PANEL

D-368
TM 55-1520-210-23-3

Part Number 205-072-038-13 HINGE PIN


Fabricate from: NSN 5340-00-182-9901
Material: Rod Straight, Headless, Corrosion Resistant
Cadmium Plated 0.062 Dia., 11.88 Inch Long

Figure D-335. (Sheet 7 of 7) Part Number 206-072-038-11 HINGE HALF


Fabricate from: NSN 5340-00-993-1461
Material: Leaf Butt Hinge AL ALY Anodized 0.531 Inch Wide,
0.040 Inch Thick, 12.00 Inch Long

D-369
TM 55-1520-210-23-3

Figure D-336. Part Number: 205-075-137-3 RELAY


Fabricate from: NSN 5306-00-819-5120
NSN 5945-00-660-931 5
Material: Machine Bolt (NAS 467-6-32)
Relay Solenoid (MS 24171-D1)

D-370
TM 55-1520-210-23-3

205-706-025-17 ADAPTER SEGMENT


Figure D-337. Part Number:
Fabricate from: NSN 9535-00--232-0405
Material: 2024 AL ALY, Federal Specification, QQ-A-362, T3,0.093
Inch Thick, 13.7 Inch Wide, 14.0 Inch Long

D-371
TM 55-1520-210-23-3

Figure D-338. Part Number 205-706-025-19 ADAPTER SEGMENT


Fabricate from: NSN 9535-00-232-0405
Material: 2024 AL ALY Federal Specification QQ-A-362 T3,
0.093 Inch Thick, 27.5 Inch Wide, 27.5 Inch Long

D-372
TM 55-1520-210-23-3

Figure D-339. Part Number 67SPL12757-0114 WRENCH ADAPTER


Fabricate from: NSN 1615-00-474-9840
Material:

Change 5 D-373
TM 55-1520-210-23-3

Figure D-340. Part Number 397-1 COVER ELECTRICAL TERMINAL BOARD


Fabricate from: NSN 5940-00-082-4642
Material: Plastic, phenol-formaldehyde

D-374
TM 55-1520-210-23-3

Figure D-341. Part Number: 204-030-853-97 CHANNEL


204-030-853-98 CHANNEL
204-030-853-99 CHANNEL
204-030-853-100 CHANNEL
Fabricate from: NSN 1560-00-004-4458
Material: Channel Rigid Pile Lining Uncovered, 33/64 Inch Wide,
1/2 Inch High 3/16 to 1/4 Opening

D-375
TM 55-1520-210-23-3

Part Number AN8 18-4D, Nut, Tube Coupling


NSN 4730-00-287-0289
Part Number MS208 19–4D, Sleeve, Flares, Tube
NSN 4730-00-302-8641 Figure D-342.

D-376
TM 55-1520-210-23-3

Figure D-343, Plate , Modification

D-377
TM 55-1520-210-23-3

Figure D-344. Washer, Safety

D-378
TM 55-1520-210-23-3

Figure D-345. Gasket

Figure D-346. Gasket

Change 4 0-379
TM 55-1520-210-23-3

Figure D-347. Seal, Tadpole

Figure D-348. Gasket

D-380
TM 55-1520-210-23-3

Figure D-349. Engine torque transmitter nut


PART NUMBER 270-580292-12
FABRICATE FROM: NSN 5310001991028
MATERIAL: AN924-12D

D-381
TM 55-1520-210-23-3

NOTE: Overall length of cable assy


to be determined at time of installation.

Figure D-350. Part Number 1560-UH1-76C Cable Assembly, Cargo Door


Fabricate from: NSN 4010-00-222-4482 Cable 1/16inch
NSN 9505-00–528–5017, Rod 3/16 inch
4181 steel
NSN4030-00-452-2568 Swaging sleeve (2)
TM 55-1520-210-23-3

Figure D-351 Part Number AA 8621-2D12 Gasket


Fabricate from: NSN 9320-00-839-8503
Material: Rubber Sheet Cellular,
MIL-R-6130, Type 2, Grade A,
condition soft

D-383
TM 55-1520-210-23-3

PART NUMBER NOMENCLATURE FABRICATE FROM NSN A

204-030-287-89 SILICONE RUBBER 9320-00-827-0584 26 INCHES


STRIP

204-030-287-91 SILICONE RUBBER 9320-00-827-0584 2.5 INCHES


STRIP

204-031-347-25 SILICONE RUBBER 9320-00-827-0584 24 INCHES


STRIP

205-031-669-105 RUBBER SEAL 9320-00-113-5845 100 INCHES

205-060-805-13 RUBBER SEAL 9390-00-138-4145 17 INCHES

205-030-028-29 SILICONE RUBBER 9320-00-827-0584 32.5 INCHES


STRIP

205-030-484-25 SILICONE RUBBER 9320-00-827-0584 32.5 INCHES


STRIP

Figure D-352,

D-384
TM 55-1520-210-23-3

Figure D-353.(Sheet 1 of 2)

D-385

218-261 0 - 88 -17
TM 55-1520-210-23-3

NOTES

1 PIN A, E, F, G, J, K, L, M, S NOT USED


2 MARK "AUX JACK”
3 UNINSULATED LEAD MUST BE COVERED BY
SLEEVING, SECURE JACK TO CABLE
4 INSULATED WITH STD PHONE TIP
(0.080 DIA X 0.5 INCH TEST PROD)
5 INSULATED, CABLE MOUNT ACCEPTS STD
PHONE TIP (NOTE 4)

Figure D-353 Part Number 1560 UH1-772-1, RPM


WARNING DETECTOR TEST EXTENDER CABLE
ASSEMBLY (sheet 2 of 2)
Fabricate from: NSN 6145-00-851-8505
Material: MIL-W-50861 Type 2
NSN 5970-00-557-6254
Material: MIL-J-7444, Type 1 Class 1
NSN 5935-00-078-3586
Material: MIL-C-26482
NSN 5935-00-765-5989
Material: MIL-C-26482
NSN 5935-00-909-7894
Material: 5
NSN 5905-00-141-0591
Material: MIL-R-39008
NSN 5940-01-007-7875
Material: MIL-T-7928

Part Number 1560UH1-772-2, RPM


WARNING DETECTOR TEST JUMPER ASSEMBLY
Fabricate from: NSN 6145-00-851-8505
Material: MIL-W-5086 Type 2
NSN 5935-00-578-3494
Material:

D-386
TM 55-1520-210-23-3

Figure D-354. Part Number 1560-UH1-983-3,


Angle, Air Distribution Valve

Fabricate from: NSN 9535-00-086-9729


Material: 2024-T3 QQ-A-250/5
.032 X 1.75 X 5.25
D-387
TM 55-1520-210-23-3

Figure D-355. Part Number 1560-UH1-781 Doubler Plate,


R-1963/ARN
Fabricate from: NSN 9535-00-232-8846
Material: Aluminum Sheet, .032 inch
thick 2024-T3, QQ-A-250/4

D-388
TM 55-1520-210-23-3

Figure D-356. Part Number 1560-UH1-791. Cross


Brace Extension, R-1963/ARN
Fabricate f r o m : NSN 9535-00-232-8825
M a t e r i a l : Aluminum Sheet, .063 inch
thick 2-24-T3, QQ-A-350/4

D-389
TM 55-1520-210-23-3

1. DEBURR SARP EDGES

2. FABRICATE FROM NSN 5310-00-282-6904, WASHER FLAT

Figure D-357. Part Number 1560-UH-1-990-1 washer, Flat

D-390 Change 8
TM 55-1520-210-23-3

Figure D-358, Part Number: 204-030-853-93, WIPER


Fabricate from: NSN 6320-00-079-0897
Material: YM3 Strip, Commercial
A Product of FSCM 82654.
Alternate, #T179Y 5022 Poly-Pile,
A product of FSCM 77824.

D-391
TM 55-1520-210-23-3

Figure D-359. Port Number 1560-UH-1-761 , Security Device, Window

D-392
TM 55-1520-210-23-3

Figure 360. Part Number 1560-UH-1-762-1, Rod, Security Device Pilot's Door.

D-393
TM 55-1520-210-23-3

Figure D-361. Part Number 1560-UH-1-764, Security Device

D-394
TM 55-1520-210-23-3

Figure D-362. Part Number 1 560-UH-1-765, Plate Copilot Security Device

D-395
TM 55-1520-210-23-3

PART NUMBER: 1560UH1-1 WASHER, ANTI-CHAFFING

FABRICATE FROM: NSN 5970-00-118-8838

MATERIAL: INSULATION SHEET, ELECTRICAL FIBERGLASS

FIGURE D-363.

D-396
TM 55-1520-210-23-3

0.031

Figure D-364. Part Number: 5310-UH1-036-1, WASHER


Fabricate from: NSN 9380-00-143-7110
Material: Rubber Sheet

Figure D-364.1. Part Numbers 8531804 AND 8531834, GASKET


Fabricate from: NSN 9320-00-814-4583; P/N 8635958-7
Material: Rubber, Sheet, Cellular

Change 9 D-397
TM 55-1520-210-23-3

P/N 205-030-009-51
Fabricate from 98 inches of NSN 9320-01-012-7683

FIGURE D-365, EXTRUSION-RUBBER

D-398
TM 55-1520-210-23-3

Part Number: 205-071-118-101


Figure D-366.
205-071-118-103
205-071-118-105
205-071-118-107
Fabricated from: 9310-00-265-6797
Material: Stencil Board, Federal Specification
UU-S-625, Type 2, Grade 1

D-399
TM 55-1520-210-23-3

Figure D-367. Plate


Doubler Assembly, PN1560-UH-1-1044
Fabricate From: NSN 9535-00-086-9930 Metal Sheet
5310-00-781-9493 Nut
5320-00-117-6938 Rivet
Material: Aluminum Alloy,. 040 Thick, 2024-T3 per QQ-A-250/4

D-400
TM 55-1520-210-23-3
Figure D-368.
D-401
TM 55-1520-210-23-3

PART NUMBER: 205-031-669-101


FABRICATE FROM: NSN B305-00-205-2735
MATERIAL: SEAL, STANFLEX FAB

FIGURE D-369.

D-402
TM 55-1520-210-23-3

FIGURE D-370.

D-403
TM 55-1520-210-23-3

FIGURE D-371.

D-404
TM 55-1520-210-23-3

Figure D-372. Master Caution Panel, PN ES-C-221355

Fabricate from: NSN 1680-00-02I-5510, PANEL


P/N 25-0259-30, LENS
P/N 25-0259-220, LENS

D-405
TM 55-1520-210-23-3

Figure D-373. DELETED

D-406 Change 5
TM 55-1520-210-23-3

Figure D-374. Bracket, Relay PN ES-C-221697


Fabricate From: NSN 9535-00-084-4395

D-407
TM 55-1520-210-23-3

Figure D-375. Jumper Assy, Bus Bar, PN ES-B-221720

Fabricate From: NSN 5970-00-815-1295, 6150-00-225-0267


Material: Copper Sheet, .063 Thk, annealed per spec. QQ-C-576

D-408
TM 55-1520-210-23-3

Figure D-376. Plate, Reinforcing, DF Ant., Forward PN5065695

Fabricate From: NSN 9535-00-085-4133


Material: Al. Alloy, 6061-T6, .032 Thk, QQ-A-250/11

D-409
TM 55-1520-210-23-3

Figure D-377. Pedestal, Access Door, PN ES-F-221565

Fabricate From: NSN 1560-00-885-1835

D-410
TM 55-1520-210-23-3
Figure D-378. Blanket Assembly, PN ES-F-221752
D-411
TM 55-1520-210-23-3

Figure D-379. Bracket Angle PN ES-C-221739

Fabricate From: NSN 9535-00-232-0405


Material: Aluminum Alloy, 0.063 Thick, 2024-T3 per spec. QQ-A-250/5

D-412
TM 55-1520-210-23-3

Figure D-380. Support, Connector, PN ES-C-221709

Fabricate From: NSN 9535-00-167-2248


Material: .031 Thick Aluminum Alloy, 2024 Temper
T4 per spec. QQ-A-250/4
D-413
TM 55-1520-210-23-3

Figure D-381. Panel, Control PN ES-C-221569

Fabricate From: NSN 6110-01-063-3689

D-414
TM 55-1520-210-23-3

Figure D-382. Plate, Mounting PN ES-C-221440


Fabricate From: NSN 9535-00-085-4134, NSN 5340-00-815-4930
Material: Aluminum Alloy, .250 Thick, 2024-T3 per spec QQ-A-250/4

D-415
TM 55-1520-210-23-3

Figure D-383. Plate, Structural Aircraft, PN ESC-213928


Fabricate From: NSN 9535-00-085-4169
Material: Alum. Alloy, Sheet, 6061-T6, per QQ-A-250/11
D-416
TM 55-1520-210-23-3

Figure D-384. Plate, Structural Aircraft PN ES-B-221712


Fabricate From: NSN 9535-00-084-4413
Material: Aluminum Alloy, 6061-T6 per QQ-A-250/1 1

D-417

218-261 0 - 38 -18
TM 55-1520-210-23-3
Figure D-385. Spacer, Plate PN ES-B-221566
Fabricate From: 9535-00-232-1882
Material: Aluminum Alloy, 6061-T6, Sheet, per QQ-A-250/l1
D-418
TM 55-1520-210-23-3
Figure D-386. Knob Assy, indicator PN ES-B-221427
Fabricate From: 1560-00-771-2502
D-419
TM 55-1520-210-23-3

Figure D-387. Bracket, Angle PN ES-B-220355


Fabricate From: 9535-00-232-0378
Material: .063 Aluminum Alloy, 2024-T3 per QQ-A-250/5

D-420
TM 55-1520-210-23-3

Figure D-388. Plate, Structural, Aircraft PN ES-B-220354


Fabricate From: NSN 9535-00-232-0565
Material: .03 ZX2X2 AL Aly 2024-T3 per QQ-A-250/5

D-421
TM 55-1520-210-23-3
Figure D-389 (sheet 1 of 2). B. I.T.E. Ant. Mtg. PN ES-D-221672
Material: Aluminum Aly., Sheet, .050 thick, 2024-T3, QQ-A-250/4
D-422
TM 55-1520-210-23-3

Figure D-389 (sheet 2 of 2). B. I. T. E., Ant., Mtg. PN ES-D-221672


D-423
TM 55-1520-210-23-3

Figure D-390. Bracket, Angle PN ES-B-220311


Fabricate From: NSN 9535-00-232-0378
Material: .063 AL. Alloy 2024-T3 per QQ-A-250/5

D-424
TM 55-1520-210-23-3

Figure D-391. Cable Assy, Special Purpose, Electrical PN ES-B-220309


Fabricate From: NSN 6145-00-236-9503 and 5940-00-143-4794
Material: Wire, Tinned, Soft, Type RB Class M and Terminal, Lug, Crimp
Style

D-425
TM 55-1520-210-23-3

Figure D-392. Plate, Reinforcing, DF Ant., Rear PN 5065698


Fabricate From: NSN 9535-00-232-1882
Material: AL. Aloy, 6061-T6, .032 THK, QQ-A-250/11

D-426
TM 55-1520-210-23-3

Figure D-393 Plate, Doubler, Forward PN 5065696


Fabricate from: NSN 9535-00-084-4448
Material: AL Alloy, 6061-T6, .062 THK, QQ-Q-250/11

D-427
TM 55-1520-210-23-3

FIGURE D-394 MAIN ROTOR BLADE TIE DOWN AFTER HUB SPRING INCORPORATION

*U. S. Government Printing Office; 1988 -65 4-047/81059

D-428 Change 1
TM 55-1520-210-23-3

Figure D-395 Gasket GRHB-1.

Figure D-396 Gasket GRHB-2.

Change 3 D-429
TM 55-1520-210-23-3

Figure D-397. Part Number 205-060-805-35 RETAINER 2 ea 62”


205-060-805-37 RETAINER 2 ea 17”
Fabricate from: NSN 9535-00-167-2267
Material: 2024 AL ALY, Federal Specification QQ-A-250/5, T3,
0.032 inch DIA.

Figure D-398. Part Number 204-050-228-1 CLAMP ASSEMBLY, Support


Fabricate from: NSN 1560-00-691-0553

D-430 Change 4
TM 55-1520-210-23-3

Figure D-399. Part Number 205-060-254-9 SEAL HINGE


Fabricate from: NSN 9330-00-939-7534
Material: STRIP PLASTIC, 0.250 X 0.750 x19.00

Figure D-400. Part Number 205-060-805-41 SEAL BULB


Fabricate from: NSN 9390-00-851-9178
Material: MIL SPEC: RL-2066

Change 4 D-431
TM 55-1520-210-23-3

Figure D-401. Part Number: DK-1 , ANTI-CHAFFING PAD


Fabricate from: NSN 5970-00-912-1907
Material: MELAMIDE RESIN IMPREGNATED GLASS CLOTH
MIL-P-15037 .031 Thick

Figure D-402. Part Number 1560-UH1-981 SHIM


Fabricate from: NSN 9535-00-084-4450
Material: 2024T3 AL ALY

D-432 Change 4
TM 55-1520-210-23-3

Figure D-403. Part Number 204-031-766-1 DOOR STAY


Fabricate from: NSN 9330-01-295-4343
Material: TETRALON, 510, P/N 5T125X12.000E

Change 5 D-433
TM 55-1520-210-23-3

Figure D-404. Part Number: 205-030-872-21


Fabricate from: NSN 9320-00-814-4583
Material: MIL-R-6130 Extrusion Rubber,
Solid Rectangular, Color Natural
26.2 Inches long

Figure D-405 Part Number 205-030-872-23


Fabricate from: NSN 9320-00-814-4583
Material: MIL-R-6130 Extrusion Rubber,
Solid Rectangular, Color: Natural
82.7 inches long

D-434 Change 4
TM 55-1520-210-23-3

Figure D-406. Part Number 205-031-481-33, DOUBLER -.100 X 1.2 x 1.0


Fabricate from: 9535-00-064-4430
Material: 2024 AL ALY SHEET, Federal Specification, QQ-A-250/5,
T3 .100 inch Thickness

Change 4 D-435
TM 55-1520-210-23-3

Figure D-407. cover Assembly P/N 1730-EG-1 79 (Sheet 1 of 2)

D-436 Change 4
TM 55-1520-210-23-3

Figure D-407. Cover Assembly P/hi 1730-EG-1 79 (Sheet 2 of 2)


Change 4 D-437
TM 55-1520-210-23-3

Figure D-408

D-438 Change 4
TM 55-1520-210-23-3

Figure D409

Change 4 D-439
TM 55-1520-210-23-3

Figure D-410, Bracket 106324

Change 4 D-440
TM 55-1520-210-23-3

Figure D-411

Change 5 D-441
TM 55-1520-210-23-3

Figure D-412. Part Number: 205-030-919-33


Fabricate from: NSN 9535-00-232-0378
METAL SHEET, QQA 250-5
GRZ404, T3
0.063 INCH THICK

D-442 Change 4
TM 55-1520-210-23-3

Fig. D-413 Gasket: PIN AA9500-2317-0


Manufactured from: 5330-01-330-2786
Dimensions. .50 ± .03 inch thick
.75 ± .03 Inch wide
Lenghts Item 1-35 5/8 inches
2-5 3/4 inches
3-11 3/4 inches
4 -12 1/2 inches
5 -14 3/8 inches
6-4 inches

Change 5 D-443
TM 55-1520-210-23-3

Figure D-414. Replacement of lift link bushings

D-444 Change 5
TM 55-1520-210-23-3

Fig. D-415. DOOR ROLLER, P/N SKRV2-1994

FABRICATE FROM: NSN 9390-01-020-9953


MATERIAL Nylon
BEARING: PIN MS14102-4
LOCK RING: P/N MS16625-1062

Change 8 D445(D.446 Blank)


TM 55-1520-210-23-3

APPENDIX E

STORAGE OF AIRCRAFT

SECTION 1. GENERAL INFORMATION

E-1 . PURPOSE. d. Storage of Aircraft Undergoing Maintenance (no time


limit). This category of maintenance will include general
NOTE requirements of storage of aircraft undergoing any main-
tenance action which causes the aircraft to be inactive for
more than seven days. Due to the wide range of main-
Aircraft that are inactive for seven or more con-
tenance actions that may create this situation, some storage
secutive days must be placed in storage.
procedures will not be required and a degree of latitude is
Scheduling helicopters for flight or ground run
given to the local maintenance officer on the storage
a minimum of once every seven days is key to
measures needed for the particular situation. The seven day
long term preservation of mission ready
limit is a guideline and variances are allowed at the discre-
aircraft. If this is not possible the aircraft should
tion of the maintenance officer.
be processed into the appropriate catagory of
storage.
E-2. STORAGE RESPONSIBILITY.
The purpose of this chapter is to assure the readiness of
inactive aircraft (not flown or ground run for seven or more The local maintenance officer shall be responsible for
consecutive days) by processing for storage. The objective processing the helicopter ‘for storage taking into considera-
is to minimize airframe and component corrosion, seal and tion the anticipated duration of storage and local climatic
packing deterioration and maintain avionics and electrical conditions.
equipment in an operable condition. Procedures provided
are for aircraft in storage for six months or less, inspection a. Records. The processing organization shall be respon-
requirements during storage and procedures to activate the sible for performing a receiving check of the helicopter and
aircraft after storage. for the records-keeping requirements during storage. For
forms used for equipment inventory refer to DA PAM 738-
a. Flyable Storage (no time limit). This implies main- 751 Army Maintenance Management System.
taining the helicopter in operable condition and will entail
mooring helicopter, installing protective covers, and a daily b. Removed Equipment. Equipment and components
inspection every seven day, and an engine runup every removed from the helicopter as part of storage procedures
fourteen days. shall be stored and records maintained in accordance with
current supply directives.
b. Short Term Storage (1-45 days). This type storage in-
cludes a ground runup, preservation of the engine fuel sys- NOTE
tem, oil system, and exposed helicopter components
together with removal of classified communications equip- Any component removed because of accident
ment battery, clock fire extinguishers, and first aid kit. The or materiel failure shall not be preserved but
helicopter will be moored, protective covers will be in- shall be shipped in the present condition.
stalled, and a daily inspection will be performed every
seven days.
c. Classified Equipment. Removal of classified equip-
ment other than communications equipment shall be discre-
c. Intermediate Storage (46-180 days). This category of tionary with the Commanding Officer. His decision will be
storage will include all requirements of Short Term Storage. based on consideration of local storage facilities, climatic
In addition, the fuel system will be preserved and a cor- conditions affecting deterioration or corrosion, and man-
rosion control program established. hours required to remove and reinstall such equipment. Ap-
propriate security measures shall be taken for all classified
equipment either removed or left installed.

Change 3 E-1
TM 55-1520-210-23-3

E-3. INSPECTION OF STORED HELICOPTERS. inspected for condition of protective coverings whenever
they have experienced high winds (exceeding 40 mph). In
Aviation unit maintenance officer shall be responsible for addition, the following general inspection procedures apply
establishing an inspection program to ensure that the to all types of storage:
helicopter remains properly preserved. Helicopters in Fly-
able Storage will have a daily inspection at least once every a. Provide adequate helicopter ventilation and preserva-
seven days and an engine runup at least once every 14 days. tion. Determine cockpit temperatures by thermometer, and
Helicopters in Short Term or Intermediate Storage shall be when in excess of 135°F (57°C), ventilate to prevent con-
inspected for corrosion every 15 days where relative densation and mildew.
humidity exceeds 40%. Helicopters in any storage shall be

E-2 Change 3
TM 55-1520-210-23-3

b. Check that all fuselage, wings, center section, e. Inspect static ground wires, tie-down straps
control surfaces, and empennage drain holes are and mooring devices (rope, cables, rods, or eyes) at
open. regular intervals but immediately after being
subjected to winds exceeding 40 mph. Replace
c. If covers are used, check that they are not deformed or deteriorated ground wires or mooring
accumulating water. provide drains if necessary. devices and tiedown straps.
Replace damaged or deteriorated covers.
f. Inspect communications equipment for
d. Regularly inspect and treat for corrosion as fungus and corrosion. At the first indication of
necessary. Inspection frequency will be determined deterioration, remove, clean, preserve, and package
by local humidity conditions. Close attention should any affected components to comply with MIL-P-116.
be given to areas where moisture does not evaporate Stow these items in the helicopter from which
readily. Evidence of corrosion will not be as obvious removed.
on painted surfaces as it is on bare metal; however,
corrosion can attack metal through paint and will be g. Enter inspection date in the helicopter Log
indicated by blisters or scaly appearance of paint. Book.

SECTION II. FLYABLE STORAGE

E-4. INSPECTION PRIOR TO FLYABLE (1) Use every precaution to keep the engine
STORAGE. and accessories clean. Keep the air intake duct,
plenum chamber, and compressor inlet screens clean
Helicopters in this storage category shall be and free of any foreign materials. Use solvent (C261)
maintained in a serviceable condition. Perform Daily to clean external surfaces.
Inspection (PMD cards) prior to accomplishing the
requirements of subsequent paragraphs. Enter the (2) Start engine in accordance with the
date and type storage in the helicopter log book. Operator’s Manual.

NOTE NOTE
The general requirements in Section I are This runup may be omitted if the
applicable. helicopter has been operated within the
past fourteen days and is know to be
dry.
E-5. PRESERVATION. (3) Limit the run to that necessary to stabilize
engine temperatures.
a. Power-train.
(1) Check the power-train lubrication system (4) Shutdown engine in accordance with the
including sight gages. Service the system in Operator’s Manual.
accordance with Chapter 1.
(S) After engine cools, install engine inlet and
(2) The preservation run up prescribed in exhaust protective covers. If these are not available,
paragraph E-5b completes the preservation of seal the openings with barrier material (C115) and
transmission and gearboxes. secure with tape (C279).
b. Engine. (6) Cover additional engine cowling open-
ings as in step (5) above.

Cleaning materials l e flammable and


toxic. Avoid akin contact l nd breathing (7) Record in the helicopter log book the date
of solvent vapors. helicopter was placed in Flyable Storage.

E-2.1/(E2.2 blank)
TM 55-1520-210-23-3

b. Hydraulic System. Check the hydraulic reser- E-6. MAINTENANCE OF PRESERVATION DURING
voir and fill as necessary with hydraulic fluid (C131). FLYABLE STORAGE.
a. Helicopter shall be inspected in accordance
c. Fuel System. Service fuel tanks to normal ca- with local directives and requirements in preceding para-
pacity after each engine runup. Drain water from fuel graph E-3.
tanks before adding fuel.
b. A preventive daily inspection in accordance
NOTE with PMD cards will be performed at least every seven
days, together with an engine runup in accordance with
Full tanks minimize fuel contamination by
paragraph E-5b will be performed at least every fourteen
condensation. The maintenance officer
days.
shall determine the interval of periodic
drainage. E-7. DEPRESERVATION AFTER FLYABLE STOR-
AGE.
d. Battery.
a. Remove protective covers, clean, and return to
(1) Check that all cockpit switches are OFF. storage.

(2) Clean the battery as necessary, but leave WARNING


it in the helicopter unless the temperature is expected to
be colder than -40 degrees F (-40 degrees C).
Cleaning materials are flammable and
(3) Service the battery in accordance with TM toxic. Avoid skin contact and breathing of
11-6140-203-14-2. solvent vapors.
b. Remove all barrier material and tape. Remove
e. Airframe. tape residue with solvent, (C261).
(1) Install pitot tube cover or wrap pitot tube c. Clean helicopter as necessary in accordance
with barrier material (C115) and secure with tape (C279). with Chapter 1.
d. Open all doors and windows for ventilation.
(2) Disengage circuit breakers.
e. Remove all tiedowns.
(3) Close all doors and windows. f. If preventive maintenance daily inspections
has not been performed within the last 7 days perform
(4) Install static ground wire. PMD inspection in accordance with PMD cards.
g. Remove and stow static ground wire.
(5) Install helicopter shipping and storage cov-
er (flyable configuration), if available, in accordance with h. Indicate on helicopter maintenance records
instructions accompanying covers. that it has been depreserved and removed from storage.

SECTION II. SHORT TERM STORAGE


E-8. INSPECTION PRIOR TO STORAGE. a. Ensure that all removed components are pre-
served and stowed within the helicopter in suitable con-
NOTE tainers.

The general requirements of Section I are b. Record all removed or disconnected parts in
a part of these procedures. the helicopter maintenance records.

Change 9 E-3
TM 55-1520-210-23-3

WARNING (4) Deleted.

Cleaning materials are flammable and (5) Deleted. I


toxic. Avoid skin contact and breathing
of solvent vapors. (6) If engine is inoperable, preserve power-
train as follows:
c. Bolts, washers, nuts, and other hardware
which are removed during disassembly should be
(a) Remove main rotor blades in accord-
coated with a light coat of corrosion preventive
ance with Chapter 5.
compound (C86), and reinstalled as removed from the
major component unless otherwise specified.
(b) Remove mast assembly in accordance
with Chapter 6.
d. Check fuel, oil, and hydraulic lines/hoses for
leakage.
(c) Spray inside of transmission through
e. Lubricate the helicopter for the 50 hour interval top opening with one gallon of oil (C166 or C168).
in accordance with Chapter 1. While spraying, manually rotate internal gears and
bearings with input drive quills.
f. Record the date and type of storage in the
helicopter records. (d) Reinstall mast assembly in accordance
with Chapter 6.
E-9. PRESERVATION.

a. Power-train.
Cleaning materials are flammable and
toxic. Avoid skin contact and breathing
of solvent vapors.
Cleaning materials are flammable and
toxic. Avoid skin contact and breathing (e) Apply fingerprint remover (C88) to all
of solvent vapors. unpainted surfaces of mast assembly. Remove
residue with solvent (C261 ) on a clean cloth.
(1) Clean the exposed bare metal surfaces
with a clean cloth dampened with solvent (C261 ) and (f) Apply corrosion preventive compound
coat with corrosion preventive compound (C86). (C86) to all unpainted surfaces.

(2) Deleted. (g) Reinstall main rotor in accordance with


Chapter 5.
(3) Check power-train lubrication levels
including sight gages and service in accordance with (h) Ensure 42 and 90 degree gear-
Chapter 1. boxes have been filled with oper-

E-4 Change 6
TM 55-1520-210-23-3

sting oil (C166 or C168) to the proper b. Engine. (Operable).


operating level.

(7) Cover breather holes in


gearboxes and transmission with barrier Cleaning materials are flammable
material (C115) and secure with tape and toxic. Avoid skin contact
(C279). and breathing of solvent vapors.

E-4.1/(E-4.2 blank)
TM 55-1520-210-23-3

(1) Use every precaution to keep engine and (9) When engine has cooled sufficiently to
its accessories clean. Keep air intake screens, plenum prevent auto-ignition, set throttle to IDLE position.
chambers, and compressor inlet screens clean and
free of foreign material. Use solvent (C261 ) for general CAUTION
cleanup.
Do not operate starter beyond operat-
ing limits, three runs of 40 seconds
each during any 60 minute period. A
Cleaning materials are flammable and cooling interval of three minutes is re-
toxic. Avoid skin contact and breathing quired between each 40-second run. Do
of solvent vapors. not engage starter until engine has
stopped rotating. START FUEL switch,
if installed, shall be ON. Ignition switch
(2) Check oil level; service as required in shall be ON.
accordance with Chapter 1. Remove any spilled oil on
painted surfaces with a clean cloth dampened with (10) Motor engine with starter to pump lubricat-
solvent (C261 ). ing oil into fuel system.

CAUTION (11) Open and close throttle to ensure flushing


the fuel control.
To prevent accidental firing of the
engine ensure IGNITION SYSTEM (12) Continue motoring engine until fuel-free
IGNITER SOLENOID circuit breaker is oil flows into container.
open. (Pulled out.)
(13) Disconnect lubricating oil source from fuel
system.
(3) Disengage ignition system igniter sole-
noid circuit breaker. (14) Connect main and starting fuel hoses.

WARNING (15) Spray power turbine rotor with sufficient


corrosion preventive compound to cover blades.
Cleaning materials are flammable and
toxic. Avoid skin contact and breathing (16) Turn ignition switch OFF.
of solvent vapors.
NOTE
(4) Remove fuel inlet and pump discharge Use dehydrated air for spraying opera-
strainers from fuel control. Clean with solvent (C261 ) tions.
and reinstall. Replace servo supply filter.
(17) Install engine inlet and exhaust covers. If
(5) Disconnect main fuel hose from main fuel not available, seal openings with barrier material
manifold and starting fuel hose from starting fuel sole- (C115) and secure with tape (C279).
noid valve on T53-L-11 series engines.
(18) Remove, disassemble, and clean oil filter.
Immerse filters in operating lubricant (C192),
(6) Disconnect main fuel hose from flow- assemble, and install.
divider assembly and starting fuel hose from starting
fuel solenoid valve on T53-L-13 engines. (19) Attach tag to fuel control stating, ENGINE
PRESERVED; FUEL CONTROL PRESERVED WITH
MIL-L-6081 OIL. FLUSH WITH OPERATING FUEL
(7) Install temporary lines on ends of hoses to
BEFORE PLACING IN SERVICE.
allow drainage into a suitable container.
(20) Visually check entire engine to ensure:
(8) Connect hose from source of oil (C192) to
fuel control inlet fitting. (a) All holes are plugged.

E-5
TM 55-1520-210-23-3

(b) All ports are capped. (6) Connect fuel hoses and replace drain
plug.
(c) All external parts are complete and
secure. (7) Safety throttle to CLOSED position.

(8) Pour oil (C192) into openings made


(d) All bare metal, including internal and
accessible by removal of overspeed governor until the
external threads, is covered with corrosion-preventive
fuel regulator is filled.
compound (C86).

(9) Pour oil (C192) into overspeed governor


(21) Deleted. while rotating driveshaft by hand.

(22) Record date and extent of engine pres- (10) Pour excess lubricating oil from over-
ervation in helicopter records. speed governor and install.

c. Engine (Inoperable). (11) Install engine inlet and exhaust covers, or


if not available, seal openings with greaseproof barrier
material (C115) and secure with tape (C279).
WARNING

Cleaning materials are flammable and (12) Seal the gap between the bleed band and
toxic. Avoid skin contact and breathing compressor housing by encircling the engine with a
of solvent vapors. narrow strip of barrier material (C115) and secure with
tape (C279).

(13) Visually check entire engine to ensure:


NOTE

Engine involved in an accident shall not (a) All holes are plugged.
be preserved. Refer to TM 55-2840-
229-23. (b) All ports are capped.

(1) Use every precaution to keep engine and (c) All external parts are complete and
its accessories clean. Keep air intake screens, plenum secure.
chambers, and compressor inlet screens clean and
free of foreign material. Use solvent (C261 ) for general (d) All bare metal including internal and
cleaning. external threads is covered with corrosion preventive
compound (C86).
CAUTION
(14) Attach a tag to controls stating, FUEL
To prevent accidental firing of the CONTROL HAS BEEN PRESERVED WITH MIL-L-
engine, ensure IGNITION SYSTEM 6081 OIL. FLUSH WITH STANDARD FUEL BEFORE
IGNITER SOLENOID circuit breaker is PLACING IN SERVICE.
open. (Pulled out.)
(15) Record date and extent of engine pres-
(2) Disengage ignition system igniter sole- ervation in helicopter records.
noid circuit breaker.
d. Rotors and Controls.
(3) Disconnect the fuel lines from the fuel
control inlet and outlet ports. (1) Lubricate rotor system in accordance with
lubrication order, Chapter 1.

(4) Remove fuel control drain plug and drain


fuel from the fuel control and hoses.
Cleaning materials are flammable and
(5) Remove overspeed governor and drain toxic. Avoid skin contact and breathing
fuel. of solvent vapors.

E-6 Change 6
TM 55-1520-210-23-3

(2) Apply fingerprint remover (C88) to all f. Hydraulic System.


unpainted metal surfaces. Remove residue with
solvent (C261) and a clean cloth. (1) Fill hydraulic reservoir with fluid (C131).
(2) Wipe exposed portions of hydraulic
boost cylinder actuator pistons with lint-free cloth
moistened with hydraulic preservative fluid
(C 132).
Cleaning materials are flammable and
toxic. Avoid skin contact and breathing g. Avionics.
of solvent Vapors.
(1) Remove, attach condition tags, and turn-in
(3) Wipe all parts dry with a clean lint-free all headsets and microphones to Supply.
cloth and apply corrosion preventive compound
(C86) on all unpainted surfaces not in contact (2) Leave all unclassified installed avionic
with bearings. equipment in helicopter.

(4) Clean surface of rotor blades with h. Fuel System. Maintain fuel tanks FULL for
cleaning compound (C67). Wipe blades comp- the duration of the storage period to preclude
letely dry with clean lint free cloth. condensation. Drain water from tanks before adding
fuel. If a requirement exists to drain tanks, refer to
(5) D e l e t e Intermediate Storage.

i. Battery

(1) Remove battery and turn in to the battery


shop.
Cleaning materials are flammable and
(2) Clean battery compartment, quick
toxic. Avoid skin contact and breathing
disconnect plug, cables, battery shelf, and vent
of solvent vapors. hoses with a solution of five ounces boric acid
crystals dissolved in one gallon of water. Rinse with
(6) Apply a light coat of corrosion-preven- clean water and allow to dry.
tive compound (C88) to tail rotor cables, sprocket
and chain. Cycle controls through full range for (3) Seal the battery vent tubes and cover
complete coverage. the quick-disconnect plug with barrier material
(C115) secured with tape (C279).
e. Landing Gear.
j. Airframe.
(1) Place blocks or shoring under skid tubes to
provide free air passage. (1) Park and moor helicopter with main and
tail rotor tiedowns installed in accordance with
(2) Clean skid/crosstubes and treat for Chapter 1.
corrosion in accordance with TM 55-1500-204-
25/1 . (2) Remove clock, fire extinguishers, and first
aid kits. Tag for condition and transfer to Supply to
prevent possible pilferage.

(3) Apply pitot cover or cover pitot head


and static ports with barrier material (C115) se-
Cleaning materials are flammable and cured with tape (C279).
toxic. Avoid skin contact and breathing
of solvent vapors. (4) Remove windshield wipers and blades.
(3) Repaint any exposed metal surfaces. If Wrap, tag, and store in the cockpit.
paint cannot be touched up, coat bare metal
surfaces with corrosion preventive compound (5) Close all doors, windows, inspection
(C88). panels, and cowling.

Change 4 E-7
TM 55-1520-210-23-3

(3) Remove, clean, and store windshield


(6) C l e a n a l l e x p o s e d a n t e n n a s a n d cover and barrier material/tape covering open-
connections. ings of voids. Remove tape residue with solvent
(C261).
(7) Close all openings or voids not already
covered with barrier material (C98) secured with tape (4) Open all doors and windows to ventilate
(C221). helicopter.

(8) Cover windshield with cover. (5) Install windshield wipers and blades.

(9) Install static ground wire. (6) Remove pitot cover and ensure static ports
are open and free of tape residue.
(10) Install storage covers, if available, in
accordance with instructions accompanying covers. (7) Replace clock, fire extinguisher, and first
aid kit.
(11) Annotate helicopter records to reflect
short term storage. (8) Remove main/tail rotor tiedown and any
mooring devices.

E-10. MAINTENANCE O F b. Battery.


PRESERVATION DURING SHORTTERM
STORAGE. (1) Remove barrier material/tape from vent
tubes and quick-disconnect plug in battery
compartment,
a. Inspect helicopters in accordance with local
directives and those requirements outlined in (2) Install battery, and after ensuring that all
paragraph E-3. switches are off, attach quick-disconnect plug.

b. Should conditions change so that the


helicopter is to remain in storage for a longer period of c. Fuel System (tanks and lines).
time than 45 days, represerve it in accordance with
Section IV. (1) Drain water from tanks.

NOTE (2) Inspect fittings and clamps.

Do not renew Short Term Storage. (3) Sample fuel and test for contamination.

d. Avionics.
E-11. DE PRESERVATION AFTER
(1) Replace headsets and microphones.
SHORT TERM STORAGE.
(2) Ensure that all components including
a. Airframe. antennae are in place.

(1) Remove storage covers, clean, and return e. Hydraulic System.


to supply.
(1) Check reservoir level and inspect system
(2) Remove static ground wire. for leaks.

Cleaning materials are flammable and Cleaning materials are flammable and
toxic. Avoid skin contact and breathing toxic. Avoid skin contact and breathing
of solvent vapors. of solvent vapors.

E-8
TM 55-1520-210-23-3

(2) Clean exposed portion of (3) Check and clean transmission


hydraulic boost cylinder actuator oil filters.
pistons with a clean cloth dampened with
solvent (C261). i. Engine
f. Landing Gear. Remove blocks or (1) Remove covers of inlet, exhaust,
shoring under skid tubes. and bleed band if applicable. Perform
engine wash, paragraph 4-4b.
g. Rotors and Controls

Cleanlng materials are flammable


Cleaning materials are flammable and toxic. Avoid skin contact
and toxic. Avoid skin contact and breathing of solvent vapors.
and breathing of solvent vapors.
(2) Inspect opening for foreign
(1) Clean main and tail rotor material and corrosion. Wipe clean with
assemblies with solvent (C261). Wipe solvent (C261).
dry with lint-free cloth.
(3) Remove chip detector from
(2) Ensure that corrosion preven- accessory drive gearbox and drain plugs
tive compound is removed from tail rotor from fuel control. After oil has
control chain and sprocket. drained, clean and replace chip detector
(if serviceable) and plugs.
(3) Lubricate in accordance with
Chapter 1. (4) Ensure ignition system igniter
solenoid circuit breaker is not engaged.
(4) Ensure stabilizer bar dampers
have fluid (C129) to the proper level. (5) Disconnect main fuel hose from
Check timing after refilling and replace main fuel manifold or flow divider, as
damper if unsatisfactory. (See Chapter applicable, and drain into a container
5). of at least two gallons capacity.

h. Power-train. (6) Check oil level; service if


necessary.

Cleaning materials are flarmnable Do not exceed starter limita-


and toxic. Avoid skin contact tions.
and breathing of solvent vapors.
(7) Operate helicopter boost pump
(1) Using solvent (C261), clean to prime fuel system, then motor engine
all surfaces coated with corrosion with starter.
preventive compound. Wipe dry with a
clean cloth. (8) Move throttle to maximum open
until a solid stream of fuel with no air
(2) Check sight gages for proper bubbles is observed flowing into the
lubricant levels. Service as necessary container At least one gallon of
in accordance with Chapter 1. fuel must flow into the container.
Change 4 E-9
TM 55-1520-210-23-3

applicable, and inspect engine for


NOTE leakage.

Engine lubrication system is (10) Engage ignition system


fully primed when oil pressure igniter solenoid circuit breaker.
gage shows a s t e a d y p o s i t i v e
indication. (11) Operate the engine for
approximately ten minutes at a minimum
(9) Connect main fuel hose to main N2 rpm of 5500. Restrict the engine
fuel manifold or flow divider, as operation at IDLE position to a

E-10
TM 55-1520-210-23-3

maximum of two minutes in each period. Check NOTE


all instruments for normal operation and ensure
that the engine temperature has stabilized. If there are fewer than ten hours
(Refer to Operator’s Manual.) operating time on engine since new or
last overhaul, repeat steps (11 ) through
(12) Shut down engine, (15) until no contamination is evident or
analysis o f t h e c o n t a m i n a t i o n
(13) Remove oil filter, check for excessive determines that the engine must be
condensation, clean and install. replaced.

(14) Remove chip detector, check for


excessive contamination, clean and install. j. Miscellaneous.

(1) Clean helicopter as necessary in


accordance with Chapter 1

Cleaning materials are flammable and


(2) Check helicopter records for components
toxic. Avoid skin contact and breathing
which had been removed or disconnected. Ensure
of solvent vapors,
that all have been replaced and connected.
(15) Remove fuel inlet strainer and pump
discharge strainer from fuel control. Check for (3) Ensure that all related systems have been
contamination, clean with solvent(C261) and install. properly depreserved and serviced before any system
Replace servo supply filter. or component operational check is performed.

(16) If no contamination is evident, engine is


(4) Check that all procedures required to
ready for ground test. If there is slight contamination,
activate the helicopter from storage have been
drain the oil, and refill the system with new oil. accomplished. Clear form entries.
(17) Repeat steps (11) through (15). Evidence
of continued oil contamination requires a thorough (5) Perform daily inspection in accordance
investigation. with PMD cards.

SECTION IV – INTERMEDIATE STORAGE

E-12. INSPECTION PRIOR TO c. Check fuel, oil, and hydraulic Iines/,loses for
STORAGE. leakage.

d. Lubricate the helicopter for 50 and 100 hour


NOTE intervals in accordance with Chapter 1.
The general requirements of Section I are
a part of these procedures. e. Ensure that bolts, nuts, and washers removed
during disassembly are coated with corrosion ,
a. Ensure that all removed components are preventive compound (C86) and reinstalled in
preserved and either stowed in the helicopter or at a quantities and location exactly as removed from the
designated location. major component unless otherwise specified.

b. Ensure that all removed or disconnected f. Record the date and type of storage in the
components are entered in the helicopter records. helicopter records.

E-10.1/(E-10.2blank)
TM 55-1520-210-23-3

E-13. PRESERVATION. (7) Tag fuel cap to read THIS FUEL SYSTEM
HAS BEEN PRESERVED WITH MIL-L-6081OIL. Flush
a. Power-train. Preserve the power-train in with standard fuel before placing in service.
accordance with paragraph E-9a.
h. Damaged Fuel Systems.
b. Engine. Preserve operable and inoperable
engines in accordance with paragraphs E-9b and E- (1) Open fuel cells in accordance with Chapter
9c. 1, and ventilate tanks with rapidly moving dry air until
fumes are below the danger level as indicated by
c. Rotors and Controls. testing with a Combustible Gas Indicator.
(1) Preserve in accordance with paragraph E- [2) Preserve the tanks by spraying with oil
9d. (C192) through access openings. Coat the entire
interior surface.
(2) Color code and remove rotor blades, clean
with mild soap and water, place in blade containers,
(3) Tag the fuel system to read TANKS
and store under cover.
PRESERVED WITH MIL-L-6081 oil
d. Landing Gear. Process landing gear in i. Battery. Preserve battery in accordance with
accordance with paragraph E-9e. paragraph E-9i.
e, Hydraulic System. Preserve in accordance j. A i r f r a m e . E x c e p t f o r r o t o r blade
with paragraph E-9f. securement, prepare in accordance with paragraph
E-9
f. A v i o n i c s . Process in accordance with
paragraph E-9g.
E-14. MAINTENANCE OF
g. Fuel System.
PRESERVATION DURING
INTERMEDIATE STORAGE.

a. Inspect helicopter in accordance with local


Observe all safety precautions when directives and those requirements outlined in
purging fuel cells. Use only approved paragraph E-3.
equipment and methods. Refer to TM
55-1500-204-25/1. b. A p p l i c a b l e p o r t i o n s of preventive
maintenance daily inspection shall be performed at
(1) Drain the fuel tanks in accordance with feast once every 30 days in accordance with PMD
Chapter 1. cards.
c. If conditions change so that a helicopter
(2) Add five gallons diesel fuel and drain. This
prepared for Intermediate Storage is to remain in
should remove any residual fuel which puddled at the
storage for a longer period of time, represerve the
bottom of the tank. helicopter at the end of 180 days.
(3) Open fuel line and activate boost pump to
remove fuel at pump sump. E-15. DE PRESERVATION AFTER
INTERMEDIATE STORAGE.
(4) Repeat steps (2) and (3) using lubricat-
ing oil (C192).
a. Airframe. Depreserve helicopters in
(5) Spray the inside of the accessible tank accordance with paragraph E - 1 1 a ( 1 )
with oil (C192).
b. Electrical System. Prepare for flight in
(6) Drain the oil and test tanks with a accordance with paragraph E-11b.
Combustible Gas Indicator. If a dangerous level of fuel
fumes exists, flush tanks with fresh lubricating oil c. Avionics. Prepare for flight in accordance
until a safe reading is obtained. with paragraph E-11d.

Change 4 E-11
TM 55-1520-210-23-3

d. Hydraulics. Depreserve in accordance with SECTION V .


E-11e.
STORAGE OF AIRCRAFT
e. Landing Gear. Remove blocks or shoring UNDERGOING MAINTENANCE .
from under skid tubes
E-16 Helicopters in this category requ-
f, Rotors and Controls. ire individual determination as to the
degree of protection and inspection nece-
(1) Depreserve in accordance with paragraph ssary while undergoing maintenance. Vary-
E-11g. ing environmental conditions may justify
an increase or decrease in the degree of
protection needed. Some factors which
(2) Replace main and tail blades on hubs in should be considered are: humidity, temp-
same position as before removal. erature, actual location of aircraft
(hangered or outside). Depending on the
9 Power-train. Depreserve in accordance nature of the maintenance being performed
with paragraph E-11h certain inspections may not be necessary.
E-17. PRESERVATION.
h. Engine/Fuel System. In general, when appropriate, the
(1) Drain fuel tanks of any accumulated oil. preservation requirements of aircraft in
flyable storage are applicable to this
(2) Add five gallons operating fuel (C 119) to storage category. Aircraft that are hang-
flush tanks. Drain. ered are relieved from the ground run-up>
installation of protective covers, and
(3) Fill tanks with operating fuel. Check for the requirement for full fuel tanks. If
leaks. deemed appropriate, additional preserva-
tion measures from sections III and IV
(4) Depreserve engine in accordance with may be taken.
paragraph E-1 1i.
E-18. MAINTENANCE OF PRESERVATION OF
i. Miscellaneous AIRCRAFT UNDERGOING MAINTENANCE.
a. Daily inspections shall be schedul-
(1) Clean helicopter as necessary in ed at the discretion of the maintenance
accordance with Chapter 1. officer.
b. Helicopter shall be inspected in
(2) Ensure that all removed components have accordance with local directives and req-
been installed on/in helicopter. Check the records for uirements of preceding paragraph E-3 when
identification of components which have been applicable.
removed or disconnected. Check for subsequent
Installation or connection. E-19. DEPRESERVATION AFTER STORAGE DURING
MAINTENANCE.
(3) Determine that all related systems have General maintenance procedures shall
been properly depreserved and serviced before any be followed for release of aircraft after
system or component operational check is performed.
all maintenance action has been completed.
(4) Perform any necessary inspection
required by helicopter records in accordance with
Chapter 1
(5) Remove static ground wire.
(6) Ensure all necessary entries are made in
helicopter records and indicate in logbook that
helicopter has been depreserved and removed from
storage.

E-12 Change 4
TM 55-1520-210-23-3

APPENDIX F

WIRING DIAGRAMS

F-1, WIRING DIAGRAMS F-7. EQUIPMENT LISTS.

F-8. Description — Equipment Lists. Tables F-1


F-2. Description — Wiring Diagrams through F-4 list each item of equipment shown on the
This appendix contains wiring diagrams, electrical system wiring diagrams. Each item of
and essential wiring information for the equipment is identified by the reference designator
electrical systems and circuits in the UH-1 D/H and nomenclature.
helicopter to assist maintenance personnel in
understanding the circuits and components installed
in the helicopter and in troubleshooting and tracing of F-9. CONNECTOR REPLACEMENT
inoperative and malfunctioning circuits. CHART.

F-10. Description — Connector Replacement


NOTE Chart. The purpose of the connector replacement
chart (table F-5) is to provide maintenance-personnel
Master wiring diagrams are not furnished with necessary information to replace (resolder or
for helicopters S/N 65-9565 and crimp) a damaged electrical connector. The chart
subsequent. In lieu of master wiring contains the connector code item numbers, the
diagrams, individual system wiring connector pin letters or numbers, and the wire
diagrams are furnished to provide easier number that installs in each respective pin. Only
circuit analysis, troubleshooting, and those connectors that are not shown in their entirety
tracing of inoperative a n d / o r in one of the system diagrams are presented in table
malfunctioning circuits. F-5.

F-3. WIRING DATA.

F-4. Wire Identification. All wires on diagrams are


identified by coded wire numbers exactly as they are
marked in the helicopter. The coded wire numbers
indicate circuit function, wire number, wire segment
letter, and wire size (gage). (See figure F-1.)

F - 5 , Abbreviations. Abbreviations are in


accordance with MlL-STD-12C and AR310-50,
except when the abbreviation depicts a marking or
decal contained in or on the helicopter. F-11. WIRING DIAGRAM INDEX.

NOTE
F-6. Symbols. Wiring diagram component symbols
are drawn in accordance with ANSI Y14. 15, Part 1. System wiring diagrams with no
The symbols chart (figure F-2) illustrates electrical effectivity listing cover helicopter blocks
symbols used on the wiring diagrams. 65-9565 and subsequent.

F-1
TM 55-1520-210-23-3

Title Figure
Electrical Schematic (64-13492 thru 64-13901) ........................................................................................... F-3
Electrical Wiring Diagram (64-13492 thru 64-13901) ................................................................................... F-4
RPM Limit Warning Test Set ........................................................................................................................ F-5
RPM Limit Warning Test Set Schematic-BHT Model 205-074-033-103 ...................................................... F-6
Mission Antennas OE-201/ARQ-33 and OE-202/ARQ-33 ........................................................................... F-7
High Performance Hoist System .................................................................................................................. F-8
Door Gunners Foot Mike Switch .................................................................................................................. F-9
Altimeter AAU-31/A and AAU-321A and Transponder.................................................................................
AN/APX-72 Interconnecting Wiring Diagram ............................................................................................... F-10
Tachometer Generator System .................................................................................................................... F-11 1
AC Pressure Indicator System ..................................................................................................................... F-12
Temperature Bulb, Turn and Slip Indicator .................................................................................................. F-13
Exhaust Temperature Indicator System ....................................................................................................... F-14
Pilot Heater System...................................................................................................................................... F-15
Attitude Indicator System.............................................................................................................................. F-16
Fuel Quantity System ................................................................................................................................... F-17
HVE Battery System..................................................................................................................................... F-18
EB: Battery System ...................................................................................................................................... F-18.1
External Power System ................................................................................................................................ F-19
EB External 3 Phase Power System............................................................................................................ F-19.1
Generator and Bus System .......................................................................................................................... F-20
EB Generator and Bus System .................................................................................................................... F-20.1
AC Power System ........................................................................................................................................ F-21
EB Alternator System ................................................................................................................................... F-21.1
Starter System.............................................................................................................................................. F-22
External 3 Phase Power System.................................................................................................................. F-22.1
Ignition System ............................................................................................................................................. F-23
Cockpit, Dome and Crew Lights System...................................................................................................... F-24
Instrument, Console, and Pedestal Lights System....................................................................................... F-25
ARC-201 Panel Lighting (MWO 55-1520-210-50-21) .................................................................................. F-25.1
Night Vision Goggles.................................................................................................................................... F-25.2
Caution Lights System.................................................................................................................................. F-26
5-Volt Instrument Lighting System ............................................................................................................... F-26.1
RPM Warning System .................................................................................................................................. F-27
Landing and Searchlight System.................................................................................................................. F-28
Navigation, Fuselage, and Anticollision Lights System ................................................................................ F-29
De-ice and Ice Detector System................................................................................................................... F-30
Fuel Boost and Fuel Valve System .............................................................................................................. F-31
Governor Control and Idle Stop Systems..................................................................................................... F-32
Force Trim and Hydraulic Control System ................................................................................................... F-33
Cabin Heating System.................................................................................................................................. F-34
Heated Blanket Receptacle Wiring Diagram ................................................................................................ F-35
Windshield Wiper System ............................................................................................................................ F-36
Cargo Hook System ..................................................................................................................................... F-37
Rescue Hoist System ................................................................................................................................... F-38
High Performance Utility Helicopter Hoist System ....................................................................................... F-38.1
External Fuel System ................................................................................................................................... F-39
Fire Detector System.................................................................................................................................... F-40
Armament Wiring Diagram ........................................................................................................................... F-41
Electrical Schematic (62-2106 thru 62-2113, 62-12351 thru 62-12372) ...................................................... F-42
Electrical Wiring Diagram (62-2106 thru 62-2113, 62-12351 thru 62-12372) .............................................. F-43
Electrical Schematic (63-8739 thru 63-8859, 63-12956 thru 63-13002) ...................................................... F-44
Electrical Wiring Diagram (63-8739 thru 63-8859, 63-12956 thru 63-13002) .............................................. F-45

F-2 Change 8
TM 55-1520-210-23-3

Figure F-1. Wiring identification code

218-261 0 - 88 -19 F-3


TM 55-1520-210-23-3

Figure F-2. Electrical symbol chart (Sheet 1 of 2)

F-4
TM 55-1520-210-23-3

Figure F-2. Electrical symbol chart (Sheet 2 of 2)

F-5
TM 55-1520-210-23-3

Table F-1. Equipment List - Helicopters Serial No. 65-9565 Through 65-12895

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

Al Panel, DC Power E2 Detector, Magnetic Chip


A2 Panel, AC Power E3 Detector, Magnetic Chip
A3 Panel, Engine E4 Detector, Magnetic Chip
A4 Panel, Caution G2 Generator, 30 VDC (300A)
A6 Panel, Instrument Lights G3 Generator, Tach. (Gas Prod.)
A? Panel, Exterior Lights G4 Generator, Tach. (Pwr. Turb.)
A8 Panel, Hydraulic Control G5 Generator, Tach. (Rotor)
A10 Panel, Miscellaneous G6 Generator, Starter 28V (200A)
All Panel, Heating
A12 Cargo Hook Assembly HR1 Heater, Pitot Tube
A13 Panel, Resistor 11 Indicator, Attitude (Copilot)
A14 Panel, AC Circuit Breaker 12 Indicator, Fuel Quantity
A15 Panel, Overhead Console 13 Indicator, Torque - Pilot
A20 Panel Assembly, Aft Dome Lights 14 Indicator, Oil Pressure (Engine)
A21 Panel, Dome Lights & Pitot Heater 15 Indicator, Oil Pressure (XMSN)
A26 Panel, Assembly, Ext. Fuel 16 Indicator, Fuel Pressure
17 Indicator, Tach. (Gas Prod.)
B1 Syncro XMTR Torque Pressure 18 Indicator, Tach- Dual (Pilot)
B3 Syncro XMTR, XMSN Oil Pressure 19 Light, Utility (Pilot)
B3 Syncro XMTR, Engine Oil Pressure 110 Light, Dome
B4 Syncro XMTR, Fuel Pressure 111 Light, Search
B5 Motor, Fuel Shutoff Valve I 12 Light, Fire Warning
B6 Motor, R/H Fuel Boost Pump 113 Light, Master Caution
B7 Motor, Windshield Wiper 114 Light, Instrument Secondary
B8 Motor, R/H Aux. Fuel Pump I 15 Lamp, Instrument & Edge Lights
B12 Motor, Gov. RPM Actuator 116 Light, Landing
B13 Motor, L/H Aux. Fuel Pump I 17 Light, Left Navigation
B19 Motor, Bleed Air Valve 118 Light, Right Navigation
B31 Motor, Copilot Windshield Wiper I 19 Light, Tail
BT2 Battery I 20 Light, Top Fuselage
121 Indicator, XMSN Oil Temp.
Cl Capacitor, PF Corr. (MIL-C-25) 122 Indicator, Engine Oil Temp.
C 7 Capacitor, Filter, JN14 123 Indicator, Turn & Slip (Pilot)
CB1 Circuit Breaker (5A) 125 Light, XMSN Sump Inspect
CB2 Circuit Breaker (10A) 126 Light, Bottom Fuselage
C B3 Circuit Breaker (15A) I28 Light, Utility (Copilot)
CB4 Circuit Breaker (20A) 131 Indicator, Exh. Temp. (Pilot)
CB5 Circuit Breaker (25A) I 34 Standby Compass (Pilot)
CB6 Circuit Breaker (1A) I 40 Light, Anti-Collision
CB7 Circuit Breaker (35A) 142 Indicator, Attitude (Pilot)
CB8 Circuit Breaker (2A) I 44 Light, Cargo Release Armed
CB11 Circuit Breaker (7.5A) 145 Light, Hi-Lo RPM Warn.
CB12 Circuit Breaker (50A) 172 Light, Air Filter, Warning
CP1 Coupler, Fuel Qty. Sys. “J” Box, J2 Recept. Pitot Tube Heater
Unshielded J3 Recept. Instrument Panel Disc.
CP2 Coupler, Fuel Qty. Sys. "J" Box, J4 Recept. Fuel Quantity Ind.
Shielded J5 Recept. Fuel Pressure Ind.
CR2 Diode, Ext. Power Relay J6 Recept. Copilot Att. Ind.
CR30 Diode, Batt. Voltage Fwd. Loc J? Recept. Engine Oil Temperature Ind.
CR31 Diode, Batt. Voltage Aft Loc J8 Recept. Engine Oil Pressure Ind.
J9 Recept. Pilot Dual Tach. (Rotor)
D1 Inverter, 250 V.A. 3 Ph (Main) J10 Recept. Pilot Dual Tach. (Pwr. Turb.)
D2 lnverter, 250 V.A. 3 Ph (Spare) J11 Recept. XMSN Oil Temperature Ind.
DS1 Control Assembly, RPM Warn. Recept. XMSN Oil Pressure Ind.
J12
J13 Recept. Pilot 5V Power Supply
E1 Detector, Magnetic Chip J14 Recept. Copilot 5V Power Supply

F-6
TM 55-1520-210-23-3

Table F-1. Equipment List - Helicopters Serial No. 65-9565 Through 66-12895 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

J15 Recept. Pilot Torque Meter J106 Recept. Heated Blanket R/H
J16 Recept. Pilot Turn & Slip Indicator J107 Recept. Copilot Collective Stick
J17 Recept. Gas Prod. Tach. J108 Recept. Fuel Diff. Pressure Sw.
J20 Recept. Pilot Cyclic Stick J109 Recept. Ext. Power
J21 Recept. Hydraulic Control Panel J110 Recept. Anti-Collision Lt. Disc.
J22 Recept. Copilot Cyclic Stick J1ll Recept. Anti-Collision Lt.
J23 Recept. Engine Panel J112 Recept. Msg. Brake, Anti-Torque
J24 Recept. Caution Panel J113 Recept. Msg. Brake, Fore & Aft
J25 Recept. Pilot Collective Stick J114 Recept. Msg. Brake Lat.
J26 Recept. Windshield Wiper J115 Recept. Test-Eng. Vibration Meter
J28 Recept. Hydraulic Bypass Solenoid J127 Recept. Var. Mix Valve Disc.
J29 Recept. Hydraulic Press. Warning Sw. J129 Recept. Displacement-Roll & Pitch Gyro
J31 Recept. Cargo Hook J130 Recept. Rate Switching Gyro
J32 Recept. Cargo Sling Disc. J131 Recept. Attitude Ind.
J35 Recept. Rotor, Tach. Gen. J135 Recept. Ice Interpreter
J36 Recept. XMSN Oil Pressure Sw. J136 Recept. Ice Interpreter
J37 Recept. XMSN Oil Temperature Bulb J138 Recept. Door Post Outlet Valve Act.
J38 Recept. Copilot Windshield Wiper J146 Recept. Bleed Air Valve
J39 Recept. XMSN Oil Pressure XMTR J147 Recept. Internal Aux. Fuel Disc. L/H
J41 Recept. XMSN Disc. J148 Recept. Internal Aux. Fuel Disc. R/H
J42 Recept. Fuel Tank Disc. L/H J155 Recept. Hi-Lo RPM Warn.
J43 Recept. Compensator Fuel Tank Disc L/H J156 Recept. Eng. Fuel Filter Bypass Sw.
J44 Recept. Fuel Tank Disc L/H J166 Recept. Aft, Outlet Valve
J53 Recept. Bulkhead Feed-thru-Aft Fuel Cell J191 Recept. Main Inverter Power
J54 Recept. Bulkhead Feed-thru-Aft Fuel Cell J192 Recept. Spare Inverter Power
J57 Recept. Ext. Fuel Cont. Panel J194 Recept. Engine Chip Detector
J60 Recept. Socket, Relay-Gen Field J1017 Recept. Ext. Fuel Disc. L/H
J64 Recept. Torque Press. XMTR J1024 Recept. Ext. Fuel Disc. R/H
J65 Recept. Engine Oil Press. XMTR
J66 Recept. Fuel Pressure XMTR K1 Relay, External Power
J68 Recept. Disc. Muff Heater K2 Relay, Non- Essential Bus
J71 Recept. Engine Fuel Valve K3 Relay, Starter
J72 Recept. Engine Oil Pressure Sw. K4 Relay, Bus Cont. (Gen. Fail)
J74 Recept. Batt. Disc. K5 Relay, Reverse Curr (Main)
J75 Recept. Navigation Lts. Flasher K6 Relay, Over Voltage
J77 Recept. Ice-Detector K7 Relay, Generator Field
J 80 Recept. Engine Air Pressure Sw. K8 Relay, AC Failure
J81 Recept. Starter Deck K9 Relay, Battery
J84 Recept. De-Icing, Hot Air Valve K10 Relay, Fuel Transfer
J85 Recept. Engine Oil Temp. Bulb K23 Relay, Standby Gen. Rev. Curr
J 86 Recept. Power Turb. Tach. K24 Relay, Cargo, Hook Release
J87 Recept. Gas Turb. Tach. K27 Relay, Inverter
J88 Recept. Ignition Unit, Engine K35 Relay, Main Invtr. Power
J89 Recept. Primer Valve (Fuel Ign. Sol.) K36 Relay, Spare Invtr. Power
J90 Recept. Fuel Cont. Sol. Valve K37 Relay, Lo- Fuel Caution Light
J91 Recept. Engine Disc. K38 Relay, Lo- Fuel Caution Light
J92 Recept, Engine Fwd. Disc. K46 Relay, Overheat
J93 Recept. Fire Det. Fwd. Disc. K65 Relay, Battery, Aft Loc
J94 Recept. Fire Det. Element R/H K66 Relay, Battery Feeder
J95 Recept. Fire Det. Element L/H
J96 Recept. Fire Det. Element R/H L1 Solenoid, Primer (Ignition)
J97 Recept. Fire Det. Element L/H L2 Solenoid, Fuel Cont. Valve
J98 Recept. Tail Light Disc. L4 Solenoid, Hydraulic Bypass
J99 Recept. Thermocouple Disc. L6 Solenoid, Hot Air De-icer
J102 Recept. Standby Compass (Pilot) L? Solenoid, Idle Stop Rel.
J105 Recept. Heated Blanket L/H L8 Msg. Brake Anti-Torque Force Trim

F-7
TM 55-1520-210-23-3

Table F-l. Equipment List - Helicopters Serial No. 65-9665 Through 65-12895 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
--–-–---– –
L9 Msg. Brake Fore & Aft Force Trim P66 Plug, Fuel Press. XMTR
L10 Msg. Brake Lat. Force Trim P68 Plug, Muff Heater Disc.
L14 Solenoid, Door Post Htr. Outlet Valve P71 Plug, Fuel Valve Shut-off
L15 Solenoid, Aft Outlet Valve Act. P72 Plug, Engine Oil Press. Sw.
Ml Meter, DC Load (Stand-By-Gen.) P74 Plug, Battery Disc. Fwd.
M2 Meter, DC Volts P75 Plug, Navigation Lights Flasher
M3 Meter, AC Volts P77 Plug, Ice Detector
M4 Meter, DC Load (Main Gen) P80 Plug, Eng. Air Pressure SW.
P81 Plug, Starter Deck
02 Guard - Generator SW-DC Pwr. Panel P84 Plug, De-Iceing Hot Air Valve
P2 Plug, Pitot Tube Heater P85 Plug, Oil Temp. Bulb
P3 Plug, Instrument Panel Corm. P86 Plug, Power Turb. Tach.
P4 Plug, Fuel Qty. Ind. P87 Plug, Gas Prod. Tach.
P5 Plug, Fuel Press. Ind. P88 Plug, Ignition Unit- Eng.
P6 Plug, Copilot Att. Ind. P89 Plug, Ignition Sol. Valve
P? Plug, Engine Oil Temp. Ind. P90 Plug, Fuel Cont. Sol. Valve
P8 Plug, Engine Oil Press. Ind. P91 Plug, Engine Disc.
P9 Plug, Pilot Dual Tach. (Rotor) P92 Plug, Engine Forward Disc.
Pl0 Plug, Pilot Dual Tach. (Pwr. Turb.) P93 Plug, Fire Det. Forward Disc.
P11 Plug, XMSN Oil Temp. Ind. P94 Plug, Fire Det. Element R/H
P12 Plug, XMSN Oil Press. Ind. P95 Plug, Fire Det. Element L/H
P13 Plug, Pilot 5V Power Supply P96 Plug, Fire Det. Element R/H
P14 Plug, Copilot 5V Power Supply P97 Plug, Fire Det. Element L/H
P15 Plug, Pilot, Torque Meter P98 Plug, Tail Light Disc.
P16 Plug, Pilot, Turn & Slip Ind. P99 Plug, Thermocouple Disc. - Engine
P17 Plug, Gas Prod. Turb. Tach P99A Plug, Thermocouple Disc. - Engine
P20 Plug, Pilot’s Cyclic Stick P99B Plug, Thermocouple Disc. - Engine
P21 Plug, Hydraulic Cont. Panel P102 Plug, Standby Compass (Pilot)
P22 Plug, Copilot Cyclic Stick P107 Plug, Copilot Coil. Stick
P23 Plug, Engine Panel P108 Plug, Fuel Diff. Press. Sw.
P24 Plug, Caution Panel P110 Plug, Anti-Collision Light Disc.
P25 Plug, Pilot Collective Stick P1ll Plug, Anti- Collision Light
P26 Plug, Windshield Wiper P112 Plug, Msg. Brake Anti-Torque
P28 Plug, Hyd. Bypass Sol. Valve P113 Plug, Msg. Brake Fore and Aft
P29 Plug, Cargo Hook P114 Plug, Displacement, Roll & Pitch Gyro
P32 Plug, Cargo Hook Disc. P130 Plug, Rate Switching Gyro
P35 Plug, Rotor Tach. Gen. P131 Plug, Attitude Ind.
P36 Plug, XMSN Oil Pressure Sw. P135 Plug, Ice-Interpreter
P37 Plug, XMSN Oil Temp. Bulb P136 Plug, Ice-Interpreter
P38 Plug, Copilot Windshield Wiper P138 Plug, Door Post - Aft Outlet Valve Act.
P39 Plug, XMSN Oil Press. XMTR P146 Plug, Bleed Air Valve
P41 Plug, XMSN Disc. P147 Plug, Unshielded Tank Coupler Disc.
P42 Plug, Shielded Tank Unit Disc L/H Tank P148 Plug, Unshielded Tank Coupler Disc.
P43 Plug, Monitor Tank Unit DISC L/H Tank P149 Plug, Unshielded Tank Coupler Disc.
P44 Plug, Unshielded Tank Unit Disc. P151 Plug, Shielded Tank Coupler Disc.
L/H Tank P152 Plug, Shielded Tank Coupler Disc.
P46 Plug, Fuel Tank Disc. L/H Cell P153 Plug, Shielded Tank Coupler Disc.
P47 Plug, Fuel Tank Disc. L/H Cell P155 Plug, Hi-Lo RPM Warning
P48 Plug, Fuel Tank Disc. L/H Cell P156 Plug, Engine Fuel Filter Bypass
P53 Plug, Unshielded Tank Unit Aft Cell P166 Plug, Aft Outlet Valve
P54 Plug, Shielded Tank Unit Aft Cell P191 Plug, Inverter Disc. - Main
P55 Plug, Fuel Tank Disc. - Aft Cell P192 Plug, Inverter Disc. - Spare
P56 Plug, Fuel Tank Disc. - Aft Cell P194 Plug, Engine Chip Detector
P57 Plug, Ext. Fuel Cont. Panel P1017 Plug, Ext. Fuel Disc. L/H
P60 Plug, Field Relay Gen. P1024 Plug, Ext. Fuel Disc. R/H
P64 Plug, Torque Press. XMTR PS1 Pilot, 5V Power Supply (PS-274B)
P65 Plug, Eng. Oil Press. XMTR PS2 Copilot, 5V Power Supply (PS-274B)
TM 55-1520-210-23-3

Table F-1. Equipment List - Helicopters Serial No. 65-9565 Through 65-12895 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

R1 Shunt, Ammeter (Stby-Gen.) S63 Switch, Ext. Fuel Jett.


R2 Shunt, Ammeter (Main Gen.) S68 Switch, Force Trim
R3 Resistor, Windshield Wiper S70 Switch, Starter-Generator
R4 Rheostat, Pilot Inst. Light Dim. S73 Switch, Overheat Bleed Air
R5 Rheostat, Sec. Instrument Light Dim S75 Switch, Search (ON STOW)
R6 Rheostat, Overhead Console S76 Switch, Landing Light (ON-OFF)
R7 Resistor, Navigation Lights Dim S77 Switch, Starter (Co pilot Coil.)
R8 Rheostat, Peal. Lights Dim S78 Switch, Cargo Rel. (Copilot)
R9 Rheostat, Eng. Inst. Light Dim S79 Switch, Fuel Ejector FLOW Sw. L/H
R10 Rheostat j Copilot Inst. Lights Dim S80 Switch, Fuel Ejector Flow Sw. R/H
R11 Resistor, Fire Det. Cont. S81 Switch, De-Ice (ON-OFF)
R12 Resistor, Spool Thermocouple S83 Switch, Bleed Air (ON-OFF)
R21 Rheostat, Aft Dome Lights S84 Switch, Bleed Air (HT-DEF)
R26 Rheostat, Course Ind. Light Dim S85 Switch, Aft Outlet (Htr)
R27 Resistor, AC Load Balancing S87 Switch, Aft- Outlet Limit
S88 Switch, Start Fuel
S1 Switch, Aft Dome Light S93 Switch, Hi-Low RPM
S2 Switch, Rotary (AC VM Sel.) S94 Switch, Fuel Filter Bypass
S4 Switch, XMSN Sump Insp. Light Sill Switch, Fuel Trans. Pump
S5 Switch, Fuel Quantity Test S112 Switch, Pilot Hoist Cont.
S6 Switch, Starter (Pilot Coil.) S114 Switch, Fire Control
S7 Switch, Hydraulic Boost Cont. S115 Switch, Fire Control
S8 Switch, Gen. (ON-OFF Reset) S124 Switch, Sel-Windshield Wiper
S9 Switch, Pitot Heater S134 Switch, Chip Det. Sel.
Sl0 Switch, Force Trim (Copilot Cyc.) S195 Switch, Diff. Pressure
S11 Switch, Rotary (AC VM Sel.)
S12 Switch, Searchlight Cont. T1 Transformer 115/28V
S13 Switch, Navigation Lights (Flash Steady) TB1 Term. Blk, Forward Inst. Panel.
S14 Switch, Nav. Lights (Bright- Dim) TB2 Term. Blk. Overhead Console R/H
S18 Switch, Force Trim (Pilot Cyc.) TE3 Term. Blk. Overhead Console L/H
S20 Switch, Test (Fire Det.) TB4 Term. Blk. Aft Fuel Cell
S23 Switch, Windshield Wiper TB9 Term. Blk. Top Ext. & Dome Lights
S25 Switch, Landing Lt. (Ext. -Retr) TB12 Term. Blk. Peal. Panel Edge Lights
S26 Switch, XMSN Oil Temp. TB13 Term. Blk. Inst. Panel Lights
S27 Switch, Hydraulic Pressure TB14 Term. Blk. Inst. Panel Sec. Ligh
S28 Switch, XMSN Oil Pressure Warn. TB15 Term. Blk. Cockpit Lights L/H
S29 Switch, Engine Oil Pressure Warn. TB16 Term. Blk. Cockpit Lights R/H
S31 Switch, Limit (Ext. Power Door) TB25 Term. Blk. Thermocouple Ind.
S32 Switch, Cargo Release (Pilot) TB26 Term. Blk. DC Grid. & Audio
S33 Switch, Governor (Auto-Emer.) TB27 Term. Blk. Aft Thermo Lead
S35 Switch, Forward Dome Light TB29 Term. Blk. Instrument Grid.
S36 Switch, Cargo Release TB34 Term. Blk. Aft Dome Lt. Panel.
S37 Switch, RPM Gov. (Pilot) TB35 Term. Blk. R/H Fuel Cell
S38 Switch, Fuel (ON-OFF) TB36 Term. Blk. Ext. Power Diode
S39 Switch, Inverter (Main-Spare) TB38 Term. Blk. L/H Fuel Cell
S40 Switch, Battery (ON-OFF) TB39 Term. Blk. Electrical Compt. Aft
S41 Switch, Upper Float TB60 Term. Blk. Batt. Voltage, Forward
S42 Switch, Lower Float TB61 Term. Blk. Batt. Voltage, Aft
S44 Switch, Fuel- Low Level TB100 Term, Blk. Pilot and Copilot 5V Power Supply
S45 Switch, Fuel- Transfer L/H VR1 Regulator - Voltage (Main Gen.)
S46 Switch, Fuel-Transfer R/H VR2 Regulator - Voltage (Stby Gen.)
S50 Switch, Idle Stop Rel (Pilot)
S51 Switch, RPM Gov. (Copilot) W1 Cable Assembly, Fire Det.
S58 Switch, Fuel Diff. Pressure
S59 Switch, Anti- Coil. Light Z2 Engine Ignition Unit
S62 Switch, Non-Ess Bus Cont. Z3 Flasher Unit - Navigation Lights

F-9
TM 55-1520-210-23-3

Table F-1. Equipment List - Helicopters Serial No. 65-9565 Through 65-12895 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
Z5 XMSN Oil Temperature Bulb Z16 Fuel Qty. Tank Unit - Aft
Z6 Engine Oil Temperature Bulb Z17 Displacement - Roll and Pitch
Z8 Ice Interpreter Gyro
Z9 Fire Det. Cont. Z18 Rate Switching Gyro
Z13 Ice Detector Z22 Fuel Qty. Tank Unit R/H Forward

F-10
TM 55-1520-210-23-3

Table F-2. Equipment List- Helicopters Serial No. 66-746 Through 66-17144

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

A1 Panel, DC Power E1 Detector, Magnetic Chip


A2 Panel, AC Power E2 Detector, Magnetic Chip
A3 Pariel, Engine E3 Detector, Magnetic Chip
A4 Panel, Caution E4 Detector, Magnetic Chip
A6 Panel, Instrument Lights
A7 Panel, Exterior Lights G2 Generator, 30 VDC (300A)
Panel, Hydraulic Cont. G3 Generator, Tach. (Gas Prod.)
A10 Panel, Misc. Generator, Tach. (Pwr. Turb.)
A11 Panel, Heating G5 Generator, Tach (Rotor)
A12 Cargo, Hook Assembly G6 Generator, Starter 28V (200A)
A13 Panel, Resistor HR1 Heater, Pilot Tube
A14 Panel, AC Circuit Breaker
A15 Panel, Overhead Console I1 Indicator, Attitude (Copilot)
A20 Panel, Assembly Aft Dome Lts. I2 Indicator, Fuel Qty.
A21 Panel, Dome Light Pitot Heater I3 Indicator, Torque - Pilot
A26 Panel, Assembly Ext. Fuel Indicator, Oil Press. (Eng.)
I5 Indicator, Oil Press. (XMSN)
B1 Synchro XMTR, Torque Press. I6 Indicator, Fuel Pressure
B3 Synchro XMTR, XMSN Oil Press. I7 Indicator, Tach. (Gas Prod.)
B3 Synchro XMTR, Eng. Oil Press. I8 Indicator, Tach. Dual (Pilot)
B4 Synchro XMTR, Fuel Press. I9 Light, Utility (Pilot)
B5 Motor, Fuel Shut-Off Valve I10 Light, Dome
B6 Motor, R/H Fuel Boost Pump I11 Light Search
B7 Motor, Windshield Wiper I12 Light, Fire Warning
B8 Motor, R/H Aux. Fuel Pump 13 Light, Master Caution
B12 Motor, Gov. RPM Actuator I14 Light, Instrument Secondary
B13 Motor, L/H Aux. Fuel Pump I15 L amp, Instrument & Edge Lights
B19 Motor, Bleed Air Valve I16 Light, Landing
B22 Motor, Boom Actuator Hoist I17 Light, Left Navigation
B31 Motor, Copilot Windshield Wiper I18 Light, Right Navigation
B33 Motor, Winch Assy. Hoist I19 Light, Tail
B34 Motor, Bleed Air Valve I20 Light, Top Fuselage
BT2 Battery I21 Indicator XMSN Oil Temp.
I22 Indicator, Engine Oil Temp.
C1 Capacitor, PF (Corr (MIL-C-25) I23 Indicator, Turn & Slip (Pilot)
C7 Capacitor, Filter I25 Light, XMSN Sump Inspect
CB1 Circuit Breaker (5A I26 Light, Bottom Fuselage
CB2 Circuit Breaker (10A) I28 Light, Utility (Copilot)
CB3 Circuit Breaker (15A) I31 Indicator, Exhaust Temp. (Pilot)
CB4 Circuit Breaker (20A) I34 Standby, Compass (Pilot)
CB5 Circuit Breaker (25A) I40 Light, Anti-Collision
CB6 Circuit Breaker (1A) I42 Indicator, Attitude (Pilot)
CB7 Circuit Breaker (35A) I44 Light, Cargo Release Armed
CB8 Circuit Breaker (2A) I45 Light, Hi- Lo RPM Warn.
CB11 Circuit Breaker (7.5A) I72 Light, Air Filter Warning
CB12 Circuit Breaker (50A)
CP1 Fuel Qty. Sys. “J” Box, Unshielded Recept. Pitot Tube Heater
CP2 Fuel Qty. Sys. “J” BOX Shielded J3 Recept. Instr, Panel Disc.
CR2 Diode, External Power Relay Recept, Fuel Qty. Ind,
CR30 Diode, Batt. Voltage Fwd. Loc J5 Recept. Fuel Press. Ind.
CR31 Diode, Batt. Voltage Aft Loc Recept. Copilot Att. Ind.
J7 Recept, Engine Oil Temp. Ind.
D1 Inverter (Main) J8 Recept, Engine Oil Press. Ind.
D2 Inverter (Spare J9 Recept. Pilot Dual Tach. Rotor
DS1 Control Assy, PM Warning J10 Recept. Pilot Dual Tach. Pwr, Turb.

F-11
TM 55-1520-210-23-3

Table F-2. Equipment List - Helicopters Serial No. 66-746 Through 66-17144 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
J11 Recept. XMSN Oil Temp. Ind. J102 Recept. Standby Compass (Pilot)
J12 Recept. XMSN Oil Press. Ind. J105 Recept. Heated Blanket L/H
J13 Recept. Pilot 5V Power Supply J106 Recept. Heated Blanket R/H
J14 Recept, Copilot 5V Power Supply J107 Recept. Copilot Collective Stick
J15 Recept. Pilot Torque Meter J108 Recept. Fuel Diff. Press. Sw.
J16 Recept. Pilot Turn & Slip Ind. J109 Recept. External Power
J17 Recept. Gas Prod. Tach. J110 Recept. Anti-Collision Light Disc.
J20 Recept. Pilot Cyclic Stick J111 Recept. Anti-Collision Light
J21 Recept. Hydraulic Cont. Panel J112 Recept. Msg. Brake Anti-Torque
J22 Recept. Copilot Cyclic Stick J113 Recept. Msg. Brake Fore & Aft
J23 Recept. Engine Panel J114 Recept. Msg. Brake - Lat.
J24 Recept. Caution Panel J115 Recept. Test-Eng. Vibration Meter
J25 Recept. Pilot Collective Stick J119 Recept. Cabin Roof Disc. Hoist
J26 Recept. Windshield Wiper (Pilot) J127 Recept. Var. Mix. Valve Disc.
J28 Recept. Hydraulic Bypass Sol. J129 Recept. Displacement Roll & Pitch Gyro
J29 Recept. Hydraulic Press. Warning Sw. J130 Recept. Rate Switch Gyro
J31 Recept. Cargo Hook J131 Recept. Attitude Ind.
J32 Recept. Cargo Sling Disc. J135 Recept. Ice Interpreter
J35 Recept. Rotor, Tach. Gen. J136 Recept. Ice Interpreter
J36 Recept. XMSN Oil Press. Sw. J138 Recept. Door Post Outlet Valve Act.
J37 Recept. XMSN Oil Temp. Bulb J146 Recept. Bleed Air Valve
J38 Recept, Copilot Windshield Wiper J147 Recept. Internal Aux. Fuel Disc L/H
J39 Recept. XMSN Oil Press. XMTR J148 Recept. Internal Aux. Fuel Disc. R/H
J41 Recept. XMSN Disc. J155 Recept. Hi-Lo RPM Warning
J42 Recept. Fuel Tank Disc. L/H J156 Recept. Engine Fuel Filter Bypass Sw.
J43 Recept. Compensator Fuel Tank Disc L/H J166 Recept. Aft Outlet Valve
J44 Recept. Fuel Tank Disc. L/H J191 Recept. Main Inverter Power
J53 Recept. Bulkhead Feed-thru-Aft Fuel Cell J102 Recept. Spare Inverter Power
J54 Recept. Bulkhead Feed- thru-Aft Fuel Cell J194 Recept. Engine Chip Detector
J57 Recept. Ext. Fuel Cont. Panel J268 Recept. Hoist Cont. Box
J60 Recept. Socket, Relay-Gen-Field J269 Recept. Hoist Cont. Box
J64 Recept. Torque Press. XMTR J270 Recept. Hoist Cont. Box
J65 Recept. Engine Oil Press. XMTR J271 Recept. Hoist Cont. Box
J66 Recept. Fuel Press. XMTR J272 Recept. Hoist Cont. Box
J68 Recept. Disc. Muff Heater J273 Recept. Hoist Cont. Pendent
J71 Recept. Engine Fuel Valve J274 Recept. Hoist Boom Act.
J72 Recept. Engine Oil Press. Sw. J275 Recept. Hoist Winch Assembly
J74 Recept. Battery Disc. J1017 Recept. Ext. Fuel Disc. L/H
175 Recept. Navigation Lights Flasher J1024 Recept. Ext. Fuel Disc. R/H
J 77 Recept. Ice Detector
J80 Recept. Engine Air Filter Press. Sw. K1 Relay, Ext. Power
J81 Recept. Starter-Deck K2 Relay, Non-Ess Bus
J84 Recept. De-Icing Hot Air Valve K3 Relay, Starter
J85 Recept. Engine Oil Temp. Bulb K4 Relay, Bus Cont. (Gen Fail)
J86 Recept. Power Turbine Tach. KS Relay, Reverse Curr. (Main)
J87 Recept. Gas Turbine Tach. K6 Relay, Overvoltage
J89 Recept. Primer Valve (Fuel Ign. Sol.) K? Relay, Gen Field
J90 Recept. Fuel Cont. Sol. Valve K8 Relay, AC Failure
J91 Recept. Engine Disc. K9 Relay, Battery
J92 Recept. Engine Forward Disc. K10 Relay, Fuel Transfer
J93 Recept. Fire Det. Forward Disc. K15 Relay, Standby Gen Field
J94 Recept. Fire Det. Element R/H K23 Relay, Standby Gen. Rev. Curr.
J95 Recept. Fire Det. Element L/H K24 Relay, Cargo Hook Release
J96 Recept. Fire Det. Element R/H K27 Relay, Inverter
J97 Recept, Fire Det. Element L/H K32 Relay, Hoist Power
J98 Recept, Tail Light Disc. K35 Relay, Main Invtr. Power
J99 Recept. Thermocouple Disc. K36 Relay, Spare Invtr. Power

F-12
TM 55-1520-210-23-3

Table F-2. Equipment List - Helicopters Serial No. 66-746 Through 66-17144 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
P146 Plug, Bleed Air Valve S25 Switch, Landing Lt. (Ext. Retr)
P147 Plug, Unshielded Tank Coupler Disc. S26 Switch XMSN Oil Temp.
P148 Plug, Unshielded Tank Coupler Disc. S27 Switch, Hydraulic Press.
P149 Plug, Unshielded Tank Coupler Disc. S28 Switch, XMSN Oil Press. Warn.
P151 Plug, Shielded Tank Coupler Disc. S29 Switch, Eng. Oil Press. Warn.
P152 Plug, Shielded Tank Coupler Disc. S31 Switch, Limit (Ext. Pwr. Door)
P153 Plug, Shielded Tank Coupler Disc. S32 Switch, Cargo Release (Pilot)
P155 Plug, Hi- Lo RPM Warning S33 Switch, Gov. (Auto- Emer)
P156 Plug, Engine Fuel Filter Bypass S35 Switch, Fwd. Dome Lt.
P166 Plug, Aft Outlet Valve S36 Switch, Cargo Release
P191 Plug, Inverter Disc. - Main S37 Switch, RPM Gov. (Pilot)
P192 Plug, Inverter Disc. - Spare S38 Switch, fuel (ON-OFF)
P194 Plug, Engine Chip Detector S39 Switch, Invtr (Main - Spare)
P268 Plug, Hoist to Ship S40 Switch, Battery (ON-OFF)
P269 Plug, Cable, Out & Up Limit S41 Switch, Upper Float
P270 Plug, Hoist to Cont. Pendant S42 Switch, Lower Float
P271 Plug, Boom Act. S44 Switch, Fuel - Low Level
P272 Plug, Hoist to Winch Assy S45 Switch, Fuel - Transfer L/H
P273 Plug, Cont. Pendant S46 Switch, Fuel - Transfer R/H
P274 Plug, Boom Act. S49 Switch, J-2 Comp. De-slave
P275 Plug, Winch Assembly S50 Switch, Idle Stop Rel. (Pilot)
P1017 Plug, Ext. Fuel Disc. L/H S51 Switch, RPM Gov. (Copilot)
P1024 Plug, Ext. Fuel Disc. R/H S58 Switch, Fuel Diff. Press.
PSI Pilot, 5V Power Supply S59 Switch, Anti- Coil. Light
PS2 Copilot, 5V Power Supply S62 Switch, Non- Ess Bus Cont.
R1 Shunt, Ammeter (Stby Gen.) S63 Switch, Ext. Fuel Jett.
R2 Shunt, Ammeter (Main Gen.) S68 Switch, Force Trim
R3 Resistor - Windshield Wiper S70 Switch, Starter Gen.
R4 Rheostat, Pilot Inst. Lt. Dim S73 Switch, Overheat Bleed Air
R5 Rheostat, Sec. Inst. Lt. Dim S75 Switch, Searchlight (ON-STOW)
R6 Rheostat, Overhead Console S76 Switch, Landing Light (ON-OFF)
R7 Resistor, Navigation Lts. Dim S77 Switch, Starter (Copilot Coil)
R8 Rheostat, Peal. Lights Dim S78 Switch, Cargo Rel (Copilot)
R9 Rheostat, Engine Inst. Lights Dim S79 Switch, Fuel Ejector Flow Sw. L/H
R1O Rheostat, Copilot Inst. Lights Dim S80 Switch, Fuel Ejector Flow Sw. R/H
R11 Resistor, Fire Det. Cont. S81 Switch. De-Ice (ON-OFF)
R12 Resistor, Spool Thermocouple S83 Switch, Bleed Air (ON-OFF)
R21 Rheostat, Aft Dome Lts. S84 Switch, Bleed Air (Ht-Def)
R26 Rheostat, Course Ind. Lt. Dim S85 Switch, Aft Outlets (Htr)
R27 Resistor, AC Load Balancing S87 Switch, Aft Outlet Limit
S1 Switch, Aft Dome Lt. S88 Switch, Start Fuel
Switch, Rotary (DC VM Sel) S93 Switch, Hi- Lo RPM
S2 S94 Switch, Fuel Filter Bypass
S4 Switch, XMSN Sump Inspection Lt. S96 Switch, Cable Cut
S5 Switch, Fuel Qty. Test S97
S6 Switch, Starter (Pilot Coil) Switch, Cable Up Limit
Switch, Hydraulic Boost Cont. S101 Switch, Overload Sense
S7 Sill Switch, Fuel Trans Pump
S8 Switch, Gen. (ON-OFF-RESET) S112 Switch, Pilot Hoist Cont.
S9 Switch, Pitot Heater S114 Switch, Fire Control
Sl0 Switch, Force Trim (Copilot Cyc.) S115 Switch, Fire Control
S11 Switch, Rotary (AC VM Sel) S124 Switch, Sel- W/Wiper
S12 Switch, Searchlight Cont. S134 Switch, Chip Det. Sel
S13 Switch, Nav. Lts. (Flash Steady) S195 Switch, Diff. Press.
S14 Switch, Nav. Lts. (Bright-Dim)
S18 Switch, Force Trim (Pilot Cyc.) T1 Transformer 115/28V
S20 Switch, Test (Fire Det.) RB1 Term. Blk. Fwd. Inst. Panel
S23 Switch, Windshield Wiper

F-14
TM 55-1520-210-23-3

Table F-2. Equipment List - Helicopters Serial No. 66-746 Through 66-17144 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

TB2 Term. Blk. Overhead Console R/H W1 Cable Assembly


TB3 Term. Blk. Overhead Console L/H
TB4 Term. Blk. Aft Fuel Cell Z2 Engine, Ignition Unit
TB9 Term. Blk. Top Ext. & Dome Lts. Z3 Flasher Unit - Nav. Lts.
TB12 Term. Blk Peal. Panel Edge Lts. Z5 XMSN Oil Temp. Bulb
TB13 Term. Blk. I n s t . P a n e l L t s . Z6 Engine Oil Temp. Bulb
TB14 Term. Blk. Inst. Panel Sec. Lts. Z8 Ice Interpreter
TB15 Term. Blk. C o c k p i t L t s L / H Z9 Fire Det. Cont.
TB16 Term. Blk. C o c k p i t L t s . R / H Z13 Ice Detector
TB25 Term. Blk. T h e r m o c o u p l e I n d . Z16 Fuel Qty. Tank Unit - Aft
T B26 Term. Blk. DC Gnd & Audio Z17 Displacement - Roll * Pitch Gyro
TB27 Term. Blk. A f t T h e r m o L e a d Z18 Rate Switching Gyro
TB29 Term. Blk. I n s t . G r o u n d Z22 Fuel Qty. Tank Unit R/H Fwd.
TB34 Term. Blk. Aft Dome Lt. Panel Z24 Hoist Control Box
TB35 Term. Blk. R / H F u e l C e l l Z25 Hoist Cable Cutter
TB36 Term. Blk. E x t . P o w e r D i o d e Z41 Hoist Control Pendant
TB38 Term. Blk. Left-hand Fuel Cell
TB39 Term. Blk. E l e c . C o m p t . A f t NOTES
TB45 Term. Blk. Pitot Heater - Disc.
TB60 Term. Blk. Battery Voltage, Fwd. EFF 66-16868 thru 66-17144
TB61 Term. Blk. Battery Voltage, Aft
TB100 Term. Blk. Pilot and Copilot 5V Power Supply EFF 66-746 through 66-16867
VR1 Regulator - Voltage (Main Gen)
EFF 66-746 through 66-1210, 66-16000
VR2 Regulator, Voltage (Stby Gen.)
through 66-16033

F-15
TM 55-1520-210-23-3

Table F-2. Equipment List - Helicopters Serial No. 66-746 Through 66-17144 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

TB2 Term. Blk. Overhead Console R/H W1 Cable Assembly


TB3 Term. Blk. Overhead Console L/H
TB4 Term. Blk. Aft Fuel Cell Z2 Engine, Ignition Unit
TB9 Term. Blk. Top Ext. & Dome Lts. Z3 Flasher Unit - Nav. Lts.
TB12 Term. Blk Peal. Panel Edge Lts. Z5 XMSN Oil Temp. Bulb
TB13 Term. Blk. I n s t . P a n e l L t s . Z6 Engine Oil Temp. Bulb
TB14 Term. Blk. Inst. Panel Sec. Lts. Z8 Ice Interpreter
TB15 Term. Blk. C o c k p i t L t s L / H Z9 Fire Det. Cont.
TB16 Term. Blk. C o c k p i t L t s . R / H Z13 Ice Detector
TB25 Term. Blk. T h e r m o c o u p l e I n d . Z16 Fuel Qty. Tank Unit - Aft
T B26 Term. Blk. DC Gnd & Audio Z17 Displacement - Roll * Pitch Gyro
TB27 Term. Blk. A f t T h e r m o L e a d Z18 Rate Switching Gyro
TB29 Term. Blk. I n s t . G r o u n d Z22 Fuel Qty. Tank Unit R/H Fwd.
TB34 Term. Blk. Aft Dome Lt. Panel Z24 Hoist Control Box
TB35 Term. Blk. R / H F u e l C e l l Z25 Hoist Cable Cutter
TB36 Term. Blk. E x t . P o w e r D i o d e Z41 Hoist Control Pendant
TB38 Term. Blk. Left-hand Fuel Cell
TB39 Term. Blk. E l e c . C o m p t . A f t NOTES
TB45 Term. Blk. Pitot Heater - Disc.
TB60 Term. Blk. Battery Voltage, Fwd. A EFF 66-16868 thru 66-17144
TB61 Term. Blk. Battery Voltage, Aft
TB100 Term. Blk. Pilot and Copilot 5V Power Supply A EFF 66-746 through 66-16867
VR1 Regulator - Voltage (Main Gen)
A EFF 66-746 through 66-1210, 66-16000
VR2 Regulator, Voltage (Stby Gen.)
through 66-16033

F-15
TM 55-1520-210-23-3

Table F-3. Equipment List - Helicopters Serial No. 67-17146 Through 67-19537

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
Al Panel, DC Power El Detector Magnetic Chip
A2 Panel, AC Power E2 Detector Magnetic Chip
A3 Panel, Engine E3 Detector, Magnetic Chip
A4 Panel, Caution G2 Generator, 30VDC (300A)
A6 Panel, Instrument Lights G3 Generator, Tach (Gas Prod)
A7 Panel, Ext. Lights G4 Generator, Tach (Pwr Turb)
A8 Panel, Hydraulic Cont. G5 Generator, Tach (Rotor)
Al0 Panel, Miscellaneous G6 Generator, Starter 28V (200A)
All Panel, Heating HR1
A12 Cargo, Hook Assembly Heater, Pltot Tube
A13 Panel, Resistor I1 Indicator, Attitude (Copilot)
A14 Panel, AC Circuit Breaker I2 Indicator, Fuel Qty.
A15 Panel, Overhead Console I3 Indicator, Torque - Pilot
A20 Panel Assembly Aft Dome Lights I4 Indicator, Oil Press (Eng)
A21 Panel, Dome Lt. & Pitot Heater I5 Indicator, Oil Press (XMSN)
A26 Panel, Assembly Ext. Fuel I6 Indicator, Fuel Press.
I7 Indicator, Tach (Gas Prod)
B1 Syncro XMTR, Torque Press. I8 Indicator, Tach Dual (Pilot)
B2 Syncro XMTR, XMSN Oil Press. I9 Light, Utility (Pilot)
B3 Syncro XMTR, Engine Oil Press. I 10 Light, Dome
B4 Syncro XMTR, Fuel Press. Ill Light, Search
B5 Motor, Fuel Shutoff Valve I12 Light, Fire Warning
B6 Motor, R/H Fuel Boost Pump I13 Light, Master Caution
B7 Motor, Windshield Wiper I14 Light, Instr. Secondary
B8 Motor, R/H Aux. Fuel Pump I15 Lamp, lnstr. & Edge Lights
B12 Motor, Gov. RPM Actuator I16 Light, Landing
B13 Motor, L/H Aux. Fuel Pump I17 Light, Left Nav.
B22 Motor, Boom Actuator Hoist I18 Light, Right Nav.
B31 Motor, Copilot Windshield Wiper I19 Light, Tail
B35 Motor, Winch Assembly, Hoist I 20 Light, Top Fuselage
B34 Motor, Bleed Air Valve I21 Indicato, XMSN Oil Temp.
BT2 Battery I22 Indicator, Eng. Oil Temp.
I23 Indicator, Turn & Slip (Pilot)
Cl Capacitor, PF Corr. (MIL-C-25) I25 Light, XMSN Sump Inspect
C7 Capacitor Filter, JN14 I26 Light, Bottom Fuselage
CB1 Circuit Breaker (5A) I28 Light, Utility (Copilot)
CB2 Circuit Breaker (1OA) I31 Indicator, Exh. Temp. (Pilot)
CB3 Circuit Breaker (15A) I34 Standby Compass (Pilot)
CB4 Circuit Breaker (20A) I 40 Light, Anti- Collision
CB5 Circuit Breaker (25A) I42 Indicator, Attitude (Pilot)
CB6 Circuit Breaker (1A) I 44 Light, Cargo Release Armed
CB7 Circuit Breaker (35A) I45 Light, Hi-Lo RPM Warn.
CB8 Circuit Breaker (2A) J2 Recept. Pitot Tube Heater
CB11 Circuit Breaker (7.5A) J3 Recept. Instrument Panel Disc.
CB12 Circuit Breaker (50A) J4 Recept. Fuel Quantity Ind.
CB13 Circuit Breaker (1A) J5 Recept. Fuel Press. Ind.
CP1 Coupler, Fuel Qty. Unshielded J6 Copilot Att. Ind.
c P2 Coupler, Fuel Qty. Shielded J7 Recept. Engine Oil Temp. Ind.
CR2 Diode, Ext. Power Relay J8 Recept. Engine Oil Press. Ind.
CR30 Diode, Battery Voltage Fwd. LOC J9 Recept. Pilot Dual Tach. Rotor
CR31 Diode, Battery Voltage, Aft Loc J10 Recept. Pilot Dual Tach. Pwr. Turb.
J11 Recept. XMSN Oil Temp. Ind.
D1 Inverter (Main) J12 Recept. XMSN Oil Press. lnd.
D2 Inverter (Spare) J13 Recept. Pilot 5V Power Supply
DS1 Control Assembly RPM Warn. J14 Recept. Copilot 5V Power Supply

F-16
TM 55-1520-210-23-3

Table F-3. Equipment List - Helicopters Serial No. 67-17145 Through 67-19637 (Cont)

ITEM ITEM
NO. DESCRIPTION DESCRIPTION

K66 Relay, Battery Feeder


L1 Solenoid, Primer (Ignition) P47 Plug, Fuel Tank Disc. R/H Cell
L2 Solenoid, Fuel Cont. Valve P48 Plug, Fuel Tank Disc. R/H Cell
L4 Solenoid, Hydraulic Bypass P53 Plug, Unshld Tank Unit - Aft Cell
146 Solenoid, Hot-Air De-Ice P54 Plug, Shld Tank Unit - Aft Cell
L? Solenoid, Idle Stop Rel. P55 Plug, Fuel Tank Disc - Aft Cell
L8 Msg. Brake - Anti-Torque Force Trim P56 Plug, Fuel Tank Disc - Aft Cell
L9 Msg. Brake - Fore & Aft Force Trim P57 Plug, Ext. Fuel Cont. Panel
L10 Msg. Brake - Lat. Force Trim P60 Plug, Field Relay Gen.
L14 Solenoid, Door Post Aft Outlet Valve P64 Plug, Torque Press. XMTR
L15 Solenoid, Aft Outlet Valve Act. P65 Plug, Engine Oil Press. XMTR
L21 Solenoid, Var. Mix Valve P66 Plug, Fuel Press. XMTR
Ml Meter, DC Load (St-by Gen.) P68 Plug, Muff Heater Disc.
M2 Meter, DC Volts P71 Plug, Fuel Valve Shut- off
M3 Meter, AC Volts P72 Plug, Eng. Oil Press. Sw.
M4 Meter, DC Load (Main Gen.) P74 Plug, Battery Disc. Fwd.
02 Guard-Gen. Sw. - DC Pwr. Panel P75 Plug, Nav. Lts. Flasher
03 Guard-Cable Cut Sw. - Hyd Panel P77 Plug, Ice Detector
P 80 Plug, Eng. Air Filter Press. Sw.
P2 Plug, Pltot Tube Htr. P81 Plug* Starter Deck
P3 Plug, Inst. Panel Corm. P 84 P lug, De-icing Hot Air Valve
P4 Plug, Fuel Qty. Ind. P85 Plug, Oil Temp. Bulb
P5 Plug, Fuel Press. Ind. P 86 Plug, Pwr. Turb. Tach.
P6 Plug, copilot Att. Ind. P87 Plug, Gas Prod. Tach.
P7 Plug, Eng. Oil Temp. Ind. P88 Plug, Ignition Unit - Engine
P8 Plug, Eng. Oil Press. Ind. P89 Plug, Ignition Sol. Valve
P9 Plug, Pilot Dual Tach. (Rotor) P 90 Plug, Fuel Cont. Sol. Valve
Pl0 P lug, Pilot Dual Tach. (Pwr Turb.) P91 Plug, Engine Disc.
P11 Plug, XMSN Oil Temp. Ind. P92 Plug, Engine Forward Disc.
P12 Plug, XMSN Oil Press. Ind. P93 Plug, Fire Det. Forward Disc.
P13 Plug, Pilot 5V Power Supply P94 Plug, Fire Det. Element R/H
P14 Plug,
— Copilot 5V power Supply P95 Plug, Fire Det. Element L/H
P15 Plug, Pilot Torque Meter P 96 Plug, Fire Det. Element R/H
P16 Plug, Pilot Turn & Slip Ind. P97 Plug, Fire Det. Element L/H
P17 Plug, Gas Prod. Turb. Tach. P98 Plug, Tail Light Disc.
P20 Plug, Pilot’s Cyclic Stick P99A Plug, Thermocouple Disc. Engine
P21 Plug, Hydraulic Cont. Panel P99B Plug, Thermocouple Disc. Engine
P22 Plug, Copilot Cyclic Stick P102 Plug, Standby Compass (Pilot)
P23 Plug, Engine Panel P107 Plug, Copilot Coil. Stick
P24 Plug, Caution Panel P108 Plug, Fuel Diff. Press. Sw.
P25 Plug, Pilot Coil. Stick P110 Plug, Anti-Coil. Lt. Disc.
P26 Plug, Windshield Wiper Pill Plug, Anti- Coil. Lt.
P28 Plug, Hyd. Bypass Solenoid Valve P112 Plug, Msg. Brake Anti-Torque
P29 Plug, Hyd. Press. Warning Sw. P113 Plug, Msg. Brake Fore & Aft
P31 Plug, Cargo Hook P114 Plug, Msg. Brake - Lat.
P32 Plug, Cargo Hook Disc. P119 Plug, Cabin Roof Disc. Hoist
P35 Plug, Rotor Tach. Gen. P127 Plug, Var. Mix Valve Disc.
P36 Plug, XMSN Oil Press. Sw. P129 Plug, Displacement, Roll & Pitch Gyro
P37 Plug, XMSN Oil Temp. Bulb P130 Plug, Rate Switching Gyro
P38 Plug, Copilot W/S Wiper P131 Plug, Attitude Ind.
P39 Plug, XMSN Oil Press. XMTR P135 Plug, Ice Interpreter
P41 Plug, XMSN Disc. P136 Plug, Ice Interpreter
P42 Plug, Shielded Tank Unit Disc (R/H Tank) P138 Plug, Door Post - Aft-Out Val. Act.
P43 Plug, Monitor Tank Unit Disc (R/H Tank) P146 Plug, Bleed Air Valve
P44 Plug, Unshielded Tank Unit Disc (R/H Tank) P147 Plug, Unshld-Tank Coupler Disc.
P46 Plug, Fuel Tank Disc R/H Cell

F-18
TM 55-1520-210-23-3

Table F-3. Equipment List - Helicopters Serial No. 67-17145 Through 67-19637 (Cont)

ITEM ITEM
NO. DESCRIPTION DESCRIPTION

K66 Relay, Battery Feeder


L1 Solenoid, Primer (Ignition) P47 Plug, Fuel Tank Disc. R/H Cell
L2 Solenoid, Fuel Cont. Valve P48 Plug, Fuel Tank Disc. R/H Cell
L4 Solenoid, Hydraulic Bypass P53 Plug, Unshld Tank Unit - Aft Cell
146 Solenoid, Hot-Air De-Ice P54 Plug, Shld Tank Unit - Aft Cell
L? Solenoid, Idle Stop Rel. P55 Plug, Fuel Tank Disc - Aft Cell
L8 Msg. Brake - Anti-Torque Force Trim P56 Plug, Fuel Tank Disc - Aft Cell
L9 Msg. Brake - Fore & Aft Force Trim P57 Plug, Ext. Fuel Cont. Panel
L10 Msg. Brake - Lat. Force Trim P60 Plug, Field Relay Gen.
L14 Solenoid, Door Post Aft Outlet Valve P64 Plug, Torque Press. XMTR
L15 Solenoid, Aft Outlet Valve Act. P65 Plug, Engine Oil Press. XMTR
L21 Solenoid, Var. Mix Valve P66 Plug, Fuel Press. XMTR
Ml Meter, DC Load (St-by Gen.) P68 Plug, Muff Heater Disc.
M2 Meter, DC Volts P71 Plug, Fuel Valve Shut- off
M3 Meter, AC Volts P72 Plug, Eng. Oil Press. Sw.
M4 Meter, DC Load (Main Gen.) P74 Plug, Battery Disc. Fwd.
02 Guard-Gen. Sw. - DC Pwr. Panel P75 Plug, Nav. Lts. Flasher
03 Guard-Cable Cut Sw. - Hyd Panel P77 Plug, Ice Detector
P 80 Plug, Eng. Air Filter Press. Sw.
P2 Plug, Pltot Tube Htr. P81 Plug* Starter Deck
P3 Plug, Inst. Panel Corm. P 84 P lug, De-icing Hot Air Valve
P4 Plug, Fuel Qty. Ind. P85 Plug, Oil Temp. Bulb
P5 Plug, Fuel Press. Ind. P 86 Plug, Pwr. Turb. Tach.
P6 Plug, copilot Att. Ind. P87 Plug, Gas Prod. Tach.
P? Plug, Eng. Oil Temp. Ind. P88 Plug, Ignition Unit - Engine
P8 Plug, Eng. Oil Press. Ind. P89 Plug, Ignition Sol. Valve
P9 Plug, Pilot Dual Tach. (Rotor) P 90 Plug, Fuel Cont. Sol. Valve
Pl0 P lug, Pilot Dual Tach. (Pwr Turb.) P91 Plug, Engine Disc.
P11 Plug, XMSN Oil Temp. Ind. P92 Plug, Engine Forward Disc.
P12 Plug, XMSN Oil Press. Ind. P93 Plug, Fire Det. Forward Disc.
P13 Plug, Pilot 5V Power Supply P94 Plug, Fire Det. Element R/H
P14 Plug,
— Copilot 5V power Supply P95 Plug, Fire Det. Element L/H
P15 Plug, Pilot Torque Meter P 96 Plug, Fire Det. Element R/H
P16 Plug, Pilot Turn & Slip Ind. P97 Plug, Fire Det. Element L/H
P17 Plug, Gas Prod. Turb. Tach. P98 Plug, Tail Light Disc.
P20 Plug, Pilot’s Cyclic Stick P99A Plug, Thermocouple Disc. Engine
P21 Plug, Hydraulic Cont. Panel P99B Plug, Thermocouple Disc. Engine
P22 Plug, Copilot Cyclic Stick P102 Plug, Standby Compass (Pilot)
P23 Plug, Engine Panel P107 Plug, Copilot Coil. Stick
P24 Plug, Caution Panel P108 Plug, Fuel Diff. Press. Sw.
P25 Plug, Pilot Coil. Stick P110 Plug, Anti-Coil. Lt. Disc.
P26 Plug, Windshield Wiper Pill Plug, Anti- Coil. Lt.
P28 Plug, Hyd. Bypass Solenoid Valve P112 Plug, Msg. Brake Anti-Torque
P29 Plug, Hyd. Press. Warning Sw. P113 Plug, Msg. Brake Fore & Aft
P31 Plug, Cargo Hook P114 Plug, Msg. Brake - Lat.
P32 Plug, Cargo Hook Disc. P119 Plug, Cabin Roof Disc. Hoist
P35 Plug, Rotor Tach. Gen. P127 Plug, Var. Mix Valve Disc.
P36 Plug, XMSN Oil Press. Sw. P129 Plug, Displacement, Roll & Pitch Gyro
P37 Plug, XMSN Oil Temp. Bulb P130 Plug, Rate Switching Gyro
P38 Plug, Copilot W/S Wiper P131 Plug, Attitude Ind.
P39 Plug, XMSN Oil Press. XMTR P135 Plug, Ice Interpreter
P41 Plug, XMSN Disc. P136 Plug, Ice Interpreter
P42 Plug, Shielded Tank Unit Disc (R/H Tank) P138 Plug, Door Post - Aft-Out Val. Act.
P43 Plug, Monitor Tank Unit Disc (R/H Tank) P146 Plug, Bleed Air Valve
P44 Plug, Unshielded Tank Unit Disc (R/H Tank) P147 Plug, Unshld-Tank Coupler Disc.
P46 Plug, Fuel Tank Disc R/H Cell

F-18
TM 55-1520-210-23-3

Table F-3. Equipment List - Helicopters Serial No. 67-17145 Through 67-19537 (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
P148 Plug, Unshld-Tank Coupler Disc.
P149 Plug, Unshld-Tank Coupler Disc. S27 Switch, Hyd. Press.
P151 Plug, Shld-Tank Coupler Disc. S28 Switch , XMSN Oil Press. Warning
P152 Plug, Shld-Tank Coupler Disc. S29 Switch, Eng. Oil Press. Warning
P153 Plug, Shld-Tank Coupler DISC. S31 Switch, Limit (Ext. Pwr. Door)
P155 Plug, Hi-Lo RPM Warning S32 Switch, Cargo Release (Pit)
P156 Plug, Eng. Fuel Filter Bypass S33 Switch, Gov. (Auto- Emer)
P166 Plug, Aft Outlet Valve S39 Switch, Invtr. (Main-Spare)
P191 Plug, Inverter Disc. - Main S36 Switch, Cargo Release
P192 Plug, Inverter Disc. - Spare S37 Switch, RPM Gov. (Pit)
P194 Plug, Engine Chip Detector S38 Switch, Fuel (ON-OFF)
P267 Plug, Battery Disc. Aft S40 Switch, Battery (ON-OFF)
P268 Plug, Hoist to Ship S41 Switch, Upper Float
P269 Plug, Cable Cut & Slip Limit S42 Switch, Lower Float
P270 Plug, Hoist to Cont. Pendant S44 Switch, Fuel - Low Level
P271 Plug, Boom Act. S45 Switch, Fuel - Transfer L/H
P272 Plug, Hoist to Winch Assy. S46 Switch, Fuel - Transfer R/H
P273 Plug, Cont. Pendant S47 Switch, ICS Sw. Pilot's Cyclic Stick
P274 Plug, Boom Act. S48 Switch, KS SW Copilot's Cyclic Stick
P275 Plug, Winch Assy S50 Switch, Idle Stop Rel (Pit)
P1017 S51 Switch, RPM Gov. (Copilot)
Plug, Ext. Fuel Disc. L/H S58 Switch, Fuel Diff. Press.
P1024 Plug, Ext. Fuel Disc. R/H
PS1 Pilot 5V Power Supply (PS-274B) S59 Switch, Anti-Coil. Lt.
PS2 Copilot 5V Power Supply (PS-274B) S62 Switch, Non- Ess Bus Cont.
S63 Switch, Ext. Fuel Jett.
R1 Shunt-Ammeter (Stby Gen.) S68 Switch j Force Trim
R2 Shunt-Ammeter (Main Gen.) S70 Switch, Starter-Gen.
R3 Resistor-Windshield Wiper S73 Switch, Overheat Bleed Air
R4 Rheostat, Plt Inst. Lt. Dim S77 Switch, Searchlight (ON-STOW)
R5 Rheostat, Sec. Inst. Lt. Dim S76 Switch, Landing Lt. (ON-OFF)
R6 Rheostat, Overhead Console S77 Switch, Starter (Copilot Coil)
R7 Resistor, Nav. Lts. Dim S78 Switch, Cargo Rel (Copilot)
R8 Rheostat, Peal. Lts. Dim S79 Switch, Fuel Ejector Flow Sw. L/H
R9 Rheostat, Eng. Inst. Lts. Dim S 80 Switch, Fuel Ejector Flow Sw. R/H
R10 Rheostat, Copilot Inst. Lts. Dim S81 Switch, De-Ice (ON-OFF)
R11 Resistor, Fire Det. Cont. S83 Switch, Bleed Air (ON-OFF)
R12 Resistor, Spool Thermocouple S85 Switch, Aft Outlets (Htr)
R21 Rheostat, Aft Dome Lts. S87 Switch, Aft-Outlet, Limit
R26 Rheostat, Course Ind. Lt. Dim S93 Switch, Hi- Lo RPM
R27 Resistor, AC Load Balancing S94 Switch, Fuel Filter Bypass
S1 Switch, Aft Dome Lt. S 96 Switch, Cable Cut
S2 Switch, Rotary (DC VM Sel) S97 Switch, Cable Up Limit
S4 Switch, XMSN Sump Insp. Lt. S101 Switch, Overload Sense
S5 Switch, Fuel Qty Test Sill Switch, Fuel Trans. Pump
S6 Switch, Starter (Pit Coil) S112 Switch, Pilot Hoist Cont.
S7 Switch, Hyd Boost Cont. S114 Switch, Fire Control
S8 Switch, Gen. (On-Off Reset) S115 Switch, Fire Control
S9 Switch, Pitot Heater S124 Switch, Sel - W/Wiper
Sl0 Switch, Force Trim (Copilot Sw.) S134 Switch, Chip Det. Sel.
S12 Switch, Searchlight Cont. S195 Switch, Diff. Press.
S13 Switch, Nav. Lts. (Flash Steady)
S14 Switch, Nav. Lts. (Bright-Dim) T1 Transformer 115/28V
S.8 Switch, Force Trim (Pit- Cyl) TB1 Term. Blk. Fwd. Inst. Panel
S20 Switch, Test (Fire Det.) T B2 Term. Blk. Overhead Console R/H
S23 Switch, Windshield Wiper T B3 Term. Blk. Overhead Console L/H
S25 Switch, Landing Lt. (Ext-Retr) T B4 Term. Blk. Aft Fuel Cell
S26 Switch, XMSN Oil Temp. TB99 Term. Blk. Top Ext. & Dome Lts.

F-19
TM 55-1520-210-23-3

Table F-4. Equipment List - Helicopters Serial No. 68-15214 and Subsequent (Cont)

ITEM ITEM
NO. DESCRIPTION No. DESCRIPTION

TB12 Term. Blk. Peal. Panel Edge Lts. VR1 Regulator - Voltage (Main Gen)
TB13 Term. Blk. Inst. Panel Lts. VR2 Regulator - Voltage (Stby Gen)
TB14 Term. Blk. Inst. Panel Sec. Lts.
TB15 Term. Blk. Cockpit Lts. L/H W1 Cable Assembly - Fire Det.
TB16 Term. Blk. Cockpit Lts. R/H
TB22 Term. Blk. Copilot Headset Z2 Engine, Ignition Unit
TB23 Term. Blk. Pilot Headset_ Z3 Flasher Unit - Nav. Lts.
TB25 Term. Blk. Thermocouple Ind. Z5 XMSN Oil Temp. Bulb
TB26 Term. Blk. DC Grid. & Audio Z6 Engine Oil Temp. Bulb
TB27 Term. Blk. Aft Thermo Lead Z8 Ice Interpreter
TB29 Term. Blk. Inst. Ground Z9 Fire Det. Cont.
TB34 Term. Blk. Aft Dome Lt. Panel Z13 Ice Detector
TB35 Term. Blk. R/H Fuel Cell Z16 Fuel Qty. Tank Unit - Aft
TB36 Term. Blk. Ext. Power Diode Z17 Displacement - Roll & Pitch Gyro
TB38 Term. Blk. L/H Fuel Cell Z18 Rate Switching Gyro
TB39 Term. Blk. Elect. Compt. Aft Z22 Fuel Qty. Tank Unit R/H Fwd.
TB45 Term. Blk. Pitot Htr. - Disc. Z24 Hoist Control Box
TB60 Term. Blk. Battery Voltage, Fwd. Z25 Hoist Cable Cutter
TB61 Term. Blk. Battery Voltage, Aft Z41 Hoist Control Pendant
TB100 Term, Blk. Pilot and Copilot 5V Power Supply

F-20
TM 55-1520-210-23-3

Table F-4. Equipment List - Helicopters Serial No. 68-16214 and Subsequent

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
Al Panel, DC Power E3 Detector, Magnetic Chip
A2 Panel, AC Power E4 Detector, Magnetic Chip
A3 Panel, Engine
A4 Panel, Caution G2 Generator, 30 VDC (300A)
A6 Panel, Inst. Lights G3 Generator, Tach (Gas Prod)
A7 Panel, Ext. Lights G4 Generator, Tach (Pwr Turb)
A8 Panel, Hydraulic Control G5 Generator, Tach (Rotor)
A1O Panel, Miscellaneous G6 Generator, Starter 28 V (200A)
All Panel, Heating
A12 Cargo Hook Assy HR1 Heater, Pitot Tube
A13 Panel, Resistor
A14 Panel, AC Circuit Breaker I1 Indicator, Attitude (Copilot)
A15 Panel, Overhead Console I2 Indicator, Fuel Qty
A20 Panel Assy, Aft Dome Lts I3 Indicator, Torque - Pilot
A21 Panel, Dome Lt & Pitot Htr I4 Indicator, Oil Press (Eng)
A26 Panel Assy, Ext. Fuel I5 Indicator, Oil Press (XMSN)
I6 Indicator, Fuel Press
B1 Syncro XMTR, Torque Press I7 Indicator, Tach (Gas Prod)
B2 Syncro XMTR, XMSN Oil Press I8 Indicator, Tach-Dual
B3 Syncro, XMTR Engine Oil Press I9 Light, Utility (Pilot)
B4 Syncro XMTR, Fuel Press I10 Light, Dome
B5 Motor, Fuel Shut-Off Valve I1l Light, Search
B6 Motor, R/H Fuel Boost Pump I12 Light, Fire Warning
B7 Motor, Windshield Wiper I13 Light, Master Caution
B8 Motor, R/H Aux. Fuel Pump I14 Light, Instr, Secondary
B12 Motor, Gov RPM Actuator II5 Lamp, Instr & Edge Lights
B13 Motor, L/H Aux. Fuel Pump I16 Light, Landing
B31 Motor, Copilot Windshield Wiper I17 Light, Left Nav.
B34 Motor, Bleed Air Valve I18 Light, Right Nav.
BT2 Battery I19 Light, Tail
I20 Light, Top Fuselage
Cl Capacitor, PF Corr. (MIL-C-25) I21 Indicator, XMSN Oil Temp
C7 Capacitor, Filter, JN14 I22 Indicator, Eng. Oil Temp.
CB1 Circuit Breaker (5A) I23 Indicator, Turn & Slip (Pit)
C B2 Circuit Breaker (1OA) I25 Light, XMSN Sump Inspect
CB3 Circuit Breaker (15A) I26 Light, Bottom Fuselage
CB4 Circuit Breaker (20A) I28 Light, Utility (Copilot)
CB5 Circuit Breaker (25A) I31 Indicator, Exh. Temp (Pit)
CB6 Circuit Breaker (1A) I34 Standby Compass (Pit)
CB7 Circuit Breaker (35A) I40 Light, Anti- Collision
CB8 Circuit Breaker (2A) I42 Indicator, Attitude (Pit)
CB11 Circuit Breaker (7.5A) I44 Light, Cargo Release Armed
CB12 Circuit Breaker (50A) I 45 Light, Hi-Lo RPM Warn.
CB13 Circuit Breaker (1A) I46 Light, Utility - Crew Pos 1
CP1 Coupler, Fuel Qty. Unshielded I47 Light, Utility - Crew Pos 2
CP2 Coupler, Fuel Qty. Shielded I48 Light, Utility - Crew Pos 3
CR2 Diode, Ext. Pwr. Relay
CR30 Diode, Batt. Voltage Fwd Loc
CR31 Diode, Batt. Voltage Aft Loc
D1 Inverter, 250V.A. 3 Ph (Main)
D2 Inverter, 250V.A. 3 Ph (Spare)
DS1 Control Assy, RPM Warn.
El Detector, Magnetic Chip
E2 Detector, Magnetic Chip

F-20.1/(F-20.2 blank)
TM 55-1520-210-23-3

Table F-4. Equipment List - Helicopters Serial No. 68-15214 and Subsequent (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

J2 Recept. Pitot Tube Htr


J3 Recept. Instr. Panel Disc.
J4 Recept. Fuel Qty Ind.
J5 Recept. Fuel Press Ind.
J6 Recept. Copilot Att. Ind.
J7 Recept. Eng. Oil Temp. Ind.
J8 Recept. Eng. Oil Press. Ind.
J9 Recept. Pilot Dual Tach Rotor
J10 Recept. Pilot Dual Tach Pwr Turb.
J11 Recept. XMSN Oil Temp. Ind.
J12 Recept. XMSN 011 Press. Ind.
J13 Recept. Pilot 5V Power Supply
J14 Recept. Copilot 5V Power Supply
J15 Recept. Pilot Torque Meter

F-21
TM 55-1520-210-23-3

Table F-4 Equipment List - Helicopters Serial No. 68-15214 and Subsequent (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
J16 Recept. Pilot Turn & Slip Ind. J107 Recept. Copilot Coil. Stick
J17 Recept. Gas Prod. Tach. J108 Recept. Fuel Diff. Press. Sw.
J20 Recept. Pilot Cyclic Stick J109 Recept. Ext. Power
J21 Recept. Hydraulic Cont. Panel J110 Recept. Anti-Coil. Lt. Disc.
J22 Recept. Copilot Cyclic Stick J11 Recept. Anti-Coil. Lt.
J23 Recept. Engine Panel J112 Recept. Msg. Brake Anti-Torque
J24 Recept. Caution Panel J113 Recept. Msg. Brake Fore & Aft
J25 Recept. Pilot Coil. Stick J114 Recept. Msg. Brake Lat
J26 Recept. Windshield Wiper J115 Recept. Test- Eng. Vibration Meter
J28 Recept. Hyd. Bypass Solenoid J127 Recept. Var. Mix Valve Disc.
J29 Recept. Hyd. Press. Warn. Sw. J129 Recept. Displacement-Roll & Pitch Gyro
J31 Recept. Cargo Hook J130 Recept. Rate Switching Gyro
J32 Recept, Cargo Slind Disc. J131 Recept. Attitude Ind.
J35 Recept. Rotor, Tach. Gen. J135 Recept. Ice Interpreter
J36 Recept, XMSN Oil Press. Sw. J136 Recept. Ice Interpreter
J37 Recept. XMSN Oil Temp. Bulb J138 Recept. Door Post Outlet Valve Act
J38 Recept. Copilot Windshield Wiper J146 Recept. Bleed Air Valve
J39 Recept. XMSN Oil Press. XMTR J147 Recept. Internal Aux. Fuel Disc L/H
J41 Recept. XMSN Disc. J148 Recept. Internal Aux. Fuel Disc R/H
J42 Recept. Fuel Tank Disc R/H J155 Recept. Hi-Lo RPM Warn.
J43 Recept. Compensator Fuel Tank Disc R/H J156 Recept. Eng. Fuel Filter Bypass Sw.
J44 Recept. Fuel Tank Disc R/H J166 Recept. Aft, Outlet Valve
J53 Recept. Bulkhead Feed-thru-aft Fuel Cell J191 Recept. Main Inverter Pwr.
J54 Recept. Bulkhead Feed- thru- aft Fuel Cell J192 Recept. Spare Inverter Pwr.
J57 Recept. Ext. Fuel Cont. Panel J194 Recept. Engine Chip Detector
J60 Recept. Socket, Relay-Gen. Field J267 Recept. Battery Disc. Aft
J64 Recept. Torque Press. XMTR J1017 Recept. Ext. Fuel Disc. L/H
J65 Recept. Eng. Oil Press. XMTR J1024 Recept. Ext. Fuel Disc. R/H
J66 Recept. Fuel Press. XMTR
J68 Recept. Disc. Muff Heater K1 Relay, Ext. Pwr.
J71 Recept. Eng. Fuel Valve K2 Relay, Non- Ess Bus
J72 Recept. Eng. Oil Press. Sw. K3 Relay, Starter
J74 Recept. Batt. Disc. Fwd. K4 Relay, Bus Cont. (Gen Fail)
J75 Recept. Nav. Lts. Flasher K5 Relay, Reverse Curr. (Main)
J77 Recept. Ice Detector K6 Relay, Overvoltage
J80 Recept. Eng. Air Filter Press. Sw. K7 Relay, Gen. Field
J81 Recept. Starter Deck K8 Relay, AC Failure
J 84 Recept. De-Icing Hot Air Valve K9 Relay, Battery
J85 Recept. Eng. Oil Temp. Bulb K10 Relay, Fuel Transfer
J 86 Recept. Pwr. Turb. Tach. K15 Relay, Standby Gen. Field
J87 Recept. Gas Turb. Tach. K23 Relay, Standby Gen. Rev. Curr.
J88 Recept. Ignition Unit, Eng. K24 Relay, Cargo Hook Release
J89 Recept. Primer Valve (Fuel Ign. Sol.) K27 Relay, Inverter
J 90 Recept. Fuel Cont. Sol. Valve K35 Relay, Main Invtr. Pwr;
J91 Recept. Engine Disc. K36 Relay, Spare Invtr. Pwr.
J92 Recept. Engine Fwd. Disc. K37 Relay, Lo- Fuel Caution Lt.
J93 Recept. Fire Det. Fwd. Disc. K28 Relay, Lo- Fuel Caution Lt.
J94 Recept. Fire Det. Element R/H K46 Relay, Overheat
J95 Recept. Fire Det. Element L/H K65 Relay, Battery, Aft Loc
J96 Recept. Fire Det. Element R/H K66 Relay, Battery Feeder
J97 Recept. Fire Det. Element L/H
J98 Recept. Tail Lt. Disc. L1 Solenoid, Primer (Ignition)
J99 Recept. Thermocouple Disc. L2 Solenoid, Fuel Cont. Valve
J102 Recept. Standby Compass (Pit) L4 Solenoid, Hyd. Bypass
J105 Recept. Heated Blanket L/H L6 Solenoid, Hot-Air De-icer
J106 Recept. Heated Blanket R/H L7 Solenoid, Idle Stop Rel.
TM 55-1520-210-23-3

Table F-4. Equipment Liat - Helicopters Serial No. 68-15214 and Subsequent (Cont)
ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
L8 Msg. Brake - Anti-Torque Force Trim P64
L9 Msg. Brake - F & A Force Trim Plug, Torque Press. XMTR
L10 Msg. Brake - Lat Force Trim P65 Plug, Eng. Oil Press. XMTR
L14 Solenoid, Door Post Htr. Outlet Valve P66 Plug, Fuel Press XMTR
L15 Solenoid, Aft Outlet Valve Act. P68 Plug, Muff Heater Disc.
L21 Solenoid, Var. Mix Valve P71 Plug, Fuel Valve Shut-Off
P72 Plug, Eng. Oil Press Sw.
Ml Meter, DC Load (Stand-by-gen.) P74 Plug, Battery Disc. Fwd.
M2 Meter, PC Volts P75 Plug, Nav. Lts. Flasher
M3 Meter, AC Volts P77 Plug, Ice Detector
M4 Meter, DC Load (Main Gen) P80 Plug, Eng. Air Filter Press. Sw.
02 Guard - Gen. Sw. DC Pwr. Panel P81 Plug, Starter Deck
P2 Plug, Pitot Tube Heater P84 Plug, De-Icing Hot Air Valve
P3 Plug, Inst. Panel Corm. P85 Plug, Oil Temp. Bulb
P4 Plug, Fuel Qty Ind. P 86 Plug, Pwr. Turb. Tach.
P5 Plug, Fuel Press Ind. P87 Plug, Gas Prod. Tach.
P6 Plug, Copilot Att. Ind. P88 Plug, Ignition Unit- Eng.
P7 Plug, Engine Oil Temp. Ind. P89 Plug, Ignition Sol. Valve
P8 Plug, Engine Oil Press. Ind. P90 Plug, Fuel Cont. Sol Valve
P9 Plug, Pilot Dual Tach. Rotor P91 Plug, Engine Disc.
P10 Plug, Pilot Dual Tach. (Pwr. Turb.) P92 Plug, Engine Fwd. Disc.
P11 Plug, XMSN Oil Temp. Ind. P93 Plug, Fire Det. Fwd, Disc.
P12 Plug, XMSN Oil Press. Ind. P94 Plug, Fire Det. Element R/H
P13 Plug, Pilot 5v Power Supply P95 Plug, Fire Det. Element L/H
P14 Plug, Copilot 5V Power Supply P96 Plug, Fire Dec. Element R/H
P15 Plug, Pilot Torque Meter P97 Plug, Fire Det. Element L/H
P16 Plug, Pilot Turn & Slip Ind. P98 Plug, Tail Lt. Disc.
P17 Plug, Gas Prod. Turb. Tach. P99A Plug, Thermocouple Disc - Eng.
P20 Plug, Pilot’s Cyclic Stick P99B Plug, Thermocouple Disc - Eng.
P21 Plug, Hyd. Cont. Panel P102 Plug, Standby Compass (Pilot)
P22 Plug, Copilot Cyclic Stick P107 Plug, Copilot Coil. Stick
P23 Plug, Engine Panel P108 Plug, Fuel Diff. Press. Sw.
P24 Plug, Caution Panel P110 Plug, Anti- Coil. Lt. Disc.
P25 Plug, Pilot Coil. Stick Pill Plug, Anti- Coil. Lt.
P26 Plug, Windshield Wiper P112 Plug, Msg. Brake Anti- Torque
P28 Plug, Hyd. Bypass Sol. Valve P113 Plug, Msg. Brake F & A
P29 Plug, Hyd. Press. Warn. Sw. P114 Plug, Msg. Brake - Lat.
P31 Plug, Cargo Hook P127 Plug, Var. Mix Valve Disc.
P32 Plug, Cargo Hook Disc. P129 Plug, Displacement, Roll & Pitch Gyro
P35 Plug, Rotor Tach. Gen. P130 Plug, Rate Switching Gyro
P36 Plug, XMSN Oil Press. Sw. P131 Plug, Attitude Ind.
P37 Plug, XMSN Oil Temp. Bulb P135 Plug, Ice Interpreter
P38 Plug, Copilot Windshield Wiper P136 Plug, Ice Interpreter
P39 Plug, XMSN Oil Press. XMTR P138 Plug, Door Post-Aft Outlet Valve Act.
P41 Plug, XMSN Disc. P146 Plug, Bleed Air Valve
P 42 Plug, Shielded Tank Unit Disc(R/H Tank) P147 Plug, Unshielded Tank Coupler Disc.
P43 Plug, Monitor Tank Unit Disc(R/H Tank) P148 Plug, Unshielded Tank Coupler Disc.
P44 Plug, Unshielded Tank Unit Disc(R/H Tank) P149 Plug, Unshielded Tank Coupler Disc.
P46 Plug, Fuel Tank Disc. R/H Cell P151 Plug, Shielded Tank Coupler Disc.
P47 Plug, Fuel Tank Disc R/H Cell P152 Plug, Shielded Tank Coupler Disc.
P48 Plug, Fuel Tank Disc R/H Cell P153 Plug, Shielded Tank Coupler Disc.
P53 Plug, Unshielded Tank Unit-Aft Cell P155 Plug, Hi- Lo RPM Warning
P54 Plug, Shielded Tank Unit-Aft Cell P156 Plug, Eng. Fuel Filter Bypass
P55 Plug, Fuel Tank Disc - Aft Cell P166 Plug, Aft Outlet Valve
P56 Plug, Fuel Tank Disc - Aft Cell P191 Plug, Inverter Disc. - Main
P57 Plug, Ext. Fuel Cont. Panel P192 Plug, Inverter Disc. - Spare
P60 Plug, Field Relay Generator P194 Plug, Eng. Chip Detector

F-23
TM 55-1520-210-23-3

Table F-4. Equipment List - Helicopters Serial No. 68-16214 and Subsequent (Cont)

TEM ITEM
NO. DESCRIPTION NO. DESCRIPTION
..-
Z67 Plug, Battery Disc. Art S68 Switch, Fuel Diff Press
P1017 Plug, Ext. Fuel Disc. L/H
P1027 S59 Switch, Anti-Coll, Lt.
Plug, Ext. Fuel Disc. R/H S82 Switch, Non-Ess Bus Cont
‘s 1 Pilot 5V Power Supply S83 Switch, Ext. Fuel Jett
S2 Copilot 5V Power Supply S68 Switch, Force Trim
1131C Power Module S70 Switch, Starter-Gen.
R1 Shunt, Ammeter (Stby Gen) S73 Switch, Overheat Bleed Air
R2 Shunt Ammeter @la.in Gen) S75 Switch, Searchlight (ON-STOW)
R3 Resistor, Windshield Wiper S76 Switch Landing Lt. (ON-OFF)
R4 Rheostat, Pilot Inst. Lt. Dim S78 Switch, Cargo Rel. (Copilot)
R5 Rheostat, Sec. Instrument Lt. Dim Switch, Fuel Ejector Flow Sw. L/H
R6 Rheostat, Overhead Console S79
S80 Swithc, Fuel Ejector Flow Sw. R/H
R7 Resistor, Nav. Lts. Dim S81 Switch, De-ice (ON-OFF
R8 Rheostat Peal- Lts. Dim Switch, Bleed Air (ON-OFF)
Rheostat Eng Inst. Lts. Dim 983
R9 S85 Switch, Aft Outlists (Htr)
R10 Rheostat Copilot Inst. Lts. Dim
Resistor Fire Det. Cont S87 Switch, Aft-Outlet Limit
R11 Switch, Hi-Lo RPM
R12 Resistor Speel Thermocouple S93
Rheostat Aft Dome Lts. S94 Switch, Fuel Filter Bypass
R21 S1ll Switch, Fuel Trans. Pump
126 Rheostat Course Ind. Lt. Dim
Resistor AC Load Balancing S112 Switch, Pilot Hoist cont
R27 S114 Switch, Fire Control
S1 Switch, Aft Demo Lt. S116 Switch, Fire Control
S2 Switch Rotary (DC VM sel) S124 Switch, Sel-Windshield Wiper
34 Switch XMSN Sump Insp. Lt. S134 Switch, Chip Det. SeL
S5 Switch, Fuel Qty. Test S195 Switch, Diff. Press.
S6 Switch Starter (Plt Coll.)
37 Switch Hyd. Boost Cont T1 Transformer 116/28V
S8 switch Gen (on-off Reset TB1 Term. Blk. Fwd. Inst. Panel
S9 Switch Pitot Heater TB2 Term Blk Overhead Console R/H
910 Switch Force Trim (Copilot Cyc.) TBS Term. Blk Overhead console L/H
911 Switch, Rotary (AC VM sel) TB4 Term. BIk Ant Fuel Cell
912 Switch Searchlight Cont TB9 Term. Blk. Top Ext. & Demo Lts.
S13 Switch Nav. Lts. (Flash Steady) TB12 Term. Blk. Ped. Panel Edge Lts.
S14 Switch Nav. Lts. (Bright-Dim) TB13 Term. Blk Inst. Panel Lts.
918 Switch Force Trim (Pit-CyC) TB14 Term. Blk. Inst. Panel Sec Lts.
920 Switch Test (Fire Det) TBI5 Term. BW Cockpit Lts. L/H
S23 Switch Wlndshield Wiper TB16 Term. Blk Cockpit Lts. R/H
S26 Switch Landing (It. (Ext-Rotr TB25 Term. Blk Thermocouple Ind.
828 Swttch XMSN Oil Temp. TB26 Term. Blk. DC Gnd. & Audio
S27 Switch Hyd. Press TB27 Term. Blk. Aft Thermo Lead
S28 Switch XMSN Oil Press Warn. TB29 Term. Blk. Inst. Gnd.
S29 Switch Eng. 011 Press Warn TB34 Term. Blk. Aft Dome Lt. Panel
931 Switch, Limit Ext Pwr. Door) TB35 Term. Blk. R/H Fuel Cell
S32 Switch, Cargo Release (Plt.) TB36 Term. Blk. Ext. Pwr. Diode
S33 Switch, Gov. (Aut0-Emer) TB38 Term. Blk. L/H Fuel Call
936 Switch, cargo Release TB39 Term. Blk. Elect. Compt. Aft
S37 Switch, RPM Gov. (Pit) TB45 Term. Blk. Pitot Htr. - Disc.
838 Switch Fuel (ON-OFF) TB80 Term. Blk. Battery Voltage, Fwd.
939 Switch Invtr. (MiLin-spare) TB61 Term. Blk. Battery Voltage, Aft
S40 Switch Battery (ON-OFF) TB62 Term. Blk. Crew Pos 1 - -
S41 Switch Upper Float TB63 Term. Blk. Crew Pos 2
S42 Switch Lower Float TB64 Term. Blk. Crew Pos 3
S44 Switch, Fuel-Low Level TB100 Term. Blk. Pilot and Copilot 5V Power Supply
S45 Switch Fuel-Transfer L/H
S46 Switch Fuel-Transfer R/H
S50 Switch, Idle Stop Rel (Pit)
S51 Switch RPM Gov (Copilot)

F-24 Change 4
TM 55-1520-210-23-3

Table F-4. Equipment List - Helicopters Serial No. 68-15214 and Subsequent (Cont)

ITEM ITEM
NO. DESCRIPTION NO. DESCRIPTION

VR1 Regulator - Voltage (Main Gen)


VR2 Regulator - Voltage (Stby Gen)
WI Cable Assy. Fire Det.
Z2 Eng. Ignition Unit

218-261 0 - 88 -20
F-24.1/(F-24.2 blank)
TM 55-1520-210-23-3

Table F-5. Connector Replacement Chart

WIRE NO. RECEPTACLE PIN PLUG WIRE NO.

D9A20 J3 A P3 D9B20
X11A20 J3 B P3 X11B20
X12A20 J3 C P3 X12B20
D13B22 J3 D P3 D13A22
D12A22 J3 E P3 D12B22
D35A20 J3 F P3 D35B20
D34B20 J3 G P3 D34C20
L36A20 J3 H P3 L36B20
L20F20 J3 J P3 L20E20
W109A20 J3 R P3 W109B20
E32A20 J3 S P3 E32B20
W2B20 J3 T P3 W2A20
W4B20 J3 U P3 W4C20
M3F20 J3 V P3 M3G20
E7D18N J3 w P3 E7E18N
M1C20 J3 X P3 M1D20
W12A20 J3 Y P3 W12B20
W6A20 J3 Z P3 W6B20
L20A20 J3 a P3 L20B20
L19A20 J3 b P3 L19B20
L18A20 J3 c P3 L18B20

C12A20 J20 A P20 P/O Equipment


M4B20 J20 c P20 P/O Equipment
M3E20 J20 E P20 P/O Equipment
J20 G P20 P/O Equipment
J20 H P20 P/O Equipment
M29A20 J20 L P20 P/O Equipment
M27A20 J20 M P20 P/O Equipment
M30A20 J20 N P20 P/O Equipment
M22A20 J20 P P20 P/O Equipment
M28A20 J20 R P20 P/O Equipment
RZ1714B20 J20 S P20 P/O Equipment
RZ1853B20N J20 T P20 P/O Equipment
RZ1715C20 J20 U P20 P/O Equipment
C1C20 J20 V P20 P/O Equipment

M43C20 J21 A P21 M25A20


J21 B P21
J21 C P21
L21C20 J21 D P21 L21B20
C8B20 J21 E P21 C8A20
C9A20 J21 F P21 C9B20
L22E20N J21 G P21 L22D20N
W18B20 J21 H P21 W18A20
W17A20 J21 I P21 W17B20
M44A20 J21 J P21 M26A20
W19C20 J21 K P21 W19B20
C12B20 J21 L P21 C12A20
C21A20 J21 M P21 C21B20
J21 N P21

M4C20 J22 A P22 P/O Equipment


J22 B P22 P/O Equipment
J22 C P22 P/O Equipment
J22 D P22 P/O Equipment
C21B20 J22 E P22 P/O Equipment

F-26
TM 55-1520-210-23-3

Table F-5. Connector Replacement Chart (Cont)

WIRE NO. RECEPTABLE PIN PLUG WIRE NO.


C13A20 J22 F P22 P/O Equipment
J22 G P22 P/O Equipment
J22 H P22 P/O Equipment
M3C20 J22 J P22 P/O Equipment
J22 K P22 P/O Equipment
RZ1752C20 J22 L P22 P/O Equipment
RZ1854B20N J22 M P22 P/O Equipment
RZ1751B20 J22 N P22 P/O Equipment
J22 U P22 P/O Equipment
L22A20N J23 A P23 L22B20N
L21H20 J23 B P23 L21G20
Q52A20 J23 C P23 Q52B20
W102B20 J23 D P23 W102A20
W103B20 J23 E P23 W103A20
Q53D20 J23 F P23 Q53C20
J3H20 J23 H P23 J3G20
J4A20 J23 J P23 J4B20
J23 K P23
Q12D20 J23 L P23 Q12E20
J23 M P23
J23 N P23
J23 P P23
J23 R P23
J23 S P23
J23 T P23
J23 U P23
J23 V P23
J23 w P23
Q11A20 J23 X P23 Q11B20
Q1OB2O J23 Y P23 Q1OA2O
Q12A20 J23 Z P23 Q12B20
E37D20 J23 a P23 E37C20
E46A20 J23 b P23 E46B20
Q30A20 J23 c P23 Q30B20
Q29B20 J23 d P23 Q29A20
Q50A20 J23 e P23 Q50B20
E44A20 J23 f P23 E44B20
Q51A20 J23 g P23 Q51B20
J2A20 J23 h P23 J2B20
J1B20 J23 i P23 J1A20
Q4A20 J23 j P23 Q4B20
Q3B20 J23 k P23 Q3A20
H61A16 J23 m P23 H61B16
Q5A20 J23 n P23 Q5B20
Q1B20 J23 P P23 Q1A20
Q2A20 J23 q P23 Q2B20
H60C16 J23 r P23 H60B16

J2D20 J2B20 J25 A P25 J2E20


L43B20 J25 B P25 L43A20
L42A20 J25 C P25 L42B20
L30C20 J25 D P25 L30B20
J3B20 J25 E P25 J3A20
K2A20 J25 F P25 K2B20
L34B20 J25 G P25 L34A20
Q25B20 J25 H P25 Q25A20

F-27
TM 55-1520-210-23-3

Table F-5. Connector Replacement Chart (Cont)


WIRE NO. RECEPTABLE PIN PLUG WIRE NO.
L51B20 J25 J P25 L51A20
L20T20 J25 K P25 L20U20
J25 L P25
J25 M P25
J25 N P25
J25 P P25
J25 R P25
J3G20 P25 s P25 J3F20
Q24A20 J25 T P25 Q24B20
L53A20N J25 U P25 L53B20
Q26B20 J25 V P25 Q26A20
Q22B20 J25 W P25 Q22A20
Q23B20 J25 X P25 Q23A20
L33B20 J25 Y P25 L33A20
K3B20 J25 Z P25 K3A20
L44B20 J25 a P25 L44A20
L31B20 J25 b P25 L31A20
L38B20 J25 c P25 P38A20
D16B20 J41 A P41 D16A20
D17A20 J41 B P41 D17B20
J41 C P41
J41 D P41
J41 E P41
J41 F P41
J41 G P41
J41 H P41
J41 J P41
W19B20 J41 L P41 W19A20
J41 M P41
D5A20 J41 N P41 D5B20
D6B20 J41 P P41 D6 C20
D1B20 J41 R P41 D1A20
D22A20 J41 S P41 D22B20
D2B20 J41 T
U P41 D25B20N
D23A20 J41 V P41 D23B20
P/O Equipment J91 B P91
P/O Equipment J91 C P91 Q28A16
P/O Equipment J91 D P91 H61C16
P/O Equipment J91 E P91 E1A18
P/O Equipment J91 F P91 E2A18
P/O Equipment J91 G P91 E21A18
P/O Equipment J91 H P91 E22A18
P/O Equipment J91 J P91 J3E18
P/O Equipment J91 K P91 J4C18
P/O Equipment J91 L P91 Q12C18
P/O Equipment J91 M P91 Q11C18
P/O Equipment J91 N P91 E8A18
P/O Equipment J91 P P91 E9B18
P/O Equipment J91 R P91
P/O Equipment J91 U P91
P/O Equipment J91 V P91
P/O Equipment J91 D J91
H56A20 J92 A P92 H56A20
Q46B20 J92 B P92 Q46C18

F-28
TM 55-1520-210-23-3

Table F-5. Connector Replacement Chart (Cont)


WIRE NO. RECEPTACLE PIN PLUG WIRE NO.
P35A16 J92 C P92 P35B16
Q45B20 J92 D P92 Q45C18
Q47A20N J92 E P92 Q17B18
WI6B20 J92 F P92 W16A18
Q15A20 J92 G P92 Q15B18
H61B16 J92 H P92 H61C16
Q67B20N J92 J P92 Q67A18
Q66A20 J92 K P92 Q66B18
El]B20 J92 L P92 E1A18
E2B20 J92 M P92 E2A18
E21B20 J92 N P92 E21A18
E22B20 J92 P P92 E22A18
J 3D20 J92 R P92 J3E18
J 4B20 J92 s P92 J4C18
Q12B20 J92 T P92 Q12C18
Q28B16N J92 U P92 Q28A16
Q1 1B20 J92 V P92 Q11C18
E 8A20 J92 W P92 E8A18
E 9A20 J92 X P92 E9B18
E29B20N J92 Z P92 E29A18
Q17A20 J92 a P92 Q17B18
El I5A20 P92 b P92 E15B18
H55A20 P92 c P92 H55B18
H54A20 P92 d P92 H54B18
E5 B20 J92 e P92 E5A18
E33C-CHROM J92 f P92 E33B-CHROM
Q1 8A20N J92 g P92 Q18B18
E14A20 J92 h P92 E14B18
E3 1B20N J92 j P92 E31A18
E6 A20 J92 k P92 E6B18
E4 3C-ALML J92 m P92 E34B-ALML
Q3 1A18N J92 n P92 Q31B18
H57A20N J92 P P92 H57B18
H44A20 H52B20 J92 r P92 H52C18 H44B18
H45A20 H53A20 J92 s P92 H53B18 H45B18

Q46B20 J107 A P107 Q46A20


Q45B20 J107 B P107 Q45A20
Q24D20 J107 C PI07 Q24E20
Q22B20 J107 D P107 Q22C20
K2C20 J107 E P107 K2D20
J 2D20 J107 F P107 J2C20
J 2B20 J107 P107
Q23B20 J107 G PI07 Q23C20
J 3B20 J107 I P107 J3C20
J 3D20 J107 P107
K3 B20 J107 J P107 K3C20
K3 D20 J107 P107
NOTES
EFF When Rescue Hoist Provisions preinstalled.
EFF 65-9565 thru 66-16033
EFF 68-15214 thru 70-15932
EFF 65-9565 thru 66-16867
EFF 65-9565 thru 67-19537

218-261 0 - 88 -21 F-29/(F-30 blank)


TM 55-1520-210-23-3

Table F-5. Connector Replacement Chart (Cont)


WIRE NO. RECEPTACLE PIN PLUG WIRE NO.
P35A16 J92 C P92 P35B16
Q45B20 J92 D P92 Q45C18
Q47A20N J92 E P92 Q17B18
WI6B20 J92 F P92 W16A18
Q15A20 J92 G P92 Q15B18
H61B16 J92 H P92 H61C16
Q67B20N J92 J P92 Q67A18
Q66A20 J92 K P92 Q66B18
El]B20 J92 L P92 E1A18
E2B20 J92 M P92 E2A18
E21B20 J92 N P92 E21A18
E22B20 J92 P P92 E22A18
J 3D20 J92 R P92 J3E18
J 4B20 J92 s P92 J4C18
Q12B20 J92 T P92 Q12C18
Q28B16N J92 U P92 Q28A16
Q1 1B20 J92 V P92 Q11C18
E 8A20 J92 W P92 E8A18
E 9A20 J92 X P92 E9B18
E29B20N J92 Z P92 E29A18
Q17A20 J92 a P92 Q17B18
El I5A20 P92 b P92 E15B18
H55A20 P92 c P92 H55B18
H54A20 P92 d P92 H54B18
E5 B20 J92 e P92 E5A18
E33C-CHROM J92 f P92 E33B-CHROM
Q1 8A20N J92 g P92 Q18B18
E14A20 J92 h P92 E14B18
E3 1B20N J92 j P92 E31A18
E6 A20 J92 k P92 E6B18
E4 3C-ALML J92 m P92 E34B-ALML
Q3 1A18N J92 n P92 Q31B18
H57A20N J92 P P92 H57B18
H44A20 H52B20 J92 r P92 H52C18 H44B18
H45A20 H53A20 J92 s P92 H53B18 H45B18

Q46B20 J107 A P107 Q46A20


Q45B20 J107 B P107 Q45A20
Q24D20 J107 C PI07 Q24E20
Q22B20 J107 D P107 Q22C20
K2C20 J107 E P107 K2D20
J 2D20 J107 F P107 J2C20
J 2B20 J107 P107
Q23B20 J107 G PI07 Q23C20
J 3B20 J107 I P107 J3C20
J 3D20 J107 P107
K3 B20 J107 J P107 K3C20
K3 D20 J107 P107
NOTES
EFF When Rescue Hoist Provisions preinstalled.
EFF 65-9565 thru 66-16033
EFF 68-15214 thru 70-15932
EFF 65-9565 thru 66-16867
EFF 65-9565 thru 67-19537

218-261 0 - 88 -21 F-29/(F-30 blank)


R:\210-23-3\F-31.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-33.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-35.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-37.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

Figure F-6. Rpm limit warning test set schematic — BHT Model 205-074-033-103

Change 9 F-39
TM 55-1520-210-23-3

Figure F-7. Mission Antennas OE-201/AARQ-33 and OE-202/ARQ-33 Schematic Diagram


EH-1H

F-40
R:\210-23-3\F-41.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

Figure F-9. Door gunner’s foot mike switch

2 1 8 - 2 6 1 0 - 8 1 - 2 6 F-43
TM 55-1520-210-23-3
Figure F-10. Altimeter AAU-31/A and AAU-32/A and Transponder AN/APX-72 interconnecting
wiring diagram
F-44
TM 55-1520-210-23-3

Figure f-11. Tachometer generator system


F - 4 5
TM 55-1520-210-23-3

Figure F-12. AC pressure indicator system

F - 4 6
TM 55-1520-210-23-3

Figure F-13. Temperature bulb, turn and slip indicator system

F-47
TM 55-1520-210-23-3

Figure F-14. Exhaust temperature indicator system

F-48
TM 55-1520-210-23-3

205475-116A
AV 0564245

Figure F-15. PItot heater system


F-49
218-261 0 - 88 -27
TM 55-1520-210-23-3

Figure F-16. Attitude indicator system

F-50
TM 55-1520-210-23-3

Figure F-17. Fuel Quantity System


Change 4 F-51
TM 55-1520-210-23-3
Figure F-18. Battery system
F-52
TM 55-1520-210-23-3
Figure F-18.1.
Figure F-18.1. Battery system
218-261 0 -88 -28
F-53
R:\210-23-3\F-55.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3
F-57/(F-58
218-261 0 - 88 - 2 9 blank)
R:\210-23-3\F-59.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-61.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

Figure F-21 AC power system (sheet 1 of 2)


F-63/(F-64
blank)

218-261 0 - 88 -31
R:\210-23-3\F-65.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3
Figure F-21.1
F-67
TM 55-1520-210-23-3

Figure F-22. Starter system (65-9566 through 67-19637) (Sheet 1 of 2)

F-68
TM 55-1520-210-23-3

Figure F-22 Starter system (68-15214 and subsequent) (sheet 2 of 2)

F-69
TM 55-1520-210-23-3
Figure F-22.1 External 3 phase power system
F-70
TM 55-1520-210-23-3

Figure F-23. Ignition system (65-9565 through 66-16033) (Sheet 1 of 3)

F-71
TM 55-1520-210-23-3

Figure F-23. Ignition system (66-16034 through 67-19537) (Sheet 2 of 3)

F-72
TM 55-1520-210-23-3

Figure F-23. Ignition system (68-15214 and subsequent) (Sheet 3 of 3)

218-261 0 - 88 -33
F-73
TM 55-1520-210-23-3
Figure F-24. Cockpit, Dome and Crew Lights System
R:\210-23-3\F-75.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-233

REFERENCE: INSTRUMENT, CONSOLE AND PEDESTAL LIGHTING SYSTEM DIAGRAM

NOTE: SEE TM 11-1520-210-23 FOR PROCEDURE TO ADJUST ARC-201 PANEL VOLTAGE.

Figure F-25.1. ARC-201 Panel Lighting Wiring Diagram


(After application MWO 55-1520-210-50-21)

Change 8 F-76.1(F-76.2 blank)


TM 55-1520-210-23-3

Figure F-25.2. Night Vision Goggles (Night Fix-Phase I) Lights System

Change 8 F-77
TM 55 1520-210-23-3
Figure F-26. Caution lights system (60-6028 through 64-13901)
(Sheet 1 of 3)
F-78
R:\210-23-3\F-79.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

Figure F-26 Caution lights system (66-16868 and subsequent) (sheet 3 of 3)

F-81/(F-82
blank)
R:\210-23-3\F-82-1.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3
Figure F-26.1. 5 VOLT Instrument Lighting System (UH-1V)
218-261 0 - 88 -36
F-83/(F-84
blank)
R:\210-23-3\F-85.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3
Figure F-28. Landing and searchlight system
218-261 0 - 88 -37
TM 55-1520-210-23-3

Figure F-29. Navigation, fuselage, and anti-collision lights system


TM 55-1520-210-23-3

Figure F-30. De-ice and ice detector system

F-89/(F-90
blank)
218-261 0 - 88 -38
R:\210-23-3\F-91.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-93.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3
Figure F-32. Governor control and idle atop systems
F-95/(F-96
blank)
TM 55-1520-210-23-3

FIGURE F-33. FORCE TRIM AND HYDRAULIC CONTROL SYSTEM (SHEET 1 OF 2)

F-97
218-261 0 - 88 -41
TM 55-1520-210-23-3

FIGURE F-33. FORCE TRIM AND HYDRAULIC CONTROL SYSTEM (SHEET 2 OF 2)

F-98
R:\210-23-3\F-99.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-101.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

Figure F-35. Heated Blanket Receptacle System

F-103
218-261 0 - 88 -43
TM 55-1520-210-23-3

Figure F-36. Windshield Wiper System

F-104
TM 55-1520-210-23-3

Figure F-37. Cargo hook system

F-105/(F-106
218-261 0 -88 -44
blank)
R:\210-23-3\F-107.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-109.TIF

Printed by ViewDirector Version 2.100 demonstration application


Figure F-38.1. High Performance Utility Helicopter Hoist System

F-111/(F-112
blank)
TM 55-1520-210-23-3

Figure F-39. External fuel system

218-261 0 - 88 -47
F-113
TM 55-1520-210-23-3

Figure 40. Fire Detector System


F-114 Change 4
R:\210-23-3\F-115.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-117.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-119.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-121.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-123.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-125.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-127.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-129.TIF

Printed by ViewDirector Version 2.100 demonstration application


R:\210-23-3\F-131.TIF

Printed by ViewDirector Version 2.100 demonstration application


TM 55-1520-210-23-3

ALPHABETICAL INDEX

Paragraph Paragraph

A Alignment-Main Driveshaft P/N 205-040-004


Allocation Chart-Maintenance . . . . . . . . . . . . . . . . . . . .
6-24
B-1
Allocation Chart--Use of the Maintenance... B-2
AC Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-113
Alternating Current Power Distribution
AC Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-298
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-98
Acceptance/Rejection Criteria-Transmission
Altimeter-Barometric-Troubleshooting . . . . T8-10
Assembly-Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
AN/APR-39 (When Installed)-Radar Warning
Access & Inspection Provisions . . . . . . . . . . . . . . . . . . . . . F2-18
Indicating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-314
Access Covers & Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
AntiCollision Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-211
Actuator, Linear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-118
AntiCollision Light System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-207
Adapter and Cap Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-77
Appendix A-References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Adapter and Plate. . . . . . . . . . . . . . . . . . . . . . . . . . ....... . . . . . . . . . F14-20
Appendix C—Aircraft Inventory Master
Adjustable Window-Crew Door . . . . . . . . . . . . . . . . . . 2-154
Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Adjuster Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-115
Appendix D-Illustrated Field Manufacture
Adjustment Procedures (Crashworthy)-Circuit
Item List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Arrangement-Adapter Cable . . . . . . . . . . . . . . . . . . . . F8-7
Appendix E Intermediate Storage . . . . . . . . . . . . . . . . . . E-12
Aft Center Fuel Cell Coverplate . . . . . . . . . . . . . . . . . . . . 10-72
Appendix E-Storage, Short Term . . . . . . . . . . . . . . . . E-3
Aft Landing Gear Attachment
Appendix E Storage of Aircraft
Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-24.1, F-24.4
Appendix E Flyable Storage . . . . . . . . . . . . . . . . . . . . . . . . . l E-2
Air Blower-Combustion Heater . . . . . . . . . . . . . . . . . . . 13-57
Armament Control-Panel Assembly . . . . . . . . . . . . 16-89
Air Blower-Exhaust Heater . . . . . . . . . . . . . . . . . . . . . . . . . 13-95
Armament couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
l 7-108
Aircraft All Weather Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . F1-11
Armament Junction Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-101
Aircraft Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 1-45
Armament Subsystem 7.62MM Machine
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-46
Gun M23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-27
Aircraft Inventory Master Guide Appendic C C-1
Armament Subsystem M23 Machine Gun
Aircraft Jacking and Leveling . . . . . . . . . . . . . . . . . . . . . . . . 1-36
M60D in Stowed Position rS . . . . . . . . . . . . . . . . . . . . F16-12
Aircraft Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
Armament Subsystem-M59 . . . . . . . . . . . . . . . . . . . . . . . . . 16-32
Air Falter Switch-Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9-4
Armament Subsystem M59 Main Compo-
Air Induction System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
nents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F16-23
Air Induction System, Non-Self-Purging
Armored Crew seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-247
Particle Separator-Description . . . . . . . . . . . . . . . . . 4-29
Armored Crew Seat Headguard . . . . . . . . . . . . . . . . . . . . . F2-48
Air Induction System Louver and Filter type 4-14
Attitude Indicating System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-190
Air Induction System-Non-Self-Purging
Attitude Indicator-Troubleshooting............. T8-1 1
Particle Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Attitude Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-192
Air Inlet Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Auxiliary Exhaust Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-84
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Auxiliary Exhaust Heater-Heat Exchanger. 13-87
Air Inlet Filters-Inpection. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Auxiliary Exhaust Heater System Schematic F13-10
Air Inlet Screens--Non-Self-Purging Particle
Auxiliary Fuel Cell Fill Cap-Crashworthy.. 10-171
Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
Auxiliary Fuel Cell Fuel Gage-Crashworthy 10-167
Air Intake Bellmouth, Screen and Baffles- Auxiliary Fuel Cell Fuel Pump . . . . . . . . . . . . . . . . . . . . . . 10-157
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Auxiliary Fuel Cell Pump Assembly-
Air Intake, Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Crashworthy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-183
Air Particle Separator-Self-Purging . . . . . . . . . . . . . 4-52
Auxiliary Fuel Cell Refuel Receiver-
Air Particle Separator-Self-Purging-Air
Crashworthy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-179
Induction System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
Auxiliary Fuel Cell Shutoff Valve-Crash-
Air Particle Separator-Self-Purging-Inlet worthy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-181
Foreign Object Damage (FOD) Screen . . . . . . 4-46
Auxiliary Fuel Provisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-156
Air Particle Separator-Self-Purging-Air Auxiliary Fuel System-Servicing . . . . . . . . . . . . . . . . 1-4
Induction System—Description . . . . . . . . . . . . . . . . . 4-44
Auxiliary Fuel System-300 Gallon Crash-
Airpeed Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-172 worthy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-161

Change 4 Index 1
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

B Circuit Breaker-AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-91


Circuit Breaker-DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Baffle Assembly-Induction . . . . . . . . . . . . . . . . . . . . . . . . . . Classification of Damage-Honeycomb
2-72
Barometric Altimeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-5
8-181
B a t t e. . . r. . .y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Classification of Damage-Sheet Metal
9-30
Battery Feeder Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skins Forward Fuselage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-6
9-41
Battery Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
9-39
Battery system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning & Treating Corroded Parts . . . . . . . . . . . . . T M
9-26
Battery System-Troubleshooting . . . . . . . . . . . . . . . . Cleaning-Power Plant Assembly . . . . . . . . . . . . . . . . . 4-4
T9-1
Beam-Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-231
2-58
Beam-Lift-Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock-Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T8-15
F2-22
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closed Circuit Refueling Receiver . . . . . . . . . . . . . . . . 10-83
11-185
Closed Circuit Refueling Receiver . . . . . . . . . . . . . . . . 10-88
Bellcranks Levers and Supports-Collective
Cockpit Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-142
Control System.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147
Cockpit Lights-Troubleshooting . . . . . . . . . . . . . . . . . T9-8
Bellcranks, Levers and supports-cyclic
Collective Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
Control System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 11-101
Collective Jackshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Bellcranks, Levers and Supports--Elevator
Collective Levers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68
Control System.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-179
Bellcranks, Levers, and Support-Tail Collective Stick Copilots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-34
collective Stick, Pilots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-25
Rotor Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-164
Compass-Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-225
Blackout Curtains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-186
Compass-Standby-Troubleshooting . . . . . . . . . T8-14
Blade, Main Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 5-27
Composite Main Rotor Blade . . . . . . . . . . . . . . . . . . . . . . . . 5-34.2
Blade Composite Main Rotor . . . . . . . . . . . . . . . . . . . . . . 5-34.2
Blades, Tail Rotor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 9 . 1 , 5 - 3 4 . 4
5-114
Blanket Receptacles-Heated . . . . . . . . . . ..... Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34.3
9-276
Bleed Air and Defroster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preliminary Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34.5
13-1
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34.6
Bleed Air Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-270
Composite Main Rotor Blade UH-1H F5-26. 1
Bleed Check Valve-Governor . . . . . . . . . . . . . . . . . . . . . 10-46
Example of When to Use Pitch Link
Blood Bottle Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-105
Versus Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5-87.2
Boost Pumps-Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-94
Vibrex Chart for Vertical l/Rev F5-87.3
Brake-Cyclic Controls, Magnetic . . . . . . . . . . . . . . . . 11-73
Connector Replacement Chart . . . . . . . . . . . . . . . . . . . . . . . F-9
Breakaway Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-155
Console-Pedestal Lights-Instrument . . . . . . . . . 9-160
Breaker Valve-Siphon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-66
Consumable Maintenance Supplies and
Build-up-Universal Transmission Assembly F6-15
Bulb-Engine Oil Temperature . . . . . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
8-90
Consumable Maintenance Supplies and
Bus Control Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-83
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1-1
Bus Relay-Nonessential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-87
Control Assembly-Collective JackShaft . . . . . . 11-17
Control Panel, Mine Dispenser . . . . . . . . . . . . . . . . . . . . . . 16-38
c Control Panel-M6 Subsystem 7.62MM
M60C Machine Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-64
Cabin Floor Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Cabin Roof Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-161 Control Quadrant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-137
Cabin Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1347 Control Relay—Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-83
Center Service Deck Panel Repair . . . . . . . . . . . . . . . . . F2-12 Control Tube and Quill—Tail Rotor . . . . . . . . . . . . . . 11-143
Check Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140 Control Stick, Cyclic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-56
Check Valve-Governor Bleed . . . . . . . . . . . . . . . . . . . . . 10-46 Control System Circuitry+Governor . . . . . . . . . . . . 9-252
Check Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26 Control System Circuitry-Hydraulic . . . . . . . . . . . 9-226
Chip Detector/Oil Contamination . . . . . . . . . . . . . . . . . . 4-101 Control System, Collective . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
Control System, Elevator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-170

Index 2 Change 4
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Control System Flight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1


Control Tubes-Collective Control System... 11-41
Control Tubes-Cyclic Control System . . . . . . . . . 11-41
Damage Classification-General-Corrosion T2-3
Control Tubes-Elevator Control System . . . . . 11-173
Damage-Classification-Honeycomb
Control Tubes-Tail Rotor Control System... 11-158
Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-5
Controls & Accessories-Engine . . . . . . . . . . . . . . . . . . . 9-242
Damage Limits-Intermedate Gearbox
Controls, Tail Rotor Crosshead . . . . . . . . . . . . . . . . . . . . . . 5-107
Support Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2.62.1
Conversions-Decimal Equivalent . . . . . . . . . . . . . . . . F1-5
Damage LimitsRepair-Lift Beam . . . . . . . . . . . . F2-21
Converter Assembly . . . . . . . . . . . . . . . . . . . . . . . .... . . . . . . . . . F12-7
Dampers and Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T12-3
Dampers-Friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-149
Converter &Motor Assy-L/R Configuration F12-7
DC Bus System-Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 9-56
Cooler Assembly-Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-217
DC Bus System-Generator-Troubleshooting
Copilots Collective Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-34
(Helicopters Prior to S/N 66-746) . . . . . . . . . . . . . . T9-3
Corrosion-Aluminum and Magnesium Alloy,
DC Bus System-Generator-Troubleshooting
Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
(Helicopters S/N 66-746 and Subsequent.. T9-4
Corrosion Damage Classification-General T2-3
DC Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Coupling-Quick Disconnect-Inspection . . . F6-23
DC Generator-Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-60
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-151
DC Voltmeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-300
couplings, Armament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-108
Debris Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-49.1
Couplings-Inner-Spherical on Main
Decimal Equivalent Conversions . . . . . . . . . . . . . . . . . . . F1-5
Driveshaft-inspection Criteria . . . . . . . . . . . . . . . . . F6-3
Defroster Installation-Bleed Air . . . . . . . . . . . . . . . . . . 13-1
Course Indicator (ID-1347( )/ARN) . . . . . . . . . . . . . . 8-221
Defroster Installation-Combustion Heater
Covers-Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-45
and . . . . . . . . . . . . . . . . . . . . . . . ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
Cowling-Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44
De-ice Circuitry-Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-244
Cowling-Transmiss . ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Dimensions-Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1-7
Cowling-Transmiss ion &Engine . . . . . . . . . . . . . . . . F2-20
Direct Current Power Distribution System . . . . 9-1
Cowlings & Fairings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Dome Lights . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-151
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Doors-Access Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Crew Door Jettison (Ejection) Mechanism . . . . 2-98
cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-114
Crew Door Jettison Mechanism . . . . . . . . . . . . . . . . . . . . . F2-31
crew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-28
crew Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84
Nose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77
Crew Doors-Latching Mechanism . . . . . . . . . . . . . . . 2-92
Drain Valve-Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-26
crew Seat-Armored . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-247, F2-47
Drive Quill-Tail Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-125
Crew Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-241
Driveshaft Assembly-Main-Limits
Crew Seat Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-45, 2-225
Chart P/N 205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-10
Crew Seat-standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-216
Driveshaft Hangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-167
Critical Areas & Repair Limits-Windshield &
Aft Tailboom Installation . . . . . . . . . . . . . . . . . . . . . . . . F6-50
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-41
Coupling Teeth Wear Patterns . . . . . . . . . . . . . . . . F6-46
Cross Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-101
Forward Tailboom Installation . . . . . . . . . . . . . . . . F6-49
Crosshead Controls, Tail Rotor . . . . . . . . . . . . . . . . . . . . . . 5-107
Fuselage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-48
Crossover Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-59
Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-45
Curtains-Blackout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-186
Driveshaft-Main P/N SKCP2281-1 . . . . . . . . . . . . . 6-24.1
Cyclic Control Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-56
Driveshaft-Main P/N 204-040-004 . . . . . . . . . . . . . 6-13
Cyclic Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-53
Driveshaft Main-Alignment P/N
205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
Driveshaft-Main-Assembly and Installation
P/N 205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-9
Driveshaft-Main Disassembly P/N
205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18

Change 4 Index 3
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Driveshaft-Main-Cleaning P/N Engine Oil Contamination Troubleshooting.. 4-106.9


205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19 Engine Oil Pressure Indicator . . . . . . . . . . . . . . . . . . . . . . . . 8-60
Driveshaft-Main-Inspection P/N Engine Oil Pressure Transmitter . . . . . . . . . . . . . . . . . . . . 8-69
205440-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 Engine Oil System-servicing . . . . . . . . . . . . . . . . . . . . . . 1-5
Driveshaft-Main-Inspection of Installed Engine Oil Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-84
P/N 205-040-004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15 Engine Oil Temperature Bulb . . . . . . . . . . . . . . . . . . . . . . . . 8-90
Driveshaft Main-Installation P/N Engine Oil Temperature Indicator . . . . . . . . . . . . . . . . . . 8-80
205440-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23 Engine Quick Change Assembly . . . . . . . . . . . . . . . . . . . . 4-133
Driveshaft Main P/N 205-040-004-Lubri Engine Vibration Meter Receptacle . . . . . . . . . . . . . . . 9-120
cation and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 Equipment Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-7
Driveshafk-Main-Removal P/N Equipment Location-Electrical . . . . . . . . . . . . . . . . . . . . F9-2
205-00004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17 Example of When to Use Pitch Link Versus
Driveshaft Main P/N 205-040-004 . . . . . . . . . . . . . . . . . 6-21 Tab ................................................ F5-87.2
Driveshaft-Main-Troubleshooting Example of When to Use Tab Alone F5-87.3
P/N 205—00004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T6-2, 6-16 Exhaust Gas Temperature Indicating System 8-99
Driveshaft-Tail Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-159 Exhaust Gas Temperature Indicator . . . . . . . . . . . . . . . 8-101
Droop Compensator Controls . . . . . . . . . . . . . . . . . . . . . . . . . 4-126 Exhaust Heater-Air Blower . . . . . . . . . . . . . . . . . . . . . . . . . 13-95
Dual Tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Exhaust Heater-Auxiliary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-84
Dual Tachometer-Troubleshooting . . . . . . . . . . . . . . T8-1 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58
Ducts, Nozzles, Registers, Gaskets and Exhaust System-Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
Miscellaneous Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4 Exhaust System-Tailpipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67
Exterior-Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Exterior-Lights System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-194
E External Oil Filter, Eng (ODDS) . . . . . . . . . . . . . . . . . . . . 4-106.13
External Oil Filter, Xmsn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-57, 6-204
EGT Indicator Scale &Friction Error Tol- External Oil Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-57, 6-204
erances Plus or Minus 0 Celsius . . . . . . . . . . . . . . . . . T8-6 External Power—Application . . . . . . . . . . . . . . . . . . . . . . . . 1-53
Electrical-Component Location . . . . . . . . . . . . . . . . . . . F9-1 External Power Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-47
Electrical Components (AC)-Common . . . . . . . 9-91 External Power Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-54
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-92 External Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-43
Electrical Components (DC)-Common . . . . . . . 9-3 External Power System-Troubleshooting . . . . T9-2
Electrical Components-Miscellaneous . . . . . . . . 9-5 External Stores Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1
Electrical Equipment Location . . . . . . . . . . . . . . . . . . . . . . . F9-2 External Stores Support Assembly . . . . . . . . . . . . . . . . . F16-1
Elevator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-286 Extinguisher and Bracket, Fire . . . . . . . . . . . . . . . . . . . . . . . 17-7
Elevator, Bearing Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-55
Elevator Control Assy-Removal and In-
stallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-54 F
Elevator Control System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-170
Elevator Support & Horn Assy-Wear & Fairing-Tailpipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51
Damage Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-56 Feeder Relay-Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-41
Emergency Jettison Release Mechanism . . . . . . . 16-8 Field Relay-Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-79
Engine Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Fifth Mount Support-Pylon . . . . . . . . . . . . . . . . . . . . . . . . . 2-62
Engine Controls & Accessories . . . . . . . . . . . . . . . . . . . . . . 9-242 Fire Detection System-Engine . . . . . . . . . . . . . . . . . . . . . 12-1
Engine Cowling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Fire Extinguisher Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7
Engine Cowling-Transmission . . . . . . . . . . . . . . . . . . . . F2-20 Firewall and Tailpipe Assembly Installation.. 4-143
Engine De-Ice Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-244 Firewalls & Heat Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
Engine De-Ice Circuitry-Troubleshooting... T9-15 First Aid Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1
Engine Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Fittings & Screens, Lines, Manifolds . . . . . . . . . . . . . 6-81
Engine Mounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-50, 2-267 Fitting-Support Tail Rotor Driveshaft . . . . . . . . 6-174

Index 4 Change 4
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Flasher-Navigation Lights........................... 9-229 Functional Check Low Fuel Caution


Flight Control System ................................. 11-1 System................................................. 10-19.1
Flight Control System (Electrical) ............... 9-260 Fuselage .................................................... 2-1
Description ........................................... 8-162 Fuselage Skin - Forward ............................ F2-4
Flight Safety Critical Aircraft Parts.............. 1-67 Fuselage Structure..................................... 2-3
Floor Panels - Cabin................................... 2-28
Fluid Connectors - Torque Values.............. T1-5 G
Flyable Storage Appendix E....................... E-4
Force Gradient Cyclic Controls................... 11-80 Gages - Oil Level Sight .............................. 6-75
Force Gradient -- Tail Rotor Controls ......... 11-113 Gas Producer Tachometer Generator ....... 8-49
Force Trim System Circuitry....................... 9-262 Gas Producer Tachometer Indicator.......... 8-40
Forward Door Window -Crew Door ............ 2-147 Repair or Replacement........................ 8-46
Forward Towing.......................................... 1-35 Gas Producer NI Tachometer Generator
Free Air Temperature Gage ....................... 8-305 Installation............................................ 4-151
Friction Dampers ........................................ 6-149 Gas Temperature Indicating System -
Friction Damper Mount............................... F2-23.3 Exhaust................................................ 8-99
Friction Damper Retaining Clip .................. F2-23.1 Gas Temperature Indicator - Exhaust........ 8-101
Fuel Boost Pump Cross Fitting................... 10-107 Gaskets and Miscellaneous Valves -
Fuel Boost Pumps ...................................... 10-100 Ducts, Nozzles, Registers ................... 13-4
Fuel Boost Pump, Cartridge ....................... 10-105.1 Gearbox - Intermediate (42 Degree).......... F6-51,6-179
Fuel Cap and Adapter Assembly................ 10-78 Gearbox - Tail Rotor .................................. F6-52,6-190
Fuel Cell Coverplate -Aft Center................. 10-72 Gearboxes -- Intermediate (42 Degree) and
Fuel Cells -- Crashworthy........................... 10-1 Tail Rotor (90 Degree) -
Fuel Cell Drain Valve.................................. 10-27 Servicing.............................................. 1-8
Fuel Cell Sump Assembly .......................... 10-135 Gearboxes -- Transmission Assy, Identification
Fuel Check Valve ....................................... 10-150 of Metal Particles (Without ODDS) ...... F6-14,6-30
Fuel Crossover Assemblies........................ 1060 Gearboxes - Transmisson Assy, Decision Criteria
Fuel Ejector Pump ...................................... 10-116 for Replacement (Without ODDS) ........ F6-14.2,6-30.1
Fuel Filter Assembly................................... 10-20 Generator & DC Bus System .............. 9-56
Fuel Flapper Valve ..................................... 10-122 Generator & DC Bus System (Helicopters
Fuel Flapper Valve Plates .......................... 10-128 Prior to S/N 66-7460) -
Fuel Flow Switch ........................................ 10-145 Troubleshooting................................... T9-3
Fuel Governor Bleed Check Valve ............. 10-47 Generator & DC Bus System - (Helicopters
Fuel Manifold Assembly ............................. 10-54 S/N 66-746 and Subsequent) -
Fuel Motor Driven Shutoff Valve................. 10-40 Troubleshooting................................... T9-4
Fuel Pressure Differential Transmitter ....... 4-147 Generator Drive Quill ................................. 6-109
Fuel Pressure Transmitter.......................... 10-33 Generator Field Relay ................................ 9-79
Fuel Quantity Transmitters ......................... 10-112 Generator - Main DC.................................. 9-60
Fuel Siphon Breaker Valve......................... 10-66 Generator - Power Turbine Tachometer .... 8-22
Fuel Warning System 20 Minute Float Generator - Rotor Tachometer................... 8-31
Switch .................................................. 10-93 Generator Shunt......................................... 9-69
Fuel Boost & Fuel Valve Circuitry............... 9-248 Generator - Standby (Starter
Fuel Pressure Indicating System................ 8-121 Generator) ........................................... F9-2.1,967
Fuel Pressure Indicator .............................. 8-128 Generator - Starter ............................... 9-126
Fuel Quantity Indicating System................. 8-241 Governor Bleed Check Valve..................... 10-46
Fuel Quantity Indicator ............................... 8-248 Governor Control System Circuitry ............ 9-252
Fuel Quantity Indicator - Troubleshooting .. T8-16 Governor Control System Circuitry -
Fuel Quantity Transmitters ......................... 8-252 Troubleshooting................................... T9-16
Fuel Solenoid Valve - Start......................... 9-136 Ground Handling ........................................ 1-32
Fuel Train - Heater ..................................... 13-36 Ground Handling Wheel Pump - Servicing 1-10
Fuel Valve & Fuel Boost Circuitry............... 9-248 Ground Handling Wheel Tires - Servicing.. 1-11
Ground Test Conditions ............................. 7-33
Gun Firing Relay M6 Subsystem ............... 16-72

Change 8 Index 5
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

H I

Hangers-Driveshaft ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6167 Icing System Test Box Schematic . . . . . . . . . . . . . . F9-3


Heat Exchanger-Auxiliary Exhaust Heater 13-9 (ID-1347( )/ARN) - Course Indicator . . . . . . . . . . 8-221
Heat Shield- Firewalls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66 (ID-998( )/ASN & ID-250( )/ARN-Radio
Heat Suppressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-51, 2-273 Magnetic Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-223
Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9 Identification of Metal Particles - Trans-
Heated Blanket Receptacles . . . . . . . . . . . . . . . . . . . . . . . 9-276 mission Assembly & Gearboxes . . . . . . . . . . . . . P6-14, 6-30
Heater Air Pressure Switches . . . . . . . . . . . . . . . . . . . . . . 13-52 Idle Stop System Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . 9-256
Heater Fuel Train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-36 Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-130
Heating System Circuitry - Bleed Air.., . . . . . . 9-270 Ignition Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-134
Heater System Circuitry - Muff . . . . . . . . . . . . . . . . . . 9-273 Ignition Unit and Igniter Plug-Combustion
Helicopter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-1 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-27
Helicopter Assembly (EH-lH) . . . . . . . . . . . . . . . . . . . . F2-1.1 Igniter Plug-Combustion Heater Ignition
Helicopter Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1-7 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-27
Hinged Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-104 Indicating System (AN/APR-39 (When
Hinged Panel Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-32 Installed)-Radar Warning . . . . . . . . . . . . . . . . . . . . . . . 8-314
Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-47 Indicating System-Attitude . . . . . . . . . . . . . . . . . . . . . . . . . 8-190
Hoisting-Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-50 Indicating System-Engine Oil Temperature 8-78
Hoist Rescue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Indicating System-Exhaust Gas Temperature 8-99
Hoist System Circuitry - Rescue (Provisions) 9-286 Indicating System-Fuel Pressure . . . . . . . . . . . . . . . . . 8-121
Honeycomb Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Indicating System-Fuel Quantity . . . . . . . . . . . . . . . . 8-241
Classification of Damage . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Indicating System-Torque Pressure . . . . . . . . . . . . . 8-141
Honeycomb Panels - Classification of Indicating System-Transmission Oil
Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-5 Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-258
Honeycomb Panels - Minor Damage Repairs F2-7 Indicating System-Transmission Oil
Honeycomb Panels - Repair of Dents, Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-278
Scars& Scratches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-6 Indicating Systems-Tachometer . . . . . . . . . . . . . . . . . . 8-12
Hook System Circuitry - Cargo . . . . . . . . . . . . . . . . . . 9-283 Indicator-Airspeed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-172
Hoses, Oil Lines and Fittings . . . . . . . . . . . . . . . . . . . . . . 4-77 Indicator-Airspeed-Troubleshooting . . . . . . . . . . . T8-9
Hoses, Tubing, Attaching Hardware . . . . . . . . . . . 7-114 Indicator-Engine Oil Temperature . . . . . . . . . . . . . . 8-80
Hub and Blade Assembly, Main Rotor . . . . . . . . 5-3 Indicator-Exhaust Gas Temperature . . . . . . . . . . . . 8-101
Hydraulic Control 1 System Circuitry . . . . . . . . . . . 9-266 Indicator-Fuel Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-123
Hydraulic Cylinder and Support Tail Rotor 11-63.1 Indicator-Fuel Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-243
Hydraulic Filter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 7-46 Indicator-Gas Producer Tachometer . . . . . . . . . . . 8-40
Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19 Indicator (ID- 1347()/ARN)-Course . . . . . . . . . . . . 8-221
Hydraulic Pump & Tachometer Drive Quill 6-118 indicator Torque Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-143
Hydraulic Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 indicator-Transmission Oil Pressure . . . . . . . . . . . 8-260
Hydraulic Reservoir - Servicing . . . . . . . . . . . . . . . . . 1-9 indicator-Transmission Oil . . . . . . . . . . . . . . . . . . . . . . . . . 8-280
Hydraulic Servo Cylinder Assembly (Col- Indicator-Turn & Slip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-201
lective Control ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-80 lndicator-Vertical Velocity . . . . . . . . . . . . . . . . . . . . . . . . . 8-210
Hydraulic Servo Cylinder Assembly indicators-Attitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-192
(Cyclic Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-67 induction Baffle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 2-72
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7-1 ,7-1 inertia Reel-Shoulder Harness-Crew
Standard Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-231
Infrared Suppressor-Duct Assembly
Outer Jacket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-279.1

Index 6 Change 5
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Inlet Foreign Object Damage (POD) Inverter Power Relay—Main . . . . . . . . . . . . . . . . . . . . . . . . . 9-105


Screen-Air Particle Separator-Self- Inverter Power Relay Spare. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-107
Purging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inverter Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-109
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49 Inverter System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-93
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51 Inverter System—Troubleshooting . . . . . . . . . . . . . . . . T9-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47 Inventory Items List Component Diagram . . . . FC-1
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50 Irreversible Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-92
Inlet Screen-Non-Self-Purging Air Particle Isolation of Circuits for Alignment-RPM
Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limit Warning Detector Models . . . . . . . . . . . . . . . . . T9-9
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36 J
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 Jack Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-198
Input Drive Quill P/N 205-040-263 . . . . . . . . . . . . . . . F6-26, 6-101 Jacking and Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-86
Input Drive Quill P/N 204-040-363 . . . . . . . . . . . . . . . F6-24, 6-92 Jackshaft Collective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Input Drive Quills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-90 Jettison (Ejection) Mechanism-Crew Door. 2-98
Input Driveshaft P/N 205-040-004-Lub Jettison Release Mechanism-Emergency . . . . 16-8
rication and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-11 Junction Box, Armament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-101
Inspection-Acceptance/Rejection
Criteria-Transmission Assembly . . . . . . . . . . . . . . 6-28
K
inspection—MainDriveShaft P/N
205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Inspection of Installed Main Driveshaft Kits, First Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1
P/N 205-040-004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 6-15
Inspection, Preliminary Composite Main L
Rotor Blade- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5-34.5
Inspection of Roller Chain (Chain Landing and Searchlight System . . . . . . . . . . . . . . . . . . . . 9-197
Removed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Landing and Searchlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-200
Inspection-Special . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-58 Landing Gear Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Inspection-Transmiss ion Assembly . . . . . . . . . . . . . 6-33 Landing Gear Crosstubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Inspection-T ransmiss Oil Filter . . . . . . . . . . . . . . 6-45 Latch-Cargo Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-122
Installation—Main . Driveshaft P/N Latch-Typical-Cargo Door . . . . . . . . . . . . . . . . . . . . . . . . F2-35
205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23 Latching Mechanism Crew Doors . . . . . . . . . . . . . . . . . 2-92
Installation-Transmission Assembly . . . . . . . . . . . . Latching Mechanism-Crew Door . . . . . . . . . . . . . . . . F2-29
Installation-Transmission Oil Filter . . . . . . . . . . . . . 6-49 Launcher and Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-80
Instrument Console, & Pedestal Lights . . . . . . . . . 9-160 Lead Spool Resistor-Thermocouple . . . . . . . . . . . . 8-111
Instrument Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Leveling and Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-36
Instrument Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-315
Lever Assembly+cyclic Controls, Tube and 11-65
Instrument Premaintenance Requirements . . . 8-8 Levers and Supports-Cyclic Control System,
Instruments-Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Bell Cranks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-101
Instruments-Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-161 Lift Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58
Instruments-Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . 8-229 Lift Beam Damage Limits and Repair . . . . . . . . . . . F-2-21
Instruments-Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-219 Lift Beam-Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-22
Intermediate Storage-Appendix E . . . . . . . . . . . . . . . E-10 Lift Link-Pylon Mounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-142
Interior-Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16 Light—Anticollision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-211
Interior Lights System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-140 Light System-Anticollision. . . . . . . . . . . . . . . . . . . . . . . . . . 9-207
Intermediate Gearbox (42°) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-179 Light System-Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-169
Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-97
Inverter Failure Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-111

Change 4 Index 7
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Light-Transmission Oil Level . . . . . . . . . . . . . . . . . . . 9-236 Main Rotor Hub and Blade Assembly . . . . . . . . . . . 5-3
Lighting Provisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-138 Adjustment Collective Pitch Forces . . . . . . 5-8
Lighting System Instrument, 5 volt . . . . . . . . . . . . . . . 9-86.1 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Lights-Cockpit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....... 9-142 Automation RPM Adjusting . . . . . . . . . . . . . . . . . . 5-10
Lights-Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-151 Cleaning . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Lights-Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-222 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Lights-Navigation-Flasher 9-229 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Lights System-Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-194 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Limits Chart-Main Driveshaft Assembly, Operational Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
P/N 205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-10 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 5-12
Linear Actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-118 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Lines, Manifolds, Fittings and Screen s . . . . . . . . 6-81 Main Rotor Mast Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 6-134
Lines Manifold, Fittings and Screens Main Rotor System. . . . . . . . . . . . . . . . . .... . . . . . . . . . . . . . . . . 5-1
Transmission Assembly . . . . . . . . . . . . . . . . . . . . F6-19 Maintenance Allocation Chart . . . . . . . . . . . . . . . . . . . B-1
Litter Rack . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 16-15 Maintenance-Instrument . . . . . . . . . . . . . . . . . . . . . . 8-1
Loadmeter . . . . . . . . . . . . . . 8-303 Manifold Assembly .. . . . . . . . . . . . . . . . . . . . . . . . . . . 10-53
Lower Case Repair-Tmnsrnission Assembly Manifolds, Fittings, and Lines . . . . . . . . . . . . . . . 6-81
( A V I M ) ... . . . . . . . . .. . . . . . . . . 6-37 Map and Data Case . . . .. . . . ..... 2-210
Lower Forward Cabin Windows . . . . . . . . . . . . . . 2-168 Mark 8 Sight Assembly . .... . . . . . . 16-97
Lubrication Chart . . . . . . . . . . F1-6 Master Caution Panel . . . . . . . . . . 9-173
Lubrication Instructions . . . . . . . . . . . . . . . . . . . . . 1-30 Master Guide-Aircraft Inventory Appendix C C-l
Lubrication-Transmision ion Assembly . . . . . . . . . . 6-27 Metal Surfaces Bonded Panels-Repair of
Voids . . . . . . . . . . . . . . . . . . . . . . . F2-10
Mine Dispenser Control Panel . . . . . . . . . . . . . . . . 16-38
Mine Dispenser M56 . . ... . .. . . . . . . . . ... 16-43
Mine Dispensing Subsystem . . . . . . . . . . ... 16-37
Machine Gun-M6 Subsystem 7.62MM, M60C 16-51 Minimum Breakaway Torque for Used All
Machine Gun M60D in Stowed Position Metallic and Nonmetallic Self-Locking Nuts TI-7
RS, Armament subsystem M23 . . . . .... F16-12 Miscellaneous Electrical Components . . . . . . . 9-5
Machine Gun XM213, .50 Caliber.. . . . . . .. . F16-22 Miscellaneous Equipment . . . . . . . . . . . . . . . . . . . . . . . . 9-240
Magnetic Brake-Cyclic Controls . . . . . 11-73 Miscellaneous Instruments . . . . . . . . . . . . 8-229
Magnetic Brake-Tail Rotor Controls . . . . . .. 11-111 Mission Antenna Actuator System .... . . . . .. 9-289
Magnetic Indicators-Radio (ID 998( )/ Mission Antenna Mount-Aft . . . . . . . . . . . . . . 9-310, F9-15
ASN and ID-250( )/ARN) . . . . . . . . . . .. . . . . 8-223 Mission Antenna Mount-Forward. . . . . . . . . . . . . . .9-291, F9-11
Main and Tail Rotor System-Servicing . . . . . . . . . . 1-7 Mission Antenna Mount Linear Actuator-
Main Beams at Station 129 (AVIM-Repair Aft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-316
of Cracked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 2-65 Mission Antenna Mount Linear Actuator-
Main DC Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-60 Forward . . . . . . . . . . . . . . . . . . . . . . .... . . . . . . . . . . . . . . . . . . . .. 9-297
Main Driveshaft P/N 205-040-004 . ........ 6-13 Mission Antenna Mount Alignment Proce
Main Driveshaft Assembly-Limits Chart dure-Aft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-322
P/N 205-040-004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-10 Mission Antenna Mount Alignment Proce-
Main Driveshaft Assembly and Installation dure-Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-303
P/N 205-040-004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-9 Mission Operator Seats . . . . . . . . . . . . . . . . . . . . . . . . . . 2-252.1, F2-48. 1
Main Driveshaft-Inspection Criteria for Mixing Lever Assembly-Cyclic Controls . . . 11-87
Spherical Inner Couplings . . . . . . . . . . . . . . . . . . . . . . . . . . F6-12 Mooring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Main Inverter Power Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-105 Mooring Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-204
Main Rotor Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27 Motor Driven Shutoff Valve . . . . . . . . . . . . . . . . . . . . . . 10-39
Main Rotor Blade, Composite . . . . . . . . . 5-34.2
Main Rotor Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

Index 8 Change 4
TM 55-1520-210-233

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Mount and Adapter-M6 Subsystem Oil System-Transmission ........................... 6-201


7.6MM, M60C Machine Gun ................ 16-56 Oil Tank, Engine......................................... 4-84
Muff Heater System Circuitry...................... 9-273 Oil Temperature Bulb-Engine .................... 8-90
M56 Mine Dispenser................................... 16-43 Oil Temperature Bulb-Transmission .......... 8-289
Oil Temperature Indicating System-Engine 8-78
N Oil Temperature Indicating System-
Transmission ....................................... 8-278
Navigation Instruments............................... 8-219 Oil Temperature Indicator-Engine.............. 8-80
Navigation Lights ........................................ 9-222 Oil Temperature Indicator-Transmission ... 8-280
Navigation Lights Flasher........................... 9-229 Outer Coupling Lubrication ........................ F6-6
Navigation Lights System........................... 9-218 Overhaul and Retirement Schedule........... T1-8
Navigation Lights System-Troubleshooting T9-13 Overheat Switch......................................... 13-34
Nonessential Bus Relay ............................. 9-87 Overvoltage Relay...................................... 9-85
Non-Self-Purging Particle Separator .......... 4-37
Non-Self-Purging Air Particle Separator- P
Inlet Screen..........................................
Cleaning ........................................ 4-34 Panel Assembly-Armament Control........... 16-89
Inspection ...................................... 4-32 Panel Assembly-Sight Light ....................... 16-93
Installation ..................................... 4-36 Panel-Hinged ............................................. 2-104
Removal ........................................ 4-33 Panel-Master Caution ................................ 9-173
Repair ............................................ 4-35 Panels-Cabin Floor .................................... 2-28
Nose Door .................................................. 2-77 Paratroop Static Line Cable ....................... 2-192
Nozzles, Registers, Gaskets and Misc Valves 13-4 Paratroop Static Line Cable ....................... 16-109
Parking ....................................................... 1-39
0 Part Numbers and Usable on Codes ......... 4-138
Particle Separator-Non-Self-Purging.......... 4-37
Oil Cooler Assembly................................... 6-217 Particle Separator Self-Purging-Air Inlet
Oil Cooler Assembly................................... 4-91 Filters................................................... 45
Oil Contamination, Chip Detector............... 4-101 Pedestal Lights-Instrument, Console ......... 9-160
Oil Debris Classification Chart (w/o ODDS)T6-5 Pilots Collective Stick ................................. 11-25
Oil Debris Classification Chart (w/ ODDS) . F6-14.2 Pilot-Static System ..................................... 8-163
ODDS Power Module ................................. 9-163.4 Plexiglass-Cleaning.................................... 1-18
Oil Filter-External................................. F6-57,6-204 Power Distributing System-Alternating
Oil Filter-Transmission ............................... 641 Current................................................. 9-89
Oil Jets........................................................ 6-60 Power Distribution System-Direct Current . 9-1
Oil Level Lights-Transmission .................... 9-236 Power Lever Controls................................. 4-110
Oil Level Sight Gages................................. 6-75 Power Plant Assembly ............................... 4-1
Oil Lines, Hoses, and Fittings..................... 4-77 Power Plant Electrical Cable Installation.... 4-153
Oil Pressure Indicator-Engine .................... 8-60 Power Receptacle-External........................ 9-47
Oil Pressure Indicating System-Engines .... 8-58 Power Relay-External................................. 9-54
Oil Pressure Indicating System-Trans........ 8-259 Power Relay-Main Inverter......................... 9-105
Oil Pressure Indicator-Transmission .......... 8-260 Power Relay-Spare Inverter....................... 9-107
Oil Pressure Switch-Engine........................ 4-147 Power System-External.............................. 9-43
Oil Pressure Transmitter-Engine ................ 8-69 Power Turbine N2 Tachometer Generator
Oil Pressure Transmitter-Transmission ..... 8-269 Installation............................................ 8-22
Oil Pump..................................................... 650 Premaintenance Requirements-Instrument8-8
Oil System .................................................. 4-74 Pressure Indicating System-Fuel ............... 8-121
Pressure Indicating System-Torque........... 8-141

Change 8 Index 9
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Pressure Indicator-Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 8-123 Relief Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-39


pressure Indicator-Torque. . . . . . . . . . . . 8-143 Repair of Cracked Spar Cap Angles on
Pressure Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... 6-67 Main Beams at Station 129 (AVIM) . . . . . . . . . . 2-65
Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... 7-53 Repair of Damage Penetrating Titanium
Pressure Tranmitter-Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-132 and Fiberglass Facings and Core-Honey
Pressure Transmitter-Torque . . . . . . . . . . . . . . . . . . . . . . 8-152 comb PaneL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-11
Pylon Fifth Mount Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62 Repair of Dents, Scars and Scratches
Pylon Mounts and Lift Link . . . . . . . . . . . . . . . . . . . . . . . 6-142 Honeycomb Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-6
Repair of Voids in Metal Surfaces Bonded
Panels . . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . . . . . . F2-10
Q
Repair or Replacement-Transmission
(AVIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-35
Quantity Indicating System-Fuel . . . . . . . .... 8-241 Replacement Chart-Connector . . . . . . . . . . . . . . . . . . . . F-9
Quantity Indicator-Fuel . . . . . . . . . . . . . . . . . . . . . . . . 8-243 Replacement Damaged Studs-Transmission
Quantity Transmitters-Fuel . . . . . . . . . . . . . . . . . . . 8-252 Assembly (AVIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36
Quill-Input Drive P/N 205-040-263 . . . . . . . 6-101 Requirements . . . . . . . . . . . . . . . .. ... . . . . . . . . . . . . . . . . . . C-5
Quill-Input Drive P/N 204-040-363 . . . . . . 6-92 Reservoir, Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Quill-Gen erator Drive .. .. . . . . . . . . .. .... 6-109 Rescue Hoist System Circuitry (Provisions)..
QuilIs-Input Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-286
6-90 Resistor-Thermocouple Lead Spool . . . . . . . . . . . . 8-111
R Retirement
“ Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-65
R Return to Overhaul-Transmission Assembly
(AVIM) . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . 6-38
Radar warning Indicating system (AN/ Reverse Current Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-81
APR-39) (When Installed) . . . . . . . . . . . . . . Rocket Launcher and Adapter . . . . . . . . . . . . . . . . . . . . . . . . 16-80
8-314
Radio Magnetic Indicators Rocket System XM3 . . . . . . . . . . . . . . . . . . . . . . . . .. . 16-76
(ID-998 )/ASN and ID-250( )/ARN). . . . . . . . . . . . RotorBlades-Cleaning . . . . . . . . . . . . . . . . . . . . .. . 1-19
8-223
Rearview Mirror. . . . . . . . . . . Rotor Blades, Composite ............. 5-34.2
2-175
Receptacle-Engine Vibration Meter . . . . . . . Rotor Blades-Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-114
9-120
Receptacle-External Power . . . . . . . . . . . . . . . . . Rotor Hub, Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
9-47
Receptacle-Heated Blanket . . . . . . . . . . . .. . . Rotor System Main.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
9-276
R e f e r e n c e s Appendix A. . . . . . . . . . . . . Rotor System Torque Values . . . . . . . . . . . . . . . . . . . . . . . F5-5
A-1
Registers, Gaskets and Miscellaneous Rotor Tachometer Generator . . . . . . . . . . . . . . . . . . . . . . . . . 8-31
Valves-Ducts-Nozzles . . . . . . . . . . . . . RPM Limit Warning Detector . . . . . . . . . . . . . . . . . . . . . . 9-186
13-4
Regulator-Voltage . . . . . . . . . . . . . RPM Limit Warning Detector-Bench
9-71
Reinforced Floor Mounting Plates and Test set Up . . . . . . . . . . . . . . . . . . .... . . . . . . . . . . . . . . . . . . . . . F9-10
Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-18.2, 2-27.1 RPM Limit Warning Detector-Cables for
Relay Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9-9
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning Detector-SDI Model. F9-8
9-39
Battery Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning Detector Models-
941
Bus Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Isolation of Circuits for Alignment . . . . . . . . . . . . T9-9
9-83
External Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning Detector-Saturn
9-54
Generator Field. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9-7
9-79
Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning Detector-SDI Model F9-8
9-109
Main Inverter Power.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning System . . . . . . . . . . . . . . . . . . . . . . 9-181
9-105
Nonessential Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM Limit Warning System-Trouble-
9-87
Overvoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T9-10
9-85
Reverse Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-81
Spare Inverter Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-107

Index 10 Change 4
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

S Shunt-Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sight Assembly, Mark 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-69
16-97
Sight Gages-Oil Level . . . . . . . . . . . . . . . . . . . . . . . . ...... . . 6-75
Saturn Model RPM Limit Warning Detector. F9-7 16-93
Sight Light Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scale and Friction Error Tolerances Plus Sight Station-M6 Subsystem 7.62MM
or Minus 0 Celsius-EGT Indicator . . . . . . . . . . . T8-6
16-68
M60C Machine Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schedule-Retirement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-65
Siphon Breaker Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-65
Schematic Diagram-Combustion Air Blower F13-6
Skid Saddles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Schematic Diagram-Electric Motor Assembly F12-6
Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Schematic Diagram-Fuel Quantity Installation Skid-Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-298
(Crashworthy) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8-5
Skid Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Schematic-Icing System Test Box . . . . . . . . . . . . . . . F9-3 F2-15
Skin and Stringer Repair-Combined . . . . . . . . . . .
Scissors and Sleeve Asembly . . . . . . . . . . . . . . . . . 5-74 2-20
Skins-Sheet Metal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screens Manifolds, Fittings . . . . . . . . . . . . 6-81
Skins-Tailboom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-5
Searchlight and Landing System . . . . . . . . . . . . . . . . . . 9-196 5-74
Sleeve Assembly, Scissors and . . . . . . . . . . . . . . . . . . . . .
Seat Belts-Crew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-241
sling Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-51
Seat Belts-Troop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-261
Slip Indicator-Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-201
Seat Covers-Crew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 2-225
Smoke Generator Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . 16-21
Seat Cover/Stencil-Crew . . . . . . . . . ..... F2-45
Solenoid Valve-Start Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 9-136
Seat-Crew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-44
Solenoid Valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-60
Seat-Crew-Armored . . . . . . . . . . . . . . . . . . . . . . . . 2-247
Spar Cap Angles on Main Beams at Station
Seating Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... F2-49
129 (AVIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . 2-65
Seating Arrangement (EH-lH)..... . . . . . . . . . . . . . . . F2-49.1 F2-24
Spar Cap Angle Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seats-Troop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . 2-253
Spare Inverter Power Relay . . . . . . . . . . . . . . . . . . . . . . . 9-107
Self-Locking Nuts-Reuse . . . . . . . . . . . . . .. . 1-29
Special Inspection,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 1-58
Service Deck-Right and Left . . ... . . . . . . 2-19
Special Instructions-Engine Quick
Servicing . . . . . . . . . . . . . . . . . . . . .. . 1-1
Change Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-136
Auxiliary Fuel System . . . . . . . . . . . . . . . . . . . . . 1-4
Special Tools and Test Equipment . . . . . . . . . . . . . . . 1-24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 1-12 T1-2
Special Tools and Test Equipment . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 1-2
Spherical Couplings on Main Driveshaft-
Engine oil System . . . . . . . . . . . . . . . 1-5
Inspection Criteria P/N 204-040-010 . . . . ... F6-3
Ground Handing wheel Pump . . . . . . . . . . . 1-10
Splice Fabrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-24.2
Ground Handling wheel Tires . . . . . . . . . . . 1-11 F6-4
splined Nut-Limits . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Resevoir . . . ..... . . . . . .. 1-9
Spool Resistor-Thermocouple Lead . . . . . . . . . . . . 8-111
Intermediate (42 degree) and Tail Rotor Spray Nozzle-Combustion Heater-Ex-
(90 degree) Gearboxes. . . . . . . . . . . . . . . . . . . . . . 1-8 F13-4
ploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mail and Tail Rotor System . . . . . . . . . . . . . 1-7 5-35
Stabilizer Bar Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smoke Generator Subsystem Tank . . . . . . . 16-26
Standard Crew Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-44 2-216
Transmission Oil System . . . . . . . . . . . . . . . . . . . . 1-6 T1-4
Standard Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing Points Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1-1
Standard Torque Procedures and Require-
Servo Cylinder Assembly (Collective Control), ments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28
Hydraulic . . . . . . . ........ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-80
Standard Torque Values-Engine Quick
Servo Cylinder Assembly (Cyclic Control), Change Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-137
Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . 7-67
Standards of Serviceability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-57
Sheet Metal Skins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Standby Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-225
Sheet Metal Skins Forward Fuselage- Standby Compass-Troubleshooting . . . . . . . . . . . . T8-14
Classification of Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-6
Standby Generator (Starter Generator) . . . . . . . . . . 9-67
Short Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
Start Fuel Solenoid Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-136
Shoulder Harness and Inertia Rcxl-Crew Starter Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-126
Standard Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..- 2-231

Index 11
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Starter-Generator Installation . . . . . . . . . . . . . . . . 4-150 Tail Skid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-298


starting system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-122 Temperature Bulb-Engine Oil . . . . . . . . . . . . . . . . . . . . . 8-90
Static Line Cable-paratroop . . . . . . . . . . . . . . . . . . . . . . . . 2-192, F2-43 Temperature Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-101
Static Line Cable, Paratroop . . . . . . . . . . . . . . . . . . . . . 16-109 Temperature-Millivolts vs . . . . . . . . . . . . . . . . . . . . . . . . . . . T8-5
Storage of Aircraft-Appendix EL . . . . . . . . . . . . . . . E-1 Test Box Schematic-Icing System . . . . . . . . . . . . . . F9-3
strap splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2-24.3 Test Circuit (Crashworthy)-Indicator
F u s e l a g e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 2-3, F2-2 Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8-6
s tructure-Tailboom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-294 Test Connections, Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
Structural Repair Materials . . . . . . . . . . . . . . . . . . . . . . . . . . T2-1 Testing Windshield Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F12-8
Studs-Torque Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1-6 Thermal VaIve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-211
Support Assemblies .. .... .. . . . . .... 11-72.1 Thermocouple Lead Spool Resistor . . . . . . . . . . . . . . . 8-111
Support Equipment . . . . . . . . . . . . . . . . . . . . . . 1-26 Thermostat-Cabin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-47
support-External Stores. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1 Tool Application-Use of Alignment Tool
Support Fittings-Tail Rotor Driveshaft...... 6-174 set (T47) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-8
Suppressor-Heat .... . . . . . . . . . . . . . 2-273 Torque Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1-3
Swashplatc and Support Assembly ..... 5-57 Torque Chart.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1-4
Torque Procedures and Requirements
standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1-28
T Torque Values for Fluid Connectors . . . . . . . . . . . . . . T1-5
Torque Values for Studs . . . . . . . . . . . . . . . . . . . . . . . . . T1-6
Tachometer Drive Quill-Hydraulic Pump... 6-118 Torque Values, Standard—Engine Quick
Tachometer-Dual . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Change Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-137
Tachometer—Dual— Troubleshooting. . . . . . . . T8-1 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34, F1-8
Tachometer Generator-Gas Producer. . . . . . . . . . . . . 8-49 Tracking and Operational Check . . . . . . . . . . . . . . . . . . . 5-120
Tachometer Generator Installation Gas Tracks-Cargo Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 2-137
Producer N1 . . . . . . . . . . . . .. . . . . . . 4-151 Transformer-AC . . . . . . . . . . . . . . . . . 9-113
Tachometer Generator Installation, Power Transmission and Engine Cowling . . . . . . . . . . . . F2-20
Turbine N2 . . . . ..... 4-152 Transmission Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
Tachometer Generator-Power Turbine . . 8-22 Transmission Assembly-Build-up-Unit-
Tachometer G e n e r a t o r - R o t o r . . . 8-31 versal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-15
Tachometer Indicating s y s t e m s . . . .. 8-12 Transmission Assembly and Gearboxes-
Tachometer Indicator Producer. . . . . . . . . . . . . . . . . . . . 8-40 Identification of MetaI Particles . . . . . . . . . . . . . . . . . 6-30, F6-14
TaiIboom Assembly. . . . . . . . . . . . . . . . .. . . 2-280 Transmission Assembly (AVIM)-Replace-
Tailboom Skins . . . ... . . . . . . . . . . . . . F2-5 meat Damaged Studs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36
Tailboom Structure ................. . . ... . . .... . . .. 2-294 Transmission Assembly-Universal Basic
Tailpipe-Exhaust System . . . . . . . . . . . . . . . . . . .. .. . . . . . . . 4-67 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-18
Tailpipe Faking . . . . . . .. . . . . . . . . . 2-51 Transmission Cowling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Tail Rotor Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5-114 Transmission Oil Falter . . . . . . . . . . . . . . . . . . . . . .F6-20, 6-41, F6-21
Tail Rotor Control Chain Conversion Pro- Transmission Oil Level Light . . . . . . . . . . . . . . . . . . . . . . . . 9-236
cedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-154 Transmission Oil Level Light-Trouble-
Tail Rotor Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-108 shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T9-14
Tail Rotor Crosshead Controls . . . . . . . . . . . . . . . . . . 5-107 Transmission Oil Pressure Indicating System 8-258
Tail Rotor Drive Quill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-125 Transmission Oil Pressure Indicator . . . . . . . . . . . . . . 8-260
Tail. Rotor Driveshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-159 Transmission Oil pressure Transmitter . . . . . . . . . . 8-269
Tail Rotor Driveshaft Support Flings. . . . . . . ... 6-174 Transmission Oil System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-201
Tail Rotor Gearbox . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6-52 6-190 Transmission OiI System-Servicing . . . . . . . . . . 1-6
Tail Rotor Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-98 Transmission Oil Temperature Bulb . . . . . . . . . . ..-. 8-289
Tail Rotor Hub and Blade Assembly . . . . . . . . . . . . . 5-88 Transmission Oil Temperature Indicating
Tail Rotor Hydraulic Cylinder and Support... 11-163.1 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-278
Tail Rotor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-85

Index 12
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph Paragraph

Transmission Oil Temperature Indicator . . . . . . . 8-280 Troubleshooting Cargo Suspension Assembly T14-3
Transmission Vent Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-68 Troubleshooting Inverter System . . . . . . . . . ..... T9-5
Transmission Pressure Transmitter and Troubleshooting Landing and Search-Light
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-16 system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T9-11
Transmitter and Switch-Transmission Troubleshooting Main Driveshaft
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... F6-16 P/N 205-040-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616, T6-2
Transmitter-Engine Oil Pressure . . . . . . . . . . . . . . . . . 8-69 Troubleshooting Navigation Lights System . T9-13
Transmitter-Fuel Pressure . . . . . . . . . . . . . . . . . . . . . . . . 8-132 Troubleshooting RPM Limit Warning System T9-10
Transmitter-Torque Pressure . . . . . . . . . . . . . . . . . . . . 8-152 Troubleshooting Standby Compass . . . . . . . . . . . . . . . . T8-14
Transmitter-Transm ission Oil Pressure . . . . . . 8-269 Troubleshooting Starter System . . . . . . . . . . . . . . . . . . . . . T9-6
Transmitters-Fuel Quantity .. . . . . . 8-252 Troubleshooting Torque Pressure Indicator.. T8-8
Repair or Replacement . . . . . . . . . . . . . . . . . .. . 8-256 Troubleshooting-Transmission Oil Level
Treating Corroded Parts-Cleaning. . . . . . . . . . . . . . . . . . . . . . T2-4 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T9-14
Trigger Detent Mechanism. . . . . . . . . . ... 11-64.1 Troubleshooting-Turn and Slip Indicator.. T8-12
Troop Seat Belts ..... . . . . . . . . 2-261 Troubleshooting-Transmission Assembly . . . T6-4
Troop Seats .. . . . . . . . . . ... 2-253 Troubleshooting Vertical Velocity Indicator. T8-13
Troubleshooting-Air Distribution System Truck Ground Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Helicoptors S/N 62-12351 through 64-13901 T13-1 Tube and Lever Assembly-cyclic Controls 11-65
Troubleshooting-Airspeed Indicator. . . . . . . .. T8-9 Tubes-cyclic Control System Control........ 11-95
Troubleshooting Anti-Collision Light System T9-12 Turn and Slip Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-201
Troubleshooting-Attitude Indicator. . . . . . . . . . . . T8-1 1 Turn and Slip Indicator-Troubleshooting.... T8-12
Troubleshoot ing-Barometric Altimeter. . . . . . . . . . . . . . . . . .. T8-10 Twenty Minutes Fuel Warning System
Troubleshooting Battery System. . . . . . . . . . . . . . . . . . . . T9-1 Float Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-87
Troubleshooting Clock ..... . . . . . . . . . . . . . . . T8-15
Troubleshooting Cockpit LIghts. . . . . . . . . . . . . . . . . . . . . . . . . . T9-8
Troubleshooting Converter Assembly . . . . . . . . . . . . . . . . . . T12-3 U
Troubleshooting DC VoItmeter. . . . . . . . . . . . . . . . . . . . . . . . . T8-17
Troubleshooting Dual Tachometer. . . . . . . . . . . . . . . . T8-1 UH-1H/V Composite Main Rotor Blade F5-26.1
Troubleshooting-Electric Motor Assembly. . . . . . . . . . . . . T12-2 Universal Transmission Assembly-Basic
Troubleshooting Engine De-Ice Circuitry T9-15 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6-18
Troubleshooting Engine OiI Pressure Indi- Universal Transmission Assembly-Build-up F6-15
cater . . . . . . . . . . . . . . . . . . . . . . . . . T8-2 Upper Door Window-Crew Door . . . . . . . . . . . . . . . . 2-140
Troubleshooting Engine Oil Temperature Use of the Maintenance Allocation Chart ... B-2
Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . T8-3 Use of Tool Set (T47)-Tool Application . ... F6-8
Troubleshooting Exhaust Gas Temperature
Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V
Troubleshooting External Power System T9-2
Troubleshooting Fire Detector ____ T12-1
Troubleshooting Force Trim System Circuitry Valve Control Temperature . . . . . . . . . . . . . . . . . . . 13-101
T9-17
Troubleshooting Fuel Pressure Indicator . . . . . Valve-Pressure Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-67
T8-7
Troubleshooting Fuel Quantity Indicator .... T8-16 Valve-Start Fuel Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-136
Troubleshooting Generator and DC Bus Valve-Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-211
Velocity Indicator-Vertical . . . . . . . . . . . . . . . . . . . . . . . . . . 8-210
System (Helicopters Prior to S/N 66-746).. T9-3
Troubleshooting Generator and DC Bus Vent Blower-Combustion Heater . . . . . . . . . . . . . . . . 13-67
System (Helicopter S/N 66-746 and Sub- Ventilation Air Scoop Assemblies . . . . . . . . . . . . . 13-9
sequent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vertical Velocity Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-210
T9-4
Troubleshooting 5-Volt Instrument Lighting Vibration Meter Receptacle--Engine . . . . . . . . . . . . 9-120
Vibrex Chart for Vertical l/Rev on
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-. T9-4 1 UH-1H/V
Troubleshooting Governor Control System ..................................... F5-87.1
Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T9-16

Change 4 Index 13
TM 55-1520-210-23-3

ALPHABETICAL INDEX (Continued)

Paragraph

Voltage Regulatory . . . . . . . . . . . 9-71


Voltmeter-AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-298
Voltmeter-DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 8-300
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-302

W
Warning Detector-RPM Limit ...................... 9-186
Warning Indicating System (AN/APR-39)
When Installed. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 8-314
Warning System-RPM Limit . . . . . . . . . . . . . . . . . . . . 9-181
Wheels and Tire Assembly-Ground Handling
Gear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41
Window-Adjustable-Crew Door . . . . . . . . . . . . . . . . . . . . .. 2-154
Window-Forward Crew Door. . . . . . . . . . . . . . . .. 2-147
Window-Upper-Crew Door . . . . . . . . . . . . . . . . . . . . . . . . . . 2-140
Windows-Cabin-Lo wer Forward . . . . . . . . . . . 2-168
Windows-Cabin Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-161
Windows-Crew Door Remove/Install . .. .. . . . . . . . . . . F2-42
Windshield. . . . . . . . . . . . . . . . . . . 2-133
Windshield and Windows Critical Areas
and Repair Limits........ . . . . . . . . . . . . . . F2-41
Windshield Installation . . . . . . . . . . . . . . . . . . . . . . . . F2-40
Windshield Wiper. . . . . . . . . . . . . . . . . . . . . . . . 12-9
Windshield Wiper Installation . . . . . . . . . . . . . . . . . . . . . . F12-2
Windshield Wiper System Circuitry . . . . . . . . . . . . . . . . . 9-280
Windshield Wiper—Testing . . . . . . . . . . . . . . . . . . . F12-8
Wiper Shaft Positioning . . . . . . . . . . . . . . . . . . . . . .. F12-5
Wiper System Circuitry-Windshield . . . . .. 9-280
Wiper-Windshield. . . . . . . . . . . . . . . . . . 12-9
Wiper Windshield -Installation .. . . . . . . . . . . . . .. F12-2
Wiring Data ....... . . . . . . . . . . . . . . F-3
Abbreviations . . . . . . . . . . . . . . . . . . . . .. F-5
symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-6
Wiring Identification . . . .
Wiring Diagram Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. F-13

x, Y, z

Index 14 Change 4
By Order of the Secretary of the Army:

CARL E. VUONO
General, United States Army
Official: Chief of Staff

R.L. DILWORTH
Brigadier General, United States Army
The Adjutant General

Distribution:

To be distributed in accordance with DA Form 12-31, AVUM and AVIM requirements


for UH-1H/V Helicopter, Utility, EH-1H, Helicopter, Electronic Countermeasure and
EH-1X Helicopter, Electronic Countermeasure & Intercept.
These are the instructions for sending an electronic 2028
The following format must be used if submitting an electronic 2028. The subject line must be
exactly the same and all fields must be included; however only the following fields are
mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27.
From: “Whomever” <[email protected]>
To: [email protected]
Subject: DA Form 2028
1. From: Joe Smith
2. Unit: home
3. Address: 4300 Park
4. City: Hometown
5. St: MO
6. Zip: 77777
7. Date Sent: 19--OCT--93
8. Pub no: 55--2840--229--23
9. Pub Title: TM
10. Publication Date: 04--JUL--85
11. Change Number: 7
12. Submitter Rank: MSG
13. Submitter FName: Joe
14. Submitter MName: T
15. Submitter LName: Smith
16. Submitter Phone: 123--123--1234
17. Problem: 1
18. Page: 2
19. Paragraph: 3
20. Line: 4
21. NSN: 5
22. Reference: 6
23. Figure: 7
24. Table: 8
25. Item: 9
26. Total: 123
27. Text:
This is the text for the problem below line 27.
Use Part II (reverse) for Repair Parts and Spe- DATE
RECOMMENDED CHANGES TO PUBLICATIONS AND cial Tool Lists (RPSTL) and Supply Catalogs/
Supply Manuals (SC/SM)
BLANK FORMS
For use of this form, see AR 25--30; the proponent agency is ODISC4. 8/30/02
TO: (Forward to proponent of publication or form)(Include ZIP Code) FROM: (Activity and location)(Include ZIP Code)
Commander, U.S. Army Aviation and Missile Command MSG, Jane Q. Doe
ATTN: AMSAM--MMC--MA--NP 1234 Any Street
Redstone Arsenal, AL 35898 Nowhere Town, AL 34565
PART 1 -- ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER DATE TITLE Organizational, Direct Support, And General
Support Maintenance Manual for Machine Gun, .50
TM 9--1005--433--24 16 Sep 2002 Caliber M3P and M3P Machine Gun Electrical Test Set
Used On Avenger Air Defense Weapon System
ITEM PAGE PARA-- LINE FIGURE TABLE
RECOMMENDED CHANGES AND REASON
NO. NO. GRAPH NO. * NO. NO.

1 WP0005 2 Test or Corrective Action column should identify a different WP number.


PG 3

* Reference to line numbers within the paragraph or subparagraph.


TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/ SIGNATURE
AUTOVON, PLUS EXTEN-
SION
MSG, Jane Q. Doe, SFC 788--1234
DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED. USAPA V3.01
TO: (Forward direct to addressee listed in publication) FROM: (Activity and location) (Include ZIP Code) DATE
Commander, U.S. Army Aviation and Missile Command MSG, Jane Q. Doe
ATTN: AMSAM--MMC--MA--NP 1234 Any Street
8/30/02
Redstone Arsenal, AL 35898 Nowhere Town, AL 34565
PART II -- REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER DATE TITLE

TOTAL NO.
PAGE COLM LINE NATIONAL STOCK REFERENCE FIGURE ITEM OF MAJOR
RECOMMENDED ACTION
NO. NO. NO. NUMBER NO. NO. NO. ITEMS
SUPPORTED

PART III -- REMARKS (Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)

TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/AUTOVON, SIGNATURE


PLUS EXTENSION

MSG, Jane Q. Doe, SFC 788--1234


USAPA V3.01
Use Part II (reverse) for Repair Parts and Spe- DATE
RECOMMENDED CHANGES TO PUBLICATIONS AND cial Tool Lists (RPSTL) and Supply Catalogs/
Supply Manuals (SC/SM)
BLANK FORMS
For use of this form, see AR 25--30; the proponent agency is ODISC4.

TO: (Forward to proponent of publication or form)(Include ZIP Code) FROM: (Activity and location)(Include ZIP Code)
Commander, U.S. Army Aviation and Missile Command
ATTN: AMSAM-MMC-MA-NP
Redstone Arsenal, AL 35898

PART 1 -- ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER DATE TITLE

TM 55-1520-210-23-3
ITEM PAGE PARA-- LINE FIGURE TABLE
RECOMMENDED CHANGES AND REASON
NO. NO. GRAPH NO. * NO. NO.

* Reference to line numbers within the paragraph or subparagraph.


TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/ SIGNATURE
AUTOVON, PLUS EXTEN-
SION

DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED. USAPA V3.01
TO: (Forward direct to addressee listed in publication) FROM: (Activity and location) (Include ZIP Code) DATE
Commander, U.S. Army Aviation and Missile Command
ATTN: AMSAM-MMC-MA-NP
Redstone Arsenal, AL 35898

PART II -- REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER DATE TITLE
TM 55-1520-210-23-3
TOTAL NO.
PAGE COLM LINE NATIONAL STOCK REFERENCE FIGURE ITEM OF MAJOR
RECOMMENDED ACTION
NO. NO. NO. NUMBER NO. NO. NO. ITEMS
SUPPORTED

PART III -- REMARKS (Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)

TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/AUTOVON, SIGNATURE


PLUS EXTENSION

USAPA V3.01
The Metric System and Equivalents

Linear Measure Liquid Measure

1 centiliter = 10 milliters = .34 fl. ounce


1 centimeter = 10 millimeters = .39 inch 1 deciliter = 10 centiliters = 3.38 fl. ounces
1 decimeter = 10 centimeters = 3.94 inches 1 liter = 10 deciliters = 33.81 fl. ounces
1 meter = 10 decimeters = 39.37 inches 1 dekaliter = 10 liters = 2.64 gallons
1 dekameter = 10 meters = 32.8 feet 1 hectoliter = 10 dekaliters = 26.42 gallons
1 hectometer = 10 dekameters = 328.08 feet 1 kiloliter = 10 hectoliters = 264.18 gallons
1 kilometer = 10 hectometers = 3,280.8 feet
Square Measure
Weights
1 sq. centimeter = 100 sq. millimeters = .155 sq. inch
1 centigram = 10 milligrams = .15 grain 1 sq. decimeter = 100 sq. centimeters = 15.5 sq. inches
1 decigram = 10 centigrams = 1.54 grains 1 sq. meter (centare) = 100 sq. decimeters = 10.76 sq. feet
1 gram = 10 decigram = .035 ounce 1 sq. dekameter (are) = 100 sq. meters = 1,076.4 sq. feet
1 decagram = 10 grams = .35 ounce 1 sq. hectometer (hectare) = 100 sq. dekameters = 2.47 acres
1 hectogram = 10 decagrams = 3.52 ounces 1 sq. kilometer = 100 sq. hectometers = .386 sq. mile
1 kilogram = 10 hectograms = 2.2 pounds
1 quintal = 100 kilograms = 220.46 pounds Cubic Measure
1 metric ton = 10 quintals = 1.1 short tons
1 cu. centimeter = 1000 cu. millimeters = .06 cu. inch
1 cu. decimeter = 1000 cu. centimeters = 61.02 cu. inches
1 cu. meter = 1000 cu. decimeters = 35.31 cu. feet

Approximate Conversion Factors

To change To Multiply by To change To Multiply by

inches centimeters 2.540 ounce-inches Newton-meters .007062


feet meters .305 centimeters inches .394
yards meters .914 meters feet 3.280
miles kilometers 1.609 meters yards 1.094
square inches square centimeters 6.451 kilometers miles .621
square feet square meters .093 square centimeters square inches .155
square yards square meters .836 square meters square feet 10.764
square miles square kilometers 2.590 square meters square yards 1.196
acres square hectometers .405 square kilometers square miles .386
cubic feet cubic meters .028 square hectometers acres 2.471
cubic yards cubic meters .765 cubic meters cubic feet 35.315
fluid ounces milliliters 29,573 cubic meters cubic yards 1.308
pints liters .473 milliliters fluid ounces .034
quarts liters .946 liters pints 2.113
gallons liters 3.785 liters quarts 1.057
ounces grams 28.349 liters gallons .264
pounds kilograms .454 grams ounces .035
short tons metric tons .907 kilograms pounds 2.205
pound-feet Newton-meters 1.356 metric tons short tons 1.102
pound-inches Newton-meters .11296

Temperature (Exact)

°F Fahrenheit 5/9 (after Celsius °C


temperature subtracting 32) temperature
PIN: 040153-000

You might also like